Scribd
Upload
171 views

Cone To Shell Reinforcement

The document provides design specifications for reinforcing the junction between a large cylinder and small cylinder. It includes dimensions, material properties, loads, and calculations to determine the required reinforcement area. The key information is: - Dimensions and properties of the cylinders and cone section joining them - External design pressure and temperature - Axial loads on each cylinder end due to wind - Calculations to determine the equivalent area, required moment of inertia, and required reinforcement area to strengthen the junction - Specifications for placing a stiffening ring around the junction within a certain distance

Uploaded by

Sajal Kulshrestha
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
171 views

Cone To Shell Reinforcement

The document provides design specifications for reinforcing the junction between a large cylinder and small cylinder. It includes dimensions, material properties, loads, and calculations to determine the required reinforcement area. The key information is: - Dimensions and properties of the cylinders and cone section joining them - External design pressure and temperature - Axial loads on each cylinder end due to wind - Calculations to determine the equivalent area, required moment of inertia, and required reinforcement area to strengthen the junction - Specifications for placing a stiffening ring around the junction within a certain distance

Uploaded by

Sajal Kulshrestha
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 4

GODREJ & BOYCE VIKHROLI REINFORCEMENT AT CONE TO CYLINDER JUCNTION Deign Data External Design pressure Design temperature

Outside Diameter of Large Cylinder Outside Diameter of Small Cylinder Axial Length of cone Design Length of Large vessel section Design Length of Small vessel section Joint efficiency of shell & cone Material of cone & shell Allowable stress of material at Design temp Modulus of Elasticity Minimum thickness required for Large cylinnder Minimum thickness required for Small cylinnder Minimum thickness required for Cone Thickness specifeid for Cone Thickness specifeid for Large cylinder Thickness specifeid for Small cylinder Axial Load due to wind at Large End Axial Load due to wind at Small End Compression Ring Material Allowable stress of material at Design temp Outside Radius of Large End Outside Radius of Small End Junction at Large Cylinder Now From table Half apex angle REINFOREMENT IS NEEDED Calculating Equivaent Area of Cylinder and cone

Pe T Dl Ds Lc Ll Ls E ----Ss E' trl trs trc tc tl ts fl fs ---Sr Rl Rs

= = = = = = = = = = = = = = = = = = = = = = =

15 86 96 48 48 120 224 0.7 SA 240 - 316 13800 30000000 0.25 0.1875 0.25 0.25 0.25 0.25 100 30 SA 240 - 316 12700 48 24

Pe/S.E d a

= = = =

15 / 13800 * 0.7 0.0016 4 26.56505118

Atl

= =

(Ll.ts)/2 + (Lc.tc)/2 21
2

Factor M Factor Fl

M Fl

= = = =

-(Rl.tana)/2 + (Ll/2) + (Rl - R 60 Pe.M + f1.tana 950

Factor B Factor A Required Moment of Inertia Factor k Factor Q

B A Ireq k Ql

= = = = = = = =

0.75xFl.Dl/Atl 3257.142857 0.0003 A.Dl2.Atl / 10.9 5.326678899 Ss.E' / Sr.E' 1.09 (Pe.Rl)/2 + f1 460

Required Area of reinforcement

Areq

= =

(k.Ql.Rl.tana/Ss.E)*[1-0.25(P 1.219

INSERT STIFFNING RING CALCULATION TABLE N DIAG

Reinforcement shall be within the distance from the junction Centroid of ring shall be within a distance from the junction Distance from which the ring is placed from the junction ring is safely placed

x x1 x2

= = = = =

(Rl.ts)1/2 3.464 0.25x 0.866 0.98

ON

psi F in in in in in

psi psi in in in in in in lb/in lb/in

(refer page (refer page

) )

psi in in

/ 13800 * 0.7

l.ts)/2 + (Lc.tc)/2 in2


2 2

Rl.tana)/2 + (Ll/2) + (Rl - Rs )/(3Rl.tana)

.M + f1.tana

(from chart

at )

Dl2.Atl / 10.9 in4

Ql.Rl.tana/Ss.E)*[1-0.25(Pe.Rl-Ql)/Ql* (d/a)] in
2

in in in

You might also like