Autohydro h

For WindowsTM

Users Manual
Release 5.0

Autoship Systems Corporation Suite 312 - 611 Alexander Street Vancouver BC V6A 1E1 Canada
Copyright 2004 Autoship Systems Corporation Windows TM is a trademark of Microsoft Corporation AutoCAD is a trademark of Autodesk, Inc.

Information contained in this document is subject to change without further notice. No part of this document may be reproduced or transmitted in any form, or by any means, electronic of mechanical, for any purpose, without the express permission of Autoship Systems Corporation.

Copyright 2004 Autoship Systems Corporation. All right reserved

Windows is a trademark of Microsoft Corporation. AutoCAD is a trademark of Autodesk Inc. All other product names are trademarks, registered trademarks, or service marks of their respective owners. Autoship Systems Corporation cannot attest to the accuracy of this information. In addition, terms suspected of being trademarks, registered trademarks, or service marks have been appropriately capitalized. Use of a term in this book should not be regarded as a validity of any trademark, registered trademarks, or service mark.

Autoship Systems Corporation Suite 312 611 Alexander Street Vancouver, B.C. V6A 1E1 Canada Tel: (604) 254-4171 Fax: (604) 254-5171 www.autoship.com

Table of Contents
Chapter 1 - Getting Started Introduction What Autohydro Can Do for You System Requirements Program Installation
System Initialization - Wise Installation Wizard AutoHydro Setup Program

1 1 2 3 4

Hardware Lock Installation

General Description Precautions Windows 95, Local Station Windows NT, Local Station Hardware Lock Installation, Network System

Starting and Exiting Autohydro Updating Autohydro Chapter 2 - About the Program Introduction How Autohydro Works
Parts of the Program Modelmaker Autohydro Commands

9 9 11 11 12

Key Concepts and Terms

File Types Geometry Files Data Hierarchy Part Component Shape Stations and Points Co-ordinate System Units Using Files from GHS/BHS Typical Job Flow

15

Chapter 3 - A Quick Sailthrough of Autohydro Introduction Modelmaker

Start Modelmaker Create a Part Create Component 1 Shape Component 1 Create Shaped Component 2 Join Components Save the File

21 21 22

Autohydro
Start Autohydro and Find Lightship Displacement Add Deck Cargo and Find Resultant Drafts Generate and Print a Report

28

ii

Chapter 4 - Tutorials Introduction Tutorial 1 - Modelmaker Project Using Menus and Screens
Add Tanks to the Barge Created in the Quick Sailthrough. Create Sounding Tubes for the Cargo Tanks Create a Deckhouse

33 33 34

Tutorial 2 - Running Autohydro Using Menus and Screens

Find Hydrostatics, Cross-Curves and Hull Data Find Drafts for a Given Weight and Center of Gravity

43

Tutorial 3 - Modelmaker Project Using Command Files

Create a Barge, LOLLIPOP.GF1

46

Tutorial 4 - Running Autohydro Using Commands

Obtain Basic Output from LOLLIPOP.GF1

49

Tutorial 5 - Modelling a Vessel Using Modelmaker Commands

Load a Command File Load a Second Command File

50

Tutorial 6 - How to Produce a Stability Book in Autohydro

Load a RUN File

52

Tutorial 7 - How to Assess Damage Stability in Autohydro

54

iii

Getting Started

Chapter 1
Getting Started
Introduction
This manual is interactive in nature, and is designed for use with Autohydro running. Later in Chapter 1 we will tell you how to install and run Autohydro, but first let's look at how to use this manual: To make the best use of this manual, first read the next section, What Autohydro can do for you. Then read section How Autohydro Works, which discusses basic concepts and terms that you need to understand to work effectively with Autohydro. Next, take the guided tour, A Quick Sailthrough. Then, you can learn and practice other features of the program by running through the tutorials presented in section 4. You will find it best to follow the sequence given and not jump ahead or do the tutorials at random because we are trying to progress from simple and easy tasks to increasingly complex ones. In addition to this manual, you will find further information in the Help system Reference Manual provided with the program.

Chapter 1

What Autohydro Can Do for You

Autohydro has the capability to analyse the hydrostatic characteristics of any kind of vessel under a wide variety of conditions. It is comprised of two main modules: Modelmaker, is used to model any vessel, from kayaks to supertankers, and also buoys, docks, storage tanks, drilling platforms and anything else that displaces and/or contains fluids. Autohydro, is used to perform hydrostatic and stability calculations, analyse hydrostatic and stability characteristics for various loading conditions including damage, produce graphic and text for reports such as stability books and tank sounding tables. Visit www.autoship.com for information on our full range of CAD/CAM products for vessel design and construction.

System Requirements

System Requirements
The following table shows the minimum and recommended system requirements for running Autohydro. Operating System Windows 98 Windows NT4 SP6a or later Windows 2000 Windows XP Professional SP1 Pentium 256 1024 X 768 with True Color 100 MB Free

Processor Memory Video Hard Disk

* Operation is possible at 256 colors, but for rendering to function correctly 32k colors or more are needed.

Chapter 1

Program Installation
System Initialization - Wise Installation Wizard

1. Install your hardware lock on the parallel port of your machine; installing the lock will not prevent you connecting other devices to this port. 2. Place the CD in your computer. 3. In most cases an "autorun" feature will start the installation program automatically; if it doesn't, then access the disk via either Windows Explorer or the Start/Run commands, and double-click the Setup 32 file. 4. A screen will open, listing all the applications available on the disk. Click the application you want to install. Note that if you do not have both a hardware lock and an authorization disk pertaining to that application, you will only be able to run the software in "Demo" mode. 5. A small dialogue will appear, asking you if you have an authorization disk. If you do, click Yes. Note that if you do not have both an Authorization Disk and a hardware lock, you will only be able to operate your software in "Demo" mode. 6. The Wise Installation Wizard will open, and will show a small dialogue informing you that your system will be initialized to accept ASC software. Click OK. 7. You will be asked if you wish to copy to your machine the lock driver files appropriate to your Windows version. In most cases it is advisable to click "Yes" . 8. Next you will be asked to specify the location for the lock drivers to be stored; accept the default or indicate a different location. Click OK.

Program Installation

9. A warning message will appear, notifying you that Setup will attempt to install the lock driver. It is advisable that you check to ensure your hardware lock is installed correctly; if it is not, then the program will only run in Demo mode.

AutoHydro Setup Program

10. The AutoHydro Setup program will now start. An information message will appear first. Ensure all other Windows programs are closed, and click Next. 11. Accept the default installation location, or use the Browse feature to specify another location. 12. Follow the remaining instructions to complete the installation. 13. If you already have AutoHydro installed on your machine, a dialogue will appear and require you to choose between keeping all existing settings or resetting all settings upon installation. Click the radio button corresponding to your choice, and click Next. 14. Before the installation process finishes, a dialogue will ask you if you want to update your HTML Help system. Click yes to install the latest updated system.

Chapter 1

Hardware Lock Installation

General
Description A hardware lock is a small electronic device that is installed onto the parallel port of your computer. (Note: If you have a network hardware lock, only one lock is used for all computers on the network. See below for details.) You need the hardware lock in order for Autohydro or Modelmaker to run in normal operating mode. Otherwise, the program will only run in demo mode. Keep the lock in a safe place when not in use. As outlined in the Licensing Agreement, you are exclusively responsible for the hardware lock. You may be required to purchase an additional software license if the hardware lock is lost or stolen. Precautions Before beginning the installation, close all running programs. Only network locks may be daisy-chained. For a local station installation, a single lock may be configured for all the programs the user is authorized to use. Certain local printers may interfere with the operation of the lock. If this is the case, try a different printer driver, or install another parallel port. On some laptop computers it may be neccessary to enter the System BIOS and permanently enable parallel port.

Hardware Lock Installation

Windows 95, Local Station

1. Plug the hardware lock into the parallel port. 2. If you had a printer connected to the same parallel port, plug the printer into the other end of the lock. 3. Install Autohydro as discussed above.

Windows NT, Local Station

1. If the Autohydro installation program detects a Windows NT operating system, you will be prompted: "Would you like to copy the NT lock driver files to your computer?" You must respond "Yes", unless you have previously installed the lock driver. (The NT lock driver is required so your operating system can communicate with the parallel port.) You will then be asked where you want to copy the NT lock driver files to. 2. The Autohydro installation program will indicate a Readme.wri file which contains instructions on how to run the NT lock driver installation program and will then terminate to allow you to run the lock driver installation. 3. Follow the instructions contained in the Readme.wri file to install the NT lock driver. 4. Re-start the Autohydro installation. This time, when the installation program asks if you would like the NT lock driver files copied to your computer, respond "No". 5. Follow the instructions to complete the installation of Autohydro onto your computer.

Chapter 1

Hardware Lock Installation, Network System

If you have purchased a network lock, you will have received a separate floppy named "Network Lock Driver". 1. Connect the network lock onto the parallel port on any one of the computers in your network. 2. The Network Lock Driver floppy contains 3 directories: \DOS (for Windows 3.11) \NW (for NetWare) \Win32 (for Windows 95 and Windows NT) Each directory contains a readme.txt file. Follow the directions appropriate for your operating system. 3. Install Autohydro onto each station on your network from which it will be run, following the installation instructions above.

Hardware Lock Installation

Starting and Exiting Autohydro

To start Autohydro, go to Start - Programs - Autoship and click the Autohydro shortcut. To start Modelmaker, go to Start - Programs - Autoship and click the Modelmaker shortcut. To start Print Parts, go to Start - Programs - Autoship and click the Print Parts shortcut. The fastest way to get going with Autohydro is to follow our "Quick Sailthrough" (chapter 3, this manual), and then to work your way through the tutorials starting in chapter 4 of this manual. For advanced and complex projects, you should take an Autohydro training course. Contact Autoship Systems, or your Autoship dealer for schedules and locations of upcoming courses, or for customised training.

Updating Autohydro
When you update Autohydro, the installation procedure is the same as for a new installation. All necessary program files are updated. No data you have saved will be adversely affected by updating the installation.

Hardware Lock Installation

10

About the Program

Chapter 2
About the Program
Introduction
Chapter 2 introduces the Autohydro and Modelmaker modules. It discusses how the programs work and how to operate them. Since key concepts and terminology are discussed, it is important that new users read this section.

11

Chapter 2

How Autohydro Works

Parts of the Program The Autohydro program is composed of three modules: Modelmaker Autohydro GF Print This manual focuses on the first two modules, Modelmaker and Autohydro. Modelmaker is used to create and edit the vessel models. Autohydro uses the model produced in Modelmaker to calculate the hydrostatic characteristics of the vessel. Each program module has its own sets screens, functions and commands. A vessel model, or Geometry File (GF) is merely a collection of groups of 2D cross sections, and their associated attributes, which define the entire model. Each group or "part" describes a particular piece of the vessel model, such as the hull or a compartment. In both Modelmaker and Autohydro you can work using pull-down menus and/or commands. Simple modelling and calculations by using the menus is demonstrated in the guided tour ("A Quick Sailthrough") provided in this manual while the full set of menus and commands is described in the Reference Manual.

Modelmaker Modelmaker is used to create and edit the vessel model. The main screen displays the model graphically and also shows the co-ordinates of the vertices that make up the model. Various tools allow you to create and edit the parts and components which define the model. A model is created by defining parts and their constituent components. A part is best thought of as an individual entity which you will want to work with seperately

12

How Autohydro Works

in Autohydro. For instance, you would likely model each fuel tank as a part, but would not group all the fuel tanks under one part. The part takes on attributes such as a name, side factor (Center, Port or Starboard), class (Displacer, Container or Sail), contents and specific gravity. Any number of parts can be created, but one of them must be named Hull. Without a part called Hull Autohydro cannot process the GF. Next, for each part, you define the physical shape, or volume, of the part by creating a component, or group of components, and assign further attributes, such as side designation and permeability. Modelmaker supplies several given basic forms, e.g., Box, Cylinder, etc. for which you define the extents to build your model. The shape of the component may be modified graphically, or by editing it's actual co-ordinates. One component may be joined to another component within the part to form a single, complex volume. You can also fit, or trim, components with each other. By repeating this process of creating, shaping, joining and fitting you end up with a complete model of the vessel.

Autohydro Using the model created in Modelmaker, Autohydro calculates various hydrostatic values for given conditions. The vessel's current situation is shown graphically in three different views on the screen, and also as text and values in the "Hydrostatics" window. You can analyse the model in three distinct ways, or modes: Given draft, trim and heel weight(s) waterline(s) You Can Find weight, center of gravity draft, trim, heel vessel characteristics

Autohydro is run by issuing commands, either by selecting them from a menu, typing them in or "running" a file containing commands. Putting together the appropriate sets of instructions allows you to analyse the model in several different conditions.

13

Chapter 2 Various reports describing the characteristics or stability of the vessel are available by using the appropriate pull down menu or command. By assembling the reports in the right order, you can produce a stability book. Commands Both Modelmaker and Autohydro can be controlled either by using pull down menus or by commands (instructions) issued by the user. In Modelmaker, commands can be grouped together using the program's text editor and saved as a "COMMAND" (.CMD) file. The command file is then run as a batch file and used to the create vessel model. Using commands is a convenient technique for modelling vessels because you can easily change the configuration of the model or correct mistakes just by editing the command file and re-running it instead of re-creating the model detail by detail as in the interactive (pull-down menu) mode. Often the best approach to create a model uses a mixture of the two methods. A command file is also useful when tasks are repeated. For example, when you have to model similar tanks, one tank definition can be copied, pasted and edited to create others. In Autohydro, you can either group commands as a "RUN" file using the program's text editor, or type individual commands on the command line on the main screen. When run, the RUN file simply instructs Autohydro to perform a certain set of calculations upon the currently loaded vessel model. Often a mixture of single commands and running a .RUN file is the best approach to accomplish a given task.

14

Key Concepts and Terms

Key Concepts and Terms

File Types
In addition to Geometry files, each program uses other special file formats: Modelmaker .CMD (Command): used to create and edit the vessel model. Autohydro .CD (Condition): information for a vessel loading condition. .CRI (Criterion): stability criteria to be used for stability assessment. .LIB (Library): of user-defined macro commands. .RUN (Run): a set of commands that Autohydro uses to set conditions and perform calculations. .SAV (Save): geometry file and information to reconstruct the loading, criteria, and settings currently in effect.

Geometry Files A GF (Geometry File) contains all the information about the geometry of the vessel, represented in detail appropriate for hydrostatic calculations. It describes the volumes of the hull and various compartments, their permeabily and the contents and specific gravity they hold, or displace. Each volume to be modeled consists of a series of transverse sections, arranged in order from bow to stern. By adjusting the permeability, deductions, such as reducing the hull volume to compenstate for

15

Chapter 2 a bow thruster, can be made. Additionally, volumes which are not considered watertight, but are to be used to for wind calculations can be defined. Modelmaker and Autohydro will read any GF, including those produced by Autoship as well as those created by GHS and BHS. Data Hierarchy The GF uses a hierarchical data structure which is broken down into: i. Parts ii. Components iii. Shapes Each part is made up of one or more components and each component is made up of a shape. For instance, the hull normally consists of one part having several components, such as the hull, keel, appendages and superstructure,. This is how the GFs data structure is arranged:
Data Element Part Information Contained
A NAME TAG FOR AN ENTITY

Component

Shape

nam e (includes side designator, .P, .S or .C) class (Displacer, Container, Sail) co-ordinates of the reference point containers only: substance (fluid contents and specific gravity) sounding tube definition references one or more components the volume information nam e (may include side designator) perm eability factor (negative = deducting) shift vector references a shape the geometrical description nam e x, y, z offsets of the com ponent

16

Key Concepts and Terms

There are two special considerations regarding GFs: 1. Every model has to have a part called HULL. 2. Every component must be attached to a part. Part Each part is identified by a name that must be unique within the model. The name also has a side designator: .C for centerline, .P for port, or .S for starboard. Each part is assigned a Contents which has a name and a specific gravity, i.e., Salt Water, 1.025. A part has a class designation: Displacer, Container or Sail. Displacers displace the fluid "contents", Containers contain the fluid "contents", a Sail part only produces an area for Wind heeling moments - it does not displace or contain a fluid. The part also has a Reference Point - a location that may be used as a reference when loading the tank, or as the spilling point when the tank type is set to Spilling. Tanks may also have a sounding tube definition. Note that a part is only a name tag with attributes and it must reference one or more components to comprise a volume. While Modelmaker can deal with parts, components and shapes, Autohydro can only access the model at the part level. Therefore, it is important that you define all the volumes you wish to work with, and to group them in a logical fashion. Component Each component is identified by a name and side designator that must be unique within the referencing part. Each component has an "effectiveness" - i.e. permeability. By default, displacers are assigned 1, containers are assigned .985. Components that are deducted from a part have a negative effectiveness. The component refers to one shape by name and gives the shape a specific location on the vessel by means of the shift vector, which by default is 0,0,0.

17

Chapter 2 Shape The shape is identified by a name, which is unique within the model. It represents a volume in space by a series of 2-dimensional cross sections. Each section is defined by a longitudinal position and a series of transverse and vertical co-ordinates. The shape has a definite size and orientation but its location is subject to modification by the referencing component. Note: Normally, you do not have to deal with shapes because they are treated by the program as the characteristics of a component. Stations and Points You will see each component on the screen as a series of 2-dimensional transverse sections. Each station has points located on its perimeter. You can change the shape of a station by modifying the positions of the points. Co-ordinate System A right-hand co-ordinate system is used. It is aligned with the principal axes of the vessel as follows: Origin: The point at which all three of the model axes cross, (the coordinates = 0, 0, 0). It can be located at any position along the center plane of the vessel, such as the AP at Baseline, FP at waterline or midships at underside of keel. The first piece of information you give to describe the model ultimately establishes the origin, however the origin can be moved at any later time. L-axis: The longitudinal, or X axis runs along the length of the vessel. Positive is aft of the origin, negative is forward. The program also recognises A for aft and F for forward. The model may be positioned anywhere longitudinally.

18

Key Concepts and Terms

T-axis: The transverse, or Y axis runs across the vessel. The transverse origin is the centerline of the vessel. It is positive to starboard and negative to port. The program also recognises S for starboard and P for port. Any Centerline (.C) components will be automatically mirrored across the centerline. Z-axis: The vertical, or Z axis is perpendicular to the vessel's baseplane (Z=0). Positive is above the baseplane and negative is below. The model may be positioned anywhere vertically. Units Lengths must be supplied either in decimal feet or meters. Switching from one set of units to another automatically converts the values in the model. The standard units of measurement used in Modelmaker and Autohydro are:
Measurement Length Weight/Displacement Volume Metric Units m MT m
3

Imperial Units ft LT ft3

Weight and displacement can also be expressed in Kilograms (KG), Short Tons (ST) and Kilopounds (KP). For more information, see the UNITS command in the Reference manual. Using Files from GHS/BHS Most files from GHS or BHS (from Creative Systems Inc.) may be used interchangeably with Autohydro and Modelmaker: GHS GF's can be read directly by Autohydro or Modelmaker. GHS Condition files, Criterion files, and Macro files can usually be read directly by Autohydro.

19

Chapter 2 GHS .RUN files can be read directly by Autohydro. Partmaker .RUN files can be read directly by Modelmaker if you rename .RUN to .CMD. Autohydro and Modelmaker cannot read GHS .SAV files or any other files that represent the environment settings. Some GHS and Partmaker commands are not essential to Autohydro or Modelmaker but do not affect operation. These non-essential commands are ignored.

Typical Job Flow

An Autohydro project usually proceeds through three steps: 1. Create a hull using one, or a combination, of these methods: Modelmaker menus A Modelmaker command file Digitising offsets in Modelmaker Export a GF from Autoship 2. Create internals such as tanks and sounding tubes using Modelmaker. 3. Create appendages such as derricks etc. using Modelmaker. 4. Perform analyses of the model's hydrostatic characteristics using Autohydro.

20

A Quick Sailthrough of Autohydro

Chapter 3
A Quick Sailthrough of Autohydro
Introduction
This chapter presents a quick tour of Autohydro. This is what we will do: Objectives i) To use Modelmaker to build a simple barge (40m x 10m x 5m) with forward and aft rakes (.5m headlog at fwd and aft ends, sloping to the bottom 5m from each end). ii) To use Autohydro to obtain lightship weight from given drafts and the operating draft for a load condition with deck cargo.

21

Chapter 3

Modelmaker
Preview of Tasks Modelmaker
Start Modelmaker Create a hull part Create component 1 Shape component 1 Create shaped component 2 Join components Save the file

Autohydro Start Autohydro and find lightship displacement Add deck cargo and find resultant drafts Generate and print a report Our co-ordinates will originate from: Longitudinal "0" at midships Transverse "0" at center line Vertical "0" at the lowest point on the flat bottom midships. Remember the data hierarchy: you will make and edit model elements in the following order: Part Component Shape

22

Modelmaker

Start Modelmaker
Click the Modelmaker icon in the Autoship group/folder. When Modelmaker finishes starting, pick File - New GF. In the dialogue that appears, type a file name, MYBARGE.GF1 for instance, specify a directory to store it in, then Click OK. Note: Make a note of the filename and the directory where you are storing the file.

Create a Part
On the top menu bar, click Options and select Meters. From the Edit menu select the Part Create/Edit option. In the dialogue that appears, under Part Name you will see NEWPART highlighted. Type HULL over it (it does not matter whether you type in upper or lower case). Note: You must have a part named HULL. If you don't, the model won't work in Autohydro. For Side, click the Center radio button. For Class, click the Displacer radio button. Click OK. Now, back at the main screen, nothing shows because there are no components to display yet.

Create Component 1
We will create the hull as a combination of two box-shaped components. The first component will be the parallel midship section including the aft rake, and we will shape it to form the aft rake. The second component will be the forward rake and, to demonstrate different techniques, we will shape it using a different method. We will then join them together to make a single component.

23

Chapter 3 1. From the Edit menu, select the Component Create function. In the dialogue that appears, you will see HULL on the left hand side. If it is not already highlighted, then click it to highlight it. On the right hand side you will see a list of the basic component shapes, called "primitives", that Modelmaker uses as building blocks. 2. Click the Box radio button and then click Input. 3. The Create Box dialogue will appear. Under Component Name you will see C1. 4. Click the FWD End input box and type 15f (it will show as 15.000f). 5. Click the AFT End input box and type 20a 6. Click the Station Spacing input box and type 2.5 to specify the space between adjacent stations. Note: Later, if you find this station spacing too large for fitting parts and components together smoothly, you can change the spacing by adding more stations with the Fill command in the Edit menu. 7. To the right of OUTBOARD, in the TRANS input box, type 5 to set the halfbreadth. 8. To the right of TOP, in the VERT input box, type 5 to set the height of the deck above baseline. 9. In the Side Factor box click Center. 10. Click OK. 11. In the Create Component dialogue, click Done to return to the main screen. 12. A rectangle will now appear on the screen. 13. Choose Iso (Isometric) from the View menu. This will display the first compo nent of the model showing all the stations, with the currently selected station

24

Modelmaker

(the forward-most one) highlighted in black and the red cross-shaped cursor highlighting the first vertex of the station.

Shape Component 1
1. We will shape the first component in this way: 2. Shift through the group of stations from the forward-most station to the aft-most by pressing F6 until the aft-most station is highlighted. "Location" near the bottom left of the screen will read 20a. 3. The cursor will show at the bottom-center of the station highlighting the first vertex of the station. We will change the shape of this section by moving the two bottom vertices upwards to the height of the lower edge of the headlog. To do this, press the up arrow on the keyboard repeatedly until the 1st "Vert" cell under Edit Points at the left of the screen reads 4.5. 4. Shift the cursor to the next vertex on the station by pressing F4. 5. Move the cursor up with the up arrow key until the 2nd Vert cell under Edit Points reads 4.5. Hit Enter to update the changes and redraw the view. 6. Shift to the next station forward by pressing F5. 7. Shape this station differently (just for practice): type 2.25 in the 1st Vert cell and 2.25 in the 2nd Vert cell and hit Enter to update the changes and redraw the view. Note: If at any time the screen does not show changes that you have made, click the Redraw button. Now we will create the second component.

25

Chapter 3

Create Shaped Component 2

Modelmaker allows you to specify a sloped top, bottom, inboard or outboard face for a "box" shape. We will use this feature to create the sloped forward rake. 1. From the Edit menu select the Component Create option. In the Create Component dialogue click HULL, on Box and then on Input. 2. In the Create Box dialogue you will see C2 for the name of this component. Type these values: FWD End 20f AFT End 15f Station Spacing 2.5 Outboard Trans 5 Top Vert 5 3. Click the SLOPING? checkbox for Bottom. This will open up three additional input boxes. Input the following values: Vert 4.5 Long 20f Vert 0 Long 15f 4. Make sure that Side Factor is set to Center and then Click OK. Click Done. If the main screen shows no change, select View Part from the View menu to see the entire part. Note: To scroll through the components of the model, use the space bar.

26

Modelmaker

Join Components
We will now join the two components for a cleaner appearance. Note: whether a part is made of one component or several, there will be no difference in the resultant calculations in Autohydro. 1. Select View - View Profile to see the entire model in profile. 2. From the Edit menu choose Join To. The Join dialogue will appear. Under Join Component, pick HULL for part and C2 for component. 3. Under Component To Join To, pick HULL for part and C1 for component. 4. Click OK. 5. You will see your complete model without any break between components. 6. Note that all reference to the component C2 is gone - it has been amalgamated with component C1.

Save the File 1. Choose Save from the File menu.

27

Chapter 3

Autohydro
Start Autohydro and Find Lightship Displacement
Start Autohydro by clicking on the Autohydro icon in the Autoship group/folder. When Autohydro has finished starting, click File - Open, select the GF you just created and Click OK. When the GF is finished loading you should see a representation of your barge. One of the main ways Autohydro can be used is to have it find the displacement and LCG for a given waterline, and assign that displacement and LCG to the lightship weight. We will input two drafts to define a waterline and then use this method to determine the lightship weight: 1. Suppose the lightship drafts are: 1.34m aft (at the forward end of the aft rake, at 15a); and 1.26m fwd (at the aft the of the forward rake, at 15f) 2. Input these drafts into Autohydro by typing on the command line: DRAFT 1.34 @ 15a, 1.26 @ 15f <Enter> Note: the comma is optional and it does not matter whether you type in upper case or lower case. 3. Now let's get Autohydro to find the displacement and longitudinal center of gravity (LCG) corresponding to these drafts. On the command line, type: SOLVE WEIGHT LCG <Enter> 4. In the Hydrostatic Values window you should now see the following results: (your Hydrostatic Value window may show different values)
28

Autohydro

Draft status: Aft = 1.35 Mid = 1.30 Fwd = 1.25 m Lightship: 419.0 MT FLCG: .194a (Fixed weight LCG)

Note that the drafts shown are not the drafts you put in. The drafts reported are being measured at the extreme ends of the vessel, while the drafts you input were located closer to midships. 5. To reset the locations where the drafts are measured, so they match your draft mark locations, typing on the command line: DRAFT "US KEEL" 0 @ 15a, 0 @ 15f <Enter> 6. Now we know the lightship weight and its LCG. By default, both the transverse and vertical center of gravity are zero. 7. Assuming we had calculated the vertical center of gravity to be 3.2m above baseline, we can input this value with the command: VCG 3.2 <Enter> 8. You may have noticed that when you entered this last command the Solve button in the top left corner of the screen changed from grey to red. The solve button is grey when the vessel in equilibrium and red when the vessel is not in equilibrium. In this case, changing the VCG caused the vessel to go out of equilibrium. To Autohydro, the vessel is in equilibrium when three conditions are met: displacement = the total of all weights (lightship + added weights + tank loads) LCB = trimmed LCG (RAt = 0) TCB = heeled TCG (RAh = 0)

29

Chapter 3 To get Autohydro to calculate a new equilibrium, click the Solve button. After a quick calculation, the Solve button will turn grey, the graphics window showing the model will be updated and the Hydrostatics Values window will show new values. At this point, Autohydro has a model to work with, has a reference line for measuring the drafts and knows the vessel's lightship weight and center of gravity. Now we can add some deck cargo and find the new drafts.

Add Deck Cargo and Find Resultant Drafts

Autohydro maintains two weight categories. One has further sub-categories: 1. Fixed Weight: i) Lightship Weight can be set: with the WEIGHT command, or by specifying drafts or depth and using the SOLVE WEIGHT command. ii) Added Weights can be input: with the ADD command, or in a dialogue box accessed from the Weight button. 2. Tank Loads can be specified: with the LOAD command, or in a dialogue box accessed from the Tank Loads button.

30

Autohydro

In our barge model we will add two fixed weight items as deck cargo. (If we had defined some tanks in the model, we could have loaded them with some contents, thus adding liquid weight.) 1. To add a fixed weight item, click the Fixed Weight button. In the Weight List dialogue that comes up, click Add and change the label New Weight Item#01 to Lumber on deck, set its LCG to 12a, VCG to 6.5, and Weight to 3. 2. To add the second fixed weight item, click Add, change New Weight Item#01 to Forklift on deck, set its LCG to 10f, VCG to 6.1, and Weight to 1.3. 3. Close the dialogue box by clicking on OK and return to the main Autohydro screen. 4. Because some variables have been changed the vessel will be out of equilibrium. However, when you exit the Added Weights dialogue, Autohydro will automatically find the new equilibrium. Now we know the total weight and center of gravity of the vessel and cargo, and the resultant drafts. All we need now is to create a report of this condition and print it out.

Generate and Print a Report

Autohydro has different commands to produce different outputs. The most commonly used (and most general) is Status, which creates an overall status report of the current loading condition. 1. To generate a report, on the command line, type: STATUS, then click Enter. 2. If the Output window is open, it will be filled with an unformatted report. 3. To see the formatted report, click the Report button.

31

Chapter 3 You can resize the Report window (like all other windows in Autohydro). It also has scroll bars to move around on the page. Since the Report window is a text editor, you can edit your report right here in Autohydro, or write out a file that can be read directly by Word and then sent to Excel. To print the report, choose Print from the File menu, or click the Printer button.

Summary
You have used Modelmaker to create and edit a vessel model. You have used Autohydro to calculate hydrostatic behaviour of the model. You have produced a report of the vessel

32

Tutorials

Chapter 4
Tutorials
Introduction
This chapter includes seven tutorials. It is suggested that you work through each tutorial in the sequence presented, as each subsequent tutorial depends upon knowledge gained in the previous one. The tutorials are: Tutorial 1: Modelmaker project using menus and screens Tutorial 2: Running Autohydro using menus and screens Tutorial 3: Modelmaker project using command files Tutorial 4: Autohydro using commands Tutorial 5: Modeling a vessel using Modelmaker commands Tutorial 6: How to produce a stability book in Autohydro Tutorial 7: How to assess damage stability in Autohydro

33

Chapter 4

Tutorial 1
Modelmaker Project Using Menus and Screens
The learning objectives here are: to create parts by fitting them to other parts. to create a tank part with a recessed portion by joining a number of components together. to create a tank part with a recessed portion by fitting to it a temporary part and then deleting the temporary part.

Add Tanks to the Barge Created in the Quick Sailthrough.

We will create 6 tanks: Two void tanks (a Forepeak and an Aftpeak) plus four cargo tanks in between, two having a recess on top. 1. Load MYBARGE.GF1 (or the name you used for your geometry file) as cre ated in the Autohydro Sailthrough. Note: Click View - ISO to get the best viewing angle. 2. Start by adding more stations to the model so that Modelmaker can fit parts together smoothly. From the Edit menu choose Fill In the Fill station dialogue, in the Maximum Station Spacing field, type .5, and click OK. This will fill the HULL with more stations and ensure smooth fits.

34

Tutorial 1

3. Create the fwd tank: Part: (Edit - Part Create/Edit and then Add) Part name: Side: Class: Contents: FOREPEAK Center Container SEA WATER

Component: (Edit - Component Create, select FOREPEAK, Click the Box radio button and thenthe Input button). FWD: AFT: Station spacing: Outboard Trans: Top Vert: Bottom Vert: 21f 14.5f Match Stations to Hull 6 6 1

Note: Observe that the dimensions extend beyond the hull. To get Modelmaker to fit, or trim, parts properly, you must specify slightly larger dimensions for the part that is to be fitted to another part. 4. Fit FOREPEAK to HULL: From the Edit menu choose Fit to. In the Fit Component dialogue, under Fit Component, for Part Name choose FOREPEAK and the appropriate component. Under Part or Component to Fit To, for Part Name choose HULL and the appropriate component. Under Type of Fit choose Internal. Click OK.

35

Chapter 4 5. Create the aft tank: Part: Part name: Side: Class: Contents: Component: (Box) FWD: AFT: Station spacing: Outboard Trans: Top Vert: Bottom Vert: 6. Fit AFTPEAK to HULL: From the Edit menu choose Fit to. In the Fit Component dialogue, under Fit Component, for Part Name choose AFTPEAK. Under Part or Component to Fit To, for Part Name choose HULL. Under Type of Fit choose Internal. Click OK. We have now created and fit two simple tanks. The next two tanks are more complicated in shape as they have a well, or recess in the top. We will construct the next tank out of several "boxes" and then join them together. 7. Create a port tank aft of midships, out of 3 components: Part: Part name: Side: Class: Contents:
36

AFTPEAK Center Container Seawater

14.5a 21a Match Stations to Hull 6 6 -1

NO1 Port Container Diesel oil

Tutorial 1

Component: (Box) FWD: AFT: Station spacing: Outboard Trans: Top Vert: Bottom Vert: 5a 4.5a Match Stations to Hull 6 6 -1

Component, for the second of the 3 components: (Box) FWD: AFT: Station spacing: Inboard Trans: Otboard Trans: Top Vert: Bottom Vert: 0 5a Match Stations to Hull 2 6 6 -1

Component, for the third of the 3 components: (Box) FWD: AFT: Station spacing: Outboard Trans: Top Vert: Bottom Vert: 0 5a Match Stations to Hull 3 3 -1

Join the third component to the second component: Click Edit - Join To. Under Join Component, for Part Name pick NO1.P, for Comp Name pick C3. Under Component to Join to, for Part Name pick NO1.P, for Comp Name pick C2. Click OK.

37

Chapter 4 Join the second component to the first component in the same manner. Now you have a tank with a recess in the top. 8. Fit NO1.P to HULL: From the Edit menu choose Fit to. In the Fit Component dialogue, under Fit Component, for Part Name choose NO1.P and the appropriate component. Under Part or Component to Fit To, for Part Name choose HULL and the appropriate component. Under Type of Fit choose Internal. Click OK. 9. Create a starboard tank aft of midships, matching the NO1.P tank We will create this tank in a different way. We will start by creating a regular rectangular shape. Next, we will create a temporary smaller rectangular shape. Then we will fit the larger one to the smaller one. Finally, we will delete the temporary part. Note that the class and contents of the temporay part do not matter because we are only interested in the shape, and only on a temporay basis. Part: (the tank part) Part name: Side: Class: Contents: Component: (Box) FWD: AFT: Station spacing: Outboard Trans: Top Vert: Bottom Vert:
38

NO1 Starboard Container Diesel oil

0 14.5a Match Stations to Hull 6 6 -1

Tutorial 1

Part: (the temporary part) Part name: Side: Temp Starboard

Component: (Box) FWD: AFT: Station spacing: Inboard Trans: Outboard Trans: T op Vert: Bottom Vert: 0 5a Match Stations to Hull 1 2 7 3

10. Fit NO1.S against the part called Temp: From the Edit menu choose Fit to. In the Fit Component dialogue, under Fit Component, for Part Name choose NO1.S. Under Part or Component to Fit To, for Part Name choose TEMP. Under Type of Fit choose External. Click OK. 11. Fit NO1.S to HULL: From the Edit menu choose Fit to. In the Fit Component dialogue, under Fit Component, for Part Name choose NO1.S Under Part or Component to Fit To, for Part Name choose HULL Under Type of Fit choose Internal. Click OK.

39

Chapter 4 12. Delete the temporary Part: Go to Edit - Delete Part/Component, pick TEMP.S and Click the Delete Part/Comps button. Click 'Yes' at the message "Delete part TEMP.S" and then Click Close. That finishes the two tanks with the recesses in the top. 13. Create a port tank fwd of midships: Part: Part name: Side: Class: Contents: Component: (Box) FWD: AFT: Station spacing: Outboard Trans Top Vert: Bottom Vert 14.5f 0 Match Stations to Hull 6 6 1 NO2 Port Container Gasoline

14. Fit NO2.P to HULL: From the Edit menu choose Fit to. In the Fit Component dialogue, under Fit Component, for Part Name choose NO2.P. Under Part or Component to Fit To, for Part Name choose HULL. Under Type of Fit choose Internal. Click OK.

40

Tutorial 1

15. Create the opposite part, NO2.S: In the Edit menu, click Opposite part. In the Opposite Part dialogue choose NO2.P from the first. The second field will show NO2.S. Click OK. Now your barge is fitted with all six tanks.

Create Sounding Tubes for the Cargo Tanks

1. Set up the sounding tubes: In the edit menu, click Sounding Tube. In the Sounding Tube dialogue, choose the tank to have the sounding tube; start with NO1.P. Click Insert points twice. In the grid, type in the following values for points 1 and 2. Point 1 must be the lowest point on the tube. Be sure to click Record to register the changes. Pt. 1 Pt. 2 Long .2a .2a Trans 4.8p 4.8p Vert .005 5.25

2. Create sounding tubes for the other tanks in the same way. Remember to designate aft or forward, and port or starboard.

41

Chapter 4

Create a Deckhouse
1. Create a deckhouse with the following dimensions: length: 5m - fwd end at 14a, aft end at 19a height: from the deck to 2.5m above deck, width: 3m wide - inboard at 2.5m from centerline, the outboard side overhangs the starboard side of the hull by .5m. Part: Part name: Side: Class: Component: (Box) AFT FWD: Station spacing: Inboard Trans: Outboard Trans: Top Vert: Bottom Vert 19a 14a Match Stations to Hull 2.5 5.5 7.5 5 Deckhouse Starboard Sail

The modifications to the model are now finished. Save your model. To avoid overwriting your original model, use a different name; we suggest incrementing the extension, i.e., if you named the original barge MYBARGE.GF1, name this model MYBARGE.GF2.

42

Tutorial 2

Tutorial 2
Running Autohydro Using Menus and Screens
Find Hydrostatics, Cross-Curves and Hull Data
1. In Autohydro, Open MYBARGE.GF2 (or the name you used for your geometry file). 2. From the Calculate menu, choose Hydrostatics and in the Drafts dialogue, enter the following values and Click OK: First .5 Last 4.5 Step .5 Autohydro will show the calculation results in the output window. As well, they will be available in the report window. 3. From the Calculate menu, choose Cross curves and in the Drafts dialogue, enter the following values and Click OK: First .5 Last 4.5 Step .5 Autohydro will show the calculation results in the output window. As well, they will be available in the report window.

43

Chapter 4 Type the following three commands on the command line. Remember to hit Enter after each command: HEEL 0 TRIM 0 DEPTH 2 4. From the Calculate menu, choose Hull data. In the Hull Characteristics dialogue click the Hull Data radio button and then on OK. Autohydro will show the calculation results in the output window. As well, they will be available in the report window. Note that you could have specified different values for Heel, Trim and Depth.

Find Drafts for a Given Weight and Center of Gravity

1. On the Command line, type <weight 100 .25a 0 3.6>. Weight is a command telling Autohydro to set the lightship weight and center to the values that follow; the first value is the weight, the second is the lcg, the third is tcg, and the fourth is the vcg. Note that the lcg, tcg and vcg are optional, but they will remain at the default, 0, until changed by some other method. Weight Autohydro maintains two weight categories, for use in calculations: i. Fixed weight ii. Liquid weight Fixed Weight There are two kinds of fixed weight: i. lightship weight: this is set with the WEIGHT command, or found with the SOLVE WEIGHT command. ii. the weight of all other fixed items, as set with the ADD command.

44

Tutorial 2

Liquid Weight The volume of contents in a tank is set either with the LOAD command or in the Tank Contents window. You can set the load either by load fraction, or by weight, or, if sounding tubes are defined, by sounding. Setting or changing one of these will update the others in a given tank. You can also change the tank contents by using the CONTENTS command, or by right-clicking on the tank in one of the views, picking the Tank Contents option and selecting a fluid from the list. 2. Load tanks: Click the tank window and set the loads of some of the tanks. Click the Solve button when you are done to find the new equilibrium. 3. On the command line, type STATUS to generate a report of the current loading scheme and resultant vessel attitude. View the results in the report window. 4. One the command line, type RA to generate a righting arm curve for the current loading scheme. View the results in the report window.

45

Chapter 4

Tutorial 3
Modelmaker Project Using Command Files
The learning objectives here are: to use Modelmaker's text editor to write a .CMD file (a series of commands). to run the commands to produce a vessel model.

Create a Barge, LOLLIPOP.GF1

We will create a barge which has a deckhouse and two deck-mounted cylindrical diesel oil tanks. The hull dimensions are 40m long, 10m wide, 5m deep, with forward and aft rakes sloping from 15f and 15a, respectively, to .5m below deck. 1. Click CMD on the menu bar. A text editor will appear. If the text editor window is not empty, then click the Files - New menu option to clear the editor. Click any where in the editor window and type the command CLEAR. The CLEAR command removes any existing geometry from Modelmaker's memory. Note: Modelmaker cannot create a new part if a part with the same name already exists. Therefore, when re-running a .CMD file it is important to remove the previously created set of parts before creating new ones. Below the CLEAR command, type the following, pressing ENTER after every line. An explanation of each command follows in italics do not type this part.

46

Tutorial 3

units mt create hull.c spacing .5 ends 15f 15a top 5 bottom 0 outboard 5 component fwdrake ends 20f 15f top 5 bottom 0 @ 15f 4.5 @ 20f outboard 5 join hull.c component aftrake ends 15a 20a top 5 bottom 0 @ 15a 4.5 @ 20a outboard 5 join hull.c / create deckhouse.c class sail ends 14a 17.5a top 8 bottom 5 outboard 1.5c / create cargo.s contents do cylinder 6f 2.4 8.5 7a 2.4 8.5 3.2 3.2 /

set units to meters and tonnes start description of part "hull.c" set station spacing at .5m intervals define two ends of a box-like component define the top of the box define the bottom of the box define the outboard face of the box describe another component for hull define the two ends of another box define the top of this box define a sloping bottom define the outboard face of this box join this component to "hull.c" describe another component of "hull.c" define the top of this box define the top of this box define a sloping bottom define the outboard face of this box join this component to hull.c end description of part "hull.c" start description of part "deckhouse.c" set to sail rather than container define two ends of a box-like component define the top of the box define the bottom of the box define the outboard face of the box end description of part "deckhouse.c" start description of part "cargo.s" set the contents to diesel oil define as a cylinder end description of part "cargo.s"

47

Chapter 4
create cargo.p contents do opposite cargo.s write c:\autoship\hydro\samples\loll pop.gf1 start description of part "cargo.p" set the contents to diesel oil copy and mirror shape of "cargo.s save the geometry

Check that the path, as specified in the last command, is valid for your computer. Note: A convenient way to write this series is simply to copy and paste similar instructions: you can copy the six lines for the forward rake (from "component fwdrake" to "join hull") and paste them as the next segment, for the aftrake. But remember to change "fwd" for "aft" and the co-ordinates from "f" to "a". 2. Still in the text editor, click Run, and choose Background. The text editor window will close and Modelmaker will begin processing the set of commands. 3. When processing has finished, from the View menu, choose whichever view you prefer and the View all option. You will see your model on the screen. If you don't, click Redraw in Shape editor box. You have now finished creating the barge that we will be used for Tutorial 4.

48

Tutorial 4

Tutorial 4
Running Autohydro Using Commands
The learning objective here is: to use Autohydro commands to perform simple calculations.

Obtain Basic Output from LOLLIPOP.GF1

1. Start Autohydro and click the Editor button. In the Text Editor that appears, type the following series of commands: read c:\autoship\hydro\samples\lollipop.gf1 ghs 2 3 4 cc 2 3 4 hull /dr 2 3 4 /da The "read" command must contain the same path as specified in the "write" command from the previous tutorial. 2. Click RUN and then Batch in the Text Editor top bar. Autohydro will calculate hydrostatic curves, cross curves and the hull characteristics at drafts of 2m, 3m and 4m and display the results in both the output window and the report window.

49

Chapter 4

Tutorial 5
Modelling a Vessel Using Modelmaker Commands
The learning objectives here are: to use Modelmaker's text editor to construct a command sequence to understand the operation of the locus command to save the command sequence as a .CMD file to run the .CMD file Note: The locus command allows you to define a station by specifying a longitudinal location and a set of transverse-vertical co-ordinate pairs. The locus command is particularly useful when you wish to create a GF from a table of offsets. Tip: An easy way to work with a table of offsets is to put the offsets into a spreadsheet. You can then simply cut and paste them into a command file.

Load a Command File

1. Open the Command File editor and load TUT5A.CMD from the \hydro\sample directory. Take a moment to look at the contents of the command file. You will see several "Locus" commands. In TUT5A.CMD, the exact offsets of a hull have been entered as LOCUS commands. 2. In the top bar of the text editor, click Run - Background. This will cause Modelmaker to execute the set of Locus commands and produce a hull.

50

Tutorial 5

Load a Second Command File

1. Load the command file TUT5B.CMD, replacing TUT5A.CMD currently in the text editor. This command file will create all the tanks for the hull just created. Note that the first two commands, Clear and Read, have the character "`" at the front of the line to "comment out" the command (not have it run). Normally, you would start your .CMD files with these two commands, however, because the model from TUT5A.CMD has not been saved, we have commented the commands out here. Note also the use of the Temp(orary) part and the command Delete at the end of the .CMD file to delete it. 2. In the top bar of the text editor, click Run, and choose Restart to create all the tanks. Click View - Iso and then View - View Part and then press repeatedly on the space bar to toggle through all the parts. 3. Save the completed GF file with a name and directory of your choice.

51

Chapter 4

Tutorial 6
How to Produce a Stability Book in Autohydro
The learning objectives here are: to construct a typical sequence of commands for intact stability analysis as follows: a) Set up limits b) Specify lightship weight (Alternatively, you can specify drafts) c) Repeat the following steps for each loading condition i. Set up the loading condition ii. Solve for equilibrium iii. Report the results

Load a RUN File

1. In Autohydro, click Open and load the GF file you just saved in Modelmaker. 2. Click the Editor button to open the run file editor. Load the file TUT6.RUN by clicking on File - Open and selecting the file from the ..\hydro\samples directory. Take a moment to review the contents of this file. It may be helpful to refer to the Reference Manual, or the On-line Help system, to understand what the various commands and parameters will accomplish and why they are used.

52

Tutorial 6

With this run file, we will: Set up limits Specify lightship weight [Alternatively, you could specify drafts.] Set up a load condition Solve for equilibrium. Report the results Clear the loads and added weights Set up a second loading condition Solve for equilibrium Report the results 3. Run the RUN file by clicking on Run in the top bar of the editor. Observe that a Stop sign appears in the top bar of Autohydro while the calculations are being carried out. When the top sign disappears, open the Report Window to show the results. You can either print them out, save them or discard them.

53

Chapter 4

Tutorial 7
How to Assess Damage Stability in Autohydro
The learning objectives here are: To construct a typical sequence of commands for damaged stability analysis. 1. To be sure that you will start with the program initialised correctly, click Open and reload the GF file you had saved in Modelmaker. 2. Click the Edit button to start the Run file editor. Load the file TUT7.RUN. With this file we will: Define limits Set up lightship Set up a loading condition Set up a damage condition Solve for equilibrium Report the results Clear the loads and added weights Set up a second damage condition Solve for equilibrium Report the results

54

Notes

55

Copyright 2004 Autoship Systems Corporation

Windows is a trademark of Microsoft Corporation AutoCAD is a trademark of Autodesk, Inc
TM