Scribd
Upload
97 views

(WWW - Entrance-Exam - Net) - PTU M.Tech in Production Engineering Non Conventional Machining Processes Sample Paper 1 PDF

The document is a question paper for an M.Tech exam on non-conventional machining processes. It contains 8 questions, with students instructed to attempt any 5. The questions cover topics such as abrasive jet machining, ultrasonic machining, chemical machining, electrochemical machining, electrical discharge machining, laser beam machining, electron beam machining, and explosive forming. Formulas for material removal rate in electrochemical machining and ultrasonic machining are also asked to be derived.

Uploaded by

Abdur Rahman
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
97 views

(WWW - Entrance-Exam - Net) - PTU M.Tech in Production Engineering Non Conventional Machining Processes Sample Paper 1 PDF

The document is a question paper for an M.Tech exam on non-conventional machining processes. It contains 8 questions, with students instructed to attempt any 5. The questions cover topics such as abrasive jet machining, ultrasonic machining, chemical machining, electrochemical machining, electrical discharge machining, laser beam machining, electron beam machining, and explosive forming. Formulas for material removal rate in electrochemical machining and ultrasonic machining are also asked to be derived.

Uploaded by

Abdur Rahman
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Paper ID [PES07]

(Please fill this Paper ID in OMR Sheet)

M. Tech.
NON-CONVENTIONAL
Time: 03 Hours Instruction 1) 2) Ql) to Candidates: Attempt any Five Questions. All questions carry equal marks.

MACHINING. PROCESSES (PE


..

507)

Maximum Marks: 100

(a) Sketch and explain- the schematic diagram .

ofAIM

system.

(b) Why different abrasives produce different MRR. (c) Discuss the reasons for inaccuracies in AIM process. Q2) (a) If suppose USM is used for drilling a hole (under the same machining conditions) in Aluminium and Cast Iron. Which one will ~ave higher
depth of the drilled hole and why?
.

(b) Explain the functions of 'Horn' in USM. (c) What do you understand by , transducer' and 'magnetostriction effects' ? Q3) (a) Explain various parameters that influence the performance of chemical machining process. (b) Write in tabular form the basic differences between chemical and electrochemical processes.
. .

(c) Why surface finish obtained in case of chemical machining of alloys is poor? Explain in brief. Q4) (~) Discuss the mechanism of material removal in EDM prbcess. (b) What are the different ways of gap-flushing used in EDM? (c) Discuss the factors influencing the choice of electrode material in EDM. Name the best electrode material forIinish machining a small die made of WC by EDM.

'""'

Q5) (a) Explain the effect of 'focusing' on the performance of laser beam machining. (b) What are the different beam manipulation devices used for laser processing of material. (c) Explain the principle of laser beam. Q6) (a) Explain why vacuum is needed in Electron beam process and also tell its order. (b) Write the specific applications of EBM. (c) How the work table is protected from getting damaged by the electron beam which has completely penetrated the workpiece:
Q7) (a) Explain the basic principle behind the explosive forming. (b) What are the types of pulse - generators used in Electric Discharge machining? Discuss the merits and demerits of each one of them.

Q8) (a) Derive a theoretical relationship for the determination of the MRR in Electro-Chemical Machining. (b) Derive an expression for MRR in working of ductile material using USM.

You might also like