Scribd
Upload
31 views

High Pitched Horn Assy: Replacement

This document provides instructions for replacing the high pitched horn assembly on a Toyota Avensis. It describes: 1) Removing the old horn assembly by disconnecting the connector and removing the bolt and horn. 2) Installing the new horn assembly by placing the stay onto the radiator support, installing the horn with the bolt, and reconnecting the connector. The bolt should be torqued to 20 Nm. 3) Inspecting other horn components, including checking the operation and resistance of the low pitched horn, high pitched horn, and horn relay assemblies.

Uploaded by

Musat Catalin-Marian
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
31 views

High Pitched Horn Assy: Replacement

This document provides instructions for replacing the high pitched horn assembly on a Toyota Avensis. It describes: 1) Removing the old horn assembly by disconnecting the connector and removing the bolt and horn. 2) Installing the new horn assembly by placing the stay onto the radiator support, installing the horn with the bolt, and reconnecting the connector. The bolt should be torqued to 20 Nm. 3) Inspecting other horn components, including checking the operation and resistance of the low pitched horn, high pitched horn, and horn relay assemblies.

Uploaded by

Musat Catalin-Marian
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

695

COMMUNICATION SYSTEM HIGH PITCHED HORN ASSY

HIGH PITCHED HORN ASSY


6906702

REPLACEMENT
1. (a) (b) REMOVE HIGH PITCHED HORN ASSY Disconnect the connector. Remove the bolt and horn.

2. (a)

(b)

INSTALL HIGH PITCHED HORN ASSY Place the stay onto the baffle part in the radiator support upper, and then install the horn with the bolt. Torque: 20 NVm (204 kgfVcm, 15 ftVlbf) Connect the connector.

B67410

AVENSIS REPAIR MANUAL (RM1018E)

691
COMMUNICATION SYSTEM HORN SYSTEM

HORN SYSTEM
6906402

LOCATION
HORN Relay

High Pitched Horn Low Pitched Horn

Engine Room R/B No. 2

Engine Room R/B HORN Fuse

B67409

AVENSIS REPAIR MANUAL (RM1018E)

692
COMMUNICATION SYSTEM HORN SYSTEM
6906502

PROBLEM SYMPTOMS TABLE


Symptom 1. 2. 3. 4. 5. 6. Suspected Area Horn button switch High pitched horn Low pitched horn HORN fuse HORN relay Wire harness See Page 693 693 693

Horn does not sound

AVENSIS REPAIR MANUAL (RM1018E)

693
COMMUNICATION SYSTEM HORN SYSTEM
6906602

INSPECTION

1. (a)

INSPECT LOW PITCHED HORN ASSY Check operation of the horn. Standard:
MeasurementCondition Battery positive (+) Battery positive () Terminal 1 Horn body Specified Condition Horn sounds

If the result is not as specified, replace the horn assy.


B67416

2. (a)

INSPECT HIGH PITCHED HORN ASSY Check operation of the horn. Standard:
MeasurementCondition Battery positive (+) Battery positive () Terminal 1 Horn body Specified Condition Horn sounds

If the result is not as specified, replace the horn assy.


B67417

3. (a) (b)

INSPECT HORN RELAY ASSY Remove the HORN relay from the engine room R/B No. 2. Check the horn relay resistance. Standard:
Specified Condition 10 kW or higher Below 1 W (When battery voltage is applied to terminals 1 and 2)

Tester Connection

3
B68374

35

If the result is not as specified, replace the relay assy.

AVENSIS REPAIR MANUAL (RM1018E)

694
COMMUNICATION SYSTEM LOW PITCHED HORN ASSY

LOW PITCHED HORN ASSY


6906802

REPLACEMENT
1. (a) (b) REMOVE LOW PITCHED HORN ASSY Disconnect the connector. Remove the bolt and horn.

2. (a)

(b)

INSTALL LOW PITCHED HORN ASSY Place the stay onto the baffle part in the radiator support upper, and then install the horn with the bolt. Torque: 20 NVm (204 kgfVcm, 15 ftVlbf) Connect the connector.

B67411

AVENSIS REPAIR MANUAL (RM1018E)

You might also like