Scribd
Upload
50 views

18.1 Necessity: Module 5: Directional Overcurrent Protection Lecture 18: Directional Overcurrent Relaying

The document discusses the need for directional overcurrent protection in transmission and sub-transmission systems with multiple power sources. In such systems, non-directional overcurrent relays installed at both ends of a transmission line may operate incorrectly for faults on the line. For example, a relay at one end may operate unnecessarily for a fault located closer to the other end. This could result in loss of power to loads when the line is disconnected when it does not need to be. Directional overcurrent relays are necessary to distinguish the direction of fault current flow and ensure only the correct relays operate to isolate faults at either end of the line.

Uploaded by

Ravinder Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
50 views

18.1 Necessity: Module 5: Directional Overcurrent Protection Lecture 18: Directional Overcurrent Relaying

The document discusses the need for directional overcurrent protection in transmission and sub-transmission systems with multiple power sources. In such systems, non-directional overcurrent relays installed at both ends of a transmission line may operate incorrectly for faults on the line. For example, a relay at one end may operate unnecessarily for a fault located closer to the other end. This could result in loss of power to loads when the line is disconnected when it does not need to be. Directional overcurrent relays are necessary to distinguish the direction of fault current flow and ensure only the correct relays operate to isolate faults at either end of the line.

Uploaded by

Ravinder Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Module 5 : Directional Overcurrent Protection

Lecture 18 : Directional Overcurrent Relaying


18.1 Necessity

In the overcurrent protection scheme considered in previous lectures, we had implicitly assumed that,
1. System is radial.
2. There is a single source.


This is quite true for traditional distribution systems but it does not hold true for sub-transmission or transmission system
with multiple sources. Fig 18.1 shows a system which is radial but it has two sources connected to it. If relays for protection
are installed only at one end of transmission line say towards source A end, it is obvious that after opening of relay in red,
the fault will continue to be fed from source B. Hence, relays are also installed at other end of line to detect fault and
disconnect transmission line from the other end as well. Similar situation will exist even for a single source system if
parallel paths exist (fig 18.2). Hence, system which have multiple paths to source require relays at both ends. However,
installing relays at both ends does not provide a complete relaying solution. To understand the reason, consider the action
of red relay in fig 18.1 with respect to two likely faults F
1
and F
2
.



If the fault is at F
1
then it is
responsibility of red
relays to open. If fault
is at F
2
, then it is the
green relays which
should trip the line.
However, it is quite
likely that for fault F
2
,
the circled red relay
may trip before
circled green relay
opens to disconnect
feed from the source
B, the reason being
that both relays are
subjected to same
fault current.

In other words, circled red relay competes with circled green relay to clear fault. Opening of circled red relay unnecessarily
causes loss of service to load at bus P and it should be classified as wrong operation.

1 2 3 4 5 6 7 8 9
Page 1of 1 Text_Template
8/1/2009 http://www.cdeep.iitb.ac.in/nptel/Electrical%20Engineering/Power%20System%20Protection/Module-5/Lec-1...

You might also like