Scribd
Upload
23 views

Transistor Ce Characteristics (Input & Output)

1. The document describes an experiment to obtain the input and output characteristics of a transistor in a CE configuration. Key steps include varying the base-emitter voltage and collector-emitter voltage while measuring currents and voltages to plot the input and output graphs. 2. Readings would be recorded for input characteristics with the collector-emitter voltage held constant, and for output characteristics with the base current held constant. 3. The graphs and hybrid parameters including input impedance, output admittance, forward current gain, and reverse voltage gain would then be determined from the readings.

Uploaded by

Uday Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
23 views

Transistor Ce Characteristics (Input & Output)

1. The document describes an experiment to obtain the input and output characteristics of a transistor in a CE configuration. Key steps include varying the base-emitter voltage and collector-emitter voltage while measuring currents and voltages to plot the input and output graphs. 2. Readings would be recorded for input characteristics with the collector-emitter voltage held constant, and for output characteristics with the base current held constant. 3. The graphs and hybrid parameters including input impedance, output admittance, forward current gain, and reverse voltage gain would then be determined from the readings.

Uploaded by

Uday Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

www.jntuworld.

com
Exp. No.: Date :

www.jwjobs.net

TRANSISTOR CE CHARACTERISTICS (INPUT & OUTPUT)


AIM

: To obtain the input and output characteristics of a Transistor in CE


configuration and also determine the hybrid parameters.

APPARATUS :
S.No. Name of the Apparatus Range Quantity

1. 2. 3. 4. 5.

BC107 Power Supply Ammeter Voltmeter Resistor

0-30V 0-50A, 0-10mA 0-10V 100K

1No. 2No. Each 1No. 2No. 1No.

CIRCUIT DIAGRAM:`

0-50A +

100k

0-10mA A + BC107

IC

IB
+

VBB
0-30V

VBE 0-10V

+ -

VCE

+ -

Vcc
0-30V

0-10V -

PROCEDURE:

1. Connect the circuit as shown in figure. 2. For output characteristics Keep IB=10A by varying VBB. 3. Vary VCC in steps and note down IC and VCE. 4. Repeat step 3 for IB=20A and 30A 5. Draw the output characteristics by taking VCE on X-axis and IC on Y-axis for different values of IB. 6. For input characteristics Keep VCE=0, Vary VBB in steps and note down IB and VBE. 7. Repeat step 6 for VCE = 1V and VCE= 2V 8. Draw the input characteristics by taking VBE on X-axis and IB on Y-axis for different values of VCE.

www.jntuworld.com

www.jntuworld.com
Exp. No.: READINGS : a: Output Characteristics IB= 10A VCE (V) IC (mA) IB= 20A VCE (V) IC (mA) IB= 30A VCE (V) IC (mA) b: Input Characteristics VCE = 0V VBE (V) IB (mA) VCE = 1V VBE (V) IB (mA) VCE = 2V VBE (V) IB (mA) Date :

www.jwjobs.net

MODEL GRAPHS: Input Characteristics:

Output Characteristics: IC

IB

IB=30A IB=20A VCE=0 VCE=1V VCE=2V IB=10A

VBE

VCE

hie =

VBE = I B VCE cons tan t

h fe =

I C = I B VCE cons tan t

hre =

V BE = VCE I B cons tan t

hoe =

I C = VCB I B cons tan t

RESULTS:

1. Input Impedance, hie= 2. Output admittance, hoe= 3. Forward current gain, hfe= 4. Reverse voltage gain, hre=

www.jntuworld.com

You might also like