Characteristics

TeSys contactors
Model d

Type of contactor

LC1LC1LC1D09D18 D25D38 D40 DT20 & DT25 DT32DT60

LC1D50D95

LC1-D115 & LC1-D150

Environment
Rated insulation voltage (Ui) Conforming to EN 60947-4-1, overvoltage category III, degree of pollution: 3 Conforming to UL, CSA Rated impulse withstand voltage (Uimp) Conforming to standards Conforming to EN 60947

V V kV

690 600 6

1000

IEC 947-1, 947-4-1, NFC 63-110, VDE 0660, BS 5424, JEM 1038, EN 60947-1, EN 60947-4-1. GL, DNV, PTB, RINA pending UL, CSA Complies with SNCF, Sichere Trennung recommendations Conforming to VDE 0106 parts 101 and A1 (project 2/89) Conforming to VDE 0106 Power connection Coil connection Protection against direct finger contact IP 2X Protection against direct finger contact IP 2X (except LC1-D40D80) TH C C C m - 60+ 80 - 5+ 60 - 40+ 70, for operation at Uc 3000 30 possible, in relation to normal vertical mounting plane V1 C gn gn gn gn 960 10 15 2 4 4 4 3 4 8 15 8 10 8 10 6 15 V 400

Product certifications

Separation insulation

Degree of protection (1) (front face only)

Protective treatment Ambient air temperature around the device

Conforming to IEC 68 Storage Operation Permissible

Maximum operating altitude Operating position Flame resistance

Without derating Without derating Conforming to UL 94 Conforming to IEC 695-2-1

Shock resistance (2) 1/2 sine wave = 11ms

Contactor open Contactor closed

Vibration resistance (2) 5300 Hz

Contactor open Contactor closed

(1) Protection ensured for the connection cross-sections shown on the next page and for connection via cable. (2) In the least favourable direction, without change of contact state (coil supplied at Ue).

Selection: pages 1/6 to 1/35 2/32

References: pages 2/6 to 2/9

Dimensions: pages 2/44 to 2/47

Schemes: pages 2/48 and 2/49

Schneider Electric

Characteristics

TeSys contactors
Model d Connections for power and control circuits

Type of contactor

LC1-

D09 & D12 D18 DT20 & (3P) DT25

D25

D32 D38 D18 (4P) DT32DT60

D40

D50 & D65

D80 & D95

D115 & D150

Power circuit connections

Connection via cable Tightening Flexible cable 1 conductor without cable end 2 conductors Flexible cable with cable end 1 conductor 2 conductors mm2 mm2 mm2 mm2 mm2 mm2 Screw clamps 14 14 14 12.5 14 14 N 2 6 N.m mm2 mm2 1.7 2.5 (4: DT25) 2.5 (4: DT25) 1.56 1.510 2.510 1.56 1.56 2.510 16 14 16 14 110 1.56 2-input connector 2.516 2.516 2.510 2.510 2.516 2.516 N 2 6 2.5 (10: DT32DT60) Screw clamps 2.525 2.516 2.525 2.510 2.525 2.516 1-input connector 2-input connector 2.525 450 2.516 425 2.525 450 2.510 416 2.525 450 2.516 425 10120 10120 + 1050 10120 10120 + 1050 10120 10120 + 1050

Solid cable 1 conductor without cable end 2 conductors Screwdriver 6 sided key Tightening torque Connection via spring terminals 1 conductor Flexible cable without cable end 2 conductors Connection via bars or lugs Bar cross-section Lug external of screw Screwdriver Phillips head flat screwdriver Phillips head flat screwdriver

1.56 1.56 1.510 1.56 1.56 2.510 N 2 6 1.7 4 4 N 2 6 2.5 4 4 N 2 6 2.5 4 4

6 8 6 8 6 8 5 5 4 9 4 12

mm mm 8 M3.5 N 2 6 N.m 1.7

8 M3.5 N 2 6 1.7

10 M4 N 2 6 2.5

10 M4 N 2 6 2.5

12 M5 N 2 6 2.5

13 M5 N 2 8 6

16 M6 N 3 8 6

3 x 16 17 M6 8 10 8

5 x 25 25 M8 13 14

Key for hexagonal headed screw Tightening torque

Control circuit connections

Connection via cable (tightening via screw clamps) Flexible cable 1 conductor without cable end 2 conductors Flexible cable with cable end 1 conductor 2 conductors mm2 mm2 mm2 mm2 mm2 mm2 14 14 14 12.5 14 14 N 2 6 1.7 14 14 14 14 14 14 14 14 14 12.5 14 14 N 2 6 1.7 14 14 12.5 12.5 14 14 N 2 6 1.2 14 14 12.5 12.5 14 14 N 2 6 1.2 14 14 12.5 12.5 14 14 N 2 6 1.2 12.5 12.5 12.5 12.5 12.5 12.5 N 2 6 1.2

14 14 14 12.5 12.5 12.5 14 14 N 2 6 1.7 14 14 N 2 6 1.7 14 14 N 2 6 1.7

Solid cable 1 conductor without cable end 2 conductors Screwdriver Tightening torque Connection via spring terminals Flexible cable 1 conductor without cable end 2 conductors Connection via bars or lugs Lug external of screw Screwdriver Tightening torque Phillips head flat screwdriver Phillips head flat screwdriver

N.m

mm2 mm2

2.5 2.5

2.5 2.5

2.5 2.5

2.5 2.5

mm mm

(1) (1)

8 M3.5

8 M3.5 N 2 6 1.2

8 M3.5 N 2 6 1.2

8 M3.5 N 2 N6 1.2

N 2 6 N.m 1.2 (1) Spade connector or cable lug, see connection via cable above.

Selection: pages 1/6 to 1/35

Schneider Electric

References: pages 2/6 to 2/9

Dimensions: pages 2/44 to 2/47

Schemes: pages 2/48 and 2/49 2/33

Characteristics

TeSys contactors
Model d

Type of contactor

LC1-

D09

DT20

D12

DT25

D18

DT32

D25

DT40

Pole characteristics
Rated operational current (Ie) (Ue 440 V) Rated operational voltage (Ue) Frequency limits Conventional thermal current (Ith) Rated making capacity (440 V) Rated breaking capacity (440 V) Permissible short-time rating No current flowing for preceding 15 minutes at 40 C In AC-3, 60 C In AC-1, 60 C Up to Of the operating current 60 C Conforming to IEC 947 Conforming to IEC 947 For 1 s For 10 s For 1 min For 10 min Without thermal overload relay, fuse gG With thermal overload relay Average impedance per pole Power dissipation per pole for the above operating currents At Ith and 50 Hz AC-3 AC-1 type 1 type 2 A A A A A A A m W W A A V Hz A 9 25 690 25400 25 250 250 210 105 61 30 25 20 20 20 12 25 690 25400 25 250 250 210 105 61 30 40 25 25 18 32 690 25400 32 300 300 240 145 84 40 50 35 32 25 40 690 25400 40 450 450 380 240 120 50 63 40 40

Protection by fuse against short-circuits (U 690 V)

See pages 2/52 and 2/53, for aM or gG fuse ratings corresponding to the associated thermal overload relay 2.5 0.20 1.56 2.5 0.36 1.56 2.5 0.8 2.5 2 1.25 3.2

a.c. control circuit characteristics

Rated control circuit voltage (Uc) Control voltage limits 50 or 60 Hz coils 50/60 Hz coils 50/60 Hz V 12690

Operational Drop-out Operational Drop-out

0.81.1 Uc on 50 Hz and 0.851.1 Uc on 60 Hz at 60 C 0.30.6 Uc at 60 C 50 Hz coil Cos 50/60 Hz coil 50 Hz coil Cos 50/60 Hz coil 60 Hz coil Cos 50/60 Hz coil 60 Hz coil Cos 50/60 Hz coil VA VA VA VA VA VA VA VA W 0.75 70 0.3 7 0.75 70 0.3 7.5 23 1222 419 15

Average consumption at 20 C and at Uc

" 50 Hz Inrush

Sealed

" 60 Hz Inrush

Sealed

Heat dissipation Operating time (3) Mechanical life in millions of operating cycles

50/60 Hz Closing C Opening O 50 or 60 Hz coil 50/60 Hz coil on 50 Hz

ms ms

Maximum operating rate In operating cycles per hour 3600 at ambient temperature 60 C (1) Protection ensured for the connection cross-sections shown on page 2/33 and for connection via cable. (2) In the least favourable direction, without change of contact state (coil supplied at Ue). (3) The closing time C is measured from the moment the coil supply is switched on to initial contact of the main poles. The opening time O is measured from the moment the coil supply is switched off to the moment the main poles separate.

Selection: pages 1/6 to 1/35 2/34

References: pages 2/6 to 2/9

Dimensions: pages 2/44 to 2/47

Schemes: pages 2/48 and 2/49

Schneider Electric

D32

DT60

D38

D40

D50

D65

D80

D95

D115

D150

32 50 690 25400 50 550 550 430 260 138 60 63 63

32 60 690 25400 60 500 500 430 260 138 60 63 63

38 50 690 25400 50 550 550 430 310 150 60 63 63

40 60 1000 25400 60 800 800 720 320 165 72 80 80

50 80 1000 25400 80 900 900 810 400 208 84 100 100

65 80 1000 25400 80 1000 1000 900 520 260 110 160 125

80 125 1000 25400 125 1100 1100 990 640 320 135 200 160

95 125 1000 25400 125 1100 1100 1100 800 400 135 200 160

115 200 1000 25400 200 1260 1100 1100 950 550 250 250 200

150 200 1000 25400 200 1660 1400 1400 1200 580 250 315 250

See pages 2/52 and 2/53, for aM or gG fuse ratings corresponding to the associated thermal overload relay 2 2 5 2 2 5 2 3 5 1.5 2.4 5.4 1.5 3.7 9.6 1 4.2 6.4 0.8 5.1 12.5 0.8 7.2 12.5 0.6 7.9 24 0.6 13.5 24

12690

24660

24500

0.81.1 Uc on 50 Hz and 0.851.1 Uc on 60 Hz at 60 C 0.30.6 Uc at 60 C 0.75 70 0.3 7 0.75 70 0.3 7.5 23 1222 419 15 3600

0.851.1 Uc at 55 C 0.30.6 Uc at 55 C 0.81.1 Uc on 50 Hz and 0.851.1 Uc on 60 Hz at 55 C 0.30.6 Uc at 55 C 200 0.75 245 20 0.3 26 220 0.75 245 22 0.3 26 610 2026 812 16 6 3600 2026 812 16 6 3600 2026 812 16 6 3600 2035 620 10 4 3600 2035 620 10 4 3600

0.851.1 Uc at 55 C 0.30.5 Uc at 55 C 0.81.15 Uc on 50/60 Hz at 55 C 0.30.5 Uc at 55 C 300 0.8 280350 22 0.3 218 300 0.8 280350 22 0.3 218 38 2050 620 8 8 2400 0.9 280350 0.9 218 0.9 280350 0.9 218 34.5 2035 4075 8 1200

Schneider Electric

2/35

Characteristics (continued)

TeSys contactors
Model d

d.c. control circuit characteristics

Type of contactor LC1D09D38 DT20DT60 $ Conforming to IEC 947-1 Conforming to UL, CSA Control voltage limits Operational Standard coil Wide range coil Drop-out V V V 12440 690 600 0.71.25 Uc at 60 C 0.10.25 Uc at 60 C Inrush Sealed Average operating time (1) at Uc Closing C W W ms 5.4 5.4 55 0.851.1 Uc at 55 C 0.751.2 Uc at 55 C 0.10.3 Uc at 55 C 22 22 85110 22 22 95130 0.751.2 Uc at 55 C 0.150.4 Uc at 55 C 270 to 365 2.45.1 2035 LC1- or LP1D40D65 12440 LC1 or LP1-D80 LC1-D115 & LC1-D150 24440

Rated control circuit voltage (Uc) Rated insulation voltage

Average consumption at 20 C and at Uc

Opening O ms 20 2035 2035 4075 Note: The arcing time depends on the circuit switched by the poles. For normal 3-phase applications, the arcing time is usually less than 10 ms. The load is isolated from the supply after a time equal to the sum of the opening time and the arcing time. Time constant (L/R) Mechanical life at Uc Maximum operating rate at ambient temperature 60 C In millions of operating cycles In operating cycles per hour ms 28 30 3600 65 20 3600 75 20 3600 25 8 1200

Low consumption control circuit characteristics

Rated insulation voltage Conforming to EN 60947-1 Conforming to UL, CSA Maximum voltage Average consumption d.c. at 20 C and at Uc Of the control circuit on $ V V 690 600 250

Wide range coil (0.71.25 Uc)

Inrush Sealed

W W ms ms

2.4 2.4 70 25 0.7 to 1.25 Uc 0.10.3 Uc

Operating time (1) at Uc and at 20 C Voltage limits ( 60 C) of the control circuit

Closing Opening Operational Drop-out

C O

Time constant (L/R) Mechanical life In millions of operating cycles

ms

40 30

Maximum operating rate At ambient temperature 60 C ops/h 3600 (1) Operating times depend on the type of contactor electromagnet and its control mode. The closing time C is measured from the moment the coil supply is switched on to initial contact of the main poles. The opening time O is measured from the moment the coil supply is switched off to the moment the main poles separate. (2) In the least favourable direction, without change of contact state.

Selection: pages 1/6 to 1/35 2/36

References: pages 2/6 to 2/9

Dimensions: pages 2/44 to 2/47

Schemes: pages 2/48 and 2/49

Schneider Electric

Characteristics (continued)

TeSys contactors
Model d

Contactor integral auxiliary contact characteristics

Linked contacts conforming to draft standard IEC 947-4-5 Mirror contact Rated operational voltage (Ue) Rated insulation voltage (Ui) Each contactor has 2 N/O and N/C contacts mechanically linked on the same movable contact holder The N/C contact on each contactor represents the state of the power contacts and can be connected to a PREVENTA safety module Up to Conforming to IEC 947-1 Conforming to UL, CSA Conventional thermal current (Ith) Operating current frequency Minimum switching capacity = 108 Short-circuit protection Rated making capacity Short-time rating U min. I min. Conforming to EN 60947-5-1 Conforming to EN 60947-5-1, I rms Permissible for 1s 500 ms 100 ms A A A A M Guaranteed between N/C and N/O contacts a.c. supply categories AC-14 and AC-15 Electrical life (valid for up to 3600 operating cycles/hour) on an inductive load such as the coil of an electromagnet: making power (cos 0.7) = 10 times the power broken (cos 0.4). V VA VA VA 24 60 16 4 48 120 32 8 115 280 80 20 230 560 160 40 400 960 280 70 440 1050 300 80 DC-13
Millions of operating cycles

V V V A Hz V mA

690 690 600 10 25400 17 5 gG fuse: 10 A ": 140, $: 250 100 120 140 > 10 1.5 on energisation and on de-energisation

For ambient temperature 60 C

Insulation resistance Non-overlap time

ms

Contact operating power conforming to EN 60947-5-1

d.c. supply category DC-13 Electrical life (valid for up to 1200 operating cycles/hour) on an inductive load such as the coil of an electromagnet, without economy resistor, the time constant increasing with the load. V W W W 24 96 48 14 48 76 38 12 125 76 38 12 250 76 32 440 44

1 million operating cycles 3 million operating cycles 10 million operating cycles AC-15
Millions of operating cycles

600 1440 420 100

1 8 7 6 5 4 3 2

1 8 7 6 5 4 3 2 250 V

24 V 48 V 125 V

1 0,8 0,7 0,6 0,5 0,4 0,3 0,2

1 0,8 0,7 0,6 0,5 0,4 0,3 0,2

440 V

0,1 0,1 0,2 0,3 0,4 0,5 0,6 0,8 1 0,7 0,9 2 3 6 8 10 5 7 9 Current broken in A 4

0,1 0,1 0,2 0,3 0,4 0,5 0,6 0,8 1 0,7 0,9 2 3 6 8 10 5 7 9 Current broken in A 4

Selection: pages 1/6 to 1/35

Schneider Electric

References: pages 2/6 to 2/9

Dimensions: pages 2/44 to 2/47

Schemes: pages 2/48 and 2/49 2/37

Characteristics

TeSys contactors
Auxiliary contact blocks without dust and damp protected contacts for model d contactors

Contact block type

LAD-N or C LAD-T & S

LAD-R

LAD-8

Environment
Conforming to standards Product certifications Protective treatment Degree of protection Ambient air temperature around the device Conforming to IEC 68 Conforming to VDE 0106 Storage Operation Permissible for operation at Uc Maximum operating altitude Without derating Phillips N 2 and 6 mm Flexible or solid cable with or without cable end Flexible or solid cable without cable end C C C m mm2 mm2 IEC 947-5-1, NF C 63-140, VDE 0660, EN 60947-5-1 UL, CSA TH Protection against direct finger contact IP 2X - 60+ 80 - 5+ 60 - 40+ 70 3000 Min.: 1 x 1; max.: 2 x 2.5 Max.: 2 x 2.5

Cabling Connection by spring terminals

Instantaneous and time delay contact characteristics

Number of contacts Rated operational voltage (Ue) Rated insulation voltage (Ui) Up to Conforming to EN 60947-5-1 Conforming to UL, CSA Conventional thermal current (Ith) Frequency of operational current Minimum switching capacity U min. I min. Short-circuit protection Rated making capacity Short-time rating For ambient temperature 60 C V V V A Hz V mA 1, 2 or 4 690 690 600 10 25400 17 5 10 ": 140; $: 250 100 120 140 > 10 1.5 (on energisation and on de-energisation) 1.5 30 - 40+ 70 2% + 15 % - 40+ 70 2% + 15 % 2 2 2

Conforming to EN 60947-5-1 and VDE 0660. gG fuse A Conforming to EN 60947-5-1, I rms Permissible for: 1s 500 ms 100 ms A A A A M Guaranteed between N/C and N/O contacts Guaranteed between N/C and N/O on LAD-C22 Ambient air temperature for operation Repeat accuracy Drift up to 0.5 million operating cycles Drift depending on ambient air temperature ms ms C

Insulation resistance Non-overlap time Overlap time Time delay (LAD-T, R and S contact blocks) Accuracy only valid for setting range indicated on the front face

0.25 % per C 0.25 % per C 5 5 30

Mechanical durability Operational power of contacts

In millions of operating cycles

See page 2/40

References: pages 2/17 and 2/18 2/38

Dimensions: pages 2/44 and 2/45

Schemes: pages 2/48 and 2/49

Schneider Electric

Characteristics

TeSys contactors
Auxiliary contact blocks with dust and damp protected contacts for model d contactors

Contact block type

LA1-DX

LA1-DX protected

LA1-DY non protected

Environment
Conforming to standards Product certifications Protective treatment Degree of protection Ambient air temperature Cabling Conforming to IEC 68 Conforming to VDE 0106 Storage and operation Phillips N 2 and 6 mm Flexible or solid cable with or without cable end C IEC 947-5-1, VDE 0660 UL, CSA TH Protection against direct finger contact IP 2X - 25+ 70

mm2

Min.: 1 x 1 Max.: 2 x 2.5 2 2 2 2

Number of contacts

Contact characteristics
Rated operational voltage (Ue) Rated insulation voltage (Ui) Up to Conforming to IEC 947-5-1 Conforming to UL, CSA Conventional thermal current (Ith) Maximum operational current (Ie) Frequency of operational current Minimum switching capacity U min. I min. Short-circuit protection Rated making capacity Short-time rating For ambient temperature 40 C V V V A mA Hz V mA 50 250 50 3 0.3 > 10 5 Gold - Single break with crossed bars 50 250 50 3 0.3 > 10 5 Gold - Single break with crossed bars 690 690 600 10 10 25400 17 5 10 ": 140; $: 250 100 120 140 > 10 30 24 250 50 3 0.3 > 10 5 Gold - Single break with crossed bars

Conforming to EN 60947-5-1. gG fuse A Conforming to EN 60947-5-1, I rms Permissible for: 1s 500 ms 100 ms A A A A M In millions of operating cycles

Insulation resistance Mechanical durability Materials and technology used for dust and damp protected contacts

References: page 2/17

Schneider Electric

Dimensions: pages 2/44 and 2/45

Schemes: pages 2/48 and 2/49 2/39

Characteristics

TeSys contactors
Auxiliary contact blocks with dust and damp protected contacts for model d contactors

Operational power of contacts (conforming to EN 60947-5-1)

a.c. supply, categories AC-14 and AC-15 Electrical durability (valid up to 3600 operating cycles/hour) on an inductive load such as the coil of an electromagnet: making power (cos 0.7) = 10 times the power broken (cos 0.4). V VA VA VA 24 60 16 4 48 120 32 8 115 280 80 20 230 560 160 40 400 960 280 70 440 1050 300 80 600 1440 420 100

1 million operating cycles 3 million operating cycles 10 million operating cycles

Millions of operating cycles

1 8 7 6 5 4 3 2

1 0,8 0,7 0,6 0,5 0,4 0,3 0,2

0,1 0,1 0,2 0,3 0,4 0,5 0,6 0,8 1 0,7 0,9 2 3 6 8 10 5 7 9 Current broken in A 4

d.c. supply, category DC-13 Electrical durability (valid up to 1200 operating cycles/hour) on an inductive load such as the coil of an electromagnet, without economy resistor, the time constant increasing with the power. V W W W 24 120 70 25 48 90 50 18 125 75 38 14 250 68 33 12 440 61 28 10

1 million operating cycles 3 million operating cycles 10 million operating cycles

Millions of operating cycles

1 8 7 6 5 4 3 2 250 V

24 V 48 V 125 V

1 0,8 0,7 0,6 0,5 0,4 0,3 0,2

440 V

0,1 0,1 0,2 0,3 0,4 0,5 0,6 0,8 1 0,7 0,9 2 3 4 6 8 10 5 7 9 Current broken in A

References: pages 2/17 and 2/18 2/40

Dimensions: pages 2/44 and 2/45

Schemes: pages 2/48 and 2/49

Schneider Electric

Characteristics

TeSys contactors
Control modules, coil suppressor modules and mechanical latch blocks for model d contactors

Environment
Conforming to standards Product certifications Protective treatment Degree of protection Ambient air temperature around the device Conforming to IEC 68 Conforming to VDE 0106 Storage Operation Permissible for operation at Uc C C C IEC 947-5-1 UL, CSA TH Protection against direct finger contact IP 2X - 40+ 80 - 25+ 55 - 25+ 70

Auto - Man - Stop control modules

Recommendation Rated insulation voltage Rated operational voltage Protection Built-in protection Indication Electrical durability The Auto - Man selector switch must only be operated with the Start - Stop (O I) switch in position O Conforming to EN 60947-5-1 Conforming to EN 60947-5-1 Against electric shocks Contactor coil suppression By integral LED In operating cycles V V kV 250 250 2 By varistor Illuminates when the contactor coil is energised 20,000

Coil suppressor modules

Module type Type of protection LA4-DA LAD-4RC RC circuit LA4-DB LAD-4T Bidirectional peak limiting diode " or $ 2472 2 Uc LA4-DC Diode LA4-DE LAD-4V Varistor

Rated control circuit voltage (Uc) Maximum peak voltage Natural RC frequency 24/48 V 50/127 V 110/240 V 380/415 V

" 24415 3 Uc

$ 12250 Uc

" or $ 24250 2 Uc

Hz Hz Hz Hz

400 200 100 150

Mechanical latch blocks

Mechanical latch block type For mounting on contactor LA6-DK10 LC1D40D65, LP1-D65 UL, CSA Conforming to IEC 947-5-1 " 50/60 Hz and $ For unlatching In operating cycles/hour " $ V V VA W 690 24415 25 30 LAD-6K10 LC1-D09D38, DT20DT60 LA6-DK20 LC1-D80D150 LP1-D80 and LC1-D115 UL, CSA 690 24415 25 30

Certification Rated insulation voltage Rated control circuit voltage Power required Maximum operating rate On-load factor Mechanical durability at Uc

1200 1200 10 % 10 % In millions of operating cycles 0.5 0.5 Unlatching can be manually operated locally or electrically controlled for remote operation. The LA6-DK or LAD-6K latch coil and the LC1-D operating coil must not be energised simultaneously. The duration of the LA6-DK or LAD-6K and LC1-D control signals must be 100 ms.

References: pages 2/18 to 2/21

Schneider Electric

Dimensions: pages 2/44 and 2/45

Schemes: pages 2/48 and 2/49 2/41

Characteristics

TeSys contactors
Electronic serial timer modules for model d contactors

Module type

LA4-DT (On-delay)

LA4-DR (Off-delay) for LC1-D

Environment
Conforming to standards Product certifications Protective treatment Degree of protection Ambient air temperature around the device Rated insulation voltage (Ui) Cabling IEC 255-5 UL, CSA TH Protection against direct finger contact IP 2X C C C V - 40+ 80 - 25+ 55 - 25+ 70 250

Conforming to IEC 68 Conforming to VDE 0106 Storage Operation For operation at Uc Conforming to EN 60947-5-1 Phillips N 2 and 6 mm Flexible or solid cable with or without cable end

mm2 Min.: 1 x 1 Max.: 2 x 2.5

Control circuit characteristics

Built-in protection Rated control circuit voltage (Uc) Permissible variation Type of control On input Suppression of contactor V By varistor By varistor " or $ 24250 0.81.1 Uc By mechanical contact only By varistor By bidirectional peak limiting diode " 24250 0.81.1 Uc By mechanical contact only, connecting cable < 10 m

Time delay characteristics

Timing ranges Repeat accuracy Reset time Immunity to micro-breaks Minimum control pulse duration Indication of time delay By LED 040 C During the time delay period After the time delay period During the time delay period After the time delay period ms ms ms ms ms s 0.12; 1.530; 25500 3 % (10 ms minimum) 150 50 10 2 Illuminates during time delay period 0.12; 1.530; 25500 3 % (10 ms minimum) 225 20 40 Illuminates during time delay period

Switching characteristics (solid state type)

Maximum power dissipated Leakage current Residual voltage Overvoltage protection Electrical durability In millions of operating cycles W mA V 2 <5 3.3 3 kV; 0.5 joule 30 3.5 <5 3.3 3 kV; 0.5 joule 30

Operating diagrams
LA4-DT On-delay electronic timers LA4-DR Off-delay electronic timers U supply (A1-A2) U supply (A1-A2) Time delay output Contactor coil Red LED Red LED
1 0 1 0 t 1 0 1 0 1 0 t

40 ms

Control (A2-B2) Time delay output Contactor coil

References: page 2/21 2/42

Dimensions: pages 2/44 and 2/45

Schemes: pages 2/48 and 2/49

Schneider Electric

Characteristics

TeSys contactors
Interface modules for model d contactors

Environment
Conforming to standards Product certifications Protective treatment Degree of protection Ambient air temperature around the device Conforming to IEC 68 Conforming to VDE 0106 Storage Operation Permissible for operation at Uc C C C IEC 255-5 UL, CSA TH Protection against direct finger contact IP 2X - 40+ 80 - 25+ 55 - 25+ 70

Other characteristics
Module type LA4DFBQ With relay Conforming to EN 60947-5-1 Conforming to EN 60947-5-1 V V 5 415 LA4DFB With relay 250 250 LA4DFE With relay LA4LA4DLB DLE With relay + override LA4DWB Solid state

Rated insulation voltage Rated operational voltage Indication of input state Input signals

By integral LED which illuminates when the contactor coil is energised Control voltage (E1-E2) Permissible variation Current consumption at 20 C State 0 guaranteed for U I State 1 guaranteed for U V V mA V mA V $ 24 1730 25 < 2.4 <2 17 By diode By diode 3 ms At 20 C With coil: " 24250 V " 100250 V " 380415 V W 4 0.6 10 4 0.6 10 4 0.6 3 4 0.6 3 4 0.6 20 1 0.4 LC1-D40D115 LC1-D09D38, DT20DT60 $ 24 $ 48 $ 24 $ 48 $ 24

1730 3360 1730 3360 530 25 < 2.4 <2 17 15 < 4.8 < 1.3 33 25 < 2.4 <2 17 15 < 4.8 < 1.3 33 8.5 for 5 V 15 for 24 V < 2.4 <2 5

Built-in protection Electrical durability at 220/240 V Maximum immunity time to micro-breaks Power dissipated Direct mounting without contactor

Against reverse polarity Of the input In millions of operating cycles

LC1-D40D150

LC1-D40D150 LC1-D09D38, DT20DT60 LC1-D09D38, DT20DT60

Mounting with cabling adaptor LAD-4BB

With coil:

" 24250 V " 380415 V

Total operating time at Uc (of the contactor)

Operating times depend on the type of contactor electromagnet and its control mode. The closing time C is measured from the moment the coil supply is switched on to initial contact of the main poles. The opening time O is measured from the moment the coil supply is switched off to the moment the main poles separate. LC1-D09D38, DT20DT60 2030 1624 Min.: 1 x 1 Min.: 2 x 2.5
LC1-D40D65 LC1-D80 and D95

With LA4-DF, DL Cabling Phillips N 2 and 6 mm Flexible or solid cable with or without cable end

N/O ms N/C ms mm2 mm2

2834 2024

2843 1832

References: page 2/21

Schneider Electric

Dimensions: pages 2/44 and 2/45

Schemes: pages 2/48 and 2/49 2/43