1.054/1.541 Mechanics and Design of Concrete Structures Prof.

Oral Buyukozturk

Spring 2004 Outline 1 Massachusetts Institute of Technology

1.054/1.541 Mechanics and Design of Concrete Structures (3-0-9) Outline 1 Introduction / Design Criteria for Reinforced Concrete Structures

Structural design
o Definition of design: Determination of the general shape and all specific dimensions of a particular structure so that it will perform the function for which it is created and will safely withstand the influences which will act on it throughout its useful life. Principles of mechanics, structural analysis, behavioral knowledge in structures and materials. Engineering experience and intuition. (a) Function, (b) strength with safety requirements will vary for structures. Influences and structural response: Influences
Loads Temperature fluctuations Foundation settlements Time effects Corrosion Earthquakes Other environmental effects

Structure

Structural response
Failure (strength) Failure mode Deformations Cracking Stresses Motion

o Structural mechanics: A tool that permits one to predict the response (with a required level of accuracy, and a good degree of certainty) of a structure to defined influences.

1 /7

1.054/1.541 Mechanics and Design of Concrete Structures Prof. Oral Buyukozturk

Spring 2004 Outline 1

o Role of the designer (engineer) of a structure

Design criteria for concrete

o Two schools of thoughts 1. Base strength predictions on nonlinear theory using actual -

relation
1897 M.R. von Thullie (flexural theory) 1899 W. Ritter (parabolic stress distribution theory] 1900 E. Coignet and N. de Tedesco (the straight-line (elastic) theory of concrete behavior) o Working Stress Design (WSD) Elastic theory 1. Assess loads (service loads) (Building Code Requirements) 2. Use linear elastic analysis techniques to obtain the resulting internal forces (load effects): bending, axial force, shear, torsion At service loads: max all
c e.g. all = 0.45 f c' compression in bending

2. Straight-line theory (elastic)

s all = 0.50 f y flexure

o Ultimate Strength Design (USD) The members are designed taking inelastic strain into account to reach ultimate strength when an ultimate load is applied to the structure. The load effects at the ultimate load may be found by (a) assuming a linear-elastic behavior (b) taking into account the nonlinear redistribution of actions. Sectional design is based on ultimate load conditions. Some reasons for the trend towards USD are (a) Efficient distribution of stresses 2 /7

1.054/1.541 Mechanics and Design of Concrete Structures Prof. Oral Buyukozturk

Spring 2004 Outline 1

(b) Allows a more rational selection of the load factors (c) Allows designer to assess the ductility of the structure in the post-elastic range o Limit State Design Serviceability limit state: Deformation, fatigue, ductility. Ultimate limit state: Strength, plastic collapse, brittle fracture, instability, etc. It has been recognized that the design approach for reinforced concrete (RC) ideally should combine the best features of ultimate strength and working stress designs: (a) strength at ultimate load (b) deflections at service load (c) crack widths at service load o ACI (American Concrete Institute) Code emphasizes: (a) strength provisions (b) serviceability provisions (deflections, crack widths) (c) ductility provisions (stress redistribution, ductile failure)

Design factors
o 1956 A.L.L. Baker (simplified method of safety factor determination) o 1971 ACI Code (load factors and capacity (strength, resistance) reduction factors) o 2002 ACI 318 Building Code o Design loads (U) are factored to ensure the safety and reliability of structural performance. o Structural capacities () of concrete material are reduced to account for inaccuracies in construction and variations in properties.

3 /7

1.054/1.541 Mechanics and Design of Concrete Structures Prof. Oral Buyukozturk

Spring 2004 Outline 1

Safety
o Semi-probabilistic design is achieved by introducing the use of load factors, l , and capacity reduction factors, . o Load factors ACI 318 Building Code Load combinations U = 1.4(D + F) U = 1.2(D + F + T) + 1.6(L + H) + 0.5(Lr or S or R) U = 1.2D + 1.6(Lr or S or R) + (1.0L or 0.8W) U = 1.2D + 1.6W + 0.5L + 1.0(Lr or S or R) U = 1.2D + 1.0E + 1.0L + 0.2S U = 0.9D + 1.6W + 1.6H U = 0.9D + 1.0E + 1.6H where D = dead load; F = lateral fluid pressure; T = self-straining force (creep, shrinkage, and temperature effects); L = live load; H = load due to the weight and lateral pressure of soil and water in soil; Lr = roof load; S = snow load; R = rain load; W = wind load; E = earthquake load. ACI 318-02 also provides exceptions to the values in above expressions. o Capacity reduction factors ACI 318 Building Code Members subject to structural actions and their associated reduction factor () Beam or slab in bending or flexure: 0.9 Columns with ties: 0.65 Columns with spirals: 0.70 Columns carrying very small axial loads: 0.65~0.9 for tie stirrups and 0.7~0.9 for spiral stirrups. Beam in shear and torsion: 0.75

4 /7

1.054/1.541 Mechanics and Design of Concrete Structures Prof. Oral Buyukozturk

Spring 2004 Outline 1

Relation between resistance capacity and load effects

Rn i li resistance sum of load effects

i =1

For a structure loaded by dead and live loads the overall safety factor is s= 1.2 D + 1.6 L 1 D+L

Making of concrete
o Cements Portland cements Non-portland cements

o Aggregates Coarse and fine o Water o Chemical admixtures Accelerating admixtures Air-entraining admixtures Water-reducing and set-controlling admixtures Finely divided admixtures Polymers (for polymer-modified concrete) Superplasticizers Silica-fume admixture (for high-strength concrete) Corrosion inhibitors

Raw material components of cement

o Lime (CaO) o Silica (SiO2) o Alumina (Al2O3)

Properties of portland cement components

5 /7

1.054/1.541 Mechanics and Design of Concrete Structures Prof. Oral Buyukozturk Rate of Component Heat liberated reaction

Spring 2004 Outline 1 Ultimate cementing value

Tricalcium silicate, C3S Dicalcium silicate, C2S Tricalcium aluminate, C3A Tetracalium aluminoferrate, C4AF

Medium Slow Fast Slow

Medium Small Large Small

Good Good Poor Poor

Types of portland cements

o Type I: All-purpose cement o Type II: Comparatively low heat liberation; used in large structures o Type III: High strength in 3 days o Type IV: Used in mass concrete dams o Type V: Used in sewers and structure exposed to sulfates

Mixture design methods of concrete

o ACI method of mixture design for normal strength concrete o Portland Cement Association (PCA) method of mixture design

Quality tests on concrete

o Workability o Air content o Compressive strength of hardened concrete o Flexural strength of plain concrete beams o Tensile strength from splitting tests

Advantages and disadvantages of concrete

o Advantages Ability to be cast Economical 6 /7

1.054/1.541 Mechanics and Design of Concrete Structures Prof. Oral Buyukozturk

Spring 2004 Outline 1

Durable Fire resistant Energy efficient On-site fabrication Aesthetic properties Low tensile strength Low ductility Volume instability Low strength-to-weight ratio

o Disadvantages

Properties of steel reinforcement

o Youngs modulus, Es o Yield strength, fy o Ultimate strength, fu o Steel grade o Geometrical properties (diameter, surface treatment)

Types of reinforced concrete structural systems

o Beam-column systems o Slab and shell systems o Wall systems o Foundation systems

7 /7