Scribd
Upload
9 views

3com Audlmib

3com-audlmib

Uploaded by

xsimio
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
9 views

3com Audlmib

3com-audlmib

Uploaded by

xsimio
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

--- SNMP MIB for 3Com Audit Log Service --- This SNMP MIB defines 3Com Audit

Log service parameters -A3COM-AUDL-r1-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises, IpAddress FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212; a3Com OBJECT brouterMIB OBJECT a3ComAuditLog OBJECT a3ComAudlControl a3ComAudlConfig ---CONTrol Categories a3ComAudlControlAuditTrail OBJECT-TYPE SYNTAX INTEGER { auditTrail (1), noAuditTrail (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter enables/disables the log message AuditTrail category which logs the AuditTrail messages. A default value of 2 means no AuditTrail." DEFVAL{ noAuditTrail } ::= { a3ComAudlControl 1 } a3ComAudlControlConfig OBJECT-TYPE SYNTAX INTEGER { config (1), noConfig (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter enables/disables the log message COnfig category which logs the SET/SETD/ADD/DELETE commands and other commands such as SysPassWord, SU, Login, Listen etc. The default value of 2 means no COnfig." DEFVAL { noConfig } ::= { a3ComAudlControl 2 } a3ComAudlControlMessages SYNTAX INTEGER { messages (1), noMessages (2) } ACCESS read-write STATUS mandatory OBJECT-TYPE IDENTIFIER ::= { enterprises 43 } IDENTIFIER ::= { a3Com 2 } IDENTIFIER ::= { brouterMIB 29 } OBJECT IDENTIFIER ::= { a3ComAuditLog 1 } OBJECT IDENTIFIER ::= { a3ComAuditLog 2 }

DESCRIPTION "This parameter enables/disables the log message MEssages category which log System Message and Dial History. The default value of 2 means no MEssages." DEFVAL { noMessages } ::= { a3ComAudlControl 3 } a3ComAudlControlSecurity OBJECT-TYPE SYNTAX INTEGER { security (1), noSecurity (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter enables/disables the log message SEcurity category which logs faulted set privilege, failed login and invalid community string. The default 2 means no SEcurity." DEFVAL { noSecurity } ::= { a3ComAudlControl 4 } ------Configurations LogServerAddr a3ComAudlLogServerAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "This is the IP address of a log server which has syslog daemon active with proper syslog configuration." ::= { a3ComAudlConfig 1 } ---PriorityLevel a3ComAudlPriorityLevel OBJECT-TYPE SYNTAX INTEGER { log_EMERG (1), log_ALERT (2), log_CRITICAL (3), log_ERROR (4), log_WARNING (5), log_NOTICE (6), log_INFO (7), log_DEBUG (8) } ACCESS read-write STATUS mandatory DESCRIPTION "The level is used with facility to format a priority which used as a tag in log message before sending it to syslog daemon. It also controls the log sending operation, a log message with higher Level will be be sent together with what has been in Audit Log

buffer, to a LogServerAddr immediately." DEFVAL { log_INFO } ::= { a3ComAudlConfig 2 } ---MaxLog a3ComAudlMaxLog OBJECT-TYPE SYNTAX INTEGER (1..30) ACCESS read-write STATUS mandatory DESCRIPTION "It decides the maximum number of log commands/messages could accumulate in Audit Log buffer before sending to a LogServerAddr. Value 1 means send each log without buffering." DEFVAL { 10 } ::= { a3ComAudlConfig 3 } ---IdleTime a3ComAudlIdleTime OBJECT-TYPE SYNTAX INTEGER (0..480) ACCESS read-write STATUS mandatory DESCRIPTION "This controls the idle time in minute till sending Audit log buffer if it has data. Value of 0 means this idle time is disabled." DEFVAL { 5 } ::= { a3ComAudlConfig 4 } END

You might also like