Scribd
Upload
11K views

Lifting Beam Calculation

This document provides design calculations for lifting lugs on a lifting beam for an offshore oil platform. It includes input parameters like beam dimensions, material properties, and load cases. The output calculations determine stresses in the lugs and beam, including tensile, shear, bending and compressive stresses, to verify they are below allowable limits. All stresses were found to be acceptable for the given load conditions.

Uploaded by

ராபர்ட் ஆன்றோ ரெனி
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
11K views

Lifting Beam Calculation

This document provides design calculations for lifting lugs on a lifting beam for an offshore oil platform. It includes input parameters like beam dimensions, material properties, and load cases. The output calculations determine stresses in the lugs and beam, including tensile, shear, bending and compressive stresses, to verify they are below allowable limits. All stresses were found to be acceptable for the given load conditions.

Uploaded by

ராபர்ட் ஆன்றோ ரெனி
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 2

Project No: Client: Project : Package Desc:

1110
SBM / ESSO EXPLORATION ANGOLA (BLOCK 15) LTD KIZOMBA C- FPSO SAXI BATUQUE TEG REGENERATION SYSTEM -A-T7210

LIFTING BEAM
See Detail H1 Do T L T1 R3 D1 H1 T2 D2

W1

Lug Detail (Typ. Top and Bottom) INPUTDATA


Length between Lugs Thickness of Lug Plate Thickness of Cheek Plate Hole Diameter Diameter of Cheek Plate Width of Lug Plate Max. Sling Tension in under Spreader bar sling Sling Tension in the pair sling of Maximum tension sling Inclination of the maximum tension sling with base Inclination of the other sling with base Max. Vertical Load at Lifting Beam Lug(Underslung) (F1 x Sinq1 +F2 x Sinq2) Max. Sling Tension in above spreader bar sling Inclination of the sling with spreader bar Max. Vertical Load at Lifting Beam Lug(On-top Lugs) (F3 x Sinq t) Max. Horizontal Load at Lifting Beam Lug (On-top Lugs) (F3 x Cosqt) Max. Out-of-plane Load at Lifting Beam Lug (On-top Lugs) Horizontal Force in Beam Pin Diameter of Selected Shackle Height of Lug Hole above Lifting Beam Pipe Outside Diameter Nominal Pipe Thickness Pipe Inside Diameter Beam Modulus of Elasticity Yield stress L T1 T2 D1 D2 W1 F1 F2 q1 q2 Fsu = = = = = = = = = = = 5930 25 15 74 220 400 213.79 233.65 68.45 70.9 419.63 mm mm mm mm mm mm kN kN kN

F3 qt Fst

= = =

484.34 64.83 438.35

kN kN

Fsh

205.99

kN

Fso Fh Dp H1 D0 T3 Di E fy

= = = = = = = = =

24.22 234.13 69.85 150 273 13 247 205000 250

kN kN mm mm mm mm mm N/mm2 N/mm2

Project No: Client: Project : Package Desc:

1110
SBM / ESSO EXPLORATION ANGOLA (BLOCK 15) LTD KIZOMBA C- FPSO SAXI BATUQUE TEG REGENERATION SYSTEM -A-T7210

OUTPUT DATA Underslung Lugs on Lifting Beam Tensile Stress in Plate (Fsu/(( W1-D1)xT1)) Shear Stress in Plate Fsu/((R3^2-(d1/2)^2)^0.5 x 2 x T1) Bearing Stress at Hole Fsu/((T1 + 2 x T2) x Dp) On-Top Lugs on Lifting Beam Tensile Stress in Plate (Fst/(( W1-D1)xT1)) Shear Stress in Plate Fst/((R3^2-(d1/2)^2)^0.5 x 2 x T1) Bending Stress at Hole Fst/((T1 + 2 x T2) x Dp) Bending Stress in Plate(In-plane) (Fsh x H1) / (T1 x W1^2/6) Bending Stress in Plate(Out-of-plane) (Fs0 x H1) / (W1 x T1^22/6) Lifting Beam Cross Sectional Area of Beam ( p x (Do^2-Di^2)/4 Moment of Inertia of Beam ( p x (Do^4-Di^4)/64 Axial Compressive Stress in Beam Maximum Allowable Compressive Load in Beam ( p^2 x E x I/L^2) Clearly all the above stresses are acceptable CSA = 10619 mm2 ft = 53.79 N/mm2 ft = 51.49 N/mm2

fs

42.70

N/mm2

fp

109.23

N/mm

fs

44.61

N/mm2

fp

114.10

N/mm2

fb

46.35

N/mm2

fbo

87.18

N/mm2

89951345

mm4

fc P

= =

22.05 5175495

N/mm2 N

You might also like