SolidCAM Milling Users Guide

Volume #1

1995-2004 SolidCAM LTD. All Rights Reserved.

Content

SolidCAM2005 Milling Users Guide

Contents
Volume #1 1. SolidCAM Basics 1.1 Installing SolidCAM software ...................................................................................................................14 1.1.1 System requirements ........................................................................................................................14 1.1.2 SolidCAM Single License Installation ...........................................................................................14 1.1.3 SolidCAM Network License Installation .....................................................................................19 1.1.4 SolidCAM Dongle Update .............................................................................................................21 1.2 Basics Concepts ..........................................................................................................................................22 1.3 Starting SolidCAM .....................................................................................................................................22 1.4 SolidCAM Interface ...................................................................................................................................23 1.5 Getting Help ................................................................................................................................................25 2. CAM-Part 2.1 Starting a new Milling CAM-Part .............................................................................................................28 2.1.1 The structure of the CAM-Part .....................................................................................................30 2.2 Dening Home ...........................................................................................................................................31 2.2.1 Multi-Sided Home ............................................................................................................................31 2.2.2 Dene Home.....................................................................................................................................32 2.2.3 Add Home within Multi-Sided Mode............................................................................................33 2.2.4 Dening the homes for 3-axis CNC machine within Multi-Sided mode ................................39 2.2.5 Dening the homes for 4-axis CNC machine within Multi-Sided mode ................................40 2.2.6 Dening the homes for 5-axis CNC machine within Multi-Sided mode ................................42 2.2.7 Home denition methods ...............................................................................................................44 2.2.8 Add Home within Projections Mode ............................................................................................46 2.2.9 Dening the homes for 3-axis CNC machine within Projected mode ....................................47 2.2.10 Dening the homes for 4-axis CNC machine within Projected mode ..................................49 2.2.11 Dening the homes for 5-axis CNC machine within Projected mode ..................................51 2.2.12 Home data dialog ...........................................................................................................................53 2.2.13 SolidCAM coordinate system .......................................................................................................55
3

SolidCAM2005 Milling Users Guide

Content

2.3 Home operations ........................................................................................................................................56 2.4 Stock and Target Model.............................................................................................................................58 2.4.1 Target model denition ...................................................................................................................60 2.4.2 Stock Model .......................................................................................................................................61 2.4.3 Updating Stock Model .....................................................................................................................65 2.5 Tool options ................................................................................................................................................67 2.6 Mac Options ................................................................................................................................................69 2.7 Work Material ..............................................................................................................................................70 2.8 CNC-Controller and Axis type .................................................................................................................71 2.8.1 Axis type.............................................................................................................................................71 2.9 Default G-Code numbers..........................................................................................................................74 2.10 Managing CAM-Parts ..............................................................................................................................76 2.11 CAM-Part Documentation .....................................................................................................................81 2.11.1 Documentation Editor ..................................................................................................................82 3. Tools 3.1 User-dened Tool Types ...........................................................................................................................86 3.1.1 Add new Tool Types ........................................................................................................................87 3.1.2 Delete Tool Types .............................................................................................................................88 3.2 Tool Tables ..................................................................................................................................................89 3.3 Working with Part Tool Table ..................................................................................................................90 3.4 Working with Current Tool Table ............................................................................................................91 3.5 Managing tool tables ..................................................................................................................................93 3.5.1 Edit Tool table ..................................................................................................................................93 3.5.2 Create Tool table ...............................................................................................................................94 3.5.3 Copy tool table ..................................................................................................................................95 3.5.4 Delete tool table ................................................................................................................................96 3.6 Tool Table dialog ........................................................................................................................................97 3.6.1 Tools Filter .........................................................................................................................................98 3.6.2 Tool Range .........................................................................................................................................99 3.6.3 Show Tool ...................................................................................................................................... 100
4

Content

SolidCAM2005 Milling Users Guide

3.6.4 Tool table - Edit ............................................................................................................................. 102 3.7 Managing tools ......................................................................................................................................... 103 3.8 Tool data ................................................................................................................................................... 108 3.8.1 Tool Type ....................................................................................................................................... 109 3.8.2 Topology page ................................................................................................................................ 110 3.8.3 Default tool data / Job Data ........................................................................................................ 115 3.9 Tool holding system ................................................................................................................................ 117 3.9.1 Tool holders dialog ........................................................................................................................ 118 3.9.2 Tool Holder Geometry denition ............................................................................................... 123 3.9.3 Tool Holder segments ................................................................................................................... 124 3.9.4 Using Tool Holders ....................................................................................................................... 126 3.10 Shaped Tools .......................................................................................................................................... 130 3.10.1 Shape-Tools dialog ...................................................................................................................... 131 3.10.2 Shape-tool geometry denition ................................................................................................. 135 3.10.3 Shaped Tool segments ................................................................................................................ 136 3.10.4 Using Shaped tools ...................................................................................................................... 138 3.11 Feed and Speed default ......................................................................................................................... 142 4. Geometry 4.1 Introduction ............................................................................................................................................. 148 4.2 Adding a new Geometry to your CAM-Part ....................................................................................... 149 4.3 Drill Geometry ......................................................................................................................................... 150 4.3.1 Dening a Drill Geometry ........................................................................................................... 150 4.3.2 Edit a Drill Geometry ................................................................................................................... 151 4.3.3 Drill Geometry Selection Dialog................................................................................................. 151 4.4 3D Model Geometry ............................................................................................................................... 156 4.4.1 Dening a 3D Model Geometry ................................................................................................. 156 4.4.2 Editing a 3D Model Geometry ................................................................................................... 158 4.4.3 CAD selection ................................................................................................................................ 159 4.5 Wireframe Geometry .............................................................................................................................. 160 4.5.1 Dening a Prole/Pocket Geometry ......................................................................................... 161

SolidCAM2005 Milling Users Guide

Content

4.5.2 Dening a Working Area .............................................................................................................. 162 4.5.3 Dening a Slot Geometry ............................................................................................................ 164 4.5.4 Dening a Section Geometry ...................................................................................................... 165 4.5.5 Dening a Limit Geometry ......................................................................................................... 167 4.6 Editing Chain Geometries...................................................................................................................... 169 4.6.1 Add Multi-chain ............................................................................................................................. 169 4.6.2 Adding a Chain .............................................................................................................................. 169 4.6.3 Chain operations ............................................................................................................................ 170 4.6.4 Settings ............................................................................................................................................ 171 4.6.5 Spline approximation .................................................................................................................... 171 4.7 Chain selection ......................................................................................................................................... 172 4.7.1 Chain Options dialog .................................................................................................................... 172 4.7.2 Chain selection dialog ................................................................................................................... 179 4.7.3 Chains direction ............................................................................................................................. 181 4.7.4 Chains sorting ................................................................................................................................ 183 4.8 Operations with Geometries ................................................................................................................. 186 4.8.1 Synchronization of the Wireframe geometry ........................................................................... 187 4.8.2 Synchronizaton of the 3D Model geometry ............................................................................. 192 5. Jobs 5.1 Adding a Job ............................................................................................................................................. 196 5.2 SolidCAM Job Interface ......................................................................................................................... 197 5.2.1 Home ............................................................................................................................................... 197 5.2.2 Geometry ........................................................................................................................................ 198 5.2.3 Tool .................................................................................................................................................. 199 5.2.4 Job name ......................................................................................................................................... 203 5.2.5 Milling Levels ................................................................................................................................. 204 5.2.6 Extra parameters ............................................................................................................................ 208 5.2.7 Mirror/Rotate point ...................................................................................................................... 208 5.2.8 Message ........................................................................................................................................... 209 5.2.9 Job operation buttons ................................................................................................................... 209 5.3 Working with Jobs ................................................................................................................................... 211 5.3.1 Add Job ........................................................................................................................................... 212
6

Content

SolidCAM2005 Milling Users Guide

5.3.2 Add Machining process ............................................................................................................... 213 5.3.3 Edit .................................................................................................................................................. 213 5.3.4 Calculate/Calculate All ................................................................................................................. 213 5.3.5 G-Code/G-Code All ..................................................................................................................... 213 5.3.6 Calculate & G-Code All ................................................................................................................ 213 5.3.7 Simulate ........................................................................................................................................... 213 5.3.8 File.................................................................................................................................................... 214 5.3.9 Job Group ....................................................................................................................................... 214 5.3.10 Delete/Delete all ......................................................................................................................... 215 5.4 Managing Jobs in the CAM-Manager tree ........................................................................................... 216 5.4.1 Job Sequence .................................................................................................................................. 216 5.4.2 Undo Sequence .............................................................................................................................. 216 5.4.3 Split .................................................................................................................................................. 216 5.4.4 Expand ............................................................................................................................................ 217 5.4.5 Collapse ........................................................................................................................................... 217 5.4.6 Automatic Sort ............................................................................................................................... 218 5.5 Job Transformations ............................................................................................................................... 219 5.5.1 Init .................................................................................................................................................... 220 5.5.2 Move ................................................................................................................................................ 220 5.5.3 Translate .......................................................................................................................................... 220 5.5.4 Rotate............................................................................................................................................... 222 5.5.5 Mirror .............................................................................................................................................. 223 5.5.6 4th Axis ........................................................................................................................................... 224 5.6 Fixture ....................................................................................................................................................... 225 5.6.1 Fixture dialog.................................................................................................................................. 226 6. 2.5D Milling 6.1 Prole Job ................................................................................................................................................. 230 6.1.1 Geometry name ............................................................................................................................. 231 6.1.2 Down Step ...................................................................................................................................... 232 6.1.3 Offsets ............................................................................................................................................. 232 6.1.4 Fillet size for last cut .................................................................................................................... 234 6.1.5 Dene depth................................................................................................................................... 235

SolidCAM2005 Milling Users Guide

Content

6.1.6 Descent type ................................................................................................................................... 237 6.1.7 Rest Material/Chamfer ................................................................................................................. 237 6.1.8 Tool Side ......................................................................................................................................... 243 6.1.9 Compensation ................................................................................................................................ 244 6.1.10 Prole Direction .......................................................................................................................... 246 6.1.11 Prole extension .......................................................................................................................... 246 6.1.12 Approach/Retreat ....................................................................................................................... 246 6.1.13 Trochoidal milling........................................................................................................................ 249 6.2 Pocket Job ................................................................................................................................................. 250 6.2.1 Geometry name ............................................................................................................................. 251 6.2.2 Down Step ...................................................................................................................................... 251 6.2.3 Pocket Types ................................................................................................................................... 252 6.2.4 Hatch type....................................................................................................................................... 253 6.2.5 Contour type .................................................................................................................................. 258 6.2.6 Hatch+Finish type......................................................................................................................... 266 6.2.7 Clear type ........................................................................................................................................ 267 6.2.8 Plunging Pattern ........................................................................................................................... 268 6.2.9 Overlap ............................................................................................................................................ 270 6.2.10 Compensation .............................................................................................................................. 270 6.2.11 Offsets ........................................................................................................................................... 270 6.2.12 Finish ............................................................................................................................................. 271 6.2.13 Fillet size for last cut .................................................................................................................. 272 6.2.14 Rest Material/Chamfer ............................................................................................................... 272 6.2.15 Approach ...................................................................................................................................... 272 6.2.16 Retreat ........................................................................................................................................... 276 6.3 Drill Job ..................................................................................................................................................... 279 6.3.1 Geometry name ............................................................................................................................. 280 6.3.2 Tool .................................................................................................................................................. 280 6.3.3 Drill depth ...................................................................................................................................... 280 6.3.4 Drill cycle type ............................................................................................................................... 281 6.3.5 Sequence of drill positions........................................................................................................... 284 6.4 Slot Job ...................................................................................................................................................... 286 6.4.1 Geometry name ............................................................................................................................. 287 6.4.2 Depth type ...................................................................................................................................... 287
8

Content

SolidCAM2005 Milling Users Guide

6.4.3 Constant Depth type ..................................................................................................................... 287 6.4.4 Section depth type ......................................................................................................................... 289 6.5 Translated Surface Job ............................................................................................................................ 293 6.5.1 Geometry name ............................................................................................................................. 294 6.5.2 Dene Prole Start Point ............................................................................................................. 295 6.5.3 Prole direction ............................................................................................................................. 295 6.5.4 Tool side .......................................................................................................................................... 295 6.5.5 Geometry on Section .................................................................................................................... 296 6.5.6 Constraint ....................................................................................................................................... 297 6.5.7 Process type .................................................................................................................................... 298 6.5.8 Surface Data for Translated Surfaces ......................................................................................... 298 6.5.9 Engraving Data for Translated Surface Job............................................................................... 301 6.5.10 Limits ............................................................................................................................................. 302 6.5.11 Limit Data for Translated Surface ............................................................................................ 303 6.5.12 Engraving Limit for Translated Surface Job ........................................................................... 306 6.5.13 Approach/Retreat ....................................................................................................................... 308 6.5.14 Show surface ................................................................................................................................ 308 7. 3D Milling 7.1 3D Model Job Overview ........................................................................................................................ 310 7.2 Working Area ........................................................................................................................................... 311 7.2.1 Working area dialog ....................................................................................................................... 312 7.2.2 Working area denition via Geometry ....................................................................................... 313 7.2.3 Working area denition via Surface condition .......................................................................... 316 7.2.4 Working area denition via Face selection ................................................................................ 317 7.2.5 Working area denition via Rest material .................................................................................. 319 7.3 Tolerance ................................................................................................................................................... 321 7.3.1 Surface tolerance ............................................................................................................................ 322 7.3.2 Tool path tolerance........................................................................................................................ 323 7.4 Roughing ................................................................................................................................................... 324 7.4.1 Overlap ............................................................................................................................................ 325 7.4.2 Down step ...................................................................................................................................... 325 7.4.3 Clean at ........................................................................................................................................ 325
9

SolidCAM2005 Milling Users Guide

Content

7.4.4 Offset............................................................................................................................................... 326 7.4.5 Fillet size for last cut .................................................................................................................... 327 7.4.7.Mode (Open Pocket machining) ................................................................................................. 334 7.4.8 Rest Material ................................................................................................................................... 337 7.4.9 Hatch Roughing ............................................................................................................................. 340 7.4.10 Contour Roughing ....................................................................................................................... 341 7.4.11 Plunging pattern .......................................................................................................................... 342 7.5 Semi-Finish/Finish .................................................................................................................................. 343 7.5.1 Overview ......................................................................................................................................... 343 7.5.2 Descent............................................................................................................................................ 346 7.5.3 Semi-Finish/Finish strategies ...................................................................................................... 349 7.5.4 Linear nish strategy ..................................................................................................................... 350 7.5.5 Offset cutting Finish Strategy ...................................................................................................... 356 7.5.6 Spiral Finish Strategy..................................................................................................................... 361 7.5.7 Circular Pocket Finish Strategy ................................................................................................... 368 7.5.8 Constant-Z Finish Strategy .......................................................................................................... 370 7.5.9 Pencil milling .................................................................................................................................. 380 7.6 3D Engraving Job .................................................................................................................................... 382 7.6.1 Geometry name ............................................................................................................................. 383 7.6.2 Engraving depth ............................................................................................................................ 383 7.6.3 Tolerance ......................................................................................................................................... 383 7.6.4 Engraving geometry name ........................................................................................................... 384 7.6.5 Engraving technology ................................................................................................................... 384 7.7 3D Drill Job .............................................................................................................................................. 387 7.7.1 Geometry name ............................................................................................................................. 388 7.7.2 Tool ................................................................................................................................................. 388 7.7.3 3D Model Geometry name .......................................................................................................... 388 7.7.4 Offset from model ........................................................................................................................ 389 7.7.5 Drill cycle type ............................................................................................................................... 389 7.7.6 Sequence of drill positions........................................................................................................... 390 8. Simulation 8.1 Introduction ............................................................................................................................................. 392

10

Content

SolidCAM2005 Milling Users Guide

8.1.1 Simulation modes .......................................................................................................................... 393 8.1.2 Simulation Controls....................................................................................................................... 393 8.2 2D simulation mode ................................................................................................................................ 394 8.2.1 Simulation Control ........................................................................................................................ 394 8.2.2 Simulation toolbar ......................................................................................................................... 394 8.2.3 Show Data....................................................................................................................................... 395 8.2.4 Projection ........................................................................................................................................ 395 8.2.5 Show tool ........................................................................................................................................ 397 8.2.6 Erase on Z change......................................................................................................................... 397 8.2.7 Stop on Next .................................................................................................................................. 397 8.2.8 Clear ................................................................................................................................................. 398 8.2.9 Colors .............................................................................................................................................. 398 8.2.10 Simulation speed .......................................................................................................................... 398 8.3 VerifyPlus simulation mode ................................................................................................................... 399 8.3.1 Simulation toolbar ......................................................................................................................... 399 8.3.2 Buttons available in the Setup Mode .......................................................................................... 401 8.3.3 Buttons available in the Simulation Mode ................................................................................. 403 8.4 Host CAD simulation mode .................................................................................................................. 404 8.4.1 Simulation Control ........................................................................................................................ 404 8.4.2 Show Data ..................................................................................................................................... 405 8.4.3 Show Tool ....................................................................................................................................... 405 8.4.4 Stop on Next .................................................................................................................................. 405 8.4.5 Clear ................................................................................................................................................. 405 8.4.6 Colors .............................................................................................................................................. 405 8.4.7 Simulation speed ............................................................................................................................ 405 8.5 3D simulation mode ................................................................................................................................ 406 8.5.1 Simulation toolbar ......................................................................................................................... 406 8.5.2 Simulation control ......................................................................................................................... 408 8.5.3 Show Data ..................................................................................................................................... 408 8.5.4 Stop on Next .................................................................................................................................. 408 8.5.5 Colors .............................................................................................................................................. 408 8.5.6 Simulation speed. ........................................................................................................................... 408 8.6 SolidVerify simulation mode .................................................................................................................. 409

11

SolidCAM2005 Milling Users Guide

Content

8.6.1 Simulation Control ........................................................................................................................ 409 8.6.2 Show Data ..................................................................................................................................... 409 8.6.3 Stop on Next .................................................................................................................................. 410 8.6.4 Clear ................................................................................................................................................. 410 8.6.5 Simulation speed ............................................................................................................................ 410 8.6.6 Single color/Color by tool ........................................................................................................... 410 8.6.7 Simulation toolbar ......................................................................................................................... 411 8.6.8 Simulation menu ............................................................................................................................ 417 8.7 Rest Material simulation mode .............................................................................................................. 420 8.7.1 Simulation toolbar ......................................................................................................................... 420 8.7.2 Simulation control ......................................................................................................................... 422 8.7.3 Tolerance ......................................................................................................................................... 423 9. G-Code 9.1 Generate .................................................................................................................................................... 426 9.2 List ............................................................................................................................................................. 427 9.3 Copy........................................................................................................................................................... 428 9.4 Print ........................................................................................................................................................... 428 10. SolidCAM Settings 10.1 Introduction ........................................................................................................................................... 430 10.2 User Directories Settings ...................................................................................................................... 431 10.2.1 User Directory for SolidCAM-Parts ......................................................................................... 431 10.2.2 User Directory for SolidCAM-Tables ...................................................................................... 432 10.3 Units Settings ......................................................................................................................................... 433 10.3.1 Metric/Inch .................................................................................................................................. 433 10.3.2 Approximation ............................................................................................................................. 434 10.3.3 Chain selection ............................................................................................................................. 434 10.3.4 Rest Material Calculation ............................................................................................................ 435 10.3.5 Fillet size for last cut ................................................................................................................... 435 10.4 Default CNC-controller settings ......................................................................................................... 436 10.4.1 Post-processor les directory .................................................................................................... 436

12

Content

SolidCAM2005 Milling Users Guide

10.4.2 CNC-controllers .......................................................................................................................... 437 10.5 Color Setup ............................................................................................................................................. 438 10.6 Auto-Save settings ................................................................................................................................. 440 10.7 External program settings .................................................................................................................... 441 10.8 Editors Settings ...................................................................................................................................... 442 10.9 DNC settings.......................................................................................................................................... 443 10.10 Simulation Settings .............................................................................................................................. 444 10.11 Synchronization settings..................................................................................................................... 445 10.12 Default Geometry Names.................................................................................................................. 447 10.13 Rest Materal & SolidVerify Settings.................................................................................................. 448 10.14 Tool Settings......................................................................................................................................... 450 Index ................................................................................................................................................................ 453

13

SolidCAM2005 Milling Users Guide

Content

14

SolidCAM Basics
SolidCAM is a powerful CAM product that has been especially designed for the shop floor. SolidCAM supports the complete range of major manufacturing applications including 2.5D Milling, 3D-Milling, Turning, Turning with Driven tools and Wire EDM, in one integrated solution. Machining operations can be defined on 2D Design Drawings as well as on 3D Solid and Surface Models. SolidCAM has also a powerful general post-processor tool that enables the easy customization of the G-Code file output to various types of CNC controllers This chapter discusses some basic concepts and terminology used throughout SolidCAM.

Installing SolidCAM Starting SolidCAM SolidCAM Basic concepts SolidCAM Interface Getting Help

SolidCAM2005 Milling Users Guide

1. SolidCAM Basics

1.1 Installing SolidCAM software

1.1.1 System requirements
Microsoft Windows XP Professional (recommended) with Service Pack 1, Windows 2000

(recommended) with Service Pack 3 or 4; also runs on Windows NT with Service Pack 6.

Intel Pentium- or AMD Athlon-class processor 256 MB RAM or more (512 MB or more recommended for large CAM-Parts machining) Graphics adapter ( 64MB RAM recommended) Pointing device CD-ROM drive Internet Explorer version 5.5 or later recommended

1.1.2 SolidCAM Single License Installation 1. Insert the SolidCAM Installation CD into the computers CD-ROM drive; the installation will be started automatically. You can also start the installation by running the setup.exe le. This le is located in the SolidCAMXXXX/Disk1 folder on the SolidCAM Installation CD. (XXXX is the current version of SolidCAM) 2. The Choose Setup Language dialog will be displayed.

Choose English language. When you have to install a localized version of SolidCAM, choose the appropriate language from the combo-box. The installation procedure will be continued.

16

1. SolidCAM Basics

SolidCAM2005 Milling Users Guide

3. The Installing SolidCAM dialog will be displayed. Click on the Next button.

4. The Choose Destination Location dialog will be displayed.

This dialog enables you to choose the destination folder for SolidCAM. You have to either conrm the default destination folder (C:\Program Files\SolidCAMXXXX) with the Next button or choose other destination folder with the Browse button and conrm it with the Next button.

17

SolidCAM2005 Milling Users Guide

1. SolidCAM Basics

5. The Select Components dialog will be displayed.

Choose the necessary SolidCAM component and conrm your choice with the Next button. Make a note that Program Files component can not be unselected.

6. The Select Program Folder dialog will be displayed.

Conrm the default Program Folder name - SolidCAMXXXX with the Next button. SolidCAM installation will be continued.

18

1. SolidCAM Basics

SolidCAM2005 Milling Users Guide

7. When the installation will be nished, the Choose language dialog will be displayed.

Choose English language and click on the OK button. When you install a localized version of SolidCAM, choose the appropriate language from the combo-box. 8. SolidCAM installs drivers for hardware dongle. When the drivers will be installed, the following message will be displayed.

Click on the OK button. 9. The Connection to CAD system dialog will be displayed. This dialog displays all CAD systems that can be used by SolidCAM.

Choose the appropriate Host-CAD systems for SolidCAM. When SolidCAM found only one CAD system available for connection, this dialog is not displayed. Click on the Next button.

19

SolidCAM2005 Milling Users Guide

1. SolidCAM Basics

SolidCAM will be connected to the dened CAD systems; the following message will be displayed.

Click on the OK button. 10.The following dialog will be displayed.

Click on the Finish button. The installation is nished.

20

1. SolidCAM Basics

SolidCAM2005 Milling Users Guide

1.1.3 SolidCAM Network License Installation SolidCAM enables you to install number of SolidCAM copies through your network. The SolidCAM Network Dongle have to be connected the server. The License Manager will be installed on the network server computer, which will distribute SolidCAM Licenses through client computers.
SolidCAM Network Dongle

SolidCAM License Server

lid CA M

M CA lid So

Lic

se en Lic

nse SolidCAM Lice

en se

So li

dC AM

li So AM dC Lic se en

L ic en

se

So

SolidCAM Client Computers

Check with which protocol is used for your network. SolidCAM enables you to use TCP/IP protocol (recommended) or IPX protocol. Install SolidCAM as explained above on the computer that will be used as SolidCAM License Server. TCP/IP Protocol 1. Open
..\SolidCAMXXXX\Util folder.

in

text

editor

the

NethaspTCPIP .ini

le

located

in

the

2. In the [NH_TCPIP] section edit the value of the NH_SERVER_ADDR parameters.

NH_SERVER_ADDR = xx.xx.xx.xx;

3. Type the IP address of the network server instead of xx.xx.xx.xx. 4. Rename the NethaspTCPIP.ini le to Nethasp.ini.
21

SolidCAM2005 Milling Users Guide

1. SolidCAM Basics

IPX Protocol Rename the NethaspIPX.ini le to Nethasp.ini. Installation of SolidCAM License Server 1. Connect the NetHASP dongle to the parallel port of the computer that will be used as SolidCAM License Server. 2. Run the Installation utility of the HASP dongle driver. Choose the Run option from the windows Start menu and type the following command in the Run dialog: <path for your SolidCAM folder>\Util\hinstall.exe i. The HASP device driver will be installed. Restart the computer. 3. Install the NetHASP License Manager - LMsetup.exe located in the ..\SolidCAMXXXX\Util folder. The NetHASP License Manager will be installed. 4. Activate the NetHASP License Manager. Choose the NetHASP License Manager / NetHASP License Manager command from the Programs menu. If the NetHASP License Manager already installed on your server you can use it and dont need to install another copy of the NetHASP License Manager. Installation of SolidCAM2004 on Client computers 1. Install SolidCAM on the client computer. 2. Copy
NETHASP .INI ..\SolidCAMXXXX\SolidCAM folder.

the

appropriate

le

from

the

server

to

the

3. Run SolidCAM.

22

1. SolidCAM Basics

SolidCAM2005 Milling Users Guide

1.1.4 SolidCAM Dongle Update In some cases SolidCAM requires the update of SolidCAM dongles. To update the dongle do the following steps: 1. Make sure that the SolidCAM dongle is connected to the computer. 2. Extract the ZIP-archive <dongle number>.zip supplied by SolidCAM into the ..\SolidCAMXXXX\Util folder 3. Extract the ZIP-archive customer.zip to the same folder. 4. Run the Mak_plag.bat le located in the ..\SolidCAMXXXX\Util folder. It is recommended to run it with the Command Prompt (Start > Programs > Accessories) window. When the Command prompt dialog is displayed enter the following commands:
Cd <full path for SolidCAM folder>\Util Mak_plag

By default, the full path for SolidCAM folder is the following:

c:\Program Files\SolidCAMXXXX

5. The message: Hasp Memory updated OK will be displayed.

23

SolidCAM2005 Milling Users Guide

1. SolidCAM Basics

1.2 Basics Concepts

Every manufacturing project in SolidCAM contains the following data:
CAM-Part - The CAM-Part denes the general data of the workpiece. This includes the mo-

del name, the home position, tool options, CNC-controller etc...

Geometry - By selecting Edges, Curves, Surfaces or Solids, dene WHAT and WHERE you

are going to machine. This geometry is associated with the native SolidWorks model. rameters and Strategies are dened - in short HOW you want to machine.

Job - A Job is a single machining operation in SolidCAM. In the Job Technology, Tool pa-

1.3 Starting SolidCAM

To activate SolidCAM, simply click on the eld SolidCAM in the main menu of SolidWorks and choose Milling from the New sub-menu. SolidCAM will be started.

24

1. SolidCAM Basics

SolidCAM2005 Milling Users Guide

1.4 SolidCAM Interface

After the CAM-Part is loaded, the SolidCAM Manager will be displayed in the left part of the screen. SolidWorks window

CAM Views Toolbar Home Position

SolidCAM Manager

Machining Solid Model

The SolidCAM Manager is the main interface feature of SolidCAM. Complete information about the CAM-Part is shown in the SolidCAM Manager. CAM-Part Header Tool Header Machining Processes Header Geometries Header Jobs Header Jobs

25

SolidCAM2005 Milling Users Guide

1. SolidCAM Basics

The SolidCAM Manager contains the following elds:

CAM-part field

This eld displays the name of the active SolidCAM CAM-Part. By right clicking on it, you can activate the CAM-Part menu to manage your CAM-Parts. For more information on CAM-Parts, please refer to Chapter 2.
Tool field

This eld displays the name of the active Tool Table. By right clicking on it, you can activate the menu to manage the Tool Tables. For more information on Tools, please refer to Chapter 3.
Machining Process field

This eld displays the name of the active Machining Process Table. By right clicking on it, you can activate the menu to manage the MP Tables. For more information on Machining Processes, please refer to the Chapter 11.
Geometries field

This eld displays all the SolidCAM geometries not used in the Jobs. You can get the list of these geometries by clicking on the + icon near the Geometries eld. You can display the Geometries managing menu by right clicking on the Geometries eld. You can also get the relevant menu by right clicking on each Geometry name. For more information on Geometries, please refer to Chapter 4.
Jobs field

This eld shows you all the SolidCAM Jobs. The Jobs managing menu is available by right clicking on the Jobs eld. You can get the relevant menu also by right clicking on each Job name.
Home position
Chapter 5.

For more information on Jobs, please refer to

Home position The Home position is shown on the model. It denes the origin for all the machining operations of the CAMPart. For more information on Homes, please refer to the topic 2.2.
26

1. SolidCAM Basics

SolidCAM2005 Milling Users Guide

1.5 Getting Help

The SolidCAM On-Line Help enables you to get on-line help about different options in SolidCAM. This help is installed in the .../Documentation folder after the standard installation procedure. This Help is available via the SolidWorks Help menu. Click on the Help item in the main menu of SolidWorks and choose the SolidCAM Help -> Milling items from the submenu.

SolidCAM Help is fully context sensitive. You can get specic Help topic for the each SolidCAM dialog by pressing the F1 button. To get information about a specic dialog area like eld, button etc... you have to click on the question-mark in the upper-right corner of the dialog and then click on the eld or button you need. The On-Line Help will be displayed and then the specic topic will be explained. The Machining Portfolio is also available in the .../Documentation folder. This document provides an overview of the various features of SolidCAM.

27

SolidCAM2005 Milling Users Guide

1. SolidCAM Basics

28

CAM-Part
In the CAM-Part you have to specify all the information relevant to the machining project or workpiece you want to manufacture. The CAMPart folder will include all machining geometries, job definitions and generated G-Code files. The parameters and values defined at the CAM-Part level, such as Home position, Milling levels and Tools will serve as default values for the separate machining operations. All specified parameters can be changed in single operations (jobs).

Starting a new Milling CAM-Part Managing CAM-Parts Defining a Home Defining Stock Model Defining Target Model CAM-Part Documentation

SolidCAM2005 Milling Users Guide

2. CAM-Part

2.1 Starting a new Milling CAM-Part

When the SolidWorks Part is loaded SolidCAM Manager is loaded, do the following:

1. Click on the SolidCAM item in the SolidWorks menu. The SolidCAM main menu will be displayed. 2. Choose the New option from the menu to dene a new CAM-Part. 3. Choose the type of new CAM-Part - Milling from the submenu. 4. The CAM-Part data dialog will be displayed. When you start to program a CAM-Part, you have to decide on: What type of CNC machine you are going to use? (3, 4 or 5 axis). Where are you going to clamp this part? Where are your main home positions? (On a 4 or 5 axis CNC machine every clamping position is the main home to which all additional positioning are related). In the CAM-Part you have to specify all the information relevant to the machining project or workpiece you want to manufacture. The parameters and values dened at the CAM-Part level will serve as default values for machining levels, etc. Naturally, all parameters can be changed in single machining operations (jobs).

30

2. CAM-Part

SolidCAM2005 Milling Users Guide

When you create a new CAM-Part, you have to enter a name for the CAM-Part and the model that contains the CAM-Parts geometry.
Directory

Specify the location of the CAM-Part. The default directory is the SolidCAM user directory (dened in the SolidCAM Settings). You can enter the path or use the Browse button to dene the location.
CAM-Part name

Enter the name of the CAM-Part. You can give any name to identify your machining project. By default SolidCAM uses the name of the design model.
Model name

This eld shows the name and location of the SolidWorks design model that you are using for the CAM-Part denition. The name is, by default, the name of the active SolidWorks document. With the Browse button you can choose any other SolidWorks document to dene the CAM-Part. In this case the chosen SolidWorks document will be loaded into SolidWorks. Every time the CAM-Part is opened, SolidCAM automatically checks the correspondence of the dates of the CAM-Part and the original SolidWorks design model. When the date of the original SolidWorks model is later than the date of the CAM-Part creation, this means that the SolidWorks original model has been updated. You can then replace the SolidWorks design model on which the CAMPart is based with the updated SolidWorks design model.
31

SolidCAM2005 Milling Users Guide

2. CAM-Part

After the Directory, CAM-Part name and Model name are dened, click on the OK button to conrm the CAM-Part creation. The CAM-Part will be dened and its structure will be created. 2.1.1 The structure of the CAM-Part The CAM-Part includes the following data (e.g. for a CAM-Part whose name is Cavity): A le Cavity.prt is located in the SolidCAM User directory. A subdirectory Cavity containing all the data generated for the CAM-Part.

SolidCAM copies the original SolidWorks model to the subdirectory Cavity and creates a SolidWorks assembly that has the same name as the CAM-part (Cavity.sldasm). There are two components in this assembly:
DesignModel.sldprt CAM.sldprt

copy of the SolidWorks model le.

- contains SolidCAM home and geometry data.

SolidCAM CAM-Part uses the assembly environment of SolidWorks. This enables you to create auxiliary geometries (e.g. sketches) without making changes in the original design model. You can also insert some additional components into the assembly le such as stock model, CNC machine table, clamping and other tooling elements.

32

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.2 Defining Home

2.2.1 Multi-Sided Home This mode enables you to create CAM-Part dened directly on the solid model. You can dene the home origin position and axes orientation by choosing points on the solid model or by selecting an already dened SolidWorks coordinate system.

Y Direction

X Direction

Home Origin

33

SolidCAM2005 Milling Users Guide

2. CAM-Part

If this option is not chosen (Projections mode) SolidCAM enables you to create the CAM-Part on planar views dened by 2D sketches on the XY plane. In most cases this mode will be used when importing a DXF or IGES le and when you do not want to create a solid model.

You can use this mode to create 3-, 4-, or 5-axis CAM-parts. After dening the main home on the XY-plane of SolidWorks, you must use the Home Data dialog to manually dene the shifts and rotations of the additional positionings, from the main home. 2.2.2 Define Home The Home position denes the origin for all machining operations of the CAM-Part. You can create multiple home positions and in each machining step select which home you want to use for the job. To complete the CAM-Part menu, you must enter the home position. Click on the Home button in the CAM-Part Data dialog. If you dene the rst home in the current CAM-Part, the Home dialog will be displayed depending on your Multi-Sided Home settings.
Home

Projections Mode

Multi-Sided Mode

If the Home that you dene is not the rst, the Home Edit dialog (see the topic 2.3. ) will be displayed. This dialog enables you to manage your Homes.

34

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.2.3 Add Home within Multi-Sided Mode This mode enables you to dene a new 3-4-5 axis home directly on the solid model. The newly created home will automatically receive the next sequential number.

Mac home number this number corresponds with the built-in controller Home functions (example: G54, G55 etc in the Fanuc type controllers). It can be used for different clamping positions (main homes) in different operations on the CAM-Part. Position this number denes the sequence number of the home. For each MAC Home (main home) , several Positions are dened for different positionings; each such Position is related to the main Home. In multi-sided machining on 4- and 5-axis CNC machines, the SolidCAM postprocessor uses the specic controller Macro language to create the positioning relative to the main home. When you change the Mac home number to a new number in a 4-axis CNC machine, you have to dene 3 points: Origin /X direction/ Y direction. If there are two or more CAM-Part home numbers dened on this Mac home, you will have to dene only the Origin and a point on the plane to rotate to; the rotation axis is dened by the type of the 4-axis (_4th_axes_around = X / Y in the Mac le).

35

SolidCAM2005 Milling Users Guide

2. CAM-Part

SolidCAM enables you to dene the Home by one of the three methods:
Select Face Define Coordinate system

Select Face SolidCAM enables you to dene a new Home by selecting a face. The face can be one of the following:
Planar face

In this case the Z-axis of the Home will be normal to the face.

Cylindrical/Conical face

In this case the Z-axis of the Home will be parallel to the axis of the revolution of the specied cylindrical/conical face.

36

2. CAM-Part

SolidCAM2005 Milling Users Guide

Pick Face

This button enables you to select the face on the model for the Home denition. The selected model face will be higlighted.
Change to opposite/Change to original

This button enables you to change the direction of the Z-axis of the home to the opposite direction.
Place home origin to: Corner of Model Box

In this case the box surrounding the model will be calculated.

The upper plane of the model box is parallel to the XY-plane of the dened Home. The Home Position will be located in the corner of the model box with the following coordinates (XMIN, YMIN, ZMAX).

37

SolidCAM2005 Milling Users Guide

2. CAM-Part

Center of Revolution Face

The origin will be located at the intersection of the rotation axis of the part and the face of the model box with a maximal Z coordinate (the Z-axis is directed along the rotation axis).

Home #1

The Home origin will be in the same location of the Home #1 origin. This option is active only if the rst Home is already dened.

38

2. CAM-Part

SolidCAM2005 Milling Users Guide

Define

Origin

Select the origin point on the graphic screen. Select a point relative to the origin that denes the X-axis.

X direction

Y direction Select a point (3rd point) that denes the plane. (The Y-axis will be 90 degrees to the X-axis; the selected point denes the plane). Pick Origin - This option enables you to dene a new location for the Home Origin. The axis direction

will not be changed.

Pick X direction -

This option enables you to choose a new direction for the X-axis. After a point is selected, the next button is automatically activated. If you miss the selection, you can, at any time, select the button you want to dene and continue automatically to the next button.

39

SolidCAM2005 Milling Users Guide

2. CAM-Part

Select coordinate system

SolidCAM enables you to choose the coordinate system dened in the CAD model le as the home. Flip SolidCAM enables you to ip the dened Home.
Flip XY

Pushing this button will rotate the Z-axis 180 degrees by replacing the X and Y between themselves (X becomes Y and Y becomes X).
Flip X

This button rotates the Home 180 degrees around the X axis.
Flip Y

This button rotates the Home 180 degrees around the Y axis.
40

2. CAM-Part

SolidCAM2005 Milling Users Guide

Finish Pushing this button will add the home to the CAM-Part; the Home data dialog will be displayed. 2.2.4 Defining the homes for 3-axis CNC machine within Multi-Sided mode During the Home denition for 3-axis CNC machine you have to dene three points with the Home dialog. Origin Select the origin point on the graphic screen. X direction Select a point relative to the origin that denes the X-axis. Y direction Select a point (3rd point) to nish the denition of the XY-plane. Use the mouse to dene the origin, X and Y direction. You dont have to click on the X direction or the Y direction buttons in the Home dialog; they will be automatically selected after you dene a point.

Y Direction (third point)

X Direction (second point)

Home Origin (rst point)

Home definition

Clamping

For the next home position you also have to dene three points.

41

SolidCAM2005 Milling Users Guide

2. CAM-Part

Y Direction (third point)

X Direction (second point)

Home Origin (rst point)

Home definition

Clamping

SolidCAM automatically assigns the new Part Home number for the each Home; the Mac home number can be changed by user for a new clamping (main home position). 2.2.5 Defining the homes for 4-axis CNC machine within Multi-Sided mode When you dene the main home position (Mac Home) for the 4-axis CNC-machine you have to dene three points with Home dialog: Origin Select the origin point on the graphic screen. X direction Select a point relative to the origin that denes the X-axis. Y direction Select a point (3rd point) to nish the denition of the XY-plane. Use the mouse to dene the origin, X and Y direction. You dont have to click on the X direction or the Y direction buttons in the Home dialog; they will be automatically selected after you dene a point.

42

2. CAM-Part

SolidCAM2005 Milling Users Guide

Y Direction (third point)

X Direction (second point)

Home Origin (rst point)

Home definition

Clamping

To add a new Part Home you have to dene only two points: The point for the Home origin. Point on the plane to rotate to. If the rotation axis is X, you have to dene the Y direction. If the rotation axis is Y, you have to dene the X direction.

Y Direction (second point)

X Direction (determined automatically)

Home Origin (rst point)

Home definition

Clamping

SolidCAM automatically assigns the new Part Home number for the each Home; the Mac home number can be changed by user for a new clamping (main home position).

43

SolidCAM2005 Milling Users Guide

2. CAM-Part

The rotation axis is dened automatically by SolidCAM according to the Axis type (see the topic 2.8). The Shift and Rotation around parameters will be calculated automatically. 2.2.6 Defining the homes for 5-axis CNC machine within Multi-Sided mode When you dene the main home position (Mac Home) for the 4-axis CNC-machine you have to dene three points with Home dialog: Origin - Select the origin point on the graphic screen. X direction - Select a point relative to the origin that denes the X-axis. Y direction - Select a point (3rd point) to nish the denition of the XY-plane. Use the mouse to dene the origin, X and Y direction. You dont have to click on the X direction or the Y direction buttons in the Home dialog; they will be automatically selected after you dene a point.

Y Direction (third point)

X Direction (second point)

Home Origin (rst point)

Home definition

Clamping

To add a new Part Home you have to dene three points.

44

2. CAM-Part

SolidCAM2005 Milling Users Guide

Y Direction (third point)

X Direction (second point)

Home Origin (rst point)

Home definition

Clamping

SolidCAM automatically assigns the new Part Home number for the each Home; the Mac home number can be changed by user for a new clamping (main home position).
2.8)

The rotation axis is dened automatically by SolidCAM according to the Axis type. (see the topic

The Shift and Rotation around parameters will be calculated automatically.

45

SolidCAM2005 Milling Users Guide

2. CAM-Part

2.2.7 Home definition methods Home definition using a sketch In some cases you cannot dene the Home origin position or the direction of the axes without adding a geometry.

In this case you have to create a sketch that contains two perpendicular lines; the intersection point of the lines will dene the Home origin and the lines dene the X- and Y-axis directions.

46

2. CAM-Part

SolidCAM2005 Milling Users Guide

Choose the origin location at the intersection point of the lines and dene the axis direction.

Y direction Home Origin

X direction

Home definition using a stock box SolidCAM enables you to automatically generate the stock box surrounding the model with a dened offset. (see the topic 2.4.2) The top stock plane will be parallel to the XY plane of the machine coordinate system.

Dene the Home in the stock box corner.

47

SolidCAM2005 Milling Users Guide

2. CAM-Part

Sometimes the model is located in the assembly in such a way that you need to rotate it before using the Stock by box option in order to enable SolidCAM to calculate the optimal stock.

2.2.8 Add Home within Projections Mode We will use this method for imported DXF or 2D IGES les. In this exercise the way to work with this mode on 2D sketches of the working views will be explained. You can use this method for solids only if you are going to mill only from 1 direction and the orientation of the solid is exactly like in the milling position. In the Projections mode you have to use a lot of imagination and knowledge in the multi-axial positioning in order to dene the correct coordinate for the Home positions. 1. Dene Mac home number the machine home number that has to be set in the CNC controller (Home #1 = G54).

Mac home number this number corresponds with the built-in controller Home functions (example: G54, G55 etc in the Fanuc type controllers). It can be used for different clamping positions (main homes) in different operations on the CAM-Part. Position this number denes the sequence number of the home. For each MAC Home (main home), several Positions are dened for different positionings; each such Position is related to the main Home. 2. Pick home position - Pick a point - or enter the X, Y, Z coordinate values of the CAM-Parts home position into the Edit bar and conrm by clicking on Enter.

3. After you have entered the home position, you have to dene the tool movement and material levels i.e. planes. The Home data dialog will be displayed. You can either enter the Z-level values or you can select the values from your model after clicking on the respective buttons. 4. Conrm and close the dialog by clicking the OK button.
48

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.2.9 Defining the homes for 3-axis CNC machine within Projected mode During the Home denition for 3-axis CNC machine you have to dene one point for the home origin with the Home dialog. The point have to be dened on the top plane of the model in the orientation that will be used for machining. The X and Y axis direction will be determined automatically.

Y Direction

X Direction

Home #1

Home #1

49

SolidCAM2005 Milling Users Guide

2. CAM-Part

For the next home position you also have to dene an origin point.

X Direction

Y Direction

Home #2

Home #2

SolidCAM automatically assigns the new Part Home number for the each Home; the Mac home number can be changed by user for a new clamping (main home position).

50

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.2.10 Defining the homes for 4-axis CNC machine within Projected mode During the Home denition for 4-axis CNC machine you have to dene one point for the home origin with the Home dialog. The point have to be dened on the top plane of the model in the orientation that will be used for machining. The X and Y axis direction will be determined automatically.

Y Direction

X Direction

Home #1

Home #1

51

SolidCAM2005 Milling Users Guide

2. CAM-Part

To add a new Part Home you have to dene the point for the Home origin.

X Direction

Y Direction

Home #2

Home #2

SolidCAM automatically assigns the new Part Home number for the each Home; the Mac home number can be changed by user for a new clamping (main home position). You have to dene the Shift and Rotation around parameters describing position and orientation of the new Part Home according to the Mac Home.

52

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.2.11 Defining the homes for 5-axis CNC machine within Projected mode During the Home denition for 5-axis CNC machine you have to dene one point for the home origin with the Home dialog. The point have to be dened on the top plane of the model in the orientation that will be used for machining. The X and Y axis direction will be determined automatically.
X Direction Y Direction

Home #1
Home Origin

53

SolidCAM2005 Milling Users Guide

2. CAM-Part

To add a new Part Home you have to dene the point for the Home origin.

Y Direction

X Direction

Home #2

Home #2

SolidCAM automatically assigns the new Part Home number for the each Home; the Mac home number can be changed by user for a new clamping (main home position). You have to dene the Shift and Rotation around parameters describing position and orientation of the new Part Home according to the Mac Home.

54

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.2.12 Home data dialog Below is an explanation of the elds of the Home data dialog.

Position denes the sequence number of the home. For each Machine Home, several Positions are dened for different positionings; each such Position is related to the main Home. X shows the X-value of the Home. Y shows the Y-value of the Home. Z shows the Z-value of the Home. Machine home number denes the number of the home in the CNC-Machine. The default value is 1. If you use another number, the G-Code le will contain the G-function that tells the machine to use the specied number stored in the machine controller of your machine. The Tool start level denes the Z-level at which the tool will start. The Clearance level is the Z-level to which the tool rapids when moving from one job to another (in case the tool did not change). CAM-Part Upper level denes the height of the upper surface of the part to be milled. CAM-Part Lower level denes the lower surface level of the part to be milled.

55

SolidCAM2005 Milling Users Guide

2. CAM-Part

Tool Z Level is the height that the tool moves to before the rotation of the 4/5 axes to avoid collision between the tool and the workpiece. This level is related to the home position and you have to check if it is not over the limit switch of the machine. It is highly recommended to send the tool to the reference point or to a point related to the reference point.

Tool Start level Rapid Movements area Clearance level Feed Movements area

Part Upper level

Part Lower level

Shift is the distance from the main home (Mac home) to the location of this home in the coordinate system and the orientation of the main home. Rotation is the rotation angle around the main axes X, Y and Z. For the rst Part Home number related to a new Mac Home number, the Shift and Rotation around parameters will be always 0. Shift and Rotation for other Part Home Numbers related to the same Mac Home number will be determined automatically within Multi-Sided mode. Within Projections mode the Shift and Rotation values must be dened manually. The 4-th axis eld can be either On or Off. Click the mouse on this eld to choose On. The 4th-Axis will then be used when changing from the previous home to the current home. The Machining Plane denes the default plane of work for the jobs using this home, as it is output to the G-Code program. In the SolidCAM CAM module, you must always work on the XY-plane. Some CNC-machines, however, have different axes-denitions and require G-Code output with rotated XYplanes. Choose one of the following options: XY - The XY plane is the work plane; the Z-axis is the depth (G17). YZ - The YZ plane is the work plane; the X-axis is the depth (G18). XZ - The XZ plane is the work plane; the Y-axis is the depth (G19).

56

2. CAM-Part

SolidCAM2005 Milling Users Guide

This option will only work correctly when your post-processor has been customized to support this function. Please contact customer support for further details.
Edit 4-5-Axis Home

This button enables you to change the home location or orientation of axis with the Home 4-5 Axis dialog.

2.2.13 SolidCAM coordinate system SolidCAM changes the model orientation by setting the model to the Machine Isometric view. This orientation is suitable for machining on a CNC machine (with the Z-axis pointing vertically upwards).

Z Y

Z
SolidWorks Coordinate system

X
SolidCAM Coordinate system

Use the CAM Views toolbar to see the SolidCAM coordinate system. These views are related to the orientation of the selected home position.

57

SolidCAM2005 Milling Users Guide

2. CAM-Part

2.3 Home operations

The Home commands are available in the CAM-Part Data dialog after the rst Home is dened. The Home Edit dialog will be displayed after selecting the Define Home button.

1. Right click on the Home name in the Home Edit dialog. The pulldown menu will be displayed.

2. Choose the specic command from the menu. Add Home This commands enables you to add a new home to the current CAM-Part. Edit Home This command enables you to change the data of an existing home. It also enables you to change the home position. 1. Pick home - Choose the home you want to edit. 2. The Home data dialog box will be displayed showing the default home position values. The elds and values can be changed, if necessary.
58

2. CAM-Part

SolidCAM2005 Milling Users Guide

If you change the home position, you must recalculate the jobs using this home position. You are also advised to review the simulation.

Move Home This button enables you to move the actual Home. This option is disabled in the Multi-sided mode. 1. Pick home - Choose the home you want to move. 2. Pick new home position - Pick a point for the new origin. Inquire Home In the Inquire Home eld you can view the relevant information about a particular home position but you cannot change anything.

59

SolidCAM2005 Milling Users Guide

2. CAM-Part

Delete Home Deletes an existing home. You can only delete homes if more than one home has been dened for the current CAM-Part. It is not possible to delete the rst home and a home that is used for the milling operation. (The Delete item in the menu will be disabled in these cases). 1. Pick home - Choose the home you want to delete. A conrmation message will be displayed.

2. Choose Yes to conrm.

2.4 Stock and Target Model

Stock model -

the material that is placed on the machine before you start machining the CAM-Part.

The Stock model is used for: Solid Verify and VerifyPlus simulation. For rest material calculation in 3D jobs, in case the eld Update Stock model is checked. The stock model is not automatically associated with the solid model. If the model is changed and the stock is not correct anymore you will see it in the simulation; you can then replace the dened stock with the updated one.

60

2. CAM-Part

SolidCAM2005 Milling Users Guide

Target model

- the nal shape of the CAM-Part after the machining.

SolidCAM will use the Target model for: 3D simulation Rest material calculation Gouge checking in SolidVerify simulation. During all machining operations, the rest material that is left is removed in order to reach the Target model.

61

SolidCAM2005 Milling Users Guide

2. CAM-Part

If the small square is unchecked, no stock & target models have been dened.

If the small square is checked, the stock & target models have been dened.

2.4.1 Target model definition The Target model option enables you to dene the nal part after machining.

1. Click on the Target model button in the CAM-Part data dialog 2. Click on the Define 3D model button to start the geometry selection. 3. Select the geometry with the 3D geometry dialog (see the topic 4.4.1). 4. After the geometry selection you will be prompted to enter the target model name. Enter a name and click on the OK button. In future 3D operations you can use the Target material as the dened geometry.

62

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.4.2 Stock Model The Stock model option enables you to see the actual material that has to be removed.

1. Click on the Stock model button in the CAM-Part Data dialog. 2. Choose the stock model denition mode and click on the Define button. 3. Select the geometry. 4. After geometry selection you will be prompted to enter the stock model name. Enter a name and click on the OK button.

Modes 2D Boundary - this mode enables you to dene the 2D stock geometry with the chain of the geometry elements (lines, arcs, splines, edges... etc). Before choosing the stock material, you rst have to draw the boundaries of the stock material around the CAM-Part. After choosing this mode and pressing the dene button, the Geometry Edit dialog will be displayed.

63

SolidCAM2005 Milling Users Guide

2. CAM-Part

3D Model - this option enables you to dene the stock model via 3D model selection. This option is useful for casting machining. After choosing this mode and pressing the dene button, the 3D geometry dialog will be displayed.

Box (Auto) - In this case SolidCAM automatically nds the box surrounding the model. After pressing the Define button, the 3D Box dialog will be displayed. The 3D box dialog is used to select a 3D model to create a 3D box around the model.

Use Fence to:

This option enables you to choose what to do with the fence that you dragged over the part. Select - Select is used to choose the model with the fence. Unselect - Unselect is used to remove a model with the fence that was already chosen.

64

2. CAM-Part

SolidCAM2005 Milling Users Guide

Type

This option enables you to choose the type of elements from the model to use. Solids - Allows solid models to be included in the fence. Surfaces - Allows surfaces to be included in the fence. Both - Allows both solid models and surfaces to be included in the fence.
CAD Selection

Enables you to pick the model with the Host CAD tools.
Expand box at

This eld gives you complete control over how much access stock material you have in each direction of the stock material.
Add box to CAD model

This option enables you to add the stock material to the CAD model.
Finish

Pressing Finish will close this eld. The Geometry Name dialog will be displayed.

Enter a name and press OK. Pressing OK will close this eld and the CAM-Part Data eld will be displayed.

65

SolidCAM2005 Milling Users Guide

2. CAM-Part

Common controls for Target Model and Stock model dialogs

Name

In this eld you can see the target or stock model name and choose the model from the previously dened 3D geometries.
Show

With this button the Stock or Target Model will be shown in the Rest Material window of SolidCAM. If you want to control the quality of the stock & target models visualization, you can change the target tolerance in the SolidCAM Settings (see the topic 10.3.4). In the SolidCAM main menu press the CAM settings In the Units tab you can change the Target tolerance. The recommended tolerance is 0.1mm. A smaller tolerance will improve the quality and reduce the visualization speed.
Show on model

With this button you can see the selected Target model in the Host CAD window.

Target Model

Stock model

66

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.4.3 Updating Stock Model

Update Stock model - After every Job, SolidCAM calculates how much material was actually removed

from the CAM-Part and how much material is left not machined.

Z Buffer With this mode, the rest material is calculated only for one machining direction.

The red area is the rest material left unmachined after the roughing.
Settings

- Pressing the Settings button will open a eld that enables you to control the grid step for the stock model triangulation.

The smaller the grid step, the more precise is the stock model update after each job. However the smaller the grid step, the greater is the calculation time for updating the stock model. It is recommended not to change the default value calculated by SolidCAM, relative to the stock model size. After every job calculation, SolidCAM will update the stock model and save the volume removed by the job tool path.

67

SolidCAM2005 Milling Users Guide

2. CAM-Part

Solid This mode enables you to calculate the Rest material from all sides.

Settings - Pressing the Settings button will open the Solid method settings dialog. This dialog enables you to choose either Automatic or Manual method of the Rest material calculation.

Automatic method

This option causes SolidCAM to automatically calculate and save the rest material after each job. During the SolidVerify simulation (see the topic 8.6) of the separate jobs, SolidCAM updates the stock with the previously generated and saved rest material and performs the simulation on the updated model. Since the rest material models are saved after each job calculation, SolidCAM enables you to simulate any job for multi-sided CAM-Parts.
Manual method

SolidCAM enables you to manually save the Rest Material for a specic job during the SolidVerify simulation (see the topic 8.6). The saved model can be used to update the stock. The simulation of the next jobs can be performed on the updated model.

68

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.5 Tool options

The Tool options enable you to dene additional data about the tools for your CAM-Part. You can enter the start and end position of your tool as well as the coordinates for tool changes on your CNC-machine. After you click on the button, you can change the parameters in the Tool option dialog box. The default values you will receive in this dialog are input from the *.mac le of the selected postprocessor. A sample from the *.mac le is shown below, where the rst three values of each line are metric coordinates and the last three values are in inches. ;Positioning dt_start = 0.0000 200.0000 100.0000, 0.0000 7.8740 3.9370 dt_end = 0.0000 200.0000 0.0000, 0.0000 7.8740 0.0000 set_z_chng = Y dt_tool_chng = 0.0000 0.0000 0.0000, 0.0000 0.0000 0.0000 In the Tool options dialog you can edit the values for the current CAM-Part.

69

SolidCAM2005 Milling Users Guide

2. CAM-Part

Start Point

Determines the position of the rst tool at the start of the milling.
End Point

Determines the position of the last tool at the end of the milling. In most of the cases the value in this dialog will only affect the simulation. In order for this to affect the generated NC program, the postprocessor must use these values. Normally the new CNC controllers do not need the start and end position. In the postprocessor we use the machine command to move to the machine reference point.
Tool Change XY

Denes the XY coordinates of the tool change position. It has 2 possibilities:

Default as in *.mac file

The XY coordinates of the tool change position are dened by the end point of the job that was executed before the tool change.
Define

The XY coordinates of the tool-change position are dened by the user.

Tool Change Z

Denes the Z coordinate of the tool-change position. It has two possibilities:

Default as in *.mac file

The Z-level where tool changes are performed, is automatically read from the Tool start plane specied in the Home data dialog (default input from *.mac le).
Define

The Z-coordinate of the tool change position is dened by the user.

70

2. CAM-Part

SolidCAM2005 Milling Users Guide

Feed Type

Denes the default type of feed used for the tool of this CAM-Part. It has two options: Mm/Min - Millimeters per Minute Mm/Rev - Millimeters per Revolution

2.6 Mac Options

If the *.mac le of your post-processor has extra elds (parameters) dened, they can be accessed through this eld. In the Mac Options dialog you can insert unique information related to the machine controller you have selected. In case of Numeric or Integer eld type, the Numeric / Integer Value dialog box is displayed and you are prompted to enter a value. In case of Logical eld type, the Logical Value dialog box is displayed and you are prompted to choose between Yes and No.

Refer to the GPPTOOL manual for additional information.

71

SolidCAM2005 Milling Users Guide

2. CAM-Part

2.7 Work Material

This option enables you to dene the work material. Choose the Work Material from the list in the list.

The Work material enables you to get Speed/Feed Defaults (see the topic 3.11) based on the work and tool materials that you are using. If you choose the None option the system will offer you an internal standard value spin of 1000 rpm and a default feed for X, Y movement of 100 mm/min.

72

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.8 CNC-Controller and Axis type

Select the CNC Machine Controller. Click the mouse on the arrow next to the controller eld to display the list of post-processors installed on your system. 2.8.1 Axis type This eld displays the CNC-controller type. This eld cannot be changed; it is dened in the postprocessor le. The Axis type can be one of the 3 following types:
3 axis 4_axis_around_X or 4_axis_around_Y 5 axis

The axis type will decide the home denition method:

73

SolidCAM2005 Milling Users Guide

2. CAM-Part

3 axis In this type of machine, every side requires a new clamping (new main home). For each main home you will have to dene the home-origin position, X-axis direction and the Y-axis direction.

4 axis
4_axis_around_X

This type is used for vertical machines with the 4th axis on the table along the X-axis. When dening the main home you have to dene the home-origin position, the X-axis direction and the Y-axis direction. For all additional positioning, based on this clamping, you have to dene the home-origin position and the Y-axis direction only (the angle); the X-axis direction will be determined automatically by the X-axis direction of the main home.

74

2. CAM-Part

SolidCAM2005 Milling Users Guide

4_axis_around_Y

This type is used for horizontal machines with the 4th axis along the Y-axis. When dening the main home you will have to dene the home-origin position, the X-axis direction and the Y-axis direction. For all additional positioning, based on this clamping, you have to dene the home-origin position and the X-axis direction only (the angle); the Y-axis direction will by determined automatically by the Y-axis direction of the main home.

5 axis This type is used for 5-axis CNC machines. For the main home you have to dene the home-origin position, the X-axis direction and the Y-axis direction. All additional positioning is related to this home. The user has to take care of the machine limitations (angles or undercuts). A message on the limit can be generated only during G-Code generation.

75

SolidCAM2005 Milling Users Guide

2. CAM-Part

In the denition process, it is not necessary to consider the kinematics of the CNC machine. This is done in the last step when you generate the NC-program. A CAM-Part created for a CNC-controller of 3-axis type cannot be converted to 4- or 5- axis. A CAM-Part created for the CNC-controller of 4-axis type can be converted to 3-axis type. A CAM-Part created for the CNC-controller of 5-axis type can be converted to 3-axis type.

2.9 Default G-Code numbers

The elds in this area will be displayed according to a parameter dened in the .mac le. ; Program numbers get_prog_num get_proc_num = N or = N or Y Y

If N - the eld will not be displayed.

If Y - the eld will be displayed.

get_prog_num get_proc_num

=Y =N

76

2. CAM-Part

SolidCAM2005 Milling Users Guide

Program Number This eld enables you to dene the number of the main program that will be generated in the output NC program. This eld has ranges that are controlled from the mac le parameters. prog_num_min prog_num_max prog_num_dt =1 = 9999 = 5000

In this case the default number will be 5000. You can change this value and type a number between 1 and 9999. Typing any number beyond this range will be followed with a message:

Subroutine Number In this eld you can dene the number of the rst subroutine in the generated output NC program. This eld has ranges that are controlled from the mac le parameters. proc_num_min proc_num_max proc_num_dt = 1000 = 5000 = 1000

In this case the default number will be 1000. You can change this value and type a number between 1000 and 5000. Typing any number beyond this range will be followed with the same message as above. In some machines (example: Fanuc) the main program number and subroutine number cannot be the same. SolidCAM will not warn you about this problem. In order to prevent this situation, we can set the main program range to 1 - 1000 and the subroutines range to 1001 to 9999 in the Mac le.

77

SolidCAM2005 Milling Users Guide

2. CAM-Part

2.10 Managing CAM-Parts

You can use the commands of the SolidCAM and CAM-Part menus to edit and manage existing CAM-Parts.

Open This command loads a CAM-Part that has been previously saved. When you choose this option, the CAM-Parts browser will be displayed. 1. Select the CAM-Part you want to load.

2. Double click on the CAM-Part or select it and click on the Open button. Close Closes the current CAM-Part.

78

2. CAM-Part

SolidCAM2005 Milling Users Guide

Copy The Copy command creates an identical copy of a CAM-Part in another folder or drive for backup purposes or for making modications without changing the original. The Copy CAM-Parts dialog will be displayed.

1. Choose the drive from which you want to copy the original CAM-Part. 2. Choose the CAM-Parts you want to copy from the CAM-Parts list. 3. Transfer the list of the CAM-Parts you want to copy to the middle eld by pressing the Left to Right arrow. 4. Choose the drive and the directory you want to copy to. 5. Press the Copy button in order to execute the Copy command. Delete This eld enables you to delete a CAM-Part. The Delete CAM-Parts dialog box will be displayed.

79

SolidCAM2005 Milling Users Guide

2. CAM-Part

1. Select the CAM-Part you want to delete. Use the Ctrl-key to select several CAMParts together. 2. Click on the Delete button. 3. Transfer the list of the CAM-Parts you want to delete to the right eld by pressing the Left to Right arrow. 4. A confirmation message will be displayed:

5. Choose Yes to all to delete all selected CAM-Parts. Calculate CAM-Parts Calculates tool paths of all CAM-parts in the specied folder. The Calculate CAM-Parts dialog will be displayed.

1. Click on the Add Directory button. 2. Choose the folder where the CAM-Part is situated via the standard Windowsbrowser. 3. Click on the Calculate button to start the operation. You can also use the Delete All button to remove all the CAM-Parts from the specied folder.

80

2. CAM-Part

SolidCAM2005 Milling Users Guide

Change Model Reference SolidCAM enables you to change the reference to original SolidWorks model. This operation enables you to substitute the DesignModel component of the CAM-Part assembly with some SolidWorks model. 1. Choose the Change Model Reference command in the menu. The Change Model Reference dialog will be displayed.

The OK button is disabled until the data in the dialog is changed.

2. Type the model name in the in the Model Name editbox or choose the model with the Browse button. The Browse button displays the browser dialog that enables you to choose the SolidWorks model.

When the data in the Change Model Reference dialog is changed, the OK button will be enabled.

81

SolidCAM2005 Milling Users Guide

2. CAM-Part

3. Click on the OK button. The following message will be displayed.

When the message is conrmed, the CAM-Part will be closed after which the CAM-Part Reference will be updated, and then the updated CAM-Part will be loaded again.

82

2. CAM-Part

SolidCAM2005 Milling Users Guide

2.11 CAM-Part Documentation

Documentation enables

you to document your tool list, job sequence etc.

Generate

Pressing on Generate will create the document.

Edit

This option enables you to edit the document after it has been generated.
Print

This option enables you to print the document that has been generated.

83

SolidCAM2005 Milling Users Guide

2. CAM-Part

2.11.1 Documentation Editor With the documentation editor you can browse the generated CAM-Part documentation. The tool bar and application menu on the top of the documentation editor works the same as in any typical windows application. The left panel enables you to switch pages and the right page enables you to view and edit each page.
Cover page

Shows contents of Cover page le dened in SolidCAM Settings.

Header page

The Header page contains general information about the CAM-Part. It will give you the CAM-Part name, program number, the amount of jobs and the type of jobs. To edit, simply click the mouse in the right eld and make any changes or additions.

84

2. CAM-Part

SolidCAM2005 Milling Users Guide

Tool Table page

The Tool Table page contains all the relevant information about the tools used in the CAM-Part. It will list the tool number, tool diameter, corner radius, tool type, number of teeth and any other information that is relevant to each tool. To edit, simply click the mouse in the right eld and make any changes or additions.

Jobs table page

The Job table page contains the list of all the jobs in the CAM-Part.

85

SolidCAM2005 Milling Users Guide

2. CAM-Part

Job pages

Under the Job table page, there is a page for each job name. This page gives you a detailed list of all the elds you have chosen in the job and their values.

86

Tools
The tool commands can be used to create and manage tools and tool tables in SolidCAM. You can shorten your programming time if you save the tools you use most often in customizable tool tables. The tool tables can be based on machine tooling, on materials or any other personal criteria. When you define your machining operations, you can then load the tool and all its parameters, feed and spin values are automatically copied to the job.

Working with Part Tool Table Working with Current Tool Table Managing Tool Tables Defining tools Tool types Shaped tools Tool holding system

SolidCAM2005 Milling Users Guide

3. Tools

3.1 User-defined Tool Types

For easier identication and classication of tools, you can dene your own tool types. SolidCAM offers three default tool types, namely: Tool Rough Mill for rough cutters. Tool End Mill for nish cutters. Drill for drills, bores, reams, threading tools etc... Shaped Tool Drill for shaped drills, reams etc... Shaped Tool Rough for shaped rough cutters. Shaped Tool End Mill for shaped nish cutters.
Tool Types

Tool Drill

Tool Rough Mill

Tool End Mill

Shaped Tool Drill

Shaped Tool Rough

Shaped Tool End

User-dened tool types can also be used to dene new tools and to search tool tables.

88

3. Tools

SolidCAM2005 Milling Users Guide

3.1.1 Add new Tool Types Based on one of the three default tool types, you can create user-dened tool types. 1. Choose the SolidCAM item from the SolidWorks main menu. Choose the Tool type names item from the Tool Table sub-menu.

The Tool types names dialog will be displayed. This dialog shows the user-dened tool type names and their actual SolidCAM default internal tool types. 2. In the Tool types names dialog, move the cursor on an existing tool type name, e.g. TOOL END MILL and press the right mouse button.

3. Select Add from the menu. 4. A new entry will be created. Enter the name of the user-dened tool-type.

89

SolidCAM2005 Milling Users Guide

3. Tools

5. By default, the new entry will be of tool type DRILL. With the right mouse button, click on the DRILL eld and select the relevant tool type from the list.

6. After you have completed your changes in the tool type list, click on the Save button to conrm your changes. Click the tool type name twice to re-name existing entries.

3.1.2 Delete Tool Types You can delete user-dened tool types from the list. 1. In the Names List dialog, move the cursor on an existing tool type name, e.g. TOOL END MILL and press the right mouse button. 2. Choose the Delete item from the menu and conrm the displayed conrmation message with OK.

90

3. Tools

SolidCAM2005 Milling Users Guide

3.2 Tool Tables

The tool tables can be based on machine tooling, on materials or any other personal criteria. When you dene your machining operations, you can then load the tool and all its parameters, feed and spin values are automatically copied to the job. The Part Tool Table is the tool table that contains all the tools that are available for use within a specic CAM-Part. The Part Tool Table is stored within the CAM-Part. When you start a new CAM-Part and you want to automatically copy the contents of a specic tool table into the Part Tool Table of this CAM-Part, specify its name in the MAC-le of the CNC machine; this le is called Machine Tool Table. The Machine Tool table is dened in the MAC-le by the following parameter: tool_table_name = name; where name (without extension) is the name of the Tool Table located in the SolidCAM Tool tables folder dened in the SolidCAM settings (see the topic 10.2.2). Generally, the Machine Tool Table contains the tools situated in the Tool Magazine of the specied CNC Machine. SolidCAM enables you to dene any number of Tool Tables. Each tool from such Tool Tables can be imported into the Part Tool Table. SolidCAM enables you to dene one Tool Table that has a top priority in the list for import; this is the Current Tool Table.
Job Tool Job Tool Job Tool CAM-Part

Part Tool Table

Tools imported at start
Machine Tool Table Tool Table

Tools imported at user choise

Current Tool Table Tool Table

Tool Table

Tool Table

91

SolidCAM2005 Milling Users Guide

3. Tools

3.3 Working with Part Tool Table

The Part Tool Table is the tool table that contains all the tools that are available for use within a specic CAM-Part. The Part Tool Table is stored within the CAM-Part. SolidCAM enables you to display the Part Tool Table dialog (see the topic 3.6). This dialog enables you to manage the tools contained in the Part Tool Table. 1. Choose the Part Tool table option from the right-click menu on the Tool header in the CAM Manager.

2. The Part Tool Table dialog will be displayed.

92

3. Tools

SolidCAM2005 Milling Users Guide

3.4 Working with Current Tool Table

SolidCAM enables you to control your Current Tool Tables with the right-click menu available on the Tool header in the SolidCAM Manager.

Set as Current Tool Table

This option enables you to set the Current Tool Table. You have to specify the type of the Current Tool Table (Milling, Turning or Milling&Turning) and choose the necessary Tool Table with the browser-styled dialog. The Current Tool table will be selected and displayed in the Tool Table dialog (see the topic 3.6).

Close Current Tool Table

This option enables you to close the Current Tool Table. This option is active only when the Current Tool table is already dened.

93

SolidCAM2005 Milling Users Guide

3. Tools

Show Current Tool Table

This option enables you to display the content of the Current Tool tables. The Tool Table dialog enables you to manage the tools in the Current Tool Table and edit them. This option is active only when the Current Tool table is already dened.

Recent Tool Tables

This option displays a list of the recently loaded Current Tool Tables. You can open the le by simply clicking on its name. The Tool Table dialog will be displayed.

94

3. Tools

SolidCAM2005 Milling Users Guide

3.5 Managing tool tables

SolidCAM enables you to manage your Tool Tables with the Tool Table menu available from the SolidCAM main menu.

3.5.1 Edit Tool table This option enables you to display the content of the specic Tool Table. When you choose this option, the Load dialog will be displayed.

1. Select the tool table you want to load. 2. Double click on the tool table or select it and click on the Open button. The Tool Table dialog will be displayed. This dialog enables you to manage the tools in the chosen Tool Table and edit them.

95

SolidCAM2005 Milling Users Guide

3. Tools

3.5.2 Create Tool table This option enables you to dene a new Tool Table. 1. Choose the Tool Table type (Milling, Turning or Milling&Turning) from the submenu.

2. Dene the Tool table name

3. Conrm the Tool table creation with the OK button. The Tool Table will be created. The Tool Table dialog will be displayed enabling you to add tools to the new Tool Table.

96

3. Tools

SolidCAM2005 Milling Users Guide

3.5.3 Copy tool table Creates an identical copy of a tool table in another folder or drive for backup purposes or for making modications without changing the original. The Copy tool table dialog box will be displayed.

1. In the left window, choose the drive and directory from which you want to copy the original tool table. 2. Select the tool table you want to copy. 3. Transfer the selection of tool tables you want to copy to the middle window by pressing the Left to Right arrow. 4. Choose the drive and the directory you want to copy in on the right window. 5. Press the Copy button to execute the copy command.

97

SolidCAM2005 Milling Users Guide

3. Tools

3.5.4 Delete tool table This eld enables you to delete tool tables. The Delete Tool tables dialog box will be displayed.

1. Select the tool tables you want to delete. Use the Ctrl-key to select several tool tables together. 2. Click on the Delete button. 3. A conrmation message will be displayed:

4. Choose Yes or Yes to all to delete all selected tool tables.

98

3. Tools

SolidCAM2005 Milling Users Guide

3.6 Tool Table dialog

The Tool table dialog contains structured information about all tools included in the specied Tool Table. This dialog enables you to add new tools to the Tool Table, remove tools from the tool Table, edit the tool denition etc.

The dialog contains two pages:

Tool table - View

This page displays the tools of the Tool Table in table format.
Tool table - Edit

This page enables the addition of new tools or editing of existing tools in the Tool Table.

99

SolidCAM2005 Milling Users Guide

3. Tools

3.6.1 Tools Filter SolidCAM enables you to lter tools that will be displayed in the Tool Table dialog.

All

All the tools will be displayed.

Used

Only the tools used by Jobs of the current CAM-Part will be displayed.
Unused

Only the tools unused by Jobs of the current CAM-Part will be displayed. The lter is available only for the Part Tool table.

100

3. Tools

SolidCAM2005 Milling Users Guide

3.6.2 Tool Range If you work with large tool tables, you can use this option to reduce the number of tools displayed. You can also search the tool table for tools that match your criteria. In the Tool Range dialog, enter the required properties of the tool. Enter only values that are different; leave the other elds unchanged.

Sort by enables

you to list the search results according to:

Tool number.

Lists results according to the tool numbers.

Sequence number. Lists results according to the sequence in which the tools were dened.
User-defined tool type

table.

allows you to choose the type of tool you would like to have listed in the tool

ID Number allows you to choose the range of

the ID Number of the tools you would like to have listed in the tool table. If, for example, you would like to list the tools that have an ID Number from 10 to 100, enter in the From eld 10 and in the To eld 100.
Diameter allows you to choose the range using the diameter of

the tools you would like to have listed in the tool table. If, for example, you would like to list the tools that have a diameter from 1 to 16, enter in the From eld 1 and in the To eld 16. allows you to choose the range using the number of teeth of the tools you would like to have listed in the tool table. If, for example, you would like to list the tools that have from 1 to 4, enter in the From eld 1 and in the To eld 4.
Teeth number

101

SolidCAM2005 Milling Users Guide

3. Tools

allows you to choose the range of the tool number of the tools you would like to have listed in the tool table. If, for example, you would like to list the tools that have the tool number from 1 to 30, enter in the From eld 1 and in the To eld 30.
Tool number Sequence number

allows you to choose the range of the tool sequence number of the tools you would like to have listed in the tool table. If, for example, you would like to list the tools that have the tool sequence number from 1 to 30, enter in the From eld 1 and in the To eld 30.

allows you to choose the range using the corner radius of the tools you would like to have listed in the tool table. If, for example, you would like to list the tools that have a corner radius from 0 to 4, enter in the From eld 0 and in the To eld 4.
Corner radius Angle allows you to choose the range using the angle of the tools you would like to have listed in the tool table. If, for example, you would like to list the tools that have an angle from 90 to 180, enter in the From eld 90 and in the To eld 180. Execute. Click on the Execute button and the tool table will be searched for the tools that match your requirements. SolidCAM will return to the tool table and display the result of the range search. The Reset to defaults button

returns you to the original program settings of this dialog.

3.6.3 Show Tool This option enables you to display the selected tool.

102

3. Tools

SolidCAM2005 Milling Users Guide

3.6.4 Tool table - View This page displays the tools data in table format. The table contains the following columns:

Tool Number

Displays the tool number in the Part Tool Table.

ID Number

Displays the ID number of the tool

Tool type name

Shows the tool type.

Description

Displays a description of the tool. This page also displays the geometry parameters of the tool depending on the tool type.

103

SolidCAM2005 Milling Users Guide

3. Tools

3.6.4 Tool table - Edit

This page enables the addition of new tools or editing of the existing tools in the Tool Table.

104

3. Tools

SolidCAM2005 Milling Users Guide

3.7 Managing tools

SolidCAM enables you to manage the tools in the tool table with the buttons at the bottom of the dialog. All the operations are also available with the right-click menu.

The following options are available:

Permanent Tool

If a particular tool that is being used is always in the same magazine position in the machine, the tool can be marked as a Permanent Tool. If you use the Tool Renumbering function, a tool that is marked as a Permanent Tool will not be renumbered.
Add Tool

This option enables you to add a new tool.

105

SolidCAM2005 Milling Users Guide

3. Tools

Copy Tool

This option enables you to create a copy of an existing tool.

Delete Tool

This option enables you to delete the selected tool.

Tools Renumbering

This option enables you to renumber the tools.

In the case above, the numbers are not in order. With Tool Renumbering we can renumber the tools in numeric order. The tools can also be renumbered from a specic number that you choose. 1. Activate this option by choosing the command: Tool Renumbering.

2. You are prompted to enter the new number for the rst tool.

106

3. Tools

SolidCAM2005 Milling Users Guide

All the tools are then renumbered accordingly, starting from the number of this rst tool.

3. Re-calculate the CAM-Part. The CAM-Part must be recalculated so that the GCode will have the correct tool number for each job. A tool that has been marked as a permanent tool will not be renumbered.
Import Tool

This option enables you to import tools to the Tool Table from the Current Tool Table or any other Tool table. The Tool tables list will be displayed. The Current Tool Table, which is the rst in the list, will be automatically chosen.

107

SolidCAM2005 Milling Users Guide

3. Tools

SolidCAM enables you to choose the location of the Tool Tables for the tools import.

The Table Name combo-box enables you to choose the Tool table for the tools import. The Parts checkbox enables you to import tools from the CAM-Parts situated in the specied location. If the Current Tool Table is dened, it will be automatically chosen as origin for tools imports. The tools list displays all the tools contained in the specied tool table. The right-click menu is available. The Copy to Table command imports the selected tools to the Tool Table.

Update to Machine Tool table

This option enables you to update the Machine tool Table with the tools of an active Tool Table. This option is available when the Tool Table dialog is loaded outside the Job. This option is active only when the Machine Tool Table is dened in the MAC le. The Update to Machine tool table dialog will be displayed.

This dialog displays the name of the Machine Tool Table. The Used Tools only option enables you to update the Machine Tool Table only with the tools used in Jobs.

108

3. Tools

SolidCAM2005 Milling Users Guide

Export all tools to Excel

This option enables you to export all the tool data to an Excel le.

Import all tools from Excel

This option enables you to import the tool data from an Excel le.

109

SolidCAM2005 Milling Users Guide

3. Tools

3.8 Tool data

SolidCAM enables you to dene the Tool with the following data: Geometry parameters Tool Material Feed and Spin defaults Tool Holder

Tool denition

Tool material

Speed and Feed

Tool Holder

Geometry denition

R D

The Tool Data area displays the parameters of the selected tool.

L
110

3. Tools

SolidCAM2005 Milling Users Guide

3.8.1 Tool Type This eld shows the tool type. The tool types were dened with the Tool type names dialog. These types are the internal tool types. SolidCAM checks the possibility of a specic internal tool type to work in the selected job. Selecting a shaped tool will activate the Tool name section on the Tool topology page. The Topology page contains the Topology Data of the tool like diameter, length, angle, corner radius etc. The Default Tool Data page contains the default Tool Material data, Feed and Spin data and diameter and length offset numbers.

111

SolidCAM2005 Milling Users Guide

3. Tools

3.8.2 Topology page

ID Number

You can use any number, e.g. the catalog number of the tool to facilitate its identication.
Tool Number

Denes the number of the tool in the CAM-Part. SolidCAM will assign a sequential tool number for each new job. You can use previously selected tools by simply entering the tool number. The tool number is used in the G-Code when tool changes, tool length and radius values for tool compensation (G4x) are read from the machine controller. Make sure that the tool number is identical to the actual tool position in the machine before you machine the workpiece.
Diameter

Denes the cutting diameter of the tool.

Corner Radius/Angle

When the tool type is Rough-Mill or End-Mill, the Corner Radius eld is displayed. If the tool type is Drill, the Angle eld is displayed.

112

3. Tools

SolidCAM2005 Milling Users Guide

Corner Radius

Enter the corner radius of the tool. There are three possibilities:

In ball nosed mills, the corner In radius end mills, the corner A flat mill has a corner radius radius is equal to the radius of the radius is less than the radius of of zero. tool. the tool.
Angle

Enter the drill point angle of the tool (between 0.01 and 180 deg).

113

SolidCAM2005 Milling Users Guide

3. Tools

Length

This eld denes the length of the tool. In milling calculations, the system does not use this data; the length of the tool is only output to the G-Code le.
Total

The total tool length.

Outside Holder

The length of the tool outside the tool holder.

Cutting

The length of the cutting part of the tool.

Total Length

Cutting Length Outside Holder Length

Number of Teeth

Denes the number of teeth of the tool. This eld is used when calculating the feed in the Feed rate type FZ.
Description

This eld enables you to enter a description of the tool (up to 40 characters).

114

3. Tools

SolidCAM2005 Milling Users Guide

Tool parameters

This eld contains two pictures: Schematic picture of the current tool with its dimensions. 3D model of the tool with the specied tool holder. In the graphic area of this page you can rotate, zoom and pan the 3D model of the tool Holder Use the following combinations: Middle mouse button - Rotation of tool holder Shift + Middle mouse button - Zoom of tool holder Ctrl + Middle mouse button - Pan of tool holder
Tool Name

This eld enables you to choose the shaped tool from the local/global tool table. This eld is activated only if the shaped tools type (Shaped Tool Drill, Shaped Tool Rough, Shaped Tool End Mill) is chosen.

Global shape-tools table

The Shape-tool dialog will be displayed enabling you to choose the shaped tool from the Global shape-tools table. The selected tool will be copied in the Local shape-tools table that is relative to the current CAM-Part.
Local shape-tools table

This option enables you to choose the previously used in the current CAM-part shape-tool from the Local shape-tools table. The Shape-tools dialog will be displayed.

115

SolidCAM2005 Milling Users Guide

3. Tools

Shape Edit

This option enables you to change dimensions of the selected shape-tool. The Shapetools Edit dialog will be displayed. For more information on this using shaped tools, please refer to topic 3.10.
Holder

This eld enables you to choose the tool holder parts from the tool holders table.

The tool adaptor is dened in the MAC-le according to your CNC-machine. If the tool adaptor is not described in the MAC-le, the rst tool adaptor from the table will be used.
Global holders table

The Tool Holders dialog will be displayed in order to choose the tool holder components from the Global holders table. The selected tool will be copied in the Local holders table that is relative to the current CAM-Part.
Local holders table

This option enables you to choose the tool holder component previously used in the current CAM-part from the Local holders table. The Tool Holders dialog will be displayed
Shape Edit

This option enables you to change dimensions of the selected clamping adaptor. The Tool Holders Edit dialog will be displayed. For more information on this using tool holders, please refer to topic 3.10.

116

3. Tools

SolidCAM2005 Milling Users Guide

3.8.3 Default tool data / Job Data

Tool Material

The Tool Material is used to describe one or more of the following properties of the tool: Material of the tool (High Speed Steel, Carbide etc) Working conditions of the tool Use of tool (rough, nish, etc) The Tool Material is used to dene the Speed and Feed defaults. When you choose the Tool material, the feed type will be changed to Fz and the spin type to V. The Feed and Spin values are default system values since the Work material has not been dened yet. Loading the tool to a job will connect the Tool material to the Work material and the correct Feed and Spin values will be loaded from the Speed/Feed defaults table.

117

SolidCAM2005 Milling Users Guide

3. Tools

Spin

This eld denes the spinning speed of the tool. It denes two spin values: Spin Rate - Normal spin-rate; used in rough milling. Spin Finish - Finish spin-rate; used in nish milling. The spin value can be dened in two types of units, namely S and V. is the default and it signies Revolutions per Minute. V signies Material cutting speed in Meters/Minute in the Metric system or in Feet/Minute in the Inch system; it is calculated according to the following formula:
S V = (S * PI * Tool Diameter) / 1000

Feed

This eld denes the feed rate of the tool. It denes three feed values: Feed XY - Feed-rate in the XY plane. Feed Z - Feed-rate in the Z direction. Feed Finish - Feed-rate used for nish milling. The feed value can be dened in two types of units, namely: F and Fz.
F is the default and it signies Units per minute. Fz signies Units per tooth and is calculated

according to the following formula:

Fz = F/(Number of Teeth * S)

Diameter Offset Number

This parameter denes the number of the Diameter Offset Register of the current tool in the Offset table of the CNC machine.
Length Offset number

This parameter denes the number of the Length Offset Register of the current tool in the Offset table of the CNC machine.

118

3. Tools

SolidCAM2005 Milling Users Guide

3.9 Tool holding system

SolidCAM enables you to dene a variety of tool holders to help you check and prevent all possible collisions of the tool holding system with the workpiece. This feature also enables you to see a more realistic simulation when using the Solid Verify simulation. The SolidCAM tool holder is dened by combining two components. The rst component is the tool adaptor mounted in the spindle unit of the milling machine. The second component can consist of different types of extensions and reductions like collet chucks, arbors, shanks and any other components that you may have.
Tool adaptor

}
Tool

Tool Holding system

Extensions and reductions

119

SolidCAM2005 Milling Users Guide

3. Tools

3.9.1 Tool holders dialog This dialog enables you to dene and operate your tool holders. 1. Click on the SolidCAM item in the SolidWorks main menu. 2. Choose the Tool Holders... item from the Tool Table sub-menu.

3. The Tool Holders dialog will be displayed. A CAD model le will also be displayed to enable you to dene the geometry of the new holders.

120

3. Tools

SolidCAM2005 Milling Users Guide

Tool holder component tables The rst list displayed above enables you to dene and manage your tool adaptors.

1. Right click on the item name in the table. The submenu will be displayed.

2. Choose the command from the submenu.

Add Holder Component

This option enables you to dene the geometry of the new tool adaptor that will be added to the table. The Holder Geometry dialog will be displayed.
Generate

This option generates the sketch in the model le with the geometry of the selected tool adaptor.
Replace

This option enables you to replace the existing tool adaptor geometry with a new one. The Holder Geometry dialog will be displayed to select the new geometry.

121

SolidCAM2005 Milling Users Guide

3. Tools

Delete

This option enables you to remove the tool adaptor part from the list.
Rename

This option enables you to assign a new name to the tool adaptor.
Copy

This option enables you to create a copy of the existing tool adaptor. The second list enables you to dene and manage groups of reductions and extensions such as collet chucks, arbors, shanks etc.

1. Right click on the group/component name in the table. The submenu will be displayed.

2. Choose the command from the submenu.

122

3. Tools

SolidCAM2005 Milling Users Guide

Add Group

This option enables you to create a group of components and to dene separate groups for tool holders components of the same type.
Add Holder Component

This option enables you to dene the geometry of the new component that will be added to the current group of the parts table. The Holder Geometry dialog will be displayed.
Generate

This option generates the sketch in the model le with the geometry of the selected tool holder.
Replace

This option enables you to replace the existing holder geometry with a new one. The Holder Geometry dialog will be displayed to select the new geometry.
Delete

This option enables you to remove the tool holder component from the list.
Rename

This option enables you to assign a new name to the tool holder component or group.
Copy

This option enables you to create a copy of the existing tool holder component. Description SolidCAM enables you to type a brief description of the tool holder component (reduction or extension). Show tab This page enables you to see a 3D model of the tool holder. In the graphic area of this page you can rotate, zoom and pan the 3D model of the tool holder. Use the following combinations: Middle mouse button - Rotation of tool holder Shift + Middle mouse button - Zoom of tool holder Ctrl + Middle mouse button - Pan of tool holder
123

SolidCAM2005 Milling Users Guide

3. Tools

Edit tab This page enables you to edit the parameters of the selected tool holder component. 1. Select the tool holder component. 2. Switch to the Edit page to change the dimensions of the tool holder component. The interactive picture of the selected tool holder component will be displayed. The parameters pages are located below the picture.

SolidCAM divides the tool holder component into solid segments like cylinders, cones or toruses. For each solid primitive, SolidCAM determines actual dimensions. For more information on this subject, please refer to topic 3.9.3. You can change the dimensions of each segment with its specic page. 1. Select the segment on the picture or through the tabs below the picture. 2. Type the new value of the parameter in the value eld.

124

3. Tools

SolidCAM2005 Milling Users Guide

3.9.2 Tool Holder Geometry definition This dialog enables you to dene the geometry of the tool holder component.

Define chain This option enables you to dene a new chain of the component geometry. The Chain selection dialog will be displayed. In the model le displayed, you can sketch the shape of half the tool holder component and then dene the chain. The direction of the chain does not matter. Note that the left side of the sketch is the bottom of the tool holder component and the right side is the top.

Replace chain This command enables you to replace a chain in the current chain geometry. Edit chain This command enables you to update a chain in the current chain geometry. Reference point This option enables you to dene the reference point through which the rotation axis of the tool holder component passes.
125

SolidCAM2005 Milling Users Guide

3. Tools

3.9.3 Tool Holder segments SolidCAM determines three types of segments of the Holder Geometry. Cylinder Diameter Height
Diameter

Height

Cone Top Diameter Bottom Diameter Height Angle

Angle

Top Diameter

Height

Bottom Diameter
The following rules apply when parameters are changed: Changing of the Angle causes Top Diameter change Changing of the Bottom Diameter causes Height change Changing of the Top Diameter causes Bottom Diameter change Changing of the Height causes Bottom Diameter change

126

3. Tools

SolidCAM2005 Milling Users Guide

Torus
Top Diameter Radius Start Angle Sweep Bottom Diameter
Top Diameter Start Angle Sweep

Bottom Diameter

Radius

The following rules apply when parameters are changed: Changing of the Radius causes Bottom Diameter change Changing of the Top Diameter causes Bottom Diameter change Changing of the Bottom Diameter causes Top Diameter change Changing of the Start Angle causes Bottom Diameter change Changing of the Sweep Angle causes Top Diameter change

127

SolidCAM2005 Milling Users Guide

3. Tools

3.9.4 Using Tool Holders

Global holders table

The Tool Holders dialog will be displayed in order to choose the tool holder components from the Global holders table. The selected tool will be copied in the Local holders table that is relative to the current CAM-Part.
Local holders table

This option enables you to choose the tool holder component previously used in the current CAM-part from the Local holders table. The Tool Holders dialog will be displayed
Shape Edit

This option enables you to change dimensions of the selected clamping adaptor. The Holders Edit dialog will be displayed.

128

3. Tools

SolidCAM2005 Milling Users Guide

SolidCAM enables you to choose the tool holder component through the Tool Holders dialog. Note that the tool-adaptor section is inactive and you cannot select the adaptor type. SolidCAM enables you to dene the Tool adaptor in the Mac le with the following string:
mac_holder = BT45

If the parameter is not dened in the MAC le, SolidCAM will use the rst adaptor from the list; the extenders are the same for all the adaptors. If all your machines use the same type of adaptor, you do not need to dene the mac_holder parameter. In the table, drag and drop the requested adaptor to the rst place on the list.

In the Show area, SolidCAM displays a 3D model of the selected tool holder. In the graphic area of this page you can rotate, zoom and pan the 3D model of the tool holder. Use the following combinations: Middle mouse button - Rotation of tool holder Shift + Middle mouse button - Zoom of tool holder Ctrl + Middle mouse button - Pan of tool holder

129

SolidCAM2005 Milling Users Guide

3. Tools

Holders Edit dialog The Holders Edit dialog enables you to edit the dimensions of the selected tool holder component. This dialog contains two tabs:
Show

This page displays a 3D-model of the selected tool holder component.

In the graphic area of this page you can rotate, zoom and pan the 3D model of the tool holder. Use the following combinations: Middle mouse button - Rotation of tool holder Shift + Middle mouse button - Zoom of tool holder Ctrl + Middle mouse button - Pan of tool holder.

130

3. Tools

SolidCAM2005 Milling Users Guide

Edit

The interactive picture of the selected tool holder component will be displayed. The tool holder component is divided into segments such as cylinders, cones and toruses. The Parameters table below the picture enables you to edit the actual dimensions of the tool holder component. 1. Select the holders element on the picture or through the parameter pages. 2. Type the new value of the parameter in the value eld.

131

SolidCAM2005 Milling Users Guide

3. Tools

3.10 Shaped Tools

In addition to three built-in tool types, SolidCAM enables you to use shaped tools. The geometry of these tools is dened with a sketch. This way you can create your own database of tapered mills, Tshaped mills etc.

132

3. Tools

SolidCAM2005 Milling Users Guide

3.10.1 Shape-Tools dialog This dialog enables you to dene and operate your shaped tools.

Choose the SolidCAM item from the SolidWorks main menu. Choose the Shaped tools item from the sub-menu.

The Shape-Tools dialog will be displayed. A CAD model le will also be displayed to enable you to dene the geometry of new shape-tools.

133

SolidCAM2005 Milling Users Guide

3. Tools

Tools list This eld displays the database of shaped tools dened in SolidCAM. With this list you can dene and manage shaped tools. 1. Right-click on the any item in the browser eld of the Shape-Tools dialog. The following menu will be displayed.

2. Choose the specic command from the menu.

Add Group

This option enables you to create a group of the shaped tools. This option enables you to dene separate groups for shaped tools of the same type.
Add Tool

This option enables you to dene the geometry of the newly shaped tool that will be added to the current group of the shape-tools table. The Shape-Tool Geometry dialog will be displayed.
Generate

This option generates a sketch in the model le with the geometry of the selected shapetool.
Replace

This option enables you to replace the existing shape-tool geometry with a new one. The Shape-Tool Geometry dialog will be displayed to select the new geometry.
Delete

This option enables you to remove the shape-tool from the database.

134

3. Tools

SolidCAM2005 Milling Users Guide

Rename

This option enables you to assign a new name to the selected shape-tool or group.
Copy

This option enables you to create a copy of the selected shape-tool. Description You can place a brief description of the shaped tool here. Show tab This page enables you to see a 3D model of the selected shaped tool. In the graphic area of this page you can rotate, zoom and pan the 3D model of the shaped tool. Use the following combinations: Middle mouse button - Rotation of tool Shift + Middle mouse button - Zoom of tool Ctrl + Middle mouse button - Pan of tool

135

SolidCAM2005 Milling Users Guide

3. Tools

Edit tab This page enables you to edit the parameters of the selected shaped tool. 1. Select the Shape-tool. 2. Switch to the Edit page to change the shape-tool dimensions. The interactive picture of the selected shaped tool will be displayed. The parameters pages are located below the picture.

SolidCAM divides the tool into solid segments like cylinders, cones or toruses. For each solid primitive, SolidCAM determines actual dimensions. You can change the dimensions of each segment with its specic page. 1. Select the tools element on the picture or through the parameter pages. 2. Type the new value of the parameter in the value eld.

136

3. Tools

SolidCAM2005 Milling Users Guide

3.10.2 Shape-tool geometry definition This dialog enables you to dene the geometry of the shaped tool.

Define chain This option enables you to dene a new chain of the shaped tool geometry. The Chain selection dialog will be displayed. In the model le displayed, you can sketch half of the shaped tool and then dene the chain. The direction of the chain does not matter. Note that the left side of the sketch is the bottom of the tool and the right side is the top.

Replace chain This command enables you to replace a chain in the current chain geometry. Edit chain This command enables you to update a chain in the current chain geometry. Reference point This option enables you to dene the reference point through which the rotation axis of the shapetool passes.
137

SolidCAM2005 Milling Users Guide

3. Tools

3.10.3 Shaped Tool segments SolidCAM determines three types of segments of the Shaped Tool Geometry. Cylinder Diameter Height
Diameter

Height

Cone Top Diameter Bottom Diameter Height Angle

Angle

Top Diameter

Height

Bottom Diameter
The following rules apply when parameters are changed: Changing of the Angle causes Top Diameter change Changing of the Bottom Diameter causes Height change Changing of the Top Diameter causes Bottom Diameter change Changing of the Height causes Bottom Diameter change

138

3. Tools

SolidCAM2005 Milling Users Guide

Torus
Top Diameter Radius Start Angle Sweep Bottom Diameter
Top Diameter Start Angle Sweep

Bottom Diameter

Radius

The following rules apply when parameters are changed: Changing of the Radius causes Bottom Diameter change Changing of the Top Diameter causes Bottom Diameter change Changing of the Bottom Diameter causes Top Diameter change Changing of the Start Angle causes Bottom Diameter change Changing of the Sweep Angle causes Top Diameter change

139

SolidCAM2005 Milling Users Guide

3. Tools

3.10.4 Using Shaped tools The Tool eld enables you to choose the shaped tool from the local/global tool table.

This eld is activated only if the shaped tools type (Shaped Tool Drill, Shaped Tool Rough, Shaped Tool End Mill) is chosen.
Global shape-tools table

The Shape-tool dialog will be displayed enabling you to choose the shaped tool from the Global shape-tools table. The selected tool will be copied in the Local shape-tools table that is relative to the current CAM-Part.
Local shape-tools table

This option enables you to choose the previously used in the current CAM-part shape-tool from the Local shape-tools table. The Shape-tools dialog will be displayed.
Shape Edit

This option enables you to change dimensions of the selected shape-tool. The Shapetools Edit dialog will be displayed.

140

3. Tools

SolidCAM2005 Milling Users Guide

Shape-tool dialog SolidCAM enables you to choose the specic shaped tool with the Shape-tools browser.

In the Show area, SolidCAM displays a 3D model of the selected tool. In the graphic area of this page you can rotate, zoom and pan the 3D model of the tool. Use the following combinations: Middle mouse button - Rotation of tool Shift + Middle mouse button - Zoom of tool Ctrl + Middle mouse button - Pan of tool

141

SolidCAM2005 Milling Users Guide

3. Tools

Shape edit The Shape-tools Edit dialog enables you to edit the dimensions of the selected tool. This dialog contains two pages:
Show

This page displays a 3D-model of the selected tool.

In the graphic area of this page you can rotate, zoom and pan the 3D model of the tool. Use the following combinations: Middle mouse button - Rotation of tool Shift + Middle mouse button - Zoom of tool Ctrl + Middle mouse button - Pan of tool

142

3. Tools

SolidCAM2005 Milling Users Guide

Edit

The interactive picture of the selected shaped tool will be displayed. The tool is divided into segments like cylinders, cones and toruses. With the Parameters table below the picture, you can edit the actual dimensions of the shaped tool. 1. Select the tools element on the picture or through the parameter pages. 2. Type the new value of the parameter in the value eld.

143

SolidCAM2005 Milling Users Guide

3. Tools

3.11 Feed and Speed default

The Speed/Feed Default option enables the program to calculate the speed and feed rate according to the Work material and Tool material you are using.
Tool Material Work Material

Speed/Feed Defaults

Choose the Speed&Feed Defaults item from the Tool Table sub-menu.

The Default settings dialog will be displayed.

144

3. Tools

SolidCAM2005 Milling Users Guide

This dialog enables you to dene the Work Material and the Tool Material and to dene the different values of the Speed and Feed for each combination set. The dialog shows the tree-control list of the existing Tool and Work Materials. The root items of the tree are the Tool Materials; for each tool material you can see the list of the Work Materials for which Speed/Feed default is dened. The right area of the dialog shows the Speed/Feed parameters for each selected pair of Tool material and Work material.

145

SolidCAM2005 Milling Users Guide

3. Tools

Add/Delete tab This tab enables you to operate the Tool and Work materials and dene the Speed and feed values for the combination of the tool and work materials.

Right click in the tool/work material list and choose the specic item from the menu.
Add Tool Material

This option enables you to add the new Tool Material. The combination pairs of the new Tool material with the existing Work materials will be automatically added. Type the name for the new Tool Material.
Add Work Material

This option adds a new Work material. The Work material will be added to all existing Tool material combinations.
Delete

This option removes the selected Tool/Work material from the list.
Rename

This option enables you to assign a new name to the selected Tool/Work material.
Work material parameters

Within this area you have to assign the Speed and Feed values for the selected Tool/Work material combination. SolidCAM enables you to dene the following values:

146

3. Tools

SolidCAM2005 Milling Users Guide

V V fin Fz XY Fz Z Fz fin

Signies the Rough Material cutting speed in Meters/Minute in the Metric system or in Feet/Minute in the Inch system. Signies the Finish Material cutting speed in Meters/Minute in the Metric system or in Feet/Minute in the Inch system. Feed-rate in the XY plane, in Units per tooth. Feed-rate in the Z direction, in Units per tooth. Feed-rate used for nish milling, in Units per tooth.

Edit tab This tab enables you to edit the values of the Speed and Feed for each combination of the Tool/Work material.

Click on the parameter you have to change and enter the new value.

147

SolidCAM2005 Milling Users Guide

3. Tools

148

Geometry
Whenever you work in CAD, you use 2D wireframe curves and 3D models to describe real life parts. With SolidCAM, you can turn these models into G-Code for any CNC-machine. A major step in the process from modeling to manufacturing is to tell SolidCAM what and where you want to machine. In SolidCAM you use your existing models to pass this information to the CAM module.

Defining a new Geometry Drill Geometry 3D Model Geometry Wireframe Geometries Managing Geometries Geometry synchronization

SolidCAM2005 Milling Users Guide

4. Geometry

4.1 Introduction
SolidCAM enables you to turn 3D models, 2D and 3D sketches built with SolidWorks into G-code for any CNC-machine. In this process of modelling to manufacturing, geometries have to be dened to determine where the model will be machined. In SolidCAM, you can dene geometries in two places; in the Geometries eld of the CAM-Manager and in each job. Dening geometries in the Geometries eld is only possible if the CAM-part uses homes dened with Projections mode; otherwise, this eld is inactive. It is recommended to dene the geometry from the Job dialog; this enables SolidCAM to check if the geometry follows the necessary rules needed in this type of job. The Geometries dened in SolidCAM are associative to the SolidWorks model. Any change made to the model or sketch will propogate to referenced SolidCAM Geometry. There are types of geometries used in SolidCAM:

Geometry

3D

Wireframe

Drill

3D Model

Profile
Pocket
Working Area
Slot
Limit
Section

Faces

150

4. Geometry

SolidCAM2005 Milling Users Guide

4.2 Adding a new Geometry to your CAM-Part

You can add a new geometry from the Geometry eld of the CAM-Manager. Whenever there is a geometry required in a Job, you can select it directly with the Dene button. 1. In the CAM Manager, move the mouse on the Geometry eld and press the right mouse button. The Geometry menu will be displayed.

2. Move to the Add sub-menu and select the type of geometry you want to dene. In the Multi-sided mode, the Geometry can be dened only from a Job screen. The reason of this limitation is the dependency of the geometry on the Home that is used for this operation.

151

SolidCAM2005 Milling Users Guide

4. Geometry

4.3 Drill Geometry

A Drill Geometry consists of one or more points (drilling centers) that are dened by X,Y and Z values. They can be selected from models using a number of different methods.

4.3.1 Defining a Drill Geometry In Drilling operations, you have to dene the coordinate points where SolidCAM should execute the drill cycles. The powerful selector tool enables you to dene and edit drill positions quickly and easily. In the Example above the drill points have been selected by their radius and Z-level on a 3D solid model. With automatic selection the distance between two drilling points is optimized to reduce machining time. 1. After you have selected the command to add or dene a Drill geometry, the Drill Geometry Selection dialog is displayed. 2. Select your parameters and options in the Drill Geometry Selection dialog. 3. When you have picked all your drill positions, conrm the Drill Geometry dialog with Finish. 4. Conrm the Default Geometry Name (see the topic 10.12.) or enter a new name for the geometry into the Geometry name dialog and conrm with OK.

152

4. Geometry

SolidCAM2005 Milling Users Guide

4.3.2 Edit a Drill Geometry You can add or remove drill positions from previously saved drill geometries. 1. In the CAM Manager, right click on a Drill geometry and select Edit from the menu displayed.

2. The Drill Geometry Selection dialog is displayed. 4.3.3 Drill Geometry Selection Dialog For Drilling operations you have to dene the coordinate points where SolidCAM executes the drill cycles. The powerful selector tool enables you to dene and edit drill positions quickly and easily. Whenever you have to dene a drill geometry, the Drill Geometry Selection dialog will be displayed. You can switch between the different chain options while selecting drill points. The default option is Pick position, but you can start the chain denition with any other option.

153

SolidCAM2005 Milling Users Guide

4. Geometry

Select/Unselect drill centers You can switch between the Select/Unselect mode to dene or remove drill positions from the geometry. The Undo/Redo button will delete or restore the last selection. All the selected points will be shown in the list at the bottom of the dialog. To remove a point from the list, right click on the point name in the list and choose the Delete option from the menu or choose the Delete All option to remove all the points.

Selecting modes (Select drill centers by: ) You can add drill positions to the current geometry. The Selection eld offers three different options. Pick position. You can dene Drill positions one by one using the CAD point selection options. You can also type the coordinates (X,Y,Z) into the Edit bar and conrm each drill point by clicking on the Enter button of the Edit bar.

1. Pick drill center position - Select the drill point. 2. Conrm the selection by clicking on Enter. 3 Points on circumference. Usually, all curves and arcs of imported models are converted into splines by the exporting CAD system. Due to the nature of spline curves or surface boundaries, you cannot pick a center position like you could on a circle or arc. SolidCAM will calculate the center position of an arc dened by 3 points positioned on the spline edges. This facilitates selecting drill centers on spline surfaces. 1. Pick the first point - Pick a point on the circumference of the circle or arc using the CAD point selection options or type the X,Y,Z coordinates of the point into the Edit bar and conrm. 2. Pick the second point. 3. Pick the third point. 4. SolidCAM calculates the center of the three points and displays the drill position.

154

4. Geometry

SolidCAM2005 Milling Users Guide

Multi-positions. You can use the mouse to drag a box over the area of the model. SolidCAM will automatically recognize all arcs inside this area and select the center points as drill positions. You can also select the model face; SolidCAM will select all the drill centers on it. The options you have selected in Filter will affect the search when you apply the Multi-positions command.

1. Check whether the Filter options you have selected are correct. 2. Click on the screen to select the rst diagonal point of the box. 3. Drag a window over the area you want to select drill positions in and click on the screen to pick the second diagonal point. 4. SolidCAM will search the selected box area for drill positions and display the search result. All circle/arc centers. SolidCAM will search the visible layers for arcs and circles and add all center points as drill positions to the geometry. The options you have selected in Filter will affect the search result when using the All command. 1. Check whether the Filter options you have selected are correct. 2. Click on the All button to start the search. 3. SolidCAM will search all visible entities for drill positions and display the search result.
155

SolidCAM2005 Milling Users Guide

4. Geometry

CAD selection. SolidCAM enables you select the drill geometry with the host CAD tools. 1. Check whether the Filter options you have selected are correct. 2. Click on the CAD selection button. The Resume button will be available instead of the CAD selection button. 3. Select the geometry with the host CAD tools. 4. Click on the Resume button. Selection filter (Filter for circle/arc selection field) You can use various lters to search circles/arcs on the model for drill positions. SolidCAM will only select drill positions with the attributes set in the Filter options. You can select the following attributes:

Include Arcs. If this option is checked, SolidCAM will also include arc centers in the search for drill positions. This option can solve the occasional problem caused by imported 2D sketches that have circle entities cut to halves. It also enables you to place drills in lleted corners. All Circles. SolidCAM will search the model for circles. Arcs or broken circles will not be included in the search result. By Radius. You can limit the search by dening a radius value. Only arcs and circles with the given radius will be selected and their center position will be added to the drill geometry. You can select a radius value from the model. Click on the By Radius button. In the Select radius by: dialog you can select how you want to pick the radius from your model. Select the corresponding option and pick the radius from an existing circle/arc or use the 3 Points on circumference denition.

156

4. Geometry

SolidCAM2005 Milling Users Guide

Z-Level. You can also limit the search to a Z-level. Only arcs and circles on the given XYplane will be selected and their center position will be added to the drill geometry. You can select a Z-level from your model. Click on the Z-level button and select a point on your model using the Point selection options. The Z-coordinate of the selected point will be passed to the corresponding eld. Selected circles/arcs

No longer can be selected - This option enables you to select drills that were not selected previously. Show the Center points - This option enables you to see the drills that were picked in the previous drill geometry.

157

SolidCAM2005 Milling Users Guide

4. Geometry

4.4 3D Model Geometry

Any surface, solid or a combination of surfaces and solids can be selected as a 3D geometry. These models can be machined with the 3D Model Job in SolidCAM using various milling strategies.

4.4.1 Defining a 3D Model Geometry For 3D milling you need to build or import a model representation of your workpiece or part in the CAD system. This model describes the actual part with all the dimensions and topology information. By adding a 3D model to the CAM-Part, you enable SolidCAM to use this model to calculate the CNC tool path. 1. After you select the commands Add>3D Model, the 3D Geometry dialog will be displayed.

2. Choose the selection mode in the Type eld. You can choose the following options: Solid - to select only solid objects; Surfaces - to select surfaces only; Both - to select both surfaces and solids.
158

4. Geometry

SolidCAM2005 Milling Users Guide

The default option is Both. 3. Select the solid body.

4. The selected entities will be highlighted and the selected entity name will be displayed. In case you have chosen wrong entities, use the Unselect option to undo your selection. You can also right click on the entity name (the object will be highlighted) and choose the Unselect option from the menu. Conrm your selection by clicking on the Finish button. 5. Conrm the Default Geometry Name (see the topic 10.12.) or enter a new name for the geometry into the Geometry name dialog.

159

SolidCAM2005 Milling Users Guide

4. Geometry

4.4.2 Editing a 3D Model Geometry In the CAM module we refer to edit as adding, removing or replacing entities in 3D geometries that have been previously saved. Actual changes in dimensions or topology of your model must be performed in the CAD module. 1. In the CAM Manager, right click on the Geometry eld. Select Edit from the menu.

2. The 3D Geometry dialog will be displayed.

3. The default selection will add solids and surfaces to your model. To remove or replace solids or surfaces from your model, use the Unselect option. Click on the entities you want to add/remove from your 3D model geometry.

160

4. Geometry

SolidCAM2005 Milling Users Guide

4. In case you want to replace a model, activate the Select option and add the updated model to your geometry. 5. Conrm your selection by clicking on the Finish button. You can use the CAD selection mode to select the geometry with host CAD tools.

4.4.3 CAD selection This option enables you to select the 3D geometry with the host CAD tools. 1. Click on the CAD Selection button in the 3D Geometry dialog. The 3D Geometry dialog will be changed: 2. Select solid or surface objects (depending on the option chosen in the Type eld. 3. Click on the Resume button to nish the selection. 4. Conrm your selection by clicking on the Finish button. 5. Enter a name for the geometry into the Geometry name dialog.

161

SolidCAM2005 Milling Users Guide

4. Geometry

4.5 Wireframe Geometry

Wireframe geometry has sub-types; each with its own set of rules. All the sub-types use the same interface to select the geometry. In this lesson, the common selection methods will be explained without the special rules relevant for each sub-type. Chain geometries are dened from the following entities: edges of models, 2D curves, 3D curves, circles, lines and splines. Each chain is composed from one or more entities and denes an open or closed contour.

Wireframe Geometry

Prole
Pocket

Working Area
Slot

Limit
Section

162

4. Geometry

SolidCAM2005 Milling Users Guide

4.5.1 Defining a Profile/Pocket Geometry Chains for Profile Milling (see the topic 6.1.) can be either open or closed. You can machine one or more proles in one operation. In case you want to add more chains to the geometry, select the Add chain command again.

Closed chain

Open chain

Chains for Pocket Milling (see the topic 6.2.) must be closed. The rst chain denes the contour of the pocket. All closed chains inside the rst chain of each pocket will automatically be treated as pocket islands. Overlapping chains will be milled as separate pockets - not as islands. To select multiple pockets with islands, continue adding chains to the geometry.

Closed chain

Closed chain with island

1. After you have selected the command Add Profile, the Geometry Edit dialog will be displayed. 2. Choose the Add chain button or the Multi-chain command to dene the chains. 3. The Chain options dialog (see the topic 4.7.1.) or the Chain Selection dialog (see the topic 4.7.2.) will be displayed. 4. When you have completed the geometry denition, conrm the Geometry Edit dialog (see the topic 4.6.) with Finish. 5. Conrm the Default Geometry Name or enter a new name for the geometry into the Geometry name dialog and conrm with OK.
163

SolidCAM2005 Milling Users Guide

4. Geometry

4.5.2 Defining a Working Area Working areas are used in 3D milling (see the topic 7.2.) to constrain the machining to certain areas of the 3D model. A working area is dened by a closed chain. The chain can be either selected from points or from any 2D or 3D edges, curves or splines. As in pocket geometries, working areas can be dened with internal chains, so that the islands will be excluded from machining. In this Example the working area has been selected to re-work the radius along the cavity. Chain1 denes the outside boundary of the area; chain 2 excludes the cavity from machining.

1. After you have selected the command Add>Working area, the Chain Geometry dialog is displayed.

2. Click on the Add chain button or choose the Multi-chain mode. 3. The Chain options dialog is displayed.
164

4. Geometry

SolidCAM2005 Milling Users Guide

4. When you have completed the geometry denition, conrm the Chain Geometry dialog with Finish. In case you want to dene another working area or an island inside the previous chain, repeat the last steps. 5. Conrm the Default Geometry Name or enter a new name for the geometry into the Geometry name dialog and conrm with OK.

165

SolidCAM2005 Milling Users Guide

4. Geometry

4.5.3 Defining a Slot Geometry Chains for Slot Milling (see the topic 6.4.) can be either open or closed. You can machine one or more slots in one operation. If you want to add more chains to the geometry, select the Add chain command again. 1. After you have selected the command Add>Slot, the Chain Geometry dialog is displayed.

2. Click on the Add chain button or choose the Multi-chain mode. 3. The Chain options dialog is displayed. 4. Click on the edges or lines that make up your Slot and conrm with Finish.

5. When you have completed the geometry denition, conrm the Chain Geometry dialog with Finish. 6. Conrm the Default Geometry Name or enter a new name for the geometry into the Geometry name dialog and conrm with OK.
166

4. Geometry

SolidCAM2005 Milling Users Guide

4.5.4 Defining a Section Geometry In the Translated Surface Job (see the topic 6.5.) and Slot Job (see the topic 6.4.) you need to select a section geometry. These 2.5D jobs can be dened using 2D geometries only. With section geometries you have to dene depth proles for Slot and Translated surface jobs. Add a Section Geometry 1. After you have selected the command Add>Section, the Section Geometry dialog is displayed.

2. Click on the Add chain button. The Chain options dialog is displayed.

167

SolidCAM2005 Milling Users Guide

4. Geometry

3. Click the edges or lines that make up your Section and conrm with Finish.

4. Click on the Point button to pick the Reference point. This point denes the level of the section relative to the upper job plane. 5. Pick this point using the CAD point selection options. Conrm the Section Geometry dialog with Finish. 6. Conrm the Default Geometry Name or enter a new name for the geometry into the Geometry name dialog and conrm with OK. Edit a Section Geometry You can edit the section or re-dene the reference point of the section. 1. In the CAM Manager, right click on a Section geometry and select Edit from the menu.

2. In the Section Edit dialog, click on Point to re-pick the Reference point or Edit/Replace the section chain using the Chain options dialog. 3. Use Finish to conrm your changes and close the dialog.

168

4. Geometry

SolidCAM2005 Milling Users Guide

Settings The Settings dialog will be displayed.

This dialog enables you to dene the Spline approximation tolerance for the chain selection. 4.5.5 Defining a Limit Geometry A Translated surface job (see the topic 6.5.) can be dened using 2D geometries only. With Limit geometries you can dene boundaries for these surface jobs. 1. After you have selected the command Add Limit, the Chain Geometry dialog is displayed.

2. Click on the Add chain button or choose the Multi-chain mode. 3. The Chain options dialog is displayed. 4. Click on the edges or lines that make up your Limit and conrm with Finish.

169

SolidCAM2005 Milling Users Guide

4. Geometry

Section

Limit

5. When you have completed the geometry denition, conrm the Chain Geometry dialog with Finish. 6. Conrm the Default Geometry Name or enter a new name for the geometry into the Geometry name dialog and conrm with OK.

170

4. Geometry

SolidCAM2005 Milling Users Guide

4.6 Editing Chain Geometries

To edit a chain, press the right mouse button on the Geometry eld and select Edit from the sub-menu in the CAM Manager.

The Chain geometry dialog will be displayed.

Select a command from the menu. 4.6.1 Add Multi-chain This option enables you to create a number of chains from a model. The program will automatically create chains from the elements that are selected. For more information on this subject, please refer to topic 4.7.1. 4.6.2 Adding a Chain You can add a chain to the existing set of chains in the current geometry. The new chain will be added under the next sequential number. Dene the new chain using the Chain options dialog. For more information on this subject, please refer to topic 4.7.2.

171

SolidCAM2005 Milling Users Guide

4. Geometry

4.6.3 Chain operations All the selected chains are displayed in this dialog. To edit these chains, right click on the Chain name in the Geometry edit dialog and choose the appropriate command from the menu.

Deleting a Chain Deletes a chain from the current geometry. Replacing a Chain This command enables you to update a chain in the current chain geometry. The old chain will be deleted and you can now dene the new chain by using the Chain options dialog. Inserting a Chain This command enables you to insert a chain between two existing chains. Dene the new chain using the Chain options dialog. Editing a Chain This option enables you to edit an existing chain. The Chain options dialog will be displayed. You can reverse the chain or undo the selection steps to change the chain.

172

4. Geometry

SolidCAM2005 Milling Users Guide

4.6.4 Settings The Settings dialog will be displayed.

This dialog enables you to dene the Spline approximation tolerance for the chain selection. 4.6.5 Spline approximation SolidCAM enables you to dene the Spline approximation tolerance for the chain selection. Arcs on the XY plane are saved as arcs in the SolidCAM database; if you select an arc or spline that is not on the XY plane of the actual part home position, SolidCAM will do the following: 1. Project the arc or spline on the XY plane of the active home and divide it into segments according to the specied tolerance

Tolerance

2. In order to reduce the number of segments, SolidCAM tries to t arcs on the segments generated in step 1 according to the specied tolerance multiplied by 3.

Arc

Tolerance

Spline

173

SolidCAM2005 Milling Users Guide

4. Geometry

4.7 Chain selection

SolidCAM enables you to choose between two different tools to select a geometry:
Geometry Selection

Chain Options dialog

Chain Selection dialog

4.7.1 Chain Options dialog The chain selection options in SolidCAM enable you to select contours and boundaries quickly and easily. Whenever you have to dene a chain geometry, the Chain options dialog is displayed. This dialog is built in the SolidWorks PropertyManager. You can switch between the different chain options when dening a chain. The default option is the Curve option in the Single Entities section; you can, however, start the chain denition with any other option.

174

4. Geometry

SolidCAM2005 Milling Users Guide

Chain Direction Some of the jobs in SolidCAM use the direction of the chain geometry to calculate the tool path. In Prole Milling, for example, you have to specify the tool side, which is relative to the direction of the selected contour. The edges or sketch segments that you selected will be highlighted. The arrow at the start point of the chain indicates the direction of the chain.
Direction arrow Start Point

Use the Reverse command to reverse the direction of the chain - during or after the chain selection, if necessary. Single Entities You can dene the contour by selecting edges, sketch segments and points on the contour. SolidCAM provides two options:
Curves

You can create a chain of existing curves and edges by selecting them one after the other. 1. Pick start curve - Select the start entity (a wireframe element or the solid model edge).

175

SolidCAM2005 Milling Users Guide

4. Geometry

2. Pick next curve - Select the next curve that belongs to the chain. The curve must be connected to the previous curve; otherwise, the following message will be displayed:

3. SolidCAM enables you to dene the tolerances to determine whether two consequent elements should be connected or not. 4. To complete the selection, select Finish from the Chain option dialog.
Associativity

SolidCAM will keep the associativity to any edge or sketch entity. Any change made to the model or sketch will automatically update the selected geometry.
Point to point

This option enables you to connect specied points; the points will be connected by a straight line.

1. Pick start point - Either enter the coordinates into the command line or pick a point. 2. Pick next point - A chain element will be created from the previous point up to this point. Either enter the coordinates into the command line or pick a point. 3. To complete the selection, select Finish from the Chain option dialog.

176

4. Geometry

SolidCAM2005 Milling Users Guide

Associativity

SolidCAM will not keep the associativity to any selected point. SolidCAM saves the X, Y and Z coordinates of the selected points. Any change made to the model or sketch will not update the selected geometry. You cannot select a point that is not on a SolidWorks entity (if you need to select such a point, add a planer surface under the model and select the points on that surface). The following rules have to be understood when using virtual line selection by the Point to Point option: 1. When you select a virtual line between two edges, the line will behave as a spring. Whenever the model is changed and synchronized, the geometry will be updated with the model. 2. When you select a sequence of more than one virtual line, only the points connected to model edges or sketch elements will be updated, but all the other points will stay xed at the dened X, Y and Z positions.
Arc by points

This option enables you to create a chain segment on an arc upto a specic point on the arc.
Second Point Third Point

First Point

1. Pick start point - Choose the point on the arc where you want to start. If this is not the rst point on the chain, go to step 2. 2. Pick next point - Choose a point on the arc that is between the rst point on the arc and the third point on the arc. 3. Pick end point - Choose the third point on the arc where you want the chain to end.

177

SolidCAM2005 Milling Users Guide

4. Geometry

Associativity

SolidCAM will not keep the associativity to any selected arcs by points. SolidCAM saves the X, Y and Z coordinates of the selected points. Any change made to the model or sketch will not update the selected geometry. Auto Select SolidCAM will automatically nd the chain entities and try to close the chain contour. The Auto select mode offers the following three different options:
General chain

SolidCAM will highlight all entities that are connected to the last chain entity. You will have to select the entity along which you want the chain to continue.

Constant-Z

This option will identify only entities on the same XY-plane with the previously selected chain entity. You will be only prompted to identify the next chain element when two entities on the same Z-level are connected to the chain. The system tolerance for this option can be set in the CAM settings.

178

4. Geometry

SolidCAM2005 Milling Users Guide

Delta-Z

When you select this option, you will be required to enter a positive and negative Z deviation into the Delta-Z dialog. Only entities inside this range will be identied as the next possible entity of the chain.

1. Pick start curve - Select the start entity of the chain. 2. Pick point in chain direction - Indicate the chain direction by choosing a point on the selected start entity of the chain. 3. You will be prompted to Select one of the possible curves if the system detects that more than one entity could be the next element of the chain; indicate your choice. 4. When the system can close the chain, you are asked whether it is OK to accept; choose Yes to accept. If you answer No, you can edit the chain selection in the Chain options menu. You can, for example, undo the last step or cancel the chain selection. Auto to Point The chain is selected by specifying the start curve, the direction of the chain and the vertex upto which the chain will be created. This command is useful if you do not want to dene a closed chain, but an open chain upto a certain point. The Auto to Point selection offers three different options:
General chain

SolidCAM will highlight all entities that are connected to the last chain entity. You will have to select the entity along which you want the chain to continue.

End Point

179

SolidCAM2005 Milling Users Guide

4. Geometry

Constant-Z

This option will identify only entities on the same XY-plane with the previously selected chain entity. You will be only prompted to identify the next chain element when two entities on the same Z-level are connected to the chain. The system tolerance for this option can be set in the CAM settings.
End Point

Delta-Z

When you select this option, you will be required to enter a positive and negative Z deviation into the Delta-Z dialog. Only entities inside this range will be identied as the next possible entity of the chain.

1. Pick start curve - Select the start entity of the chain. 2. Pick point in chain direction - Indicate the chain direction by picking a point on the selected start curve of the chain. 3. Pick target vertex on chain - Select the end point of the end entity of the chain. 4. You will be prompted to Pick one of the possible curves if the system detects that more than one entity could be the next element of the chain; indicate your choice. 5. Conrm your chain with Finish in the Chain option dialog.

180

4. Geometry

SolidCAM2005 Milling Users Guide

Edit Chain
Reverse

This option enables you to reverse the direction of the chain you are currently working with. The direction is indicated by an arrow at the chains start point.
Undo step

This option enables you to undo the last selection of a chain element. Finish Conrms the selection of the chain and proceeds to the next step. 4.7.2 Chain selection dialog The Chain selection dialog enables you to choose a number of chains from a model by selecting the model elements. The program will automatically create chains from the selected elements.

Mode:

Select - This mode enables you to select the elements to dene the chains. Unselect - This mode enables you to unselect elements that were previously selected.
181

SolidCAM2005 Milling Users Guide

4. Geometry

Type Edges

When this eld is activated, SolidCAM enables you to choose model edges to build a chain geometry.
Text

When this eld is activated, SolidCAM enables you to choose text to build a chain geometry.
Selection Filter

When this eld is activated, it enables you to select only the elements that are on a specic Z level. You can enter the Z level value in two ways: either enter the value in the dialog window or press the On Z-Level button. On Z-Level - Pressing this button will enable you to choose the Z level directly from the model.
CAD selection

With this button, SolidCAM enables you to select a geometry for chains with the Host CAD tools.
Get All

This button enables you to choose all the elements.

Sort Types

When there is more than one chain, this option will enable you to determine the chain you would like to start from. The Sort chains dialog will be displayed (see the topic 4.7.4).
Chains Direction

This option enables you to determine the cutting direction of each chain. The Chains direction dialog will be displayed (see the topic 4.7.3).

182

4. Geometry

SolidCAM2005 Milling Users Guide

View Chains

The View Chains option enables you to see the chains before they are created.
Build Chains

After you select the chains you need, you can use this option to create the chains. 4.7.3 Chains direction The Chain direction option enables you to determine the direction of the chain.

Select open chain with: This option is used in cases where the chain being used is an open chain. Direction to center: The chain start point will be the end of the chain furthest from the given center point. Direction from center: The chain start point will be the end of the chain closest to the given center point.

183

SolidCAM2005 Milling Users Guide

4. Geometry

Change center position:

Tagging this will enable you to choose the center position either by entering an X and Y value or by picking a point on the model. If you do not change the center position, the home position will be used as the center point. Select closed chains: This option enables you to determine the direction of closed chains.
External chains with:

External chains are the outer borders of a pocket. You can determine if you want the chain to go clockwise or counterclockwise by choosing Direction CCW or Direction CW.
Internal chains opposite:

Internal chains are within the boundaries of external chains. By tagging this option you can have the internal chains go in the opposite direction of the external chains.

184

4. Geometry

SolidCAM2005 Milling Users Guide

4.7.4 Chains sorting

Chain sorting enables

you to decide the order in which you want the chains to be created.

By Distance The chain that is closest to the last chain will be chosen using two possible options.

From End - Start

The next chain will be the chain with the closest start point from the end point of the last chain.
Start - Start

The next chain will be the chain with the closest start point from the start point of the last chain.

185

SolidCAM2005 Milling Users Guide

4. Geometry

By Value The next chain that is closest to the last chain in a given direction will be chosen.

X start

The next chain will be the one in the X direction.

Y start

The next chain will be the one in the Y direction.

Reverse
Reverse changes the direction the chains. (X-start: Left to Right, Y-start: Upward or Downward).

Polar Chains will be chosen around a specic point. If no point is chosen, the default point is the home point of the CAM-Part.

CW Direction

The order of the chains will be in clockwise direction around the point.

186

4. Geometry

SolidCAM2005 Milling Users Guide

CCW Direction

The order of chains will be in counterclockwise direction around the point.

Change center position

The center position will be chosen either by entering X/Y values or by picking a point on the model.
Start angle

This controls the angle between the start point of the chain and the point of rotation.

187

SolidCAM2005 Milling Users Guide

4. Geometry

4.8 Operations with Geometries

You can edit and manage your geometries from the Geometry eld of the CAM-Manager. Geometries that are used by machining jobs can be edited through the CAM-Manager as they appear under the corresponding job. SolidCAM also enables you to dene and show geometries inside the job menu, so that you can select the geometry and machining strategy in one step. 1. In the CAM Manager, move the mouse on a Geometry eld and press the right button. The Geometry menu will be displayed.

2. Select the command from the menu. Show With the Show command, the 3D model, drill or chain geometry will be displayed in the active CAD window. To exit from this mode, use the Exit button in the displayed Show Geometry dialog.

Edit You can change or update the selected geometry. If the tool path of a job has been calculated, it will be deleted. You have to re-calculate the job after you make changes to the geometry.

188

4. Geometry

SolidCAM2005 Milling Users Guide

Delete/Delete All You can delete geometries that are not in use by any machining operation (job). These geometries are displayed under the Geometries symbol. Any geometry in use by jobs will appear under the respective job(s) only and cannot be deleted unless the job is deleted as well. The Delete all command is only available when you right click on the main topic symbol Geometries. It will delete all geometries not currently used by any machining operation. Whenever you click on a single geometry, the Delete command will be active for the selected geometry only. Synchronize/Check synchronization When the SolidWorks model is updated; SolidCAM enables you to check the compliance of the SolidCAM geometry to the updated SolidWorks model. If the SolidCAM geometry is not synchronized with the SolidWorks model, SolidCAM enables you to synchronize it. 4.8.1 Synchronization of the Wireframe geometry
SolidCAM Wireframe geometry

sketches.

is based on the SolidWorks model elements like edges, vertexes or

SolidWorks Model

SolidCAM Geometry based on the SolidWorks Model

When the SolidWorks model is changed, SolidCAM uses the synchronization algorithm to synchronize the SolidCAM geometry with the updated SolidWorks model.

189

SolidCAM2005 Milling Users Guide

4. Geometry

SolidWorks Model is changed, SolidCAM Geometry have to be updated

SolidCAM Geometry is updated

Synchronization check SolidCAM marks all the SolidWorks entities used for the geometry denition with a tag. The list of these tags is saved. The tags enable SolidCAM to establish a connection between the SolidCAM geometry and the SolidWorks model entities. The relations between the tagged SolidWorks geometry and SolidCAm geometry is saved in the geometry le *.gem.

SolidCAM Geometry

Tag

Tag

Tag

Tag

SolidWorks Model
SolidCAM enables you to check the synchronization status automatically or manually depending on the Synchronization settings (see the topic 10.11.). When you need to check the synchronization status of the geometry manually, do the following steps:

190

4. Geometry

SolidCAM2005 Milling Users Guide

1. Right click on the Job or Geometry name in the SolidCAM Manager. 2. Choose the Check Synchronization item from the menu.

SolidCAM checks all the geometry entities in the following method: SolidCAM compares the SolidWorks model elements geometrically against the relevant entity in the SolidCAM geometry le. If SolidCAM determines a mist between the SolidWorks model and the SolidCAM geometry, this geometry will be marked with a synchronization mark . If there is a gap or overlapping entities, SolidCAM will mark this geometry with a synchronization mark .

The synchronization mark enables us to see the problematic geometries and solve the not synchronized geometries.

191

SolidCAM2005 Milling Users Guide

4. Geometry

Geometry synchronization When the geometry has to be synchronized (the geometry marked with the synchronization mark) SolidCAM enables you to do the following steps to synchronize the geometry. 1. Right click on the Geometry name in the SolidCAM Manager. 2. Choose Synchronize from the menu.

or 1. Right click on the Job name in the SolidCAM Manager. 2. Choose Synchronize (the Synchronize & Calculate command enables you to synchronize the Job geometries and calculate the tool path) from the menu.

All the SolidCAM geometries used in the Job will be synchronized.

192

4. Geometry

SolidCAM2005 Milling Users Guide

During the synchronization, SolidCAM tries to update the SolidCAM geometry according to the updated SolidWorks model. SolidCAM nds the updated edges according to the saved tags data and tries to re-create the geometry chain. SolidCAM recognizes gaps between geometry entities and closes them.
SolidCAM Geometry

SolidWorks Model

Gap Area

SolidCAM will close the gaps by using the smallest number of entities. SolidCAM has two methods of closing gaps: If the original geometry entities are in a plane and the plane is the same as the home plane, SolidCAM will try to close the gap with entities in the same plane only. If the original geometry entities are not on a plane, SolidCAM will use a random search algorithm that will close the gap in the geometry. This search algorithm can nd different solutions to close the same gap; this depends on the sequence of the entities involved in the loops that connect to the geometry entity. The geometry that cannot be updated will be marked with an exclamation mark .

You have to edit such geometries and manually update the problematic chains. SolidCAM will not nd new chains that are not directly connected to old chains. The number of chains in the geometry will stay the same. For example, SolidCAM will not nd a new island in a pocket geometry.

193

SolidCAM2005 Milling Users Guide

4. Geometry

4.8.2 Synchronizaton of the 3D Model geometry The calculation of the tool path for the 3D Model geometry is based on a facet model produced for the whole SolidWorks model.

SolidWorks Model

SolidCAM Geometry

When SolidCAM nds that the solid has changed, it does not need to know what has changed; it simply recalculates the facet model.

Updated SolidWorks Model

Updated SolidCAM Geometry

Synchronization check SolidCAM enables you to check the synchronization status by comparing the SolidWorks model and the SolidCAM 3D Model geometry. SolidCAM enables you to check the synchronization status automatically or manually depends on Synchronization settings. When you need to check the synchronization status of the geometry manually, do the following steps: 1. Right click on the Job or Geometry name in the SolidCAM Manager. 2. Choose the Check Synchronization item from the menu.

194

4. Geometry

SolidCAM2005 Milling Users Guide

If a difference between them was found, SolidCAM marks the Geometry and related Jobs with the synchronization mark .

Geometry synchronization When the geometry have to be synchronized (the geometry marked with the synchronization mark) SolidCAM enables you to do the following steps to synchronize the geometry. 1. Right click on the Geometry name in the SolidCAM Manager. 2. Choose Synchronize from the menu.

or 1. Right click on the Job name in the SolidCAM Manager. 2. Choose Synchronize (the Synchronize & Calculate command enables you to synchronize the Job geometries and calculate the tool path) from the menu. All the SolidCAM geometries used in the Job will be synchronized. During the synchronization,SolidCAM recalculates the facet model.

195

SolidCAM2005 Milling Users Guide

4. Geometry

196

Jobs
In SolidCAM, a Job is a single machining operation. A workpiece is usually manufactured using several machining steps and technologies. For each of these steps you can define a separate job. A job can be very complex, but always uses one tool, one major geometry and executes one machining type, e.g. 3D milling, profile milling or drilling. You can edit any single machining operation, change the job sequence and generate G-Code, combining and splitting the job-list of your CAM-Part.

Adding a Job Job interface Working with Jobs Job Transformations Fixture

SolidCAM2005 Milling Users Guide

5. Jobs

5.1 Adding a Job

This command enables you to add a new job to your CAM-Part. In SolidCAM a Job is a single machining operation. Normally you manufacture a workpiece using several machining steps and technologies. For each of these steps you can dene a separate job. A job can be very complex, but always uses one tool, one major geometry and executes one machining type, e.g. 3D milling, prole milling or drilling. You can edit any single machining operation, change the job sequence and generate G-Code, combining and splitting the job-list of your CAM-Part. 1. In the CAM Manager, move the mouse on the Job eld and press the right mouse button. The Job menu is displayed.

2. Move to the Add sub-menu and select the type of job you want to dene. When you add a Job after right clicking on the Job symbol, it will be added at the end of the job list. If you execute the Add Job command on an existing job, the new job will be inserted after the selected job.

198

5. Jobs

SolidCAM2005 Milling Users Guide

5.2 SolidCAM Job Interface

Every SolidCAM Job has common areas. Click on the area name on the picture below for a detailed explanation.
Geometry area Tool area Job name area Milling Levels area

Job Data
Message

Extra Parameters

Home

Mirror/Rotate Point

Job Operation buttons area

5.2.1 Home

Dene the home number. Type the home number or select it from the graphic screen by pressing the Home number button. The Home List dialog will be displayed.

199

SolidCAM2005 Milling Users Guide

5. Jobs

To get more information about the Home right click on the Home name and choose the Inquire option from the menu. The Home data will be displayed.

After the Home selection, the model will by rotated to the selected home orientation. The Home selection operation must be the rst step in the Job denition process. 5.2.2 Geometry In this section, specify the main geometry for the Job.

If you have already dened geometries for this CAM-Part, you can select a geometry from the Geometry name list eld. Show will display the model geometry in the Host CAD. Define enables you to dene a new geometry for the Job.

200

5. Jobs

SolidCAM2005 Milling Users Guide

5.2.3 Tool In the tool area of the Job screen, three major tool parameters are displayed:
Number Diameter Corner radius

Select This button enables you to edit tool parameters or dene the tool you want to use for this job. When the tool for the job is not dened, this button displays the Part Tool Table dialog which enables you to choose the tool from the Part Tool table.

Choose the necessary tool from the Part Tool Table and click on the Select button. The tool will be chosen for the Job. The Tool dialog will be displayed with the parameters of the chosen tool.

201

SolidCAM2005 Milling Users Guide

5. Jobs

When the tool for the job is dened, this button displays the Tool dialog. This dialog enables you to edit the tool parameters. You can also choose tools from the Part Tool table.

This dialog enables you to edit the tool denition.

User Tool Type

This eld shows the tool type. The tool types were dened with the Tool type names dialog. These types are the internal tool types. SolidCAM checks the possibility of a specic internal tool type to work in the selected job. Selecting a shaped tool will activate the Tool name section on the Tool topology page.

202

5. Jobs

SolidCAM2005 Milling Users Guide

Part Tool table

This button enables you to choose the tool from the Part Tool table. The Part Tool Table dialog will be displayed. The Topology page (see the topic 3.8.2.) contains the Topology Data of the tool like diameter, length, angle, corner radius etc. The Job Data page (see the topic 3.8.3.) contains the default Tool Material data, Feed and Spin data and diameter and length offset numbers. Data The Data button displays the Feed&Spin dialog. This dialog displays the tool material, feed and speed parameters and the diameter and length offset numbers used in the current job. When the tool is selected for the job, SolidCAM lls this dialog with the default data of the selected tool. The Tool Data dialog enables you to edit the tools for the specic job only.

Tool Material

The Tool Material is used to describe one or more of the following properties of the tool: Material of the tool (High Speed Steel, Carbide etc) Working conditions of the tool Use of tool (rough, nish, etc) The Tool Material is used to dene the Speed and Feed defaults. When you choose the Tool material, the feed type will be changed to Fz and the spin

203

SolidCAM2005 Milling Users Guide

5. Jobs

type to V. The Feed and Spin values are default system values since the Work material has not been dened yet. Loading the tool to a job will connect the Tool material to the Work material and the correct Feed and Spin values will be loaded from the Speed/Feed defaults table.
Spin

This eld denes the spinning speed of the tool. It denes two spin values: Spin Rate - Normal spin-rate; used in rough milling. Spin Finish - Finish spin-rate; used in nish milling. The spin value can be dened in two types of units, namely S and V. Meters/Minute in the Metric system or in Feet/Minute in the Inch system; it is calculated according to the following formula:
V = (S * PI * Tool Diameter) / 1000 S is the default and it signies Revolutions per Minute. V signies Material cutting speed in

Feed

This eld denes the feed rate of the tool. It denes three feed values: Feed XY - Feed-rate in the XY plane. Feed Z - Feed-rate in the Z direction. Feed Finish - Feed-rate used for nish milling. The feed value can be dened in two types of units, namely: F and Fz.
F is the default and it signies Units per minute. Fz signies Units per tooth and is calculated

according to the following formula:

Fz = F/(Number of Teeth * S)

For Penetration only

When this option is turned on, the dened Feed Z will be used for vertical movements only. When this option is turned off, the dened Feed Z will be used for all movements when the Z-coordinate changes. This option is active only for the 3D Model Job.
204

5. Jobs

SolidCAM2005 Milling Users Guide

Diameter Offset Number

This parameter denes the number of the Diameter Offset Register of the current tool in the Offset table of the CNC machine.
Length Offset number

This parameter denes the number of the Length Offset Register of the current tool in the Offset table of the CNC machine. 5.2.4 Job name Once you select a geometry and a tool, SolidCAM will automatically enter a default name (e.g. 3DM_

Model_T2) based on the job type, geometry name and tool number. You can then change the job name, if necessary.

TR_Profile_T1
Job type abbreviation Geometry name Tool

When you add a new job, you can use an existing job as a template for the new job. All elds of the template job will be copied and you only need to edit some changing parameters, e.g. select another geometry or surface offset. Use the Job name list eld to select the template job.

205

SolidCAM2005 Milling Users Guide

5. Jobs

5.2.5 Milling Levels

In this section you must specify the Z-levels in which the tool movements and the job will be executed. The default input to this elds are the CAM-Part values you have specied in the Home data dialog. Enter the values or use the respective buttons to pick the Z-levels from your 3D model. Clearance level is the Z-level to which the tool will retreat when moving from cut to cut. Safety distance is the distance to the Job upper plane at which the tool will start moving at the Z feed-rate you have entered for the tool. Movements from the Job Clearance plane to this height are performed in rapid move. Job Upper level is the Z-level at which the machining will start in cutting operations. Job Lower level or Depth sets the Z-level below which the tool will not mill. SolidCAM will not penetrate this plane in any milling strategy. The value of these parameters is the Z-coordinate. These parameters can be dened either by entering the value in the edit box or by picking a specic point on the solid model (except Safety distance). In the latter case, the parameters are associative to the solid model. Associativity enables SolidCAM to be synchronized with the solid model changes; SolidCAM automatically updates the CAM data when the model is modied.

206

5. Jobs

SolidCAM2005 Milling Users Guide

The following Jobs parameters are associative to the SolidWorks model.

Clearance level Job Upper Level Job Lower Level

SolidCAM enables you to dene these parameters by picking the solid model. The Depth parameter used in some Jobs (Prole Job, Pocket Job etc) is indirectly associative. You have two possibilities: To dene the Depth by manual input. To dene the Job Lower Level by picking on the model. In this case the Depth will be calculated automatically. In this case the associativity will be established in the Job Lower Level. When either the Job Upper Level or the Job Lower Level is synchronized, the Depth will be updated. The associativity will be saved only for the following picked items: Vertex Sketch Point Reference point Part Origin Planar Face parallel to the XY plane of the current Home Plane parallel to the XY plane of the current Home

207

SolidCAM2005 Milling Users Guide

5. Jobs

The Pick dialog displays the Z-coordinate of the picked point. If the value is associative to the model, the edit box will be highlighted in orange. When the parameter is dened by on-model pick, SolidCAM displays the Z-coordinate of the picked point in the related edit box. The background of the edit box will be changed. The value displayed in this edit box is associative to the solid model.

If you type in this edit box, the associativity is removed. The associative parameters are displayed in the CAM Manager under the Job name.

When the parameters are not synchronized, the parameters and the parent Job are marked with the synchronization mark.

208

5. Jobs

SolidCAM2005 Milling Users Guide

The synchronization commands are available for jobs in the right-click menu.

The Synchronize button enables you to synchronize the value of the parameters with the updated model. The Synchronize & Calculate command enables you to synchronize the parameters value with the updated model and calculate job after the synchronization. The Check Synchronization button enables you to check the model for updates affecting the specied parameter. The Break Z-Levels Associativity / Break associativity command enables you to break the associativity between Job Levels parameters and the solid model. The conrmation message will be displayed.

209

SolidCAM2005 Milling Users Guide

5. Jobs

When the synchronization fails, SolidCAM marks the job and the parameters with an exclamation mark.

The parameters denition can be edited within the Job dialog. You have to either type the necessary values or redene the points on the model. In the rst case, the associativity will be removed. 5.2.6 Extra parameters

This eld will only be activated when special job options have been implemented in the post-processor you use for this CAM-Part. Click on the Data button. The Job option dialog will be shown with the additional parameters dened in the post-processor.

5.2.7 Mirror/Rotate point If you use a Job transformation, this button enables you to dene the point around which this job will be rotated or mirrored. The Mirror/Rotate point dialog will be displayed, showing you the coordinates of the current mirror/rotate position.

1. Enter the X,Y,Z coordinates into the Edit bar and conrm with Enter or pick a position using the CAD point selection options. 2. Conrm with OK.

210

5. Jobs

SolidCAM2005 Milling Users Guide

5.2.8 Message You can type a message into this eld that will appear in the generated G-Code le.
G43G0 X-49.464 Y-38.768 Z12. S1000 M3 (Upper Face Milling) (--------------------------) (P-POCK-T2 - POCKET) (--------------------------) G0 X-49.464 Y-38.768 Z10.

5.2.9 Job operation buttons

Save

All settings and parameters of the job will be saved in your disk. The tool path, however, will not be calculated. This enables you to postpone the calculation or to calculate jobs in batches. Use the corresponding commands of the CAM Manager to calculate the job later on. In the job list, all jobs that have not been calculated are marked with an asterix (*).
Save&Calculate

All settings and parameters of the job will be saved to your disk and the tool path will be calculated. After the calculation has been performed, you can exit the Job screen and return to the CAM Manager.
Simulate

Performs simulation of the cutting process. The Job must be calculated before this option can be used.

211

SolidCAM2005 Milling Users Guide

5. Jobs

G-Code

Generates G-Code for the Job. The Job must be calculated before this option can be used.

Exit

This eld enables you to exit the job screen and return to the CAM Manager. Any changes you made in the job screen will be lost if you exit the job without prior saving.

212

5. Jobs

SolidCAM2005 Milling Users Guide

5.3 Working with Jobs

Some of the Job commands will affect all existing jobs; others can only be applied to one or more selected jobs. SolidCAM will produce different menus, depending on whether you right mouse click on the Job symbol of the CAM Manager or on an existing job in the job list of your CAM-Part. In the CAM Manager move the mouse on the Job symbol and press the right mouse button. The Job menu will be displayed.

If you press the right mouse button on an existing job, the Job commands are displayed.

213

SolidCAM2005 Milling Users Guide

5. Jobs

5.3.1 Add Job This command enables you to add a new job to your CAM-Part. In SolidCAM a Job is a single machining operation. Normally you manufacture a workpiece using several machining steps and technologies. For each of these steps you can dene a separate job. A job can be very complex, but always uses one tool, one major geometry and executes one machining type, e.g. 3D milling, prole milling or drilling. You can edit any single machining operation, change the job sequence and generate G-Code, combining and splitting the job-list of your CAM-Part. 1. In the CAM Manager, move the mouse on the Job eld and press the right mouse button. The Job menu is displayed.

2. Move to the Add sub-menu and select the type of job you want to dene. When you add a Job after right clicking on the Job symbol, it will be added at the end of the job list. If you execute the Add Job command on an existing job, the new job will be inserted after the selected job.

214

5. Jobs

SolidCAM2005 Milling Users Guide

5.3.2 Add Machining process This command enables you to use a previously created Machining process in your CAM-Part. For more information on the Machining Processes, please refer to the topic 11. 5.3.3 Edit This command enables you to view or change the denition and parameters of an existing job. If you select this command, the corresponding job screen will be displayed and you can change the job denition. 5.3.4 Calculate/Calculate All Before you will be able to generate G-Code for your CNC-machine, you have to perform the tool path calculation. Based on the geometries, machining strategy and technological parameters you have dened and saved in the Job, SolidCAM will calculate the movements of the tool. If you expect a long tool path calculation time, mainly in 3D milling jobs, it is advisable to dene your jobs, save them and postpone the tool path calculation. This function enables you to calculate large CAM-Parts with many jobs in a batch routine e.g. overnight. 5.3.5 G-Code/G-Code All The commands in this sub-menu enable you to generate, list, copy or print NC-programs. For more information on the Generating G-code, please refer to the topic 9. 5.3.6 Calculate & G-Code All This command enables you to calculate all the Jobs in your CAM-Part and produce a G-Code. 5.3.7 Simulate You can simulate and verify jobs that have been saved and calculated. For more information on the Simulation, please refer to the topic 8.

215

SolidCAM2005 Milling Users Guide

5. Jobs

5.3.8 File This option enables you to append some ASCII les with a G-Code to your CAM-Part.

5.3.9 Job Group

The Job Group in SolidCAM is the set of separate jobs with a dened order in the sequence. The Job Group menu enables you to control Job Groups.
Define Job Group

These options convert the selected Jobs into a Job Group. The Define new Job Group dialog will be displayed.

216

5. Jobs

SolidCAM2005 Milling Users Guide

1. Enter the Job Group name in the name eld. 2. Choose the type from the list. 3. You can also enter the Description - a text string that describes the Job Group. Selected Jobs will be converted into the Job Group.
Add Job Group to Machining Process table

This option enables you to insert the selected Job Group into the current Machining process table.

Remove Jobs from Job Group

This option removes the selected Job from the Job Group.
Explode Job Group

This option explodes the Job Group into single Jobs. 5.3.10 Delete/Delete all This command enables you to delete jobs from the job list of your CAM-Part. 1. Select a job using the mouse. To delete several jobs at a time, select them using the Shift and Ctrl-keys. 2. With the right mouse button, click on the jobs and select the Delete command. 3. To delete several jobs at a time, select Yes to all in the conrmation message.

217

SolidCAM2005 Milling Users Guide

5. Jobs

5.4 Managing Jobs in the CAM-Manager tree

5.4.1 Job Sequence You can change and re-arrange the sequence of the jobs in the CAM Manager. Simply drag the job to its new place in the job list.

5.4.2 Undo Sequence This command enables you to undo your last change in the sequence of the job list. 5.4.3 Split This command enables you to separate your list of jobs before the G-Code generation. If you place split marks after jobs and select G-Code All, separate NC-programs will be generated for each job or group of jobs that are located between the corresponding split mark. In this example, you will receive 5 separate G-Code les for the jobs divided by the split marks.

218

5. Jobs

SolidCAM2005 Milling Users Guide

Adding Split marks

1. Click on the job after which you want to insert a split mark. 2. Press the right mouse button and select the Split command. 3. The split mark will be inserted.
Removing Split marks

1. Click on a split mark and press the right mouse button. 2. Select the Delete command and conrm the message with Yes. Just like re-sequencing jobs, you can move a split mark to another location in the job list. Simply drag the split mark on the job after which you want to insert it. 5.4.4 Expand This command enables you to open the job list, so that all the geometries used by each job will be displayed in the tree structure of the CAM Manager. 5.4.5 Collapse This command enables you to reduce the job list, so that only the job names will be displayed in the tree structure of the CAM Manager.

219

SolidCAM2005 Milling Users Guide

5. Jobs

5.4.6 Automatic Sort

Automatic sort

enables you to sort all of the jobs that you created to work in a specic order. 1. Choose the Automatic sort item from the menu. The Automatic Sort Priority dialog is displayed.

2. Choose the desired options. 3. Click on the OK button to conrm the operation. 4. All the Jobs will be sorted in the specied order. If you press OK without choosing any of the options in the dialog window, the jobs will be sorted starting from tool number 1 and upward.
Automatic Sort options:

Home: Jobs will be sorted according to the home number. Job upper plane: Jobs started on a higher plane will come before jobs started on a lower plane. Use center drill first: All tools that were tagged as center drills will be moved to the top of the job list. Sort drill radius: Drills can be sorted according to size; either from small diameters to large diameters or from large diameters to small diameters. Move drills to end: This option will move all drills that are not tagged as center drills to the end of the job list.

220

5. Jobs

SolidCAM2005 Milling Users Guide

The following is the order of precedence if more than one option is chosen. 1. Home 2. Job upper plane 3. Use Center drill rst 4. Sort Drill radius 5. Move Drills to end Undo Sort This option will return the automatic sort to the original order.

5.5 Job Transformations

When you transform a Job or a group of jobs, commands such as move, copy, translate and rotate will insert the corresponding G-function and cycle into the G-Code le. You can check the dened transformation during the tool path simulation. In the CAM Manager, move the mouse on a Job and press the right mouse button. Move the mouse to the Transform sub-menu.

You can perform only one transform action on each job. The job transformations will only work if your CNC-machine controller supports the corresponding function.

221

SolidCAM2005 Milling Users Guide

5. Jobs

5.5.1 Init Init will cancel and reset any transformation that was performed on the Job. 5.5.2 Move This option moves a Job or a group of Jobs while offsetting them in three axes, namely: X, Y and Z. When you choose this option, the Move dialog box is displayed:

1. Enter the offset values for the X, Y and Z coordinates. 2. Conrm by clicking on OK. 5.5.3 Translate This option copies a Job or a group of Jobs according to a Matrix or List of points.
Matrix

Copies the Job to a rectangular matrix of locations. When you choose this option, the Matrix dialog box is displayed.

1. Num Rows - enter the number of Rows. 2. Num Columns - enter the number of Columns. 3. X Step - enter the delta value between each two columns. 4. Y Step - enter the delta value between each two rows. 5. Conrm with OK.

222

5. Jobs

SolidCAM2005 Milling Users Guide

List

Copies the Job to a list of Locations dened by their X, Y and Z values. The Home of the Job will be moved to the absolute X,Y,Z positions dened in the Translation list dialog.

1. Enter the values of the absolute X,Y,Z position where the Job should be executed (Separate values by comma or blank). 2. Click Enter to add the position to the Translation list. 3. Check the Include Original box, if you want to execute the job in its original position before translating it. 4. Conrm with OK. To edit a position in the translation list, enter the new values for this position into the Edit eld, click on the position you want to overwrite and then click on Enter. To delete a position from the translation list, click on the position and press the Del-key.

223

SolidCAM2005 Milling Users Guide

5. Jobs

5.5.4 Rotate This option copies a Job or a group of Jobs while rotating them. Two options are available: Delta and List. The point about which the rotation is executed is either the home position or the Mirror/Rotate point dened in the job.
Delta

A number of rotations are performed from a start angle with a uniform delta angle. The Rotate dialog box is displayed.

1. Enter the Number of Rotations. 2. Start angle - enter the start angle (+/-) relative to the positive X-axis. 3. Delta angle - enter the delta value (+/-) between two rotation steps. 4. Conrm with OK.
List

Copies the Job to a list of Angle Locations dened by their relative Angle to the positive X-axis. The Rotations list dialog will be displayed. 1. Enter the value of the angle (+/-) where the Job should be executed. 2. Click on Enter to add the angle to the list of angles. 3. Check the Include Original box, if you want to execute the job in its original position before rotating it. 4. Conrm with OK.

224

5. Jobs

SolidCAM2005 Milling Users Guide

To edit an angle in the angles list, enter the new value for this angle into the Edit eld, click on the angle you want to overwrite and then click on Enter. To delete an angle from the angle list, click on the angle and press the Delkey. 5.5.5 Mirror This option mirrors a Job or a group of Jobs around the X, Y or both axes. The Mirror dialog will be displayed.

The point around which the mirror operation will be executed is either the home position or the Mirror/Rotate point dened in the job. 1. Click on the corresponding button to dene the axis around which the jobs will be mirrored: X - mirrors around the X -axis. Y - mirrors around the Y -axis. XY- mirrors around both the X and Y-axes. Reset enables you to clear the Entry eld. 2. Check the Include Original box if you want to execute the job in its original position before mirroring it. 3. Conrm with OK.

225

SolidCAM2005 Milling Users Guide

5. Jobs

5.5.6 4th Axis This option enables you to execute 4-axis rotations of a Job or a group of Jobs. After the 4th-axis is rotated, the job will be executed again. When you choose this option, the Rotations list dialog will be displayed.

1. Enter the value of the angle (+/-) around which the 4th axis should be rotated. 2. Click Enter to add the angle to the list of angles. 3. Check the Include Original box, if you want to execute the job in its original position before rotating it. 4. Conrm with OK. To edit an angle in the angles list, enter the new value for this angle into the Edit eld, click on the angle you want to overwrite and then click on Enter. To delete an angle from the angle list, click on the angle and press the Del-key.

226

5. Jobs

SolidCAM2005 Milling Users Guide

5.6 Fixture
SolidCAM enables

you to dene the Part Fixtures such as like clamps, vises, jig plates etc

This feature enables you to get a more realistic picture during the simulation and check possible collisions between the cutting tools and xtures.

1. The Fixture is dened with the Define Fixture item from the right-click menu available on Jobs.

2. The Fixture dialog will be displayed. This dialog enables you to dene the Fixture geometry.
227

SolidCAM2005 Milling Users Guide

5. Jobs

5.6.1 Fixture dialog

Define 3d Model

This button enables you to select the 3D model for the Fixture. The 3D Geometry dialog will be displayed.

When the geometry is selected, click on the Finish button. The Geometry name dialog will be displayed.

In this dialog, conrm the Default Fixture name or type a new one. Conrm this dialog. The Fixture dialog will be displayed again.

228

5. Jobs

SolidCAM2005 Milling Users Guide

Show on Model

You can highlight the selected Fixture model in the SolidWorks window with this button.

Show

You can display the Fixture in the Rest Material window of SolidCAM with this button.

229

SolidCAM2005 Milling Users Guide

5. Jobs

When the Fixture is dened, SolidCAM adds the Fixture item to the CAM Manager. SolidCAM enables you to dene any number of Fixtures that can be used at different stages of the CAM-Part.

230

2.5D Milling
SolidCAM enables you to perform a number of standard 2.5 operations like profile, pocket, slot machining etc. These operations can be performed using 2D skethces as well as solid models. Full toolpath control and powerful algorithms ensure that the user can manufacturethe way he needs to.

Profile Job Pocket Job Drill Job Slot Job Translated surface Job

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

6.1 Profile Job

You can mill on or along a contour. The prole geometry can be either open or closed. In prole milling you can optionally use tool radius compensation to the right or left side of the geometry. SolidCAM offers two types of proling: Milling a single profile to the specied constant or variable depth in one step or in several user-dened down-steps. Concentric profiles to the specied constant or variable depth; this type of proling generates several concentric proles that start from the dened clear offset distance from the prole, and nishes on the prole geometry, thus clearing the area around the prole to a constant depth.

232

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

When you select the commands Add>Profile, the Profile Job screen will be displayed.

6.1.1 Geometry name In this section you have to specify the contour, i.e. prole geometry you want to mill.

233

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

6.1.2 Down Step SolidCAM uses the constant-Z passes for the Prole generation. With the Down Step parameter you can dene the distance between each two successive Z-levels. Enter the tools cutting depth.

Down Step Job Upper level

Profile Depth

6.1.3 Offsets

Offset on profile Enter an offset distance of the tool from the prole.
Finish offers

two possible options:

None - is used when no nish is required. The specied offset will remain on the contour. Profile - is used when you want to execute a nish cycle to remove the remaining offset from the prole.

234

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

Clear offset The Clear option will generate several concentric proles with a constant depth that start from the dened clear offset distance from the prole and nish up to the geometry of the prole, thus clearing the area around the prole. Offset denes the distance from the geometry at which the milling starts. The Clear Offset value should be equal or larger than the Offset on the prole value. The tool will start milling the prole at the distance dened by Clear Offset and will nish at the distance dened by the Offset on prole; the overlap of the adjacent tool paths is dened by the Side Step. Side Step denes the overlap of adjacent tool paths. It determines the offset between two successive concentric proles.
Side Step

Clear Offset Offset on Prole

For&Back this option enables you to create the tool path for the Clear Offset removal containing both climb and conventional movements.

Clear Offset tool path

Profile Geometry

235

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

Forward this option enables you to create the tool path for the Clear Offset removal containing only climb movements.

Clear Offset tool path

Profile Geometry

6.1.4 Fillet size for last cut

This option enables you to add a radius to a sharp corner without having to change the geometry. This option is relevant for Profile Job, Pocket Job, Slot Job (Constant section and the 3D Model Job (Roughing and Constant-Z finishing strategy).

type)

Tool path Geometry External fillets

Internal fillets

236

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

Internal

This eld controls internal corners.

External

This eld controls external corners. The maximum external llet size is dened by SolidCAM Settings (see the topic 10.3.5.). In the Profile Job, this option doesnt work with the Tool side: Middle option. 6.1.5 Define depth This option enables you to choose the depth type for the prole.
Constant

With this type SolidCAM generates a tool path with a constant depth as dened in the Milling levels area.
Variable (Define Depth)

With this option you can dene a different depth at different prole points. 1. Choose the Define depth mode. 2. Click on the Pick button. The Define depth dialog will be displayed.

With this dialog you can control the points where the depth changes.

237

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

Select/Unselect

These buttons enable you to switch between the Select/Unselect mode to dene or remove points where the depth changes. Undo - this button will delete or restore the last selection. You can specify a certain chain in the prole geometry with the combo-box with the prole number and with the Next Profile button. The Points field contains information about selected depth changing points. You can change the points properties by double-clicking the parameter in this area. Profile No. - the Prole geometry chain number. Z - the Z coordinate of the prole depth at the specied point. Type - the depth changing type.
Vertical Sloped -

the depth changes at specied points. the depth changes gradually over the tool path segment.

Depth changing points

Vertical type

Slope type

Select the depth changing point on the prole. The Depth dialog will be shown.

In this dialog specify the depth and vertical/sloped type.

238

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

6.1.6 Descent type This section determines how the tool will approach the start point of the contour. Select one of the three available descent types from the list eld. Rapid generates a rapid descent (G0) from the Clearance plane to the approach plane. You can use this option when you know that there is no material in the descent path. Feed will cause the tool to rapid to the Job upper plane minus the Safety distance. Then the tool will descent to the approach plane with the given Z Feed rate. Use this option when you know that there is material in the descent path. Diagonal can be activated only if the down step is equal to the prole depth. It will cause the tool to rapid from the Clearance plane to the Job upper plane + the Safety distance. Then the tool will diagonally descent to the start of the prole geometry at the normal feed rate. The angle of the diagonal is automatically generated depending on the type of approach you choose. enables you to pick the point on a closed prole where the tool should start to machine the prole. By default, the machining will start at one-quarter of the length of the rst chain entity. This eld is inactive if you use an open prole geometry, as the machining will then automatically start on the vertex of the rst chain entity.
Define start Default start will automatically select the start point of the prole chain geometry you have dened as the start point for the contour.

6.1.7 Rest Material/Chamfer

Rest material - This option enables you to dene parameters to remove the rest material left unmachined after previous Jobs. Chamfer - This option enables you to machine chamfers with a Center drill tool. The Rest Material dialog is available from the following jobs:
Profile Job Pocket Job

239

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

Rest material In Profile Machining, when a large tool is used around the prole, the tool will leave material in corners that it cannot enter.

Rest Material
The rest material option enables you to remove the material from this area without dening a new geometry. In the Rest Material dialog box, the following data must be given:

In this dialog you have to dene the following parameters: Previous tool diameter - The diameter of the rough end-mill that was used in the previous job. Previous wall offset - The wall offset of the previous job. Extension - The overlap distance that you would like to start and end from the previous larger end-mill.

Extension Rest Material

240

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

Milling type

Choose the milling type either as Separate areas or Around profile. In separate areas, SolidCAM generates a prole or pocket tool path to clean areas that the previous tool could not mill. The around prole strategy generates a closed prole to mill the rest material.
Separate areas

previous tool.

- with this option SolidCAM machines only areas not machined with the

Around Profile -

SolidCAM machines the whole prole.

241

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

In 3D Model and Pocket Jobs with Separate Area machining strategy, SolidCAM can generate two types of tool paths, depending on the volume of the rest material and on the previous and present tool diameters:
Pocket-style tool paths. Profile-style tool paths.

Pocket-style tool paths

Profile-style tool paths

SolidCAM generates either a pocket or prole tool path in each area of the rest material.

The options picked in this box will determine which of these tool paths will be cut: Island only tool paths that touch the Islands are cut. Island + Wall tool paths that touch both the Wall and Islands are cut. Wall - only tool paths that touch the Wall are cut.

242

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

Chamfer The Chamfer option is available only in the Prole and Pocket Jobs.

The chamfer feature in the prole and pocket job enables you to use a drill tool to add a chamfer to the edge of a part.

In the Tool area of the Prole Job screen, click on the Select button. The Part Tool Table dialog will be displayed from which you can choose the drill tool for the chamfering.

243

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

In the Milling levels section, enter the size of the chamfer edge in the Profile depth window.

Choose Chamfer from the Rest Material/Chamfer option and press the Data button.

In the dialog window that opens enter the following parameters:

Feed

- The feed rate you would like the tool to travel

Cutting Diameter

- The starting cutting diameter of the tool

Cutting diameter Profile depth (Chamfer length)

244

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

If you choose to chamfer a part that has a sharp corner, it is important that the cutting diameter is the same as the last tool used in that geometry. This will give you an equal chamfer all around.

6.1.8 Tool Side The direction of the geometry can be controlled by the chain direction and the options you use in the Prole Direction eld.
Tool Side enables

you to decide on the tool position relative to the geometry.

Right

Left

Middle

Right - The tool will cut on the right side of the prole geometry at a distance dened by the values set in Offset on profile (see the topic 6.1.3). Left - The tool will cut on the left side of the prole geometry at a distance dened by the values set in Offset on profile (see the topic 6.1.3). Middle - The center of the tool will move on the prole geometry. (NO compensation G4x can be used with this option).

245

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

Show will display the chain geometry of the prole, its direction and a circle representing the tool relative to the geometry. The display uses the current settings in the Prole direction and Tool side elds. 6.1.9 Compensation If Compensation is activated, the tool radius compensation options G4x of the CNC controller are used in the G-Code. No compensation When the compensation is turned off, SolidCAM generates a trajectory of the tool center as an offset by the tool radius from the geometry.
Tool center trajectory

Geometry

This tool center trajectory will be performed in the G-code. No compensation will be used. Radius compensation When the compensation is turned on, SolidCAM generates the trajectory of the tool center as an offset by the tool radius from the geometry.
Tool center trajectory

Geometry

246

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

At the next stage SolidCAM creates the tool path as the offset by the tool radius from the tool center trajectory. The offset will be created in the geometry direction.
Tool center trajectory

Tool path

The G-code will be created for the tool path. The radius compensation will be used in the G-code. The Offset Amount will be equal to the Tool Radius. Zero Compensation With this method, SolidCAM calculates the trajectory of the tool center as the offset from the geometry.
Tool center trajectory

Geometry

This trajectory will be used in the G-code. The radius compensation will be used. The Offset Amount will be equal to 0. Settings SolidCAM enables you to dene the type of compensation that will be used by the specic variable in the MAC-le.
Comp_by_zero_tool = N Comp_by_zero_tool = Y

In this case the Radius compensation will be used. The Zero compensation will be used.

247

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

6.1.10 Profile Direction This option controls the direction of the geometry for this particular job. Default will machine the prole in the direction the chain has been dened. Reverse changes the direction of the geometry for this job. 6.1.11 Profile extension This option enables you to extend the prole in the positive prole direction. Number of finishes - SolidCAM enables you to generate a number of nish paths to achieve the best surface quality. You can dene the number of nish paths. Distance - the extension value. 6.1.12 Approach/Retreat You can control the way the tool approaches and retreats from the prole. Select an option from the list eld and enter the Distance value for this option. None The tool approaches/retreats to the milling level exactly adjacent to the start point of the prole. Normal The tool approaches/retreats to the prole from a point normal to the prole. The length of the normal can be set in the Value eld.

Approach value

248

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

Arc The tool approaches/retreats to the prole with a tangential arc. The arc radius can be set in the Value eld.

Approach value
The Data button will be displayed. Click on the button to display the Arc approach data dialog.

Arc angle

This parameter denes the angle of the approach arc segment. The default angle value is 90; in this case SolidCAM generates an approach path of quarter arc.

249

SolidCAM2005 Milling Users Guide

6. 2.5D Milling

Approach from

With the Arc approach option the tool moves normal to the approach arc at the arc startpoint. The following options are available:
Distance

In this case the tool starts from the specied distance from the arc start-point.
Center

In this case the tool starts from the approach arc center.

Angle

Angle

Distance

Approach from Center

Approach from Distance

Tangent The tool approaches/retreats on a line tangent to the prole. The length of the tangent can be set in the Value eld.

Approach value

Normal

Point The tool approaches/retreats from a user-dened position. From this position the tool will move in a straight line to the start point of the prole. When you select this option, the Pick button will be activated and you can select a position from the CAD model.

250

6. 2.5D Milling

SolidCAM2005 Milling Users Guide

6.1.13 Trochoidal milling This option enables SolidCAM to replace the straight lines in a toolpath by circular moves with a constant radius. The Trochoidal milling button is available in the Profile Job dialog.

Potential benets include: Faster metal removal. Making the constant circular curve the only direction change enables a high feed rate to be consistently maintained. Longer tool life. The cutting edge is in contact with the material through only about 5% of the cutters revolution vs. up to 50% for more conventional cutting. Cooling of the tool is improved. 1. Click on the Trochoidal button. The Trochoidal data dialog will be displayed.

2. Choose the Trochoidal checkbox to activate the trochoidal milling option. 3. Set the Radius and Step of trochoidal movements
Radius Tool trajectory

Step

4. Conrm the data with the OK button.

251

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.2 Pocket Job

In pocket milling you have to remove material from the interior of a closed geometry. SolidCAM offers two types of pocketing: 1. When a prole geometry consists of one or more proles and none of them are enclosed or intersect with one another, each is milled as a separate pocket without islands. 2. When a prole geometry consists of several proles, any prole that is enclosed or intersected with another prole is treated as an island. You can dene an unlimited number of islands within a single pocket.

252

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

When you select the commands Add>Pocket, the Pocket Job screen will be displayed.

6.2.1 Geometry name In this section, specify which contour, i.e. pocket geometry you want to mill. 6.2.2 Down Step SolidCAM uses the constant-Z passes for the Prole generation. The Down Step parameter enables you to dene the distance between each two successive Z-levels. Enter the tools cutting depth.

Down Step

Job Upper level

Pocket Depth

253

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.2.3 Pocket Types Use the list eld to select one of 5 different Pocket types.

Choose the pocket type and click on the Data button to dene additional parameters.

SolidCAM Pocket strategies

Hatch Contour Hatch+Contour Clear Plunging pattern

Contour machines the pocket in a round pattern. Hatch mills the pocket in a linear pattern. Hatch+Finish mills the pocket in a linear pattern and cleans up the prole on each cutting depth. Clear machines an area that is half a tool diameter larger than the pocket geometry in a hatch-style linear pattern. This enables you to clean the upper face of a workpiece. Plunging pattern - the tool moves up and down in a drilling motion, traveling inside the pocket.

254

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.2.4 Hatch type This strategy enables you to machine the pocket in a linear pattern. This option is used in Pocket Job and in 3D model Job for Roughing (see the topic 7.4.) and Constant-Z nishing (see the topic 7.5.8.).
Hatch type

will create a linear raster tool path upto the pocket contour.

Click on the Data button. The Hatch Data dialog will be displayed.

Pocket Hatch Parameters

Rough & Constant-Z Hatch parameters

255

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Hatch angle SolidCAM enables you to choose one of the following options to dene the angle of hatching:
Automatic optional angle

In this case SolidCAM automatically calculates the optimal angle of hatching to expedite the machining. The tool path will always follow the length of the pocket no matter what angle the pocket is facing.

In the Automatic optimal angle option, you can change the angle by entering a different angle value in the Delta from optimal option.

256

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

User Defined angle

This option enables you to determine the angle of the tool path.

Keep cutting direction This option enables you to control the cutting direction when moving around model contours.
No. SolidCAM generates a shorter, optimized tool path by reversing some tool movements. The

milling direction may change between climb and conventional milling. The length of the tool path will not be optimized.

Yes.

257

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Cutting direction Forward this option enables you to create the tool path containing only one-directional movements. For&Back this option enables you to create the tool path containing bi-directional movements.

For&Back
Corner
None

Forward

The tool path will be formed with sharp corners between one direction and the next.

Fillet Corner

Choosing Fillet will connect each direction with a given radius allowing for a smoother transition between path directions.

258

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Exit Material This option controls tool movements between the working areas. This option is used in the Hatch and Contour strategies in the Pocket Job and the 3D model Job.
Exit material option not chosen

When the tool moves from one working area to the next, it moves through the full material around the island to get to the next working area as shown above.
Exit material option chosen

When the Exit Material option is chosen, the tool exits the material and travels rapidly above the material to the next working area as shown above. The approach path will be the approach you chose.

259

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Plunging This option is relevant only for the Hatch strategy in the Pocket Job.

With this option SolidCAM enables you to combine the traditional hatch strategy with modern plunging technology. The Plunging dialog will be displayed (see the topic 6.2.8). Trochoidal Milling This strategy enables you to change straight tool movements with trochoidal movements. Click on the Trochoidal button. The Trochoidal data dialog (see the topic 6.1.13.) will be displayed to specify the necessary parameters.

6.2.5 Contour type With the Contour strategy, the tool moves on parallel offsets to the pocket contour.

Click on the Data button. The Contour Data dialog will be displayed. This option is used in the Pocket Job and in the 3D model Job for Roughing and Constant-Z nishing.

260

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Pocket Contour Parameters

Rough Contour parameters

Constant-Z Contour parameters

Exit material This option controls the tool movements between the working areas.

261

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Connect islands Choosing the Connect islands option enables you to keep the same cutting direction (conventional or climb milling) throughout the entire tool path where possible. This is particularly important in highspeed cutting.

Start from:
Inside

This option allows you to work in a pocket area starting from the middle of the pocket and cutting towards the outside border of the pocket.
Outside

This option allows you to work in a pocket area starting from the outside border of the pocket and cutting towards the middle of the pocket.

262

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Corner
None

The tool path will be formed with sharp corners between one direction and the next.

Fillet Corner

Choosing Fillet will connect each direction with a given radius allowing for a smoother transition between path directions.

Min corner radius.

SolidCAM enables you to dene the minimal value of the corner radius. If the given radius is too big for a specic corner, it will produce the biggest possible radius at that point. There are times were the llet option might leave some material. This is particularly true if the given radius is large.

263

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Smooth Corner

The Smooth Corner option is another cornering option that ensures that the connecting points on the path will be cleaned using a smooth transition. The tool path will form a loop in the corner, preventing an abrupt change of direction.

Sharp Corner

The Sharp Corner option ensures that using a short and simple movement will clean the connecting points on the path. Although this produces a sharp movement by the tool, the path itself is slightly shorter than the smooth corner option. This can help cut down on machining time.

This option is not recommended for high-speed cutting.

264

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Direction Enables you to choose climb or conventional milling for the roughing operation.

Climb Milling

Conventional Milling

Arc approximation This command enables you to create G2/G3 G-Code output from Contour rough operations. SolidCAM checks whether successive points of the calculated tool path can be connected using an arc or circle. If an arc or circle connection within the specied arc approximation tolerance can be made, you will receive arc and circle interpolation commands G2 and G3 in the generated G-Code. This feature can drastically reduce the number of lines in G-Code les. Most CNC-controllers and machines work much faster on arcs and circles than on single tool path points or splines. Arc approximation will increase actual feed rates on older CNC-machines and the machine will work smoother. The Tolerance value denes the tolerance SolidCAM uses to position tool path points on arcs or circles.

265

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Adjacent tool path connection This option enables you to choose the method that the tool will move within a pocket from one tool path to the next.
Linear connection

This will move the tool in a normal approach from one tool path to the next.

Rounded connection

This will move the tool in an arc path from one tool path to the next. The size of the arc is half the distance between tool paths.

266

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Plunging This option is relevant only for the Contour strategy in the Pocket Job.

With this option SolidCAM enables you to combine the traditional contour strategy with modern plunging technology. The Plunging dialog will be displayed (see the topic 6.2.8.). Trochoidal milling This strategy enables you to change straight tool movements with trochoidal movements. Click on the Trochoidal button. The Trochoidal data dialog (see the topic 6.1.13.) will be displayed to specify the necessary parameters.

267

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.2.6 Hatch+Finish type With this option, SolidCAM rst machines the pocket on the actual down step with the Hatch technology and then makes a nal path around the pocket contour.

Hatching

Final profiling

Click on the Data button. The Hatch Data dialog will be displayed.

For more information on the Hatch Data dialog, please refer to the topic 6.2.4.

268

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.2.7 Clear type This option enables SolidCAM to machine an area that is half a tool diameter larger than the pocket geometry in a hatch-style linear pattern. This enables you to plane the upper face of a workpiece. Existing pocket islands will be ignored and the whole pocket area will be cleared.

Click on the Data button. The Hatch Data dialog will be displayed.

For more information on the Hatch Data dialog, please refer to the topic 6.2.4.

269

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.2.8 Plunging Pattern is a totally different concept of removing material from a given pocket with a special tool. Instead of milling the material, the tool moves up and down as in a drilling motion, traveling along the path type you choose.
Plunging

Click on the Data button. The Plunging Data dialog will be displayed.

270

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Drill cycle type SolidCAM enables you to choose preferable drilling cycles for the plunging operation. 1. Click on the Drill cycle type button and choose the cycle type you want in the Drill cycle dialog. 2. Click on the Data button and specify the parameters in the Drill options dialog. For more information on the Drill cycles, please refer to the topic 6.3.4. Clean condition This determines the maximum percentage of material that will be removed based on the diameter of the tool. Minimal clean condition This determines the minimum percentage of material that will be removed based on the diameter of the tool. Feeds The plunging feeds can be determined by the percentage of the tool and the diameter of the tool being used.
Full/Center:

If the full diameter of the tool is cutting, the program will use the feed and speed that was placed in the appropriate eld. In the second eld, you can determine a specic working diameter of the tool. If the working diameter from the center of the tool is greater than this value but less than the full diameter, the feed and spin rate that was entered in the appropriate eld will be used.
Overlap (%):

If none of the above conditions have been lled, then the feed and speed will be determined by the overlap of the tool.

271

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.2.9 Overlap Enter the Overlap of adjacent tool paths in the milling of the pocket. The default value is 0.65 (65%). With a tool diameter 10, this would mean a side step of 3.5 for the next tool movement.

0.5D Overlap 0.5D

6.2.10 Compensation

0.2D Overlap 0.2D

If Compensation is activated, the tool radius compensation options G4x of the CNC controller are used in the G-Code. For more information on this subject, please refer to the topic 6.1.9. 6.2.11 Offsets To rough the pocket, you have to specify various offsets on the pocket geometry.

Wall Offset. Enter the remaining roughing offset on the wall of the pocket. Island Offset. Enter the remaining roughing offset on the pockets island or islands. Floor Offset. Enter the remaining roughing offset on the oor of the pocket.

272

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.2.12 Finish

This option is relevant only in case you have specied either a wall, island or oor offset. None. Use this option when no nishing cut is required. The specied offsets will remain on the pocket contour and oor. Wall. Only wall and islands will be nished on the contour. The pocket depth will be reduced by the specied oor offset. Floor. A nish cut is executed to remove the oor offset. Specied Wall and Island offset will remain on the pocket contour. Wall+Floor A nish cut is executed to remove the wall, island and oor offsets. Wall finish The Wall finish eld has two options to control the material removal on the last nishing cut. On Offset. The nish path will be executed at an offset, equal to the sum of the tool radius and the nish offset from the tool path of the last roughing cut. This will result in a uniform cutting depth (side step) on the last cut since in pocket corners the tool will not be drawn into the material.

Offset

Offset
On Geometry. The last cutting path will be executed exactly on the pocket geometry.

R R Offset

Offset

273

Offset

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.2.13 Fillet size for last cut This option enables you to add a radius to a sharp corner without having to change the geometry. For more information on this subject, please refer to the topic 6.1.4 6.2.14 Rest Material/Chamfer

Rest material - This option enables you to dene parameters to remove the rest material left unmachined after the previous Jobs. Chamfer - This option enables you to machine chamfers with the Center drill tool. For more information on this subject, please refer to the topic 6.1.7. 6.2.15 Approach This eld controls the way the tool plunges into the material inside the pocket. Choose the Approach mode and set the approach parameters. None The tool enters the material vertically at the pocket start point automatically chosen by the SolidCAM pocket algorithm. Vertical The tool enters the material vertically at a user-dened position. From this position the tool then

moves to the pockets start point, calculated by the pocket algorithm. Use the Pick button to specify the position where the tool plunges into the material.

274

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Angle

The tool moves to the pockets start point at a specied ramp angle. The start point must be selected using the Pick entry point button. Enter the approach angle into the Angle edit eld. SolidCAM does not check the approach movement against the pocket contour. Check the tool path simulation to make sure that the tool does not gouge the pockets walls or islands. Helical

Click on the Data button to set the helical approach parameters.

275

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Tool with Center cutting capabilities

If your cutting tool has Center cutting capabilities, select Center cutting. In the Angle eld, enter the descent angle that you would like the tool to follow. In the Radius eld enter the radius of the tool path. The working order will be as follows: The Helical Approach will descend from the safety distance above the Job upper plane to the material in a circular motion until the down step is reached using the user-dened radius. When the tool reaches the down step depth, it will then machine all the material at the down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the helical approach to the next working depth. This process will repeat itself until the nal depth has been machined.
Tool without Center cutting capabilities

If the cutting tool does not have Center cutting capabilities, leave the Center cutting eld empty. In the Tool down step eld, enter the depth of the down step of the tool. The result of this action is the same as with a center cutting tool except for the following differences: The tool descends from the safety distance above the Job upper plane to the material in a circular motion up to the Tool down step. At this point the tool will clear a circular path. It will then descend to the next Tool down step. This will be repeated until the tool reaches the CAM-Parts down step depth. When the tool reaches the down step depth, it will then machine all the material on that down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the helical approach to the next working depth. This process will repeat itself until the nal depth has been machined.
276

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Linear

The Linear approach follows the same rules as the Helical approach. The difference is that the descent will be in a linear zigzag fashion rather than a circular one.

Tool with Center cutting capabilities If your cutting tool has Center cutting capabilities, select Center cutting. In the Linear dialog window enter the length of the linear tool path that you would like the tool to travel. The working order will be as follows: The Linear Approach will descend from the safety distance above the Job upper plane to the material in a zigzag motion based on the user dened angle and length until the down step is reached. When the tool reaches the down step depth, it will then machine all the material on that down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the helical approach to the next working depth. This process will repeat itself until the nal depth has been machined.

277

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Tool without Center cutting capabilities If the cutting tool does not have Center cutting capabilities, leave the Center cutting eld empty. In the Tool down step eld, enter the depth of the down step you want the tool go to. The result of this action is the same as with a center cutting tool except for the following differences: The tool descends from the safety distance above the Job upper plane to the material in a zigzag motion up to the Tool down step. At this point the tool will clear a straight linear path. It will then descend to the next Tool down step. This will be repeated until the tool reaches the CAM-Part down step depth. When the tool reaches the down step depth, it will then machine all the material on that down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the helical approach to the next working depth. This process will repeat itself until the nal depth has been machined. 6.2.16 Retreat This eld controls the movement of the tool when it leaves the pocket contour on the nishing cut. None On the last point of the contour, the tool exits vertically in rapid move. This option causes the tool to exit while in contact with the pocket wall, which might cause gouging and could result in visible marks on the workpiece.

278

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Normal With a movement normal to the pocket contour, the tool retreats from the last point of the prole. The length of the normal must be specied using the Distance value. The tool then rapids vertically to the Job Clearance plane.

Retreat value
Arc With a circular motion, tangent to the last entity of the pocket contour, the tool retreats from the prole. The radius of the arc must be specied using the Distance value. The tool then rapids vertically to the Job Clearance plane.

Retreat value

The Data button will be displayed. Click on the button to display the Arc retreat data dialog.

279

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Arc angle

This parameter denes the angle of the retreat arc segment. The default angle value is 90; in this case SolidCAM generates an retreat path of quarter arc.
Retreat from

With the Arc retreat option the tool moves normal to the retreat arc at the arc startpoint. The following options are available:
Distance

In this case the tool starts from the specied distance from the arc start-point.
Center

In this case the tool starts from the retreat arc center.

Angle

Angle

Distance

Retreat from Center

Tangent

Retreat from Distance

The tool retreats from the pocket wall in a movement tangent to the last prole entity. The length of the tangent must be entered in the Distance eld.

Approach value

Normal

SolidCAM does not check the retreat movements against the pocket contour. Check the tool path simulation to make sure that the tool does not gouge the pockets walls or islands.

280

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.3 Drill Job

This job enables you to perform drills and other canned drill cycles. SolidCAM supports the canned drill cycles provided by your particular CNC Machine such as threading, peck, ream, boring etc... If your CNC Machine has no canned drill cycles of its own, they can be dened using the General Pre and Post-processor program (Gpptool).

281

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

When you select the commands Add>Drill, the Drill Job screen will be displayed.

6.3.1 Geometry name In this section, specify the drill positions, i.e. drill geometry you want to use. 6.3.2 Tool In addition to the standard tool options described earlier, SolidCAM enables you to label a tool as a center drill. This option is used for automatic sorting. In automatic sorting, tools that are labeled as center drills can be automatically moved to the top of the job list. 6.3.3 Drill depth This parameter denes the nal depth of the drill.

Drill Depth

282

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.3.4 Drill cycle type Click on the Drill cycle type button. The Drill canned cycles supported by the post-processor of the current CNC-controller will be displayed. Click on one of the icons to select the canned cycle you want to use in this job.

SolidCAM Drilling cycles

Drilling F_Drill Peck Tapping Boring R_Boring

R_Boring

Drill canned cycles must be dened in the *.mac and *.gpp post-processor of the currently active CNC-controller in your CAM-Part. Contact customer support to learn more about customizing your post-processor.

283

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Drilling

With this option the drill will travel in one single motion to the specied depth and retract. F_Drill

With this option the drill will travel in one single motion to the specied depth, pause for a specied amount of time and then retract.

Delay

In the Delay eld, enter the amount of time (in seconds) you want the tool to pause at the depth point of the hole. Peck

When you choose the Peck Data button, the Peck data dialog box is displayed. You are prompted to enter the Down step, Release distance and to choose the Release type.

Down Step

This eld determines the value of each down step of the drill.
Delay

In the Delay eld, enter the amount of time (in seconds) you want the tool to pause at the depth point of the hole.
284

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Tapping

With this option the tap will travel in one single motion to the specied depth and then retract reversing its spin direction. Boring

With this option the boring tool will travel in one single motion to the specied depth, stop its spin motion and retract rapidly. R_Boring

With this option the boring tool will travel in one single motion to the specied depth, stop its spin motion, pause for a specied amount of time and retract rapidly.

Delay

In the Delay eld, enter the amount of time (in seconds) you want the tool to pause at the depth of the hole. F_Boring

With this option the boring tool will travel in one single motion to the specied depth and retract at the same feed rate it entered.
Delay

In the Delay eld, enter the amount of time (in seconds) you want the tool to pause at the depth of the hole.

285

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.3.5 Sequence of drill positions You can select one of 3 available options to control the sequence of the drill positions.
Default

The drills will be performed according to the order in which the drill points were picked during the geometry denition.
Line

You have to dene a direction by selecting two points on your model. The drill positions will then be arranged along this Direction line.

1. Click on the Pick line button. 2. Pick first point: Enter the X,Y,Z coordinates into the Edit bar and conrm with Enter or pick a position using the CAD point selection options. 3. Pick second point: Select the end point of the direction line. 4. Use the show button to evaluate the result of the sort by line operation.

286

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Distance

This option minimizes the length of the necessary tool movement. The rst drill will be performed on the rst point dened in the drill geometry. Any other drill will be executed on the nearest position, i.e. within the shortest distance to the previous drill position.

287

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.4 Slot Job

This job generates a tool path along the centerline to the right or to the left of one or more proles. Two types of slots can be dened: The job Slot with constant depth machines the slot in several down steps until it reaches the nal depth. In Slot with variable depth, the depth prole is also dened by a 2D section. The slot can be pre-machined using rough and semi-nish cycles. The nish cut will produce a tool path according to the specied scallop height on the oor of the slot. With available parameters for a right and left extension and side step, you can mill a slot wider than the tool diameter.

When you select the commands Add>Slot, the Slot Job screen will be displayed.

288

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.4.1 Geometry name In this section, specify the contour, i.e. prole geometry you want to mill. 6.4.2 Depth type There are two methods to dene the depth of the slot. Select the depth type Constant or Section and click on the Data button to enter additional parameters.

SolidCAM Slot depth types Constant

6.4.3 Constant Depth type This option will produce a slot with a uniform depth. The Constant Data dialog will be displayed.

Section

289

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Technology parameters
Tool side

Specify on which side of the slot prole you want to mill. The tool side is always relative to the direction of the slots chain geometry.

Right. The tool will cut on the right side of the prole geometry at a distance dened by the value in the Profile Offset. Left. The tool will cut on the left side of the prole geometry at a distance dened by the value in the Profile Offset. Middle. The center of the tool will move on the prole geometry. (The cutter radius compensation G4x cannot be used with this option). The Profile offset will remain on the left/right side of the prole after machining. If Compensation is activated, the cutter radius compensation options G4x of the CNC controller are used in the G-Code. Cutting direction Forward this option enables you to create the tool path containing only one-directional movements. For&Back this option enables you to create the tool path containing bi-directional movements.

For&Back option

Forward option

290

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Slot extension This option enables you to extend the end of the slot without additional geometric construction and without editing the slot geometry. Distance. This parameter controls the slot extension. Fillet size for last cut This option enables you to add a radius to a sharp corner without having to change the geometry. For more information on this subject, please refer to the topic 6.1.4. Slot levels Depth. Enter the depth of the slot relative to the job upper plane. You can use the Depth button to pick the Z-level from the 3D model. Down step. Enter the cutting depth for two successive cuts.

6.4.4 Section depth type When you click on the Data button, the Section Slot Data dialog will be displayed.

291

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Section geometry name The section species the depth prole for this slot job. As the geometry for this 2.5D job is designed using 2D profiles and sections, a reference point is required to indicate the position of the upper job level.
Reference point (Job Upper Level)

Section (Depth profile)

Slot Geometry

Section data
Scallop

This value determines the quality of the resulting surface on the oor of the slot. The smaller the value, the smoother the surface will be.
Descent Angle

The tool will plunge into the material with the given ramp angle. The default value of 90 degrees causes a normal approach into the material. The tool enters the material at an angle to the rst slot prole. If the tool path length required to perform the ramp angle is longer than the slot prole, SolidCAM will generate a zig-zag movement to plunge into the material. Rough, Semi-finish and Finish cycles
Rough cycle

If you check this option, a rough operation will clear the slot before the semi-nish operation is performed. Enter the Down step between two successive cuts during roughing. Dene the remaining offset that will remain on the slot walls and oor after the roughing cut in the eld Rough/Semi-finish offset.

292

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Finish cycle

Check this option if you intend to semi-nish and/or nish the slot. Use the List field to select the cycles you want to perform.

Semi-finish will prepare the slot at an offset specied in the eld Rough/Semifinish offset. Finish will machine the slot to its nal dimensions and specied surface scallop. Both. Use this option to machine the slot with a semi-nish rst and then a nishing cut.
Offset for Rough/Semi-finish. This value species the offset that remains on the slot after

the rough and semi-nish operations. This offset will be removed in the last nish cut.

Tool Parameters Use the List field to specify on what side of the slot prole you want to mill. The tool side is always relative to the direction of the slots chain geometry.

Right. The tool will machine on the right side of the slot geometry. The cut will leave material on the prole equal to the specied Offset in the prole value. Left. The tool will machine on the left side of the slot geometry. The cut will leave material on the prole equal to the specied Offset in the prole value. Middle. The center of the tool will move on the prole geometry. With additional parameters for the right and left extension, the Middle option enables you to machine slots that are wider than the tool diameter. The tool will use the given side step value to cut from the right to the left side. Note that the side denition is always relative to the direction of the slot prole. Check the direction of the prole with the Geometry>Show option in the slot job screen.

293

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Right extension. Enter the distance by which the slot will be extended to the right side (relative to prole direction). Left extension. Enter the distance by which the slot will be extended to the left side (relative to prole direction). Side step. Enter the tools side step in successive tool paths. Cutting direction Forward this option enables you to create the tool path containing only one-directional movements. For&Back this option enables you to create the tool path containing bi-directional movements.

For&Back option

Forward option

294

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.5 Translated Surface Job

A translated surface is generated by moving a section along a prole geometry. Limit geometries can be projected on the translated surface. You can machine the resulting translated surface inside, outside or along the limit geometry.

When you select the commands Add>Translated Surface, the Translated Surface Job screen will be displayed.

295

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.5.1 Geometry name A translated surface requires two geometries, the prole along which the section will be translated and the section geometry.

Section Geometry

Profile Geometry

The geometries in the above example will result in this Translated surface.

296

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.5.2 Define Profile Start Point

This button enables you to pick the start point of the machining in case you use a closed prole geometry only. 1. Click on the Define profile start point button. The Start point dialog will be shown.

2. Click on the start point on the closed prole. 3. Click on the Finish button to conrm the data. 6.5.3 Profile direction This option controls the direction of the prole geometry for this particular job. Default will machine the prole in the direction the chain has been dened. Reverse changes the direction of the geometry for this job. 6.5.4 Tool side The tool side determines on which side of the prole the section will be machined. Use the Show surface button to display the current tool position relative to the prole geometry. The geometry direction set in the Reverse geometry eld also affects the tool side option. Right. The tool path is generated on the right hand side of the prole geometry. Left. The tool path is generated on the left hand side of the prole geometry.

297

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.5.5 Geometry on Section The Geometry on Section option enables you to locate the section on the prole.
Start point
Start

Profile

Section Geometry Start point

Section

End point

End point
End Start point Profile

Profile Geometry

End point

Section

Start will locate the prole geometry at the start of the section and the machining will be done from the start of the section towards the end of the section. End will locate the prole geometry at the end of the section and the machining will be done from the end of the section towards the start of the section.

298

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.5.6 Constraint The Constraint option enables you to control the tool movement at the start and end of the prole/ section. Leave this option unchecked to use no constraints at all.

Both

P2 P3

No

End Profile P3

P2

Section Section P2

Section

P2 P3 No

P3 Profile

P2 P3 Both Section P3 End

P2 Section

299

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.5.7 Process type The translated surface job can be used to mill surfaces and also to engrave proles, such as text, on a translated surface.

To engrave a prole on a translated surface, you can use the translated surface job that you used to mill the surface as a Template. Simply choose Add Job>Translated Surface and select the original translated surface job from the Job Name list in the Job screen. All the geometries and parameters of the original jobs will be copied. Enter the Process type and click on the Data button to dene additional parameters.
Translated Surface Job Process Type

Surface

Engraving

6.5.8 Surface Data for Translated Surfaces When you click on the Data button, the Surface Data dialog will be displayed.

300

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Offset on surface This value causes the nal milled surface to be at an Offset from the dened surface. Offset

Section Scallop The Scallop value determines how smooth the resulting surface nish will be. The smaller the value, the smoother the surface nish will be. The value is used for both the Finish and the Semi-nish operation.

Scallop

Overlap This value denes the tool overlap for adjacent tool paths during roughing operations. A value of 0.6 means that the tool will overlap 60% to the next tool path. For a tool diameter of 10 this would result in a side step of 4. Additionally this value denes the maximum side step used in Semi-nish and Finish operations if the calculated scallop would allow a wider side step. Descent Angle The tool will plunge into the material with the given ramp angle. The default value of 90 degrees causes a normal approach into the material. The tool enters the material at an angle to the rst line or arc of the tool path. If the length required to perform the ramp angle is longer than the rst tool path movement, SolidCAM will generate a zig-zag movement to plunge into the material.

301

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Connect type For & Back. The surface is milled with both conventional and climb tool movements. Forward. The surface is milled only in one direction. This option cannot be used if you use Limits for the translated surface. Rough cycle If you check this option, a rough operation will clear the surface area before the semi-nish operation will be performed. Enter the Down step between two successive cuts during roughing. Dene the remaining offset that will remain on the surface walls and oor after the roughing cut in the eld Rough/Semi-finish offset. Finish cycle Check this option if you intend to semi-nish and/or nish the translated surface. Use the list to select the cycles you want to perform.

Semi-finish will prepare the slot at an offset specied in the eld Rough/Semi-finish offset. Finish will machine the slot to its nal dimensions and specied surface scallop. Both. Use this option to machine the slot with a semi-nish cut rst and then a nishing cut. Rough/Semi-finish offset. This value species the offset that remains on the surface after rough and semi-nish operations. This offset will be removed in the last nish cut.

302

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.5.9 Engraving Data for Translated Surface Job When you click on the Data button, the Engraving Data dialog will be displayed.

Surface offset This value causes the nal milled surface to be at an Offset from the dened surface. Offset

Section Scallop The Scallop value determines how smooth the resulting surface nish will be. Use smaller values for a smoother surface nish. The value is used for both the Finish and the Semi-nish operations.

Scallop

303

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Overlap This value denes the tool overlap for adjacent tool paths during roughing operations. A value of 0.6 means that the tool will overlap 60% to the next tool path. For a tool diameter of 10, this would result in a side step of 4. Additionally this value denes the maximum side step used in Semi-nish and Finish operations if the calculated scallop would allow a wider side step. Descent Angle The tool will plunge into the material with the given ramp angle. The default value of 90 degrees causes a normal approach into the material. The tool enters the material at an angle to the rst line or arc of the tool path. If the length required to perform the ramp angle is longer than the rst tool path movement, SolidCAM will generate a zig-zag movement to plunge into the material.

6.5.10 Limits A limit is a prole geometry that can be used to dene additional 2D proles on the surface and to exclude areas on the surface from machining. If you would like to use a limit on your translated surface, check the Limits option and click on the Data button. To use the Engraving process type, you must specify the Engraving geometry and additional parameters in the Engraving Limit dialog.
Translated Surface Job Limit Type

Surface

Engraving

304

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

6.5.11 Limit Data for Translated Surface When you click on the Data button, the Limit Data dialog will be displayed.

Section Profile

Limit

Profile
The geometries in the above example will result in this Translated surface with Limits.

305

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Geometry name In this section, specify which contour, i.e. prole geometry you want to use as the Limit. Note that the Limit geometry must be closed. Machining area
Outside Limit geometry.

The area of the translated surface outside the limit will be machined.
Inside Limit geometry.

Only the area inside of the limit geometries will be machined. Offset on Limit geometry After machining, the CAM-Part will have remaining material on the limit geometry equal to this value. Finish on Limit Check this option if you intend to semi-nish and/or nish the limits on the translated surface. Use the list to select the cycles you want to perform.

Finish will machine the limit to its nal dimensions in one down step. Semi-finish will prepare the limits to an offset specied in the Offset eld with a cutting depth given in the Down step eld. Both - Use this option to machine the limit with a semi-nish cut rst and then a nishing cut. Side If the Limit geometry is composed of one or more chains, but none of the chains are placed inside another chain, the default option Both should be 1 used. SolidCAM will then use the relevant nish side depending on whether the Limit type is Outside or 2 3 Inside. In this Example, a Limit geometry contains a chain inside another chain (Chain #2 inside Chain #1) and a separate Limit chain #3.

306

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

The External option will nish all outside contours of the Limit chains, leaving the inside hole unnished.

Finish Cuts

The Internal option will nish only the inside contour of the Limit chain, leaving the outside Limit contours unnished.

Finish Cuts

The Both option will nish all inside and outside contours of the Limit chains.

Finish Cuts

307

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

Cutting direction This eld denes the cutting direction on the last nish cut. It can be either clockwise (CW) or counterclockwise (CCW). Semi-finish offset Enter the offset that will remain on the surface after the semi-nish operation. This offset will be removed in a last cut, if a nish cut has been specied. Semi-finish down step The down step denes the cutting depth of the tool on the Limit geometries used for the semi-nish operation.

6.5.12 Engraving Limit for Translated Surface Job When you click on the Data button, the Engraving Limit dialog will be displayed.

Engraving depth The depth of the engraved profile on the translated surface must be entered in the eld Job Upper plane of the main job screen. If you want to penetrate the translated surface by 1.0, you have to enter a value of -1.0 into the Job upper plane eld. In this Example, a text was dened as the Engraving Limit geometry and was engraved on a translated surface.

308

6. 2.5-Axis Machining

SolidCAM2005 Milling Users Guide

Engraving geometry In this section you have to specify the contour, i.e. prole geometry, which you want to engrave on the translated surface. Finish options
Type

This option enables you to semi-nish and/or nish the engraved prole on the translated surface. Semi-finish will prepare the engraving prole to an offset specied in the Offset eld with cutting depths given in the Down step eld. Finish will machine the engraving prole to its nal dimensions in one down step. Both. Use this option to machine the limit with a semi-nish cut rst and then a nishing cut.
Side

The tool can cut on the left/right to the prole or on the engraving geometry. Right. The tool will cut on the right side of the prole geometry up to a distance dened by the Offset value. Left. The tool will cut on the left side of the prole geometry at a distance dened by the Offset value. Middle. The center of the tool will move on the prole geometry.
Offset

You can specify the offset from the engraving geometry for a Semi nish operation on the left or right side of the geometry. This offset will be removed by the Finish cut, if you had dened one.
Down step

This value denes the successive Z-cutting depth during the Semi-nish operation of the engraving prole.

309

SolidCAM2005 Milling Users Guide

6. 2.5-Axis Machining

6.5.13 Approach/Retreat You can control the way the tool approaches and retreats from the geometry. Select an option from the list eld and enter the Distance value for this option. SolidCAM enables you to use the following Approach/Retreat options
None Normal Arc Tangent

For more information on this subject, please refer to topic 6.1.12. 6.5.14 Show surface You can display the geometries and the tool to check the current settings for the prole direction, tool side etc...

310

3D Milling
SolidCAMs 3D Milling can be used both for prismatic parts and for complex 3D models. For prismatic parts SolidCAM analyzes the model and automatically recognizes pockets and profiles to be machined using Zconstant machining strategies. For molds, electrodes and prototypes, SolidCAM offers powerful 3D machining, including advanced High Speed Machining strategies and integrated rest material options. No matter how complex the model, SolidCAM provides the optimal approach and roughing strategy with superior 3D finish machining for mold and die applications. 3D Model Job Rough Strategies Semi-Finish & Finish Strategies 3D Engraving Job 3D Drill Job

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.1 3D Model Job Overview

You can perform 3-axis gouge-free machining on solid and surface models. This Job offers a wide range of roughing, semi-nishing and nishing strategies for free-form models. It can be used to manufacture molds, dies, electrodes, prototypes and other 3D Models. When you select the commands Add>3D Model, the 3D Model Job screen will be displayed. Select the 3D model geometry for the Job from the list.

312

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.2 Working Area

SolidCAM enables you to limit the tool path with a specied working area. In case a Working area is used, SolidCAM calculates the whole tool path and then removes the all tool path lines that are not inside the Working area. In the Working area eld, click on the Define button; the Working area dialog will be displayed.

If you do NOT dene a working area, a box at an offset with the width of the tool diameter will be drawn around the current 3D model. SolidCAM will apply the selected milling strategy to the complete Automatic Working Area.

Automatic Working area

Geometry boundaries

Tool

313

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.2.1 Working area dialog The Working area dialog enables you to choose the type of working area and set the Working area parameters.

SolidCAM enables you to use either one or a combination of the following three methods:

Working Area

Working area Geometry Surface Conditions Selected Faces Rest Material

314

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.2.2 Working area definition via Geometry

In this section you have to specify which working area geometry denes the machining boundaries for this job. If you have already dened working area geometries for this CAM-Part, you can select a geometry from the Geometry name list eld.

Show will display the selected geometry in the Host CAD window. Define enables you to select a new working area geometry. (For more information on the Geometry selection, please refer to section ...)

315

SolidCAM2005 Milling Users Guide

7. 3D Milling

Tool on working area This option controls how the tool is positioned relative to the boundaries of the working area. Since the working area geometry is always projected on a 2D plane, viewing the model and working area in the top view shows exactly till where the tool will machine the model. Select one of the options from the Tool on working area list eld.

Internal

The tool machines up to the boundary of the working area. The center point moves at an offset equal to the tool radius.

Working Area Geometry

Tool
External

The tool machines over the boundary of the working area by a distance equal to the tool diameter.

Working Area Geometry

Tool

316

7. 3D Milling

SolidCAM2005 Milling Users Guide

Middle

The tool machines the working area until the tool center is positioned on the working area.

Working Area Geometry

Tool
Offset value (+/-)

This value enables you to specify the offset of the tool center.

A positive offset value will enlarge the working area; a negative value will reduce the working area to be machined. To stay away from a pockets wall, for example, you can use the internal option with a small negative offset value. To avoid a tool plunging down a straight wall of a block, you can use the Middle option with offset less than tool Radius. Also, with the same result, you can use the External option with a small negative offset value.

317

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.2.3 Working area definition via Surface condition

Choose this option if you want to apply milling strategies to areas inside a specic angle range. You could, for example, machine all areas inside a working area on the model, that have an angle from 0 to 30 degrees with a Linear nish strategy. All areas from 30 to 90 degrees could later be machined in a Constant-Z job.
Minimum surface angle

This value denes the lower limit of the angle range. All areas that are more at than this angle will not be included in the working area.
Maximum surface angle

All areas on the model or inside the user-dened working area that are steeper than this angle will be excluded from machining.
Minimum Surface angle Working Area

Maximum Surface angle

318

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.2.4 Working area definition via Face selection SolidCAM enables you to dene the area of the 3D model machining with two sets of model faces: Drive faces the set of faces to be milled. The tool path will be generated only for machining of these faces. Check faces the set of faces to be avoided during the generation of the tool path. Other faces of the model will not be considered during the tool path calculation.
For example:

Check Faces

Drive Faces
Within the model shown above, SolidCAM generates the tool path only for the pocket area (green). During the calculation, SolidCAM avoids the gouging of the check faces (orange). The remaining faces will not participate in the tool path calculation. The above capability is available through the Work on selected faces area in the Working area dialog.

319

SolidCAM2005 Milling Users Guide

7. 3D Milling

Drive faces Specify the Face Geometry of Drive faces. If you have already dened such geometries for this CAMPart, you can select the geometry from the Name list eld. The Define button enables you to dene a new Face Geometry with the Choose Faces dialog. The Show button will display the Face Geometry on the SolidWorks model. Check faces Specify the Face Geometry of Check faces. If you have already dened such geometries for this CAM-Part, you can select the geometry from the Name list eld. The Define button enables you to dene a new Face Geometry with the Choose Faces dialog. The Show button will display the Face Geometry on the SolidWorks model. Choose Faces dialog This dialog enables you to select one or several faces of the SolidWorks model. The selected Face tags will be displayed in the dialog.

If you chose wrong entities, use the Unselect option to undo your selection. You can also right click on the entity name (the object will be highlighted) and choose the Unselect option from the menu. The CAD Selection option enables you to select faces with the host CAD tools. The All option enables you to select all the model faces.

320

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.2.5 Working area definition via Rest material The Rest material is what has to be machined after the previous operations in order to reach the Target model. SolidCAM automatically compares the updated material after each job stock model and the target model and generates the rest material areas. With the Cut only in rest material option you can limit the machining to the rest material.

The rest material left after semi-nishing operations with the big tool.

Working only in the rest material area.

This option will work only if the following conditions are dened in the CAMPart data dialog. The target model is dened The Update Stock model check box is marked.

321

SolidCAM2005 Milling Users Guide

7. 3D Milling

Mach. Stock Name This option enables you to use the previously generated Stock model saved in the STL format for the rest material calculation. This eld is active only when the Solid Rest material calculation method and Manual method of the Rest material update are chosen. (For more information on this subject, please refer to the topic 2.4.) Show2D This will show you a 2D boundary around the area where there is material left over. Show3D This option will show the actual material that is left on the 3D target. Tolerance The tolerance of the working area (via rest material) is a visual tool that has no effect on the actual machining.

322

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.3 Tolerance

The precision tolerances dened here will directly affect the surface quality of your model.

3D Milling Tolerance

Surface Tolerance

Toolpath tolerance
Tool curvature
Surface Curvature
Side Step

323

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.3.1 Surface tolerance This tolerance controls the maximum deviation of the mathematical representation from the original solids and surfaces of your model.

The 3D model geometry will be triangulated and the resulting facets will be saved in the le modelname.fct in the CAM-Parts folder. The triangulation is performed on the 3D model geometry when you use it for the rst time in a 3D model job. If you use the 3D geometry in another job, SolidCAM will check the tolerance of the existing *.fct le of this geometry. It will not perform another triangulation as long as the *.fct le has been created within the same surface tolerance.

324

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.3.2 Tool path tolerance SolidCAM generates the tool path in two steps: 1. SolidCAM generates a mathematical representation of the surfaces and solids of the 3D model geometry inside the given surface tolerance. The information of this triangulation process will be stored in an internal *.fct le that is similar to an STL le. 2. SolidCAM calculates the tool path using the parameters that have been specied for the tool and the milling strategy to calculate the single steps of the tool on the mathematical model created in the rst step. The result of this calculation, the *.pj p-code le, later serves as input to the generation of the actual G-Code le. During this calculation SolidCAM uses the Tool path tolerance that affects on number of single steps in the tool path (accuracy of the tool path). The tool path tolerance can be dened by the following criteria:
Tool Curvature

With this option the accuracy of the tool path depends on the Tool diameter and the specied tolerance value.
Surface Curvature

With this option the accuracy of the tool path depends on the surface curvature and the specied tolerance value.
Side Step

This tolerance enables you to control the size of a single step that will be constant during the whole tool path. A small tolerance values will result in more G-Code steps in the G-Code le, but the resulting surface will be closer to the mathematical model.

325

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.4 Roughing
Rough milling removes the bulk of material surrounding the 3D model. The material will be removed on Z-levels controlled by the Job upper plane, surface offset and down step values. To remove large amounts of material, large tools, small feeds and low tolerances are usually used. You can use three different strategies to rough machine 3D models.
SolidCAM Roughing

Hatch

Contour

Plunging Pattern

Contour and Hatch strategies perform rough cuts on constant Z-levels that are automatically calculated

using the specied values for the Job Lower plane, Surface Offset and Down step.
Plunging

is a totally different concept of removing material from a given pocket, carried out with a special tool. Instead of milling the material, the tool moves up and down as in a drilling motion, traveling along the specied path type. The strategy and technological parameters are all dened in the Rough section of the 3D model job. Select one of the strategies and specify additional parameters.

326

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.4.1 Overlap Enter the Overlap of adjacent tool paths. The default value is 0.5 (50%). With a tool diameter 10, an overlap of 0.7 would mean a side step of 3.0 for the next tool movement. Values smaller than 0.3 should be avoided.

0.5D Overlap 0.5D

7.4.2 Down step

0.2D Overlap 0.2D

SolidCAM uses the constant-Z pocketing for the roughing. With the Down Step parameter you can dene the distance between each two successive Z-levels. Enter the tools cutting depth. 7.4.3 Clean flat

SolidCAM generates a set of Z-levels with equal Down steps. Sometimes the model ledge (with the specied offset) falls between the Down Steps and cant be machined in the actual operation.

Z-levels with the equil Down Step

Model with the offset

Not machined ledges between Down Steps

327

SolidCAM2005 Milling Users Guide

7. 3D Milling

None

If this option is chosen, The tool will machine only at each down step distance. Anything in between will not be machined.
Clean flat at end of Rough

When this option is chosen, SolidCAM produces complete roughing at each down step level and then returns to the at areas that are between the down steps.
Clean flat during roughing

When this option is chosen, SolidCAM produces tool paths at the down step level. At this point the tool will machine on the at area that is located between the down steps. After completing the at area, it will then go to the next down step. 7.4.4 Offset Surface offset - a minimum offset of material in the X, Y and Z direction will remain on the model contour. The value denes the closest distance the tool can get to the model. The rough operation is performed at constant Z-levels. In addition to the specied Surface offset, the roughed model will show stairs of rest material with a height equal to the down step value. To obtain a uniform offset on the model, a semi-nish operation should be executed.

Surface Offset Model Surface

328

7. 3D Milling

SolidCAM2005 Milling Users Guide

In 3D milling of prismatic parts we often need to use the different offset values for vertical and horizontal areas. With the Wall Offset value you can dene the XY offset of any surface that is not absolutely at. To dene the Z offset to the absolute horizontal (at) surfaces, use the Floor Offset parameter.

Floor Offset
Wall Offset

Use the Wall and Flat offsets for 3D machining of prismatic parts. In 3D milling of non-prismatic parts, it is best to use surface offset and not oor and wall offsets. Set the Wall and Flat offsets to 0 and enter the desired value of the Surface offset. 7.4.5 Fillet size for last cut This option enables you to add a radius to a sharp corners of the tool path without having to change the geometry. For more information on this subject, please refer to the topic 6.1.4

329

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.4.6 Descent You can control how the tool will plunge into the material. Click on the Descent button to display the Descent dialog.

None With this type of approach the tool will plunge into the material with a normal downward movement at the specied Z-feed rate. Angle If you select the Angle approach type and enter an Angle value, the tool will enter the material with a ramp movement. The ramp will start from the given safety distance down to the model contour. If, due to the model contour, the ramp cannot be created in a straight line, the approach movement will follow the contour. When you work with small descent angles, e.g. 2 degrees, you could shorten the length of the descent movement by decreasing the safety distance value. Make sure, though, that the initial offset on the raw material allows for changing the safety distance value.

330

7. 3D Milling

SolidCAM2005 Milling Users Guide

Helical

Tool with Center cutting capabilities

If your cutting tool has Center cutting capabilities, select Center cutting. In the Angle eld, enter the descent angle that you would like the tool to follow. In the Radius eld enter the radius of the tool path. The working order will be as follows: The Helical Descent will descend from the safety distance above the Job upper plane to the material in a circular motion until the down step is reached using the user-dened radius. When the tool reaches the down step depth, it will then machine all the material at the down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the helical descent to the next working depth. This process will repeat itself until the nal depth has been machined.

331

SolidCAM2005 Milling Users Guide

7. 3D Milling

Tool without Center cutting capabilities

If the cutting tool does not have Center cutting capabilities, leave the Center cutting eld empty. In the Tool down step eld, enter the depth of the down step of the tool. The result of this action is the same as with a center cutting tool except for the following differences: The tool descends from the safety distance above the Job upper plane to the material in a circular motion up to the Tool Down Step. At this point the tool will clear a circular path. It will then descend to the next Tool Down Step. This will be repeated until the tool reaches the CAM-Parts down step depth. When the tool reaches the down step depth, it will then machine all the material on that down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the helical descent to the next working depth. This process will repeat itself until the nal depth has been machined. Linear

The Linear descent follows the same rules as the Helical. The difference is that the descent will be in a linear zigzag fashion rather than a circular one.

332

7. 3D Milling

SolidCAM2005 Milling Users Guide

Tool with Center cutting capabilities

If your cutting tool has Center cutting capabilities, select Center cutting. In the Linear dialog window enter the length of the linear tool path that you would like the tool to travel. The working order will be as follows: The Linear Descent will descend from the safety distance above the Job upper plane to the material in a zigzag motion based on the user dened angle and length until the down step is reached. When the tool reaches the down step depth, it will then machine all the material on that down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the linear descent to the next working depth. This process will repeat itself until the nal depth has been machined.
Tool without Center cutting capabilities

If the cutting tool does not have Center cutting capabilities, leave the Center cutting eld empty. In the Tool down step eld, enter the depth of the down step you want the tool go to. The result of this action is the same as with a center cutting tool except for the following differences: The tool descends from the safety distance above the Job upper plane to the material in a zigzag motion up to the Tool Down Step. At this point the tool will clear a straight linear path. It will then descend to the next Tool Down Step. This will be repeated until the tool reaches the CAM-Part down step depth. When the tool reaches the down step depth, it will then machine all the material on that down step depth. When the machining is completed at this depth, it will then go up to the clearance plane. At this stage it will reposition itself at the Z safety distance above the previous down step depth and repeat the linear descent to the next working depth. This process will repeat itself until the nal depth has been machined.
333

SolidCAM2005 Milling Users Guide

7. 3D Milling

Go to clearance plane between Z steps This option enables you to control the height, where the horizontal rapid movement will be performed.

Clearance plane

When the option is turned on (default state), SolidCAM performs the horizontal rapid movements on the Clearance plane of the Job. When the option is turned off, SolidCAM performs the horizontal rapid movements on the safety distance from the last cut. SolidCAM checks for possible collisions. In areas where the rapid movements on the safety distance causes gouges, SolidCAM performs the horizontal rapid movements on the Clearance plane. Clearance plane

Safety Distance

334

7. 3D Milling

SolidCAM2005 Milling Users Guide

Drill points SolidCAM enables you to perform the approach to the material from the hole, previously machined by the 3D Drill Job (see the topic 7.7.). The 3D Drill Job has to be situated before the 3D Model Job in the CAM Manager. SolidCAM enables you to choose the geometry used for the 3D Drill Job in order to dene the approach point.

Drill point

Material to be removed

335

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.4.7.Mode (Open Pocket machining) SolidCAM locates open pocket areas and enables you to machine them with a specic strategy. This strategy enables you to combine pocket and prole tool paths in order to provide the best productivity in open pocket machining. The Open Pocket machining option is available to use within 3D Model Roughing and Constant-Z Floor machining strategy (see the topic 7.5.8.). The Mode button displays the Open pocket mode dialog.

There are three modes for open pocket machining:

Pockets

Pockets

Both closed and open areas at each down step are milled as Pockets.

336

7. 3D Milling

SolidCAM2005 Milling Users Guide

Profiles

Profiles

Closed areas at each down step are milled as Pockets. Open areas at each down step are milled by a number of equidistant Profiles from outside the model; the tool moves in parallel offsets to the contour of the section on the specied Z-Levels.

Pockets+Profile

Profile Pockets

Closed areas at each down step are milled as Pockets. If the Open areas at each down step cannot be milled completely with one Profile, then those unmilled areas are milled rst by Pocket paths and then the Profile is used for nish.

The advantage of Pockets+Profile mode over Pockets is that in narrow places it performs a Profile toolpath instead of a Pocket toolpath thus saving time. The Profiles mode is useful when you are milling a boss-type model (e.g. Core of Mold).

337

SolidCAM2005 Milling Users Guide

7. 3D Milling

Profile Approach In the Profile approach combo-box, you can select one of the following options:
None Normal Arc Tangent

The Profile approach options are the same as Approach options in the Profile Job. For more information, please refer to the topic 6.1.12. Approach open pocket from outside The Approach open pocket from outside option enables the tool to approach from outside of the material in the open pocket areas, if possible. Such an approach enables you to decrease the tool loading when plunging into the material. This option enables SolidCAM to perform the approach movement from the automatically calculated point outside of the material. The tool approaches to the necessary depth outside of the material and then plunges into the material.

In closed areas, where outside approach is impossible, the tool plunges into the material with a strategy dened in the Descent eld of the Job screen.

338

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.4.8 Rest Material With the 3D Roughing strategy, SolidCAM generates a number of sections parallel to the XY-plane of the CAMPart coordinate system. These sections are generated with a Z-step dened either by constant down-step or by scallop. In each of these sections SolidCAM uses the section prole geometry to produce a pocket tool path. The Rest material feature enables SolidCAM to machine in each of these sections only in areas where the previous tool was not able to machine. In Profile Machining, when a large tool is used around the prole, the tool will leave material in corners that it cannot enter.

Rest Material

The rest material option enables you to remove the material from this area without dening a new geometry. In the Rest Material dialog box, the following data must be given: In this dialog you have to dene the following parameters: Previous tool diameter - The diameter of the rough end-mill that was used in the previous job. Previous wall offset - The wall offset of the previous job.

Extension - The overlap distance that you would like to start and end from the previous larger end-mill.

Extension Rest Material

339

SolidCAM2005 Milling Users Guide

7. 3D Milling

Milling type

Choose the milling type either as Separate areas or Around profile. In separate areas, SolidCAM generates a prole or pocket tool path to clean areas that the previous tool could not mill. The around prole strategy generates a closed prole to mill the rest material.
Separate areas

previous tool.

- with this option SolidCAM machines only areas not machined with the

Around Profile -

SolidCAM machines the whole prole.

340

7. 3D Milling

SolidCAM2005 Milling Users Guide

In 3D Model and Pocket Jobs with Separate Area machining strategy, SolidCAM can generate two types of tool paths, depending on the volume of the rest material and on the previous and present tool diameters:
Pocket-style tool paths. Profile-style tool paths.

Pocket-style tool paths

Profile-style tool paths

SolidCAM generates either a pocket or prole tool path in each area of the rest material.

The options picked in this box will determine which of these tool paths will be cut: Island only tool paths that touch the Islands are cut. Island + Wall tool paths that touch both the Wall and Islands are cut. Wall - only tool paths that touch the Wall are cut.

341

SolidCAM2005 Milling Users Guide

7. 3D Milling

Compensation

When the eld Compensation is activated, SolidCAM will use tool radius compensation commands (G41, G42 for Fanuc) in G-Code output.
Approach

The approach and retreat on each Z-level can be controlled using the following options: None Normal Arc For more information on these options, please refer to the topic 6.1.12. 7.4.9 Hatch Roughing The model will be roughed in a linear pattern. Hatch rough will create a linear raster tool path up to the model contour.

Click on the Data button. The Hatch Data dialog will be displayed. For more information on the Hatch parameters, please refer to the topic 6.2.4.

342

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.4.10 Contour Roughing The Contour rough strategy enables SolidCAM to produce Constant-Z pockets on different Z-levels. Within the pockets, the tool moves in parallel offsets to the contour of the section of the model on each down step.

Click on the Data button. The Contour Data dialog will be displayed.

For more information on the Contour parameters, please refer to the topic 6.2.5.

343

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.4.11 Plunging pattern is a totally different concept of removing material from a given pocket with a special tool. Instead of milling the material, the tool moves up and down as in a drilling motion, traveling along the path type you choose.
Plunging

Click on the Data button. The Plunging dialog will be displayed.

For more information on the Plunging parameters, please refer to the topic 6.2.8.

344

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.5 Semi-Finish/Finish
7.5.1 Overview machining prepares the model for nishing. After semi-nishing the model, a uniform offset will remain on the material. This offset will be removed in a last nishing cut. In contrast to rough operations, in conventional semi-nishing operations higher feed rates and narrower tolerances are applied.
Semi-Finish

The same machining strategies in Finish machining can be applied for Semi-nishing. It only differs in one additional parameter, Surface Offset, that controls the X,Y and Z offset that remains on the original surface. Otherwise all strategies are dened and used in the same way as in nishing. In the Semi-Finish area, select a strategy from a list.

345

SolidCAM2005 Milling Users Guide

7. 3D Milling

Plunging SolidCAM enables you to use the special plunging strategies for semi-nishing. 1. Click on the Plunging button. 2. Set the plunging parameters in the Plunging dialog.

For more information on the Plunging parameters, please refer to the topic 6.2.8. Offsets Surface offset - a minimum offset of material in the X, Y and Z direction will remain on the model contour. The value denes the closest distance the tool can get to the model. In addition to the specied Surface offset, the roughed model will show stairs of rest material with a height equal to the down step value. In order to obtain a uniform offset on the model, a semi-nish operation should be executed.

Surface Offset Model Surface

346

7. 3D Milling

SolidCAM2005 Milling Users Guide

In 3D milling of prismatic parts we often need to use the different offset values for vertical and horizontal areas. With the Wall Offset value you can dene the XY offset of any surface that is not absolutely at. To dene the Z offset to the absolute horizontal (at) surfaces, use the Floor Offset parameter.

Floor Offset
Wall Offset

Use the Wall and Flat offsets available to set different offset values to the oor and walls only in Constant-Z machining. If you would like to use negative offsets, e.g. for plunge EDM electrode milling, the corner radius of the tool must be equal or larger than the specied offset value.
Finish

machining generates the tool path directly on the surfaces and solids of your 3D model geometry. No offset can be specied and the model will be machined to its nal topology and dimensions. You can apply a number of different machining strategies to nish your models. Each one of the strategies offers parameters to adjust the strategy to your needs. The 3D job dialog offers all three machining types, namely: Rough, Semi-Finish and Finish Milling in one screen. This enables you to perform all machining operations in one job. You will need to add another job only if the tool, milling levels or the working area is going to change from one operation to the other.

347

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.5.2 Descent You can control how the tool will plunge into the material. Click on the Descent button to display the Descent dialog.

None

When Approach is set to None or the default angle value is 90 degrees, the tool will plunge into the material with a normal downward movement at the specied Z-feed rate.

Descent: None

Tool path

348

7. 3D Milling

SolidCAM2005 Milling Users Guide

Angle along path

The tool will plunge with a ramp movement. The ramp will start from the given safety distance down to the model contour on the current Zlevel. If, due to the model contour, the ramp cannot be created in a straight line, the approach movement will follow the contour.

Angle between paths

The tool will plunge with a ramp movement. The ramp movement for the rst Z-level will start from the given safety distance. The next ramp movements will be performed between the Z-levels. If, due to the model contour, the ramp cannot be created in a straight line, the approach movement will follow the contour.

The Along between paths option is available only with Constant Z nish strategy.

349

SolidCAM2005 Milling Users Guide

7. 3D Milling

Arc

The tool will plunge using an arc movement (with a specied radius) in the vertical plane.

Descent: Arc

Tool path

This option is not available with the Constant-Z Finish strategy.

350

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.5.3 Semi-Finish/Finish strategies

SolidCAM Finishing strategies

Linear Offset cutting Spiral Circular pocket Constant Z

Pencil Milling

351

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.5.4 Linear finish strategy In linear cutting, the lines of a linear pattern are generated on a 2D plane above the model. The linear pattern is then projected on the 3D model. During this projection, the Z-position of the tool is calculated to avoid gouging of the material.

The Linear Finish dialog dialog displays parameters of the Linear Finish.

352

7. 3D Milling

SolidCAM2005 Milling Users Guide

Direction type These options control the direction of the tool on each line of the linear pattern that has been projected on the model. Different materials and cutters will require specic cutting conditions, e.g. some tools will give better surface nish when cutting only downward - in other applications you will need to use other settings to achieve optimum results.
For&Back

The tool nishes one line of the linear pattern and then directly moves to the next line and so on. It mills forward and backward without leaving the material - thus constantly changing between climb milling and conventional milling.

Connection Radius - You can connect lines of the linear tool path with a radius. Radius value is 0, SolidCAM connects the linear tool path with straight lines.

If the

Connection with radius

Forward

Connection without radius

The tool nishes one line of the linear pattern. At the end of the line, the tool rapids (G0) to the safety distance and then to the start of the next cut line. The tool will always use climb or conventional milling.

353

SolidCAM2005 Milling Users Guide

7. 3D Milling

Upward

The tool will always cut from the lowest point of the tool path line to the highest point. From the highest point of the cut, the tool will move rapidly to the start point of the next

cut.
Downward

The tool will always cut from the highest point of the tool path line to the lowest point. From the lowest point of the cut, the tool will then move rapidly to the start point of the next cut.

354

7. 3D Milling

SolidCAM2005 Milling Users Guide

Define Direction
By Angle

Enter the angle that denes the orientation of the tool path. A value of 0 will generate the tool path lines in the direction of the positive X-axis.
By Line

When you choose the Line option, the Define button will be activated and you can dene a line that determines the orientation of the tool path. The direction vector is dened by picking two points that dene the start point and end point of the direction line. The angle of the selected line will be output to the angle eld. Technology
Side Step (constant)

In linear nishing, SolidCAM generates a line pattern on a 2D plane above the model and then projects it on the 3D model. The side step value determines the constant distance between all lines of the linear pattern created on the 2D plane before it is projected.
Scallop

This option enables you to control the distance between the tool path lines by the cusp height you want to achieve on the nished model. SolidCAM will adjust the distance between the single lines of the 2D pattern (before projection on the model) to the topology of the model to match the specied scallop height.
Maximum side step

On at areas, the bull nose cutter could achieve a small scallop with a rather large side step. You can use this value if you want to limit the chip load on the tool or the cutting forces that a large side step could cause.
Arc approximation

You can create G2/G3 G-Code output from Linear nish operations. SolidCAM checks whether successive points of the calculated tool path can be connected using an arc or circle. If an arc or circle connection within the specied arc approximation tolerance can be made, you will receive arc and circle interpolation commands G2 and G3 in the generated G-Code. This feature can drastically reduce the number of lines in G-Code les. Most CNC-controllers and machines work much faster on arcs and circles than on single tool path points or splines. Arc approximation will increase actual feed rates on older CNC-machines and the machine will work smoother. The Tolerance value denes the tolerance SolidCAM uses to position tool path points on arcs or circles.

355

SolidCAM2005 Milling Users Guide

7. 3D Milling

Cross finish
Cross finish type None

Linear machining will be performed only in the direction you have specied and no cross nish is executed.
Normal

After nishing the model in the rst specied direction, another linear nish is performed at an angle of 90 to the rst cutting direction. The Normal cross nish option will remachine the complete area that has been machined in the rst cut linear operation
Linear finish tool path

Normal cross finish tool path

356

7. 3D Milling

SolidCAM2005 Milling Users Guide

Smart

The Smart cross nish option will only re-machine areas that have not been nished within the given scallop during the rst linear nish operation at an angle of 90 to the rst cut. The values set in the Maximum side step and the Minimum side step affect the calculation. If the scallop can be achieved using side steps larger than the minimum side step, no cross nish is necessary - some other constellation could result in all the working area to be re-machined.
Linear finish tool path

Smart cross finish tool path

Minimum side step

This value can be used to avoid tool paths that are too narrow. You can, for example, enter a scallop of 0.02. For some areas SolidCAM would calculate a distance between two lines with 0.01 or less (at very steep walls). To reduce machining time and to avoid long G-Code les, you could then limit the minimum side step of the tool to 0.05.

357

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.5.5 Offset cutting Finish Strategy Offset cutting is a form of 3D prole milling that can be used to mill specic areas of the model. This strategy offers two possible alternatives of prole selection: If you select one Prole, you must specify the clear offset distance. On the right side of the prole, relative to the chain direction, the machining will be performed until the specied clear offset distance has been reached. In this example, the Offset Profile has been machined normal to the prole geometry.
Offset Geometry

Tool path

When you dene two Offset Profiles, both prole geometries are connected and the tool path is projected on the 3D model.

Offset Geometry

Tool path

The Offset Finish dialog displays parameters of the Offset Finish.

358

7. 3D Milling

SolidCAM2005 Milling Users Guide

Offset geometry In this section, specify which prole geometry you want to use for the offset nish. Cutting area
Clear offset

This value determines the offset distance from the prole that will be machined in the right direction of the geometry. This eld is active if you use an offset geometry that consists of only 1 prole. In case the geometry has 2 proles, this eld will be inactive, as the proles will be automatically connected.
Side Step

In offset nish, SolidCAM generates the offset pattern on a 2D plane above the model and then projects it on the 3D model. The side step value determines the constant distance between all lines of the offset pattern created on the 2D plane before it will be projected.
Equal distance

By tagging Equal distance you can keep an equal distance between the tool paths.
Extend to edge

If this option is inactive, the tool path will be generated up to the position where the tool center is aligned with the end-point of the face; this could leave an unmachined area. When this option is active, the tool path is extended till the tool is tangent to the face, at the end-point of the face.

Unmachined area

The Extend to Edges option is turned off

The Extend to Edges option is turned on

This option is available only if the Equal Distance option is activated.

359

SolidCAM2005 Milling Users Guide

7. 3D Milling

Tool side

This option enables you to dene the working side of the geometry.

Geometry orientation

Left side machining

Right side machining

360

7. 3D Milling

SolidCAM2005 Milling Users Guide

Cutting direction
Cross Finish

Check this eld if you want to perform a Cross finish on the offset area. After nishing the model in the rst specied direction, i.e. parallel or normal to the prole geometry, the other possible option will also be applied.

First cutting direction

If you have checked the cross nish eld, both cutting directions will be applied to the offset area. Select which you want to use rst. When no cross nish is used, only the selected option will be performed.
Parallel to geometry

SolidCAM will generate a pattern with offset lines parallel to the offset prole geometry. This pattern will then be projected on the model.
Normal to geometry

SolidCAM will generate a pattern with offset lines normal (90 degrees) to the offset prole geometry. This pattern will then be projected on the model.

361

SolidCAM2005 Milling Users Guide

7. 3D Milling

Tool path connections

Direction type For&Back

The tool nishes one line of the offset pattern and then moves directly to the next line and so on. It mills forward and backward without leaving the material - thus constantly changing between climb milling and conventional milling.
Forward

The tool moves nishes one line of the linear pattern. At the end of the line, the tool rapids (G0) to the safety distance and then to the start of the next cut line. The tool will always use climb or conventional milling.
Connection type

This option enables you to control the way the tool moves between two adjacent tool paths.
Stairs

When the Stairs option is activated, the tool will move in two steps between two adjacent tool paths. If the next path is lower than the present path, the tool rst moves away from the surface in the XY direction and then moves downwards in Z. In case the next path is higher than the present path, the tool will rst move upwards in Z and then approach the surface in the XY direction.

Smooth

Between two adjacent tool paths, the tool moves on the surface of the model. The line connecting the two adjacent tool paths is projected on the model. When you use the Smooth option, the tool will not leave the material when moving to the start point of the next tool path.

362

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.5.6 Spiral Finish Strategy Five different types of spiral tool path movements can be selected for this nishing strategy. The spiral tool path pattern is rst generated in 2D and is then projected on the 3D model. During this projection, the Z-position of the tool is calculated so as to prevent gouging of the model. The Spiral Finish dialog displays parameters of the Spiral Finish.

Tool path type By combining the options in the Path type and Profile type elds, you can generate 5 different kinds of tool path spirals. For each of the combinations you can set additional parameters in the Angle and Radius sections that will affect the spiral.

363

SolidCAM2005 Milling Users Guide

7. 3D Milling

Path type: Linear

Additional parameters: Start Angle End Angle Delta Angle

364

7. 3D Milling

SolidCAM2005 Milling Users Guide

Path type: Spiral

Profile type: Arcs

Additional parameters: Start Angle End Angle Start Radius End Radius Delta Radius

365

SolidCAM2005 Milling Users Guide

7. 3D Milling

Profile type: Lines

Additional parameters: Start Radius End Radius Delta Radius Path type: Circular

366

7. 3D Milling

SolidCAM2005 Milling Users Guide

Profile type: Arcs

Additional parameters: Start Angle End Angle Start Radius End Radius Delta Radius Profile type: Lines

Additional parameters: Start Radius End Radius Delta Radius

367

SolidCAM2005 Milling Users Guide

7. 3D Milling

Cutting direction The spiral will be machined in either clockwise (CW) or counterclockwise (CCW) direction. The direction also affects the angle area that will be machined. Machining always starts at the angle given in Start angle up to the End angle in the cutting direction. Angle You can limit the angle area that will be machined by setting values for the Start and End angle. The direction of the positive X-axis is entered with a value of 0 degrees. Machining will always start from the given start angle and will move in the cutting direction towards the end angle. The Delta angle is used to specify the angle steps of the tool path spiral in the Path type: Linear option. Radius You can set values for the Start and End radius of the tool path spiral. The Delta radius species the offset distance to the next circle or spiral circumference of the tool path spiral. Pick center of tool path spiral This button enables you to dene the center of the tool path spiral that will be projected on the model. If you do not choose any center, the system uses the current Home position as the center of the spiral. Enter the X,Y,Z coordinates of the center point into the Edit bar and conrm by clicking on Enter or dene a point by pick. Tool path connections
Direction type For&Back

The tool nishes one line of the spiral pattern and then moves directly to the next tool path line and so on. It mills forward and backward without leaving the material - thus constantly changing between climb milling and conventional milling.

368

7. 3D Milling

SolidCAM2005 Milling Users Guide

Forward

The tool moves nishes one line of the linear pattern. At the end of the line, the tool rapids (G0) to the safety distance and then to the start of the next cut line. The tool will always use climb or conventional milling.

Connection type

This option enables you to control the way the tool moves between two adjacent tool paths.
Stairs

When the Stairs option is activated, the tool moves in two steps between two adjacent tool paths. If the next path is lower than the present path, the tool rst moves away from the surface in the XY direction and then moves downwards in Z. In case the next path is higher than the present path, the tool will rst move upwards in Z and it will then approach the surface in the XY direction.

Smooth

Between two adjacent tool paths, the tool moves on the surface of the model. The line connecting the two adjacent tool paths is projected on the model. When you use the Smooth option, the tool will not leave the material when moving to the start point of the next tool path.

369

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.5.7 Circular Pocket Finish Strategy This strategy uses the selected Working area to create a 2D pocket line pattern on a plane above the model. The line pattern is then projected on the 3D model. During this projection, the Z-position of the tool is calculated to avoid gouging of the material.

The shape of the Working area and the values for the Tool position in the Working area dialog of this job will directly affect the tool path. The Circular Pocket Finish dialog displays the parameters of the Circular Pocket Finish strategy..

Cutting direction The pocket will be machined in either clockwise (CW) or counterclockwise (CCW) direction. Start from The machining can be started from Outside or Inside the pocket.

370

7. 3D Milling

SolidCAM2005 Milling Users Guide

The combination of both elds, Cutting direction and Start from, will result in climb or conventional milling. Select CCW/Outside or CW/Inside to perform climb milling - any other combination will result in conventional milling of the model. Connection type This option enables you to control the way the tool moves between two adjacent tool paths.
Stairs

When the Stairs option is activated, the tool will move in two steps between two adjacent tool paths. If the next path is lower than the present path, the tool rst moves away from the surface in the XY direction and then moves downwards in Z. In case the next path is higher than the present path, the tool will rst move upwards in Z and it will then approach the surface in the XY direction.

Smooth

Between two adjacent tool paths, the tool moves on the surface of the model. The line connecting the two adjacent tool paths is projected on the model. When you use the Smooth option, the tool will not leave the material when moving to the start point of the next tool path.

Side Step In pocket nishing, SolidCAM generates the pocket line pattern on a 2D plane above the model and then projects it on the 3D model. The side step value determines the constant distance between the lines of the pocket created on the 2D plane before it will be projected on the model.

371

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.5.8 Constant-Z Finish Strategy This strategy produces very high quality nish especially on steep surfaces and minimizes full 3 axis movements that slow down older machines and controllers. The scallop option adjusts the necessary Z-down steps to the surface ow and results in shorter machining times.

The Constant-Z Finish dialog displays the parameters of the Constant Z Finish.

372

7. 3D Milling

SolidCAM2005 Milling Users Guide

Constant-Z wall machining

Activate the checkbox to machine all areas of the model that are not parallel to the XY-plane, i.e. are not planar. The Z-down step can be controlled by two different options:
Down step options

SolidCAM enables you to choose one of two options for Constant-Z wall machining:
Constant down step

Starting from the Job Upper level, SolidCAM will use the specied down step to calculate each successive Z-level. A value of 20 for the Job Upper plane and a constant down step of 1.5 will produce a tool path on the model contour at Z 20, Z18.5, Z17, Z 15.5, ... etc. until the Job Lower plane has been reached.
Variable down step

SolidCAM will automatically calculate the necessary down steps to produce the specied scallop (cusp height) on the model surface. On steep areas, the down step will naturally be larger than on more level areas.
373

SolidCAM2005 Milling Users Guide

7. 3D Milling

Scallop

The Scallop value determines the cusp height of the resulting surface nish. The smaller the value, the smoother the surface nish will be.

Scallop

Maximum down step

On vertical walls of the model, SolidCAM could apply large down steps as this would theoretically result in 0 scallop. To avoid large cutting depth and tool load, you can limit the maximum step between two successive Z-levels.
Minimum down step

On nearly level areas, the necessary down step to achieve the specied scallop could be very small. You can set a minimum down step value that will override the smaller down step generated by the scallop calculation.
Start Machining (Define start by angle) Angle

Enter the angle that denes the start position of the tool path. A value of 0 will generate the tool path start point on the intersection of the contour and the positive X-axis.
Line

When you choose the Line option, the Define button will be activated and you can dene a line that determines the orientation of the tool path. The direction vector is dened by picking two points that dene the start point and end point of the direction line. The angle of the selected line will be output to the angle eld.

374

7. 3D Milling

SolidCAM2005 Milling Users Guide

Arc approximation

This command enables you to create G2/G3 G-Code output from Constant Z operations. SolidCAM checks whether successive points of the calculated tool path can be connected using an arc or circle. If an arc or circle connection within the specied arc approximation tolerance can be made, you will receive arc and circle interpolation commands G2 and G3 in the generated G-Code. This feature can drastically reduce the number of lines in G-Code les. Most CNCcontrollers and machines work much faster on arcs and circles than on single tool path points or splines. Arc approximation will increase actual feed rates on older CNC-machines and the machine will work smoother. The Tolerance value denes the tolerance SolidCAM uses to position tool path points on arcs or circles. The arc approximation value should be smaller than the specied value for the surface offset. A warning message will be displayed if a larger value could cause gouging of the model.
Approach/Retreat

You can control the way the tool approaches and retreats from the prole. Select an option from the list eld and enter the Distance value for this option. SolidCAM enables you the following optionsfor the Approach/Retreat:
None Normal Arc Tangent

For more information on the Approach/Retreat option, please refer to the topic 6.1.2.
Compensation

This option enables SolidCAM to use the tool radius compensation options G4x of the CNC controller in G-Code output.

375

SolidCAM2005 Milling Users Guide

7. 3D Milling

Clean contours of flat areas

In prismatic solid parts, if there is a ledge at a depth that falls between down-steps or a wall at the edge of a at bottom of Constant-Z machining, SolidCAM can still recognize this ledge or wall and machine it as if in a prole job (between the machining of the previous and next Z-steps).
Connection type

This option enables you to control the way the tool moves between two adjacent tool paths.
Stairs

With the Stairs tool path connection, the tool will move in two steps between two adjacent tool paths. If the next path is lower than the present path, the tool rst moves away from the surface in the XY direction and then moves downwards in Z. In case the next path is higher than the present path, the tool will rst move upwards in Z and then it will approach the surface in the XY direction.
Tangential

Between two adjacent tool paths, the tool moves away from the contour in a tangent movement. It continues in a 3D arc/spiral movement to the next Z-level and then approaches the contour in another tangent movement. The Tangential tool path connection smooths lead in/out moves and is especially useful for High Speed Machining. It will avoid Witness marks on the model that could be caused from a Z approach movement on the models surface. The Approach radius denes the radius of the 3D arc that is used to create the tangential move between two successive Z-levels. The value is the maximum radius used as SolidCAM will automatically reduce the radius if the model topology will not leave enough space to approach with the specied radius. This could happen in narrow cavities of the model when a large tool is being used.

376

7. 3D Milling

SolidCAM2005 Milling Users Guide

Cutting direction (Cut from:) Top to bottom

The machining will start on the Job Upper plane and continue downward in the -Z direction until the Job Lower plane is reached. The tool nishes one line of the linear pattern, moves directly to the next line and so on. It mills forward and backward without leaving the material - thus constantly changing between climb milling and conventional milling.
Bottom to top

The tool will start from the Job Lower plane and machine towards the Job Upper plane.
Milling type Climb milling

contour strategy

The tool cuts on the left side of the model contour. Unless the selected Open is set to For&Back, contours will always machine in the climb milling direction.

Conventional

The tool will cut on the right side of the model contour. On outside contours, this will generate a tool path in clockwise direction.
Open contour strategy

This eld controls the milling direction on contours that cannot be closed because the model or a specied working area does not enable SolidCAM to continue the tool path in a closed loop.
Forward

The tool will retreat to the clearance plane and move to the start point of the next tool path, always keeping the cutting direction specied in the Milling type.
For&Back

This option enables the tool to change the cutting direction when it encounters open contours on the model. The milling direction on open contours will change between climb and conventional milling until the open contour has been nished. With the For&Back option, rapid moves from Z-Level to Z-level will be greatly reduced.

377

SolidCAM2005 Milling Users Guide

7. 3D Milling

Fillet size for last cut

This option enables you to add a radius to sharp corners of the tool path without having to change the geometry. For more information on this option, please refer to the topic 6.1.4.

378

7. 3D Milling

SolidCAM2005 Milling Users Guide

Constant-Z flat floor machining

Use the checkbox to activate this option. SolidCAM recognizes planar areas on 3D models. For at, planar areas of the model, working areas will be automatically created that can be machined using a hatch or contour style pocket.
Flat floor machining greatly reduces programming time of 3D models with 2.5D features like pockets and proles on different Z-levels.

379

SolidCAM2005 Milling Users Guide

7. 3D Milling

Scallop

Enter the scallop (cusp height) of the nished surface you want to achieve. SolidCAM will automatically calculate the side step of the tool.
Maximum side step

If you use a at tool or a bull nose cutter, the side step will be as large as the at area of the tool, e.g. for a tool diameter 6 with a corner radius of 1, the side step on at areas would be 4. To limit the cutting width of the tool, enter the maximum side step value.
Machining style

SolidCAM enables you to choose two styles of the oor machining during Constant-Z nishing:
Contour style

Select this option if you want to machine the at oor areas on your model as a contour style pocket. The pocket tool path will travel at parallel offsets to the outside contour of the at area. 1. Choose the Contour strategy with the radio button. 2. Click on the Data button to dene the Contour parameters. For more information on the Contour machining, please refer to the topic 6.2.5.
Hatch style

The tool mills the at area in a linear pattern. 1. Choose the Hatch strategy with the radio button. 2. Click on the Data button to dene the Hatch parameters. For more information on the Hatch machining, please refer to the topic 6.2.4. Withthe Mode button SolidCAM enables you to locate open pocket areas and enables you to machine them with a specic strategy. This strategy enables you to combine pocket and prole tool paths in order to provide the best productivity in open pocket machining.. For more information on the Open Pocket machining, please refer to the topic 6.2.5.

380

7. 3D Milling

SolidCAM2005 Milling Users Guide

Arc approximation

This command enables you to create G2/G3 G-Code output from Constant Z operations. SolidCAM checks whether successive points of the calculated tool path can be connected using an arc or circle. If an arc or circle connection within the specied arc approximation tolerance can be made, you will receive arc and circle interpolation commands G2 and G3 in the generated G-Code. This feature can drastically reduce the number of lines in G-Code les. Most CNCcontrollers and machines work much faster on arcs and circles than on single tool path points or splines. Arc approximation will increase actual feed rates on older CNC-machines and the machine will work smoother. The Tolerance value denes the tolerance SolidCAM uses to position tool path points on arcs or circles.
Fillet size for last cut

This option enables you to add a radius to sharp corners of the tool path without having to change the geometry. For more information on this option, please refer to the topic 6.1.4.

381

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.5.9 Pencil milling

Pencil milling

moves the cutter along internal corners, removing machining cusps left by previous machining operations. By allowing the tool to move in all 3 axes simultaneously, it is possible to pencil mill complex 3D proles. The Pencil milling dialog enables you to dene the parameters of the Pencil milling.

382

7. 3D Milling

SolidCAM2005 Milling Users Guide

Threshold angle The threshold angle is the minimum angle value of the internal corner. SolidCAM will machine corners from the threshold angle parameter or any angle greater than this value. For each corner SolidCAM calculates the center line to machine the angle area optimally.

Offset SolidCAM enables you to machine the area dened by the threshold angle with the constant offset from both sides of the center line.
Side step

Tool path Center line

Denes the side step of both sides of the original center line of the Pencil milling.
Number of side steps

This option enables you to determine the number of side steps. Start from:
Inside

This allows you to start the side steps from the tool path outwards.
Outside

This allows you to start from outside side step working toward the original tool path.

383

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.6 3D Engraving Job

You can mill text or any other prole on a 3D geometry. The prole will be projected on the surface, engraving the contour at a specied depth.

When you select the commands Add>3D Engraving, the 3D Engraving Job screen will be displayed.

384

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.6.1 Geometry name In this section specify the 3D model, i.e. the solids and surfaces on which you want to engrave proles or text. For more information on 3D Model Geometry , please refer to the topic 4.4 7.6.2 Engraving depth This parameter species the depth the tool will penetrate the surface of the 3D model. 7.6.3 Tolerance

The tolerance settings will affect the surface quality of the engraving operation. For more information on Tolerances, please refer to the topic 7.3

385

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.6.4 Engraving geometry name In this section you have to specify the contour, i.e. prole geometry that you want to engrave on the 3D model surface. For more information on Profile Geometry, please refer to the topic 4.5 7.6.5 Engraving technology

Type This option enables you to semi-nish and/or nish the engraved prole on the translated surface. Semi-finish will prepare the engraving prole to an offset specied in the Offset eld with cutting depths given in the Down step eld. Finish will machine the engraving prole to its nal dimensions in one down step. Both. Use this option to machine the limit rst with a semi-nish cut and then with a nishing cut.

386

7. 3D Milling

SolidCAM2005 Milling Users Guide

Side The tool can cut on the left to the prole, right to the prole or on the engraving geometry. Right. The tool will cut on the right side of the prole geometry up to a distance dened by the Offset value. Left. The tool will cut on the left side of the prole geometry at a distance dened by the Offset value. Middle. The center of the tool will move on the prole geometry. Offset You can specify the offset from the engraving geometry for a Semi nish operation on the left or right side of the geometry. This offset will be removed by the Finish cut, if you had dened one. Down step This value denes the successive Z-cutting depth during the Semi-nish operation of the engraving prole.
From Job Upper level

With this option SolidCAM does Roughing passes, at each down step, from the Job Upper Level to the virtual surface located at an offset from the actual surface. This offset is dened with the Engraving depth.
Job Upper Level

Actual surface

Surface with offset defined with Engraving depth

387

SolidCAM2005 Milling Users Guide

7. 3D Milling

From surface

In this case SolidCAM executes roughing passes, at each down-step, only from an actual surface to a virtual surface dened with engraving depth.
Geometry Actual surface

Surface with offset dened with Engraving depth

388

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.7 3D Drill Job

This job enables you to perform drills and other canned drill cycles. In contrast to Drill Job (see the topic 6.3), 3D Drill Job enables you to take into account the solid model geometry. SolidCAM enables you to use holes, machined by this job, for the descent during 3D model roughing (for more information on the Descent stratees, please refer to the topic 7.4.6). Like Drill Job, 3D Drill Job supports the canned drill cycles provided by your particular CNC Machine such as threading, peck, ream, boring etc...

389

SolidCAM2005 Milling Users Guide

7. 3D Milling

When you select the commands Add>3D Drill, the 3D Drill Job screen will be displayed.

7.7.1 Geometry name In this section, specify the drill positions, i.e. the drill geometry you want to use. 7.7.2 Tool In addition to the standard tool options described in the Tool area section, SolidCAM enables you to label a tool as a center drill. This option is used for automatic sorting. In automatic sorting, tools that are labeled as center drills can be automatically moved to the top of the job list. 7.7.3 3D Model Geometry name SolidCAM enables you to dene the 3D model geometry. The 3D model geometry is used for the drilling depth denition.

390

7. 3D Milling

SolidCAM2005 Milling Users Guide

7.7.4 Offset from model SolidCAM enables you to dene the depth of the 3D drilling by the Offset from model value. The Offset from model value can be either positive or negative. With the negative value SolidCAM enables the tool to go deeper into the solid model.

Rest Material Offset from model

Solid Model

7.7.5 Drill cycle type Click on the Drill cycle type button. The Drill canned cycles supported by the post-processor of the current CNC-controller will be displayed. Click on one of the icons to select the canned cycle you want to use in this job. For more information on the Drill cycles, please refer to the topic 6.3.4.

391

SolidCAM2005 Milling Users Guide

7. 3D Milling

7.7.6 Sequence of drill positions You can select one of 3 available options to control the sequence of the drill positions.
Default

The drills will be performed according to the order in which the drill points were picked during the geometry denition.
Line

You have to dene a direction by selecting two points on your model.

Distance

This option minimizes the length of the necessary tool movement. For more information on the Drill sequence, please refer to the topic 6.3.5.

392

Simulation
You can use the simulation to check and view the generated tool path after you have defined and calculated your machining operations. If you made mistakes in defining the jobs or used unsuitable milling strategies, the simulation can help you avoid problems you would otherwise experience during the actual production run.

HostCAD Simulation mode 2D Simulation mode 3D Simulation mode VerifyPlus Simulation mode SolidVerify Simulation mode Rest Material Simulation mode

SolidCAM2005 Milling Users Guide

8. Simulation

8.1 Introduction
The SolidCAM simulation option enables you to check and view the generated tool path after you have dened and calculated your machining operations. The simulation can help you avoid problems such as mistakes in dening the jobs or selection of an unsuitable milling strategy you would otherwise experience during the actual production run. To simulate a Job, move the mouse on the Job and press the right mouse button in the CAM Manager. The Job menu will be displayed. Click on the Simulate option. 1. You also can simulate a group of selected Jobs. After you select the Jobs with the Control -key, right click on them and choose the Simulation option from the menu. 2. To simulate all the Jobs, right click on the Jobs eld in the SolidCAM Manager and choose the Simulation option from the menu.

The Simulation dialog box will be displayed.

394

8. Simulation

SolidCAM2005 Milling Users Guide

8.1.1 Simulation modes SolidCAM offers various simulation modes:

SolidCAM Simulation modes

2D Simulation

VerifyPlus

HostCAD

3D Simulation

Rest Material

SolidVerify

8.1.2 Simulation Controls The Simulation controls are used to play, pause and exit the simulation.

Click on the control buttons to run and stop the simulation: it on the screen. The image will be shown when the simulation is completed or when the Pause button is pressed. Plays the simulation in continuous mode.
Pauses Turbo mode. SolidCAM makes the simulation in the computers memory without showing

the simulation when in continuous play mode.

Single Step mode (simulate the next tool movement by clicking on the symbol or by using the space bar of your keyboard). Job step mode. Simulation is shown separately Job by Job. Exits

from the simulation module.

395

SolidCAM2005 Milling Users Guide

8. Simulation

8.2 2D simulation mode

This simulation mode enables you to display the tool path in the projection view. This feature is useful in prismatic parts machining.

8.2.1 Simulation Control

8.2.2 Simulation toolbar

The above icons in the toolbar enable you to zoom and pan the simulation picture.

396

8. Simulation

SolidCAM2005 Milling Users Guide

8.2.3 Show Data The check box below gives you complete information about the tool path such as coordinates of the current point, time, feed etc...

The X, Y, and Z elds display the position of the tool relative to the home position at every step of the simulation. Feed displays the current feed rate. Time shows the elapsed machining time of the simulated jobs (theoretical value based on feed and distance covered). 8.2.4 Projection This option enables you to display the simulation on a Top view projection of the CAD model. When you choose this option, the following menu will be displayed:

Define This option enables you to dene entities of the CAD model that are taken into account in the Top view projection. When you choose this option, the following screen will be displayed:

397

SolidCAM2005 Milling Users Guide

8. Simulation

Select edges
Select Unselect

This option enables you to select the edges of the CAD model either by Box, Pick or All edges. This option enables you to unselect edges that were previously selected.

Selection Filter

This option enables you to select edges on a specic Z-level. When you choose this option you can either pick the Z-level with the cursor on the model or you can enter the Z-level in the dialog box. Once you specify the Z-level, only those edges on that level will be picked.
Select edges by
Box Pick All edges

This option enables you to select/unselect edges by enclosing them with a box. This option enables you to select/unselect the edges one by one. This option automatically selects/unselects all the edges.

Finish

This option enables you to build the chain after you pick the edges.
Cancel

This option enables you to exit this dialog box. Delete This option enables you to delete what you had previously dened.

398

8. Simulation

SolidCAM2005 Milling Users Guide

Show on model This option enables you to see the geometry that was selected in the CAD model. Show This option enables you to see the model in the simulation screen. 8.2.5 Show tool
Show tool toggles

on/off a graphic simulation of the tool.

The Parameter eld describes with what frequency SolidCAM must show the tool position. 8.2.6 Erase on Z change Automatically clears the image after every Z change of the tool. 8.2.7 Stop on Next This option displays the Stop on Next dialog where you can dene the specic point to stop the simulation process.

Tool change - This option stops the simulation every time when the tool changes. Feed change - This option stops the simulation every time when the feed changes. Z change - This option stops the simulation at every change of the Z coordinate of the tool. Tool Steps - Stops the simulation every dened number of tool steps. End of procedure - Stops the simulation at the end of the procedure.

399

SolidCAM2005 Milling Users Guide

8. Simulation

8.2.8 Clear This button clears the simulated tool path and the tool images from the screen. 8.2.9 Colors Click on the Colors button to change the display color of the simulated tool path. The Simulation Colors dialog will be displayed.

1. To change the tool color, click on the colored box left to the tool number. 2. The standard color dialog of Windows will be displayed. 3. Select the new tool path color for this tool number. 4. Conrm with OK. You can use the Reset to Default button to apply the default tool colors, as dened in the CAM settings dialog. 8.2.10 Simulation speed

The slider controls the Simulation speed.

400

8. Simulation

SolidCAM2005 Milling Users Guide

8.3 VerifyPlus simulation mode

This simulation mode provides you with additional verication capabilities: 4/5 axes multi-sided solid simulation. Simultaneous 4-axes solid simulation. 2-D turning solid simulation. Turning with mill driven-tools solid simulation.

8.3.1 Simulation toolbar

The toolbar enables you to control the simulation in this mode.

401

SolidCAM2005 Milling Users Guide

8. Simulation

Setup and Simulation modes

VerifyPlus

has two working modes:

for Setup and

for Simulation.

Setup mode

In this mode VerifyPlus enables you to specify the scale and orientation of the model.
Simulation mode

After setup, switch to the simulation mode. VerifyPlus shades the prepared block and prepares it for simulation.

In the Simulation mode, machining can be simulated with standard SolidCAM simulation controls. In this mode all controls for setup of the simulation (scale and orientation) are disabled. You can turn on/off the visualization of tool and also specify the tool visualization as either wireframe or shaded. You can also rotate the display and dene the light controls.

402

8. Simulation

SolidCAM2005 Milling Users Guide

8.3.2 Buttons available in the Setup Mode

Fit to window

Fits the CAM-Part to the entire screen.

Fit by box

The area you want to view in the simulation screen is dened by box.
Move

Moves the CAM-Part to any point on the screen.

Rotate

Rotates the model.

Zoom

Zooms in/out the image on the screen.

Machine orientation

This button enables you to ip the CAM-Part back and forth by 90 degrees. This option is needed to do realistic simulation on vertical/ horizontal machines.

Vertical machine simulation Isometric views buttons

Horizontal machine simulation

These buttons enable you to view the CAM-Part in the left, right, back or front isometric views.
View buttons

These buttons enable you to view the CAM-Part in the top, left, back, bottom, right or front views.
Show/Hide Tool button

Pressing this button enables you to show or hide the tool during simulation. This option is also available in the simulation mode.

403

SolidCAM2005 Milling Users Guide

8. Simulation

Wire Tool/Shaded Tool

These buttons enable you to see the tool as a wire frame tool or as a solid tool.

Shaded tool simulation

Wireframe tool simulation

The wireframe tool will always be seen in it entirety, whereas the solid tool is partially hidden by the CAM-Part.
Show/Hide Tool Holder.

This button is active in turning only. When pressed, it allows you to see the holder of the turning tool.
Section View

This button is active in Turning only. When pressed, it allows you to see the whole CAM-Part or with a quarter cut away.

Section view mode

Normal mode

404

8. Simulation

SolidCAM2005 Milling Users Guide

8.3.3 Buttons available in the Simulation Mode

Flip

This button ips the CAM-Part back and forth. We need it in the simulation mode to see other sides of the CAM-Part during the simulation. This option is useful for multi-sided simulation.
Solid Rotate

This button enables you to rotate the CAM-Part to any position after simulation without exiting to Setup mode. To rotate the solid, click on any location inside the Graphics view using the left button of the mouse, hold the button down and drag the cursor across the screen. A small inset window at the center of the view will display a continuous snapshot of the current orientation of the model. When you release the button, the entire view is updated to show the new orientation of the model. The effect of the change in rotation is not permanent, and this change has to be reset to proceed with the Simulation.

405

SolidCAM2005 Milling Users Guide

8. Simulation

Light control

This command enables you to use the left button of the mouse to change the light source on the solid model in the Simulation mode. To change the light source, click on any location inside the Graphics view using the left button of the mouse, hold the button down and drag the cursor around within the bounds of the view. A small inset window at the center of the view will display a snapshot of the current lighting effect on the model. When you release the button, the entire view is updated to show the light change effect on the complete model. The Move light source command is used for visual purposes only. The effect of the change in light source direction is not permanent. The light source change has to be reset before proceeding with the Simulation.

8.4 Host CAD simulation mode

This simulation mode enables you to display the tool path directly on the model in the Host CAD window. Since all the View options of the Host CAD are active during the simulation, you can see the tool path from different perspectives and zoom in on a certain area of the model. 8.4.1 Simulation Control

406

8. Simulation

SolidCAM2005 Milling Users Guide

8.4.2 Show Data This check box gives you information about the tool path such as coordinates of the current point, time, feed etc... For more information on the Show Data option, please refer to the topic 8.2.3. 8.4.3 Show Tool Show tool toggles on/off a graphic simulation of the tool. The Parameter eld describes with what frequency SolidCAM must show the tool position. 8.4.4 Stop on Next This option opens the Stop on Next dialog where you can dene the specic point to stop the simulation process. For more information on the Stop on Next option, please refer to the topic 8.2.7. 8.4.5 Clear This button clears the simulated tool path and the tool images from the Host CAD screen. 8.4.6 Colors Click on the Colors button to change the display color of the simulated tool path. The Simulation Colors dialog will be displayed. For more information on the Colors option, please refer to the topic 8.2.9. 8.4.7 Simulation speed You can use the slider to control the Simulation speed.

407

SolidCAM2005 Milling Users Guide

8. Simulation

8.5 3D simulation mode

This simulation mode enables you to display the tool path on the 3D model using all the graphic acceleration functionality of OpenGL. The target model must be dened to use this simulation mode. For more information on the Target model, please refer to the topic 2.4.

8.5.1 Simulation toolbar SolidCAM enables you to use the toolbar to control the simulation in this mode.

The following icons are available in this toolbar: These icons are used for model scaling, panning and rotating. This icon enables you to remove the simulated tool path from the screen. With these icons you can toggle on/off the tool visualization during the simulation. This icon enables you to switch the graphic screen between three modes: Tool path only simulation Tool path and model simulation Model only simulation These icons enable you to show the model in the projection views (Left, Right, Top etc...)
408

8. Simulation

SolidCAM2005 Milling Users Guide

This icon returns the original position and orientation of the model. These icons switch the simulation to 4/1 view mode. This option enables you to show the Zoom Window with the enlarged image of the model and tool path fragment centered on the mouse position. You can control the zoom factor in the Zoom Window.

These icons enable you to show the dynamic section of the model. The section slider will be displayed in the graphic area. By moving this slider you can control the section.

409

SolidCAM2005 Milling Users Guide

8. Simulation

8.5.2 Simulation control

8.5.3 Show Data This check box gives you information about the tool path such as coordinates of the current point, time, feed etc... For more information on the Show Data option, please refer to the topic 8.2.3. 8.5.4 Stop on Next This option opens the Stop on Next dialog where you can dene the specic point to stop the simulation process. For more information on the Stop on Next option, please refer to the topic 8.2.7. 8.5.5 Colors Click on the Colors button to change the display color of the simulated tool path. The Simulation Colors dialog will be displayed. For more information on the Colors option, please refer to the topic 8.2.9. 8.5.6 Simulation speed. You can use the slider to control the Simulation speed.

410

8. Simulation

SolidCAM2005 Milling Users Guide

8.6 SolidVerify simulation mode

This mode enables machining simulation on the solid model. The solid stock model (dened by material boundaries) is used in this mode. During the machining simulation process, SolidCAM subtracts the tool movements (using solid Boolean operations) from the solid model of the stock. The remaining machined stock is a solid model that can be dynamically zoomed or rotated.

Solid tool Solid stock model

8.6.1 Simulation Control

8.6.2 Show Data This check box offers you complete information about the tool path such as coordinates of the current point, time, feed etc... For more information on the Show Data option, please refer to the topic 8.2.3.

411

SolidCAM2005 Milling Users Guide

8. Simulation

8.6.3 Stop on Next This option opens the Stop on Next dialog where you can dene the specic point to stop the simulation process. For more information on the Stop on Next option, please refer to the topic 8.2.7. 8.6.4 Clear This option enables you to clear the simulation and return to the unmachined stock. 8.6.5 Simulation speed SolidCAM enables you to use the slider to control the Simulation speed. 8.6.6 Single color/Color by tool
Single color

This option enables you to use a single color for all tools during the simulation process.
Color by tool

Use this option to dene a specic color for each tool. Click on the Color by tool button to set the colors. The Simulation Colors dialog will be displayed. 1. To change the tool color, click on the colored box left to the tool number. 2. The standard color dialog of Windows will be displayed. 3. Select the new tool path color for this tool number. 4. Conrm with OK. You can use the Reset to Default button to apply the default tool colors, as dened in the CAM settings dialog.

412

8. Simulation

SolidCAM2005 Milling Users Guide

8.6.7 Simulation toolbar

The toolbar below enables you to control the simulation in this mode.
Available buttons:
Fit to window

Fits the CAM-Part to the entire screen.

Fit by box

The area you want to view in the simulation screen is dened by a box.
Move

Moves the CAM-Part to any point on the screen.

Rotate

Rotates the model.

Zoom

Zooms in/out the image on the screen.

Light control

This command enables you to use the left button of the mouse to change the light source on the solid model in the Simulation mode. To change the light source, click on any location inside the Graphics view using the left button of the mouse, hold the button down and drag the cursor around within the bounds of the view.

413

SolidCAM2005 Milling Users Guide

8. Simulation

Isometric views buttons

These buttons enable you to view the CAM-Part in the left, right, back or front isometric views.
View buttons

These buttons enable you to view the CAM-Part in the top, left, back, bottom, right or front views.
Render mode

Displays a shaded view of the model.

Hybrid mode

Displays a transparent view of the model.

414

8. Simulation

SolidCAM2005 Milling Users Guide

Wire mode

Displays the CAM-Part and tool movements in wireframe mode.

Hidden line mode

Displays the CAM-Part and the tool movements in hidden-line wireframe mode.

415

SolidCAM2005 Milling Users Guide

8. Simulation

Redraw

Redraws the view.

Show/Hide Machined Stock

Shows/hides the machined stock model

Show/Hide Target

Shows/hides the target model.

Show/Hide Rest Material

Shows/hides the rest material on the machined stock model.

Show/Hide Split Solids

This option displays the Show/Hide Split solids dialog.

This dialog enables you to switch between split solids during the simulation and enables you to remove the pieces of material that have been cut away during the machining
Show/Hide Gouges

Shows gouges of the target model.

Split Gouges

This option displays the Show/Hide Split solids dialog. This dialog enables you to switch between split solids of gouge areas during the simulation and enables you to check separately the areas of the gouge

416

8. Simulation

SolidCAM2005 Milling Users Guide

Compare target and machined stock

This option enables you to compare the stock model and target model and assign different colors to different rest material areas, depending on their tolerance.

1. Set the tolerance values and colors in the Target and Stock Compare Options dialog. 2. Press Execute to show the comparison. 3. Press OK to exit.
Activate/Disactivate initialization of machined stock

This option is used in the case of single job simulation. If this option is turned on, SolidCAM enables you to perform the simulation on the stock machined by previous jobs. If this option is turned off, SolidCAM performs the simulation on the original unmachined stock model.
Show/Hide Tool

Shows or hides the tool during simulation.

Show/Hide Holder

Shows or hides the tool holder during simulation.

Show/Hide Fixture

Shows or hides the xture during simulation. For more information on the Fixtures denition, please refer to the topic 5.6.

417

SolidCAM2005 Milling Users Guide

8. Simulation

Save the simulation model

This eld enables you to save the current model of the material removal in STL format. This eld is active only when the Solid Rest material calculation method and Manual method of the Rest material update are chosen. For more information on this subject, please refer to the topic 2.4.
Load the simulation model

This eld enables you to load the previously saved model of the material removal. The simulation will be performed on the loaded model. This eld is active only when the Solid Rest material calculation method and Manual method of the Rest material update are chosen. For more information on this subject, please refer to the topic 2.4.

418

8. Simulation

SolidCAM2005 Milling Users Guide

8.6.8 Simulation menu

File
Open Open machined stock from FCT

This option enables you to load the machined stock model from the SolidCAM FCT le (*.fct).
Open machined stock from STL

This option enables you to load the machined stock model from the Stereolithography le (*.stl).
Save machined stock to STL

This option enables you to save the machined stock model to the Stereolithography le (*.stl).

419

SolidCAM2005 Milling Users Guide

8. Simulation

Options
Compare target and machined stock

This option explained above enables you to compare the stock model and target model and assign different colors to different rest material areas, depending on their tolerance. This option displays the Measurements dialog where you can see the dimensions and the volume of the Machined stock model.

Settings
Colors

This option enables you to choose colors for the simulation. The Colors dialog will be displayed.

420

8. Simulation

SolidCAM2005 Milling Users Guide

General

Move tool redraw interval.

This option enables you to expedite the simulation by dening the number of tool movements until the next redraw of the display. The default value is 7.
Tool facet tolerance.

This controls the precision of the tool for the simulation.

Absolute

This parameter denes the precision of the facets of a tool in mm (or inches). Since this is an absolute value, the facets tolerance for the small and large tools will be the same. During the simulation, SolidCAM produces the Boolean subtraction of the tool from the CAM-Part. This tolerance will inuence the quality of the simulation. The quality of the simulation will be the same for large tools and small tools. The speed of the simulation will be relative to the tool. The simulation of the lager tool will be slower.
% of the tool radius

This parameter denes the precision of the facets of a tool in percentages to the tool radius. In this case the facet size will differ from tool to tool. However the amount of facets on the tools will be the same. The quality of the simulation will be relative to the tool. The speed of the simulation will be the same in small tools and large tools.

421

SolidCAM2005 Milling Users Guide

8. Simulation

8.7 Rest Material simulation mode

This simulation mode enables you to display the model with the rest material before and after each Job. It also displays existing gouge areas so that it can be prevented in the real machining. To use this simulation mode, the Target model must be dened and the Update stock model option must be active. For more information about the Target Model and the Update stock model option, please refe to the topic 2.4 This mode will be used only when the Z Buffer mode will be chosen for the Rest Material calculation. When the Solid mode is chosen, the Rest Material simulation will be performed by SolidVerify.

8.7.1 Simulation toolbar

SolidCAM enables you to control the simulation in this mode with the toolbar.
Available buttons:
Model orientation buttons

This set of icons is for model scaling, panning and rotating.

422

8. Simulation

SolidCAM2005 Milling Users Guide

Colors

This button enables you to dene colors for the simulation. The Select Simulation colors dialog will be shown.

Click on the color button to dene the color.

Lighting

This icon enables you to control the lighting of the rest material.
Copy

This icon enables you to copy the simulation image into the Windows clipboard for future use.
Shaded/wireframe mode

These buttons enable you to switch to the shaded/wireframe mode.

Isometric view buttons

These icons enable you to rotate the model into isometric views (Left, Right, etc...)
View buttons

These buttons enable you to view the CAM-Part in the top, left, back, bottom, right or front views..
Refresh

This icon returns the original position and orientation of the model.
Flip

This button switches between the following simulation modes: Model and rest material Rest material only Model only

423

SolidCAM2005 Milling Users Guide

8. Simulation

Dynamic section

These icons enable you to show the dynamic section of the model. The section slider will be displayed in the graphic area. By moving this slider you can control the section.

8.7.2 Simulation control

With the Before Job and After Job options you can display the rest material either before or after the machining within the selected Job or the whole CAM-Part.

424

8. Simulation

SolidCAM2005 Milling Users Guide

8.7.3 Tolerance With this parameter you can control the precision of the rest material simulation. The smaller the tolerance parameter, the better the precision. 1. Set the tolerance value. 2. Click on the update button to redraw the rest material picture according to the new tolerance.

425

SolidCAM2005 Milling Users Guide

8. Simulation

426

G-Code
This command enables you to generate and display the G-Code file for the CAM-Part or for machining jobs. The G-Code file can then be transferred to your CNC-machine using a floppy disk, via a DNC (RS 232) or Ethernet connection. The format of the NC-program depends on the Controller you selected in the CAM-Part data dialog. The G-Code output format can be customized using the GPP interface or by changing the controllers *.mac and *.gpp files.

Generating G-Code

SolidCAM2005 Milling Users Guide

9. G-Code

This command enables you to generate and display the G-Code le for the CAM-Part or for machining jobs. The G-Code le can then be transferred to your CNC-machine using a oppy disk, via a DNC (RS 232) or Ethernet connection. The format of the G-Code depends on the Controller you selected in the CAM-Part data dialog. The G-Code output format can be customized either by using the GPP interface or by changing the controllers *.mac and *.gpp les. Contact technical support for more information on post-processor customization.

9.1 Generate
This option generates all the G-Code les for the CAM-Part after which the le will be displayed using the text editor dened in Settings>Editors. If any changes were made in the job or in the *.mac or the *.gpp post-processor les, you have to generate the G-Code again.
G-Code All

This command is available when you press the right mouse button on the job symbol. You will receive one G-Code le including the necessary tool changes, unless you have separated jobs or job groups using split marks. The G-Code le will be saved to the CAMParts directory and will carry the name: partname.tap.

428

9. G-Code

SolidCAM2005 Milling Users Guide

G-Code for a single job or for a group of jobs

1. Click on the Job you want to generate the G-Code for or select a group of jobs using the mouse in combination with the Shift/Ctrl-key. Then press the right mouse button and choose Generate from the G-Code menu.

2. The G-Code filename dialog prompts you to enter a name for the *.tap le.

9.2 List
This option enables you to display a list of the already generated G-Code les for the current CAMPart or job. The G-Code (*.tap) le will be opened with the text editor dened in Settings>Editors. Use the editor to change, save or print the G-Code le.

429

SolidCAM2005 Milling Users Guide

9. G-Code

9.3 Copy

This option enables you to copy G-Code les. When you choose this option, the list of the generated G-Code les for the current CAM-Part is displayed in the Copy G-Code dialog. 1. Choose the *.tap le you want to copy to another directory (for multiple selections use the Ctrl and Shift-key). 2. Transfer the list of les you want to copy to the middle eld by pressing the Left to Right arrow. 3. Choose the drive and the directory you want to copy to. 4. Press the Copy eld in order to execute the Copy command.

9.4 Print
This option enables you to print the G-Code le.

430

SolidCAM Settings
The SolidCAM Settings feature enables you to define a set of SolidCAM defaults such as SolidCAM folders, units, tolerances, CNC controllers etc... In the settings dialog you can change the path to related applications, units, tolerances, default machines, editors, and color settings for SolidCAM. The Settings register enables you to easily view and edit the current program preferences and options.

10

User Directories Settings Units Settings Simulation Settings Synchronization settings Rest Materal & SolidVerify Settings Tool Settings

SolidCAM2005 Milling Users Guide

10. Settings

10.1 Introduction
In the Settings dialog you can change the path to related applications, units, tolerances, default machines, editors, and color settings for SolidCAM. The Settings register enables you to easily view and edit the current program preferences and options.
DNC Settings Simulation settings Color Setup Auto-save settings External Program settings Synchronization settings Default Geometry Names Rest Materal & SolidVerify Tool Settings User Directories settings Units Settings Default CNC-Controller Editors settings

432

10. Settings

SolidCAM2005 Users Guide

10.2 User Directories Settings

The Path register enables you to set the path to your post-processor les and to your user-directory.

10.2.1 User Directory for SolidCAM-Parts The user directory denes the default folder in which CAM-Parts and G-Code les created with SolidCAM are stored. Whenever you load a CAM-Part, SolidCAM will browse the user directory for SolidCAM-Part les (*.prt). All newly created CAM-Part les will be placed in the user directory by default. 1. Click on the Browse button. 2. The browser window will be loaded. 3. Choose the folder you want from the browser.

433

SolidCAM2005 Milling Users Guide

10. Settings

10.2.2 User Directory for SolidCAM-Tables SolidCAM uses this folder to store Tool Tables and Machining processes. The *.tab le in the SolidCAM Tool Table le contains detailed information about tools. The *.mpt le is the Machining Process Table le. In addition to this le, SolidCAM creates the Machining Process Folder with a set of SolidCAMs auxiliary les. 1. Click on the Browse button. 2. The browser window will be loaded. 3. Choose the folder you want from the browser.

434

10. Settings

SolidCAM2005 Users Guide

10.3 Units Settings

The Units register enables you to set the unit system, spline approximation and chain tolerances.

10.3.1 Metric/Inch This option enables you to select the unit system you want to work with.

435

SolidCAM2005 Milling Users Guide

10. Settings

10.3.2 Approximation Whenever you use a spline edge (NURBS) to select a chain geometry for proles, working areas, sections etc., the spline will be transformed to lines. Approximation on splines denes the tolerance that is used when the spline is transformed to lines. Example: When you import an IGES surface, the surface boundaries will usually be dened with spline curves. If you mill the outside contour of the surface with a prole job, you have to select the boundary as the prole geometry. You will receive straight edges and facets on the contour if you do not adjust the spline approximation to your requirements. If you select a tighter tolerance, the G-Code le will show more points on the contour and produce a smoother edge. This tolerance does not affect jobs that work on 2D contours such as arcs, lines or circles.

10.3.3 Chain selection The Auto select function for selecting chain geometries uses certain tolerances to decide whether two consequent elements are connected or independent. The behavior of this function depends on the Gap between the entities.

Gap

436

10. Settings

SolidCAM2005 Users Guide

Gap minimum and Gap maximum tolerance The Auto select can function in three different ways: If the gap between the edges is less than the minimum chain gap, the system automatically continues the chain and closes the gap. If the gap is between the minimum and maximum values, you are asked whether the gap should be closed. If you answer YES, the gap is automatically closed. If the gap is larger than the maximum value for a chain gap, the message, Chain must be continuous, is displayed. Constant-Z Tolerance When you work in the Auto Constant Z mode, all connected entities on the same Z-level of the current coordinate system will be selected. This tolerance denes the maximum deviation from the Z plane where an element will still be recognized as being on the same Z-level. It mainly depends on the size of your geometries and the accuracy of your models or imported 2D/3D les which gap and constant-Z tolerance you should use. The default setting can be used for most of the common models, but when you work with very intricate CAM-Parts, for example, a large max. gap tolerance can cause problems as you might close contours in places that should normally be not connected. To avoid this, answer No to the message Do you want to close the gap? and switch to single curve mode to make sure you selected the correct elements. 10.3.4 Rest Material Calculation The Target tolerance parameter controls the accuracy of the target and stock model triangulation. 10.3.5 Fillet size for last cut This parameter denes the maximum allowed value of the radius for the external llet. For more information on the Fillet size for last cut option, please refer to the topic 6.1.4.

437

SolidCAM2005 Milling Users Guide

10. Settings

10.4 Default CNC-controller settings

10.4.1 Post-processor files directory GPP les with the extensions *.mac and *.gpp are post-processor les used by SolidCAM. The *.mac le contains information about the CNC-machine, e.g. number of simultaneous axes, available cycles, default tool positioning, etc.. The *.gpp le translates the calculated tool path into G-Code. The G-Code format, cycle denitions, etc. of your G-Code le is controlled through this le. You have to specify the path to the folder where you keep the *.mac and *.gpp les you have received from SolidCAM. The post-processors that come with the evaluation or demo version are installed in the SolidCAM program directory. 1. Click on the Browse button. 2. The browser window will be loaded. 3. Choose the folder you want from the browser.
438

10. Settings

SolidCAM2005 Users Guide

10.4.2 CNC-controllers SolidCAM enables you to dene the default machine controllers:
Milling CNC-Controller Turning CNC-Controller Milling&Turning CNC-Controller WireCut CNC-Controller

The post-processors you selected will be used as the default machine, which means it will appear in the Part Data dialog as the controller for the new CAM-Part. Naturally, you can change the controller for the CAM-Part with the list eld if you want to use another machine controller. 1. Click on the Browse button. A list of milling/turning post-processors available in your Post-processor files directory will be displayed in the Machines list.

2. Double click on the machine you want to use as your default machine.

439

SolidCAM2005 Milling Users Guide

10. Settings

10.5 Color Setup

The Color Setup register enables you to customize the colors used by SolidCAM.

To change a color, click on the corresponding color button. The standard Windows Color selection dialog will be displayed, enabling you to pick the color you want. Customizable display elements: Home: Displays the color of the current Home position. Direction arrow: Displays the color of arrows that indicate the direction of a chain geometry. Point: Displays the color of points during chain selection, e.g. the start point of an element. Numbers: Displays the color of numbers used to identify chain geometries.

440

10. Settings

SolidCAM2005 Users Guide

Section: Displays the color of the section geometries. Clamp: Displays the color of the clamp in SolidCAM-Turning. Show tool: Displays the color of the tool shown from the Job screen. Pick highlight: Selected elements, e.g. surfaces, solids, lines, etc. are highlighted using this color. Show chain/3D model/Drill: Displays the color of geometries when you use the Geometry>Show commands. Chain Accept highlight: Displays the color of chains that have been added to the currently active geometry. General chain selection: Color used to highlight entities suggested as consequent elements of the chain in auto select mode. Limit/Working area: Displays the color of the Limit geometry and Working area geometry. Material boundaries: Displays the color of the Material boundaries. Vertical Type Def. Depth: Displays the color of numbers used to identify the depth of the vertical type variable prole depth. Sloped Type Def. Depth: Displays the color of numbers used to identify the depth of the sloped type variable prole depth. Load default color set This option enables you to load the default colors of SolidCAM. Host CAD background color You can load a pre-dened set of colors for the customizable display elements. These colors have been selected by SolidCAM for the standard background colors of the Host CAD systems used by SolidCAM. Choose the background color of the Host CAD from the list. The Auto adjust option enables you to load the optimal colors for the background of your Host CAD.

441

SolidCAM2005 Milling Users Guide

10. Settings

10.6 Auto-Save settings

SolidCAM enables you to save your CAM-Part automatically after a geometry is dened or edited.

442

10. Settings

SolidCAM2005 Users Guide

10.7 External program settings

SolidCAM enables you to dene a path to an external program (Windows application or batch le) that can be loaded from the SolidCAM menu.

443

SolidCAM2005 Milling Users Guide

10. Settings

10.8 Editors Settings

The Editors register enables you to specify standard editors for text les created by SolidCAM.

Editor for G-Code files (*.tap) Specify the Editor to view, open and print generated G-Code les. Enter the path to a text editor or use Browse to select an application on your system. Editor for CAM-Part Documentation (*.doc) files The documentation for CAM Parts will be generated in text les with the *.doc extension. As the default editor, the SolidCAM viewer.exe can view and print documentation les. You can, however, specify any text editor or word processor that can read *.doc les as the standard editor for your documentation. Enter the path to a text editor or use Browse to select an application on your system. Cover Page This option enables you to dene the path to the Cover Page used for the CAM-Part Documentation.

444

10. Settings

SolidCAM2005 Users Guide

10.9 DNC settings

This option enables you to dene the path for the data transmitting software - the DNC program.

445

SolidCAM2005 Milling Users Guide

10. Settings

10.10 Simulation Settings

The Tool Simulation Color register enables you to customize the color of the tools used during the Turning simulation mode.

For each tool number you can dene a separate color. The colors selected in this dialog will be used for tools of current and future parts. To change a color, click on the color symbol next to the tool number in the list. The standard Windows Color selection dialog will be displayed, enabling you to pick the color you want. Load Default colors Click on the button to load the default SolidCAM color settings for simulation.

446

10. Settings

SolidCAM2005 Users Guide

10.11 Synchronization settings

Check Synchronization always

Ask before synchronization check: Marked

After every change in the part or in the assembly and rebuild, SolidCAM will prompt you before checking the synchronization of the geometries with the model or sketches.
Unmarked

The synchronization checking will be performed without any message or question. Check synchronization on user demand In this case, SolidCAM will not check the synchronization automatically. The Check Synchronization item in the Job and Geometry menus is enabled and you can choose it to start the synchronization.

447

SolidCAM2005 Milling Users Guide

10. Settings

Synchronization tolerance These parameters dene the value of the synchronization tolerance. During the synchronization check, SolidCAM compares the SolidCAM geometry and the SolidWorks model. If the difference between them is out of the specied tolerance (the SolidWorks model was updated); you have to synchronize the geometry with the updated model.
Wireframe Geometry

The value of the tolerance for the Wireframe geometry.

3D Model Geometry

The value of the tolerance for the 3D Model geometry.

448

10. Settings

SolidCAM2005 Users Guide

10.12 Default Geometry Names

SolidCAM enables you to dene and use default names for all geometry types. The Default Geometry Names tab was added to the SolidCAM Settings dialog.

This dialog enables you to dene the Default names for SolidCAM geometries. When a new geometry is dened, the default name will be displayed in the Geometry Name dialog. You can either conrm it or change it. If the default name is already used for a previously dened geometry, SolidCAM offers you the default name with a next sequential number.

449

SolidCAM2005 Milling Users Guide

10. Settings

10.13 Rest Materal & SolidVerify Settings

SolidCAM enables you dene the default settings for Rest Material calculation.

Default Rest Material calculation method This option enables you to set the default method for the Rest material calculation.
Z buffer

In this mode, the rest material is calculated only for one machining direction.
Solid

This mode enables you to calculate the Rest material from all sides. Default Update Stock model method This option enables you to set the default method for the Stock model updating. This option is active only with Solid method of the Rest material calculation.

450

10. Settings

SolidCAM2005 Users Guide

Automatic method

This option causes SolidCAM to automatically calculate and save the rest material after each job. During the SolidVerify simulation of the separate jobs, SolidCAM updates the stock with the previously generated and saved rest material and performs the simulation on the updated model. Since the rest material models are saved after each job calculation, SolidCAM enables you to simulate any job for multi-sided CAM-Parts.
Manual method

SolidCAM enables you to manually save the Rest Material for a specic job during the SolidVerify simulation. The saved model can be used to update the stock. The simulation of the next jobs can be performed on the updated model. STL Save mode This option enables SolidCAM to save the STL le containing the Updated Stock model when the Initialization of machined stock option is active. This option is active either when the Update Rest Material option is not chosen or when the Z-Buffer mode is chosen. The saved STL le will be used in SolidVerify to increase the simulation speed. The following options are available:
Save STL for every N job Save for marked job only

STL Delete mode This option enables you to delete the STL les created by the previous option. Never Delete the STL les will not be deleted. Delete on Simulation Close the STL les will be deleted when the Simulation is closed. Delete on Part Close the STL les will be deleted when the CAM-Part is closed. Convert parts with Rest Material from Ver. 8 to Ver. 9 This option enables you to dene how the CAM-Part with the Rest Material will be converted. Convert to Solid mode the CAM-Part will be converted to the Solid mode of the Stock Model Update. Do not convert the part will not be converted; the Z-Buffer mode will be used.

451

SolidCAM2005 Milling Users Guide

10. Settings

10.14 Tool Settings

Update Part tool table according to Machine Tool Table By setting this option the user instructs SolidCAM to automatically update the Part Tool Table with tools from the Machine tool table dened in the MACle, when the CNC-controller for the CAMPart is changed.

452

10. Settings

SolidCAM2005 Users Guide

Only used tools numbers This option enables you to update only those tools that were used in jobs. Tools that were not used will be removed from the Part Tool Table. Used tools that were not found in the Machine Tool Table will be numbered with the next sequential numbers.
Renumber tools from 1 when no machine tool table

The option removes all unused tools from the Part Tool Table. The used tools will be renumbered starting from number 1. If the Renumber tools from 1 when no Machine tool table option is not active, SolidCAM removes all unused tools from the Part Tool Table. The used tools will not be renumbered. This option is available only if the Only used tools numbers option is activated and only if the Machine Tool Table is not dened for the MAC of the new CNC-controller. Print in documentation - Only used tools. This option enables SolidCAM to include in the CAM-Part documentation only the tools from the Part Tool Table used in jobs. Show in CAM Manager This option enables you to display the tool headers in the CAM-Manager, whenever a new tool is used. The Tool Header is displayed before the job where the new tool is used.
Diameter

This option displays the tool diameter.

Type

This option displays the tool type.

Imprt tools
With tool number

This option enables you to import tools to the Part Tool table with their tool numbers. If this option is not checked, SolidCAM will assign a rst free number to the imported tool.

453

SolidCAM2005 Milling Users Guide

10. Settings

454

Index

SolidCAM2005 Milling Users Guide

Index
Symbols
2D simulation 394 3D Drill Job 387 3D Milling 309 3D Model Geometry 156 3D Simulation mode 406

A
Adding a Job 196 Adjacent tool path connection 264 Approach 246, 272 Approximation 434 Arc approximation 353, 373, 379 Auto-Save settings 440 Automatic Sort 218 Axis type 71

B
Boring 283

C
Calculate 213 CAM-Part 27 CAM-Part data dialog 28 CAM-Part Documentation 81 CAM-Part Lower level 53 CAM-Part name 29 CAM-Part Upper level 53 Chain 169 Chains direction 181 Chains sorting 183 Chain Direction 173 Chain Options dialog 172 Chain selection 172 Chain selection dialog 179 Chain selection settings 434 Chamfer 237 Check faces 318 Check Synchronization always 445 Check synchronization on user demand 445 Choose Faces dialog 318 Circular Pocket 368 Clean at 325 Clearance level 53 Clear offset 233 CNC-Controller 71 CNC-controllers settings 437

455

SolidCAM2005 Milling Users Guide

Index

Color Setup 438 Compare target and machined stock 415 Compensation 244, 270 Connection to CAD system 17 Connect islands 260 Connect type 300 Constant-Z 370 Constant-Z at oor machining 377 Constant-Z Tolerance 435 Constant-Z wall machining 371 Constraint 297 Contour Data dialog 258 Contour Roughing 341 Cross nish 354 Current Tool Table 89 Cutting direction 256, 366

D
Default CNC-controller settings 436 Default Geometry Names 447 Default Rest Material calculation method 448 Default tool data 115 Default Update Stock model method 448 Depth 204 Descent 328, 346 Descent Angle 299, 302 Diameter Offset Number 116 Directory 29 DNC settings 443 Documentation Editor 82 Dongle Update 21 Down Step 232, 251 Down step 325, 385 Drilling 282 Drill cycle type 281, 389 Drill depth 280 Drill Geometry 150 Drill Job 279 Drill points 333 Drive faces 318

E
Editors Settings 442 Engraving Data 301 Engraving depth 306 Engraving geometry 307 Engraving Job 382 Engraving Limit 306 Engraving technology 384 Equal distance 357 Exit Material 257 Export all tools to Excel 107

456

Index

SolidCAM2005 Milling Users Guide

Extend to edge 357 External program settings 441

F
Feed 116 Feed and Speed default 142 Fillet size for last cut 234 Finish cycle 300 Fixture 225 Fixture dialog 226 Floor Offset 270, 327

G
G-Code 426 Gap maximum 435 Gap minimum 435 Getting Help 25 Global holders table 114 Global shape-tools table 113

H
Hatch Data dialog 253 Hatch Roughing 340 Hidden line mode 413 Home 31 Home operations 56 Host CAD simulation mode 404 Hybrid mode 412

I
Import all tools from Excel 107 Installing SolidCAM 14 IPX Protocol 20 Island Offset 270

J
Job Group 214 Job Interface 197 Job Lower level 204 Job name 203 Job Sequence 216 Job Upper level 204

L
Length Offset number 116 License Server 20 Limits 302 Limit Data 303

457

SolidCAM2005 Milling Users Guide

Index

Limit Geometry 167 Linear nish 350 Local holders table 114 Local shape-tools table 113

M
Machine Tool Table 89 Machining area 304 Mac home number 33 Mac Options 69 Maximum down step 372 Message 209 Metric/Inch 433 Milling Levels 204 Minimal clean condition 269 Minimum down step 372 Mirror/Rotate point 208 Model Box 35 Model name 29 Model Reference 79 Multi-chain 169 Multi-Sided Home 31

N
Network License Installation 19

O
Offset cutting 356 Offset from model 389 Offset geometry 357 Offset on prole 232 Offset on surface 299 Open Pocket machining 334 Overlap 270, 299, 302, 325

P
Part Tool Table 89 Path 431 Peck 282 Pencil milling 380 Permanent tool 105 Plunging Pattern 268 Plunging pattern 342 Pocket Job 250 Pocket Types 252 Position 33 Post-processor les directory 436 Prole/Pocket Geometry 161 Prole Direction 246 Prole extension 246

458

Index

SolidCAM2005 Milling Users Guide

Prole Job 230 Program Folder 16 Program Number 75 Projections Mode 46

R
Radius compensation 244 Render mode 412 Rest Materal & SolidVerify Settings 448 Rest Material 237, 337 Rest material 59 Rest Material simulation mode 420 Retreat 246, 276 Roughing 324 Rough cycle 300

S
Scallop 299, 301, 372, 378 Section depth type 289 Section Geometry 165 Semi-Finish/Finish 343 Semi-Finish/Finish strategies 349 Sequence number 99 Settings 430 Setup Language 14 Setup mode 400 Shape-Tools dialog 131 Shaped Tools 130 Shaped Tool segments 136 Show/Hide Gouges 414 Show/Hide Split Solids 414 Simulation 392 Simulation Controls 393 Simulation menu 417 Simulation Mode 393, 400 Simulation Settings 444 Simulation speed 405 Simulation Toolbar 399 Single License Installation 14 Slot extension 289 Slot Geometry 164 Slot Job 286 Slot levels 289 Slot with constant depth 286 Slot with variable depth 286 SolidCAM Help 25 SolidCAM Manager 23 SolidVerify simulation mode 409 Spin 116 Spiral Finish 361 Spline approximation 171 Starting SolidCAM 22

459

SolidCAM2005 Milling Users Guide

Index

STL 417 STL Delete mode 449 STL Save mode 449 Stock model 58 Subroutine Number 75 Surface Curvature 323 Surface Data 298 Surface offset 301, 326 Surface tolerance 322 Synchronization 187 Synchronization check 188 Synchronization Settings 445 Synchronization Tolerance 446 System requirements 14

T
Tapping 283 Target model 59 TCP/IP Protocol 19 Tolerance 321, 383 Tools Filter 98 Tool Curvature 323 Tool data 108 Tool holders dialog 118 Tool Holder segments 124 Tool holding system 117 Tool Length 112 Tool Material 115 Tool number 99 Tool on working area 314 Tool options dialog 67 Tool path connections 360 Tool path tolerance 323 Tool Range 99 Tool Settings 450 Tool Side 243 Tool start level 53 Tool Tables 89 Tool Table dialog 97 Tool Types 86 Tool Z Level 54 Topology page 110 Translated Surface Job 293 Trochoidal milling 249

U
Units Settings 433 Update to Machine Tool table 106 Updating Stock Model 65 User Directories Settings 431 User Directory for SolidCAM-Parts 431 User Directory for SolidCAM-Tables 432

460

Index

SolidCAM2005 Milling Users Guide

V
VerifyPlus simulation 399

W
Wall nish 271 Wall Offset 270, 327 Wireframe Geometry 160 Wire mode 413 Working Area 162, 311 Working area dialog 312 Work Material 70

Z
Zero Compensation 245 Z Buffer 65 Z buffer 448

461

SolidCAM2005 Milling Users Guide

Index

Document Number: SCMUGENG05001

462