Scribd
Upload
82 views

Emergency Light

This circuit uses AA batteries to power an emergency light or alarm that is automatically activated when mains power is lost, and it can be latched to remain on when power is restored; it has options to illuminate a light bulb or sound an alarm using transistors, resistors, capacitors, and other components connected to a mains power supply for battery charging. The purpose is to provide emergency lighting or alert during power outages.

Uploaded by

gizmodeek
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
82 views

Emergency Light

This circuit uses AA batteries to power an emergency light or alarm that is automatically activated when mains power is lost, and it can be latched to remain on when power is restored; it has options to illuminate a light bulb or sound an alarm using transistors, resistors, capacitors, and other components connected to a mains power supply for battery charging. The purpose is to provide emergency lighting or alert during power outages.

Uploaded by

gizmodeek
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Emergency Light & Alarm

Powered by two AA NI-CD batteries


Four switchable options

Circuit diagram:

Parts:
R1____________220K 1/4W Resistor
R2____________470R 1/2W Resistor
R3____________390R 1/4W Resistor
R4______________1K5 1/4W Resistor
R5______________1R 1/4W Resistor
R6_____________10K 1/4W Resistor
R7____________330K 1/4W Resistor
R8____________470R 1/4W Resistor
R9____________100R 1/4W Resistor

C1____________330nF 400V Polyester Capacitor


C2_____________10µF 63V Electrolytic Capacitor
C3____________100nF 63V Polyester Capacitor
C4_____________10nF 63V Polyester Capacitor

D1-D5________1N4007 1000V 1A Diodes


D6______________LED Green (any shape)
D7___________1N4148 75V 150mA Diode

Q1,Q3,Q4______BC547 45V 100mA NPN Transistors


Q2,Q5_________BC327 45V 800mA PNP Transistors
SW1,SW2________SPST Switches
SW3____________SPDT Switch

LP1____________2.2V or 2.5V 250-300mA Torch Lamp Bulb

SPKR___________8 Ohm Loudspeaker

B1_____________2.5V Battery (two AA NI-CD rechargeable cells wired in


series)

PL1____________Male Mains plug

Device purpose:

This circuit is permanently plugged into a mains socket and NI-CD batteries are trickle-
charged. When a power outage occurs, the lamp automatically illuminates. Instead of
illuminating a lamp, an alarm sounder can be chosen.
When power supply is restored, the lamp or the alarm is switched-off. A switch provides
a "latch-up" function, in order to extend lamp or alarm operation even when power is
restored.

Circuit operation:

Mains voltage is reduced to about 12V DC at C2's terminals, by means of the reactance
of C1 and the diode bridge (D1-D4). This avoids the use of a mains transformer.
Trickle-charging current for the battery B1 is provided by the series resistor R3, D5 and
the green LED D6 that also monitors the presence of mains supply and correct battery
charging.
Q2 & Q3 form a self-latching pair that start operating when a power outage occurs. In
this case, Q1 biasing becomes positive, so this transistor turns on the self latching pair.
If SW3 is set as shown in the circuit diagram, the lamp illuminates via SW2, which is
normally closed; if set the other way, a square wave audio frequency generator formed by
Q4, Q5 and related components is activated, driving the loudspeaker.
If SW1 is left open, when mains supply is restored the lamp or the alarm continue to
operate. They can be disabled by opening the main on-off switch SW2.
If SW1 is closed, restoration of the mains supply terminates lamp or alarm operation, by
applying a positive bias to the Base of Q2.

Notes:

• Close SW2 after the circuit is plugged.


• Warning! The circuit is connected to 230Vac mains, then some parts in the circuit
board are subjected to lethal potential!. Avoid touching the circuit when plugged
and enclose it in a plastic box.

This circuit was awarded with publication in ELECTRONICS WORLD "Circuit


Ideas", September 2001 issue, page 708.
Having Questions?

You might also like