TA8200AH

TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic

TA8200AH
Dual Audio Power Amplifier
The TA8200AH is dual audio power amplifier for consumer applications. This IC provides an output power of 13 watts per channel (at VCC = 28 V, f = 1 kHz, THD = 10%, RL = 8 ). It is suitable for power amplifier of TV and home stereo.

Features
High output power: Pout = 13 W/channel (Typ.) (VCC = 28 V, RL = 8 , f = 1 kHz, THD = 10%) Low noise: Vno = 0.14 mVrms (Typ.) (VCC = 28 V, RL = 8 , GV = 34dB, Rg = 10 k, BW = 20 Hz~20 kHz) Very few external parts Built in audio muting circuit Built in thermal shut down protector circuit Operating supply voltage range: VCC (opr) = 10~37 V (Ta = 25C) Weight: 4.04 g (typ.)

2002-02-13

TA8200AH
Block Diagram
VCC 6 Ripple Filter 9 VCC

IN1 IN1 4

AMP1 5 3 1

OUT1

7 RL

400 W Pre-GND 400 W

20 kW PW-GND 10 20 kW AMP2 12

RL OUT2

IN2

IN2

11

Application Information
1. Voltage gain
The closed loop voltage gain is determined by R1, R2. GV R + R2 = 20 log 1 (dB) R2
20 kW + 400 W = 20log = 34(dB) 400 W

Input 4/2 5/1 R2 400 W R1 20 kW 7/12

Output

= 34 (dB) Amplifier with gain < 34dB G V = 20 log R1 + R 2 + R 3 (dB) R2 + R3

Figure 1

When R3 = 220 W GV ~ - 30 (dB) is given.

Input 4/2 R3 5/1 R2 400 W R1 20 kW 7/12

Output

Figure 2

2002-02-13

TA8200AH
2. Muting
(1) Audio muting This IC is possible to make audio muting operation by using 11 pin muting terminal. In Fig. 3, the equivalent circuit in the muting circuit section is shown. By means of reducing the voltage of 11 pin down to 2.8 V or less in Fig. 3, Q1 is turned ON and the base voltage of Q2 in the differential circuit fabricated with Q2 and Q3. Therefore, with the voltage reduction of 11 pin, the input circuits of dummy of input terminal and that in the doted line operate and cut-off the input signal. After muting, the bias circuit continues is operation and the power supply current of quiescent time. 8 pin, the capacitor terminal for reducing the pop noise can reduce the pop noise through making the time constant longer by means of inserting the capacitor externary. In the care this terminal is not used, short 8 pin with 11 pin. The voltage of 11 pin set up to 4 V or more. IC internal muting at VCC OFF When VCC = 8 V or less at VCC off, the detection circuit at VCC off is operated. And the base voltage of Q1 is reduced and the muting operation is mode.

(2)

9 Reference voltage The detection circuit at VCC OFF Q1 100 W 1 kW Q2 Q3 I1 I2 I3 I4 I5 I6

VCC

Q6 D1 D2

Q4 Q5

20 kW

7/12 OUT

11 Mute

2/4 IN

Figure 3 Cautions
This IC is not proof enough against a strong E-M field by CRT which may cause malfunction such as leak. Please set the IC keeping the distance from CRT.

400 W 1/5 NF

2002-02-13

TA8200AH
Standard PCB

(Bottom view)

2002-02-13

TA8200AH
Maximum Ratings (Ta = 25C)
Characteristics Supply voltage Output current (Peak/ch) Power dissipation Operating temperature Storage temperature Symbol VCC IO (peak) PD (Note) Topr Tstg Rating 37 2.5 25 -20~75 -55~150 Unit V A W C C

Note: Derated above Ta = 25C in the proportion of 200 mW/C.

Electrical Characteristics
Characteristics Quiescent current Output power Total harmonic distortion Voltage gain Input resistance Ripple rejection ratio Output noise voltage Cross talk Muting threshold voltage

(unless otherwise specified, VCC = 28 V, RL = 8 9, Rg = 600 9, f = 1 kHz, Ta = 25C)

Symbol ICCQ Pout (1) Pout (2) THD GV RIN R.R. Vno C.T. Vth 11 Test Circuit Vin = 0 THD = 10% THD = 1% Pout = 2 W Vout = 0.775 Vrms (0dBm) Rg = 0, fripple = 100 Hz Vripple = 0.775 Vrms (0dBm) Rg = 10 kW, BW = 20 Hz~20 kHz Rg = 10 kW, Vout = 0.775 Vrms (0dBm) Test Condition Min 10 32.5 -40 2.6 Typ. 50 13 10 0.04 34.0 30 -50 0.14 -70 2.8 Max 105 0.2 35.5 0.3 Unit mA W % dB kW dB mVrms dB V

Typ. DC Voltage of Each Terminal (VCC = 28 V, Ta = 25C)

Terminal No. DC voltage (V) 1 1.6 2 20m 3 GND 4 20m 5 1.6 6 9.4 7 13.0 8 5.0 9 VCC 10 GND 11 2.8 12 13.0

2002-02-13

TA8200AH
Test Circuit
47 mF 1000 mF VCC

6 Ripple Filter IN1 2.2 mF 47 mF 47 mF 4 IN1 AMP1 5 3 1 400 W Pre-GND 400 W 20 kW AMP2 2.2 mF 2 IN2 20 kW

OUT1

2.2 W

1000 mF RL

PW-GND 10 2.2 W

0.12 mF 0.12 mF

RL

IN2

OUT2

12

1000 mF

8 *2

11 *1 Vth ~ - 2.8 V

*1: Mute on at 11 pin low Vth 11 = 2.8 V (typ.) (VCC = 28 V, Ta = 25C) *2: The capacitor for reducing POP noise at mute ON.

2002-02-13

TA8200AH

THD Pout
20

THD Pout
20

(%)

(%)

10 5 3

VCC = 28 V RL = 8 W

10 5 3

f = 1 kHz RL = 8 W

THD

THD

VCC = 22 V 28 1 0.5 0.3

37

Total harmonic distortion

1 0.5 0.3 f = 10 kHz 0.1 0.05 0.03 0.1 0.3 0.5 1 3 5 10 30 50 100 100 Hz 1 kHz

Total harmonic distortion

0.1 0.05 0.03 0 0.1

0.3 0.5

10

30 50

100

Output power

Pout

(W)

Output power

Pout

(W)

THD f
5 80 VCC = 28 V Pout = 1 W RL = 8 W 70 3

GV f
VCC = 28 V f = 1 kHz RL = 8 W

(%)

THD

Total harmonic distortion

0.3

Gv Voltage gain
30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k

0.5

(dB)

60 50 40 30 20 10

0.1 0.05 0.03

0.01

30 50 100

300 500 1k

3k 5k 10k

30k 50k 100k

Frequency f

(Hz)

Frequency f

(Hz)

R.R. f
0 -10 -20 -30 -40 -50 -60 -70 -80 VCC = 28 V RL = 8 W Rg = 0 W Vripple = 0.775 Vrms (0dBm) 0 -10 -20 -30 -40 -50 -60 -70 -80

R.R. Rg
VCC = 28 V RL = 8 W Vripple = 0.775 Vrms (0dBm) fripple = 100 Hz

Ripple rejection ratio R.R. (dB)

30 50 100

300 500 1k

3k 5k 10k

30k 50k 100k

Ripple rejection ratio R.R. (dB)

30 50 100

300 500 1k

3k 5k 10k

30k 50k 100k

Frequency f

(Hz)

Signal source resistance Rg (W)

2002-02-13

TA8200AH

C.T. f
0 -10 VCC = 28 V f = 1 kHz Vout = 0.775 Vrms (0dBm) RL = 8 W Rg = 10 kW 0 -10

C.T. Rg
VCC = 28 V f = 1 kHz RL = 8 W Vout = 0.775 Vrms (0dBm)

C.T. (dB)

-30 -40 -50 -60 -70 -80

C.T. (dB) Cross talk

-20

-20 -30 -40 -50 -60 -70 -80

Cross talk

30 50 100

300 500 1k

3k 5k 10k

30k 50k 100k

30 50 100

300 500 1k

3k 5k 10k

30k 50k 100k

Frequency f

(Hz)

Signal source resistance Rg (W)

Vno Rg
1.6 24 VCC = 28 V RL = 8 W f = 1 kHz RL = 8 W/4 W THD = 10 %

Pout VCC

(mVrms)

1.4 1.2 1.0 0.8 0.6 0.4 0.2 0

20

Pout (W) Output power

Output noise voltage

Vno

16

12 RL = 4 W 8 8

30 50 100

300 500 1k

3k 5k 10k

30k 50k 100k

0 10

14

18

22

26

30

34

38

42

Signal source resistance Rg (W)

Supply voltage VCC

(V)

ICCQ, VOUT VCC

240 Vin = 0 32 VCC = 28 V f = 1 kHz Pout = 2 W RL = 8 W DUAL Ope.

THD Ta
Heat sink 80 80 2 mm A (7C/W)

ICCQ (mA)

(V)

(%) Total harmonic distortion THD

0.2 0.1 0.05 0.03 0.01 -40

Quiescent current

120

16

VOUT 60 ICCQ 8

0 0

Output DC voltage VOUT

180

24

16

24

32

40

-20

20

40

60

80

100

Supply voltage VCC

(V)

Ambient temperature Ta (C)

2002-02-13

TA8200AH

ICCQ Ta
(mVrms)
80 Heat sink 80 80 2 mm A (7C/W) VCC = 28 V RL = 8 W 0.5

Vno Ta
Heat sink 80 80 2 mm A (7C/W) VCC = 28 V RL = 8 W Rg = 10 kW

ICCQ (mA)

70

0.4

50

Output noise volltage

Quiescent current

60

Vno
0.3 0.2 40 0.1 30 -40

-20

20

40

60

80

100

0 -40

-20

20

40

60

80

100

Ambient temperature Ta (C)

Ambient temperature Ta (C)

PD Pout
(W)
24 24

PD MAX VCC
f = 1kHz RL = 8 W

20

Maximum power dissipation PD MAX

32

(W)

VCC = 37 V

THD = 1% 10%

20

PD

16

16

Power dissipation

12

28 V 23 V f = 1kHz RL = 8 W DUAL OPE. 4 8 12 16 20 24 28

12

0 0

0 8

12

16

20

24

28

32

36

40

Output power

Pout (W)

Supply voltage VCC

(V)

PD MAX Ta
(W)
30 1: Infinite heat sink 25 1 2: 4.1C/W heat sink 3: 9.5C/W heat sink

Allowable power dissipation PD MAX

20 2 15 3

10

0 0

25

50

75

100

125

150

175

Ambient temperature Ta (C)

2002-02-13

TA8200AH
Package Dimensions

Weight: 4.04 g (typ.)

10

2002-02-13

TA8200AH

RESTRICTIONS ON PRODUCT USE

000707EBF

TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc.. The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (Unintended Usage). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customers own risk. This product generates heat during normal operation. However, substandard performance or malfunction may cause the product and its peripherals to reach abnormally high temperatures. The product is often the final stage (the external output stage) of a circuit. Substandard performance or malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the product. The products described in this document are subject to the foreign exchange and foreign trade laws. The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. The information contained herein is subject to change without notice.

11

2002-02-13

This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.