VDR-100G2/G2S Operation User Manual

RUT-UM-02-002 Rev.1.8

Rutter Technologies Inc 70 Brookfield Road St. Johns, NL Canada A1E 3T9 Tel: (709) 368-4213 Fax: (709) 368-1337 www.ruttertech.com

Rutter Technologies Inc. VDR-100G2/G2S Operation User Manual RUT-UM-02-002 Rev.1.8 Revision Issue Date: 15 February 2007 Regional Offices Germany Joseph-Hayden Str 20 D 28209 Bremen, Germany Tel: +49 421 34 99 538 Fax: +49 721 151 329 560 [email protected] Greece nd 17, Voulis Street (2 Floor) 105 63 Syntagma, Athens Greece Tel: +30 210 323 6935 Fax: +30 210 322 0643 [email protected] Italy Rutter Technologies Inc. - European Office Viale Boccaccio 111 50053 Empoli Italy Tel: +39 0571 945099 Fax: +39 0571 945406 [email protected] Sweden Rutter Technologies Inc. Lered 111 SE 274 92 Skurup Sweden Tel: +46 706 386 396 Fax: +46 706 143 143 [email protected]

The Rutter Technologies Worldwide Service List is available for download in PDF format at the following web site address: http://www.ruttertech.com/support/
Copyright Rutter Technologies Inc All rights reserved. This document contains CONFIDENTIAL information that is PROPRIETARY to Rutter Technologies Incorporated. This commercially sensitive information is being provided to the recipient solely for the purpose specified and shall not be reproduced, disclosed or supplied, in whole or in part, to any other person without the prior written consent of Rutter Technologies Inc. Although every precaution has been taken in the preparation of this manual, Rutter Technologies Inc assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of information contained herein.

This page is intentionally blank.

Table of Contents
1 SYSTEM ..................................................................................................... 1
1.1
1.1.1 1.1.2 1.1.3 1.1.4 1.1.5 1.1.6 1.1.7 1.1.8 1.1.9

VDR-100G2 System Components ............................................................................................ 1

Data Processing Unit (DPU) ........................................................................................................................................3 Data Acquisition Unit (DAU).........................................................................................................................................4 Audio Module ...............................................................................................................................................................5 Video Module ...............................................................................................................................................................7 NMEA Input Modules ...................................................................................................................................................8 Operation & Alarm Unit (OAU).....................................................................................................................................9 Final Recording Medium (FRM/SFRM)......................................................................................................................10 Remote Storage Module (RSM).................................................................................................................................13 External Data Interfaces ............................................................................................................................................13

1.2
1.2.1

Client / Playback PC ................................................................................................................ 14

Minimum Requirements .............................................................................................................................................14

1.3

System Overview Drawings.................................................................................................... 15

2 3

TECHNICAL SPECIFICATIONS ................................................................. 17 USER GUIDE ............................................................................................ 21

3.1 3.2 3.3 3.4 3.5 3.6 3.7 Securing Data........................................................................................................................... 21 Viewing Secured Data ............................................................................................................. 21 Securing Data to the RSM.......................................................................................................22 Muting Audible Alarm.............................................................................................................. 22 Dimming the Display ............................................................................................................... 22 Test Screen .............................................................................................................................. 22 Alarm Code Description.......................................................................................................... 22

DATA RETRIEVAL .................................................................................... 25

4.1 4.2
4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.7

Optional Client Download PC ................................................................................................. 25 Installation of Download Software......................................................................................... 26

Starting the Download Process..................................................................................................................................27 Begin the Download...................................................................................................................................................27 Download Secured Data Set......................................................................................................................................29 Extended NMEA Download .......................................................................................................................................30 Complete vs. Partial Download..................................................................................................................................30 Error Log and Battery Log..........................................................................................................................................31 Disconnecting from the VDR......................................................................................................................................31

4.3 4.4

USB Memory Stick................................................................................................................... 31 Remote Storage Module..........................................................................................................31

RSM & USB Memory Stick ....................................................................... 33

5.1
5.1.1 5.1.2 5.1.3 5.1.4

Copying Data to RSM/USB Memory Stick ............................................................................. 34

Copy Current Data .....................................................................................................................................................35 Copying Secured Data...............................................................................................................................................35 Copying Extended NMEA Data..................................................................................................................................36 Disconnecting the RSM .............................................................................................................................................36

5.2

Connecting Client PC to RSM................................................................................................. 37

PLAYBACK SOFTWARE ............................................................................ 39

6.1 6.2
6.2.1

Playback Installation - Client PC............................................................................................ 39 Starting the Playback Application ......................................................................................... 40

Configuration File.......................................................................................................................................................40

6.3

Choosing Data for Playback ................................................................................................... 41

VDR-100G2/G2S Operation Manual

TOC - I

6.3.1

Unarchive Extracted Data ..........................................................................................................................................42

6.4 6.5 6.6 6.7 6.8 6.9

6.9.1 6.9.2

Enabling Ethernet Broadcasts ............................................................................................... 43 Starting the Playback .............................................................................................................. 43 Passwords ................................................................................................................................ 44 Playback Controls ................................................................................................................... 44 Audio Volume & Channel Selection....................................................................................... 45 Conning Tab Screen................................................................................................................ 46
Depth Graph ..............................................................................................................................................................46 Wind Information........................................................................................................................................................47

6.10
6.10.1 6.10.2 6.10.3

AIS Playback Tab Screen........................................................................................................ 49

Targets .......................................................................................................................................................................49 View Settings .............................................................................................................................................................50 GuardZone.................................................................................................................................................................51

6.11 6.12 6.13 6.14 6.15 6.16

6.16.1 6.16.2

Fire Doors Tab Screen ............................................................................................................ 51 Water Doors Tab Screen .........................................................................................................52 Hull Openings Tab Screen ...................................................................................................... 53 Log Tab Screen........................................................................................................................ 53 Alarms Tab Screen .................................................................................................................. 54 Data Extraction ........................................................................................................................ 54
Open Extraction Window ...........................................................................................................................................54 Selecting Data for Extraction .....................................................................................................................................55

6.17

Closing the Application........................................................................................................... 55

VDR-100G2/G2S Operation Manual

TOC - II

1
1.1

SYSTEM
VDR-100G2 System Components

The VDR-100G2 is a modular, Ethernet-based data acquisition and storage system. It is designed to collect and maintain a secure, retrievable record of information related to the position, movement, physical status, and command & control of a marine vessel. While this manual references the VDR-100G2, it is also applicable to the Simplified Voyage Data Recorder (VDR-100G2S) unless otherwise stated. There are three (3) types of information recorded by a Voyage Data Recorder (VDR): 1. Audio data acquired from microphones mounted in the immediate vicinity of a vessels main bridge workstations and a primary VHF radio is required to be recorded. The VDR-100G2 has the capability to record public address systems, internal communications, additional radios, or other areas of the ship if necessary. 2. Video data can be captured at 15 second intervals from one (1) complete radar video frame screen via a dedicated buffered output port of the radar. The VDR-100G2 can record images captured from multiple Radars, electronic chart, or CCTV displays at various capture intervals. An SVDR is not required to capture video data. 3. ASCII serial data related to the position, heading, speed, wind, water depth, hull openings, bulkhead doors, alarm status, manoeuvring commands, and responses can be recorded with the VDR-100G2. The standard format for this data is defined in the NMEA 0183/IEC 61162 standards; through the implementation of an interface module, non-standard data can be converted to this format. For a complete list of data items to be recorded, refer to IEC 61996. The VDR-100G2 is a fully IMO compliant VDR. The base system consists of the following components: 1. Data Processing Unit (DPU), consisting of: Data Management Module (DMM) Power Supply Module Power Control Module 2 x 28Ah 12V batteries Cooling Fan with thermostat 4-Port Ethernet switch 4GB USB Memory Stick Data Acquisition Unit (DAU)*, consisting of: 4-Channel Audio Module 1-Channel Video Module 8-Channel NMEA Module

2.

* The DAU is optional with the VDR-100G2S. 3. 4. 5. Operation & Alarm Unit (OAU) Final Recording Medium (FRM) Internal and External Microphones

VDR-100G2/G2S Operation Manual

Optionally, the VDR-100G2 can also be supplied with the following components: 1. 2. 3. 4. 2 or 4 additional audio channels (to a maximum of 16 inputs) 1, 2, or 3 additional video channels (to a maximum of 4) 8 or 16 NMEA channels Remote Storage Module (RSM) (implemented for long term archiving and/or additional data backup storage retrieval) 5. Data Interfaces (implemented for the conversion of non-standard signals to NMEA format). Interfaces include:

DataAnalog DataDiscrete DataSynchro DataGyro DataProtocol

DATA ACQUISITION UNIT

DATA PROCESSING UNIT

Figure 1.1 - VDR-100G2 Block Diagram

The VDR-100G2S has many similar components to the VDR-100G2, with the following differences:

The Video Module is only required if the vessels radar has an available COTS (commercial offthe-shelf) interface. Therefore, the recording of video data may not be applicable in some VDR100G2S installations. The VDR-100G2S has an accompanying Simplified FRM (SFRM) capsule.

VDR-100G2/G2S Operation Manual

1.1.1

Data Processing Unit (DPU)

The Data Processing Unit (DPU) receives and processes information provided from the various Audio, Video, and NMEA Input Modules. This information is processed in the Data Management Module (DMM) for archiving on the DMMs internal hard drive, the Final Recording Medium (FRM), USB Memory Stick, and the optional Remote Storage Module (RSM). The VDR-100G2 power system is housed in the DPU, and accepts universal AC or 24VDC from the ships emergency power while providing 24VDC to the VDR-100G2 modules. The power system includes batteries to provide uninterrupted power to the audio recording system in the event of a blackout. The DPU also contains an Ethernet switch (hub) which provides the ability to combine video and NMEA data into a single Ethernet link.

Figure 1.2 - Data Processing Unit

1.1.1.1 Data Management Module The Data Management Module (DMM) is a rugged, small form factor Pentium computer. It is equipped with four (4) Ethernet input ports, two (2) serial ports, two (2) USB ports, a high capacity hard disk drive, and a compact flash card containing an embedded Windows XP operating system. The module compresses and stores data received from the acquisition modules and, simultaneously, outputs processed data to the FRM, USB Memory Stick, optional Remote Storage Module (RSM), and optional Download/Playback PC (as described below). Communication with the Operation and Alarm Unit (OAU) and Power Control Module (PCM) occurs via the serial ports. Additionally, the DMM can be configured to provide data for real-time display via an Ethernet connection. In addition to the most current data set, the base model DMM can store numerous previously recorded full data sets in a secure location. This secure location prevents previously recorded data sets from being overwritten.

VDR-100G2/G2S Operation Manual

Figure 1.3 - Data Management Module (Rear View)

1.1.1.2 Power Supply Module The VDR-100G2 has the option of being powered by either AC or DC supply (must be chosen at time of order as it is not field configurable):

The AC input range is 85-264V, 47-63Hz. The DC input range is 19-28V. The output of both supplies is 27.6VDC, which is the normal operating voltage of the VDR.

The power supply also acts as a battery charger for re-charging low batteries or maintaining a full charge. The battery input is reverse polarity protected by a crossbar diode and a replaceable fuse. 1.1.1.3 Power Control Module The Power Control Module monitors the power system and communicates the power system status information to the DMM. It also controls the switching circuitry to transfer the load from the power supply to the batteries.

1.1.2

Data Acquisition Unit (DAU)

The Data Acquisition Unit (DAU) is an optional component that can house up to four (4) main data acquisition modules:

Audio Module Video Module (2) NMEA Modules

These modules are used to capture ship information and output this acquired data through an Ethernet port, transmitting it to the DPU for processing and storage.

VDR-100G2/G2S Operation Manual

Figure 1.4 - Data Acquisition Unit

1.1.3

Audio Module

The Audio Module receives audio information from bridge microphones and vessel radios in accordance with the IEC 61996 standard. All audio data is routed to the DMM for processing, storage, and eventual retrieval. This module also controls the test buzzers used to verify the functionality of all microphones connected to the VDR-100G2. The standard Audio Module is an autonomous audio capture and broadcast device with eight (8) input ports for capturing audio data from a combination of microphones or line level inputs. An example combination may be:

Six (6) microphones Transmitted and received signals from the primary VHF radio.

The module combines pairs of input signals, digitizes the combined audio channels, and outputs the audio data through an Ethernet port. Twelve or sixteen input Audio Module units are also available for capturing audio data from additional microphones or other sources. Additional specifications:

The audio inputs are transformer coupled and can be configured on site as either microphone or line level connections. The 8, 12, or 16 audio inputs are mixed 2:1 (either LEFT/RIGHT for microphones, or TX/RX for VHF) to produce 4, 6, or 8 single-ended digital signal streams respectively. Separate level control potentiometers are located on the PCB, and can be adjusted using a screwdriver. These levels are preset during manufacturing. The audio signals are sampled to 12-bit resolution. The resulting digitized data stream is broadcast across an Ethernet cable for storage. The Audio Module Ethernet output is connected to a dedicated Ethernet port on the DMM.

VDR-100G2/G2S Operation Manual

Figure 1.5 12-Input (6-Channel) Audio Module

There are two (2) types of microphones available with the VDR-100G2:

The indoor microphones are condenser style boundary microphones, ordinarily mounted to the ceiling in the bridge area, with a junction box mounted above the ceiling for cable connection. The outdoor (external) microphone has an externally mounted wiring junction box. Both microphone assemblies include a microphone test buzzer.

Figure 1.6 - Indoor Microphone

VDR-100G2/G2S Operation Manual

Figure 1.7 - Outdoor Microphone

1.1.4

Video Module

The Video Module is an autonomous video capture and broadcast device. It has one (1) input port for capturing images from a dedicated buffered output port of the primary radar. The module digitizes the video signals and outputs the video data through an Ethernet port. Video modules with up to four (4) inputs are also available for capturing images from additional video displays. The module provides periodic updates of RGB images. For maximum flexibility, the board holds sufficient memory to accommodate 1600 x 1200 x 24-bit colour images and refresh rates up to 85Hz. For maximum capability, the A/D samples at up to 170MHz, with a clock inversion option that allows larger images to be sampled by interleaving two (2) consecutive frames. The Data Management Module (DMM) initiates the capture of video information and specifies its configuration. This includes:

The video channel to be digitized. The sources of the vertical and horizontal syncs. The coefficients for the PLL-generated pixel clock (or selection of an external clock). The dimensions (number of samples and lines) of the captured frame.

VDR-100G2/G2S Operation Manual

Figure 1.8 - Video Module

1.1.5

NMEA Input Modules

The NMEA Input Modules provide connection to all IMO-required data items in both NMEA 0183/IEC 61162 and limited ASCII data formats. NMEA modules multiplex up to eight (8) NMEA-0183 data streams from shipboard systems onto a single RS-232/422 serial data channel, and simultaneously on an Ethernet connection (UDP). Captured data is sent to the DMM via an Ethernet connection for storage and eventual retrieval. These modules use embedded microprocessor technology with real-time buffer storage to handle simultaneous arrival of data on multiple channels without conflict. Additionally:

An efficient anti-collision algorithm preserves the integrity of the data even at high incoming data rates. Data is handled on a first-in-first-out basis, assembled, and then transmitted via the serial output port to the receiving computer or data logger.

VDR-100G2/G2S Operation Manual

Figure 1.9 NMEA Input Module

1.1.6

Operation & Alarm Unit (OAU)

The Operation & Alarm Unit (OAU) provides a visible and audible alarm in the event of a VDR-100G2 error condition. Using an output connection to a vessels central bridge alarm system, the OAU alerts an Integrated Bridge System (IBS) of any VDR-100G2 system failures or error conditions. The alarm unit is also used to initiate an IMO required download operation on the VDR-100G2. The OAU has three (3) primary functions:

Alert the ships officer on watch of any detected failure within the VDR-100G2. Allow a user to secure recorded data. This action must be taken within 24 hours of any incident to prevent the recording of the incident from being overwritten. Allow a user to connect or disconnect, as well as copy secured data, to the optional RSM.

The unit has a simple menu interface which allows a user to secure the recorded data and enable or disable the optional RSM. It is equipped with:

Audible and visual alarm indicators A 12-button keypad A 4 x 20 character LED An output for monitoring in a central alarm system

VDR-100G2/G2S Operation Manual

Figure 1.10 - Operation & Alarm Unit

1.1.7

Final Recording Medium (FRM/SFRM)

The Final Recording Medium (FRM/SFRM) is a solid-state storage unit capable of storing 12 hours of VDR-100G2 data in compliance with IMO resolution A.861(20.). Additional information:

The primary function of the FRM/SFRM is to provide a protective capsule for the IMO required data acquired by the VDR. This data will be used, in the event of an incident, by an accident investigation team. The FRM/SFRM is mounted on the exterior deck of the ship and connected to the DMM. The FRM/SFRM receives data from the VDR via an Ethernet link.

Figure 1.11 VDR-100G2 Final Recording Medium (HVR-01)

VDR-100G2/G2S Operation Manual

10

Figure 1.12 - VDR-100G2 Final Recording Medium (HVR-02)

Figure 1.13 - VDR-100G2S Final Recording Medium (SVR-01)

VDR-100G2/G2S Operation Manual

11

Figure 1.14 - VDR-100G2S Final Recording Medium (SVR-02)

1.1.7.1 Tron Float-Free Capsule The Tron Float-Free Capsule is a combined FRM and Cospas-Sarsat EPIRB (Emergency Positioning Indicating Radio Beacon), approved for use with the VDR-100G2S. The capsule contains a memory module with a standard 1.75GB storage capacity and 10Mb Ethernet with TCP/IP interface. The capsule will store 12 hours of captured data. In a situation where a ship may be sinking, the capsule will float free while transmitting both its position and MMSI for at least seven (7) days.

Figure 1.15 - Jotron "Tron" Float-Free Capsule

1.1.7.2 ACR Float-Free Capsule The ACR Float-Free capsule contains non-volatile memory (Flash), intended to store ship parameters in real time. The storage memory will continually store the last 12 hours (minimum) of received data. The interface between the VDR-100G2S and the memory capsule is a standard 10/100 Base-T Ethernet connection using TCP/IP standard protocol. Power for the capsule is provided over the same Ethernet cable using PoE (Power Over Ethernet). This feature has the advantage in that a separate power cable is not required. Much like a black box on an airplane, in an emergency your float free 406 memory capsule will store the last 12 hours of the ships critical and navigational data to be retrieved and reviewed to assist in explaining the cause of the accident.

VDR-100G2/G2S Operation Manual

12

1.1.8

Remote Storage Module (RSM)

The Remote Storage Module (RSM) is an optional data storage device which provides the ability to automatically archive longer periods of recorded data. The module:

Has an Ethernet interface to accept data from the VDR and a USB2.0 port which allows the stored data to be retrieved and/or reviewed on any modern PC. Sufficient to archive 160GB of data, or can be used to retrieve several previously secured data sets.

When the RSM is supplied as a data retrieval device, a universal AC adapter is included. When supplied with the extended archiving software module, universal AC and 24VDC power supplies are included. The RSM is similar to the FRM, except:

It is not designed to survive extreme conditions. It has a much larger storage capacity. It is small and easy to transport.

Figure 1.16 - Remote Storage Module

1.1.9

External Data Interfaces

The External Data Interfaces, used to sense data signals from ships equipment in order to provide 61162/NMEA0183 compliant data sentences, are recorded via the NMEA Modules described earlier in this documentation. Non-compliant data can be recorded using one (1) of the following interfaces: DataAnalog The DataAnalog Input Module monitors the status of eight (8) analog input signals and indicates the voltage or current which corresponds to the equipment setting on each input channel via an NMEA0183/IEC 61162 format data sentence transmitted once per second. The DataAnalog interface has eight (8) channels and can simultaneously monitor signals from four (4) separate systems while maintaining isolation between them. This interface is ideally suited to measure the electrical indications for order and response from four (4) shipboard systems (i.e., Rudder Order/Response, ME RPM Order/Response, Pitch Order/Response, Bow Thruster Order and Response). DataDiscrete Discrete inputs can be monitored via Rutter Technologies DataDiscrete interface unit. Discrete inputs are data items recorded simply as open/closed or on/off. These discrete inputs reflect their status by the presence or absence of discrete voltage levels or by the closure of a set of relay contacts. The

VDR-100G2/G2S Operation Manual

13

DataDiscrete input module monitors discrete input points and outputs an NMEA-0183/IEC 61162 format data sentence to represent them. This output is connected to the VDR-100G2 through a NMEA input channel on the NMEA Module. The DataDiscrete interface is a microprocessor-based unit that incorporates 24 opto-isolated inputs arranged in four (4) banks of six (6) (with each bank having its own common return). Additional Interfaces A number of additional Rutter Technologies interfacing devices, including the DataGyro, DataProtocol, DataSplitter, and DataSynchro can be supplied to convert data from shipboard systems to an output sentence in compliance with the IEC 61162/NMEA0183 format. For further details, contact Rutter Technologies Inc. or an authorized Rutter dealer.

1.2

Client / Playback PC

An optional Client PC connected to the DMM via an Ethernet connection may be used for two (2) purposes:

Downloading data from the VDR Data playback

When the Client / Playback PC is connected to the VDR-100G2 via an Ethernet connection, previously recorded data may be downloaded at any time during normal system operation without interrupting the VDR-100G2 recording process. This downloaded data may then be replayed via the playback software. The playback software presents radar video and IEC 61162 data on the PC display and outputs the audio through the system sound card. The audio channels may be mixed on playback or played back separately, permitting localization of sound sources. During playback, all the primary navigation data required for operating an electronic chart system or an electronic chart display and information system is available via the serial port on the playback PC. Software associated with the optional Client PC is described in Section 6 - PLAYBACK SOFTWARE.

1.2.1

Minimum Requirements
Pentium III or higher processor 256 MB of memory SVGA Video port and monitor (it is recommended that the monitor be 15 or larger and supports a non-scrollable resolution of 1024x768 or greater) Audio hardware with PC speakers or headphones 100 Base-TX Ethernet Interface USB 2.0 Port Serial data port (if external ECDIS display support is required) 16X DVD-R/DVD-RW drive 80 GB or larger internal Hard Disk Drive USB, AT or PS/2 mouse and keyboard Power Supply: Dual Input Voltage: 115V at 60 Hz; or 220V at 50 Hz English O/S Edition: Windows 2000 or Windows XP (recommended).

VDR-100G2/G2S Operation Manual

14

1.3

System Overview Drawings

Figure 1.17 - System Overview (with DAU)

VDR-100G2/G2S Operation Manual

15

Remote Storage Module

VDR-100G2

VDR-100G2/G2S Operation Manual

STATUS CLEAR
> ENTER FOR MAIN MENU
Emrg. Backup Enter Mute P rev. Next V iew Data Cancel Text RSM Dim

Figure 1.18 - System Overview (without DAU)

16

TECHNICAL SPECIFICATIONS

The following tables contain a summary of the technical specifications for the Rutter VDR-100G2 system components:
Power Consumption 1.1 A @ 220VAC (approx. 250 Watts) 2.1 A @ 120VAC (approx. 250 Watts) 11 A @ 24VDC 2.9 A @ 220VAC (during battery charge) 5.3 A @ 120VAC (during battery charge) 26.7 A @ 24VDC (during battery charge) 10 A @ 220VAC 15 A @ 120VAC 30 A @ 24VDC

Normal Operating Current (approx)

Maximum Current Draw (approx)

Recommended Ship Main Breaker

DPU Specifications Weight Dimensions Input Power Output Power 43.2Kg 350 x 400 x 400mm (H x W x D) 85 -264 VAC 50-60Hz (optional 24VDC) 24VDC to FRM, optional DAU, Alarm Module, optional Remote Storage and optional interfaces

Data Ports

Ethernet input from Audio, Video, and NMEA Modules Ethernet Output to FRM Ethernet Output to Optional Remote Storage and/or Download/Playback PC RS232 Input/Output for Alarm Module RS232 Input/Output for Power Control Module

Battery Backup Power

2 Hrs @ -15 Deg C for Audio system, Alarm Module, DMM, and FRM

Data Storage Capacity

24 hours of most current data (Units prior to S/N: 20105020037, with the exception of S/N: 20105020034, have a standard storage capacity of 12 hours of current data) Plus multiple secured data sets and 30 days extended NMEA

VDR-100G2/G2S Operation Manual

17

DAU Specifications (the DAU Cabinet is optional and not applicable to VDR-100G2S) Weight Dimensions Input Power Output Power Audio Input Capacity 16.8Kg 400 x 600 x 150mm (H x W x D) 24VDC from DPU 24VDC to remote interfaces (Max 6A) 8, 12, or 16 Audio inputs Flexible Microphone and VHF/Line level combinations

Video Input Capacity Up to 4 video input ports 170MHz pixel rate with 2 megapixels input resolution, up to 340MHz pixel rate captured from two consecutive frames with clock inversion (Includes 1600 x 1200 x 75 Hz & 1280 x 1024 x 85 Hz) 24 bit RGB; monochrome H and V sync input

Data Input Capacity 8 or 16 NMEA 0183/IEC61162 Data Input ports. Interfaces for converting non-standard signal formats are to be DIN rail mounted as close to the signal source as practical. The following interfaces are available for remote mounting: DataAnalog analog signals interface DataDiscrete contact signal interface DataGyro gyrocompass interface DataSynchro synchro type gyrocompass interface DataSplitter NMEA splitter interface DataProtocol protocol conversion interface

FRM/SFRM Specifications Weight HVR-02: 10.9kg; SVR-02: 10.4kg; Tron Float-Free: 3.5kg; ACR Float-Free (EPIRB Only): 1.021kg

Dimensions

HVR-02: Height: 218.3mm, Diameter: 206.5mm, Base Width: 182.39mm SVR-02: Height: 215.17mm, Diameter: 206.5mm, Base Width: 182.39mm Tron Float-Free: Height: 695mm, Depth: 226mm, Width: 205mm ACR Float-Free (EPIRB Only): Height: 178mm, Depth: 108mm, Width: 92mm

Input Power

24VDC

VDR-100G2/G2S Operation Manual

18

Memory Type Capacity

HVR-02/SVR-02: Solid State; Float-Free: Flash Disc 12-hour minimum ( 1.75GB )

OAU Specifications Weight 1.4Kg With front mounting plate: 144 x 144 x 52.3mm Without front mounting plate: 136.6 x 136.6 x 50mm 24VDC 60dBA

Dimensions

Input Power Audible Alarm

Indoor Microphone Assembly Specifications Weight Dimensions Input Power 0.95Kg Mic: 64 x 92 x 31mm / Box: 80 x 149.1 x 56.5mm Phantom Power

Optional Outdoor Microphone Specifications Weight Dimensions Input Power 1.17Kg Mic: 64 x 92 x 31mm / Box: 85.1 x 129.9 x 65.7mm Phantom Power

Optional RSM Specifications Weight Dimensions Input Power Capacity 1.36Kg 35 x 127 x 214mm 24VDC or Universal AC with external power supply 160GB

Optional RSM 24VDC Power Supply Specifications Weight Dimensions Input Power 1.0Kg 138 x 166.2 x 50mm 24VDC

VDR-100G2/G2S Operation Manual

19

This page is intentionally blank.

VDR-100G2/G2S Operation Manual

20

USER GUIDE

The following section provides a user guide for operating the VDR-100G2/S. All user-level operation occurs via the OAU. The OAU provides the ability to secure data as well as offering audible alarms that alert the user to potential problems with the unit and/or component connections.

Figure 3.1 OAU Menu Pad

3.1

Securing Data

To secure data to the DMM, complete the following steps: 1. Press the Emrg Backup button on the OAU menu pad. The following message will appear on the OAUs LCD: Perform Emergency Backup of VDR Data > Enter to Confirm 2. Press the Enter button on the OAU menu pad. The following message will appear: Downloading Data Please Wait 3. Allow the download to complete. A progression message may appear (i.e., 20% Complete) dependant upon the size of the download.

3.2

Viewing Secured Data

To view previously secured data sets, complete the following steps: 1. Press the View Data button on the OAU menu pad. 2. Secured data sets appear two (2) per screen. If more than two (2) secured data sets exist, press the Prev and/or Next buttons on the menu pad to scroll through all sets available. Data sets

VDR-100G2/G2S Operation Manual

21

appear from oldest to newest and are recorded with the following time format: yyyy-mm-dd-hr-mt (where yyyy=year, mm=month, dd=day, hr=hour, and mt=minute).

3.3

Securing Data to the RSM

For instructions on securing data to the RSM/USB Memory Stick, see Section 5 RSM & USB Memory Stick.

3.4

Muting Audible Alarm

To mute the audible alarm, press the Mute key on the OAU menu pad.

3.5

Dimming the Display

To dim or brighten the LCD display, press the Dim key on the OAU menu pad. There are four (4) LCD brightness levels ranging from off to bright.

3.6

Test Screen

To obtain the VDR Record software version number or the unique DMM Hardware ID, press the Test key on the OAU menu pad. An example of the information provided via the Tests menu, is as follows:

**Test Screen** Version: 4.0X.00 ID: 55N5SS5S55X21 Press the Cancel button to return to the main screen.

3.7

Alarm Code Description

Listed below are the alarm codes that may appear on the OAU LCD display: Alarm Code System Error Video Error Audio Error FRM Error Power Fail Description Communication with the Record Application has been lost Communication with the Video Module has been lost Communication with the Audio Module has been lost Communication with the Final Recording Medium has been lost Loss of utility power

VDR-100G2/G2S Operation Manual

22

PCM Error Remote Error Serial Error Mic Error Disk Error GPS Error

Communication has been lost with the Power Control Module Communication has been lost with the Remote Storage Module Communication has been lost with the NMEA Module Communication has been lost with one of the microphones Failure to secure a data set Failure to record GPS data
Table 3.1 Alarm Code Description

Pressing the Mute button acknowledges the alarm code and silences the alarm.

VDR-100G2/G2S Operation Manual

23

This page is intentionally blank.

VDR-100G2/G2S Operation Manual

24

DATA RETRIEVAL

The VDR-100G2 is supplied with several options for accessing and replaying data in order to reconstruct voyages:

The primary method of retrieving data is via the USB Memory Stick. The copying of data to the USB Memory Stick is initiated at the OAU via the RSM button (see Section 4.4 - Remote Storage Module). The Remote Storage Module (RSM). The download is initiated at the OAU (see Section 4.4 Remote Storage Module). An alternate method is to download data via a client PC connected to the VDR by a LAN connection. All necessary software is optional and resident on the client PC (see Section 4.2 - Installation of Download Software).

4.1

Optional Client Download PC

If the customer should choose to make use of the optional download client PC, additional copies of the playback software are supplied. The Download/Playback client PC should be a Pentium class or equivalent, and IEC 60945 certified if installed on the Bridge. The computer system should, as a minimum, include:

Pentium III or higher processor 256 MB of memory SVGA Video port and monitor (it is recommended that the monitor be 15 or larger and supports a non-scrollable resolution of 1024x768 or greater) Audio hardware with PC speakers or headphones 100 Base-TX Ethernet Interface USB 2.0 Port Serial data port (if external ECDIS display support is required) 16X DVD-R/DVD-RW drive 80 GB or larger internal Hard Disk Drive USB, AT or PS/2 mouse and keyboard Power Supply: Dual Input Voltage: 115V at 60 Hz; or 220V at 50 Hz English O/S Edition: Windows 2000 or Windows XP (recommended)

VDR-100G2/G2S Operation Manual

25

4.2
1. 2.

Installation of Download Software

Copy the Download application (VDR_Download.exe) from the supplied media to the desktop of the download computer, or if an install file is supplied, double-click the Install VDR Download.exe file. Configure the download computer as a Client for the Download Application to connect to the VDR-100G2 and retrieve the recorded data. To do this, the download PC must be in the same IP segment as the download port on the VDR. The VDRs download port occupies IP address 200.200.200.200. The client PC must be in the same range, with the last segment different than the VDR (as shown below.) To change the IP segment: Open the Control Panel via the Start menu. Double-click the Network Connections icon. Right-click on the Local Area Connection icon and select Properties from the pop-up menu. In the Local Area Connection Properties window, highlight Internet Protocol (TCP/IP) and click the Properties button located directly below the available options. In the subsequent Internet Protocol (TCP/IP) Properties window, select the Use the following IP address radio button and enter 200.200.200.2 (the last number can be any number from 2 to 254, except 200.) Click the OK button in the Internet Protocol (TCP/IP) Properties and the Local Area Connection Properties.

There are two (2) steps necessary to install the Download application onto the client PC:

Figure 4.1 - Establishing TCP/IP Address

VDR-100G2/G2S Operation Manual

26

4.2.1

Starting the Download Process

Start the download utility by double-clicking the download.exe icon located on the Windows desktop. See Figure 4.2 - Download Software Main Screen for an example of the download utility.

Figure 4.2 - Download Software Main Screen

4.2.2
1.

Begin the Download

Select Start download from the Download Controls menu.

Complete the following steps to begin the download of the current data set:

Figure 4.3 - Download Controls Menu

2. 3.

Enter a password when prompted. Once prompted with the Download Settings window (see Figure 4.4 - Download Settings Window), choose from the following available settings: Download complete data set. Download partial data set once this option has been chosen, Start and Stop times become available. Using the appropriate slide-bar, set the time frame that will begin and end the downloaded data set. Normal data set. Extended NMEA data set this option allows for the download of the extended NMEA data set only.

VDR-100G2/G2S Operation Manual

27

Figure 4.4 - Download Settings Window

4. 5. 6.

Confirm that the stated download destination is correct. If it is not, press the Change Destination button, select the correct destination from the file window, and press OK. Press the Start Download button. Confirm all settings are correct in the confirmation window and press OK (if they are not, press Cancel and make the appropriate changes in the Download Settings window).

Figure 4.5 - Sample Download Directory

Once a download is complete, MainAudio, MainNMEA, and MainVideo folders are visible. The vdrparams.ini and vdr-cfg.txt files are also downloaded and saved to the specified download directory. See Figure 4.5 - Sample Download Directory for an example of a typical download directory.

VDR-100G2/G2S Operation Manual

28

4.2.3

Download Secured Data Set

Complete the following steps to download one (1) of multiple secured data sets from the DMMs internal hard drive: 1. Select Download Secured Dataset from the Download Controls menu. 2. A download progress window will appear indicating that the application is receiving information from the DMM. 3. In the subsequent Download Secured Datasets window, all available secured datasets will be visible. Each dataset shows the date it was initially secured, file size, and start and end time.

Figure 4.6 - Download Secured Datasets

4. Select the appropriate dataset from the list. 5. To download a complete dataset, choose the Download complete data set radio button under Download duration. To download a partial dataset, choose Download partial data set. 6. If choosing to download a partial dataset, a window will appear from which the time range to be downloaded must be chosen. The associated scroll bar is used to select a start and/or end time (the exact time may also be entered directly in to the time fields.)

Figure 4.7 - Partial Download Window

7. To choose a directory to which the datasets will be downloaded, other than the one listed under Destination, press the Change Destination button and follow standard Windows procedure for selecting a desired directory. 8. Once the duration and destination are correct, press Start Download.

VDR-100G2/G2S Operation Manual

29

9. Enter a password and press OK. 10. A Download Settings dialog will appear providing confirmation information for the dataset to be downloaded. If all information is correct, press OK to begin the download.

Figure 4.8 - Confirm Download Settings

4.2.4

Extended NMEA Download

The Extended NMEA data set is a VDR-100G2 option, which supports the recording of up to 185 days of NMEA data to the DMM. When an extended NMEA download occurs, no video or audio data is included in the download. To select the extended NMEA download, check the Extended NMEA Download located in the Download Settings window (see Figure 4.4 - Download Settings Window).

Important! The extended NMEA data set must be purchased as an option and configured on the VDR-100G2 during installation. If the VDR-100G2 is not configured for the extended NMEA data set, this option will not function in the download software.

4.2.5

Complete vs. Partial Download

A complete download is the process of downloading a full 24-hour data set from the DMM. As a user may want only a partial download, a Download partial data set option is available. Select either Download complete data set or Download partial data set in the Download Settings window (see Figure 4.4 - Download Settings Window) to download the desired data set.

Figure 4.9 - Completed Download

VDR-100G2/G2S Operation Manual

30

4.2.6

Error Log and Battery Log

To download the error log or battery log file, select the applicable item (Download Error Log or Download Battery Log) from the Download Controls menu (see Figure 4.3 - Download Controls Menu). The system will prompt the user to select a location to save the log file.

4.2.7

Disconnecting from the VDR

To disconnect, simply choose Exit from the File menu.

4.3

USB Memory Stick

The USB Memory Stick is the primary means of retrieving a secure data set recorded by the VDR. The method for initiating a download to the USB Memory Stick is the same as the method for initiating a data download to the RSM. See Section 5 - RSM & USB Memory Stick for further information.

4.4

Remote Storage Module

If installed, the Removable Storage Module (RSM) provides a means of copying data recorded by the VDR. See Section 5 - RSM & USB Memory Stick for information on downloading to the RSM.

VDR-100G2/G2S Operation Manual

31

This page is intentionally blank.

VDR-100G2/G2S Operation Manual

32

RSM & USB Memory Stick

The primary means of removing data recorded by the VDR-100G2 is via the USB Memory Stick (version 4.05.00 of the vdr_record.exe application and later). Each VDR from Serial No. 20107020850 forward includes a USB Memory Stick. For units built prior to this time, the primary means of removing data is via the RSM. Refer to Table 5.1 - Data Download: USB Memory Stick vs. RSM below for a comparison of versions for copying data. There are no changes in OAU functionality between these units and versions:

Where a unit is fitted with a USB Memory Stick and version 4.05.00 of the software, data copied using the RSM menu will be copied to the USB Memory Stick. Where a unit has no USB Memory Stick, data is copied to the RSM (if fitted). A VDR with a USB Memory Stick may also have an optional Remote Storage Module (RSM) for the purposes of automatic archiving.

Unlike the FRM, which contains only data required by IMO regulations, the USB Memory Stick and/or RSM, dependant upon customer requirements, may contain a much larger and highly detailed data set. For units without a USB drive, read this section to understand that the RSM will perform the same data copying functionality without need for software or hardware changes. Comparison of VDR-100G2 Units with USB Memory Stick vs. RSM
VDR Fitted with USB Memory Stick Only RSM Only Both RSM & USB Memory Stick Data Copy Destination (when using OAU) USB Memory Stick RSM USB Memory Stick Table 5.1 - Data Download: USB Memory Stick vs. RSM Auto Archive RSM RSM RSM

Important! The configuration (Vdr-cfg.txt) and parameters (vdrparams.ini) files, which may be used to correctly interpret playback information, are stored and located in the root directory of the removable drive.

A portable copy of the recorded data can be obtained by copying data from the DMM internal hard drive to the USB Memory Stick or RSM. Copying data to the USB Memory Stick (or RSM) does not affect the normal recording operation of the VDR-100G2. The OAU is used to initiate copying of data to the USB Memory Stick (or RSM) for removal and analysis purposes. To playback the data from the RSM/USB Memory Stick, a PC will require the following:

VDR-100G2/G2S Operation Manual

33



The minimum requirements for a PC outlined in Section 4.1 - Optional Client Download PC. Rutter Technologies playback software.

Important! Downloading a secure data set to the USB Memory Stick is done using the same procedure as downloading to the RSM (described below). If a system has both an RSM and USB Memory Stick connected at the same time, the download instructions below will only download data to the USB Memory Stick. The RSM will continue in auto-archiving mode only.

5.1

Copying Data to RSM/USB Memory Stick

To retrieve data using the OAU, it is necessary to ensure the USB Memory Stick/RSM is connected and recognized by the G2 system. Complete the following steps: 1. If not already connected, insert the USB Memory Stick into the available USB port or attach the Ethernet and power cable from the RSM to the DPU (or connect the USB Memory Stick to the DMM). Press the RSM button on the OAU menu pad. At the main menu screen of the OAU, two (2) options are displayed:

2. 3.

Copy Data RSM Archiving

Note! The RSM cannot be simultaneously connected via Ethernet to the VDR while connected to the Client PC via a USB connection. 4. Ensure the Copy Data option is highlighted (blinking cursor is adjacent to the option.) Once highlighted, press the Enter button on the OAU menu pad. 5. Three (3) options are now displayed:

Copy Current Data: allows a user to retrieve a full 24-hour data set. See Section 5.1.1 Copy Current Data. Copy Secured Data: allows a user to retrieve specific segments that have been previously secured and may range in length of time. See Section 5.1.2 - Copying Secured Data. Copy Extended NMEA: allows a user to retrieve extended NMEA data. See Section 5.1.3 - Copying Extended NMEA Data.

VDR-100G2/G2S Operation Manual

34

Important! If Auto Archiving is enabled, do not physically disconnect the Remote Storage Module before disconnecting it from the system via the OAU. See Section 5.1.4 Disconnecting the RSM for instructions on disconnecting via the OAU. It is also recommended to power off the unit prior to physically disconnecting it. Once the RSM is physically disconnected from the DMM, it will take approximately one (1) minute for the system to recognize this disconnect. DO NOT reconnect the RSM before this one (1) minute wait period has elapsed, as it will not be recognized by the system. If the RSM is accidentally reconnected before the one (1) minute wait period has elapsed, physically disconnect the RSM from the DMM and wait one (1) minute before physically reconnecting. Once the RSM is physically connected, connect to the DMM software via the OAU.

5.1.1

Copy Current Data

To copy the current data from the internal drive of the DMM to the USB Memory Stick/RSM, the following steps must be completed:

Press the RSM key on the OAU menu pad Highlight Copy Data and press Enter on the OAU menu pad Highlight Copy Current Data and press Enter on the OAU menu pad

The full data set residing on the internal drive of the DMM will be copied to the USB Memory Stick/RSM. As the data is copied, the OAU display may indicate the percentage of data that has been copied dependant upon the size of the download. To cancel the download, simply press Cancel on the OAU menu pad.

5.1.2

Copying Secured Data

Data sets can be secured on the internal drive of the DMM at any time via the OAU menu pad. If sufficient space does not exist on the internal drive to secure a data set, the oldest secure data set will be automatically deleted. Therefore, it is convenient to copy any one of these secure data sets to the USB Memory Stick/RSM. Secured data sets can be copied to the USB Memory Stick/RSM for longer term storage or for portability to shore side facilities. To copy a secured data set to the USB Memory Stick/RSM, the following steps must be completed:

Press the RSM key on the OAU menu pad. Highlight Copy Data and press Enter on the OAU menu pad. Highlight Copy Secured Data and press Enter on the OAU menu pad. All available secured data sets (displayed in yyyy-mm-dd-hr-mt format) will become visible. Secured data sets appear two (2) per screen. If more than two (2) secured data sets exist, press the Prev and/or Next buttons on the menu pad to scroll through all sets available. The total number of data set screens available is shown on the screen (for example, Page 3/21). Once the desired data set is highlighted, press the Enter key on the OAU keypad. Press the Enter key again to confirm the download.

VDR-100G2/G2S Operation Manual

35

The selected secured data set will be copied to the USB Memory Stick/RSM. As the data is copied, the OAU display will indicate the percentage of data that has been copied. To cancel the download, simply press Cancel on the OAU menu pad.

5.1.3

Copying Extended NMEA Data

The VDR100G2 can optionally store up to 185 days of NMEA data. This data can then be copied to the USB Memory Stick/RSM by the following steps: 1. Press the RSM key on the OAU menu pad. 2. Highlight Copy Data and press Enter on the OAU menu pad. 3. Highlight Copy Extended NMEA Data and press Enter on the OAU menu pad. All Extended NMEA data will then be copied to the USB Memory Stick/RSM. As the data is copied, the OAU display will indicate the percentage of data that has been copied. To cancel the download, simply press Cancel on the OAU menu pad.

5.1.4

Disconnecting the RSM

When Auto Archiving is enabled, it is important to disconnect via the OAU keypad prior to physically disconnecting from the VDR. To check if Auto Archiving is enabled, press the RSM key on the OAU keypad; if RSM Archiving appears as a menu option, it is enabled. To disconnect the RSM: 1. Press the RSM key on the OAU menu pad. 2. Press the down () arrow to select the RSM Archiving option on the OAU LCD display and press the Enter key. 3. Select Disable Extended Archiving and press the Enter key on the OAU menu pad. 4. Power off the RSM (switch RSM Power Switch to Off position). 5. Remove all cable connections from the RSM.
USB Port Power Input

Power Switch

Ethernet Port

Figure 5.1 - Rear View of RSM Unit

Important! Do not disconnect the USB Memory Stick during data transfer. If data is being transferred to the Memory Stick the blue light located on the body of the Memory Stick will flash rapidly. Once data transfer is complete the blue light will stay solid.

VDR-100G2/G2S Operation Manual

36

5.2

Connecting Client PC to RSM

To retrieve data from the RSM using the Client PC, complete the following steps: 1. Physically disconnect the RSM Ethernet cable and connect it to the Client PC using an A to B mini USB cable. 2. The RSM will be visible on the Client PC as a connected hard drive.

VDR-100G2/G2S Operation Manual

37

This page is intentionally blank.

VDR-100G2/G2S Operation Manual

38

PLAYBACK SOFTWARE

The playback module accompanies the base model VDR and is resident on the download client PC. Additional playback software is available for use in shore-side offices. This additional software is necessary for the playback of data on the RSM or other media once it has been removed from the ship and transported to the office environment.

Important! The computer on which the Playback application is being installed must have its regional and language options adjusted to English. This may be done by double clicking the Regional Options icon in the Control Panel window and selecting English from the language drop down list. It is recommended that either English (United States) or English (Canada) is selected. However, any of the available English options are acceptable.

6.1

Playback Installation - Client PC

The installation of playback software is automated and requires little interaction. The install is performed via a self-extracting executable file and is automatically installed to the C:\Program Files\Playback directory, with a shortcut placed on the Windows desktop. The install file will normally be named Install VDR Playback.exe. To begin the installation, complete the steps listed below: 1. On the installation CD, double click the file entitled Install VDR Playback.exe.

Figure 6.1 - Installation Executable File

2.

Choose the directory to which the executable will be installed.

Figure 6.2 - Choose Installation Directory

3.

To abort the installation, click the Abort button on the Installing message window.

VDR-100G2/G2S Operation Manual

39

Figure 6.3 - Installing Message Window

4. The install process will place a shortcut to the playback software on the desktop.

6.2

Starting the Playback Application

To start the playback application, double click the playback icon located on the desktop (as mentioned in step 4 of the installation process above). The application will look similar to Figure 6.4 - Playback Software shown below. Note that the playback application interprets information provided in the ships VDRPlayback.ini file therefore the playback interface may contain elements and controls different from what is shown below.

Figure 6.4 - Playback Software

6.2.1

Configuration File

The vessel displayed in the Playback application is automatically configured via the ships configuration file, which is created by the installation technician during the installation of the VDR. The configuration file pertaining to the ship whose data will be used by the Playback application must be located in an easily accessed location on the local hard drive of the playback PC.

VDR-100G2/G2S Operation Manual

40

Upon start-up of the Playback application, the configuration file can be loaded using the File > Configure menu item.

Figure 6.5 - Configuration File Selection - Menu Item

A dialog window will appear allowing the user to select the applicable file. Once the file has been selected the Playback application will shut down momentarily and restart automatically. Upon restart the chosen configuration file will load automatically. To change the configuration file, select the File > Configure menu item, as above, and choose the newly desired file.

Figure 6.6 - Restart Warning

With the VDR-100G2, the ships configuration file will accompany every available data set. When a data set is selected the configuration file will be automatically reloaded as necessary.

6.3
1. 2. 3.

Choosing Data for Playback

Choose the Open icon located directly underneath the File menu A dialog box will appear. Use the dialog box to locate a folder containing downloaded data and select one of the three (3) .vdr files. Ensure All Files is selected in the Files of Type drop down box. The .vdr files accompany every download and act as an index to the actual data files. They are named according to the data items they reference: AudioDir.vdr for audio, NMEADir.vdr for NMEA data and VideoDir.vdr for video data. Selecting any one of these three files will open a data set for playback.

To select a data set for playback:

Note! If the download directory does not display three (3) files with extensions of .vdr, it is possible that the Microsoft operating system is treating them as hidden files.

VDR-100G2/G2S Operation Manual

41

To ensure that the .vdr files are being displayed (and not hidden by the operating system), follow these steps: 1. 2. 3. 4. 5. Open Windows Explorer Select Folder Options from the Tools menu Select the View tab Ensure that Show Hidden Files and Folders is selected Press the OK button.

Figure 6.7 - Choose a .vdr File

6.3.1

Unarchive Extracted Data

Data for playback can also be chosen from a previously extracted data archive. If a portion of data has been previously extracted and archived it can be opened for playback via the File > Unarchive Extracted Data file menu option.

Figure 6.8 - Unarchive Extracted Data

To playback the archived data after selecting the Unarchive Extracted Data file menu option, a user will have to locate the .rfa (archive) file and select a folder to which the data can be extracted. Once extracted, an applicable configuration file will need to be selected in order to continue playback.

VDR-100G2/G2S Operation Manual

42

6.4

Enabling Ethernet Broadcasts

To enable the Playback software and Client PC to broadcast data across a network for use with a separate Electronic Charting System (ECS) or software, open the Output menu dropdown and select Enable Ethernet Broadcast. If a check appears adjacent to this option, broadcasting is currently enabled. To disable this option, ensure no check sign appears adjacent to it.

Figure 6.9 - Enabling Ethernet Broadcasting

The broadcast will occur on UDP Port 4450 and 4451. Refer to the relevant ECS manual to properly enable a PC to receive an Ethernet broadcast from Rutter Technologies Playback software.

6.5

Starting the Playback

To start the data playback, complete the following steps: 1. After a set of download data has been selected for playback, choose Start from the Playback menu or press the Play button located on the Controls toolbar
Play Pause Fast Forward Fast Forward Rate Playback Data Rewind Time

Stop

Open Figure 6.10 - Controls Toolbar

2. A dialog box will appear asking for a password. The default password is VDR. The password is case sensitive. It must be typed in the text box and the OK button clicked 3. After entering the correct password and clicking the OK button, a second dialog box will appear, asking for a start time. Use the scroll bar (or enter a time in the text boxes) to select a playback start time. Click OK to begin the playback.

Start Time Scrollbar

Figure 6.11 - Choose Start Time For Playback

VDR-100G2/G2S Operation Manual

43

6.6

Passwords

There are two (2) passwords required to run the playback software. The first is necessary to run the playback. It is supplied with the software and can be changed by choosing Set Password from the Playback file menu. A dialog box will appear asking for the old and new passwords. The second password is for playback of audio data. It can be changed by choosing Set Password from the Audio file menu. All default passwords are VDR (case sensitive).

Figure 6.12 - Change Password

6.7

Playback Controls

The playback can be controlled via Playback menu items or by using the buttons located on the Controls toolbar. Both options offer a full range of controls, including the ability to run the playback in fast time (with the additional option of choosing replay speed). Figure 6.10 - Controls Toolbar provides an illustration of the toolbar. If available for use, buttons will appear blue (such as the Play button in the illustration). If unavailable for use, buttons will be greyed (such as the Pause button in the illustration). While playback is stopped, the Fast Forward Rate drop down box can be used to set the playback fast forward speed.

Note! The Fast Forward Rate drop down box cannot be manipulated once a playback has started.

To activate the fast forward feature, press the Fast Forward button. Return the playback to normal time by pressing the fast forward button a second time. Select Set Playback Rate (Playback > Set Playback Rate) to adjust the speed of the replay using the Playback menu. A dialog box will appear requiring a time compression rate. Enter any integer from 2 to 24 (inclusive) in the open text box and press OK (see Figure 6.13 - Set Fast Forward Rate).

VDR-100G2/G2S Operation Manual

44

Figure 6.13 - Set Fast Forward Rate

The playback can be halted with the same time index in place by pressing the pause button. Press the pause button a second time to continue the playback. The Controls toolbar can also be hidden by deselecting Controls from the View menu. By default it is visible therefore a check will appear adjacent to this option. Deselecting it will remove this check mark.

6.8

Audio Volume & Channel Selection

Audio data includes continuous bridge audio and radio communications. The configuration of audio will differ between ships but is generally arranged in two (2) to four (4) banks. Individual channels contain audio data corresponding to an area of the bridge, bridge wings, or radio communications. Each channel may be included in the playback individually or in conjunction with other channels. For example, a user may wish to play back audio data recorded in the centre of the bridge while turning off external microphones where wind noise may be present.

Figure 6.14 - Audio Interface

To activate the audio portion of a playback, choose Unlock Audio from the Audio file menu (see Figure 6.15 Audio Menu). A prompt will appear requiring a password; the default password supplied with the VDR-100G2 is VDR. Press OK to activate the audio data and make each channel in the Audio file menu selectable. Once unlocked, audio data will be available for the remainder of the time playback is open. Audio can be adjusted by opening the Audio Volume window (see Figure 6.14 - Audio Interface) via the Audio Volume option in the Audio file menu.

VDR-100G2/G2S Operation Manual

45

Figure 6.15 Audio Menu

There are two (2) ways to activate an available audio channel individually:

Select the appropriate audio channel from the Audio file menu, or, Click the Active checkbox below the appropriate channel once the audio has been unlocked. It is also possible to print the audio status to the Log Tab Screen by selecting Status from the Audio file menu.

To silence a playback, simply uncheck each channel either on the Audio menu or via the Active checkbox.

6.9

Conning Tab Screen

The Conning Data Tab is the default screen upon Playback start-up. In addition to the Propulsion and Video Channel(s) (for example, PORT X-Band, STBD S-Band, and CCTV) information tab(s) found in the centre of the screen, the Conning Data Tab also contains the following information (all along the upper left hand side of the tab screen):

Date Date of playback information Time Time of playback information Latitude Ships latitude Longitude Ships longitude GPS Mode Global Positioning System: SPS, DGPS (Differential GPS), PPS, RTK (Real Time Kinematic), FRTK (Float Real Time Kinematic), and DRM (Dead Reckoning Mode) Heading Ships heading Autopilot Indicates the presence or non-presence of a heading control system (On/Off) COG Ships Course Over Ground SOG Ships Speed Over Ground Depth Depth of ship ROT Ships Rate Of Turn

6.9.1

Depth Graph

The Depth Graph provides an illustration, in metres (m), of the ships depth.

VDR-100G2/G2S Operation Manual

46

Figure 6.16 - Depth Graph

6.9.2

Wind Information

The Wind Information pane contains data regarding the winds True and Relative Direction (Dir) and Speed (Sp). A compass is also provided in order to illustrate wind direction based on ships heading. The red arrow indicates True wind direction while the green arrow indicates Relative wind direction. The ship graphic indicates the ships heading.
Red Arrow True Wind Direction

Green Arrow Relative Wind Direction

Ship Graphic Ship Heading

Figure 6.17 - Wind Information

6.9.2.1 Propulsion Data Tab The Propulsion Data Tab is custom designed for each individual ship according to propulsion systems, bow thruster configuration and NMEA strings broadcast by bridge electronics. These displays are dependant upon the VDRPlayback.ini file created for a particular ship.

VDR-100G2/G2S Operation Manual

47

Figure 6.18 Sample Propulsion Tab

6.9.2.2 Video Channel Data Tab Radar data is captured at 15-second intervals. If multiple radar images are available for video capture, capture times will be staggered but still allow for individual captures at 15-second intervals. There are a number of options available when viewing the radar data: To display the radar data in its own window, choose Full Size Video > Video Channels from the View file menu. To close this window, click the x in the top right corner. To move the radar image (once in its own window) in order to make a particular section visible without adjusting the window dimensions, click and drag by placing the mouse pointer over a section of the image, pressing the left mouse button and moving the mouse; To save the radar image as a .bmp file, select the File menu > Save > Video Channels. A dialogue will open allowing a save location to be chosen.

Figure 6.19 MultiPilot Tab

VDR-100G2/G2S Operation Manual

48

The images are captured directly from the radar display; therefore any radar supporting ECDIS or chart displays will have the ECDIS or chart image recorded.

Note! If proprietary data is present in the data playback, a Proprietary conning tab may appear. This tab window will present the available proprietary data in sentence format.

6.10 AIS Playback Tab Screen

The AIS Playback Tab Screen displays information captured from the ships AIS.

Figure 6.20 - AIS Playback Tab

There are a number of features available within the AIS Playback tab screen that allow a user to better interpret the downloaded information.

6.10.1 Targets
The Targets section of the AIS Playback tab screen provides a range of information about all targets visible in the playback window.

Targets Tab provides a list of all ships available within the AIS view screen. If a ships information becomes unavailable it remains in the list but a line is drawn through its name (it is also added to the Lost tab list (see below)). Activated Tab provides the name of the ship selected by the user in the AIS view screen. Lost Tab provides a list of ships for which information is no longer available. Dangerous Tab provides a list of all ships that are currently on a dangerous course relative to the users ship.

VDR-100G2/G2S Operation Manual

49

Figure 6.21 - Targets Information Section

Specific ship information is also available in the following tabs (located below the above mentioned tabs):

Collision Info provides information specific to a selected ships navigational course. Target Info provides registered information (e.g., MMSI, IMO, etc.) specific to a selected ship. Own Ship provides registered and navigational information for the users ship regardless of what target is selected.

6.10.2 View Settings

The View Settings section allows a user a high level of control over the AIS playback view screen.

Figure 6.22 - View Settings Section

Viewing Range It is possible to increase or decrease the viewing range of the AIS playback view screen by pressing the + and - buttons located in the upper right of the View Settings section. Note that if using a wheel mouse the viewing range can also be increased/decreased by moving the wheel while the pointer is located in the view screen. The viewing range is listed in nautical miles. Location The latitude and longitude of the selected target is listed. Center on Selected Target If this checkbox is selected the view screen will center on the selected target. Set Center Button To set the center point of the view screen, press the Set Center button, position the mouse pointer on a location on the view screen and left-click. This point will now be the center point of the view screen. Turning on the Center on Selected Target checkbox overrides this control. New View Opens a dedicated AIS Playback window.

VDR-100G2/G2S Operation Manual

50

6.10.2.1 Settings The Settings button located in the View Settings section opens an AIS Display Settings window. The settings in this window allow the user to adjust the AIS Playback display.

Figure 6.23 - AIS Display Settings Window

CPA (Closest Point of Approach) TCPA (Time to Closest Point of Approach) COG (Course Over Ground) LOA (Length Over All)

6.10.3 GuardZone
The GuardZone section allows a user to create a guard zone in the view screen. To create a guard zone press the Create button, place the mouse cursor in the view screen area and left-click in the locations required to create a guard zone shape. Double-click to complete the guard zone formation. The guard zone can be enabled or disabled by checking or unchecking the Enabled checkbox.

6.11 Fire Doors Tab Screen

The Fire Doors Tab Screen displays information regarding the status of the ships fire doors. The colour of the light adjacent to the door name, dependant upon the configuration, indicates an active (often indicated with the colour red) or non-active (often indicated with the colour green) door or opening. Should the number of fire doors exceed the initial screen space, a scroll bar will become visible allowing a user to view all available.

VDR-100G2/G2S Operation Manual

51

Figure 6.24 - Fire Doors Tab

6.12 Water Doors Tab Screen

The Water Doors Tab Screen displays information regarding the status of the ships water doors. The colour of the light adjacent to the door name, dependant upon the configuration, indicates an active (often indicated with the colour red) or non-active (often indicated with the colour green) door or opening. Should the number of water doors exceed the initial screen space, a scroll bar will become visible allowing a user to view all available.

Figure 6.25 - Water Doors Tab

VDR-100G2/G2S Operation Manual

52

6.13 Hull Openings Tab Screen

The Hull Openings Tab Screen displays information regarding the status of the ships hull openings. The colour of the light adjacent to the door name, dependant upon the configuration, indicates an active (often indicated with the colour red) or non-active (often indicated with the colour green) door or opening. Should the number of hull openings exceed the initial screen space, a scroll bar will become visible allowing a user to view all available.

Figure 6.26 - Hull Openings Tab

6.14 Log Tab Screen

The Log Tab Screen displays the size of each type of data block and the time it was recorded. When viewed in compressed time (fast forward), the size of data blocks written at each time-period is displayed, but the actual NMEA strings are not. When played back in normal time, the Log Tab Screen will also display the NMEA strings. Log information can be controlled via the Controls toolbar. To scroll illustrated information, press the Pause button on the Controls toolbar and use the Log scrollbar to navigate.

Figure 6.27 - Log Window

VDR-100G2/G2S Operation Manual

53

6.15 Alarms Tab Screen

An alarm is an on event, only displaying when triggered. When an alarm occurs, the word ALARM will display in the lower left corner of the Playback interface. The Alarms tab allows a user to view information pertaining to all triggered alarms.

6.16 Data Extraction

The volume of data contained in downloaded VDR data sets can be very large. In many instances it may be desirable to access smaller portions of the data without downloading the entire data set. As a result it is possible to copy only a specific portion of a data set, which can then be easily removed to a separate location for analysis or e-mailed to a third party.

6.16.1 Open Extraction Window

To extract a specific portion of data, begin the playback of captured data. Once data is in active playback mode allow it to play until the beginning point of the portion desired for extraction is reached: 1. Select Data Extraction option from the Data file menu.

Figure 6.28 - Data Extraction Option

2. The Data Extraction window will open (see Figure 6.29 - Data Extraction Window below). This may take a number of seconds. The start time will automatically appear as the point in the playback where the Data Extraction window was opened.

Figure 6.29 - Data Extraction Window

VDR-100G2/G2S Operation Manual

54

6.16.2 Selecting Data for Extraction

With the Data Extraction window open it is now necessary to select a segment of data to extract and an extraction destination. 1. Three (3) data stream options (Video, Audio, and NMEA) are available for download. Check the adjacent checkbox to select the desired data stream. If no data stream is selected the Start and Stop scroll bars will not be available. 2. When the Video checkbox is selected additional options will appear (may take a number of seconds). The user will have the option to download individual Video channels as required (if available). There is also an option to select one (1) to four (4) video image(s) per minute; selecting 1 allows a user to reduce the size of the Video data extraction (one (1) image capture per minute).

Figure 6.30 - Data Stream Options w/ Video Selected

3. Select a destination directory by clicking the word Destination (or, alternately, choosing Choose Destination Dir from the Data file menu). Note that the destination directory cannot be the same as the source directory and cannot contain any other files. 4. Select a Start and Stop time for the extracted segment. As mentioned above, the Start time automatically appears as the time when the Data Extraction window was opened. However, this can be changed. To adjust either the Start or Stop time, move the applicable scroll bar. The file size of the extracted segment will appear to the right of the Stop scroll bar. This is particularly useful, for example, when attempting to extract a segment to copy to a recordable Compact Disc. 5. To create an archived file of the extracted data at the same time as the extracted data is being copied to the selected destination folder, select the Archive Extracted Data checkbox. 6. To start the data extraction, press the Start button located in the lower right of the Data Extraction window or choose the Extract option in the Data file menu (Data > Extract). 7. A progress bar will appear at the bottom of the window to indicate the progress of the extraction. 8. Once completed, the Data Extraction window can be closed via the Exit option in the File menu (File > Exit).

6.17 Closing the Application

The application cannot be closed while a voyage playback is running. To close: 1. 2. Stop the playback by selecting Stop from the Playback menu, or by pressing the Stop button in the Controls toolbar. Press the Close (x) button in the upper right hand corner of the applications main window, or choose Exit from the File menu.

VDR-100G2/G2S Operation Manual

55

Notes:

VDR-100G2/G2S Operation Manual

56