Scribd
Upload
886 views

Circular Hollow Concrete Column

The document provides design specifications for a circular hollow concrete column according to Chinese standard GB 50010-2002. It lists the dimensions and material properties of the column, including its outer diameter, wall thickness, rebar size and grade, concrete strength, load applied, and other parameters. It then outlines the equations to calculate the interaction ratio, eccentricity, sectional curvature coefficients, and other factors to design the column according to the standard.

Uploaded by

Uttam Kumar Ghosh
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
886 views

Circular Hollow Concrete Column

The document provides design specifications for a circular hollow concrete column according to Chinese standard GB 50010-2002. It lists the dimensions and material properties of the column, including its outer diameter, wall thickness, rebar size and grade, concrete strength, load applied, and other parameters. It then outlines the equations to calculate the interaction ratio, eccentricity, sectional curvature coefficients, and other factors to design the column according to the standard.

Uploaded by

Uttam Kumar Ghosh
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

Design of circular hollow concrete column as per Chinese Standard GB 50010-2002

Outer diameter of column do =h (mm)= Inner diameter of column di (mm)= Factored compressive force on column bottom N (kN)= Factored bending moment at column bottom M (kN-m)= Clear cover of rebars (mm)= Effective length of column L0 (mm)= Grade of concrete = Yield stress of rebars fy (Mpa)= Young modulus of rebars Es (Mpa)= Percentage of rebars considered = Diameter of vertical rebars (mm)= Diameter of stirrups (mm)= Design value of axial compressive strength of concrete fc (Mpa)= Lo/d0= Stability coefficient of rebars =1/*1+0.002*(L0/d0-8)^2+= Area of concrete section A (mm2)= Interaction ratio of column for compression only Uc= Eccentricity due to bending moment e0=M/N (mm)= Additional eccentricity as per clause no. 7.3.3 (mm)= Total eccentricity ei=e0+ea equation 7.3.7-6(mm)= Corrected coefficient for sectional curvature of eccentric compression member as per clause no 7.3.10 1=max(1, 0.5*fc*A/N)= Influence co-efficient considering the influence of slenderness ratio of member on sectional curvature as per clause no 7.3.10 2=if(Lo/h<15, 1, (1.15-0.01*L0/h)= Outer radius of column r2 (mm)= Inside radius of column r1 (mm)= Radius of circumference where the centroid of longitudinal ordinary steel reinforcements situated rs (mm)= Effective depth of section h0 (mm)= Eccentricity enhancement coefficient as per clause no 7.3.10 =1+1*2*(1/(1400ei/ho)*(Lo/h)^2= 1= t=1-1.5 (equation 7.3.7.5) The following two equations are to be solved to determine N**1*fc*A+(-1)fy*As+ --------------------------equation 7.3.7-1 N**ei*1*fc*A(r1+r2)*(Sin/2)+fy*As*rs*(Sin+Sint)/+------------------equation 7.3.7-2 t=1-1.5* Putting the value of As & t from the above equations to 7.3.7-2 we get, *1*fc*A(r1+r2)*(Sin/2)+fy**(N-*1*fc*A)/((t)*fy)+*rs*(Sin+Sin(1-1.5))/+-N**ei0 2400 2040 2925 4408 30 79200 C30 360 200000 0.8 25 8 14.3 33 0.44 1255380 0.16 1507.0 80.0 1587.0 1

fc

Design values of concrete (Table 4.1.4) C20 C25 C30 C35 C40 C45 9.6 11.9 14.3 16.7 19.1 21.1

C50 23.1

0.82

1200 1020 1149.5 2349.5 1.94

= From equation 7.3.7-1, As=(N-*1*fc*A)/((-t)*fy)=

0.277 18371

1 of 1

You might also like