中科可控H620-G30 BIOS BMC固件

; ASPEED iRMP SOC Flash Utility ReadME ;=============================================================================== 1.Platform Requirement: - DOS Environment - Support ASPEED Chips >> AST1000/2000 A1 and after >> AST1100/2050/2100/2150/2200 >> AST2300/1300/1050 >> AST2400/1400 >> AST2400/1400 + AST1070 >> AST1010 >> AST2500 2.Flash Utility Usage (New Interface): - Format: >> socflash [operand] ++ operand list +++ if=the update file +++ of=the backup file +++ is=the input string ++++ blank is not allowed in the string and the length of the string is below than 40 bytes ++++ example: is=11:22:33:44:55:66 +++ bus=PCI device bus number +++ cs=chip select ++++ AST1000/2000: 0/1 (default: 0) ++++ AST1100/2050/2100: 0/1/2 +++++ default: get from SCU trapping ++++++ if Boot Trapping is disabled, then set to 0 for AST2100, and 2 for others +++ flashtype=flash chip type ++++ 0/1/2/3: NOR/NAND/SPI/SYS SPI Flash +++++ SYS SPI: AST2500/2400/1400/2300/1300/1050 only +++ width= NOR flash bus width ++++ 8/16: AST2400/1400/2300/1300/1050 ++++ 8 : AST2100/2200 ++++ 16 : AST2000 +++ skip=the skip size in bytes at the start of input file (default=0) +++ offset=the offset in bytes at the start of the flash (default=0) +++ count=the size in bytes copy to the flash (default=the size of the flash) +++ backupcount=the size in bytes backup from the flash (default=the size of the flash) +++ lpcport=the LPC port number (0x2e/0x4e) (it is required for "option=l") +++ writeclk/readclk/eraseclk: SPI Write CLK/Read CLK/EraseCLK ++++ writeclk=50 ; The Max. SPI Write CLK is 50MHz +++ gpio_b/gpio_f=set gpio before/after flash update program execute ++++ support chips: AST1100/2050/2100/2150/2200/1300/2300/1400/2400 ++++ limitation: max. gpio set: 10 ++++ format:[port+pin+data ....] ++++ example: gpio_b=c41a71 means set GPIO C4 to 1, A7 to 1 before program execute ++++ example: gpio_f=c40a70 means set GPIO C4 to 0, A7 to 0 after program execute +++ reginit_b/reginit_f=Reg. Table File ++++ set ARM interface reg. before/after flash update ++++ command example: reginit_b=reginit.inf ++++ reg. file format: [addr] [mask] [data] +++++ ex: 0x1e6e2000 0xffffffff 0x1688a8a8 ; write 0x1688a8a8 to 0x1e6e2000 +++++ notes: skip the command if add ";" at the first of the line +++ option=f|c|2|r|d|x|l|i|m|w ++++ f: skip the comparision of flash data and force to update ++++ c: use chip erase instead of sector erase ++++ r: reset scratch ++++ d: disable ARM after update flash ++++ 2: two flash update support +++++ AST1100/2050/2100: two SPI solution: 1st SPI is on CS2; 2nd SPI is on CS0 +++++ AST2000: two NOR Flash Solution: 1st Flash is on CS0; 2nd Flash is on CS1 ++++ x: low speed mode (SPI only) +++++ use this option if can' find SPI flash or update properly in normal mode ++++ l: Update firmware through LPC path +++++ AST2400/1400/2300/1300/1050 only ++++ i: Update Firmware Image to Flash only if Image and Flash Size are the same ++++ m: Update firmware through co-processor +++++ AST2400/1400 + AST1070 only ++++ w: Trigget WDT reset only >> example: ++ socflash if=new.bin of=old.bin option=f +++ update the firmware image to new.bin +++ bacup the old firmware to old.bin +++ force to update without comparision 3.Flash Utility Usage (Legacy Interface): - Format: >> Normal: SOCFlash [the update soc file*] [the backup file*] [Chip Select] [Flash Type] [Start Offset] [Programming Size] >> Backup Only: SOCFlash -b [the backup file*] [Chip Select] [Flash Type] [Start Offset] [Programming Size] >> Skip Backup: SOCFlash -s [the update soc file*] [Chip Select] [Flash Type] [Start Offset] [Programming Size] ++ The fields add * means must have - Options: >> Chip Select: ++ AST1000/2000: 0/1 (default: 0) ++ AST1100/2050/2100: 0/1/2 +++ default: get from SCU trapping ++++ if Boot Trapping is disabled, then set to 0 for AST2100, and 2 for others >> Flash Type: (AST1100/2050/2100) ++ 0/1/2: NOR/NAND/SPI >> Start Offset: start offset from image file (default: 0x0) >> Programming Size: The size need to program to Flash - Example: socflash all.bin old.bin 4.Return Code: - 0: success - 1: failed 5.Support Flash Chip List: - NOR: >> MXIC MX29LV640DT, MX29GL128E, MX29GL128DT/B, MX29GL256E >> Spansion S29xx064MxxR4, S29GL128Nx8, S29GL256Nx8 >> SST 39VF640 >> ST STM29W640F, M20EW256M, M29W256G, M29W640G - NAND: >> Micron MT29F2G08 >> Samsung K9F1G08U0A - SPI: >> Spansion S25FL64A, S25FL128P, S25FL128S >> SST 25VF016B, 25VF064C >> ST M65P64, M25P128 >> Winbond W25X16, W25X32, W25X64, W25Q16V, W25Q32BV, W25Q64BV, W25Q128BV >> MXIC MX25L12805D, MX25l2005C, MX25L3205D, MX25L6445E >> Numonyx N25Q128 >> ATMEL AT26DF321, AT25DF321, AT25DF161 >> [AST2300/2400] Spansion S25FL256S, S25FL512 >> [AST2300/2400] Winbond 25Q256/257 >> [AST2300/2400] MXIC MX25L25635E/F, MX25L25735E, MX66L512 >> [AST2300/2400] Numonyx N25Q256, N25Q512 6.FAQ - New Command Interface Support: >> Support New Command Interface after than v.0.90 - SOCFlash through LPC Path: AST1010/1050/1250 >> add "option=l" and assign LPC port, "lpcport=0x2e" for example. - SOCFlash through co-precessor: AST2400/1400 + AST1070 >> add "option=m" - New support chips from v.0.96 >> MXIC MX29GL128E, MX29GL256E >> SST 39VF640 >> ST M20EW256M, M29W256G - New support chips from v.0.97 >> ST M29W640G - New support chips from v.0.98 >> SST 25VF064C - New support chips from v.1.02 >> MXIC MX29GL128DT/B >> Winbond W25Q64BV, W25Q128BV >> Numonyx N25Q128 - New support chips from v.1.03 >> Winbond W25Q16V, W25Q32BV, W25X32 >> ATMEL AT26DF321, AT25DF321 >> MXIC MX25L3205D, MX25L6445E, MX25L25635E(AST2300), MX25L25735E(AST2300) - New support chips from v.1.05 >> Spansion S29GL064 8-bits mode for AST1300/2100/2150/2200/2300 - New support chips from v.1.06 >> Numonyx N25Q256, Spansion S25FL256S on AST1050/1300/2300 - New support chips from v.1.07 >> Numonyx N25Q512 on AST1050/1300/2300 >> MXIC MX25L25635F on AST1050/1300/2300 >> ATMEL AT25DF161 >> Winbond 25Q256FV - New support chips from v.1.08 >> Spansion S25FL128/256S 256KB sector size >> MXIC MX66L512 - New support chips from v.1.10 >> Winbond 25Q257 - New support chips from v.1.12 >> Spansion S25FL512 7.Contact Window: - [email protected] - 886.3.578.9568 ext. 810