Scribd
Upload
52 views

Unit Com

The document discusses a simple unit commitment problem in power generation. It involves determining which generating units to operate over time periods to minimize costs while meeting demand and accounting for unit constraints like startup costs and minimum up and down times. Lagrangian relaxation is presented as an optimization method for solving the unit commitment problem.

Uploaded by

Mohammad Faisal Hamid
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
52 views

Unit Com

The document discusses a simple unit commitment problem in power generation. It involves determining which generating units to operate over time periods to minimize costs while meeting demand and accounting for unit constraints like startup costs and minimum up and down times. Lagrangian relaxation is presented as an optimization method for solving the unit commitment problem.

Uploaded by

Mohammad Faisal Hamid
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 12

A Simple Unit Commitment Problem

Valentn Petrov, James Nicolaisen 18 / Oct / 1999 NSF meeting

Economic Dispatch (Covered last time)


G

G
G G G

With a given set of units running, how of the load much should be generated at each to cover the load and losses? This is the question of Economic dispatch. The solution is for the current state of the network and does not typically consider future time periods.

Deciding which units to commit


G
G G G G G G G G

When should the generating units (G) controlled by the GENCO be run for most economic operation?
Concern must be given to environmental effects

How does one define economic operation? Profit maximizing? Cost minimizing? Depends on the market youre in.

Problem Setup
Last meeting we discussed the economic dispatch problem Now we will see how the unit commitment fits into the general picture Unit commitment is bound to the economic dispatch Use similar optimization methods

What is Unit Commitment (1)


We have a few generators (units) Also we have some forecasted load Besides the cost of running the units we have additional costs and constraints
start-up cost shut-down cost spinning reserve ramp-up time... and more

What is Unit Commitment (2)


It turns out that we cannot just flip the switch of certain units on and use them! We need to think ahead, and based on the forecasted load and unit constraints, determine which units to turn on (commit) and which ones to keep down Minimize cost, cheap units play first Expensive ones run only when demand is high

How Do We Solve the Problem


If a unit is on, we designate this with 1 and respectively, the off unit is 0 So, somehow we decide that for the next hour we will have "0 1 1 0 1" if we have five units Based on that, we solve the economic dispatch problem for unit 2, 3 and 5 We start turning on U2, U3, U5 When the next hour comes, we have them up and running

To Come Up With Unit Commitment


The question is, _how_ do we come up with this unit commitment "0 1 1 0 1" ? One very simplistic way: if we have very few units, go over all combinations from hour to hour For each combination at a given hour, solve the economic dispatch For each hour, pick the combination giving the lowest cost!

Lagrange Relaxation (1)


Min f = (0.25 x21+15)U1 + (0.255 x22+15)U2 subject to:
W = 5 x1U1 - x2U2 0 < x1 < 10 0 < x2 < 10

U may be only 0 or 1

Lagrange Relaxation (2)


L = (0.25 x21+15)U1 + (0.255 x22+15)U2 + l(5 x1U1 - x2U2) Pick a value for l and keep it fixed Minimize for U1 and U2 separately 0 = d/dx1(0.25x21 + 15 - x1l1) 0 = d/dx2(0.255x22 + 15 - x2l1)

Lagrange Relaxation (3)


0 = d/dx1(0.25x21 + 15 - x1l1)
if the value of x1 satisfying the above falls outside the 0 < x1 < 10, we force x1 to the limit. If the term in the brackets is > 0, set U1 to 0, otherwise keep it 1

0 = d/dx2(0.255x22 + 15 - x2l1)
same as above

Lagrange Relaxation (4)


Now assume the variables x1, x2, U1, U2 fixed Try to maximize L by moving l1 around dL/dl = (5 x1U1 - x2U2) l2 = l1 + dL/dl (a)
if dL/dl > 0, a = 0.2 if dL/dl < 0, a = 0.005

After we found l2, repeat the whole process starting at step 1

You might also like