Scribd
Upload
41 views

Practica Vlans

The document outlines the steps to configure VLAN trunking between switches and routers. It involves: 1) Configuring the router interfaces and IP addresses for each VLAN. 2) Configuring one switch as the VTP server and another as the client to propagate VLAN definitions. 3) Creating VLANs on the server switch and configuring trunk ports between the switches. 4) Configuring access ports on each switch for the appropriate VLANs. 5) Assigning IP addresses to the switch VLAN interfaces.

Uploaded by

juancarlosvesga
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
41 views

Practica Vlans

The document outlines the steps to configure VLAN trunking between switches and routers. It involves: 1) Configuring the router interfaces and IP addresses for each VLAN. 2) Configuring one switch as the VTP server and another as the client to propagate VLAN definitions. 3) Creating VLANs on the server switch and configuring trunk ports between the switches. 4) Configuring access ports on each switch for the appropriate VLANs. 5) Assigning IP addresses to the switch VLAN interfaces.

Uploaded by

juancarlosvesga
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 8

PASO 1.

CONFIGURACION DEL ROUTER Router> Router>ENABLE Router#CONFIGURE TERMINAL Router(config)#HOSTNAME ROUTER1 Levantamos la interfaz FE0/0 ROUTER1(config)#INTERFACE F0/0 ROUTER1(config-if)#NO SHUTDOWN ROUTER1(config-if)#EXIT Establecemos encapsulamiento 802.1Q a la VLAN 1 ROUTER1(config)#INTERFACE F0/0.1 ROUTER1(config-subif)#ENCAPSULATION DOT1Q 1 ROUTER1(config-subif)#IP ADDRESS 10.10.1.1 255.255.255.0 ROUTER1(config-subif)#EXIT

Establecemos encapsulamiento 802.1Q a la VLAN 2 ROUTER1(config)#INTERFACE F0/0.2 ROUTER1(config-subif)#ENCAPSULATION DOT1Q 2 ROUTER1(config-subif)#IP ADDRESS 10.10.2.1 255.255.255.0 ROUTER1(config-subif)#EXIT Establecemos encapsulamiento 802.1Q a la VLAN 3 ROUTER1(config)#INTERFACE F0/0.3 ROUTER1(config-subif)#ENCAPSULATION DOT1Q 3 ROUTER1(config-subif)#IP ADDRESS 10.10.3.1 255.255.255.0 ROUTER1(config-subif)#EXIT PASO 2: CONFIGURAR PROTOCOLO VTP EN LOS SWITCHES CONFIGURACION SWITCH SERVIDOR Switch>ENABLE Switch#CONFIGURE TERMINAL Switch(config)#HOSTNAME SERVER

SERVER(config)#EXIT SERVER#VLAN DATABASE SERVER(vlan)#VTP SERVER SERVER(vlan)#VTP DOMAIN UDI SERVER(vlan)#VTP PASSWORD CISCO SERVER(vlan)#EXIT CONFIGURACION SWITCH CLIENTE Switch>ENABLE Switch#CONFIGURE TERMINAL Switch(config)#HOSTNAME CLIENTE1 CLIENTE1(config)#EXIT CLIENTE1#VLAN DATABASE CLIENTE1(vlan)#VTP CLIENT CLIENTE1(vlan)#VTP DOMAIN UDI CLIENTE1(vlan)#VTP PASSWORD CISCO CLIENTE1(vlan)#EXIT

CLIENTE1# PASO 3: CREAR VLANS EN EL SWITCH SERVER SERVER(config)#VLAN 1 SERVER(config-vlan)#NAME AMARILLA SERVER(config-vlan)#EXIT SERVER(config)#VLAN 2 SERVER(config-vlan)#NAME AZUL SERVER(config-vlan)#EXIT SERVER(config)#VLAN 3 SERVER(config-vlan)#NAME ROJA SERVER(config-vlan)#END PASO 4: CONFIGURAR PUERTOS TRUNKING

EN EL SWITCH SERVER SERVER(config)#INTERFACE F0/23 SERVER(config-if)#SWITCHPORT MODE TRUNK SERVER(config-if)#EXIT SERVER(config)# SERVER(config)#INTERFACE F0/24 SERVER(config-if)#SWITCHPORT MODE TRUNK SERVER(config-if)#EXIT SERVER(config)# EN EL SWITCH CLIENTE CLIENTE1(config)#INTERFACE F0/24 CLIENTE1(config-if)#SWITCHPORT MODE TRUNK CLIENTE1(config-if)#EXIT PASO 5: CONFIGURAR PUERTOS DE ACCESO

EN EL SWITCH SERVER SERVER(config)#INTERFACE F0/1 SERVER(config-if)#SWITCHPORT MODE ACCESS SERVER(config-if)#SWITCHPORT ACCESS VLAN 1 SERVER(config-if)#EXIT SERVER(config)#INTERFACE F0/2 SERVER(config-if)#SWITCHPORT MODE ACCESS SERVER(config-if)#SWITCHPORT ACCESS VLAN 2 SERVER(config-if)#EXIT SERVER(config)# EN EL SWITCH CLIENTE CLIENTE1(config)#INTERFACE F0/1 CLIENTE1(config-if)#SWITCHPORT MODE ACCESS CLIENTE1(config-if)#SWITCHPORT ACCESS VLAN 1

CLIENTE1(config-if)#EXIT CLIENTE1(config)#INTERFACE F0/2 CLIENTE1(config-if)#SWITCHPORT MODE ACCESS CLIENTE1(config-if)#SWITCHPORT ACCESS VLAN 2 CLIENTE1(config-if)#EXIT CLIENTE1(config)#INTERFACE F0/3 CLIENTE1(config-if)#SWITCHPORT MODE ACCESS CLIENTE1(config-if)#SWITCHPORT ACCESS VLAN 3 CLIENTE1(config-if)#EXIT CLIENTE1(config)# PASO 6: ASIGNAR IP A LOS SWITCH EN EL SWITCH SERVER SERVER(config)#INTERFACE VLAN1 SERVER(config-if)#IP ADDRESS 10.10.1.254 255.255.255.0

SERVER(config-if)#NO SHUTDOWN SERVER(config-if)#EXIT SERVER(config)# EN EL SWITCH CLIENTE CLIENTE1(config)#INTERFACE VLAN1 CLIENTE1(config-if)#IP ADDRESS 10.10.1.253 255.255.255.0 CLIENTE1(config-if)#NO SHUTDOWN CLIENTE1(config-if)#EXIT CLIENTE1(config)#

You might also like