Bulletin OZ1000 03/04

CONTROL VALVE SIZING HANDBOOK

Table of Contents
Flow Coefficient ...................................................................... Operating Conditions .............................................................. Specific Gravity........................................................................ Pressure Drop Across the Valve.............................................. Flowing Quantity...................................................................... Liquid Flow Equations ............................................................ Liquid Pressure Recovery Factor ............................................ Combined Liquid Pressure Recovery Factor .......................... Cavitation in Control Valves .................................................... Effect of Pipe Reducers .......................................................... Equations for Nonturbulent Flow ............................................ Gas and Vapor Flow Equations .............................................. Multistage Valve Gas and Vapor Flow Equations .................... Ratio of Specific Heats Factor ................................................ Expansion Factor .................................................................... Two-Phase Flow Equations .................................................... Choked Flow............................................................................ Supercritical Fluids .................................................................. Compressibility ........................................................................ Thermodynamic Critical Constants ........................................ 3 3 3 4 4 5 6 6 6 11 12 13 14 14 14 15 16 16 17 19

Engineering Data
Liquid Velocity in Steel Pipe .................................................... Steam or Gas Flow in Steel Pipe ............................................ Commercial Wrought Steel Pipe Data .................................... Temperature Conversion Table ................................................ Metric Conversion Tables ........................................................ Useful List of Equivalents ........................................................ References .............................................................................. 21 21 24 26 27 29 29

Particulars contained in this publication are for general information only and Masoneilan reserves the right to modify the contents without prior notice. No warranty either expressed or implied is either given or intended.
2004 Dresser, Inc. All rights reserved.

Foreword
This handbook on control valve sizing is based on the use of nomenclature and sizing equations from ANSI/ISA Standard S75.01.01 and IEC Standard 60534-2-1. Additional explanations and supportive information are provided beyond the content of the standards. The sizing equations are based on equations for predicting the flow of compressible and incompressible fluids through control valves. The equations are not intended for use when dense slurries, dry solids or non-Newtonian liquids are encountered. Original equations and methods developed by Masoneilan are included for two-phase flow, multistage flow, and supercritical fluids. Values of numerical factors are included for commonly encountered systems of units. These are United States customary units and metric units for both kilopascal and bar usage. The principal use of the equations is to aid in the selection of an appropriate valve size for a specific application. In this procedure, the numbers in the equations consist of values for the fluid and flow conditions and known values for the selected valve at rated opening. With these factors in the equation, the unknown (or product of the unknowns, e.g., Fp CV) can be computed. Although these computed numbers are often suitable for selecting a valve from a series of discrete sizes, they do not represent a true operating condition. Some of the factors are for the valve at rated travel, while others relating to the operating conditions are for the partially open valve. Once a valve size has been selected, the remaining unknowns, such as Fp, can be computed and a judgement can be made as to whether the valve size is adequate. It is not usually necessary to carry the calculations further to predict the exact opening. To do this, all the pertinent sizing factors must be known at fractional valve openings. A computer sizing program having this information in a database can perform this task.

Flow Coefficient CV
The use of the flow coefficient, CV, first introduced by Masoneilan in 1944, quickly became accepted as the universal yardstick of valve capacity. So useful has CV become, that practically all discussions of valve design and characteristics or flow behavior now employ this coefficient. By definition, the valve flow coefficient, CV, is the number of U.S. gallons per minute of water at 60F that will pass through a given flow restriction with a pressure drop of one psi. For example, a control valve that has a maximum flow coefficient, CV, of 12 has an effective port area in the full open position such that it passes 12 gpm of water with one psi pressure drop. Basically, it is a capacity index upon which the engineer can rapidly and accurately estimate the required size of a restriction in any fluid system.

Operating Conditions
The selection of a correct valve size, as determined by formula, is always premised on the assumption of full knowledge of the actual flowing conditions. Frequently, one or more of these conditions is arbitrarily assumed. It is the evaluation of these arbitrary data that really determines the final valve size. No formulas, only good common sense combined with experience, can solve this problem. There is no substitute for good engineering judgement. Most errors in sizing are due to incorrect assumptions as to actual flowing conditions. Generally speaking, the tendency is to make the valve too large to be on the safe side (commonly referred to as oversizing). A combination of several of these safety factors can result in a valve so greatly oversized it tends to be troublesome.

Specific Gravity
In the flow formulas, the specific gravity is a square root function; therefore, small differences in gravity have a minor effect on valve capacity. If the specific gravity is not 3 known accurately, a reasonable assumption will suffice. The use of .9 specific gravity, for example, instead of .8 would cause an error of less than 5% in valve capacity.

Pressure Drop Across the Valve

On a simple back pressure or pressure reducing application, the drop across the valve may be calculated quite accurately. This may also be true on a liquid level control installation, where the liquid is passing from one vessel at a constant pressure to another vessel at a lower constant pressure. If the pressure difference is relatively small, some allowance may be necessary for line friction. On the other hand, in a large percentage of control applications, the pressure drop across the valve will be chosen arbitrarily. Any attempt to state a specific numerical rule for such a choice becomes too complex to be practical. The design drop across the valve is sometimes expressed as a percentage of the friction drop in the system, exclusive of the valve. A good working rule is that 50% of this friction drop should be available as drop across the valve. In other words, one-third of the total system drop, including all heat exchangers, mixing nozzles, piping etc., is assumed to be absorbed by the control valve. This may sound excessive, but if the control valve were completely eliminated from such a system, the flow increase would only be about 23%. In pump discharge systems, the head characteristic of the pump becomes a major factor. For valves installed in extremely long or high-pressure drop lines, the percentage of drop across the valve may be somewhat lower, but at least 15% (up to 25% where possible) of the system drop should be taken. Remember one important fact, the pressure differential absorbed by the control valve in actual operation will be the difference between the total available head and that required to maintain the desired flow through the valve. It is determined by the system characteristics rather than by the theoretical assumptions of the engineer. In the interest of economy, the engineer tries to keep the control valve pressure drop as low as possible. However, a valve can only regulate flow by absorbing and giving up pressure drop to the system. As the proportion of the system drop across the valve is reduced, its ability to further increase flow rapidly disappears. In some cases, it may be necessary to make an arbitrary choice of the pressure drop across the valve because meager process data are available. For instance, if the valve is in a pump discharge line, having a discharge pressure of 7 bar (100 psi), a drop of 0.7 to 1.7 bar (10 to 25 psi) may be assumed sufficient. This is true if the pump discharge line is not extremely long or complicated by large drops through heat exchangers or other equipment. The tendency should be to use the higher figure. On more complicated systems, consideration should be given to both maximum and minimum operating conditions. Masoneilan Engineering assistance is available for analysis of such applications.

Flowing Quantity
The selection of a control valve is based on the required flowing quantity of the process. The control valve must be selected to operate under several different conditions. The maximum quantity that a valve should be required to pass is 10 to 15% above the specified maximum flow. The normal flow and maximum flow used in size calculations should be based on actual operating conditions, whenever possible, without any factors having been applied. On many systems, a reduction in flow means an increase in pressure drop, and the CV ratio may be much greater than would be suspected. If, for example, the maximum operating conditions for a valve are 200 gpm and 25 psi drop, and the minimum conditions are 25 gpm and 100 psi drop, the C V ratio is 16 to 1, not 8 to 1 as it would first seem. The required change in valve CV is the product of the ratio of maximum to minimum flow and the square root of the ratio of maximum to minimum pressure drop, e.g.,

200 x 100 = 16 1 25 x 25

There are many systems where the increase in pressure drop for this same change in flow is proportionally much greater than in this case.

Liquid Flow Equations

Flow of Non-vaporizing Liquid
The following equations are used to determine the required capacity of a valve under fully turbulent, nonvaporizing liquid flow conditions. Note Fp equals unity for the case of valve size equal to line size.

Choked Flow of Vaporizing Liquid

Choked flow is a limiting flow rate. With liquid streams, choking occurs as a result of vaporization of the liquid when the pressure within the valve falls below the vapor pressure of the liquid. Liquid flow is choked if

volumetric flow In this case, the following equations are used. mass flow volumetric flow

mass flow

Nomenclature
CV = valve flow coefficient N = numerical constants based on units used (see Table 1) Fp = piping geometry factor (reducer correction) FF = liquid critical pressure factor = 0.96 - 0.28 FL = liquid pressure recovery factor for a valve FLP = combined pressure recovery and piping geometry factor for a valve with attached fittings Ki = velocity head factors for an inlet fitting, dimensionless pc = pressure at thermodynamic critical point q = volumetric flow rate Gf = specific gravity at flowing temperature (water = 1) @ 60F/15.5C p1 = upstream pressure pv = vapor pressure of liquid at flowing temperature p2 = downstream pressure w = weight (mass) flow rate 1 = specific weight (mass density) upstream conditions

Numerical Constants for Liquid Flow Equations

Constant N 0.0865 N1 0.865 1.00 N2 0.00214 890.0 2.73 N6 27.3 63.3 w kg/h kg/h lb/h Units Used in Equations q m3/h m /h gpm 3

p, p kPa bar psia kPa bar psia

d, D mm in -

1 kg/m3 kg/m3 lb/ft3

Table 1

Liquid Pressure Recovery Factor FL

The liquid pressure recovery factor is a dimensionless expression of the pressure recovery ratio in a control valve. Mathematically, it is defined as follows: Liquid pressure recovery factors for various valve types at rated travel and at lower valve travel are shown in product bulletins. These values are determined by laboratory test in accordance with prevailing ISA and IEC standards.

FL =

p1 - p2 p 1 - p vc

In this expression, pvc is the pressure at the vena contracta in the valve.

Combined Liquid Pressure Recovery Factor FLP

When a valve is installed with reducers, the liquid pressure recovery of the valve reducer combination is not the same as that for the valve alone. For calculations involving choked flow, it is convenient to treat the piping geometry factor Fp and the FL factor for the valve reducer combination as a single factor FLP. The value of FL for the combination is then FLP /Fp where : p1 - p2 F LP = p 1 - p vc Fp The following equation may be used to determine FLP.
F LP = F L K i FL2 Cv
2

- 1/2

N2 d4

+ 1

where Ki = K1 + KB1 (inlet loss and Bernoulli coefficients)

Cavitation in Control Valves

Cavitation, a detrimental process long associated with pumps, gains importance in control valves due to higher pressure drops for liquids and increased employment of high pressure recovery valves (e.g. butterfly and ball valves). Cavitation, briefly, is the transformation of a portion of liquid into the vapor phase during rapid acceleration of the fluid in the valve orifice, and the subsequent collapse of vapor bubbles downstream. The collapse of vapor bubbles can produce localized pressure up to 100,000 psi (7000 bar) and are singly most responsible for the rapid erosion of valve trim under high pressure drop conditions. It is, therefore, necessary to understand and to prevent this phenomenon, particularly when high pressure drop conditions are encountered. Cavitation in a control valve handling a pure liquid may occur if the static pressure of the flowing liquid tends to decrease to a value less than the fluid vapor pressure. At this point, continuity of flow is broken by the formation of vapor bubbles. Since all control valves exhibit some pressure recovery, the final downstream pressure is generally higher than the orifice throat static pressure. When downstream pressure is higher than vapor pressure of the fluid, the vapor bubbles revert back to liquid. This two-stage transformation is defined as cavitation. The pressure recovery in a valve is a function of its particular internal geometry. In general, the more streamlined a valve is, the more pressure recovery is experienced. This increases the possibility of cavitation. The pressure recovery factor, FL, is useful for valve sizing purposes to predict limiting choked flow rate under fully cavitating conditions. However, the use of FL can be misleading to predict limiting pressure drop at which damaging cavitation will result. An enhanced cavitation prediction method is described in the ISA Recommended Practice ISA-RP75.23-1995 Considerations for Evaluating Control Valve Cavitation. The recommended practice is based on the Sigma method, where sigma is defined as:

(P 1 PV) (P 1 P 2)

The determination of sigma is based on cavitation energy levels, not on choked flow. Laboratory testing using highfrequency vibration data establishes sigma values. These sigma values then define different operational regimes for a specific product as illustrated below.

Cavitation Prediction Sigma Regimes

Four different operational regimes for each product and lift position.

Characteristics of the different cavitation regimes are:

Incipient Cavitation: Onset of cavitation Detect using high frequency vibration measurement Very local phenomenon Transient: random ticks sound Low level cavitation: usually not damaging Occurs prior to loss of capacity Constant Cavitation: More regular cavitation events Lower frequency sound and vibration sensed: rumbling sound Some damage to surfaces may occur: dependent upon valve and trim styles, and materials Maximum Cavitation: Highest vibration amplitude: sounds like marbles or gravel Vigorous, large scale cavitation Predicted by steady flow pressure distribution ( FL) Very high damage potential Manufacturers Recommended Limit: Valve style dependent Provided by manufacturer from combination of: - Application experience - Laboratory testing (Cavitation damage testing of aluminum parts) Varies with: - Size - Pressure Other application considerations: - Materials, usage duration and frequency, fluid properties - Fluid velocity Testing required for each product line: - Sigma curves established for each lift point - Minimum of two valve sizes of like geometry tested to establish size scaling factors - Minimum of two upstream pressures used to establish pressure scaling factors - The use of these two scaling factors allows the application of a particular valve geometry at various pressures and sizes while allowing the same cavitation energy levels to occur

i = Inception c = Constant mv = Maximum Vibration

Regime envelopes vary for each product and lift, and are based on laboratory testing.

mr =

Manufacturers Recommended Limit

A series of tests have to be run on multiple valve sizes, and at multiple upstream pressures to establish performance curves for each product line.

Factors Impacting Cavitation Damage

Valve Size Larger valves increase the extent of the cavitating region. Larger and more damaging bubble size. Damage Scales with: Driving Pressure High pressure is more damaging Quantified by exponent a Damage is proportional to: (P 1

P )a 2

a exponent is from testing at multiple P1 levels Scaling varies with valve Style and Geometry

Additional Factors Impacting Cavitation Damage: (Not scaled by ISA- RP75.23)

Fluid Properties Fluid Surface Tension - Higher tension, higher collapse energy, more damaging. - Water has very high surface tension. - Ammonia also has high surface tension. Fluid with multiple constituents - Multiple vapor pressures are less damaging as only a portion of the liquid cavitates at service condition. - Hydrocarbon mixtures are less damaging. Fluid with non-condensable gases - Favorable: Gas cushions bubble implosion, reducing overpressure and damage. - Unfavorable: Cavitation inception occurs earlier, at higher application sigma over a larger region. Presence of gas or solid particles foster the formation of bubbles. Temperature - Impacts gas solubility and degree of cushioning (favorable). - Pressure of vaporization, (unfavorable), higher temperature, higher Pv, increased cavitation possibility. Higher temperature decreases surface tension (favorable). Valve Materials of Construction In most instances, ALL MATERIALS WILL EVENTUALLY FAIL! Stain-Hardening: Material toughens as it plastically deforms, this is a positive trait. Ductility: Ability to deform vs. fracture. Ductile materials exhibit greater resistance than brittle materials. Hardness: This is the most important quality, the ability to resist surface pressures. The higher the hardness the greater the resistance. Temperature effects material properties, higher temperatures decrease material yield strength levels. Cavitation Can Worsen Corrosion and Chemical Attack on Materials Cavitation weakens material facilitating corrosion attack (and visa versa). Cavitation expedites removal of weakened material. Cavitation removes protective oxide layers, greatly accelerating additional material removal. Additional Considerations: Some designs can allow a degree of cavitation to occur, however, by controlling the location and energy levels, damage is avoided (Cavitation Containment Designs). For these designs the following considerations, along with the Sigma index, are also important and additional limitations are applied: Inlet and inter-stage pressure levels Valve body velocity Trim velocity Sound power levels

Calculation Method
1. Calculate Applications using Service Conditions

Calculation Example
Conditions: Water, P1 = 275 psia, P2 = 75 psia, PV= 4.0 CV reqd = 21, 3 inch Pipe Line 1. = = 1.36

2. Try 2 Inch Camflex @ CV = 21, F-T-O 2. Calculate Operating CV 3. From Product Rating @ CV Find 4. Scale 3. mr = 1.15 @ CV = 21

mr

4. Scale

mr to Service conditions
= 1.096

mr to Service Conditions

4.1 SSE =

4.1 Calculate Size Scaling Effect SSE 4.2 PSE = dr = Ref. Valve Size d = Application Valve Size b = Size Scaling Exponent 4.2 Calculate Pressure Scaling Effect PSE = 1.49

4.3 5. As

V = (mr )1.096 - 11.49 + 1

= 1.39

(1.36) < V(1.39),

Valve is Not Acceptable

Try 3 Inch Camflex in the 3 Inch Line @ CV = 21, mr = 1.06 New SSE = Reference from Testing PSE = 1.49 4.3 mr Scaled to Service Conditions and Valve Size New SSE = = 1.156

V

= 1.34

v = (mr)SSE - 1 PSE

+1

V = (mr )1.156 - 1 1.49 + 1

As

5. IF >/= V Valve is OK for Application IF < V Valve is Not Acceptable for the Application Note: See Nomenclature page 10

(1.36) > V(1.34), Valve is Acceptable

Note: Also Check Body Velocity on Camflex

Calculation Flow Chart

Calculation Sizing From Service Conditions Calculation Capacity Cv Calculation Service Conditions Select Product

Calculation

v for Valve @
Service Conditions

Calculation Size & Pressure Scaling Factors SSE/PSE From Ref. To Service

Product Flow Characteristic, W/Size & Pressure Scaling Exponents(a & b), and Rated mr @ Cv/Travel

Acceptance Criteria Additional Check Calculations If Required

>/= v ---- Acceptable < v ---- Not Acceptable

+ Velocity Checks

Nomenclature
a b Empirical characteristic exponent for calculating PSE A characteristic exponent for calculating SSE; determined from reference valve data for geometrically similar valves. Valve flow coefficient, CV = q(Gf /P)1/2 Valve inlet inside diameter, inches Valve inlet inside diameter of tested reference valve, inches Liquid pressure recovery factor Valve inlet static pressure, psia Valve outlet static pressure, psia Absolute fluid vapor pressure of liquid at inlet temperature, psia

c i mr

Cavitation index equal to (P1-PV)/(P1-P2) at service conditions, i.e., (service) Coefficient for constant cavitation; is equal to (P1-PV)/P at the conditions causing steady cavitation. Coefficient for incipient cavitation; is equal to (P1-PV)/P at the point where incipient cavitation begins to occur. Coefficient of manufacturers recommended minimum limit of the cavitation index for a specified valve and travel; is equal to minimum recommended value of (P1-PV)/P . Coefficient of cavitation causing maximum vibration as measured on a cavitation parameter plot.

CV d dr FL P1 P2 Pv

PSE Pressure Scale Effect

mv

SSE Size Scale Effect

10

Effect of Pipe Reducers

When valves are mounted between pipe reducers, there is a decrease in actual valve capacity. The reducers cause an additional pressure drop in the system by acting as contractions and enlargements in series with the valve. The Piping Geometry Factor, Fp, is used to account for this effect. Bernoulli Coefficients K B1 = 1 d D1
4

d K B2 = 1 - D 2

Piping Geometry Factor Fp =

1 C v2 K + 1 - /2 N2 d4

Summation K = K 1 + K 2 + K B1 - K B2 When inlet and outlet reducers are the same size, the Bernoulli coefficients cancel out.

Pipe Reducer Equations Loss Coefficients inlet

outlet

Nomenclature
CV = valve flow capacity coefficient d = valve end inside diameter D1 = inside diameter of upstream pipe D2 = inside diameter of downstream pipe Fp K1 = piping geometry factor, dimensionless = pressure loss coefficient for inlet reducer, dimensionless K 2 = pressure loss coefficient for outlet reducer, dimensionless K B1 = pressure change (Bernoulli) coefficient for inlet reducer, dimensionless K B2 = pressure change (Bernoulli) coefficient for outlet reducer, dimensionless K = K1 + K2 + KB1 - KB2, dimensionless

11

Equations for Non-turbulent Flow

Laminar or transitional flow may result when the liquid viscosity is high, or when valve pressure drop or CV is small. The Valve Reynolds Number Factor is used in the equations as follows : The valve Reynolds number is defined as follows :
2 2 = N 41F d q 1 FL C v + 1 FL/ C v / N 2 d4
2 2

/4

Re v

volumetric flow

Cv =

q N1 FR

Gf p1 - p2

mass flow

Cv = N6 FR

w p1 - p2

The Valve Reynolds Number Rev is used to determine the Reynolds Number Factor FR. The factor FR can be estimated from curves in the existing ISA and IEC standards, or by calculation methods shown in the standards. Iteration is required in the method shown in the IEC standard.

Nomenclature
CV = valve flow capacity coefficient d Fd FL = nominal valve size = valve style modifier, dimensionless = Liquid pressure recovery factor

Numerical Constants for Liquid Flow Equations

Constant N 0.0865 N1 N2 N4 0.865 1.00 0.00214 890.0 76000 17300 2.73 N6 27.3 63.3 w kg/h kg/h lb/h Units Used in Equations q m3/h m /h gpm m /h gpm 3 3

p, p kPa bar psia kPa bar psia

d, D mm in mm in -

1 kg/m3 kg/m3 lb/ft3

FR = Reynolds number correction factor, dimensionless Gf = specific gravity at flowing temperature (water = 1) @ 60F/15.5C p = valve pressure drop q w = volumetric flow rate = weight (mass) flow rate = mass density of liquid = kinematic viscosity, centistokes Rev = valve Reynolds number, dimensionless

Table 2

12

Gas and Vapor Flow Equations

volumetric flow Gas expansion factor

or

Pressure drop ratio

*
mass flow

*
or

Ratio of specific heats factor

*The IEC 534-2 equations are identical to the above ISA equations (marked with an *) except for the following symbols: k (ISA) corresponds to (IEC) 1 (ISA) corresponds to 1 (IEC)

Nomenclature
CV Fk FP p1 p2 q N = = = = = = = valve flow coefficient ratio of specific heats factor, dimensionless piping geometry factor (reducer correction) upstream pressure downstream pressure volumetric flow rate numerical constant based on units (see table below) gas specific gravity. Ratio of gas density at standard conditions absolute inlet temperature gas molecular weight pressure drop ratio, p/p1 Limit x = Fk xT gas compressibility factor x gas expansion factor, Y = 1 3 Fk x T

Numerical Constants for Gas and Vapor Flow Equations

Constant N
2.73 N6 27.3 63.3 4.17 N7 417.0 1360.0 0.948 N8 94.8 19.3 22.5 N9 2250.0 7320.0

Units Used in Equations w

kg/h kg/h lb/h kg/h kg/h lb/h -

q*
m /h m3/h scfh m3/h m3/h scfh
3

p, p
kPa bar psia kPa bar psia kPa bar psia kPa bar psia

1 kg/m3 kg/m 3

T1 K K R K K R K K R

lb/ft3

Gg = T1 M x Z Y xT 1 w k = = = = =

= pressure drop ratio factor = (Gamma) specific weight (mass density), upstream conditions = weight (mass) flow rate = gas specific heat ratio

*q is in cubic feet per hour measured at 14.73 psia and 60F, or cubic meters per hour measured at 101.3 kPa and 15.6 C.

Table 3

13

Multistage Valve Gas and Vapor Flow Equations

volumetric flow
Cv = q N 7 Fp p1 Y M G g T1 Z x

or
, limit xM = Fk xT

Cv =

q N 9 Fp p1 Y M

M T1 Z x

mass flow

Cv = N 6 Fp Y M
or
Cv =

w x p1
1

FM = Multistage Compressible Flow Factor (FM = 0.74 for multistage valves)

w Fp p1 Y M T1 Z x M

N8

XM = Pressure drop ratio factor for multistage valves

Ratio of Specific Heats Factor Fk

The flow rate of a compressible fluid through a valve is affected by the ratio of specific heats. The factor Fk accounts for this effect. Fk has a value of 1.0 for air at moderate temperature and pressures, where its specific heat ratio is about 1.40. For valve sizing purposes, Fk may be taken as having a linear relationship to k. Therefore,

Expansion Factor Y
The expansion factor accounts for the changes in density of the fluid as it passes through a valve, and for the change in the area of the vena contracta as the pressure drop is varied. The expansion factor is affected by all of the following influences : The factor xT accounts for the influence of 1, 2 and 3; factor Fk accounts for the influence of 4. For all practical purposes, Reynolds Number effects may be disregarded for virtually all process gas and vapor flows. As in the application of orifice plates for compressible flow measurement, a linear relationship of the expansion factor Y to pressure drop ratio x is used as below :

1. 2. 3. 4. 5.

Ratio of valve inlet to port area Internal valve geometry Pressure drop ratio, x Ratio of specific heats, k Reynolds Number

14

Two-Phase Flow Equations

Two-phase flow can exist as a mixture of a liquid with a non-condensable gas or as a mixture of a liquid with its vapor. The flow equation below applies where the twophase condition exists at the valve inlet. The flow equation accounts for expansionof the gas or vapor phase, and for possible vaporization the liquid of phase. It utilizes both the gas and liquid limiting sizing pressure drops. The flow equation for a two phase mixture entering the valve is as follows. Note : Fp equals unity for the case of valve size equal to line size. Use the actual pressure drop for pf and pg, but with the limiting pressure drop for each individually as follows :

p f = F L2 (p 1 - F F p v) p g = F k x T p 1
The use of this flow equation results in a required CV greater than the sum of a separately calculated CV for the liquid plus a CV for the gas or vapor phase. This increased capacity models published two-phase flow data quite well. For the hypothetical case of all liquid flow ( ff = 1), the flow equation reduces to the liquid flow equation for mass flow. For the hypothetical case of all gas or vapor flow (fg = 1), the flow equation reduces to the gas and vapor flow equation for mass flow.

Cv =

w N6 Fp

ff + p f f p g g Y 2

fg

Nomenclature
CV = valve flow coefficient ff = weight fraction of liquid in two-phase mixture, dimensionless fg = weight fraction of gas (or vapor) in two-phase mixture, dimensionless FF = liquid critical pressure factor = 0.96 - 0.28 Fk = FL = Fp = p1 = pv = pf = pg = w = xT = Y =
pv pc

Numerical Constants for Liquid Flow Equations

Constant N
2.73 N6 27.3 63.3

Units Used in Equations w

kg/h kg/h lb/h

q
-

p, p
kPa bar psia

d, D
-

1 kg/m3 kg/m3 lb/ft3

ratio of specific heats factor, dimensionless liquid pressure recovery factor piping geometry factor (reducer correction) upstream pressure vapor pressure of liquid at flowing temperature pressure drop for the liquid phase pressure drop for the gas phase weight (mass) flow rate of two-phase mixture pressure drop ratio factor x gas expansion factor, Y = 1 3 Fk x T

Table 4

f = specific weight (mass density) of the liquid phase at inlet conditions g = specific weight (mass density) of the gas or vapor phase at inlet conditions

15

Choked Flow (Gas and Vapor)

If all inlet conditions are held constant and pressure drop ratio x is increased by lowering the downstream pressure, mass flow will increase to a maximum limit. Flow conditions where the value of x exceeds this limit are known as choked flow. Choked flow occurs when the jet stream at the vena contracta attains its maximum cross-sectional area at sonic velocity. Values of xT for various valve types at rated travel and at lower valve travel are shown in product bulletins. These values are determined by laboratory test. When a valve is installed with reducers, the pressure ratio factor xTP is different from that of the valve alone xT. The following equation may be used to calculate xTP :
xTP = x T Fp2 xT Ki Cv2 + 1 N 5 d4
-1

where

Ki = K1 + KB1 (inlet loss and Bernoulli coefficients) The value of N5 is 0.00241 for d in mm, and 1000 for d in inches.

Supercritical Fluids
Fluids at temperatures and pressures above both critical temperature and critical pressure are denoted as supercritical fluids. In this region, there is no physical distinction between liquid and vapor. The fluid behaves as a compressible, but near the critical point great deviations from the perfect gas laws prevail. It is very important to take this into account through the use of actual specific weight (mass density) from thermodynamic tables (or the compressibility factor Z), and the actual ratio of specific heats. Supercritical fluid valve applications are not uncommon. In addition to supercritical fluid extraction processes, some process applications may go unnoticed. For instance, the critical point of ethylene is 10C (50F) and 51.1 bar (742 psia). All ethylene applications above this point in both temperature and pressure are supercritical by definition. In order to size valves handling supercritical fluids, use a compressible flow sizing equation with the weight (mass) rate of flow with actual specific weight (mass density), or the volumetric flow with actual compressibility factor. In addition, the actual ratio of specific heats should be used.

16

Compressibility Factor Z
For many real gases subjected to commonly encountered temperatures and pressures, the perfect gas laws are not satisfactory for flow measurement accuracy and therefore correction factors must be used. Following conventional flow measurement practice, the compressibility factor Z, in the equation PV = ZRT, will be used. Z can usually be ignored below 7 bar (100 psi) for common gases. The value of Z does not differ materially for different gases when correlated as a function of the reduced temperature, Tr , and reduced pressure, pr , found from Figures 1 and 2. Figure 2 is an enlargement of a portion of Figure 2. Values taken from these figures are accurate to approximately plus or minus two percent. To obtain the value of Z for a pure substance, the reduced pressure and reduced temperature are calculated as the ratio of the actual absolute gas pressure and its corresponding critical absolute pressure and absolute temperature and its absolute critical temperature.
Reduced Pressure, pr Figure 1 Compressibility Factors for Gases with Reduced Pressures from 0 to 6
(Data from the charts of L. C. Nelson and E. F. Obert, Northwestern Technological Institute) Compressibility Factor Z

The compressibility factor Z obtained from the Nelson-Obert charts is generally accurate within 3 to 5 percent. For hydrogen, helium, neon and argon, certain restrictions apply. Please refer to specialized literature.

17

Compressibility

Compressibility Factor Z Pr = inlet pressure (absolute) critical pressure (absolute) Tr = inlet temperature (absolute) critical temperature (absolute)

Figure 2 Compressibility Factors for Gases with Reduced Pressures from 0 - 40 See Page 15 for critical pressures and temperatures
(Reproduced from the charts of L. C. Nelson and E. F. Obert, Northwestern Technological Institute)

18

Reduced Pressure pr

Thermodynamic Critical Constants and Density of Elements, Inorganic and Organic Compounds
Element or Compound Critical Pressure - pc psia Acetic Acid, CH3-CO-OH Acetone, CH3-CO-CH3 Acetylene, C2H2 Air, O2+N2 Ammonia, NH3 Argon, A Benzene, C6H6 Butane, C4H10 Carbon Dioxide, CO2 Carbon Monoxide, CO Carbon Tetrachloride, CCl4 Chlorine, Cl2 Ethane, C2H6 Ethyl Alcohol, C2H5OH Ethylene, CH2=CH2 Ethyl Ether, C2H5-O-C2H5 Fluorine, F2 Helium, He Heptane, C7H16 Hydrogen, H2 Hydrogen Chloride, HCl Isobutane, (CH3) CH-CH3 Isopropyl Alcohol, CH3-CHOH-CH3 Methane, CH4 Methyl Alcohol, H-CH2OH Nitrogen, N2 Nitrous Oxide, N2O Octane, CH3-(CH2)6-CH3 Oxygen, O2 Pentane, C5H12 Phenol, C6H5OH Phosgene, COCl2 Propane, C3H8 Propylene, CH2=CH-CH3 Refrigerant 12, CCl2F2 Refrigerant 22, CHClF2 Sulfur Dioxide, SO2 Water, H2O * Standard Conditions 841 691 911 547 1638 705 701 529 1072 514 661 1118 717 927 742 522 367 33.2 394 188 1199 544 779 673 1156 492 1054 362 730 485 889 823 617 661 582 713 1142 3206 Table 5 bar (abs) 58.0 47.6 62.9 37.8 113.0 48.6 48.4 36.5 74.0 35.5 45.6 77.0 49.5 64.0 51.2 36.0 25.3 2.29 27.2 13.0 82.6 37.5 53.7 46.4 79.6 34.0 72.7 25.0 50.4 33.5 61.3 56.7 42.6 45.6 40.1 49.2 78.8 221.0 Critical Temperature - Tc F 612 455 97 -222 270 -188 552 307 88 -218 541 291 90 469 50 383 -247 -450 513 -400 124 273 455 -117 464 -233 99 565 -182 387 786 360 207 198 234 207 315 705 C 322 235 36 -141 132 -122 289 153 31 -139 283 144 32 243 10 195 -155 -268 267 -240 51 134 235 -83 240 -147 37 296 -119 197 419 182 97 92 112 97 157 374 k * Cp / CV 1.15 1.26 1.40 1.33 1.67 1.12 1.09 1.30 1.40 1.36 1.22 1.13 1.26 1.36 1.66 1.41 1.41 1.10 1.31 1.20 1.40 1.30 1.05 1.40 1.07 1.13 1.15 1.14 1.18 1.29 1.32

19

Thermodynamic Critical Constants and Density of Elements, Inorganic and Organic Compounds
Element or Compound Density - lb/ft3 14.7 psia & 60F Gas Liquid 65.7 49.4 0.069 0.0764 0.045 0.105 54.6 0.154 0.117 0.074 99.5 0.190 0.080 49.52 0.074 44.9 0.097 0.011 42.6 0.005 0.097 0.154 49.23 0.042 49.66 0.074 0.117 43.8 0.084 38.9 66.5 0.108 0.117 0.111 0.320 0.228 0.173 62.34 Table 5 (cont.) 998.6 623.1 1065.3 1.73 1.87 1.78 5.13 3.65 2.77 701.6 1.35 795.5 1.19 1.87 788.6 0.67 682.4 0.08 1.55 2.47 719.3 1.55 0.18 793.3 1.19 1593.9 3.04 1.28 874.6 2.47 1.87 1.19 Density - kg/m3 1013 mbar & 15.6C Liquid Gas 1052.4 791.3 1.11 1.223 0.72 1.68 Mol Wt 66.1 58.1 26.0 29.0 17.0 39.9 78.1 58.1 44.0 28.0 153.8 70.9 30.1 46.1 28.1 74.1 38.0 4.00 100.2 2.02 36.5 58.1 60.1 16.0 32.0 28.0 44.0 114.2 32.0 72.2 94.1 98.9 44.1 42.1 120.9 86.5 64.1 18.0

Acetic Acid, CH3-CO-OH Acetone, CH3-CO-CH3 Acetylene, C2H2 Air, O2+N2 Ammonia, NH3 Argon, A Benzene, C6H6 Butane, C4H10 Carbon Dioxide, CO2 Carbon Monoxide, CO Carbon Tetrachloride, CCl4 Chlorine, Cl2 Ethane, C2H6 Ethyl Alcohol, C2H5OH Ethylene, CH2=CH2 Ethyl Ether, C2H5-O-C2H5 Fluorine, F2 Helium, He Heptane, C7H16 Hydrogen, H2 Hydrogen Chloride, HCl Isobutane, (CH3)2 CH-CH3 Isopropyl Alcohol, CH3-CHOH-CH3 Methane, CH4 Methyl Alcohol, H-CH2OH Nitrogen, N2 Nitrous Oxide, N2O Octane, CH3-(CH2)6-CH3 Oxygen, O2 Pentane, C5H12 Phenol, C6H5OH Phosgene, COCl2 Propane, C3H8 Propylene, CH2=CH-CH3 Refrigerant 12, CCl2F2 Refrigerant 22, CHClF2 Sulfur Dioxide, SO2 Water, H2O

20

Liquid Velocity in Commercial Wrought Steel Pipe

The velocity of a flowing liquid may be determined by the following expressions : v U.S. Customary Units v Where = .321
q A

Metric Units = = = = 278 A velocity, meters/sec flow, meters3/hr cross sectional area, sq mm
q

Where

v q A

v = q = A =

velocity, ft/sec flow, gpm cross sectional area, sq in

Figure 3 gives the solution to these equations for pipes 1" through 12" over a wide flow range on both U.S. Customary and Metric Units.

Steam or Gas Flow in Commercial Wrought Steel Pipe

Steam or Gas (mass basis) To determine the velocity of a flowing compressible fluid use the following expressions : U.S. Customary Units v Where v W V A = = = = = .04 WV
A

Gas (volume basis) To find the velocity of a flowing compressible fluid with flow in volume units, use the following formulas : U.S. Customary Units v Where = .04 F
A

fluid velocity, ft/sec fluid flow, lb/hr specific volume, cu ft/lb cross sectional area, sq in

v = F = A =

fluid velocity, ft/sec gas flow, ft3/hr at flowing conditions* cross sectional area, sq in

Metric Units v Where v W V A = 278 WV

A

*Note that gas flow must be at flowing conditions. If flow is at standard conditions, convert as follows : F = Where
std ft hr
3

x 14.7 x T p 520

= = = =

fluid velocity, meters/sec fluid flow, kg/hr specific volume, m3/kg cross sectional area, mm2

p = pressure absolute, psia T = temperature absolute, R Metric Units v = 278

F A

Figure 4 is a plot of steam flow versus static pressure with reasonable velocity for Schedule 40 pipes 1" through 12" in U.S. Customary and Metric Units.

Where

v = fluid velocity, meters/sec F = gas flow, meters3/hr at flowing conditions* A = cross sectional area, sq mm

*Note that gas flow must be at flowing conditions. If flow is at standard conditions, convert as follows : F = Where
std meters hr
3

x 1.013 x T p 288

p = pressure absolute, bar T = temperature absolute, K

21

Velocity meters/second

Flow - cu. meters/hr.

Velocity - feet/second (Schedule 40 Pipe)

Figure 3 U.S. Customary Units Metric Units Liquid Velocity vs Flow Rate

22

Flow gpm

Pressure bars

Pressure - psig

Figure 4 Saturated Steam Flow vs Pressure for 1" to 12" Schedule 40 Pipe U.S. Customary Units Metric Units Velocity -- 130 to 170 feet per second --- 50 to 60 meters per second --

23

Flow lb./hr. or kg./hr.

Commercial Wrought Steel Pipe Data (ANSI B36.10)

Nominal Pipe Size mm Schedule 10 350 400 450 500 600 750 200 250 300 350 400 450 500 600 750 200 250 300 350 400 450 500 600 750 15 20 25 32 40 50 65 80 100 150 200 250 300 350 400 450 500 600 inches 14 16 18 20 24 30 8 10 12 14 16 18 20 24 30 8 10 12 14 16 18 20 24 30 /2 /4 1 11/4 11/2 2 21/2 3 4 6 8 10 12 14 16 18 20 24
3 1

O.D. inches 14 16 18 20 24 30 8.63 10.8 12.8 14.0 16.0 18.0 20.0 24.0 30.0 8.63 10.8 12.8 14.0 16.0 18.0 20.0 24.0 30.0 0.84 1.05 1.32 1.66 1.90 2.38 2.88 3.50 4.50 6.63 8.63 10.8 12.8 14.0 16.0 18.0 20.0 24.0

Wall Thickness mm 6.35 6.35 6.35 6.35 6.35 7.92 6.35 6.35 6.35 7.92 7.92 7.92 9.53 9.53 12.70 7.04 7.80 8.38 9.53 9.53 11.13 12.70 14.27 15.88 2.77 2.87 3.38 3.56 3.68 3.91 5.16 5.49 6.02 7.11 8.18 9.27 10.31 11.13 12.70 14.27 15.06 17.45 inches 0.250 0.250 0.250 0.250 0.250 0.312 0.250 0.250 0.250 0.312 0.312 0.312 0.375 0.375 0.500 0.277 0.307 0.330 0.375 0.375 0.438 0.500 0.562 0.625 0.109 0.113 0.133 0.140 0.145 0.154 0.203 0.216 0.237 0.280 0.322 0.365 0.406 0.438 0.500 0.562 0.593 0.687

I.D. inches 13.5 15.5 17.5 19.5 23.5 29.4 8.13 10.3 12.3 13.4 15.4 17.4 19.3 23.3 29.0 8.07 10.1 12.1 13.3 15.3 17.1 19.0 22.9 28.8 0.622 0.824 1.05 1.38 1.61 2.07 2.47 3.07 4.03 6.07 7.98 10.02 11.9 13.1 15.0 16.9 18.8 22.6

Flow Area mm2 92200 121900 155500 192900 280000 437400 33500 53200 76000 90900 120000 152900 187700 274200 426400 33000 52000 74200 89000 118000 148400 183200 265100 418700 190 340 550 970 1300 2150 3100 4700 8200 18600 32200 50900 72200 87100 114200 144500 179300 259300 sq in 143 189 241 299 434 678 51.9 82.5 117.9 141 186 237 291 425 661 51.2 80.7 115 138 183 230 284 411 649 0.304 0.533 0.864 1.50 2.04 3.34 4.79 7.39 12.7 28.9 50.0 78.9 112 135 177 224 278 402

*Standard wall pipe same as Schedule 40 through 10" size. 12" size data follows. 300 12 12.8 9.53 Table 6 0.375 12.00 72900 113

Schedule 40*

Schedule 30

Schedule 20

24

Commercial Wrought Steel Pipe Data (ANSI B36.10) (continued)

Nominal Pipe Size mm 15 20 25 32 40 50 65 80 100 150 200 250 300 350 400 450 500 600 15 20 25 32 40 50 65 80 100 150 200 250 300 350 400 450 500 600 15 20 25 32 40 50 65 80 100 150 200 inches /2 /4 1 11/4 11/2 2 21/2 3 4 6 8 10 12 14 16 18 20 24
3 1

O.D. inches 0.84 1.05 1.32 1.66 1.90 2.38 2.88 3.50 4.50 6.63 8.63 10.8 12.8 14.0 16.0 18.0 20.0 24.0 0.84 1.05 1.32 1.66 1.90 2.38 2.88 3.50 4.50 6.63 8.63 10.8 12.8 14.0 16.0 18.0 20.0 24.0 0.84 1.05 1.32 1.66 1.90 2.38 2.89 3.50 4.50 6.63 8.63

Wall Thickness mm 3.73 3.91 4.55 4.85 5.08 5.54 7.01 7.62 8.56 10.97 12.70 15.06 17.45 19.05 21.41 23.80 26.16 30.99 4.75 5.54 6.35 6.35 7.14 8.71 9.53 11.13 13.49 18.24 23.01 28.70 33.27 35.81 40.39 45.21 50.04 59.44 7.47 7.82 9.09 9.70 10.16 11.07 14.02 15.24 17.12 21.94 22.22 inches 0.147 0.154 0.179 0.191 0.200 0.218 0.276 0.300 0.337 0.432 0.500 0.593 0.687 0.750 0.843 0.937 1.03 1.22 0.187 0.218 0.250 0.250 0.281 0.343 0.375 0.438 0.531 0.718 0.906 1.13 1.31 1.41 1.59 1.78 1.97 2.34 0.294 0.308 0.358 0.382 0.400 0.436 0.552 0.600 0.674 0.864 0.875

I.D. inches 0.546 0.742 0.957 1.28 1.50 1.94 2.32 2.90 3.83 5.76 7.63 9.56 11.4 12.5 14.3 16.1 17.9 21.6 0.466 0.614 0.815 1.16 1.34 1.69 2.13 2.62 3.44 5.19 6.81 8.50 10.1 11.2 12.8 14.4 16.1 19.3 0.252 0.434 0.599 0.896 1.10 1.50 1.77 2.30 3.15 4.90 6.88

Flow Area mm2 150 280 460 820 1140 1900 2700 4200 7400 16800 29500 46300 65800 79300 103800 131600 163200 235400 110 190 340 680 900 1450 2300 3500 6000 13600 23500 36600 51900 63400 83200 105800 130900 189000 30 90 180 400 610 1140 1600 2700 5000 12100 23900 sq in 0.234 0.433 0.719 1.28 1.77 2.95 4.24 6.61 11.5 26.1 45.7 71.8 102 123 161 204 253 365 0.171 0.296 0.522 1.06 1.41 2.24 3.55 5.41 9.28 21.1 36.5 56.8 80.5 98.3 129 164 203 293 0.050 0.148 0.282 0.630 0.950 1.77 2.46 4.16 7.80 18.8 37.1

Schedule 80*

/2 /4 1 11/4 11/2 2 21/2 3 4 6 8 10 12 14 16 18 20 24

3

Schedule 160

/2 /4 1 11/4 11/2 2 21/2 3 4 6 8

3

*Extra strong pipe same as Schedule 80 through 8" size. 10" & 12" size data follows. 250 300 10 12 10.8 12.8 12.70 12.70 Table 6 0.500 0.500 9.75 11.8 48200 69700 74.7 108

Double Extra Strong

25

Temperature Conversion Table

C -273 -268 -240 -212 -184 -157 -129 -101 -73 -45.6 -42.8 -40 -37.2 -34.4 -31.7 -28.9 -26.1 -23.2 -20.6 -17.8 -15 -12.2 -9.4 -6.7 -3.9 -1.1 0 1.7 4.4 7.2 10 12.8 15.6 18.3 21.1 23.9 26.7 29.4 32.2 35 37.8 40.6 -459.4 -450 -400 -350 -300 -250 -200 -150 -100 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5 0 5 10 15 20 25 30 32 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105

C 43.3 46.1 48.9 54.4 60.0 65.6 71.1 76.7 82.2 87.8 93.3 98.9 104.4 110 115.6 121 149 177 204 232 260 288 316 343 371 399 427 454 482 510 538 566 593 621 649 677 704 732 762 788 816 110 115 120 130 140 150 160 170 180 190 200 210 220 230 240 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 1450 1500

F 230 239 248 266 284 302 320 338 356 374 392 410 428 446 464 482 572 662 752 842 932 1022 1112 1202 1292 1382 1472 1562 1652 1742 1832 1922 2012 2102 2192 2282 2372 2462 2552 2642 2732

-418 -328 -238 -148 -58 -49 -40 -31 -22 -13 -4 5 14 23 32 41 50 59 68 77 86 89.6 95 104 113 122 131 140 149 158 167 176 185 194 203 212 221

Note : The temperature to be converted is the figure in the red column. To obtain a reading in C use the left column; for conversion to F use the right column.

Table 7

26

Metric Conversion Tables

Multiply

By Length

To Obtain

Multiply

By Flow Rates

To Obtain

millimeters millimeters millimeters millimeters centimeters centimeters centimeters centimeters inches inches inches inches feet feet feet feet

0.10 0.001 0.039 0.00328 10.0 0.010 0.394 0.0328 25.40 2.54 0.0254 0.0833 304.8 30.48 0.304 12.0

centimeters meters inches feet millimeters meters inches feet millimeters centimeters meters feet millimeters centimeters meters inches

cubic cubic cubic cubic cubic cubic cubic cubic cubic cubic cubic cubic

feet/minute feet/minute feet/minute feet/hr feet/hr feet/hr feet/hr meters/hr meters/hr meters/hr meters/hr meters/hr

60.0 1.699 256.5 0.1247 0.472 0.01667 0.0283 4.403 16.67 0.5886 35.31 150.9

ft3/hr m3/hr Barrels/day GPM liters/min ft3/min m3/hr GPM liters/min ft3/min ft3/hr Barrels/day

Velocity
feet per second feet per second feet per second feet per second meters per second meters per second meters per second meters per second 60 0.3048 1.097 0.6818 3.280 196.9 3.600 2.237 ft/min meters/second km/hr miles/hr ft/sec ft/min km/hr miles/hr

Area
sq. millimeters sq. millimeters sq. millimeters sq. millimeters sq. centimeters sq. centimeters sq. centimeters sq. centimeters sq. inches sq. inches sq. inches sq. inches sq. feet sq. feet sq. feet sq. feet 0.010 10.-6 0.00155 1.076 x 10-5 100 0.0001 0.155 0.001076 645.2 6.452 0.000645 0.00694 9.29 x 104 929 0.0929 144 sq. centimeters sq. meters sq. inches sq. feet sq. millimeters sq. meters sq. inches sq. feet sq. millimeters sq. centimeters sq. meters sq. feet sqs. millimeters sq. centimeters sq. meters sq. inches

Weight (Mass)
pounds pounds pounds pounds short ton short ton short ton short ton long ton long ton long ton long ton kilogram kilogram kilogram kilogram metric ton metric ton metric ton metric ton 0.0005 0.000446 0.453 0.000453 2000.0 0.8929 907.2 0.9072 2240 1.120 1016 1.016 2.205 0.0011 0.00098 0.001 2205 1.102 0.984 1000 short ton long ton kilogram metric ton pounds long ton kilogram metric ton pounds short ton kilogram metric ton pounds short ton long ton metric ton pounds short ton long ton kilogram

Flow Rates
gallons US/minute GPM gallons US/minute gallons US/minute gallons US/minute gallons US/minute cubic feet/minute cubic feet/minute

3.785 0.133 8.021 0.227 34.29 7.481 28.32

liters/min ft3/min ft3/hr m3/hr Barrels/day (42 US gal) GPM liters/minute

Some units shown on this page are not recommended by SI, e.g., kilogram/sq. cm should be read as kilogram (force) / sq. cm

Table 8 27

Metric Conversion Tables (continued)

Multiply

By
Volume & Capacity

To Obtain

Multiply

By Pressure & Head

To Obtain

cubic cm cubic cm cubic cm cubic cm cubic cm cubic meters cubic meters cubic meters cubic meters cubic meters cubic feet cubic feet cubic feet cubic feet cubic feet liters liters liters liters liters gallons gallons gallons gallons gallons

0.06102 3.531 x 10-5 10.-6 0.0001 2.642 x 10-4 10.6 61,023.0 35.31 1000.0 264.2 28,320.0 1728.0 0.0283 28.32 7.4805 1000.0 61.02 0.03531 0.001 0.264 3785.0 231.0 0.1337 3.785 x 10-3 3.785

cubic inches cubic feet cubic meters liters gallons (US) cubic cm cubic inches cubic feet liters gallons cubic cm cubic inches cubic meters liters gallons cubic cm cubic inches cubic feet cubic meters gallons cubic cm cubic inches cubic feet cubic meters liters

Pressure & Head

pounds/sq. inch pounds/sq. inch pounds/sq. inch pounds/sq. inch pounds/sq. inch pounds/sq. inch pounds/sq. inch pounds/sq. inch pounds/sq. inch 0.06895 0.06804 0.0703 6.895 2.307 0.703 5.171 51.71 2.036 bar atmosphere kg/cm2 kPa ft of H2O (4 DEG C) m of H2O (4 DEG C) cm of Hg (0 DEG C) torr (mm of Hg) (0 DEG C) in of Hg (0 DEG C)

atmosphere atmosphere atmosphere atmosphere atmosphere atmosphere atmosphere atmosphere atmosphere bar bar bar bar bar bar bar bar bar kilogram/sq. cm kilogram/sq. cm kilogram/sq. cm kilogram/sq. cm kilogram/sq. cm kilogram/sq. cm kilogram/sq. cm kilogram/sq. cm kilogram/sq. cm kiloPascal kiloPascal kiloPascal kiloPascal kiloPascal kiloPascal kiloPascal kiloPascal kiloPascal millibar

14.69 1.013 1.033 101.3 33.9 10.33 76.00 760.0 29.92 14.50 0.9869 1.020 100.0 33.45 10.20 75.01 750.1 29.53 14.22 0.9807 0.9678 98.07 32.81 10.00 73.56 735.6 28.96 0.145 0.01 0.00986 0.0102 0.334 0.102 0.7501 7.501 0.295 0.001

psi bar Kg/cm2 kPa ft of H2O m of H2O cm of Hg torr (mm of Hg) in of Hg psi atmosphere Kg/cm2 kPa ft of H2O m of H2O cm of Hg torr (mm of Hg) in of Hg psi bar atmosphere kPa ft of H2O (4 DEG C) m of H2O (4 DEG C) cm of Hg torr (mm of Hg) in of Hg psi bar atmosphere kg/cm2 ft of H2O m of H2O cm of Hg torr (mm of Hg) in of Hg bar

Some units shown on this page are not recommended by SI, e.g., kilogram/sq. cm should be read as kilogram (force) /sq. cm

Table 8

28

Useful List of Equivalents (U. S. Customary Units)

1 U.S. gallon of water = 8.33 lbs @ std cond. 1 cubic foot of water = 62.34 lbs @ std cond. (= density) 1 cubic foot of water = 7.48 gallons 1 cubic foot of air = 0.076 lbs @ std cond. (= air density) Air specific volume = 1/density = 13.1 cubic feet /lb Air molecular weight M = 29 Specific gravity of air G = 1 (reference for gases) Specific gravity of water = 1 (reference for liquids) Standard conditions (US Customary) are at 14.69 psia & 60 DEG F* G of any gas = density of gas/0.076 G of any gas = molecular wt of gas/29 G of gas at flowing temp = G x 520 T + 460 Flow conversion of gas scfh = lbs/hr density scfh = lbs/hr x 379 M scfh = lbs/hr x 13.1 G Velocity of Sound C (m/sec) Flow conversion of liquid GPM = lbs/hr 500 x G *Normal conditions (metric) are at 1.013 bar and 0 DEG. C & 4 DEG. C water Note : Within this control valve handbook, the metric factors are at 1.013 bar and 15.6C. C = 91.2 where T = temp DEG C M = mol. wt k (T + 273) k = specific heat M ratio Cp/CV Velocity of sound C (ft/sec) C = 223 where T = temp DEG F M = mol. wt k ( T + 460) k = specific heat M ratio Cp/CV Universal gas equation PV = mRTZ Where P v m R = = = = = press lbs/sq ft volume in ft3 mass in lbs gas constant 1545 M P v m R = = = = = Metric Pascal m3 kg gas constant 8314 M

T = temp Rankine T = temp Kelvin Z = gas compressibility factor = Z Gas expansion (perfect gas)

P1 V1 = P 2 V2 T1 T2

References 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. The Introduction of a Critical Flow Factor for Valve Sizing, H. D. Baumann, ISA Transactions, Vol. 2, No. 2, April 1963 Sizing Control Valves for Flashing Service, H. W. Boger, Instruments and Control Systems, January 1970 Recent Trends in Sizing Control Valves, H. W. Boger, Proceedings Texas A&M 23rd Annual Symposium on Instrumentation for the Process Industries, 1968 Effect of Pipe Reducers on Valve Capacity, H. D. Baumann, Instruments and Control Systems, December 1968 Flow of a Flashing Mixture of Water and Steam through Pipes and Valves, W. F. Allen, Trans. ASME, Vol. 73, 1951 Flow Characteristics for Control Valve Installations, H. W. Boger, ISA Journal, October 1966. Flowmeter Computation Handbook, ASME, 1961 ANSI/ISA-75.01.01, Flow Equations for Sizing Control Valves IEC 60534-2-1, Sizing Equations for Fluid Flow Under Installed Conditions ISA-RP75.23-1995, Considerations for Evaluating Control Valve Cavitation Avoiding Control Valve Application Problems with Physics-Based Models, K. W. Roth and J. A. Stares Masoneilan Noise Control Manual OZ3000

29

Notes

30

Notes

31

DIRECT SALES OFFICE LOCATIONS

BELGIUM Phone: +32-2-344-0970 Fax: +32-2-344-1123 BRAZIL Phone: Fax: INDIA Mumbai Phone: Fax: New Delhi Phone: Fax: ITALY Phone: Fax: JAPAN Chiba Phone: Fax: KOREA Phone: Fax: +91-22- 8354790 +91-22-8354791 +91-11-2-6164175 +91-11-5-1659635 RUSSIA Veliky Novgorod Phone: +7-8162-15-7898 Fax: +7-8162-15-7921 Moscow Phone: +7 495-585-1276 Fax: +7 495-585-1279 SAUDI ARABIA Phone: +966-3-341-0278 Fax: +966-3-341-7624 SINGAPORE Phone: +65-6-6861-6100 Fax: +65-6-6861-7172 SOUTH AFRICA Phone: +27-11-452-1550 Fax: +27-11-452-6542 SOUTH & CENTRAL AMERICA AND THE CARIBBEAN Phone: +832-590-2303 Fax: +832-590-2529 SPAIN Phone: Fax: UNITED ARAB EMIRATES Phone: +971-4-8139-200 Fax: +971-4-8838-038 UNITED KINGDOM Woodburn Green Phone: +44-1628-536300 Fax: +44-1628-536319 UNITED STATES Massachusetts Phone: +508-586-4600 Fax: +508-427-8971 Corpus Christi, Texas Phone: +361-881-8182 Fax: +361-881-8246 Dresser Direct Deer Park, Texas Phone: +281-884-1000 Fax: +281-884-1010 Dresser Flow Technologies Houston, Texas Phone: +281-671-1640 Fax: +281-671-1735 California Phone: +562-941-7610 Fax: +562-941-7810

+55-11-2146-3600 +55-11-2146-3610

CANADA Ontario Phone: +905-335-3529 Fax: +905-336-7628 CHINA Phone: Fax:

+39-081-7892-111 +39-081-7892-208

+86-10-8486-4515 +86-10-8486-5305

+81-43-297-9222 +81-43-299-1115

FRANCE Courbevoie Phone: +33-1-4904-9000 Fax: +33-1-4904-9010 GERMANY Viersen Phone: +49-2162-8170-0 Fax: +49-2162-8170-280 Frankfurt Phone: +49-69-439350 Fax: +49-69-4970802

+82-2-2274-0748 +82-2-2274-0794

MALAYSIA Phone: +60-3-2161-0322 Fax: +60-3-2163-6312 MEXICO Phone: +52-5-310-9863 Fax: +52-5-310-5584 THE NETHERLANDS Phone: +31-10-438-4122 Fax: +31-10-438-4443

+34-93-652-6430 +34-93-652-6444

About Dresser, Inc. Dresser, Inc. is a leader in providing highly engineered infrastructure products for the global energy industry. The company has leading positions in a broad portfolio of products including valves, actuators, meters, switches, regulators, piping products, natural gas-fueled engines, retail fuel dispensers and associated retail point of sale systems and air and gas handling equipment. Leading brand names within the Dresser portfolio include Dresser Wayne retail fueling systems, Waukesha natural gas-fired engines, Masoneilan control valves, Mooney regulators, Consolidated pressure relief valves, and Roots blowers and rotary gas meters. It has manufacturing and customer service facilities located strategically worldwide and a sales presence in more than 100 countries. The companys website can be accessed at www.dresser.com.

About Dresser Masoneilan Headquartered in Houston, Dresser Masoneilan is a leading brand in the Dresser, Inc. portfolio. With a history of innovation and technological leadership that goes back more than 125 years, Dresser Masoneilan delivers flexible, best-fit process control valve solutions with interoperable instrumentation and smart technologies for a wide range of applications and industries. An open architecture technology platform offers more product application and operational flexibility. With strategically located manufacturing operations and a worldwide network of service and support facilities, Dresser Masoneilan delivers comprehensive process control solutions and services to a global market.

Dresser Masoneilan 85 Bodwell Street Avon, MA 02322-1190 Tele: 508-586-4600 / Fax: 508-941-5497 Email: [email protected]
2009 Dresser, Inc. All rights reserved.

www.dresser.com
OZ1000 03/04