Scribd
Upload
86 views

Nissan Sentra 2.0

This document provides a parts list and installation instructions for a trailer hitch on a Nissan Sentra. The parts list includes 7 items like carriage bolts, spacers, and nuts. The hitch has a gross load capacity of 1000 lbs and tongue weight of 100 lbs. Installation takes approximately 25 minutes and requires drilling holes, fishwiring bolts, and removing the spare tire. Periodic inspections of fasteners and structural components are recommended.

Uploaded by

FORYOUMA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
86 views

Nissan Sentra 2.0

This document provides a parts list and installation instructions for a trailer hitch on a Nissan Sentra. The parts list includes 7 items like carriage bolts, spacers, and nuts. The hitch has a gross load capacity of 1000 lbs and tongue weight of 100 lbs. Installation takes approximately 25 minutes and requires drilling holes, fishwiring bolts, and removing the spare tire. Periodic inspections of fasteners and structural components are recommended.

Uploaded by

FORYOUMA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Parts List

DESCRIPTION PART NUMBER QTY ITEM


CARRIAGE BOLT 1/2-13 x 1 1/2 2 1
7/16 " FISHWIRE TOOL CM-438-FW 1 2
CARRIAGE BOLT 7/16-14 x 1 2 3
.250 x 1.00 x 2.00" SQUARE HOLE SPACER CM-SP7 2 4
HEX FLANGE NUT 7/16-14 2 5
HEX FLANGE NUT HFN 1213 2 6
.250" TRUNK PAN SPACER CM-11342-TPS 1 7
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HITCH WEIGHT: LBS.

INSTALL TIME: MINUTES

INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
1,000 100
25
60
11342 / 24727 NISSAN SENTRA 2.0
4/10/2008
1) Remove spare tire from trunk, remove rubber plugs as shown.

2) Install trunk pan spacer with (2) 1/2" carriage bolts.

3) Enlarge two holes in bumper beam which line up with outer two holes in hitch plate.

4) Fishwire (2) 7/16" carriage bolts with SP7 spacers from end of bumper beam to enlarged holes.

5) Raise hitch into position and finger tighten in place with (2) 1/2" and (2) 7/16" flange nuts.

6) Torque all 7/16" hardware to 50 ft.-lb. and all 1/2" hardware to 75 ft.-lb.

7) Return spare tire to trunk.
-DRILLING REQUIRED
-FISHWIRING REQUIRED
-SPARE TIRE REMOVAL REQUIRED
2
1
7
6
3
4
HOLE ENLARGEMENT
REQUIRED FOR INSTALL
TRUNK PAN
DESIGNED FOR USE WITH
BALL MOUNT # D-20 / 36061

You might also like