小实验配置3

BGP

实验拓扑图

R1

[R1]int l0
[R1-LoopBack0]ip address 192.168.1.1 24
[R1-LoopBack0]int g0/0
[R1-GigabitEthernet0/0]ip address 100.1.1.1 24

R2

[R2]int g0/0
[R2-GigabitEthernet0/0]ip address 100.1.1.2 24
[R2-GigabitEthernet0/0]ping 100.1.1.1
[R2-GigabitEthernet0/0]int g0/1
[R2-GigabitEthernet0/1]ip address 100.2.2.2 24
[R2-GigabitEthernet0/1]int l0
[R2-LoopBack0]ip address 2.2.2.2 32

R3

[R3]int l0
[R3-LoopBack0]ip address 3.3.3.3 32
[R3-LoopBack0]int g0/0
[R3-GigabitEthernet0/0]ip address 100.2.2.3 24
[R3-GigabitEthernet0/0]ping 100.2.2.2
[R3-GigabitEthernet0/0]int g0/1
[R3-GigabitEthernet0/1]ip address 100.3.3.3 24

R4

[R4]int l0
[R4-LoopBack0]ip address 4.4.4.4 32
[R4-LoopBack0]int g0/0
[R4-GigabitEthernet0/0]ip address 100.3.3.4 24
[R4-GigabitEthernet0/0]ping 100.3.3.3
[R4-GigabitEthernet0/0]int g0/1
[R4-GigabitEthernet0/1]ip address 100.4.4.4 24

R5

[R5]int l0
[R5-LoopBack0]ip address 192.168.2.1 24
[R5-LoopBack0]int g0/0
[R5-GigabitEthernet0/0]ip address 100.4.4.5 24
[R5-GigabitEthernet0/0]ping 100.4.4.4

R2

[R2]ospf 1
[R2-ospf-1]area 0
[R2-ospf-1-area-0.0.0.0]network 100.2.2.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0

R3

[R3]ospf 1
[R3-ospf-1]area 0
[R3-ospf-1-area-0.0.0.0]network 100.2.2.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 100.3.3.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 3.3.3.3 0.0.0.0

R4

[R4]ospf 1
[R4-ospf-1]area 0
[R4-ospf-1-area-0.0.0.0]network 4.4.4.4 0.0.0.0
[R4-ospf-1-area-0.0.0.0]network 100.3.3.0 0.0.0.255

R2

[R2]ping 4.4.4.4

R4

[R4]ping 2.2.2.2

R1

[R1]bgp 100
[R1-bgp-default]peer 100.1.1.2 as 200
[R1-bgp-default]add ipv4
[R1-bgp-default-ipv4]peer 100.1.1.2 enable
[R1-bgp-default-ipv4]net 192.168.1.0 24

R2

[R2]bgp 200
[R2-bgp-default]peer 100.1.1.1 as 100
[R2-bgp-default]peer 4.4.4.4 as 200
[R2-bgp-default]peer 4.4.4.4 con lo 0
[R2-bgp-default]add ipv4
[R2-bgp-default-ipv4]peer 4.4.4.4 enable
[R2-bgp-default-ipv4]peer 100.1.1.1 enable
[R2-bgp-default-ipv4]peer 4.4.4.4 next-hop-local

R4

[R4]bgp 200
[R4-bgp-default]peer 2.2.2.2 as 200
[R4-bgp-default]peer 100.4.4.5 as 300
[R4-bgp-default]peer 2.2.2.2 con lo 0
[R4-bgp-default]add ipv4
[R4-bgp-default-ipv4]peer 2.2.2.2 enable
[R4-bgp-default-ipv4]peer 100.4.4.5 enable
[R4-bgp-default-ipv4]peer 2.2.2.2 next-hop-local

R5

[R5]bgp 300
[R5-bgp-default]peer 100.4.4.4 as 200
[R5-bgp-default]add ipv4
[R5-bgp-default-ipv4]peer 100.4.4.4 enable
[R5-bgp-default-ipv4]network 192.168.2.0 24

R2

[R2]ospf 1
[R2-ospf-1]import-route bgp

R4

[R4]ospf 1
[R4-ospf-1]import-route bgp
 

1.R3上检查其ospf邻居

2.在R2和R4上分别ping对方的环回口地址

R2

R4

3.分别在R2和R4上使用dis bgp peer ipv4检查其邻居

R2

R4

4.在R3上检查其路由表

5.R1pingR5