Scribd
Cargar
3K vistas8 páginas

Procedimiento de Calibracion de Valvulas Toyota 3ZZ-FE y 4ZZ-FE

calibracion de valvulas corolla

Cargado por

juan carlos Pacheco
Derechos de autor
© © All Rights Reserved
Nos tomamos en serio los derechos de los contenidos. Si sospechas que se trata de tu contenido, reclámalo aquí.
Formatos disponibles
Descarga como PDF o lee en línea desde Scribd
3K vistas8 páginas

Procedimiento de Calibracion de Valvulas Toyota 3ZZ-FE y 4ZZ-FE

calibracion de valvulas corolla

Cargado por

juan carlos Pacheco
Derechos de autor
© © All Rights Reserved
Nos tomamos en serio los derechos de los contenidos. Si sospechas que se trata de tu contenido, reclámalo aquí.
Formatos disponibles
Descarga como PDF o lee en línea desde Scribd
Está en la página 1/ 8
ENGINE MECHANICAL VALVE CLEARANOE (327-FE'422-FE) VALVE CLEARANCE (3ZZ-FE/4ZZ-FE) ADJUSTMENT 1 REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 2 nuts, 2 clips and cylinder head cover. 2 REMOVE IGNITION COIL ASSY (@) Disconnect the 4 connectors. (b) Remove the 4 bolts and 4 ignition coils. 3. DISCONNECT ENGINE WIRE (a) Disconnect the connectors, (b) Remove the 3 clamps from the 3 clamp brackets, (©) Remove the bolt and nut installing the engine wire. 4. DISCONNECT VENTILATION HOSE (a) Disconnect the ventilation hose from the cylinder head cover. DISCONNECT VENTILATION HOSE NO.2 (a) Disconnect the ventilation hose from the cylinder head cover. 6. REMOVE CYLINDER HEAD COVER SUB-ASSY (a) Remove the 9 bolts, 2 seal washers, 2 nuts, 3 clamp brackets and cylinder head cover. 7. REMOVE ENGINE UNDER COVER RH HINT: marks as above. Timing Chain Ax Surface COROLLA REPAIR MANUAL (RME2SE) 8 SET NO.1 CYLINDER TO TDC/COMPRESSION (@) Turnthe crankshaft pulley, and align its groove with timing mark "0" of the timing chain cover. (b) Check that the point marks of the camshaft timing sprock- et and VVT timing sprocket are in straight line on the tim- ing chain cover surface as shown in the illustration, 14-87 If not, turn the crankshaft 1 revolution (360°) and align the 14-88 ENGINE MECHAN COROLLA REPAIR MANUAL (RME2SE) 9. (a) (b) «© 10. (a) L— VALVE CLEARANDE 72-F5N477-66) INSPECT VALVE CLEARANCE Check only the valves indicated. (1) Using a feeler gauge, measure the clearance be- tween the valve lifter and camshaft, (2) Record the out-of specification valve clearance measurements, They will be used later to determine the required replacement vaive lefter. Valve clearance (Cold): Intake 0.15 - 0.25 mm (0.006 - 0.010 in.) Exhaust 0.25 - 0.35 mm (0.010 - 0.014 in.) Tur the crankshaft 1 revolution (360 °) and set No. 4 cyl- inder to TDC/compression. Check only the valves indicated (1) Using a feeler gauge, measure the clearance be- tween the valve lifter and camshaft (2) Record the out-of specification valve clearance measurements, They will be used later to determine the required replacement vaive lefter. Valve clearance (Cold): Intake 0.15 - 0.25 mm (0.006 - 0.010 in.) Exhaust 0.25 - 0.35 mm (0.010 - 0.014 in.) REMOVE FAN AND GENERATOR V BELT Turn the V-ribbed belt tensioner slowly clockwise and loosen it. Then, remove the fan and generator belt and put back the V-ribbed belt tensioner little by litte and fix it quietly 14-89 ENGINE MECHANICAL VALVE CLEARANOE (327-FE'422-FE) 11. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (a) Place a wooden block between the jack and engine, and set the jack, then remove the 4 bolts, 2nuts and engine mounting insulator RH. 12, REMOVE V-RIBBED BELT TENSIONER ASSY (a) _ Remove the bolt, nut and V-ribbed belt tensioner. HINT: Handle a jack up and down to remove the bol. COROLLA REPAIR MANUAL (RME2SE) 13, ADJUST VALVE CLEARANCE NOTICE: Be cure not to revolve the crankshaft without the chain ten- sioner. (@) Set the No. + cylinder to the TDC/compression. (b) Place match marks on the timing chain and camshaft tim- ing sprockets. (co) Remove the 2 nuts and chain tensioner. (d) Fix the camshaft with a spanner and so on, then loosen the camshaft timing gear set bolt, NOTICE: Be careful not to damage the valve lifter.

También podría gustarte