Comparison of BS and BS EN for steel materials

Appendix

This table only highlights the comparison of BS and BS EN on steel materials, which are relevant to plan approval. Title of BS Specification for weldable structural steels BS BS 4360:1986 (Superseded, Withdrawn) BS EN
Title of BS EN

BS EN 10025:1-6:2004 Hot rolled products of structural (Current) steels Part1:General technical delivery conditions Part 2: Technical delivery conditions for non-alloy structural steels Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition Hot finished structural hollow
1

BS EN 10210-1: 2006 (Current)

sections of non-alloy and fine grain structural steels Part 1: Technical delivery requirements Steel products with improved deformation properties perpendicular to the surface of the product Technical delivery conditions Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 1: Technical delivery requirements

BS EN 10164: 2004 (Current)

BS EN 10219-1: 2006 (Current)

This table only highlights the comparison of BS and BS EN on Destructive Testing of steel materials, which are relevant to plan approval. Title of BS Method for tensile testing of metals (including aerospace materials) BS BS 18:1987 (Superseded, Withdrawn) BS EN/other standards
Title of BS EN/other standards

BS EN 10002-1:2001 Tensile testing (Current) materials.

of

metallic

Part 1: Method of test at ambient temperature ISO 6892: 1998 Metallic materials Tensile testing at ambient temperature

Methods for notched bar tests. Part 2: The Charpy V-notch impact test on metals

BS 131-2:1972 (Superseded, Withdrawn)

BS EN 10045-1: 1990 Charpy impact test on metallic (Current) materials. Part 1: Test method (V- and U-notches)

Method for Brinell hardness test and for verification of Brinell hardness testing machines

BS 240: 1986 (Superseded, Withdrawn)

BS EN ISO 6506: 1-3: Metallic materials. 2005 hardness test. (Current) Part 1: Test method.

Brinell

Part 2: Verification and calibration of testing machines Part 3: Calibration of reference blocks Method for Vickers hardness test and for verification of Vickers hardness testing machines BS 427:1990 (Superseded, Withdrawn) BS EN ISO 6507: 1-3:2005 (Current) Metallic materials. hardness test. Part 1: Test method. Vickers

Part 2: Verification and calibration of testing machines Part 3: Calibration of reference blocks
Comparison of BS and BS EN for Dimensional Tolerances

This table only highlights the comparison of BS and BS EN on dimensional tolerances of steel products, which are relevant to plan approval.
Title of BS

BS BS 4-1: 2005 (Current) -

BS EN

Title of BS EN

Structural steel sections Part 1: Specification for hot rolled sections

BS EN 10024: 1995 (Current) BS EN 10029: 1991 (Current)

Hot rolled taper flange I sections. Tolerances on shape and dimensions. Specification for tolerances on dimensions, shape and mass for hot rolled steel plates 3 mm thick or above Structural Steel I and H sections.

Weldable structural steels

BS 4360:1990 (Superseded, Withdrawn) BS 4-1: 1980

Structural steel sections

BS EN 10034: 1993
3

Part 1: Specification for hot rolled sections

(Superseded, Withdrawn) -

(Current) BS EN 10055: 1996 (Current)

Tolerances on shape and dimensions. Hot rolled steel equal flange tees with radiused root and toes. Dimensions and tolerances on shape and dimensions.

Hot rolled structural steel sections Part 4: Equal and unequal angles

BS 4848-4:1972 (Superseded, Withdrawn)

BS EN 10056-1: 1999 Specification for structural steel (Current) equal and unequal angles. Part 1: Dimensions. Specification for structural steel BS EN 10056-2: 1999 equal and unequal angles. Part 2: (Current) Tolerances on shape and dimensions.

Hot rolled structural steel sections Part 2: Specification for hot-finished hollow sections

BS 4848-2: 1991 (Superseded, Withdrawn)

BS EN 10210-2: 1997 Hot finished structural hollow (Current) sections of non-alloy and fine grain structural steels. Part 2: Tolerances, dimensions and sectional properties. BS EN 10279:2000 (Current) Hot rolled steel channels. Tolerances on shape, dimension and mass.

Specification for welded cold formed steel structural hollow sections

BS 6363:1983 (Superseded, Withdrawn)

BS EN 10219-2: 1997 Cold formed welded structural (Current) sections of non-alloy and fine grain steels. Part 2: Tolerances, dimensions and sectional properties.

Comparison of BS and BS EN on Corrosion Protection

This table only highlights the comparison of BS and BS EN on Corrosion Protection of steel, which are relevant to plan approval. Title of BS BS BS EN/other standards BS EN ISO 11124-1:1997 (Current)
4

Title of BS EN/other standards Preparation of steel substrates before application of paints and related products. Specifications

for metallic blast-cleaning abrasives. Part 1: General introduction and classification. BS EN ISO 11124-2:1997 (Current) Preparation of steel substrates before application of paints and related products. Specifications for metallic blast-cleaning abrasives. Part 2: Chilled iron.

Specification for chilled iron shot and grit

BS 2451: 1963 (Superseded, Withdrawn)

BS EN ISO 11124-3: Preparation of steel substrates 1997 before application of paints and (Current) related products. Specifications for metallic blast-cleaning abrasives. Part 3: High carbon cast-steel shot and grit. BS EN ISO 11124-4: Preparation of steel substrates 1997 before application of paints and (Current) related products. Specifications for metallic blast-cleaning abrasives. Part 4: Low carbon cast-steel shot.

Specification for sheradized coatings on iron and steel articles Specification for metallic zinc-rich priming paint (organic media) Specification for sprayed metal coatings. Part 1: Protection of iron and steel by

BS 4921: 1973 (Withdrawn, superseded) BS 4652: 1971 (Withdrawn, superseded)

BS 4921: 1988 (Current) BS 4652: 1995 (Current)

Specification for sherardized coatings on iron and steel. Specification for zinc-rich priming paint (organic media)

BS 2569-1: 1964 (Withdrawn, superseded)

BS EN 22063: 1994 (Superseded, Withdrawn) by

Metallic and other inorganic coatings. Thermal spraying. Zinc, aluminium and their alloys.

aluminium and zinc against atmospheric corrosion Specification for hot-dip galvanized coatings on iron and steel articles BS 729 : 1971 (Superseded, Withdrawn)

Thermal spraying. Metallic and other inorganic coatings. Zinc, BS EN ISO 2063: 2005 aluminium and their alloys. (Current) BS EN ISO 1461: 1999 Hot-dip galvanized coatings on (Current) fabricated iron and steel articles. Specifications and test methods.

Comparison of BS and BS EN for Welding consumables This table only highlights the comparison of BS and BS EN on welding consumables, which are relevant to plan approval. Title of BS Covered carbon and carbon manganese steel electrodes for manual metal-arc welding BS BS 639:1986 (Superseded, Withdrawn) BS EN BS EN 499: 1995 (Superseded, Withdrawn) by
Welding Title of BS EN consumablesCovered electrodes for manual metal arc welding of non-alloy and fine grain steels Classification

Welding consumables- Covered electrodes for manual metal arc BS EN ISO 2560: 2005 welding of non-alloy and fine (Current) grain steels - Classification Filler rods and wires for gas-shielded arc welding. Part 1: Ferritic steels Specification for electrode wires and fluxes for the submerged arc welding of carbon steel and medium-tensile steel BS 2901-1: 1983 (Superseded, Withdrawn) BS EN 440: 1995 (Current) Welding consumables- Wire electrodes and deposits for gas shielded metal arc welding of non-alloy and fine grain steels Classification Welding consumables- Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non-alloy and fine grain steels Classification Welding consumables- Tubular cored electrodes for metal arc welding with and without a gas shield of non-alloy and fine grain

BS 4165: 1984 (Superseded, Withdrawn)

BS EN 756: 2004 (Current)

Specification for carbon BS 7084: 1989 and carbon-manganese (Revised, Withdrawn) steel tubular cored welding electrodes

BS EN 758: 1997 (Current)

steels Classification
Comparison of BS and BS EN for Welding Standard, Procedure, Coordination and Welder

This table only highlights the comparison of BS and BS EN on Welding Standard, Procedure, Coordination and Welder, which are relevant to plan approval. Title of BS Arc welding of carbon and carbon manganese steels BS BS 5135:1984 (Superseded, Withdrawn) BS EN
Title of BS EN

Welding Recommendations for welding of metallic materials Part 1: General guidance for arc welding BS EN 1011-1:1998 (Current) Part 2: Arc welding of ferritic steels

BS EN 1011-2:2001 (Current) Specification for approval testing of welding procedures. Part 1: Fusion welding of steel. BS 4870-1:1981 (Superseded, Withdrawn) BS EN ISO 15614-1: Specification and qualification of 2004 welding procedures for metallic (Current) materials. Welding procedure test. Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys Specification and qualification of welding procedures for metallic BS EN ISO 15614-8:2002 materials welding procedure (Current) test Part 8: Welding of tubes to tube-plate joints Welding personnel. Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of

Part 3: Arc welding of tube to tube-plate joints in metallic materials

BS 4870-3:1985 (Superseded, Withdrawn)

Part 4: Specification for automatic fusion

BS 4870-4:1988 (Superseded,

BS EN 1418: 1998 (Current)

welding of metallic materials, including welding operator approval

Withdrawn)

metallic materials.

BS EN 719: 1994 (Current) BS EN 729-2: 1995 (Superseded, Withdrawn) by

Welding coordination Tasks and responsibilities Quality requirements for welding. Fusion welding of metallic materials. Comprehensive quality requirements. Quality requirements for fusion welding of metallic materials. Part 2: Comprehensive quality requirements. Quality requirements for welding. Fusion welding of metallic materials. Part 3: Standard quality requirements. Quality requirements for fusion welding of metallic materials. Part 3: Standard quality requirements Quality requirements for welding. Fusion welding of metallic materials. Part 4: Elementary quality requirements. Quality requirements for fusion welding of metallic materials. Part 4: Elementary quality

BS EN ISO 3834-2:2005 (Current) BS EN 729-3: 1995 (Superseded, Withdrawn) by

BS EN ISO 3834-3:2005 (Current) BS EN 729-4:1995 (Superseded, Withdrawn) by

BS EN ISO 3834-4:2005
8

(Current)

requirements

Specification for approval testing of welders to approved welding procedures. Fusion welding of steel Specification for approval testing of welders to approved welding procedures. Part 3: Arc welding of tube to tube-plate joints in metallic materials Specification for approval testing of welders when welding procedure approval is not required Part 1: Fusion welding of steel

BS 4871-1:1982 (Superseded, Withdrawn)

BS EN 287-1:2004 (Current)

Qualification test of welders. Fusion welding. Part 1: Steels

BS 4871-3:1985 (Current)

BS 4872-1: 1982 (Current)

Comparison of BS and BS EN for DT of welds This table only highlights the comparison of BS and BS EN on Destructive Testing of welds, which are relevant to plan approval.
Title of BS

BS BS 709:1983 (Superseded, Withdrawn)

BS EN BS EN 875: 1995 (Current)

Title of BS EN Destructive tests on welds in metallic materials. Impact tests. Test specimen location, notch orientation and examination. Destructive tests on welds in metallic materials. Longitudinal tensile test on weld metal in fusion welded joints.

Methods of destructive testing, fusion welded joints and weld metal in steel

BS EN 876: 1995 (Current)

BS EN 895: 1995 (Current) BS EN 910: 1996 (Current)

Destructive tests on welds in metallic materials. Transverse tensile test. Destructive tests on welds in metallic materials. Bend tests.

BS EN 1043-1: 1996 Destructive tests on welds in (Current) metallic materials. Hardness testing. Part 1: Hardness test on arc welded joints. BS EN 1320: 1997 (Current) BS EN 1321: 1997 (Current) Destructive test on welds in metallic materials. Fracture tests. Destructive test on welds in metallic materials. Macroscopic and microscopic examination of welds

Comparison of BS and BS EN for NDT of welds

This table only highlights the comparison of BS and BS EN on Non-Destructive Testing of welds, which are relevant to plan approval. Title of BS Code of practice. Visual inspection of fusion welded joints. Method for penetrant flaw detection. Method for magnetic particle flaw detection BS BS 5289:1976 (Superseded, Withdrawn) BS 6443:1984 (Superseded, Withdrawn) BS 6072:1981 (Current, Obsolescent, Superseded) BS EN BS EN 970:1997 (Current) BS EN 571-1:1997 (Current) BS EN 1290:1998 (Current) Title of BS EN Non-destructive examination of fusion welds Visual examination Non-destructive testing Penetrant testing Part 1: General principles Non-destructive examination of welds Magnetic particle examination of welds Non-destructive testing. Magnetic particle testing. Part 1: General principles. Non-destructive testing of

BS EN ISO 9934-1:2001 (Current) Method for ultrasonic BS 3923-1:1986 BS EN 1714:1998

examination of welds Part 1: Methods for manual examination of fusion welds in ferritic steels Radiographic examination of fusion welded butt joints in steel. Part 1: Methods for steel 2 mm up to and including 50 mm thick Part 2: Methods for steel over 50 mm up to and including 200 mm thick

(Superseded, Withdrawn)

(Current)

welded joints Ultrasonic testing of welded joints

BS 2600-1 & 2:1983 (Superseded, Withdrawn)

BS EN 1435:1997 (Current)

Non-destructive examination of welds. Radiographic examination of welded joints.

Comparison of BS and BS EN on Matching Bolt, Nut and Washer & HSFG Bolt This table only highlights the comparison of BS and BS EN on Matching Bolt, Nut and Washer & HSFG Bolt Grade 4.6 Specification for ISO metric black hexagon bolts, screws and nuts. Metric units.
Title of BS

BS
Bolt BS 4190:2001 (Current)

BS EN/other standard
BS EN ISO 4018:2001 (Current)

Title of BS EN/Other standards

Hexagon head screws. Product grade C Hexagon head bolts. Product grade C

BS EN ISO 4016:2001 (Current)

BS 7419:1991 Specification for holding down bolts (Current)

11

Nut

BS EN ISO 4034:2001 (Current)

Specification for ISO metric black hexagon bolts, screws and nuts. Metric units

BS 4190:2001 (Current) (Grade 4)

Hexagon nuts. Product grade C

Washer BS 4320:1968 Specification for metal washers for (Current) general engineering purposes. Metric series.

BS EN ISO 7091:2000 (Current)

Plain washers. Normal series. Product grade C

8.8 Specification for ISO metric black hexagon bolts, screws and nuts.

Bolt BS 4190:2001 (Current)

BS EN ISO 4017:2001 (Current)

Hexagon head screws. Product grades A and B Hexagon head bolts. Product grades A and B

BS EN ISO 4014:2001

BS 7419:1991 Specification for holding down bolts (Current) Nut

(Current)

BS EN ISO 4032:2001 (Current)

Hexagon nuts, style 1. Product grades A and B

Specification for ISO metric black hexagon bolts, screws and nuts.

BS 4190:2001 (Current) (Grade 8)

Washer BS 4320:1968 Specification for metal washers for (Current) general engineering purposes. Metric series.

BS EN ISO 7091:2000 (Current)

Plain washers. Normal series. Product grade C

12

10.9 Specification for ISO metric black hexagon bolts, screws and nuts.

Bolt BS 4190:2001 (Current)

BS EN ISO 4017:2001 (Current)

Hexagon head screws. Product grades A and B Hexagon head bolts. Product grades A and B

BS EN ISO 4014:2001 (Current) Nut BS EN ISO 4032:2001 (Current)

Specification for ISO metric black hexagon bolts, screws and nuts.

BS 4190:2001 (Current) (Grade 10)

Hexagon nuts, style 1. Product grades A and B

Washer BS 4320:1968 Specification for metal washers for (Current) general engineering purposes. Metric series.

BS EN ISO 7091:2000 (Current)

Plain washers. Normal series. Product grade C

HSFG Bolt

Specification for (Current, high strength friction grip bolts Superseded) and associated nuts and washers for structural engineering. Part 1: General grade

General grade BS 4395-1: 1969

BS EN 14399Part 1 to 6 :2005 (Current)

High-strength structural bolting assemblies for preloading. Part 1: General requirements Part 2: Suitability test for preloading Part 3: System HR. Hexagon bolt and nut assemblies Part 4: System HV. Hexagon bolt and nut assemblies Part 5: Plain washers Part 6: Plain chamfered washers

Specification for the BS 4604-1: 1970 use of high strength (Current) friction grip bolts in structural steelwork. Metric series. Part 1: General grade

13

HSFG Bolt

Specification for Higher grade high strength BS 4395-2: 1969 friction grip bolts (Current, and associated nuts Superseded) and washers for structural engineering. Part 2: Higher grade bolts and nuts and general grade washers Specification for the BS 4604-2: 1970 use of high strength (Current) friction grip bolts in structural steelwork. Metric series. Part 2: Higher grade (parallel shank)

BS EN 14399Part 1 to 6 :2005 (Current)

High-strength structural bolting assemblies for preloading. Part 1: General requirements Part 2: Suitability test for preloading Part 3: System HR. Hexagon bolt and nut assemblies Part 4: System HV. Hexagon bolt and nut assemblies Part 5: Plain washers Part 6: Plain chamfered washers

Notes:

Any bolt assemblies which seize when being tightened shall be replaced. (1) Nuts for galvanized or sheradized 8.8 bolts shall be class/grade 10. (2) Nuts for sheradized 10.9 bolts shall be class/grade 12.

14