SURATGARH, STAGE-V, UNIT # 7 & 8

(2 x 660 MW) THERMAL POWER

TECHNICAL SPECIFICATION
FOR
FLOW ELEMENT ASSEMBLY- ORIFICE



VOLUME II-B


SPECIFICATION Nos
PE-TS-392-145-I 005A





BHARAT HEAVY ELECTRICALS LIMITED
POWER SECTOR
PROJ ECT ENGINEERING MANAGEMENT DIVISION
NOIDA, INDIA





PREAMBLE
SPECIFICATION NO. PE-TS-392-145-I005A
VOLUME II-B
SECTION A
REV NO. 00
SHEEET . OF .


1.0 The tender document contains three (3) volumes. The bidder shall meet the requirements of all the
three volumes.

1.1 Volume-I (CONDITIONS OF CONTRACT)

This consists of four parts as below :-
Volume-IA : This part contains instructions to bidders for making bids to BHEL.
Volume-IB : This part contains general commercial conditions of the tender & includes provision
that vendor is responsible for the quality of item supplied by their sub-vendors.
Volume-IC : This part contains special conditions of contract.
Volume-ID : This part contains commercial conditions for erection & commissioning site work,
as applicable.

1.2 Volume-II TECHNICAL SPECIFICATIONS

Technical requirements are stipulated in Volume-II which comprises of :-
Volume-IIA : General Technical Conditions
Volume-IIB : Technical Specification including Drawings, if any.

1.2.1 Volume-IIB

This volume is sub-divided into following sections :-
Section-A : This section outlines the scope of enquiry.
Section-B : This section provides Project Information.
Section-C : This section indicates technical requirements specific to the contract, not
covered in Section-D.
Section-D : This section comprises of technical specifications of equipments complete with
data sheet A, B and C.

Data Sheet - A specifies data and other requirements pertaining to the Equipment.

Data Sheet - B Specifies data to be filled by the bidder (Data Sheet-B is contained
in Volume-III).

Data Sheet - C Indicates data/documents to be furnished after the award of contract as
per agreed schedule by the vendor (as applicable).

1.2.2 Volume-III TECHNICAL SCHEDULES

This volume contains technical schedules and Data Sheets-B, which are to be duly filled by the bidder and the
same shall be furnished with the technical bid as per instructions given in Document No. PE-SS-999-100-Q-002
in Volume-III.

2.0 The requirements mentioned in Section-C / Data Sheets-A of section-D shall prevail and govern in case of
conflict between the same and the corresponding requirements mentioned in the descriptive portion in
Section-D.



REPARED BY
VM RAO, DGM (Q)
APPROVED BY :
RAJIVA K SOOD, AGM & MR
SDM_files labelled.doc
Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I005A

VOLUME II-B
SECTION
REV. NO. 00 DATE: 07.04.2014


SHEET of 1




BHEL - PS-PEM : NOIDA 201301



Technical specification for
FLOW ELEMENT ASSEMBLIES
(Orifice & Nozzle)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

CONTENTS

VOL-II B


SECTIO
N

DESCRIPTION

No of
sheets
A Scope of Enquiry 1
B Project Information 3
C Specific Technical Requirements
- General Requirements 5
D Specification for Flow Elements
- Equipment Specification ( PES 145 05 ) 5
- Data sheets A & B for Flow Elements- ORIFICE.
(Data sheet no. PES-145-05-DS1-0)
22
- Data sheets C for Flow Elements- ORIFICE
(Data sheet no. PES-145-05-DS2-0)
2
- Quality Plan for Flow Orifice Plate 2
- Bill of Quantity for Flow Elements with spares. 1
- Schedule of submission of Drawings/Documents, Equipment
Manufacture, Inspection and Dispatch.
1

Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A

VOLUME II-B

SECTION A
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
FLOW ELEMENT ASSEMBLIES
(Orifice)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER PROJECT

SECTION A


SCOPE OF ENQUIRY




Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I005A


VOLUME II-B

SECTION A
REV. NO. 00 DATE: 07.04.2014


SHEET 1 OF 1








Technical specification for
FLOW ELEMENT ASSEMBLIES
(Orifice)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER PROJECT
SCOPE OF ENQUIRY
1.0 SCOPE
This specification covers the Design, Manufacture, Inspection and Testing at manufacturers
works, proper packing for transportation and delivery to site of the Flow Element Assemblies
along with Accessories, Start-up/Commissioning spares as mentioned in different sections of
this specification for 2 X660 MW SURATGARH THERMAL POWER project.
.1 The quality plan enclosed forms the minimum requirement but not limited to be adhered to
by the bidder.

.2 The enquiry shall be operated in COMPLAINCE MODE means bidder to comply with the
requirement of specification, quality plan, delivery schedule, quantities, start-
up/commissioning spares, mandatory spares, recommended spares etc, and as a token of
acceptance of the same, following formats to be signed, stamped with company seal and
submitted separately for each project.

a) Compliance certificate
b) Quality plan
c) Schedule of submission of drawings / documents, equipment manufacture inspection
and dispatch
d) Schedule of price, unit prices, inspection schedule
.3 No separate technical offer, data sheets to be submitted with the bid. Any such
document shall not be taken cognizance of, and document (Compliance certificate)
at 3a above shall be final and binding. Data sheets shall be furnished by the
successful bidder (vendor), only after the award of contract.
.4 Bidder to note that CALIBRATION TEST is required to be conducted on one type per
size, Bidder to group such assemblies and indicates the same along with the price
bid. Unpriced portion to be submitted.
2.0 GENERAL TECHNICAL INSTRUCTIONS
1 It is not the intent here to specify all the details of design and manufacture. However,
the equipment shall conform in all respects to high standard of design, engineering and
workmanship and shall be capable of performing the required duties in a manner
acceptable to the customer / consultant, who will interpret the meaning of drawing and
specification and shall be entitled to reject any component or material which in his
judgment is not in full accordance herewith.

2 The omission of specific reference to any component / accessory necessary for the
proper performance of the equipments shall not relieve the supplier of the responsibility
of providing such facilities to complete the supply within the quoted prices.

3 BHELs / Customers representatives shall be given access to the shop in which the
equipments are being manufactured or tested and all test records shall be made
available to them.

4 The Equipment covered under this specification shall not be dispatched unless the
same have been finally inspected, accepted and Material Dispatch Clearance Certificate
(MDCC) is issued by BHEL/ Customer.










SECTION: B
PROJECT INFORMATION



SPEC.NO.
TCE.5750A-H-500-001
TATA CONSULTING ENGINEERS LIMITED
VOLUME II
SECTION B

RRVUNL, 2 x 660 MW, Super-Critical TPS, Stage-V,
Unit # 7 & 8 at Suratgarh, Rajasthan
GENERAL PROJECT INFORMATION
SHEET 1 OF 3

FORM NO. 329 R5
ISSUE
R1

1.0 Owner Rajasthan Rajya Vidyut Utpadan
Nigam Ltd., Jaipur

2.0 Consulting Engineer TATA Consulting Engineers Ltd.
73/1, St. Marks Road,
Bangalore 560 001

Tel : 080 6622 6000
Fax : 080 22274874

3.0


4.0
Location of the plant


Latitude and longitude
Prabat Nagar, Suratgarh
Sriganganagar district, Rajasthan.

Latitude : 29 deg. 10 min. N
Longitude : 74 deg.01 min. E

5.0 Elevation above mean sea level 186 m (approximate)

6.0 Climatic conditions
6.1 Temperatures : Monthly basis

Mean of daily max. 32.8 deg.C (in the month of May)
Mean of daily min. 17.6 deg.C (in the month of Jan)

6.2 Temperatures : Annual basis

Mean of daily max. 32.3 deg.C
Mean of daily min. 19.6 deg.C

Highest temperature recorded 50 deg.C

Lowest temperature recorded (-) 2.8 deg.C
Design Ambient Temperature for
Electrical Equipment design
50 deg C

6.3 Relative humidity Varies between 21% and 81%

6.4 Annual average rain fall 312 mm

6.5 Annual mean wind speed : 4 km / hr.
7.0 Wind load
SPEC.NO.
TCE.5750A-H-500-001
TATA CONSULTING ENGINEERS LIMITED
VOLUME II
SECTION B

RRVUNL, 2 x 660 MW, Super-Critical TPS, Stage-V,
Unit # 7 & 8 at Suratgarh, Rajasthan
GENERAL PROJECT INFORMATION
SHEET 2 OF 3

FORM NO. 329 R5
ISSUE
R1

Calculations for wind effect shall be in accordance with IS:875-1987(Part-3)
taking into account the following:

a) Basic wind speed = 47 m/sec
b) Factor K1 = 1.07
c) Category of terrain = Category 2
d) K3 as per IS 875
8.0 Seismic data (As per IS: 1893 latest issue)

a) Zone Zone II

Designs & design coefficients shall be based on IS 1893:2002

Design condenser cooling water
inlet temperature
33 Deg C

9.0 Auxiliary power supply:


Auxiliary electrical equipment to be supplied against this specification shall be
suitable for operation on the following system:

a)


b)


c)
For motors rated 160 kW and
below.

For motors rated above 160 kW
and up to 1500 kW

For motors rated above 1500kW

415V AC, 3-phase, 3-wire effectively
earthed.

6600V AC, 3-phase, 3-wire, 50 Hz, non-
effectively earthed

11000V AC, 3-phase, 3-wire, 50 Hz,
non-effectively earthed
d) For motor control centres 415V AC, 3-phase, 3/4-wire effectively
earthed.
e) DC motor starters, DC solenoids,
DC alarm control and protection
220 V DC, 2-wire unearthed
f) AC control & protective devices 110 V 1 phase, 50Hz, 2 wire AC supply.
The single phase 110V AC supply shall
be derived by VENDOR by providing
415V / 110 V Control transformers of
adequate rating with MCCB / MCB on
both the primary and secondary sides.
g) Uninterrupted power supply 230 V, 1-phase, 50 Hz, 2-wire, AC
SPEC.NO.
TCE.5750A-H-500-001
TATA CONSULTING ENGINEERS LIMITED
VOLUME II
SECTION B

RRVUNL, 2 x 660 MW, Super-Critical TPS, Stage-V,
Unit # 7 & 8 at Suratgarh, Rajasthan
GENERAL PROJECT INFORMATION
SHEET 3 OF 3

FORM NO. 329 R5
ISSUE
R1
supply (For all instrumentation and
control system equipment and solenoid
valves)


g) Lighting fixtures and space heaters

240 V, 1 phase, 2 wire, 50Hz,solidly
earthed system
h) Construction supply 415 V, 3 phase, 4 wire, 50Hz AC
supply with neutral lead solidly earthed.

i) The above voltages may vary as follows :

All devices shall be suitable for continuous operation over the entire range of
voltage and frequency indicated below without any change in their
performance.

AC supply Voltage variation 10%
Frequency variation 5%

Combined voltage & frequency
variation 10%
DC supply Voltage variation +10% ,-15%
j) For instrument and control system
of steam generator and steam
turbine generator.
230 V 5% AC UPS, 1-phase, 50 Hz,
2-wire. The 24 V DC required for
control system shall be generated from
this UPS.

10.0 All the electrical equipment shall be designed for 50 C reference ambient
temperature.




Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION C
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SECTION C


SPECIFIC TECHNICAL REQUIREMENTS




Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION C
REV. NO. 00 DATE: 07.04.2014


SHEET OF








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SPECIFIC TECHNICAL REQUIREMENTS for the project.

The requirements in this section are specific for this project and shall over-ride the
specification under section-D in case of any contradiction.


1. Thickness of Orifice Plate shall be 3.00 mm for main pipe dia up to 300 mm, and above pipe
dia of 300 mm the same shall be 6.00 mm.

2. Calibration of the Flow nozzles shall be as per ASME PTC 19.5, however for Orifice plates
shall be as per BS 1042.

3. Hydraulic test pressure for Assemblies shall be 1.5 times of the design pressure at normal
temperature.

4. Inspection shall be carried out in line with the approved drawings / data sheets / QP and
specific technical requirements.

5. Acceptance norm for surface finish after machining for both pipe, nozzle is the requirements
as specified in PTC 19.5.

6. Bidder to note that data sheet-B, Format Schedule of submission of Drawings /
Documents, Equipment Manufacture, Inspection and Despatch enclosed in Section-
D, to be signed and stamped and submitted with the bid. Quality Plan enclosed in
Volume-IIB should be furnished duly signed and stamped.

7. All the formats in Volume-III should filled-up and furnished with the bid, complete in all
respect.In the absence of those, the bid would be considered incomplete and liable for
rejection.

8. Wherever IBR certification is required as per data sheet for an element, all accessories
pertaining to that element shall require IBR Certification.

9. SPARES : The following spares are required to be offered

(A) Mandatory Spares:
The items listed in list of mandatory spares attached at section-D, of this
specification, are the essential spares required to be offered by the bidder,
and the price for which (Lump sum as well as individual) for each item to be
quoted separately under the separate heading. The format for price schedule to
be filled-up by the bidder is enclosed in Volume-III

Each Case / Container containing Mandatory spares shall be clearly marked or
labelled on the outside with the description of the spares contained in it. When
more than one item of spare parts are packed in a single Case / Carton, a
general description of the contents shall be shown outside of such case, and
detailed list enclosed. All Cases, Containers and Packages must be suitably
marked and numbered for the purpose of identification.
Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION C
REV. NO. 00 DATE: 07.04.2014


SHEET OF








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER


(B) Recommended Spares:
In addition to the Mandatory spares mentioned, the bidder shall also furnish a
List of Recommended spares if for 3 years of normal operation of the Flow
Element Assemblies. The BHEL reserves the right to buy any or all of the
recommended spares.
(C) Start-up & Commissioning Spares:
Start-up and Commissioning spares are those spares, which may be required
during the start-up and commissioning of the Flow Element Assemblies. All
start-up spares, which are supplied under this contract, shall be strictly
interchangeable with the parts for which they are intended for replacements.
The format for price schedule to be filled-up by the bidder is enclosed in
Volume-III
The Start-up and commissioning spares indicated by the bidder shall be a part
of the main Flow Element Assembly supplies. However bidder to indicate prices
separately. The list of these spares required is enclosed in the section-D of this
specification.
10. Documentation :
(A) Along with the bids: following documents for respective projects separately
a) Signed and stamped compliance certificates in attached format (VOL.-
III).
b) Schedule of prices in attached format (VOL.-III).
c) Schedule of submission of Drg. / Doc, Equip. Manufacture, Inspection and
Dispatch.
d) Inspection schedule
(B) After the award of contract :
The documentation as listed below to be submitted, separately for respective projects.

6 sets of the following documents + 3 sets of Floppies / CDs to be submitted for
Approval:
a. Assembly drawing of all type of Flow Element assemblies complete with all
accessories indicating detailed dimensions, BOM and weights.
b. Flow Element Edge preparation details.
c. Installation drawings for the flow elements.
d. Technical Data sheet-C completely filled-up..
Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION C
REV. NO. 00 DATE: 07.04.2014


SHEET OF








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER
e. Quality Plan duly signed and stamped.
f. Bore size calculations for Flow orifices and Flow Nozzles for all the conditions
indicated in the data sheets.
g. Differential Pressure Vs Flow, curve for each Orifice and Nozzle.
h. All relevant catalogues for the models of the Flow Element Assemblies as well as
accessories finalized.
i. Bar chart to indicate the time schedule for procurement, manufacture, testing and
dispatch.
(C) Final documentation :

1. Category I & IV Approved final drawings/data sheets, 20 sets with 4 CD-ROMS
Bore sizing calculations, DP Vs Flow Curve for each
Orifice and Nozzle.

2 Test certificates 20 sets.

3. Operation & Maintenance Manuals 20 sets with 4 CD-ROMS
for Flow Element Assemblies and all the
Accessories.

Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I005A


VOLUME II-B

SECTION C
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
ORIFICE

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER




CUSTOMER SPECIFICATION




SPEC.NO.

TCE.5750A-H-500-001
TATA CONSULTING ENGINEERS LIMITED
VOLUME V
SECTION : D5.4
Package: EPC
RRVUNL, 2 x 660 MW, Super-Critical TPS, Stage-V,
Unit # 7 & 8 at Suratgarh, Rajasthan
INSTRUMENTATION AND CONTROL EQUIPMENT
SPECIFICATION FOR INSTRUMENTATION &
CONTROL EQUIPMENT

SHEET 4 OF 42


ISSUE
R1
TCE FORM 329 R5
FILE NAME: SEC D5.4.DOC
1.11 Flow Glasses

Online flow glasses for pipe size up to 6 with a rotary wheel (not a flapper type)
suitable for installation on vertical or horizontal pipelines, material Pyrex tempered
glass. Body material shall be carbon steel, rotor & wetted parts shall be bronze. The
material of accessories shall be SS. IP 65 or equivalent degree of protection for
enclosure. Upto 50 Nb size, connection shall be screwed & above 50 mm Nb size it
shall be flanged - ANSI, 150 RF. Accessories like name plate, mating flanges with
gaskets (neoprene), bolts & nuts, etc. shall be supplied.

1.12 Flow Switches

Indicating, Differential pressure, flapper type on line flow switches for line sizes up to
80 mm with an accuracy of +/-0.5% of span and dial size of min. 50 mm having 316
SS flapper/SS 316 bellows housed in die cast aluminium. Micro switch with adjustable
range with 2 SPDT contacts rated for 0.2 A, 220 V DC. IP 65 or equivalent degree
of protection for enclosure. The material of accessories shall be SS. Repeatability
shall be
+/-0.5% of span. Over range protection shall be 50% above maximum flow. Setting
shall be tamper proof external adjustment & scale shall be provided for setting.
Range spring & orifice plate shall be SS 316 for DP type. NPT for sizes below 2 & for
sizes above 2 ANSI 150 RF shall be provided. Accessories like nameplate, mating
flanges with gaskets, bolts & nuts, pipe assembly with orifice plate, etc. 5 way manifold,
pipe, fittings (DP type), etc. shall be supplied.

1.13 Flow Elements

316 SS long radius, welded type flow nozzles as per ASME PTC 19.5 or BS-1042 for
all steam and feed water services with D and D/2 pressure tappings; 316SS
concentric orifice plate assembly as per ASME PTC 19.5 or BS-1042 for all water
services with flange tap connections. Beta ratio of 0.34 to 0.7 for orifice and around 0.7
for flow nozzles.. The material of accessories shall be SS. Refer to Table-5 for provision
of flow elements. All the flow elements shall have 3 pairs of differential pressure
tappings complete with root valves. Orifice plate shall be3 mm thick for nominal pipe
diameter upto 300 mm & 6 mm thick for pipe diameter > 300 mm. The thickness of the
flow nozzle shall be as per the application. The flow elements shall be supplied as
assemblies with High/low pressure tappings, root valves as required. Performance
Guarantee flow elements shall be provided separately. Butt welded edges shall be
prepared as per ANSI 16.25 & flanged connections shall be as per ANSI 16.5
standards. Orifice assembly complete with nipples & valves to be supplied by Bidder
shall be one meter long with ANSI class 150 RF SS flanges at the ends including
gaskets, bolts & nuts. Isolating valves shall have SW end connection. Accessories
like nameplate, gaskets, bolts & nuts, reservoirs (condensing chambers), 6 nos. shut
off valves per assembly, nipple, welding adapters, etc. shall supplied. Bidder shall
submit assembly drawing and flow vs DP curve for each flow element.
Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION D
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SECTION D

EQUIPMENT SPECIFICATION
DATA SHEETS A & B
DATA SHEETS - C
QUALITY PLAN
BILL OF QUANTITY
(INCLUDING SPARES)
SCHEDULE OF SUBMISSION OF
DRAWINGS /DOCUMENTS,
EQUIPMENT MANUFACTURE,
INSPECTION AND DISPATCH







Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION D
REV. NO. 00 DATE: 09.04.2014



SHEET









Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SECTION D


EQUIPMENT SPECIFICATION
(PES 145 05)







SPECIFICATION FOR FLOW MEASURING
DEVICES (ORIFICE )
SPECIFICATION NO.: PES 145 - 05
VOLUME II B
SECTION D
REV. NO. 00 DATE 05.04.2014
SHEET 1 OF 5

F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


1.0 SCOPE

This specification covers the design, manufacture, inspection and testing at the manufacturers works,
proper packing for transportation and delivery to site of flow measuring devices (orifices & nozzles) for
use in Utility/Captive Power Station/Combined Cycle Station.

2.0 CODES AND STANDARDS

2.1 All the equipment specified herein shall comply with the requirements of the latest issue of the relevant
National and International standards.

2.2 The Design and Materials used for the components shall also comply with the relevant National and
International standards.

2.3 As a minimum requirement, ASME PTC 19.5 standard shall be complied with for Flow Nozzles and BS
1042 / ISO 5167 for Flow Orifices.

3.0 TECHNICAL REQUIREMENTS

The orifice plates and flow nozzles shall be used as the primary flow sensing elements. These sensing
elements shall provide a safe and reliable means of creating differential pressures for use in flow
measurements.

3.1 Orifice Plates

The orifice plate assemblies shall conform to the following requirements unless specified otherwise in
the corresponding data sheets.

3.1.1 Type : The Orifice plates shall be of concentric type, designed and manufactured as per ASME PTC
19.5. The data sheet enclosed, specifies the requirements of each orifice plate assembly. The bidder
shall calculate the Beta ratio and validate suitability of the selected design for the specified application,
Vent holes, if required for the specified duty shall be located at the top and drain holes at the bottom of
the orifice.

3.1.2 Material : The material of the Orifice plates shall be stainless steel type SS 316 .

3.1.3 Assembly : Orifice plates shall be supplied as complete assemblies, along with companion flanges on
both sides having proper end connection for welding on to the associated pipe at site, gaskets, nuts
& bolts. The carrier ring assembly shall be supplied if specified in the data sheet.

In case when branch pipe (as in 3.2.4 below) is specified in the data sheet, the orifice will be welded
within the branch pipe. For application of SH/RH attemperation, welded type orifice shall be used.

Each flow orifice assembly shall be provided with three pairs of pressure tapping complete with
associated root valves, suitable for the service conditions. The pressure tapping shall be provided either
on the carrier ring or on the companion flanges as the case may be. 2 Nos Root Valves shall be
provided for normal pressure above 40 ata.

Each orifice plate or the carrier ring assembly (as the case may be) will also be provided with a
extended handle. The Tag No. and duty will be permanently marked on both the sides of this handle.

SPECIFICATION FOR FLOW MEASURING
DEVICES (ORIFICE )
SPECIFICATION NO.: PES 145 - 05
VOLUME II B
SECTION D
REV. NO. 00 DATE 05.04.2014
SHEET 2 OF 5

F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


.

3.1.4 Flanges : The Companion flanges shall conform to ANSI B16.5. The companion flange and the carrier
ring material shall be same as that of the main pipe. These shall be manufactured from forged material.
Companion flanges shall be suitably rated for the specified service conditions.

3.1.5 While machining the ID to maintain an uniform internal diameter, care shall be taken to ensure the
minimum thickness of the branch pipe as per IBR regulations.

3.2 Flow Nozzles

The Flow nozzle assemblies shall conform to the following requirements unless specified otherwise in
the corresponding data sheets.

3.2.1 Type : The Flow nozzles shall be of long radius, weld in type (suitable for welding with the associated
branch pipe). The design and manufacture of the flow nozzles shall be as per ASME PTC 19.5. The
data sheet enclosed, specifies the requirements of each flow nozzle assembly. The bidder shall
calculate the Beta ratio and validate suitability of the selected design for the specified application. Vent
holes, if required for the specified duty shall be located at the top and drain holes at the bottom of the
nozzle.

3.2.2 Material : The Flow nozzles shall be constructed of stainless steel type SS 316 .

3.2.3 Assembly : The Flow nozzles shall be supplied as complete assemblies, along with duly machined
branch pipes, having proper end connection for welding on to the associated pipe at site. Welding
shall be done as per the relevant ANSI practice in line with the main piping.

Each flow nozzle assembly shall be provided with three pairs of pressure tapping complete with
associated root valves, suitable for the service conditions. D & D/2 pressure tapping shall be provided
on the branch pipe. The size of root valve should not be less than 15 NB. Two numbers of root valves
to be provided for pressure >40Kg/Cm
2
for each tapping.

Each flow nozzle assembly will also be provided with a suitable nameplate, with tag number and duty.

3.2.4 Branch pipe: The branch pipe for mounting the flow Nozzle/Orifice will be supplied as a free issue item
by the purchaser. However the successful bidder shall collect the branch pipe from any of BHEL Units
or Site, to be intimated by the purchaser during contract stage. The vendor shall be responsible for
proper transportation from the above collection point, machining of the branch pipe and welding the flow
nozzle/orifice inside the branch pipe. Acquiring of IBR certification if required shall also be the
responsibility of the successful bidder. Bidder to note that the branch pipe supplied by BHEL, may have
tolerance as per ASTM standard (i.e. OD 1% (Max. 4 mm), wall thickness 12.5%). The cost of all such
activities shall be included by the bidder in the offer.

3.2.5 While machining the ID to maintain uniform internal diameter, care shall be taken to ensure the
minimum thickness of the branch pipe as per IBR regulations.

3.3 Guarantee & Performance

The guarantee for the flow orifice and the flow nozzle assemblies shall be for 12 months continuous
operation from the date of commissioning.


SPECIFICATION FOR FLOW MEASURING
DEVICES (ORIFICE )
SPECIFICATION NO.: PES 145 - 05
VOLUME II B
SECTION D
REV. NO. 00 DATE 05.04.2014
SHEET 3 OF 5

F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


4.0 TESTS & INSPECTION

4.1 The equipment covered under this specification shall be subject to vendors quality plan to be approved
by the purchaser before start of manufacture. To ensure that quality is in-built in each equipment the
quality assurance system manual indicating the system followed by the vendor shall be submitted to
purchaser for his review.

4.2 The quality plan forming part of this specification shall be the minimum requirements for the vendors
quality plan to be submitted with the offer. The vendor shall give at least 15 days written notice to
purchaser for witnessing the tests/inspection at various stages. The expenses for all such
tests/inspection shall be to manufacturers account except for the expenses of purchasers
representatives witnessing the tests. The purchaser shall attend such tests/inspection within 15 days
failing which the manufacturer may proceed with the tests which shall be deemed to have been made in
purchasers presence and shall furnish relevant test certificates to the purchaser.

4.3 One orifice plate and one flow nozzle of each type and size shall be tested and calibrated by the bidder
at customers approved laboratory, within his quoted price. Details of the calibration test i.e, type of
test, equipments employed etc. shall be submitted in the bid.

4.4 Each branch pipe shall be inspected by the purchaser after the completion of machining and prior to
welding of the nozzle. This test will include dimensional checks, surface smoothness checks etc.

4.5 IBR certification, if required for the specified service shall be obtained by the successful bidder from the
concerned authority for submission to the purchaser.

4.6 The Standard QP is included in this specification to enable bidder to understand the extent of inspection
and testing requirements to execute this job. The successful bidder has to follow the agreed QP, taking
care of customer requirements mentioned in Sec-C and submit QP for final approval by BHEL /
Customer.

5.0 SPARES

5.1 The offer shall include a list of all the recommended spares offered, for the flow elements and
accessories required for 3 years of operation, until & unless specified.

5.2 The offer shall include a list of all the commissioning spares offered, which are required for
commissioning of the flow elements & accessories and the cost of which shall be included in the
bidders price.

5.3 The offer shall include a list of mandatory spares , which is required for the guarantee period. The cost
of these mandatory spares shall also be included in the price of the flow element assemblies and
accessories.

5.4 The spares shall also include one set of maintenance kit including special tools, if required.

6.0 DRAWINGS & DOCUMENTS

6.1 To be furnished with the Bid:

The offer shall include the following technical documents in 5 copies each :

1. Technical data sheets for each flow element and accessories, in the proforma enclosed under
Data sheet-B.

2. Catalogues/Technical literature for flow element and accessories.


SPECIFICATION FOR FLOW MEASURING
DEVICES (ORIFICE )
SPECIFICATION NO.: PES 145 - 05
VOLUME II B
SECTION D
REV. NO. 00 DATE 05.04.2014
SHEET 4 OF 5

F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


3. List of installations for similar equipment supplied in Thermal Power Station applications.

4. Schedules listed under Vol. III-A duly completed with bidders signature and seal.

5. Bar chart.

6. Test & Inspection schedules.

7. Details of calibration tests i.e, type of tests, equipments employed for the testing of the flow
elements, together with the name of the laboratories where these tests can be conducted.

8. The calculation of proper flow orifice and flow nozzle bore for the process conditions indicated in
the data sheet.

9. Assembly drawing of each type of flow elements with detailed dimensions, B.O.M. and weights.

10. Deviations sought by bidder, if any, from the specification.

6.2 To be furnished after award of contract

6.2.1 For approval:

1. Technical data sheets for each flow element and accessories, in the proforma enclosed under
Data sheet-B.

2. The calculation of proper flow orifice and flow nozzle bore for the process conditions indicated in
the data sheet.

3. Assembly drawing of each type of flow elements complete with all accessories indicating
detailed dimensions, B.O.M. and weights.

4. Detailed dimensional drawings of each flow orifice, companion flanges, carrier ring, root valves,
flow nozzles, branch pipes, pressure connections, nipples etc.

5. Detailed dimensional drawings of each flow orifice, companion flanges, carrier ring, root valves,
flow nozzles, branch pipes with edge preparation details, pressure connections, nipples etc.

6. Installation drawings for the flow elements.

7. Differential pressure vs flow curve for each Orifice and Nozzle.

6.2.2 For information:

1. Storage & commissioning instructions.

2. O&M manuals are to be supplied in 10 copies.


SPECIFICATION FOR FLOW MEASURING
DEVICES (ORIFICE )
SPECIFICATION NO.: PES 145 - 05
VOLUME II B
SECTION D
REV. NO. 00 DATE 05.04.2014
SHEET 5 OF 5

F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0



7.0 PACKING & MARKING

7.1 Packing: Each orifice plate & nozzle assembly and the associated accessories shall be packed
properly with adequate protection against friction, stresses, vibrations and shocks during transportation.
Each packing shall have markings as per Purchase Order / Special Condition of the Contract (SCC).

7.2 Marking: Each flow element assembly shall be identified with the following information:

- Tag Number

- Service

- Element Material

- Beta ratio

- Line size & thickness

- Direction of flow


8.0 APPLICABLE DATA SHEET FORMS

This document shall be read with one or more of the following data sheet forms :

- Data sheet A&B for Flow Measuring Devices
(Orifice & Nozzle) : Data sheet no. PES-145-05-DS1-0

- Data sheet C for Flow Measuring Devices
(Orifice & Nozzle) : Data sheet no. PES-145-05-DS2-0


Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION D
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)
SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SECTION D



DATA SHEETS A & B







BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 4 OF 43

4

Tag No. : LCA01 BP 001, LCA02 BP 001, LCA03 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRVUNL-2x660 MW SURATGARH STPP, STAGE-V
Bidder to specify
03 PER UNIT (ONE AGAINST EACH TAG NO.)
CEP A/B/C DISCHARGE FLOW
Bidder to specify






ELEMENT

TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE


[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE [] BEVEL EDGE [] CARRIER
RING
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA
[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300# : ASTM A105
[] YES [] NO
Not Applicable
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE [] ON PIPE [] ON CARRIER
RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800
15NB/SS/SCH.40/12 NOS. ; 250mmLONG
Not Applicable






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM2 (A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] CW [] OTHER
MAX. NORMAL MINIMUM
(PumpDesign) (VWO)(Min.Recirculation)
880 780 290
35 35.8 40.9
46.5 46.5 39.6
45Kg/cm
2
(g):60
o
C
0.5Kg/cm
2
atmax.flow
Bidder to specify














BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 5 OF 43

5

Tag No. : LCA01 BP 001, LCA02 BP 001, LCA03 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
323.9 x 9.53
SA 106 GR B
Bidder to specify
15 D

10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

NAME
SIGNATURE
DATE
PREPARED BY CHECKED BY APPROVED BY
COMPANY SEAL


NAME
SIGNATURE
DATE
SSV

13/06/2013

IJ S

13/06/2013

IJ S

13/06/2013


NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED AT 880 T/HR & 290 T/HR FLOW VALUES.
2. RECOMMENDED RANGE IS 0 1000 T/HR.
3. 3 NOS. OF S-BAND SHALL BE REQUIRED FOR EACH TAG

.




BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 6 OF 43

6

Tag No. : LCA20 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRVUNL-2x660 MW SURATGARH STPP, STAGE-V
Bidder to specify
ONE (1) PER UNIT
CONDENSATE FLOW D/S OF GSC
Bidder to specify






ELEMENT

TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE


[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE [] BEVEL EDGE [] CARRIER
RING
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA
[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300 : ASTM A105
[] YES [] NO
Not Applicable
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800
15NB/SS/SCH.40/12 NOS. ; 250mmLONG
Not Applicable






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM2 (A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] CW [] OTHER
MAX. NORMAL MINIMUM
(PumpDesign) (VWO)(GSCMin.Flow)
1800 1556 324
33.8 34.8 40.5
52 50 45
45Kg/cm
2
(g):60
o
C
0.5Kg/cm
2
atmax.flow
Bidder to specify














BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 7 OF 43

7


Tag No. : LCA20 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
457 x 12.7
SA 106 GR C
Bidder to specify
15 D
10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

NAME
SIGNATURE
DATE
PREPARED BY CHECKED BY APPROVED BY
COMPANY SEAL


NAME
SIGNATURE
DATE
SSV

13/06/2013

IJ S

13/06/2013

IJ S

13/06/2013


NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED AT 1800 T/HR& 324 T/HR FLOW VALUES.
2. RECOMMENDED RANGE IS 0 2200 T/HR.




BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 8 OF 43

8


Tag No. : LCA92 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRVUNL-2x660 MW SURATGARH STPP, STAGE-V
Bidder to specify
ONE (1) PER UNIT
CONDENSATE FLOW TO DEAERATOR
Bidder to specify






ELEMENT

TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE


[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE [] BEVEL EDGE [] CARRIER
RING
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA
[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO













END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI-300# : ASTM A 105
[] YES [] NO
Not Applicable
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE [] ON PIPE [] ON CARRIER
RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800
15NB/SS/SCH.40/12 NOS. ; 250mmLONG
Not Applicable






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM2 (A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] CW [] OTHER
MAX. NORMAL MINIMUM
(PumpDesign) (VWO)(40%MCR)
1800 1556 582
17 13.3 5.9
157 154.1 126
45Kg/cm
2
(g):160
o
C
0.5Kg/cm
2
atmax.flow
Bidder to specify













BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 9 OF 43

9


Tag No. : LCA92 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
457 x 12.7
SA 106 GR C
Bidder to specify
15 D
10 D : 5 D
[] HORIZONTAL [] VERTICAL UP

[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

NAME
SIGNATURE
DATE
PREPARED BY CHECKED BY APPROVED BY
COMPANY SEAL


NAME
SIGNATURE
DATE
SSV

13/06/2013

IJ S

13/06/2013

IJ S

13/06/2013


NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED AT 1800 T/HR & 582 T/HR FLOW VALUES.
2. RECOMMENDED RANGE IS 0 2000 T/HR.
3. 3 NOS. OF S-BAND SHALL BE REQUIRED

















BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 10 OF 43

10

Tag No. : LCR80 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRVUNL-2x660 MW SURATGARH STPP, STAGE-V
Bidder to specify
ONE (1) PER UNIT
DM MAKE-UP TO HOTWELL
Bidder to specify






ELEMENT

TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE


[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE [] BEVEL EDGE [] CARRIER
RING
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA
[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300 : A182 F 304
[] YES [] NO
Not Applicable
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE [] ON PIPE [] ON CARRIER
RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800
15NB/SS/SCH.40/6 NOS. ; 250mmLONG
Not Applicable






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM2 (A)) #
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] CW [] OTHER (DM WATER)
MAX. NORMAL MINIMUM
(3%MU) (1%MU)(0.5%MU)
31.5 21 10.5
4.0 6.8 7.2
33 33 33
10Kg/cm
2
(g):50
o
C
0.3Kg/cm
2
atmax.flow
Bidder to specify














BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 11 OF 43

11

Tag No. : LCR80 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
114.3 x 3.05
SA 312 TP 304 (ERW)
Bidder to specify
15 D
10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

NAME
SIGNATURE
DATE
PREPARED BY CHECKED BY APPROVED BY
COMPANY SEAL


NAME
SIGNATURE
DATE
SSV

13/06/2013

IJ S

13/06/2013

IJ S

13/06/2013


NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED AT 32 T/HR & 10 T/HR FLOW VALUES.
2. RECOMMENDED RANGE IS 0 50 T/HR.










BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 28 OF 43

28

Tag No.: 00LCP01 BP 001, 00LCP02 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRVUNL-2x660 MW SURATGARH STPP, STAGE-V
Bidder to specify
ONE (1) PER UNIT
DM WATER TO CST-1 & 2 INLET
Bidder to specify







ELEMENT
MAKE : MODEL
TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE


[] ORIFICE [] NOZZLE
[] ASME PTC 195 [] BS 1042 [] OTHER
[] SQ EDGE [] BEVEL EDGE [] CARRIER
RING
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA
[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300 : A182 F 304
[] YES [] NO
Not Applicable
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800
15NB/SS/SCH.40/6 NOS. ; 250mmLONG
Not Applicable







PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM2 (A)) #
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] CW [] OTHER (DM WATER)

MAX. NORMAL MINIMUM

68 31.5 21
2.0 4.0 6.0
33 33 33
10Kg/cm
2
(g):50
o
C
0.3Kg/cm
2
atmax.flow
Bidder to specify













BHEL
PEM
DATA SHEET FOR FLOW ELEMENTS
SPECIFICATION NO.: PE-TS-392-145-I105
VOLUME III
SECTION
REV. NO. 06 DATE : 27.02.14
SHEET 29 OF 43

29


Tag No.: 00LCP01 BP 001, 00LCP02 BP 001 Date Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
114.3 x 3.05
SA 312 TP 304 (ERW)
Bidder to specify
15 D

10 D: 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

NAME
SIGNATURE
DATE
PREPARED BY CHECKED BY APPROVED BY
COMPANY SEAL


NAME
SIGNATURE
DATE
SSV

13/06/2013

IJ S

13/06/2013

IJ S

13/06/2013


NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED AT 68 T/HR & 21 T/HR FLOW VALUES.
2. RECOMMENDED RANGE IS 0 80 T/HR.





DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 30 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : PCB10 BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRUVNL - 2X660MW SURATGARH STPP,STAGE-V
Bidder to specify
01 PER UNIT (2 FOR STATION)
SCS DISCHARGE HEADER
Bidder to specify






ELEMENT

TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE


[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE ,CONCENTRIC TYPE
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA

[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO













END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING: TYPE
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300# : ASTM A106
[] YES [] NO
NOT APPLICABLE
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800 : GLOBE
15NB/ SS316/SCH.80/6 NOS. ; 250mmLONG
NOT APPLICABLE






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM
2
(A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] ACW [] OTHER

MAX. NORMAL MINIMUM

3603 2771 835
7.5 4.2 3.2
60 36 36
7.5 Kg/cm
2
(g) : 60
o
C
0.15 Kg/cm
2

Bidder to specify
















DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 31 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0



Tag No. : PCB10 BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
711 x 10
Carbon Steel IS 2062
Bidder to specify


10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED



NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED BETWEEN 835 T/HR TO 3602 T/HR.
2. RECOMMENDED RANGE IS 0 3602 T/HR.




DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 32 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : PGC10BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRUVNL-2X660MW SURATGARH STPP,STAGE-V
Bidder to specify
ONE (1) PER UNIT (2 FOR STATION)
DMCW (TG) PUMP DISCHARGE HEADER
Bidder to specify







ELEMENT
MAKE : MODEL
TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE

Bidder to specify
[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE ,CONCENTRIC TYPE
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA

[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING: TYPE
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300# : ASTM A106
[] YES [] NO
NOT APPLICABLE
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800 : GLOBE
15NB/ SS316/SCH.80/6 NOS. ; 250mmLONG
NOT APPLICABLE






PROCESS
DATA
FLUID





FLOW (T/HR)
PRESSURE (KG/CM
2
(A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] DMCW [] OTHER

MAX. NORMAL MINIMUM


2440 1875 565
10 6.3 5.2
60 45.9 45.9
10 Kg/cm
2
(g) : 60
o
C
0.15 Kg/cm
2

Bidder to specify
















DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 33 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : PGC10BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
610 x 8.0
Carbon Steel IS 2062
Bidder to specify


10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED


NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED BETWEEN 565 T/HR TO 2440 T/HR.
2. RECOMMENDED RANGE IS 0 2440 T/HR.




DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 34 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : PGC40BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRUVNL - 2X660 MW SURATGARH
Bidder to specify
ONE (1) PER UNIT (2 FOR STATION)
DMCW (SG) PUMP DISCHARGE HEADER
Bidder to specify







ELEMENT
MAKE : MODEL
TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE

Bidder to specify
[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE,CONCENTRIC TYPE
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA

[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING: TYPE
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI-300# : ASTM A106
[] YES [] NO
NOT APPLICABLE
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800 : GLOBE
15NB/ SS316/SCH.80/6 NOS. ; 250mmLONG
NOT APPLICABLE






PROCESS
DATA
FLUID





FLOW (T/HR)
PRESSURE (KG/CM
2
(A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] DMCW [] OTHER

MAX. NORMAL MINIMUM


910 696 210
12 8.5 7.5
60 46.1 46.1
12 Kg/cm
2
(g) : 60
o
C
0.15 Kg/cm
2

Bidder to specify















DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 35 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : PGC40BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
355.6 x 7.1
Carbon Steel IS 2062
Bidder to specify


10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN





OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

TO BE REFLECTED IN VENDOR DOCUMENT




NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED BETWEEN 210 T/HR TO 910 T/HR.
2. RECOMMENDED RANGE IS 0 910 T/HR.




DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 36 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : GHD10BP001 Data Sheet No. PES-145-05-DS1-0
DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRUVNL - 2X660 MW SURATGARH
Bidder to specify
ONE (1) FOR STATION
RAW WATER PUMP DISCHARGE HEADER
Bidder to specify







ELEMENT
MAKE : MODEL
TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE

Bidder to specify
[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE ,CONCENTRIC TYPE
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA

[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING: TYPE
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300 # : ASTM A106
[] YES [] NO
NOT APPLICABLE
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800 : GLOBE
15NB/SS316/SCH.80/6 NOS. ; 250mmLONG
NOT APPLICABLE






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM
2
(A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] DMCW [] OTHER (Raw Water)

MAX. NORMAL MINIMUM

4825 3710 1115
10 2.2 1.5
60 38 38
10 Kg/cm
2
(g) : 60
o
C
0.15 Kg/cm
2

Bidder to specify
















DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 37 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : GHD10BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
813 X 10
Carbon Steel IS 2062
Bidder to specify


10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN






OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

TO BE REFLECTED IN THE VENDOR
DOCUMENT




NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED BETWEEN 1115 T/HR TO 4825 T/HR.
2. RECOMMENDED RANGE IS 0 4825 T/HR.



























DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 38 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : GHD15BP001 Data Sheet No. PES-145-05-DS1-0
DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRUVNL - 2X660 MW SURATGARH
Bidder to specify
ONE (1) FOR STATION
ASH WATER PUMP DISCHARGE HEADER
Bidder to specify







ELEMENT
MAKE : MODEL
TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE

Bidder to specify
[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE ,CONCENTRIC TYPE
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA

[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING: TYPE
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300 # : ASTM A106
[] YES [] NO
NOT APPLICABLE
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800 : GLOBE
15NB/SS316/SCH.80/6 NOS. ; 250mmLONG
NOT APPLICABLE






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM
2
(A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] DMCW [] OTHER (Raw Water)

MAX. NORMAL MINIMUM

875 670 205
10 2.2 1.5
60 38 38
10 Kg/cm
2
(g) : 60
o
C
0.15 Kg/cm
2

Bidder to specify
















DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 39 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : GHD15BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
355.6 X 7.1
Carbon Steel IS 2062
Bidder to specify


10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN






OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

TO BE REFLECTED IN THE VENDOR
DOCUMENT




NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED BETWEEN 205 T/HR TO 875 T/HR.
2. RECOMMENDED RANGE IS 0 875 T/HR.



























DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 40 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : GHD62BP001 Data Sheet No. PES-145-05-DS1-0
DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP
BY BIDDER)
GENERAL*
PROJ ECT
OFFER REFERENCE
QUANTITY
SERVICE
MAKE : MODEL

RRUVNL - 2X660 MW SURATGARH
Bidder to specify
ONE (1) FOR STATION
CW M/UP PUMP DISCHARGE HEADER
Bidder to specify







ELEMENT
MAKE : MODEL
TYPE
STANDARD
DESIGN



MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE

Bidder to specify
[] ORIFICE [] NOZZLE
[] ASME PTC 19.5 [] BS 1042 [] OTHER
[] SQ EDGE ,CONCENTRIC TYPE
[] SHORT RADIUS [] LONG RADIUS
[] LOW BETA [] HIGH BETA

[] SS316 [] OTHER
0.5 TO 0.7
Bidder to specify
[] YES [] NO
[] YES [] NO














END
CONNECTION
TYPE
FLANGE TYPE
FLANGE RATING : MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION


NUMBER OF TAPPINGS
ROOT VALVE NUMBER : SIZE
ROOT VALVE MATERIAL : RATING: TYPE
NIPPLE : SIZE/MATL/RATING/QTY
EXPANDER : SIZE/MATL/QTY
[] FLANGED [] BUTT WELD END
[] WELD NECK [] SLIP ON [] THREADED
ANSI 300 # : ASTM A106
[] YES [] NO
NOT APPLICABLE
[] D&D/2 [] CORNER [] VENTA CONTRACTA
[] ON FLANGE
[] ON PIPE [] ON CARRIER RING
[] 3 PAIR [] 2 PAIR [] OTHER
[] 12 [] 8 [] 6 [] 4 : [] 15 NB [] 25 NB
[] CS [] AS [] SS : [] ANSI #800 : GLOBE
15NB/SS316/SCH.80/6 NOS. ; 250mmLONG
NOT APPLICABLE






PROCESS
DATA
FLUID




FLOW (T/HR)
PRESSURE (KG/CM
2
(A))
TEMPERATURE (DEG. C.)
DESIGN PRESS : TEMP
MAX. ALLOWABLE PRESS LOSS
DIFF. PRESS AT MAX FLOW
[] CONDENSATE [] FEED WATER
[] STEAM [] CW [] OTHER

MAX. NORMAL MINIMUM

4160 3200 960
10 1.5 1.0
60 38 38
10 Kg/cm
2
(g) : 60
o
C
0.15 Kg/cm
2

Bidder to specify
















DATA SHEET FOR FLOW ELEMENTS (ORIFICE)
FOR 2 X 660 MW SURATGARH STPS
SPECIFICATION NO.: PE-TS-392-145-I005A
VOLUME
SECTION
REV. NO. 06 DATE 27.02.14
SHEET 41 of 43




F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


Tag No. : GHD62BP001 Data Sheet No. PES-145-05-DS1-0

DATA SHEET A & B

DATA SHEET A
(TO BE FILLED UP BY PURCHASER)
DATA SHEET B
(TO BE FILLED UP BY
BIDDER)
PIPE LINE
DATA
PIPE SIZE (OD x THK) mm
PIPE MATERIAL
BORE DIAMETER mm
MIN. AVAILABLE STRAIGHT
LENGTH
UPSTREAM : DOWNSTREAM
FLOW DIRECTION
711 X 10
Carbon Steel IS 2062
Bidder to specify


10 D : 5 D
[] HORIZONTAL [] VERTICAL UP
[] VERTICAL DOWN






OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES
[] REQUIRED [] NOT REQUIRED

TO BE REFLECTED IN THE VENDOR
DOCUMENT




NOTES:
1. FLOW ELEMENT ACCURACY IS REQUIRED BETWEEN 960 T/HR TO 4160 T/HR.
2. RECOMMENDED RANGE IS 0 4160 T/HR.

























Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION D
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SECTION D



DATA SHEETS - C






DATA SHEET FOR
FLOW MEASURING DEVICES
(ORIFICE)
SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER.


SPECIFICATION NO.: PE-TS-392-145-I 005A

VOLUME III
SECTION
REV. NO. 00 DATE: 05.04.2014
SHEET 1 OF 2
TAG No. . Qty................. Data Sheet No.: PES-145-05-DS2-0
Data Sheet C

DATA SHEET-C FOR FLOW MEASURING DEVICES (ORIFICE & NOZZLES)
(TO BE FILLED BY CONTRACTOR AFTER AWARD OF CONTRACT)


F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


GENERAL PROJ ECT
OFFER REFERENCE
TAG NO.: QUANTITY
SERVICE
MAKE MODEL


ELEMENT TYPE
STANDARD
DESIGN

MATERIAL
BETA RATIO
BORE DIAMETER
VENT HOLE
DRAIN HOLE
END TYPE
CONNECTION FLANGE TYPE
FLANGE RATING
MATERIAL
BRANCH PIPE
BRANCH PIPE MATERIAL
TAPPING LOCATION
NO. OF TAPPINGS
ROOT VALVE
NUMBER SIZE

ROOT VALVE MATERIAL
RATING
PROCESS DATA FLUID
FLOW T/HR
PRESS ATA
TEMP (DEG. C)
DESIGN PRESS TEMP

PRESS LOSS at MAX/ NORMAL FLOW
DIFF PRESS AT MAX/NORMAL FLOW
PIPE LINE DATA PIPE SIZE (OD X THK) mm
PIPE MATERIAL
DATA SHEET FOR
FLOW MEASURING DEVICES
(ORIFICE)
SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER.


SPECIFICATION NO.: PE-TS-392-145-I 005A

VOLUME III
SECTION
REV. NO. 00 DATE: 05.04.2014
SHEET 2 OF 2
TAG No. . Qty................. Data Sheet No.: PES-145-05-DS2-0
Data Sheet C

DATA SHEET-C FOR FLOW MEASURING DEVICES (ORIFICE & NOZZLES)
(TO BE FILLED BY CONTRACTOR AFTER AWARD OF CONTRACT)


F
O
R
M

N
O
.

P
E
M
-
6
6
6
6
-
0


BORE DIAMETER mm
AVAILABLE STRAIGHT LENGTH
UPSTREAM DOWNSTREAM

FLOW DIRECTION
OTHER
INFORMATION
IBR CERTIFICATION

TOTAL WEIGHT OF FLOW ELEMENT
AND ACCESSORIES

NAME NAME
SIGNATURE SIGNATURE
DATE DATE

Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION D
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
FLOW ELEMENT ASSEMBLY
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SECTION D



QUALITY PLAN








PEM :: C&I
QUALITY PLAN
FOR
FLOW ORIFICE PLATE ASSEMBLY
QUALITY PLAN NO.: PE-QP-392-145-I024
VOLUME IIB
SECTION D
REV. NO. 00 DATE: 24.06.13
SHEET 1 OF 2
Sl.
No.
Component /
operation
Characteristics Checked
*
Cate
gory
Type/Method
of
Check
Extent
of
Check
Reference
documents
Acceptance
Norms
Format
of
Records
Agency
$

Remarks
P W V
LEGEND: * CR - Critical characteristics IR - Inspection Reports DS Data Sheet MR- Manufacturer records
$
P - Agency Performing the Test. 1 - BHEL
MA - Major characteristics TC - Test Certificates SP Tech. Spec. MS- Manufacturer standards W - Agency Witnessing the Test. 2 - Vendor
MI - Minor characteristics AP Approved Drawings/doc V - Agency Verifying the Test. 3 - Sub-vendor
1.0 MATERIAL

1.1 Orifice Plate 1. Physical, Chemical
properties
MA Physical,
Chemical
Tests
One /
Plate
OR
One/
Heat
AP / DS / SP

AP / DS / SP

Lab Report 3/2 --- 2,1 IBR
certification
(if
applicable)
to be
verified by
BHEL
2. Dimensions MA Measurement 100% AP AP IR 3/2 1

1.2
Flanges
A. Forgings
Chemical,Mech Properties,
UT & Heat Treatment
MA
Chem & Mech
UT test
Sample
Material Spec
as per ASTM
A 388 for UT
ANSI B 16.34
MTC,UT
cert,HT cert
3/2 --- 1
B. Machining
Dimensions MA
Measurement

100 % AP / DS AP / DS IR 3/2 ---- 1

2.0 IN PROCESS
Machine 1. Dimension

2. Surface finish

MA

MA
Measurement

Visual
100%

100%
AP

------------
AP

Mirror Finish
IR

-------
3/2

3/2
2

2
2

---



3. Surface flaw on
machined surface
MA Penetrant test 100% ASTM 165 /
IS:3658
No surface flaw IR / TC 3/2 2 1

3.0

ASSEMBLY and
FINAL INSPECTION
1. Overall dimensions


2. Marking, Tag no.
Direction of flow

3. Calibration


4 Painting
MA


MA


MA


MA
Measurement


Visual


Performance
Test

Visual
100%


100%


One per
type

100%
AP


AP / DS


------------


SP / MS
AP


AP / DS


SP


SP / MS
IR


IR


TC


IR / MR
3/2


3/2


3/2


3/2
2,1


2





-----
----


1


1


1













6 7


PEM :: C&I
QUALITY PLAN
FOR
FLOW ORIFICE PLATE ASSEMBLY
QUALITY PLAN NO.: PE-QP-392-145-I024
VOLUME IIB
SECTION D
REV. NO. 00 DATE: 24.06.13
SHEET 2 OF 2
Sl.
No.
Component /
operation
Characteristics Checked
*
Cate
gory
Type/Method
of
Check
Extent
of
Check
Reference
documents
Acceptance
Norms
Format
of
Records
Agency
$

Remarks
P W V
LEGEND: * CR - Critical characteristics IR - Inspection Reports DS Data Sheet MR- Manufacturer records
$
P - Agency Performing the Test. 1 - BHEL
MA - Major characteristics TC - Test Certificates SP Tech. Spec. MS- Manufacturer standards W - Agency Witnessing the Test. 2 - Vendor
MI - Minor characteristics AP Approved Drawings/doc V - Agency Verifying the Test. 3 - Sub-vendor
4.0 PACKING
Soundness of Packing
against transit damage
MA
Visual

100% SP / MS SP / MS ---- 3/2 ---- ----
Refer Note
4


NOTE:

1. All test reports & dimension reports shall be verified by BHEL wherever verification is by BHEL at the time of Final Inspection.
2. Minimum 2 coats of primer paint to be applied before dispatch.
3. CALIBRATION Test to be carried out at IIT-DELHI / FCRI or BHEL approved laboratory.
4. Sea Worthy packing, if applicable.

7 7
Form No. PEM-6666-0
SPECIFICATION NO. PE-TS-392-145-I 005A


VOLUME II-B

SECTION D
REV. NO. 00 DATE: 07.04.2014


SHEET








Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SECTION D



BILL OF QUANTITY
INCLUDING
SPARES






SPECIFICATION NO. PE-TS-392-145-I 005A

VOLUME II-B
SECTION D

REV. NO. 00 DATE: 07.04.2014


SHEET 1 of 1





Technical specification for
FLOW ELEMENT ASSEMBLIES
(Orifice)


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER
BILL OF QUANTITY



[B] START-UP / COMMISSIONING SPARES FOR FLOW ELEMENT ASSEMBLIES

S.No DESCRIPTION TOTAL QTY
1 PAIR OF GASKETS FOR FLOW ORIFICES
ONE (1) PAIR FOR EACH
TAG FOR EACH UNIT


[C] MANDATORY SPARES FOR FLOW ELEMENT ORIFICE PLATE




[A] FLOW ELEMENT ASSEMBLIES COMPLETE WITH Three (3) pairs of tappings, AND
ACCESSORIES, like Pressure take-off points, Root valves, Nipples etc.
S.
No.
TAG NO. SERVICE
TYPE OF
ASSY
QTY
PER
UNIT
QTY
For 2
units
i)
LCA01BP001,
LCA02BP001,
LCA03BP001
CEP A/B/C DISCHARGE FLOW ORIFICE 03

06
ii) LCA20BP001 CONDENSATE FLOW D/S OF GSC ORIFICE 01 02
iii) LCR80BP001 DM M/UP TO HOTWELL ORIFICE 01 02
iv) LCP01BP001 DM WATER TO CST INLET ORIFICE 01 02
v) PCB10BP011 SCS DISCHARGE HEADER ORIFICE 01 02
vi) PGC10BP100 DMCW (TG) PUMP DISCHARGE HEADER ORIFICE 01 02
vii) PGC40BP100 DMCW (SG) PUMP DISCHARGE HEADER ORIFICE 01 02
viii) 00GHD10BP011
RAW WATER PUMP DISCHARGE HEADER
(Common for 2 units)
ORIFICE 01 01
ix) 00GHD15BP011
ASH WATER PUMP DISCHARGE HEADER
(Common for 2 units)
ORIFICE 01 01
x) 00GHD62BP011
CW M/UP PUMP DISCHARGE HEADER
(Common for 2 units)
ORIFICE 01 01
xi) LCA92BP001 CONDENSATE FLOW TO DEAERATOR ORIFICE 01 02
S.
No.
SERVICE
TYPE OF
ASSY
TOTAL QTY
(IN NOS.)
i) CEP A/B/C DISCHARGE FLOW ORIFICE 02
ii) CONDENSATE FLOW D/S OF GSC ORIFICE 02
iii) DM M/UP TO HOTWELL ORIFICE 02
iv) DM WATER TO CST INLET ORIFICE 02
v) SCS DISCHARGE HEADER ORIFICE 02
vi) CW M/UP PUMP DISCHARGE HEADER ORIFICE 02
vii) DMCW (TG) PUMP DISCHARGE HEADER ORIFICE 02
viii) DMCW (SG) PUMP DISCHARGE HEADER ORIFICE 02
ix) RAW WATER PUMP DISCHARGE HEADER ORIFICE 02
x) ASH WATER PUMP DISCHARGE HEADER ORIFICE 02
xi) CONDENSATE FLOW TO DEAERATOR ORIFICE 02
Form No. PEM-6666-0
SPECIFICATION NO.PE-TS-392-145-I 005A

VOLUME III
SECTION
REV. NO. 00 DATE: 07.04.2014


SHEET 1 OF 1




BHEL - PS-PEM



Technical specification for
FLOW ELEMENT ASSEMBLIES


SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

SCHEDULE OF SUBMISSION OF DRAWINGS / DOCUMENTS, EQUIPMENT MANUFACTURE
INSPECTION AND DESPATCH


1. ZERO DATE DATE of LOI / FOI / TOI
2. Submission of Data Sheets / documents /
catalogues / Valve sizing calculations / Noise
calculations for approval.
2 Weeks from the Zero date.
3. Technical finalisation, freezing of inputs of
manufacture by way of vetting of documents and
technical discussions and resubmissions of
documents (if required)
6 Weeks from the Zero date.
4. Inspection of Equipment as per Approved
(Category-I) drawings / documents.
14 Weeks from the Zero date.
5. Release of MDCC by BHEL 15 Weeks from the Zero date.
6. Dispatch (Packaging & Dispatch) 16 Weeks from the Zero date.
7. Final documents submission as per Contract 16 Weeks from the Zero date.


NOTE: Delays due to non-fulfillment of the requirements of approved Quality Plan and approved
Data sheets, Drawings, Catalogues and Sizing Calculations observed during inspection
shall be to the Vendors account.


Delays due to INCOMPLETE (Partly) submission of Data sheets, Drawings, Catalogues
and Sizing Calculations also be considered as DOCUMENTS NOT SUBMITTED





(Signature and Stamp of the Bidder)





SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER






TECHNICAL SPECIFICATION
FOR
FLOW ELEMENT ASSEMBLIES
(ORIFICE)



VOLUME III


SPECIFICATION Nos
PE-TS-392-145-I 005A







BHARAT HEAVY ELECTRICALS LIMITED
POWER SECTOR
PROJ ECT ENGINEERING MANAGEMENT DIVISION
NOIDA, INDIA
SPECIFICATION NO. PE-TS-392-145-I 005A

VOLUME III

SECTION

REV. NO. 00 DATE: 07.04.2014


SHEET





Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER




CONTENTS

VOL-III


S. No.
DESCRIPTION
No. of
sheets
1 COMPLAINCE CERTIFICATES 1
2 SCHEDULE OF PRICES 1
3 SCHEDULE OF UNIT PRICES 1
4 INSPECTION SCHEDULE 1
5 CALIBERATION CHARGES 1

COMPLIANCE CERTIFICATE
For
Flow Elements assemblies
(To be Signed & Stamped by the Bidder)

Project: SURATGARH, STAGE-V, UNIT # 7 & 8 (2 x 660 MW) THERMAL POWER
Specification no. : PE-TS-392-145-I 005A

We shall comply with the following:-

1. All the requirements as stated in Technical Specification / Specific Technical
requirement / Data sheets / BHEL quality plan etc as enclosed in the tender, shall
be fully complied without any deviation.

2. BHEL Quality Plan (enclosed with the specification) duly signed and stamped is
submitted herewith without any deviation.

3. Sizing Calculations, Data sheet-C in line with Data sheet-A of specification,
dimensional drawings / edge preparation details, etc shall be submitted for
BHEL/Customer review and approval, to reach BHEL within 15 days after receipt
of LOI.

4. Any change in Sizing calculations, QP etc., if desired by BHEL / Customer during
approval of the documents after award of contract, without major changes in
process parameters as per tender Specification, shall be carried out without any
commercial implication and time delay.

5. The offered Flanges, Root valves, Nipples, Reducers are suitable for the
applicable process parameters.


Signature with date
Name
Company seal




SPECIFICATION NO. PE-TS-392-145-I 005A
VOLUME III

SECTION

REV. NO. 00 DATE: 07.04.2014


SHEET 1 of 1





Technical specification for
FLOW ELEMENT ASSEMBLIES
(Orifice)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER



CALIBRATION CHARGES FOR FLOW ELEMENTS



NOTE: 1. Bidder to note that CALIBRATION TEST is required to be conducted on one type per size,
Bidder to group such assemblies and indicate the same along with the price bid.

[A] FLOW ELEMENT ASSEMBLIES COMPLETE WITH Three (3) pairs of tappings, AND
ACCESSORIES, like Pressure take-off points, Root valves, Nipples etc.
S.
No.
TAG NO. SERVICE
TYPE OF
ASSY
CALIBRATION
CHARGES PER
ASSY(EX WORKS)
REMARKS
i)
LCA01BP001,
LCA02BP001,
LCA03BP001
CEP A/B/C DISCHARGE FLOW ORIFICE
ii) LCA20BP001 CONDENSATE FLOW D/S OF GSC ORIFICE
iii) LCR80BP001 DM M/UP TO HOTWELL ORIFICE
iv) LCR70BP001 DM WATER TO CST INLET ORIFICE
v) PCB10BP011 SCS DISCHARGE HEADER ORIFICE
vi) 00GHD62BP001
CW M/UP PUMP DISCHARGE
HEADER
ORIFICE
vii) PGC10BP100
DMCW (TG) PUMP DISCHARGE
HEADER
ORIFICE
viii) PGC40BP100
DMCW (SG) PUMP DISCHARGE
HEADER
ORIFICE
ix) 00GHD10BP011
RAW WATER PUMP DISCHARGE
HEADER
ORIFICE
x) 00GHD15BP011
ASH WATER PUMP DISCHARGE
HEADER
ORIFICE
xi) LCA92BP001
CONDENSATE FLOW TO
DEAERATOR
ORIFICE
SPECIFICATION NO. PE-TS-392-145-I 005A

VOLUME III

SECTION

REV. NO. 00 DATE: 07.04.2014


SHEET





Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER

INSPECTION SCHEDULE

(PLACE & ADDRESS OF TESTING/ INSPECTION AND ITS SCHEDULE DATE & DURATION IN NUMBER
OF DAYS ITEM/COMPONENTWISE TO BE LISTED)








































PARTICULARS OF THE BIDDER / AUTHORISED REPRESENTATIVE


NAME DESIGNATION SIGNATURE DATE COMPANY SEAL
SPECIFICATION NO. PE-TS-392-145-I 005A

VOLUME III

SECTION

REV. NO. 00 DATE: 07.04.2014


SHEET





Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER



SCHEDULE OF PRICES FOR FLOW ELEMENT (ORIFICE)
[A] FLOW ELEMENT ASSEMBLIES COMPLETE WITH Three (3) pairs of tappings, AND
ACCESSORIES, like Pressure take-off points, Root valves, Nipples etc.

S.
No.
TAG NO. SERVICE

TYPE
Unit Price
for each
ASSY. (Rs)
(Ex-works)
Total price of
flow assemblies
(Rs.)
(PER UNIT)
(Ex-works)
i) LCA01BP001 CEP A DISCHARGE FLOW
ORIFICE

ii) LCA02BP001 CEP B DISCHARGE FLOW
ORIFICE

iii) LCA03BP001 CEP C DISCHARGE FLOW
ORIFICE

iv) LCA20BP001
CONDENSATE FLOW D/S OF
GSC
ORIFICE

v) LCR80BP001 DM M/UP TO HOTWELL
ORIFICE

vi) LCP01BP001 DM WATER TO CST INLET-1
ORIFICE

vii) PCB10BP011 SCS DISCHARGE HEADER
ORIFICE

viii)
PGC10BP100
DMCW (TG) PUMP DISCHARGE
HEADER
ORIFICE

ix)
PGC40BP100
DMCW (SG) PUMP DISCHARGE
HEADER
ORIFICE

x)
00GHD10BP011
RAW WATER PUMP
DISCHARGE HEADER
(COMMON FOR 2 UNITS)
ORIFICE

xi)
00GHD15BP011
ASH WATER PUMP DISCHARGE
HEADER (COMMON FOR 2
UNITS)
ORIFICE

xii)
00GHD62BP001
CW M/UP PUMP DISCHARGE
HEADER (COMMON FOR 2
UNITS)
ORIFICE

xiii)
LCA92BP001
CONDENSATE FLOW TO
DEAERATOR
ORIFICE



[B] START-UP / COMMISSIONING SPARES FOR FLOW ELEMENT ASSEMBLIES

S.
No.
DESCRIPTION TOTAL QUANTITY
i) PAIR OF GASKETS FOR FLOW ORIFICES ONE (1) PAIR FOR EACH TAG FOR EACH UNIT

[C] CALIBERATION CHARGES (SEPARATE LIST TO BE ATTACHED)


[D] MANDATORY SPARE (SEPARATE LIST TO BE ATTACHED)


[E] DOCUMENTATION CHARGES

PARTICULARS OF THE BIDDER / AUTHORISED REPRESENTATIVE

NAME DESIGNATION SIGNATURE DATE COMPANY SEAL

SPECIFICATION NO. PE-TS-392-145-I 005A

VOLUME III

SECTION

REV. NO. 00 DATE: 07.04.2014


SHEET





Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER


SCHEDULE OF UNIT PRICES

[A] Unit prices for Gaskets


[B] MANDATORY SPARES FOR FLOW ELEMENT: ORIFICE PLATE

SNO SERVICE (A)
TYPE
(B)
Unit
price (Ex
Works)
Qty
(Nos.)
Total Price (Ex-
works)
1 CEP DISCHARGE FLOW ORIFICE
2

2 CONDENSATE FLOW D/S OF GSC ORIFICE 2
3
DM M/UP TO HOTWELL
ORIFICE
2

4 DM WATER TO CST INLET ORIFICE
2

5 SCS DISCHARGE HEADER ORIFICE 2
6 CW M/UP PUMP DISCHARGE HEADER ORIFICE 2
7 DMCW (TG) PUMP DISCHARGE HEADER ORIFICE 2
8 DMCW (SG) PUMP DISCHARGE HEADER ORIFICE
2

9 RAW WATER PUMP DISCHARGE HEADER ORIFICE
2

10 ASH WATER PUMP DISCHARGE HEADER ORIFICE 2
11 CONDENSATE FLOW TO DEAERATOR ORIFICE 2

[C] UNIT PRICES FOR ROOT VALVES AND NIPPLES








S.No DESCRIPTION For Orifice Tag Nos
Unit Rate (Rs)
(ExWorks)
1 PAIR OF GASKETS
LCA01BP001
LCA02BP001
LCA03BP001
LCA20BP001
LCR80BP001
LCP01BP001
PCB10BP011
PGC10BP100
PGC40BP100
00GHD10BP011
00GHD15BP011
00GHD62BP001
LCA92BP001
S.No DESCRIPTION Tag Nos
Unit Rate (Rs)
(ExWorks)
1 ROOT VALVES SS, 15 NB, SW, #800
2 NIPPLE 15 NB/SS/SCH 40/12 Nos. 250 mm long
58
SPECIFICATION NO. PE-TS-392-145-I 005A

VOLUME III

SECTION

REV. NO. 00 DATE: 07.04.2014


SHEET





Technical specification for
FLOW ELEMENT ASSEMBLIES
(ORIFICE)

SURATGARH, STAGE-V, UNIT # 7 & 8
(2 x 660 MW) THERMAL POWER


[D] DOCUMENTATION CHARGES



PARTICULARS OF THE BIDDER / AUTHORISED REPRESENTATIVE

NAME DESIGNATION SIGNATURE DATE COMPANY SEAL