Scribd
Upload
254 views1 page

CNC Package Datasheet 2

This document provides a simplified wiring diagram for a common 3-axis CNC device that uses a parallel port for control. It outlines the typical connections between a KL4030 driver board, a C10 breakout board, stepper motors, limit switches and an emergency stop button. Additional details are provided on power supply requirements, direction control and wiring conventions.

Uploaded by

kairotdf
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
254 views1 page

CNC Package Datasheet 2

This document provides a simplified wiring diagram for a common 3-axis CNC device that uses a parallel port for control. It outlines the typical connections between a KL4030 driver board, a C10 breakout board, stepper motors, limit switches and an emergency stop button. Additional details are provided on power supply requirements, direction control and wiring conventions.

Uploaded by

kairotdf
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Electronic Products for CNC and Automation

Simplified Wiring Diagram


Parallel Port IO
This can be very sysem specic, but for a common 3-axis parallel port controlled CNC device, the following chart can be a starting point.
All driver logic active-lo

Keling Inc.

KL4030 Based 3 & 4 Axis CNC Packages


Keling

KL-201-24

Switching DC Power Supply


DC Output

24v 8.5amps
AC Input N L

V Adj

+24 V

Ground(-v)

AC Plug

Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Direc on Output Output Output Output Output Output Output Output Output Input Input Input Input

Purpose Spindle Control Relay X Direc on X Step Y Direc on Y Step Z Direc on Z Step
KL-4030
VCC GND A+ AB+ B(Enable)Rest(Enable)Rest+ (Dir) CW(Dir) CW+ (Step) CP (Step) CP +
Kelling Technology Inc .

Blue \White & White\Red Blue & Red Green \White & Black\White Green & Black

+24v Ground

Step Motor
LPT1-2 LPT1-3

E-Stop Limit X Limit Y Limit Z

C10 Breakout Board Jumpers


JP1 selects the direction for parallel port pins 2 through 9. This is useful when using multiple breakout boards and parallel ports.

EU AC Wire Colors
Ground, or Earth is always Green/Yellow Live is Always Brown Neutral is Blue

US AC Wire Colors
Ground, or Earth is Usually Green Live is usuall Black Neutral is usually White

E-STOP

INPUT
5 v 13 5 v 15 5v GND 5 v EN

12

Wiring Hints
Common isnt always Ground!

In this case we are wiring active low. That means the driver board steps when it senses a pin pulled low, you will notice that the power setting on the breakout board is set for common +5v, which is provided to the CW+ and CP+ terminals on the 4030 driver module.

C10 Breakout board power source


The buer chips on the C10 require +5vdc for operation, hence the additional power supply. A voltage regulator circuit such as a 7805 can be used instead. Additionally, the C10 requires +5v on the enable input, otherwise the buer ICs will not pass data from the PC.

E-Stop: Normally closed?


If possible, a normall closed button pulling an input high should be uvsed for an E-stop. This way, if the power to the machine fails, the PC will see the input pin go low and report an emergency stop.

www.kelinginc.net

KL4030 Based 3 & 4 Axis CNC Packages

OUTPUT
1&2 = COM GND 2&3 = COM 5vdc

+5

17 GND 16

14 GND 1

2 COM 3 4 COM 5 6 C OM 7 COM 8 C OM 9 COM 10 5v 11 5v

JP2 321

JP1 321
C10 PARALL EL PORT INTERFACE CARD

1&2 = 2-9 out 2&3 =2-9 in

DB25 Parallel Port

INPUT/OUTPUT

5vdc Wall Transformer

2/2

You might also like