Scribd
Upload
6K views

CCNPv6 ROUTE SBA Skills-Based Assessment

This exam tests the ability to configure routers according to a topology diagram using static routes, EIGRP, OSPF, BGP, and RIPng. Students must configure interfaces, routing protocols, loopbacks, filtering, and an IPv6 tunnel to test IPv4 and IPv6 connectivity. The exam verifies that routing preferences, path selection, and failover routes work as intended.

Uploaded by

Brian Svendsen
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
6K views

CCNPv6 ROUTE SBA Skills-Based Assessment

This exam tests the ability to configure routers according to a topology diagram using static routes, EIGRP, OSPF, BGP, and RIPng. Students must configure interfaces, routing protocols, loopbacks, filtering, and an IPv6 tunnel to test IPv4 and IPv6 connectivity. The exam verifies that routing preferences, path selection, and failover routes work as intended.

Uploaded by

Brian Svendsen
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

CCNPv6 ROUTE

Skills-Based Assessment
Topology

Objectives
Configure the routers in the topology according to the diagram and the specifications provided.

Part 1: Configure the network according to specifications Part 2: Test network connectivity and path control.

Page 1 of 3

CCNPv6 ROUTE

Exam Overview
Configure static routes and multiple routing protocols, including EIGRP, OSPF and BGP to create an integrated network. Configure an IPv6 tunnel between R1 and R3 to use the RIPng protocol. Test IPv4 and IPv6 connectivity and use traceroute and show commands to verify routing and path selection. This exam combines device configuration and troubleshooting.

Part 1: Configure the network according to specifications.


1. Configure interfaces with the IP addresses shown in the diagram. Set the bandwidth to 128 kbps on the links between R1, R2, and R3 and set the clock rate on the all DCE connections to 128.000. Add a description for each WAN interface. 2. Configure the OSPF router identifier 2.2.2.2 on R2 and 3.3.3.3 on R3. 3. Ensure that all loopback interfaces are advertised in OSPF with the correct masks. Place the loopback interface Lo0 on R3 and the connection between R2 and R3 in OSPF area 0. 4. On R2, place the loopback interfaces Lo120 through Lo123 on R2 in OSPF area 1 and the connection between R2 and R3 in OSPF area 0. 5. Summarize area 1 to the backbone with the most efficient mask. 6. Propagate a default route from R3 into the OSPF domain. 7. Configure R1 to be in EIGRP AS 101, add the entire class C network, and disable automatic summarization. 8. Configure R2 to be in EIGRP AS 101, add only the link between R1 and R2 and disable automatic summarization. 9. Configure passive and non-passive interfaces for EIGRP and OSPF as appropriate. 10. Configure a static default route from R1 to R2 and avoid a recursive lookup. 11. Redistribute EIGRP into OSPF with a metric of 1000. 12. On R2, filter R1 network 192.168.113.0 from being advertised to R3. 13. Enable BGP on both WAN links between R3 and R4. R3 is in BGP AS 65101 and R4 is in BGP AS 65401. 14. Advertise R4s loopback interfaces into BGP. 15. Modify the local preference on R3 so that AS 65101 prefers the T1 link to AS 65401 networks. 16. Traffic exiting from R3 and returning to R3 should prefer the T1 link. Add a static route on R4 to 192.168.0.0/16 pointing to the T1 link to R3 and add a floating static route as a backup using the FT1 link. 17. Configure the IPv6 loopback and tunnel interfaces on R1 and R3. 18. Enable RIPng on R1 and R3 and configure the advertisement of the loopback and tunnel networks.

Page 2 of 3

CCNPv6 ROUTE

Part 2: Test network connectivity and path control.


Note: One or more addresses will not be reachable from all routers after final configuration due to the use of distribute lists to filter routes and the use of IPv4 and IPv6 addressing in the same network. a. Verify that filtered routes are not present in routing tables of the correct routers. b. Verify that traffic from AS 65101 to AS 65401 uses the preferred T1 route. c. Verify that R4 has a backup route to the AS 65101 networks if the T1 link fails.

d. Verify that R1 and R3 have learned of their respective IPv6 networks via RIPng. e. Verify that R1 can ping the R3 Lo3 interface via the IPv6 tunnel. R1 and R3 should also be able to ping the tunnel endpoints.

Page 3 of 3

You might also like