University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.

html

Harmonic Analysis of a Cantilever Beam

Introduction
This tutorial was created using ANSYS 7.0 The purpose of this tutorial is to explain the steps required to perform Harmonic analysis the cantilever beam shown below.

We will now conduct a harmonic forced response test by applying a cyclic load (harmonic) at the end of the beam. The frequency of the load will be varied from 1 - 100 Hz. The figure below depicts the beam with the application of the load.

ANSYS provides 3 methods for conducting a harmonic analysis. These 3 methods are the Full , Reduced and Modal Superposition methods.

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

This example demonstrates the Full method because it is simple and easy to use as compared to the other two methods. However, this method makes use of the full stiffness and mass matrices and thus is the slower and costlier option.

Preprocessing: Defining the Problem

The simple cantilever beam is used in all of the Dynamic Analysis Tutorials. If you haven't created the model in ANSYS, please use the links below. Both the command line codes and the GUI commands are shown in the respective links.

Solution: Assigning Loads and Solving

1. Define Analysis Type (Harmonic) Solution > Analysis Type > New Analysis > Harmonic
ANTYPE,3

2. Set options for analysis type:

Select: Solution > Analysis Type > Analysis Options.. The following window will appear

As shown, select the Full Solution method, the Real + imaginary DOF printout format and do not use lumped mass approx. Click 'OK' The following window will appear. Use the default settings (shown below).

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

3. Apply Constraints

Select Solution > Define Loads > Apply > Structural > Displacement > On Nodes The following window will appear once you select the node at x=0 (Note small changes in the window compared to the static examples):

Constrain all DOF as shown in the above window

4. Apply Loads:

Select Solution > Define Loads > Apply > Structural > Force/Moment > On Nodes Select the node at x=1 (far right) The following window will appear. Fill it in as shown to apply a load with a real value of 100 and an imaginary value of 0 in the positive 'y' direction

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

Note: By specifying a real and imaginary value of the load we are providing information on magnitude and phase of the load. In this case the magnitude of the load is 100 N and its phase is 0. Phase information is important when you have two or more cyclic loads being applied to the structure as these loads could be in or out of phase. For harmonic analysis, all loads applied to a structure must have the SAME FREQUENCY. 5. Set the frequency range

Select Solution > Load Step Opts > Time/Frequency > Freq and Substps... As shown in the window below, specify a frequency range of 0 - 100Hz, 100 substeps and stepped b.c..

By doing this we will be subjecting the beam to loads at 1 Hz, 2 Hz, 3 Hz, ..... 100 Hz. We will specify a stepped boundary condition (KBC) as this will ensure that the same amplitude (100 N) will be applyed for each of the frequencies. The ramped option, on the other hand, would ramp up the amplitude where at 1 Hz the amplitude would be 1 N and at 100 Hz the amplitude would be 100 N. You should now have the following in the ANSYS Graphics window

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

6. Solve the System Solution > Solve > Current LS

SOLVE

Postprocessing: Viewing the Results

We want to observe the response at x=1 (where the load was applyed) as a function of frequency. We cannot do this with General PostProcessing (POST1), rather we must use TimeHist PostProcessing (POST26). POST26 is used to observe certain variables as a function of either time or frequency. 1. Open the TimeHist Processing (POST26) Menu Select TimeHist Postpro from the ANSYS Main Menu. 2. Define Variables In here we have to define variables that we want to see plotted. By default, Variable 1 is assigned either Time or Frequency. In our case it is assigned Frequency. We want to see the displacement UY at the node at x=1, which is node #2. (To get a list of nodes and their attributes, select Utility Menu > List > nodes).

Select TimeHist Postpro > Variable Viewer... and the following window should pop up.

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

Select Add (the green '+' sign in the upper left corner) from this window and the following window should appear

We are interested in the Nodal Solution > DOF Solution > Y-Component of displacement. Click OK.

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

Graphically select node 2 when prompted and click OK. The 'Time History Variables' window should now look as follows

3. List Stored Variables

In the 'Time History Variables' window click the 'List' button, 3 buttons to the left of 'Add' The following window will appear listing the data:

4. Plot UY vs. frequency

In the 'Time History Variables' window click the 'Plot' button, 2 buttons to the left of 'Add'

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

The following graph should be plotted in the main ANSYS window.

Note that we get peaks at frequencies of approximately 8.3 and 51 Hz. This corresponds with the predicted frequencies of 8.311 and 51.94Hz. To get a better view of the response, view the log scale of UY.

Select Utility Menu > PlotCtrls > Style > Graphs > Modify Axis The following window will appear

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

As marked by an 'A' in the above window, change the Y-axis scale to 'Logarithmic' Select Utility Menu > Plot > Replot You should now see the following

Copyright 2001 University of Alberta

University of Alberta ANSYS Tutorials - www.mece.ualberta.ca/tutorials/ansys/IT/Harmonic/Harmonic.html

This is the response at node 2 for the cyclic load applied at this node from 0 - 100 Hz.

For ANSYS version lower than 7.0, the 'Variable Viewer' window is not available. Use the 'Define Variables' and 'Store Data' functions under TimeHist Postpro. See the help file for instructions.

Copyright 2001 University of Alberta