Scribd
Upload
163 views

Rocking Horse Center Body (Cut To Solid Green Line Only) : " Hole

The document provides templates and instructions for cutting pieces needed to construct a rocking horse or pony. It includes patterns for the center body, outer body, rockers, legs, mane, tail and saddle. Dimensions and details are provided for holes, bevels, roundovers and grain direction for each piece. Templates are shown for tracing patterns onto wood blanks that will then be cut out and assembled into the toy animal.

Uploaded by

Isabel Vega
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
163 views

Rocking Horse Center Body (Cut To Solid Green Line Only) : " Hole

The document provides templates and instructions for cutting pieces needed to construct a rocking horse or pony. It includes patterns for the center body, outer body, rockers, legs, mane, tail and saddle. Dimensions and details are provided for holes, bevels, roundovers and grain direction for each piece. Templates are shown for tracing patterns onto wood blanks that will then be cut out and assembled into the toy animal.

Uploaded by

Isabel Vega
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

" hole

" hole
Align with centerline
of blank
Rocking horse center body
(cut to solid green line only)

A
l i g
n
w
i t
h
c
e
n
t
e
r
l i n
e

o
f b
l a
n
k
A
Center body
13"
24"
13 x 24" center body blank
" hole
" hole
Align with centerline
of blank
Rocking Pony outer body - 2 required
(cut to solid green line only)

A
l i g
n
w
i t
h
c
e
n
t
e
r
l i n
e

o
f b
l a
n
k
13
24"
13 x 24" outer body blank (2 required)
" hole

/" hole /" deep

" hole
for handle


B
Outer body
(2 required)
Extend this line onto edge
of body lamination B A
Extend this line onto edge
of body lamination B A
B
Join A and B as shown to make half pattern of rocker.
The other half is a mirror image.
H
I
J J
H
H
A
" hole
" counterbore " deep
(rear leg)


Rocker support
(2 required)
Rocker
(2 required)
" hole 1" deep


Rocker Support
End View


5 angle
top and bottom


" hole
" counterbore " deep
(rear leg)


C
e
n
t
e
r
l
i
n
e
1"


3
8"


10"


" hole
" counterbore " deep


" hole
" counterbore " deep



" hole
" counterbore " deep


2


5
8"


" round-overs along top edges and ends


Left rear leg
outside face
4 back bevel
cut from outside face
(see end view detail)
Left front leg
outside face
/" hole in
/" counterbore " deep

/" through hole in
/" counterbore

D
C
Flush end of pattern
with end of leg blank

Flush end of pattern
with end of leg blank

" round-over along
perimeter of outside face

Stop " round-over
on inner face
Stop " round-over
on inner face
" round-over along
perimeter of outside face

C
e
n
t
e
r
l
i
n
e
C
e
n
t
e
r
l
i
n
e
D
End View Detail
left rear leg,
looking toward head
(not to scale)
4 bevel
Right rear leg
outside face
4 back bevel
cut from outside face
(see end view detail)
Right front leg
outside face
/" hole in
/" counterbore " deep

/" through hole in
/" counterbore

D
C
Flush end of pattern
with end of leg blank

Flush end of pattern
with end of leg blank

" round-over along
perimeter of outside face

Stop " round-over
on inner face
Stop " round-over
on inner face
" round-over along
perimeter of outside face

C
e
n
t
e
r
l
i
n
e
C
e
n
t
e
r
l
i
n
e
D
End View Detail
right rear leg,
looking toward head
(not to scale)
4 bevel
Mane
Tail
Stop " round-over
Test ft before making mortise.
G
F
Stop " round-over
Stop " round-over
Stop " round-over
G
r
a
i
n

d
i
r
e
c
t
i
o
n
G
r
a
i
n

d
i
r
e
c
t
i
o
n
Saddle sides
(2 required)
Saddle seat (3 required)
" hole
" shank hole
L
M
Stirrup strap
No round-over
on this end


K
" round-over
along top perimeter


" round-over
along top perimeter


" round-over


End " round-over


End " round-over

You might also like