Scribd
Upload
997 views

p /γ + z + v /2g + = p /γ + z + v /2g: Parallel Pipeline Systems

The document discusses parallel pipeline systems where flow occurs through multiple pathways simultaneously. It states the key equations that apply to parallel systems, including continuity and head loss equations. It explains that parallel systems with two branches can be solved using two equations, but systems with three or more branches, called networks, are indeterminate and require more complex solutions like the Hardy Cross method. The Hardy Cross method is then outlined, involving expressing head loss in terms of flow, dividing the network into circuits, calculating head losses and flow adjustments iteratively until convergence.

Uploaded by

anirbanpwd76
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
997 views

p /γ + z + v /2g + = p /γ + z + v /2g: Parallel Pipeline Systems

The document discusses parallel pipeline systems where flow occurs through multiple pathways simultaneously. It states the key equations that apply to parallel systems, including continuity and head loss equations. It explains that parallel systems with two branches can be solved using two equations, but systems with three or more branches, called networks, are indeterminate and require more complex solutions like the Hardy Cross method. The Hardy Cross method is then outlined, involving expressing head loss in terms of flow, dividing the network into circuits, calculating head losses and flow adjustments iteratively until convergence.

Uploaded by

anirbanpwd76
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

PARALLEL PIPELINE SYSTEMS

Where flow occurs through along more than one pathway.

The principle of continuity still applies Q1 = Q2 = Qa + Qb + Qc Again the GE equation can be applied between points 1 and 2

p1/ + z1 + v12/2g + hL = p2/ + z2 + v22/2g

All elements of flow converging at 2 WILL have the same head loss. The flow will adjust automatically so that the head loss in each branch pipe WILL BE THE SAME! 1

hL = ha = hb = hc

So essentially we have 2 equations to solve parallel pipe systems - discharge equation - head loss equation So when we have a parallel system with two branches (2 unknowns Q) we can easily compute the values. However, for system with more than 2 branches the computations become complex! Systems with 3 or more branches called NETWORKS NETWORKS are INDETERMINATE! Why because the number of unknowns are more than the 2 equations available. Solutions for NETWORKS HARDY CROSS method.

System with 2 branches

Procedure for computations 1. Set up the conservation of mass equation Q1 = Q2 = Qa + Qb 2. Express Q in terms of area and velocity of pipe Qa = Aa * Va; Qb = Ab * Vb 3. Determine the hL for each pipe in terms of the velocity (V). You will have to ASSUME a friction factor. 4. Equate the head losses for the pipes. ha = hb 3

Using this equation get Va in terms of Vb or vice-versa. 5. Now introduce this info for equation in step 1 and compute one of the velocities. 6. Using equation from step 4, compute the other velocity. 7. Compute Q values. 8. Check your friction factors; iterate if necessary.

EXAMPLE PROBLEM 12.1

100 gal/min of water at 60F is flowing in a 2-inch sch 40 pipe at section 1. The heat exchanger in branch a has a loss coefficient K = 7.5 based on the velocity head in the pipe. All three valves are wide open. Branch b is a 1 inch sch 40 pipe. Elbows are standard. The length of pipe between points 1 and 2 for branch b is 20 ft. Because of the size of the heat exchanger the length of the pipe in branch a is short and friction loss can be neglected. For this arrangement, determine (a) volume flow rate Q in each branch; (b) pressure drop between points 1 and 2.

Assignment # 8 12.1M

HARDY CROSS METHOD for 3 branches or more (NETWORKS)

Procedure set up to solve Networks. You have to express the head loss h in terms of Q h = kQn We already express h in terms of v; and v = Q/A We have estimate the volume Q in the pipes. Estimation is based on the principle of conservation of volume and the likely losses that may occur in the pipe. You have to divide the network into closed circuits and assign +ve and ve values to head loss in the pipes.

Rule If flow in a given pipe of a circuit is clockwise, Q and h are positive. If flow is counterclockwise, Q and h are negative.

Stepwise procedure for Hardy Cross Method 1. Express energy loss in each pipe by h = kQ2 2. Assume values of Q for each pipe. 3. Divide the network into closed circuits.

4. For each pipe calculate head loss using h = kQ2 5. For each circuit, algebraically sum the values of h using the direction convention/rule. Find h. 6. For each pipe calculate 2kQ 7. Sum all values of 2kQ for each circuit, assuming all are positive = 2kQ 8. For each circuit calculate

h Q = 2kQ
9. for each pipe calculate Q = Q Q 10. Repeat until Q becomes very small.

10

11

12

You might also like