Scribd
Upload
457 views

Siemens Commands

The document lists the milling and turning commands, parameters, and cycles supported in the Siemens 840(New) control. Key commands include G-codes for positioning, tool radius compensation, coordinate systems, and feedrates. Supported milling cycles include drilling, boring, tapping, and pocketing cycles. Supported turning cycles include drilling, boring, grooving, threading and stock removal cycles.

Uploaded by

emaster1
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
457 views

Siemens Commands

The document lists the milling and turning commands, parameters, and cycles supported in the Siemens 840(New) control. Key commands include G-codes for positioning, tool radius compensation, coordinate systems, and feedrates. Supported milling cycles include drilling, boring, tapping, and pocketing cycles. Supported turning cycles include drilling, boring, grooving, threading and stock removal cycles.

Uploaded by

emaster1
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 4

Siemens 840(New) milling and turning commands.

G0 G1 Parameters: Angle ANG= , A, Round RND=, R, B Chamfer CHF=, CHR=, -B, -D G2/G3 CIP G4 G17/G18/G19 G33 (LATHE) G40 G41 G42 G500 G54/G55/G56/G57 G58/G59 (same as previous) G70/G71 G700/G710 G90/G91 G93/G94/G95 G96/G97 G961/G971 G937 Commands supported: TRANS ATRANS ROT AROT RPL

SCALE ASCALE MIRROR AMIRROR RET GOTO GOTOC GOTOB GOTOF =AC(), =IC() syntax is allowed Subroutines call by name are allowed (without parameters). Mathematical expressions with R numbers are allowed (also in subroutines and cycles call). M2/M17/M30 M3/M4/M5/M6/M66 M8/M9/M19 M96/M97/M98/M99 Cycles: MCALL modificator allowed. Milling cycles: Supported: CYCLE81 Drilling,centering CYCLE801 CYCLE82 Drilling, counterboring CYCLE83 Deep-hole drilling CYCLE84 Rigid tapping CYCLE840Tapping with compensating chuck CYCLE85 Boring 1 CYCLE86 Boring 2 CYCLE87 Boring 3 CYCLE88 Boring 4 CYCLE89 Boring 5 CYCLE90 Thread milling POCKET1 Rectangular pockets

POCKET2 POCKET3 POCKET4 HOLES1 HOLES2

Circular pockets Rectangular pocket Circular pocket

Not supported: LONGHOLE SLOT1 Slots on a circle SLOT2 Circumferential slot CYCLE71 Face milling CYCLE72 Path milling CYCLE76 Rectangular spigot milling CYCLE77 Circular spigot milling CYCLE73 Pocket milling with islands CYCLE74 Pocket milling with islands CYCLE75 Pocket milling with islands CYCLE800 Swiveling CYCLE832 High speed settings CYCLE60 Engraving cycle CYCLE899 Trochoidal milling Turning cycles: CYCLE81 Drilling,centering CYCLE82 Drilling, counterboring CYCLE83 Deep-hole drilling CYCLE84 Rigid tapping CYCLE840Tapping with compensating chuck CYCLE85 Boring 1 CYCLE86 Boring 2 CYCLE87 Boring 3 CYCLE88 Boring 4 CYCLE89 Boring 5 CYCLE93 Grooving cycle CYCLE94 Undercut cycle CYCLE95 Stock removal cycle CYCLE97 Thread cutting Turning L-cycles: L95/L96 Stock removal L97 Threading Not supported: CYCLE96 Thread undercut

CYCLE98 CYCLE950

Thread chaining Extended stock removal

You might also like