http://mechsuman.blogspot.

com/

ME1252: Kinematics of Machinery

Question Bank
Instructions: (Given by University Examination question paper)
1. Answer ALL questions.
2. Sketches should be drawn neatly.
3. Give brief procedure for graphical constructions.
4. Answers without units and with wrong units will carry less marks.
5. Symbols used in the solutions should be explained at least once for each answer.
6. Answers without substituting the data in the equations will carry zero marks
7. A3 size drawing sheet will be supplied on request. Use both sides of the drawing sheet, if
necessary.
8. Fold the drawing sheet to the size of the answer sheet and attach it.

2 Marks Questions
T8247, NOVEMBER 2006
1. Differentiate between machine and mechanism.
2. Write down Kutzhback criterion to find the mobility of a planar mechanism.
3. Define transmission angle and its significance.
4. How will you determine the magnitude and direction of coriolis component of
acceleration?
5. List the classifications of cam followers based on shape.
6. What are the essential design features of high speed cams?
7. Define (a) Module (b) Diametral Pitch of gears.
8. What is under cutting of gears?
9. Distinguish between sliding and rolling friction.
10. State the condition for transmission of maximum power in belt drives.

T8248, NOVEMBER 2006

11. What is Kutzbach criterion for planar mechanism?
12. Sketch an exact straight line mechanism, with link proportions.
13. Explain normal component of acceleration.
14. State Corioli's law.
15. What are the classifications of cams based on contact surfaces?
16. State the basic requirements for high speed cams.
17. Define module of gears and its relation to circular pitch.
18. Explain briefly the use of differential in an automobile.
19. What are timing belts?
20. Explain briefly significance of friction in braking.

C3298, MAY 2007

21. Enumerate the difference between a Machine and a Structure.
22. List out the inversions of a double slider crank chain.
23. Define rubbing velocity.
24. Define Corioli's component of acceleration.
25. State the expressions for maximum velocity and acceleration of a follower moves with
Cycloidal motion.
26. What is prime circle of a cam? What is the radial distance between the prime circle and
base circle for a cam with knife edge follower?
27. What is axial pitch of a helical gear?
28. List out the applications of epicyclic gear train.
http://mechsuman.blogspot.com/

29. What is the condition of maximum efficiency of a Screw jack?

30. What are the advantages of wire ropes over fabric ropes?

R3456, NOVEMBER 2007

31. Define Degree of Freedom and give the DOF for a shaft in a circular hole.
32. State Grashof’s law for a four bar linkage.
33. What is Corioli's component of acceleration?
34. State the Freudenstein's equation for a four-bar mechanism.
35. What is a circular arc cam?
36. State the expressions for maximum velocity and acceleration of a follower moves with
cycloidal motion.
37. Differentiate diametral pitch and circular pitch of a friction wheel.
38. What is reverted gear train?
39. Diagrammatically represent the forces acting on a body when it slides either up or down
on an inclined plane with out considering the effect of friction.
40. List out any four desirable characteristics of brake lining material.

T3348, APRIL 2008

41. Define degree of freedom.
42. Define Grashoffs law.
43. Explain the coriolis component of acceleration.
44. What is higher pair?
45. Define pitch curve of the cam.
46. Define undercutting in Gears.
47. Define interference in Gears.
48. Define pressure angle and explain the effect of different pressure angle.
49. What is creep in the case of belt?
50. Which type of screw thread is preferable in power transmission?

16 Marks Questions
T8247, NOVEMBER 2006
1. (i) Describe Whitworth's quick return mechanism. (6)
(ii) Distance between two parallel shafts connected by oldham’s coupling is 25 mm.
Determine maximum speed of sliding of tongue of intermediate piece in the slot in the flange
if driving shaft is run at 250 rpm. (4)
(iii) Discuss the application of Grashoff’s law in identifying the input and output motions
of four-bar mechanism. (6)

2. (i) Define and explain inversion of mechanisms. (4)

(ii) Sketch and explain oldham’s coupling. (6)
(iii) Design a four-bar crank rocker quick return mechanism to give a time ratio of 1.25
with rocker swing angle as 75° clockwise. Assume the output link (rocker) length as 50 mm
and in the left extreme position it is vertical. (6)

3. (i) A four bar mechanism DABC has the following dimensions :

DA = 300 mm; CB = AB = 360 mm; DC = 600 mm. Link DC is fixed and angle ADC is
Driving link DA turns clockwise at 100 rpm. Constant driving torque is 50 N-m. Determine
the following: (1) Velocity of point B (2) Angular velocity of driven link CB (3) Mechanical
advantage of mechanism in this position (4) Resisting torque. (12)
(ii) Sketch a four-bar crank rocker mechanism in (1) Maximum transmission angle
position and (2) toggle position where mechanical advantage is infinity. (4)
http://mechsuman.blogspot.com/

4. (i) Find the number of instantaneous centres for a six link mechanism. State the use of
instantaneous centre method in kinematic analysis. (4)
(ii) Crank of a slider crank mechanism rotates clockwise at a constant speed of 300 rpm,
crank and connecting rod are of lengths 150 mm and 600 respectively. Determine the
following; at a crank angle of 45° from inner dead centre position (1) Linear velocity and
acceleration of the midpoint of connecting rod (2) Angular velocity and angular acceleration
of the connecting rod. (12)

5. (i) Explain the following terms : (1) Prime circle (2) Pressure Angle related to cams. (4)
(ii) Draw the profile of a disc cam to give uniform motion and uniform velocity during
outstroke of 25 mm to a knife edge follower during first half revolution. Return of cam is also
of similar uniform motion with uniform velocity during remaining half revolution. Minimum
radius of the cam is 25 mm. Assume that the axis of knife edge follower passes through cam
axis. (12)

6. (i) Briefly explain the features of mushroom followers. (4)

(ii) Draw the profile of a cam to give following motion to a flat faced reciprocating
follower. (1) Follower to have a stroke of 20 mm during 120° of cam rotation. (2) Follower to
dwell for 30° of cam rotation (3) Follower to return to initial position during 120° of cam
rotation. (4) Follower to dwell for remaining 90° of cam rotation. The base circle radius is 40
mm and the follower axis coincides with cam axis of rotation. (12)

7. (i) Discuss the advantages of involute gear tooth profile. (4)

(ii) Describe the advantages and applications of helical, bevel and worm gears. (6)
(iii) In an epicyclic gear train, the sum gear A and the planet gear B are having 36 and 45
teeth respectively. If the arm rotates at 150 rpm counter clockwise about center of A which is
fixed, determine speed of gear B. If the arm is locked and gear A rotates at 300 rpm what is
the speed of gear B? (6)

8. (i) A pinion having 25 teeth drives a gear of 60 teeth. Tooth profile is involute with
pressure angle of 20°, module of 8 mm and addendum of 1 module. Determine: (1) Length of
path of contact (2) Length of arc of contact and (3)contact ratio. (6)
(ii) Design a compound gear train for an exact train ratio of 180 : 1. Minimum teeth on
any gear shall be 12 to avoid interference and Maximum gear ratio in any one stage is 10 : 1.
Also sketch the arrangement. (6)
(iii) Discuss the necessity of differentials in automobiles. (4)

9. (i) Discuss the advantages of V belts. (6)

(ii) A rope drive transmits 600 kW from a pulley of effective diameter 4 m, which runs at
90 rpm. Angle of lap is 160°; angle of groove is 45°; co-efficient of friction is 0.28; mass of
rope is 1.5 kg/m and allowable tension per rope is 2400 N. Determine the number of ropes
required. (6)
(iii) Describe the features of internal expanding brakes used in automobiles. (4)

10. (i) Following data are for a screw jack. Screw pitch is 12.5 mm; mean diameter of screw
is 50 mm; co-efficient of friction is 0.13. Determine torques to raise and lower 20 kN load
and efficiency of jack. (6)
(ii) Discuss the functions of clutches in automobiles. (4)
(iii) Derive the expression to determine the ratio of tensions in a flat belt drive. (6)
T8248, NOVEMBER 2006
11. (i) What is meant by interference in gears? What are the measures to eliminate the same?
(4)
http://mechsuman.blogspot.com/

(ii) An epicyclic train has a pinion A having 15 teeth, centrally located and rigidly
connected to shaft of driving motor. Another gear B having 20 teeth is gearing with A and
also with annular fixed wheel D. Gear C is integral with B and meshes with another annular
wheel E which is keyed to the shaft of driven unit. The arm rotates about driving shaft and
carries compound gear B, C. Sketch the arrangement and determine speed of machine for a
motor speed of 1000 rpm. Also determine torque on machine shaft for a motor torque of 100
N-m. (12)

12. Two mating gears have 20 and 40 involute teeth of module 10 mm and 20° pressure
angle. The addendum on each wheel is to be made of such a length that the line of contact on
each side of the pitch point has half the maximum possible length. Determine the addendum
height for each gear wheel, length of the path of contact, arc of contact and contact ratio.

13. (i) Explain the inversions of four bar chain, with neat sketches. (8)
(ii) Explain with neat sketches the following: (1) Offset slider mechanism, (2) An
indexing mechanism. (8)

14. (i) Explain the inversions of single slider crank chains, with neat sketches. (10)
(ii) Explain mechanical advantage and transmission angle related to four-bar mechanisms.
(6)
15. (i) Compare instantaneous center method and velocity polygon method for velocity
analysis of mechanisms. (4)
(ii) A four bar linkage has following dimensions: Crank AO2 = 150 mm; Link AB = 450
mm; Link BO4 = 300 mm; Link O2O4 = 200 mm. Link O2O4 is fixed. Find the angular
acceleration of links AB and BO4 when the crank is rotating with a constant angular velocity
of 200 rad/s counter clockwise and also positioned of 45° to horizontal. (12)

16. (i) State the properties of relative velocities of points on kinematic links. (4)
(ii) In a small steam engine running at 600 rad/min counter clockwise, length of crank is
80 mm and ratio of connecting rod length to crank radius is 3. For the position when crank
makes 45° to horizontal, determine acceleration of piston. Find also total acceleration of a
point X on connecting rod 80 from crank pin. (12)

17. Draw the profile of disc cam to give uniform acceleration and retardation out stroke of 25
to a knife edge follower during first half of revolution. Return of cam also takes place with
uniform motion during remaining half of cam revolution. Assume minimum radius of cam as
25 mm.

18. Draw the profile of a cam to give following motion to a reciprocating follower with a flat
face: (i) Follower to have a stroke of 20 mm during 120° of cam rotation. (ii) Follower to
dwell for 30° of cam rotation. (iii) Follower to return to its initial position during 120° of cam
rotation. (iv) Follower to dwell for remaining 90° of cam rotation. Minimum radius of cam =
25 mm. Out stroke and return stroke of the follower are simple harmonic.
19. (i) Pitch of 50 mm diameter threaded screw of a screw jack is 12.5 mm. Coefficient of
friction between screw and nut is 0.10. Determine the torque to raise a load of 25 kN rotating
with the screw. Also find the torque required to lower the load and efficiency of screw jack.
(4)
(ii) 100 kW is to be transmitted by a rope drive through a 160 cm diameter 45° grooved
pulley running at 200 rpm. Angle of overlap 140° and coefficient of friction between pulley
and rope is 0.25. Mass of rope is 0.7 kg/m and it can withstand a tension of 800 N.
Considering centrifugal tension, find the following: (i) Number of ropes required, (ii) Initial
tension in the rope. (12)
http://mechsuman.blogspot.com/

20. (i) Explain the following:

(1) Crowning of pulleys (3)
(2) Self-locking of brakes (3)
(3) Uses of brakes in automobiles. (2)
(ii) A 10 kW engine develops a maximum torque of 100 N-m and is driving a car having a
single plate clutch of two active surfaces. Axial pressure is not to exceed 0.85 bar. External
diameter of friction plate is 1.25 times internal diameter. Assume uniform wear and co-
efficient of friction = 0.3. Determine dimension of friction plate and axial force exerted by
the springs. (8)

C3298, MAY 2007

21. (i) Define transmission angle of a four bar linkage. What is the effect of transmission
angle on mechanical advantage? (4)
(ii) Briefly explain various types of constrained motions. (4)
(iii) Illustrate a crank and slotted lever mechanism as an inversion of single slider crank
chain. Deduce an expression for length of stroke in terms of link lengths. (8)

22. Analytically perform the displacement analysis of a four bar mechanism.

23. The driving crank AD of the quick-return mechanism, as shown in figure, revolves at a
uniform speed of 200 r.p.m. Find the velocity and acceleration of the tool-box R, in the
position shown, when the crank makes an angle of 60°with the vertical line of centers PA.
What is the acceleration of sliding of the block at B along the slotted lever PQ?

24. For the toggle mechanism as shown in figure, the slider D is constrained to move along
horizontal direction. The crank rotates at 180 rpm. The dimensions of various links are as
follows. OA = 180 mm ; CB = 240 mm; AB = 360 mm; BD = 540 mm. For the given
configuration determine the velocity of the slider and angular velocities of links AB, BC and
BD. Also determine the linear acceleration of the slider D.
http://mechsuman.blogspot.com/

25. A cam with a minimum radius of 25 mm, rotating in clockwise direction with a uniform
speed of 100 rpm is to be designed to give the motion for a roller follower as follows.
(i) To raise through 50 mm during 120° rotation of cam with SHM. (ii) Fully raised through
next 30°. (iii) To lower during next 60° with UAUR. (iv) Dwell for the remaining period.
Draw the profile of the cam when the line of stroke of the follower is offset by 15 mm from
the axis of the camshaft.

26. Construct a tangent cam and mention the important terminologies on it. Also derive the
expressions for displacement, velocity, acceleration of a reciprocating roller follower when
the roller has contact with the nose.

27. (i) An epicyclic gear train is shown in the figure. How many revolutions does the arm
makes, (1) when A makes one revolution in clockwise and D makes ½ a revolution in the
opposite sense (2) when A makes one revolution in clockwise and D remains stationary. The
number of teeth in gears A and D are 40 and 90 respectively. (10)
(ii) What is reverted gear train? Explain the arrangement of various gears in a reverted
gear train and express the characteristic equations used to define their operation. (6)

28. (i) State and prove law of gearing (4)

(ii) A pair of involute spur gears with 16° pressure angle and pitch of module 6 mm is in
mesh. The number of teeth in pinion is 16 and its rotational speed is 240 rpm. The gear ratio
is 1.75. In order to avoid the interference, determine (1) addenda on pinion and wheel (2)
length of path of contact (3) maximum velocity of sliding on either side of pitch point. (12)

29. (i) A square threaded bolt of root diameter 22.5 mm and pitch 5 mm is tightened by
screwing a nut whose mean diameter of bearing surface is 50 mm. If the coefficient of
friction between nut and bolt is 0.1 and nut and bearing surface is 0.16, determine the force
required at the end of spanner 500 mm long when the load on the bolt is 10 kN. (8)
(ii) A leather faced conical clutch has a cone angle of 30°. If the intensity of pressure
between the contact surfaces is limited to 0.35 N/mm2 and the breadth of the conical surface
is not to exceed of the mean radius. Determine the dimensions of the contact surfaces to
transmit 22.5 kW at 2000 rpm. Assume uniform wear rate and μ = 0.15. (8)

30. (i) Derive the expression for Frictional torque on cone clutch based on uniform pressure
theory. (6)
(ii) The brake whose dimensions are shown in figure has a co-efficient of friction of 0.3 and
is to have a maximum pressure of 1000 kPa against the friction material. (1) Using an
actuating force of 1750 N, determine the face width of the Shoes (both shoes have same
width) and (2) What torque will the brake absorb? (10)
http://mechsuman.blogspot.com/

R3456, NOVEMBER 2007

31. (i) Define transmission angle of a four bar linkage. What is the effect of transmission
angle on mechanical advantage? (4)
(ii) State and prove Kutchbach criterion for the following kinematic chains: Three bar
chain, Four bar chain, Cam with knife edge follower. (6)
(iii) Explain any two inversions of a four bar kinematic chain. (6)

32. Derive the displacement, velocity and acceleration equation of a slider crank mechanism.

33. For the toggle mechanism as shown in figure, the slider D is constrained to move along
horizontal direction. The crank rotates at 180 rpm. The dimensions of various links are as
follows. OA = 180 mm; CB = 240 mm; AB = 360 mm; BD = 540 mm. For the given
configuration determine (i) the velocity and acceleration of the slider (ii) angular velocity and
angular acceleration of links AB, BC and BD.

34. In a Whitworth quick return mechanism, as shown in figure, crank OA rotates at 30 rpm
in clockwise direction. The dimensions of various links are OA = 150 mm, OC = 100 mm,
CD = 125 mm and DR = 500 mm. Determine the acceleration of the sliding block R and the
angular acceleration of the slotted lever BD.
http://mechsuman.blogspot.com/

35. A cam drives a flat reciprocating follower in the following manner: (i) Follower moves
outwards through a distance of 20 mm with simple harmonic motion during the first 120°
rotation of the cam. (ii) Follower dwells during next 30° of cam rotation. (iii) Follower moves
inwards with simple harmonic motion for the next 120° of cam rotation. (iv) The follower
dwells for the remaining period. Draw the profile of the cam, when the minimum radius of
cam is 25 mm. Also calculate the maximum velocity and acceleration during outward and
inward motion of the follower when the cam rotates with 200 rpm.

36. Construct a tangent cam and mention the important terminologies on it. Also derive the
expression for displacement, velocity, acceleration of a reciprocating roller follower when the
roller has contact with the nose.

37. (i) Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is
20 and the gear ratio is 2. If the pitch expressed in module is 5 mm, and the pitch line speed is
1.2 m/s, determine the angle turned through by pinion, when one pair of teeth is in mesh.
Also calculate the maximum velocity of sliding. Take addendum as one module. (8)
(ii) Derive an expression for the minimum number of teeth required on the pinion in order
to avoid interference in involute gear teeth. (8)

38. (i) What are the special advantages of an epicyclic gear train? (4)
(ii) An epicyclic gear train for electric motor is shown in figure. The wheel S has 15 teeth
and is fixed to the motor shaft running at 1450 rpm. The planet P has 45 teeth, gears with
fixed annulus E and rotates on a spindle carried by an arm A which is fixed to the output
shaft. If the motor transmits 1.5 kW, determine the torque required to fix the annulus. (12)

39. (i) A square threaded bolt of root diameter 22.5 mm and pitch 5 mm is tightened by
screwing a nut whose mean diameter of bearing surface is 50 mm. If the coefficient of
friction between nut and bolt is 0.1 and nut and bearing surface is 0.16, determine the force
required at the end of spanner 500 mm long when the load on the bolt is 10 kN. (8)
(ii) From the first principles, derive an expression for the frictional torque of a cone clutch
under uniform wear consideration. (8)
http://mechsuman.blogspot.com/

40. (i) Determine the width of a 9.75 mm thick leather belt required to transmit 15 kW from a
motor running at 900 rpm. The diameter of the driving pulley is 300 mm. The driven pulley
runs at 300 rpm and the distance between the centers of two pulleys is 3 m. The density of the
leather can be taken as 1000 kg/mm3. Take μ = 0.3 and maximum allowable shear in the
leather = 2.5 MPa and the drive is open type. (8)
(ii) A band brake acts on the 3/4th of circumference of a drum of 450 mm diameter which
is keyed to the shaft. The band brake provides a braking torque of 225 N-m. One end of the
band is attached to a fulcrum pin of the lever and the other end to a pin 100 mm from the
fulcrum. If the operating force is applied at 500 mm from the fulcrum and the coefficient of
friction is 0.25, find the operating force when the drum rotates in anticlockwise direction. (8)
T3348, APRIL 2008
41. The crank of a slider crank mechanism is 15 cm and the connecting rod is 60 cm long.
The crank makes 300 rpm in the clockwise direction. When it has turned 45° from the inner
dead centre position determine: (i) Velocity of slider, (ii) Angular velocity of connecting rod,
(iii) Linear velocity of the mid point of the connecting rod.

42. In a four bar mechanism, the crank rotates at 36 rad/s. The lengths of the links are AB =
200 mm; BC = 400 mm; CD = 450 mm and AD = 60 mm. AD is the fixed link. At the instant
when is at right angle to AD, determine the velocity of (i) the mid point of the link BC (ii) a
point on link CD, 100 mm from the pin connecting the links CD and AD.

43. What is the importance of finding acceleration of various points in a mechanism? Name
the two different methods of finding acceleration in a mechanism.

44. What do you mean by Coriolis component of acceleration? When will it exist? Prove that
the component of acceleration is 2vω where, v = linear velocity of the slider, ω = angular
velocity of the crank.

45. From the following data draw the profile of a cam in which the follower moves with
SHM during ascent while it moves with uniformly accelerated and decelerated motion during
descent. Least radius of the cam = 50 mm; Angle of ascent = 48°; Angle of dwell= 42°;
Angle of descent= 60°; Lift of the follower= 40 mm; Diameter of the roller= 30 mm. If the
cam rotates at 360 rpm anticlockwise find the maximum velocity and acceleration of the
follower during descent.

46. A symmetrical tangent cam with a least radius of 25 mm operates a roller follower of
radius 10 mm. The angle of ascent is 60° and total lift is15 mm. If the speed of the cam is 400
rpm, then calculate : The principal dimensions of the cam, ie., the distance between the cam
centre and nose centre; nose radius and angle of control of cam with straight flank.

47. What do you mean by pitch point, circular pitch, module, addendum and pressure angle?
Explain in detail.

48. State and prove the law of gear tooth action for constant velocity ratio and show how the
involute teeth profile satisfies the condition. Derive an expression for the velocity of sliding
between a pair of involute teeth. State the advantages of involute profile as a gear tooth
profile.

49. An open belt drive connects two pulleys 120 cm and 50 cm diameters on parallel shafts 4
m apart. The maximum tension in the belt is 1855 N. The coefficient of friction is 0.3. The
driver pulley of diameter 120 cm runs at 200 rpm. Calculate: (i) the power transmitted (ii) the
torque on each of the two shafts.
http://mechsuman.blogspot.com/

50. A car moving along a level road is having the following data: Wheel base of car = 2.85
m; Height of CG from road surface = 600 mm; Perpendicular distance of CG from rear axle =
1.2 m; Speed = 60 km/h; μ = 0.1; Find the minimum distance in which the car may be
stopped when brakes are applied (i) to the rear wheels (ii) to all the four wheels.