Scribd
Upload
166 views

Can A Water Pump Explode

Water pump

Uploaded by

Himanshu Chichra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
166 views

Can A Water Pump Explode

Water pump

Uploaded by

Himanshu Chichra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Before starting any pump, check that all valves are in

the correct position. Be sure that the valves in the


intended flow path are open, and other valves, such as
drains and vents, are closed.
If you are starting a pump from a remote location such
as a control room, be sure that the pump is ready for
operation. If you are not sure, go to the pump and check
it, or have somebody else check it.
Make sure that key steps important for safe operation
of pumps, including all valve positions, are included in
your plant operating procedures and checklists.
See the October 2002 Process Safety Beacon for a similar incident.
What can you do?
The answer must be yes or we wouldnt have a subject for this Beacon! The centrifugal pumps in the pictures are
all water pumps which exploded. The explosions did not occur because of any contamination or chemical reaction with
something that was not supposed to be in the pump. In fact, explosions like this have happened with very pure water
boiler feed water pumps, condensate pumps, and deionized water pumps.
How did these explosions happen? The pumps were operated for some period of time with both the pump suction and
discharge valves closed. Because water could not flow through the pump, all of the energy which normally goes into
pumping is instead converted to heat. When water is heated, it expands generating hydrostatic pressure inside the pump.
This may be enough pressure to cause the pump to fail perhaps the seal would fail, or the pump casing might rupture.
These explosions may cause significant damage or injuries because of the built-up energy. However, if the water
exceeds its boiling point before the pump fails, a more energetic explosion may occur because the released superheated
water will rapidly boil and expand (a boiling liquid expanding vapor explosion - BLEVE). The severity and damage will
be similar to a steam boiler explosion.
This type of explosion can happen with any fluid if a pump is operated with suction and discharge valves closed. If a
non-hazardous fluid like water can result in the damage shown in the pictures, think how much more severe the damage
might be if the fluid is flammable - the released material could catch fire. If the fluid is toxic or corrosive, people near
the pump could be severely injured by the released material.
http://www.aiche.org/CCPS/Publications/Beacon/index.aspx
Messages for Manufacturing Personnel
Don t let your pumps run while blocked in!
AIChE 2013. All rights reserved. Reproduction for non-commercial, educational purposes is encouraged. However, reproduction
for the purpose of resale by anyone other than CCPS is strictly prohibited. Contact us at [email protected] or 646-495-1371.
Can a water pump explode?
The Beacon is usually available in Arabic, Afrikaans, Chinese, Czech, Danish, Dutch, English, French, German, Greek, Gujarati, Hebrew, Hindi, Hungarian, Italian, Japanese,
Korean, Malay, Marathi, Norwegian, Persian, Polish, Portuguese, Romanian, Russian, Spanish, Swedish, Telugu, Thai, Turkish, and Vietnamese.
www.aiche.org/ccps
August 2013
This issue sponsored by
www.iomosaic.com
Some pumps are started automatically for example
by a process control computer or a level instrument to
automatically empty a tank when it is filled. Make sure
that all of the valves are in the correct positions when
putting these pumps into automatic operation, for
example, after maintenance.
Some pumps have instrumentation installed to prevent
running while blocked in for example, low flow, high
temperature, or high pressure interlocks. Be sure that these
safety systems are properly maintained and tested.

You might also like