OSHAX.

org - The Unofficial Guide To the OSHA

Introduction
Crushed hands and arms, severed fingers, blindness the list of possible machinery-related injuries is as long as it is horrifying. Safeguards are essential for protecting workers from needless and preventable injuries. A good rule to remember is: Any machine part, function, or process which may cause injury must be safeguarded. Where the operation of a machine can injure the operator or other workers, the hazard must be controlled or eliminated.

OSHAX.org - The Unofficial Guide To the OSHA

Causes of Machine Accidents

Reaching in to clear equipment Not using Lockout/Tagout Unauthorized persons doing maintenance or using the machines Missing or loose machine guards

OSHAX.org - The Unofficial Guide To the OSHA

Where Mechanical Hazards Occur

Point of operation All parts of the machine which move, such as: flywheels, pulleys, belts, couplings, chains, cranks, gears, etc. feed mechanisms and auxiliary parts of the machine In-running nip points

OSHAX.org - The Unofficial Guide To the OSHA

Point of Operation
That point where work is performed on the material, such as cutting, shaping, boring, or forming of stock must be guarded.

OSHAX.org - The Unofficial Guide To the OSHA

Rotating Parts

OSHAX.org - The Unofficial Guide To the OSHA

In-Running Nip Points

Rotating cylinders Belt and pulley

Chain and sprocket

Rack and pinion

OSHAX.org - The Unofficial Guide To the OSHA

Requirements for Safeguards

Prevent contact - prevent workers body or clothing from contacting hazardous moving parts Secure - firmly secured to machine and not easily removed Protect from falling objects - ensure that no objects can fall into moving parts Create no new hazards - must not have shear points, jagged edges or unfinished surfaces Create no interference - must not prevent worker from performing the job quickly and comfortably Allow safe lubrication - if possible, be able to lubricate the machine without removing the safeguards

OSHAX.org - The Unofficial Guide To the OSHA

Methods of Machine Safeguarding

Guards fixed interlocked adjustable self-adjusting Devices presence sensing pullback restraint safety controls (tripwire cable, two-hand contol, etc.) gates

Location/distance Feeding and ejection methods automatic and/or semiautomatic feed and ejection robots Miscellaneous aids awareness barriers protective shields hand-feeding tools

OSHAX.org - The Unofficial Guide To the OSHA

Fixed Guard
Provides a barrier - a permanent part of the machine, preferable to all other types of guards.

OSHAX.org - The Unofficial Guide To the OSHA

10

Interlocked Guard
When this type of guard is opened or removed, the tripping mechanism and/or power automatically shuts off or disengages, and the machine cannot cycle or be started until the guard is back in place. Interlocked guard on revolving drum

OSHAX.org - The Unofficial Guide To the OSHA

11

Adjustable Guard
Provides a barrier which may be adjusted to facilitate a variety of production operations.

Bandsaw blade adjustable guard

OSHAX.org - The Unofficial Guide To the OSHA

12

Self-Adjusting Guard
Provides a barrier which moves according to the size of the stock entering the danger area.
Circular table saw self-adjusting guard

OSHAX.org - The Unofficial Guide To the OSHA

13

Pullback Device

Utilizes a series of cables attached to the operators hands, wrists, and/or arms Primarily used on machines with stroking action Allows access to the point of operation when the slide/ram is up Withdraws hands when the slide/ram begins to descend

OSHAX.org - The Unofficial Guide To the OSHA

14

Pullback Device (contd)

Hands in die, feeding Point of operation exposed Pullback device attached and properly adjusted

Die closed Hands withdrawn from point of operation by pullback device

OSHAX.org - The Unofficial Guide To the OSHA

15

Restraint Device

Uses cables or straps attached to the operators hands and a fixed point Must be adjusted to let the operators hands travel within a predetermined safe area Hand-feeding tools are often necessary if the operation involves placing material into the danger area

OSHAX.org - The Unofficial Guide To the OSHA

16

Safety Tripwire Cables

Device located around the perimeter of or near the danger area Operator must be able to reach the cable to stop the machine

OSHAX.org - The Unofficial Guide To the OSHA

17

Two-Hand Control
Requires constant, concurrent pressure to activate the machine The operators hands are required to be at a safe location (on control buttons) and at a safe distance from the danger area while the machine completes its closing cycle

OSHAX.org - The Unofficial Guide To the OSHA

18

Gate

Movable barrier device which protects the operator at the point of operation before the machine cycle can be started If the gate does not fully close, machine will not function

Gate Open

Gate Closed
19

OSHAX.org - The Unofficial Guide To the OSHA

Safeguarding by Location/Distance

Locate the machine or its dangerous moving parts so that they are not accessible or do not present a hazard to a worker during normal operation Maintain a safe distance from the danger area

OSHAX.org - The Unofficial Guide To the OSHA

20

Automatic Feed
(shown on power press)
Transparent Enclosure Guard Stock Feed Roll

Danger Area

Completed Work

OSHAX.org - The Unofficial Guide To the OSHA

21

Robots

Machines that load and unload stock, assemble parts, transfer objects, or perform other tasks Best used in highproduction processes requiring repeated routines where they prevent other hazards to employees

OSHAX.org - The Unofficial Guide To the OSHA

22

Protective Shields
These do not give complete protection from machine hazards, but do provide some protection from flying particles, splashing cutting oils, or coolants.

OSHAX.org - The Unofficial Guide To the OSHA

23

Holding Tools
Used to place and remove stock in the danger area Not to be used instead of other machine safeguards, but as a supplement

OSHAX.org - The Unofficial Guide To the OSHA

24

Some Examples of OSHA Machine Guarding Requirements . . . .

OSHAX.org - The Unofficial Guide To the OSHA

25

Guarding Fan Blades

When the periphery of the blades of a fan is less than 7 feet above the floor or working level, the blades must be guarded with a guard having openings no larger than 1/2 inch.

OSHAX.org - The Unofficial Guide To the OSHA

26

Abrasive Wheel Machinery

Work rests on offhand grinding machines must be kept adjusted closely to the wheel with a maximum opening of 1/8-inch to prevent the work from being jammed between the wheel and the rest, which may result in wheel breakage.

OSHAX.org - The Unofficial Guide To the OSHA

27

Abrasive Wheel Machinery

The distance between the wheel periphery and the adjustable tongue must never exceed 1/4-inch.

OSHAX.org - The Unofficial Guide To the OSHA

28

Power-Transmission Apparatus
Power-transmission apparatus (shafting, flywheels, pulleys, belts, chain drives, etc.) less than 7 feet from the floor or working platform must be guarded.
Unguarded belt and pulley

OSHAX.org - The Unofficial Guide To the OSHA

29

Machine Safety Responsibilities Management

ensure all machinery is properly guarded

Supervisors
train employees on specific guard rules in their areas ensure machine guards remain in place and are functional immediately correct machine guard deficiencies

Employees
do not remove guards unless machine is locked and tagged report machine guard problems to supervisors immediately do not operate equipment unless guards are in place

OSHAX.org - The Unofficial Guide To the OSHA

30

Training
Operators should receive training on the following:

Hazards associated with particular machines How the safeguards provide protection and the hazards for which they are intended How and why to use the safeguards How and when safeguards can be removed and by whom What to do if a safeguard is damaged, missing, or unable to provide adequate protection

OSHAX.org - The Unofficial Guide To the OSHA

31

Summary

Safeguards are essential for protecting workers from needless and preventable machineryrelated injuries The point of operation, as well as all parts of the machine that move while the machine is working, must be safeguarded A good rule to remember is: Any machine part, function, or process which may cause injury must be safeguarded

OSHAX.org - The Unofficial Guide To the OSHA

32