Scribd
Upload
577 views

Opcom Injector Programming

This document provides instructions for programming injector codes on various Opel/Vauxhall vehicle models after replacing fuel injectors. It explains that the engine control unit must be coded with the new injector codes to ensure proper operation. The injector codes consist of letters and numbers written on the injectors. The process involves reading out the current codes, changing one code at a time to the new value, and verifying the programming by reading codes again.

Uploaded by

Iván Blanco Fernández
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
577 views

Opcom Injector Programming

This document provides instructions for programming injector codes on various Opel/Vauxhall vehicle models after replacing fuel injectors. It explains that the engine control unit must be coded with the new injector codes to ensure proper operation. The injector codes consist of letters and numbers written on the injectors. The process involves reading out the current codes, changing one code at a time to the new value, and verifying the programming by reading codes again.

Uploaded by

Iván Blanco Fernández
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Opcom Injector Programming

Omega-B
Y25DT There is no need to manually enter the injector codes on these. You need to execute the '''[Injectrs were replaced]''' diagnostic procedure from the menu to code the replaced injectors.

Astra-G
Z17DLT There is no need to manually enter the injector codes on these.

Astra-H / Zafira-B
Z17DTH/Z17DTL On these, you do not need to enter the quantity adjustment codes, for each injector. All you need to do, is to choose, which injector was replaced. Available options are 1, 2, 3, 4, or all. Z19DT/Z19DTH/Z19DTL/Z19DTJ The procedure is the same, as the Vectra-C / Signum

Vectra-C / Signum
Z19DT/Z19DTH/Z19DTL/Z19DTJ The injector code, which contains 9 letters is written on the injector itself. When you replace these injectors, the engine control unit must be coded, to ensure the proper operation of these EDC16 injectors. The injector code consist of 9 letters, using the following character table:

A,B,C,D,E,F,G,H,I,K,L,M,N,O,P,R,S,T,U,V,W,X,Y,Z,1,2,3,4,5,6,7,8
An example injector code: 81SPBF7AA

Corsa-C / Meriva
Z17DTH The injector code, which contains 22 letters (11 hexadecimal numbers) is written on the injector itself. When you replace these injectors, the engine control unit must be coded, to ensure the proper operation of these DEC30 injectors. The injector code consist of 22 letters, using the following character table:

0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F
An example injector code: D500CA0000BECEEBD7CDCE

Z13DTH The injector code, which contains 9 letters is written on the injector itself.

When you replace these injectors, the engine control unit must be coded, to ensure the proper operation of these MultiJET injectors. The injector code consist of 9 letters, using the following character table:

A,B,C,D,E,F,G,H,I,K,L,M,N,O,P,R,S,T,U,V,W,X,Y,Z,1,2,3,4,5,6,7,8
An example injector code: BKAPM2EC8 When a MultiJET engine ECU is opened for diagnostic, the following window will appear:

Click on the [Programming] button, to read-out the stored injector codes.

Please ensure, that Ignition is ON, and engine is NOT running. On this window, youll see the current injector quantity adjustment codes, for each cylinder. Please only change one adjustment code at once, then click on the corresponding [Change] button. The result of the programming will be displayed correctly. After programming, cycle igniton, and then read out the stored injector codes again, to verify the programming process.

You might also like