Scribd
Upload
79 views

Understanding The Concept of The Gear Ratio: 1.27 Inches / 2 0.635 Inches

Understanding gear ratios involves understanding the relationship between the circumference of circles with different diameters. A gear with half the diameter of another gear must rotate twice to cover the same distance, demonstrating a gear ratio of 2:1. Teeth on gears allow for precise gear ratios based on tooth counts, prevent slippage between gears, and make gear ratios less dependent on imperfect diameters. A figure shows a gear with twice the diameter of another rotating at half the speed, visually depicting a 2:1 gear ratio.

Uploaded by

BookMaggot
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
79 views

Understanding The Concept of The Gear Ratio: 1.27 Inches / 2 0.635 Inches

Understanding gear ratios involves understanding the relationship between the circumference of circles with different diameters. A gear with half the diameter of another gear must rotate twice to cover the same distance, demonstrating a gear ratio of 2:1. Teeth on gears allow for precise gear ratios based on tooth counts, prevent slippage between gears, and make gear ratios less dependent on imperfect diameters. A figure shows a gear with twice the diameter of another rotating at half the speed, visually depicting a 2:1 gear ratio.

Uploaded by

BookMaggot
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 1

Understanding the concept of the gear ratio

Understanding the concept of the gear ratio is easy if you understand the concept of the circumferenceof a circle. Keep in mind that the circumference of a circle is equal to the diameter of the circle multiplied by Pi (Pi is equal to 3.14159...). Therefore, if you have a circle or a gear with a diameter of one inch, the circumference of that circle will be 3.14159 inches. The following figure shows how the circumference of a circle with a diameter of 1.27 inches is equal to a linear distance of 4 inches:

Let's say that you had another circle whose diameter was 1.27 inches / 2 = 0.635 inches, and you rolled it in the same way as in this figure. You would find that, because its diameter is one half of the circle's in the figure, it has to complete two full rotations to cover the same 4 inch line. This explains why two gears, one half as big as the other, have a gear ratio of 2:1. The smaller gear has to spin twice to cover the same distance covered when the larger gear spins once.
Most gears that you see in real life have teeth. The teeth have three advantages: 1. They prevent slippage between the gears - therefore axles connected by gears are always synchronized exactly with one another. 2. They make it possible to determine exact gear ratios - you just count the number of teeth in the two gears and divide. So if one gear has 60 teeth and another has 20, the gear ratio when these two gears are connected together is 3:1. 3. They make it so that slight imperfections in the actual diameter and circumference of two gears don't matter. The gear ratio is controlled by the number of teeth even if the diameters are a bit off.

ou can see effects 1, 2 and 3 in the figure above. In this figure, you can see that the two gears are rotating in opposite directions, that the smaller gear is spinning twice as fast as the larger gear, and that the axis of rotation of the smaller gear is to the right of the axis of rotation for the larger gear. The fact that one gear is spinning twice as fast as the other results from the ratio between the gears, or the gear ratio. In this figure, the diameter of the gear on the left is twice that of the gear on the right. The gear ratio is therefore 2:1 (pronounced "two to one"). If you watch the figure you can see the ratio: Every time the larger gear goes around once, the smaller gear goes around twice. You can see that if both gears had the same diameter, they would rotate at the same speed but in opposite directions.

You might also like