0% found this document useful (0 votes)
36 views

Working With Downloader Service Program: Super-Dl - Exe

1. The document provides instructions for using the SuperDL.exe program to download firmware to a device connected via an optical cable. 2. Key steps include extracting the download file, identifying the correct COM port, setting the device to system mode, selecting the correct .bin file, and monitoring messages and LEDs to check the download status. 3. When the procedure is finished, the device's ready LED will light up, indicating it is ready to use with the new firmware.

Uploaded by

kgskgm
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
36 views

Working With Downloader Service Program: Super-Dl - Exe

1. The document provides instructions for using the SuperDL.exe program to download firmware to a device connected via an optical cable. 2. Key steps include extracting the download file, identifying the correct COM port, setting the device to system mode, selecting the correct .bin file, and monitoring messages and LEDs to check the download status. 3. When the procedure is finished, the device's ready LED will light up, indicating it is ready to use with the new firmware.

Uploaded by

kgskgm
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 5

Working with DownLoader service program The program SuperDL.exe is in the Download.zip. Extract the file in a directory.

File *.zip you have to extract it on your ! in a directory. ". ower on the !. #. ower on the $o!on device. %. !onnect the device and ! via optical head ca&le. '. Dou&le(clic) on the file Super-DL.exe. *n the screen you will see the main window of program+ shown on fig. ".

Fig. ", -ain window .. From the main window /fig. #0 push the &utton, . *n the ! screen you will see the window+ shown on fig. #. There is a list with !*- ports of your ! /!*-"+ !*-#+ !*-%+ !*-'0. 1ou have to mar) that !*- port which you have connected the device &y the optical head ca&le. 2ext push the !onnect(&utton and on your ! screen you will see the message that the connection is done or not connection.

Fig. #

6. The device have to &e set in System mode in following way, ower(*FF the device. *n the device front face panel push -button and power-ON the device.
The device is in system mode (the display shows blank screen and Ready-LED is o .

3. From the main window push this &utton shown on fig. #. !lic) 41ES5 &utton.

. 1ou will see the message+

Fig. # 6. 1ou will see the window+ shown on fig. % a0. -ar) the needed file 4 *.bin5 and clic) 4*pen5 &utton. 7. 1ou will see the message+ shown on fig. % &0. ush 4*85 &utton. "9. *n the enclosed area on fig. ' will see telegrams /receive and send telegrams0. So if you see these telegrams+ the rocedure is started.

Fig. % a0 ATTE T!" #### !t is ver$ important which %i&e $ou have to down&oad. '&s.( check the second disp&a$ o% )*! +,-. : F#'r;'2 : " 9'.9;.96<"', .= The red number /0+1 means that the processor is 0+ 234. *i&es %or 0, 234 and %or 0+ 234 are. )5+v0+m.bin )5+v0,m.bin

Fig. % &0

Fig. ' "". Displaying on your ! screen the message+ shown on fig. .+ means that the rocedure is finished. ush 4*85 &utton here.

Fig. . "#. From the main window push this &utton . *n your ! screen you will see the message+ shown on fig. ;. ush 41ES5 &utton. "%. 1ou will see the message 4Start is done successfully5. ush 4*85 &utton.

Fig. ; *n the device you will see that the 4$eady5 LED lights up /green LED0+ so the devise is ready.

You might also like