DIGITAL SYSTEM BENM 2133

CHAPTER 1 LATCHES & FLIP-FLOPS

Outcome
!! After learning this chapter, student should be able to; "! Recognize the difference between latches and flipflops "! Analyze the operation of the flip flop "! Draw the output timing diagram (waveform) for single and combination of latches and flip-flops "! Troubleshoot basic flip-flops circuits

FKEKK

DIGITAL SYSTEM BENM 2133

Terminology
#! Multivibrator A class of digital circuits in which the output is connected back to the input (i.e. it is fed back to the input, commonly referred to as feedback) to produce either two stable states, one stable state, or no stable states, depending on the configuration. Bistable Having two stable states. Latches and flip-flops are bistable multivibrators Latch An asynchronous bistable multivibrator, used for storing 1 bit Flip-Flop A synchronous bistable multivibrator, used for storing 1 bit

#!

#! #!

Teminology (continue..)
!! Asynchronous
There is no fixed timing relationship

!! Synchronous
There is a fixed timing relationship, usually through the use of a clock pulse

!! Edge-triggered Flip-Flop
A type of flip-flop in which the input data are entered and appear on the output on the same clock edge, either the positive or negative edge

FKEKK

DIGITAL SYSTEM BENM 2133

Introduction: Comparison between combinational circuits and sequential circuits

!! Characteristics of combinational circuits are; "! "! "! "! Output depends only to current input No feedback from output of the system Unable to remember past values Logic gates AND, OR, XOR, NOT

Introduction (continue..)

FKEKK

DIGITAL SYSTEM BENM 2133

Introduction (continue..)
!! Multivibrator any digital circuit employing feedback. !! Sequential/Multivibrator devices are categorized as; "! Bistable $! Two stable states, SET and RESET $! Latches and flip-flops "! Monostable $! Has one stable state $! Timer "! Astable $! No stable state $! Oscillator (to generate periodic pulse waveforms for timing purposes. )
Fig: inverter with feedback
7

Latches
!! Latches are bistable multivibrator !! A two stable states digital circuit that produces HIGH or LOW depending on the input !! For gated (enabled) latches, the output are controlled by the enable (EN) input !! It is level triggered, means that any input changes during the EN is active, the output will be affected !! The operation will be observed by examining the timing diagram

FKEKK

DIGITAL SYSTEM BENM 2133

Latches (continue..)
Four types; "! S-R latch "! S-R latch

"! Gated S-R latch

"! Gated D latch

S-R (Set-Reset) Latch

Logic circuit Symbol

Truth table

10

FKEKK

DIGITAL SYSTEM BENM 2133

S-R Latch Timing Diagram

11

S-R (Set-Reset) Latch

Logic circuit Symbol

Truth table

12

FKEKK

DIGITAL SYSTEM BENM 2133

S-R Latch Timing Diagram

13

Gated S-R Latch

Logic circuit Symbol

Truth table

14

FKEKK

DIGITAL SYSTEM BENM 2133

Gated S-R Latch Timing Diagram

15

Gated D latch
Logic circuit Symbol

Truth table

16

FKEKK

DIGITAL SYSTEM BENM 2133

Gated D Latch Timing Diagram

17

How does S-R latch works?

!! By using DeMorgans Theorem

NAND gate

Negative-OR gate

!! The equivalent logic circuit

18

FKEKK

DIGITAL SYSTEM BENM 2133

How does S-R latch works? (continue..)

!! Assume that S = 0 and R = 1, therefore Q = 1 and Q = 0

!! Change both S and R to 1, therefore both Q and Q are still the same as previous value

19

How does S-R latch works? (continue..)

!! Now, change S = 1 and R = 0, therefore Q = 0 and Q = 1

!! Change both S and R to 1, therefore both Q and Q are still the same as previous value

20

FKEKK

10

DIGITAL SYSTEM BENM 2133

How does S-R latch works? (continue..)

!! Now, set both input to 0, hence, both Q and Q are 1 which is invalid

!! This state should be avoided since the changing state from invalid is unpredictable. Prove it!!!

21

Gated D Latch Exercises

22

FKEKK

11

DIGITAL SYSTEM BENM 2133

Latch applications
! SR and D latches are among the simplest and least expensive types of memory elements used in logic circuits.

Fig: Typical use of latches in a computers input/output circuits

23

Edge-Triggered Flip-Flops
!! Flip-flops are synchronous bistable multivibrator. !! Synchronous means the output changes state only occur at a triggering point called clock !! Edge-triggered can be either positive (rising) edge or negative (falling) edge of the clock !! Edge triggered flip-flops change state either at positive or negative clock !! Clock input for flip-flops

24

FKEKK

12

DIGITAL SYSTEM BENM 2133

Edge-Triggered Flip-Flops (continue..)

!! Four types; "! S-R flip flops
Positive-edge triggered Negative-edge triggered

"! D flip-flops

"! J-K flip-flops

"! T flip-flops

25

Edge-Triggered S-R Flip-Flop

!! Positive-edge S-R FF

26

FKEKK

13

DIGITAL SYSTEM BENM 2133

Edge-Triggered S-R Flip-Flop Exercises

27

Edge-Triggered D Flip-Flop
!! Positive-edge D FF

28

FKEKK

14

DIGITAL SYSTEM BENM 2133

Edge-Triggered D Flip-Flop Exercises

29

Edge-Triggered J-K Flip-Flop

!! Positive-edge J-K FF

30

FKEKK

15

DIGITAL SYSTEM BENM 2133

Edge-Triggered J-K Flip-Flop Exercises

31

Edge-Triggered T Flip-Flop
!! Positive-edge T FF

32

FKEKK

16

DIGITAL SYSTEM BENM 2133

Edge-Triggered T Flip-Flop Exercises

33

Latch and Flip-Flop Exercise

Draw the output waveform for the JK flip flop and D latch whose input are as given

34

FKEKK

17

DIGITAL SYSTEM BENM 2133

Master Slave Flip-Flops

!! Introduced to overcome timing problem that might be occurred to flip-flop !! Two similar flip-flops are connected with different clock !! The output is stable even though input changes

Qo

Q1

35

Asynchronous Preset and Clear

!! Most integrated circuit FF have asynchronous inputs !! These input change the FF output without clock triggering !! Normally label as preset (PRE) and clear (CLR) !! For example, take the T FF
/PRE 0 0 1 1 /CLR 0 1 0 1 OUTPUT Invalid Q = 1 (Set) Q = 0 (Reset) Flip-flop normal operation

36

FKEKK

18

DIGITAL SYSTEM BENM 2133

Flip-Flop Operating Characteristics

!! Propagation Delay Times "! Required time interval for output signal to occur after an input signal has been applied
CLK Q tPHL
50%

CLK Q tPLH

!! Set-up Time "! Minimum time interval for the signal to retain the value before clock pulse is triggered
D CLK ts 37

Flip-Flop Operating Characteristics

!! Hold time "! Minimum time interval for the signal to retain the value after clock pulse is triggered
CLK D th

!! Maximum Clock Frequency "! Highest rate at which a flip-flop can respond to the input signal
fmax

38

FKEKK

19

DIGITAL SYSTEM BENM 2133

Flip-Flop Operating Characteristics (continue..)

!! Pulse Width "! Minimum clock pulse width is smallest time between HIGH and LOW !! Power Dissipation "! Total power consumption of the flip-flops "! For example, a 7474 chip has two D flip-flops which each of the flip-flop operates at +5Vdc and draws 5mA $! P = Vcc x Icc = 5 x 5 = 25mW $! PT = 2 x 25 mW = 50mW $! I = 50mW/5V = 10mA $! Therefore, the chip must be supplied by +5Vdc supply with at least 10mA of current.

39

Flip-Flop Applications

!! Parallel data storage !! You will learn more in Chapter 3

40

FKEKK

20

DIGITAL SYSTEM BENM 2133

Flip-Flop Applications (continue..)

!! Frequency division

41

Flip-Flop Applications (continue..)

!! Counting !! You will learn more in Chapter 2

42

FKEKK

21

DIGITAL SYSTEM BENM 2133

Exercises
(a)! What is the difference between latch and flip-flop operation? (b)! List 3 applications of flip-flops. Explain briefly each of the application of the flipflops. (c)! Give the definition and describe the propagation delay time in flip-flop operating characteristics.
43

Exercises (Continue)
(d) For negative edge triggered J-K flip-flop with preset (/PRE) and (/ CLR) inputs, determine the Q output for the input shown in the timing diagram in Figure Q1(d). Assume Q starts with 1 and the input J and K always 1.

44

FKEKK

22