10/31/2011

IES 2001

Lathe
BySKMondal

Thespindlespeedrangeinageneralpurposelathe isdividedintostepswhichapproximatelyfollow (a) Arithmeticprogression (b) Geometricprogression (c) Harmonicprogression (d) Logarithmicprogression

IES 1992
Feedgearboxforascrewcuttinglatheisdesigned onthebasisof (a) Geometricprogression (b) Arithmeticprogression (c) Harmonicprogression (d) None.

Example
How much machining time will be required to reduce the diameter of a cast iron rod from 120 mm to 116 mm over a length of 100 mm by turning using a carbide insert. Cutting velocity is 100 m/min and feed rate = 0.2 mm/rev.

IES2010
In turning a solid round bar, if the travel of the cutting tool in the direction of feed motion is 1000 mm, rotational p of the workpiece p is 5 500 rpm, p , and speed rate of feed is 0.2 mm/revolution, then the machining time will be (a) 10 seconds (b) 100 seconds (c) 5 minutes (d) 10 minutes

IES 2003
The time taken to face a workpiece of 72 mm diameter, if the spindle speed is 80 r.p.m. and cross feed is 0.3 mm/rev, is (a) 1.5 minutes (b) 3.0 minutes ( ) 5.4 minutes (c) i t (d) 8.5 8 minutes i t

Page 1 of 69

10/31/2011

IAS 2002
A 150 mm long, 12 mm diameter 304 stainless steel rod is being reduced in diameter to 115 mm by turning on a lathe. The spindle rotates at N = 400 rpm and the tool is travelling at an axial speed of 200 mm/min. The time taken for cutting is given by (a) 30 s (b) 36 s (c) 1 minute (d) 45 s

IES 2004
A medium carbon steel workpiece is turned on a lathe at 50 m/min. cutting speed 0.8 mm/rev feed and 1.5 mm depth of cut. What is the rate of metal removal? (a) 1000 mm3/min (b) 60,000 mm3/min (c) 20,000 mm3/min (d) Can not be calculated with the given data

IES 2006
For taper turning on centre lathes, the method of swiveling the compound rest is preferred for: (a) Long jobs with small taper angles (b) Long jobs with steep taper angles (c) Short jobs with small taper angles (d) Short jobs with steep taper angles

Example
Find the angle at which the compound rest should be set up to turn taper on the workpiece having a length of 200 mm, larger diameter 45 mm and the smaller 30 mm.

IES 1992
Tailstocksetovermethodoftaperturningis preferredfor (a) Internaltapers (b) Smalltapers (c) Longslendertapers (d) Steeptapers

IAS 2002
The amount of offset of tail stock for turning taper on full length of a job 300 mm long which is to have its two diameters at 50 mm and 38 mm ultimately is (a) 6 mm (b) 12 mm ( ) 25 mm (c) (d) 44 mm

Page 2 of 69

10/31/2011

IES 1998
A 400 mm long shaft has a 100 mm tapered step at the middle with 4 included angle. The tailstock offset required to produce this taper on a lathe would be (a) 400 sin 4 4 (b) 400 sin 2 2 (c) 100 sin 4 (d) 100 sin 2

IES2010
The effect of centering error when the tool is set above the center line as shown in the figure results effectively in 1. Increase in rake angle. 2. Reduction R d i in i rake k angle. l 3. Increase in clearance angle. 4. Reduction in clearance angle. Which of these statements is/are correct? (a) 1 only (b) 1 and 4 only (c) 2 and 4 only (d) 1, 2, 3 and 4

GATE 2002
A leadscrew with half nuts in a lathe, free to rotate in both directions has (a) Vthreads (b) Whitworth threads (c) Buttress threads (d) ACME threads

GATE 2008
The figure shows an incomplete schematic of a conventional lathe to be used for cutting threads with different pitches. The speed gear box Uv, is shown and the feed gear box Us, is to be placed. P, Q. R and S denote locations and have no other significance. Changes in Uv, should NOT affect the pitch of the thread being cut and changes in Us, should NOT affect the cutting speed.

Contd..

GATE2008Contd.

GATE 2003
Qualityscrewthreadsareproducedby (a) Threadmilling (b) Threadchasing (c) Threadcuttingwithsinglepointtool (d) Threadcasting

ThecorrectconnectionsandthecorrectplacementofUsare givenby (a) QandEareconnected. Us,isplacedbetweenPandQ. (b) SandEareconnected.Us isplacedbetweenRandS. (c) QandEareconnected.Us,isplacedbetweenQandE. (d) SandEareconnected.Us,isplacedbetweenSandE.

Page 3 of 69

10/31/2011

IES2010
For producing both internal and external screw threads, the method used is (a) Thread chasing with multiplerib chasers ( ) Thread milling g and multiple p thread cutters (b) (c) Thread tapping with taps (d) Die threading with selfopening die heads

IES2011
External threads can be produced by : 1. Rolling 2. Grinding 3 g 3. Milling (a) 1 and 3 only (b) 1 and 2 only (c) 2 and 3only (d) 1, 2 and 3

IES 2004
Match List I (Cutting tools) with List II (Features) and select the correct answer using the codes given below the Lists: List I List II A. A Turning T i tool t l 1. Chisel Chi l edge d B. Reamer 2. Flutes C. Milling cutter 3. Axial relief 4. Side relief Codes: A B C A B C (a) 1 2 3 (b) 4 3 2 (c) 4 2 3 (d) 1 3 2

GATE1994
To get good surface finish on a turned job, one should use a sharp tool with a ..feed and speed of rotation of the job. (a) ( ) Minimum, minimum (b) Minimum, maximum (c) Maximum, maximum (d) Maximum, minimum

IES 1996
Inturningofslenderrods,itisnecessarytokeep thetransverseforceminimummainlyto (a) Improvethesurfacefinish (b) Increaseproductivity (c) Improvecuttingefficiency (d) Reducevibrationsandchatter.

IES 2009
Whatisthenumberofjawsinselfcentred chuck? (a) Eight (b) Six (c) Four (d) Three

Page 4 of 69

10/31/2011

IES 1999
Which one of the following sets of forces are encountered by a lathe parting tool while groove cutting? (a) Tangential, radial and axial (b) Tangential T ti l and d radial di l (c) Tangential and axial (d) Radial and axial

IES 2009
Whichoneofthefollowingmethodsshouldbeused forturninginternaltaperonly? (a) Tailstockoffset (b) Taperattachment (c) Formtool (d) Compoundrest

IES 1998
A single short thread of pitch 2 mm is to be produced on a lathe having a lead screw with a double start thread of pitch 4 mm. The ratio of speeds between the spindle and lead screw for this operation is (a) 1 : 2 (b) 2: 1 (c) 1: 4 (d) 4: 1

IES 1993
It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If the spindle speed is 60 rpm, then the speed of the lead screw will be (a) 10 rpm (b) 20 rpm (c) 120 rpm (d) 180 rpm

IES 1992
Whichofthefollowingstatementisincorrectwith referenceoflathecuttingtools? (a) Theflankofthetoolisthesurfacebelowand adjacenttothecuttingedges (b) The Th noseis i the th corner,orchamfer h f joining j i i the th side id cuttingandtheendcuttingedges (c) Theheelisthatpartofthewhichisshapedto producethecuttingedgesandface (d) Thebaseisthatsurfaceoftheshankwhichagainst thesupportandtakestangent

IES 2006
It is required to cut screw threads with double start and 2 mm pitch on a lathe having lead screw pitch of 6 mm. What is the speed ratio between lathe spindle and lead screw? (a) 1 : 3 (b) 3: 1 (c) 2 : 3 (d) 3: 2

Page 5 of 69

10/31/2011

IES 1997
Consider the following operations: 1. Under cutting 2. Plain turning 3. Taper turning 4. Thread cutting The correct sequence of these operations in machining a product is (a) 2, 3, 4, 1 (b) 3, 2, 4, 1 (c) 2, 3, 1, 4 (d) 3, 2, 1, 4

IES 2009
A capstan lathe is used to massproduce, in batches of 200, a particular component. The direct material cost is Rs 4 per piece, the direct labour cost is Rs 3 per piece and the overhead costs are 400% of the labour costs. What is the production cost per piece? (a) Rs 19 (b) Rs 23 (c) Rs 16 (d) Rs 15

IES 2007
Assertion (A): In a multispindle automatic lathe, the turret tool holder is indexed to engage the cutting tools one by one for successive machining operations. Reason (R): Turret is a multiple tool holder so that for successive machining g operation, p , the tools need not be changed. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1995
Consider the following characteristics: 1. Multiple operations can be performed 2. Operator's fatigue is greatly reduced. 3. Ideally suited for batch production 4 A breakdown in one machine does not affect the 4. flow of products. 5. Can accommodate modifications in design of components, within certain limits. The characteristics which can be attributed to special purpose machines would include (a) 1, 3 and 4 (b) 1, 2 and 4 (c) 2, 3 and 5 (d) 1, 2 and 5

IES 1996
Assertion (A): Special purpose machine tools and automatic machine tools are quite useful for job shops Reason (R): Special purpose machine tools can do special types of machining work automatically (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 2003
Which one of the following mechanisms is employed for indexing of turret in an automatic lathe? (a) Whitworth (b) Rack and pinion ( ) Ratchet (c) R t h t and d pawl l (d) Geneva G wheel h l

Page 6 of 69

10/31/2011

IES 2009
For the manufacture of screw fasteners on a mass scale, which is the most suitable machine tool? (a) Capstan lathe (b) Singlespindle automatic lathe (c) CNC turning centre (lathe) (d) CNC machining centre

IES 2001
The indexing of the turret in a singlespindle automatic lathe is done using (a) Geneva mechanism (b) Ratchet and Pawl mechanism (c) Rack and pinion mechanism (d) Whitworth mechanism

IES 1995
Assertion (A): In a Swiss type automatic lathe, the turret is given longitudinal feed for each tool in a specific order with suitable indexing. Reason (R): A turret is a multiple tool holder to facilitate machining with each tool by indexing without the need to change the tools. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1992
Maximum production of small and slender parts is done by (a) Watch maker's lathe (b) Sliding head stock automatic lathe (c) Multispindle automatic lathe (d) Capstan lathe

IES 2007
Screw threads are produced on solid rods by using which of the following? (a) Dies (b) Punch (c) Mandrel (d) Boring bar

IAS 2007
Which one of the following is the characteristic for capstan lathe? (a) Rate of production is low (b) Labour cost is high (c) Used for handling jobs of varying shapes and sizes (d) Capstan head is mounted on a slide

Page 7 of 69

10/31/2011

IAS 2002
Consider the following statements related to Turret lathe: 1. Turret is mounted directly on the saddle. 2. Turret is mounted on an auxiliary slide. 3. Much heavier and larger jobs than Capstan lathe can be produced. Which of the above statements is/are correct? (a) 1 and 3 (b) 2 and 3 (c) 1 only (d) 2 only

IAS 1996
Apart from hexagonal turret, the elements (s) in a turret lathe include (s) (a) Crossslide tool post (b) Crossslide tool post and rear tool post (c) Crossslide tool post and tail stock (d) Teal tool post and tail stock

IAS 2004
Swiss type screw machines have (a) Turrets (b) Radial slides (c) Spindle carriers (d) Tool posts

IAS 2001
Consider the following operations and time required on a multi spindle automatic machine to produce a particular job 1. Turning 1.2 minutes 2. Drilling D illi 1.6 6 minutes i t 3. Forming 0.2 minute 4. Parting 0.6 minute The time required to make one piece (cycle time) will be (a) 0.6 minutes (b) 1.6 minutes (c) 3.6 minutes (d) 0.9 minute

IAS 1995
Assertion (A): In a multispindle automat, the turret is indexed to engage each of the cutting tool mounted on it. Reason(R): Turret is a multiple tool holder so that the machining can be continued with each tool without the need to change the tool. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IAS 1994
A multispindle automat performs four operations with times 50, 60, 65 and 75 seconds at each of its work centers. The cycle time (time required to manufacture one work piece) in seconds will be (a) 50 + 60 + 65 + 75 (b) (50 + 60 + 65 + 75) /4 (c) 75/4 (d) 75

Page 8 of 69

10/31/2011

IAS 1998
Assertion (A): For thread cutting, the spindle speed selected on a lathe, is very low. Reason (R): The required feed rate is low in threading operation. (a) and ( ) Both B th A and d R are individually i di id ll true t d R is i the th correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IAS 1998
Consider the following statements associated with the lathe accessories: 1. Steady rest is used for supporting a long job in between head stock and tail stock. 2. Mandrel M d l is i used d for f turning t i small ll cylindrical li d i l job. j b 3. Collects are used for turning discshaped job. Of these statements: (a) 1 and 2 are correct (b) 2 and 3 are correct (c) 3 alone is correct (d) 1 alone is correct

In Norton type feed gearbox for cutting Whitworth standard threads with a standard TPI Leadscrew, power flows from: (a) Spindle to Tumbler gear to Norton cone to Meander drive to Leadscrew (b) Spindle to Norton cone to Tumbler geat to Meander drive to Leadscrew (c) Spindle t o Tumbler gear to Meander drive to Norton cone to Leadscrew (d) Spindle to Norton cone to Meander drive to Tumbler gear to Leadscrew

IES2011

IAS 2000
Consider the following features: 1. All spindles operate simultaneously, 2. One piece is completed each time the tools are withdrawn and the spindles are indexed 3. The tool slide indexes or revolves with the spindle carrier Which of these features are characteristics of a multi spindle automatic machine used for bar work? (a) 1, 2 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1 and 3

Page 9 of 69

10/30/2011

Drilling

IES 2004
Consider the following statements: The helical flute in a twist drill provides the necessary 1. Clearance angle for the cutting edge 2. Rake angle for the cutting edge 3. Space for the chip to come out during drilling 4. Guidance for the drill to enter into the workpiece Which of the statements given above are correct? (a) 1 and 2 (b) 2 and 3 (c) 3 and 4 (d) 1 and 4

BySKMondal

IES 2003
The purpose of helical grooves in a twist drill is to 1. Improve the stiffness 2. Save a tool material 3. Provide space for chip removal 4. Provide rake angle for the cutting edge Select the correct answer using the codes given below: Codes: (a) 1 and 2 (b) 2 and 3 (c) 3 and 4 (d) 1 and 4

GATE 1996
The rake angle in a drill (a) Increases from centre to periphery (b) decreases from centre to periphery (c) Remains constant (d) Is irrelevant to the drilling operation

IES 1997
The rake angle in a twist drill (a) Varies from minimum near the dead centre to a maximum value at the periphery (b) Is maximum at the dead centre and zero at the periphery i h (c) Is constant at every point of the cutting edge (d) Is a function of the size of the chisel edge.

IES 1992
A drill for drilling deep holes in aluminum should have (a) High helix angle (b) Taper shank (c) Small point angle (d) No lip

Page 10 of 69

10/30/2011

GATE 1997
Helix angle of fast helix drill is normally (a) 35o (b) 60o (c) 90o (d) 5o

IES 1992
Low helix angle drills are preferred for drilling holes in (a) Plastics (b) Copper (c) Cast steel (d) Carbon steel

Example
A hole with 40mm diameter and 50mm depth is to be drilled in mild steel component. The cutting speed can be taken as 65 m/min and the feed rate as 0.25 mm/rev. Calculate the machining time and the material removal rate.

GATE 2002
The time taken to drill a hole through a 25 mm thick plate with the drill rotating at 300 r.p.m. and moving at a feed rate of 0.25 mm/revolution is (a) 10 sec (b) 20 sec (c) (d) 100 sec ( ) 60 6 sec

GATE 2004
Through holes of 10 mm diameter are to be drilled in a steel plate of 20 mm thickness. Drill spindle speed is 300 rpm, feed 0.2 mm/ rev and drill point angle is 120. Assuming drill over travel of 2 mm, the time for producing a hole will be (a) 4 seconds (b) 25 seconds (c) 100 seconds (d) 110 seconds

IES 2002
The arm of a radial drilling machine is being raised at a speed of 3.9 m/min by single start square threads of 6 mm pitch and 30 mm diameter. The speed of the screw (a) Is 650 rpm (b) Is 180 rpm (c) Is 130 rpm (d) Cannot be determined as the data is insufficient

Page 11 of 69

10/30/2011

IES 1994
The ratio between two consecutive spindle speeds for a sixspeed drilling machine using drills of diameter 6.25 to 25 mm size and at a cutting velocity of 18 m/min is (a) 1.02 1 02 (b) 1.32 1 32 (c) 1.62 (d) 1.82

IES 2009
What is the drilling time for producing a hole in an MS sheet of 25 mm thickness using an HSS drill of 20 mm diameter? The cutting speed and feed for drill are 20 m/min and 0.25 mm/revolution respectively, Neglect time taken for setting up, approaching and travelling of tools. (a) 0.314 min (b) 0.236 min (c) 0.438 min (d) 0.443 min

IES 2002
A 31.8 mm H.S.S. drill is used to drill a hole in a cast iron block 100 mm thick at a cutting speed 20 m/min and feed 0.3 mm/rev. If the over travel of drill is 4 mm and approach 9 mm, the time required to drill the hole is (a) 1 min 40 s (b) 1 min 44 s (c) 1 min 49 s (d) 1 min 53 s

IAS 1999
To drill a 10 mm diameter hole through a 20 mm thick M.S. plate with a drill bit running at 300 rpm and a feed of 0.25 mm per revolution, time taken will be (a) 8 s (b) 16 s (c) 24 s (d) 32 s

IAS 1994
The time (in minutes) for drilling a hole is given by

IES 1999
Match ListI (Drill bits) with ListII (Applications) and select the correct answer using the codes given below the Lists: ListI ListII A. Core drill 1. To enlarge a hole to a certain depth so as to accommodate the bolt head of a screw g an already y existing g hole in a B. Reamer 2. To drill and enlarge casting C. Counter bore drill 3. To drill a hole before making internal thread D. Tap drill 4. To improve the surface finish and dimensional accuracy of the already drilled hole Code:A B C D A B C D (a) 1 3 2 4 (b) 2 3 1 4 (c) 2 4 1 3 (d) 3 2 4 1

t=

where 'h' is the (a) Length of the drill (b) Drill diameter (c) Flute length of the drill (d) Cone height of the drill.

Depth of the hole + h Feed RPM

Page 12 of 69

10/31/2011

IES 1999

Reaming,Boring,Broaching

Which one of the following processes results in the best accuracy of the hole made? (a) Drilling (b) Reaming (c) Broaching (d) Boring

BySKMondal

IES 1999
Consider the following statements regarding reaming process: 1. Reaming generally produces a hole larger than its own diameter 2. Generally G ll rake k angles l are not t provided id d on reamers. 3. Even numbers of teeth are preferred in reamer design. Which of these statements are correct? (a) 1 and 2 (b) 2 and 3 (c) 1 and 3 (d) 1, 2 and 3

IES 1998
Match ListI with ListII and select the correct answer using the codes given below the lists: ListI ListII A. Reaming 1. Smoothing and squaring surface around the hole for proper seating B. Counterboring 2.Sizing and finishing the hole C. Countersinking 3. Enlarging the end of the hole D. Spot facing 4. Making a conical enlargement at the end of the hole Code:A B C D A B C D (a) 3 2 4 1 (b) 2 3 1 4 (c) 3 2 1 4 (d) 2 3 4 1

IES 1994
In reaming process (a) Metal removal rate is high (b) High surface finish is obtained. (c) High form accuracy is obtained (d) High dimensional accuracy is obtained.

IES 1993
A hole of 30 mm diameter is to be produced by reaming. The minimum diameter permissible is 30.00 mm while the maximum diameter permissible is 30.05 mm. In this regard, consider the following statements about the reamer size:
1. The minimum diameter of the reamer can be less than 30 mm. 2. The minimum diameter of the reamer cannot be less than 30 mm. 3. The maximum diameter of the reamer can be more than 30.05 mm. 4.The maximum diameter of the reamer must be less than 30.05 mm.

Of these statements (a) 1 and 4 are correct (c) 2 and 3 are correct

(b) (d)

1 and 3 are correct 2 and 4 are correct

Page 13 of 69

10/31/2011

IES 1998
A component requires a hole which must be within the two limits of 25.03 and 25.04 mm diameter. Which of the following statements about the reamer size are correct? 1. 1 Reamer size cannot be below 25.03 25 03 mm. mm 2. Reamer size cannot be above 25.04 mm. 3. Reamer size can be 25.04 mm. 4. Reamer size can be 25.03 mm. Select the correct answer using the codes given below: (a) 1 and 3 (b) 1 and 2 (c) 3 and 4 (d) 2 and 4

IAS 1999
For reaming operation of blind hole, the type of reamer required is (a) Straight flute reamer (b) Right hand spiral fluted reamer (c) Left hand spiral fluted reamer (d) None of the above

IAS 2003
Match List I (Operation) with List II (Application) and select the correct answer using the codes given below the lists: ListI ListII (Operation) (Application) (A) Reaming 1. Used for enlarging the end of a hole to give it a conical i l shape h for f a short h distance di (B) Boring 2. Used for enlarging only a limited portion of the hole (C) Counter boring 3. Used for finishing a hole (D) Counter sinking 4. Used for enlarging a hole Codes:A B C D A B C D (a) 3 2 4 1 (b) 1 4 2 3 (c) 3 4 2 1 (d) 1 2 4 3

IES 1992
Shell reamers are mounted on (a) Tool holders (b) Amour plates (c) Arbor (d) Shanks

IES 1993
The main purpose of boring operation, as compared to drilling is to: (a) Drill a hole (b) Finish the drilled hole (c) Correct the hole (d) Enlarge the existing hole

IES 1994
Enlarging an existing circular hole with a rotating single point tool is called (a) Boring (b) Drilling (c) Reaming (d) Internal turning.

Page 14 of 69

10/31/2011

IES 1992
Which of the machine tools can be used for boring 1. Lathe 2. Drilling machine 3. Vertical milling machine 4. Horizontal milling machine (a) 1, 2, 3 (b) 1, 3, 4 (c) 2 and 4 (d) 1, 2, 3, 4

IES 2000
Which one of the following sets of tools or tools and processes are normally employed for making large diameter holes? (a) Boring tool (b) BTA tools t l (Boring (B i and d trepanning t i association) i ti ) and d gun drill (c) Gun drill and boring tool (d) Boring tools and trepanning

IES 1996
Which of the following statements are correct? 1. A boring machine is suitable for a job shop. 2. A jig boring machine is designed specially for doing more accurate work when compared to a vertical milling illi machine. hi 3. A vertical precision boring machine is suitable for boring holes in cylinder blocks and liners. (a) 1, 2 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1 and 3.

IES 1995
The effects of setting a boring tool above centre height leads to a/an. (a) Increase in the effective rake angle and a decrease in the effective clearance angle. (b) Increase I i both in b th effective ff ti rake k angle l and d effective ff ti clearance angle. (c) Decrease in the effective rake angle and an increase in the effective clearance angle. (d) Decrease in both effective rank angle and effective clearance angle.

JWM2010
Considerthefollowingoperationsregardingboring machines: 1.Counterboring 2.Countersinking 3.Trepanning Whichoftheaboveoperationsis/arecorrect? (a)1,2and3 (b)1and2only (c)2and3only (d)1only

IES 2007
Among the following machining processes, which can be used for machining flat surfaces? 1. Shaping 2. Milling 3. Broaching Select the correct answer using the code given below: (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Page 15 of 69

10/31/2011

IES 1993
Assertion (A): Soluble oils are employed with broaching machine. Reason (R): Soluble oils have excellent cooling effect. (a) and ( ) Both B th A and d R are individually i di id ll true t d R is i the th correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1993,2001
Assertion (A): No separate feed motion is required during broaching. Reason (R): The broaching machines are generally hydraulically operated. (a) and ( ) Both B th A and d R are individually i di id ll true t d R is i the th correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 2001
The screw and nut in a broaching machine are changed from square thread to ACME thread. The power requirement of the machine at the same r.p.m. will (a) Remain same (b) Decrease (c) Increase (d) Depend on the operator

IAS 2004
Which one of the following is true for the last few teeth of a broach which are meant for fine finishing? (a) They have equal diameter (b) They Th have h i increasing i diameter di t (c) They have decreasing diameter (d) They have alternately increasing and decreasing diameter.

IES 2005
Match List I (Tool) with List II (Element of Tool) and select the correct answer using the code given below the Lists: List I List II A Broach 1. Tang B. Reamer 2. Pilot C. Drill 3. Front taper D. Carbide insert face mill 4. Bond 5. Sweeper tooth Codes:A B C D A B C D (a) 2 5 1 3 (b) 1 3 4 5 (c) 2 3 1 5 (d) 1 5 4 3

IES 2002
Match List I with List II and select the correct answer: List I (Machine tool) List II (Features) A. Lathe 1. Push or pull tool B. Drilling machine 2. Rachet and pawl mechanism C. Shaper 3. Dividing head D. Broaching machine 4. Hollow tapered spindle 5. Face plate Codes:A B C D A B C D (a) 2 4 5 1 (b) 5 3 2 4 (c) 2 3 5 4 (d) 5 4 2 1

Page 16 of 69

10/31/2011

Milling

Example
AC50steelflatsurfaceofdimensions100mm 250 mmistobeproducedonahorizontalaxismilling machine.AnHSSslabmillwitha100mmdiameter and150mmwidthistobeusedforthepurpose.The millingcutterhas8teeth. Calculatethemachiningtimeassumingthatentire stockcanberemovedinonedepthof2mm. Given, Feed,f=0.13mm/tooth, Cuttingspeed,V=20m/min.

BySKMondal

GATE 1995
ListI (Manufacturing Processes) (A) Finish turning 1. (B) Forming 2. (C) Thread cutting 3. (D) Down milling 4. Codes:A B C D (a) 2 3 4 1 (b) (c) 1 2 3 4 (d) List II (Condition) Backlash eliminator Zero rake Nose radius Low speed A B C D 3 4 1 2 4 1 2 3

GATE 1993
A milling cutter having 8 teeth is rotating at 150 rpm. If the feed per tooth is 0.1, the table speed in mm per minute is (a) 120 (b) 187 ( ) 125 (d) 70 (c)

IES 2003
In milling machine, the cutting tool is held in position by (a) Chuck (b) Spindle (c) Arbor (d) Tool holder

IES 2009
The arbor of a milling machine is used to hold which one of the following? (a) Spindle (b) Overarm (c) Cutting tool (d) Mandrel

Page 17 of 69

10/31/2011

IES 1994
Consider the following operations: 1. Cutting key ways on shafts 2. Cutting external screw threads. 3. Cutting teeth of spur gears 4. Cutting external splines. Those which can be performed with milling cutters would include (a) 1 and 2 (b) 2,3 and 4 (c) 1 and 3 (d) 1,2,3 and 4 .

IES 1992
A set of eight form relieved milling cutters for each module is provided to enable cutting of gears of different (a) Materials (b) Types e.g. spur, helical, T h li l etc. t (c) Number of teeth (d) Width of gears

IES 2007
What is the process of removing metal by a milling cutter which is rotated against the direction of travel of the work piece, called? (a) Down milling (b) Up milling (c) ( ) End E d milling illi (d) Face F milling illi

GATE 1992
In horizontal milling process. (up/down) milling provides better surface finish and.. (updown) milling provides longer tool life.

IES 1997
Consider the following statements: In Up milling process, 1. The cutter starts the cut from the machined surface and proceeds upwards. 2. The cutter starts the cut from the top p surface and proceeds downwards. 3. The job is fed in a direction opposite to that of cutter rotation. 4. The job is fed in the same direction as that of cutter rotation. Of these statements correct are: (a) 1 and 3 (b) 1 and 4 (c) 2 and 3 (d) 2 and 4

IES 1995
Assertion (A): Up milling or climb milling is commonly used for machining castings and forgings. Reason (R): Up milling can be done on universal milling machines. machines (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Page 18 of 69

10/31/2011

IES 2005
Which one of the following statements is correct? In upmilling operation, the undeformed chip thickness, a) Is zero at the start of the cut and increases to a maximum value just before the tooth disengages the workpiece. k i b) Increases to the maximum value at the centre of the travel and decreases towards the end of tooth engagement. c) Has a maximum value just after the cut is started and drops to zero at the end of the cut. d) Remains unchanged.

IES 1993
Climb milling is chosen while machining because (a) The chip thickness increases gradually (b) It enables the cutter to dig in and depth of cut (c) The specific power consumption is reduced (d) Better surface finish can be obtained

IES2010
Assertion (A): Climb or down milling operation ensures smoother operation of the machine tool and longer tool life as compared to the conventional up milling operation. Reason (R): In climb or down milling operation, the rotational motion of the cutter as well as the feed motion of the workpiece are in the same direction, direction and the depth of cut is maximum at the entry point as the cutter engages the workpiece. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 2002
Assertion (A): Virtually all modern milling machines are capable of doing downmilling. Reason (R): In downmilling the cutter tends to push the work along and lift it upward from the table. This action tends to eliminate any effect in looseness in the feed screw and nut of the milling machine table and results in smooth cut. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 2004
The cutting speed of a milling cutter while cutting brass is: (a) 45 to 60 m/min (b) 30 to 40 m/min (c) 25 to 35 m/min (d) 15 to 20 m/min

IES 2006
Gang milling is a (a) Milling process for generating hexagonal surfaces (b) Process of cutting gears (c) Process in which two or more cutters are used simultaneously (d) Milling operation combined with turning

Page 19 of 69

10/31/2011

IES 2009
For machining, which one of the following gang milling operations is employed? (a) Threads (b) Bores (c) Grooves (d) Steps on prismatic parts

IES 1995
In a milling operation two side milling cutters are mounted with a desired distance between them so that both sides of a work piece can be milled simultaneously. This set up is called. (a) Gang milling (b) Straddle milling (c) String milling (d) Side milling.

IES 2004
One brand of milling machine has the following two index plates supplied along with the indexing head: Plate 1: 15, 16, 17, 18, 19, 20 hole circles Plate 2: 21, 23, 27, 29, 31, 33 hole circles It is proposed to mill a spur gear of 28 teeth using simple indexing method. Which one of the following combinations of index plate and number of revolutions is correct? (a) Plate 1: 1 revolution and 9 holes in 18 hole circles (b) Plate 2: 1 revolution and 9 holes in 21 hole circles (c) Plate 2: 1 revolution and 9 holes In 33 hole circles (d) Plate 1: 1 revolution and 9 holes In 15 hole circles

IES 2000
One of the index plates of a milling machine dividing head has the following hole circles: 15; 16; 17; 18; 19; 20 A gear wheel of 34 teeth has to be milled by simple indexing method. method To machine each tooth, tooth the index crank has to be rotated through (a) 17 holes in the 20hole circle (b) 18 holes in the 20hole circle (c) 1 revolution and 3 holes in 17hole circle (d) 1 revolution and 2 holes in 18hole circle

IES 1999
A straight teeth slab milling cutter of 100 mm diameter and 10 teeth rotating at 200 r.p.m. is used to remove a layer of 3 mm thickness from a steel bar. If the table feed is 400 mm/minute, the feed per tooth in this operation will be (a) 0.2 mm (b) 0.4 mm (c) 0.5 mm (d) 0.6 mm

IES 2002
A side and face cutter 125 mm diameter has 10 teeth. It operates at a cutting speed of 14 m/min with a table traverse 100 mm/min. The feed per tooth of the cutter is (a) 10 mm (b) 2.86 2 86 mm (c) 0.286 mm (d) 0.8 mm

Page 20 of 69

10/31/2011

IES 2004
Match List I (Milling problem) with List II (Probable causes) and select the correct answer using the codes given below the Lists: List I List II A. Chatter 1. Too high feed B. Poor surface finish 2. Lack of rigidity in machine fixtures, bar or workpiece C. Loss of accuracy 3. High cutting load D. Cutter burrs 4. Radial relief too great 5. Not enough lubricant Codes:A B C D A B C D (a) 2 1 5 3 (b) 2 1 3 5 (c) 4 5 2 3 (d) 4 2 3 5

IAS 2001
Which one of the following statements are correct in respect of upmilling and downmilling? 1. In upmilling the cutter rotates in a direction opposite to that of workpiece travel whereas in downmilling the cutter rotates in a direction similar to that of workpiece travel. 2. In downmilling chip will be thin at the beginning and increase to a p maximum at the end of the cut and reverse will be the case for a chip formed f d by b upmilling. ll 3. Downmilling is desirable with milling cutters having a high radial rake angle when compared to upmilling. 4. Downmilling forces the workpiece against the milling table to exert more pressure while upmilling tends to lift the workpiece from the table. Select the correct answer using the codes given below: Codes: (a) 1, 2 and 3 (b) 1, 2 and 4 (c) 3 and 4 (d) 1, 3 and 4

IAS 1998
Which of the following statements are true of face milling? 1. Face milling cutter is held on an arbor. 2. It has two rake angles axial rake and radial rake. 3. 3 The maximum chip thickness equals the feed per tooth. 4. The chip thickness varies from a minimum at the start of cut to a maximum at the end of cut. Select the correct answer using the codes given below: Codes : (a) 1 and 2 (b) 2 and 3 (c) 2 and 4 (d) 3 and 4

IAS 2001
Which of the following mechanisms are suitable for indexing the table of rotary transfer line? 1. Rack and pinion 2. Ratchet and pawl 3. Lead screw 4. Geneva mechanism Select the correct answer by using the codes given below: Codes: (a) 1, 2 and 3 (b) 2, 3 and 4 (c) 1, 3 and 4 (d) 1, 2 and 4

IAS 2000
Consider the following mechanisms: 1. Geneva gearing 2. Rack and pinion 3. Ratchet and pawl Which of these mechanisms are used to index the work table on a transfer machine? (a) 1 and 2 (b) 2 and 3 (c) 1 and 3 (d) 1, 2 and 3

IAS 1994
A standard dividing head is equipped with the following index plates 1. Plate with 12, 16, 17, 18, 19, 20 holes circles 2. Plate with 21, 23, 27, 29, 31, 33 holes circles 3. Plate with 37, 39, 41,43,47,49 holes circles For obtaining 24 divisions on a work piece by simple indexing (a) Hole plate 2 alone can be used (b) Hole plates 1 and 2 can be used (c) Hole plates 1 and 3 can be used (d) Any of the three hole plates can be used

Page 21 of 69

10/31/2011

IAS 2003
A milling cutter of 70 mm diameter with 12 teeth is operating at a cutting speed of 22 m/min and a feed of 0.05 mm/tooth. The feed per minute is (a) 110 m/min (b) 35 mm/min (c) ( ) 6 mm/min / i (d) 60 6 mm/min / i

IES1994
Whichoneofthefollowingoperationsiscarriedout attheminimumcuttingvelocityifthemachinesare equallyrigidandthetoolworkmaterialsarethe same? (a) Turning (b) Grinding (c) Boring (d) Milling

IES2011
MatchListIwithListIIandselectthecorrectanswerusing thecodegivenbelowthelists:

IES 2002
Match List I with List answer: List I (Machine tools) A. Lathe B. Milling machine C. Shaper D. Drilling machine Codes:A B C D (a) 4 2 3 1 (c) 4 3 2 1 II and select the correct List II (Machine tool parts) 1. Lead strew 2. Rocker arm 3. Universal indexing 4. Flute A B C D (b) 1 3 2 4 (d) 1 2 3 4

ListI A.Lathe B.Shaper C.Drillingmachine D. Millingmachine Codes

ListII 1.Flute 2.Universalindexing 3.Leadscrew 4.Rockerarm

Ch7:Milling
QNo 1 2 3 4 5 6 Option B B D A C D Q.No 7 8 9 10 11 12 Option D D A D C D

Page 22 of 69

10/31/2011

GATE 2005
A 600 mm x 30 mm flat surface of a plate is to be finish machined on a shaper. The plate has been fixed with the 600 mm side along the tool travel direction. If the tool overtravel at each end of the plate is 20 mm, average cutting speed is 8 m/min, feed rate is 0.3 mm/stroke and the ratio of return time to cutting time of the tool is 1:2, the time required for machining will be (a) 8 minutes (b) 12 minutes (c) 16 minutes (d) 20 minutes

Shaper,Planner,Slotter
BySKMondal

IES 2004
Consider the following alignment tests on machine tools 1. Straightness 2. Flatness 3. Run out 4. Parallelism Which of the above alignment tests on machine tools are common to both lathe and shaper? (a) 1 and 2 (b) 2 and 3 (c) 3 and 4 (d) 1 and 4

IES 2001
In a shaper machine, the mechanism for tool feed is (a) Geneva mechanism (b) Whitworth mechanism (c) Ratchet and Pawl mechanism (d) Ward Leonard system

IES2010
Assertion (A): Longitudinal cutting motion of the tool and crosswise feed motion of the job generates flat surfaces in planning process. Reason (R): Jobs used in planning machines are generally long and heavy compared to shaping. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1997
Which of the following are the advantages of a hydraulic shaper over a mechanically driven shaper? 1. More strokes per minute can be obtained at a given cutting speed. 2. The Th cutting tti stroke t k has h a definite d fi it stopping t i point. i t 3. It is simpler in construction. 4. Cutting speed is constant throughout most of the cutting stroke. Select the correct answer using the codes given below: (a) 1 and 2 (b) 1 and 4 (c) 2 and 4 (d) 1, 3 and 4

Page 23 of 69

10/31/2011

IES 1995
In a mechanical shaper, the length of stroke is increased by (a) Increasing the centre distance of bull gear and crank pin (b) Decreasing the of D i th centre t distance di t f bull b ll gear and d crank pin (c) Increasing the length of the ram (d) Decreasing the length of the slot in the slotted lever

IES 1994
Given that, average cutting speed = 9 m/min, the return time to cutting time ratio is = 1 : 2, the feed rate = 0.3 mm/stroke, the clearance at each end of cut = 25 mm and that the plate is fixed with 700 mm side along the direction of tool travel, the time required for finishing one flat surface of a plate of size 700 x 30 mm in a shaper, will be (a) 10 min (b) 12.5 min (c) 15 min (d) 20 min

IAS 1995
Size of a shaper is given by (a) Stroke length (c) Weight of the machine (b) (d) Motor power Table size.

IAS 1994
Stroke of a shaping machine is 250 mm. It makes 30 double strokes per minute. Overall average speed of operation is (a) 3.75 m/min (b) 5.0 m/min ( ) 7.5 m/min (c) / i (d) 15 m/min / i

Page 24 of 69

10/31/2011

IES 1999

GearManufacturing

BySKMondal

Consider the following processes for the manufacture of gears: 1. Casting 2. Powder metallurgy 3. Machining from bar stock 4. Closed die forging The correct sequence in increasing order of bending strength of gear teeth is (a) 1, 2, 3, 4 (b) 1, 2, 4, 3 (c) 2, 1, 4, 3 (d) 2, 1, 3, 4

IES 2006
Which of the following is/are used for cutting internal gears? 1. Gear hobber 2. Gear shaper 3. Rack cutter 4. Jig borer Select the correct answer using the codes given below: (a) Only 1 and 2 (b) Only 2 and 3 (c) Only 1 and 4 (d) Only 2

IES 2005
In helical milling, the ratio of the circumference of the gear blank to the lead of the helix determines the: (a) Proper speed to use (b) Proper P f d and feed d depth d th of f cut t required i d (c) Angle setting of the machine table (d) Gear ratio for table screw and dividing head

IES2010
Match List I with List II and select the correct answer using the code given below the lists: List I List II (Type of work) (Manufacturing) A. High rate production of worm Gears and 1. Gear shaving worm wheel B. Generating internal gears and Cluster gears 2. Gear milling C. Finishing of gear tooth profiles 3. Gear hobbing D. Repair and piece production of gears 4. Gear shaping A B C D A B C D (a) 2 1 4 3 (b) 3 1 4 2 (c) 2 4 1 3 (d) 3 4 1 2

IES 1996
Gear cutting on a milling machine using an involute profile cutter is a (a) Gear forming process (b) Gear generating process. (c) Gear shaping process (d) Highly accurate gear producing process.

Page 25 of 69

10/31/2011

IES 2000
Which one of the following processes of gear manufacture results in best accuracy of the involute gear tooth profile? (a) Milling (b) Hobbing H bbi (c) Rotary gear shaper (d) Rack type gear shaper

IES 2009
Assertion (A): Gears produced by employing form cutting principle using gearmilling cutter on a milling machine are not very accurate. Reason (R): Production of the correct gear tooth profile employing formcutting principle would require a separate cutter for cutting different numbers of teeth even for the same module and also errors are associated with inaccurate operation of indexing mechanism. (a) Both A and R are true and R is the correct explanation of A (b) Both A and R are true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1996
Consider the following processes of gear manufacture: 1. Milling with form cutter 2. Rack type gear shaper (gear planer) 3. Rotary gear shaper (gear shaper) 4. Gear hobbing The correct sequence of these processes in increasing order of accuracy of involute profile of the gear (a) 3, 2, 4, 1 (b) 2, 3, 4, 1 (c) 3, 2, 1, 4 (d) 2, 3, 1, 4

IES 2009
By which one of the following machines the teeth of an internal spur gear can be cut accurately? (a) Milling machine (b) Slotting machine (c) Hobbing machine (d) Gearshaping machine

IES 2004
Gear shaping is a process of manufacturing gears. Which one of the following principles is employed by it? (a) Form cutting with cutter (b) Generating tooth form with a reciprocating cutter (c) Generating tooth form by a rotating cutter (d) Generating form with a reciprocating and revolving cutter

IES 1992
In gear hobbing (a) Only hob rotates (b) Only gear blank rotates (c) Both hob and gear blank rotate (d) Neither hob nor gear blank rotates

Page 26 of 69

10/31/2011

IES 2003
A spur gear of 40 teeth is machined in a gear hobbing machine using a double start hob cutter. The speed ratio between the hob and the blank is (a) 1:20 (b) 1:40 (c) ( ) 40: 1 (d) 20: 1

IES 2008
Which machining processes are used for gear manufacture? 1. Form milling 2. Broaching 3. Roll forming 4. Hobbing Select the correct answer using the code given below: (a) 1, 2 and 3 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 2, 3 and 4

IES 1999
A 60teeth gear when hobbed on a differential hobber with a twostart hob, the index change gear ratio is governed by which one of the following kinematic balance equations? (a) 1 revolution of gear blank = 1/60 of hob revolutions (b) 1 revolution of gear blank = 2/60 of hob revolutions (c) 1 revolution of hob = 2/60 of blank revolutions (d) 1 revolution of hob = 1/60 of blank revolutions

IES 1997
Which of the following motions are not needed for spur gear cutting with a hob? 1. Rotary motion of hob 2. Linear axial reciprocator motion of hob 3. Rotary motion of gear blank 4. Radial advancement of hob. Select the correct answer using the codes given below: (a) 1, 2 and 3 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 2, 3 and 4

IES 2007
Which of the following methods are gear generating processes? 1. Gear shaping 2. Gear hobbing 3. Gear milling Select the correct answer using the code given below: (a) 1, 2 and 3 (b) 1 and 2 only (c) 2 and 3 only (d) 1 and 3 only

IES 1993
Internal gear cutting operation can be performed by (a) Milling (b) Shaping with rack cutter (c) Shaping with pinion cutter (d) Hobbing

Page 27 of 69

10/31/2011

IAS 1998
Assertion (A): Internal gears are cut on a gear shaper. Reason (R): Hobbing is not suitable for cutting internal gear. (a) and ( ) Both B th A and d R are individually i di id ll true t d R is i the th correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 2006
Which of the following cannot be cut by hobbing process? (a) Helical gears (b) Bevel gears (c) Worm gears (d) Spur gears

IES 1996
For the manufacture of full depth spur gear by hobbing process, the number of teeth to be cut = 30, module = 3 mm and pressure angle = 20. The radial depth of cut to be employed should be equal to (a) 3.75 3 75 mm (b) 4.50 4 50 mm (c) 6.00 mm (d) 6.75 mm

IES 1995
While cutting helical gears on a nondifferential gear hobber, the feed change gear ratio is (a) Independent of index change gear ratio (b) dependent on speed change gear ratio (c) Interrelated to index change gear ratio (d) Independent of speed and index change gear ratio.

IES 1992
Gear burnishing process for (a) Removing residual stresses from teeth roots (b) Surface finishing (c) Undercut gears (d) Cycloidal gears

IAS 2003
Which one of the following is not a feature of gear hobbing process? (a) High rate of production (b) Generation of helical gears (c) Very accurate tooth profile (d) Generation of internal gears

Page 28 of 69

10/31/2011

IAS 2001
Consider the following motions and setting in a hobbing machine: 1. Hob rotation 2. Job rotation 3. Axial reciprocating hob rotation 4. Tilting of hob to its helix angle Which of these motions and setting in a hobbing machine are required to machine a spur gear? (a) 1, 2 and 3 (b) 2, 3 and 4 (c) 1, 2 and 4 (d) 1, 3 and 4

IES 1994
Consider the following machine tools: 1. Hobbing machine 2. Gear shaping machine 3. Broaching machine. The teeth of internal spur gears can be cut in (a) 1, 2 and 3 (b) 1 and 2 (c) 1and 3 (d) 2 and 3

Page 29 of 69

10/31/2011

GATE 1995
Among the conventional machining processes, maximum specific energy is consumed in (a) Turning (b) Drilling (c) Planning (d) Grinding

Grinding&Finishing
BySKMondal

GATE 1998
Ideal surface roughness, as measured by the maximum height of unevenness, is best achieved when, the material is removed by (a) An end mill (b) A grinding i di wheel h l (c) A tool with zero nose radius (d) A ball mill.

GATE 1998
In machining using abrasive material, increasing abrasive grain size (a) Increases the material removal rate (b) Decreases the material removal rate (c) First decreases and then increases the material removal rate (d) First increases and then decreases the material removal rate

GATE 2000
Abrasive material used in grinding wheel selected for grinding ferrous alloys is (a) Silicon carbide (b) Diamond (c) Aluminium oxide (d) Boron carbide

GATE 2002
The hardness of a grinding wheel is determined by the (a) Hardness of abrasive grains (b) Ability of the bond to retain abrasives (c) Hardness of the bond (d) Ability of the grinding wheel to penetrate the work piece

Page 30 of 69

10/31/2011

GATE 2004
Typical machining operations are to be performed on hard tomachine materials by using the processes listed below. Choose the best set of OperationProcess combinations Operation Process P. Debarring (internal surface) 1. Plasma Arc Machining Q. 2. Abrasive Flow Machining Q Die sinking 2 R. Fine hole drilling in thin sheets 3. Electric Discharge Machining S. Tool sharpening 4. Ultrasonic Machining 5. Laser beam Machining 6. Electrochemical Grinding (a) P1 Q5 R3 S4 (b) P1 Q4 R1 S2 (c) P5 Q1 R2 S6 (d) P2 Q3 R5 S6

GATE 2006
If each abrasive grain is viewed as a cutting tool, then which of the following represents the cutting parameters in common grinding operations? (a) Large negative rake angle, low shear angle and high cutting speed (b) Large positive rake angle, low shear angle and high cutting speed (c) Large negative rake angle, high shear angle and low cutting speed (d) Zero rake angle, high shear angle and high cutting speed

GATE 1997
List I (A) Grinding (B) Honing 1. 2. List II Surface for oil retention Surface for max. load capacity Surface of limiting friction Surface of matte finish Surface for pressure sealing Surface for interference fit.

IES 2005
Consider the following statements in respect of grinding? 1. The pitch of the grit cutting edges is larger than the pitch of the milling cutter. 2. The Th cutting tti angles l of f the th grits it have h a random d geometry. 3. The size of the chip cuts is very small for grinding. Which of the statements given above are correct? (a) 1 and 2 (b) 2 and 3 (c) 1 and 3 (d) 1, 2 and 3

(C) Superfinishing 3. D) Burnishing 4. 5. 6.

IES 2009
Which one of the following is NOT used as abrasive material in grinding wheels? (a) Aluminium oxide (b) Silicon carbide (c) Cubic boron nitride (d) Manganese oxide

IES 1997
Which one of the following materials is used as the bonding material for grinding wheels? (a) Silicon carbide (b) Sodium silicate (c) Boron carbide (d) Aluminum oxide

Page 31 of 69

10/31/2011

IES 1996
Grinding wheel is said to be loaded when the (a) Metal particles get embedded in the wheel surface blocking the interspaces between cutting grains. (b) Bonding material comes on the surface and the wheel blunt. h l becomes b bl t (c) Work piece being ground comes to a stop in cylindrical grinding. (d) Grinding wheel stops because of very large depth of cut

IES 2001
Specific cutting energy is more in grinding process compared to turning because (a) Grinding (cutting) speed is higher (b) The wheel has multiple cutting edges (grains) (c) Plaguing force is significant due to small chip size (d) Grinding wheel undergoes continuous wear

IES 1996
Specific energy requirements in a grinding process are more than those in turning for the same metal removal rate because of the (a) Specific pressures between wheel and work being high. high (b) Size effect of the larger contact areas between wheel and work. (c) High cutting velocities (d) High heat produced during grinding.

IES 1994
The ratio of thrust force to cutting force is nearly 2.5 in (a) Turning (b) Broaching (c) Grinding (d) Plain milling

IES 1992
Assertion (A): Vitrified bond is preferred for thin grinding wheels. Reason (R): Vitrified bond is hard brittle. (a) Both A and R are individually true and R is the correct t explanation l ti of fA (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 2000
Assertion (A): The ratio of cutting force to thrust force is very high in grinding process as compared to other machining processes. Reason (R): Random orientation and effective negative rake angles of abrasive grains increase the cutting force and adversely affect the cutting action and promote rubbing action. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Page 32 of 69

10/31/2011

IES 1995
Soft materials cannot be economically grind due to (a) The high temperatures involved (b) Frequent wheel clogging (c) Rapid wheel wear (d) Low work piece stiffness

IES2010
In relation to the peripheral or surface speeds of the grinding wheel and that of the workpiece in cylindrical grinding of alloy steel workpieces, the grinding wheel speed is (a) Less than the speed of the workpiece (b) Same as the speed of the workpiece (c) Double the speed of the workpiece (d) 65 to 75 times the speed of the workpiece.

IES 2009
Given that the peripheral speed of the grinding wheel of 100 mm diameter for cylindrical grinding of a steel work piece is 30 m/s, what will be the estimated rotational speed of the grinding wheel in revolution per minute (r.p.m.)? (a) 11460 (b) 5730 (c) 2865 (d) 95

IES 2002
Which of the following materials are used in grinding wheel? 1. Aluminium oxide 2. Cubic boron nitride 3. Silicon carbide Select the correct answer using the codes given below: (a) 1, 2 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1 and 3

IES 2001
The marking on a grinding wheel is '51 A 36 L 5 V 93'. The code '36' represents the (a) Structure (b) Grade (c) Grain size (d) Manufacturer's number

IES 2000
The sequence of markings "S 14 K 14 S" on a grinding wheel represents respectively (a) Bond type, structure, grade, grain size and abrasive type (b) Abrasive Ab i type, t grain i size, i grade, d structure t t and d bond b d type (c) Bond type, grade, structure, grain size and abrasive type (d) Abrasive type, structure, grade, grain size and bond type

Page 33 of 69

10/31/2011

IES 1995
In the grinding wheel of A 60 G 7 B 23, B stands for (a) Resinoid bond (b) Rubber bond (c) Shellac bond (d) Silicate bond.

IES 1993
Tool life in the case of a grinding wheel is the time (a) Between two successive regrinds of the wheel (b) Taken for the wheel to be balanced (c) Taken between two successive wheel dressings (d) Taken for a wear of 1mm on its diameter

IES 2001
Assertion (A): Hard wheels are chosen for grinding hard metals. Reason (R): In hard wheels only the abrasive grains are retained for long time. (a) ( ) Both B th A and d R are individually i di id ll true t and d R is i the th correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1994
Consider the following statements regarding grinding of high carbon steel: 1. Grinding at high speed results in the reduction of chip thickness and cutting forces per grit. 2. Aluminium Al i i oxide id wheels h l are employed. l d 3. The grinding wheel has to be of open structure. Of these statements (a) 1, 2 and 3 are correct (b) 1 and 2 are correct (c) 1 and 3 are correct (d) 2 and 3 are correct

IES 1999
Consider the following reasons: 1. Grinding wheel is soft 2. RPM of grinding wheel is too low 3. Cut is very fine 4. An improper cutting fluid is used A grinding wheel may become loaded due to reasons stated at (a) 1 and 4 (b) 1 and 3 (c) 2 and 4 (d) 2 and 3

IES 2001
Dry and compressed air is used as cutting fluid for machining (a) Steel (b) Aluminium (c) Cast iron (d) Brass

Page 34 of 69

10/31/2011

IES 2000
Consider the following statements: In electrochemical grinding, 1. A rubber bonded alumina grinding wheel acts as the cathode and the workplace as the anode. 2. 2 A copper bonded alumina grinding wheel acts as the cathode and the work piece as the anode. 3. Metal removal takes place due to the pressure applied by the grinding wheel. 4. Metal removal takes place due to electrolysis. Which of these statements are correct? (a) 1 and 3 (b) 2 and 4 (c) 2 and 3 (d) 1 and3

IES 1993
In centre less grinding, the work piece centre will be (a) Above the line joining the two wheel centres (b) Below the line joining the two wheel centres (c) On the line joining the two wheel centres (d) At the intersection of the line joining the wheel centres with the work plate plane.

IES 2000
Consider the following advantages: 1. Rapid process 2. Work with keyways can be ground 3. No work holding device is required. Which of these are the advantages of centre less grinding? (a) 1, 2 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1 and 3

IES 1999
Match ListI with ListII and select the correct answer using the codes given below the Lists: ListI ListII A. Die sinking 1. Abrasive jet machining B. Debarring g 2. Laser beam machining g C. Fine hole drilling (thin materials) 3. EDM D. Cutting/sharpening hard materials 4. Ultrasonic machining 5. Electrochemical grinding Code:A B C D A B C D (a) 3 5 4 1 (b) 2 4 1 3 (c) 3 1 2 5 (d) 4 5 1 3

IES 1996
A grinding wheel of 150 mm diameter is rotating at 3000 rpm. The grinding speed is

IES 1993
Consider the following parameters: 1. Grinding wheel diameter. 2. Regulating wheel diameter. 3. Speed of the grinding wheel. 4. Speed of the regulating wheel. 5. Angle between the axes of grinding and regulating wheels. Among these parameters, those which influence the axial feed rate in centreless grinding would include (a) 2, 4 and 5 (b) 1, 2 and 3 (c) 1, 4 and 5 (d) 3, 4 and 5

Page 35 of 69

10/31/2011

IES 2007
Honing Process gives surface finish of what order? (a) 10 m (CLA) (b) 1.0 m (CLA) (c) 0.1 m (CLA) (d) 0.01 m (CLA)

IES 1992
CLA value for Honing process is (a) 6 (b) 0.05 3.0 (c) 0.05 1.0 (d) 0.025 0.1

IES 2001
Match ListI (Cutting Tools) with ListII (Applications) and select the correct answer using the codes given below the lists: List I List II A. Trepanning tool 1. For surface finishing by honing h i B. Side milling cutter 2. For machining gears C. Hob cutter 3. For cutting keyways in shafts D. Abrasive sticks 4. For drilling large diameter holes Codes:A B C D A B C D (a) 1 3 2 4 (b) 4 3 2 1 (c) 1 2 3 4 (d) 4 2 3 1

IES 1992
Gear lapping (a) An operation after heat treatment (b) An operation prior to heat treatment (c) An independent operation for gear reconditioning (d) None of the above

IES 1992
A surface finish of 0.025 0.1 micrometer CLA values is to by produced. Which machining process would you recommend? (a) Grinding (b) Rough turning (c) ( ) Lapping L i (d) Honing H i

IES 1992
Buffing wheels are mode of (a) Softer metals (b) Cotton fabric (c) Carbon (d) Graphite

Page 36 of 69

10/31/2011

IAS 2004
The size effect refers to the increase in specific cutting energy at low values of under formed chip thickness. It is due to which one of the following? (a) Existence of ploughing force (b) Work W k hardening h d i (c) High strain rate (d) Presence of high friction at chiptool interface.

IAS 2000
Consider the following statements in respect of a grinding wheel of specification, 51A 36L7R23, using the standard alphanumeric codification: 1. Abrasive used in the wheel is aluminum oxide 2. The Th grain i size i of f abrasive b i is i medium di 3. The wheel grade is medium hard 4. It has an open structure 5. It has resinoid as bonding agent Which (If these statements are correct? (a) 1, 2 and 3 (b) 1, 3 and 4 (c) 2, 3 and 5 (d) 1, 4 and 5

IAS 1999
Assertion (A): The grade of a grinding wheel is a measure of hardness of the abrasive used for the wheel. Reason (R): Grading is necessary for making right selection of the wheel for a particular work. work (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IAS 2001
Consider the following statements: The setup for internal centreless grinding consists of a regulating wheel, a pressure roll and a support roll, between which the tubular workpiece is supported with the grinding wheel within the tube, wherein 1.The grinding wheel, workpiece and regulating wheel centers must lie on one line 2.The directions of rotation of workpiece and grinding wheel are same 3.The directions of rotation of pressure roll, support roll and regulating wheel are same 4.The directions of rotation of grinding wheel and regulating wheel are same Which of these statements are correct? (a) 1, 2 and 3 (b) 1, 3 and 4 (c) 2 and 3 (d) 3 and 4

IAS 1997
Which of the following pairs are correctly matched? 1. Drill press : Trepanning 2. Centreless grinding: Through feeding 3. Capstan lathe: Ram type turret Select the correct answer using the codes given below: Codes: (a) 1 and 2 (b) 1, 2 and 3 (c) 1 and 3 (d) 2 and 3

IAS 2007
Match List I with List II and select the correct answer using the code given below the Lists: List I List II (Machine Tool/ Cutting Tool) (Part/ Characteristics) A. Screw cutting g lathe1. Self locking g taper p B. Drill 2. Chasing dial C. End mill 3. Wiper insert D. Grinding wheel 4. Self releasing taper 5. Balance weights Code:A B C D A B C D (a) 4 5 3 1 (b) 2 1 4 5 (c) 4 1 3 5 (d) 2 5 4 1

Page 37 of 69

10/31/2011

IAS 1999
Which one of the following processing sequences will give the best accuracy as well as surface finish? (a) Drilling, reaming and grinding (b) Drilling, boring and grinding (c) Drilling, reaming and lapping (d) Drilling, reaming and electroplating

IAS 2001
Which one of the following grinding wheels (with Grade, Grit and Bond) is suitable for cutter grinding? (a) K 60 vitrified (b) K 320 vitrified (c) (d) T 320 resinoid ( ) T 60 6 resinoid i id i id

Page 38 of 69

10/31/2011

GATE 2006

NTMM
BySKMondal

Arrange the processes in the increasing order of their maximum material removal rate. Electrochemical Machining (ECM) Ultrasonic Machining (USM) Electron Beam Machining (EBM) Laser Beam Machining (LBM) and Electric Discharge Machining (EDM) (a) USM, LBM, EBM, EDM, ECM (b) EBM, LBM, USM, ECM, EDM (c) LBM, EBM, USM, ECM, EDM (d) LBM, EBM, USM, EDM, ECM

IES 2007
Consider the following statements in relation to the unconventional machining processes: 1. Different forms of energy directly applied to the piece to have shape transformation or material removal from work surface. surface 2. Relative motion between the work and the tool is essential. 3. Cutting tool is not in physical contact with work piece. (a) 1 and 2 only (b) 1, 2 and 3 only (c) 2 and 3 only (d) 1 and 3 only

IES 2009
Which one of the following statements is correct in respect of unconventional machining processes? (a) The cutting tool is in direct contact with the job (b) The tool material needs to be harder than the job material t i l (c) The tool is never in contact with the job (d) There has to be a relative motion between the tool and the job

IAS 2002
Match List I (Processes) with List II (Tolerances obtained) and select the correct answer using the codes given below the Lists: List I List II (Processes) (Tolerances obtained) A. Plasma Arc machining 1. 75 microns B. Laser Beam machining 2. 25 microns C. Abrasive Jet machining 3. 50 microns D. Ultrasonic machining 4. 125 microns Codes:A B C D A B C D (a) 4 1 3 2 (b) 3 2 4 1 (c) 4 2 3 1 (d) 3 1 4 2

PSU
ECMcannotbeundertakenfor (a)steel (b)Nickelbasedsuperalloy (c)Al2O3 (d)Titaniumalloy

Page 39 of 69

10/31/2011

PSU
Commercial ECM is carried out at a combination of (a) low voltage high current (b) low current low voltage (c) high current high voltage (d) low current low voltage

Example
UsingECMremove5cm3/minfromanironworkpiece, whatcurrentisrequired? Atomicweightofiron56,density7.8g/cm3 valency,2

Example
Calculate the material removal rate and the electrode feed rate in the electrochemical machining of an iron surface that is 25 mm 25 mm in crosssection using NaCl in water as electrolyte. The gap between the tool and the workpiece is 0.25 mm. The supply voltage is 12 V DC. The specific resistance of the electrolyte is 3 c m For iron, Valency, Z = 2 Atomic weight, A = 55.85 Density, = 7860 kg / m3

Example(GATE2009)
Electrochemicalmachiningisperformedtoremove materialfromanironsurfaceof20mmx20mmunder thefollowingconditions: Interelectrodegap = 0.2mm S Supply l Voltage V lt (DC) = 12V Specificresistanceofelectrolyte =2 cm AtomicweightofIron = 55.85 Valency ofIron = 2 Faraday'sconstant = 96540Coulombs Thematerialremovalrate(ing/s)is

Example
Composition of a Nickel superalloy is as follows: Ni = 70.0%, Cr = 20.0%, Fe = 5.0% and rest Titanium Calculate rate of dissolution if the area of the tool is 1500 mm2 and a current of 1000 A is being passed through the cell. cell Assume dissolution to take place at lowest valancy of the elements.

Example
The electrochemical machining of an iron surface that is 25 mm 25 mm in crosssection using NaCl in water as electrolyte. The gap between the tool and the workpiece is 0.25 mm. The supply voltage is 12 V DC. The specific resistance of the electrolyte is 3 cm. Estimate the electrolyte flow rate. Specific heat of the electrolyte is given as 0.997 cal/gC. The ambient temperature is 35C and the electrolyte boiling temperature, is 95C. Density, = 7860 kg/cm3

Page 40 of 69

10/31/2011

Example
In ECM operation of pure iron an equilibrium gap of 2 mm is to be kept. Determine supply voltage, if the total overvoltage is 2.5 V. The resistivity of the electrolyte is 50 mm and the set feed rate is 0.25 mm/min.

GATE 1994
Electric discharge machining is more efficient process than Electrochemical machining for producing large noncircular holes. The above statement is (a) ( ) True T (b) False (c) Cant say (d) Insufficient data

GATE 2008
A researcher conducts electrochemical machining (ECM) on a binary alloy (density 6000 kg/m3) of iron (atomic weight 56, valency 2) and metal P (atomic weight 24, valency 4). Faraday's constant = 96500 coulomb/mole. Volumetric material removal rate of the alloy is 50 mm3/s at a current of 2000 A. The percentage of the metal P in the alloy is closest to (a) 40 (b) 25 (c) 15 (d) 79

GATE 2001
In ECM, the material removal is due to (a) Corrosion (b) Erosion (c) Fusion (d) Ion displacement

GATE 1997
Selection electrolyte for ECM is as follows: (a) Nonpassivating electrolyte for stock removal and passivating electrolyte for finish control (b) Passivating electrolyte for stock removal and non passivating i ti electrolyte l t l t for f finish fi i h control t l (c) Selection of electrolyte is dependent on current density (d) Electrolyte selection is based on tool work electrodes

GATE 1992
The two main criteria for selecting the electrolyte in Electrochemical Machining (ECM) is that the electrolyte should (a) Be chemically stable (b) Not N t allow ll dissolution di l ti of f cathode th d material t i l (c) Not allow dissolution of anode material (d) Have high electrical conductivity

Page 41 of 69

10/31/2011

GATE 1997
Inter electrode gap in ECG is controlled by (a) Controlling the pressure of electrolyte flow (b) Controlling the applied static load (c) Controlling the size of diamond particle in the wheel (d) Controlling the texture of the work piece

IES 2002
Assertion (A): In ECM, the shape of the cavity is the mirror image of the tool, but unlike EDM, the tool wear in ECM is less. Reason (R): The tool in ECM is a cathode. (a) and ( ) Both B th A and d R are individually i di id ll true t d R is i the th correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1997
Which one of the following processes does not cause tool wear? (a) Ultrasonic machining (b) Electrochemical machining (c) Electric discharge machining (d) Anode mechanical machining

IES2011Conventional
Discuss the effects of insufficient dielectric and electrolyte circulation in the interelectrode gap on the Electric Discharge machining and Electro Chemical Machining process respectively. [5 Marks]

IES2009Conventional
What is the principle of metal removal in EDM process? ii. Describe the process with the help of sketch. iii. List advantages and limitations of the system.
i.
[15marks]

GATE 2004
The mechanism of material removal in EDM process is (a) Melting and Evaporation (b) Melting and Corrosion (c) Erosion and Cavitation (d) Cavitation and Evaporation

Page 42 of 69

10/31/2011

GATE 2003
As tool and work are not in contact in EDM process (a) No relative motion occurs between them (b) No wear of tool occurs (c) No power is consumed during metal cutting (d) No force between tool and work occurs

GATE 1999
In ElectroDischarge Machining (EDM), the tool is made of (a) Copper (b) High Speed Steel (c) Cast Iron (d) Plain Carbon Steel

GATE 2007
In electro discharge machining (EDM), if the thermal conductivity of tool is high and the specific heat of work piece is low, then the tool wear rate and material removal rate are expected to be respectively (a) High and high (b) Low and low (c) High and low (d) Low and high

GATE 2005
A zigzag cavity in a block of high strength alloy is to be finish machined. This can be carried out by using (a) Electricdischargemachining (b) Electrochemicalmachining (c) Laserbeammachining (d) Abrasiveflowmachining

IES 2005
Which of the following is/are used as low wearing tool material(s) in electric discharge machining? (a) Copper and brass (b) Aluminium and graphite (c) Silver tungsten and copper tungsten (d) Cast iron

GATE 2000
Deep hole drilling of small diameter, say 0.2 mm is done with EDM by selecting the tool material as (a) Copper wire (b) Tungsten wire (c) Brass wire (d) Tungsten carbide

Page 43 of 69

10/31/2011

GATE 1994
Ultrasonic machining is about the best process for making holes in glass which are comparable in size with the thickness of the sheet. The above statement is (a) ( ) True T (b) False (c) Cant say (d) Insufficient data

IES2011
USM has good machining performance for : (a) Al (b) Steel ( ) Super p alloys y (c) (d) Refractory material

GATE 1993
In ultrasonic machining process, the material removal rate will be higher for materials with (a) Higher toughness (b) Higher ductility (c) Lower toughness (d) Higher fracture strain

GATE 1992
In Ultrasonic Machining (USM) the material removal rate would (a) Increase (b) Decrease (c) Increase and then decrease (d) decrease and then increase with increasing mean grain diameter of the abrasive material.

IES 2009
By which one of the following processes the metering holes in injector nozzles of diesel engines can be suitably made? (a) Ultrasonic machining (b) Abrasive Ab i jet j t machining hi i (c) Electron beam machining (d) Chemical machining

IES 2006
During ultrasonic machining, the metal removal is achieved by (a) High frequency eddy currents (b) high frequency sound waves (c) Hammering action of abrasive particles (d) Rubbing action between tool and workpiece

Page 44 of 69

10/31/2011

IAS 1996
During ultrasonic machining, the metal removal is affected by the (a) Hammering action of abrasive particles (b) Rubbing action between tool and workpiece (c) High frequency sound waves (d) High frequency eddy currents

GATE 1992
Match the following components with the appropriate machining processes: Component Process (A) Square hole in a high strength alloy (1) Milling ( ) Square q p ( ) g (B) hole in a ceramic component (2) Drilling (C) Blind holes in a die (3) ECM (D) Turbine blade profile on high strength alloy(4) Jig boring (5) EDM (6) USM Codes:A B C D A B C D (a) 4 1 2 3 (b) 5 6 1 3 (c) 4 2 1 3 (d) 3 1 2 4

Match the following non traditional machining processes with the corresponding material removal mechanism:
Machiningprocess P.Chemicalmachining Q. Q Electro chemical machining R.Electro discharge machining S.Ultrasonicmachining Mechanismofmaterialremoval 1.Erosion 2 Corrosivereaction 2. 3.Iondisplacement 4.Fusionandvaporization

GATE2011

GATE 2007
Matchthemostsuitablemanufacturingprocessesfor thefollowingparts. Parts ManufacturingProcesses P. Computerchip 1. ElectrochemicalMachining Q Metalformingdiesandmoulds Q. 2. UltrasonicMachining R. Turbineblade 3. Electrodischarge Machining S. Glass 4. PhotochemicalMachining Codes:P Q R S P Q R S (a) 4 3 1 2 (b) 4 3 2 1 (c) 3 1 4 2 (d) 1 2 4 3

(a)P 2,Q 3,R 4,S 1(b)P 2,Q 4,R 3,S 1 (c)P 3,Q 2,R 4,S 1(d)P 2,Q 3,R 1,S 4

GATE 1998
List I (A) ECM (B) EDM (C) USM (D) LBM (1) (2) (3) (4) (5) (6) C 2 1 List II Plastic shear Erosion/Brittle fracture Corrosive reaction Melting and vaporization Ion displacement Plastic shear and ion displacement D A B C D 3 (b) 5 4 2 4 3 (d) 3 1 2 4

IES 2008
Match ListI with ListII and select the correct answer using the code given below the lists: ListI ListII (Unconventional machining process) (Basic process) A Electro polishing A. 1 1. Thermal B. Electrochemical machining 2. Mechanical C. Abrasive jet machining 3. Electrochemical D. Electrical discharge machining 4. Chemical Code:A B C D A B C D (a) 4 3 2 1 (b) 2 1 4 3 (c) 4 1 2 3 (d) 2 3 4 1

Codes:A (a) 4 (c) 4

B 1 2

Page 45 of 69

10/31/2011

IES 1998
Match ListI (Machining process) with ListII (Associated medium) and select the correct answer using the codes given below the lists: ListI ListII A. 1. Kerosene A Ultrasonic Ult i machining hi i K B. EDM 2. Abrasive slurry C. ECM 3. Vacuum D. EBM 4. Salt solution Code:A B C D A B C D (a) 2 3 4 1 (b) 2 1 4 3 (c) 4 1 2 3 (d) 4 3 2 1

IES 2005
Match List I (Machining Process) with List II (Application) and select the correct answer using the code given below the Lists: List I List II A. EDM 1. Holes & cavities in hard & brittle materials B. Microdrilling & microwelding of B LBM 2. 2 materials C. USM 3. Shaping of hard metals or reshaping of cemented carbide tools D. ECM 4. Shaping of cemented carbide dies and punches Codes:A B C D A B C D (a) 4 1 2 3 (b) 3 2 1 4 (c) 4 2 1 3 (d) 3 1 2 4

IES 2003
Match List I (Materials) with List II (Machining) and select the correct answer using the codes given below the Lists: List I List II (Materials) (Machining) A. Machining of conducting materials 1. ECM B. Ruby rod 2. EDM C. Electrolyte 3. USM D. Abrasive slurry 4. LBM Codes:A B C D A B C D (a) 4 2 1 3 (b) 4 2 3 1 (c) 2 4 3 1 (d) 2 4 1 3

IES 2003
Assertion (A): Water jet machining uses high pressure and high velocity water stream which acts like a saw and cuts a narrow groove in the material. Reason (R): The force required for cutting is generated from sudden change in the momentum of the water stream. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IAS 2002
Which one of the following pairs is NOT correctly matched? (Unconventional (Application) machining method) (a) Electric discharge : Machining of electrically conductive materials (b) Laser beam : Micromachining (c) Plasma arc : Faster cutting of hard materials (d) Electron beam : Faster metal removal rate

IAS 1999
Match List I (Unconventional machining process) with List II (Typical application) and select the correct answer using the codes given below the lists: List I List II A Electro discharge machining 1. A. 1 Drilling micro holes in very hard metals B. Electro chemical machining 2. Drilling holes in glass C. Ultrasonic machining 3. Die sinking D. Laser beam machining 4. Machining contours Codes:A B C D A B C D (a) 4 2 3 1 (b) 3 4 1 2 (c) 4 3 2 1 (d) 3 4 2 1

Page 46 of 69

10/30/2011

NC,CNC&Robotics

IAS 1996
Assertion (A): The temperature control of an electric iron is an example of servomechanism. Reason (R): It is an automatic control system. (a) Both A and R are individually true and R is the correct t explanation l ti of fA (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

BySKMondal

GATE 1994
CNC machines are more accurate than conventional machines because they have a high resolution encoder and digital readouts for positioning. True T or false? f l ?

IES 1999
Consider the following statements numerically controlled machine tools: 1. They reduce nonproductive time 2. They reduce fixturing 3. They reduce maintenance cost Which of these statements are correct? (a) 1, 2 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1 and 3 regarding

IES 1995
Consider the following characteristics of production jobs: 1. Processing of parts frequently in small lots 2. Need to accommodate design changes of products. 3. Low rate of metal removal 4. Need for holding close tolerances The characteristics which favour the choice of numerically controlled machines would include (a) 1, 2 and 3 (b) 2, 3 and 4 (c) 1, 3 and 4 (d) 1, 2 and 4

IES 2009
In which of the following machining manual part programming is done? (a) CNC machining (b) NC machining (c) DNC machining (d) FMS machining

Page 47 of 69

10/30/2011

GATE 1993
With reference to NC machine, which of the following statement is wrong? (a) Both closedloop and openloop control systems are used (b) Paper tapes, floppy tapes and P t fl t d cassettes tt are used d for f data storage (c) Digitizers may be used as interactive input devices (d) Post processor is an item of hardware

IES 2007
What are the main components of an NC machine? 1. Part program 2. Machine Control Unit 3. Servo motor Select the correct answer using the code given below: (a) 1, 2 and 3 (b) 1 and 2 only (c) 2 and 3 only (d) 1 and 3 only

JWM2010
Consider the following components regarding numerical control system : 1. Programme of instructions 2. Machine control unit 3. Processing P i equipment i Which of these are correct ? (a) 1, 2 and 3 (b) 1 and 2 only (c) 2 and 3 only (d) 1 and 3 only

IES 2009
What is the purpose of satellite computers in Distributed Numerical Control machines? (a) To act as standby systems (b) To share the processing of largesize NC programs (c) To serve a group of NC machines (d) To network with another DNC setup

IES 1999
Consider the following components: 1. A dedicated computer 2. Bulk memory 3. Telecommunication lines Which of these components are required for a DNC system? (a) 2 and 3 (b) 1 and 2 (c) 1, 2 and 3 (d) 1 and 3

JWM2010
ConsiderthefollowingadvantagesofDNCsystems: 1.Timesharing 2.Greatercomputationalcapability 3.Remotecomputerlocation Whichoftheaboveis/arecorrect? (a)1and2only (b)2and3only (c)2only (d)1,2and3

Page 48 of 69

10/30/2011

IES 2002S1
Match List I with List II and select the correct answer: List I List II (NC machine tool systems) (Features) A. It has an integrated automatic tool A NC system 1. 1 changing unit and a component indexing device B. CNC system 2. A number of machine tools are controlled by a computer. No tape reader, the part program is transmitted directly to the machine tool from the computer memory
C.

IES 2002Contd..FromS1
DNC system 3. The controller consists of softwired computer and hard wired logic Graphic display of tool path is also possible The instructions on tape is prepared in binary decimal form and operated by a series of coded instructions A B C D (b) 1 3 2 4 (d) 1 2 3 4

D. Machining centre 4.

Codes:A (a) 4 (c) 4

B 2 3

C 3 2

D 1 1

GATE 2007
WhichtypeofmotorisNOTusedinaxisorspindle drivesofCNCmachinetools? (a) Inductionmotor (b) DCservomotor (c) Steppermotor (d) Linearservomotor

IES 1994
Feed drives in CNC milling machines are provided by (a) Synchronous motors (b) Induction motors (c) Stepper motors (d) Servomotors.

IES 2002
In a CNC machine tool, encoder is used to sense and control (a) Table position (b) Table velocity (c) Spindle speed (d) Coolant flow

Example
A DC servomotor is coupled directly to a leadscrew

which drives the table of an NC machine tool. A digital encoder, which emits 500 pulses per revolution, is mounted on the other end of the leadscrew If the leadscrew pitch is 5 mm and the leadscrew. motor rotates at 600 rpm, calculate (a) The linear velocity of the table (b) The BLU of the NC system (c) The frequency of pulses transmitted by the encoder.

Page 49 of 69

10/30/2011

IES2011Conventional
The table of a CNC machine is driven by a Lead screw which

StatementforLinkedAnswersquestions:S1
In the feed drive of a PointtoPoint open loop CNC drive, a stepper motor rotating at 200 steps/rev drives a table through a gear box and lead screwnut mechanism (pitch = 4 mm, number of starts = 1). Output rotational speed The gear ratio = Input rotational speed is given by U = 1 4 The stepper motor (driven by voltage pulses from a pulse generator) executes 1 step/pulse of the pulse generator. The frequency of the pulse train from the pulse generator is f = 10,000 pulses per minute.

is rotated by a DC servomotor. A digital encoder which emits 1000 pulses per second is mounted on the lead screw as a pitch is 6 mm and motor feedback device. If the lead screw p rotates at 500 rpm, find
1. 2. 3.

Basic length Units of the system Linear velocity of the table. Frequency of pulses generated by the feedback device. [5 Marks]

GATE 2008Q1 (StatementinS1)

GATE 2008Q2 (StatementinS1)

GATE 1992
In a pointtopoint type of NC system (a) Control of position and velocity of the tool is essential (b) Control of only position of the tool is sufficient (c) Control of only velocity of the tool is sufficient (d) Neither position nor velocity need be controlled

GATE 2006
NC contouring is an example of (a) Continuous path positioning (b) Pointtopoint positioning (c) Absolute positioning (d) Incremental positioning

Page 50 of 69

10/30/2011

GATE2005
WhichamongtheNCoperationsgivenbeloware continuouspathoperations?
ArcWelding(AW) Milling(M) g( (D) ) Punching gisSheetMetal( (P) ) Drilling LaserCuttingofSheetMetal(LC)SpotWelding(SW)

IES 2000
Assertion (A): The axis of an NC drilling machine spindle is denoted as zaxis. Reason (R): In NC machine tool, the axis perpendicular to both x and yaxis is designated as zaxis (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

(a) AW,LCandM (c) D,LC,PandSW

(b)AW,D,LCandM (d)D,LC,andSW

IES 1996
Assertion (A): Numerically controlled machines having more than three axes do not exist. Reason (R): There are only three Cartesian coordinates namely xyz. (a) ( ) Both B th A and d R are individually i di id ll true t and d R is i the th correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 2003S1
While part programming in CNC machines, the input of dimensional information for the tool path can be given in the absolute coordinate system or in incremental coordinate system. The above figure shows the route to be followed by the tool from O to C, i.e., O A B C.

IES 2003Contd..FromS1
If incremental coordinates system is used, the co ordinates of each point A, B and C are (a) A: X 5.0, Y 10.0 (b) A: X 5.0, Y 10.0 B: X 20.0, Y5.0 B: X 25, Y 15.0 C: X 10.0, Y 10.0 C: X 35, Y 5.0 (c) A: X 10.0, Y 5.0 (d) A: X 10.0, Y 5.0 B: X 15.0, Y 25.0 B: X 5.0, Y 20.0 C: X 15.0, Y 35.0 C: X 10.0, Y 10.0

GATE 2004
During the execution of a CNC part program block N020 G02 X45.0 Y25.0 R5.0 the type of tool motion will be (a) Circular Interpolation clockwise (b) Circular Interpolation counter clockwise (c) Linear Interpolation (d) Rapid feed

Page 51 of 69

10/30/2011

GATE 2010
In a CNC program block, N002 G02 G91 X40 Z40, G02 and G91 refer to (a) Circular interpolation in counterclockwise direction and incremental dimension (b) Circular Ci l interpolation i t l ti in i counterclockwise t l k i direction di ti and absolute dimension (c) Circular interpolation in clockwise direction and incremental dimension (d) Circular interpolation in clockwise direction and absolute dimension

IES 2009
Interpolation in the controller refers to control of which one of the following in a CNC machine? (a) Loading/unloading of jobs on machine (b) Loading/unloading of tools from the tool changer (c) Axes of machine for contouring (d) Coolant and miscellaneous functions on machine

GATE 2001
In an NC machining operation, the tool has to be moved from point (5, 4) to point (7, 2) along a circular path with centre at (5, 2). Before starting the operation, the tool is at (5, 4). The correct G and M code for this motion is (a) N010 G03 X7.0 Y2.0 I5.0 J2.0 (b) N010 G02 X7.0 Y2.0 I5.0 J2.0 (c) N010 G01 X7.0 Y2.0 I5.0 J2.0 (d) N010 G00 X7.0 Y2.0 I5.0 J2.0

GATE 2005
The tool of an NC machine has to move along a circular arc from (5, 5) to (10,10) while performing an operation. The centre of the arc is at (10, 5). Which one of the following NC tool path commands performs the above mentioned operation? (a) N010G02 X10 Y10 X5 Y5 R5 (b) N010G03 X10 Y10 X5 Y5 R5 (c) N010G01 X5 Y5 X10 Y10 R5 (d) N010G02 X5 Y5 X10 Y10 R5

GATE 2000
In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30), and (50, 0). By applying cutter radius right compensation, the trajectory of the cutter will be (a) (5, 0), (5, 35), (55, 35), (55, 5), (5, 5) (b) (0, 5), (55, 5), (55, 35), (5, 35), (5, 5) (c) (5, 5), (5, 25), (45, 25), (45, 5), (5, 5) (d) (5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

GATE 2009

Page 52 of 69

10/30/2011

IES 1993
A 'block' of information in N.C. machine program means (a) One row on tape (b) A word comprising several rows on tape (c) One complete instruction (d) One complete program for a job

IES 1996
In manual programming and tape preparation for a NC drilling machine, the spindle speed was coded as S 684 (using the magicthree code). The spindle speed in rpm will be (a) 684 (b) 68.4 (c) 840 (d) 6840

IES 1995
Match List I with List II and select the correct answer using the codes given below the lists: List I List II (A function connected (Associated parameter) with NC m/c tool) A. A Interpolation 1. 1 Tape preparation B. Parity check 2. Canned cycle C. Preparatory function 3. Drilling D. Point to point control 4. Contouring 5. Turning Code:A B C D A B C D (a) 4 1 2 3 (b) 4 1 2 5 (c) 5 1 3 2 (d) 1 4 3 2

IES 1998
Which of the following are the rules of programming NC machine tools in APT language? 1. Only capital letters are used 2. A period is placed at the end of each statement 3. Insertion of space does not affect the APT word Select the correct answer using the codes given below: (a) 1 and 2 (b) 2 and 3 (c) 1and 3 (d) 1 alone

Name the four types of statements in a complete APT part program. Prepare part program for geometry description of the contour shown in the figure below: Y [15Marks]
30

IES2008
40

Prepare part using APT language for milling the contour shown in Fig. in a single pass. D [20Marks]
C 110 B R30 Q

IES2007

20
L2

L3

135

20

C1

110 120 E R40

80

L4
L1

+
40

C2 L5

A
R 20

F 100

+ 40

P2

20

P1

P Material : M S. 8 mm

Page 53 of 69

10/30/2011

Prepare part program to machine the contour shown in the figure using APT on CNC milling machine. [15Marks] R30

R20

IES2006

IES2011Conventional
State the method of defining line segment of cutter motion using APT program format. [5 Marks]

100 mm 80

60 200 mm

50

Material: MS

Thickness: 8.0 mm

IES 1997
Which of the following are valid statements for point to point motion of the tool in APT language? 1. GO/TO/............ 2. GO DLTA/............ 3. GO/TO, . Select the correct answer using the codes given below: (a) 1 and 2 (b) 2 and 3 (c) 1 and 3 (d) 1, 2 and 3

IES 1995
In APT language, the cutter motion in incremental coordinate mode is addressed as (a) GO/TO/..... (b) GO/TO..... (c) GO DLTA/.... (d) GO FWD/...

IES2011
Trajectoryofarobotmean: (a)Pathtracedbytheendeffectors (b)KinematicsofRobot ( (c) )Robotj joints (d)Robotprogramming

IES2010
Consider the following statements: Good dynamic performance is usually difficult to achieve in robots which contain a rotary base because 1. Position, speed and acceleration of the other joints cause variations in the reflected torque and moment of inertia. 2. The moment of inertia reflected at the base depends upon the weight of the object being carried. 3. The moment of inertia reflected at the base also depends upon the distance between the base axis and the manipulated object. Which of the above statements is/are correct? (a) 1, 2 and 3 (b) 2 and 3 only (c) 1 only (d) 1 and 3 only

Page 54 of 69

10/30/2011

IES 2006
Which one of the following is the third basic component of robots besides power supply and control (memory) console? (a) Software (b) Coaxial cable (c) ( ) Mechanical M h i l unit it arm (d) Microcomputer Mi t

IES 2000
Consider the following characteristics of a robot: 1. The tip of the robot arm moves from one point to another with its inbetween path not being defined. 2. It can be used for drilling holes at difference points in a workpiece. workpiece 3. It can be used for V butt joint welding between two points. 4. The memory capacity required for its control unit is low. Which of these are the characteristics associated with a point to point robot? (a) 1 and 2 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 2, 3 and 4

IES 2006
Which item best describes a CAM technology? (a) Geometric modeling (b) Documentation (c) Drafting (d) Numerical control

IES 1996
Whichofthefollowingpairsarecorrectlymatched? 1. CNCmachinePostprocessor 2. Machiningcentre.Toolmagazine 3. DNC.FMS (a) 1,2and3 (b) 1and2 (c) 1and3 (d)2and3

IES 2006
Flexible manufacturing allows for: (a) Tool design and production (b) Automated design (c) Quick and inexpensive product change (d) Quality control

IES 2004
Consider the following characteristics: 1. Single machine tool 2. Manual materials handling system 3. Computer control 4. Random sequencing of parts to machines Which of the above characteristics are associated with flexible manufacturing system? (a) 1, 2 and 3 (b) 1 and 2 (c) 3 and 4 (d) 2, 3 and 4

Page 55 of 69

10/31/2011

GATE 1999

JigsandFixtures
BySKMondal

Choosethecorrectstatement: (a) Afixtureisusedtoguidethetoolaswellastolocate andclamptheworkpiece (b) AJigisusedtoguidethetoolaswellastolocateand clamp l the th workpiece k i (c) JigsarcusedonCNCmachinestolocateandclamp theworkpieceandalsotoguidethetool (d) Noarrangementtoguidethetoolisprovidedinajig.

IES 2007
According to the principle of location in jigs and fixtures, how many degrees of freedom are to be eliminated to have a body fixed in space? (a) 3 (b) 4 (c) 5 (d) 6

GATE 2005
When 321 principle is used to support and locate a three dimensional workpiece during machining, the number of degrees of freedom that are restricted is (a) 7 (b) 8 (c) 9 (d) 10

GATE 2001
321 method of location in a jig or fixture would collectively restrict the workpiece in n degrees of freedom, where the value of n is (a) 6 (b) 8 (c) 9 (d) 12

IES2011
Inthe321principleoffixture3referstonumberof : (a)Setupspossible (b)Clampsrequired (c)Positionsonprimaryface (d)Locatingpositions

Page 56 of 69

10/31/2011

IES 1998,1999
Diamond pin location is used in a fixture because (a) It does not wear out (b) It takes care of any variation in centre distance between two holes (c) It is easy to clamp the part on diamond pins (d) It is easy to manufacture

IES 2009
A lever having two precisely drilled holes, one smaller than the other, has to be located in a fixture using hardened and ground plugs for further machining in relation to the holes. Select the correct method of locating the lever from the given alternatives. lt ti (a) Using two hardened and ground plugs, the smaller one having flats machined on each side (b) Using two hardened and ground plugs (c) Using one hardened and ground plug and one V block (d) Using two Vblocks

IES 1995
If the diameter of the hole is subject to considerable variation, then for locating in jigs and fixtures, the pressure type of locator used is (a) Conical locator (b) Cylindrical locator (c) Diamond pin locator (d) Vee locator

IES 2005
Match List I (An Element of Jigs and Fixtures) with List II (Associating System) and select the correct answer using the code given below the Lists: List I List II A Bush 1. Milling fixture B. Setting block 2. Turning fixture C. Diamond pin 3. Radial location D. Vblock 4. Cylindrical location 5. Drill jigs Codes:A B C D A B C D (a) 5 4 3 1 (b) 3 1 2 4 (c) 5 1 3 4 (d) 3 4 2 1

IES 2000
Match List I (Components used in jigs and fixtures) with List II (Their functions) and select the correct answer using the codes given below the Lists: List I List II A. Jack pin 1. To guide the drill bit during machining B. Vlocator 2. For easy y removal of the work p piece from the jig or fixture after the machining operation is over C. Bushes 3. To locate the circular or semicircular objects in a jig or fixture D. Ejectors 4. To locate work piece whose dimensions are subject to variations Code: A B C D A B C D (a) 3 4 1 2 (b) 4 3 1 2 (c) 3 4 2 1 (d) 4 3 2 1

IES 1995
Match List I with List Ii and select the correct answer using the codes given below the lists: List I (Task) List II (Recommendation) A. Three components in a straight 1. Clamp with a floating pad. line should worked in one loading Unloading of clamp element from jig is essential 2. Quick action nut 3. Cam clamp 4. Equalising clamp 5. Strap clamp Code: A B C D A B C D (a) 5 2 3 4 (b) 4 2 1 5 (c) 1 4 2 3 (d) 4 1 5 3 C. Clamping of rough surfaces D. Need for heavy clamping force B.

Page 57 of 69

10/31/2011

IES 2005
Which one of the following is the most significant property to be considered in the selection of material for the manufacture of locating pins and drill jig buses used in jigs and fixtures? (a) Wearresistance (b) Elasticity (c) Shearstrength (d) Tensilestrength

IES 1996
Assertion (A): A workpiece with rough unmachined surface can be located in a jig or fixture on three supporting points. Reason (R): Indexing is made accurate by supporting on three points. points (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES 1996
Consider the following statements: The cutter setting block in a milling fixture 1. Sets the cutting tool with respect of two of its surfaces. 2. Limits the total travel required by the cutter during machining. 3. Takes location from the location scheme of the component. (a) 1,2 and 3 are correct (b) 1 and 2 are correct (c) 2 and 3 are correct (d) 1 and 3 are correct

IES 1993
The floating position of the holding fixture in a rotary transfer device is used to (a) Improve the accuracy of location (b) Reduce the tendency to over index (c) Reduce the cycle time (d) Improve upon the acceleration and deceleration characteristics

Page 58 of 69

10/31/2011

GATE 2001
Allowance in limits and fits refers to (a) Maximum clearance between shaft and hole (b) Minimum clearance between shaft and hole (c) Difference between maximum and minimum size of hole (d) Difference between maximum and minimum size of shaft

Limit, Limit Tolerance&Fits

BySKMondal

GATE 1998
In the specification of dimensions and fits, (a) Allowance is equal to bilateral tolerance (b) Allowance is equal to unilateral tolerance (c) Allowance is independent of tolerance (d) Allowance is equal to the difference between maximum and minimum dimension specified by the tolerance.

GATE 2010
A shaft has a dimension,350.025 The respective values of fundamental deviation and tolerance are
0.009

(a) 0.025, 0.008 (c) 0.009, 0.008

(b) 0.025,0.016 (d) 0.009,0.016

GATE 1992
TwoshaftsAandBhavetheirdiametersspecifiedas 100 0.1mmand0.1 0.0001mmrespectively. Whichofthefollowingstatementsis/aretrue? (a) ToleranceinthedimensionisgreaterinshaftA (b) Therelativeerrorinthedimensionisgreaterinshaft A (c) ToleranceinthedimensionisgreaterinshaftB (d) Therelativeerrorinthedimensionissameforshaft AandshaftB
+0.040 0.0100

GATE 2004
In an interchangeable assembly, shafts of size +0.020 25.000 mm mate with holes of size 25.0000.000 mm. The maximum possible clearance in the assembly will be ( ) 10 microns (a) i (b) 20 microns (c) 30 microns (d) 60 microns

Page 59 of 69

10/31/2011

GATE 2007
0 .0 5 0 0 .0 0 0

IES 2005
The tolerance specified by the designer for the diameter of a shaft is 20.00 0.025 mm. The shafts produced by three different machines A, B and C have mean diameters of 1999 mm, 2000 mm and 20.01 mm respectively, with same standard deviation. What rejection for d i ti Wh t will ill be b the th percentage t j ti f the shafts produced by machines A, B and C? (a) Same for the machines A, Band C since the standard deviation is same for the three machines (b) Least for machine A (c) Least for machine B (d) Least for machine C

A hole is specified as 4 0 mm. The mating shaft has a clearance fit with minimum clearance of 0.01 mm. The tolerance on the shaft is 0.04 mm. The maximum clearance in mm between the hole and the shaft is (a) 0.04 (b) 0.05 (c) 0.10 (d) 0.11

GATE 2000
A slot is to be milled centrally on a block with a dimension of 40 0.05 mm. A milling cutter of 20 mm width is located with reference to the side of the block within 0.02 mm. The maximum offset in mm between the centre lines of the slot and the block is (a) 0.070 (b) 0.070 (c) 0.020 (d) 0.045

IES2011
Interference fit joints are provided for: (a) Assembling bush bearing in housing (b) Mounting heavy duty gears on shafts (c) ( ) Mounting gp pulley y on shafts (d) Assembly of flywheels on shafts

GATE 2005
In order to have interference fit, it is essential that the lower limit of the shaft should be (a) Greater than the upper limit of the hole (b) Lesser than the upper limit of the hole (c) Greater than the lower limit of the hole (d) Lesser than the lower limit of the hole

GATE2011
A hole is of dimension 9
+0.015 +0

mm. The
+0.010

p g shaft is of dimension corresponding The resulting assembly has (a) loose running fit (b) close running fit (c) transition fit (d) interference fit

9 +0.001

mm.

Page 60 of 69

10/31/2011

IES 2007

IES 2006
Which of the following is an interference fit? (a) Push fit (b) Running fit (c) Sliding fit (d) Shrink fit

IES 2009
Consider the following joints: 1. Railway carriage wheel and axle 2. IC engine cylinder and liner Which of the above joints is/are the result(s) of interference fit? (a) 1 only (b) 2 only (c) Neither 1 nor 2 (d) Both 1 and 2

IES 2008
Consider the following statements: 1. The amount of interference needed to create a tight joint varies with diameter of the shaft. 2. An interference fit creates no stress state in the shaft. h ft 3. The stress state in the hub is similar to a thick walled cylinder with internal pressure. Which of the statements given above are correct? (a) 1, 2 and 3 (b) 1 and 2 only (c) 2 and 3 only (d) 1 and 3 only

IES 2004
Consider the following fits: 1. I.C. engine cylinder and piston 2. Ball bearing outer race and housing 3. Ball bearing inner race and shaft Which of the above fits are based on the interference system? (a) 1 and 2 (b) 2 and 3 (c) 1 and 3 (d) 1, 2 and 3

IES 2003
Match ListI (Phenomenon) with ListII (Significant Parameters/Phenomenon) and select the correct answer using the codes given below the Lists: ListI ListII (Phenomenon) (Significant / ) Parameters/Phenomenon) A. Interference fit 1. Viscosity index B. Cyclic loading 2. Interference C. Gear meshing 3. Notch sensitivity D. Lubricating of bearings 4. Induced compressive stress Codes:A B C D A B C D (a) 3 4 1 2 (b) 4 3 2 1 (c) 3 4 2 1 (d) 4 3 1 2

Page 61 of 69

10/31/2011

IES 2005
Assertion (A): Hole basis system is generally preferred to shaft basis system in tolerance design for getting the required fits. Reason (R): Hole has to be given a larger tolerance band than the mating shaft. shaft (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

IES2006Conventional
Find the limit sizes, tolerances and allowances for a 100 mm diameter shaft and hole pair designated by F8h10. Also specify the type of fit that the above pair belongs to. Given: 100 mm diameter lies in the diameter step range of 80120 mm. The fundamental deviation for shaft designation f is 5.5 D0.41 The values of standard tolerances for grades of IT 8 and IT 10 are 25i and 64i respectively. Also, indicate the limits and tolerance on a diagram. [15Marks]

IES 2008
Consider the following statements: A nomenclature 50 H8/p8 denotes that 1. Hole diameter is 50 mm. 2. It is a shaft base system. 3. 8 indicates fundamental deviation. Which of the statements given above is/are correct? (a) 1, 2 and 3 (b) 1 and 2 only (c) 1 and 3 only (d) 3 only

IES 2002
In the tolerance specification 25 D 6, the letter D represents (a) Grade of tolerance (b) Upper deviation (c) Lower deviation (d) Type of fit

GATE 2009
What are the upper and lower limits of the shaft represented by 60 f8? Use the following data: Diameter 60 lies in the diameter step of 5080 mm. Fundamental tolerance unit, i, in m= 0.45 D1/3 + 0.001D, where D is the representative size in mm; Tolerance value for lT8 = 25i. Fundamental deviation for 'f shaft = 5.5D0.41 (a) Lower limit = 59.924 mm, Upper Limit = 59.970 mm (b) Lower limit = 59.954 mm, Upper Limit = 60.000 mm (c) Lower limit = 59.970 mm, Upper Limit = 60.016 mm (d) Lower limit = 60.000 mm, Upper Limit = 60.046 mm

GATE 2000
A fit is specified as 25H8/e8. The tolerance value for a nominal diameter of 25 mm in IT8 is 33 microns and fundamental deviation for the shaft is 40 microns. The maximum clearance of the fit in microns is (a) 7 (b) 7 (c) 73 (d) 106

Page 62 of 69

10/31/2011

GATE 1996
The fit on a holeshaft system is specified as H7 s6.The type of fit is (a) Clearance fit (b) Running fit (sliding fit) (c) Push fit (transition fit) (d) Force fit (interference fit)

GATE 2003
The dimensional limits on a shaft of 25h7 are (a) 25.000, 25.021 mm (b) 25.000, 24.979 mm (c) 25.000, 25.007 mm (d) 25.000, 24.993 mm

GATE 2003

GATE 1997
Three blocks B1 , B2 and B3 are to be inserted in a channel of width S maintaining a minimum gap of width T = 0.125 mm, as shown in Figure. For P = 18. 18 75 0.08; 0 08; Q = 25.00 0.12; R = 28.125 0.1 and S = 72.35 + X, (where all dimensions are in mm), the tolerance X is
(a)+0.38 (b) 0.38 (c)+0.05 (d)0.05

IES 2000
Which one of the following tolerances set on inner diameter and outer diameter respectively of headed jig bush for press fit is correct? (a) G7 h 6 (b) F7 n6 (c) ( ) H 7h h6 (d) F7j6 F j6

GATE 2004
GO and NOGO plug gages are to be designed for a 0.05 hole 200.01 mm. Gage tolerances can be taken as 10% of the hole tolerance. Following ISO system of gage design, sizes of GO and NOGO gage will be respectively (a) 20.010 mm and 20.050 mm (b) 20.014 mm and 20.046 mm (c) 20.006 mm and 20.054 mm (d) 20.014 mm and 20.054 mm

Page 63 of 69

10/31/2011

GATE 1995
Checking the diameter of a hole using GONOGO gauges is an, example of inspection by ..(variables/attributes) The above statement is (a) ( ) Variables V i bl (b) Attributes (c) Cant say (d) Insufficient data

GATE 2006
A ring gauge is used to measure (a) Outside diameter but not roundness (b) Roundness but not outside diameter (c) Both outside diameter and roundness (d) Only external threads

Page 64 of 69

10/31/2011

GATE 2008

S1

MeasurementofLines&Surfaces

A displacement sensor (a dial indicator) measures the lateral displacement of a mandrel mounted on the taper hole inside a drill spindle. The mandrel axis is an extension of the drill spindle taper hole axis and the protruding portion of the mandrel surface is perfectly cylindrical. Measurements are taken with the sensor placed at two positions P and Q as shown in the figure. The readings are recorded as Rx = maximum deflection minus minimum deflection, corresponding to sensor position at X, over one rotation.

BySKMondal

GATE 2008contdfromS1
If Rp= RQ>0, which one of the following would be consistent with the observation? (A) The drill spindle rotational axis is coincident with the drill spindle taper hole axis (B) The drill spindle rotational axis intersects the drill spindle taper hole axis at point P (C) The drill spindle rotational axis is parallel to the drill spindle taper hole axis (D) The drill spindle rotational axis intersects the drill spindle taper hole axis at point Q

IES 1992
Which grade symbol represents surface rough of broaching? (a) N12 (b) N8 (c) N4 (d) N1

IES 2006
The M and Esystem in metrology are related to measurement of: (a) Screw threads (b) Flatness (c) Angularity (d) Surface finish

IES 2007
What is the dominant direction of the tool marks or scratches in a surface texture having a directional quality, called? (a) Primary texture (b) Secondary texture (c) ( ) Lay L (d) Flaw Fl

Page 65 of 69

10/31/2011

IES 2008
What term is used to designate the direction of the predominant surface pattern produced by machining operation? (a) Roughness (b) Lay ( ) Waviness (c) W i (d) Cut C t off ff

IES2010
Match List I with List II and select the correct answer using the code given below the lists: List I List II (Symbols for direction of lay) (Surface texture)

(a) (c)

A 4 4

B 2 1

C 1 2

D 3 3

(b) (d)

A 3 3

B 2 1

C 1 2

D 4 4

IES 2008

GATE 1997
List I List II (A) Surface profilometer 1. Calibration (B) Light Section Microscope 2. Form tester (C) Microkater 3. Film thickness measurement (D) Interferometer 4. Centre line average 5. Comparator 6. Surface lay measurement Codes:A B C D A B C D (a) 4 1 2 3 (b) 4 3 5 1 (c) 4 2 1 3 (d) 3 1 2 4

Page 66 of 69

11/1/2011

GATE 1998
Auto collimator is used to check (a) Roughness (b) Flatness (c) Angle (d) Automobile balance.

MiscellaneousofMetrology

BySKMondal

IES 1998
Match ListI with ListII and select the correct answer using the codes given below the lists: ListI ListII (Measuring Device) (Parameter Measured) A. Diffraction grating 1. Small angular deviations on long flat surfaces B. Optical flat 2. Online measurement of moving B 2 parts C. Auto collimators 3. Measurement of gear pitch D. Laser scan micrometer4. Surface texture using interferometer 5. Measurement of very small displacements Code: A B C D A B C D (a) 5 4 2 1 (b) 3 5 1 2 (c) 3 5 4 1 (d) 5 4 1 2

GATE 1992
Match the instruments with the physical quantities they measure: Instrument Measurement (A) Pilottube (1) R.P.M. of a shaft g p (2) Displacement (B) McLeod Gauge (C) Planimeter (3) Flow velocity (D) LVDT (4) Vacuum (5) Surface finish (6) Area Codes:A B C D A B C D (a) 4 1 2 3 (b) 3 4 6 2 (c) 4 2 1 3 (d) 3 1 2 4

GATE 2004
Match the following Feature to be inspected Instrument P Pitch and Angle errors of screw thread 1. Auto Collimator Q Flatness error of a surface plate 2. Optical Interferometer R Alignment Ali error of f a machine hi slide lid way 3. Dividing Di idi Head H d and Dial Gauge S Profile of a cam 4. Spirit Level 5. Sine bar 6. Tool maker's Microscope (a) P6 Q2 R4 S6 (b) P5 Q2 R1 S6 (c) P6 Q4 R1 S3 (d) P1 Q4 R4 S2

GATE 1995
List I (Measuring instruments) (A) Talysurf 1. (B) Telescopic gauge 2. (C) Transfer callipers 3. (D) Autocollimator 4. Codes:A B C D (a) 4 1 2 3 (b) (c) 4 2 1 3 (d) List II (Application) Tslots Flatness Internal diameter Roughness A B C D 4 3 1 2 3 1 2 4

Page 67 of 69

11/1/2011

GATE 2010
A taper hole is inspected using a CMM, with a probe of 2 mm diameter. At a height, Z = 10 mm from the bottom, 5 points are touched and a diameter of circle (not compensated for probe size) is obtained as 20 mm. Similarly, a 40 mm diameter is obtained at a height Z = 40 mm. the smaller diameter (in mm) of hole at Z = 0 is (a) 13.334 (b) 15.334 (c) 15.442 (d) 15.542

IAS 2001
For transporting materials over long distances with greater speed, which one of the following devices is most suitable? (a) Motor vehicle (b) Industrial I d t i l vehicle hi l (c) Belt conveyor (d) Roller conveyor

IAS 1995
For moving materials is varying paths, the material handling equipments that is not suitable is (a) Crane (b) Conveyor (c) Truck (d) Hand trolley

IAS 1994
Consider the following situations 1. Loads are uniform 2. Materials move relatively continuously 3. Movement rate is variable 4. Routes do not vary For material transportation, conveyors are used when the prevailing conditions include (a) 1, 3, and 4 (b) 1, 2, and 3 (c) 1, 2, and 4 (d) 2, 3 and 4

IES 2001
During manufacture of cement, the handling of limestone is done by (a) Belt conveyor (b) Bucket conveyor (c) Overhead crane (d) Forklift crane

IAS 1998
Match ListI (Material handling equipments) with List II (Application in a foundry) and select the correct answer using the codes given below the lists: List I ListII A. Belt conveyor 1. To move the compacted mould boxes B. Monorail conveyor 2. To move the prepared moulding sand C. Apron conveyor 3. To move the rough casting to the fettling station D. Roller conveyor 4. To transfer he molten metal ladle Codes:A B C D A B C D (a) 1 2 3 4 (b) 2 1 3 4 (c) 2 4 1 3 (d) 2 4 3 1

Page 68 of 69

11/1/2011

IAS 1997
Elevators are used for moving materials (a) Along fixed and horizontal paths (b) In a vertical direction along a fixed path (c) Along a horizontal path to any distance (d) In both the planes

IES 1994
Killed steels (a) Have minimum impurity level (b) Have almost zero percentage of phosphorus and sulphur (c) Are produced by LD process (d) Are free from oxygen

IES 1992
Dye penetration method is generally used to locate (a) Core defects (b) Surface defects (c) Superficial defects (d) Temporary defects

IES 1999
Transfer machines can be defined as (a) Material processing machines (b) Material handling machines (c) Material processing and material handling machines (d) Component feeders for automatic assembly

IES 2000
AscrewthreadspecifiedbyM20x2.5CasperBIS threadsystemmeans (a) Metricthreadof20mmnominaldiameterand2.5 mmpitchhavingcoarsetolerance (b) Metric M t i thread th dof f20mmroot tdi diameter t and d2.5mm pitchhavingcoarsetolerance (c) Metricthreadoffineclasshaving20mmroot diameterand2.5mmpitch (d) Metricthreadof20mmshankdiameterand2.5mm threaddepthwithcoarsetolerance

Page 69 of 69