Scribd
Upload
685 views

Check Valve Data Sheet

This document provides specifications for a check valve with the following key details: - Valve tag number is A10A - Piping class is A, corrosion allowance is 1.50 mm, standard is BS:1868, rating is 150#, service is MS/HSD/SKO/WATER/BITUMIN - Size range is 4-14 inches, ends are flanged to B16.5 RF serr. Fin.; 125AARH - Construction material includes ASTM A 216 GR. WCB, ASTM A 193 GR. B 7, and ASTM A 194 GR. 2H steel - Testing shall be done according to BS:6755 (PART-1)

Uploaded by

Jèfrì Pìném
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
685 views

Check Valve Data Sheet

This document provides specifications for a check valve with the following key details: - Valve tag number is A10A - Piping class is A, corrosion allowance is 1.50 mm, standard is BS:1868, rating is 150#, service is MS/HSD/SKO/WATER/BITUMIN - Size range is 4-14 inches, ends are flanged to B16.5 RF serr. Fin.; 125AARH - Construction material includes ASTM A 216 GR. WCB, ASTM A 193 GR. B 7, and ASTM A 194 GR. 2H steel - Testing shall be done according to BS:6755 (PART-1)

Uploaded by

Jèfrì Pìném
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Valve Tag No. Piping Class: A10A Corrosion Allowance 1.

50 mm
Standard: BS:1868 Rating: 150 # Service
MS/HSD/SKO/
WATER/ BITUMIN
Size Range: 4 inch to 14 inch Ends: Flanged to B16.5 RF serr.Fin.; 125AARH
VALVE PORT REDUCED OPENING PORT MANUFACTURER'S OFFER
CONSTRUCTION CONSTRUCTION MATERIAL
CAST
COVER BOLTED
DISC
BODY SEAT RING RENEWABLE
DISC HINGE
HINGE PIN
COVER STUD BOLTS
COVER NUTS
BONNET GASKET
HYDROSTATIC TEST PRESSURE BODY:450 PSI SEAT:315 PSI
TEST PRESSURE WITH AIR
NOTES:1, 2, 3, 4 & 5 BELOW
1.This valve specification sheet shall be read in conjunction with Technical Specification for valves. 4. Seats shall be non-renewable integral type only.
5. Valves shall be suitable for Horizontal/vertical installation.
CS CHECK VALVE DATA SHEET
2.Bidder shall clearly write all/ any deviation against each part/ material of valve in the space provided .
ASTM A 216 GR. WCB + 13% CR STEEL FACING
ASTM A 216 GR. WCB + 13% CR STEEL FACING
ASTM A 216 GR. WCB
13% CR STEEL (NO CASTING)
3.Testing shall be as per BS:6755 (PART-1)
ASTM A 193 GR. B 7
ASTM A 194 GR. 2 HASTM A 194 GR. 2 H
SPIRAL WOUND SS316-CA FILLER
PART DESCRIPTION
BODY
MATERIAL
ASTM A 216 GR. WCB
ASTM A 216 GR. WCB
80 PSI

You might also like