Scribd
Upload
84 views

Model Cutter: "Eee" Model Making Kit (2A & B)

The document describes a model making kit that includes a motorized fret saw and model polisher. The fret saw has a reciprocating blade that can cut templates from aluminum sheets. The model polisher can then polish and finish specimens cut on the fret saw to the required size using a high-speed cutting tool. Both machines have sturdy construction and are designed to accurately cut and polish modeling materials without vibration.

Uploaded by

Suniljpatil
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
84 views

Model Cutter: "Eee" Model Making Kit (2A & B)

The document describes a model making kit that includes a motorized fret saw and model polisher. The fret saw has a reciprocating blade that can cut templates from aluminum sheets. The model polisher can then polish and finish specimens cut on the fret saw to the required size using a high-speed cutting tool. Both machines have sturdy construction and are designed to accurately cut and polish modeling materials without vibration.

Uploaded by

Suniljpatil
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Rev no: ESA02/01 Date :25/03/2006

Enriching Engineering Education

ESA-02
INTRODUCTION

EEE MODEL MAKING KIT (2A & B)

1. Motorised Fret Saw. 2. Supply-230 V. AC, Single Phase , FHP motor. 3. Number of strokes per minute of the reciprocating blade =200 approx. Table area for cutting operation 30cm.x 30cm. 4. Can be used to cut a template of the required shape &size from Aluminum sheet2-3mm, Thickness by using special blades, 1-2mm,oversize on the contour by using.

MODEL CUTTER

INTRODUCTION

The specimen cut on the fret saw unit ,can be polished and counter finished to the required size by using model polisher. 1. Table floor-30cm x 30cm. 2. Power supply 230 V AC single phase. 3. Cutting Speed -18000 r.p.m. (Approx). 4. Cutting tool-1) 025dia (fine) guiding plug- 1/4. 5. Motor is well covered and ventilated to see that the plastic dust is not entering in it. Switch board, fitted on the front side consists of a fuse, push button and supply for dust collector and on-off switches.

MODEL POLISHER
PAGE 1 OF 2

ETERNAL ENGINEERING EQUIPMENT (P) LIMITED


Gat No.382,Mankarwadi Road, Near Sujnil Chemo Industries, Urawade, Pirangoot, 412111 . Tal. Mulshi , Dist. Pune Maharashtra State , INDIA.
Tel : +91 20 65600259 / 65600269 / 65600258 / 65600259 / 65600268 Email : [email protected], [email protected] WebSite : www.eeepune.com

Enriching Engineering Education

ESA-02

EEE MODEL MAKING KIT (2A & B)

NOTE Sturdy construction and accurate alignment of the tool with the guide plug is provided. The table and body are free of any vibration.

Note: 1. Since research and development is an on going activity, the specifications mentioned herein are subject to change without notice. 2. Photographs / Illustrations are only indicative in nature and will change with the exact model / specifications of the Client. PAGE 1 OF 2

ETERNAL ENGINEERING EQUIPMENT (P) LIMITED


Gat No.382,Mankarwadi Road, Near Sujnil Chemo Industries, Urawade, Pirangoot, 412111 . Tal. Mulshi , Dist. Pune Maharashtra State , INDIA.
Tel : +91 20 65600259 / 65600269 / 65600258 / 65600259 / 65600268 Email : [email protected], [email protected] WebSite : www.eeepune.com

You might also like