Scribd
Upload
327 views

Aptransco Objective Questions MPMC

This document contains 24 multiple choice questions about microprocessors and microcontrollers. The questions cover topics like interrupts and their priorities, register types, interrupt triggering, interrupt masking, processor speeds, addressing, and differences between 8086 and 8088 microprocessors. An answer key is provided at the end.

Uploaded by

Ysdlv Prasad
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
327 views

Aptransco Objective Questions MPMC

This document contains 24 multiple choice questions about microprocessors and microcontrollers. The questions cover topics like interrupts and their priorities, register types, interrupt triggering, interrupt masking, processor speeds, addressing, and differences between 8086 and 8088 microprocessors. An answer key is provided at the end.

Uploaded by

Ysdlv Prasad
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

APTRANSCO OBJECTIVE QUESTIONS | MICROPROCESSOR ANS MICROCONTROLLERS MULTIPLE CHOICE QUESTIONS | APTRANSCO MULTIPLE CHOICE QUESTIONS HI FRIENDS THIS

MATERIAL USED FOR ALL OTHER EXAMS TOO

1. Which interrupt has the highest priority?


a) INTR b) TRAP c) RST6.5

2. In 8085 name the 16 bit registers?


a) Stack pointer b) Program counter c) a & b

3. Which of the following is hardware interrupts?


a) RST5.5, RST6.5, RST7.5 b) INTR, TRAP c) a & b

4. What is the RST for the TRAP?


a) RST5.5 b) RST4.5 c) RST4

5. What are level Triggering interrupts?


a) INTR&TRAP b)RST6.5&RST5.5 c)RST7.5&RST6.5

6. Which interrupt is not level sensitive in 8085?


a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

7. What are software interrupts?


a) RST 0 7 b) RST 5.5 7.5 c) INTR, TRAP

8. Which stack is used in 8085?


a) FIFO b) LIFO c) FILO

9. Why 8085 processor is called an 8 bit processor?


a) Because 8085 processor has 8 bit ALU. b) Because 8085 processor has 8 bit data bus. c) a & b.

10. What is SIM?


a) Select Interrupt Mask b) Sorting Interrupt Mask c) Set Interrupt Mask.

11. RIM is used to check whether, ______


a) The write operation is done or not b) The interrupt is Masked or not c) a & b

12. What is meant by Maskable interrupts?


a) An interrupt which can never be turned off. b) An interrupt that can be turned off by the programmer.

c) none

13. In 8086, Example for Non maskable interrupts are


a) Trap b) RST6.5 c) INTR

14. What does microprocessor speed depends on?


a) Clock b) Data bus width c) Address bus width

15. Can ROM be used as stack?


a) Yes b) No c) sometimes yes, sometimes no

16. Which processor structure is pipelined?


a) all x80 processors b) all x85 processors c) all x86 processors

17. Address line for RST3 is?


a) 0020H b) 0028H c) 0018H

18. In 8086 the overflow flag is set when


a) The sum is more than 16 bits b) Signed numbers go out of their range after an arithmetic operation c) Carry and sign flags are set d) During subtraction

19. The advantage of memory mapped I/O over I/O mapped I/O is,
a) Faster b) Many instructions supporting memory mapped I/O c) Require a bigger address decoder d) All the above

20. BHE of 8086 microprocessor signal is used to interface the


a) Even bank memory b) Odd bank memory c) I/O d) DMA

21. In 8086 microprocessor the following has the highest priority among all type
interrupts. a) NMI b) DIV 0 c) TYPE 255 d) OVER FLOW

22. In 8086 microprocessor one of the following statements is not true.


a) Coprocessor is interfaced in MAX mode

b) Coprocessor is interfaced in MIN mode c) I/O can be interfaced in MAX / MIN mode d) Supports pipelining

23. 8088 microprocessor differs with 8086 microprocessor in


a) Data width on the output b) Address capability c) Support of coprocessor d) Support of MAX / MIN mode

24. Address line for TRAP is?


a) 0023H b) 0024H c) 0033H

Key: 1.1 C 1.2 C 1.3 C 1.4 B 1.5 B 1.6 B 1.7 A 1.8 B 1.9 A 1.10 C 1.11 B 1.12 B 1.13 A 1.14 C 1.15 B 1.16 C 1.17 C 1.18 B 1.19 D 1.20 B 1.21 A 1.22 B 1.23 A 1.24 B

You might also like