Scribd
Upload
7K views

RNC MML Commands

The document provides a list of 27 MML commands for troubleshooting issues on an RNC: 1) The first few commands check alarms, alarm history, unit states, software info, and IO device states. 2) Further commands monitor signaling links, SCCP subsystem states, database consistency, Iu-PS user plane ping times, VP numbers, and traffic monitoring. 3) The remaining commands check DCN in RNC, AAL2 endpoints, file transfers, resources, OMU logs, Iub usage, physical interface relations, and IMA groups.

Uploaded by

Sunil Gupta
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
7K views

RNC MML Commands

The document provides a list of 27 MML commands for troubleshooting issues on an RNC: 1) The first few commands check alarms, alarm history, unit states, software info, and IO device states. 2) Further commands monitor signaling links, SCCP subsystem states, database consistency, Iu-PS user plane ping times, VP numbers, and traffic monitoring. 3) The remaining commands check DCN in RNC, AAL2 endpoints, file transfers, resources, OMU logs, Iub usage, physical interface relations, and IMA groups.

Uploaded by

Sunil Gupta
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

RNC MML Commands

1) Active RNC+WBTS alarms ZAAP; 2) Active RNC alarms ZAAP: NR=1&&6999; 3) Alarm history since last midnight ZAHP; 4) Unit states ZUSI; ZUSI: FULL; 5) Software package info ZWQO: CR; 6) IO device states, SCSI & WDU should both be WO-EX. ZIHI; 7) External alarm definition ZAQT; 8) Command calendar ZICL; 9) Signaling links states ZNEL; 10) SCCP subsystem states, important that SGSN & MGW are AV-EX ZNHI; 11) Checking consistency of all databases ZDBS: BAIDAT, 0; ZDBS: EQDATA, 0; ZDBS: RAQUEL, 0; ZDBS: ARFILE, 1; 12) Ping SGSN from GTPU-0, GTPU-1, GTPU-2, GTPU-3 (ZQRX command) to check if Iu-PS user planes are working ZQRI: GTPU; Check valid IP addresses ZQRX: GTPU, 0: IP=<ip address from ZQRI command>; ZQRX: GTPU, 1: IP=<ip address from ZQRI command>; ZQRX: GTPU, 2: IP=<ip address from ZQRI command>; ZQRX: GTPU, 3: IP=<ip address from ZQRI command>;

13) CHECK VP NUMBERS IN RNC ZLCI :< if no>, VP; 14) Traffic monitoring: ZDDS: ICSU, 0; ? (Check if EXTENSION "BRM MONITORING" is listed) LP: 1, E2K (only needed if EXTENSION "BRM MONITORING" is not listed) ? (Check if EXTENSION "BRM MONITORING" is listed) 1 MCD :< wets-no>; MCD :<wbts-no>,6,0; BD :<wbts-no>; CTRL+c to stopZ 15) CELLS IN BL(S) can sometimes be released by lock/unlocked of VP ZLCI :<if no>,VP:<VP no>; (check current state) /Lock cells in RNW Object Browser. ZLCS:<if no>,<VP no>,:LOCKED;ZLCS:<if no>,<VP no>,:UNLOCKED; /Unlock cells in RNW Object Browser. 16)CHECK DCN in RNC ZQMI; ZQRI; ZQRL; 17) Check AAL2 Endpoint termination state ZRRI; ZLJI: ROU=<route found by ZRRI>; 18) Check statistical files transfer ZIFO: OMU: GENE00; ZIWX: NODEF: VIDAST: %, %; (Check actual file sizes) ZIFI: OMU: GENE00; (Check defined file size etc.) 19) Resources in RNC ZWXI; 20) OMU Computer log ZDDS; 00-MAN>GSC 21) Check traffic in NIS1 ZDDS: NIS1 (P), <no>; 0069-$ loudest bar 0069-$ bar rconn 2

/Note printout shows VP, VC in hex 22) Check Iub usage ZDDS: RSMU,<active rsmu>; ZLP: 5, EPU 5 LRC :< route no>; 23) Check relation between SET (phy if), PHY TTP, ATM IF, Connected NE ZLAI; ZYDI; ZYWI; if protected SDH ZNEL; to find to where an ATM IF is connected 24) To interrogate & make modification with IMA Group ( ZYBI,ZYBM ) 25) ZQMI; 26) ZLAI; 27) ZLCJ;

You might also like