Scribd
Upload
116 views

Measurement of Building Areas

The construction area of a building is defined as the summation of all floor areas measured within the external walls or enclosing planes of the building. This includes areas such as internal stairwells, lift shafts, duct spaces, lobbies, corridors, mechanical rooms, mezzanines, covered parking, and basements. Balconies and attached structures are also included if covered and enclosed on at least two sides. Excluded areas are external steps, projecting roof overhangs over 1m, open lightwells and courtyards, uncovered ways and carports. The gross building area excludes additional internal areas such as atriums over 9m2, patios, plant boxes, sun screening, normal eaves

Uploaded by

mrlobbo
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
116 views

Measurement of Building Areas

The construction area of a building is defined as the summation of all floor areas measured within the external walls or enclosing planes of the building. This includes areas such as internal stairwells, lift shafts, duct spaces, lobbies, corridors, mechanical rooms, mezzanines, covered parking, and basements. Balconies and attached structures are also included if covered and enclosed on at least two sides. Excluded areas are external steps, projecting roof overhangs over 1m, open lightwells and courtyards, uncovered ways and carports. The gross building area excludes additional internal areas such as atriums over 9m2, patios, plant boxes, sun screening, normal eaves

Uploaded by

mrlobbo
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 0

1

Measurement of building areas


Construction area

Definition

The construction area of a building is the summation of all the areas on plan, measured at each
covered floor level over the external walls or external lines of the outermost vertical enclosing planes,
or, where applicable, the centre lines of party walls between buildings

Items to be included

Internal stairwell and staircase areas
Lift shaft areas
Duct space areas
Ground floor lobby areas
Corridor areas
Machine room and lift motor room areas
Mezzanine floor areas
Covered parking (in basements or above ground)
Basements
Finished floor areas in attic spaces
Floor areas of penthouses, staff quarters, lift motor rooms, etc
All open but covered porches, balconies and balcony corridors within the enclosing planes of the
main building
Floor areas to attached sheds, carports, etc and all partially completed rooms, porches, balconies,
etc provided the relevant areas are covered and have at least two of their walls not less than two
thirds the height of the wall common to the main building
Corridors to multi-storey flats (apartments)

Items to be excluded

External steps and paved areas
Areas of projecting roof overhangs, hoods, canopies and the like not exceeding 1m
Enclosed open areas (light or ventilation wells and courtyards)
Areas of open covered ways and carports, etc
Areas of unenclosed fire escapes
Areas on plan of small projections such as pilasters, attached piers, fins, chimney breasts, etc

Gross building area

Certain local authorities have their own definition of gross building area (sometimes referred to as
floor space). It is important to check the applicable local authorities definition against the definition
below

Definition

The gross building area covers the entire building area, but excludes the following items:
Internal atriums, light wells, etc in excess of 9 m
Patios

Plant boxes
Sun screening
Normal eaves projections (but not excessive eaves projections)
Escape stairs
Internal uncovered areas
Floor areas, including basement storeys (any storey with a floor level at least 2m lower than the
average level of the land around the building), reserved exclusively for the parking of vehicles
Machine rooms, lift motor rooms, service rooms, caretakers flats, etc
Balconies, terraces, etc

The gross building area is mainly used by planning consultants to plan a building in accordance with
the permissible floor area ratio (FAR)/ floor space ratio (FSR). The exact definition may vary from
one local authority to the next

Sectional title area (South Africa)

The sectional title area is the area of the unit (excluding the common property) measured to the
median line of the boundary walls of each section and to the median line of the external walls

Rentable area and usable area (South Africa)

Refer to the Method for Measuring Floor Areas in Buildings published by the South African Property
Owners Association (SAPOA) for the definition of rentable area and useable area. Go to Further
sources of property data for a link to the website of the South African Property Owners Association

You might also like