Scribd
Upload
61K views

National Building Code 2005

This document introduces the National Building Code of India 2005. It discusses how the code was first published in 1970 and revised in 1983 to modernize building regulations and make them more performance-based rather than specification-based. It describes how the code aims to unify building regulations across India. It also summarizes some of the key changes between the 1983 and 2005 versions, including additions related to architectural control, industrialized construction systems, and updates to structural design codes. The document emphasizes the importance of construction to India's development and the goal of the code to ensure optimal returns and avoid wastage on large national investments in building construction.

Uploaded by

api-26172168
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
61K views

National Building Code 2005

This document introduces the National Building Code of India 2005. It discusses how the code was first published in 1970 and revised in 1983 to modernize building regulations and make them more performance-based rather than specification-based. It describes how the code aims to unify building regulations across India. It also summarizes some of the key changes between the 1983 and 2005 versions, including additions related to architectural control, industrialized construction systems, and updates to structural design codes. The document emphasizes the importance of construction to India's development and the goal of the code to ensure optimal returns and avoid wastage on large national investments in building construction.

Uploaded by

api-26172168
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1161

.

I
.

I
NATIONAL BUILDING CODE
OF INDIA 2005

,,. . . ...

b. -.,
..

.—
-,
(J 6$
NATIONAL
BUILDING
CODE OF INDIA
2005

BUREAU OF INDIAN STANDARDS


--

SP 7:2005

FIRST PUBLISHED 1970


FIRST REVISION 1983
SECOND REVISION 2005

0 BUREAU OF INDIAN STANDARDS

ICS 0.120; 91.040.01


ISBN 81-7061 -026-5

PRICE Rs.7550.(J4

PUBLISHED BY BUREAU OF INDIAN STANDARDS, MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR


MARG, NEW DELHI 110002, PRINTED AT SUNSHINE PROCESS, C-105/5, NARAINA INDUSTRIAL
AREA, PHASE I, NEW DELHI 110028 (INDIA).

(iv)
FOREWORD

Construction prograrnmes are interwoven in a large measure in all sectors of development, be it housing, transport,
industry, irrigation, power, agriculture, education or health. Construction, both public and private, accounts for
about fifty percent of the total outlay in any Five Year Plan. Half of the total money spent on construction
activities is spent on buildings for residential, industrial, commercial, administrative, education, medical, municipal
and entertainment uses. It is estimated that about half of the total outlay on buildings would be on housing. It is
imperative that for such a large national investment, optimum returns are assured and wastage in construction is
avoided.

Soon after the Third Plan, the Planning Commission decided that the whole gamut of operations involved in
construction, such as, administrative, organizational, financial and technical aspects, be studied in depth. For this
study, a Panel of Experts was appointed in 1965 by the Planning Commission and its recommendations are found
in the ‘Report on Economies in Construction Costs’ published in 1968.

One of the facets of building construction, namely, controlling and regulating buildings through municipal byelaws
and departmental handbooks received the attention of the Panel and a study of these regulatory practices revealed
that some of the prevailing methods of construction were outmoded; some designs were overburdened with
safety factors and there were other design criteria which, in the light of newer techniques and methodologies,
could be rationalized; and building byelaws and regulations of municipal bodies which largely regulate the
building activity in the country wherever they exist, were outdated. They did not cater to the use of new building
materials and the latest developments in building designs and construction techniques. It also became clear that
these codes and byelaws lacked uniformity and they were more often than not ‘specification oriented’ and not
‘performance oriented’.

These studies resulted in a recommendation that a National Building Code be prepared to unify the building
regulations throughout the country for use by government departments, municipal bodies and other construction
agencies. The then Indian Standards Institution (now Bureau of Indian Standards) was entrusted by the Planning
Commission with the preparation of the National Building Code. For fulfilling this task a Guiding Committee for
the preparation of the Code was setup by the Civil Engineering Division Council of the Indian Standards Institution
in 1967. This Committee, in turn, set up 18 specialist panels to prepare the various parts of the Code. The
Guiding Committee and its panels were constituted with architects, planners, materials experts, structural,
construction, electrical illumination, air conditioning, acoustics and public health engineers and town planners.
These experts were drawn from the Central and State Governments, local bodies, professional institutions and
private agencies. The first version of the Code was published in 1970.

After the National Building Code of India was published in 1970, a vigorous implementation drive was launched
by the Indian Standards Institution to propagate the contents and use of the Code among all concerned in the field
of planning, designing and construction activities. For this, State-wise Implementation Conferences were organized
with the participation of the leading engineers, architects, town planners, administrators, building material
manufacturers, building and plumbing services installation agencies, contractors, etc.

These Conferences were useful in getting across the contents of the Code to the interests concerned. These
Conferences had also helped in the establishment of Action Committees to look into tie actual implementation
work carried out by the construction departments, local bodies and other agencies in different States. The main
actions taken by the Action Committees were to revise and modernize their existing regulato~ media, such as,
specifications, handbooks, manuals, etc, as well as building byelaws of local bodies like municipalities at city
and town levels, zilla parishads, panchayats and development authorities, so as to bring them in line with the
provisions contained in the National Building Code of India. In this process, the Indian Standards Institution
rendered considerable support in redrafting process.

Since the publication in 1970 version of the National Building Code of India, a large number of comments and
useful suggestions for modifications and additions to different parts and sections of the Code were received as a
result of use of the Code by all concerned, and revision work of building byelaws of some States. Based on the
comments and suggestion received the National Building Code of India 1970 was revised in 1983.

(v)
Some of the important changes in 1983 version included : addition of development control rules, requirements
for greenbelts and landscaping including norms for plantation of shrubs and trees, special requirements for low
income housing; fire safety regulations for high rise buildings; revision of structural design section based on new
and revised codes, such as Concrete Codes (plain and reinforced concrete and prestressed concrete), Earthquake
Code, Masonry Code; addition of outside design conditions for important cities in the country, requirements
relating to noise and vibration, air filter, automatic control, energy conservation for air conditioning; and guidance
on the design of water supply system for multi-storeyed buildings.

The National Building Code of India is a single document in which, like a network, the information contained in
various Indian Standards is woven into a pattern of continuity and cogency with the interdependent requirements
of Sections carefully analyzed and fitted in to make the whole document a cogent continuous volume. A continuous
thread of ‘preplanning’ is woven which, in itself, contributes considerably to the economies in construction
particularly in building and plumbing services.

The Code contains regulations which can be immediately adopted or enacted for use by various departments,
municipal administrations and public bodies. It lays down a set of minimum provisions designed to protect the
safety of the public with regard to structural sufficiency, fire hazards and health aspects of buildings; so long as
these basic requirements are met, the choice of materials and methods of design and construction is left to the
ingenuity of the building professionals. The Code also covers aspects of administrative regulations, development
control rules and general building requirements; fire protection requirements; stipulations regarding materials
and structural design; rules for design of electrical installations, lighting, air conditioning and lifts; regulation for
ventilation, acoustics and plumbing services, such as, water supply, drainage, sanitation and gas supply; measures
to ensure safety of workers and public during construction; and rules for erection of signs and outdoor display
structures.

Some other important points covered by the Code include ‘industrialized systems of building’ and ‘architectural
control’. The increase in population in the years to come will have a serious impact on the housing problem. It
has been estimated that the urban population of India will continue to increase with such pace as to maintain the
pressure on demand of accommodation for them. Speed of construction is thus of an utmost importance and
special consideration has to be given to industrialized systems of building. With increased building activity, it is
also essential that there should be some architectural control in the development of our cities and towns if
creation of ugliness and slum-like conditions in our urban areas is to be avoided.

Since the publication of 1983 version of National Building Code of India, the construction industry has gone
through major technological advancement. In the last two decades, substantial expertise has been gained in the
areas of building planning, designing and construction. Also, lot of developments have taken places in the techno-
legal regime and techno-financial regime, apart from the enormous experience gained in dealing with natural
calamities like super cyclones and earthquakes faced by the country. Further, since the last revision in 1983
based on the changes effected in the Steel Code, Masonry Code and Loading Code as also in order to update the
fire protection requirements, three amendments were brought out to the 1983 version of the Code. Considering
these, it was decided to take up a comprehensive revision of the National Building Code of India.

The changes incorporated in the present Code, which is second revision of the Code, have been specified in the
Foreword to each Part/Section of the Code. Some of the important changes are:

a) A new Part O ‘Integrated Approach — Prerequisite for Applying the Provisions of the Code’ emphasizing
on multi-disciplinary team approach for successfully accomplishing build$g/development project, has
been incorporated.
b) New chapters on significant areas like structural design using bamboo, mixed/composite construction
and landscaping have been added.
c) Number of provisions relating to reform in administration of the Code as tdso assigning duties and
responsibilities to all concerned professionals, have been incoprated/modified. Also detailed provisions/
performance to ensure structural sufficiency of buildings, have been prescribed so as to facilitate
implementation of the related requirements to help safely face the challenges during natural disasters
like earthquake.
d) Planning norms and requirements for hilly areas and rural habitat planning, apart from detailed planning
norms for large number of amenities have been incorporated.
e) Fire safety aspects have been distinctly categorized into fire prevention, life safety and fire protection

(vi)
National Building Code Sectional Committee, CED 46

Chairman
Dr H. C. VISVESVARAYA
‘Chandrika’, at 15th Cross, 63-64 East Park Road
Malleswaram, Bangalore 560003

Vice-Chairman
SHRI V. SURESH
P-233/3, Officers Enclave,
Air Force Station, Rajokari, New Delhi 110038

Organization Representative(s)

Ahmedabad Municipal Corporation, Ahmedabad SHFCVATSALS. PATEL


SHRI JAGDISHA. PATEL (Alternate)

Bangalore Mahanagara Palike, Bangalore SHRI M. R. SREENIVASAMURTHY


SHRI R. RAMEGOWDA(Alternate I)
SHRI N. KRISHNA(Alternate II)

Builders Association of India, Mumbai SW B. G. AHUJA

Building Materials and Technology Promotion Council, New Delhi SW T. N. GUPTA


& Smu D. B. N. RAO ‘.-

Bureau of Energy Efficiency (Ministry of Power), New Delhi REPRESEFWATWE

Central Building Research Institute (CSIR), Roorkee SHiw V. K. hhm


Smo B. S. GUPTA
(Alternate)
Central Public Heafth and Environmental Engineering Organisation SHRI B. B. UPPAL
(Ministry of Urban Development and Poverty Alleviation), SHRt V. K. CHAURASIA(Alternate)
New Delhi

Central Public Works Department (Central Designs Organization), CHIEF ENGINEER(DESIGNS)


New Delhi SUPERINTENDINGENGINEER(S& S) (Alternate)

Central Public Works Department (Electrical Department), CHIEF ENGINEER(ELECTRICAL)I


New Delhi

Centre for Disaster Mitigation and Management, Anna University, DIRECTOR


Chennai

Chennai Metropolitan Development Authority, Chennai MEMBERSECRETARY


SHRI N. V. RAKHUNATH(Alternate)

Construction Industry Development Council, New Delhi SHRI P. R. SWARUP


SHRI ANCLCHADHA(Alternate)

Council of Architecture, New Delhi SHRI PRi3MENnRARAJ MEHTA


SHRI SUDHIRVOHRA (Alternate)

Delhi Development Authority, New Delhi ENGINEERMEMBER


CHIEFENGINEER(HQ) (Alternate)

Delhi Fire Service, Government of National Capital Territory SHRI R. C. SHARMA


of Delhi, Delhi

Department of Science and Technology (Ministry of Science SHRI V. RAO ALYAGARI:


and Technology), New Delhi

Directorate General of Employment and Training, New Delhi SHP.I ASHWANIKUMAR

Engineer-in-Chie~s Branch, Army Headquarters, New Delhi BRIG S. K. SHARMA


SHRI D. K. DrNrrER(Alternate)
Forest Research Institute (Indian Council for Forestry Research DIRECTORGENERAL
and Education), Debra Dun DIRECTOR (Alternate)

Housing and Urban Development Corporation Ltd, New Delhi CHAIRMAN& MANAGINGDIRECTOR
SHRI R. K. SAFAYA(Alternate)
Indian Geotechnical Society, New Delhi SHRI D. B. MAHAJAN
DR M. D. DESAI (Alternate)

( viii)
F-

Organization Representative(s)

Indian Institute of Technology (Centre for Energy Studies), PROF N. K. BANSAL


New Delhi
Iudian Roads Congress, New Delhi CHIEF ENGINEER(DESIGN), CPWD
Superintending ENGINEER(DESIGN), CPWD (Alternate)

Institute of Town Plauners, India, New Delhi DR S. K. KULSHRESTHA

Institution of Fire Engineers (India), New Delhi PRESiDENT


GENERALSECRETARY(Alternate)

Ministry of Home Affairs, New Delhi FIRE ADVISOR

Ministry of Home Affairs (Disaster Management Division), SHRI M. P. SAINANI


New Delhi SHRI S. K. SWAMI(Alternate)

Ministry of Non-Conventional Energy Sources, New Delhi DR T. C. TRIPATHI

Ministry of Road Transport and Highways, New Delhi SHKSS. B. BASU


SHRt P. HALDER(Alternate)

Municipal Corporation of Greater Mumbai, Mumbai DIRECTOR(ENGG SERVICES& PROIECTS)


CITY ENGINEER(Alternate)

National Buildings Construction Corporation, New Delhi Sstro B. PRASAD


Smw N. P. AGARWAL(Alternate)

National Council for Cement and Building Materials, Ballabgarh SHRI SHtBAN RAtNA
DR ANIL KUMAR(Alternate)

National Design and Research Forum, The Institution of Engineers PROtI R. NARAYANAIY~NGAR
(India), Bangalore SHRI B. SURESH(Alternate)

National Environmental Engineering Research Institute (CSIR), DR ARINDAMGHOSH


Nagpur DR V. P. DESHPANDE(Altema?e)

North Eastern Council, Shillong SHRI P. K. DEB

Public Works Department (Roads and Buildings), Gandhinagar’ SHRI V. P. JAMDAR


SHRI M. S. JALLUNDHWALA
(Alternate)

Research, Designs and Standads Organization (Ministry of Railways), SHRI R. K. GUPTA


Lucknow SHSUJ. P. DAS (Alternate)

School of Planning and Architecture, New Delhi DtR~CTOR

Structural Engineering Research Centre (CSIR), Chennai Srrru C. V. VAIDYANATHAN


SHRI K. MANI (Alternate)

Suri and Suri Consulting Acoustical Engineers, New Delhi SHRI GAUTAMSURI

The Energy and Resources Institute, New Delhl Ms MILI MAJUMDAR


Ms VIDLSHASALUNKE-PALSULE
(Alternate)

The Indian Institute of Architects, New Delhi SHRI BALBIR VBRMA


SHRSABHIJITRAY (Alternate)

The Institution of Engineers (India), Kolkata PROF G. P. LAL


SHRI O. P. GOBL (Alternate)

Tbe Institution of Surveyors, New Delhi SHRI K. S. KHARB


SHR1R. K. BHALLA(Alternate)

Town and Country Planning Organization, New Delhi SHRI K. T. GORUMUKHI


SHRI J. B. KSHtRSAGAR(Altemare)

U.P. Housing and Development Board, Lucknow SHRt HARt GOPAL

Unitech Ltd, Gurgaon SHR] SUSH]LSHARMA


SHRI SHAHtDMAHMOOD(Alternate)

Impersonal capacity (5, Sunder Nagar, New Delhi l10003) DR J. R. BHALLA

BIS Directorate General SHRI S. K. JAIN, Director & Head (Civil Engineering)
[Representing Director General (Ex-of/icio Mernberj

Member Secretary
SHRI SANJAYPANT
Joint Director (Civil Engineering)

(ix)
Special Panel for Guiding and Co-ordinating the
Revision of National Building Code of India, CED 46:SP

Organization Representative(s)

In personal capacity (P-233/3, Oflcers Enclave, Air Force Station, SHRI V. SI.JF.ESH(Convener)
Rajokari, New Delhi 110 038)

Building Materials and Technology Promotion Council, New Delhi SHRS T. N. GUPTA
Central Building Research Institute (CSIR), Roorkee SHSUV. K. MATHUR

Central Public Works Department, New Delhi SHKSH. S. DOGRA

Council of Architecture, New Delhi SHRI PREMENDRARAJ MEHTA

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi LT-GriN HARSUNIYAL

The Institution of Engineers (India), Kolkata PROF G. P. LAL


SHRI O. P. GOEL (Alternate)

Bureau of Indian Standards, New Delhi SHSUSANJAYPANT

Ad-hoc Group for Part Oof NBC, CED 46:AG

Organization Representative(s)

In personal capacity ( ‘Chandrika’, at 15th Cross, 63-64, East Park Road, DR H. C. VLSVESVAKAYA
(Convener)
A4alleswaram, Bangalore 560 003)

Council of Architecture, New Delhi SHRI PREiMENDRA


RAI MEHTA

In personal capacity (P-233/3, Ofticers Enclave, Air Force Station, SHRI V. SUKESH
Rajokari, New Delhi 110 038)

In personal capacity (A-39B, DDA Flats, Munirka, New Delhi 110 067) SHRI P. B. VUAY

In personal capacity (EA-345, Maya Enclave, New Delhi 110 064) SHRI J. N. BHAVANtPRASAD

Panel for Administration, Development Control Rules and


General Building Requirements, CED 46:P1

Organization Representative(s)

In personal capacity (P-233/3, Oficers Enclave, Air Force Station, SHRI V. SURESH(Converser)
Rajokari, New Delhi 110 038)

Ahmedabad Municipal Corporation, Ahmedabad REPRESENTATIVE

Building Materials and Technology Promotion Council, New Delhi SHRI T. N. GWTA
SHRI RAJESHMALIK (Alternate)

Central Building Research Institute (CSIR), Roorkee SHRI V. K. MATHUR


SHRI N. K. SHANGARI(Alternate)

Central Public Works Department, New Delhl SHRI R. S. KAUSHAL


SHFUSANIIB SENGUFTA(Alternate)

Consulting Engineers Association of India, New Delhi SHRI S. C. MEHROTRA


SHRI N. F. PATEL(Alternate)

Council of Architecture, New Delhi SHSUPREMENDRARAJ M@TA


SHRI SoDmR VOHRA(Alternate)

Delhi Development Authority, New Delhi SHRI R. C. KINGER


SEW A. K. GUPTA(Alternate)

Housing and Urban Development Corporation Ltd, New Delhi SHRI K. C. BATRA

Indian Association of Structural Engineers, New Delhi SHRI MAHENDRARAJ

Institute of Town Planners (India), New Delhi DR S. K. KUtXHRESTHA

Municipal Corporation of Delhi, Delhi ENGtNEER-IN-CHtEF


SrrRI M. M. DAS(Alternate)

Municipal Corporation of Greater Mumbai, Mumbai CHIEF ENGINEER(DWELOPMENTPLAN)


DtwTY ClttETENoamaR (DEWLOPMENT
PLAN)-I(Alternate)

National Council for Cement and Building Materials, Ballabgarh DR ANIL KUMAR

(x)
-T-

Orgarrizcrtion Representative(s)

National Real Estate Development Council, New Delhi BRIG R. R. SINGH (RETD)

School of Planning and Architecture, New Delhi PROF SUBIR SAHA

The Indian Institute of Architects, Mumbai SHRt BALBIR VERMA


SHR] ABHU]TRAY (Alfernate)

The Institution of Engineers (India), Kolkata SHRI A. D. SHIRODE


SHR] P. B. VLIAY(Alternate)

Town and Country Planning Organization, New Delhi SHRI J. B. KSHIRSAGAR


SHRI R. SRINWAS(Alternate)

Panel for Fire Protection, CED 46:P2

Organization Representative(s)

In personal capacity (29/25, Old Rajendra Nagar, New Delhi 110 060) SHRI S. K. DHERI (Convener)

Central Building Research Institute (CSIR), Roorkee DR T. P. SHABMA


DR GOPAL KRISHNA(Alternate)

Central Public Works Department, New Delhi SHRI ARVIND KANSAL


SHRI R. S. KAUSHAL(Alternate)

Deolalikar Consultants Pvt Ltd, New Delhi SHRI S. G. DEOLALIKAR

Directorate of Town and Country Planning, Government Gf Tamil Nadu, SHRI S. DHANASEKARAN
Chennai SHRI R. RA.JAGOPALAN
(Alternate)

Engineer-in-Chie~s Branch, Army Headquarters, New Delhi SHRt R. A. DUBEY


SHP.IAJAY SHANKAR(Alternate)

Institution of Fire Engineers (India), New Delhi SHRI U. S. CHHILLAR


SHRI S. P. BATRA(Alrerrrate)

Lloyd Insulations (India) Ltd, New Delhi SHRI SANJEEVANGRA


.%-m K. K. MrTBA (Altemafe)

Ministry of Home Affairs, New Delhi SHat OM PRARASH


SHRI D. K. SHAMMI(Alternate)

Delhi Fire Service, Government of National Capital Territory of Delhi, SHIU R. C. SHARMA
Delhi SHRI G. C. MISRA (Alternate)

Municipal Corporation of Greater Mumbai (Mumbai Fire Brigade), SHRI A. D. JHANDWAL


Mumbai SHRI V. H. NAIK (Alternate)

National Council for Cement and Building Materials, Ballabgrrrh DR ANIL KUMAR

National Fire Service College (Ministry of Home Affairs), Nagpur DR K. C. WADHWA


SHRI SHAMIM(Alfemate)

Oil Industry Safety Directorate, New Delhi SHRI D. JAGANNATH


SHRI S. K. AGGARWAL(Alternate)

Regional Research Laboratory (CSIR), Jorhat REPRBSENTATWB

Spectral Services Consultants Pvt Ltd, New Delhi SHRI SANDBEPGOEL

Tariff Advisory Committee, Mumbai SHRI Z. U. ISLAM


SHRI D. N. SAHA (Alternate)

The Institution of Engineers (India), Kolkata PROF M. P. CHOWDIAH


SHR1K. B. RAJORtA(Alternate)

In personal capacity (P-233/3, Ofjlcers Enclave, Air Force Station, SHRI V. SURESH
Rajokari, New Delhi 110 038)

Panel for Building Materials, CED 46:P3

Organization Representative(s)

Building Materials and Technology Promotion Councils, New Delhi SHRI T. N. GUmA (Convener)

Central Building Research Institute (C.’WR), Roorkee DR C. L. VERMA


SHRI L. K. AOARWAL(Alternate)

Central Public Works Department, New Delhi SHRI H. K. L. MEHTA


SHFOR. C. GUFTA (Alternate)

(xi)
Organization Representative(s)

Council of Architecture, New Delhi SHRI ANURAGROY


SHRI ATUL GUPTA (Alternate)

Department of Science and Technology (Ministry of Science and SHRI SOUMITRABISWAS


Technology), New Delhi SHRI G. SRIRANTH(Alternate)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi SHRI A. K. SINGH


SHR1P. K. GUPTA(Alremate)

Housing and Urban Development Corporation Ltd, New Delhi CHAIRMANAND MANAGINGDIRECTOR
SHRI S. K. TANEIA(Alternate)

Indian Plywood Industries Research and Training Institute, SHR1 K. SHYAMASUNDAR


Bangalore SHRI M. PAWANKGMAR(Alternate)

National Council for Cement and Building Materials, Ballabgarh SHRI SHIBANRAtNA
DR K. MOHAN (Alremate)

The Institution of Engineers (India), Kolkata SHRSG. L. RAO


SHRI R. S. GOEL (Alternate)

Panel for Loads, Forces and Effects, CED 46:P4

Organization Representative(s)

National Council for Cement and Building Materials, Ballabgarh DRANtLKUMAR (Converter)
_
Building Materials and Technology Promotion Council, New Delhi SHRI T. N. GUPTA
SW I. S. StDHG (Alternate)

Central Building Research Institute, Roorkee SHRI B. S. GUPTA


SHRI A. K. MrtTAL (Alternate)

Central Public Works Department, New Delhi SHRI N. M. D. JAtN


Ssnrt ABHAYSrNHA(Alternate)

Centre for Disaster Mitigation and Management, Anna University, DR R. K. BHANDASU


Chennai
Mahendra Raj Consultants Pvt Ltd, New Delhi SHRI MAHENDRARAJ
SHRI J. GHOS~ (Alternate)

Structural Engineering Research Centre (CSIR), Chennai SHRI C. V. VASDYANATHAN


SHRI K. MANI (Alternate)

The Institution of Engineers (India), Kolkata SHRI P. P. DHARWADKAR

In personal capacity (Professor of Bridge Engineering, Railway Chair, DR PREM KRtSHNA


Department of Civil Engineering, Indian Institute of Technology,
Roorkee 247 667)

In personal capacity (Emeritus Scientist, Structural Engineering DR T. V. S. R. APPA RAO


Research Centre, Madras CSIR Campus, Taramani,
Chennai 600 113)
In personal capacity (P-233/3, OJjicers Enclave, Air Force Station, SHRI V. SURESH
Rajokari, New Delhi 110 038)

Panel for Soils and Foundations, CED 46:P5


#
Organization Represenhtive(s)

Centre for Disaster Mitigation and Management, Anna University, DR R. K. BHANDARS


(Convener before 19 September 2003)
Chenrmi

Central Building Research Institute (CSIR), Roorkee Smu CHANORA


PRAKASH(Convener since 19 September 2003)
DR SURENDRAKrrMAR(Alternate)

Afcons Infrastructure Limited, Mumbai SHRTS. B. JOSHI


SHRI D. G. BHAGWAT(Alternate)

Central Public Works Department, New Delhi SHRI BHAGWANSINGH


Smu R. K. StNGHAL(Alternate)

Delh] Development Authority, New Delhi SHRI S. P. RUSTGGI


SHRI J. M. JOSHI (Alternate)

( xii)
Organization Representative(s)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi COL R. N. MALHOTRA


COL N. B. SAXENA(Alternate)

Indian Cieotechnical Society, New Delhi MAJ GEN S. N. MUKEKJEE


SHRI SANIAYGUPTA (Alternate)

National Council for Cement and Building Materials, Ballabgarh DR AN[L KUMAR
SHRXH. K. JULKA(Alternate)

The Institution of Engineers (India), Kolkata PROF JANARDANJHA

Panel for Timber, CED 46:P6

Organization Representative(s)

In personal capacity (Pratap Nursery Lane, Near Gurdwara, SHSUK. S. PRUTHI(Convener)


Pandihvari, Debra Dun 248007)
Bamboo Society of India, Bangalore SHRI A. C. LAKSHMANAN
DR K. A. KUSHALAPPA(Alternate)

Building Materials and Technology Promotion Council, New Delhi SHRI T. N. GUPTA
SHRI RAJESHMALIK (Altemare)

Central Building Research Institute (CSIR), Roorkee SHKt S. K. MrrrAL


SHRSB. S. RAWAT(Alternate)

Central Public Works Department, New Delhi SHRSMATSP. VERMA


SHru G. C. KHATTAR(Alternate)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi SHRI A. K. SINGH


SHRI P. K. GUPTA(Alternate)

Forest Research Institute (Indian Council for Forestry Research SHtU B. K. BHATIA
and Education), Debra Dun

Housing and Urban Development Corporation Ltd, New Delhi CHAIRMANAND MANAGINGDIRECTOR
SHRI S. K. TANEIA(Alternate)

Indian Plywood Industries Research and Training Institute, SHRt K. SHYAMASUNDAR


Bangalore SHRI H. GURUVARBDDY(Alternate)

North Eastern Council, Shillong SHRt P. K. DEB

The Institution of Engineers (India), Kolkata SHRI KRISHNAKUMAR

In personal capacity [No. 179 (710), 24th B-Cross, 3rd Block, DR H. N. JAGADEESH
Jayanagar, Bangalore 560 011]
In personal capacity (103/11, Vasant Vihar, P. O. New Forest, SHRI S. S. RAJPUT
Debra Dun 248 006)

Panel for Masonry, CED 46:P7

Organization Representative(s)

Delhi Tourism and Transportation Development Corporation, SHRI JOSE KUWAN (Convener)
New Delhi

Building Materials and Technology Promotion Council, New Delhi SHRt T. N. GUmA
SHRI PANKAJGUPTA <Alternate)

Central Building Research Institute (CSIR), Roorkee SHRI A. K. MITTAL


Srrro SHAILSSHKUMAR(Alternate)

Central Public Works Department, New Delhi DR A. K. MtITAL


SHRI NEERM MISHRA (Alternate I)
Smrr A. K. JHA (Alternate 11)

Delhi Development Authority, New Delhi SHRI S. P. RUSTOGI


SHRI J. M. JOSHI (Alternate)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi SHIG D. R. KURDIYA


Srmt SUBODHKUMAR(Alternate)

Indian Institute of Science (Centre for Astra), Bangalore DR B. V. VENKATARAMA REDDY


DR K. S. NANIUNDARAO (Alternate)

( xiii)
Organization Representative(s)

Indian Institute of Technology, Kanptu DR DLIRGESHC. RAI


DR C. V. R. MURTY (Alternate I)
DRSUDHIRK. JASN(AltematelI)

Indian Institute of Technology, New Delhi DR S. N. SINHA

Public Works Department, Government of Maharashtra, Mumbai SHRI P. K. NINAVE

Structural Engineering Research Centre (CSIR), Chennai SHRIR. JAYARAMAN


SHRI A. CHELLAPPAN(Alternate)

The Institution of Engineers (India), Kolkata SHRI S. L. GARG

Panel for Plain, Reinforced and Prestressed Concrete, CED 46:P8

Organization Representative(s)

In personal capacity (35, Park Avenue, Annamma, Naicker Street, DR C. RAIKUMAR(Convener)


Kuniamuthur, Coimbatore 641 008)

Central Building Research Institute (C SIR), Roorkee DR B. S. GUPTA


DR B. K. RAO (Alternate I)
DR AWADESHKUMAR(Alternate 11)

Central Public Works Department, New Delhi SHRI N. M. D. JMN


SHP.IABHAYSrNHA(Alternate)

Delhi Tourism and Transportation Development Corporation, SHRI JOSE KURIAN


New Delhi

Gammon India Ltd, Mumbai SHRI S. A. REDDI

Hindustan Prefab Limited, New Delhi SHRI HAZARILAL


SHRSM. KUNDU(Alternate)

Larsen and Toubro Ltd, ECC Construction Group, Chennai SHRI K. P. RAOHAVAN
SHRI S. KANAPPAN(Alternate)

Ministry of Road Transport and Highways, New Delhi SHRI T. B. BANERJEE


SHRI SATISHKUMAR(Alternate)

National Council for Cement and Building Materials, Ballabgarh DK ANIL KUMAR
SHRI H. K. JULKA(Alternate)

Research, Designs and Standards Organization (Ministry of Railways), SHRI R. K. GUPrA


Lucknow SHRI J. P. DAS (Aitemate I)
SHRI A. K. GUPTA(Alternate II)

Structural Engineering Research Centre (CSIR), Chennai DR N. LAKSHMANAN


SHSUH. G. SREENATH(Alternate)

Tandon Consultants, New Delhi SHRI MAHESHTANDON

The Institution of Engineers (India), Kolkata SHRI S. S. CHAKRABARTY

Panel for Steel, CED 46:P9


Organization Representative(s)

MECON Ltd, Ranchl SHRI A. BASU (Convener)

Central Public Works Department, New Delhi CHIEF ENGINEER ,


SUPRtNTENDtNG
ENGA (P&A) (Alternate)

Engineer-in-Chief’s Branch, Army Headq~arters, New Delhi SHRI D. K. DtNKER


COL V. K. TYAGt (Alternate)

Indian Institute of Technology, Chennai DR V. KALYANARAMAN

Institute for Steel Development and Growth, Kolkata DR T. K. BANnYOPADHYAY


SW km GUHA (Alternate 1)
SHro P. L. RAO (Alternate 11)

Kalpataru Power Transmission Ltd, Gandhinagar SHRI M. C. MEHTA


SHRI B. K. SATtSH (Alternate)

M. N. Dastur and Co Ltd, Kolkota SHRt SATYASGSEN


Srrm TAPANKUMARBHAUMIK(Alternate)

( xiv)
Organization Representative(s)

Research, Designs and Standards Organization (Ministry of Railways), SHRTR. K. GUmA


Luckncsw SHRI D. K. SINGH(Alternate)

SPECO Engineering Pvt Ltd, New Delhi SHRI ONKAR SINGH

Structural Engineering Research Centre (CSIR), Chennai DR S. SEETHARAMAN


SHRI S. ARUL JAYACHANDRAN(Alternate)

The Institute of Engineers (India), Kolkata SHRI R. P. GUPTA

Panel for Prefabrication and Systems Buildings, CED46:P1O

Organization Representative(s)

Larsen and Toubro Ltd, Chennai SHRI A. RAMAKRISHNA(Convener)


SHRI K. V. RANGASWAMX
(Alternate)

B. G. Shrike Construction Technology Pvt Ltd, Pune SHRI G. R. BHARITKAR


SHRI R. P. JAKHALEKAR(Alternate)

Central Building Research Institute (CSIR), Roorkee SHR1B. N. HIRA


SHRI D. K. GAUTAM (Alternate)

Central Public Works Department, New Delhi CHIEF ENGCNEER(NDZ-111)


SHRI A. K. GARG (Alternate)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi COL R. N. MALHOTRA


SHRI P. K. GUPTA(Alternate)

Hindustan Prefab Limited, New Delhi SHR] HAZARI LAL


SHRI M. KUNDU (Alternate)

Institute for Steel Development and Growth, Kolkata DR T. K. BANDYOPADHYAY


SHRI ALOK BABHYA (Alternate)

Lloyd Insulations (India) Ltd, New Delhi SHRt MOHtT KHANNA


SHRI K. K. MtTRA (Alternate)

National Counci I for Cement and Building Materials, Ballabgarh SHRI H. K. JULKA
SHRI SATISHSHARNtA(Alternate)

Shirish Patel and Associates Consultants Pvt Ltd, Mumbai SHR[ SHIRISHB. PATEL
SHRJ P. H. SRINWASACHAR
(Alternate)

Structural Engineering Research Centre (CSIR), Chennai SHRI H. G. SREENATH


SHRI R. JAYARAMAN (Alternate)

System Building Technologists, New Delhi SHRI G. B. SINGH

The Indian Institute of Architects, Mumbai SHRI S. R. SIKKA

The Institution nf Engineers (India), Kolkata DR R. K. BHANDARI


SHFUP. B. VrJAY (Alternate)

Panel for Constructional Practices and Safety, CED 46:P11

Organization Representative(s)

In personal capacity (103, Charak Sadan, Vikaspuri, SHRI P. ICVJSHNAN(Convener)


New Delhi 110 018)

Adlakha and Associates, New Delhi SHRI PRAMOD ADLAKHA

Builders Association of India, Mumbai SHRI RAJ PAL ARORA

Central Building Research Institute (CSIR), Roorkee SHRt N. K. SHANGAR]


SHRI B. S. GUPTA (Alternate)

Central Public Works Department, New Delhi SHSU R. P. BHARDWAJ

Construction Industries Development Council, New Delhi SHRI P. R. SWARUP


SHRI SUNIL MAHAJAN (Alternate)

Director General of Factory Advice Service and Labour Institute SHRI S. K. DUITA
(Ministry of Labour), Mumbai SHRI I. ROYCHOWDHURI(Alternate)

(xv)
Organization Representative(s)

Engineer-in-Ch]efs Branch, Army Headquarters, New Delhi SHRI DINESH SIKAND


SHR1A. K. SrNGII (Alternate)

Engineers India Limited, New Delhi SHRI M. P. JAIN


SHR] A. K. TANDON(Alternate)

Gammon India Ltd, Mumbai SHRI K. N. CHATrERIEE


SHRI S. C. SARIN (Alternate)

Indian Plywood Industries Research and Training Institute, SHRI H. GURUVA REDOY
Bangalore SHRt M. PAVAN KOMAR (Alternate)

Larsen and Toubro Ltd, Chennai SHRt R. P. SAKUNIA

National Building Construction Corporation, New Delhi SHRI B. PRASAD


SHRI N. P. AGARWAL(Alternate)

School of Planning and Architecture, New Delhi DR V. THIRUVENGADAM

The Indian Institute of Architects, Mumbai SHRI KAILASHCHANDRAJAITIA


SHRSC. M. SAPRA(Alternate)

The Institution of Engineers (India), Kolkata SHRTH. P. JAMDAR


,%rm K. B. RAJORIA(Alternate)

Panel for Lighting and Ventilation, CED 46:P12

Organization Representative(s)

Central Building Research Institute (CSIR), Roorkee SHRI V. K. MATHOR(Convener)


DR lSHWARCHAND(Alternate 1)
SHFUSNREEKOMAR(Alternate II)

All India Institute of Hygiene and Public Health, Kolkata DR GAUTAM BANERJEE

Bureau of Energy Efficiency (Ministry of Power), New Delhi REPRESENTATIVE

Central Public Works Department, New Delhi CHtEF ENGtNEBR(E) II


SUPBRtNTENDINGENGINEER(E) P (Alternate)

Council of Architecture, New Delhi PROF VINOD KUMAR GUPTA


1,
Director Generat Factory Advice Service and Labour Institute SHRJS. K. DUTTA
(Ministry of Labour), Mumbai SHru I. ROYCHOWDHUSU
(Alternate)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi SHRI S. K. MAHESHWARt


SHRSA. C. VW (Alternate)

Indian Society for Lighting Engineers., New Delhi SHRI P. K. BANDYOPADHYAY

Ministry of Non-Conventional Energy Sources, New Delhi SHRt BIBEK BANDYOPADHYAY

Municipal Corporation of Greater Mumbai, Mumbai SHRI P. G. CHAVAN


SHRI R. K. RAHATE (Alternate)

National Physical Laboratory (CSIR), New Delhi DR H. C. KANDPAL

Philips India Ltd, Mumbai SHRIMATISUDESHNAMUKHOPADHYAY


SHRI S. P. TAMBE,(Altemate)

School of Planning and Architecture, New Delhl PROF ARVIND KISHAN

The Indian Institute of Architects, Mumbai PROF ASHOK B. LALL


The Institution of Engineers (India), Kolkata PROF C. S. JHA ‘

Panel for Electrical Installations, CED 46:P13

Organization Representative(s)

In personal capacity (EA 345, Maya Enclave, New Delhi 110 064) SHRI J. N. BHAVANtPRASAD(Convener)

Bureau of Energy Efficiency (Ministry of Power), New Delhi REPRESENTATIVE

Central Electricity Authority, New Delhi CHIEF ENOtNEER(DP & D)


DIRECTOR(UT) (Alternate)

Chief Electrical Inspectorate, Tamil Nadu SHRI S. SUBRAMANIAN


Wrrrr M. KAMALBATCHA(Alternate)

(xvi)
Organization Representative(s)

Engineer-in-Chie~s Branch, Army Headquarters, New Delhi Smu AIAY SHANKAR


Smu Smv OM PRAKASH(Alternate)

Engineers India Ltd, New Delhi SHRI A. ANANTHANARAYAN


SHFUN. SETHI (Alternate) .

Fairwood Consultants Pvt Ltd, New Delhl SMT SHRUTKGOEL

Siemens Ltd, Chennai SHRI HEMANTTUNGARE


SHRI AJIT DESHPANDE(Alternate)

The Institution of Engineers (India), Kolkata PROF SAMIRANCHOUDHARY


LT GEN S. K. JAtN (Alternate)

Panel for Air Conditioning and Heating, CED 46:P14

Organization Representative(s)

Spectral Services Consultants Pvt Ltd, New Delhi DR PREM C. JMN (Convener)
SHR1ASHISH RAKHEIA (Alternate)

Airtron Consultants, Bangalore SHRt R. V. SIMHA

Air Treatment Engineering Pvt Ltd, Chennai SHRI K. P. S. RAMESH

Blue Star Limited, Mumbai SHRI JITENDRAMORESHWARBHAMBURE

Bureau of Energy Efficiency (Ministry of Power), New Delhi REPRESENTATIVE

Central Building Research Institute (CSIR), Roorkee DR ISHWARCHAND


SHRI B. M. SUMAN (Alternate)

Central Public Works Department, New Delhi SHRt S. R. SUBRAMANIAN


SHSUS. P. BARANWAL(Alternate)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi SHRI NARENDRA KUMAR


SHR1R. A. DUBEY (Alternate)

Hi-Tech Consultant, New Delhi SHRI N. S. HUKMANI

Indian Institute of Technology, New Delhi DR R. S. AGARWAL

Indian Society for Heating, Refrigeration and Air-Conditioning SHRI N. S. HUKMANI


Engineers, New Delhi

Sterling India Consulting Engineers, New Delhi SHRI G. C. MODGIL

Suvidha Engineers India Ltd, Noida SHRt ALOK C. TANDON

Tbe Institution of Engineer (India), Kolkata SHRI PRADEEPCHATURVEDI

Voltas Limited, New Delhi SHRI S. M. KULKARNI


SHRI ATUL MALIK (Alternate)

In personal capacity (K-43, Kailash Colony, New Delhi 110 048) SHRI M. M. PANDE

Panel for Acoustics, Sound Insulation and Noise Control, CED 46:P15

Organization Representative(s)

Suri and Suri Consulting Acoustical Engineers, New Delhi SHRI GAUTAM Suru (Converrer)

All India Radio, New Delhi SHRI DEEPAK MEHROTRA


SHRt S. MUTHUSWAMY
(Alternate)

Central Building Research Institute (CSIR), Roorkee SHRI R. K. SRIVASTAVA


SHRI R. L. DHABAL(Alternate)

Central Public Works Department, New Delhi SHRI K. A. ANANTHANARAYANAN


SHRI N. NAGARAJAN(Alternate)

Engineer-i n-Chie~s Branch, Army Headquarters, New Delhi BRIG S. K. SHARMA


SHRIMATIANURADHABHAStN (Alternate)

Indian Institute of Science, Bangalore PROF M. L. MUNJAL

Indian Institute of Technology, Chennai PRoi= S. NARYANAN


DR A. RAMACHANDRAIAH(Alternate)

Indian Institute of Technology, Kharagpur DR A. R. MOHANTY

( xvii)
Organization Representative(s)

Lloyd Insulations (India) Pvt Ltd, New Delhi SHRI N. SRINIVAS


SHar B. S. JAMWAL(Alternate)

National Physical Laboratory (CSIR), New Delhi DR V. MOHANAN


DR OMKAR SHARMA (Alternate)

School of Planning and Architecture, New Delhi PROF (DR) SHOVAN K. SAHA

The Indian Institute of Architects, Mumbai SHR[ INDRANATHBASU

The Institution of Engineers (India), Kolkata SrrRS K. V. CHAUBAL


SHKSP. K. ADLAKHA(Alternate)

Panel for Installation of Lifts and Escalators, CED 46:P16

Organization Representative(s)

KONE Elevators India Ltd SHR1A. SANKARAKRISHNAN(Convener)


SHRSL. N. VENKATRAMAN(Alternate I)
Smu S. EMANUELRAJASEKARAN(Alternate II)
Central Public Works Department, New Delhi SHRt J. K. CHAUDHURY
Smu A. S. LUTHRA (Alternate)

Chief Electrical Inspectorate, Government of Delhi, New Delhi Srmt K. L. GROVER


SI-KUA. K. AOGARWAL
(Alternate)

Chief Electrical Inspectorate, Govt of Tamil Nadu, Chennai Smn S. SuaRAMANIAN


SHRS M. KAMAL BATCHA (Alternate) &-

Delhi Development Authority, New Delhi Stint S. K. SmHA


Sma N. K. GUPTA
(Alternate)

ECE Industries Ltd, Ghaziabad Smu P. K. BANKA


SHSU JAOAT MOHAN (Alternate)

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi SHRS RAMA NATH


Smu M. L. BANSAL(Alternate)

Otis Elevator Company (India) Ltd, New Delhi Smt V. S. MOHAN


Smu S. P. RAO (Alterndte I)
Srntr ANURAG MANGLIK(Alternate II)

Public Works Department, Government of Maharashtra, Mumbai Ssrru A. M. THATTE


SHSGS. D. WAN (Alternate)

Schindler India Pvt Ltd, Mumbai SHRI RONNtE DANTE


SHtU T. A. K. MATHEWS (Alternate)

The Institution of Engineers (India), Kolkata SHRI JAGMANStNGH


DR R. K. DAVE (Alternate)

In personal capacity [4, Vidharbha Samrat Co-operative Housing SHRI A. S. HERWADKAR


Socie@, 93 C, V. P. Road, Vile Parle (West), Mumbai 400 056]

Panel for Plumbing Services, CED 46:P17

Organization Representative(s)

Deolalikar Consultants Pvt Ltd, New Delhi SHRI S. G. DEOLALIKAR(Convener)

Birhatr Mumbai Licenced Plumbers Association, Mumbai PRESIDENT


SHst H. CX~GANDrrr(Alternate)

Central Building Research Institute (CSIR), Roorkee SHRI SORESHKOMAR%urMA


SHSUAIAY StNGH (Alternate I)
SHSGR. S. CmMora (Alternate 11)
Central Ground Water Board. New Delhi DR SALEEMROMANS
SHIG S. K. SHARMA(Alternate)

Central Pollution Control Board, New Delhi DR A. B. AKOLKAR


DR M. SUNDARSVADWAL(Alternate)

Central Public Works Department, New Delhi Smu H. S. DOGRA


SHRI A. K. SINHA(Alternate)

Delhi Development Authority, New Delhi SHRI S. P. RUSTOG1


SHru G. K. SEITU (Alternate)

( xviii)
Organization Representative(s)

Delhi Jal Board, New Delhi SHRI SUBHASHCHANDER

Engineer-in-Chief’s Branch, Army Headquarters, New Delhi SHRI JITENDRASINGH


SHRLSURYAPRAKASH(Alternate)

Indian Plumbing Association, New Delhi SHRI SUDHAKARANNAIR


SHRLP. RAMACHANDRAN
(Alternate)

Indraprastha Gas Ltd, New Delhi SHRLPEEYUSH TRIPATHI


SHRI C. S. SAGAR (Alternate)

Municipal Corporation of Delhi, Delhi ENGINEER-IN-CHSEF


SHRI M. M. DAS (Akerrrare)

Municipal Corporation of Greater Mumbai, Mumbai SHRI T. V. SHAH


Smu V. R. PEDHNEKAR(Ahemate)

National Environmental Engineering Research Institute (CSIR), DR APURBAGUPTA


Nagpur SHR] P. S. KELKAB(Alternate)

Spectral Services Consultants Pvt Ltd, New Delhi SHRLSANDEEPGOBL

The Indian Institute of Architects, Mumbai SHRI UDAY PANDE

The Institution of Engineers (India), Kolkata SHRI P. C. TYAGI

In personal capacity (B/58A, Gangotri Enclave, Alaknanda, SHRI J. D’ CRUZ


New Delhi 110 019)
In personal capacity (Principal Advisor, School of Environment DR D. K. CHADHA
Management, Guru Gobind Singh Indraprastha University,
Keshmere Gate, Delhi 110 006)
In personal capacity (610, Technology Apartments, 24, Palparganj, SHRI SUBIR PAUL
Delhi 110 092)

Panel for Landscaping, Signs and Outdoor Display Structures, CED 46:P18

Organization Representative(s)

In personal capacity (5, Sunder Nagar, New Delhi 110003) DR J. R. BHALLA(Convener)


Central Public Works Department, New Delhi SHRIARVIND KANSAL
SHRI A. N. DEVUCAR(Alternate)

Council of Architecture, New Delhi KUMARIVLNITAC. K. VIIAYAN

Delhi Urban Arts Commission, New Delhi SHRI H. K. ~A~AV


SHRI DLNANATH (Alternate)

Housing and Urban Development Corporation, New Delhi SHRI R. K. SAFAYA

Institute of Town Planners, India, New Delhi DR S. K. KULSHRESTHA

Municipal Corporation of Delhi, Delhi SHRLS. S. HADLCE


SHRI S. RAMZSH(Alternate)

Municipal Corporation of Greater Mumbai, Mumbai SHRLM. S. GHAG


SHRLR. K. RAHATE(Alternate)

National Institute of Design, Ahmedabad Smrt ANANDODUTTA


SW J. G. SEVAK
(Alternate)

Selvel Publicity and Consultants Pvt Ltd, Mumbai SHRS K. S. NICHOLSON

Shaheer Associates, New Delhi PROF M. SHAHEER

Town and Countrv Planning . Organization,


. New Delhi SHRLJ. B. KSHWCSAGAR
SHRt Y. RAMESH(Alternate)

The Indian Institute of Architects, Mumbai SHRI MAHW.HPALLWAL

The Institution of Engineers (India), Kolkata PROF JITENDRASINGH

In personal capacity (D-198, Defence Colony, New Delhi 110024) SHRI RAWNDRABHAN

Member Secretaq
SHRI SANIAY PANT
Joint Director (Civil Engineering)
Joint Member Secretary
SHRI S. K. VERMA
Deputy Director (Civil Engineering)

(xix)
-,
(J 6$
Important Explanatory Note for Users of Code

In this Code, where reference is made to ‘accepted standards’ in relation to


material specification, testing or other related information or where reference
is made to ‘good practice’ in relation to design, constructional procedures or
other related information, the Indian Standards listed at the end of the
concerned Parts/Sections may be used to the interpretation of these terms.
At the time of publication, the editions indicated in the above Indian Standards
were valid. All standards are subject to revision and parties to agreements
based on the Parts/Sections are encouraged to investigate the possibility of
applying the most recent editions of the standards.
In the list of standards given at the end of each Part/Section, the number
appearing in the first column indicates the number of the reference in that
Part/Section. For example:
a) accepted standard [3( 1)] refers to the standard given at serial number
1 of the list of standards given at the end of Part 3, that is IS 8888
(Part 1) :1993 ‘Guide for requirements of low income housing:
Part 1 Urban area (jirst revision)’.
b) good practice [6-5 A(22)] refers to the standard given at serial number
22 of the list of standards given at the end of sub-section 5A of Part 6,,
that is IS 4926:2003 ‘Code of practice for ready-mixed concrete
(second revision)’.
c) accepted standard 7(9) refers to the standard given at serial number 9
of the list of standards given at the end of Part 7, that is IS 2925:1984
‘Specification for industrial safety helmets (second revision)’.
d) accepted standard [8-5(4)] refers to the standard given at serial number
2 of the list of standards given at the end of Section 5 of Part 8, that
is IS 14665 (Part 3/See 1 and 2) :2000 ‘Electric traction lifts: Part 3
Safety rules, Section 1 Passenger and goods lifts, Section 2 Service
lifts’.
e) good practice [9-2(3)] refers to the standard given at serial number 3
of the list of standards given at the end of Section 2 of Part 9, that
is IS 8198 (Part 5) : 1984 ‘Code of practice for steel cylinders for
compressed gases: Part 5 Liquefied petroleum gas (LPG) (j%irst
revision)’. ,,

( xxi)
INFORMATION FOR THE USERS

For the convenience of the users, this publication is also available in the following five groups of the National
Building Code of India 2005 each incorporating the related Parts/Sections dealing with particular area of building
activity:

Group 1 For Development, Building Part o: Integrated Approach — Prerequisite for Applying
Planning and Related Provisions of the Code
Aspects Part 2: Administration Part 3: Development Control Rules
Part 4: Fue and Life Safety and General Building Requirements
Part 5: Building Materials
Part 10: Landscaping, Signs and Outdoor Display Structures
Section 1 Landscape Planning and Design
Section 2 Signs and Outdoor Display Structures

Group 2 For Structural Design and Part o: Integrated Approach — Prerequisite for Applying
Related Aspects Provisions of the Code
Part 6: Structural Design
Section 1 Lo~ds, Forces and Effects
Section 2 Soils and Foundations
Section 3 Timber and Bamboo
3A Timber
3B Bamboo
Section 4 Masonry
Section 5 Concrete
5A Plain and Reinforced Concrete
5B Prestressed Concrete
Section 6 Steel
Section 7 Prefabrication, Systems Building and
Mixed/Composite Construction
7A Prefabricated Concrete
7B Systems Building and Mixed/
Composite Construction

Group 3 For Construction Related Part o: Integrated Approach — Prerequisite for Applying
Aspects including Safety Provisions of ‘tie Code
Part 7: Constructional Practices and Safety

Group 4 For Aspects Relating to Part o: Integrated Approach — Prerequisite for Applying
Building Services Provisions of the Code
Part 8: Building Services
Section-l Lighting and Ventilation
Section 2 El~tric~l and Allied Installations
Section 3 Air conditioning, Heating and Mechanical
Ventilation
Section 4 Acoustics, Sound Insulation and Noise
Control
Section 5 Installation of Lifts and Escalators

Group 5 For Aspects Relating to Part o: Integrated Approach — Prerequisite for Applying
Plumbing Services Provisions of ‘~e Code
including Solid Waste Part 9: Plumbing Services
Management
Section 1 Water Supply, Drainage and Sanitation
(including Solid Waste Management)
Section 2 Gas Supply

The information contained in different groups will essentially serve the concerned professionals dealing in the
respective areas.

( xxii)
CONTENTS

Total Pages

PART O INTEGRATED APPROACH — PREREQUISITE FOR APPLYING PROVISIONS OFTHECODE ... 12

PART 1 DEFINITIONS ... 16

PART 2 ADMINISTRATION ... 24

PART 3 DEVELOPMENTCONTROLRULES ANDGENERALBUILDINGREQUIREMENTS ... 64

PART 4 FIRE ANDLIFE SAFETY ... 88

PART 5 BUILDINGMATERIALS ... 40

PART 6 STRUCTURALDESIGN
Section 1 Loads, Forces and Effects . . . 104
Section 2 Soils and Foundations ... 48
Section 3 Timber and Bamboo
3A Timber . .. 50
3B Barnboo ... 24
Section 4 Masonry ... 44
Section 5 Concrete
5A Plain and Reinforced Concrete .. . 90
5B Prestressed Concrete ... 6
Section 6 Steel ... 8
Section 7 Prefabrication, Systems Building and Mixed/Composite
Construction
7A Prefabricated Concrete ... 22
7B Systems Building and Mixed/Composite Construction ... 12

PART 7 CONSTRUCTIONAL
PRACTICESANDSAFETY ... 70

PART 8 BUILDINGSERVICES
Section 1 Lighting and Ventilation . .. 48
Section 2 Electrical and Allied Installations . . . 68
Section 3 Air Conditioning, Heating and Mechanical Ventilation . . . 48
Section 4 Acoustics, Sound Insulation and Noise Control ... 44
Section 5 Installation of Lifts and Escalators ... 42

PART 9 PLUMBING
SERVICES
Section 1 Water Supply, Drainage and Sanitation (including Solid ... 90
Waste Management)
Section 2 Gas Supply ... 14

PART 10 SIGNSANDOUTDOORDISPLAY STRUCTURES


LANDSCAPING,
Section 1 Landscape Planning and Design ... 30
Section 2 Signs and Outdoor Display Structures ... 24

( xxiii)
-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART O INTEGRATED APPROACH — PREREQUISITE FOR
APPLYING PROVISIONS OF THE CODE

BUREAU OF INDIAN STANDARDS


National Building Code Sectional Committee, CED 46

FOREWORD

In order to provide safe and healthy habitat, careful consideration needs to be paid to the building construction
activity. Building planning, designing and construction activities have developed over the centuries. Large number
of ancient monuments and historical buildings all over the world bear testimony to the growth of civilization
from the prehistoric era with the extensive use of manual labour and simple systems as appropriate to those ages
to the present day mechanized and electronically controlled operations for designing and constructing buildings
and for operating and maintaining systems and services. In those days those buildings were conceptualized and
built by master builders with high levels of artisan skills. Technological and socio-economic developments in
recent times have led to remarkable increase in demand for more and more sophistication in buildings resulting
in ever increasing complexities. These perforce demand high levels of inputs from professionals of different
disciplines such as architecture, civil engineering, structural engineering, functional and life safety services
including special aspects relating to utilities, landscaping, etc in conceptualization, spatial planning, design and
construction of buildings of various material and technology streams, with due regard to various services including
operation, maintenance, repairs and rehabilitation aspects throughout the service life of the building.

This Code, besides prescribing the various provisions, also allows freedom of action to adopt appropriate practices
and provides for building planning, designing and construction for absorbing traditional practices as well as
latest developments in knowledge in the various disciplines as relevant to a building including computer aided
andlor other modern sensors aided activities in the various stages of conceptualization, planning, designing,
constructing, maintaining and repairing the buildings. India being a large country with substantial variations
from region to region, this Code has endeavored to meet the requirements of different regions of the country,
both urban and rural, by taking into consideration factors, such as, climatic and environmental conditions,
geographical terrain, proneness to natural disasters, ecologically appropriate practices, use of eco-friendly materials,
reduction of pollution, protection and improvement of local environment and also socio-economic considerations,
towards the creation of sustainable human settlements.

This Part of the Code dealing with ‘integrated approach’ is being included for the first time. It gives an overall
direction for practical applications of the provisions of different specialized aspects of spatial planning, designing
and construction of buildings, creation of services, and proposes an integrated approach for utilizing appropriate
knowledge and experience of qualified professionals right from the conceptualization through construction and
completion stages of a building project and indeed during the entire life cycle. The ‘integrated approach’ should
not only take care of functional, aesthetic and safety aspects, but alSOthe operational and maintenance requirements.
Also, cost optimization has to be achieved through proper selection of materials, techniques, equipment
installations, etc. Further, value engineering and appropriate management techniques should be applied to achieve
the aim set forth for the purpose of construction of a building fully meeting the specified and implied needs of
spatial functions, safety and durability aspects, life and health safety, comfort, services, etc in the building.

The aim of the ‘integrated approach’ is to get the maximum benefit from the building apd its services in terms of
quality, timely completion and cost-effectiveness. In the team approach which is an essential pre-requisite for
integrated approach, the aim clearly is to maximize the efficiency of the total system through appropriate
optimization of each of its sub-systems. In other words, in the team, the inputs from each of the professional
disciplines have to be so optimized that the total system’s efficiency becomes the maximum. It may be re-
emphasized that maximizing the efficiencies of each sub-system may not necessarily assure the maximization of
the efficiency of the total system. It need hardly to be stated that specified or implied safety will always get
precedence over functional efficiency and economy. Further, progressive approach such as that relating to the
concept of intelligent buildings would be best taken care of by the ‘integrated approach’ as laid down in this Part.

Quality systems approach and certification thereunder covering the various dimensions brought out above may
go a long way in achieving the above goal of real integrated approach.

PART O INTEGRATED APPROACH 3


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART O INTEGRATED APPROACH — PREREQUISITE FOR
APPLYING PROVISIONS OF THE CODE

1 SCOPE development control rules and general building


,, requirements; building materials; fire and life safety;
This Part covers guidelines to be followed for judicious
structural design; constructional practices and safety;
implementation of the provisions of various Parts/
building and plumbing services; and landscaping, signs
Sections of the Code.
and outdoor display structures, other parts/sections of
2 TERMINOLOGY the Code may be referred to.

2.0 For the purpose of this Part, the following 3.2 The scope of various Parts/Sections of the Code
definitions and those given in Part 1 ‘Definitions’ shall which cover detailed provisions on different aspects
apply. of development of land/building construction activity,
are given in Annex A, with a view to providing an
2.1 Authority Having Jurisdiction — The Authority overview for the users of the Code.
which has been created by a statute and which, for the
purpose of administering the Code/Part, may authorize 4 TEAM APPROACH
a committee or an official or an agency to act on its
A land developmentlbuilding project comprises the
behalfj hereinafter called the ‘Authority’.
following major stages:
2.2 Building — Any structure for whatsoever purpose
a) Location/siting,
and of whatsoever materials constructed and every part
thereof whether used as human habitation or not and b) Conceptualization and planning,
includes foundation, plinth, walls, floors, roofs, c) Designing and detailing,
chimneys, plumbing and building services, fixed d) Construction/execution, and
platforms, VERANDAH, balcony, cornice or projection, e) Maintenance and repair.
part of a building or anything affixed thereto or any
wall enclosing or intended to enclose any land or space Each stage necessarily requires professionals of many
and signs and outdoor display structures. Tents/ disciplines who should work together as a well
SHAMIANAHS/PANDALS, tarpaulin shelters, etc, coordinated team to achieve the desired product
erected for temporary and ceremonial occasions shall delivery with quality, in an effective manner.
not be considered as building. Appropriate multi-disciplinary teams need to be
2.3 Owner — Person or body having a legal interest constituted to successfully meet the requirements of
in land and/or building thereon. This includes free different stages. Each team may comprise need based
holders, leaseholders or those holding a sub-lease professionals out of the following depending upon the
which both bestows a legal right to occupation and nature, magnitude and complexity of the project:
gives rise to liabilities in respect of safety or building a) Architect,
condition. b) Civil engineer,
In case of lease or sub-leaseholders, as far as ownership c) Structural engineer,
with respect to the structure is concerned, the structure d) Elec~cal engineer,
of a flat or structure on a plot belongs to the allottee/
e) Plumbing engineer,
lessee till the allotment/lease subsists.
f) Fire protection engineer,
NOTE — For the purpose of the Code, the word ‘owner’ will
g) HVAC engineer,
also cover the generally understood terms like ‘client’, ‘user’,
etc. h) Environment specialist,

3 GENERAL j) Town planner,


k) Urban designer,
3.1 Buildings, shall be classified as Residential,
m) Landscape architect,
Educational, Institutional, Assembly, Business,
Mercantile, Industrial, Storage and Hazardous in n) Security system specialist,
groups and sub-division as classified in Part 4 ‘Fire P) Interior designer,
and Life Safety’. q) Quantity surveyor,
For further sub-classification of buildings and various r) Project/construction manager, and
related provisions thereof with respect to administration; s) Other subject specialist(s).

PART O INTEGRATED APPROACH


4.1 Design Team depending on the size and complexity of the project,
are carefully selected considering their qualification,
In building projects various aspects like form; space
experience and expertise in these fields.
planning; aesthetics; fire and life safety; structural
adequacy; plumbing services; lighting and natural 4.3 Operation and Maintenance Team
ventilation; electrical and allied installations; air
conditioning, heating and mechanical ventilation; Operation, maintenance and repairs also require a
acoustics, sound insulation and noise control; multi-disciplinary approach to ensure that all the
installation of lifts and escalators; building automation; requirements of the users are satisfactorily. met. During
data and voice communication; other utility services maintenance and repairs, the jobs requiring inter-
installations; landscape planning and design; urban disciplinary co-ordination have to be executed in such
planning; etc need to be kept in view right at the a manner as not only to cause least inconvenience to
concept stage. The project requiring such multi- the user but also to ensure that there is no mismatch or
disciplinary inputs need a co-ordinated approach damage to the structure, finishings, fittings and fixtures.
among the professionals for proper integration of For carrying out routine maintenance/repair jobs,
various design inputs, For this, and to take care of the utilization of “the services of trained technicians
complexities of multi-disciplinary requirements, a preferably having multi-disciplinary skills should be
design team of professionals from required disciplines encouraged.
shall be constituted at the appropriate stage. Here, it is Special repairs, rehabilitation and retrofitting are
desirable that the multi-disciplinary integration is specialized jobs which demand knowledge of the
initiated right from the concept stage. The team shall existing structure/installations. Association of
finalize the plan. The composition of the team shall concerne# specialists may be helpful for these works.
depend on the nature and magnitude of the project.
The Operation and Maintenance Team may also be
Design is an evolutionary and participatory process,
known as Asset Management or Estate Management
where participation of owner constitutes a very
Team.
important input at all stages, and the same shall be
ensured by the design team. 5 PLANNING, DESIGNING AND DEVELOPMENT
To ensure proper implementation of the design, the 5.1 The main functions of design team (see 4.1)
design team, may be associated during the constructioti constituted for the planning, designing and development,
execution stage. are as under
4.2 Project Management and Construction a) Formalization of design brief in consultation
Management Teams with the owner.

The objective of project management or construction b) Site investigationhrvey.


management is primarily to achieve accomplishment c) Preparation of alternative concept designs.
of project in accordance with the designs and d) Selection of a concept in consultation with
specifications in a stipulated time and cost framework, and with the consent of owner.
with a degree of assurance prior to commencement and e) Sizing the system.
satisfaction on accomplishment.
f) Development of design, covering :
For large projects, separate teams of experienced 1) Integration of architecture, structure and
professionals from the required disciplines may services,
be constituted for project management and for 2) Synthesis of requirements of each
construction management depending upon the discipline, and
complexities of the project. However, for smaller
3) Interacticm with each other and with the
projects these teams may be combined. The teams shall
owner.
be responsible for day-to-day execution, supervision,
@ Preparation of preliminary designs and
quality control, etc and shall ensure inter-disciplinary
drawings and obtaining owner’s approval,
co-ordination during the construction stage. The team
shall be responsible to achieve satisfactory completion h) Preparation of preliminary cost estimates for
of the project with regard to cost, time and quality. approval of owner,
Some members of the design team may also be j) Preparation of work-breakdown structure and
included in the project management team and/or programme for pre-construction activities.
associated actively during the project execution stage. k) Assisting client to obtain approvals of the
It is important that leaders and members of project Authority.
management/construction management teams, m) Preparation of detailed specification and

6 NATIONALBUILDING CODE OF INDIA


B
construction working drawings with integration 0 Acoustical controls for buildings and the
of engineering inputs of all concerned surroundings.
disciplines. k) Promotion of artwork in buildings, specially
n) Preparation of detailed design of each buildings of importance.
discipline for various services. m) Due cognizance of recommendations of the
P) Peer reviewlproof checking of the drawingsl Archeological Survey of India with regard to
designs in case of important projects, national monuments and construction in
depending upon their complexity and archaeologically important sites.
sensitivity. n) Due cognizance of relevant provisions of
!0 Preparation of detailed cost estimate. applicable coastal zone regulation act.
r) Obtaining final approval of client. P) Conservation of heritage structures and areas.
s) Preparation of bill of quantities, specifications @ Environmental and social impact analysis.
and tender documents. r) Design of services with emphasis on aspects
5.2 The following considerations, as may be of energy efficiency, environment friendliness
applicable to the project, may be considered during and maintainability.
planning, notwithstanding other relevant aspects s) Integrated waste management.
specifically prescribed in concerned parts/sections of t) Voice and data communication, automation
this Code; these considerations in general are with the of building services, and intelligent building;
objective of addressing to the important issues like use of security and surveillance system in
environmental protection, energy conservation, important and sensitive buildings, such as,
cultural issues, creating barrier free built-environment, access control for the people as well as for
safety aspects, etc, all of these leading towards vehicle.
sustainable development, and have to be applied with u) Interlinking of fire alarm system, fire
due regard to the specific requirements of size and type protection system, security system, ventilation,
of project: electrical systems, etc.
a) Geoclimatic, geological and topographical v) Analysis of emergency power, standby power
features. requirement and captive power systems.
b) Varied sociological pattern of living in the w) Cost optimization through techniques like
country. value engineering.
c) Effective land use to cater to the needs of the Y) Adoption of innovative technologies giving
society in a most convenient manner. due consideration to constructability and
d) Modular planning and standardization to quality aspects.
take care of future planning giving due z) Instrumentation of buildings and monitoring
consideration to the specified planning and use of information so generated to effect
controls. improvements in planning and design of
e) Emphasis on daylight utilization, natural future building projects.
ventilation, shielding, and window area
6 CONSTRUCTION/EXECUTION
and its disposition; daylighting to be
(ACTUALIZATION)
supplemented with an integrated design of
artificial lighting. 6.1 The main functions of the teams (see 4.2) ‘)
f-) Optimum utilization of renewable energy constituted for Project Management/Construction
sources duly integrated in the overall energy Management may be, to :
system design; with consideration of active a) specify criteria for selection of constructors;
and passive aspects in building design t
b) specify quality control, quality audit system
including thermal performance of building
and safety system;
envelope.
c) short-list constructors; ~,
g) Rain water harvesting, and use of appropriate
d) have pre-bid meetings with the intending
building materials considering aspects
constructors;
like energy consumption in production,
transportation and utilization, recyclability, e) receive and evaluate tenders;
etc for promoting sustainable development. o select constructors;
h) Requisite mandatory provisions for @ execution and supemision;
handicapped persons. h) monitor quality, time and cost control;

PART O INTEGRATED APPROACH 7


ANNEX A
(Clause 3.2)
BRIEF DETAILS OF THE COVERAGE OF VARIOUS PROVISIONS UNDER
DIFFERENT OTHER PARTS/SECTIONS OF THIS CODE

A-1 PART 1 DEFINITIONS A-6.2 Section 2 Soils and Foundations

It lists the terms appearing in all the Parts/Sections of It covers structural design (principles) of all building
the Code. However, some common definitions are foundations, such as, raft, pile and other foundation
reproduced in this Part also. systems to ensure safety and serviceability without
exceeding the permissible stresses of the materials of
A-2 PART 2 ADMINISTRATION foundations and the bearing capacity of the supporting
It covers the administrative aspects of the Code, such soil.
as applicability of the Code, organization of building
A-6.3 Section 3 Timber and Bamboo
department for enforcement of the Code, procedure
for obtaining development and building permits, and A-6.3.1 Section 3A Timber
responsibility of the owner and all professionals
It covers the use of structural timber in structures or
involved in the planning, design and constructiori of
elements of structures connected together by fasteners/
the building.
fastening techniques.
A-3 PART 3 DEVELOPMENT CONTROL RULES
AND GENERAL BUILDING REQUIREMENTS A-6.3.2 Section 3B Bamboo

It covers the development control rules and general It covers the use of bamboo for constructional purposes
building requirements for proper planning and design in structures or elements of the structure, ensuring
at the layout and building level to ensure health safety, quality and effectiveness of design and construction
public safety and desired quality of life. using bamboo. It covers minimum strength data,
dimensional and grading requirements, seasoning,
A-4 PART 4 FIRE AND LIFE SAFETY preservative treatment, design and jointing techniques
with bamboo which would facilitate scientific
It covers the requirements for fire prevention, life
application and long-term performance of structures.
safety in relation to fire, and fire protection of
It also covers guidelines so as to ensure proper
buildings. The Code specifies planning and
procurement, storage, precautions and design
construction features and fire protection features for
limitations on bamboo.
all occupancies that are necessary to minimize danger
to life and property. A-6.4 Section 4 Masonry

A-5 PART 5 BUILDING MATERIALS It covers die structural design aspects of unreinforced
load bearing and non-load bearing walls, constructed
It covers the requirements of building materials and
using various bricks, stones and blocks permitted in
components, and criteria for accepting new or
accordance with this Section. This, however, also
alternative building materials and components.
covers provisions for design of reinforced brick and
A-6 PART 6 STRUCTURAL DESIGN reinforced brick concrete floors and roofs. It also
covers guidelines regarding earthquake resistance of
This Part through its seven sections provides for low strength masonry buildings.
structural adequacy of buildings to deal with both
internal and external environment, and provide A-6.5 Section 5 Concrete
guidance to engineerslstructural engineers for varied
A-6.5.1 Section 5A Plain and Reinforced Concrete
usage of material/technology types for building
design. It covers the general structural use of plain and
reinforced concrete.
A-6.1 Section 1 Loads, Forces and Effects

It covers basic design loads to be assumed in the design A-6.5.2 Section 5B Prestressed Concrete
of buildings. The live loads, wind loads, seismic loads, It covers the general structural use of prestressed
snow loads and other loads, which are specified therein, concrete. It covers both work carried out on site and
are minimum working loads which should be taken the manufacture of precast prestressed concrete
into consideration for purposes of design. units.

PART O INTEGRATED APPROACH 9


A-6.6 Section 6 Steel A-8.3 Section 3 Air Conditioning, Heating and
Mechanical Ventilation
It covers the use of structural steel in general building
construction including the use of hot rolled steel This Section covers the design, construction and
sections and steel tubes. installation of air conditioning and heating systems and
equipment installed in buildings for the purpose .,
A-6.7 Section 7 Prefabrication, Systems Building of providing and maintaining conditions of air
and Mixed/Composite Construction temperature, humidity, purity and distribution suitable
for the use and occupancy of the space.
A-6.7.1 Section 7A Prefabricated Concrete

It covers recommendations regarding modular A-8.4 Section 4 Acoustics, Sound Insulation and
Noise Control
planning, component sizes, prefabrication systems,
design considerations, joints and manufacture, storage, It covers requirements and guidelines regarding
transport and erection of prefabricated concrete planning against noise, acceptable noise levels and the
elements for use in buildings and such related requirements for sound insulation in buildings with
requirements for prefabricated concrete. different occupancies. ~

A-6.7.2 Section 7B Systems Building and Mixed/ A-8.5 Section 5 Installation of Lifts and
Composite Construction Escalators
It covers recommendations regarding modular It covers the essential requirements for the installation, ~
planning, component sizes, joints, manufacture, operation, maintenance and also inspection of lifts
storage, transport and erection of prefabricated (passenger lifts, goods lifts, hospital lifts, service lifts
elements for use in buildings and such related and dumb-waiter) and escalators so as to ensure safe
requirements for mixed/composite construction. and satisfactory performance.
!
A-7 PART 7 CONSTRUCTIONAL PRACTICES A-9 PART 9 PLUMBING SERVICES
AND SAFETY
This Part through its two sections gives detailed
It covers the constructional planning, management and guidance to concerned pro fessionalslplumbing
practices in buildings; storage, stacking and handling engineers with regard to plumbing and other related
of materials and safety of personnel during construction requirements in buildings.
operations for all elements of a building and demolition
of buildings. It also covers guidelines relating to A-9.1 Section 1 Water Supply, Drainage and
maintenance management, repairs, retrofitting and Sanitation (Including Solid Waste Management)
strengthening of buildings. The objective can be best It covers the basic requirements of water supply for
achieved through proper coordination and working by residential, business and other types of buildings,
the project management and construction management including traffic terminal stations. This Section also
teams. deals with general requirements of plumbing comected
to public water supply and design of water supply
A-8 PART 8 BUILDING SERVICES systems.
This Part through its five elaborate sections on utilities It also covers the design, layout, construction and
provides detailed guidance to concerned professionals/ maintenance of drains for foul water, surface water
utility engineers for meeting necessary functional and sub-soil water and sewage; together with all
requirements in buildings. ancillary works, such as connections, manholes and
inspection chambers uied within the building and from
A-8.1 Section 1 Lighting and Ventilation
building to the connection to a public sewer, private
It covers requirements and methods for lighting and sewer, individual sewage-disposal system, cess-pool,
ventilation of buildings. soakaway or to other approved point of disposal/
treatment work. It also includes the provisions on solid
A-8.2 Section 2 Electrical and Allied Installations waste management.
It covers the essential requirements for electrical and
A-9.2 Section 2 Gas Supply
allied installations in buildings to ensure efficient use
of electricity including safety from fire and shock. This It covers the requirements regarding the safety of persons
Section also includes general requirements relating to and property for all piping uses and for all types of gases
lightning protection of buildings. used for fuel or lighting purposes in buildings.

10 NATIONAL BUILDING CODE OF INDIA


A-10 PART 10 LANDSCAPING, SIGNS AND A-10.2 Section 2 Signs and Outdoor DispIay
OUTDOOR DISPLAY STRUCTURES Structures

A-10.1 Section 1 Landscape Planning and Design It covers the requirements with regard to public safety,
It covers requirements of landscape planning and structural safety and fire safety of all signs and outdoor
design with the view to promoting quality of outdoor display structures including the overall aesthetical
built environment and protection of land and its aspects of imposition of signs and outdoor display
resources. structures in the outdoor built environment.

PART O INTEGRATED APPROACH 11


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 1 DEFINITIONS

BUREAU OF INDIAN STANDARDS


.

I
National Building Code Sectional Committee, CED 46

FOREWORD

Each Part or Section of the National Building Code gives the definitions of the special terms used in it. These
definitions may be found in the clause ‘Terminology’ normally placed immediately after the ‘Scope’ in each
Part/Section. However, users may find this part very convenient for reference as it gives the alphabetically
arranged list of terms defined in all the parts along with the location of the deilnition.

PART 1 DEFINITIONS 3
.

I
r
,’>-
,*.

NATIONAL BUILDING CODE


PART 1 DEFINITIONS

1 SCOPE Atmospheric Pressure — Part 81Section 3


This Part lists the terms appearing in all the Parts/ Audible Frequency Range — Part 81Section 4
Sections of the National Building Code of India. The Authority Having Jurisdiction — Part 2, Part 3,
terms have been arranged in their alphabetical order. Part 6/Section 7B, Part 9/Section 1, Part 9/Section 2,
The Part(s) /Section(s) in which these terms are Part 10/Section 2
appearing, have been indicated against the terms. The Authority which has been created by a statute and
However, some common definitions are reproduced which, for the purpose of administering the Code/Pint,
in this part also; the definitions being placed may authorize a committee or an official or an agency
immediately below the term concerned. to act on its behalfl hereinafter called the ‘Authority’.
Automatic Fire Detection and Alarm System — Part 4
A
Automatic Operation — Part 81Section 5
Abandoned Sign — Part 10/Section 2 Automatic Sprinkler System — Part 4
Access — Part 3 Available Head — Part 9/Section 1
Access Panel — Part 9/Section 1 Avenue — Part 10/Section 1
Accessory — Part 8/Section 2 A-Weighted Sound Pressure Level, LPA — Part 81
Accessoiy Use — Part 2, Part 3 Section 4 ,---

Any use of the premises subordinate to the principal A-Weighted Sound Pressure, pA — Part 8/Section 4
use and customarily incidental to the principal use. Axial Flow Fan — Part 8/Section 1
&...

Advertising Sign — Part 10/Section 2 Azimuth ($) — Part 8/Section 1

Air Change per Hour — Part 8/Section 1 B


Air Conditioning — Part 81Section 3
Back Fill — Part 61Section 2
Air Gap — Part 9/Section 1
Back Siphonage — Part 9/Section 1
Air-l?reak — Part 9/Section 1
Back to Back Cluster — Part 3
Alteration — Part 2, Part 3
Back Up — Part 9/Section 1
A change from one occupancy to another, or a Backfiow Prevention Device — Part 91Section 1
structural change, such as an addition to the area or Backjlow — Part 9/Section 1
height, or the removal of part of a building, or any
Background Noise — Part 8/Section 4
change to the structure, such as the construction of,
cutting into or removal of any wall, partition, column, Balcony — Part 3
beam, joist, floor or other support, or a change to or Baluster — Part 8/Section 5
closing of any required means of ingress or egress or a Balustrade — Part 8/Section 5
change to the fixtures or equipment. Bamboo — Part 61Section 3B
Alternating Current Variable Voltage (ACW) Control Bamboo Borer (Bamboo GHOOIV) — Part 6/Section 3B
— Part 8/Section 5 Bamboo Clump — Part 61Section 3B
... . .
Alternating Current Variable Voltage Variable Bamboo Culm — Part 6LSection 3B
Frequency (A CWVF) Control — Rut 81Section 5 Bamboo Mat Board — Part 6/Sedtion 3B
Altitude (E)) — Part 8/Section 1 Banner — Part 10/Section 2
Ambient Noise — Part 8/Section 4 Banner Sign — Part 10ISection 2
Anatomical Purpose Definitions for Engineers — Barrel — Part 9/Section 1
Part 61Section 3B Base — Part 9/Section 1
Apparatus — Part 8/Section 2 Basement or Cellar — Part 3
Appliance — Part 8/Section 2 Basic Module — Part 6/Section 7A, Part 61Section 7B
Appliance Valve — Part 91Section 2 Basic or Ultimate Stress — Part 61Section 3,
Approved — Part 2, Part 3, Part 10/Section 2 Part 6/Section 3B
Approved by the Authority having jurisdiction. Batter Pile (Raker Pile) — Part 61Section 2
Area of Special Control — Part 10/Section 2 Battery of Fixtures — Part 91Section 1

PART 1 DEFINITIONS 5
Beam — Part 6/Section 3B SHAMIANAHS, tarpaulin shelters, etc, erected for
Beam, Built-Up-Laminated — Part 6/Section 3 temporary and ceremonial occasions with the
Beam, Glued-Laminated — Part 61Section 3 permission of the Authority shall not be considered as
building.
Bearing Capacity, Safe — Part 6/Section 2
Bearing Capacity, Ultimate — Part 61Section 2 Building, Height of — Part 2, Part 3, Part 4
Bearing Pile — Part 61Section 2 The vertical distance measured, in the case of flat roofs
Bearing Pressure, Allowable (Gross or Net) — Part 61 from the average level of the ground around and
Section 2 contiguous to the building or as decided by the
Bearing Pressure, Allowable — Part 61Section 2 Authority to the terrace of last livable floor of the
building adjacent to the external walls; and in the case
Bearing Pressure, Safe — Part 61Section 2
of pitched roofs, up to the point where the external
Bed Block — Part 61Section 4
surface of the outer wall intersects the finished surface
Bedding — Part 91Section 1 of the sloping roof, and in the case of gables facing the
Benching — Part 91Section 1 road, the mid-point between the eaves level and the
Bond — Part 6/Section 4 ridge. Architectural features serving no other function
Bored Cast in-situ Pile — Part 61Section 2 except that of decoration shall be excluded for the
purpose of measuring heights.
Bored Compaction Pile — Part 61Section 2
Bored Pile — Part 61Section 2 Building Line — Part 2, Part 3, Part 10/Section 2
Bottom Car Clearance — Part 81Section 5 The line up to which the plinth of a building adjoining
Bottom Car Runby — Part 81Section 5 a street or an extension of a street or on a future street
Bottom Coutnerweight Runby — Part 81Section 5 may lawfully extend. It includes the lines prescribed,
if any, in any scheme. The building line may change
Boucherie Process — Part 61Section 3B
from time-to-time as decided by the Authority.
Branch — Part 91Section 1
Branch Soil Pipe (BSP) — Part 9Eection 1 Buildings Related Illnesses (BRI) — Part 81Section 3

Branch Soil Waste Pipe (BSWP) — Part 91Section 1 Bunched — Part 8/Section 2

Branch Ventilating Pipe (BVP) — Part 91Section 1 c


Branch Waste Pipe (BWP) — Part 9LSection 1 Cabin — Part 3
Break-in — Part 81Section 4
Cable — Part 8/Section 2
Breaking Strength — Part 61Section 3B Cable Armoured — Part 81Section 2
Break-out — Part 81Section 4 Cable, Crossed Linked Insulated — Part 81Section 2
Brightness Ratio or Contrast — Part 81Section 1
Cable, Flexible — Part 8/Section 2
Broad Band Noise — Part 8fSection 4
Cable, Lead-Covered — Part 81Section 2
Buffer — Part 10/Section 1, Part 8/Section 5 Cable, Metal-Sheathed — Part 81Section 2
Building (House) Drain — Part 9/Section 1
Cable, PVC-Insulated — Part 8/Section 2
Building (House) Drain-Combined — Part 91Section 1
Cable, PVC-Sheathed — Part 81Section 2
Building (House) Drain-Sanita~ — Part 9/Section 1 Cable, Tough Rubber-Sheathed (Cable, TRS) — Part 8/
Building (House) Drain-Stem — Part 91Section 1 Section 2
Building (House) Sewer — Part 9/Section 1 Cable, Weathe~roof — Part 81Section 2
Building (House) Sub-Drain — Part 91Section 1 Cable, XLPE — Part tMSection 2
Building (House) Trap — Part 91Section 1 Call Indicator — Part 81Section 5
Building — Part 2, Part 3, Part 4 Candela (cd) — Part 81Section 1
Any structure for whatsoever purpose and of Canopy — Part 3
whatsoever materials constructed and every part Canopy Sign — Part 10/Section 2
thereof whether used as human habitation or not and Car Bodywork — Part 81Section 5
includes foundation, plinth, walls, floors, roofs,
Car Door Electric Contact — Part 8K3ection 5
chimneys, plumbing and building services, fixed
Car Pla#orm — Part 8/Section 5
platforms, verandah, balcony, cornice or projection,
part of a building or anything affixed thereto or any Car Switch Operation — Part 81Section 5
wall enclosing or intended to enclose any land or space Carframe — Part 81Section 5
and signs and outdoor display structures. Tents/ Carpet Area — Part 3

6 NATIONAL BUILDING CODE OF INDIA


7-

Ceiling Rose — Part 8/Section 2 The material which either burns itself or adds heat to a
Cell — Part 6/Section 3B fire, when tested for non-combustibility in accordance
Cellular Concrete — Part 6/Section 7B, Part 6/ with accepted standard [4(1)].
Section 7A Common Rafier — Part 61Section 3B
Cellulose — Part 6/Section 3B Communication Pipe — Part 91Section 1
Central Field — Part 81Section 1 Components — Part 61Section 7A, Part 6/Section 7B
Centre Internode — Part 6/Section 3B Composite Members — Part 6/Section 7A, Part 6/
Centr@gal Fan — Part 81Section 1 Section 7B
Cesspool — Part 9/Section 1 Compression Wood — Part 61Section 3
Chair — Part 91Section 1 Conductor of a Cable or Core — Part 8/Section 2
Channel — Part 9/Section 1 Conductor, Aerial — Part 8/Section 2
Characteristic Load — Part 61Section 3B Conductor, Bare — Part 8/Section 2
Characteristic Strength — Part 6/Section 3B Conductor, Earthed — Part 81Section 2
Check — Part 6/Section 3 Conductor, Insulated — Part 8/Section 2
CHHAJJA — Part 3 Connection — Part 9/Section 1
Chimney — Part 3 Connector — Part 8/Section 2
Chowk or Courtyard — Part 3 Connector Box or Joint Box — Part 81Section 2
Chowk, Inner — Part 3 Connector for Portable Appliances — Part 8/Section 2
-.
Chowk, Outer — Part 3 Conservation (Preservation) — Part 10/Section 1
Chute — Part 9/Section 1 Consumer — Part 9/Section 1
Circuit — Part 8/Section 2 Consumer’s Pipe — Part 9/Section 1
Circuit Breaker — Part 81Section 2 Consumer’s Terminals — Part 81Section 2
Circuit Final, Sub — Part 8/Section 2 Contaminants — Part 8/Section 1
Cistern — Part 9/Section 1 Contour — Part 10/Section 1
Clay — Part 61Section 2 Contour Interval — Part 10/Section 1
Clay, Firm — Part 61Section 2 Contour Line — Part 10/Section 1
Clay, Soft — Part 61Section 2 Control — Part 8/Section 5
Clay, Stiff — Part 61Section 2 Conventional Symbols — Part 8/Section 2
Cleaning Eye — Part 91Section 1 Conversion — Part 2
Clear Design Sky — Part 8/Section Cooking Alcove — Part 3
Clear Waste Water — Part 91Section 1 Cord, Flexible — Part 8/Section 2
Clearance — Part 8/Section 5 Core of a Cable — Part 8/Section 2
Cleat — Part 8/Section 2 Counterweight — Part 81Section 5
Cleavability — Part 6/Section 3B Cover — Part 91Section 1
Cleavage — Part 6/Section 3B Covered Area — Part 3, Part 4
Climber (CreeperNine) — Part 10ISection 1
Ground area covered by the building immediately
Closed Clusters — Part 3 above the plinth level. The area covered by the
Closed Sign — Part 10/Section 2 following in the open spaces is excluded from covered
Cluster — Part 3 area:
Cluster Court Town House — Part 3 a) garden, rockery, well and well structures,
Cluster Plot — Part 3 plant nursery, waterpool, swimming pool (if
Collapse — Part 61Section 3B uncovered), platform round a tree, tank,
Collection Chamber — Part 91Section 1 fountain, bench, CHABUT~ with open top
and unenclosed on sides by walls and the
Column — Part 61Section 3B
like;
Column, Pier and Buttress — Part 61Section 4
b) drainage culvert, conduit, catch-pit, gully pit,
Columnar — Part 10/Section 1
chamber, gutter and the like;
Combination Sign — Part 10ISection 2 c) compound wall, gate, unstoreyed porch and
Combustible Material — Part 4, Part 10ISection 2 portico, slide, swing, uncovered staircases,

PART 1 DEFINITIONS 7
ramp areas covered by CHHAJJA and the like; Dewpoint Temperature — Part 8/Section 3
and Diameter — Part 9/Section 1
d) watchman’s booth, pumphouse, garbage The nominal internal diameter of pipes and fittings.
shaft, electric cabin or sub-stations, and such Diameter of Knot — Part 61Section 3
other utility structures meant for the services
Diaphragm, Structural — Part 6/Section 3B
of the building under consideration.
Dilution Ventilation — Part 81Section 1
NOTE — For the purpose of this part, covered area
equals the plot area minus the area due for open spaces Direct Earthing System — Part 8/Section 2
in the plot. Direct Solar Illuminance — Part 8/Section 1
Crookedness — Part 61Section 3B Direct Tap — Part 9/Section 1
Cross Wall — Part 6/Section 3B Direction Sign — Part 10/Section 2
Cross-Connection — Part 9/Section 1 Discoloration — Part 6/Section 3, Part 61Section 3B
Cross-Sectional Area of Masonry Unit — Part 61 Discrimination (Over-Current Discrimination) —
Section 4 Part 81Section 2
Cross-Talk — Part 8/Section 4 Distance Area of Resistance Area (for Earth Electrode
Crown of Trap — Part 9/Section 1 only) — Part 81Section 2
‘Cul-de-sac’ Cluster — Part 3 Distribution Board — Part 81Section 2

Curtain Wall — Part 61Section 4 Door — Part 81Section 5

Curvature — Part 61Section 3B Door Closer — Part 81Section 5


Customer’s/Consumer’s Connection — Part 9/ Door Operator — Part 81Section 5
Section 2 Door, Centre Opening Sliding — Part 81Section 5
Cut-off Level — Part 6/Section 2 Door, Mid-Bar Collapsible — Part 81Section 5
Cut-out — Part 8/Section 2 Door, Single Slide — Part 81Section 5
Door, Swing — Part 81Section 5
D
Door, Two Speed Siding — Part 81Section 5
Damp Situation — Part 81Section 2 Door, Vertical Bi-parting — Part 81Section 5
Daylight Area — Part 8/Section 1 Door, Vertical Li@ing — Part 81Section 5
Daylight Factor — Part 8/Section 1 Double Button (Continuous Pressure) Operation —
Daylight Penetration — Part 8/Section 1 Part 8/Section 5
Dead — Part 8/Section 2 Downcomer — Part 4
Dead Knot — Part 6/Section 3 Downtake Tap — Part 91Section 1
Decay or Rot — Part 6/Section 3 Drain — Part 2, Part 3, Part 9/Section 1
Decayed Knot — Part 6/Section 3
A conduit, channel or pipe for the carriage of storm
Decibels — Part 81Section 4 water, sewage, waste water or other water-borne wastes
Deciduous Tree — Part 10/Section 1 in a building drainage system.
Deep Manhole — Part 9/Section 1
Drain Ventilating Pipe (DVP) — Part 91Section 1
Definitions of Defects in Bamboo — Part 61Section 3B
Drainage — Part 2, Part 9/Section 1
Definitions of Defects in Timber — Part 61Section 3
The removal of any liquid by a system constructed for
Deflector Shieve — Part 8/Section 5
the purpose.
Delamination — Part 6/Section 3B
Density — Part 3 Drainage Work — Part 9/Section 1 .
Depth of Manhole — Part 91Section 1 Driven Cast in-situ Pile — Part 6/Section 2
Detached Building — Part 3 Driven Precast Pile — Part 61Section 2

Development — Part 2, Part 3 Drop Connection — Part 9/Section 1


Drop Manhole — Part 91Section 1
‘Development’ with grammatical variations means the
Dry Bulb Temperature — Part 81Section 1
carrying out of building, engineering, mining or other
operations in, or over, or under land or water, or in Dry Riser — Part 4
the use of any building or land, and includes Dry-Bulb Temperature — Part 81Section 3
redevelopment and layout and subdivision of any land; Drying Degrades in Round Bamboo — Part 6/
~d ‘to develop’ shall be construed accordingly. Section 3B

8 NATIONAL BUILDING CODE OF INDIA


Duct System — Part 81Section 3 F
Duration of Load — Part 6/Section 3 Fa~ade Level — Part 81Section 4
Dwelling Uniflenement — Part 3 Factor of Safety (with Respect to Bearing Capacity) —
E Part 61Section 2
Factor of Safety — Part 61Section 2
Earth — Part 81Section 2
Feed Cistern — Part 9/Section 1
Earth Continuity Conductor — Part 81Section 2
Fencing — Part 10/Section 1
Earth Electrode — Part 81Section 2
Finger Joint — Part 61Section 3
Earth Fault — Part 81Section 2
Finished Grade — Part 10/Section 1
Earth Leakage Circuit Breaker System — Part 8/
Fire Damper — Part 81Section 3
Section 2
Fire Door — Part 4
Earthing Lead — Part 81Section 2
Fire Exit — Part 4
Edge Distance — Part 61Section 3
Fire Lift — Part 4
Effective Height — Part 61Section 4
Fire Load — Part 4
Effective Length — Part 61Section 4
Fire Load Density — Part 4
Effective Opening — Part 91Section 1
Fire Resistance Rating — Part 4
Effective Temperature (ET) — Part 81Section 1
Fire Resistance, Criteria of — Part 4
Effective Thickness — Part 61Section 4
Fire Resisting Wall — Part 4
Efficiency of a Pile Group — Part 61Section 2
Fire Separating Wall — Part 4
Egress — Part 10ISection 1
*Fire Separation — Part 3, Part 4
Electric Sign — Part ltYSection 2
Electrical and Mechanical Interlock — Part 81Section 5 The distance in metres measured from the external wall
Electro-Mechanical Lock — Part 81Section 5 of the building concerned to the external wall of any
other building on the site, or from other site, or from
Electronic Devices — Part 81Section 5
the opposite side of street or other public space to the
Elevation — Part 10ISection 1
building for the purpose of preventing the spread of
Emergency Lighting — Part 4 fire.
Emergency Lighting System — Part 4
Fire Separation Wall — Part 8/Section 3
Emergency Stop Push or Switch — Part 81Section 5
Fire Stop — Part 4
Enclosed Distribution Board — Part 81Section 2
Fire Survival Cable — Part 81Section 2
End Distance — Part 61Section 3, Part 61Section 313
Fire Tower — Part 4
End Splitting — Part 61Section 3B
Fitting, Lighting — Part 81Section 2
Enthalphy — Part 81Section 3
Fittings — Part 9/Section 1
Equivalent Continuous A — Weighted Sound Pressure
Level, L~e~,~— Part 81Section 4 Fittings shall mean coupling, flange, branch, bend, tees,
Equivalent Sound Absorption Area of a Room, A — elbows, unions, waste with plug, P or S trap with vent,
Part 8/Section 4 stop ferrule, stop tap, bib tap, pillar tap, globe tap, ball
valve, cistern storage tanlG baths, water-closets, boiler,
Escalator — Part 81Section 5
geyser, pumping set with motor and accessories, meter,
Escalator Installation — Part 81Section 5
hydrant, valve and any other article used in connection
Escalator Machine — Part 81Section 5 with water supply, drainage’ and sanitation.
E.vcape Lighting — Part 4
Fixture Unit — Pat 9/Section 1
Evaporative Air Cooling — Part 81Section 3
Fixture Unit Drainage — Part 91Section 1
Evergreen — Part 10/Section 1
Flame Retardant Cable — Part 81Section 2
Exhaust of Air — Part 81Section 1
Flameproof Enclosure — Part 81Section 2
Exit — Part 3
Flatten Bamboo — Part 61Section 3B
Exotic — Part 10/Section 1
Float Operated Valve — Part 91Section 1
Exposed Metal — Part 81Section 2
Floor — Part 3
Exterior Sign — Part 10/Section 2
External Faces of Cluster — Part 3
External Re@ected Component (ERC) — Part 8/Section 1 * Definitions sre different.

PART 1 DEFINITIONS
The lower surface in a storey on which one normally Ground Sign — Part 10/Section 2
walks in a building. The general term ‘floor’ unless Groundcover — Part 10/Section 1
specifically mentioned otherwise shall not refer to a Group Automatic Operation — Part 81Section 5
‘mezzanine floor’.
Group Housing — Part 3
Floor Area Ratio (FAR,) — Part 3, Part 4 Group Open Space — Part 3
The quotient obtained by dividing the total covered Grout — Part 61Section 4
area (plinth area) on all floors by the area of the plot: Guide Rails — Part 8/Section 5
Guide Rails Fixing — Part 8/Section 5
Total covered area of all floors
FAR = Guide Rails Shoe — Part 81Section 5,
Plot area
Gully Chamber — Part 91Section 1
Floor Levelling Switch — Part 8/Section 5
Gully Trap — Part 91Section 1
Floor Selector — Part S/Section 5
Floor Stopping Switch — Part 8/Section 5 H
Flushing Cistern — Part 9/Section 1 Habitable Room — Part 3
Foliage — Part 10/Section 1 Hard Lundscape — Part 10/Section 1
Footing — Part 61Section 2 Hardy Plant — Part 10/Section 1
Formation — Part 9/Section 1 Harmonics — Part 8/Section 2
Foundation — Part 61Section 2 Haunching — Part 9/Section 1
Foundation, Raft — Part 61Section 2 Hedge — Part 10/Section 1
Free-Field Level — Part 8L3ection 4 Heel Rest Bend or Duck-Foot Bend — Part 91Section 1
Freestanding Sign — Part 10/Section 2 Hemi Cellulose — Part 6&ctiori 3B
French Drain or Rubble Drain — Part 91Section 1 Herb — Part 10/Section 1
Frequency — Part 81Section 4 High Altitudes — Part 91Section 1
Fresh Air or Outside Air — Part 8/Section 1 High Rise Building — Part 4
Frost Line — Part 9/Section 1 Highway Authority — Pm 9kkctioII 1
Full Culm — Part 6Nection 3B Hollow Unit — Part 6/Section 4
Fuse — Part 8/Section 2 Horizontal Exit — Part 4
Fuse-Element — Part 8LSection 2 Horizontal Pipe — Part 9/Section 1
Hospital Lift — Part 81Section 5
G
Hot Water Tank — Part 91Section 1
Gallery — Part 3
Humidification — Part 8/Section 1
Garage, Private — Part 3
Humidity, Absolute — Part 81Section 1
Garage, Public — Part 3
Humidity, Relative — Part 8/Section 1
Gas Fitter — Part 91Section 2
Hydronic Systems — Part 8/Section 3
Geared Machine — Part 8L3ection 5
Gearless Machine — Part 81Section 5 I
General — Part 61Section 2, Part 10/Section 2 Identification Sign — Part 10/Section 2
General Ventilation — Part 81Section 1 Illuminance — Part 8/Section 1
General Washing Place — Part 91Section 1 Illuminated Sign — Part 10/Section 2
Geyser — Part 9/Section 1 Impact Sound Pressure Level, Li — Part 81Section 4
Glare — Part 8/Section 1 Increments — Part 61Section 7A, Part 6/Section 7B
Global Warming Potential (GWP) — Part 8/Section 3 Independent Cluster — Part 3
Globe Temperature — Part 81Section 1 Indoor Air Quality (IAQ) — Part 8/Section 3
Goods Lift — Part 81Section 5 Indoor Ambient Noise — Part 8/Section 4
Grade — Part 10/Section 1 Injlammuble — Part 81Section 2
Gradient — Part 10/Section 1 Informational Sign — Part 10/Section 2
Grading — Part 10/Section 1 Ingress — Part 10/Section 1
Grasses — Part 10/Section 1 Inlet Hopper — Part 91Section 1
Gravel — Part 6/Section 2 Inner Diameter — Part 61Section 3B

10 NATIONAL BUILDING CODE OF INDIA


Insertion Loss (&) — Part 8/Section 4 Levelling Zone — Part 81Section 5
Inside Location — Part 6/Section 3, Part 61Section 3B Licensed Plumber — Part 91Section 1
Inspection Chamber — Part 91Section 1 Liji — Part 3, Part 8/Section 5
Installation (Electrical), of Buildings — Part 8/ An appliance designed to transport persons or materials
Section 2 between two or more levels in a vertical or substantially
Insulated — Part 8/Section 2 vertical direction by means of a guided car platform.
Insulation (Electrical) — Part 81Section 2
Lijl Car — Part 8/Section 5
Insulation, Basic — Part 81Section 2
Lcfi Landing — Part 8/Section 5
Insulation, Double — Part 8/Section 2
Lift Machine — Part 8/Section 5
Insulation, Reinforced — Part 8/Section 2
Lift Pit — Part 8/Section 5
Insulation, Supplementary — Part 8/Section 2
Lifi Well — Part 8/Section 5
Interceptor — Part 9/Section 1
Lljl Well Enclosure — Part 8/Section 5
Interceptor Manhole or Interceptor Chamber — Part 9/
Li$ting Beam — Part 81Section 5
Section 1
Light Output Ratio (q) — Part 8/Section 1
Interlocking Cluster — Part 3
Lighting — Part 8/Section 1
Internal Faces of Cluster — Part 3
Lignin — Part 6/Section 3B
Internal Reflected Component (IRC) — Part 8/
Section 1 Linked Switch — Part 81Section 2

Invert — Part 9K3ection 1. Part 10/Section 1 Live Knot — Part 61Section 3


Live or Alive — Part 81Section 2
J Load Bearing Wall — Part 61Section 4
Joint — Part 6/Section 3B, Part 6/Section 4 Loaded Edge Distance — Part 61Section 3
Joist — Part 6/Section 3B Loaded End or Compression End Distance — Part 6/
Junction Pipe — Part 9/Section 1 Section 3B
Local Exhaust Ventilation — Part 81Section 1
K
Location — Part 6/Section 3
Kerb — Part 10/Section 1 Locations, Industrial — Part 8/Section 2
Kerb-Stone — Part 10/Section 1 Locations, Non-Industrial — Part 81Section 2
Knot — Part 61Section 3
Loft -Part3
Knot Hole — Part 6/Section 3 hose Grain (Loosened Grain) — Part 61Section 3
L Loose Knot — Part 61Section 3
Lumen (lm) — Part 8/Section 1
Lagging — Part 9/Section 1
Luminance (At a Point of a Surface in a Given
Luminated Veneer Lumber — Part 61Section 3
Direction) (Brightness) — Part 81Section 1
Landing — Part 8/Section 5
Luminous Flux (@)— Part 8/Section 1
Landing Call Push — Part 8/Section 5
I-unding Door — Part 8/Section 5 M
Lunding Zone — Part 81Section 5
Main Soil Pipe (MSP) — Part 91Section 1
Luteral Support — Part 61Section 4
Main Soil Waste Pipe (MSWP) — Part 91Section 1
Leaf — Part 61Section 4
Main Ventilating Pipe (MVP) — Part 9/Section 1
Ledge or TAND — Part 3
Main Waste Pipe (MWP) — Part 91Section 1
Length of Internode — Part 6/Section 3B
Maintenance Factor (d) — Part 8/Section 1
Levelling Device, Lift Car — Part 81Section 5
Make-up Air — Part 8/Section 1
Levelling Device, One-Way Automatic — Part 81
Make-up Ground — Part 61Section 2
Section 5
Manhole — Part 9/Section 1
Levelling Device, Two- Way Automatic Non-Maintaining
— Part 81Section 5 Manhole Chamber — Part 9/Section 1

Levelling Device, Two-Way Automatic Maintaining — Mansard — Part 10/Section 2


Part 8/Section 5 Marquee Sign — Part 10/Section 2
Levelling Devices — Part 8/Section 5 Masonry — Part 6/Section 4

PART 1 DEFINITIONS 11
Masonry Unit — Part 6/Section 4 *Offset — Part 6/Section 2, Part 9/Section 1
Matchet — Part 6/Section 3B Oil Iih@er — Part 8/Section 5
Mats — Part 6Nection 3B Oil Bufier Stroke — Part 8/Section 5
Means of Egress — Part 4 Open Clusters — Part 3
Mechanical Ventilation — Part 8/Section 1 Open Sign — Part 10/Section 2
Meridian — Part 8/Section 1 Open Space — Part 3
Mezzanine Floor — Part 3 Open Space, Front — Part 3
Miniature Circuit Breaker — Part 8/Section 2 Open Space, Rear — Part 3
Modular Co-ordination — Part 6/Section 7A, Part 6/ Open Space, Side — Part 3
Section 7B Operating Device — Part 8/Section 5
Modular Grid — Part 6/Section 7A, Part 6/Section 7B Operation — Part 8/Section 5
Module — Part 6/Section 7A, Part 6L3ection 7B Operational Constructiotilnstalt!ation — Part 2
Mortise and Tenon — Part 6/Section 3B Orientatwn of Buildings — Part 8/Section 1
Mould — Part 61Section 3 Outdoor Furniture — Part 10/Section 1
Mound — Part 10/Section 1 Outer Diameter — Part 6/Section 3B
Mtdtimodule — Part 61Section 7A, Part 6fSection 7B Outside Location — Part 61Section 3A, Part 6/
Multiple Earthed Neutral System — Part 8/Section 2 Section 3B
i?lulti-Under-Reamed Pile — Part 61Section 2 Over Speed Governor — Part 8/Section 5
Overhead Beams — Part 81Section 5
N
Owner — Part 2, Part 3, Part 10/Section 2
Native — Part 10/Section 1
Person or body having a legal interest in land and/or
Natural Grade — Part 10/Section 1
building thereon. This includes free holders,
Natural Ventilation — Part 8/Section 1 leaseholders or those holding a sub-lease which both
Negative Skin Friction — Part 61Section 2 bestows a legal right to occupation and gives rise to
,Net Section — Part 61Section 3B liabilities in respect of safety or building condition.
Neutral Conductor — Part 8/Section 2 In case of lease or sub-leaseholders, as far as ownership
Node — Part 6/Section 3B with respect to the structure is concerned, the structure
Noise — Part 8/Section 4 of a flat or structure on a plot belongs to the allottee/
Noise Exposure Forecast (NEF) — Part 81Section 4 lessee till the allotment/lease subsists.

Noise Rating (NR) — Part 8/Section 4 Ozone Depletion Potential (ODP) — Part 81Section 3
Noise Reduction Co-efficient (NRC) — Part 8/
P
Section 4
Non-Selective Collective Automatic Operation — Panel Wall — Part 61Section 4
Part 8L3ection 5 Parapet — Part 3, Pall 10ISection 2
Non-Service Laterine — Part 9/Section 1 Parking Space — Part 3
Normalized Impact Sound Pressure Level, L. — Part 8/ Partition — Part 3
Section 4 Partition Wall — Part 61Section 4
North and South Points — Pm 8/Section I Passenger Lift — Part 8LSection 5
0 Peat — Part 61Section 2
Percentile Level, L~~ ~ — Pm 81Section 4
Occupancy or Use Group — Part 2, Part 3, Part 4
Period of Supply — Part 91Section 1
The principal occupancy for which a building or a Peripheral Field — Part 81Section 1
part of a building is used or intended to be used; for
Permanent Load — Part 6/Section 2
the purposes of classification of a building according
Permissible Stress — Part 61Section 3, Part 6/
to occupancy, an occupancy shall be deemed to
Section 3B
include the subsidiary occupancies which are
contingent upon it. Permit — Part 2
Pile Foundation — Part 6/Section 2
Occupier — Part 2
Octave Band — Part 8/Section 4 * Definitions are different.

12 NATIONAL BUILDING CODE OF INDIA


Pilot — Part 91Section 2 Rating Level, LA,, T, — Part 8/Section 4
Pink Noise — Part 8/Section 4 Recirculated Air — Part 81Section 3
Pipe System — Part 9/Section 1 Rejlected Glare — Part 81Section 1
Pipe Work — Part 9/Section 1 Reflection Factor (Reflectance) — Part 81Section 1
Pitch Pocket — Part 61Section 3 Refrigerant — Part 81Section 3
Plenum — Part 81Section 3 Registered Architect, Engineer, Structural Engineer,
Plinth — Part 3 Supervisor, Town Planner — Part 2
Regulatory Sign — Part 10ISection 2
The portion of a structure between the surface of
Relative Humidi@ — Part 81Section 3
the surrounding ground and surface of the floor,
immediately above the ground. Residual Current Circuit Breaker — Part 81Section 2
Residual Head — Part 91Section 1
Plinth Area — Part 3, Part 4
Retiring Cam — Part 81Section 5
The built up covered area measured at the floor level Return Air — Part 81Section 3
of the basement or of any storey.
Reveal — Part 81Section 1
Plug — Part 8/Section 2 Reverberation Time, T — Part 81Section 4
Plumbing System — Part 91Section 1 Rheostatic Control — Part 81Section 5
Plumbing — Part 9/Section 1 Riser — Part 9LSection 2
Point (in Wiring) — Part 8/Section 2 Road — Part 2, Part 3
Porch — Part 3 Road Line — Part 2, Part 3
Portable Sign — Part 10/Section 2 Roof Battens — Part 6/Section 3B
Position an&or Direction Indicator — Part 81Section 5 Roof Exits — Part 4
Positive Ventilation — Part 8/Section 1, Part 8/ Roof Sign — Part 10/Section 2
Section 3 Roof Skeleton — Part 61Section 3B
Potable Water — Part 91Section 1 Room Height — Part 2, Part 3
Prefabricate — Part 6/Section 7 A, Part 61Section 7B
The vertical distance measured from the finished floor
Prefabricated Building — Part 61Section 7A, Part 6/
surface to the finished ceiling surface. Where a finished
Section 7B
ceiling is not provided, the underside of the joists or
Premises — Part 9/Section 1 beams or tie beams shall determine the upper point of
Pressure Regulator — Part 91Section 2 measurement for determining the head room.
Pressurization — Part 4 Room Index (k, ) — Part 8/Section 1
Pressurization Level — Part 4 Roping Multiple — Part 8/Section 5
Principal Ra@er — Part 6/Section 3B Row Housing/Row Type Building — Part 3
Projecting Sign — Part 10/Section 2
Propeller Fan — Part 8/Section 1 s
Psychometric Chart — Part 8/Section 3 Saddle — Part 9/Section 1
Psychrornetry — Part 8/Section 3 Safety Gear — Part 81Section 5
Puff Ventilation — Part 9/Section 1 Sanctioned Plan — Part 2
Pure Tone — Part 8/Section 4 Sand — Part 6/Section 2
Purge — Part 9/Section 2 Sand, Coarse — Part 61Section 2
Purlins — Part 6/Section 3B Sand, Fine — Part 61Section 2
Sand, Medium — Part 61Section 2
Q Sandwich Panels — Part 61Section 7A, Part 61
Quahjied Installing Agency — Part 91Section 2 Section 7B
Sandwich, Structural — Part 61Section 3
R Sanitary Appliances — Part 9/Section 1
Rated Load (Escalator) — Part 8/Section 5 Sap Stain — Part 61Section 3
Rated Load — Part 81Section 5 Sapwood — Part 6/Section 3
Rated Speed (Escalator) — Part 8/Section 5 Sca#old — Part 6/Section 3B
Rated Speed — Part 8LSection 5 Screen — Part 10ISection 1

PART 1 DEFINITIONS 13
Sediment — Part 10/Section 1 Slenderness Ratio — Past 61Section 4
Selective Collective Automatic Operation -Part81 Sliver — Part 6/Section 3B
Section 5 Slop Hopper (Slop Sink) — Part 9/Section 1
Self Compacting Concrete — Part 6/Section 7A, Part 6/ Slope of Grain — Part 61Section 3
Section 7B Smoke Damper — Part 81Section 3
Semi-Detached Building — Part 3 Soakaway — Part 9/Section 1
Service — Part 8/Section 2 Socket-Outlet — Part 81Section 2
Service Laterine — Part 91Section 1
Soffit (Crown) — Part 91Section 1
Service L@ (Dumb-Waiter) — Part 81Section 5
Soft Lundscape — Part 10ISection 1
* Service Pipe — Part 9/Section 1, Part 9/Section 2
Soft Rock — Part 61Section 2
Service Road — Part 2, Part 3
Soil Appliances — Part 91Section 1
Service Shut-Off Valve (Isolation Valve) — Part 91
Soil Pipe — Part 91Section 1
Section 2
Soil Waste — Part 91Section 1
Set-back Line — Part 2, Part 3
Soil, Black Cotton — Part 61Section 2
A line usually parallel to the plot boundaries and laid Soil, Coarse Grained — Part 61Section 2
down in each case by the Authority, beyond which
Soil, Find Grained — Part 61Section 2
nothing can be constructed towards the site boundaries.
Solar LAad — Part 813ection 1
Sewer — Part 9/Section 1 Solid-State d.c. Variable Voltage Control- Part 81
Shade Factor — Part 8/Section 3 Section 5
Shake — Part 61Section 3 Sound — Part 81Section 4
Shallow Foundation — Part 6/Section 2 Sound Exposure Level, Lm — Part 81Section 4
Shear Connectors — Part 6/Section 7A, Part 6/ Sound Knot — Part 61Section 3
Section 7B Sound Power — Part 8LSection 4
Shear Wall — Part 6/Section 4 Sound Power Level (LW) — Part 81Section 4
Sheave — Part 8/Section 5 Sound Pressure Level, LP — Part 81Section 4
Shrub — Part 10/Section 1 Sound Pressure, p — Part 81Section 4
Sick Building Syndrome (SBS) — Part 8/Section 3 Sound Receiver — Part 81Section 4
Sign — Part 10/Section 2 Sound Reduction Index, R — Part 81Section 4
Sign Area — Part 10/Section 2 Sound Source — Part 81Section 4
Sign Copy — Part 10/Section 2 Spaced Column — Part 61Section 3
Sign Face — Part 10/Section 2 Spectrum — Part 8/Section 4
Sign Structure — Part 10/Section 2 Speech Inte~erence Level (SIL) — Part 81Section 4
Signal Operation — Part 81Section 5 Split — Part 61Section 3
Signs — Part 10/Section 2 Splits — Part 6/Section 3B
Silt — Part 6/Section 2 Spot Elevation — Part 10/Section 1
Single Automatic Operation — Part 8/Section 5 Spray-Head System — Part 8/Section 1
Single-Speed Alternating Current Control — Part 81 Spread Foundation — Part 6/Section 2
Section 5
Spring Bujfer — Part W3ection 5
Site (Plot) — Part 2, Part 3, Part 4
Spring Bu~er Load Rating — Part 8/Section 5
A parcel (piece) of land enclosed by definite boundaries.
Spring Bufler Stroke — Part 8/Section 5
Site, Comer — Part 3
Stack E#ect — Part 8/Section 1
Site, Depth of — Part 3
Stack Pressure — Part 4
Site, Double Frontage — Part 3
Staircover (or Mumty) — Part 3
Site, Interior or Tandem — Part 3
Standardized Impact Sound Pressure Level, J!..n~—
Sky Component (SC) — Paxt 8/Section 1 Part 81Section 4
Sky Sign — Part 10/Section 2
Standardized Level D@erence, D,~ — Part 8/Section 4
Slack Rope Switch — Part 81Section 5
Static Pressure — Part 8/Section 3
* Definitions are &lfferent. Stop Tap — Part 9/Section 1

14 NATIONAL BUILDING CODE OF INDIA


Stop-Cock — Part 9/Section 1 Swale — Part 10/Section 1
Storage Tank — Part 9/Section 1 Switch — Part 8/Section 2
Storey — Part 3 Switch Disconnector Fuse — Part 8/Section 2

The portion of a building included between the surface Switch Disconnectors — Part 81Section 2
of any floor and the surface of the floor next above it, Switchboard — Part 81Section 2
or if there be no floor above it, then the space between Switchgear — Part 8/Section 2
any floor and the ceiling next above it. System — Part 6/Section 7A, Part 6/Section 7B,
Storey, Topmost — Part 3 Systems of Drainage — Part 9/Section 1
Street — Part 2, Part 3 T
Any means of access, namely, highway, street, lane, Taper — Part 6/Section 3B
pathway, alley, stairway, passageway, carriageway, Temporary Sign — Part 10/Section 2
footway, square, place or bridge, whether a
Terminal Slow Down Switch — Part 8/Section 5
thoroughfare or not, over which the public have a right
Terminal Stopping Device Final — Part 8/Section 5
of passage or access or have passed and had access
unintemuptedly for a specified period, whether existing Terminal Stopping Switch Normal — Part 81Section 5
or proposed in any scheme and includes all bunds, Termites — Part 61Section 3
channels, ditches, storm-water drains, culverts, Thermal Energy Storage — Part 8fSection 3
sidewalks, traffic islands, roadside trees and hedges, Thermal Transmittance — Part 81Section 3
retaining walls, fences, barriers and railings within the
Third Octave Band — Part 81Section 4
street lines.
Threshold Limit Value (TLV) — Part 81Section 1
Street Furniture — Part 10/Section 1 Threshold of Hearing — Part 81Section 4
Street Level or Grade — Part 2, Part 3 Tight Knot — Part 61Section 3
The officially established elevation or grade of the Tissue — Part 6/Section 3B
centre line of the street upon which a plot fronts and if To Abut — Part 3
there is no officially established grade, the existing To Erect — Part 2, Part 3
grade of the street at its mid-point.
Top Car Clearance — Part 81Section 5
Street Line — Part 2, Part 3, Part 10/Section 2 Top Counterweight Clearance — Part 8/Section 5
The line defining the side limits of a street. Topsoil — Part 10/Section 1
Tot Lot — Part 10/Section 1
Structural Element — Part 61Section 3
Total Headroom — Part 8/Section 5
Structural Grades — Part 61Section 3
Total Settlement — Part 61Section 2
Structural Purpose Definitions — Part 61Section 3,
Tower-like Structures — Part 3
Part 6/Section 3B
Trade Efluent — Part 91Section 1
Structural Timber — Part 61Section 3
Transient Sound — Part 8/Section 4
Structure Borne Noise — Part 81Section 4
Transplanting — Part 10/Section 1
Structure, Permanent — Part 6fSection 3
Trap — Part 9/Section 1
Structure, Temporary — Part 61Section 3
Travel — Part 8/Section 5
Sub-Soil Water — Part 91Section 1
Travel Distance — Part 4
Sub-Soil Water Drain — Part 91Section 1
Tree — Part 10/Section 1
Sub-Zero Temperature Regions — Part 91Section 1
Tree Grate — Part 10/Section 1
Supply Air — Part 81Section 3
Tree/Plant Guard — Part 10/Section 1
Supply and Return Air Grilles and Diffusers — Part 8/
Section 3 Tropical Summer Index (TSI) — Part 8/Section 1

Supply Pipe — Part 91Section 1 Two-Speed Alternating Current Control — Part 8/~
Section 5
Supports — Part 9/Section 1
Types of Walls — Part 6/Section 4
Su#ace Cracking — Part 61Section 3B
Su~ace Water — Part 9/Section 1 u
Su~ace Water Drain — Part 9/Section 1 Ultimate Load Capacity — Part 61Section 2
Suspension Ropes — Part 81Section 5 Under-Reamed Pile — Part 61Section 2

PART 1 DEFINITIONS 15
Unit — Part 6/Section 7A, Part 61Section 7B Warp — Part 6/Section 3
Unloaded End Distance — Part 61Section 3B Wash-Out Valve — Part 91Section 1
Unsafe Building — Part 2 Waste Appliance — Part 91Section 1
Usable Wall Space — Part 81Section 2 Waste Pipe — Part 9/Section 1
Utilization Factor (Coefficient of Utilizaiton) (p) — Waste- Water (Sullage) — Part 9/Section 1
Part 8/Section 1 Water Conditioning — Part 8/Section 3
Water Hardness — Part 81Section 3
v
Water Main (Street Main) — Part 9/Section 1
Variable Voltage Motor Control (Generator Field
Water Outlet — Part 91Section 1
Control) — Part 81Section 5
Water Seal — Part 91Section 1
Veloci@, Capture — Part 81Section 1
Water Supply System — Part 9/Section 1
Vent Pipe — Part 91Section 2
Water-Closet (WC) — Part 3
Vent StacWVent Pipe — Part 91Section 1
Waterworks — Part 9/Section 1
Vent System — Part 91Section 1
Wavelength — Part 81Section 4
Ventilation — Part 4, Part 8/Section 1
WeatheWroof — Part 8/Section 2
Venting Fire — Part 4
Weighted Level Difference, DW — Part 81Section 4
Verandah — Part 3
Weighted Normalized Impact Sound Pressure tivel,
Verandah Sign — Part 10/Section 2
~... — Part 8/Section 4
Vertical Pipe — Part 91Section 1
Weighted Sound Reduction Index, RW — Part 8/
Vibration Isolation — Part 81Section 4 Section 4
Visual Field — Part 81Section 1 Weighted Standardized Impact Sound Pressure Level,
Voltage Extra Low — Part 8/Section 2 ~“~,~ — Part 8/Section 4
Voltage Extra High — Part 8/Section 2 Weighted Standardized Level Difference, D. TW—
Voltage, High — Part 81Section 2 Part 81Section 4
Voltage, Low — Part 8/Section 2 * Wet Bulb Temperature — Part 8/Section 1, Part 8/
Voltage, Medium — Part 81Section 2 Section 3
Volume to Plot Area Ratio (VPR) — Part 3, Part 4 Wet Location — Part 6/Section 3, Part 61Section 3B
Wet Riser — Part 4
The ratio of volume of building measured in cubic
metres to the area of the plot measured in square metres White Noise — Part 81Section 4
and expressed in metres. Window — Part 3
Window Sign — Part 10ISection 2
w Working Plane — Part 8/Section 1
Wall Sign — Part 10/Section 2 Worm Holes — Part 61Section 3
Wall Thickness — Part 6/Section 3B Wrinkled and Deformed Su~ace — Part 6/Section 3B
Wane — Part 6/Section 3
Warning Pipe — Part 9/Section 1 * Definitions are different.

16 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 2 ADMINISTRATION

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

SECTION1 GENERAL

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 APPLICABILITY OF THE CODE ... 6
4 INTERPRETATION ... 7
5 ALTERNATIVE MATERIALS, METHODS OF DESIGN AND ... 7
CONSTRUCTION, AND TESTS

SECTION 2 ORGANIZATION AND ENFORCEMENT

6 DEPARTMENT OF BUILDINGS ... 7


7 POWER AND DUTIES OF TEAM OF BUILDING OFFICIALS ... 8
8 BOARD OF APPEALS ... 9
9 VIOLATIONS AND PENALTIES ... 9
10 POWER TO MAKE RULES ... 9

SECTION 3 PERMIT AND INSPECTION

11 DEVELOPMENT/BUILDING PERMIT ... 9


12 APPLICATION FOR DEVELOPMENT/BUILDING PERMIT ... 10
13 RESPONSIBILITIES AND DUTIES OF THE OWNER ... 15
14 INSPECTION, OCCUPANCY PERMIT AND POST-OCCUPANCY ... 15
INSPECTION
15 UNSAFE BUILDING ... 16
16 DEMOLITION OF BUILDING ... 16
17 VALIDITY ... 17
18 ARCHITECTURAL CONTROL ... 17

ANNEX A GUIDE FOR THE QUALIFICATIONS AND COMPETENCE OF ... 18


PROFESSIONALS
ANNEX B FORM FOR FIRST APPLICATION TO DEVELOP, ERECT, ... 20
RE-ERECT OR TO MAKE ALTERATION IN ANY PLACE IN A
BUILDING
ANNEX C FORM FOR CERTIFICATE FOR STRUCTURAL DESIGN ... 21
SUFFICIENCY
ANNEX D FORM FOR SUPERVISION ... 21
ANNEX E FORM FOR SANCTION OR REFUSAL OF DEVELOPMENT/ ... 22
BUILDING PERMIT
ANNEX F FORM FOR NOTICE FOR COMMENCEMENT ... 22
ANNEX G FORM FOR CERTIFICATE FOR EXECUTION OF WORK AS ... 23
PER STRUCTURAL SAFETY REQUIREMENTS
ANNEX H FORM FOR COMPLETION CERTIFICATE ... 23
ANNEX J FORM FOR OCCUPANCY PERMIT ... 24

2 NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

A need for codifying and unifying administrative provisions in different development control rules and building
byelaws had been felt, particularly in regard to the applicability of the Code, desirable qualifications for the enforcing
Authority and the representative of the owner and responsibilities and duties of the Authority and the owner.

It is expected that the town and country planning department will co-ordinate the administrative provisions of
this Part and the same given in the State Town and Country Planning Acts.
This Part recommends the setting up of a ‘Board of Appeal’. The ‘Board of Appeal’ gives the owner/architect/
engineer an opportunity to defend the schemes which are based on conventional or new methods of design and
construction or using new materials, which have been otherwise rejected by the Authority.
This Part also emphasizes the need for setting up an Arts Commission for metropolitan areas to safeguard existing
aesthetics in the event of new schemes proposed for buildings of public importance or buildings coming up in an
important area near historic/monumental buildings. The Commission can assist the civic authorities in reviewing
plans for development from the stand point of assuring good taste and regard for often threatened natural beauties.
The Commission can serve as a means whereby by the government and public bodies and individuals could get
advice on artistic questions in connection with building schemes.
The first version of this Part was brought out in 1970, which was subsequently revised in 1983. As a result of
implementing 1970 version of this Part in rewriting building byelaws and development control rules of some
municipal corporations and municipalities, some useful suggestions were emerged. These were incorporated in
the first revision to the extent possible. The significant changes in 1983 version of this Part included the new
administrative provisions related to development control rules, additional information to be fumishedlindicated
in the building plan for multi-storeyed and special buildings and modified provisions regarding submission of
building plans by Government Departments to the Authority.

In this second revision, number of modifications have been incorporated based on the experience gained over the
years specially in view of different techno-administrative and techno-legal regime encountered in various situations
faced. Specially the provisions of this Part have been thoroughly reviewed in the context of the natural calamities
faced by the country, such as the devastating eafihquake in Gujarat in the year 2001, and provisions have been
accordingly modified to further ensure structural adequacy of the buildings. In this context, structural design of
buildings in accordance with the provisions of the Code and construction and supervision thereof by competent
professionals to ensure structural safety have been given due importance in this revision. Other significant
modifications incorporated include:
a) Modifications in the definitions of certain terms;
b) Inclusion of the concept of team of building officials;
c) Inclusion of provision of single window approach for permit for all services;
d) Inclusion of provisions regarding computerization of approval processes for building permits;
e) Inclusion of provision to certify safety of buildings against natural disaster by engineer/structural engineer
and owner;
0 Inclusion of provision of two stage permit for high rise residential buildings and special buildings;
g) Provisions regarding inspection of completed and occupied building by the Authority from safety point
of view have been made comprehensive;
h) Inclusion of provision empowering engineers/architects for sanctioning plans of residential buildings
up to 500 mz;
j) Provisions for architectural control to effectively take care of the urban aesthetics, have been modified;
and
k) Inclusion of landscape architect and urban designer among the registered professionals for the concerned
applicable works.

PART 2 ADMINISTRATION 3
NATIONAL BUILDING CODE OF INDIA
PART 2 ADMINISTRATION

SECTION 1 GENERAL of last livable floor of the building adjacent to the


external walls; and in the case of pitched roofs, up to
1 SCOPE the point where the external surface of the outer wall
This Part covers the administrative aspects of the Code, intersects the finished surface of the sloping roof, and
such as applicability of the Code, organization of in the case of gables facing the road, the midpoint
building department for enforcement of the Code, between the eaves level and the ridge. Architectural
procedure for obtaining development and building features serving no other function except that of
permits, and responsibility of the owner. decoration shall be excluded for the purpose of
measuring heights.
NOTE— This Code is called the National Building Code of
India, hereinafter referred to as ‘the Code’. 2.7 Building Line — The lineup to which the plinth
of a building adjoining a street or an extension of a
2 TERMINOLOGY
street or on a future street may lawfully extend. It
2.0 For the purpose of this part, the following includes the lines prescribed, if any, in any scheme.
definitions shall apply. The building line may change from time-to-time as
decided by the Authority.
2.1 Accessory Use — Any use of the premises
subordinate to the principal use and customarily 2.8 Conversion — The change of occupancy or
incidental to the principal use. premises to arty occupancy or use requiring additional
occupancy permit.
2.2 Alteration — A change from one type of
occupancy to another, or a structural change, such as 2.9 Development — ‘Development’ with grammatical
an addition to the area or height, or the removal of part variations means the carrying out of building,
of a building, or any change to the structure, such as engineering, mining or other operations in, or over, or
the construction of, cutting into or removal of any wall, under land or water, or in the use of any building or
partition, column, beam, joist, floor or other support, land, and includes redevelopment and layout and
or a change to or closing of any required means of subdivision of any land; and ‘to develop’ shall be
ingress or egress or a change to the fixtures or construed accordingly.
equipment.
2.10 Drain — A conduit or channel for the carriage
2.3 Approved — Approved by the Authority having of storm water, sewage, waste water or other water-
jurisdiction. borne wastes in a building drainage system.

2.4 Authority Having Jurisdiction — The Authority 2.11 Drainage — The removal of any liquid by a
which has been created by a statute and which, for the system constructed for the purpose.
purpose of administering the Code/Part, may authorize
2.12 Occupancy or Use Group — The principal
a committee or an official or an agency to act on its
occupancy for which a building or a part of a building
behalfi hereinafter called the ‘Authority’.
is used or intended to be used; for the purposes of
2.5 Building — Any structure for whatsoever purpose classification of a building according to occupancy,
and of whatsoever materials constructed and every part an occupancy shall be deemed to include the subsidiary
thereof whether used as human habitation or not and occupancies which are contingent upon it.
includes foundation, plinth, walls, floors, roofs,
2.13 Occupier — Occupi&r includes arty person for
chimneys, plumbing and building services, fixed
the time being, paying or liable to pay rent or any
platforms, verandah, balcony, cornice or projection, part
portion of rent of the building in respect of which the
of a buildlng or anything affixed thereto or any wall
ward is used, or compensation or premium on account
enclosing or intended to enclose any land or space
of the occupation of such building and also a rent-free
and signs and outdoor display structures. Tents/
tenant, but does not include a lodger, and the words
SHAMIANAHS, tarpaulin shelters, etc, erected for
‘occupy’ and ‘occupation’ do not refer to the lodger.
temporary and ceremonial occasions with the permission
of the Authority shall not be considered as building. An owner living in or otherwise using his own building
shall be deemed to be the occupier thereof.
2.6 Building, Height of — The vertical distance
measured, in the case of flat roofs from the average 2.14 Operational Construction/Installation — A
level of the ground around and contiguous to the construction/installation put up by Government
building or as decided by the Authority to the terrace Departments for operational purposes (see 12.1.1.1).

PART 2 ADMINISTRATION 5
r
2.15 Owner — Person or body having a legal interest carriageway, footway, square, place or bridge, whether
in land and/or building thereon. This includes free a thoroughfare or not, over which the public have a
holders, leaseholders or those holding a sub-lease right of passage or access or have passed and had access
which both bestows a legal right to occupation and uninterruptedly for a specified period, whether existing
gives rise to liabilities in respect of safety or building or proposed in any scheme and includes all bunds,
condition. channels, ditches, storm-water drains, culverts,
sidewalks, traffic islands, roadside trees and hedges,
In case of lease or sub-leaseholders, as far as ownership
retaining walls, fences, barriers and railings within the
with respect to the structure is concerned, the structure
street lines.
of a flat or structure on a plot belongs to the allottee/
lessee till the allotment/lease subsists. 2.26 Street Level or Grade — The officially
established elevation or grade of the centre line of the
2.16 Permit — A permission or authorization in
street upon which a plot fronts and if there is no
writing by the Authority to carry out work regulated
officially established grade, the existing grade of the y,k
by the Code. }
street at its mid-point.
2.17 Registered Architect, Engineer, Structural
2.27 Street Line — The line defining the side limits
Engineer, Supervisor, Town Planner, Landscape
of a street.
Architect, Urban Designer — A qualified architect,
:
engineer, structural engineer, supervisor, town 2.28 To Erect — To erect a building means:
..
planner, landscape architect or urban designer who
a) to erect a new building on any site whether
has been registered by the Authority or by the body
previously built upon or no~ ~.
governing such profession and constituted under a
b) to re-erect any building of which portions
statute, as may be applicable. The registration
requirements of these professionals shall be as given above the plinth level have been pulled down,
in Annex A. burnt or destroyed.

NOTES 2.29 Unsafe Building — Buildings which are


1 Unless specified otherwise, the word ‘engineer’ shall mean structurally and constructionally unsafe or insanitary
“civil engineer’ or ‘architectural engineer’. or not provided with adequate means of egress or
2 The word ‘licencing/ticensed, etc’ if used by the Authority which constitute a fire hazard or are otherwise
in the above context shall be deemed to mean ‘registration/ dangerous to human life or which in relation to
registered’, etc.
existing use constitute a hazard to safety or health or
2.18 Road — See 2.25. public welfare, by reason of inadequate maintenance,
dilapidation or abandonment.
2.19 Road Line — See 2.27.

2.20 Room Height — The vertical distance measured 3 APPLICABILITY OF THE CODE
from the finished floor surface to the finished ceiling 3.1 All Parts of the Code and their sections shall apply
surface. Where a finished ceiling is not provided, the to all buildings described in 3.2 to 3.8, as may be
underside of the joists or beams or tie beams shall applicable.
determine the upper point of measurement for
determining the head room. 3.2 Where a building is erected, the Code applies to
the design and construction of the building.
2.21 Sanctioned Plan — The set of plans and
3.3 Where the whole or any part of the building is
specifications submitted in connection with a building
removed, the Code applies to all parts of the building
or development and duly approved and sanctioned by
the Authority. whether removed or not.
3.4 Where the whole or any part of the building is
2.22 Service Road — A road/lane provided at the rear
demolished, the Code applies to any remaining part i
or side of a plot for service purposes.
and to the work involved in demolition.
2.23 Set-back Line — A line usually parallel to the
3.5 Where a building is altered (see 12.4 and 12.4.1),
plot boundaries and laid down in each case by the
the Code applies to the whole building whether existing
Authority, beyond which nothing can be constructed
or new except that the Code applies only to part if that
towards the site boundaries.
part is completely self-contained with respect to
2.24 Site (Plot) — A parcel (piece) of land enclosed facilities and safety measures required by the Code.
by definite boundaries.
3.6 Where the occupancy of a building is changed,
2.25 Street — Any means of access, namely, highway, the Code applies to all parts of the building affected
street,’ lane, pathway, alley, stairway, passageway, by the change.

6 NATIONAL BUILDING CODE OF INDIA


3.7 Where development of land is undertaken the Code there are no appropriate test methods specified in the
applies to the entire development of land. Code, the Authority shall determine the test procedure.
For methods of test for buildlng materials, reference
3.8 Existing Buildings/Development may be made to Part 5 Building Materials.
Nothing in the Code shall require the removal, 5.3.2 Copies of the results of all such tests shall be
alteration or abandonment, nor prevent continuance retained by the Authority for a period of not less than
of the use or occupancy of an existing buildingl two years after the acceptance of the alternative material.
development, unless in the opinion of the Authority,
such building/development constitutes a hazard to the SECTION 2 ORGANIZATION AND
safety of the adjacent property or the occupants of the ENFORCEMENT
building itself.
6 DEPARTMENT OF BUILDINGS
4 INTERPRETATION
6.1 The department of buildings shall be created by
4.1 The heading which appears at the beginning of a the Authority and a team of building officials shall be
clause or sub-clause of the Code shall be deemed to be appointed to carry out work of such department.
a part of such clause or sub-clause respectively.
6.2 Appointment of Team of Building Ofllcials
4.2 The use of present tense includes the future tense,
The team of building officials shall be appointed by
the masculine gender includes the feminine and the
the Authority. The team shall comprise officials drawn
neuter, the singular number includes the plural and the
from concerned disciplines such as engineer, architect,
plural includes the singular. The word ‘person’ includes
town planner, landscape architect and urban designer
a corporation as well as an individual; writing includes
as may be decided by the Authority. For scrutiny of
printing and typing and ‘signatur;’ includes thumb
layout plans of plots of one hectare and above in metro
impression made by a person who cannot write if his
cities and two hectares and above in other places, town
name is written near to such thumb impression.
planner. shall be part of the team of building officials.
For plots of five hectares and above, landscape architect
5 ALTERNATIVE MATERIALS, METHODS OF
shall also be part of the team. An urban designer shall
DESIGN AND CONSTRUCTION, AND TESTS
also be required to be the part of team of building
5.1 The provisions of the Code are not intended to officials for examining proposals on integrated’ urban
prevent the use of any material or method of design or design and development for residential/business/
construction not specifically prescribed by the Code, institutional and assembly building.
provided any such alternative has been approved. NOTE — Metro cities are cities with population more than
1000000.
5.2 The Authority may approve any such alternative
provided it is found that the proposed alternative is 6.3 Organization
satisfactory and conforms to the provisions of relevant
In the department of buildings, such number of officers,
parts regarding material, design and construction and
technical assistants, inspectors and other employees
that material, method, or work offered is, for the purpose
shall be appointed to assist the team of building officials
intended, at least equivalent to that prescribed in the
as shall be necessary for the administration of the Code
Code in quality, strength, compatibility, effectiveness,
and as authorized by the Authority.
fire and water resistance, durability and safety.
6.4 Delegation of Powers
5.3 Tests
The Authority may designate one of the building
Whenever there is insufficient evidence of compliance officials who shall exercise all the powers of the team
with the provisions of the Code or evidence that any of building officials. The work of the team of building
material or method of design or construction does not officials may be outsourced to competent professional/
conform to the requirements of the Code or in order to agencylgroup as may be deemed necessary.
substantiate claims for alternative materials, design or
methods of construction not specifically prescribed in 6.5 Qualification of Building Officials
the Code, the Authority may require tests sufficiently The qualification of building officials scrutinizing the
in advance as proof of compliance. These tests shall plans and carrying out inspection of buildlngs shall
be made by an approved agency at the expense of the not in any case be less than those prescribed in
owner. Annex A.
5.3,1 Test methods shall be specified by the Code for 6.5.1 In small local bodies having insufficient
the materials or design or construction in question. If resources to appoint such officials with the above

PART 2 ADMINISTRATION 7
qualifications, two or three such bodies contiguously 7.3 Right of Entry
located could join together and share the services of
Upon presentation of proper credentials and with
one team of building officials.
advance notice, the team of building officials or its
6.6 Qualifications of Assistant duly authorized representative may enter at any
reasonable time any building or premises to perform
No person shall be appointed as Assistant unless he
any duty imposed upon him by the Code.
has got the qualifications prescribed in Annex A for a
registered Supervisor. 7.4 Inspection

6.7 Restriction on Employees The team of building officials shall make all the
required inspections or it may accept reports of
No official or employee connected with the department
inspections of authoritative and recognized services
of buildings except one whose only connection is that
or individuals; and all reports of inspections shall be
of a member of the Board of Appeals, established
in writing and certified by a responsible officer of such
under 8 shall be engaged directly or indirectly in a work
authoritative service or by the responsible individual
connected with the furnishing of labour, materials
or engage any such expert opinion as he may deem
or appliances for the construction, alteration or
necessmy to report upon unusual technical issues that
maintenance of a building, or the preparation of plans
may arise, subject to the approval of the Authority.
or of specifications thereof unless he is the owner of
building; nor shall such official or employee engage 7.5 Construction Not According to Plan
in any work which conflicts with his official duties or
Should the team of building officials determine at any
with the interests of the Department.
stage that the construction is not proceeding according
6.8 Records to the sanctioned plan or is in violation of any of the
provisions of the Code, or any other applicable Code
Proper records of all applications received, permits and
Regulation, Act or Byelaw, it shall notify the owner,
orders issued, inspections made shall be kept and copies
and all further construction shall be stayed until
of all papers and documents connected with the
correction has been effected and approved.
administration of its duties shall be retained and all
such records shall be open to public inspection at all 7.5.1 Should the owner fail to comply with the
appropriate times. requirements at any stage of construction, the Authority
shall issue a notice to the owner asking explanation
7 POWER AND DUTIES OF TEAM OF BUILDING for non-compliance. If the owner fails to comply within
OFFICIALS 14 days from the date of receiving the notice, the
7.0 The team of building officials shall enforce all the Authority shall be empowered to cancel the building
provisions of the Code and shall act on any question permit issued and shall cause notice of such
relative to the mode or manner of construction and the cancellation to be securely pasted upon the said
materials to be used in the erection, addition, alteration, construction, if the owner is not traceable at his address
repair, removal, demolition, installation of service given in the notice. Pasting of such a notice shall be
equipment and the location, use, occupancy and considered sufficient notification of cancellation to the
maintenance of all buildings except as may otherwise owner thereof. No further work shall be undertaken or
be specifically provided. permitted upon such construction until a valid building
permit thereafter has been issued. If the owner, in
7.1 Application and Permits violation of the notice for cancellation, continues the
The team of building officials shall receive all construction, the Authority may take all necessary
applications and issue permits (see 12.10) for the means to stop such work and further appropriate actions
erection and alteration of buildings and examine the including demolitions. tie owner shall, however, have
premises for which such permits have been issued and right to appeal against cancellation of permit, to the
enforce compliance with the Code. board of appeal, within a stipulated period, as maybe
decided by the Authority.
7.2 Building Notices and Orders
7.6 Modification
The team of building officials shall issue all necessary
notices or orders to remove illegal or unsafe conditions, Wherever practical difficulties are involved in carrying
to require the necesstuy safeguards during construction, out any provision of the Code, the team of building
to require adequate exit facilities in existing buildings officials may vary or modify such provisions upon
and to ensure compliance with all the requirements of application of the owner or his representative provided
safety, health and general welfare of the public as the spirit and intent of the Code shall be observed and
included in the Code. public welfare and safety be assured. The application

8 NATIONAL BUILDING CODE OF INDIA


for modification and the final decision of the team of 9.1.3 The registered architect, engineer, structural
building officials shall be in writing and shall be engineer, supervisor, town planner, landscape architect,
officially recorded with the application for the permit urban designer and utility service engineer (see
in the permanent records of the Department of Building Annex A) responsible for the services rendered for
Inspection. supervision of the constructiotidevelopment and for the
completion certificate; in the event of violation of the
7.7 Occupancy Violations
provisions of the Code, shall be liable to penalties as
Wherever any building is being used contrary to prescribed by the Authority including cancellation of
provisions of the Code, the team of building officials registration done by it or make such recommendation
may order such use discontinued and the building or to the statutory body governing such profession.
portion thereof, vacated by the notice served on any 9.2 Further Obligation of Offender
person, causing such use to be discontinued. Such
person shall discontinue the use within 10 days after The conviction of any person for an offence under the
receipt of such notice or make the building or portion provision of 9.1 shall not relieve him from the duty of
thereof, comply with the requirements of the Code. carrying out the requirements or obligations imposed
on him by virtue of the provisions of the Code; and if
8 BOARD OF APPEALS such requirements or obligations are not complied with
in accordance with an order made under provisions
In order to determine the suitability of alternative
of 9.1, the Authority under the provisions of the Code
materials or methods of design or construction and to
may, if necessary and advisable, enter upon the
provide for reasonable interpretation of the provisions
premises in respect of which a conviction has been
of the Code or in the matter of dispute relating to an .-
made and carry out at the expense of the convicted
ongoing construction vis-a-vis the sanctioned plan, a person, the requirements or obligations referred to in
Board of Appeals consisting of members who are the said order and the expense, if not paid on demand,
qualified by experience and training and to pass may be recovered with cost in a court.
judgement upon matters pertaining to building
construction, shall be appointed by the Authority. A 9.3 Conviction No Bar to Further Prosecution
representative of the team of building officials shall The conviction of any person under the provisions of
be an ex-oflcio member and shall act as secretary to this part for failing to comply with any of the said
the Board. The Board shall adopt reasonable rules and requirements or obligations shall not operate as a bar
regulations for conducting its investigations and shall to further prosecution under this part for any
render all decisions and findings in writing to the team subsequent failure on the part of such person to comply.
of building officials with a duplicate copy to the
appellant and may recommend such modifications as 10 POWER TO MAKE RULES
are necessary. The Authority may make rules for carrying out the
provisions and intentions of the Code provided that
9 VIOLATIONS AND PENALTIES
any rule shall not be in direct/indirect conflict or
9.1 Offences and Penalties nullify/dilute any of the provisions of the Code.

9.1.1 Any person who contravenes any of the SECTION 3 PERMIT AND INSPECTION
provisions of the Code or any requirements of
obligations imposed on him by virtue of the Code, or 11 DEVELOPMENT/BUILDING PERMIT
who interferes with or obstructs any person in the
11.1 Permit Required
discharge of his duties, shall be guilty of an offence
and the Authority shall levy suitable penalty or take No person shall carry out any development, erect, re-
other actions as per the Code (see also 7.5 and 15). erect or make alterations or demolish any building or
cause the same to be done without first obtaining a
NOTE — The penalty may be in the form of collection of
arrears of tax, separate permit for each such development/building
from the Authority. No permits shall, however, be
9.1.2 The buildings/developments violating any
required for works referred to in 12.1.1.1 and 12.4.1.
applicable statutory rules shall be demolished/brought
within the limits as prescribed in such rules at the 11.1.1 The development/building permit shall take
expense of the owner. The buildings coming up in the into cognizance the provisions under the relevant Town
vicinity of an aerodrome in violation of the height Planning Act/Development ActlMunicipal Actlany
restriction laid down by the Directorate General of Civil other applicable statutes for layout, building plans,
Aviation shall be accordingly demolished/brought water supply, sewerage, drainage, electrification, etc,
within the limits prescribed by DGCA rules, as provided in the said Act/statute. Also, if so directed

PART 2 ADMINISTIL4TION 9
by the Authority, the permit shall take care of the need 12 APPLICATION FOR DEVELOPMENT/
for landscape development plan incorporating rain- BUILDING PERMIT
water harvesting proposals in the”layout and building
plans. 12.1 Notice

11.1.2 Specific approvals shall be obtained from Every owner who intends to develop, erect, re-erect or
Civil Aviation Authorities, Fire Services Department make alterations in any place in a building shall give
(in case the building proposed is 15 m and above), notice in writing to the Authority of his said intention
Pollution Control Board, designated authorities under in the prescribed form (see Annex B) and such notice
Factories Act/Cinema Regulation Act, Urban Arts shall be accompanied by plans and statements in
Commission, designated Coastal Regulation Zone triplicate as required under 12.2 and 12.3 except for
Authority, Archeological Survey of India, Heritage special buildings (high rise, non-residential) ,where
Committee and any such other authority as may be additional copies may be submitted as desired by the
applicable. Authority. The Authority shall permit submission of I
plarts/documents in electronic form in addition to hard
11.1.3 In order to facilitate clearance from above copy. The Authority should also progressively
bodies with the concept of single window clearance computerize the approval process.
approach and thereby final approval by the Authority
12.1.1 Regarding submission of plans by Government
within the stipulated time frame, the Authority may
Departments, the procedure shall be as given
constitute a Development/Building Permit Approval
in 12.1.1.1 and 12.1.1.2. I
Committee consisting of representative of the team of I
building officials, representatives of all bodies/ 12.1.1.1 The operational construction/installation of
organizations from whom clearance for development the Government, whether temporary or permanent,
building permit clearance is required. which is essential for the operation, maintenance, I
development or execution of any of the following
Recommendations from such Committee shall be
services may be exempted from the point of view of
summarily utilized by the team of building officials
the byelaws:
in sanctioning process. The Committee may meet
once in 15130 days depending upon the work load. a) Railways;
The first response/invalid notice/non-compliance b) National highways;
intimation shall be issued by the Authority to the c) National waterways;
owner within 30 days of submission of the plans to
d) Major ports;
the Authority.
e) Ah-ways and aerodromes;
11.1.4 The Authority shall permit a registered ~
Posts and telegraphs, telephones, wireless,
architectiengineer to approve the building proposals broadcasting, and other like forms of
including plans, and certify completion of building for communications;
issue of related regulatory building permits and
g) Regional grid for electricity;
occupancy certificate for residential buildings designed
h) Defence; and
by self or otherwise, on plot size up to 500 m2. The
responsibility of compliance with respect to provisions j) Any other service which the Central/State
of Code shall rest with the registered architectiengineer. Government may, if it is of opinion that the
However, the plans shall be required to be submitted operation, maintenance, development of
to the Authority for information and record. execution of such service is essential to the
life of thecormnunity, by notification, declare
NOTE— Wherethe experienceclearlyshowsthat satisfactory to be a service for the purpose of this clause.
building permit activities are being carried out through the
above empowerment of professionals, the Authority may In case of constructiordinstdlation where no approvals
extend such provision for larger areas and other building are required, the concerned agencies which are
occupancies.
exempted from seeking approval shall submit the
11.2 Pre-Code Development/Builfing Permit drawings/plans/details for information and records of
the Authority before construction/installation.
If any developmentiuilding, permit for which had
been issued before the commencement of the Code, is 12.1.1.2 However, the following construction of the
not wholly completed within a period of three years Government departments do not come under the
from the date of such permit, the said permission shall purview of operational construction for the purpose of
exemption under 12.1.1.1:
be deemed to have lapsed and fresh permit shall be
necessary to proceed further with the work in a) New residential building (other than gate .
accordance with the provisions of the Code. lodges, quarters for limited essential operational

10 NATIONAL BUILDING CODE OF INDIA


staff and the like), roads and drains in railway 12.2.1.2 The plans shall be coloured as specified in
colonies, hospitals, clubs, institutes and Table 2.
schools, in the case of railways; and .
12.2.2 Key Plan
b) A new building, new construction or new
installation or any extension thereof in the A key plan drawn to a scale of not less than 1 in 10000
case of any other services. shall be submitted along with the application for a
developmenth.tilding permit showing the boundary
12.2 Information Accompanying Notice
locations of the site with respect to neighborhood
The notice shall be accompanied by the key plan, site landmarks. The minimum dimension of the key plan
pian, building plan, services plans, specifications shall be not less than 75 mm.
structural sufficiency certificate and certificate of
12.2.3 Site Plan
supervision as prescribed in 12.2.2 to 12.2.8.
The site plan sent with an application for permit shall
12.2.1 Sizes of Drawing Sheets and Recommended
be drawn to a scale of not less than 1 in 500 for a site
Notation for Colouring Plans
up to one hectare and not less than 1 in 1000 for a site
12.2.1.1 The size of drawing sheets shall be any of more than one hectare and shall show:
those specified in Table 1.
a) the boundaries of the site and of any contiguous
Table 1 Drawing Sheet Sizes land belonging to the owner thereofi
(Clause 12.2.1.1) b) the position of the site in relation to
neighboring street;
S1No. Designation Trimmed Size
mm c) the name of the streets in which the building
(1) (2) (3) is proposed to be situated, if any;
d) all existing buildings standing on, over or
i) AO 841 X 1189
ii) Al 594 X 841
under the site including service lines;
iii) A2 420 X 594 e) the position of the building and of all other
iv) A3 297 X 420 bui~ings (if any) which the applicant intends
v) A4 210 X 297 to erect upon his contiguous land referred to
vi) A5 148 X 210
in (a) in relation to:

Table 2 Colouring of Plans


(Clause 12.2.1.2)

S1 Item Site Plan Building Plan


/
& -
No. - / T

Whhe Plan Blue Print Ammonia Print White Plan Blue Print Ammonia Print
(1) (2) (3) (4) (5) (6) (7) (8)

i) Plot lines Thick black Thick black Thick black Thick black TMck black Thick black
ii) Existing street Green Green Green — — —
iii) Future street, if any Green dotted Green dotted Green dotted — — —
iv) Permissible building Thick dotted Thick dotted Thick dotted — — —
lines black black black
v) Open spa&a No !Monr No colour No CO1OIX No Colour No CO1OW No CO1OUX
vi) Existing wurk Birtclr@ntline) WMe Blue Black White Blue
vii) Work proposed to be %AkXvhatched Yellow hatched Yellow hatched Yellow hatched Yellow hatched Yellow hatched
demolished
viii) Proposed work Red filled in Red Red Red Red Red
(see Note 1)
ix) Drainage and smvcrage Red dotted Red dottrd Red dotted Red dotted Red dotted Red dotted
work
x) Water supply work Black dotted Black dotted Black dotted Black dotted Black dotted Black dotted
thin thin thin thin thin thin

NOTES
1 For entirely new construction this need not be done; for extension of an existing work this shrdl apply.
2 For land development, subdivision, layout, suitable colouring notations shall be used which shall be indexed.

PART 2 ADMINISTRATION 11
1) the boundaries of the site and in case area of the site proposed to be subdivided;
where the site has been partitioned, the and
boundaries of the portion owned by the In case of plots which are subdivided in built-
applicant and also of the portions owned up areas in addition to the above, the means
by others; of access to the sub-division from existing
2) all adjacent street, buildings (with streets.
number of storeys and height) and
12.2.5 Building Plan and Details
premises within a distance of 12 m of the
site and of the contiguous land (if any) The plan of the buildings and elevations and sections
referred to in (a); and accompanying the notice shall be drawn to a scale of
3) if there is no street within a distance of 1:100. The plans and details shall:
12 m of the site, the nearest existing a) include floor plans of all floors together with
street; the covered area clearly indicating the size
f) the means of access from the street to the and spacings of all framing members and sizes
building, and to all other buildings (if any) of rooms and the position of staircases, ramps
which the applicant intends to erect upon his and liftwells;
contiguous land referred to in (a); b) show the use or occupancy of all parts of the
d space to be left about the building to secure a buildings;
free circulation of air, admission of light and c) show exact location of essential services, for
access for scavenging purposes; example, WC, sink, bath and the like;
h) the width of the street (if any) in front and of d) include at least one elevation from the front
the street (if any) at the side or near the showing height of building and rooms and
buildings; also the height of parapet;
j) the direction of north point relative to the plan e) include at least one section through the
of the buildings; staircase;
k) any physical features, such as wells, drains, include the structural arrangements with
f)
etc; and appropriate sections showing typel
m) such other particulars as may be prescribed arrangement of footings, foundations,
by the Authority. basement walls; structural load bearing walls,
columns and beams, and shear walls; and
12.2.4 Sub-DivisiorrlLuyout Plan
arrangementispacing of framing members,
In the case of development work, the notice shall be floor slabs and roof slabs with the material
accompanied by the sub-divisionllayout plan which used for the same,
shall be drawn on a scale of not less than 1 :500 g) show all street elevations;
containing the following: h) give dimensions of the projected portions
a) Scale used and north point; beyond the permissible building line;
b) The location of all proposed and existing j) include terrace plan indicating the drainage
roads with their existing/proposed/prescribed and the slope of the root and
widths within the land; k) give indications of the north point relative to
c) Dimensions of plot along with building lines the plan.
showing the setbacks with dimensions within NOTE — The requirementof 1:100 is permittedto
each plot; be flexible for specific details needed for further
illustration;and.fdsofor drawingsfor thesein electronic
d) The location of drains, sewers, public facilities
form.
and services, and electrical lines, etc;
e) Table indicating size, area and use of all the 12.2.5.1 Building plan for multi -storeyed/special
plots in the sub-division/layout plan; buildings

f) A statement indicating the total area of the For all multi-storeyed buiklings which are 15 m or more
site, area utilized under roads, open spaces in height and for special buildings like educational,
for parks, playgrounds, recreation spaces for assembly, institutional, industrial, storage and
parks, playgrounds, recreation spaces and hazardous and mixed occupancies with any of the
development plan reservations, schools, aforesaid occupancies having covered area more than
shopping and other public places alongwith 500 m2, the building sanction shall be done in two
their percentage with reference to the total stages.

12 NATIONAL BUILDING CODE OF INDIA


F’-

Stage 1: First stage for planning clearance 12.2.6 Services Plans

The following additional information shall be The services plans shall include all details of building
furnished/indicated in the building plan in addition to and plumbing services, and also plans, elevations and
the items given in 12.2.5 as applicable: sections of private water supply, sewage disposal system
and rainwater harvesting system, if any (see Part 8
a) Access to fire appliances/vehicles with details ‘Building Services’ and Part 9 ‘Plumbing Services’).
of vehicular turning circle and clear motorable
accessway around the building; 12.2.7 Specifications

b) Size (width) of main and alternative staircases Specifications, both general and detailed, giving type
along with balcony approach, corridor, and grade of materials to be used, duly signed by the
ventilated lobby approach; registered architect, engineer, structural engineer or
c) Location and details of lift enclosures; supervisor shall accompany the notice (see Annex B).

d) Location and size of fire lift; 12.2.8 Structural Suflciency Certljlcate


e) Smoke stop lobbyldoor, where provided; The plans shall be accompanied by structural
o Refuse chutes, refuse chamber, service duct, sufficiency certificate in the prescribed form (see
etc; Annex C) signed by the engineer/structural engineer
g) Vehicular parking spaces; (see Annex A) and the owner jointly to the effect that
h) Refuse area, if any; the building is safe against various loads, forces and
effects including due to natural disasters, such as,
j) Details of building services — Ai-conditioning
earthquake, landslides, cyclones, floods, etc as per
system with position of fire dampers,
Part 6 ‘Structural Design’ and other relevant Codes.
mechanical ventilation system, electrical
The engineer/stmctural engineer shall also have the
services, boilers, gas pipes, etc;
details to substantiate his design.
k) Details of exits including provision of ramps,
etc, for hospitals and special risks; 12.2.9 Supervision
m) Location of generator, transformer and The notice shall be further accompanied by a certificate
switchgem room; in the prescribed form (see Annex D) by the registered
n) Smoke exhauster system, if any; architect/engineer/stmctural engineer/supervisor/town
Details of fwe alarm system network; planner (see Annex A) undertaking the supervision
P)
(see 9.3).
q) Location of centralized control, connecting
all fire alarm systems, built-in-fire protection 12.3 Preparation and Signing of Plans
arrangements and public address system,
The registered architect/engineer/supervisor/town
etc;
planner/landscape architect/urban designer/utility
r) Location and dimensions of static water
service engineer shall prepare and duly sign the plans
storage tank and pump room along with fwe as per their competence (see Annex A) and shall
service inlets for mobile pump and water indicate his/her name, address, qualification and
storage tank; registration number as allotted by the Authority or the
s) Location and details of fixed fire protection body governing such profession. The structural plans
installations, such as, sprinklers, wet risers, and details shall also be prepared and duly signed by
hose-reels, drenchers, etc; and the competent professionals like registered engineer/
t) Location and details of first-aid fire fighting structural engineer (see Annex A). The plans shall also
equipments/installations. be duly signed by the own.w indicating his address.
The type and volume of buildings/development work
Stage 2: Second stage for building permit clearance to be undertaken by the registered professionals may
After obtaining the sanction for planning (Stage 1) generally be as in Annex A.
from the Authority, a complete set of structural plans, 12.4 Notice for Alteration only
sections, details and design calculations duly signed
When the notice is only for an alteration of the building
by engineer/structural engineer (see Annex A) along
(see 3.5), only such plans and statements, as maybe
with the complete set of details duly approved in
necessmy, shall accompany the notice.
Stage 1 shall be submitted. The building plans/details
shall be deemed sanctioned for the commencement of 12.4.1 No notice and building permit is necessary for
construction only after obtaining the permit for Stage 2 the following alterations, and the like which do not
from the Authority. otherwise violate any provisions regarding general

PART 2 ADMINISTRATION 13
building requirements, structural stability and fire and 12.9 Qualifications of Architects/Engineers/
health safety requirements of the Code: Structural Engineers/Landscape ArchitectNrban
Designer/Supervisors/Town Planners/Services
a) Opening and closing of a window or door or
Personnel
ventilator;
b) Providing intercommunication doors; Architects, engineers, structural engineers, landscape
c) Providing partitions; architect, urban designer, supervisors and town
planners wherever referred in the Code, shall be
d) Providing false ceiling;
registered by the Authority or the body governing such
e) Gardening; profession constituted under a statute, as competent to
o White washing; do the work for which they are employed. A guide for
g) Painting; the equivalent technical qualifications and professional
h) Re-tiling and reproofing; experience required for such registration with the
Plastering and patch work; Authority is given in Annex A. In case of building and
j)
plumbing services, qualifications for engineers for
k) Re-flooring; and
utility services shall be as given in A-2.8.
m) Construction of sunshades on one’s own land.
12.9.1 In case the registered professional associated
12.5 Fees with the preparation and signing of plans or for
supervision, is being changed during any stage of
No notice as referred to in 12.1 shall be deemed valid
buildingfland development process, the professional
unless and until the person giving notice has paid the
shall intimate the Authority in writing about the further
fees to the Authority and an attested copy of the receipt
non-association with the project.
of such payment is attached with the notice.
NOTE — The fees may be charged as a consolidatedfee. In 12.10 Grant of Permit or Refusal
the event of a building/developmentpermit is not issued, the
fees so paid shall not be returnedto the owner,but he shall be The Authority may either sanction or refuse the plans
allowed to re-submitit without any fees after complyingwith and specifications or may sanction them with such
all the objections raised by the Authority within a period of modi~cations or directions as it may deem necessmy
one year from the date of rejectionafter whichfresh fees shall and thereupon shall communicate its decision to the
have to be paid.
person giving the notice (see Annex E).
12.6 Duration of Sanction 12.10.1 The building plans for buildings identified
The sanction once accorded shall remain valid up to in 12.2.5.1 shall also be subject to the scrutiny of the
three years. The permit shall be got revalidated before Fire Authority and the sanction through building permit
the expiration of this period. Revalidation shall be shall be given by the Authority after the clearance from
subject to the rules then in force. the Fire Authority (see also 11.1.3).

12.10.2 If within 30 days of the receipt of the notice


12.7 Deviations During Construction
under 12.1 of the Code, the Authority fails to intimate
If during the construction of a building any departure in writing to the person, who has given the notice, of
(excepting for items as given in 12.4.1) from the its refusal or sanction, the notice with its plans and
sanctioned plan is intended to be made (see 7.5), statements shall be deemed to have been sanctioned;
sanction of the Authority shall be obtained before the provided the fact is immediately brought to the notice
change is made. The revised plan showing the of the Authority in writing by the person who has given
deviations shall be submitted and the procedure laid notice and having not received any intimation from
down for the original plan heretofore shall apply to all the Authority within MJeen days of giving such written
such amended plans except that the time limit specified notice. Subject to the conditions mentioned in this
in 12.10.2 shall be three weeks in such cases. clause, nothing shall be construed to authorize any
person to do anything in contravention of or against
12.8 Revocation of Permit the terms of lease or titles of the land or against any
other regulations, byelaws or ordinance operating on
The Authority may revoke any permit issued under
the site of the work.
the provisions of the Code, wherever there has been
any false statement, misrepresentation of any material 12.10.3 In the case of refusal, the Authority shall quote
fact in the application on which the permit was the reason and relevant sections of the Code which the
based or violation of building permit or in case of plans contravene. The Authority shall as far as possible
noncompliance thereof, and shall state the reasons for advise all the objections to the plans and specifications
revoking the permit. in the first instance itself and ensure that no new

14 NATIONAL BUILDING CODE OF INDIA


objections are raised when they are resubmitted after occupancy for a building or part thereof, before the
compliance of earlier objections. entire work covered by permit shall have been
completed, provided such portion or portions may be
12.10.4 Once the plan has been scrutinized and
occupied safely prior to full completion of building
objections have been pointed out, the owner giving
without endangering life or public welfare.
notice shall modify the plan to comply with the
objections raised and re-submit it. The Authority shall 13.3 Documents at Site
scrutinize the re-submitted plan and if there be further
objections, the plan shall be rejected. 13.3.1 Where tests of any materials are made to ensure
conformity with the requirements of the Code, records
13 RESPONSIBILITIES AND DUTIES OF THE of the test data shall be kept available for inspection
OWNER during the construction of the building and for such a
13.1 Neither the granting of the permit nor the approval period thereafter as required by the Authority.
of the drawings and specifications, nor inspections 13.3.2 The person to whom a permit is issued shall
made by the Authority during erection of the building during construction keep pasted in a conspicuous place
shall in any way relieve the owner of such building on the property in respect of which the permit was
from full responsibility for carrying out the work in issued:
accordance with the requirements of the Code (see 9).
a) a copy of the building permit; and
13.2 Every owner shall: b) a copy of the approved drawings and
a) permit the Authority to enter the building or specifications referred in 12.
premises for which the permit has been
14 INSPECTION, OCCUPANCY PERMIT AND
granted at any reasonable time for the purpose
POST-OCCUPANCY INSPECTION .
of enforcing the Code;
b) submit a document of ownership of the site; 14.1 Generally all construction or work for which a
c) obtain, where applicable, from the Authority, permit is required shall be subject to inspection by the
permits relating to building, zoning, grades, Authority and certain types of construction involving
sewers, water mains, plumbing, signs, unusual hazards or requiring constant inspection shall
blasting, street occupancy, electricity, have continuous inspection by special inspectors
highways, and all other permits required in appointed by the Authority.
connection with the proposed work; 14.2 Inspection, where required, shall be made within
d) give notice to the Authority of the intention 7 days following the receipt of notification, after
to start work on the building site (see which period the owner will be free to continue the
Annex F); construction according to the sanctioned plan. At the
e) give written notice to the Authority intimating first inspection, the Authority shall determine to the
completion of work up to plinth level; best of its ability that the building has been located
submit the certificate for execution of work in accordance with the approved site plans. The final
f)
as per structural safety requirements (see inspection of the completion of the work shall be
Annex G); and give written notice to the made within 21 days following the receipt of
Authority regarding completion of work notification [see 13.2(f)] for the grant of occupancy
described in the permit (see Annex H); certificate.

g) give written notice to the Authority in case of 14.2.1 The owner/concerned registered architect/
termination of services of a professional engineer/structural eng@eer/town planner will serve
engaged by him; and a notice/completion certificate to the Authority that
h) obtain an occupancy permit (see Annex J) the building has been completed in all respects as per
from the Authority prior to any: the approved plans. The deviations shall also be
brought to the notice of the Authority (with relevant
1) occupancy of the building or part thereof
documents). The team of building officials or its duly
after construction or alteration of that
authorized representative shall then visit the site and
building or part, or
occupancy certificate shall be given in one instance.
2) change in the class of occupancy of any
building or part thereof. . 14.2.2 The occupancy certificate should clearly state
the use/type of occupancy of the building. However,
13.2.1 Temporary Occupancy
the applicant can apply for change of useioccupancy
Upon the request of the holder of the permit, the permitted within the purview of the Master Plan/Zonal
Authority may issue a temporary certificate of Plan/Building Byelaws, where so required.

PART 2 ADMINISTRATION 15
14.3 When inspection of any construction operation 15.3.1 The Authority may direct in writing that the
reveals than any lack of safety precautions exist, the building which in his opinion is dangerous, or has
Authority shall have right to direct the owner to stop no provision for exit if caught fire, shall be vacated
the work immediately until the necessary remedial immediately or within the period specified for the
measures to remove the violation of safety precautions purpose; provided that the Authority concerned shall
are taken. keep a record of the reasons for such action with
\
him.
14.4 Periodic Occupancy Renewal Certificate
If any person does not comply with the orders of
14.4.1 For buildings covered in 12.2.5.1 after vacating a building, the Authority may direct the police
completion of the building and obtaining the occupancy to remove the person from the building and the police
certificate, periodic inspections of buildings shall be shall comply with the orders.
made by the Fire Authority to ensure the fiie safety of
the building and compliance with the provisions of fire 15.4 Disregard of Notice
and life safety requirements (see Part 4 ‘Fire and Life
In case the owner or occupier fails, neglects, or refuses
Safey’). Periodic occupancy renewal certificate shall
to comply with the notice to repair or to demolish the
be made available by the Authority/Fire Authority which
said building or portion thereof, the Authority shall
shall also include safekeep of f~e fighting installations
cause the danger to be removed whether by demolition
and equipments for such buildings.
or repair of the building or portion thereof or otherwise.
14.4.2 All occupied building and buildings covered
under 12.2.5.1 shall also be subjected to periodic 15.5 Cases of Emergency
physical inspection by a team of multi-disciplinary
In case of emergency, which, in the opinion of the
professionals of local Authority. The work by team of
Authority involves imminent danger to human life or
professionals may be outsourced by the Authority to
health, the decision of the Authority shall be final. The
competent professionals as maybe deemed necessary.
Authority shall forthwith or with such notice as may
The team shall ensure the compliance of byelaws,
be possible promptly cause such building or portion
natural lighting, ventilation, etc, besides structural and
thereof to be rendered safe by retrofittingkengthening
electrical safety. After checking, the team shall be
to the same degree of safety or removed. For this
required to give the certificate for above aspects. If
purpose, the Authority may at once enter such structure
any shortcoming/deficiencies or violations are noticed
or land on which it stands, or abutting land or structure,
during inspection, the Authority shall ensure the
with such assistance and at such cost as may be deemed
compliance of these within a specified time frame of
necessary. The Authority may also get the adjacent
six months. If not complied with, the building shall be
structures vacated and protect the public by an
declared unsafe. The period of inspection shall usually
appropriate fence or such other means as may be
be 3 to 5 years but in any case not more than 5 years.
necessary.
15 UNSAFE BUILDING
15.6 Costs
15.1 All unsafe buildings shall be considered to
Costs incurred under 15.4 and 15.5 shall be charged to
constitute danger to public safety and shall be restored
the owner of the premises involved. Such costs shall
by repairs or demolished or dealt with as otherwise
be charged on the premises in respect of which or for
directed by the Authority (see 15.2 to 15.5).
the benefit of which the same have been incurred and
15.2 Examination of Unsafe Building shall be recoverable as provided under the laws (see
Note).
The Authority shall examine or cause to be examined
every building reported to be unsafe or damaged, and NOTE— The costs may be in the form of arrearsof taxes.
shall make a written record of such examination.
16 DEMOLITION OF BUILDING
15.3 Notice to Owner, Occupier
Before a building is demolished, the owner shall notify
Whenever the Authority finds any building or portion all utilities having service connections within the
thereof to be unsafe, it shall, in accordance with building, such as water, electric, gas, sewer and other
established procedure for legal notice, give to the owner connections. A permit to demolish a building shall not
and occupier of such building written notices stating be issued until a release is obtained from the utilities
the defects thereof. This notice shall require the owner stating that their respective service connections and
or the occupier within a stated time either to complete appurtenant equipment, such as, meters and regulators
specified repairs or improvements or to demolish and have been removed or sealed and plugged in a safe
remove the building or portion thereof. manner.

16 NATIONAL BUILDING CODE OF INDIA


17 VALIDITY Code from the point of view of structural safety and
functional requirements.
17.1 Partial Invalidity
18.2 An Urban Arts Commission shall be established
In the event any part or provision of the Code is held at the city/state level on issues related to urban
to be illegal or void, this shall not have the effect of aesthetics, through a statute. This statutory authority/
making void or illegal any of the other parts or commission established by an Act of State Legislative
provisions thereof, which may or shall be determined Assembly, shall accord approval to all major buildings/
to be legal, and it shall be presumed that the Code important development projects having bearing on the
would have been passed without such illegal or invalid urban aesthetics, depending upon the importance of
parts or provisions. the area with respect to natural or built heritage or
projects on plot areas above 1 hectare and located
17.2 Segregation of Invalid Provisions
in specifically identified areas. The Urban Arts
Any invalid part of the Code shall be segregated Commission shall act as guardian of urban architecture;
from the remainder of the Code by the court holding mainly with regard to building form and envelope, the
such part invalid, and the remainder shall remain relationship between the building, and the ambient
effective. environment vis-a-vzk other dependants should be seen
in depth.
17.3 Decisions Involving Existing Buildings
18.3 The Commission may work in the following
The invalidity of any provision in any clause of the manner:
Code as applied to existing buildings and structures
a) The Commission may select only the
shall not be held to effect the validity of such section
in its application to buildings hereafter erected. important buildings as in 18.1 and examine
the same. The person responsible for the
18 ARCHITECTURAL CONTROL schemes, say an architect or an engineer, may
examine either alone or with the owner. A
18.1 Compliance with the provisions of the Code is
study of the plans, elevations, models, etc,
adequate for normal buildings. But for major public
should be made. The architect/engineer
building complexes or buildings coming up in an
should explain in general terms the purposes
important area near historic/monumental buildings and
which the building is to serve and the main
areas of heritage, the aesthetics of the whole scheme
conditions which have influenced him in
may also have to be examined, vis-a-vis existing
preparing the design.
structures. In addition, any development which may
b) The Commission after full discussion, may
mar the general characteristics and environment of
communicate their decision in writing to the
historical, architectural or other monuments should also
parties concerned. The Commission may
be subject to the provisions of this clause. This clause
recommend a change in the whole scheme or
is intended to cover very few structures to come up in
suggest modifications in the existing scheme,
the vicinity of other declaredhistorically important
if so required.
structures, and the scrutiny shall be limited to the
external architectural features only so as to ensure an 18.4 The Urban Arts Commission should also be
aesthetic continuance of the existing structures with charged with advising the city government, on schemes
the new. The scrutiny shall not deal with the routine which will beautify the city and add to its cultural
building plan scrutiny from other requirements of vitality.

PART 2 ADMINISTRATION 17
ANNEX A

(Foreword and Clauses 2.17,6.5,6.6,9.1.3, 12.2.8, 12.3 and 12.9)

GUIDE FOR THE QUALIFICATIONS AND COMPETENCE OF PROFESSIONALS

A-1 ESSENTIAL REQUIREMENTS Engineering Division of the Institution of Engineers


(India) or the statutory body governing such profession,
A-1.l Every building/development work for which
as and when established.
permission is sought under the Code shall be planned,
designed and supervised by registered professionals. A-2.2.1 Competence
The registered professionals for carrying out the
The registered engineer shall be competent to carryout
various activities shall be: (a) architect, (b) engineer,
the work related to the building/development permit
(c) structural engineer, (d) supervisor, (e) town planner,
as given below:
(f) landscape architect, (g) urban designer, and
(h) utility service engineer. Requirements of a) All plans and information connected with
registration for various professionals by the Authority building permit;
or by the body governing such profession and b) Structural details and calculations of buildings
constituted under a statute, as applicable to practice on plot up to 500 m2 and up to 5 storeys or
within the local body’s jurisdiction, are given in A-2.1 16 m in height;
to A-2.5. The competence of such registered personnel c) Issuing certificate of supervision and
to carry out various activities is also indicated completion for all buildings;
in A-2.1.1 to A-2.5.1.
d) Preparation of all service plans and related
A-2 REQUIREMENTS FOR REGISTRATION information connected with development
AND COMPETENCE OF PROFESSIONALS permit; and
e) Issuing certificate of supervision for
A-2.1 Architect
development of land for all area.
The minimum qualifications for an architect shall be
A-2.3 Structural Engineer
the qualifications as provided for in the Architects Act,
1972 for registration with the Council of Architecture. The minimum qualifications for a structural engineer
shall be graduate in civil engineering of recognized
A-2.1.1 Competence
Indian or foreign university, or Corporate Member of
The registered architect shall be competent to carryout Civil Engineering Division of Institution of Engineers
the work related to the building/development permit (India), and with minimum 3 years experience in
as given below: structural engineering practice with designing and field
a) All plans and information connected with work.
building permit except engineering services NOTE— The 3 years experienceshallbe relaxedto 2 years in
of multistoreyed/special buildings given thecaseof post-graduatedegreeof recognizedIndianor foreign
university in the branch of structural engineering.In case of
in 12.2.5.1.
doctorate in structural engineering, the experience required
b) Issuing certificate of supervision and would be one year.
completion of all buildings pertaining to
A-2.3.1 Competence
architectural aspects.
c) Preparation of sub-divisionllayout plans and The registered structural engineer shall be competent
related information connected with to prepare the structural design, calculations and details
development permit of area up to 1 hectare for all buildings and supervision.
for metro-cities and 2 hectare for other places. A-2.3.1.1 In case of buildings having special structural
d) Issuing certificate of supervision for features, as decided by the Authority, which are within
development of land of area up to 1 hectare the horizontal areas and vertical limits specified
for metro-cities and 2 hectare for other places. in A-2.2 .l(b) and A-2.4.l(a) shall be designed only
by structural engineers.
A-2.2 Engineer
A-2.4 Supervisor
The minimum qualifications for an engineer shall be
graduate in civil engineering/architectural engineering The minimum qualifications for a supervisor shall
of recognized Indian or foreign university, or the be diploma in civil engineering or architectural
Member of Civil Engineering Division/Architectural assistantship, or the qualification in architecture or

18 NATIONAL BUILDING CODE OF INDIA


engineering equivalent to the minimum qualification building/development permit for land areas 5 hectares
prescribed for recruitment to non-gazetted service by and above. In case of metro-cities, this limit of land
the Government of India plus 5 years experience in area shall be 2 hectares and above.
building design, construction and supervision. NOTE — For smallerareas below tbe limits indicatedabove,
A-2.4.1 Competence associationof landscapearchitectmay also be consideredfrom
the point of view of desired landscapedevelopment.
The registered supervisor shall be competent to carryout
A-2.7 Urban Designer
the work related to the building permit as given below:
The minimum qualification for art urban designer shall
a) All plans and related information connected
be the master’s degree in urban design or equivalent
with building permit for residential buildings
from recognized Indian or foreign university.
on plot up to 100 m2 and up to two storeys or
7.5 m in height; and A-2.7.1 Competence
b) Issuing certificate of supervision for buildings
The registered urban designer shall be competent to
as per (a).
carryout the work related to the building permit for
A-2.5 Town Planner urban design for land areas more than 5 hectares and
campus area more than 2 hectares. He/She shall also
The minimum qualification for a town planner shall
be competent to carryout the work of urban renewal
be the Associate Membership of the Institute of Town
for all areas.
Planners or graduate or post-graduate degree in town
and countly planning. NOTE — For smatter areas below the limits indicatedabove,
associationof urbandesignermaybe consideredfromthe point l.-

A-2,5.1 Competence of view of desired urban design.

The registered town planner shall be competent to A-2.8 Engineers for Utility Services
carry out the work related to the development permit
For buildings identified in 12.2.5.1, the work of
as given below:
building and plumbing services shall be executed under
a) Preparation of plans for land sub-division/ the planning, design and supervision of competent
layout and related information connected with personnel. The qualification for registered mechanical
development permit for all areas. engineer (including HVAC), electrical engineer and
b) Issuing of certificate of supervision for plumbing engineers for carrying out the work of Air-
development of land of all areas. conditioning, Heating and Mechanical Ventilation,
NOTE — However,for land layouts for development Electrical Installations, Lifts and Escalators and Water
permit above 5 hectare in area, landscape architect Supply, Drainage, Sanitation and Gas Supply
shall also be associated, and for land development installations respectively shall be as given in Part 8
infrastructural services for roads, water supplies, ‘Building Services’ and Part 9 ‘Plumbing Services’ or
sewerage/drainage,electrification, etc. the registered
engineersfor utility services shall be associated. as decided by the Authority taking into account
practices of the National professional bodies dealing
A-2.6 Landscape Architect with the specialist engineering services.
The minimum qualification for a landscape architect
A-3 BUILDEWCONSTRUCTOR ENTITY
shall be the bachelor or master’s degree in landscape
architecture or equivalent from recognized Indian or The minimum qualification and competence for the
foreign university. builder/constructor entity for various categories of
building and infrastructural development shall be as
A-2.6.1 Competence
decided by the Authority to ensure compliance of
The registered landscape architect shall be competent quality, safety and construction practices as required
to carrvout the work related to landscape design for under the Code.

PART 2 ADMINISTRATION 19
ANNEX B
(Clause 12.1)
FORM FOR FIRST APPLICATION TO DEVELOP, ERECT, RE-ERECT OR TO MAKE
ALTERATION IN ANY PLACE IN A BUILDING

To

........................................
........................................
........................................

Sir,

I hereby give notice that I intend to develop, erect, re-erect or to make alteration in the building No .............................
or to .........................................................otiin Plot No ......................................................................... in Colony/
Street .............................................MOHALUfBA~RRoad .............................................City ...........................and
in accordance with the building code of ...............................................Pti II, Clauses .....................................and
I forward herewith the following plans and specifications in triplicate duly signed by me and .....................................
the Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architect/Urban Designer]),
Registration No. ........................................... who will supervise its erection.

(Name in block letters)

1. Key plan
2. Site plans
3. Sub-divisionllayout plan
4. Building plans
5. Services plans
6. Specifications, general and detailedz)
7. Thle of ownership of landhttildlng
8. Certificates for structural sufficiency and supervision

I request that the developmenticonstrttction may be approved and permission accorded to me to execute the
work.

Signature of Owner ......................................................


Name of the Owner ......................................................
(in block letters)
Address of Owner ......................................................
......................................................
......................................................
......................................................
......................................................

Date: ..........................

II Stnke out whichever is not applicable.


21A fomat may be prepared by the Authority for direct use.

20 NATIONAL BUILDING CODE OF INDIA


ANNEX C

(Clause 12.2.8)

FORM FOR CERTIFICATE FOR STRUCTURAL DESIGN SUFFICIENCY

With respect to the building work of erection, re-erection or for making alteration in the building
No ................................orto ......................................................otiin Plot No. ...................................................Colony/
Street .....................................MOHALLA/BAZ4R/Road ... ....................................................City ..................................
we certify that the structural plans and details of the building submitted for approval satisfy the structural safety
requirements for all situations including natural disasters, as applicable, as stipulated under Part 6 Structural
Design of the National Building Code of India and other relevant Codes; and the information given therein is
factually correct to the best of our knowledge and understanding.

Signature of owner Signature of the


with date Registered Engineer/
Structural Engineer with
date and registration No.
Name: ........................................... ..........................................

Address: ........................................... ..........................................


. ..-.

ANNEX D h’....
–,
(Clause 12.2.9)
FORM FOR SUPERVISION

I hereby certify that the development, erection, re-erection or material alteration in/of building No ..............................
or the ...................................................................otiin Plot No .................................................................in Colony/
Street .......................................MOHALM/BA~R~oad . .... ............................................. City ..................................
shall be carried out under my supervision and I certify that all the materials (type and grade) and the workmanship
of the work shall be generally in accordance with the general and detailed specifications’ submitted along with,
and that the work shall be carried out according to the sanctioned plans.

Signature of Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architect/Urban


Designeri~ ......................................................

Name of Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architect/Urban


DesignerlJ ......................................................
(in block letters)

Registration No. of Architect/Engineer/Stmctural Engineer/Supervisor/’Town Planner/Landscape Architect/Urban —


Designer’) ......................................................

Address of Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architect/Urban


Designer]l ......................................................
.......................................................
.......................................................
.......................................................

Date: ........................

1)Strike out whicheveris not applicabk

PART 2 ADMINISTRATION 21
ANNEX E

(Clause 12.10)
FORM FOR SANCTION OR REFUSAL OF DEVELOPMENT/BUILDING PERMIT

To

...............................................

Sir,

With reference to your application ........................................dated ........................................for grant of permit


for the development, erection, re-erection or material alteration in the building No. ........................................
or to ....................................................on/in Plot No ....................................................................in Colony/
Street ............................................MOHALU/BA~~oad. ..........................................City ...............................

I have to inform you that the sanction has been granted/refused by the Authority on the following grounds:

1.
2.
3.
4.
5.
6.

Office Stamp ............................................... Signature of the Authority ........................................

Office (Communication) No. ...................... Name, Designation and Address


of the Autiotity .......................................................
Date: ............................ .......................................................

ANNEX F

[Clause 13.2 (d)]


FORM FOR NOTICE FOR COMMENCEMENT

I hereby certify that the development, erection, re-erection or material alteration in/of building No. ...........................
or the ..............................ort/in Plot No ....................................in Colony/SUeet .....................................MOHAU/
BAZARIRoad ....................................City ....................................will be commenced on as per your permission,
vide No .....................................dated ..............................under the supervision of ....................................Registered
Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architect/Urban DesignerlJ,
Registration No ...............................................................and in accordance with the plans sanctioned, vide
No . . ...................................&ted ............................

Signature of Owner ....................................................


Name of Owner ..........................................................
(in block letters) 8
?
Address of Owner ....................................................... i
!
.......................................................
Date: ............................

u ,’jtrikeout whicheveris not applicable.

22 NATIONAL BUILDING CODE OF INDIA


ANNEX G

[Clause 13.2(f)]

FORM FOR CERTIFICATE FOR EXECUTION OF WORK AS PER


STRUCTURAL SAFETY REQUIREMENTS

With respect to the building work of erection, re-erection or for making alteration in the building No ..........................
or to ................................on/in Plot No .......................................Colonylstreet ...................................MOHALGV
BAZARIRoad ................................City ................................. we certify:
a) that the building has been constructed according to the sanctioned plan and structural design (one set of
drawings as executed enclosed), which incorporates the provisions of structural safety as specified in
Part 6 ‘Structural Design’ of the National Building Code of India and other relevant Codes; and
b) that the construction has been done under our supervision and guidance and adheres to the drawings and
specifications submitted and records of supervision have been maintained.

Any subsequent changes from the completion drawings shall be the responsibility of the owner.

Signature of owner Signature of the


with date Registered Engineer/
Structural Engineer with
date and registration No.
Name: ........................................... ..........................................

Address: ........................................... ..........................................

ANNEX H

[Clause 13.2 (f)]


FORM FOR COMPLETION CERTIFICATE

I hereby certify that the development, erection, re-erection or material alteration in/of building No ...........................
or the ........................... on/in Plot No ............................ in ColonylStreet ........................... MOHALLAIBAZARI
Road ...........................City ...........................hasbeen supemised bymeand has been completed on ...........................
........................... according to the plans sanctioned, vide No. ........................... dated ...................... The work
has been completed to my best satisfaction, the workmanship and all the materials (type and grade) have been
used strictly in accordance with general and detailed specifications. No provisions of the Code, no requisitions
made, conditions prescribed or orders issued thereunder have been transgressed in the course of the work. The
land is fit for construction for which it has been developed or re-developed or the building is fit for use for which
it has been erected, re-erected or altered, constructed and enlarged.

I hereby also enclose the plan of the building completed in all aspects.

Signature of Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architec~rban


Designer’) .....................................................................

Name of Architect/Engineer/S tructural Engineer/Supervisor/Town Planner/Latidscape Architect/Urban


DesignerlJ .....................................................................
(in block letters)

Registration No. of Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architect/Urban


Designer lJ .....................................................................

Address of Architect/Engineer/Structural Engineer/Supervisor/Town Planner/Landscape Architect/Urban


Designer]) .....................................................................

Date: ............................. Signature of the Owner

IJ Strjke out whicheveris not applicable.

PART 2 ADMINISTRATION 23
CONTENTS

FOREWORD .. . 3

1 SCOPE ... 7
2 TERMINOLOGY ... 7
3 LAND USE CLASSIFICATION AND USES PERMITTED ... 12
4 MEANS OF ACCESS ... 13
5 COMMUNITY OPEN SPACES AND AMENITIES . .. 15
6 REQUIREMENTS OF PLOTS ... 21
7 CLASSIFICATION OF BUILDINGS ... 22
8 OPEN SPACES (WITHIN A PLOT) ... 23
9 AREA AND HEIGHT LIMITATIONS ... 26
10 OFF-STREET PARKING SPACES ... 28
11 GREENBELTS, LANDSCAPING AND WATER CONSERVATION ... 29
12 REQUIREMENTS OF PARTS OR BUILDINGS ... 29
13 FIRE AND LIFE SAFETY ... 34
14 DESIGN AND CONSTRUCTION ... 34
15 LIGHTING AND VENTILATION ... 34
16 ELECTRICAL AND ALLIED INSTALLATIONS (INCLUDING LIGHTNING ... 35
PROTECTION OF BUILDINGS)
17 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION ... 35
18 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL ... 35
19 HEAT INSULATION ... 35
20 INSTALLATION OF LIFES AND ESCALATORS ... 35
21 PLUMBING SERVICES AND SOLID WASTE MANAGEMENT . .. 35

ANNEX A CIVIL AVIATION REQUIREMENTS FOR CONSTRUCTION IN ... 36


THE VICINITY OF AN AERODROME.
ANNEX B OFF-STREET PARKING SPACES ... 41
ANNEX C SPECIAL REQUIREMENTS FOR LOW INCOME HOUSING IN ... 42
URBAN AREAS
ANNEX D SPECIAL REQUIREMENTS FOR PLANNING OF PUBLIC ... 45
BUILDINGS MEANT FOR USE OF PHYSICALLY CHALLENGED
ANNEX E SPECIAL REQUIREMENTS OF CLUSTER PLANNING FOR ... 56
HOUSING
ANNEX F SPECIAL REQUIREMENTS FOR LOW INCOME HABITAT ... 57
PLANNING IN RURAL AREAS
ANNEX G SPECIAL REQUIREMENTS FOR DEVELOPMENT PLANNING ... 60
IN HILLY AREAS

LIST OF STANDARDS ... 63

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Part covers development control rules, including such aspects as sub-division and layout rules, land use
classifications, open spaces, area and height limitations, means of access, and parking spaces; this part also
covers the general building requirements, such as the requirements of parts of buildings, provision of lifts, etc.

It is expected that for proper coordination and enforcement of the development control rules and general building
requirements, the departments concerned, namely, the town planning department and the building department,
will coordinate the total development and building activity at both organizational and technical levels.

Particular attention is invited to Table 3 on floor area ratio (FAR) limitations. It is emphasized that the floor area
of a single storey building is limited in absolute terms by the type of construction and occupancy class. Also, the
absolute floor areas for different types of construction and different occupancies have a definite ratio among
them. The ratios as recommended in the American Iron and Steel Institute publication 1961 ‘Fire Protection
Through Modem Building Codes’ have been generally adopted in this Part and Table 3 has been developed on
this basis. Table 3 is repeated in Part 4 ‘Fire and Life Safety’ also for convenience of reading.

Limitation of areas and heights of buildings is achieved in this country by specifying it in terms of floor area ratio
(FAR) or floor space index (FSI). The significance of the contribution of different types of construction giving
different fire resistances has not been taken cognizance of in specifying FAR for different occupancies, in the
present development control rules and municipal byelaws of the country. Table 3, therefore, gives the comparative
ratios of FAR between types of buildings and occupancy classes and these have been specified mainly from the
fire protection aspect of buildings. To arrive at the actual FAR for different buildings coming up in different
areas, the Authority should further modify them, by taking into consideration other aspects like density of any
area, parking facilities required, the traffic load (road width) and the services available. The heights of buildings
shall also be regulated, keeping in view the local fire fighting facilities.

In some state byelaws, the FAR (or FSI) has been expressed in the form of percentage. However, the Committee
responsible for preparation of this Code is of the opinion that, it being a ratio should be expressed only in the
form of a ratio, as done in this Part.

It is particularly to be borne in mind by the Authority that the ratios are definitive and it can assess the particular
FAR for a type of construction and for an occupancy and establish a new table, but retaining the comparative
ratios as given in Table 3.

Keeping in view the enormous problems faced by the country with regard to the ever increasing squatter settlements/
pavement dwellers in urban areas (cities of all sizes), it is imperative that all the urban local bodies sooner or later
evolve schemes for their rehabilitation. The resources are meagre and the problems are enormous. There has
been a tendency on the part of a number of development agenciesflocal bodies to link space norms with
affordability. Affordability is an important criterion but at the same time a public agency cannot ignore the basic
minimum needs of the family to be housed (including the mental, physical and social health of the marginalized
groups, which is linked with shelter). The local bodies shall have to evolve appropria~ policies for their integration
with the broad urban society and generate/allocate resources and more importantly adopt a planning process,
which are people friendly. The Government of India has also formulated the National Slum Policy to this effect.
Therefore, keeping in view the needs of low income housing, to cater to Economically Weaker Sections of
Society (EWS) and Low Income Group (LIG), the requirements on planning, design of layouthhelter have
been rationalized and the same are provided in this Part. This will contribute significantly in the massive
housing programmed undertaken for the low income sector. This information is based on the provisions
of IS 8888 (Part 1) : 1993 ‘Guide for requirements of low income housing: Part 1 Urban areas (jirst revision)’.

Further, city development process would need a dynamic approach to take care of urban renewal and also
development needs in dense core areas of the cities. Innovative approaches in planning and design with participating
models of public private-people’s partnership become necessary to solve the emerging development needs. With

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 3


this in view, many city development agencies have evolved innovative planning and development tools like
transferable development rights (TDR) where the developer would receive a portion of the development rights in
a new location, keeping in view the constraints in the existing land area and the development potential. Such
development rights can be transferred into outskirts or new developed areas where land availability is assured.
This would encourage the professionals and developers to participate in urban renewal and at the same time
ensure that the developments in both the inner core areas and new areas take place in an orderly and efficient
manner. The TDR concept should be increasingly encouraged by the authority dealing with urban renewal, re-
development projects including housing and re-development projects for slum including dwellers.

Urbanization in India is taking place at a rapid pace. With 5 million population in cities at the time of independence,
it has already crossed 28 million (2001 census). It is likely to be 50 million by 2021. The number of cities and
towns have been expanding and there are 5161 cities and towns of various sizes. In the Indian practice cities
over 50 lakhs population have been identified as mega-cities (6 in number) and cities over 10 lakhs (29 in
number) population as metro-cities. These 35 cities above 10 lakhs population is likely to be above 70 by 2021.
The other cities are either small or medium towns or cities with different population limits. Urbanization in each
of above cities and towns (mega-cities, metro-cities, small and medium towns and cities) will be different in
nature and the development challenges are also different keeping in view the extent of urbanization,
industrialization, commercialization and the nature of transportation needs. Therefore, the Code provisions should
be appropriately utilized depending upon the need of hierarchy of cities for which the administrative and technical
requirements have been covered in the Code for various facets of the activity.

The first version of this Part was prepared in 1970. As a result of incorporation of this Part in the revised
development control rules and building byelaws of some municipal corporations and municipalities, some useful
suggestions had emerged. First revision of this part was brought out in. 1983, where these suggestions were
incorporated to the extent possible. The major modifications incorporated in the first revision included:

a) Addition of development control rules giving guidance on means of access, community spaces and
other aspects required for planning layouts.
b) Addition of provisions regarding plot sizes and frontage for different types of buildings, such as detached,
semi-detached, row type and special housing schemes.
c) Requirements of open spaces for other occupancies, such as educational, institutional, assembly, industrial
buildings, etc, were included.
d) Provisions relating to interior open space were elaborated, including requirements for ventilation shaft.
e) Requirements of open spaces for group housing development were covered.
f) Requirements of off-street parking spaces were covered.
g) Requirements for greenbelts and landscaping including norms for plantations of shrubs and trees were
covered.
h) Requirements of certain parts of buildings, such as loft, store room, garage, basement, chimney, parapet,
cabin, boundary wall, wells, septic tanks, office-cum-letter box room, meter room were included.
j) Special requirements of low income housing were covered.

The term Development Control Rules used in this Part encompasses the related aspects comprehensively with a
view to promoting orderly development of an area.

This second revision is being brought out to incorporate the modifications found necessary in light of the experience
gained with the use of this Part. Significant modifications incorporated in thk revi’sion include:

a) Terminology given in this Part has been made exhaustive by incorporating definitions of additional
terms used, such as, access, chimney, to erect, etc, and number of terms pertaining to cluster planning
for housing.
b) Detailed planning norms/open spaces for various amenities such as educational facilities, health care
facilities, socio-cultural facilities, distribution services, police, civil defence and home guards, and fire
services have been included.
c) Off-street parking requirements have now been also included for cities with population (i) between’
1000000 and 5000000, and (ii) above 5000000 (see Annex B).
d) Special requirements for low income housing given in the earlier version have been modified and
updated (see Annex C) based on IS 8888 (Part 1) : 1993 ‘Guide for requirements of low income housing:

4 NATIONAL BUILDING CODE OF INDIA


Part 1 Urban area (first revision)’. In these revised provisions, single room dwelling has been discouraged,
guidelines for water seal latrine have also been incorporated, and cluster planning approach has been
recommended.
e) Requirements for cluster planning for housing have been added (see Annex E), which are based on the
guidelines given in IS 13727:1993 ‘Guide for requirements of cluster planning for housing’.
f) Special requirements for low income housing for rural habitat planning has been added (see Annex F).
g) Special requirements for development planning in hilly areas has been added (see Annex G).
h) The requirements for buildings and facilities for the physically challenged have been revised, with
listing of additional categories of physically challenged; modifications in requirements of ramps, stairs,
doors, handrails and controls; and incorporation of additional requirements regarding windows.
j) Also, the opportunity has been utilized to update the reference to Indian Standards.

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 5


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 3 DEVELOPMENT CONTROL RULES AND
GENERAL BUILDING REQUIREMENTS

1 SCOPE 2.9 Building — Any structure for whatsoever purpose


and of whatsoever materials constructed and every part
This Part deals with the development control rules and
thereof whether used as human habitation or not and
general building requirements to ensure health and
includes foundation, plinth, walls, floors, roofs,
safety of the public.
chimneys, plumbing and building services, fixed
2 TERMINOLOGY platforms, VERANDAH, balcony, cornice or projection,
part of a building or anything affixed thereto or any
2.0 For the purpose of this part, the following
wall enclosing or intended to enclose any land or space
definitions shall apply:
and signs and outdoor display structures. Tents,
2.1 Access — A clear approach to a plot or a building. SHAMIANAHS, tarpaulin shelters, etc, erected for
2.2 Accessory Use — Any use of the premises temporary and ceremonial occasions with the permission
of the Authority shall not be considered as building.
subordinate to the principal use and customarily
incidental to the principal use. 2.10 Building, Height of — The vertical distance
,
measured in the case of flat roofs, from the average
2.3 Alteration — A change from one occupancy to
level of the ground around and contiguous to the
another, or a structural change, such as an addition to
building or as decided by the Authority to the terrace
the area or height, or the removal of part of a building,
of last livable floor of the building adjacent to the
or any change to the structure, such as the construction
external walls; and in the case of pitched roofs, up to
of, cutting into or removal of any wall, partition,
the point where the external surface of the outer wall
column, beam, joist, floor or other support, or a change
intersects the finished surface of the sloping root and
to or closing of any required means of ingress or egress
in the case of gables facing the road, the mid-point
or a change to the fixtures or equipment.
between the eaves level and the ridge. Architectural
2.4 Approved — Approved by the Authority having features serving no other function except that of
jurisdiction. decoration shall be excluded for the purpose of
measuring heights.
2.5 Authority Having Jurisdiction — The Authority
which has been created by a statute and which for the 2.11 Building Envelope — The horizontal spatial
purpose of administering the Code/Part may authorize limits up to which a building may be permitted to be
a committee or an official to act on its behalf; constructed on a plot.
hereinafter called the ‘Authority’.
2.12 Building Line — The lineup to which the plinth
2.6 Back-to-Back Cluster — Clusters when joined of a building adjoining a street or an extension of a
back to back and/or on sides (see Fig. 1). street or on a future street may lawfully extend. It
includes the lines prescribed, if any, in any scheme.
The building line may change from time-to-time as
decided by the Authority.
2.13 Cabin — A non-residential enclosure constructed
of non-load bearing partition.
— — 2.14 Canopy — A projection over any entrance.
2.15 Carpet Area — The covered area of the usable
rooms at any floor level (excluding the area of the wall).
2.16 CHtL4J.lA — A sloping or horizontal structural
overhang usually provided over openings on external
walls to provide protection from sun and rain.
FIG. 1 BACK-TO-BACKCLUSTER
2.17 Chimney — An upright shaft containing one or
2.7 Balcony — A horizontal projection, with a more flues provided for the conveyance to the outer
handrail or balustrade or a parapet, to serve as passage air of any product of combustion resulting from the
or sitting out place. operation of heat producing appliance or equipment
employing solid, liquid or gaseous fuel.
2.8 Basement or Cellar — The lower storey of a
building below or partly below ground level. 2.18 Chowk or Courtyard — A space permanently

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS ‘7


open to the sky, enclosed fully or partially by building direct access from the main room without any inter-
and may be at ground level or any other level within communicating door.
or adjacent to a building.
2.26 Cover&d Area — Ground area covered by the
2.19 Chowk, Inner — A chowk enclosed on all sides. building immediately above the plinth level. The area
covered by the following in the open spaces is excluded
2.20 Chowk, Outer — A chowk one of whose sides
from covered area (see Table 3):
is not enclosed.
a) Garden, rockery, well and well structures,
2.21 Closed Clusters — Clusters with only one
plant nursery, waterpool, swimming pool (if
common entry into cluster open space (see Fig. 2).
uncovered), platform round a tree, tank,
2.22 Cluster — Plots or dwelling units or housing fountain, bench, CFL4BUTfL4 with open top
grouped around an open space (see Fig. 3). and unenclosed on sides by walls and the like;
Ideally housing cluster should not be very large. In b) Drainage culvert, conduit, catch-pit, gully pit,
ground and one storeyed structures not more than 20 chamber, gutter and the like;
houses should be grouped in a cluster. Clusters with c) Compound wall, gate, unstoreyed porch and
more dwelling units will create problems in identity, portico, canopy, slide, swing, uncovered
encroachments and of maintenance. staircase, ramps areas covered by CHHAJJA
and the like; and
2.23 Cluster Court Town House — A dwelling in a
d) Watchmen’s booth, pumphouse, garbage
cluster plot having 100 percent or nearly 100 percent
shaft, electric cabin or sub-stations, and such
ground coverage with vertical expansion, generally
other utility structures meant for the services !---
limited to one floor only and meant for self use.
of the building under consideration.
2.24 Cluster Plot — Plot in a cluster.
NOTE — For the purpose of this Part, covered area
2.25 Cooking Alcove — A cooking space having equalsthe plot area minusthe area due for open spaces.

ONECOMMON
ENTRY

FIG. 2 CLOSEDCLUSTER

GROUP OPEN
SPACE INA CLUSTER
6 ,.
10 9 s 7
;~l
11

12

13 4

14 3
A
2
15 +7 18
16 1

FIG. 3 CLUSTER

8 NATIONAL BUILDING CODE OF INDIA


P-

2.27 ‘Cul-de-sac’ Cluster 2.34 Escalator — A power driven, inclined, continuous


stairway used for raising or lowering passengers.
Plots/dwelling units when located along a
pedestrianised or vehicular ‘cul-de-sac’ road (see 2.35 Exit — A passage, channel or means of egress
Fig. 4). from any building, storey or floor area to a street or
other open space of safety.

2,36 External Faces of Cluster — Building edges


facing the cluster open spaces.

2.37 Fire Separation — The distance in metres


measured from the external wall of the building
concerned to the external wall of any other building
on the site, or from other site, or from the opposite
side of a street or other public space for the purpose of
preventing the spread of fiie.

2.38 Floor — The lower surface in a storey on which


one normally walks in a building. The general term
‘floor’ unless specifically mentioned otherwise shall
not refer to a ‘mezzanine floor’.

2.39 Floor Area Ratio (FAR) — The quotient


obtained by dividing the total covered area (plinth area) ---
FIG. 4 CUL-DE-SAC CLUSTER on all floors by the area of the plot:
2.28 Density — The residential density expressed in
FM= Total covered area of the floors
terms of the number of dwelling units per hectare.
Plot area
NOTE — Where such densities are expressed exclusive of
communityfacilities and provision of open spaces and major 2.40 Gallery — An intermediate floor or platform
roads (excluding incidental open spaces), these will be net projecting from a wall of an auditorium or a hall
residentialdensities.Wherethesedensitiesare expressedtaking
into consideration the required open space provision and providing extra floor area, additional seating
community facilities and major roads, these would be gross accommodation, etc. It shall also include the structures
residential densities at neighborhood level, sector level or provided for seating in stadia.
town level, as the case may be. The provisionof open spaces
and community facilities will depend on the size of the 2.41 Garage, Private — A building or a portion
residential community. thereof designed and used for parking of private owned
Incidentalopen spaces are mainly open spaces required to be motor driven or other vehicles.
left around and in between two buildings to provide lighting
and ventilation. 2.42 Garage, Public — A building or portion thereof,
2.29 Detached Building — A building detached on other than a private garage, designed or used for
all sides. repairing, servicing, hiring, selling or storing or parking
motor driven or other vehicles.
2.30 Development — ‘Development’ with grammatical
variations means the carrying out of building, 2.43 Group Housing — Housing for more than one
engineering, mining or other operations, in, or over, dwelling unit, where land is owned jointly (as in the
or under land or water, on the making of any material case of co-operative societies or the public agencies,
change, in any building or land, or in the use of any such as local authorities or housing boards, etc) and
building, land, and includes re-development and layout the construction is underta$+n by one Agency.
and subdivision of any land and ‘to develop’ shall be 2.44 Group Open Space — Open space within a
construed accordingly. cluster.
2.31 Drain — A conduit, channel or pipe for the Group open pace is neither public open space nor
carriage of storm water, sewage, waste water or other private open space. Each dwelling unit around the
water borne wastes in a building drainage system. cluster open space have a share and right of use in it.
2.32 Drainage — The removal of any liquid by a The responsibility for maintenance of the same is to
system constructed for the purpose. be collectively shared by all the dwelling units around.

2.33 Dwelling Unit/Tenement — An independent 2.45 Habitable Room — A room occupied or


housing unit with separate facilities for living, cooking designed for occupancy by one or more persons for
and sanitary requirements. study, living, sleeping, eating, kitchen if it is used as a

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 9


living room, but not including bathrooms, water-closet 2.50 Lift — An appliance designed to transport
compartments, laundries, serving and store pantries, persons or materials between two or more levels in a
corridors, cellars, attics, and spaces that are not used vertical or substantially vertical direction by means of
frequently or during extended periods. a guided car or platform. The word ‘elevator’ is also
synonymously used for ‘lift’.
2.46 Independent Cluster — Clusters surrounded
from all sides by vehicular access roads and/or 2.51 Loft — A structure providing intermediate
pedestrian paths (see Fig. 5). storage space in between two floors with a maximum
height of 1.5 m, without having a permanent access.

2.52 Mezzanine Floor — An intermediate floor


between two floors of any storey forming an integral
part of floor below.

2.53 Occupancy or Use Group — The principal


occupancy for which a building or a part of a building
is used or intended to be used; for the purposes of
classification of a building according to occupancy;
an occupancy shall be deemed to include subsidiary
occupancies which are contingent upon it.

2.54 Occupancy, Mixed — The occupancy, where


more than one occupancy are present in different
FIG. 5 INDEPENDENT
CLUSTER portions of.the building.

2.55 Open Clusters — Cluster where cluster open


2.47 Interlocking Cluster —Clusters when joined
spaces are linked to forma continuous open space (see
at back andon sides with atleastone side of a cluster
Fig. 7).
common and having some dwelling units opening onto
or having access from the adjacent clusters. 2.56 Open Space — An area, forming an integral part
of the plot, left open to the sky.
Dwelling units in such clusters should have at least
two sides open to external open space. Houses in an NOTE — The open space shall be the minimum distance
interlocking cluster can have access, ventilation and measuredbetweenthe front, rear and side of the building and
the respectiveplot boundaries.
light from the adjacent cluster and should also cater
for future growth (see Fig. 6). 2.57 Open Space, Front — An open space across the
front of a plot between the building line and front
2.48 Internal Faces of Cluster — Building edges
boundary of the plot.
facing the adjacent cluster open space (as in case of
interlocking cluster) of the surrounding pedestrian 2.58 Open Space, Rear — An open space across the
paths or vehicular access roads. rear of a plot between the rear of the building and the
rear boundary of the plot.
2.49 Ledge or TAND — A shelf-like projection,
supported in any manner whatsoever, except by means 2.59 Open Space, Side — An open space across the
of vertical supports within a room itself but not having side of the plot between the side of the building and
projection wider than 1 m. the side boundary of tb plot.

FIG. 6 INTERLOCKING
CLUSTER

10 NATIONALBUILDINGCODE OF INDIA
FIG. 7 OPEN CLUSTER

2.60 Owuer-Person or bodyhaving a legal interest 2.70 Row Housing/Row Type Building — A row of
in land and/or building thereon. This includes free buildings, with only front, rear and interior open spaces
holders, leaseholders or those holding a sub-lease where applicable.
which both bestows a legal right to occupation and
2.71 Semi-Detached Building — A building detached
gives rise to liabilities in respect of safety or building
on three sides.
condition.
2.72 Service Roafiane — A roadllane provided
In case of lease or sub-lease holders, as far as ownership
adjacent to a plot(s) for access or service purposes as
with respect to the structure is concerned, the structure
the case may be.
of a flat or structure on a plot belongs to the allottee/
lessee till the allotmenflease subsists. 2.73 Set-Back Line — A line usually parallel to the
plot boundaries and laid down in each case by the
2.61 Parapet — A low wall or railing built along the Authority, beyond which nothing can be constructed
edge of a roof or floor. towards the plot boundaries.
2.62 Parking Space — An area enclosed or unenclosed, 2.74 Site (Plot) — A parcel (piece) of land enclosed
covered or open, sufficient in size to park vehicles, by definite boundaries.
together with a drive-way connecting the parking space
with a street or alley and permitting ingress and egress 2.75 Site, Corner — A site at the junctions of and
of the vehicles. fronting on two or more intersecting streets.

2.63 Partition — An interior non-load bearing barrier, 2.76 Site, Depth of — The mean horizontal distance
one storey or part-storey in height. between the front and rear site boundaries.

2.64 Plinth — The portion of a structure between the 2.77 Site, Double Frontage — A site, having a
surface of the surrounding ground and surface of the frontage on two streets, other than a comer plot.
floor, immediately above the ground. 2.78 Site, Interior or Tandem — A site access to
2.65 Plinth Area — The built up covered area which is by a passage from a street whether such
measured at the floor level of the basement or of any passage forms part of the site or not.
‘f
storey. 2.79 Staircover (or MUMTY) — A structure with a
2.66 Porch — A covered structure supported on roof over a staircase and its landing built to “enclose
pillars or otherwise for the purpose of pedestrian or only the stairs for the purpose of providing protection
vehicular approach to a building. from weather and not used for human habitation.

2.67 Road — See 2.82. 2.80 Storey — The portion of a building included
between the surface of any floor and the surface of the
2.68 Road Line — See 2.84. floor next above it, or if there be no floor above it,
then the space between any floor and the ceiling next
2.69 Room Height — The vertical distance measured
above it.
from the finished floor surface to the finished ceiling
surface. Where a finished ceiling is not provided, the 2.81 Storey, Topmost — The uppermost storey in a
underside of the joists or beams or tie beams shall building whether constructed wholly or partly on the
determine the upper point of measurement. roof.

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 11


2.82 Street — Any means of access, namely, 2.87 Tower-like Structures — Structures shall be
highway, street, lane, pathway, alley, stairway, deemed to be tower-like structures when the height of
passageway, carriageway, footway, square, place or the tower-like portion is at least twice the height of the
bridge, whether a thoroughfare or not, over which the broader base at ground level.
public have a right of passage or access or have passed
2.88 VERANDAH — A covered area with at least one
and had access uninterruptedly for a specified period,
side open to the outside with the exception of 1 m high
whether existing or proposed in any scheme, and
parapet on the upper floors to be provided on the open
includes all bunds, channels, ditches, storm-water
side.
drains, culverts, sidewrdks, traffic islands, roadside
trees and hedges, retaining walls, fences, barriers and 2.89 Volume to Plot Area Ratio (VPR) — The ratio
railings within the street lines. of volume of building ‘measured in cubic metres to the
area of the plot measured in square metres and
2.83 Street Level or Grade — The officially
expressed in metres.
established elevation or grade of the central line of the
street upon which a plot fronts and if there is no 2.90 Water-Closet (WC) — A water flushed
officially established grade, the existing grade of the plumbing fmture designed to receive human extirement
street at its mid-point. directly from the user of the fixture. The term is used
sometimes to designate the room or compartment in
2.84 Street Line — The line defining the side limits
which the fixture is placed.
of a street.
2.91 Window — An open@g to the outside other than
2.85 To Abut — To abut on a street boundary such
a door, which provides all or part of the required natural
that any portion of the building is on the road boundary.
light or ventilation or both to an interior space.
2.86 To Erect — To erect a building means:
3 LAND USE CLASSIFICATION AND USES
a) to erect a new building on any site whether PERMITTED
previously built upon or noc and
3.1 Land Use Classification
b) to re-erect any building of which portions
above the plinth level have been pull down, The land use classification may be as indicated
burnt or destroyed. below:

S1 No. Use Zbne (Level 1) Use Zone (Level 2)

(1) (2) (3)

i) Residential (R) Primary Residential Zone (R- 1)


Mixed Residential Zone (R-2)
Unplanned/Informal Residential Zone (R-3)

ii) Commercial (C) Retail Shopping Zone (C-1)


General Business and Commercial District/Centres (C-2)
Wholesale, Godowns, Warehousing/Regulated Markets (C-3) n
iii) Manufacturing (M) Service and Light Industry (M-1)
Extensive and Heavy Industry (M-2)
Special Industrial Zone Hazardous, Noxious and Chemical (M-3)

iv) Public and Semi-Public (PS) Government/Semi-Government/Public Off~es (PS- 1)


Government Land (use determined) (PS-2j ,,
Educational and Research (PS-3)
Medical and Health (PS-4)
Social, Cultural and Religious (PS-5)
Utilities and Services (PS-6)
Cremation and Burial Grounds (PS-7)

v) Recreational (P) Playgrounds/Stadium/Sports Complex (P-1)


Parks and Gardens — Public Open Spaces (P-2)
Special Recreational Zone — Restricted Open Spaces (P-3)
Multi-Open Space (Maidan) (P-4)

12 NATIONAL BUILDING CODE OF INDIA


S1 No. Use Zone (Level 1) Use Zbne (Level 2)

(1) (2) (3)

vi) Transportation and Roads (T-1)


Communication (T) Railways (T-2)
Airport (T-3)
Seaports and Dockyards (T-4)
Bus Depots/Truck Terminals and Freight Complexes (T-5)
Transmission and Communication (T-6)

vii) Agriculture and Water Bodies Agriculture (A-1)


Forest (A-2)
Poultry and Dairy Farming (A-3)
Rural Settlements (A-4)
Brick Kiln and Extractive Areas (A-5)
Water Bodies (A-6)

viii) Special Area Old Built-up (Core) Area (S-1)


Heritage and Conservation Areas (S-2)
Scenic Value Areas (S-3)
Village Settlement (S-4)
Other Uses (S-5)

NOTES
1 Areas of informal activities may be identified in the above land use categories at Level 2.
2 Mixed use zone may be identified at the development plan level, having more than one use zone with mixed activities of
such use zones.
3 In all, there could be 35 use zones at the development plan level within eight land use categories at the perspective plan
level as given in the above table.
4 Use premises for different activities could be provided at the project/action plan level or with the approval of the Authority
as the case may be.
5 Use zone regulations for the use permissibility could be decided by the town planner depending upon the requirement/
feasibility.

3.2 The various building uses and occupancies (see 7) 3.6 Fire Safety
permitted on the various zones shall be as given in the Buildings shall be so plapned, designed and constructed
Master Plan. as to ensure fire safety and this shall be done as per
3.3 Uses to be in Conformity with the Zone Part 4 ‘Fire and Life Safety’.

Where the use of buildings or premises is not 4 MEANS OF ACCESS


specifically designated on the Development Plan or in 4.1 Every building/plot shall abut on a public/private
the absence of Development Plan, shall be in means of access like streets/roads duly formed.
conformity with the zone in which they fall.
4.2 Every person who erects a building shall not at
3.4 Uses as Specifically Designated on Development any time erect or cause or permit to erect any building
Plan which in any way encroaches upon or diminishes the
area set apart as means of access required in the Code.
Where the use of a site is specifically designated on
No buildings shall be erected so as to deprive any other
the Development Plan, it shall be used only for the
building of the means of access.
purpose so designated.
-“4 4.3 Width of Means of Access
3.5 Non-conforming Uses
The residential plots shall abut on a public means of access
No plot shall be put to any use, occupancy or premises
like streeth-oad. Plots which do not abut on a streethoad
other than the uses identified in 3.1, except with the
shall abuthont on a means of access, the width and other
prior approval of the Authority. requirements of which shall be as given in Table 1.

PART 3 DEVELOPMENTCONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 13


‘“-”“r

Table 1 Width and Length of Means of Access 4.3.4 In the interest of general development of an area,
(Clause 4.3) the Authority may require the means of access to be of
larger width than that required under 4.3 and 4.3.1.
SI Width of Means Length of Means
No. of Access of Access 4.3.5 In existing built-up areas in the case of plots
m m facing streetimeans of access less than 4.5 m in width,
(1) (2) (3) the plot boundary shall be shifted to be away by 2.25 m
0 6.0 75 from the central line of the street/means of accessway
ii) 7.5 150 to give rise to a new streetimeans of accessway of 4.5 m
iii) 9.0 250
iv) 12.0 400 width.
v) 18.0 1000
vi) 24.0 above 1000 4.4 The means of access shall be levelled, metalled,
flagged, paved, sewered, drained, chanelled, lighted,
N~ — If the developmentis only on one side of the meansof laid with water supply line and provided with trees for
access,the prcacrihedwidthsmaybe mfuced by 1m in eachcase.
shade to the satisfaction of the Authority free of
In no case, development on plots shall be permitted encroachment by any structure or fixture so as not to i
unless it is accessible by a public street of width not reduce its width below the minimum required under 4.3
less than 6 m. and shall be maintained in a condition to the satisfaction
of the Authority.
4.3.1 Other Buildings
4.4.1 If any private street or any other means of access
For all industrial buildings, theatres, cinema houses, to a building is not levelled, metalled, flagged or paved,
assembly halls, stadia, educational buildings, markets, sewed drained, channeled, lighted or laid with water .-
other buildings which attract large crowd, the means supply line or provided with trees for shade to the
of access shall not be less than the following: satisfaction of the Authority, who may, with the sanction
of the Authority, by written notice require the owner or
Width of Means of Length of Means owners of the several premises fronting or adjoining the
Access of Access said street or other means of access or abutting thereon
m m or to which access is obtained through such street or
12.0 200 other means of access or which shall benefit by works
15.0 400 executed, to carry out any or more of the aforesaid
18.0 600 requirements in such manner as he shall direct.
24.0 above 600
4.4.2 If any structure or fixture is set upon a means of
Further, in no case shall the means of access be lesser access so as to reduce its width below the minimum
in width than the internal accessways in layouts and required, the Authority may remove the same further
subdivision. and recover the expenses so incurred from the owner.

4.3.2 Pathways 4.5 Access from Highways/Important Roads


The approach to the buildings from road/street/internal No premises other than highway amenities like petrol
means of access shall be through paved pathway of pumps, motels, etc, shall have an access direct from
width not less than 1.5 m, provided its length is not highways and such other roads not less than 52 m in
more than 30 m. width, which the Authority with the approval of the
4.3.2.1 In the case of special housing schemes for low Highway Authority shall specify from time-to-time.
income group and economically weaker section of The Authority shall m@ntain a register of such roads
society developed up to two storeyed rowlcluster which shall be open tozpublic inspection at rdl times
housing scheme, the pedestrian pathway width shall during ot%ce hours. The portion of such roads on which
be 3 m subject to provisions of 9.4.l(a). The pedestrian direct access may be permitted shall be as identified in
pathway shall not serve more than 8 plots on each side the Development Plan. However, in the case of existing .5

of the pathway; the length of the pathway shall be not development on highways/other roads referred to
more than 50 m. above, the operation of this clause shall be exempted.
These provisions shall, however, be subject to the
4.3.3 The length of the main means of access shall provisions of the relevant State Highway Act, and
be determined by the distance from the farthest plot National Highway Act.
(building) to the public street. The length of the
subsidiary accessway shall be measured from the 4.6 For high rise buildings and buildings other than
point of its origin to the next wider road on which it residential, the following additional provisions of
meets. means of access shall be ensured:

14 NATIONAL BUILDING CODE OF fNDfA


a) The width of the main street on which the catering to the needs of area of layout, population for
building abuts shall not be less than 12 m and which the layout is planned and the category of
one end of this street shall join another street dwelling units. The following minimum provision shall
not less than 12 m in width; be made:
b) The approach to the building and open spaces a) 15 percent of the area of the layout, or
on all its sides up to 6 m width and the layout
b) 0.3 to 0.4’ ha/1 000 persons; for low income
for the same shall be done in consultation with
housing the open spaces shall be 0.3 ha/1 000
the Chief Fire Officer of the city and the same
persons.
shall be hard surface capable of taking the
mass of fire engine, weighing up to 45 tonnes. 5.2 No recreational space shall generally be less than
The said open space shall be kept free of 450 mz.
obstructions and shall be motorable.
5.2.1 The minimum average dimension of such
c) The main entrance to the plot shall be of
recreational space shall be not less than 7.5 m; if the
adequate width to allow easy access to the fire average width of such recreational space is less than
engine and in no case shall it measure less than 24 m, the length thereof shall not exceed 2.5 times
6 m. The entrance gate shall fold back against the average width. However, depending on the
the compound wall of the premises, thus configuration of the site, commonly open spaces of
leaving the exterior accessway within the plot
different shapes may be permitted by the Authority, as
free for movement of fire service vehicle. If long as the open spaces provided serve the needs of the
the main entrance at the boundm-y wall is built immediate community contiguous to the open spaces.
over, the minimum clearance shall be 4.5 m.
A turning radius of 9 m shall be provided for 5.2.2 In such recreational spaces, a single storeyed
fire tender movement. structure as pavilion or gymnasia up to 25 m2 in area
may be permitted; such area may be excluded from
4.7 Cul-de-sacs giving access to plots and extending FAR calculations.
from 150 m to 275 m in length with an additional
turning space at 150 m will be allowed only in 5.3 Each recreational area and the structure on it shall
residential areas, provided cul-de-sacs would be have an independent means of access. Independent
permissible only on straight roads and further provided means of access may not be insisted upon if
the end of cul-de-sacs shall be higher in level than the recreational space is approachable directly from every
level of the starting point of such dead end road. The building in the layout. Further, the building line shall
turning space, in this case shall be not less than 81 m2 beat least 3 m away from the boundary of recreational
in area, with no dimension less than 9 m. open space.

4.8 Intersection of Roads 5.4 Industrial Zones

For intersection junctions of roads meeting at right In the case of sub-division of land in industrial zones
angles as well as other than right angles, the rounding of area 0.8 hectare or more, 5 percent of the total area
off or cut off or splay or similar treatment shall be shall be reserved as amenity open space which shall
done, to the approval of the Authority, depending upon also serve as a general parking space; when such
the width of roads, the traffic generated, the sighting amenity open space exceeds 1500 m2, the excess area
angle, etc, to provide clear sight distance. could be utilized for the construction of buildings for
banks, canteens, welfare centres and such other
4.9 The building line shall be set back at least 3 m common purposes considered necessary for the
from internal means of access in a layout of buildings industrial user, as approved by the Authority.
in a plot subject to provisions of 8.2.1.
5.4.1 In all industrial plots measuring 1000 m2 or more
5 COMMUNITY OPEN SPACES AND AMENITIES in area, 10 percent of the total area shall be provided as
an amenity open spacetoamaximumof2500 m2. Such
5.1 Residential and Commercial Zones an amenity open space shall have a means of access and
In any layout or sub-division of land measuring 0.3 shall be so located that it could be conveniently utilized
hectare of more in residential and commercial zones, as such by the persons working in the industry.
the community open spaces shall be reserved for 5.5 Other Amenities
recreational purposes which shall as far as possible be
In addition to community open spaces, the layouts shall
provided in one place or planned out for the use of the
provide for the amenities as given in 5.5.1 to 5.5.6.
community in clusters or pockets.
These provisions may be modified based on specific
5.1.1 The community open spaces shall be provided requirements, as decided by the Authority.

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 15


5

Land Area Required, Min


c) Technical Education
1) Technical education centre (A) (1 for every 1000000 population to include 1 IT1 and
1 polytechnic)
i) Strength of ITI — 400 students
ii) Strength of polytechnic — 500 students
iii) Area per technical education centre 4.00 ha
a) Area for ITI 1.60 ha
b) Area for polytechnic 2.40 ha
2) Technical education centre (B) (1 for every 1000000 population to include 1 ITI,
1 technical centre and 1 coaching centre)
Area per technical education centre 4.00 ha
a) Area for ITI 1.60 ha
b) Area for technical centre 2.10 ha
c) Area for coaching centre 0.30 ha

d) Professional Education
1) Engineering college (1 for every 1000000 population)
i) Strength of the college — 1500 students
ii) Area per college 6.00 ha
2) Medical college (1 for every 1000000 population)
Area of site including space for general hospital 15.00 ha
3) Other professional colleges (1 for every 1000000 population)
i) Area of site for students strength upto 250 students 2.00 ha
ii) Additional area of site for every addhional 100 students or part thereof upto
total strength of 1000 students 0.50 ha
iii) Area of site for strength of college — From 1000 to 1500 students 6.00 ha

5.5.2 Health Care Facilities

Land Area Required, Min


1) Dispensary (1 for every 15000 population)
Area 0.08 ha to 0.12 ha
2) Nursing home, child we~are and maternity centre (1 for every 45000 to
100000 population)
i) Capacity 25 to 30 beds
ii) Area 0.20 ha to 0.30 ha
3) Poly-clinic with some observation beds (1 for every 100000 population)
Area 0.20 ha to 0.30 ha
4) Intemdiate hospital (category B) (1 for every 100000 population)
i) Capacity 80 beds (initially the provision may be for 50 including 20 maternity
beds)
ii) Total area 1.00 ha
a) Area for hospital 0.60 ha
b) Area for residential accommodation 0.40 ha
5) Intermediate hospital (catego~ A) (1 for every 100000 population)
i) Capacity 200 beds (initially the provision maybe for 100 beds)
ii) Total area 3.70 ha
a) Area for hospital 2.70 ha
b) Area for residential accommodation 1.00 ha

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 17


Land Area Required, Min
6) General hospital (1 for every 250000 population)
i) Capacity 500 beds (initially the provision maybe for 300 beds)
ii) Total area 6.00 ha
a) Area for hospital 4.00 ha
b) Area for residential accommodation 2.00 ha
7) Multi-speciality hospital (1 for 100000 population)
i) Capacity 200 beds (initially the provision maybe for 100 beds)
ii) Total area 9.00 ha
a) Area for hospital 6.00 ha
b) Area for residential accommodation 3.00 ha
8) Speciality hospital (1 for every 100000 population)
i) Capacity 200 beds (initially the provision maybe for 100 beds)
ii) Total area 3.70 ha
a) Area for hospital 2.70 ha
b) Area for residential accommodation 1.00 ha

5.5.3 SociOcultural facilities

Land Area Required, Min


1) Community room (1 for every 5000 population)
Area 750 mz
2) Communi~ hall, mangal karyayal&alyana mandapaw%arat gharAibraq
(1 for eve~ 15000 population)
Area 2000m2
3) Recreational club (1 for every 100000 population) (see also 5.2,5.2.1,5.2.2 and 5.3)
Area 10000 mz
4) Music, dance and drama centre (1 for every 100000 population)
Area 1000 mz
5) Meditation and spiritual centre (1 for every 100000 population)
Area 5000 mz
6) Socio-cultural centre (1 for every 1000000 population)
Area 15 ha

5.5.4 Distribution Services

Land Area Required, Min


1) Petrol/diesel jilling and servicing centre
May be permitted in central as well as sub-central business district, district centres,
community centres (only filling station), residential and industrial use zones in urban
areas, along the national highways, state highways, villages identified as growth centres,
freight complex and on proposed major roads.
Shall not be located on the road having right of way less than 30 m.
Shall be approved by the explosive/fire department.
ArealSize
i) only filling station 30mx17m
ii) Filling-cum-service station 36mx30m
iii) Filing-cum-service station-cum-workshop 45mx36m
iv) Filling station only for two and three wheelers 18mx15m
2) Compressed natural gas (CNG)/@ling centre
Permitted in all use zones (except in regional parks and Developed District Parks) and
along the national highways, state highways and villages identified as growth centres,
freight complex and on proposed major roads

18 NATIONAL BUILDING CODE OF INDIA


Lund Area Required, Min
Shall not be located on the road having right of way less than 30 m.
Shall be approved by the explosive/fire department.
Area/size for mother station (building component---control room/office/dispensing 1080 m2
room, store, pantry and W.C. (36 m x 30 m)
3) LPG godowns/Gas godown 1 for every 40000 to 50000 population
The major concern for its storage and distribution is the location which shall be away
from the residential areas and shall have open spaces all around as per the Explosive
Rules.
i) Capacity — 500 cylindersor8000 kg of LPG 520 m2
ii) Area (inclusive of chowkidar hut) (26 m x 20 m)
4) Milk distribution (1 milk booth for every 5000 population)
Area inclusive of service area 150 m2

5.5.5 Police, Civil Defence and Home Guards

Land Area Required, Min


1) Police station (1 for every 90000 population)
Area (inclusive of essential residential accommodation 0.05 ha additional to be 1.50 ha
provided for civil defence and home guards)
2) Police post (1 for every 40000 to 50000 population) (not served by a police station)
Area (inclusive of essential residential accommodation) 0.16 ha
3) District office and battalion (1 for every 1000000 population)
i) Area for district office 0.80 ha
ii) Area for battalion 4.00 ha
iii) Total area 4.80 ha
4) Police line (1 for every 2000000 population)
Area 4.00’to 6.00 ha
5) District Jail (1 for every 1000000 population)
Area 10.00 ha
6) Civil defence and home guards (1 for every 1000000 population)
Area 2.00 ha

5.5.6 Fire

Land Area Required, Min


One fire station or sub-fire station within 1 km to 3 km @or every 200000 population)
i) Area for fire station with essential residential accommodation 1.00 ha
ii) Area for sub-fire station with essential residential accommodation 0.60 ha

5.5.7 Telephone, Telegraphs, Postal and Banking Facilities

Land Area Required, Min

a) Telephone and Telegraphs

1) Telephone exchange of 40000 lines (1 for every 400000 population)


Area 4.00 ha
2] Telegraph booking counter (1 for eve~ 100000 population)
Floor area to be provided in community centre 200 m2
3) Telegraph booking and delivery ofice (1 for every 500000 population)
Floor area to be provided in district centres 1700 m2

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 19


Land Area Required, Min
b) Postal
1) Post ofice counter without delive~ (1 for every 15000 population)
Floor area to be provided in local shopping centre 85 m2 /
2) Head post ojlice with delivery ofice (1 for 250000 population)
Area 750 m2
3) Head post ofice and administrative ofice (1 for 500000 population)
Area 2500 mz .

c) Banking
1) Extension counters with ATM facility (1 for every 15000 population)
i) Floor area for counters 75 m2
ii) Floor area for ATM 6 m2
2) Bank with locker, ATM and other banking facilities (1 for 100000 population)
Area 2500 m2

5.5.8 Sports Activity

Land Area Required, Min


.-
1) Divisional sports centre (1 for 1000000 population)
Area 20.00 ha
2) District sport centre (1 for 100000 population)
Area 8.00 ha
3) Neighborhood play area (1 for 15000 population)
Area 1.50 ha
4) Residential unit play area (1 for 5000 population)
Area 5000m2

5.5.9 Shopping

Land Area Required, Min


1) Convenience shopping (1 for 5000 population)
Area 1500 m2
2) Local shopping including service centre (1 for 15000 population)
Area 4600 m2
3) Community centre with service centre (1 for 100000 population)
Area 5.00 ha
4) District centre (1 at district level/1 for 500000 population)
Area 7.50 ha
5) Local wholesale market (1 for 1000000 population)
Area 10.00 ha
6) Weekly markets (1 to 2 locations for every 100000 populations with 300 to 400 units per
location)
Parking and other open spaces within the commercial centres could be so designed that
weekly markets can operate in these areas during non-working hours.
The area of informal sector should have suitable public conveniences and solid waste
disposal arrangements.
Area per location 0.40 ha
7) Organized informal sector eating places (1 for 100000 population)
Area 2000m2

20 NATIONAL BUILDING CODE OF INDIA


5.5.10 Religious

Lund Area Required, Min


1) Religious campus (1 for 100000 population)
Area 5.00 ha

5.5.11 Electrical Sub-station

Lund Area Required, Min


1) 11 kV Sub-station (1 for 15000 population)
Area 500 11#
2) 66 kV Sub-station (2 for 100000 population)
Area for each Sub-station 6000m2
(that is 60 m x 100 m)
3) 220 kV Sub-station (1 for 500000 population)
Area 4.00 ha

5.5.12 Transport

Lund Area Required, Min


1) Three wheeler and taxi stand (1 for 15000 population)
Area 500 m2
2) Bus terminal (1 for 100000 population)
Area 4000m2
3) Bus depot (1 for 500000 population)
Area 2.00 ha

5.5.13 Cremation/.Burial Ground

The site shall be identified in locations, which are not proximous to residential areas

Land Area Required, Min


1) Electric crematorium (1 for large size towns)
Area 2.00 ha
2) Cremation ground (1 for 500000 population)
Area 2.50 ha
3) Burial ground (1 for 500000 population)
Area 4.00 ha

5.5.14 Dhobi Ghat

Land Area Required, Min


1) Dhobi ghat with appropriate arrangements for water and drainage facilities’
and it shall be ensured that the water bodies are not polluted as a result of
such activities (1 for 100000 population)
Area 5000m2

5.6 Every layout or sub-division shall take into account 6 REQUIREMENTS OF PLOTS
the provisions of development plan and if the land is 6.1 No building shall be constructed on any site, on
affected by any reservation for public purposes, the any part of which there is deposited refuse, excreta or
Authority may agree to adjust the location of such other offensive matter objectionable to the Authority,
reservations to suit the development. until such refuse has been removed therefrom and the

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 21


I

site has been prepared or left in a manner suitable for corresponding to the type of development as given
building purposes to the satisfaction to the Authority. below:

6.2 Damp Sites Type of Development Plot Size Frontage


Wherever the dampness of a site or the nature of the m2 m
soil renders such precautions necessary, the ground
(1) (2) (3)
surface of the site between the walls of any building
erected thereon shall be rendered damp-proof to the Detached building Above 250 Above 12
satisfaction of the Authority. Semi-detached building 125-250 8 to 12
6.3 Surface Water Drains Row type building 50-125 4.5 to 8

Any land passage or other area within the curtilage of NOTE — For low incomehousingsee 12.20.
a building shall be effectively drained by surface water
drains or other means. 6.6.1.1 The minimum size of the site for group housing
6.3.1 The written approval of the Authority shall be development shall be as given in the Master Plan and
obtained for connecting any sub-soil or surface water local development control rules.
drain to a sewer. 6.6.2 Industrial
6.4 Distance from Electric Lines The size of the plot shall not be less than 300 m2 and
No VERANDAH, balcony, or the like shall be allowed its width shall not be less than 15 m.
to be erected or re-erected or any additions or alterations
6.6.3 Other Land Uses
made to a building within the distances quoted below in
accordance with the current Indian Electricity Rules as The minimum size of plots for buildings for other uses
amended from time-to-time between the building and not covered under 5.5 shall be as decided by the
any overhead electric supply line: Authority.

Vertically Horizontally 7 CLASSIFICATION OF BUILDINGS


m m
7.0 Buildings are classified based on occupancy and
(1) (2) (3) (4)
types of construction.
a) Low and medium 2.5 1.2
7.1 For the purpose of the Code, the following
voltage lines and
shall be the occupancy classification and types of
service lines
construction; for more detailed information, reference
b) High voltage lines up 3.7 1.2
may be made to Part 4 ‘Fire and Life Safety’.
to and including
11 OOOV 7.1.1 Occupancy Class#ication
c) High voltage lines 3.7 2.0
a) Residential;
above 11 000 V and
b) Educational;
up to and including
33000 v c) Institutional;
d) Extra high voltage 3.7 2.0 d) Assembly;
line beyond 33000 V (plus 0.3 m (plus 0.3 m e) Business;
for every for every f) Mercantile (will include both retail and
additional additional wholesale stores);
33000 v 33000 v !3) Industrial (will itilude low, moderate and
or part or part high fire hazards);
thereof) thereof)
h) Storage; and
j) Hazardous.
6.5 Distance of site from the normal edge of water
courselarea maybe specified by the Authority, keeping 7.1.2 Types of Construction
in view the normal maximum floodhide level.
a) Type 1,
6.6 Size of Plots
b) Type 2,
6.6.1 Residential c) Type 3, and
Each plot shall have a minimum size/frontage d) Type 4.

22 NATIONAL BUJLDING CODE OF INDIA


F

8 OPEN SPACES (WITHIN A PLOT) beat least 5 m from the centre line of the street
(see 4.3.5).
8.1 General
NOTE — This limiting distance has to be determined
Every room intended for hum’an habitation shall abut by the Authorityfor individualroad/streetwidthstaking
on an interior or exterior open space or an open into accountthe traffic flow.
VERANDAH open to such interior or exterior open
8.2.1.2 Rear open space
space.
a) Every residential building shall have a rear
8.1.1 The open spaces inside and around a building
open space, forming an integral part of the
have essentially to cater for the lighting and ventilation
site, of an average width of 3 m and at no
requirements of the rooms abutting such open spaces,
place measuring less than 1.8 m, except that
and in the case of buildings abutting on streets in the
in the case of a back-to-back sites, the width
front, rear or sides, the open spaces provided shall be
of the rear open space shall be 3 m throughout.
sufficient for the future widening of such streets.
Subject to the condition of free ventilation,
8.1.2 Open Spaces Separate for each Building or Wing the open space left up to half the width of the
plot shall also be taken into account for
The open spaces shall be separate or distinct for each
calculating the average width of the rear open
building and where a building has two or more wings,
space. For plots of depths less than 9 m, for
each wing shall have separate or distinct open spaces
buildings up to 7 m in height, the rear open
for the purposes of lighting and ventilation of the wings.
space may be reduced to 1.5 m.
However, separation between accessory and main b) Rear open space to extend the rear wall
buildings more than 7 m in height shall not be less The rear open space shall be co-extensive with
than 1.5 m; for buildings up to 7 m in height no such the entire face of the rear wall. If a building
separation shall be required. abuts on two or more streets, such rear open
8.1.3 The open space shall be the minimum distance space shall be provided throughout the face
measured between the front, rear and side of the of the rear wall. Such rear wall shall be the
building and the respective plot boundaries. The front, wall on the opposite side of the face of the
rear and side of the building shall be the point of the building abutting on the wider street unless
building nearest to the boundary. the Authority directs otherwise.
c) In case of corner plots less than 300 mz in
8.2 Residential Buildings area, the rear open space should be 2.4 m
8.2.1 Exterior Open Spaces minimum.

8.2.1.1 Front open space 8.2.1.3 Side open space

a) Every building fronting a street shall have a a) Every semi-detached and detached building
front space, forming an integral part of the shall have a permanently open air space,
site as below: forming an integral part of the site as below:
1) For detached buildings there shall be a
sl Front Open Space, Width of Street minimum side open space of 3 m on both
No. A4in Fronting the Plot the sides.
NOTE — For detached residential buildlngs up
(1) (:) (:) in heighton plots with a frontageless than
to 7 m
12m (see 6.61), one of the side open spaces may
i) 1.51) up to 7.5’) be reduced to J.5 m.
ii) 3.0 7.5 to 18 2) For semi-detached buildings, there shall
iii) 4.5 18t030
be a minimum side open space of 3 m on
iv) 6.0 Above 30
one side.
I) For buildl~gs Up to a maximumheight 7 m. NOTE— For semi-detachedbuildingsup to 7 m
in height on plots with a frontage less than 9 m
NOTE — In case a building abuts two or more streets, the (see 6.6.1), the side open spaces may be reduced
value of open paces is to be based on the average width of to 1.5 m.
streets, subject to a minimum of 1.8 m for cases (ii), (iii) and
(iv) above.
3) For row-type buildings, no side open is
required.
b) For streets less than 7.5 m in width, the b) In the case of semi-detached buildings, the
distance of the building (building line) shall open spaces provided on one side shall be as

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 23


in 8.2.1.3 (a) and all habitable rooms shall d) The deficiency in the open spaces shall be
abut either on this side open space or front made good to satisfy 8.2.3.1 through the set-
and rear open spaces or an interior open space backs at the upper levels; these set-backs shall
(see 8.2.5). not be accessible from individual rooms/flats
at these levels.
8.2.2 The provisions of 8.2.1.2 and 8.2.1.3 are not
applicable to parking lock-up garages up to 3 m in 8.2.4 The front open space would govern the height
height located at adistanceof 7.5 mfrom any street of the building (see 9.4).
line or front boundary of the plot. 8.2.5 Interior Open Spaces
8.2.3 The open spaces mentioned in 8.2.1.1 to 8.2.1.3 a) Inner courtyard — In case the whole of one
shall be for residential buildings up to a height of 10 m. side of every room excepting bath, WC and
8.2.3.1 For buildings of height above 10 m, the open store room is not abutting on either the front,
spaces (side and rear) shall be as given in Table 2. The rear or side open spaces, it shall abut on an
front open spaces for increasing heights of buildings inner courtyard, whose minimum width shall
shall be governed by 9.4.1 (a). be 3 m.
Further, the inner courtyard shall have an area,
Table 2 Side and Rear Open Spaces for Different .
throughout its height, of not less than the
Heights of Buildings square of one-fifth the height of the highest
(Clause 8.2.3.1) wall abutting the courtyard. Provided that
when any room (excluding staircase bay,
sl Height of Side and Rear Open Spaces to
Buildings be Left Around Building
bathroom and water-closet) is dependent for
No.
m its light and ventilation on an inner courtyard,
(1) (2) (:) the dimension shall be such as is required for
each wing of the building.
O 10 3
ii) 15 5 Where only water-closet and bath room are
iii) 18 6 abutting on the interior courtyard, the size of
iv) 21 7 the intenor courtyard shall be in line with the
v) 24 8
vi) 27 9 provision for ventilation shaft as given
vii) 30 10 in 8.2.5 (b).
viii) 35 11 b) Ventilation shajl — For ventilating the spaces
ix) 40 12
@ 45 13 for water-closets and bath rooms, if not
xi) 50 14 opening on to front, side, rear and interior
xii) 55 and above 16 open spaces, these shall open on the
ventilation shaft, the size of which shall not
NOTES
be less than the values given below:
1 For buildings above 24 m in height, there shall be a minimum
front open space of 6 m.
Height of Size of Minimum
2 Where rooms do not derive light and ventilation from the
exterior open space, the width of such exterior open space as Buildings Ventilation One Dimension of
given in CO13 maybe reduced by 1 m subject to a minimum of Shafi the Sh@
3 m and a maximum of 8 m. No further projections shall be
m’
permitted.
3 If the length or depth of the building exceeds 40 m, add
(?) (2) (;)
to CO1 (3) 10 percent of length or depth of building minus
up to 10 1.2 0.9
4.0 m.
12 2.8 1.2
18 4.0 1.5
8.2.3.2 For tower-like structures, as an alternative 24 5.4 1.8
to 8.2.3.1, open spaces shall be as below: 30 8.0 2.4
Above 30 9.0 3.0
a) Up to a height of 24 m, with one set-back, the
open spaces at the ground level, shall be not NOTES
less than 6 m; 1 For buikthgs of height above 30 m, a mechanical ventilation
system shall be installed besides the provision of minimum
b) For heights between 24 m and 37.5 m with
ventilation shaft.
one set-back, the open spaces at the ground
2 For fully air-conditioned residential buildings for lodging
level, shall be not less than 9 m; purposes, the ventilation shaft need not be insisted upon,
c) For heights above 37.5 m with two set-backs, provided the air-conditioning system works in an uninterrupted
manner, also, provided there is an alternative source of power
the open spaces at the ground level, shall be
supply.
not less than 12 m; and

24 NATIONAL BUILDING CODE OF INDIA


c) Outer courtyard — The minimum width of shops line zone the open spaces may be
the outer courtyard (as distinguished from its relaxed.
depth) shall be not less than 2.4 m. If the width e) Industrial buildings — The open spaces
of the outer courtyard is less than 2.4 m, it around the building shall be not less than
shall be treated as a notch and the provisions 4.5 m for heights up to 16 m, with art increase
of outer courtyard shall not apply. However, of the open spaces of 0.25 m for every
if the depth of the outer courtyard is more than increase of 1 m or fraction thereof in height
the width, the provisions of 8.1.2 shall apply above 16 m.
for the open spaces to be left between the NOTE — Special rules for narrow industrial plots in
wings. the city, namely plots less than 15 m in width, and with
appropriate set-backs from certain streets and highways,
8.2.6 Joint Open Air Space shall I_reapplicable.

Every such interior or exterior open air space, unless f) Hazardous occupancies — The open spaces
the latter is a street, shall be maintained for the benefit around the building shall be as specified for
of such building exclusively and shall be entirely within industrial buildings [see 8.3.1 (e)].
the owner’s own premises.
8.4 Exemption to Open Spaces
8.2.6.1 If such interior or exterior open air space is
8.4.1 Projections into Open Spaces
intended to be used for the benefit of more than one
building belonging to the same owner, the width of Every open space provided either interior or exterior
such open air space shall be the one specified for the shall be kept free from any erection thereon and shall
tallest building as specified in 8.2.3 abutting on such be open to the sky, except as below:
open air space.
a) Cornice, roof or weather shade not more than
8.2.6.2 If such interior or exterior open air space is 0.75 m wide;
jointly owned by more than one person, its width shall b) Sunshades over windows/ventilators or other
also be as specified in 8.2, provided every such person openings not more than 0.75 m wide; ~
agrees in writing to allow his portion of such joint open
c) Canopy not to be used as a sit out with
air space to be used for the benefit of every building
clearance of 1.5 m between the plot boundary
abutting on such joint open air space and provided he
and the canopy;
sends such written consent to the Authority for record,
d) Projected balcony at higher floors of width
Such common open air space shall thenceforth be
not more than 1.2 m; and
treated as a permanently open air space required for
the purposes of the Code. No boundary wall between e) Projecting rooms/balconies [see (d)] at
such joint open air space shall be erected or raised to a alternate floors such that rooms of the lower
height of more than 2.0 m. two floors get light and air and the projection
being not more than the height of the storey
8.3 Other Occupancies immediately below.
8.3.1 Open spaces for other occupancies shall be as However, these projections into open spaces shall not
below: reduce the minimum required open spaces.
a) Educational buildings — Except for nursery 8.4.1.1 Accessory building
schools, the open spaces around the building
The following accessory buildings may be permitted
shall be not less than 6 m.
in the open spaces:
b) Institutional buildings — The open spaces
around the building shall be not less than 6 m. a) In an existing building, sanitary block of
2.4 m in height subject to a maximum of 4 mz
c) Assembly buildings — The open space at front
in the rear open space at a distance of 1.5 m
shall be not less than 12 m and the other open
from the rear boundary may be permitted,
spaces around the building shall be not less
where facilities are not adequate.
than 6 m.
b) Parking lock up garages not exceeding 2.4 m
NOTE — However, if assembly buildings are permitted
in purely residential zones, the open spaces around the in height shall be permitted in the side or
building shrdl be not less than 12 m. rear open spaces at a distance of 7.5 m from
d) Business, mercantile and storage buildings — any road line or the front boundary of the plot;
The open spaces around the building shall be and
not less than 4.5 m. Where these occur in a c) Suction tank and pump room each up to
purely residential zone or in a residential with 2.5 mz in area,

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 25


8.4.2 Projection into Street 8.5.2 Additions or Extensions to a Building

8.4.2.1 In existing built-up or congested areas, no Additions or extensions to a building shall be allowed,
projection of any sort whatsoever, except sunshades provided the open spaces for the additionslextensions
(see 8.4.2.3) extending more than 23 crn below a height satisfy 8.2 after such additions/extensions are made.
of4.3 m, shall project over theroad orover any drain
or over any portion outside the boundaries of the site, 9 AREA AND HEIGHT LIMITATIONS
provided the projection arising out of the vertical part 9.1 General
of the rain-water spouts projecting at the road level or
the water pipe may be permitted in accordance with The limitation of area and height of buildings of
the drainage plan. different occupancy classes and types of construction
shall be achieved by specifying it in terms of FAR,
8.4.2.2 Porticos in existing developed area which shall take into account the various aspects that
Porticos in bazaar areas of existing developed areas govern in specifying FAR as given below:
may be permitted to project on road land subject to the a) Occupancy class;
following limitations:
b) Types of construction;
a) Porticos may be allowed on such roads c) Width of street fronting the building and the
leaving a minimum clear space of 18 m traffic load;
between kerbs; d) Locality where the building is proposed and
b) The porticos shall not be less than 3 m wide; the density;
c) Nothing shall be allowed to be constructed e) Parking facilities;
on the portico which shall be used as an open f) Local fire fighting facilities; and
terrace;
g) Water supply and drainage facilities.
d) Nothing shall be allowed to project beyond
the line of arcades; and 9.2 The comparative FAR’s for different occupancies
e) The space under the portico shall be paved and types of construction are as given in Table 3 and
and channeled according to the directions of the Authority shall select a basic FAR for one
the Authority. occupancy and a type of construction and arrive at the
FAR values for other combinations taking into account
8.4.2.3 Sunshades over windows and ventilators the other local factors (see 9.1).
Projections of sunshades over windows or ventilators 9.2.1 Unlimited Areas
in existing built-up or congested areas when permitted
by the Authority shall fulfil the following conditions: The minimum fiie separation on all sides of buildings
of unlimited areas (see Table 3) and of Type, 1
a) No sunshade shall be permitted over the road construction shall be 9 m.
or over any drain or over any portion outside
the boundaries of the site below a height of 9.3 Street Width
2.8 m from the road level;
The area limits shall apply to all buildings fronting on
b) Sunshades provided above a height of 2.8 m a street or public space not less than 9 m in width
from the ground level shall be permitted to accessible to a public street.
project up to a maximum width of 60 cm, if
the road over which they project exceeds 9 m 9.4 Height Limit
in width; and The height and number of storeys shall be related to
c) No sunshade shall be permitted on roads less FAR and the provisions of 8.
than 9 m in width or on roads having no
9.4.1 Where a building height is not covered by
footpaths.
Table 3, the maximum height shall be limited
8.5 Limitations to Open Spaces according to the width of the street as follows:

8.5.1 Safeguard Against Reduction of Open Space a) The maximum height of building shall not
No construction work on a building shall be allowed exceed 1.5 times the width of road abutting
if such work operates to reduce an open air space of plus the front open space;
any other adjoining building, belonging to the same b) If a building abuts on two or more streets of
owner to an extent less than what is prescribed at the different widths, the building shall be deemed
time of the proposed work or to reduce further such to face upon the street that has the greater
open space if it is already less than that prescribed. width and the height of the building shall be

26 NATIONALBUILDING CODE OF INDIA


Table 3 Comparative Floor Area Ratios for 9.4.2 Height Exceptions
Occupancies Facing One Public Street
9.4.2.1 Roof structures
of at Least 9 m Width
(Clauses 2,26,9.2 and 9.2.1) The following appurtenant structures shall not be
included in the height of the building unless the
Occupancy Type of Construction
aggregate area of such structures, including pent-
Classification ~ houses, exceeds one-third of the area of the roof of
Type 1 Type 2 Type 4
building upon which they are erected:
(1) (2) (3) (4) (5)
a) Roof tanks and their supports (with support
Residential UL 2.0 1.4 1.0
Educational UL 2.0 1.4 1.0 height not exceeding 1 m);
Institutional UL 1.5 1.0 0.8 b) Ventilating, air-conditioning, lift rooms and
Assembly UL 1.0 0.7 0.5
similar service equipmenq
Business UL 2.9 2.3 1.6
Mercantile 8.0 1.8 1.4 1.0 c) Stair cover (MUMTY) not exceeding 3 m in
Industrial 7.5 1.9 1.6 1.3 height; and
Storage 6.0 1.5 1.3 1.0
(see Note 4)
d) Chimneys, parapet walls and architectural
Hazardous 2.8 1.1 0.9 NP features not exceeding 1.2 m in height.
(see Note 4)
9.4.2.2 The building height for differerit occupancy
UL — Unlimited types shall not exceed the maximum height prescribed
NP — Not Permitted in Part 4 ‘Fire and Life Safety’.
NOTES
9.5 Restrictions in the Vicinity of Aerodromes
1 This table has been prepared, taking into account the
combustible content in the different occupancies as well as 9.5.1 For buildings in the vicinity of aerodromes, the
the fire resistance offered by the type of construction (see Part 4
maximum height of such buildings shall be decided in
‘Fire and Life Safety’).
consultation with the Civil Aviation Authorities. Thk
2 This table shall be modified by the Anthority, taking into
account the other aspects as given below (see 9.1):
shall be regulated by the rules for giving no objection
a) Density in terms of dwelling units/hectare;
certificate for construction of buildings in the vicinity
b) Traffic considerations; of aerodromes of Directorate General ,of Civil Aviation,
c) Parking spaces; which are given in Annex A. However, the latest rules
d) Local fue fighting facilities; and of Directorate General of Civil Aviation shall be
e) Water supply, drainage and sanitation requirements. followed in all cases of buildings coming up in the
3 The FAR speeified maybe increased by 20 percent for the vicinity of an aerodrome.
following:
9.5.1.1 For the purpose of 9.5.1 new buildings,
a) A basement or cellar and space under a building
structures which rise to 30 m or more in height and are
constructed on stilts and used as a parking space, and air-
conditioning plant room used as accessory to the principal to be located within 20 km of the aerodrome reference
use; point, shall be constructed only if no objection
b) Electric cabin or sub-station, watchman’s booth of certificate has been obtained from the Directorate
maximum size of 1.6 mz with minimum width or diameter General of Civil Aviation.
of 1.2 m, pumphouse, garbage shaft, space required for
location of fiie hydrants, electric fittings and water td, 9.5.1.2 In the case of buildings to be erected in the
c) Projections and accessory buildings as specifically vicinity of defence aerodromes, the maximum height
exempted (see 8.4.1); and of such buildings shall be decided by the Defence
d) Staircase room and lift rooms above the topmost storey, Authority. “
architectural features; and chmneys and elevated tanks of
dimensions as permissible under the Code; the area of the 9.5.2 This will apply specially to new constructions,
Iift shaft shall be taken ordy on one floor. overhead high voltage/medium voltage lines,
4 In so far as single storey storage and hazardous occupancies telephones/telegraph lines, factories, chimneys, wire/
are concerned, they would be further governed by volume to TV antennas.
plot area ratio (VPR), to be decided by the Authority.
9.5.2.1 No new chimneys or smoke producing
regulated by the width of that street and may factories shall be constructed within a radius of 8 km
be continued to this height to a depth of from the aerodrome reference point (ARP).
24 m along the narrower street subject to 9.5.2.2 Overhead high voltage/medium voltage lines
COrlfOfity Of &, and or telephone/telegraph lines shall not be permitted in
c) For buildings in vicinity of aerodromes, the approachkake-off climb areas within 3000 m of
provisions of 9.5 shall apply. the inner edge of these areas.

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 27


9.5.2.3 A3m margin shall be allowed in new to cross the building line and all other safety features
constructions for wireless/TV antennas, cooling towers for structural, fire, health and public safety being
and MUMTIES. ensured.

9.5.3 Butcheries, tanneries and solid waste disposal 10 OFF-STREET PARKING SPACES
sites shall not be permitted within 10 km from the
aerodrome reference point. 10.1 The off-street parking (on-site parking) spaces
in a plot to be provided shall be in accordance with
9.6 Group Housing Annex B. The spaces given in Annex B shall be
considered by the Authority in conjunction with the
9.6.1 Group housing development may be in low rise
Development Rules, in force, if any.
house clusters or multi-storeyed apartments for high
density development. 10.2 The spaces to be left out for off-street parking as
given in 10.3 to 10.6 shall be in addition to the open
9.6.2 No limit to floors and height shall be applicable,
spaces left out for lighting and ventilation purposes as
but the coverage and floor area ratio for various
given in 15.
densities may be as given in Table 4 unless otherwise
provided in the Master Plan and local development 10.2.1 Further 50 percent of the open spaces required
control rules. around buildings under 8 maybe allowed to be utilized
for parking or loading or unloading spaces, provided a
Table 4 Floor Area Ratio and Coverage for
minimum ~istance of 3.6 m around the building is kept
Group Housing
free from any parking, loading or unloading spaces
(Clause 9.6.2) subject to the provisions of Part 4 ‘Fire and Life Safety’. i-
S1 Net Residential Maximum Floor Area 10.3 Each off-street parking space provided for
No. Density in Dwelling Coverage in Ratio
UNta/ Hectare Percent vehicles shall be as follows:
(1) (2) (3) (4) a) For car, the minimum parking space to be
O 25 25 0.50 3 m x 6 m when individual parking space is
ii) 50 30 0.75 required and 2.75 m x 5 m when common
iii) 75 33 0.90
iv) parking space is required.
too 35 1.00
v) 125 35 1.25 b) Space for scooter/two wheeler and bicycle
vi) 150 35 1.50 to be not less than 1.25 mz and 1.00 mz
vii) 175 35 1.75
respectively.
NOTE — The coverage shatl be calculated on the basis of the c) Area for each equivalent car space inclusive
whole area reserved for group housing.
of circulation area is 23 mz for open parking,
28 mz for ground floor covered parking and
9.6.3 The minimum size of the site for group housing
32 mz for basement.
multi-storeyed apartment shall be 3000 m2.
10.4 For buildings of different occupancies, off-street
9.6.3.1 The number of dwelling units are calculated
parking space for vehicles shall be provided as
on the basis of the density pattern given in the
stipulated below:
Development Plan taking into consideration a
population of 4.5 persons per dwelling unit. a) Motor Vehicles — Space shall be provided
as specified in Annex B for parking motor
9.6.3.2 The basement may vary between 33.33
vehicles (cars).
to 50 percent of the plot area and is to be used for
b) Other Types of Vehicles — For non-residential
parking, servicing and for essential household storage
building, in additjm to the parking areas
without counting in FAR.
provided in (a) above, 25 to 50 percent
9.6.3.3 One car parking space for every two flats up additional parking space shall be provided for
to 90 m2 floor area and one for every flat for 100 m2 or parking other types of vehicles and the additional
more shall be provided. spaces required for other vehicles shall be as
9.6.4 With a view to providing adequate parking for decided by the Authority, keeping in view the
nature of tral%c generated in the city.
occupancies and the vehicular load, appropriate off-
street parking provisions have to be made in the 10.5 Off-street parking space shall be provided with
building/on-site. This could also be permitted in adequate vehicular access to a street; and the area of
basement areas and the footprint for the basement drives, aisles and such other provisions required for
parking can exceed the ground coverage of the adequate manoeuvenng of vehicle shall be exclusive
building subject to no basement building construction of the parking space stipulated in these provisions.

28 NATIONALBUILDING CODE OF INDIA


10.6 If the total parking space required by these 11.4 Cutting and pruning of trees in public as well as
provisions is provided by a group of property owners private areas shall be suitably regulated. Trees shall
for their mutual benefits, such use of this space may be cut only after obtaining the permission of the
be construed as meeting the off-street parking Authority designated for this purpose.
requirements under these provisions, subject to the
11.5 The landscape planning and design shall be done
approval of the Authority.
in accordance with Part 10 ‘Landscaping, Signs and
10.7 In buildings of mercantile (commercial), Outdoor Display Structures, Section 1 Landscape
industrial and storage type, in addition to the parking Planning and Design’.
spaces provided, a space at the rate of 3.5 m x 7.5 m,
shall be provided for loading and unloading activities, 11.6 Water Conservation and Augmentation
for each 1000 mz of floor area or fraction thereof. In view of critical shortage of water, conservation of
10.8 Parking spaces shall be paved and clearly marked water by rain water harvesting and by use of recycled
for different types of vehicles. water to the maximum extent possible will be
required. In this regard the following provisions may
10.9 Apart from parking at ground level, provision of be adopted.
underground or multi storeyed parking may be
permitted. The parking of vehicles at different level 11.6.1 The local authority preparing a town-planning
may also be mechanized. In the case of parking spaces scheme or a development plan should see that the local
provided in basement(s), at least two ramps of adequate water bodies are preserved, and if dry, are activated
width and slope shall be provided, located preferably by directing water-courses appropriately. If required,
at opposite ends. In case of undergroundlmultistoreyed the same should be enlarged, deepened, etc.
parking, special measures with regard to fire safety 11.6.2 The water body should be protected by
shall be taken (see Part 4 ‘Fire and Life Safety’). ensuring that no permanentitemporary construction
development takes place around it up to a distance of
11 GREENBELTS, LANDSCAPING AND WATER
50 m from the edge of the water body and the same
CONSERVATION
shall be suitably landscaped. Further, the public shall
11.1 General have easy access to the water body.

Greenbelts and landscaping including plantation of 11.6.3 The rain water run-off shall be suitably directed
shrubs and trees help to certain extent in enhancing to Recharging Wells in plots belonging to the locrd
the environmental quality. authority and of appropriate design.

11.1.1 Planting of trees in streets and in open spaces 11.6.4 The local authority should encourage for
should be done carefully to take advantage of both collection of rain water from roofs and terraces and direct
shades and sunshine without obstructing the flow of the same either to a storage tank or to a recharging well.
wind circulation and sight. Their advantage for abating
11.6.5 Buildings having central air-conditioning plants
glare and for providing cool andlor warm pockets in
requiring water for cooling purposes may not be
developed areas should also be taken.
allowed to use fresh water for the purpose.
11.2 Norms for Planting of Shrubs and Trees 11.6.6 Commercial or residential muhi-storey complexes
11.2.1 Suitable provisions may be made for greeneries may use recycled water for flushing of toilets. Separate
including plantation of shrubs and trees as a part of storage tanks and separate &ribution pipes shall be
environmental protection in general. This aspect shall provided for the purpose.
be taken care of from the initial stage of town and
12 REQUIREMENTS OF PARTS OR BUILDINGS
country planning, zoning and planning of development
of particular area and group housing. Finally, this 12.1 Plinth
aspect shall also be taken into account in planning
12.1.1 Main Buildings
individual building of different occupancies.
The plinth or any part of a building or outhouse shall
11.2.2 The types of plants, the distance between trees/
be so located with respect to the surrounding ground
plants from the building and the distance between plants
level that adequate drainage of the site is assured. The .
shall be carefully worked out keeping in view the
height of the plinth shall be not less than 450 mm from
structural safety and aesthetic requirements of buildings.
the surrounding ground level.
11.3 Trees shall be numbered area-wise, plot-wise and
12.1.2 Interior Courtyards and Covered Parking
road-wise by the concerned authority and they shall
be checked periodically. Every interior courtyard shall be raised at least 150 mm

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 29


above the determining ground level and shall be shall lead directly or through a sink to a
satisfactorily drained. grated and trapped connection to the waste
pipe;
12.2 Habitable Rooms
b) an impermeable floor;
12.2.1 Height ~
c) a flue, if found necessary; and Y
The height of all rooms for human habitation shall not d) a window or ventilator or opening of size not
be less than 2.75 m measured from the surface of the less than as specified in 15.1.1 subject to
floor to the lowest point of the ceiling (bottom of slab).
increase in area of opening in accordance with
In the case of pitched roof, the average height of rooms
Note 3 of 15.1.2.
shall not be less than 2.75 m. The minimum clear head
room under a beam, folded plates or eaves shall be 12;4 Bathrooms and Water-Closets
2.4 m. In the case of air-conditioned rooms, a height
12.4.1 Height
of not less than 2.4 m measured from the surface of
the floor to the lowest point of air-conditioning duct The height of a bathroom or water-closet measured
or the false ceiling shall be provided. from the surface of the floor to the lowest point in
the ceiling (bottom of slab) shall not be less than
12.2.1.1 The requirements of 12.2.1 apply to
2.1 m.
residential, business and mercantile buildings. For
educational and industrial buildings, the following 12.4.2 Size
minimum requirements apply:
The area of a bathroom shall not be less than 1.8 mz ,&-
a) Educational Ceiling height 3.6 m for all with a minimum width of 1.2 m. The floor area of
Buildings regions; in cold regions, 3 m water-closet shall be 1.1 m2 with a minimum width of
b) Industrial Ceiling height 3.6 m, except 0.9 m. If bath and water-closet are combined, its floor
Buildings when air-conditioned, 3 m area shall not be less than 2.8 m2 with a minimum width
(Factory Act 1948 and Rules of 1.2 m.
therein shall govern such
heights, where applicable). 12.4.3 Other Requirements

12.2.2 Size Every bathroom or water-closet shall:

The area of habitable room shall not be less than 9.5 m2, a) be so situated that at least one of its walls shall
where there is only one room with a minimum width open to external aiq
of 2.4 m. Where there are two rooms, one of these b) not be directly over or under any room other
shall not be less than 9.5 m2 and the other not less than than another water-closet, washing place, bath
7.5 m2, with a minimum width of 2.1 m. or terrace, unless it has a water-tight flooq
12.3 Kitchen c) have the platform or seat made of water-tight
non-absorbent material;
12.3.1 Height
d) be enclosed by walls or partitions and the
The height of a kitchen measured from the surface of surface of every such wall or partition shrdl
the floor to the lowest point in the ceiling (bottom slab) be finished with a smooth impervious material
shall not be less than 2.75 m, except for the portion to to a height of oot less than 1 m above the floor
accommodate floor trap of the upper floor. of such a roqrn;
12.3.2 Size e) be provided. with an impervious floor
covering, slop,img towards the drain with a
The area of a kitchen where separate dining area is
suitable grade and not towards VERANDAH
provided, shall be not less than 5.0 m2 with a minimum
or any other room, and
width of 1.8 m. Where there is a separate store, the
area of the kitchen maybe reduced to 4.5 m2. A kitchen, f) have a window or ventilator, opening to a
which is intended for use as a dining area also, shall shaft or open space, of area not less than
have a floor area of not less than 7.5 m2 with a 0.3 mz with side not less than 0.3 m.
minimum width of 2.1 m. 12.4.4 No room containing water-closets shall be used
12.3.3 Other Requirements for any purpose except as a lavatoxy and no such room
shall open directly into any kitchen or cooking space
Every room to be used as kitchen shall have:
by a door, window or other opening. Every room
a) unless separately provided in a pantry, means containing water-closet shall have a door completely
for the washing of kitchen utensils which closing the entrance to it.

3(J NATIONAL BUILDING CODE OF INDIA


12.5 Ledge or TANDILoft 12.8.2 Size

12.5.1 Height The size of garages shall be as below:

The minimum head-room of ledge or TND/loft shall a) Private Garage — 3.0 m x 6.0 m, minimum;
be 2.2 m. The maximum height of loft shall be 1.5 m. and
b) Public Garage — Based on the number of
12.5.2 Size
vehicles parked, etc (see 10).
A ledge or TAND/loft in a habitable room shall not
cover more than 25 percent of the area of the floor on 12.9 Basement
which it is constructed and shall not interfere with the 12.9.1 The basement shall not be used for residential
ventilation of the room under any circumstances. purposes.

12.6 Mezzanine Floor 12.9.2 The construction of the basement shall be


allowed by the Authority in accordance with the
12.6.1 Height land use and other provisions specified under the
It shall have a minimum height of 2.2 m. Development Control Rules.

12.6.2 Size 12.9.2.1 The basement to be constructed within the


building envelope and subject to maximum coverage
The minimum size of the mezzanine floor, if it is to be on floor 1 (entrance floor) may be put to only the
used as a living room, shall not be less than 9.5 m2. following uses:
The aggregate area of such mezzanine floor in a
building shall in no case exceed one-third the plinth a) Storage of household or other goods of
area of the building. ordinarily non-combustible material;
b) Strong rooms, bank cellars, etc;
12.6.3 Other Requirements Air-conditioning equipment and other
c)
A mezzanine floor maybe permitted over a room or a machines used for services and utilities of the
compartment provided: building; and
d) Parking spaces.
a) it conform to the standard of living rooms as
regards lighting and ventilation in case the 12.9.3 The basement shall have the following
size of mezzanine floor is 9.5 mz or more requirements:
(see 14.1.2);
a) Every basement shall be in every part at least
b) “it is so constructed as not to interfere under 2.4 m in height from the floor to the underside
any circumstances with the ventilation of the of the roof slab or ceiling;
space over and under it;
b) Adequate ventilation shall be provided for the
c) such mezzanine floor is not sub-divided into basement. The ventilation requirements shall
smaller compartments; be the same as required by the particular
d) such mezzanine floor or any part of it shall occupancy according to byelaws. Any
not be used as a kitchen; and deficiency may be met by providing adequate
e) in no case shall a mezzanine floor be closed mechanical ventilation in the form of blowers,
so as to make it liable to be converted into exhaust fans, air-conditioning systems, etc;
unventilated compartments. c) The minimum height of the ceiling of any
basement shall be 0.9 m and the maximum,
12.7 Store Room
1.2 m above the avprage surrounding ground
12.7.1 Height level;
d) Adequate arrangements shall be made such
The height of a store room shall be not less than 2.2 m.
that surface drainage does not enter the
12.7.2 Size basement;
e) The walls and floors of the basement shall be
The size of a store room, where provided in a residential
watertight and be so designed that the effects
building, shall be not less than 3 m2.
of the surrounding soil and moisture, if any,
12.8 Garage are taken into account in design and adequate
damp proofing treatment is given; and
12.8.1 Height
f) The access to the basement shall be separate
The height of a garage shall be not less than 2.4 m. from the main and alternative staircase

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 31


-y--

providing access and exit from higher floors. applicable to boundary walls of jails. In
Where the staircase is continuous in the case industrial buildings, electric sub-stations,
of buildings served by more than one transformer stations, institutional buildings
staircase, the same shall be of enclosed type like sanitoria, hospitals, industrial buildings
serving as a fire separation from the basement like workshops, factories and educational
floor and higher floors. Open ramps shall be buildings like schools, colleges, including
permitted if they are constructed within the hostels, and other uses of public utility
building line subject to the provision of (d). undertakings and strategically sensitive
buildings, a height up to 2.4 m may be
The exist requirements in basements shall comply with
permitted by the Authority.
the provisions of Part 4 ‘Fire and Life Safety’.
12.14 Wells
12.10 Chimneys
Wells, intended to supply water for human consumption
The chimneys shall be built at least 0.9 m above flat
or domestic purposes, where provided, shall comply with
roofs, provided the top of the chimneys is not below
the requirements of 12.14.1 and 12.14.2.
the top of the adjacent parapet wall. In the case of
sloping roofs, the chimney top shall not be less than 12.14.1 Location
0.6 m above the ridge of the mof in which the chimney
penetrates. The well shall be located:

12.11 Parapet a) not less than 15 m from any ash pit, refuse
pit, earth closet or privy and shall be located
Parapet walls and handrails provided on the edges of
on a site upwards from the earth closet or
roof terraces, balcony, VARANDAH, etc shall not be
privy;
less than 1.0 m and not more than 1.2 m in height from
b) not less than 18 m from any cess pit soakway
the finished floor level.
or borehole latrine and shall be located on a.
12.12 Cabin site upwards from the earth closet or privy; ‘
The size of cabins shall not be less than 3.0 mz with a c) that contamination by the movement of sub-
minimum width of 1.0 m. The clear passages within soil or other water is unlikely; and
the divided space of any floor shall not be less than d) not under a tree or otherwise it should have a
0.75 m and the distance from the farthest space in a canopy over it, so that leaves and twigs may
cabin to any exit shall not be more than 18.5 m. In not fall into the well and rot.
case the sub-divided cabin does not derive direct .
lighting and ventilation from any open spaces/ 12.14.2 Requirements
mechanical means, the maximum height of the cabin The well shall:
shall be 2.2 m.
a) have a minimum internal diameter of not less
12.13 Boundary Wall than 1 m,
b) be constructed to a height not less than 1 m
12.13.1 The requirements of the boundary wall are
above the surrounding ground level, to form a
given below:
parapet or kerb and to prevent surface water
a) Except with the special permission of the from flowing into a well, and shall be
Authority, the maximum height of the surrounded with a paving constructed of
compound wall shall be 1.5 m above the impervious material which shall extend for a
centre line of the front street. Compound wall distance of not less than 1.8 m in every direction
up to 2.4 m height may be permitted if the tim the parapet’from the kerb forming the well
top 0.9 m is of open type construction of a head and the upper surface of such a paving
design to be approved by the Authority. shall be sloped away from the well
b) In the case of a corner plot, the height of the c) be of sound and permanent construction
boundary wall shall be restricted to 0.75 m (PUCCA) throughout. Temporary or exposed
for a length of 10 m on the front and side of (KUTCHA) wells shall be permitted only in
the ;nter-sections and the balance height of fields or gardens for purposes of irrigation; and
0.75 m if required in accordance with (a) may d) have the interior surface of the lining or walls
be made up of open type construction of the well be rendered impervious for a
(through railings) and of design to be depth of not less than 1.8 m measured
approved by the Authority. from the level of the ground immediately
c) However, the provisions of (a) and (b) are not adjoining the well-head.

32 NATIONAL BUILDING CODE OF JNDIA


-. —

12.15 Septic Tanks sectional dimension of 0.90 m and not less


than 1.00 m in depth below the invert level of
Where a septic tank is used for sewage disposal, the
the inlet pipe. The pit may be lined with stone,
location, design and construction of the septic tank shall
brick or concrete blocks with dry open joints
conform to requirements of 12.15.1 and 12.15.2 [see
which should be backed with at least 75 mm
also Part 9 ‘Plumbing Services, Section 1 Water
of clean coarse aggregate. The lining above
Supply, Drainage and Sanitation (Including Solid
the inlet level should be finished with mortar.
Waste Management)’].
In the case of pits of large dimensions, the
12.15.1 Location of the Septic Tanks and Subsuglace top portion may be narrowed to reduce the
Absorption Systems size of the RCC cover slabs. Where no lining
is used, specially near trees, the entire pit
A sub-soil dispersion system shall not be closer than
should be filled with loose stones. A masonry
18 m from any source of drinking water, such as well,
ring may be constructed at the top of the pit
to mitigate the possibility of bacterial pollution of water
to prevent damage by flooding of the pit by
supply. It shall also be as far removed from the nearest
surface runoff. The inlet pipe may be taken
habitable building as economically feasible but not
down a depth of 0.90 m from the top as an
closer than 6 m, to avoid damage to the structures.
anti-mosquito measure; and
12.15.2 Requirements h) When the disposal of the septic tank effluent
is to a dispersion trench, the dispersion trench
a) Dimensions of septic tanks — Septic tanks
shall be 0.50 m to 1.00 m deep and 0.30 m to
shall have a minimum width of 750 mm, a
1.00 m wide excavated to a slight gradient
minimum depth of 1 m below the water level
and shall be provided with 150 mm to 250 mm
and a minimum liquid capacity of 1 m3. The
of washed gravel or crushed stones. Open
length of tanks shall be 2 to 4 times the width;
jointed pipes placed inside the trench shall
b) Septic tanks may be constructed of brickwork,
be made of unglazed earthenware clay or
stone masonry, concrete or other suitable
concrete and shall have a minimum internal
materials as approved by the Authority;
diameter of 75 mm to 100 mm. Each
c) Under no circumstances shall effluent from a dispersion trench shall not be longer than
septic tank be allowed into an open channel 30 ‘m and trenches shall not be plac~d closer
drain or body of water without adequate than 1.8 m.
treatment;
d) The minimum nominal diameter of the pipe 12.16 OffIce-cum-Letter Box Room
shall be 100 mm. Further, at junctions of pipes In the case of multi-storeyed multi-family dwelling
in manholes, direction of flow from a branch apartments constructed by existing and proposed
connection shall not make an angle exceeding Cooperative Housing Societies or Apartment Owners
45° with the direction of flow in the main pipe; Associations, limited companies and proposed
e) The gradients of land drains, under-drainage societies, an office-cum-letter box room of dimension
as well as the bottom of dispersion trenches 3.6 m x 3 m shall be provided on the ground floor. In
and soakways shall be between 1:300 and case the number of flats is more than 20, the maximum
1:400; size of the office-cum-letter box room shall be 20 mz.
f) Every septic tank shall be provided with
12.16.1 Business Buildings
ventilating pipe of at least 50 mm d&neter.
The top of the pipe shall be provided with a Provision shall be made for letter boxes on the entrance
suitable cage of mosquito-proof wire mesh. floor as per the requirements of the postal department.
The ventilating pipe shall extend to a height
12.17 Meter Rooms
which would cause no smell nuisance to any
building in the area. Generally, the ventilating For all buildings above 15 m in height and in special
pipe may extend to a height of about 2 m, occupancies, like educational, assembly, institutional,
when the septic tank is at least 15 m away industrial, storage, hazardous and mixed occupancies
from the nearest building and to a height of with any of the aforesaid occupancies having area more
2 m above the top of the building when it is than 500 m2 on each floor, provision shall be made for
located closer than 15 m; an independent and ventilated meter (service) room,
g) When the disposal of septic tank effluent is as per requirements of electric (service) supply
to aseepage pit, the seepage pit may be of undertakings on the ground floor with direct access
any suitable shape with the least cross- from outside for the purpose of termination of electric

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 33


supply from the licensee’s service and alternative water pipe to the road gutter or in any other approved
supply cables. The door/doors provided for the service manner.
room shall have fire resistance of not less than two
12.19.3 Rain-water pipes shall be affixed to the
hours.
outside of the external walls of the building or in
12.18 Staircase/Exit Requirements recesses or chases cut or formed in such external walls
or in such other manner as may be approved by the
12.18.1 The minimum clear width, minimum tread Authority.
width and maximum riser of staircases for buildings
12.19.4 It is desirable to conserve rain water using
shall be as given in 12.18.1.1 to 12.18.1.3 (see also
Part 4 ‘Fire and Life Safety’). suitable rain water harvesting techniques including by
roof water collection. In this context, reference may
12.18.1.1 Mininuon width — The minimum width of be made to Part 9 ‘Plumbing Services, Section 1 Water
staircase shall be as follows: Supply, Drainage and Sanitation (Including Solid
1.0 m Waste Management)’.
a) Residential buildhgs (dwellings)
NOTE — For row housing with 2 storeys, 12.20 Special Requirements of Low Income
the minimumwidth shall be 0.75 m. Housing
b) Residential hotel buildings 1.5 m Special requirements of low income housing shall be
c) Assembly buildings like 2.0 m as given in Annex C. For detailed information in this
auditoria, theatres and cinemas regard, reference may be made to the accepted
d) Educational building 1.5 m standards [3(1)].
,.-
e) Institutional buildings 2.0 m
12.21 Special Re@rementsforPhy sicaUy Challenged
f) All other buildings 1.5 m
Special requirements for planning of buildings and
12.18.1.2 Minimum tread facilities keeping in view the needs of the physically
challenged, applicable particularly to public buildings
The minimum width of tread without nosing shall be
meant for their use, are given in Annex D.
250 mm for residential buildings. The minimum width
of tread for other buildlngs shall be 300 mm. 12.22 Special Requirements for Cluster Planning
for Housing
12.18.1.3 Maximum riser
Special requirements for cluster planning for housing
The maximum height of riser shall be 190 mm for shall be as given in Annex E.
residential buildings and 150 mm for other buildings
and these shall be limited to 12 per flight. 12.23 Special Requirements for Low Income
Habitat Planning in Rural Areas
12.18.2 The minimum head-room in a passage under
Special requirements for low income habitat planning
the landing of a staircase shall be 2.2 m. The minimum
in rural areas shall be as given in Annex F.
clear head-room in any staircase shall be 2.2 m.
12.24 Special Requirements for Development
12.18.3 Exit Requirements
Planning in HElly Areas
All aspects of exit requirements for corridors, doors,
Special requirements for development planning in hilly
stair cases, ramps, etc in respect of widths, travel
areas is given in Annex G.
distmce shall be as per Part 4 ‘Fire and Life Safety’.
13 FIRE AND LIFE SAFETY
12.19 Roofs
For requirements regar@ng fire and life safety for
12.19.1 The roof of a building shall be so designed different occupancies, reference shall be made to Part 4
and constructed as to effectively drain water by means ‘Fire and Life Safety’.
of sufficient rain-water pipes of adequate size,
wherever required, so arranged, jointed and fixed as 14 DESIGN AND CONSTRUCTION
to ensure that the rain-water is carried away from the For requirements regarding structural design, reference
building without causing dampness in any part of the
shall be made to Part 6 ‘Structural Design’ and for
walls, roof or foundations of the building or an adjacent
construction (including safety) reference shall be made
building.
to Part 7 ‘Constructional Practices and Safety’.
12.19.2 The Authority may require rain-water pipes
15 LIGHTING AND VENTILATION
to be connected to a drain or sewer to a covered channel
formed beneath the public footpath to connect the rain- 15.1 For requirements regarding lighting and

34 NATIONAL BUILDING CODE OF INDIA


ventilation for different uses and occupancies, 17 AIR CONDITIONING, HEATING AND
reference shall be made to Part 8 ‘Building Services, MECHANICAL VENTILATION
Section 1 Lighting and Ventilation’.
For requirements regarding design, construction and
15.1.1 Lighting and Ventilation of Rooms installation of air conditioning, heating and mechanical
ventilation systems, reference shall be made to Part 8
Rooms shall have, for the admission of light and air,
‘Building Services, Section 3 Air Conditioning,
one or more openings, such as windows and ventilators,
Heating and Mechanical Ventilation’.
opening directly to the external air or into an open
VERANDAH. 18 ACOUSTICS, SOUND INSULATION AND
15.1.2 Notwithstanding the area of openings obtained NOISE CONTROL
through 15.1, the minimum aggregate area (see Notes For requirements regarding the desired noise levels and
1 to 3) of such openings, excluding doors inclusive of sound insulation in different occtipancies, reference
frames, shall be not less than: shall be made to Part 8 ‘Building Services, Section 4
Acoustics, Sound Insulation and Noise Control’.
a) one-tenth of the floor area for dry hot climate;
b) one-sixth of the floor area for wet hot 19 HEAT INSULATION
climate;
For calculation of solar radiation on buildings and
c) one-eighth of the floor area for intermediate
recommended limits of thermal transmittance of roofs
climate; and
and walls for different parts of the country and heat
d) one-twelfth of the floor ~ea for cold climate. transmission losses due to different constructions,
NOTES reference may be made to good practice [3(2)].
1 If a window is partly fixed, the openable area shall
be counted. 20 INSTALLATION OF LIFTS AND
2 No portionof a room shallbe assumedto be lighted, ESCALATORS
if it is morethan 7.5 m awayfrom the openingassumed
Provision for lifts shall be made for buildings 15 m or
for lighting that portion.
more in height. For requirements regarding planning,
3 The area of openings as given in (a) to (d) above
shallbe increasedby 25 percentin the case of a khchen designing and installation, etc of lifts and escalators,
[see 12.3.3(d)]. reference shall be made to Part 8 ‘Building Services,
Section 5 Installation of Lifts and Escalators’.
16 ELECTRICAL AND ALLIED INSTALLATIONS
(INCLUDING LIGHTNING PROTECTION OF 21 PLUMBING SERVICES AND SOLID WASTE
BUILDINGS) MANAGEMENT

For requirements regarding electrical installations in For requirements regarding water supply, drainage and
buildings including lightning protection of buildings, sanitation (including solid waste management) and gas
reference shall be made to Part 8 ‘Building Services, supply, reference shall be made to Part 9 ‘Plumbing
Section 2 Electrical and Allied Installations’. Services’.

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 35


ANNEX A
(Clause 9.5.1)
CIVIL AVIATION REQUIREMENTS FOR CONSTRUCTION IN THE
VICINITY OF AN AERODROME

A-O GENERAL approach funnel means the area in the shape of an


isosceles trapezium having the longer parallel side
A-O.1 For the purpose of this Annex, the following
1800 m long (900 m on either side of the extended 4
definitions shall apply.
centre line of the runway) and smaller parallel side
A-O.I.I Aerodrome Reference Point (ARP) — This is 180 m long (90 m on either side of the extended centre
a designated point, which is established in the line of the runway), where the smaller and longer
horizontal plane at or near the geometric centre of the parallel sides are placed at a distance of 60 m and
landing area. 6540 m, respectively, from the end of the runway and
at right angles to the extended centre line. Thereafter,
A-O.1.2 Approach Funnel — See Fig. 8.
the trapezium is followed by a contiguous rectangular
A-O.1.3 Elevation or Reduced Level — The vertical area of that width for the remainder of the length up to
distance of a point or a level, on or affixed to the surface a distance of 15060 m from the end of the runway.
of the earth, measured from the mean sea level.
A-1.2.3 An instrument runway is a runway served by
A-O.I.4 Transitional Area — An area which is below visual and non-visual aid or aids providing at least
a specified surface sloping upwards and outwards from directional guidance adequate for a straight in approach
the edge of the approach funnel and from a line and intended for the operation of aircraft using
originating at the end of the inner edge of each instrument approach procedures.
approach area, drawn parallel to the runway centre line
A-1.3 For the Aerodrome at Thiruvananthapurmn
in the direction of landlng (see Fig. 8).
These requirements shall be applicable for the land
A-O.1.5 Runway Strip — See Fig. 8.
enclosed in approach funnels of all runways with a
A-1 PROHIBITED AREA maximum distance of 304.80 m, measured from each
runway and along extended centre line of the runway,
A-1.l No building or structure shall be constructed and the land enclosed in a belt of 30.48 m width outside
or erected, or no tree shall be planted, on any land the operational boundary of the aerodrome. For the
within the limits specified in A-1.2 and A-1.3 in respect purpose of this clause, the requirements of approach
of the aerodromes listed in A-3 and in respect of the funnel and operational boundary shall be as given
aerodrome at Thiruvananthapuram. in A-1.3.1 and A-1.3.2.
A-1.2 For the Aerodromes (see A-3) A-1.3.1 Approach funnel means the area in the shape
These requirements shall be applicable for the land of an isosceles txapezium having the longer parallel side
enclosed in approach funnels of the runway with a of length 4724.4 m (2 362.2 m on either side of the
maximum distance of 360 m measured from each extended centre line of the runway) and smaller parallel
runway and along the extended centre line of the side of 152.4 m (76.2 m on either side of the extended
runway. For the purpose of this clause, the requirements centre line of the runway) where the smaller and longer
of approach funnel and an instrument runway shall be parallel sides are placed at a distance of 60.9 m and
as given in A-1.2.1 to A-1.2.3. 15301 m, respectively, from the end of the runway and
at right angles to the exte@+xl centre line.
A-1.2.1 Approach funnel in the case of an instrument
runway means the area in the shape of an isosceles A-1.3.2 Operational boundary means an area enclosed
trapezium having the longer parallel side 4800 m long between parallel lines at a distance of 152.4 m on either
(2 400 m on either side of the extended centre line of side of the centre line of the runways or 30.4 m from
the runway) and smaller parallel side 300 m long the boundary fencing of the aerodrome, whichever is
(150 m on either side of the extended centre line of greater.
the runway) where the smaller and longer parallel sides
A-2 HEIGHT RESTRICTION
are placed at a distance of 60 m and 15060 m,
respectively, from the end of the runway and at right A-2.1 For the Aerodromes (see A-3)
angles to the extended centre line.
No building or structure higher than the height
A-1.2.2 In the case of a non-instrument runway, the specified in Tables 5 and 6 shall be constructed or

36 NATIONALBUILDINGCODE OF INDIA
I
I
I
A 1“
PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS
37
erected, or no tree which is likely to grow or ordinarily Table 6 Height Restriction with Respect to
grows higher than the height specified in the Tables 5 Transitional Area
and 6, shall be planted, on any land within a radius of (Clauses A-2.1 and A-2.1.2)
20 km from ARP of the aerodromes listed in A-3,
excluding the land covered by A-1.2. S1 D~tance from the Inner Maximum Permissible
No. Boundary of the Transitiorrat Height Above the
Area Specified Above Elevation of the ARP
Table 5 Height Restriction with Respect to
(1) (2) (3)
Approach Funnels
i) Up to a distance of 21 m .
(Clauses A-2.1 am! A-2.1.1)
ii) More than 21 m but not 3
exceedhg 42 m
sl Area Maximum Permissible
No. Height Ahove the iii) Mote than 42 m but not 6
Elevation of the Nearest exceeding 63 m
Runway End iv) More than 63 m but not 9
(1) (2) (3) exceeding 84 m
v) More than 84 m but not 12
i) More than 360 m but not 6 exceeding 105 m
exceeding 510 m
vi) More than 105 m but not 15
ii) More than 510 m but not 9 exceeding 126 m
exceeding 660 m
vii) More than 126 m but not 18
iii) More than 660 m but not 12 exceeding 147 m
exceeding 810 m
viii) More than 147 m bnt not 21
iv) More than 810 m but not 15 exceeding 168 m
exceeding 960 m
ix) More than 168 m but not 24
v) More than 960 m but not 18 exceeding 189 m
exceeding 1 110 m
x) Mom thatt 189 m but not 27
vi) More thao 1 110 m but not 21 exeeeding 210 m
exceeding 1260 m
xi) More than 210 m 30
vii) More than 1 260 m but not 24
exceeding 1410 m
viii) More than 1410 m but not 27 Table 7 Height Restriction
exceeding 1560 m
(Clause A-2.2)
ix) .More than 1560 m 30 ,
SI Area Maximum
a’
A-2.1.1 Table 5 gives the height restriction with No. Permissible Height
Above Ground
respect to approach funnels and shall be applicable for Level
the land enclosed in the approach funnels of all runways (1) (2) (3)
where distances are measured from each end of the
i) The area lying between the coastline 3
runway, along extended certtre line of the runway.
and the Chakai canal other than
A-2.1.2 Table 6 gives height restriction with respect specified in A-13

to transitional area and shall be applicable for the land ii) The area lying in a belt of 457.2 m 6
enclosed in the transitional area of all runways at an width between the Fastem Bank of
the Chakai canat and a tine running
aerodrome listed in A-3 where distances are measured
parallel to this canal for the entire
from the associated runway strip and the edge of the length
associated approach funnels, forming the inner 15.2
iii) A paratlel belt of 762 m width
boundary of the transitional area and along a line at running East of area (ii) above
right angles to the centre line of the runway.
iv) A parattel belt of 609.6 m width 24.3
running East of area (iii) above
A-2.2 For the Aerodrome at Thiruvananthapuram
v) Rest of the area extending up to 20 30.4 t
No building or structure higher than the height km fromARP
specified in Table 7 shall be constructed or erected, or
no tree which is likely to grow or ordinarily grows
A-3 AERODROMES
higher than the height specified in Table 7, shall be
planted, on any level within a radius of 20 km from A-3.1 A list of aerodromes indicating runway
ARP of the aerodrome at Thiruvananthapuram, directions, runway elevations and ARP elevations is
excluding the land covered by A-1.3. given in Table 8.

38 NATIONAL BUILDING CODE OF INDIA


Table 8 Runway Directions, Runway End Table 8 — Continued
Elevations and ARP Elevations for Aerodromes (4) (5)
(1) (2) (3)
(Clause A-3.1)
17. Chennai 10.5 07 12

S1 Aerodrome ARP Runway Runway End 25 15.5


No. Elevation No. Elevation 12 9
m 30 13
(1) (2) (3) (4) (5) 18. Coimbaton? 3% 05 402
23 391
1. Ahmadabad 55 14 54 19. Cooch-Behar 41.5 04 41.5
32 56 22 41.5
05 54 20. Delhi (Pakan) 227 10 219
23 56 28 236.5
2. Agartala 14 05 12 09 220
23 14.5 27 229
18 13.5 21. Delhi (Safdarjung) 212 12 215
36 13.5 30 212
3. Akola 305 10 303 22. Dibrugarh 109.5 05 109
28 303 23 109.5
4. Amritsar 229 07 229 23. Gauhati 48 03 49
25 230 21 48
16 230 24. Gaya 110 10 108
34 229 28 115.5
5. Aurangabad 581 09 582 01 109
27 573.5 19 111
6. Belgaum 758 08 755 25. Hyderabad 531 09 530
26 747 27 522
7. Balurghat 24 09 24 14 531
27 23 32 528
8. Bangalore 888 875 26. Indore 561 07 563.5
27L 881 25 559.5
09L 876 27. Jabalprrr 495 06 480
27R 882.5 24 494.5
9. Vadodara 37 04 36.5 28. Jaipur 385 15 389.5
22 37.5 33 384.4
09 36.5 09 383.7
27 38.7 27 381.3
10. Behala 2.6 18 3.5 29. Jhansi 236 15 236.5
36 3.5 33 236.5
11. Bhavnagar 5.4 07 11 30. Jharsuguda 228 06 228.20
25 6 24 229.14
12. Bhopal 523 06 522.5 31. Kailashadar 27.5 03 28.5
24 521 21 27.5
12 521.5 32. KamsdPur 39 01 45
30 523 19 41
13. Bhubaneshwat 44.5 05 33 33. Kaodla 29 05 29
23 41.5 23 29
14 38 34. Kanpur Iv 10 125
32 37 28 124.5
14. Bhuj 7s.5 05 81.5 35. Keshod 49.5 05 50.5
23 74.5 23 50.5
11 79 18 50
29 77.5 36 52
15. Bilaspur 274 06 270 36. Khajurrdto 217.4 01 “222
24 282 19 210
17 276 37. Kolhapur 607 07 609.6
35 269 25 605.6
16. Chakulia 129 08 135 38. Kolkata 5.3 OIL 4.8
26 132 19R 5
17 130 OIR 5
38 27 19L 4.5

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 39


ANNEX B
(Clause 10.1)
OFF-STREET PARKING SPACES

The off-street parking spaces shall be as given below:

sl Occupancy One Car Parking Space for Eve~


A
No. / \
Population Population Population Population Population
less than 50000 to Between Between Above
50000 200000 200000 to looooooto 5000000
1000000 5000000
(1) (2) (3) (4) (5) (6) (7)

i) Residential — — a) 2 tenements 1 tenement of 1 tenement of


a) Multi-family having built- 100 m2 built- 75 m2 built-up
up area 101 up area area
to 200 m2

— — b) 1 tenement of
200 m2 built- .
up area
b) Lodging 12 guest 8 guest 4 guest 3 guest 2 guest
establishments, rooms rooms rooms rooms rooms
tourist homes and
hotels, with lodging
accommodation
ii) Educational — — 70 m2 area or 50 m2 area or 35 m2 area or
(see Note 1) fraction fraction fraction
thereof of the thereof of the thereof of the
administrative administrative administrative
office area and ofilce area and office area and
public service public service public
--” service
-
areas areas areas
iii) Institutional (Medical) 20 beds 15 beds 10 beds (Private) 5 beds 2 beds
(Private) (Private) (Private) (Private)
30 beds 25 beds 15 beds (Public) 10 beds 5 beds
(Public) (Public) (Public) (Public)
iv) a) Assembly halls, 120 seats 80 seats 25 seats 15 seats 10 seats
cinema theatres

b) Restaurants 60 seats 40 seats 20 seats 10 seats 5 seats


c) Marriage halls, 600 m2 plot 400 m2 plot 200 m2 plot 50 m2 plot 25 m2 plot
community halls area area area “ area area
d) Stadia and 240 seats 160 seats 50 seats 30 seats 20 seats
exhibition centre
v) a) Business offices 300 m2 area 200 m2 area 100 m2 area 50 m2 area 25 m2 area
and firms for or fraction or fraction or fraction or fraction or fraction
private business thereof thereof thereof thereof thereof
b) Public or semip- 500 m2 area 300 m2 area 200 m2 area 100 m2 area 50 m2 area
ublic offices or fraction or fraction or fraction or fraction or fraction
thereof thereof thereof thereof thereof

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 41


“l--
t

(1) (2) (3) (4) (5) (6) (7)

vi) Mercantile 300 mz area 200 mz area 100 mz area 50 mz area 25 m2 area
(see Note 2) or fraction or fraction or fraction or fraction or fraction
thereof thereof thereof thereof thereof
vii) Industrial 400 m2 area 300 mz area 200 m2 area 100 m2 area 50 m2 area
or fraction or fraction or fraction or fraction or fraction
thereof thereof thereof thereof thereof
viii) Storage — — 500 m2 floor 250 m2 area 125 m2 area
area or part or fraction or fraction
thereof , thereof thereof
NOTES
1 In the case of auditoria for educational buildings, parking space shall be provided as per S1 No. (iv)
2 For plots up to 50 mz, as in the case of shops, parking spaces need not be insisted upon.
3 For other institutions, transpoticommunication centre, parking space requirement shafl be assessed based on the proposed building.

ANNEX C

(Clause 12.20) L.-

SPECIAL REQUIREMENTS FOR LOW INCOME HOUSING IN URBAN AREAS

C-1 GENERAL C-2.2 Layout Pattern

C-1.l These guidelines cover the planning and C-2.2.1 In the land to be developed, at least 75 percent
general building requirements of low income housing of the plots maybe of the size less than or up to 60 m2
for houses having a maximum plinth area of 40 m2 per dwelling unit in metropolitan towns and 100 m2 in
including future expansion. The requirement other towns and hill areas. Remaining 25 percent of
regarding layout planning of low income housing the plots may be more than 60 m2, however, no plot
colonies are applicable to public and private agencies/ shall be more than 200 m2. In case of group housing or
government bodies. The requirements on design and flatted development at least 75 percent units should
construction of buildings for low income housing in have a plinth area (excluding external circulation such
approved layouts are applicable to all private and as stairs, lifts, lobbies, etc) up to or not exceeding 40 m2
public agencies. including future expansion.
C-2.2.2 The mix of plot of different sizes should have
C-1.2 In these planning standards, the general master
a wide range to accommodate the need of lower income
plan requirement for community open spaces estimated
group. The project may include more than one site
at 0.3 ha for thousand persons is provided; road areas
provided they are in the same neighbourhood.
are worked out between 10 and 20 percent of the site
area; one nursery school of 0.1 ha is provided for a C-2.2.3 The layout should generally conform to the
population of 1500 and shopping centres at 4 shops following land use:
per thousand population are also covered. -. .—. -.
Lund Under Each Use
C-1.3 It is emphasized that this type of development
should apply to clusters of 400 dwelling units, so General Hill Area’
Saleable
distributed in the development under consideration as
i) Residential 50 percent, 35 percent
to maintain the overall densities of the master plan for
Min
the area.
ii) Work places, schools, 20 percent, 15 percent
institutions, shops, Max
C-2 PLANNING community places, etc
C-2.1 Type of Development Non-Saleable
Roads, pedestrian paths, 30 percent, 50 percent
The type of development for low income housing shall drains, public and semi- Max
be plotted developments as row housing/flatted public open spaces
development as row housing or group housing on NOTES
cluster pattern. 1 Any neighborhood development should have provision for

42 NATIONALBUILDINGCODE OF INDIA
basic civic and community facilities, however, where such C-2.5 Height of Building
facilities are available in proximity the same could be considered
and, in that case, the area under residential use could be increased The height of building shall not exceed 15 m.
correspondingly.
NOTES
2 If land required under statutory provisions of master planl
development plan is proportionately higher but serves larger 1 For buildlngs up to the height of 15 m, there is no need to
city needs, re-adjustment of the recommended land use pattern provide lifts.
can be considered. Such provisions should, however, be 2 Housing for the low-income group shall preferably be up to
carefully reviewed by the planning authorities to keep them to a maximum of two storeys.
the barest minimum levels. 3 Buildings for housing beyond 15 m in height should be
resorted to in exceptional circumstances and it should be
governed by provisions laid down in this Code.
C-2.3 Plot Area

C-2.3.1 Plot Size C-2.6 Cluster Planning

The minimum plot size with ground coverage not For size of open cluster and open space, set backs,
exceeding 75 percent, shall not be less than 40 mz in vehicular access and pedestrian paths in cluster
small and medium town and not less than 30 mz in planning, the provisions given in Annex E shall apply.
metropolitan cities. Plot sizes below 30 m2 but not less
C-3 GENERAL BUILDING REQUIREMENTS
than 15 m2 may be permitted in case of cluster planning,
however, in such cases the ground coverage and FSI C-3.1 General
shall be 100 percent and 2 percent respectively (see
The requirements of parts of buildings shall be as given
also Annex E for Special requirements for cluster
in C-3.2 to C-3.9. —
planning for housing).
NOTES C-3.2 Plinth
1 In exceptional cases in metropolitan cities with population
The minimum height of plinth shall be regulated on
more than 1 million the size of plots may be brought down to
25 mz in cases of low income housing colonies located in the basis of environmental and topographical condition
congested areas as decided by the Authority. In mega-cities it and higher plinth height may be required in areas prone
may be further reduced to 15 m2.1n such cases where plot size to flooding.
is below 25 mz, only cluster planning or group housing may
be adopted. C-3.3 Size of Room
2 Aminimum of25percent of theplot size shall be left open
without adversely affecting light and ventilation for habitable C-3.3.1 Habitable Room
spaces and toilet. It shall not be made mandatory to leave set
back on any side.
Every dwelling unit to be provided should have at least
two habitable rooms. Even if one room house is
C-2.3.2 Minimum Frontage provided initially it should be capable of adding a new
Theminimum frontage of the plot shall be 3.6min second room in future. However, in case single room
width. tenements are required to be provided where future
additions are not possible, the carpet area of
C-2.4 Density multipurpose single room should be at least 12.5 m2.
The density norms for plotted development and mixed Such one room dwelling units with 12.5 m2 carpet area
development shall be as follows: of habitable space is permitted only in case of on site
rehabilitation of slum dwellers. In a house of two
Type of Development Range of Densities rooms, first room shall. not be less than 9.0 m2 with
(Gross) minimum width of 2.5 m and second room shall not
a) Plotted development 65-120 plots per hectare be less than 6.5 m2 with@ minimum width of 2.1 m
b) Mixed development provided the total area of both the rooms is not less
i) Small towns 75-100 dwelling units than 15.5 m2. In incremental housing the bigger room
per hectare shall always be the first room.

ii) Cities 100-125 dwelling units C-3.3.1.1 To facilitate incremental housing in case of
per hectare flatted development or otherwise, habitable space at
iii) Metropolitan Cities 125-150 dwelling units mezzanine level may be permitted. The minimum size
per hectare of such a mezzanine floor should not be lesser than
6.5 m2 and such a floor should occupy not more than
C-2.4.2 In case of developments with per dwelling 50 percent of the room area of which it is a part. Such
unit covered area of 15 m2 maximum densities of 500 a mezzanine floor should have appropriate openings
dwelling units per hectare shall be permissible. to facilitate light and ventilation as per C-3.6. Minimum

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 43


clear height below and above the mezzanine floor NOTE — The windows and other openings shall abut onto
open spaces either through areas left open within the plot or
should be 2.4 m and 2.1 m respectively.
the front, side and rear spaces provided in the layouts which
As far as possible mezzanine floor should have direct shall be deemed to be sufficient for light and ventilation
purposes. Wherever ventilatiott/tighting is provided by means
ventilation from the external face of the building.
of JAIJ or grill of any material, total area of openings shall
Where this is not possible ventilation through main calculated excluding solid portion of the .fALf or grill.
room may be allowed provided total area of openings
in the main room is provided taking into consideration C-3.7 Stairs
area of mezzanine floor. The following criteria shall be adopted for internal
Such mezzanine floor may be accessible through the individual staircase:
main room by a ladder, whose minimum angle with
vertical plane should be 22%0. Height of the riser a) Minimum Width
should be less than 250 mm. 1) 2 storeyed — straight 0.60 m
2) 2 storeyed — winding 0.75 m
C-3.3.2 Water Closet/Bathroom
3) 3 or more storeyed — 0.75 m
1) The size of independent water-closet shall be straight
0.90 m’ with minimum width of 0.9 m; 4) 3 or more storeyed — 0.90 m
2) The size of independent bathroom shall be winding
1.20 m’ with a minimum width of 1.0 m; and b) Riser 200 mm, Max
3) The size of combined bathroom and water-
closet shall be 1.80 m’ with minimum width
of 1.0 m.
c) Tread
1) 2 storeyed 225 mm, &fin
(see Note) r.
ir$

2) 3 storeyed or more 250 mm, Min


c-3.3.3 Kitchen
d) Head Room — The minimum
The size of a cooking alcove serving as cooking space clear head room shall be 2.1 m.
shall not be less than 2.4 m2 with a minimum width of
NOTE — This could be reduced to 200 mm as the clear tread
1.2 m. The size of individual kitchen provided in a
between perpends, with possibility of open riser as well as
two-roomed house shall not be less than 3.3 mz with a nosing and inclined riser to have an effective tread of 225 mm.
minimum width of 1.5 m.

C-3.3.4 Balcony C-3.8 Circulation Area

The minimum width of individual balcony, where The circulation area on any floor inclu&g staircase,
provided, shall be 0.9 m and shall not be more than shall not exceed 8 m2/dwelling unit.
1.2 m and it shall not project beyond the plot line and C-3.9 Water Seal Latrine
on roads or pathway.
No building plan shall be approved and no building
C-3.4 Basement shall be deemed to have been completed and fit for
human occupation unless provision is made for water
No basement floor shall be allowed.
seal latrine. No dry latrine shall be allowed. Water seal
C-3.5 Minimum Height latrines can also be provide on the basis of community
toilets or shared toilets as per the recommendation
The minimum height of rooms/spaces shall be as given in good practice [3(3)].
follows:
Where leaching pits are used, it should be constructed
a) Habitable room 2.6 m within the premises of the households as it would be
b) Kitchen 2.6 m economical as well as facilitate their cleaning. However,
c) Bath/water-closet 2.1 m where, due to space constraint, construction of pits
d) Corridor 2.1 m within the premises may not be possible, pits may be
constructed in places like lanes, streets and roads.
C-3.5.1 In the case of sloping roofs, the average height
of roof for habitable rooms shall be 2.6 m and the In case the pit is located under the road, street or foot
minimum height at eaves shall be 2.0 m. path, the inverted level of the pipe connecting the
latrine pan with the pit shall be at least 1.1 m below
C-3.6 Lighting and Ventilation ground level or below the bottom of the water main
The openings through windows, ventilators and other existing within a distance of 3 m from the pits
openings for lighting and ventilation shall be in whichever is more. Construction of such pits may be
accordance with 15.1.2. in accordance with good practice [3(4)].

44 NATIONALBUILDINGCODE OF INDIA
The water seal latrine should be properly maintained be provided. In the absence of piped water supply, hand
and kept in sanitary condition by the owner or the pumps may be used for provision of water supply.
occupier. The contents of the septic tanks, soak pits,
C-5.3 Recognizing the need for informal use of space
leach pits, etc should be periodically emptied.
for shopping and informal occupation like road side
The leach pits should be cleaned only after 2 years of repairs, pan shops, etc, it is suggested that about % of
their being put out of service after they were full. the total shopping area in a layout should be reserved
for such informal uses to cater to the needs of low
C-4 ROADS AND PATHWAYS income families.
The area under roads and pathways in such housing C-5.4 The infrastmctural services shall be provided
projects should normally not exceed 20 percent of the before the plots are handed over to individual owners.
total land area of the project.
C-6 SITE AND SERVICES SCHEMES
Access to the dwelling units, particularly where
motorized vehicles are not normally expected should C-6.1 The developed plot sizes shall be as per C-2.3.1.
be by means of paved footpaths with a right of way Services would have to be laid by the Agency
of 6 m and a pathway of 2 m only. The right of way concerned as per the provisions of the Code. In so far
should be adequate to allow for the plying of as roads and pathways are concerned, they could also
emergency vehicles and also for road side drains and be in line with C-4.
plantation.
C-6.2 Site and services schemes shall provide for the
Where pedestrian pathways are not meant for following.
motorable access to the minimum, right of way of such
a) Complete infrastructural needs for a
pedestrian pathway shall be 3 m. Where houses are
permanent housing, on the periphery of
accessible from one side only pathway can be 2 m wide.
individual plot or a group/cluster plots;
The maximum length of such pathways should not be
b) A service sanitary core in the plo~
more than 60 m.
c) A skeletal structure of columns and roof or a
C-5 OTHER REQUIREMENTS developed plinth; and
C-5.1 Requirements of fire safety, structural design, d) Permission to allow temporary construction
building services and plumbing services shall be as on the plot.
specified in the Code. While provisions in C-6.2(a) and C-6.2(d) are
C-5.2 One water tap per dwelling unit may be essential in site and services projects provisions,
provided, where adequate drinking water supply is recommendations in C-6.2(b) and C-6.2(c) are
available. If supply is inadequate, public hydrants shall additional provisions depending upon affordability.

ANNEX D
(Clause 12.21)
SPECIAL REQUIREMENTS FOR PLANNING OF PUBLIC BUILDINGS
MEANT FOR USE OF PHYSICALLY CHALLENGED

D-1 GENERAL the public accessible to, and functional for the physically
challenged through and withiq~eir doors, without loss
D-1.l These requirements apply to all buildings and
of function, space or facility where the general public is
facilities used by the public, These apply to temporary
concerned. It supplements the general requirements of
or emergency conditions as well as permanent
the Code, and reflects _ concern for safety of life
conditions. It does not apply to private residences.
and limb. In cases of practical difllculty, unnecessary
These requirements are concerned with non- hardship, or extreme differences, the Authority may grant
ambulato~ disabilities, semi-ambulatory disabilities, exceptions from the literal requirements of this Amex or
sight disabilities, hearing disabilities, disabilities of permit the use of other methods or materials, but only
into-ordination, aging, allergies, heart and lung when it is clearly evident that equivalent facilities and
diseases, epilepsy, hemophilia, incontinence and protection are thereby secured.
enterostomy.
D-1.2 For the purpose of this Annex, the following
It is intended to make all buildings and facilities used by definitions shall apply.

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUiLDING REQUIREMENTS 45


“.. —

D-1.2.1 Aging D-1.2.3.9 People with incontinence, enterostomy


operations, etc
Those manifestations of the aging processes that
significantly reduce mobility, flexibility, co-ordination, The requirements of people with incontinence,
and perceptiveness but are not accounted for in the enterostomy operations, etc (colostomies, ileostomies
categories mentioned in D-1.2.3.1 to D-1.2.3.9. and urostomies) are mainly related to bathroom
provision. In certain circumstances, for example, in
D-1.2.2 Appropriate Number
public water-closet compartments, it maybe desirable
The number of a specific item that would be necessary, to provide a special sink for emptying urine bags.
in accordance with the purpose and function of building
D-1.2.4 Fixed Turning Radius, Front Structure to Rear
or facility, to accommodate individuals with specific
Structure
disabilities in proportion to the anticipated number or
individuals with disabilities who would use a particular The turning radius of a wheelchair, left front-foot
building or facility. platform to right rear wheel, or right front-foot platform
to left rear wheel, when pivoting on a spot.
D-1.2.3 Disabilities
D-1.2.5 Fixed Turning Radius Wheel
D-1.2.3.1 Non-ambulatory disabilities
The tracking of the caster wheels and large wheels of
Impairments that, regardless of cause or manifestation,
a wheelchair when pivoting on a spot.
for all practical purposes, confine individuals to
wheelchairs. D-1.2.6 Involved (Involvement)

D-1.2.3.2 Semi-ambulatoq disabilities A portion or portions of the human anatomy or


physiology, or both, that have a loss or impairment of .-
Impairments that cause individuals to walk with
normal function as a result of genesis, trauma, disease,
difficulty or insecurity. Individuals using braces or
inflammation or degeneration.
crutches, amputees, arthritis, spastics and those with
pulmonary and cardiac ills may be semi-ambulatory. D-1.2.7 Ramps, Ramps with Gradients

D-1.2.3.3 Sight disabilities Because the term ‘ramp’ has a multitude of meanings
and uses, its use in this text is clearly defined as ramps
Total blindness or impairments affecting sight to the
with gradients (gradual slope joining two level
extent that the individual functioning in public areas surfaces) that deviate from what would otherwise be
is insecure or exposed to danger.
considered the normal level. An exterior ramp, as
D-1.2.3.4 Hearing disabilities distinguished from a ‘walk’, would be considered an
appendage to a building leading to a level above or
Deafness or hearing handicaps that might make an
below the existing ground level.
individual insecure in public areas because he is unable
to communicate or hear warning ,signals. D-1.2.8 Walk Walks

D-1.2.3.5 Disabilities of into-ordination Because the terms ‘walk’ and ‘walks’ have a multitude
of meanings and uses, their use in this standard is
Faulty co-ordination or palsy from brain spinal, or
clearly defined as a predetermined prepared surface,
peripheral nerve injury.
exterior pathway leading to or from a building or
D-1.2.3.6 People with allergies facility, or from one exterior area to another, placed
on the existing ground level and not deviating from
People with allergies may be sensitive to dust, mildew,
the level of the existing ground immediately adjacent.
pollen, animal hair, formalin, turpentine, etc. Some are
sensitive to contact with substances and materials, such D-2 SITE DEVELOPMENT
as, nickel, chromium and rubber.
D-2.1 Almost any building can be made accessible to
D-1.2.3.7 People with heart and lung diseases physically challenged persons by so planning the site
People with heart and lung diseases may only be able that the terraces, retaining walls and winding walks
to walk short distances and may be unable to climb are used effectively.
stairs. The requirements of these people are similar to D-2.1.1 Site development is the most effective means
those with impaired mobility. to resolve the problems created by topography,
D-1.2.3.8 People with epilepsy, hemophilia, etc definitive architectural designs or concepts, water table,
existing streets, and typical problems, singularly or
The requirements of those with epilepsy, hearnophilia, collectively, so that aggress, ingress and egress to
etc, are related primarily to the design of buildings and buildings by physically challenged maybe facilitated
the need to minimize the risk of injury caused by falling while preserving the desired design and effect of the
or encountering obstacles. architecture.

46 NATIONALBUILDING CODE OF INDIA


D-2.2 Walks shall extend at least 300 rnm beyond each side of the
doorway.
D-2.2.1 Public walks should beat least 1200 mm wide
and should have a gradient not greater than I in 20. D-2.2.5 A walk shall have a level platform at least
900 mm deep, if the door does not swing onto the
D-2.2.1.1 It is essential that the gradient of walks and
platform or towards the walk. This platform shall extend
driveways be less than that prescribed for ramps, since
at least 300 mm beyond each side of the doorway.
walks would be devoid of handrails and kerbs and
would beconsiderably longer and more \ulnerable to D-2.3 Parking Space
the elements. Walks of near maximum grade and
considerable length should have level areas at intervals D-2.3.1 Spaces that are accessible and approximate
for purposes of rest and safety. Walks or driveways to the facility should be set aside and identified for use
should have a non-slip surface. by individuals with physical disabilities.

D-2.2.2 Such walks shall be of a continuing common D-2.3.2 A parking space open on one side, allowing
surface not interrupted by steps or abrupt changes in level. room for individuals in wheelchairs or individuals on
braces and crutches to get in and out of an automobile
D-2.2.3 Wherever walks cross other walks, driveways,
onto a level surface, is adequate. It should have a
or parking lots they should blend to a common level.
minimum width of 2700 mm preferably 2 800 mm
D-2.2.3.1 This requirement, does not require the for ambulant disabled and minimum 3 000 mm
elimination of kerbs, which, particularly if they occur preferably 3300 mm for wheel chair users.
at regular intersections, are a distinct safety feature for
all of the challenged, particularly the blind. The D-2.3.3 Parking spaces for individuals with physical
preferred method of meeting the requirement is to have disabilities when placed between two conventional
the walk incline to the level of the street. However, at diagonal or head-on parking spaces should be 3.6 m
principal intersections, it is vitally important that the to 3.8 m wide and the length of the aisle should 7.3 m,
kerbs run parallel to the street, up to the point where 6.1 m and 6.5 m for head-on, 90° and 60° parking
the walk is inclined, at which point the kerb would respectively.
turn in and gradually meet the level of the walk at its D-2.3.4 Care in planning should be exercised, so that
highest point. A less preferred method would be to individuals in wheelchairs and individuals using braces
gradually bring the surface of the driveway or street to and crutches are not compelled to wheel or walk behind
the level of the walk. The disadvantage of this method
parked cars.
is that a blind person would not know when he has left
the protection of a walk and has entered the hazards of D-2.3.5 Consideration should be given to the
a street or driveway (see Fig. 9). distribution of spaces for use by the disabled in
accordance with the frequency and persistency of
D-2.2.4 A walk shall have a level platform at the top
parking needs.
which is at least 1 500 mm long, if a door swings out
onto the platform or towards the walk. This platform D-2.3.6 Walks shall be in conformity with D-2.2.

MAX. GRADIENT 1 IN 10

KERB MAX. 25mm HIGH

FIG. 9 SUITABLEMETHOD OF BLENDINGPAVEMENTAND ROADWAY SURFACES

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDING REQUIREMENTS 47


D-3 BUILDINGS greatly assists the challenged persons with semi-
ambulatory and ambulatory disabilities. Non-slip
D-3.1 Ramps with Gradients
surfaces are provided by many finishes and materials.
Where ramps with gradients are necessary or desired, they The surfaces of the concrete ramps can be made non-
,)
shall conform to the following requirements (see Fig. 10).
/ skid by brooming the surface or by finishing with an
indenting roller.
D-3.1.1 A ramp when provided should not have a
I
slope greater than 1 in 20 or maximum of 1 in 12 for D-3.1.4 A ramp shall have a level platform at the top
short distance up to 9000 mm. which is at least 1 800 mm long, if a door swings out
onto the platform or toward the ramp. This platform 1
D-3.1.2 A ramp shall have handrails on at least one >
shall extend at least 300 mm beyond each side of the
side, and preferably two sides, that are 900 mm high,
doorway (see Fig. 11). 1
measured from the surface of the ramp, that are smooth,
and that extend 300 mm beyond the top and bottom of D-3.1.5 Each ramp shall have at least 1800 mm of
the ramp. Where major traffic is predominantly straight clearance at the bottom.
children, the handrails should be placed 760 mm high.
D-3.1.6 Ramps shall have level platforms at 10 m to ,1
NOTES 12 m intervals for purposes of rest and safety, and shall
k;
,
1 Where handrails are specified to be of heights other than have platforms minimum 1.5 m length wherever they
80 cm, it is recommended that two sets of’handrti?k be installed
turn.
to serve all people. Where major traffic is predominantly
children, particularly physically disabled chikirtm, extra care D-3.1.7 For visually impaired people, ramps may be
should be exercised in the placement of handrails, in
accordance with the nature of the facility and the age group or
colour contrasted with landing.
groups being serviced (see also D-3).
D-3.1.8 To minimize rise to wheelchair users, ramps
2 Care should be taken that the extension of the handrails is
should be equipped with herbs approximately 50 mm
not in itself a hazard. Extension up to 300 mm may be made
on the side of a continuing wall. high at exposed sides.

D-3.L3 A ramp shall have a surface that is non-slip D-3.2 Entrances


surface and if length is 3500 mm, the minimum width
D-3.2.1 At least one primary entrance to each building
shall be 1500 mm.
shall be usable by individuals in wheelchairs (see
D-3.1.3.1 The provision of non-slip surfaces on ramps Fig. 12A) and shall be indicated by a sign (see Fig. 12B).

RECESS ENTRANCE DOOR


WHERE IN EXPOSED POSITION-7

1800 x 1800 mm MIN.


LEVEL PLATFORM

50 mm KERB
1 r EXTENDED HANDRAIL AT
HEAD OF RAMP

50 mm KERB TO EXPOSED
SIDE OF RAMP

ALTERNATIVE STEPPED
APPROACH WHERE RAMP
GRADIENT EXCEEDS 1 IN 12
TREAD MIN. 300 mm
RISERS MAX. 150 mm
L

/
OR MAXIMUM OF 1:12 \
FOR SHORT DISTANCE
EXTENDED HANDRAIL 1
AT FOOT OF RAMP

FIG. 10 EXAMPLE OF RAMPED APPROACH

48 NATIONAL BUILDING CODE OF INDIA


-

RAMP ‘Inl *
UP OR UP OR 1800
DOWN 300 min

I 3 ‘

1800 J

All dimensions in millimetres.

FIG. 11 LEVELAREAS REQUIREDAT END OF RAMPSLEADINGTO DOORWAYS

(LUMINOUS CGLOUR)

t“5ii-380 min

12A PLAN OF 000RS


WHITE~
/
BLACKJ

12B SIGN FOR USE AT


SUITABLE FOR THE THE ENTRANCE
WHEELCHAIR BOUND

FIG. 12 ENTRANCES

D-3.2.2 At least one entrance usable by individuals D-3.3.1.1 Two-leaf doors are not usable by those with
in wheelchairs shall be on a level that would make the disabilities defined in D-1.2.1, D-1.2.2 and D-1.2.5
elevators accessible. unless they operate by a sipgle effort, or unless one of
the two leaves meets the requirements of D-3.3.1.
D-3.3 Doors and Doorways
D-3.3.1.2 Side-hung doors
D-3.3.1 Doorwidth
To facilitate wheelchair manoeuvre, doors should be
To enable wheelchair users to pass through doors, the hung with the hinges in room corners. Doors opening
minimum clear width should be 900 mm and shall be out into corridors or circulation spaces should be
operable by a single effort. In certain cases the clem avoided as far as possible.
width should be 900 mm to 1000 m, for example, if
the wheelchair has to be turned in the doorway, where D-3.3.1.3 It is recommended that all doors have kick
there is a door-closer or at entrance doors to public plates extending from the bottom of the door to at least
buildings and in other situations where there is 400 mm from the floor, or be made of a material and
considerable traffic. finish that would safely withstand the abuse they might

PART 3 DEVELOPMENTCONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 49


VERTICAL

“’Ll r--l

r I*
175 APPROX,
[ ‘,
x 1 1 r TOILET PAPER

.
? HOLDER
760 min. c
SUGGESTED I
POSITION FOR

B
FLUSH HANDLE 1~~$

..1 3jo

\
\ WASH HAND BASIN WITH
TOWEL DISPENSER OVER
RIM AT 810 mm ABOVE
255 APPROX. L FLOOR

HORIZONTAL
PULL RAIL

ALTERNATIVE
7 \ VERTICAL
RAIL

FOR DOOR
L
s
9
RISING BUTQ/’ 1370 mm min. (3R 1520 mm WHERE
HINGES ~ DEPTH IS LESS THAN 1750 mm OR ————
DOOR IN ALTERNATIVE POSITION

All dimensions in millimetres.

FIG. 17 SUGGESTEDPLAN OF WC COMPARTMENTFORTHEWHEELCHAIRBOUND

..
Sa II
II II
II II
11 1{
II
PAPER II
II TOWEL II
II DISPENSER II
RA1l-AT 280 mm
ABOVE WC SEAT
II 7II}1

\
II
II
II TOILET
II rPAPER
4u VERTICAL ‘A ‘r
I Q*KmmTrn 4

II

\
II
tl
II
Ir

&

--!
Wc SEAT AT
BASIN RIM AT
780 mm
ABOVE FLOOR
500mm
ABOVE FLOOR
w II I I

All dimensions in millimetres.

FIG. 18 SECTIONTHROUGHWC COMPARTMENTFOR THEWHEELCHAIRBOUND

52 NATIONAL BUILDING CODE OF INDIA


D-3.7.2 Sanitary facilities shall have at least one water- designs demand, so that they are usable by individuals
closet cubical for the ambulant disabled (see Fig. 19 in wheelchairs.
and 20), that: D-3.7.3.1 The drain pipes and hot-water pipes under
a) is 900 mm wide; a sanitary appliance shall be covered or insulated so
b) is at least 1500 mm, preferably 1600 mm deep; that a wheelchair individual do not find it inconvenient.
c) has a door (where doors are used), that is, D-3.7.4 Some mirrors and shelves shall be provided
800 mm wide and swings out; above the wash basins at a height as low as possible
d) has handrails on each side, 780 mm high and and not higher than 1 m above the floor, measured
parallel to the floor, 40 mm clearance between from the top of the shelf and the bottom of the mirror.
rail and wall, and fastened securely at ends
D-3.7.5 Sanitary facilities for men shrdl have wall-
and centre; and
mounted urinals with the opening of the basin 460 mm
e) has a water-closet with the seat 500 mm from
from the floor, or shall have floor-mounted urinals that
the floor.
are on level with the main floor of the toilet room.
NOTE— The design and mounting of the water-closet
is of considerable importance. A wall-mounted water- D-3.7.6 Toilet rooms shall have an appropriate number
closet with a narrow understrocture that recedes sharply of towel racks, towel dispensers, and other dispensers
is most desirable. If a floor mounted water-closet must
and disposal units mounted not higher than 910 mm
be used, it should not have a front that is wide and
perpendicular to the floor at the front of the seat. The from the floor.
bowl should be shallow at the front of the seat and turn
backwards more than downwards to allow the individual D-3.8 Drinking Fountains
in a wheelchair to get close to the water-closet with the
seat of the wheelchair. An appropriate number of drinking fountains or other
.
water-dispensing means shall be accessible to and
D-3.7.3 Sanitary facilities shall have wash basins with usable by the physically disabled.
narrow aprons, which when mounted at standard height
are usable bv. individuals in wheelchairs: or thev. shall D-3.8.1 Drinking water fountains or water coolers
have wash basins mounted higher, when particular shall have up front spouts and control.

r II
II
I I II
II
TOILET PAPER
II II
II
HOLDER
H II f

[
T280 mm
“ (j ‘-
b -J

330’mm

a -i
II Ih
II II \’ HORIZ~AL RAIL AT
II II 260 mmASOVE WC

I--’8”””71? \
\
SEAT L-
/’
“
VERTICAL RAIL
*900mm+
1295 mm HIGH
\
\ RECOMMENDED
EXTENSION TO
HORIZONTAL RAIL

-
T- HORIZONTAL
PULL RAIL

FIG. 19 SUGGESTED
PLANWC COMPARTMENT
FORTHEAMBULANT

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 53


r

r
RAIL AT 280 mm
ABOVE WC SEAT
!

“J
TOILET PAPER VERTIC/iL R&L c
HOLDER 835mm TO 1295 mm
ABOVE FLOOR

l--
280 mm
I

t .
r...-
II ABOVE FLOOR
I II

FIG. 20 SECTIONTHROUGHWC COMPARTMENT


FORTHEAMBULANTDISABLED

D-3.8.2 Drinking water fountains or water coolers be securely fitted to the wall to withstand heavy pressure.
shall be hand-operated, or hand and foot-operated. Handrails should turn in towards the wall at either end.

D-3.8.2.1 Conventional floormounted water coolers D-3.1O.1 Handrails should be approximately 900 mm
may be convenient to individuals in wheelchairs if a from the floor. The rail should be easy to grip, having
small fountain is mounted on the side of the cooler a circular section with a diameter of approximately
800 mm above the floor. 40 mm and fixed as shown in Fig. 21.

D-3.8.2.2 Fully recessed drinking water fountains are


not recommended.

D-3.8.2.3 Drinking water fountains should not beset into


an alcove unless the alcove is wider than a wheelchair.

D-3.9 Public Telephones


An appropriate number of public telephones should be
made accessible to and usable by the physically disabled.
NOTE — The conventional public telephone booth is not
usable by most physically disabled individuals. There are many
ways in which public telephones may be made accessible and
usable. It is recommended that architects and builders confer
with the telephone companies in the planning of the building
or facility.

D-3.9.1 Such telephones should be kept so that the dial


is placed at minimum 1 200 mm from floor and the
handset may be reached by individuals in wheelchairs.

D-3.1O Handrails
Handrails are used as a locational and mobility aid by
All dmensions in milfimetres.
blind and visually impaired people, and as a support for
people with mobility impairments. The handrail should FIG. 21 FIXINGOF HAND RAIL

54 NATIONALBUILDINGCODE OF INDIA
D-3.1O.2 To aid identification, the colour of the rail wall, to left of the door, preferably at a height of
should contrast with the wall behind. 1500 mm from the floor.

D-3.11 Elevators D-3.13.3 Doors that are not intended for normal use,
and that might prove dangerous if a blind person were
In a multi-storey building, elevators are essential to to exit or enter by them, should be made quickly
the successful functioning of physically disabled identifiable to the touch by knurling the door handle
individuals. They shall conform to the requirements or knob (see Fig. 22).
given in D-3.11.1 and D-3.11.2.

D-3.11.1 Elevators shall be accessible to, and usable KNURLINGS


7
by the physically disabled on the level that they use to
enter the building, and at all levels normally used by
the general public.

D-3.11.2 Elevators shall allow for traffic by wheelchairs


(see also D-3.3).

D-3.12 Controls

It is advantageous for wheelchair users if controls are


placed at low level. For visually impaired people, they
should be at eye-level.
u
D-3.12.1 To enable wheelchair users to reach controls
while not placing them too low for visuall impaired FIG. 22 DOOR HANDLE
people, controls should be in the zone $ 00 mm to
1200 mm from the floor. It is advantageous if controls D-3.14 Warning Signals
in, for example, lifts are placed at an angle of
D-3.14.1 Audible warning signals shall be accompanied
approximate y 45° to the wall so that they are easier to
by simultaneous visual signals for the benefit of those
read and operate. To cater for wheelchair users,
with hearing disabilities.
controls should be placed not less than 400 mm from
room comers. All the power and electric points should D-3.14.2 Visual signals shall be accompanied by
be placed at one metre above the floor level and should simultaneous audible signals for the benefit of the
not project outside walls. blind. To assist blind people, lettering and symbols on
signs should be in relief for tactile reading.
D-3.12.2 Again, to cater for visually impaired people,
controls should be colour-contrasted with D-3.14.3 Signs should be designed and located so that
backgrounds. Information should preferably be in relief they are easy to read. For visually impaired people,
for tactile reading. signs should preferably be at eye-level and it should
be possible to approach them closely. Text and symbols
D-3.12.3 To aid operation for people with impaired
should be colonr-contrasted with the background. The
co-ordination or impaired vi~on, switches, etc, should
letters should not be less than 12 nun high.
have large push plates.
D-3.14.4 Signs should be well illuminated and
D-3.12.4 Controls for powered door openers to hinged
doors should be located so that the doors do not conflict surfaces should not cause mirroring or reflections.
with wheelchairs, sticks, walking aids, etc. Signs should not be behind glass or similar materials.

D-3.12.5 To facilitate operation for people with D-3.14.5 Information baspd on colour codes only
limited strength in arms and hands, handles should be should be avoided; colorblind people may find them
easy to grip and turn. difficult to understand.

D-3.13 Identification D-3.15 Work Bench

Appropriate identification of specific facilities within This should be at least 800 mm wide, 600 mm deep
a building used by the public is particularly essential and 650 mm to 700 mm high. For wheelchair users,
to the blind. the convenient height of work tops is between
750 mm and 850 mm; flexible provision is preferred.
D-3.13.1 Raised letters or numbers shall be used to
Further, for wheelchair access to a work bench, wash
identify rooms or offices.
basin or table, a clear space for knees and footrests is
D-3.13.2 Such identification should be placed on the needed.

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 55


E-2.7 Right to Build in Sky E-2.11 Density

Pedestrian paths and vehicular access roads to clusters Cluster planning methodologies result in higher
separating two adjacent clusters may be bridged to densities with low rise structures. With per dwelling
provide additional dwelling units. While bridging the unit covered area of 15 mz densities of 500 dwelling
pedestrian path way minimum clearance should be one units per hectare (net) shall be permissible. Densities
storey height; length of such bridging should be not more higher than this should not allowed.
than two dwelling units. While bridging the vehicular
E-2.12 Group Toilet
access roads minimum clearance should be 6 m.
Cluster housing for economically weaker section
E-2.8 Vehicular Access families can have group toilets at the rate of one water-
A right of way of at least 6 m width should be provided closet, one bath and a washing place for three families.
up to the entrance to the cluster to facilitate emergency These shall not be community toilets, as keys to these
vehicle movement up to cluster. toilets shall be only with these three families, making
them solely responsible for the maintenance and
E-2.9 Pedestrian Paths upkeep of these toilets.

Minimum width of pedestrian paths shall be 3 m. E-3 OTHER REQUIREMENTS

E-2.1O Width of Access Between Two Clusters E-3.1 Requirements of Building Design

Built area of dwelling unit within cluster shall have no With the exception of clauses mentioned above,
setbacks from the path or road, space. Hence, the height requirements of building will be governed by the
of the building along the pathway or roads shall be not provision of this Code and good practice [3(1)].
less 60 percent of the height of the adjacent
than E-3.2 Requirements of fwe safety, structural design,
building subject to minimum of 3 m in case of pathway building services and plumbing services shall be as
and 6 m in case of vehicular access. specified in this Code.

ANNEX F

(Clause 12.23)
SPECIAL REQUIREMENTS FOR LOW INCOME HABITAT PLANNING
IN RURAL AREAS

F-1 GENERAL likelihood of natural disasters, natural


drainage, etc.
F-1.l These guidelines cover planning and general
building requirements for low-income houses having c) Identity of the place rooted in its culture and
a maximum built-up area of 40 m2 including future heritage.
expansion, built on notified (as notified by the State d) Nearness and connectivity with nearby urban
Governments) rural areas. The provisions on layout centres.
planning of low-income housing colonies in rural areas e) Occupation related requirements.
are applicable to public and private agencies/ Water management.
f)
government bodies. The provisions of this Code on
d Waste management.
design and construction of buildings for low income
h) Land tenure.
housing in approved layouts are applicable to all private
and public agencies. j) Site selected shall be conveniently
approachable and suitably developed and
F-2 SETTLEMENT AND ENVIRONMENT shall not be subjected to water logging/
PLANNING flooding.
F-2.1 While planning for rural settlements the k) Plot size : 80 m2, Min
following factors shall be taken into consideration: m) Density (Gross) : 60 plots per hectare,
Max
a) Ecosystem and Biodiversity.
n) Minimum frontage : 6m
b) Topography with its direct effect on climate,

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 57


p) Ground Coverage : 33 percent (subject to of both the rooms is not less than 15.5 m2. In
a maximum of 50 incremental housing the bigger room shall always be
percent) the first room.
q) Floor area ratio (FAR): 2, Max F-3.3.1.1 To facilitate incremental housing in case
r) Open spaces : 1.21 hectare open of flatted development or otherwise, habitable space
space for a village at mezzanine level may be permitted. The minimum
with 200 houses. size of such a mezzanine floor should not be lesser
s) Facilities like branch of co-operative bank, a than 6.5 m2 and such a floor should occupy not more
fertilizer depot, a veterinary hospital, market than 50 percent of the room area of which it is a part.
place and a branch of the co-operative Such a mezzanine floor should have appropriate
consumer store besides facilities for openings to facilitate light and ventilation as
educational and health care should be per F-3.5. Minimum clear height below and above
available within a maximum distance of 5 km the mezzanine floor should be 2.4 m and 2.1 m
from any settlement. respectively.
t) Proposed Road Hierarchy As far as possible mezzanine floor should have direct
ventilation from the external face of the building.
Road Road Road Function/Remarks
Where this is not possible ventilation through main
Type Description Width
room may be allowed provided total area of openings
(1) (2) (3) (4)
in the main room is provided taking into consideration .
R 1 Road which 9m Widest road area of mezzanine floor.
connects --
village to Such mezzanine floor may be accessible through the <
nearby areas main room by a ladder, whose minimum angle with
R2 Road which 6m Main village roads vertical plane should be 22%0. Height of the riser
take major with drain on both should be less than 250 mm. 1
traffic to the sides to facilitate
village drainage system of F-3.3.2 Water-Closet/Bathroom
the village
a) The size of independent water-closet shall be
R3 Internal 4.5 m Other village roads
village road 0.9 m2; with minimum width of 90 cm.
R4 Internal 3m Village lanes b) The size of independent bathroom shall be
village road 1.2 mz with minimum width of lm, and
c) The size of combined bath and water closet
F-3 GENERAL BUILDING REQUIREMENTS shall be 1.8 mz with minimum width of 1 m.
(HOMESTEAD)
F-3.3.3 Kitchen
F-3.1 General
The size of a cooking alcove serving as cooking space
The requirements of parts of buildings shall be as given shall’not be less than 2.4 m2 with a minimum width of
in F-3.2 to F-3.7. 1.2 m. The size of individual kitchen shall not be less
than 3.3 m2 with a minimum width of 1.5 m. Semi-
F-3.2 Plinth
open spaces with low walls and roof may also be
The minimum height of plinth shall be regulated on provided for cooking inareas where such provision is
the basis of environmental and topographical condition suitable with respect to climatic comfort. Provision for
and higher plinth height may be required in areas prone smokeless CHULLHA shall be made in all kitchens
to flooding. considering fuel efficiency and health hazard due to
smoke inhalation.
F-3.3 Size of Room
F-3.3.4 Balcony
F-3.3.1 Habitable Room
The minimum width of individual balcony, where
Every dwelling unit to be provided should have at least provided, shall be 0.9 m and shall not be more than
two habitable rooms. Even if one room house is 1.2 m and it shall not project beyond the plot line and
provided initially it should be capable of adding a new on roads or pathway.
second room in future. In a house of two rooms, first
F-3.4 Minimum Height
room shall not be less than 9.0 mz with minimum width
of 2.5 m and second room shall not be less than 6.5 m2 The minimum height of rooms/spaces shall be as
with a minimum width of 2.1 m provided the total area follows:

58 NATIONALBUILDINGCODE OF INDIA
r-”
b

a) Habitable room 2.75 m latrine pan with the pit shall be at least 1.1 m below
b) Kitchen 2.6 m ground level or below the bottom of the water main
2.2 m existing within a distance of 3 m from the pits
c) Bath/water-closet
whichever is more. Construction of such pits may be
d) Corridor 2.1 m
in accordance with [3(4)].
F-3.4.1 In the case of sloping roofs, the average height The water seal latrine should be properly maintained
of roof for habitable rooms shall be 2.75 m and the and kept in sanitary condition by the owner or the
minimum height at eaves shall be 2.10 m. occupier. The contents of the septic tanks, soak pits,
F-3.5 Lighting and Ventilation leach pits, etc, should be periodically emptied.

The openings through windows, ventilators and other The leach pits should be cleaned only after 2 years of
openings for lighting and ventilation shall be as per in their being put out of service after they were full.
accordance with 15.1.2. Location of sanitary facility either as part of the house
NOTE — The windows and other openings shall abut onto or separately shall be decided on the basis of felt
open spaces either through areas left open within the plot or perceptions.
the front, side and rear spaces provided in the layouts which
shall be deemed to be sufficient for light and ventilation F-3.8 The house site shall provide space for storage of
purposes. Wherever ventilatiotiighting is provided by means food grains and keeping cattle. A manure pit having a
of JALI or grill of any material, total area of openings shall minimum area of 1.0 mz shall also be catered for. This
calculated excluding solid portion of the JALI or grill.
will take care of comporting of biodegradable waste.
F-3.6 Stairs
F-4 OTHER REQUIREMENTS
The following criteria shall be adopted for internal
F-4.1 Requirements of fire safety, structural design,
individual staircase:
building services and plumbing services shall be as
a) Minimum width specified in relevant parts of the Code.
1) 2 storeyed-straight 0.60 m F-4.2 One water tap per dwelling unit may be
2) 2 storeyed-winding 0.75 m provided, where adequate drinking water supply is
3) 3 or more storeyed-straight 0.75 m available. If supply is inadequate, public hydrants shall
4) 3 or more storeyed-winding 0.90 m be provided. In the absence of piped water supply, hand
200 mm, Max pumps may be used for provision of water supply.
b) Riser
c) Tread F-4.3 Drainage System
1) 2 storeyed 225 mm, Min
F-4.3.1 Water from drains shall be connected to
2) 3 storeyed or more 250 mm, Min village ponds and appropriate eco-friendly methods
NOTE — Thk could be reduced to 20 cm as the clear trea’d like growing of duck weed plants shall be adopted to
between perpends, with possibility of open riser as well as treat waste water.
nosing and inclined riser to have an effective going of
22.5 cm. F-4.3.2 This treated water may be used for irrigation
and agriculture.
F-3.7 Water Seal Latrine
F-4.4 Appropriate methods (namely conservation,
No building plan shall be approved and no building ground water recharging, rain water harvesting, etc.)
shall be deemed to have been completed and fit for should be employed to ensure effective water
human occupation unless provision is made for water management.
seal latrine. No dry latrine shall be allowed. Water seal
latrines can also be provide on the basis of community F -4.5 Community Fadities
toilets or shared toilets as per the recommendation F-4.5.1 A community halllBARAAT GHAR shall be
given in [3(3)]. established.
Where leaching pits are used, it should be constructed
F-4.5.2 Rural Development Centre shall include
within the premises of the households as it would be
PANCHAYAT GHAR, a MAHILA KENDRA that may
economical as well as facilitate their cleaning. However,
also serve as a vocational training centre.
where, due to space constraint, construction of pits
within the premises may not be possible, pits may be F-4.5.3 School, health centre, post office, police post,
constructed in places like lanes, streets and roads. shopping, work sheds for the artisans, telephone
facilities, etc should also be established.
In case the pit is located under the road, street or foot
path, the inverted level of the pipe connecting the F-4.6 The use (to the extent possible) of locally

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 59


available building materials and cost effective F-4.8 The special needs of women headed households/
substitutes for scarce building materials. Appropriate single and working womenlwoman in difficult
technology inputs shall be introduced for improving circumstances should be addressed. The specific
the local materials or conventional or traditional requirement of women in terms of providing necessary
practices for improved efficiency. facilities in homes to lessen their drudgery would be
given sufficient attention.
F-4.7 The concept of ‘aided self-help’ shall be ensured
for active participation of the prospective users and F-4.9 Protecting and promoting our cultural heritage,
association in the construction and development of architecture and traditional skills should be given due
dwelling units and other community building. importance.

ANNEX G

(Clause 12.24)
SPECIAL REQUIREMENTS FOR DEVELOPMENT PLANNING IN HILLY AREAS

G-1 GENERAL G-1.3 Settlement planning in the hill areas has


extremely large implications on the environment. For
G-1.l These guidelines provides requirements relating planning of the new settlements or working out the
to development planning and design of buildings in strategies for the growth of the existing settlements, it
hilly areas. Any area above 600 m in height form mean ,
is necessary to conduct detailed environmental
sea level may be classified as hilly, or any area with inventory/impact assessment. The inventory would
average slope of 30° may also be classified as hilly, involve geological investigations, slope analysis, soil,
considering the sensitive and fragile eco-system of hills flora and fauna analysis, climatic inventories,
and mountains. However, the State Governments vulnerability to natural disasters, etc. In addition to
may identify and notify areas to be covered under this the aesthetic factors, cultural, architectural and
‘Hilly Area’, which need to be dealt with special historical heritage, scenicflandscape value should also
consideration, when developmental activities are be taken into consideration. Keeping in view the
taken up. scarcity of good buildable land and also the high cost
G-1.2 Hilly areas have one of the most fragile eco- of the construction, it is necessary to optimize the use
systems, which need to be conserved. Therefore ?f land and at the same time, use cost effective,
planning and development strategies for hilly areas appropriate building materials and technologies.
shall have to be designed with added sensitivity and
G-2 LAND USE PLANNING
stress on integrated development. The development
approach shall comprise sound land use planning and G-2.1 The following land use structure shall be
settlement planning. adopted in Development Planning in Hilly areas:

Land Use Percentage of Developed Area

Small Towns Medium Towns Large Cities


(1) (2) (3) ‘ (4)

Residential 50-55 48-52 45-50


Commercial 2-3 2-3 4-5
Industrial 3-4 4-5 5-7
Public and semi-public 8-10 8-10 12-15
Recreational 15-18 15-18 18-20
Transport and commerce 5-6 5-6 6-8
Ecological 8-10 8-10 8-10 n

60 NATIONALBUtLDING CODE OF INDIA


r-

G-3 OPEN SPACES

G-3.1 The following standards shall be adopted in Development Planning in Hilly areas.

Type Area Range Area per 1000 Remarks


Population
(in ha) (in ha)
(1) (2) (3) (4)

Tot lot 0.03-0.05 — Minimum width 15 m


Playground 0.50-1.00 0.12 to 0.20 One for every 5000 may be combined
with schools.
Parks 1.20-2.00 0.12 to 0.20 One for every 10000 population.
City parkslplaygroundslmaidanl — 0.12 to 0.20 For the entire town at one of more sites,
exhibition grounds/cultural depending upon design and space
gathering grounds availability.
Botanical garden 10-20 — One for every town
Recreational complex including zoo 10-12 — One for every settlement with tourist
potential

G-4 ROADS AND PATHS buildings on one side do not shade those on the other
side.
G-4.1 Street orientation shall preferably be East-West
to allow for maximum South sun to enter the buildings. G-4.2 The following road widths shall be adopted for
The street shall be wide enough to ensure that the urban roads in Hilly areas.

Road Type Width (in m)

Open Areas Built-up Areas Plains


(1) (2) (3) (4)
Arterial road 18-24 15-18 50-60
Sub-arterial road 15-18 12-15 30-40
Collector road 9-12 7.5-9 20-30
Local street 4.5-6 3-6 10-20
Loop street (maximum length = 500 m) 4.5 4.5 9
Cul-de-sac (maximum length = 500 m) 4.5 4.5 7.5
Pedestrian path 1.5-2.5 1-1.5 1.5-4.5

G-4,3 Hill Road Manual (IRC:SP:48-1998), a G-5 COMMUNITY FACILITIES AND SERVICES
publication of the Indian Roads Congress shall be
G-5.1 The following standards shall be adopted for
referred to for detailed guidelines for planning roads
community facilities and Services in Hilly areas.
in Hilly areas.

Type Population Distance Area Range


(in ha)
(1] (2) (3) (4)

A. Educational
Primary school 4000 1-2 0.20 to 0.30
Secondary school (10+2) 15000 5-7 0.30 to 0.50
Industrial training centre — 8-12 0.30 to 0.60
College 30000 8-12 2.00 to 3.00

PART 3 DEVELOPMENTCONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 61


Type Population Distance Area Range
(in ha)
(1) (2) (3) (4)

B. Health
Health sub-centre 3000 2-4 0.025 to 0.067
Primary health centre 20000 16-20 0.105 to 0.210
(25-50 beds) 80000 16-20 0.840 to 2.100
Hospital (200-250 beds) 1000 16-20 0.050 to 0.100
Vetenmuy centre

c. Other facilities
Community welfare centre 16000 5-7 0.10 to 0.15
D. Services
Fire station 50000 . 0.30 to 0.80
General post office 50000 10-15 0.20 to 0.40
Post office 10000 5-7 0.10 to 0.15 4
Rural post office 2000 2-4 0.025 to 0.050
Rural post office 1000 1-2 —
Bank (tribal areas) 10000 16-20 0.100 to 0.150
Telephone exchange 50000 10-15 0.20 to 0.40
Electric sub-station (66 kV) — 1.00
Electric sub-station (11 kV) . — 0.05
LPG godown — 0.15

G-6 GENERAL BUILDING REQUIREMENTS G-6.3 Passive Systems for Climatic Control

G-6.1 General G-6.3.1 Appropriate solar passive methods, such as


orientation, double-glazing, trombe walls and solar
The provisions contained in this Part shall
collectors, shall be adopted to achieve climatic comfort
apply excepting for the specific provisions given
with little use of conventional energy.
hereunder.
G-6.3.2 Care shall be taken in siting and design of
G-6.2 Siting buildings to provide passive controls to modify the
G-6.2.1 No house shall preferably be located closer effect of coldhrong winds.
than 1 m to another house. G-6.4 Flat land is normally not available in hilly
G-6.2.2 No house shall be located closer than 10 m regions. ‘Ihe houses are required to be constructed on
to a steep slope. partially sloping land made available by cutting and
filling-. It shall be necessary to protect the house by
G-6.2.3 No house shall be built on a landfill or on the building retaining walls/breast walls [see 3(8)] to avoid
edge of a slope known to have been levelled. landslides occurring at time of earthquakes or heavy
G-6.2.4 Buildings in hills shall be clustered together rains.
to minimise the exposure to cold winds. Open spaces G-6.5 Disaster Resistance
provided shall allow for maximum South sun.
All necessary steps shall be taken in designing and
G-6.2.5 Buildings shall be located on the south slope building in hilly regions to achieve disaster resistance
of a hill or mountain for better exposure to solar as per the relevant codes and Part 6 ‘Structural Design’.
radiation. At the same time, exposure to cold winds All natural disasters likely to affect the locality shall
may be minimized by locating the building on the be taken into consideration, namely earthquakes,
leeward side. cyclones, avalanches, flash floods, landslides etc.

62 NATIONALBUILDING CODE OF INDIA


LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’ Code of practice for sanitation
(4) 12314:1987
in the fulfillment of the requirements of the Code. The for leaching pits for rural
latest version of a standard shall be adopted at the time community
of enforcement of the Code. The standards listed may
(5) 4878:1986 Byelaws for construction of
be used by the Authority as a guide in conformance
cinema buildings (first
revision)
with the requirements of the referred clauses in the Code.
(6) 4838:1990 Anthropometric dimensions for
IS No. Title
school children age group 5-17
(1) 8888 Guide for requirements of low years (second revision)
(Part 1): 1993 income housing: Part 1 Urban (7) 4963:1987 Recommendations for buildings
area (first revision) and facilities for the physically
(2) 3792:1978 Guide for heat insulation of non- challenged (jirst revision)
industrial buildings (first revision)
(8) 14458 Guidelines for retaining walls
11907:1986 Recommendations for calculation for hill area:
of solar radiation on buildings
(Part 1): 1998 Selection of type of wall
(3) 13727:1993 Guide for requirements of cluster
planning for housing (Part 2): 1997 Design of retaining/breast walls

PART 3 DEVELOPMENT CONTROL RULES AND GENERAL BUILDINGREQUIREMENTS 63


-,
(J 6$
CONTENTS

FOREWORD ... 3

1 SCOPE ... 7
2 TERMINOLOGY ... 7
3 FIRE PREVENTION ... 9
4 LIFE SAFETY ... 26
5 FIRE PROTECTION ... 32
6 ADDITIONAL OCCUPANCY-WISE REQUIREMENTS ... 49

ANNEX A CALORIFIC VALUES OF COMMON MATERIALS AND ... 62


TYPICAL VALUES OF FIRE LOAD DENSITY
ANNEX B BROAD CLASSIFICATION OF INDUSTRIAL AND ... 63
NON-INDUSTRIAL OCCUPANCIES INTO DIFFERENT
DEGREE OF HAZARD
ANNEX C FIRE PROTECTION REQUIREMENTS FOR HIGH RISE ... 65
BUILDINGS — 15 m IN HEIGHT OR ABOVE
ANNEX D FIRE PROTECTION CONSIDERATIONS FOR VENTING IN ... 71
INDUSTRIAL BUILDINGS
ANNEX E GUIDELINES FOR FIRE DRILL AND EVACUATION ... 77
PROCEDURES FOR HIGH RISE BUILDINGS
(ABOVE 15 m IN HEIGHT)

LIST OF STANDARDS ... 83

NATIONALBUILDJNGCODE OF INDIA
. ..
y

National Building Code Sectional Committee, CED 46

FOREWORD

This Part of the Code deals with safety from fire. It specifies the demarcation of fwe zones, restrictions on
construction of buildings in each fire zone, classification of buildings based on occupancy, types of building
construction according to fire resistance of the structural and non-structural components and other restrictions
and requirements necessary to minimize danger to life from free, smoke, fumes or panic before the buildings can
be evacuated. The Code recognizes that safety of life is more than a matter of means of exits and accordingly
deals with various matters which are considered essential to the safety of life.

Fire protection techniques have to be based on the fire behaviour characteristics of different materials and structural
elements of buildings. The activities pursued by the occupants of buildings must also be taken into consideration
for assessing the extent of hazards, and method should then be devised by which the hazards could be minimized.
An indefinite combination of variables is involved in the phenomenon of fwe, all of which cannot be quantified.
The requirements of this Code should, therefore, be taken as a guide and an engineering design approach should
be adopted for ensuring a fire safe design for buildings. It would also be necessary for this purpose to associate
qualified and trained fue protection engineers with the planning of buildings, so that adequate fme protection
measures could be incorporated in the building design right from the beginning.

Absolute safety from fire is not attainable in practice. The objective of this Part is to specify measures that will
provide that degree of safety from fire which can be reasonably achieved. The Code endeavors to avoid
requirements that might involve unreasonable hardships or unnecessary inconvenience or interference with normal
use and occupancy of buildings, but insists upon compliance with minimum standards for fue safety necessary in
public interest. For ensuring compliance of fire protection equipments/installations to the laid down quality
requirements, it is desirable to use such equipments/installation duly certified under the BIS Certification Marks
Scheme.

While providing guidelines for minimizing chances of occurrence of fire through passive fire protection measures,
this Part does not intend to cover all aspects of general fire prevention including sources of ignition. Nor does it
cover the prevention of accidental personal injuries during the course of normal occupancy of buildings.

This Part while recognizing that panic in a building on fire maybe uncontrollable, deals with the potential panic
hazard through measures designed to prevent the development of panic. Experience indicates that panic seldom
develops even in the presence of potential danger, so long as occupants of buildings are moving towards exits
which they can see within a reasonable distance and with no obstruction or undue congestion in the path of
travel. However, any uncertainty as to the location or adequacy of means of egress, the presence of smoke or
fumes and the stoppage of travel towards the exit, such as may occur when one P&son stumbles and falls on
stairs, may be conducive to panic. Danger from panic is greater when a large number of people are trapped in a
confined area.
“
Experience has shown that concealed spaces within a building, such as, space betwe6n ceiling and false ceiling,
horizontal and vertical ducts, etc, tend to act as flues/tunnels during a f~e. Provision should, therefore, be made
to provide fire stopping within such spaces.

Nothing in this Part of the Code shall be construed to prohibit better types of building construction, more exits or
otherwise safer conditions than the minimum requirements specified in this Part.

Compliance with this Part shall not be construed as eliminating or reducing the necessity for other provisions for
safety of persons using a building or structure under normal occupancy conditions. Nor shall any provision of
thk Code be construed as requiring or permitting any addition that maybe hazardous under normal occupancy
conditions.

One of the major points brought out in this Part is the limitation of heights and areas of buildings based on fwe
safety of the occupants. Individual municipal corporations are free to alter Table 19 based on local conditions,

PART 4 FIRE ANDLIFE SAFETY 3


?-=”

but the ratios of areas as maintained in the table for different occupancies and types of construction shall be
adhered to.

Advantage has been taken of the developments, particularly in fire resistance rating of materials, designating
types of construction in a rational manner and relating the area limitations of different occupancies to different
types of construction.

Halons (halogenated hydrocarbons) which exhibit exceptional fire fighting and explosion prevention/suppression
characteristics have been found to possess high ozone depleting potential. They come under Group II of Annex
A of the Montreal Protocol on Substances that Deplete the Ozone Layer, the international environmental agreement
for phasing out ozone depleting substances. Due to increasing evidence that the ozone layer is getting depleted at
a faster rate than thought earlier, the developed countries accelerated their phase-out schedule with a view to
achieving 100 percent phase-out of halons by 1 January 1994, instead of the earlier target date of 1 January 2000
after which only essential use of halon was allowed. For developing countries like India, the total phase-out of
halons is to be achieved by 1 January 2010, as per Montreal Protocol, unless a decision is taken in between to
hasten up the phase-out of ozone depleting substances. India, having become a signatory to the Protocol in June
1992, is committed to abide by the Montreal Protocol decisions. In accordance with Ministry of Environment
and Forests, Government of India, Ozone Depleting Substances (Regulations), Rules, 2000, the manufacture of
halon based fire extinguishers and extinguishing systems has been phased out by 1 January 2001. Meanwhile,
the practical implications of the phasing out of the halons cover, by and large, the following aspects:

a) Availability of halons will be restricted;


..-
b) Non-standard halon extinguishers, like aerosol type, shall not be permitted;
c) Discharge of halons for training/testing, etc shall not be permitted;
d) All efforts shall be made for avoiding/minimizing halon emissions at various levels such as production,
fire equipment manufacture, use, service and maintenance;
e) Since ‘drop-in’ substitutes for halons are not likely to be available on a commercial scale in the near
future, wherever possible, instead of halon, use of suitable alternative extinguishing media/methods
will be resorted to, even accepting some trade-offs, if necessary; and
f) Halons shall be restricted for ‘essential uses’ only, for protection of critical fwe explosion risk areas
which would otherwise result in serious impairment of an essential service to society, or pose an
unacceptable threat to life, the environment, or national security.
NOTE — Detailed instructions which will be issued by the Government of India from time-to-time for implementation of the
Country Progrronme for the phasing out of ozone depleting substance (ODS) and regarding permitting use of halons for
applications till tie av~lability of substitutes,shall have to be complied with.
proper
The first version of this Part was formulated in 1970 and first revision was brought out in 1983. Subsequently the
first revision of ‘this Part was modified in 1997 through Amendment No. 3 to 1983 version of the Code. This
modified version of this part included few tables for the fire resistance ratings of various building components,
such as walls, columns, beams and floors. The requirements for wet riser, down-comer, automatic sprinkler
installation, high velocity (10- 15 mls) water spray or foam generating system, etc, for buildings were modified.
Annex giving guidelines for selection of fire detectors had been deleted and relevant Indian Standards on fire
alarm system and smoke detectors had been referred. Also, Annex for determinaticm of f~e loads and flue load
density for arriving at the classification of occupancy hazard and calorific values of some common materials
were included. Annex for broad classification of industrial and non-industrial occupancies into low, moderate
and high hazard had also been included. .

As a result of implementation of this Part, some useful suggestions have emerged. This revision has, therefore,
been prepared to take care of the same. The significant modifications incorporated include:

a) The text has now been divided into the following broad clauses:
1) Fire Prevention — Covering aspects of fire prevention pertaining to design and construction of
buildings on passive fire protection measures, also describing the various types of building materials
and their fire rating.
2) Lije Safety — Covering life safety provisions in the event of fwe and similar emergencies, also
addressing construction and occupancy features that are necessary to minimize danger to life from
fire, smoke, fumes or panic.

NATIONALBUILDING CODE OF INDIA


3) Fire Protection — covering the significant appurtenances and their related components and guidelines
for selecting the correct type of equipment and installation meant for fire protection of the building,
depending upon the classification and type of the building.
b) The classification of building based on occupancy has been elaborated, with:
1) Starred hotels now covered as a new sub-division A-6 under occupancy Group A Residential.
2) Heritage structures and archeological monuments now covered under sub-division D-3 occupancy
Group D Assembly buildings.
3) Mixed assembly occupancies now covered as a new sub-division D-6 and under ground elevated
railways have been covered as a new sub-division D-7 under occupancy Group D Assembly
buildings.
4) TV stations now covered under sub-division E-5 of occupancy Group E Business buildings.
c) The minimum capacity of smoke exhaust equipment has been increased to 12 air changes per hour.
d) For the external stairs for exit requirements, the width and treads have been increased to 1250 mm and
250 mm respectively.
e) Under the requirements for institutional buildings the clear width of all required exits which serve as
egress from hospital or infirmary section has been increased from 1.5 m to 2 m. Also, provision of
patient-lift has been included.
f) Due cognizance of halon phase out programme has been taken, while specifying provisions in this Part
with respect to fire protection using fire extinguishers/systems.

All standards cross-referred to in the main text of this section, are subject to the revision. The parties to agreement
based on this Part are encouraged to investigate the possibility of applying the most recent editions of the
standards.

PART 4 FIRE ANDLIFE SAFETY 5


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 4 FIRE AND LIFE SAFETY

1 SCOPE building immediately above the plinth level. The area


covered by the following in the open spaces is excluded
This Part covers the requirements for fire prevention,
from covered area (see Table 19):
life safety in relation to fire and fire protection of
buildings. The Code specifies construction, occupancy a) garden, rockery, well and well structures,
and protection features that are necessary to minimize plant nursery, waterpool, swimming pool (if
danger to life and property from fire. uncovered), platform round a tree, tank,
fountain, bench, CHABUTARA with open top
2 TERMINOLOGY and unenclosed on sides by walls and the like;
2.0 For the purpose of this Part, the following b) drainage culvert, conduit, catch-pit, gully pit,
definitions shall apply. chamber, gutter and the like;
c) compound wall, gate, unstoreyed porch and
2.1 Automatic Fire Detection and Alarm System
portico, slide, swing, uncovered staircases,
— Fire alarm system comprising components for
ramp areas covered by CHHAJ.JA and the like;
automatically detecting a fire, initiating an alarm of
and
fire and initiating other actions as appropriate.
d) watchman’s booth, pumphouse, garbage
NOTE— The system may also include manual fire alarm call shaft, electric cabin or sub-stations, and such
points.
other utility structures meant for the services
2.2 Automatic Sprinkler System — A system of water of the building under consideration.
pipes fitted with sprinkler heads at suitable intervals and NOTE — For the purpose of this Part, covered area
heights and designed to actuate automatically, control equals the plot area minus the area due for open spaces
in the plot.
and extinguish a fire by the discharge of water.
2.7 Down-comer — An arrangement of fire fighting
2.3 Building — Any structure for whatsoever purpose
within the building by means of down-comer pipe
and of whatsoever materials constructed and every part
connected to terrace tank through terrace pump, gate
thereof whether used as human habitation or not and
valve and non-return valve and having mains not less
includes foundation, plinth, walls, floors, roofs,
than 100 mm internal diameter with landing valves on
chimneys, plumbing and building services, fixed
each floor/landing. It is also fitted with inlet
platforms, VERANDAH, balcony, cornice or projection,
connections at ground level for charging with water
part of a building or anything affixed thereto or any wall
by pumping from fire service appliances and air release
enclosing or intended to enclose any land or space
valve at roof level to release trapped air inside.
and signs and outdoor display structures. Tents,
SHAMIANAHS, tarpaulin shelters, etc, erected for 2.8 Dry Riser — An arrangement of fire fighting
temporary and ceremonial occasions with the permission within the building by means of vertical rising mains
of the Authority shall not be considered as building. not less than 100 mm internal diameter with landing
valves on each floorflanding which is normally dry
2.4 Building, Height of — The vertical distance
but is capable of being charged with water usually by
measured in the case of flat roofs, from the average level
pumping from fire service appliances.
of the ground around and contiguous to the building or
as decided by the Authority to the terrace of the last 2.9 Emergency Lighting — Lighting provided for use
livable floor of the building adjacent to the external wall; when the supply to the normal lighting fails.
and in the case of pitched roofs, up to the point where
2.10 Emergency Lighting System — A complete but
the external surface of the outer wall intersects the
discrete emergency lighting installation from the
finished surface of the sloping root and in the case of
standby power source to the emergency lighting
gables facing the road, the mid-point between the eaves
lamp(s), for example, self-contained emergency
level and the ridge. Architectural features serving no
lumirtaire or a circuit from central battery generator
other function except that of decoration, shall be
connected through wiring to several escape luminaries.
excluded for the purpose of measuring heights.
2.11 Escape Lighting — That part of emergency
2.5 Combustible Material — The material which
lighting which is provided to ensure that the escape
either bums itself or adds heat to a fire, when tested
route is illuminated at all material times, for example,
for non-combustibility in accordance with accepted
at all times when persons are on the premises, or at
standard [4(1 )].
times the main lighting is not available, either for the
2.6 Covered Area — Ground area covered by the whole building or for the escape routes.

PART 4 FIRE ANDLIFE SAFETY 7


2.12 Fire Door — A fire-resistive door approved for and the staircase by fire-resisting doors, and open to
openings in fire separation. the outer air.
2.13 Fire Exit — Away out leading to an escape route 2.23 Fire Resisting Wall — A fire resistance rated
having panic bar hardware provided on the door. wall, having protected openings, which restricts the
spread of fire and extends continuously from the
2.14 Fire Lift — The lift installed to enable fire
foundation to at least 1 m above the roof.
services personnel to reach different floors with
minimum delay, having such features as required in 2.24 Floor Area Ratio (FAR) — The quotient
accordance with this Part. obtained by dividing the total covered area (plinth area)
on all floors by the area of the plo~
2.15 Fire Load — Calorific energy, of the whole
contents contained in a space, including the facings of FM= Total covered area of all floors
the walls, partitions, floors and ceilings. Plot area
2.16 Fire Load Density — Fire load divided by floor 2.25 High Rise Building — For the purpose of this
area. Part, all buildings 15 m or above in height shall be
2.17 Fire Resistance Rating — The time that a considered as high rise buildings.
material or construction will withstand the standard
2.26 Horizontal Exit — An arrangement which
fire exposure as determined by fire test done in .
allows alternative egress from a floor area to another
accordance with the standard methods of fire tests of
floor at or near the same level in an adjoining building
materials/structures.
or an adjoining part of the same building with adequate
-.
2.18 Fh-e Resistance — Fire resistance is a property fire separation.
of an element of building construction and is the
2.27 Means of Egress — A continuous and
measure of its ability to satisfy for a stated period some
unobstructed way of travel from any point in a building
or all of the following criteria:
or structure to a place of comparative safety.
a) resistance to collapse,
2.28 Occupancy or Use Group — The principal
b) resistance to penetration of flame and hot
occupancy for which a building or a part of a building
gases, and
is used or intended to be used; for the purpose of
c) resistance to temperature rise on the unexposed classification of a building according to the occupancy,
face up to a maximum of 180°C and/or an occupancy shall be deemed to include subsidiary
average temperature of 150°C. occupancies which are contingent upon it.
2.19 Fire Separation — The distance in metres
2.29 Plinth Area-The built-up covered area measured
measured from the external wall of the building
at the floor level of the basement or of any storey.
concerned to the external wall of any other building
on the site, or from other site, or from the opposite 2.30 Pressurization — The establishment of a
side of street or other public space for the purpose of pressure difference across a barrier to protect a
preventing the spread of fire. stairway, lobby, escape route or room of a buildlng
from smoke penetration.
2.20 Fire Separating Wall — The wall provides
complete separation of one building from another or 2.31 Pressurization Level — The pressure difference
part of a building from another or part of a building between the pressurized space and the area served by
from another part of the same building to prevent any the pressurized escape route, expressed in pascals (Pa).
communication of fire or heat transmission to wall itself
2.32 Roof Exits — A means of escape on to the roof
which may cause or assist in the combustion of
of a building, where the roof has access to it from the
materials on the side opposite to that portion which
ground. The exit shall have adequate cut-off within ..
may be on fire.
the building from staircase below.
2.21 Fire Stop — A fire resistant material, or
2.33 Site Plot — A parcel (piece) of land enclosed by
construction, having a fiie resistance rating of not lesss
definite boundaries.
than the fiie separating elements, installed in concealed
spaces or between structural elements of a building to 2.34 Stack Pressure — Pressure difference caused
prevent the spread/propagation of fwe and smoke through by a temperature difference creating an air movement
walls, ceilings and like as per the laid down criteria. within a duct, chimney or enclosure.
2.22 Fire Tower — An enclosed staircase which can 2.35 Travel Distance — The distance to be travelled
only be approached from the various floors through from any point in a building to a protected escape route,
landings or lobbies separated from both the floor areas external escape route or final exit.

8 NATIONALBUILDINGCODE OF INDIA
2.36 Ventilation — Supply of outside air into, or the Sub-division A-2 One or two-family private
removal of inside air from an enclosed space. dwellings
Sub-division A-3 Dormitories
2.37 Venting Fire — The process of inducing heat
and smoke to leave a building as quickly as possible Sub-division A-4 Apartment houses (flats)
by such paths that lateral spread of fire and heat is Sub-division A-5 Hotels
checked, fire fighting operations are facilitated and Sub-division A-6 Hotels (Starred)
minimum fire damage is caused.
a) Sub-division A-1 Lodging or rooming houses
2.38 Volume to Plot Area Ratio (VPR) — The ratio — These shall include any building or group
of volume of building measured in cubic metres to the of buildings under the same management, in
area of the plot measured in square metres and which separate sleeping accommodation for
expressed in metres. a total of not more than 40 persons (beds), on
transient or permanent basis, with or without
2.39 Wet Riser — An arrangement for fire fighting dining facilities but without cooking facilities
within the building by means of vertical rising mains for individuals is provided. This includes ims,
not less than 100 mm nominal diameter with landing clubs, motels and guest houses.
valves on each floorflanding for fire fighting purposes
A lodging or rooming house shall be classified
and permanently charged with water from a pressurized
as a dwelling in sub-division A-2 if no room
supply.
in any of its private dwelling units is rented
NOTE — For definitions of other terms, reference shall be to more than three persons.
made to good practice [4(2)].
b) Sub-division A-2 One or two-family private
dwellings — These shall include any private
3 FIRE PREVENTION
dwelling which is occupied by members of
3.1 Classification of Building Based on Occupancy one or two families and has a total sleeping
accommodation for not more than 20 persons.
3.1.1 General Classification
If rooms in a private dwelling are rented to
All buildings, whether existing or hereafter erected outsiders, these shall be for accommodating
shall be classified according to the use or the character not more than three persons per room.
of occupancy in one of the following groups: If sleeping accommodation for more than 20
Group A Residential persons is provided in any one residential
Group B Educational building, it shall be classified as a building in
Institutional sub-division A-1, A-3 or A-4 as the case may
Group C
be.
Group D Assembly
c) Sub-division A-3 Dormitories — These shall
Group E Business
include any building in which group sleeping
Group F Mercantile
accommodation is provided, with or without
Group G Industrial
dining facilities for persons who are not
Group H Storage members of the same family, in one room or
Group J Hazardous a series of closely associated rooms under
joint occupancy and single management, for
3.1.1.1 Minor occupancy incidental to operations in
example, school and college dormitories,
another type of occupancy shall be considered as part
students, and other hostels and military
of the main occupancy and shall be classified under
barracks.
the relevant group for the main occupancy.
d) Sub-division A-4 Apartment houses (flats) —
Examples of buildings in each group are given in 3.1.2 These shall incltfde any building or structure
to 3.1.10. in which living quarters are provided for three
or more families, living independently of each
3.1.2 Group A Residential Buildings
other and with independent cooking facilities,
These shall include any building in which sleeping for example, apartment houses, mansions and
accommodation is provided for normal residential chawls.
purposes with or without cooking or dining or both e) Sub-division A-5 Hotels — These shall
facilities, except any building classified under Group C. include any building or group of buildings
under single management, in which sleeping
Buildings and structures under Group A shall be further
accommodation is provided, with or without
sub-divided as follows:
dining facilities for hotels classified up to
Sub-division A-1 Lodging or rooming houses 4 Star Category.

PART 4 FIRE ANDLIFE SAFETY 9


,

t) Sub-division A-6 Hotels (starred) — These b) Sub-division C-2 Custodial institutions —


shall include the hotels duly approved by the This sub-division shall include any building
concerned authorities as Five Star and above or a group of buildings under single
Hotels. management, which is used for the custody
and care of persons, such as children,
3.1.3 Group B Educational Buildings
convalescents and the aged, for example,
These shall include any building used for school, homes for the aged and infirm, convalescent
college, other training institutions for day-care homes and orphanages.
purposes involving assembly for instruction, education c) Sub-division C-3 Penal and mental institutions
or recreation for not less than 20 students. — This sub-division shall include any
Buildings and structures under Group B shall be further building or a group of buildings under single
sub-divided as follows: management, which !s used for housing
persons under restraint, or who are detained
Sub-division B-1 Schools up to senior secondary for penal or corrective purposes, in which the
level liberty of the inmates is restricted, for
Sub-division B-2 All others/training institutions example, jails, prisons, mental hospitals,
a) Sub-division B-1 Schools up to senior mental sanatoria and reformatories.
secondary level — This sub-division shall 3.1.5 Group D Assembly Buildings
include any building or a group of buildings
under single management which is used for These shall include any building or part of a building,
students not less than 20 in number. where number of persons not less than 50 congregate
-.
or gather for amusement, recreation, social, religious,
b) Sub-division B-2 All others/training
patriotic, civil, travel and similar purposes, for
institutions — This sub-division shall includ~
any building or a group of buildings under example, theatres, motion picture houses, assembly
halls, auditoria, exhibition halls, museums, skating
single management which is used for students
rinks, gymnasiums, restaurants, places of worship, dance
not less than 100 in number.
halls, club rooms, passenger stations and terminals of
In the case of temporary buildings/structures which air, surface and marine public transportation services,
are utilized for educational purposes, the provisions recreation piers and stadia, etc.
of 3.2.5.3 shall apply.
Buildings under Group D shall be further sub-divided
If residential accommodation is provided in the as follows:
schools/institutions, that portion of occupancy shall be
Sub-division D-1 Buildings having a theatrical or
classified as a building in sub-division A-3.
motion picture or any other stage and fixed seats
3.1.4 Group C Institutional Buildings for over 1000 persons
These shall include any building or part thereof, which Sub-division D-2 Buildings having a theatrical or
is used for purposes, such as medical or other treatment motion picture or any other stage and fixed seats
or care of persons suffering from physical or upto 1 000 persons
mental illness, disease or infirmity; care of infants, Sub-division D-3 Buildings without a permanent
convalescents or aged persons and for penal or stage having accommodation for 300 or more
correctional detention in which the liberty of the persons but no permanent seating arrangement.
inmates is restricted. Institutional buildings ordinarily Sub-division D-4 Buildings without a permanent
provide sleeping accommodation for the occupants. stage having accommodation for less than 300
Buildings and structures under Group C shall be further persons with no permanent seating arrangement.
sub-divided as follows: Sub-division D-5 All &her structures including
tempormy structures designed for assembly of
Sub-division C-1 Hospitals and sanatoria
people not covered by sub-divisions D-1 to D-4,
Sub-division C-2 Custodial institutions
at ground level.
Sub-division C-3 Penal and mental institutions
Sub-division D-6 Buildings having mixed
a) Sub-division C-1 Hospitals and sanatoria — occupancies providing facilities such as shopping,
This sub-division shall include any building or
cinema theatres, and restaurants.
a group of buildings under single management,
which is used for housing persons suffering Sub-division D-7 All other structures, elevated or
from physical limitations because of health underground, for assembly of people not covered
or age, for example, hospitals, infirmaries, by sub-divisions D-1 to D-6.
sanatoria and nursing homes. a) Sub-division D-1 — This sub-division shall

10 NA’ITONAL BUILDING CODE OF INDIA


include any building primarily meant for by 3.1.1.1); for keeping of accounts and records and
theatrical or operatic performances and similar purposes, professional establishments, service
exhibitions and which has a raised stage, facilities, etc. City halls, town halls, court houses and
proscenium curtain, freed or portable scenery libraries shall be classified in this group so far as the
or scenery loft, lights, motion picture houses, principal function of these is transaction of public
mechanical appliances or other theatrical business and keeping of books and records.
accessories and equipment and which is
Business buildings shall be further sub-divided as
provided with fixed seats for over 1000 persons.
follows:
b) Sub-division D-2 — This sub-division shall
include any building primarily meant for use Sub-division E-1 Offices, banks, professional
establishments, like offices of architects,
as described for sub-division D-1, but with
engineers, doctors, lawyers and police stations.
fixed seats up to 1000 persons.
c) Sub-division D-3 — This sub-division shall Sub-division E-2 Laboratories, research
include any building, its lobbies, rooms and establishments, libraries and test houses.
other spaces connected thereto, primarily Sub-division E-3 Computer installations.
intended for assembly of people, but which Sub-division E-4 Telephone exchanges.
has no theatrical stage or permanent theatrical
Sub-division E-5 Broadcasting stations and T.V.
andfor cinematographic accessories and has stations.
accommodation for 300 persons or more, for
example, dance halls, night clubs, halls for 3.1.7 Group F Mercantile Buildings
incidental picture shows, dramatic, theatrical These shall include any building or part of a building,
or educational presentation, lectures or other which is used as shops, stores, market, for display and
similar purposes having no theatrical stage sale of merchandise, either wholesale or retail.
except a raised platform and used without
Mercantile buildings shall be further sub-divided as
permanent seating arrangement art galleries
follows:
exhibition halls, community halls, marriage
halls, places of worship, museums, lecture Sub-division F-1 Shops, stores, departmental
halls, passenger terminals and Heritage and stores markets with area up to 500 mz.
Archeological Monuments. Sub-division F-2 Shops, stores, departmental
d) Sub-division D-4 — This sub-division shall stores markets with area more than 500 mz.
include any buiIding primarily intended for Sub-division F-3 Underground shopping centres.
use as described in sub-division D-3, but with Storage and service facilities incidental to the sale
accommodation for less than 300 persons with of merchandise and located in the same building
no permanent seating arrangements. shall be included under this group.
e) Sub-division D-5 — This sub-division shall
3.1.8 Group G Industrial Buildings
include any building or structure permanent
or temporary meant for assembly of people not These shall include any building or part of a building
covered by sub-divisions D-1 to D-4, for or structure, in which products or materials of all kinds
example, grandstands, stadia, amusement park and properties are fabricated, assembled, manufactured
structures, reviewing stands and circus tents. or processed, for example, assembly plants, industrial
f) Sub-division D-6 — This sub-division shall laboratories, dry cleaning plants, power plants,
include any building for assembly of people generating units, pumping stations, fumigation
provided with multiple services/facilities like chambers, laundries, buildings or structures in gas
shopping, cinema theatres and restaurants, for plants, refineries, dairies a,d saw-mills, etc.
example, multiplexes. Buildings under Group G shall be further sub-divided
g) Sub-division D-7 — This sub-division shall as follows:
include any building or structure permanent Sub-division G-1 Buildings used for low hazard
or temporary meant for assembly of people industries.
not covered by D-1 to D-6, for example,
Sub-division G-2 Buildings used for moderate
underground or elevated railways.
hazard industries.
3.1.6 Group E Business Buildings Sub-division G-3 Buildings used for high hazard
These shall include any building or part of a building industries.
which is used for transaction of business (other than The hazard of occupancy, for the purpose of the Code,
that covered by Group F and part of buikhngs covered shall be the relative danger of the start and spread of

PART 4 FIRE AND LIFE SAFETY 11


fire, the danger of smoke or gases generated, the danger 3.1.9 Group H Storage Buildings
of explosion or other occurrences potentially
These shall include any building or part of a building
endangering the lives and safety of the occupants of
used primarily for the storage or sheltering (including
the buildings.
servicing, processing or repairs incidental to storage)
Hazard of occupancy shall be determined by the of goods, ware or merchandise (except those that
Authority on the basis of the fire loads of the contents, involve highly combustible or explosive products
and the processes or operations conducted in or materials) vehicles or animals, for example,
the building, provided, however, that where the warehouses, cold ,storage, freight depots, transit sheds,
combustibility of the material, the flame spread rating storehouses, truck and marine terminals, garages,
of the interior finish or other features of the building hangers, grain elevators, barns and stables. Storage
or structure are such as to involve a hazard greater than properties are characterized by the presence of
the occupancy hazard, the greater degree of hazard shall relatively small number of persons in proportion to
govern the classification. the area. Any new use which increase the number of
For determination of fire loads and fire load density occupants to a figure comparable with other classes of
for arriving at the classification of occupancy hazard, occupancy shall change the classification of the
guidance including the calorific values of some building to that of the new use, for example, hangars
common materials, is given at Annex A. used for assembly purposes, warehouses used for office
purposes, garage buildings used for manufacturing.
A broad classification of industrial and non-industrial
occupancies into low, moderate and high hazard classes 3.1.10 Group J Hazardous Buildings
is given at Annex B, for guidance. Any occupancy not These shall include any building or part of a building
covered in Annex B, shall be classified in the most which is used for the storage, handling, manufacture b-

appropriate class depending on the degree of hazard. or processing of highly combustible or explosive
Where different degrees of hazard of occupancy exist materials or products which are liable to bum with
in different parts of a building, the most hazardous of extreme rapidity and or which may produce poisonous
those shall govern the classification for the purpose of fumes or explosions for storage, handling,
this Code, except in cases where hazardous areas are manufacturing or processing which involve highly
segregated or protected as specified in the Code. corrosive, toxic or noxious alkalis, acids or other liquids
or chemicals producing flame, fumes and explosive,
a) Sub-division G-1 — This sub-division shall poisonous, irritant or corrosive gases; and for the
include any building in which the contents are storage, handling or processing of any material
of such comparative low combustibility and the producing explosive mixtures of dust which result in
industrial processes or operations conducted the division of matter into fine particles subject to
therein are of such a nature that there are hardly spontaneous ignition. Examples of buildings in this
any possibilities for any self propagating fue to class are those buildings which are used foc
occur and the only consequent danger to life
and property may arise from panic, fumes or a) Storage, under pressure of more than
smoke, or fwe from some external source. 0.1 N/mm* and in quantities exceeding 70 m3,
of acetylene, hydrogen, illuminating and
b) Sub-division G-2 — This sub-division shall
natural gases, ammonia, chlorine, phosgene,
include any building in which the contents or
sulphnr dioxide, carbon dioxide, methyloxide
industrial processes or operations conducted
and all gases subject to explosion, fume or
therein are liable to give rise to a fire which
toxic hazard, ~ogenic gases, etc;
will burn with moderate rapidity or result in
other hazardous situation and may give off a b) Storage and handling of hazardous and highly
considerable volume of smoke, but from flammable liquids, liquefiable gases like LPG,
which neither toxic fumes nor explosions are rocket propelltis, etc;
to be feared in the event of fire. c) Storage and handling of hazardous and highly
c) Sub-division G-3 — This sub-division shall flammable or explosive materials (other than
include any building in which the contents or liquids); and
industrial processes or operations conducted d) Manufacture of artificial flowers, synthetic
therein are liable to give rise to a fire which leather, ammunition, explosives and fwworks.
will bum with extreme rapidity or result in NOTE — A list of hazardous substances giving
other hazardous situation or from which quantities, for which or exceeding which owners
poisonous fumes or explosions are to be handling such substances are required to be covered
under the Public Liability Insurance Act, has been
feared in the event of a fire. For fire safety in notified under Government of India, Ministry of
petroleum and fertilizer plant, good practice Environment and Forests Notification No. G.S.R.
[4(3)] may be referred. 347(E) dated 1 August 1996.

12 NATIONAL BUILDING CODE OF INDIA


3.1.11 Any building not covered by Annex B or 3.1.8 or areas which are under development for
shall be classified in the group which most nearly such occupancies.
resembles its existing or proposed use.
3.2.3 Change in the Fire tine Boundaries
3.1.12 Where change in the occupancy of any building
When the boundaries of any fire zone are changed, or
places it in a different group or in a different sub-
when it is intended to include other areas or types of
division of the same group, such building shall be made
occupancies in any fire zone, it shall be done by
to comply with the requirements of the Code for the
following the same procedure as for promulgating new
new group or its sub-division.
rules or ordinances or both.
3.1.13 Where the new occupancy of a building is less
3.2.4 Overlapping Fire Zones
hazardous, based on life and fire risk, than its existing
occupancy, it shall not be necessary to conform to the 3.2.4.1 When any building is so situated that it extends
requirements of the Code for the new group or its sub- to more than one fiie zone, it shall be deemed to be in
division. the fire zone in which the major portion of the building
or structure is situated.
3.1.14 A certificate of occupancy shall be necessary, as
required under Part 2 ‘Administration’, before any change 3.2.4.2 When any buildlng is so situated that it extends
is effected in the character of occupancy of any building. equally to more than one fire zone, it shall be deemed
to be in the fire zone having more hazardous occupancy
3.2 Fire Zones buildings.
3.2.1 Demarcation 3.2.5 Temporary Buildings or Structures
The city or area under the jurisdiction of the Authority 3.2.5.1 Temporary buildkgs and structures shall be
shall for the purpose of the Code, be demarcated into permitted only in Fire Zones No. 1 and 2 as the case
distinct zones, based on fire hazard inherent in the may be, according to the purpose for which these are
buildings and structures according to occupancy to be used, by special permit from the Authority for a
(see 3.1), which shall be called as ‘Fire Zones’. limited period and subject to such conditions as may
be imposed in the permit.
3.2.2 Number and Designation of Fire Zones
3.2.5.2 Such buildings and temporary structures shall
3.2.2.1 The number of fire zones in a city or area under
be completely removed on the expiry of the period
the jurisdiction of the Authority depends upon the
specified in the permit.
existing layout, types of buildlng construction (see 3.3),
classification of existing buildings based on occupancy 3.2.5.3 Adequate fire precautionary measures in the
(see 3.1) and expected future development of the city construction of temporary structures and PANDALS
or area. In large cities or areas, three fire zones maybe shall be taken in accordance with good practice [4(4)].
necessary, while in smaller ones, one or two may be 3.2.6 Restrictions on the Type of Construction for New
adequate. Buildings
3.2.2.2 The fire zones shall be made use of in land use 3.2.6.1 Buildings erected in Fire Zone No. 1 shall
development plan and shall be designated as follows: conform to construction of Type 1, 2, 3 or 4.
a) Fire Zone No. 1 — This shall comprise areas 3.2.6.2 Buildings erected in Fire Zone No. 2 shall
having residential (Group A), educational conform to construction of Type 1, 2 or 3.
(Group B), institutional (Group C), and
3.2.6.3 Buildings erected in Fire Zone No. 3 shall
assembly (Group D), small business (Sub-
conform to construction of Type 1 or 2.
divisions E-1 ) and retail mercantile (Group F)
buildings, or mess which zweunder development 3.2.7 Restrictions on Existhg Buildings
for such occupancies. The existing buildings in any fire zone shall not be
b) Fire Zone No. 2 — This shall comprise required to comply with the requirement of the Code
business (Sub-divisions E-2 to E-5) and unless these are altered, or in the opinion of the
industrial buildings (Sub-division G-1 and Authority, such building constitutes a hazard to the
G-2), except high hazard industrial buildings safety of the adjacent property or the occupants of the
(Sub-division G-3) or areas which are under building itself or is an unsafe building. In the event of
development for such occupancies. alteration, it shall be necessary to obtain permission
c) Fire Zone No. 3 — This shall comprise areas of the Authority for such alteration consistent with fire
having high hazard industrial buildings (Sub- hazard (see Part 2 ‘Administration’).
division G-3), storage buildings (Group H) Alterations/modifications/renovations shall be
and buildings for hazardous used (Group J) accomplished so as to ensure conformity with all the

PART 4 FIRE AND LIFE SAFETY 13


‘p=

safety requirements of the new buildings. Such Type 1 Construction, Type 2 Construction, Type 3
alterations shall not in anyway bring down level of Construction and Type 4 ‘Construction’. The fire
fire and life safety below that which existed earlier. resistance ratings for various types of construction for
Any addition or alterations or construction of cubicles structural and non-structural members shall be as given
or partitioning for floor area exceeding 500 mz for all in Table 1.
high rise buildings shall be with approval of local fire
For buildings 15 m in height or above non-combustible
authority.
materials should be u$ed for construction and the
3.3 Types of Construction internal walls of staircase enclosures should be of
3.3.1 General brick work or reinforced concrete or any other
material of construction with minimum of 2 h rating.
The design of any building and the type of materials
The walls for the chimney shall be of Type 1 and
used in its construction are important factors in making
Type 2 Construction depending on whether the gas
the building resistant to a complete burn-out and in
temperature is above 200”C or less.
preventing the rapid spread of fire, smoke or fumes,
which may otherwise contribute to the loss of lives 3.3.2 It is required that an element/component shall
and property. have the requisite fire resistance rating when tested in
The fire resistance of a building or its structural and acco’’rdance with the accepted standard [4(1)].
non-structural elements is expressed in hours against Tables 2 to 18 provide available data regarding fire
a specified fire load which is expressed in kcaUm2, and resistance ratings of various building components such
against a certain intensity of fire. The fire-resistance as walls, columns, beams and floors. Fire damage
test for structural element shall be done in accordance assessment, post fwe structural safety assessment of
with good practice [4(5)]. For the purpose of the Code, various structural elements of the building and
the types of construction according to fire resistance adequacy of the structural repairs can be done by the
shall be classified into four categories, namely, fwe resistance ratings mentioned in Tables 2 to 18.

Table 1 Fire Resistance Ratings of Structural and Non-Structural Elements (Hours)


(Clause 3.3.1)

S1 Stmctural Element Type of Construction


No. ~
Type 1
(1) (2) (3) (4) (5) (6)
O Exterior walls:
a) Fire separation less than 3.7 m a) Bearing 4 2 2 1
b) Non-bearing 2 1% 1 1
b) Fire separation of 3.7 m or more a) Bearing 4 2 2 1
but less than 9 m b) Non-bearing 1% 1 1 1
c) Fire separation of 9 m or more a) Bearing 4 2 2 1
b) Non-bearing 1 1 1 1
ii) Fire resisting wstls 4 2 2 2
iii) Fire separation assemblies (like fme 4 2 2 2
check doors)
iv) Fire enclosures of exitways, hallways 22 2 2
and stairways
v) Shaft other than exitways, elevator 2’2 2 2
and hoistways
/
vi) Exitway access corridors 1 1 1 1
vii) Vertical separation of tenant spaces 1 1 1 1
viii) Dwelling unit separation 1 1 1 1
Non-load bearing partitions — At least half an hour —
ix) Interior bearing walls, Iw+ring a) Supporting more than one floor 4 2 2 2
partitions, columns, girders, trusses b) Supporting one floor only 3 11~ 1 1
(other than roof trusses) and framing c) Supporting a roof only 3 1% 1 1
x) Structural members support walls 3 1% 1 1
xi) Floor constnrction including watls 3 145 1 1
xii) Roof construction a) 5 m or less in height to lowest member 2 ly2 1 1
b) More than 5 m but less than 6.7 m in 1 1 1 1
height to lowest member
c) 6.7 m or more in height to lowest 0 0 0 0
member

14 NATIONAL BUILDING CODE OF INDIA


Table 2 Masonry Walls: Solid (Required to Resist Fire from One Side at a Time)
(Clause 3.3.2)

S1 Nature of Construction Minimum Thickness (mm), Excluding any Finish for a


No. and Materials Fire Resfatance (Hours) of
/ .
Load Bearing Non-load Bearing
~~
1 1y2 2 3 4 1 l% ‘2 3 4
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12)

i) Reinforced) cement concrete 120 “ ‘- ‘-- Zw


‘-- ‘“-
Mu
(25)2] gyz) ~J:2) (25)2) (25)2)
ii) Unreinforced cement concrete 150 175
iii) No-fines concrete with :
a) 13 mm cement/sand or gypsundsand — 150 150 150 150 150
b) 13 mm light weight aggregate gypsum — 150 150 150 150 150
plaster
iv) Bricks of clay:
a) Without finish 90 100 100 170 170 75 90 100 170 170
b) With 13 mm lightweight aggregate 90 90 90 100 100 75 90 90 90 100
gypsum plaster
v) Bricks of sand lime
a) Without finish 90 100 100 190 190 75 90 100 170 170
b) With 13 mm lightweight aggregate 90 90 90 100 100 75 90 90 90 100
gypsum plaster
vi) Blocks of concrete:
a) Without finish 90 100 100 — — 75 90 1043 140 150
b) With 13 mm lightweight aggregate 90 90 90 100 100 75 75 75 90 100
gypsum plaster
c) With 13 mm cement/sand or gypsum/ 75 90 90 100 140
sand
vii) Blocks of lightweight concrete:
a) Without finish 90 100 1(KI 140 150 75 75 75 125 140
b) With 13 mm lightweight aggregate 90 90 90 100 100 50 63 75 75 75
gWsum plaster
c) With 13 mm cementkcnd or gypsum/ — . — . — 75 75 75 90 100
sand
viii) Blocks of aerated concrete:
a) Without finish 90 100 100 140 180 50 63 63 75 100
b) With 13 MM lightweight aggregate 90 90 100 100 150
gypsum plaster

‘) Walls cOnttining at least 1 percent of vertical reinforcement.


2)~inim~ thickness of actual cover to reinforcement.

Table 3 Masonry Walls: Hollow (Required to Resist Fire from One Side at a Time)
(Clause 3.3.2)

SI Nature of Construction Minimum Thickness (mm), Excluding any Finish for a


No. and Materials Fire Resistance (Hours) of
J
—
. \

Load Bearing ~on-load &3uirtg

(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13)

i) Bricks of clay:
a) Without finish 170 170 170 2041 200 75 75 90 100 170-:’170
b) With 13 mm lightweight aggregate 100 100 170 170 170 75 75 90 90 90 100
gypsum plaster
ii) Blocks of concrete:
a) Without finish 90 125 125 140 140 150
b) With 13 MM cement/sarrcf or gypsrrrn/sand 190 200 200 — — 90 125 125 140 140 140
c) Whfr 13 mm fightweight aggregate 75 90 90 100 125 125
gypsum plaster
iii) Blocks of lightweight concrete:
a) Without finish 100 100 100 — — 75 90 90 100 140 150
b) With 13 mm cementhand or gypsrrnr/sand . — — — — 75 75 75 100 140 140
c) With 13 mm lightweight aggregate — — — — 63 63 63 75 90 100
gypsum plaster

PART 4 FIRE AND LIFE SAFETY 15


Table 4 Framed Construction, Load Bearing (Required to Resist Fire
from One Side at a Time)
(Clause 3.3.2)

S1 Nature of Construction and Materials/Timber Studs at Centres not Minimum Thickness (mm) of Protection
No. Exceeding 600 mm, Facwi on Each Side with for a Fire Resistance of lh

(1) (2) (3)

i) Plasterboard layers with joints staggered, joints in outer layer taped and filled — Total 25
thickness for each face
4,
ii) One layer of 12.7 mm plasterboard with a finish of lightweight aggregate gypsum 13
plaster

iii) Metal lath and plaster, thickness of plaster:

a) Sanded gypsum plaster (metal lathing grade) 22


b) Lightweight aggregate gypsum plaster 13

Table 5 Framed Construction, Non-Load Bearing (Required to Resist Fire


from One Side at a Time)
(Clause 3.3.2)

Nature of Construction and Materials/Steel or Timber Frame at Stud Minimum Thickness (mm) of Protection
Centres not Exceeding 600 mm, Facings on Both Sides of Construction for a Fire Resistance
/ 3

%h lh l%h 2h
(1) (2) (3) (4) (5) (6)

A) Dry lining with materials fixed direct to studs


(without plaster finish)

1. One layer of plasterboard with taped and filled joints Timber or steel 12.7
2. Two layers of plasterboard with joints staggered, joints in Timber or steel 19 25
outer layer taped and filled — Total thickness for each face
?
3. One layer of asbestos insulating board with transverse joints Timber or steel 9 12
backed by fillers of asbestos insulating board not less than 9 J
mm thick, or by-timber
4. One layer of wood wool slabs Timber 25
5. One layer of chipboard or of plywood Timber or steel 18

B) Lining with materials fixed direct to suds, with plaster finish:


Plasterboard of thickness: Timber or steel
a) With not less than 5 mm gypsum plaster finish 9.5
b) With not less than 13 mm gypsum plaster finish 12.7

C) Wet finish:
Metal lath and plaster, thickness of plaster:
a) Sanded gypsum plaster Timber or steel 13
b) Lightweight aggregate gypsum plaster Timber 13 19 25

Steel 13

Table 6 Framed External Walls Load Bearing (Required to Resist Fire


from One Side at a Time)
(Clause 3.3.2)

S1 Nature of Construction and Materials Minimum T&knew (mm) of Protection


No. for a Fire Resistance of 1 h
(1) (2) (3)

Timber studs at centers not exceeding 600 mm with internal linings of:

i) Plasterboard layers with joints in outer layer taped and filled, total thickness of 25
plasterboard

16 NATIONAL BUILDING CODE OF INDIA


Table 9 Framed Wails Non-Load Bearing Required to Resist Fire only from Inside the Building (C)
(Clause 3.3.2)

Nature of Construction and Materiafs Minhtmm Thickness (mm) of Protection for a


Fire Resistance of 1?/2h
(1) (2)
Timber frame with external cladding of weather boarding or external plywood,
9.5 mm with an internal lining of
1. Plasterboard not less than 9.5 mm thick, finished with:
a) Gypsum plaster 13
b) Lightweight aggregate gypsum plaster 10
2. Plasterboard not less than 12.7 mm thick, finished with:
a) Gypsum plaster 10
b) Lightweight aggregate gypsum plaster 10
3. One layer of asbestos insulating board with transverse joints backed by fdlers 9
of asbestos insulating board not less than 9 nun thick or by timber 12
t

Table 10 Reinforced Concrete Columns


(Clause 3.3.2)

SI Nature of Construction and Materiafs Mhdnmm Dimensions (mm) Excluding auy Fhdsh,
No. for a I&e Reaistmtee of
/ -
?hh lh 1% h 2h 3h 4h
(1) (2) (3) (4) (5) (6) (7) (8)

i) Fully exposed Width 150 200 250 300 400 450


cover 40 40 40 40 40 40
ii) 50 percent exposed Width 125 160 200 200 300 350
cover 40 40 40 40 40 40
iii) One face exposed Thickness 100 120 140 160 200 240
Cover 40 40 40 40 40 40

Table 11 Concrete Beams


(Clause 3.3.2)

SI Nature of Construction and Materhds Minimum Di?nenakms (mm) Excluding any Finish,
No. for a Fire Redstance of
6
- \
%h lh 1%h 2h 3h 4b
(1) (2) (3) (4) (5) [6) (7) (8)

i) Reinforced concrete (simply supported) Width 200 200 200 200 240 280
601) 7.01)
Cover 20 20 20 40
ii) Reinforced concrete (continuous) Width 200 200 200 200 240 280
Cover 20 20 20 30 40 5(JI)
iii) Prestressed concrete (simply supported) Width 100 120 150 200 240 280
Cover 25 40 55 70 80 90
iv) Prestressed concrete (continuous) Width 80 100 120 150 200 240
Cover 20 30 40 55 70 80

1I Requhe attention to tie additional measures necessary to reduce the risk of sP~fing.

Table 12 Concrete Floors


(Clause 3.3.2)

S1 Nature of Construction and Materials Minimum Dimensions (mm) Excluding any Finiih,
No. for a Elre Resistance of
e
- \
1/2h lh l%h 2h 3h 4h
(1) (2) (3) (4) (5) (6) (7) (8)
i) Reinforced concrete (simply supported) Thickness 75 95 110 125 150 170
Cover 20 20 25 35 451) 551)
ii) Reinforced concrete (continuous) Thickness 75 95 110 125 150 170
Cover 20 20 20 25 35 451)

1)Require attention to the ~dirional measures necessary to reduce the risk of sPsfling.

18 NATIONAL BUILDING CODE OF INDIA


Table 13 Concrete Floors: Ribbed Open sof!lt
(Clause 3.3.2)

S1 Nature of Construction and Materials Mfnfmurn Dimensions (mm) Excluding any Firdsh,
No. for a Fire Resistance of
A
-
1/2h lh l%h 2h 3h 4h
(1) (2) (3) (4) (5) (6) (7) (8)

i) Reinforced concrete (simply supported) Thickness of flea 75 95 110 125 150 170
Rib width 125 125 125 125 150 175
Cover 20 20 35 45 55 65

ii) Reinforced concrete (continuous) Thickness 75 95 110 125 150 170


Width 125 125 125 125 150 175

Cover 20 20 20 35 45 55
\

Table 14 Encased Steel Columns, 203 mm x 203 mm


(Protection Applied on Four Sides)
(Clause 3.3.2)

Nature of Construction and Materials Mirdrnarn Dimensions (nun) Excluding any Finish,
for a Fire Resistance of
A
/ -
lh l%h 2h 3h 4h

(1) (2) (3) (4) (5) (6)


A) Hollow protection (without an air cavity over the flanges):

1. 1)Met~ lathing With tmwelled lightweight aggregate gYPsmn plaster 13 15 20 32


2. Plasterboard with 1.6 mm wire binding at 100 mm pitch, finished with
lightweight aggregate gypsum plaster not less than the thickness
specified:
a) 9.5 mm plaster board 10 15
b) 19 mm plaster board 10 13 20
3. Asbestos insulating boards, thickness of board
a) Single thickness of board, with 6 mm cover fillets at transverse 19 25
joints
38 50
b) Two layers, of totaf thickness
4. Sofid bricks of clay, composition or sand lime, reinforced in every 50 50 50 75 100
horizontal joint, unplastered
5. Aerated concrete blocks 60 60 60
6. Solid blocks of lightweight concrete hollow protection (with an air 50 50 50 60 75
cavity over the flanges)
B) Asbestos insulating board screwed to 25 mm asbestos battens 12 19

C) Solid protections

1. Concrete, not leaner than 1:2:4 mix (unplastered):


a) Concrete not assumed to be load bearing, reinforced 2) 25 25 25 50 75

b) Concrete assumed to be load bearing 50 50 50 75 75

2. Lightweight concrete, not leaner than 1:2:4 mix (unplastered): concrete 25 25 25 40 60


not assumed to be load baring, reinforced 2)

1) So fixed or designed, as to aflow frrfl penetration for mecbCrIic~ bond.


Z)ReinforWment sh~l consist of s~el bfiding w~e not less ~~ 2.3- ~ ~c~ess, or a stil mesh w@thlg not kss @ ().5kg/m2. h
concrete protection, the spacing of that rcin~orcement shall not exceed 200 mm in any direction.

PART 4 FIRE AND LIFE SAFETY 19


Table 15 Encased Steel Beams, 406 mm x 176 mm (Protection Applied on Three Sides)
(Clause 3.3.2)

Nature of Construction and Materials Mhimum Thickness (mm) of Protection for a


Fire Resistance of

1/2 h lh l%h 2h 3h 4h-


(1) (2) (3) (4) (5) (6) (7)

A) Hollow protection (without an air cavity beneath the lower flange):


1, 11Met~ lathing with rrowelled lightweight aggregate gypsumPlaster 13 13 15 20 25
2. Plasterboard with 1.6 mm wire bindingz) at 100 mm pitch, finished
with lightweight aggregate gypsum plaster not less than the
thickness specified:
a) 9.5 mm plaster board 10 10 15
b) 19 mm plaster board 10 10 13 20
3. Asbestos insulating hoards, thickness of board:
a) Single thickness of board, with 6 mm cnver fillets at transverse 19 25
joints
b) Two layers, of total thickness 38 50
B) Hollow protection (with an air cavity below the lower flange):
1. Asbestos insulating board screwed to 25 mm asbestos battens 9 12
C) Solid protection:
1. Concrete, not leaner than 1:2:4 mix (unplastered):
a) Concrete not assumed to be load bearing, reinforced 3) 25 25 25 25 50 75
b) Concrete assumed to be load bearing 50 50 50 50 75 75
2. Lightweight concrete), not leaner than 1:2:4 (mix) unplastered 25 25 25 25 40 60

‘) So fixed or designed, as to aflow full penetration for mechanical bond.


“ Where wire binding cannot be used, expert advice should be sought regarding alternative methods of support to enable the lower edges
of the plasterboard to be fixed together and to the lower flange, and for the top edge of the plasterboard to he held in position.
31Reinforcement shall consist of steel bhding wire not less than 2.3 mm in thickness or a .Wd * * ~ less ~ 0.5 Wm2. ~
concrete protection, the spacing of that reinforcement shall not exceed 200 tnrn its any direCtiOtl.
4) concrete not assum~ to he load bearing, reinforced.

Table 16 Timber Floors — Tongued and Grooved Boarding, or Sheets of Tongued and Grooved
Plywwd or Wood Chipboard, of not Less than 21 mm I@ished ~
(Clause 3.3.2)

Nature of Construction and Materials Mild&m TMc&aS$ (mm)&Protdon Fora


FireWst@aRmef
* \
/
%h lh 2h
(1) (2) (3) (4)

37 mm (minimum) timber joists with a ceiling of

1. Timber lathing and plaster, plaster of thickness 15


2. Metal lathing and plaster, thickness of plaster
a) Sanded gypsum plaster (metal lathing grade) 15
b) Lightweight aggregate gypsum plaster 13 13 25
3, One layer of plasterboard with taped and filled joints 12.7
4, Two layers of plasterboard with joints staggered, joints in outer layer 19 31
raped and filled totaf thickness
5. One layer of plasterboard not less than 9.5 mm thick, finished witk
a) Gypsum plaster 5
b) Sanded gypsum plaster 13
c) Lightweight aggregate gypsum plaster 13
6. One layer of plasterboard not less than 12.7 mm thick, finished with:
a) Gypsum plaster 5
b) Lightweight aggregate gypsum plaster 10
7. One layer of asbestos insulating board with any transverse joints 9 12
backed by fillets of asbestos insulating board not less than 9 mm
thick or by timber

20 NATIONAL BUILDING CODE OF INDIA


Table 17 Timber Floors — Tongued and Grooved Boarding, or Sheets of Tongued and Grooved
Plywood or Wood Chipboard, of not Less than 15 mm Finished Thickness
(Clause 3.3.2)

Nature of Construction and Materials Mirdmum Thickness (mm) of Protection for a


Fire Resistance of

l%h Ih 2h
(1) (2) (3) (4)

37 mm (minimum) timber ioists with a ceiling of


1. Timber lathing and plaster, plaster of thickness 15
2. Metal lathing and plaster, thickness of plaster for
a) Sanded gypsum plaster (metal lathing grade) 15
b) Lightweight aggregate gypsum plaster 13 13 25
3. One layer of plasterboard with taped and filled joints 12.7
4. Two layers of plasterboard with joints staggered, joints in outer layer taped 22 31
and filled total thickness
5. One layer of plasterboiu’d not less than 9.5 mm thick, finish with:
a) Gypsum plaster 5
b) Sanded gypsum plaster 15
c) Lightweight aggegate gypsum plaster 13
6. One layer of plasterboard not less than 12.7 mm thick, finished with:
a) Gypsum plaster 5
b) Lightweight aggregate gypsum plaster 10
7. One layer of asbestos insulating board, with any transverse joints backed by 9 121)
fillets of asbestos insulating bored not less than 9 mm thick, or by timber

0 Finished on toP with 25 mm minimum thick glass fibre or mineral wool laid between jOb.

Table 18 Timber Floors — Any Structurally Suitable Flooring of


Timber or Lignocelhdoses Boards
(Clause 3.3.2)

Nature of Construction and Materials Minimum TIdckness (mm) of Protection for a


Fire Resistance of
~

(1) (2) (3)

37 mm (minimum) timber joists with a ceiling of


1. Timber lathing and plaster, plaster of thickness 15
2. Metal lathing and plaster, thickness of plaster fon
a) Sanded gypsum plaster (metal lathing grade) 15
b) Lightweight aggegate gypsum plaster 13 19
3. One layer of plasterboard with joints taped and filled and backed by timber 12.7
4. Two layers of plasterboard with joints staggered, joints in outer layer taped 25
and filled total thickness
5. Two layers of plasterboard, each not less than 9.5 mm thick, joints between 5
boards staggered and outer layer finished with gypsum plaster
6. One layer of plasterboard not less than 9.5 mm thick, finish with:
a) Sanded gypsum plaster 13
b) Lightweight aggregate gypsum plaster 15
7. One layer of plasterboard not less than 12.7 mm thick, finished with:
a) Sanded gypsum plaster 15
b) Lightweight aggregate gypsum plaster 13
8. One layer of asbestos insulating board with any transverse joints backed by 12
fillets of asbestos insulating board not less than 9 mm thick, or by timber

3.3.3 Steel Construction of fire. This could be achieved by use of appropriate


Load hearing steel beams and columns of buildings methodology using suitable fire resistance rated
having total covered area of 500 m2 and above shall be materials alongwith suppression system {see Table 14,
protected against failure/collapse of structure in case Table 15 and also accepted standard [4(5)]}.

PART 4 FIRE AND LIFE SAFETY 21


3.4 General Requirements of All Individual Table 19 (see also Part 3 ‘Development Control Rules
Occupancies and General Building Requirements’ ).

3.4.1 General Table 19 Comparative Floor Area Ratios for


All buildings shall satisfy certain requirements which Occupancies Facing One Public Street
contribute, individually and collectively, to the safety Atleast 9 m Wide
of life from fire, smoke, fumes and panic arising from (Clauses 2.6 and 3.4.5)
these or similar causes. There are, however, certain
general principles and common requirements which Occupancy Type of Construction
Classification t A Y
are applicable to all or most of the occupancies. Type 1 Type 2 Type 3 Type 4
3.4.2 Exceptions and Deviations (1) (2) (3) (4) (5)

Exceptions and deviations to the general provisions of Residential UL 2.0 1.4 1.0
Educational UL 2.0 1.4 1.0
requirements of individual occupancies are given as
Institutional UL 1.5 1.0 0.8
applicable to each type of occupancy in 6.1 to 6.9. In Assembly UL 1.0 0.7 0.5
case of practical difficulty or to avoid unnecessary Business UL 2.9 2.3 1.6
hardship, without sacrificing reasonable safety, the Mercantile 8.0 1.8 1.4 1.0
Authority may grant exemptions from the Code. Industrial 7.5 1.9 1.6 1.3
Storage(see Note 5) 6.0 1.5 1.3 1.0
3.4.3 Occupation of Buildings under Construction Hazardous(see Note 5) 2.8 1.1 0.9 NP

3.4.3.1 A building or portion of the building may be UL — Unlimited.


occupied during construction, repairs, alterations or NP — Not permitted.
additions only if all means of exit and fire protection NOTES
measures are in place and continuously maintained for 1 The FAR values given in this table are subject to overall
the occupied part of the building. restrictions on the heights of buildings in the case of
educational, institutional, assembly, storage and hazardous
3.4.3.2 A high rise building during construction shall occupanciesas specifiedin CO12 of Table 23.
be provided with the following fire protection 2 This table has been prepared, taking into account the
measures, which shall be maintained in good working combustible content in the different occupancies as well as
the ftre resistanceoffered by the type of construction.
condition at all the times:
3 This table shouldbe modifiedby the Authority,taking into ,
a) Dry riser of minimum 100 mm diameter pipe accountthe other aspects as given below: ,,
4

with hydrant outlets on the floors constructed a) Densityin terms of dwellingunits per hectare;
with a fire service inlet to boost the water in the b) Traffic considerations;
dry riser and maintenance should be as per the c) Parking spaces;
requirements laid down in good practice [4(6)]. d) Local fire fighting facilities;and
e) Water supply, drainage and sanitationrequirements.
b) Drums tilled with water of 2000 litres capacity
4 The FAR values specified in this table may be increased
with two fiie buckets on each floor; and by 20 percent for the following services:
c) A water storage tank of minimum 20000 @ A basement or cellar space under a building constructed
litres capacity, which may be used for other on stilts and used as a parking space and air-
construction purposes also. conditioning plant room used as accessory to the
principal use;
3.4.4 Maximum Height b) Watchman’s booth, pumphouse, garbage shaft, electric
cabin or sub-station and other utility structures meant
Every building shall be restricted in its height above for the services of the building under considerations;
the ground level and the number of storeys, depending c) Projections and accessory buildings as specifically
upon its occupancy and the type of construction. The exempted under the Code; and
height shall be measured as specified in Part 3 d) Staircase room and lift rooms above the topmost storey;
‘Development Control Rules and General Building architectural feature; and chimneys and elevated tanks
of dimensions as permissible under the Code; the area
Requirements’. The maximum permissible height of the lift shaft shall be taken only on one floor.
for any combination of occupancy and types of 5 In so far as single storey storage and hazardous occupancies
construction should necessarily be related to the width are concerned, they would be farther governed by volume to
of street fronting the building, or floor area ratios and plot area ratio (VPR) to be decided by the Authority.
the local fire fighting facilities available.
3.4.5.1 Each portion of a building, which is separated
3.4.5 Floor Area Ratio
by one or more continuous fire resisting walls, having
The comparative floor area ratios for different a fire resistance of not less than 2 h, extending from
occupancies and types of construction are given in the foundation to 1 m above the roof at all points, may

22 NATIONALBUILDING CODE OF INDIA

;
t
be considered to be a separate building for the protected with a fire-resisting assembly as specified
calculation of maximum permissible height and floor in 3.4.9.
area, provided openings, if any, in the separating
3.4.8.2 For Type 4 construction, openings in the
wall are also protected by fire assemblies of not less
separating walls or floors shall be fitted with 2 h fire-
than 2 h.
resisting assemblies.
3.4.6 Open Spaces
3.4.8.3 Openings in walls or floors which are
The open spaces around or inside a building shall necessary to be provided to allow passages of all
conform to the requirements of Part 3 ‘Development building services like cables, electrical wirings,
Control Rules and General Building Requirements’. telephone cables, plumbing pipes, etc, shall be
protected by enclosure in the form of ducts/shafts
3.4.6.1 For high rise buildings, the following
having afire resistance not less than 2 h. The inspection
additional provkions of means of access to the building
door for electrical shafts/ducts shall be not less than
shall be ensured (see Part 3 ‘Development Control
2 h and for other services shafts/ducts, the same shall
Rules and General Building Requirements’):
have fire resistance not less than 1 h. Medium and low
a) The width of the main street on which the voltage wiring running in shafts/ducts, shall either be
building abuts shall not be less than 12 m and armoured type or run through metal conduits. Further,
one end of this street shall join another street the space between the conduits pipes and the walls/
not less than 12 m in width; slabs shall be filled in by a filler material having fke
b) The road shall not terminate in a dead end; resistance rating of not less than 1 h.
except in the case of residential building, up NOTE— In the case of buildings where it is necessmy to lower
to a height of 30 m. or lift heavy machinery or goods from one floor to the other, it
may be necessary to provide larger openings in the floor. Such
c) The compulsory open spaces around the
openings shall be provided with removable covers which shall
building shall not be used for parking; and have the same strength and fire resistance as the floor.
d) Adequate passageway and clearances
3.4.8.4 Vertical opening
required for fire fighting vehicles to enter the
premises shall be provided at the main Every vertical opening between the floors of a building
entrance; the width of such entrance shall be shall be suitably enclosed or protected, as necessary,
not less than 4.5 m. If an arch or covered gate to provide the following:
is constructed, it shall have a clear head-room
a) Reasonable safety to the occupants while
of not less than 5 m.
using the means of egress by preventing
3.4.7 Mixed Occupancy spread of fire, smoke, or fumes through
vertical openings from floor to floor to allow
When any building is used for more than one type of
occupants to complete their use of the means
occupancy, then in so far as fire safety is concerned, it
of egress. Further it shall be ensured to
shall conform to the requirements for the occupancies
provide a clear height of 2 100 mm in the
of higher hazard. Unless the high hazard area is
passage/escape path of the occupants.
separated by separating walls of 4 h rating, the
b) Limitation of damage to the building and its
occupancies shall not be treated individually.
contents.
3.4.8 Openings in Separating Walls and Floors
3.4.9 Fire Stop or Enclosure of Openings
At the time of designing openings in separating walls
Where openings are permitted, they shall not exceed
and floors, particular attention shall be paid to all such
three-fourths the area ~f the wall in the case of an
factors as will limit fire spread through these openings
external wall and they shall be protected with fire
and maintain fire rating of the structural member.
resisting assemblies or enclosures having a fire
3.4.8.1 For Types 1 to 3 construction, a doorway or resistance equal to that of the wall or floor in which
opening in a separating wall on any floor shall be these are situated. Such assemblies and enclosures shall
limited to 5.6 m2 in area with a maximum heightiwidth also be capable of preventing the spread of smoke or
of 2.75 m. Every wall opening shall be protected with fumes through the openings so as to facilitate the safe
fire-resisting doors having the fire rating of not less evacuation of building in case of a fire {see also
than 2 h in accordance with accepted standard [4(7)]. accepted standard [4(8)] }.
All openings in the floors shall be protected by vertical
3.4.10 Electrical Installations
enclosures extending above and below such openings,
the walls of such enclosures having a fire resistance of For requirements regarding electrical installations from
not less than 2 h and all openings therein being the point of view of fire safety, reference maybe made

PART 4 FIRE AND LIFE SAFETY 23


to good practice [4(9)] (see also Part 8 ‘Building 3.4.12.3 Where smoke venting facilities are installed
Services, Section 2 Electrical and Allied Installations’). for purposes of exit safety, these shall be adequate to
prevent dangerous accumulation of smoke during the
3.4.11 Air-conditioning and Ventilation
period of time necessary to evacuate the area served,
Air-conditioning and ventilation requirements of using available exit facilities with a margin of safety to
different rooms or areas in any occupancy shall be as allow for unforeseen contingencies. It is recommended
given in Part 8 ‘Building Services, Section 1 Lighting that smoke exhaust equipment should have a minimum
and Ventilation and Section 3 Air-conditioning, capacity of 12 air changes per hour. Where mechanical
Heating and Mechanical Ventilation’. venting is employed, it shall be firesafe.

3.4.11.1 Air-conditioning and ventilating systems 3.4.12.4 The discharge apertures of all natural draft
shall be so installed and maintained as to minimize the smoke vents shall be so arranged as to be readily
danger of spread of fire, smoke or fumes from one accessible for opening by fire service personnel.
floor to other or from outside to any occupied building
3.4.12.5 Power operated smoke exhausting systems
or structure (see C-1.17).
shall be substituted for natural draft. vents only by
3.4.11.2 Air-conditioning and ventilating systems specific permission of the Authority.
circulating air to more than one floor or f~e area shall be
3.4.13 Heating
provided with dampers designed to close automatically
in case of fke and thereby preventing spread of fue or Installation of chimney and heating apparatus shall be
smoke and shall be in accordance with the accepted in accordance with good practice [4(13)].
standard [4( 10) ]. Such a system shall also be provided
3.4.14 Additional Precautions
with automatic controls to stop fans in case of fwe, unless
arranged to remove smoke from a fue, in which case these In addition to the factors covered by 3.4.2 to 3.4.12
shall be designed to remain in operation. there are certain aspects, applicable to particular
occupancies only, which may effect the spread of
3.4.11.3 Air-conditioning system serving large places
fumes and thus the safe evacuation of the building in
of assembly (over 1000 persons), large departmental
case of fue. Some such aspects are:
stores or hotels with over 100 rooms in a single block
shall be provided with effective means for preventing a) interior finish and decoration;
circulation of smoke through the system in the case of b) seating, aisles, railings, turnstiles and
a fire in air filters or from other sources drawn into the revolving doors in places of assembly;
system, and shall have smoke sensitive devices for c) service equipment and storage facilities in
actuation in accordance with the accepted standards buildlngs other than storage buildings; and
[4(11)].
d) hazards on stage, in waiting spaces, projection
3.4.11.4 From fire safety point of view, separate air booths, etc, in theatres and cinemas.
handling units for the various floors shall be provided
3.4.15 Su$ace Interior Finishes
so as to avoid the hazards arising from spread of fire
and smoke through the air-conditioning ducts. The 3.4.15.1 The use of combustible surface finishes on
requirements of air-conditioning ducts shall be in walls (including facade of the building) and ceilings
accordance with good practice [4( 12)]. affects the safety of the occupants of a building. Such
finishes tend to spread the fiie and even though the
3.4.11.5 For normal operation, air changes schedule
structural elements may be, ,adequately fme resistant,
shall be as given in Part 8 ‘Building Services, Section 3
serious danger to life may result. It is, therefore,
Air-condhioning, Heating and Mechanical Ventilation’.
essential to have adequate p~ecautions to minimize
3.4.12 Smoke Venting spread of flame on wall, facade of building and ceiling
surfaces.
3.4.12.1 Smoke venting facilities for safe use of exits
in windowless buildings, underground structures, large The finishing materials used for various surfaces and
area factories, hotels and assembly buildlngs (includlng d6cor shall be such that it shall not generate toxic
cinema halls) shall be automatic in action with manual smoke/fumes.
controls in addition. 3.4.15.2 The susceptibility to fire of various types
3.4.12.2 Natural draft smoke venting shall utilize roof of wall surfaces is determined in terms of the rate of
vents or vents in walls at or near the ceiling level; such spread of flame. Based on the rate of spread of flame,
vents shall be normally open, or, if closed, shall be surfacing material shall be considered as divided into
designed for automatic opening in case of fire, by four classes as follows {see also good practice
release of smoke sensitive devices. [4(14)]}.

24 NATIONAL BUILDING CODE OF INDIA


-’T--

Class 1 Surfaces of very low flame spread. a) Wired glass — The wired glass shall be of
Class 2 Surfaces of low flame spread. minimum half hour fire resistance rating.
Class 3 Surfaces of medium flame spread. b) Sashes and frames — The sashes or frames
Class 4 Surfaces of rapid flame spread. or both shall be entirely of iron or other
suitable metal such as stainless steel, securely
3.4.15.3 The uses for which surface materials falling bolted or keyed into the wall, except in the
into various classes shall be adopted in building case of panels in internal doors.
construction are given below:
c) Setting of glass — The panels of glass shall
be set in rebates or grooves not less than
Class 1 Class 2 Class 3
6.0 mm in width or depth, with due allowance
May be May be used in May be used only for expansion, and shall be secured by hard
used in any any situation, in living rooms and metal fastenings to the sashes or frames
situation except on walls, bed rooms (but not independently of any cement or putty used
facade of the in rooms on the for weather-proofing purposes.
building, roof) and only as a
staircase and lining to solid walls 3.4.16.3 Electro-copper glazing shall comply with the
corridors and partitions; not following requirements:
on staircases or
a) Electro-copper glazing — The electro-copper
corridors or facade
glazing shall be of minimum half hour fire
of the building.
resistance rating.
NOTE — Panelling (lining) shall be permitted in a limited b) Sashes and frames — The sashes or frames
area.It shallnot be permittedin a vestibule.
or both shall be entirely of iron or other hard
3.4.15.4 Materials of Class 4 which include untreated metal, securely bolted or keyed into the wall,
wood fibreboards may be used with due fire retardant except when in panels in internal doors.
treatment as ceiling lining, provided the ceiling is at c) Fixing of sectional lights — The sectional
least, 2.4 m from the top surface of the floor below, lights shall be set in rebate or grooves not less
and the wall surfaces conform to requirements of class than 6.5 mm in width or depth, with due
[see Note under 3.4.15.3] Class 4 materials shall not allowance for expansion and shall be secured
be used in kitchens, corridors and staircases. Some by hard metal fastenings to the sashes or
materials contain bitumen and, in addition to risk from frames independently of any lead, cement or
spread of fire, emit dense smoke on burning; such putty used for weather-proofing purposes.
materials shall be excluded from use under these
3.4.16.4 Maximum permissible area shall be 5 m2 for
conditions and shall also not be used for construction
protection by wired glass or electro-copper glazing.
of ceiling where the plenum is used for return air in
air-conditioned buildings [see also 5.1.7(m)]. 3.4.16.5 Casement

3.4.15.5 When frames, walls, partitions or floors are Hard metal casements, not exceeding 0.8 m2 fitted with
lined with combustible materials, the surfaces on both wired glass or electro-copper glazing in accordance
sides of the materials shall conform to the appropriate with 3.4.16.2 and 3.4.16.3, secured to the frames by
class, because there is considerable danger from fire hard metal hinges not more than 600 mm apart and by
starting and rapidly spreading within the concealed fastening at top, centre and bottom shall be permissible.
cavity unknown to the occupants whose escape may
3.4.17 Skylights
be hampered there by. For detailed information on
materials and details of construction with their fire- 3.4.17.1 Wired glass for skylights or monitor lights
resistance rating, reference may be made to good shall comply with the following requirements:
practice [4(15)].
a) Wired glass for skylights or monitor lights —
3.4.16 Glazing The wired glass for skylights or monitor lights
shall be of minimum half hour fire resistance
3.4.16.1 Building of Types 1 to 4 construction shall rating.
employ one of the two types of glazing described
b) Frames and glazing — The frame shall be
in 3.4.16.2 and 3.4.16.3 except that Type 4 construction
continuous and divided by bars spaced at not
may have the alternative of hardwood sashes or frames
more than 700 mm centres. The frame and
or both.
bars shall be of iron or other hard metal, and
3.4.16.2 Wired glass shall comply with the following supported on a curb either of metal or of wood
requirements: covered with sheet metal. The toughened glass

PART 4 FIRE ANDLIFE SAFETY 25


T-

shall be secured by hard metal fastenings to 4.2.8 The floors of areas covered for the means of exit
the frame and bars independently of any lead, shall be illuminated to values not less than 1 ft candle
cement or putty used for weather-proofing (10 lUX)at floor level. In auditoriums, tbeatres, concert
purposes. halls and such other places of assembly, the
illumination of floor exit/access maybe reduced during
3.4.18 Louvers
period of performances to values not less than 1/5 ft
Louvers wherever provided shall be of minimum half candle (2 lux).
hour fire resistance rating.
4.2.9 Fire doors with 2 h fire resistance shall be
3.4.19 Glass of facade for high rise buildings, etc shall provided at appropriate places along the escape route
be of minimum 1 h fire resistance rating. and particularly at the entrance to lift lobby and stair
well where a ‘funnel or flue effect’ may be created,
4 LIFE SAFETY inducing an upward spread of fire to prevent spread of
4.1 General fire and smoke.

Every building shall be so constructed, equipped, 4.2.10 All exits shall provide continuous means of
maintained and operated as to avoid undue danger to egress to the exterior of a building or to an exterior
the life and safety of the occupants from fire, smoke, open space leading to a street.
fumes or panic during the time period necessary for 4.2.11 Exits shall be so arranged that they may be
escape. reached without passing through another occupied
unit.
4.2 General Exit Requirements
4.3 Occupant Load
4.2.1 Artexit may be a doorway; corndo~ passageway(s)
to an internal staircase, or external staircase, or to a For determining the exits required, the number of
VERANDAH or terrace(s), which have access to the persons within any floor area or the occupant load shall
street, or to the roof of a building or a refuge area. An be based on the actual number of occupants, but in no
exit may also include a horizontal exit leading to an case less than that specified in Table 20.
adjoining building at the same level.
4.3.1 Mezzanine
4.2.2 Lifts and escalators shall not be considered as
The occupant load of a mezzanine floor discharging
exits.
to a floor below shall be added to that floor occupancy
4.2.3 Every exit, exit access or exit discharge shall be and the capacity of the exits shall be designed for the
continuously maintained free of all obstructions or total occupancy load thus established.
impediments to full use in the case of fire or other
emergency. 4.4 Capacities of Exits

4.2.4 Every building meant for human occupancy shall 4.4.1 The unit of exit width, used to measure the
be provided with exits sufficient to permit safe escape capacity of any exit, shall be 500 mm. A clear width
of occupants, in case of fire or other emergency. of 250 mm shall be counted as an additional half unit.
Clear widths less than 250 mm shall not be counted
4.2.5 In every building or structure, exits shall comply for exit width.
with the minimum requirements of this part, except
NOTE — The total occupants from a particular floor must
those not accessible for general public use.
evacuate within 2% minutes for Type 1 construction,
IY2 minutes for Type 2 constructionand 1 minute for Type 3
4.2.6 No building shall be so altered as to reduce the
construction.Size of the exit doorfexitwayshrdlbe calculated
number, width or protection of exits to less than that accordingly keeping in view the travel distance as per
required. Table 22. “

4.2.7 Exits shall be clearly visible and the route to 4.4.2 Occupants per unit exit width shall be in
reach the exits shall be clearly marked and signs posted accordance with Table 21.
to guide the occupants of the floor concerned. Signs
4.4.3 Horizontal Exit Allowance
shall be illuminated and wired to an independent
electrical circuit on an alternative source of supply. When horizontal exit is provided in buildings of
The sizes and colours of the exit signs shall be in mercantile, storage, industrial, business and assembly
accordance with good practice [4( 16)]. The colour of occupancies, the capacity per storey per unit width of
the exit signs shall be green. exit of stairways in Table 21 may be increased by 50
NOTE — This provision shall not apply to A-2 and A-4 percent and in buildings of institutional occupancy it
occupanciesless than 15 m in height. may be increased by 100 percent.

26 NATIONALBUILDINGCODE OF INDIA
“r--

Table 20 Occupant Load in Table 22, except in assembly and institutional


(Clause 4.3) occupancies in which case it shall not exceed 6 m.

4.5.3 Whenever more than one exit is required for any


S1 Group of Occupancy Occupant Load, Ftoor
No. Area in m2/Person room space or floor of a building, exits shall be placed
(1) (2) (3) as remote from each other as possible and shall be
arranged to provide direct access in separate directions
i) Residential(A) 12.5
from any point in the area served.
ii) Educational(B) 4
iii) Institutional(C) 15 (seeNote 1) Table 22 Travel Distance for Occupancy and
iv) Assembly(D) Type of Construction
a) With fixedor Iooseseats 0.6 (seeNote 2)
and dancefloors (Clauses 4.4.1,4.5.1 and 4.5.2)
b) Withoutseatingfacilities 1.5(see Note 2) S1 Group of Occupancy Maximum Travel Distance
includlngdiningrooms No. Construction
v) Mercantile(F) / Y
a) Streetfloor and sales 3 Types 1 & 2 Types 3 & 4
basement m m
b) Uppersale floors 6 (1) (2) (3) (4)
vi) Businessand industrial(E&G) 10 i) Residential(A) 30.0 22.5
vii) Storage(H) 30 ii) Educational(B) 30.0 22.5
viii) Hazardous(J) 10 iii) Jtrstitutionrd(C) 30.0 22.5
iv) Assembly(D) 30.0 30.0
NOTES
v) Bnsiness(E) 30.0 30.0
1 Occupant load in dormitory portions of homes for the
aged, orphanages, insane asylums, etc, where sleeping vi) Menmntile~ 30.0 30.0
vii) Industrial(G) 45.0 0
accommodationis provided,shallbe calculatedat not less than
7.5 m2gross floor aretiperson. viii) Storage(H) 30.0 1)
ix) Hazardous(J) 22.5 0
2 The gross floor area shall include, in addition to the main
assembly room or space, any occupied connecting room or
spacein the samestoreyor in the storeysaboveor below,where NOTES
entrance is common to such rooms and spaces and they are 1 For fully sprittkleredbuilding, the travel distance may be
availablefor use by the occupantsof the assemblyplace. No increasedby 50 percent of the values specified.
deductionsshallbe madein the grossareafor corridors,closets 2 Ramps shall be protected with automatic sprinkter system
or other sub-d]visions;the area shaUinclude all space serving and shall be countedas one of the means of escape.
the particular assembIyoccupancy. 11Constructionof type 3 or 4 is trotprttdtted.

Table 21 Occupants per Unit Exit Width 4.6 Number of Exits


(Clauses 4.4.2,4.4.3 and C-1.6.2) 4.6.1 General

S1 Group of Number of Occupants The general requirements of number of exits shall


No. Occupancy ~ supplement the requirement of different occupancies
in 6.1 to 6.9.
(1) (2) (3) (4) (5)
4.6.2 All buildings, which are 15 m in height or above,
i) Residential(A) 25 50 75
and all buildings used as educational, assembly,
ii) Educational(B) 25 50 75
institutional, industrial, storage, and hazardous
iii) Institntiomd(C) 25 50 75
iv) Assembly(D) 40 50 60 occupancies and mixed occupancies with any of the
v) Business(E) 50 60 75 aforesaid occupancies, having area more than 500 m2
vi) Mercantile(F) 50 60 75 on each floor shall have a finimum of two staircases.
vii) Indnstrkd(G) 50 60 75 They shall be of enclosed type; at least one of them
viii) Storage(H) 50 60 75 shall be on external walls of buildings and shall open
ix) Hazardous(J) 25 30 40 directly to the exterior, interior open space or to an
open place of safety. Further, the provision or otherwise
4.5 Arrangement of Exits of alternative staircases shall be subject to the
requirements of travel distance being complied with.
4.5.1 Exits shall be so located that the travel, distance
on the floor shall not exceed the distance given in 4.7 Doorways
Table 22.
4.7.1 Every exit doorway shall open into an enclosed
4.5.2 The travel distance to an exit from the dead end stairway or a horizontal exit of a corridor or passageway
of a corridor shall not exceed half the distance specified providing continuous and protected means of egress.

PART 4 FIRE ANDLIFE SAFETY 27


4.7.2 No exit doorway shall be less than 1000 mm in a) Residential buildlngs (dwellings) l.Om
width except assembly buildings where door width b) Residential hotel buildings 1.5 m
shall be not less than 2000 mm. Doorways shall be c) Assembly buildlngs like auditorium, 2.0 m
not less than 2000 mm in height. theatres and cinemas
i
4.7.3 Exit doorways shall open outwards, that is, away d) Educational buildings up to 30 m in 1.51n
from the room, but shall not obstruct the travel along height
any exit. No door, when opened, shall reduce the e) Institutional buildings like hospitals 2.0 m
required width of stairway or landing to less than All other buildings 1.5 m
f)
900 mm; overhead or sliding doors shall not be
installed. 4.9.7 The minimum width of tread without nosing
shall be 250 mm for internal staircase of residential
NOTE — In the case of buildings where there is a central
corridor, the doors of rooms shall open inwards to permit buildings. This shall be 300 mm for assembly, hotels, t
smooth flow of traffic in the corridor. educational, institutional, business and other buildings.
The treads shall be constructed and maintained in a
4.7.4 Exit door shall not open immediately upon a
manner to prevent slipping.
flight of stairs; a landing equal to at least the width of
the door shall be provided in the stairway at each 4.9.8 The maximum height of riser shall be 190 mm
doorway; the level of landing shall be the same as that for residential buildings and 150 mm for other buildings
of the floor which it serves. and the number shall be limited to 15 per flight.

4.7.5 Exit doorways shall be openable from the side 4.9.9 Handrails shall be provided at a height of
1000 mm to be measured from the base of the middle
which they serve without the use of a key. F-
of the treads to the top of the handrails. Balusters/railing
4.7.6 Mirrors shall not be placed in exit ways or exit shall be provided such that the width of staircase does
doors to avoid confusion regarding the direction of exit. not reduce (see Fig. 1).

4.8 Corridors and Passageways 4.9.10 The number of people in between floor landings
in staircase shall not be less than the population on
4.8.1 Exit corridors and passageways shall be of width
each floor for the purpose of design of staircase. The
not less than the aggregate required width of exit
design of staircase shall also take into account the
doorways leading from them in the direction of travel
following:
to the exterior.
a) The minimum headroom in a passage under
4.8.2 Where stairways discharge through corridors and the landing of a staircase and under the
passageways, the height of corridors and passageways staircase shall be 2.2 m.
shall be not less than 2.4 m.
b) For building 15 m in height or more, access
4.8.3 All means of exit including staircases lifts lobbies to main staircase shall be through afire/smoke
and corridors shall be adequately ventilated. check door of a minimum 2 h fire resistance
rating. Fire resistance rating may be reduced
4.9 Internal Staircases to 1 h for residential buildings (except hotels
and starred hotels).
4.9.1 Internal stairs shall be constructed of non-
combustible materials throughout. c) No living space, store or other fire risk shall
open directly iqto the staircase or staircases.
4.9.2 Internal stairs shall be constructed as a self-
d) External exit door of staircase enclosure at
contained unit with an external wall of the building
ground level shall open directly to the open
constituting at least one of its sides and shall be
spaces or throug~ a large lobby, if necessary.
completely enclosed.
e) The main and external staircases shall be
4.9.3 A staircase shall not be arranged round a lift shaft. continuous from ground floor to the terrace
level.
4.9.4 Hollow combustible construction shall not be
permitted. f) No electrical shafts/AC ducts or gas pipes, etc,
shall pass through or open in the staircases.
4.9.5 No gas piping or electrical panels shall be Lifts shall not open in staircase.
allowed in the stairway. Ducting in stairway may be
g) No combustible material shall be used for
permitted if it is of 1 h fire resistance rating.
decoration/wall paneling in the staircase.
4.9.6 Notwithstanding the detailed provision for exits h) Beams/columns and other buildlng features
in accordance with 4.3, 4.4 and 4.5, the following shall not reduce the head room/width of the
minimum width shall be provided for staircases: staircase.

28 NATIONALBUILDINGCODE OF INDIA
5LU3 I tK

All dimensions in millimetres.

FIG. 1 TYPICALDETAILFORHANDRAIL/BL~JSTERS
OF A STAIRCASE

j,
The exit sign with arrow indicating the way 4.10 Pressurization of Staircases (Protected Escape
to the escape route shall be provided at a Routes)
suitable height from the floor level on the wall
4.10.1 Though in normal building design,
and shall be illuminated by electric light
compartmentation plays a vital part in limiting the
connected to corridor circuits. All exit way spread of fire, smoke will readily spread to adjacent
marking signs should be flush with the wall spaces through the various leakage openings in the
and so designed that no mechanical damage compartment enclosure, such as cracks, openings
shall occur to them due to moving of furniture around pipes ducts, airflow grills and doors, as perfect
or other heavy equipments. Further, all sealing of all these openings is not possible. It is smoke
landings of floor shall have floor indicating and toxic gases, rather than flame, that will initially
boards prominently indicating the number of obstruct the free movement of occupants of the
floor as per bye-laws. building through the means of escape (escape routes).
The floor indication board shall be placed on Hence the exclusion of smoke and toxic gases from
the wall immediately facing the flight of stairs the protected routes is of great importance.
and nearest to the landing. It shall be of size 4.10.2 Pressurization is a method adopted for protected
not less than 0.5 m x 0.5 m. escape routes against ingress of smoke, especially in
k) Individual floors shall be prominently high-rise buildings. In pressurization, air is injected
indicated on the wall facing the staircases. into the staircases, lobbies or corridors, to raise their
m) In case of single staircase it shall terminate pressure slightly above the pressure in adjacent parts
at the ground floor level and the access to of the building. As a result, ingress of smoke or toxic
the basement shall be by a separate staircase. gases into the escape routes will be prevented. The
The second staircase may lead to basement pressurization of staircases shall be adopted for high
levels provided the same is separate at rise buildings and building having mixed occupancy/
ground level by ventilated lobby with multiplexes having covered area more than 500 m2.
discharge points to two different ends 4.10.3 The pressure difference for staircases shall be
through enclosures. as under:

~M?Z 4 NRE ~ND LIFE SAFETY 29


be resorted to. The use of pressurized and naturally
Building Pressure Di#erence
ventilated staircases in the same building may introduce
Height ~
Reduced Emergency difficulties and hence shall be avoided. Under no
Operation Operation circumstances shall a pressurized staircase be
(Stage 1 of (Stage 2 of a connected by a corridor or lobby to an un-pressurized
a 2-Stage 2-Stage System staircase. Wherever pressurized staircase is to be
System) or Single connected to un-pressurized area, the two areas shall
Stage System) be segregated. r
(Pa) (Pa)
Less than 15 m 8 50 4.11 External Stairs

15 m or above 15 50 An external staircase is desirable to be provided for


high rise buildings.
If possible, the same levels shall be used for lobbies
and corridors, but levels slightly lower may be used External stairs, when provided shall comply the
for these spaces if desired. The difference in following:
pressurization levels between staircase and lobbies (or 4.11.1 External stairs shall always be kept in sound
corridors) shall not be greater than 5 Pa. operable conditions.
4.10.4 Pressurization system may be of two types: 4.11.2 Ail external stairs shall be directly connected
a) Single-stage, designed for operation only in to the ground.
the event of an emergency, and 4.11.3 Entrance to the external stairs shall be separate
b) Two-stage, where normally a level of and remote from the internal staircase.
pressurization is maintained in the protected
4.11.4 Care shall be taken to ensure that no wall
escape routes and an increased level of
opening or window opens onto or close to an external
pressurization can be brought into operation
stairs.
in an emergency.
4.10.5 The normal air-conditioning system and the 4.11.5 The route to the external stairs shall be free of
pressurization system shall be treated as an integral obstructions at all times.
one, especially for a two-stage system. When the 4.11.6 The external stairs shall be constructed of non-
emergency pressurization is brought into action, the combustible materials, and any doorway leading to it
following changes in the normal air-conditioning shall have the required fire resistance.
system shall be effected:
4.11.7 No external staircase, used as a f~e escape, shall
a) Any re-circulation of air shall be stopped and be inclined at an angle greater than 45° from the
all exhaust air vented to atmosphere; horizontal.
b) Any air supply to the spaces/areas other than
4.11.8 External stairs shall have straight flight not less
escape routes shall be stopped;
than 1250 mm wide with 250 mm treads and risers
c) The exhaust system may be continued
not more than 190 mm. The number of risers shall be
provided:
limited to 15 per flight.
1) the positions of the extraction grills
permit a general air flow away from the 4.11.9 Handrails shall be of a height not less than
protected escape route entry; 1000 mm and not ex&eding 1200 mm. There shall
be provisions of balusters with maximum gap of
2) the construction of the ductwork and fans
150 mm.
is such that, it will not be rendered
inoperable by hot gases and smoke; and 4.11.10 The use of spiral staircase shall be limited to
3) there is no danger of spread of smoke to low occupant load and to a building not exceeding 9 m
other floors by the path of the extraction in height.
system which can be ensured by keeping
A spiral stair case shall be not less than 1500 mm in
the extraction fans running.
diameter and shall be designed to give adequate
4.10.6 The pressurization system can be headroom.
interconnected with the automatic/manual fire alarm
4.11.11 Unprotected steel frame staircase will not be
system for actuation.
accepted as means of escape. However, steel staircase
4.10.7 It will be desirable to have all the staircases in in an enclosed fue rated compartment of 2 h will be
a building pressurized, if pressurization system is to accepted as means of escape.

30 NATIONALBUILDINGCODE OF INDIA
4.12 Horizontal Exits capacity and limiting dimensions except where
specified in 6.1 to 6.9 for special uses and occupancies.
4.12.1 The width of horizontal exit shall be same as
for the exit doorways. 4.14.2 The slope of a ramp shall not exceed 1 in 10.
In certain cases steeper slopes maybe permitted but in
4.12.2 A horizontal exit shall be equipped with at least
no case greater than 1 in 8.
one fire/smoke door of minimum 1 h fire resistance,
of self-closing type. Further, it is required to have direct 4.14.3 For all slopes exceeding 1 in 10 and wherever
connectivity to the fire escape staircase for evacuation. the use is such as to involve danger of slipping, the
ramp shall be surfaced with approved non-slipping
4.12.3 For buildings more than 24 m in height, refuge
material.
area of 15 m2 or an area equivalent to 0.3 m2 per person
to accommodate the occupants of two consecutive 4.15 Fire Lifts
floors, whichever is higher, shall be provided as under:
4.15.1 Where applicable, fire lifts shall be provided
The refuge area shall be provided on the periphery of with a minimum capacity for 8 passengers and fully
the floor or preferably on a cantilever projection and automated with emergency switch on ground level. In
open to air at least on one side protected with suitable general, buildings 15 m in height or above shall be
railings. provided with fire lifts.
a) For floors above 24 m and Up to 39 m — 4.15.2 In case of f~, only fireman shall operate the fwe
One refuge area on the floor immediately lift. In normal course, it may be used by other persons.
above 24 m.
4.15.3 Each fire lift shall be equipped with suitable .
b) Forjloors above 39 m — One refuge area on
inter-communication equipment for communicating
the floor immediately above 39 m and so on
with the control room on the’ ground floor of the
after every 15 m. Refuge area provided in
building.
excess of the requirements shall be counted
towards FAR. 4.15.4 The number and location of fire lifts in a
NOTE— Residentialflatsin multi-storiedbuildingwith building shall be decided after taking into consideration
balcony, need not be provided with refuge area, various factors like building population, floor area,
howeverflats withoutbalconyshallproviderefugearea comprtrtmentation, etc.
as given above.
4.12.4 Where there is a difference in level between 4.16 Emergency and Escape Lighting
connected areas for horizontal exits, ramps, not more 4.16.1 Emergency lighting shall be powered from a
than 1 in 10 m slope shall be provided; steps shall not source independent of that supplying the normal
be used. lighting [see good practice [4(17)].
4.12.5 Doors in horizontal exits shall be openable at Escape lighting shall be capable of
all times from both sides.
a) Indicating clearly and unambiguously the
4.13 Fke Tower escape routes,
b) Providing adequate illumination along such
Fire towers are the preferred type of escape route for
routes to allow safe movement of persons
storeyed buildings and these shall be considered as the
towards and throuph the exits,
safest route for escape. Their number, location and size
shall depend on the building concerned, and its c) Ensuring that fire alarm call points and fire-
associated escape routes. fighting equipments provided along the
escape routes can be readily located.
4.13.1 In high rise buildings with over 8 storeys or
24 m in height, at least one required means of egress 4.16.2 The horizontal luminance at floor level on the
shall preferably be a fire tower. centreline of an escape route shall be not less than
10 lUX. In addition, for escape routes up to 2 m wide,
4.13.2 The fire towers shall be constructed of walls 50 percent of the route width shall be lit to a minimum
with a 2 h fire resistance rating without openings other of 5 lUX.
than the exit doorways, with platforms, landings and
balconies having the same fire-resistance rating. 4.16.3 The emergency lighting shall be provided to
be put on within 1 s of the failure of the normal lighting
4.14 Ramps supply.
4.14.1 Ramps shall comply with all the applicable 4.16.4 Escape lighting luminaries should be sited to
requirements for stairways regarding enclosure, cover the following locations:

PART 4 FIRE ANDLIFE SAFETY 31


a) Near each intersection of corridors, b) Staircase and corridor lighting shall also
b) at each exit door, be connected to alternative supply. The
Near each change of direction in the escape alternative source of supply maybe provided
c)
route, by battery continuously trickle charged from
the electric mains; and
d) Near each staircase so that each flight of stairs
receives direct light, c) Suitable arrangements shall be made by
installing double throw switches to ensure that
e) Near any other change of floor level,
the lighting installed in the staircase and the
f) Outside each final exit and close to it, corridor does not get connected to two sources
g) Near each fire alarm call point, of supply simultaneously. Double throw
h) Near fire-fighting equipment, and switch shall be installed in the service room
j) To illuminate exit and safety signs as required for terminating the stand-by supply.
by the enforcing authority.
4.18 Fire Detection and Warning
NOTE — For the purposes of this clause ‘near’ is
normally considered to be within 2 m measured In buildings of such size, arrangement or occupancy
horizontally. where a fwe may not itself provide adequate warning
4.16.5 Emergency lighting systems shall be designed to occupants, automatic fire detection and alarm
to ensure that a fault or failure in any one luminaire facilities shall be provided, where necesstiry, to warn
does not further reduce the effectiveness of the occupants early of the existence of fwe, so that they
system. may escape, and to facilitate the orderly conduct of
fue exit drills. ,-
4.16.6 The luminaries shall be mounted as low as
possible, but at least 2 m above the floor level. 4.18.1 The fire detection system shall be in accordance
with accepted standards [4( 18)]. Guidelines for
4.16.7 Signs are required at all exits, emergency
selection of various types of f~e detectors for different
exits and escape routes, which should comply with
occupancies and their installation and maintenance
the graphic requirements of the relevant Indian
shall be in accordance with [4(19)].
Standards.
4.18.2 The requirements of fire detection and alarm
4.16.8 Emergency lighting lurninaires and their fittings
systems are covered for each occupancy in Table 23
shall be of non-flammable type.
and under 6.1 to 6.9; attention is also drawn to such
4.16.9 It is essential that the wiring and installation of requirements in case of high rise buildings (15 m or
the emergency lighting systems are of high quality so more in height) as given in Annex C.
as to ensure their perfect serviceability at all times.
5 FIRE PROTECTION
4.16.10 The emergency lighting system shall be
capable of continuous operation for a minimum 5.1 Fire Extinguishers/Fixed Fire Fighting
duration of 1 h and 30 m even for the smallest Installations
premises. 5.1.1 All buildings depending upon the occupancy use
4.16.11 The emergency lighting system shall be well and height shall be protected by fue extinguishers, wet
maintained by periodical inspections and tests so as to riser, down-comer, automatic sprinkler installation,
ensure their perfect serviceability at all times. high/medium velocity water spray, foam, gaseous or
dry powder system in accordance with the provisions
4.17 Illumination of Means of Exit
of 5.1.2 to 5.1.9.
Staircase and corridor lights shall conform to the
5.1.2 These fm extinguishers/fixed installations shall
following:
be in accordance with accepted standards [4(20)]. The
a) The staircase and corridor lighting shall be typical requirements of fire extinguishers/wet riser/
on separate circuits and shall be independently down-comer installation and capacity of water storage
connected so that it could be operated by one tanks and fire pumps, etc shall be as specified in
switch installation on the ground floor easily Table 23. The requirements regarding size of mains/
accessible to fire fighting staff at any time risers shall be as given in Table 24. The typical
irrespective of the position of the individual arrangements of down-comer and wet riser installations
control of the light points, if any. It should be are shown in Fig. 2 and Fig. 3. The wet riser shall be
of miniature circuit breaker type of switch so designed for zonal distribution ensuring that unduly
as to avoid replacement of fuse in case of high pressures are not developed in risers and hose-
crisis; pipes.

32 NATIONAL BUILDING CODE OF INDIA


I I H

HOSE REEL

SINGLE HEAD
HP - HYDRANT PUMP/ LANDING VALVE
MAIN ELECTRIC PUMP AIR RELEASE VALVE
!JP - JOCKEY PUMP t
DP - DIESEL PUMP SLUICE VALVE
SP - SPRINKLER PUMP
SPRINKLER LINE TEST DRAIN d L WET RlsER + NON - RETURN VALVE
SH - SUCTION HEADER
DH - DLIVERYHEADER -—.—.
-—-—- —-—e—
—- —-— -—-
-—. — FLOW SWITCH
R - PIPE TO RISER
SPRINKLER HEAD
Y - PIPE TO YARD
HYDRANT CABLE TO ANNUNCIATION
s - PIPE TO SPRINKLER PANEL
SYSTEM E====:===:===:=== t=: —- CABLE CONDUITE FOR
t
AV - AIR VESSEL
IIr ‘~ 9 HOOTER

-—-—-—
-—. —-—
.—
--—-—
-— ——-—
-
-—-
ICV - INSTALLATION — CABLE CONDUIT FOR
CONTROL VALVE l!!!! b! MANUAL CALL BOX
*
EJQ
.. == + HOOTER

7“A
t

P 7 +3 MANUAL CALL BOX

~ FIRE BRIGADE DRAW


*
.—-—.
—-—-—-
—-—
-—-—.
—- & FROM TANK
●

-—-—-
—-—-—
-—-
—.
—-—
-— ~ FIRE BRIGADE INLET

[[’66
p: Jlllll
m Ian \t!!!!:! TANK FILLING

. ;60000
FIRST FLOOR
-—-—-
-—-—- —-— .— -—-
—- —-— -— —- —-— -—-
-—-— -

F“””””””
YARD b II I iiii i!iiiiiiii FIRE ALARM PANEL WITH
n 1

I
HYDRANT I A

—-—.
●

—
-—-—-
-—-—-
.—
—4
GROUND r~’Lvwm
-
—-
—.—
~fin
—-— -~
.—. —- -
b
~:::

1111
T
BATTERY BACK-UP AND
P.A. SYSTEM
4
-I
A L rax
IIo 66(

L UG FIRE
TANK

FIG. 3 TYPICAL ARRANGEMENrr


OF WET RISERAND TOTAL SPRINKLERSYSTEMOFBUILDING
OTHERTHAN APPARTMENTEXCEEDING30 m IN HEIGHT

NATIONAL BUILDING CODE OF INDIA


Tabk 23 Minimum Requirements for Fire Fighting Installations
(Clauses 4.18.2,6.1.2,6.2.3,6.3.2, 6.4.3,6.5.2,6.5.2.1, 6.5.2.2,6.5.2.3,6.5.2.4, 6.5.2.5,6.6.2,6.7.2, 6.8.2 and 6.9.2)

,
S1 Type of Building Type of Installation Water Supply Pump Capacity
No. Occupancy (in 1) (in I/tin)

Fire Hose Dry Wet Down- Yard Automatic Manually Automatic Underground Terrace pump Near At the
Extin- Reel Riser Riser Comer Hydrant Sprinkler Operated Detection Static Water Underground Terrace
Tank
gusher System Electric and Alarm Storage Static Water Tank Level
(see
Fire Alarm System Tank Storage Tank with
Note 6)
Systems (Fire Pump) Minimum
with Minimum Pressure
Pressure of of
3.5 kglcm2 2.0 kg/cm2
at
Terrace Level

(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15)

RESIDENTIAL BUILDINGS (A)

a) Lodging or Rooming
Houses (A-1)
(see Note 1)

1) Less than 15 min


height

i) Up to 15 rooms R NR NR NR NR NR R NR NR NR 5000 NR NR
(see Note 2) (see Note 3)

ii) More than 15 and R R NR NR NR NR R NR NR NR 5000 NR 450


up to 30 rooms (see Note 2) (5 000) (450)
(see Note 4) (see Note 4)

iii) More than R R NR NR NR NR R R NR NR 10000 NR 450


30 rooms (see Note 2) (see Note 5) (5 000) (450)
(see Note 4) (see Note 4)

b) One or two Family NR NR NR NR NR NR NR NR NR NR NR ‘ NR NR


Prkate Dwellings
(A-2)
(see Note 1)

w
W

*
r~
Table 23 — Contintied

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (H) (12) (13) (14) (15)

C) Dormitories(A-3)
Apartment
Houses (A-4)

1) Less than 15 m R R NR NR NR NR R NR NR NR 5000 NR 450


in height (see Note 2) (5 000) (450)
(see Note 4) (see Note 4)

2) 15 m and above but R R NR NR R NR R R NR NR 25000 NR 900


not exceeding 35 m (see Note 2) (see Note 7)
in height

3) Above 35 m but not R R NR R NR NR R R NR 75000 5000 (see Note 19) NR


exceeding 45 min (see Notes (5 000)
height 2 and 8) (see Note 4)

4) Above 45 m in height R R NR R NR R R R NR 75000 10000 (see Note 20) NR


but not exceeding
60 m in height

5) Above 60 m R R NR R NR R R R R 100000 25000 (see Note 21) NR


in height

d) Hotek (A-5)

1) Less than 15m


in height

i) Covered area not R R NR NR NR NR R R NR NR 5000 NR 450


exceeding 300 m2 (see Note 2) (see Note 2) (see Note 3)
on eaeh floor

ii) Covered area R R NR R NR NR R R R 10000 for 10000 (see Notes 5 NR


exceeding 300 m2 (see (see Note 2) every 500 m2 (see Note 2) and 19)
but not more Note 5) covered area
1000 m2 on subject to
each floor minimum of
50000
(see Note 5)

iii) Covered area R R NR R NR R R R R 100000 10000 (see Notes 9 NR


exceeding (see (see Note 10) (see Note 9) (see Note 2) and 19)
1000 m2 on Note 9)
each floor
Y Table 23 — Continued”
w
+—
a (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15)
m
4
2) 15mand above but R R NR R NR R R R R 150000 20000 (see Note 20) NR
E not exceeding 30 m (see Note 10)
*
z
u 3) Above 30min R R NR R NR R R R R 200000 20000 (see Note 21) NR
r height (see Note 10)
9
m
e) Hotels (A-6) R R NR R NR R R R R 200000 20000 (see Note 22) NR
g
(see Note 10)
M EDUCATIONAL BUILDINGS (B) (see Note 12)
+
<
1) Less than 15 m in height

i) Ground plus one R NR NR NR NR R NR NR NR 5000 NR 450


storey (see Note 2) (see Note 3) (see Note 3)

ii) Ground plus two R R NR NR NR NR R NR NR NR 10000 NR 450


or more storeys (see Note 2) (5 000) (450)
(see Note 4) (see Note 4)

2) 15 m and above but not R R NR NR R R R NR NR 25000 NR 900


exceeding 30 m in height (see Note 2)

INSTITUTIONAL BUILDINGS (C) (see Note 12)

a) Hospitals, Sanatoria
and Nursing Homes
(c-l)
1) Less than 15 m in height
with plot area up to
1000 m2

i) Up to ground plus R R NR NR NR R R NR NR 2500 NR NR


one storey, with (see Note 2) (2 500)
no beds (see Note 4)

ii) Up to ground plus R R NR NR R R R NR NR 5000 NR 450


one storey with beds (see Note 2) (5 000) (450)
(see Note 4) (see Note 4)
iii) Ground plus two R R NR NR R NR R R R NR 5000 NR 450
or more storeys, (see Note 2) (5 000) (450)
with no beds (see Note 4) (see Note 4)

iv) Ground plus two or R R NR R NR NR R R R 50000 5000 (see Note 19) NR


more storeys, with (see Note 2) (5 000)
beds (see Note 4)

.@
*>
‘ ,*
1 alne u — Continued

(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15)

2) Less than 15 m in height R R NR R NR R R R R 100000 10000 (see Note 19) NR


with plot area more (see Note 2)
than 1000 m2

3) 15 m and above but not R R NR R NR R R R R 100000 20000 (see Note 20) NR


exceeding 24 m in height (see Note 11)

4) Above 24 m and not R R NR R NR R R R R 150000 20000 (see Note 21) NR


exceeding 30 m in height (see Note 11)

b) Custodial (C-2), and


Penal and PIental (C-3)
1) Less than 10 m in
height
i) Up to 300 persons R R NR NR NR NR R R NR NR 10000 NR 450 (900)
(see Note 2) (5 000) (see Note 4)
(see Note 4)

ii) More than 300 R R NR NR R NR R R NR NR 15000 . NR 450 (900)


persons (see Note 2) (5 000) (see Note 4)
(see Note 4)

2) 10 m and above but R R NR R NR R R R R 50000 5000 (see Note 20) NR


not exceeding 15 m (see Note 2) (5 Ooo)
in height (see Note 4)

3) 15 m and above but R R NR R NR R R R R 75000 10000 (see Note 20) NR


not exceeding 24 m in (see Note 11) I
height

4) 24 m and above but R R NR R NR R R R R 100000 20000 (see Note 21) NR


not exceeding 30 m in (see Note 11)
height
.

ASSEMBLY BUILDINGS (D) (see Note 12)

a) Buildings
(D-1 to D-5)
1) Less than 10 m in height

i) Up to 300 persons R R NR NR R NR R R NR NR 10000 NR 450


(see Note 2) (5 000) (450)
(see Note 4) (see Note 4)

,$
? Table 23 —Continued
~
& (1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15)
ii) Morethan R R NR NR R NR R R NR NR 15000 NR 900
300 persons (seeNote 2) (5 000)
(~eeNote 4)
2) Above10m but not R R NR R NR NR R R R 50000 5000 (see Note 20) 450
exceeding15m in height (see Note2) (5 000) (450)
(seeNote4) (seeNote4)
3) Above 15m but not R R NR R NR R R R R 75 m 1000O (seeNote 20) NR
exceeding24 m in height (seeNote 11)

4) Above24 m but not R R NR R NR R R R R 100000 200011 (see Note 21) NR


exceeding30 m in height (seeNote 10)

b) Multiplex D-6 R RNR R NR R R R R 200000 20000 (seeNote22) NR


(seeNote 10)
c) D-7 Fordetailssee6.4.8
BUSINESS BUILDINGS (E)

1) Lessthan 10m in R R NR NR R NR R R NR NR 1000O NR 450


height (seeNote2) (5 Ooo) (450)
(seeNote4) (seeNote 4)

2) Above 10m but not R R NR R NR NR R R R 50000 (see Note20) 450


exceeding15m in (seeNote2) (; W) (450)
height (seeNote4) (seeNote4)

3) Above 15m and ,W to R R NR R NR R R R R 75 O(N 10000 (see Note 20) NR


24 m in height (fee Note 11)
4) Above24 m and up to R R NR R NR R R R R 100 0@3 20000 (see Note 21) NR
30 m in height (seeNote 10)
5) Above30 m in height R ..\R NR R NR R R R R 200000 20000 (see Note 22) NR
(seeNote 10)
MERCANTILE BUILDINGS (F)

a) F-1 & F-2


(see Note 12)

1) Less tbsn 15 m in height

i) Groundplus one R R NR NR R NR R NR m NR 5000 NR 450


stofey,withtotal (seeNo@2) (5 Ooo) (450)
coveredareanot (see Note 4) (see Note 4)
exceeding500 mz
u
m
Table 23 — Continued

(1) (2) . (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15)
ii) Groundplus one R R NR NR R NR R R NR NR 25 (XXI NR 900
storeyand covesed (seeNote 2)
area exceeding
500 mz

iii) Morethan ground R R R NR R NR R R NR NR NR 900


plus one storey (see Note 2) (:%)
(seeNote4)
2) Above 15m but not R R NR R NR NR R R R 100(Do 10Ocml (seeNote 20) NR
exceeding24 m in (seeNote 11)
height

3) Above24 m but not R R NR R NR R R R 150000 10IXKl (seeNote 21) NR


exceeding30 m in (seeN& 10)
height

b) Underground shopping R R NR R NR R R R 150000 100CK) (seeNote 21) NR


complex (F-3) (seeN~te 10)
(seeNote 13)

INDUSTRIAL BUILDINGS(G) (seeNote 14)


a) hw Hazard (G-1)
(see Note 15)

i) Builtup area R NR NR NR NR NR NR NR NR 5000 NR 450


up to 100mz (see~ote 2) (seeNote3) (seeNote 3)
ii) Builtup areamom R R NR NR R NR NR NR NR NR 450
than 100mz and (see ~ote 2) (:%)
up to 500 mz (seeNote4)

iii) Built up areamom R ...$ F& R R R R NR R 100 txlo 10000 (seeNote 20) 450
than 500 mz (see Note 7)

b) Moderate Haard
(G2) (see Note 14)

i) Built up srea R R NR NR NR NR R NR NR NR 10000 NR 450


upto100m2
ii) Built up area more R R NR NR NR NR R NR NR NR 10000 NR 900
than l(X)m2 and
up to 500 m2
? Table 23 — Continued
g
.P (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15)

E iii) Builtup areamore


than 500 mzand
R R NR R R
(seeNote7)
R R R R 75 000 20 Oco (seeNote20) 900

upto1000m2
E
iv) Builtup areamore R R NR R R R R R R 100 O(M 20000 (seeNote20) 900
i tharr1000m2 (seeNote7)
~
C) ~ ~zard (G-3)
8 (seeNote 16)
=!
i) Builtup area R R NR NR NR NR R NR NR m 5000 NR 450
up to 50 mz

ii) Built up areamore R R NR NR NR NR R NR R NR 5000 NR 450


than 50 mz and
up to 150m2

iii) Builtup areamore R R NR R NR NR R NR R 25000 10000 (seeNote 19) 450


than 150m2and
up to 300 m2

iv) Builtup areamore R R NR R NR R R R R 50000 20000 (seeNote 19) 900


than 300 m2and
up to 500 m2

v) Builtup am.amore R R NR R R R R R R 100000 20 m (seeNote 20) 900


than 500 mz (seeNote7)

STORAGE BUILDINGS (H) (see Note 17)

1) Below 15m io height R R NR NR NR NR R NR NR 25 OMt 5000 (seeNote 19) 450


and coveredamaless
thatr250 mz ‘.

2) Below 15m in height


and coveredareamore
tharr250mz

i) Groundfloor only R R NR R NR R R NR R 50 Olm 10000 (seeNote 20) 450

ii) Groundplus R R NR R NR R R NR R 75000 10 OtMl (seeNote 20) 450


one flooi
Table 23 — Concluded

(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15)

iii) Morethan ground R R NRR NR R R NR R 100000 10000 (seeNote20) 450


plus one floor

HAZARDOUS BUILDINGS (J) (see Note 17)

1) Up to 15m in height

i) SingleStorey R R NRNR NR R R R R Minimum NR (seeNote 18) NR


Building 4 h fue
fighting
requirements

ii) Morethan one floor R R NR R R R R R R Minimum 50 O(XI (seeNote 18) 900


buildingbut not 4hfire
exceeding15m fighting
requirements

R — Required
NR — Not Reqnired
NOTES
1 Buildingsabove15m in height not to be permittedfor occupanciesA-1 and A-2.
2 Requiredto be installedin basementif area of basementexceeds200 m’.
3 Requiredto be providedif basementarea exc~ds 200 mz.
4 Additionalvalue given in parenthesisshallbe addedif basementarea exceeds200 m’.
5 Requiredto be providedfor buildingswith more than two storeys(Ground+ One).
6 As per the requirementof local authorityDry Riser maybe used in hilly areas,industrialareasor as required.
7 Requiredto be providedfor buildingswith height i%ove15 m.
8 To be installedin basement. If basementprovi&d is used for car parkingand area thereofexceeds750 m’ then the sprinklersshall be fed water from both undergroundstatic water storagetank and
terrace tank.
9 R~~ to be providedfor boil~$ withrnoia than one storey.
10 To be iostalkd in entite building. “
11 TObe iostal.ledirrall floors at appropriateplaces and in consultationwith 10CSI
fire authorities.
12 Buildittgsshove 30 m in height not to be permittedfor GroupB, GroupC, Group D sad Group F occupancies.
13 All n@ergroundshoppingareas shouldbe folly air-conditioned.
14 The requirementsgiven in this table for GroupG IndustrialBuildingsare for small scaleindustryunits. For other industriesthe requirementswill have to be workedout on the basis of relevantIndian
Stsmkwdsand also in consultationwith the local tire authorities.
15 Buildkgs above 18 m in height not to be permittedfor G-1 and G-2 occupancies.
16 Buildingsabove 15m in heightnot to he permittedfor G-3 crccupancies.
17 Buildingsabove 15m in height not to be permittedfor GroupH end GroupJ occupancies.
LEGENO :-
II, F.1 DIESEL ORIVEN FIRE PUMP

-& F-2
F-3
F4
EL. HYDRANT FIRE PUMP
JOCKEY PUMP
EL. SPRINKLER PINP
.

Pv PRESSURE VESSEL
FH FIRE NYDRANT
—x— VN.VS

,3n- .’
~
—i-.
FLEXISLE C0NNEC70N
NON RETURN VALVE

WIRING TO FAP
OL VALVE
nil. /7 /-FIANGE JOINT

------ SWITCH
.. . ..
l=
FLOW

WTiE::
DETAIL-’A’

b F

F’”% t
0.S0 m

FIRE RISER FROM


GR. FL.
ELEVATIONAL VIEW 111111
‘FltW PIANT ROOM
SPRINKLERRISER FROM
FIRE PLANT ROOM
IF SPRINKLERORAIN
PIPE TO FIRE TANK

TO E)O_ERNAL FIRE
HYDRANT
=’LEF’”WA”T”
(EXTERNAL)
- w

1776 I &
TO SPRINKLER
SYSTEM 4 1-1 I F4 I I FIRE
. .. WATER
.... TAMC-2
. . .
.

FIRE WMP ROOM

PLAN

FIG. 5 TYPICAL SYSTEM OF PUMPING WITHTwo ELECTRIC,


ONE DIESEL FIRE PUMP

PART 4 FIRE ANDLIFE SAFETY


5.1.3 In situations where one occupancy is provided b) The static water storage tank shall be provided
with all the required fire protection arrangements but with a fire brigade collecting head with 4
due to proximity of unprotected buildings around, number 63 mm diameter (2 number 63 mm
causing exposure hazard to the protected building, the diameter for pump with capacity 1400 Mnin)
protected building walls facing the unprotected instantaneous male inlets arranged in a valve
building shall be made of the requisite fire resistance box at a suitable point at street level and ‘
rated materials or alternatively provided with water connected to the static tank by a suitable fixed
curtainldrencher system which can be actuated, when pipe not less than 150 mm in diameter to
necessary. discharge water into the tank when required
at the rate of 2250 I/tin, if tank is in the
5.1.4 First-aid fire fighting appliances shall be
provided and installed in accordance with good practice basement or not approachable for the fire
[4(21)]. The fire fighting equipment and accessories engines.
to be installed in buildings for use in fire fighting shall 5.1.7 Automatic Sprinklers
be in accordance with the accepted standards contained
in [4(20)] and shall be maintained periodically so as Automatic sprinklers shall be installed in:
to ensure their perfect serviceability at all times. a) basements used as car parks or storage
5.1.5 In addition to wet riser or down-comer, first-aid occupancy, if the area exceeds 200 mz;
hose reels shall be installed on all the floors of buildings b) multi-level basements, covered upper floors
of 15 m in height or more and shall be in accordance used as car parks, and for housing essential
with accepted standards [4(22)]. The first-aid hose reel services ancillary to a particular occupancy
shall be connected directly to the riser/down-comer or for storage occupancy, excluding any area
main and diameter of the hose reel shall not be less to be used for sub-station, A.C. plant and DG
than 19 mm. set;
c) any room or other compartment of a building
5.1.6 Static Water Storage Tanks
exceeding 1 125 m2 in area except as in (g)
A satisfactory supply of water for the purpose of fire (see Note 1), if so advised by local authority;
fighting shall always be available in the form of d) departmental stores or shops, if the aggregate
underground/terrace level static storage tank with covered area exceeds 500 mz;
capacity specified for each building with arrangements
e) all non-domestic floors of mixed occupancy
or replenishment by mains of alternative source of
which constitute a hazard and are not provided
supply at the rate of 1000 I/rein for underground static
with staircases independent of the remainder
tank. When this is not practicable, the capacity of static
of the buildings;
storage tank(s) shall be increased proportionately in
f) godowns and warehouses, as considered
consultation with the local iire brigade.
necessary;
The static storage water supply required for the above
g) on all floors of the buildings other than
mentioned purpose shall entirely be accessible to the
residentird and educational buildings, if the
fire engines of the local fire service. Provision of
height of the building exceeds 15 m (45 m in
suitable number of manholes shall be made available
case of group housing and apartments) (see
for inspection, repairs, insertion of suction hose,
Note 1);
etc. The covering slab shall be able to withstand the
h) dressing rodm, scenery docks, stages and
total vehicular load of 45 T equally divided as a four
point load when the slab forms a part of pathwayl stage basements of theatres;
driveway. j) in hotels, hospitals, industries low and
moderate haz!ard mercantile buildings of
The domestic suction tank connected to the static water
height 15 m or above;
storage tank shall have an overflow capable of
discharging 2250 lhnin to a visible drain point from k) in hotels below 15 m, if covered area at each
which by a separate conduit, the overflow shall be floor is more than 1000 mz;
conveyed to a storm water drain. m) false ceiling voids exceeding 800 mm in
height (see Note 2); and
a) To prevent stagnation of water in the static
n) canteen provided in upper floors of D-1
water storage tank, the suction tank of the
domestic water supply shall be fed only and D-2 occupancies shall be sprinklered.
through an ovefflow arrangement to maintain NOTES
the level therein at the minimum specified 1 It is desirable that all high rise buildings should be fully
capacity (see Fig. 6). sprinklered irrespective of their height and occupancy. If

46 NATIONALBUILDING CODE OF INDIA


-

4 Nos. 0 63 mm
INLET
——
VALVE BOX
I
/ CABINET
A [

PRIME
MOVER 7 r FIRE
I
L. — .i
MANHOLE

TOWN MAIN ~ OVERFLOW


SUPPLY AND VENT

t! GL
———. ~-——— ———
—--- 4-——— 2 s z —-- A m-s
,
f w
FIRE , J < SEPARATION
u.
FIGHTINGk > WALL
-A, .- –-––

6A WITH NEGATIVE SUCTION

4 Nos.063 mm
F. B. INLET
VALVE BOX ———
1
/ CABINET I I
\ \ I I
I I
OVERFLOW
) $ I
AND VENT
DOMESTIC WATER
SUPPLY TANK (OTHER SUPPLY L. . -- -1
THAN DRINKING WATER)

SEPARATION WALL

SLUICE 0 ~~ mm
TO DOMESTIC
X PUMP SUCTION PRIME

SLUICE
VALVE

GL

3B WITH POSITIVE SUCTION

FIG. 6 TYPICAL ARRANGEMENT FOR PROVIDING COMBIND FIRE FIGHTINGAND


DOMESTICWATER STORAGETANK

PART 4 FIRE ANDLIFE SAFETY 47


F--

[4(24)] on premises where water or foam cannot be A-5 as specified in Table 23 and Annex C (for High
used for fire extinguishing because of the special nature Rise Buildings) shall apply.
of the contents of the buildings/areas to be protected.
6.1.3 Exit Facilities
For some special fire risldessential applications, carbon
dioxide may not be suitable and it may be necessary to The capacity of any open mezzanine or balcony shall
provide BCF (Bromochlorodifluoromethane) — Halon be added to the capacity of the floor for the purpose of
1211 or BTM (Bromochlorotrifluoromethane) — determining the exit capacity.
HaIon 1301 or some other identified substitutes.
6.1.3.1 In addition to requirements specified for
However, the use of halons shall be discouraged, as occupancy sub-division A-2, the following shall be
halons are ozone depleting substances (ODS) and their provided for occupancy sub-division A-1:
use is being phased out throughout the world.
Every sleeping room above the street floor shall
5.1.11 Fire fighting equipment shall be suitably have access to two separate means of exits, at least
located and clearly marked by luminous signs. one of which shall consist of an enclosed interior
NOTE — This provision shall not apply to occupancies A-2
stairway, or a fwe escape or horizontal exit all so
and A-4 less than 15 m in height. arranged as to provide a safe path of travel to the
outside of the building without traversing any
5.2 Fire Detection/Extinguishing System
corridor or space exposed to an unprotected
In buildings of such size, arrangement or occupancy vertical opening.
that a fire may not itself provide adequate warning to
6.1.3.2 For occupancy sub-division A-2 of more than
occupants, automatic fire detection and alarm facilities
two rooms, every occupied room, excluding areas used
shall be provided, where necessary, to warn occupants
solely for storage shall have at least two means of exits,
early of the existence of fire, so that they may escape,
at least one of which shall be a door or a stairway
or to facilitate the orderly conduct of fire exit drills.
providing a means of un-obstructed travel to the outside
5.2.1 The fire detection and extinguishing system shall of the building or street or grade level. No room or
be in accordance with accepted standards [4(18)]. space shall be occupied which is accessible only by a
Guidelines for selection of various types of fire ladder, folding stairs or through a trap door.
detectors for different occupancies shall be in
Further the following provisions shall be made:
accordance with good practice [4( 19)]. Addressable
analog fire detection system shall be preferred. Ali locking devices, which would impede or
prohibit exit, such as chain type bolts, limited
5.2.2 The requirements of fire detection and alarm
opening sliding type locks and burglar locks,
systems are also covered for each occupancy in 6.1
which are not dis-engaged easily by quick-
to 6.9; and for high rise buildings (15 m or more in
releasing catches, shrdl be prohibited. All closet
height) in Annex C.
door latches shall be such that even children c~
5.3 Fire Extinguisher/Extinguishing System Using open the doors from inside. All bathroom door
Halon Alternatives locks or fasteners shall be designed to permit the
opening of the locked or closed door from the
Provisions for certain fue extinguishers and extinguishing outside in an emergency without the use of a
systems for fire protection which may be used as halon special key.
alternatives, shall be in accordance in [4(25)].
6.1.3.3 For occupancy sub-division A-3, the following
6 ADDITIONAL OCCUPANCY-WISE provisions shall apply:
REQUIREMENTS
All dormitories shall lrttve exits so arranged that
6.1 Requirements of Residential Buildings (Group A) from any sleeping room or open dormitory
sleeping area, there shall be access to two separate
6.1.1 In addition to the general requirements for the
and distinct exits in different directions with no
type of construction and occupancy group specified
common path of travel unless the room or space
in 3.4 and the exit requirements given in 4, the
is subject to occupancy by not more than 10
requirements 6.1.2 to 6.1.4.10 shrdl be complied with.
persons and has a door opening directly to the
The capacity of any open mezzanine or balcony shall
outside of the building at street or grade level, or
be added to the capacity of the floor below for the
to an outside stairway in which case one means of
purpose of determining exit capacity.
exit may be accepted.
6.1.2 Fire Detection/Extinguishing System
6.1.3.4 For occupancy sub-division A-4, the following
The requirements for occupancy sub-divisions A-1 to provisions shall apply:

PART 4 FIRE ANDLIFE SAFETY 49


a) Every individual living unit covered by storage and service operations (other than
occupancy sub-division A-4 shall comply kitchens, which are considered part of the hotel
with the requirement for occupancy sub- occupancy) shall have exits appropriate to the
division A-2 in respect of exits. actual occupancy, in accordance with other
b) Every living unit shall have access to at least applicable provisions of the Code, or in case
two separate exits, which are remote from of mixed occupancy where there maybe doubt
each other and are reached by travel in as to which other section is applicable, such
different directions, except that a common basements shall have exits determined on the
path of travel may be permitted for the first basis of lesser exit capacity.
6 m (that is a dead end corridor up to 6 m long
may be permitted) provided that single exit 6.1.4 Additional Precautions
may be permitted under any of the conditions 6.1.4.1 Flammable liquids for household purposes
given under (c). shall be kept in tightly stoppered or sealed containers.
c) Any part of building lower than the grade For the limits of quantities of flammable liquids to be
level shall have direct accessibility from allowed in various occupancies, reference maybe made
outside. to appropriate regulations.
d) At least half of required exits shall discharge
6.1.4.2 No stove or combustion heater shall be located
direct to the outside of the buildings; any
directly under or immediately at the foot of stairs or
other exit shall be the same as required for
otherwise so located as to block escape in case of
hotels.
malfunctioning of the stove or heater.
.-
6.1.3.5 For occupancy sub-divisions A-5 and A-6, the
6.1.4.3 All kitchen exhaust fans, where provided, shall
following provisions shall apply:
be fixed to an outside wall or to a duct of non-
a) Not less than two exits, as remote from each combustible material, which leads directly to the
other as practicable, shall be accessible from outside. The ducts must not pass through areas having
every floor, including basements occupied for combustible materials.
hotel purpose, except as a single exit as
permitted in (b) below. Exits and ways of 6.1.4.4 All wiring shall be done in accordance with
access thereto shall be so arranged that they Part 8 ‘Building Services, Section 2 Electrical
are accessible in at least two different Installations’, good practice [4(10)] and National
directions from every point in any open area, Electric Code.
or from any room door. 6.1.4.5 Where television is installed, all outdoor
b) Any room or section with an outside door at antennae shall be properly grounded and protected
street or grade level may have such outside from lightning (see Part 8 ‘Building Services, Section 2
door as a single exit, provided no part of the Electrical Installations’).
room or area is more than 15 m from the door
measured along the natural path of travel. 6.1.4.6 Doors leading to rooms in which flammable
liquids are stored or used shall be as in 4.7. Such
c) Provision of panic bars shall be provided in
assembly shall be self-closing and shall be posted with
the exits.
a sign on each side of the door in 25 mm high block
6.1.3.5.1 Where stairways or other exits serve two or letters stating — ‘FIREDOOR — KEEP CLOSED’.
more upper floors, the same stairway or other exit
6.1.4.7 Where a boiler room is provided or a central
required to serve any one upper floor may also serve
heating plant is installed, which uses solid or liquid
other upper floors, except that no inside open stairway
fuel, it shall be separated ~om rest of the building by a
or ramp may serve as a required egress facility from
separation wall with al Lopenings protected as in 3.4.7
more than one floor [see good practice 4(26)].
and 3.4.8.
6.1.3.6 Basement Exits
6.1.4.8 Rooms containing high pressure boilers,
a) Basements occupied for hotel purposes shall refrigerating machinery, transformers or other service
have exits arranged in accordance with 6.1.3.5. equipment subject to possible explosion shall not be
b) Basement exits shall be sufficient to provide located directly under or adjacent to exits. All such
for the capacity of the basement as determined rooms shall be effectively cut off from other parts of
in accordance with 6.1.1. In no case shall there the building and shall be provided with adequate vents
be less than two independent basement exits. to the outside air.
c) Basement or sub-basements not open to the 6.1.4.9 All rooms or areas of high hazard in additions
public and used only for heating equipment, to those herein before mentioned, shall be segregated

50 NATIONAL BUILDING CODE OF INDIA


or shall be protected as may be directed by the marked. The detailed requirements regarding safe use
enforcing Authority where, in the opinion of the of gas shall be as specified in Part 9 ‘Plumbing
enforcing Authority, fire, explosion or smoke there Services, Section 3 Gas Supply’.
from is likely to interfere with safe egress from the
6.2.5.3 All exterior openings in a boiler room or rooms
building.
containing central heating equipment, if located below
6.1.4.10 For detailed information regarding fire safety opening in another storey or if less than 3 m from other
requirements for hazardous petroleum products, doors or windows of the same building, shall be
reference may be made to the Petroleum Act, 1934 protected by a fire assembly as in 3.4.8. Such
and the Rules thereof. assemblies shall be fixed, automatic or self-closing.
Provisions of 6.1.4.7 shall also apply to this group of
6.2 Requirements of Educational Buildings occupancy.
(Group B)
6.2.6 Exception and Deviation
6.2.1 In addition to the general requirements specified
in 3.4 for the type of construction and occupancy group 6.2.6.1 Gymnasiums, indoor stadiums and similar
and the exit requirements given in 4, the requirements occupancies may have floorslrunning tracks of wood,
given in 6.2.2 to 6.2.6.3 shall be complied with. cinder, synthetic or unprotected steel or iron.

6.2.2 Buildings intended for educational occupancy 6.2.6.2 In gymnasiums and in multi-purpose school
shall not be used for any hazardous occupancy. rooms having an area not greater than 300 mz, 25 mm
nominal tight tongue-and-grooved or 20 mm plywood
6.2.3 Fire Detection/Extinguishing System
wall covering may be used in the inner side in lieu of ---
The requirements for occupancy sub-divisions B-1 and fire-resistant plaster.
B-2 as specified in Table 23 and Annex C (for High
6.2.6.3 A building, which will have only the first floor
Rise Buildings) shall apply.
and is accessible to not more than 20 pupils at any
6.2.4 Exit Facilities time, may be used for school purposes with the
following exceptions:
The capacity of any open mezzanine or balcony shall
be added to the capacity of the floor for the purpose of a) Exterior walls or parts of walls which are less
determining the exit capacity. than 900 mm from adjacent property lines
shall have no openings therein.
In addition to the provisions in 4, the following shall
be provided: b) Classrooms may have only one exit not less
than 900 mm wide.
6.2.4.1 Exits, in accordance with 4 shall be so arranged
that at least two separate exits are available in every 6.3 Requirements of Institutional Buildings
floor area. Exits shall be as remote from each other as (Group C)
practicable and so arranged that there are no pockets
6.3.1 In addition to the general requirements specified
or dead ends of appreciable size in which occupants
in 3.4 for the type of construction and occupancy group
may be trapped.
and the exit requirements given in 4, the requirements
6.2.4.2 Every room with a capacity of over 45 persons given in 6.3.2 to 6.3.5 shall be complied with.
in area shall have at least two doorways.
6.3.2 Fire Detectior@xtinguishing System
6.2.4.3 Exterior doors shall be operated by panic bars
The requirements for occupancy sub-divisions as
or some other panic hardware device, except that doors
specified in Table 23 and Annex C (for High Rise
leading from classrooms directly to the outside may
Buildings) shall apply. ‘
be equipped with the same type of lock as is used on
classroom doors leading to corridor, with no provision 6.3.3 Exit Facilities
whatsoever for locking against egress from the In addition to the provisions of 4, the following
classroom. requirements shall be complied with.

6.2.5 Additional Precautions 6.3.3.1 In buildings or sections occupied by bed-


ridden patients where the floor area is over 280 mz,
6.2.5.1 Storage of volatile flammable liquids shall be
facilities shall be provided to move patients in hospital
prohibited and the handling of such liquids shall be
beds to the other side of a smoke barrier from any part
restricted to science laboratories only.
of such building or section not directly served by
6.2.5.2 Each building shall be provided with an approved horizontal exits or exits from the fust floor
approved outside gas shut-off valve conspicuously (floor 2) of a building to the outside.

PART 4 FIRE AND LIFE SAFETY 51


6.3.3.2 Not less than two exits of one or more of the stored or used in any building or section thereof used
following types shall be provided for every floor, for institutional occupancy, except as necessary to
including basement, of every building or section: normal occupancy and use of the building.

a) Doors leading directly outside the building; 6.3.4.2 Bare minimum quantities of flammable
b) Stairways; material such as chloroform, ethyl alcohol, spirit, etc
c) Ramps; shall be allowed to be stored and handled. The handling
of such liquids shall not be permitted by un-authorized
d) Horizontal exits; and
persons. Bulk storage of these items, will be governed
e) Fire tower. by relevant rules and safe practices.
6.3.3.3 All required exits that serve as egress from
6.3.5 Exceptions and Deviations
hospital or infirmary sections shall be not less than
2 m in clear width including patient bedroom doors to It is recognized that in institutions or part of buildings
permit transportation of patients on beds, litters, or housing various types of psychiatric patients, or used
mattresses. The minimum width of corridors serving as penal and mental institutions, it is necessary to
patients bedrooms in buildings shallbe2400 mm. For maintain locked doors and barred windows; and to such
detailed information on recommendations for buildings extent the necessary provision in other sections of the
and facilities for the physically handicapped, reference Code requiring the keeping of exits unlocked may be
may be made to good practice [4(27)]. waived. It is also recognized that certain type of
psychiatric patients are not capable of seeking safety
6.3.3.4 Elevators constitute a desirable supplementary
without adequate guidance. In buildings where this
facility, but are not counted as required exits. Patient --
situation prevails, reliable means for the rapid release
lifts shall also be provided with enough room for
of occupants shall be provided, such as remote control
transporting a stretcher trolley,
of locks, or by keying all locks to keys commonly used
6.3.3.5 Any area exceeding 500 m2 shall be divided by attendants.
into compartments by fire resistant walls.
6.4 Requirements of Assembly Buildings (Group D)
6.3.3.6 Doors in fire resistant walls shall be. so installed
that these may normally be kept in open position, but 6.4.1 In addition to the general requirements specified
will close automatically. Corridor door openings in in 3.4 for type of construction and occupancy group
smoke barriers shall be not less than 2000 mm in width. and the exit requirements given in 4, the requirements
Provision shall also be made for double swing single/ given in 6.4.2 to 6.4.8.9 shall be complied with.
double leaf type door.
6.4.2 Mixed Occupancy
6.3.3.7 Exits and other features for penal and mental
Places of assembly in buildings of other occupancy,
institutions, and custodial institutions shall be the same
such as ballrooms in hotels, restaurants in stores and
as specified for hospitals, in so far as applicable.
assembly rooms in schools, shall be so located,
Reliable means shall be provided to permit the prompt
separated or protected as to avoid any undue danger to
release of inmates from any locked section in case of
the occupants of the place of assembly from a fire
fire or other emergency.
originating in the other occupancy or smoke therefrom.
6.3.3.8 Wherever any inmates are confined in any locked
rooms or spaces, adequate guards or other personnel shall 6.4.3 Fire Detectiotixtinguishing System
be continuously on duty or immediately available to The requirements for &cupancy sub-divisions D-1 to
provide for release of inmates or for such other action as D-5 as specified in Tdble 23 and Annex C (for High
may be indicated in case of fue or other emergency. Rise Buildings) shall ap~ly.
6.3.3.9 No building constructed in whole or in part of NOTE — Canteens sh~l not be provided in basements. If
combustible materials shall be used to confine inmates provided in the upper flmrs, it shalt be sprirddered.
in cells or sleeping quarters, unless automatic sprinkler
6.4.4 Exit Facilities
protection is provided.
6.4.4.1 Every place of assembly, every tier or balcony,
6.3.3.10 All buildings or sections of buildings in penal
and every individual room used as a place of assembly
and mental institutions used for manufacturing, storage
shall have exits sufficient to provide for the total
or office purposes shall have exits in accordance with
capacity thereof as determined in accordance with 4.
the provisions of the Code for those occupancies.
Door width for assembly buildings shall not be less
6.3.4 Additional Precautions than 2000 mm.

6.3.4.1 No combustible material of any kind shall be a) Every place of assembly of sub-division D-1

52 NATIONAL BUILDING CODE OF INDIA


shall have at least four separate exits as remote All displays or exhibits of combustible material or
from each other as practicable. construction and all booths and temporary construction
b) Every place of assembly of sub-division in connection therewith shall be so limited in
D-2, shall have at least two separate exits as combustibility or protected as to avoid any undue
remote from each other as practicable and if hazard of fire which might endanger occupants before
of capacity over 600 at least three exits shall they have opportunity to use the available exits, as
be provided with each exit not less than of determined by the authority.
2000 mm width. 6.4.4.8 Places of assembly in buildings of other
6.4.4.2 Clear aisles not less than 1.2min width shall occupancy may use exits common to the place of
be formed at right angles to the line of seating in such assembly and the other occupancy, provided the
number and manner that no seat shall be more than seven assembly area and the other occupancy are considered
seats away from an aisle. Rows of seats opening on to separately, and each has exits sufficient to meet the
an aisle at one end only shall have not more than seven requirements of the Code.
seats. Under the conditions, where all these aisles do 6.4.4.9 Exits shall be sufficient for simultaneous
not directly meet the exit doors, cross-aisles shall be occupancy of both the places of assembly and other
provided parallel to the line of seating so as to provide parts of the building, unless the Authority determines
direct access to the exit, provided that not less than one that the conditions are such that simultaneous
cross aisle for every 10 rows shall be required. The width occupancy will not occur.
of cross-aisles shall be minimum of 1 m. Steps shall not
6.4.4.10 For any place of assembly under sub-division
be placed in aisles to overcome differences in levels,
D-1, at least half the required means of exits shall lead
unless the gradient exceeds 1 in 10.
directly outdoors or through exit ways completely
6.4.4.3 The fascia of boxes, balconies and galleries separated from exits serving other parts of the building.
shall have substantial railings not less than 1000 mm
6.4.4.11 For detailed information regarding cinema
high above the floor. The railings at the end of aisles
buildings, reference may be made to good practice
extending to the fascia shall be not less than 1 100 mm
[4(28)].
high for the width of the aisle or 1200 mm high at the
foot of steps. 6.4.5 Lighting
6.4.4.4 Cross-aisles except where the backs of seats No open flame lighting devices shall be used in any
on the front of the aisle project 600 mm or more above place of d>>
‘---–~’--
G1llU1y ‘-----’ 111
, CACt+JL ‘- ‘~- ‘-’’---’--
LUG lU1lU Wlll~ ‘----” ;
lXISGi

the floor of the aisle shall be provided with railings


not less than 900 mm high. a) Where necessary for ceremonial purposes, the
enforcing Authority may permit open flame
6.4.4.5 No turnstiles or other devices to restrict the lighting under such restrictions as are
movement of persons shall be installed in any place of necessary to avoid danger of ignition of
assembly in such a manner as to interfere in any way combustible materirds or injury to occupants.
with the required exit facilities. b) Candles may be used on restaurant tables if
6.4.4.6 In theatres and similar places of public securely supported on non-combustible bases
assembly where persons are admitted to the building and so located as to avoid danger of ignition
at a time when seats are not available for them and are of combustible materials.
allowed to wait in a lobby or similar space until seats c) Open flame devices may be used on stages
are available, such use of lobby or similar space shall where they are a necessary part of theatrical
not encroach upon the required clear width of exits. performance, provided adequate precautions,
Such waiting shall be restricted to areas separated from satisfactory to’ the Authority are taken to
the required exit ways by substantial permanent prevent ignition of combustible materials.
partitions or fixed rigid railing not less than 105 cm
6.4.6 Additional Precautions
high. Exits shall be provided for such waiting spaces
on the basis df one person for each 0.3 m2 of waiting 6.4.6.1 The decorations of places of assembly shall
space area. Such exits shall be in addition to the exits be of non-flammable materials. Fabrics and papers used
specified for the main auditorium area and shall for such purpose shall be treated with an effective
conform in construction and arrangement to the general flame-retardant material. Stage settings made of
rules of exits given above. combustible materials shall likewise be treated with
fire retardant materials of Class 1 flame spread.
6.4.4.7 No display or exhibit shall be so installed or
operated as to interfere in any way with access to any 6.4.6.2 Seats in places of public assembly,
required exit, or with any required exit sign. accommodating more than 300 persons, shall be

PART 4 FIRE ANDLIFE SAFETY 53


securely fastened to the floor, except as permitted 6.4.6.8 The stage roof of every theatre using movable
in 6.4.6.3. All seats in balconies and galleries shall be scenery or having a motion picture screen of highly
securely fastened to the floor, except that in nailed-in combustible construction shall have a ventilator or
enclosures, boxes with level floors and having not more ventilators in or above it, openable from the stage floor
than 14 seats, the seats need not be fastened. by hand and also opening by fusible links or some other
approved automatic heatismoke actuated device, to
6.4.6.3 Chairs not secured to the floor may be
give a free opening equal to at least one-eighth the
permitted in restaurants, night clubs and other
area of the floor of the stage.
occupancies where the fastening of seats to the floor
may not be practicable, provided that in the area used 6.4.6.9 The proscenium wall of every theatre using
for seating, excluding dance floor, stage, etc, there shall movable scenery of decorations shall have, exclusive
be not more than one seat for each 1.4 m2 of floor area of the proscenium opening, not more than two openings
and adequate aisles to reach exits shall be maintained entering the stage, each not to exceed 2 mz and fitted
at all times. with self-closing fire resistant doors.

6.4.6.3.1 Rows of seats between aisles shall have not 6.4.6.10 Every place of assembly in which projection
more than 14 seats. of motion pictures by light is made shall have the
projection apparatus enclosed in a fire-resisting fixed
6.4.6.3.2 Rows of seats opening on to an aisle at one
booth in accordance with good practice [4(27)], except
end only shall have not more than 7 seats.
that such booth shall not be required where no”
6.4.6.3.3 Seats without dividing arms shall have their nitrocellulose motion picture film is used.
capacity determined by allowing 450 mm per person.
6.4.6.11 Automatic smoke vents actuated by smoke
6.4.6.4 The spacing of rows of seats from back-to- detectors shall be installed above the auditorium or
back shall be neither less than 850 mm nor less than theatres, including motion picture houses, with vent
700 mm plus the sum of the thickness of the back and area equal to not less than 3 percent of the floor area
inclination of the back. There shall be a space of not of the auditorium, including the sum of the floor areas
less than 350 mm between the back of one seat and of all balconies, galleries, boxes and tiers. It may be
the front of the seat immediately behind it as measured desirable to provide a large number of small vents
between plumb lines. rather than a small number of large vents.

6.4.6.5 Rooms containing high pressure boilers, 6.4.7 Exception and Deviation
refrigerating machinery other than domestic
refrigerator type, large transformers or other service 6.4.7.1 Where boilers or central heating plants using
equipments subject to possible explosion shall not be liquid or solid fuel are located at grade level, these
Iocated directly under or adjacent to the required exits. shall be separated from the remainder of the building
All such rooms shall be effectively cut off from other by a separating wall with openings protected as in 3.4.7
parts of the building and provided with adequate vents and 3.4.8.
to the outer air. 6.4.7.2 Gymnasiums, indoor stadiums and similar
6.4.6.6 All rooms or areas used for storage of any occupancies may have floors/running tracks of wood,
combustible materials or equipment, or for painting, cinder, synthetic or un-protected steel or iron.
refinishing, repair or similar purposes shall be 6.4.7.3 The underside of continuous steel deck grand
effectively cut off from assembly areas or protected stands when erected outdoots need not be fwe-protected
with a standard system of automatic sprinklers. They when occupied for public toilets.
shall be located away from staircases.
6.4.8 Fire Protection and Fire
f Fighting System for
6.4.6.7 Every stage equipped with fly galleries, grid Metro Stations
irons and rigging for movable theatre type scenery,
6.4.8.1 Wet riser system
shall have a system of automatic sprinklers over and
under such stage areas or spaces and auxiliary spaces, Main and diesel fire pump of 1800 lhnin capacity to
such as dressing rooms, store rooms and workshops, be provided to support 3 to 4 hydrants at a time. Jockey
and the proscenium opening shall be provided with a pump capacity shall be 180 I/rnin. Where it is possible
fire- resisting curtain, capable of withstanding a lateral to extend reliable DG supply to the fue pump room
pressure of 4 kN/m2 over the entire area. The curtain without routing through the station building, the
shall have an emergency closing device capable of provision of diesel pump can be dispensed with and
causing the curtain to close without the use of power instead, two electric pumps may be provided out of
and when so closed, it shall be reasonably tight against which at least one should have DG back-up. The jockey
the passage of smoke. pump should also have DG back-up.

54 NATIONAL BUILDING CODE OF ININA


6.4.8.2 Internal hydrant false ceiling giving due consideration to depth of false
ceiling/flooring. However, in concourse, the detectors
The internal hydrant is proposed to be provided with
below false ceiling may not be effective due to heights/
2 number RRL hose pipes of 38 mm dia with 63 mm
cross ventilation and therefore may not be provided.
standard instantaneous coupling along with associated
In other areas, because of high heights and cross-
branch pipes and cabinet and a first aid hose reel of
ventilations, detectors will not be effective and hence
25mm dia, length 45m and fitted with 6.5mm
therefore can be dispensed. A conventional detection
nozzle.
system will suffice at a normal station.
Two internal hydrants are proposed to be provided on
6.4.8.5 Manual call box
each platform in such a way so that most of the platform
iscovered by hose. However, incaseof necessity, the Manual call box should be provided at a central place
hose pipes from other hose cabinets can be utilized for on each platform (near emergency plunger) and at least
extending the length of fire hose pipe for fire fighting, two on the concourse, on each sidewall. When the
if need be. At the concourse level minimum two concourse in two halves there should be one manual
hydrants will be provided. In station where the call box on each side.
concourse is split into two halves at least one hydrant
6.4.8.6 Manual panel gas jlooding
is to be provided in each half of the concourse. Further,
in case the area is more than 2000 m2, an additional Electric panels should have provision of manual gas
first aid hose-reel point shall be provided for every flooding. Alternatively panels can be provided with
additional 1000 mz. linear heat sensing tubes with C02 cylinder. This
In addition, hydrants shall be provided in commercial required to be provided only in main power panels,
that is HT panel, main LT panel, main LT distribution
areas also.
board and essential power panels and other such major
One hydrant shall be provided at entry of each station panels.
at ground floor for providing the coverage to the
parking area. 6.4.8.7 External area of the station

6.4.8.3 Sprinklers A ‘two waylfour way’ fire brigade inlet to be provided


at ground level on each rising main for hydrants/
Sprinklers are required to be provided only in the sprinkles.
commercial areas, if any, in the station. The commercial
areas will be segregated from the station area through The ‘Draw Off Connection’ shall be provided on the
2 h fire rated walls and doors. Additional sprinkler underground tank for fne brigade.
pumps are not required, as two pumps already provided
6.4.8.8 Water tank capacity
for hydrant system will take care of the sprinkler flow
requirements. Capacity of fire tanks at stations without any
commercial development (Beverage stall/ATM/Florist/
However, if such commercial areas in the premises of
Book stalls up to total 250 m2 excluded) shallbe50000 .
stations are in isolated building separate from the
litres.
station building then the provision of sprinkler pump
and water tank capacities shall be as per this Code. However, at stations having commercial development,
The water storage and pumps may however be the fire tank capacity shall be 100000 litres.
common.
6.4.8.9 Portable jire extinguishers
6.4.8.4 Detectors
For the purpose of standardization, the following
Detectors are required to be provided only in areas portable extinguishers are, recommended:
where there are false ceiling and false floor and areas
a) Water C02 type 9 litres
of equipment rooms. Wherever there are false ceiling,
the detectors should be provided both above and below b) COZ fire extinguishers 4.5 kg

PART 4 FIRE AND LIFE SAFETY 55


They shall be provided in various areas as detailed hereunder:

S1 Item Numbers and Location


No.
(1) (2) (3)

PLATFORM
1. Internal Hydrants Two at each platform. The hydrants at two platforms may be
staggered for maximum coverage.
2. Manual call box One on each platform preferably near emergency plunger.
3. Portable Extinguishers One set of Water COZ and C02 type on each platform at a central
area.
CONCOURSE
1. Internal Hydrants Two at each concourse. When concourse is in two parts then each
part should have at least one hydrant.
2. Additional first-aid reel point Additional fiist-aid reel point for every additional 1000 m2, if the
area is more than 2000 m2. Similarly, if the concourse is in two parts
then additional first aid reel point for every additional
1000 m2, if the area of the part is more than 1000 m2.
3. Manual call box Two at each concourse. When concourse is in two parts then each
part should have at least one.
4. Portable Extinguishers Two sets at each concourse. When concourse is in two parts then
each part should have at least one set.
5. Detectors Above false ceiling where depth of false ceiling is greater than
800 mm. Required in commercial areas also.

EQUIPMENT ROOM AREAS


1. Internal Hydrants/first-aid reel The requirement shall get covered with platfordconcourse.
point Additional first-aid reel point may be provided, if required.
2. Manual call box One at a central place. When the equipment rooms are in two/more
parts then each part should have one.
3. Portable Extinguishers One set for each room.
4. Detectors Above and below false ceiling and below floor giving due
consideration to depth of false ceiling/floor.
5. Response Indicator To be provided.
6. Panel gas flooding To be provided for HT panel, main LT panel, main LT distribution
board and essential power panels and other such major panels.

EXTERNAL AREAS
1. Hydrants One at ground floor at each entry to station near staircase/DG room.
2. Two/four way fire brigade inlet To be provided for each riser/sprinlder riser.
3. Fire brigade Draw-off connection To be provided on water tank,

6.5 Business Buildings (Group E) 6.5.2.1 Occupancy sub-division E-1 (except oflice
6.5.1 In addition to the general requirements specified buildings)
in 3.4 for type of construction and occupancy group
Details of Fire Detectio@Minguishing
and the exit requirements given in 4, the requirements
Occupancy System
given in 6.5.2 to 6.5.5 shall be complied with.
6.5.2 Fire Detection/Extinguishing System E-1 Automatic fwe alarm system {good
practice [4(17)] and [4(18)], and
The requirements for occupancy sub-divisions as
Table 23}.
specified in Table 23 and Annex C (for High Rise
Buildings) shall apply.

56 NATIONAL BUILDING CODE OF INDIA


6.5.2.2 Occupancy sub-division E-2 6.5.3 Exit Facilities

Details of Fire Detection/Extinguishing 6.5.3.1 In the case of mezzanines or balconies open


Occupancy System to the floor below, or other unprotected vertical
openings between floors, the population of the
a) Laboratory Fixed automatic COZ fire
mezzanine or other subsidiary floor for level shall be
with delicate extinguishing system or
instruments automatic fm alarm system added to that of the main floor for the purpose of
{good practice [4(18)] and determining the required exits, provided, however, that
[4(19)], and Table 23} in no case shall the total number of exit units be less
than that required if all vertic@ openings were enclosed.
b) Solvent storage Automatic foam installation
and/or flammable or automatic C02 fue 6.5.3.2 Not less than two exits shall be provided for
licmid extinguishing system every floor, including basements occupied for office
purposes or uses incidental thereto.
6.5.2.3 Occupancy sub-division E-3
6.5.4 Additional Requirements
Details of Fire Detection/Extinguishing
6.5.4.1 The handling and use of gasoline, fuel oil and
Occupancy System
other flammable liquids shall not be permitted, unless
a) Area of computer Automatic fm alarm system such use and handling complies with the appropriate
installations {good practice [4(18)] and regulations.
[4(19)], and Table 23} any
suitable halon alternative fwe 6.5.4.2 Every boiler room or room containing a central
extinguishing system (see heating plant using solid or liquid fuel shall be
5.3) or any other suitable fme separated from the rest of the building by a separating
extinguishing installation wall. Every boiler room or room containing a central
{see also [4(29)]}. heating plant, which burns gas as a fuel shall be
b) Space under false Automatic fwe alarm system adequately separated from the rest of the building.
ceiling (floor) {good practice [4(18)] and 6.5.5 Exception and Deviation
[4(19)], and Table 23}
6.5.5.1 Basements used only for storage, heating, any
c) Space above false Automatic fwe alarm system
ceiling and below {good practice [4(18)] and other service equipment shall conform to exit
false floor [4(19)], and Table 23} requirements for Group H occupancies in all respects.

d) Electrical switch Automatic fme alarm system 6.6 Requirements of Mercantile Buildings
board {good practice [4(18)] and (Group F)
[4(19)], - and Table 23} and
COZ fire extinguishing 6.6.1 In addition to the general requirements specified
installation in 3.4 for type of construction and occupancy and the
exit requirements given in 4, the requirements given
6.5.2.4 Occupancy sub-division E-4 in 6.6.1.1 to 6.6.5 shall be complied with.

Details of Fire Detectio~xtinguishing 6.6.1.1 Mixed occupancy


Occupancy System No dwelling unit shall have its sole means of exit
Telephone exchanges Any suitable halon through any mercantile occupancy in the same building
alternative fire extinguishing except in the case of a single family unit where the
system (see 5.3) and/or family operates the store.
automatic sprinkler system as
6.6.2 Fire Detectio@xti;guishing System
per requirement (see also
Table 23) The requirements for occupancy sub-divisions F-1 to
F-3 as specified in Table 23 and Annex C (for High
6.5.2.5 Occupancy sub-division E-5 Rise Buildings) shall apply.

Details of Fire Detection/ 6.6.3 Exit Facilities


Occupancy Extinguishing System In addition to the provisions of 4, the following
Broadcasting stations Automatic fire alarm system requirements shall be complied with.
based on smoke detectors
6.6.3.1 In the case of mezzanines or balconies open
and sprinkler system (see
to the floor below, or other un-protected vertical
also Table 23)
openings between floors, the population or area of the

PART 4 FIRE AND LIFE SAFETY 57


mezzanine or other subsidiary floor level shall be added 6.7.3 Exit Facilities
to that of the main floor for the purpose of determining
In addition to the provisions of 4, the following
the required exits, provided, however, that in no case
requirements shall be complied with.
shall the total number of exit units be less than that
required if all vertical openings were enclosed. 6.7.3.1 Not less than two exits shall be provided for
every floor or section, including basements used for
6.6.3.2 At least two separate exits shall be accessible
industrial purposes or uses incidental thereto.
from every part of every floor, including basements;
such exits shall be as remote from each other as 6.7.3.2 In buildings used for aircraft assembly or other
practicable and so arranged as to be reached by occupancy requiring undivided floor areas so large that
different paths of travel in different directions, except the distances from points within the area to the nearest
that a common path of travel maybe permitted for the outside walls where exit doors could be provided are
first 15 m from any point. in excess of 45 m, requirements for distance to exits
may be satisfied by providing stairs leading to exit
6.6.4 Additional Precautions tunnels or to overhead passageways. In cases where
6.6.4.1 Requirements specified in 6.5.4.1 shall be such arrangements are not practicable, the Authority
applicable to all Group F occupancies also. may, by special ruling, permit other exit arrangements
for one storey buildings with distances in excess of
6.6.4.2 Hazardous areas of mercantile occupancies the maximum distances specified in 4, if completely
shall be segregated or protected suitably. automatic sprinkler protection is provided and if the
6.6.4.3 In self-service stores, no check-out stand or heights of ceiling curtain boards and roof ventilation
associated railings or barriers shall obstruct exits or are such as to minimize the possibility that employees 1.
b--

required aisles or approaches thereto. will be overtaken by the spread of fire or smoke within
1800 mm of the floor level before they have time to
6.6.4.4 Open-air mercantile operations, such as open- reach exits, provided, however, that in no case may
air markets, gasoline filling stations, roadside stands the distance of travel to reach the nearest exit exceed
for the sale of a farm produce and other outdoor 45 m where smoke venting is required as a condition
mercantile operations shall be so arranged and for permitting distances of travel to exits in excess of
conducted as to maintain free and unobstructed ways the maximum otherwise allowed.
of travel at all times to permit prompt escape from any
point of danger in case of fire or other emergency, but 6.7.3.3 Additional precautions
no dead-ends in which persons might be trapped due a) In any room in which volatile flammable
to display stands, adjoining buildings, fences, vehicles substances are used or stored, no device
or other obstructions. generating aglow or flame capable of igniting
flammable vapour shall be installed or used.
6.6.4.5 If mercantile operations are conducted in
Such a room shall be provided with a suitably
roofed-over areas, these shall be treated as mercantile
designed exhaust ventilation system (see
buildings, provided canopies over individual small
Annex D). To ensure safety from fire due to
stands to protect merchandise from the weather shall
short circuit, faulty electrical connection or
not be constructed to constitute buildings for the
some similar cause, proper care shall be taken
purpose of the Code.
in designing electrical installations in such
6.6.5 Exception and Deviation room (see Part 8 ‘Building Services, Section 2
Electrical Installations’).
Any mercantile occupancy, where goods of a highly
hazardous nature are pre-dominant, shall be considered b) The storage, use and handling of gasoline,
under Group J occupancy for the purpose of the Code. fuel oil and othqr flammable liquids shall
not be permibed’ in any Group G occupancy
6.7 Requirements of Industrial Buildings (Group G) unless it complies with regulations
pertaining to Petroleum Act, 1934 and Rules
6.7.1 In addition to the general requirements specified
thereunder.
in 3.4 for the type of construction and occupancy group
c) Every boiler room or room below the first
and the exit requirements given in 4, the requirements
floor containing a heating plant shall be
given in 6.7.2 to 6.7.5 shall be complied with.
adequately separated from the rest of the
6.7.2 Fire Detection/Extinguishing System buildings.
The requirements for occupancy sub-divisions G-1 to d) For requirements regarding electrical
G-3 as specified in Table 23 and Annex C (for High generating and distribution stations, reference
Rise Buildings) shall apply. may be made to good practice [4(23)].

58 NATIONAL BUILDING CODE OF INDIA


6.7.3.4 Exception and deviation 5) Industrial buildings of high hazard are
permitted only up to 15 m height.
a) Basements used only for storage, heating or
other service equipment, and not subject to 6.7.4 For detailed information on fire safety of certain
industrial occupancy, shall have exits in individual (specific) industrial occupancies reference
accordance with the requirements of Group may be made to good practice [4(39)].
H occupancies.
6.7.5 Fire protection considerations for venting
b) The following exceptions shall apply to industrial occupancies shall be as given in Annex D.
special purpose industrial occupancies:
1) Exits need be provided only for the 6.8 Requirements of Storage Buildings (Group H)
persons actually employed; spaces not
6.8.1 In addition to the general requirements
subject to human occupancy because of
specified in 3.4 for type of construction and
the presence of machinery or equipment
occupancy group and the exit requirements given in 4,
may be excluded from consideration.
the requirements given in 6.8.2 to 6.8.5 shall be
2) Where unprotected vertical openings are complied with.
necessary to manufacturing operations,
these may be permitted beyond the limits 6.8.2 Fire Detection/Extinguishing System
specified for industrial occupancy, The requirements for occupancy group H, as specified
provided every floor level has direct in Table 23 and Annex C (for High Rise Building)
access to one or more enclosed stairways shall apply.
or other exits protected against obstruction
NOTE — Automatic sprinklers are prohibited where water
by any fire in the open areas connected
reactive materiafs are kept. Instead automatic tire alarm system
by the unprotected vertical openings or coupled with suitable fire extinguishing systems shall be
smoke therefrom. installed.

3) Industrial buildings of low and moderate 6.8.3 Exit Facilities


hazard are permitted only up to 18 m
height. In addition to the provisions of 4, the following
requirements shall also be complied with.
c) The following exceptions shall apply to high
hazard industrial occupancies: 6.8.3.1 Every building or structure used for storage
1) Exits shall be so located that it will not and every section thereof considered separately, shall
be necessary to travel more than 22.5 m have access to at least one exit so arranged and located
from any point to reach the nearest exit. as to provide a suitable means of escape for any person
2) From every point in every floor area, employed therein and in any room or space exceeding
there shall beat least two exits accessible 1400 m2 gross area, or where more than 10 persons
in different directions; where floor areas may be normally present, at least two separate means
are divided into rooms, there shall be at of exit shall be available, as remote from each other as
least two ways of escape from every practicable.
room, however small, except toilet 6.8.3.2 Every storage area shall have access to at least
rooms, so located that the points of access two means of exit, which can be readily opened. This
thereto are out of or suitably shielded shall not be subject to locking so long as any persons
from areas of high hazard. are inside and shall not depend on power operation.
3) In addition to types of exits for upper
6.8.3.3 The following special provisions shall apply
floors specified for Group G occupancies,
to parking garages of closed or open type, above or
slide escapes may be used as required
below ground, but not to mechanical parking facilities
exits for both new and existing
where automobiles are moved into and out of storage
buildings.
mechanically which are not normally occupied by
4) All high hazard industrial occupancies
persons and thus require no exit facilities. Where repair
shall have automatic sprinkler protection
operations are conducted, the exits shall comply with
or such other protection as may be
the requirements of Group G occupancies in addition
appropriate to the particular hazard,
to compliance with the following:
including explosion venting for any area
subject to explosion hazard, designed to a) Where both parking and repair operations are
minimize danger to occupants in case of conducted in the same building, the entire
fiie or other emergency before they have building shall comply with the requirements
time to utilize exits to escape. for Group G occupancies, unless the parking

PART 4 FIRE AND LIFE SAFETY 59


T-

and repair sections are effectively separated the grade is one storey or more lower at the
by separation walls. rear than at the street).
b) Every floor of every closed parking garage
6.8.3.4 Exits from aircraft hangers (storage or
shall have access to at least two separate servicing areas) shall be provided at intervals of not
means of exit, so arranged that from any point more than 45 m on all exterior walls of aircraft hangers.
in the garage the paths of travel to the two There shall be a minimum of two exits serving each
means of exit shall be in different directions,
aircraft storage or servicing areas. Horizontal exits
except that a common path of travel may be through interior fire walls shall be provided at intervals
permitted for the first 15 m, from any point. of not more than 30 m. ‘Dwarf or ‘smash’ doors
c) On the street floor, at least two separate exit accommodating aircraft may be used to comply with
doors shall be provided, except that any these requirements. All doors designated as exits shall
opening for the passage of automobiles may be kept unlocked in the direction of exit travel while
serve as a means of exit, provided no door or the area is occupied.
shutter is installed thereon. Street floor exits
in closed garages shall be so arranged that no 6.?3.3.5 Exits from mezzanine floors in aircraft storage
point in the area is more than 30 m from the or servicing areas shall be so arranged that the
nearest exit, or 45 m in the case of garages maximum travel to reach the nearest exits from any
protected by automatic sprinklers, distance point on the mezzanine shall not exceed 22.5 m. Such
being measured along the natural path of exits shall lead directly to a properly enclosed stairwell
travel. discharging directly to the exterior or to a suitably cut-
off area or to outside fire escape stairs.
d) On floors above the street, at least two means
..-
of exit shall be provided, one of which shall 6.8.3.6 The following special provisions shall apply
be an enclosed stairway. The other means of to grain elevators:
egress may be a second exit of any of the
a) There shrdl be at least one stair tower from
types, or in a ramp type garage with open
basement to first floor and from the fmt floor
ramps not subject to closure, the ramp may
to the top floor of workhouse which is enclosed
serve as the second means of exit.
in a dust-tight non-combustible shaft.
e) Upper floor exits in closed garages shall be
b) Non-combustible doors of self-closing type
so arranged that no point in the area shall be
shall be provided at each floor landing.
more than 30 m from the nearest exit other
than a ramp on the same floor level or 45 m c) An exterior fire escape of the stair or basket
in the case of garages protected by automatic ladder type shall be provided from the roof
sprinklers. of the workshop to ground level or the roof
of an adjoining annexe with access from all
f) On floors below the street (either basement
floors above the f~st.
or outside underground garages) at least two
exits shall be provided, not counting any d) An exterior fire escape of either the stair or
automobile ramps, except that for garages basket ladder type shrdl be provided from the
extending only one floor level below the roof of each storage annexe to ground level.
street, a ramp leading direct to the outside may 6.8.4 Additional Precautions
constitute one required means of exit. In
garages below street level, exits shall be so Requirements specified in 6.7.3.3 shall apply to Group
arranged that no part of the area shall be more H occupancies also.
than 30 m from the nearest stair exit.
6.8.5 Exceptions and Deviations
g) If any gasoline pumps are located within any
closed parking garage, exits shall be so Every -area used for the’ storage of hazardous
located that travel away from the gasoline commodities shall have an exit within 22.5 m of any
pump in any direction shall lead to an exit; point in the area where persons maybe present or 35 m
with no dead-end in which occupants might where automatic sprinkler protection is provided.
be trapped by fire or explosion at any
6.9 Requirements of Buildings for Hazardous Uses
gasoline pump. Such exit shall lead to the
(Group J)
outside on the building on the same level, or
downstairs; no upward travel shall be 6.9.1 In addition to the general requirements specified
permitted unless direct outside exits are in 3.4 for type of construction and occupancy group
available from that floor and any floor below and the exit requirements given in 4, the requirements .i
(as in the case of a basement garage where given in 6.9.2 to 6.9.4 shall be complied with.

60 NATIONAL BUILDING CODE OF INDIA


6.9.2 Fire Detection/Extinguishing System or permitted unless it is enclosed in a
flameproof enclosure.
The requirements for occupancy Group J, as specified
in Table 23 and Annex C (for High Rise Building) d) The use, handling, storage and sale of
shall apply. gasoline, fuel oil and other flammable liquids
snail not be permitted in Group J occupancies
NOTE — Hazardous buildings shall have vapour detectors/
unless such use, handling, storage and sale is
explosion suppression systems/automatic sprinklers, besides
hydrant system, wet risers and automatic fire alarm system
in accordance with appropriate legislation in
depending on the type of fire hazard involved. force.
e) All openings in exterior walls except wall
6.9.3 Exit Facilities
vents shall be protected by a fire stop
Requirements specified in 4 and 6.7.3.4 (c) shall apply assembly as in 4 and they shall be fixed,
to Group J occupancies also. automatic or self-closing. Wall vents having
an area of not less than 100 cmz each shall be
6.9.4 Additional Precautions placed in the exterior walls near the floor line,
not more than 1 800 mm apart horizontally.
The following requirements shall apply to all Group J
Each building shall be provided with a power
occupancies, as applicable:
driven fan exhaust system of ventilation
a) Each building where gas is employed for any which shall be arranged and operated so as to
purpose shall be provided with an approved produce a complete change of air in each room
outside gas shut-off valve conspicuously every 3 min.
marked. The detailed requirements regarding f) Each machine in dry-cleaning establishments
safe use of gas shall be as specified in which uses flammable liquid shall have an
Part 9 ‘Plumbing Services, Section 2 Gas adequate steam line or any other suitable
supply’. extinguishing agent directly connected to it,
b) Each boiler room or room containing a so arranged as to have the agent automatically
heating plant shall be separated from the rest released to the inside of each machine should
of the building by a separating wall. an explosion occur in the machine.
c) In any room in which volatile flammable Q Equipment or machinery which generates or
substances are used or stored, no device emits combustible or explosive dust or fibres
generating a spark, or glow flame capable of shall be provided with an adequate dust
igniting flammable vapour shall be installed collecting and exhaust system.

PART 4 FIRE AND LIFE SAFETY


ANNEX B

(Clauses 3.1.8 and 3.1.1 1)


BROAD CLASSIFICATION OF INDUSTRIAL AND NON-INDUSTRLAL OCCUPANCIES
INTO DIFFERENT DEGREE OF HAZARD

B-1 LOW HAZARD OCCUPANCIES Office premises


Places of worship
Abrasive manufacturing premises
Pottery works
Aerated water factories
Poultry farms
Agarbatti manufacturing premises
Residential buildings (A-1 to A-4) (except hotels A-5)
Analytical and/or Q.C. Laboratories
Salt crushing factories/refineries stables
Arecanut slicing and/or Betelnut factories
Sugar candy manufacturing
Asbestos steam packing and lagging manufacturers
Sugar factories and refineries
Assembly buildings small (D-4 and D-5)
Tanneries
Battery charging and service stations
Umbrella assembling factories
Battery manufacturing
Vermicelli factories
Breweries
Water treatment/filtration plants and water pump houses
Brickwork
Zinc/copper factories
Canning factories
Cardamom factories B-2 MODERATE HAZARD OCCUPANCIES
Cement factories and/or asbestos or concrete products Airport and other transportation terminal buildings
manufacturing premises Aluminium factories
Ceramic factories, crockery, stoneware pipe Assembly buildings (D-1 to D-3)
manufacturing g
Atta and cereal grinding
Clay works
Bakeries and biscuit factories
Clock and watch manufacturing
Beedi factories
Clubs
Bobbin factories
Coffee curing, roasting and grinding factories
Book-binders, envelopes and paper bag manufacturing
Condensed milk factories, milk pasturising plants and Cable manufacturing
dairies
Camphor boiling
Confectionery manufacturing
Candle works
Dwellings, lodges, dormitories, etc
Carbon paper/typewriter ribbon makers
Educational and research institutions
Card board box manufacturing
Electric lamps (incandescent and fluorescent) and T.V.
Carpenters, wood wool anti furniture makers
tube manufacturing
Carpet and durries factories
Electroplating works
Cashewnut factories
Engineering workshops
Chemical manufacturers (us-hg raw materials having
Fruits and vegetables dehydrating and drying factories
F.P > 23°C)
Fruits products and condiment factories
Cigar and cigarette factories
Glass and glass fibre manufacturing
Coir factories
Godowns and warehouses (non-combustible goods) Cold storage premises
Gold thread/gilding factories Computer installations
Gum and/or glue and gelatine manufacturing Cork products manufacturing (coir, carpets, rugs and
Ice candy and ice-cream and ice factories tobacco) (hides and skin presses)
Ink (excluding printing ink) factories Dry cleaning, dyeing and laundries
Mica products manufacturing Electric sub-stations/distribution stations

PART 4 FIRE AND LIFE SAFETY 63


Electrical generating stations except under ground Tobacco chewing and pan masala making
powerhouses Tobacco re-drying factories
Enamelware factories Woolen mills
Filler and wax paper manufacturing
B-3 HIGH HAZARD OCCUPANCIES
Flour mills
Gment makers A)
Ghee factories (other than vegetable) Aircraft hangers
Godowns and warehouses (other than non-combustible Alurninium/magnesium powder plants
goods) Bitumanized paper/hessian clothhr felt manufacturing
Grains and seed disintegrating or crushing Bulk storage of flammable liquids (tank farm, etc)
Grease manufacturing Celluloid goods making
Hosiery, lace, embroidery and thread Chemical manufacturers (where raw materials have a
Hospitals including ‘X’ -ray and other diagonastic F.P. < 23°C)
clinics (institutional buildings) Cigarette filter manufacturing
Incandescent gas mantle manufacturers Cinema films and T.V. production studios
Industrial gas manufacturing (only halogenated Coal, coke and charcoal ball and briquettes making
hydrocarbonslinert gases)
Collieries, steel plants
Man-made yarn/fibre (except acrylic fibre/yarn)
Cotton seeds cleaning and delinting factories
Manure and fertilizer works (blending, mixing and
Cotton waste factories
granulating only)
Distilleries
Mercantile occupancies (departmental stores, shopping
complex, etc) Duplicatinglstencil paper making
Fire works manufacture
Mineral oil blending and processing
Foamed plastic and/or converting plants
Museums, archieves, record rooms
Godowns of warehouses (combustible/hazardous
Oil and leather cloth factories
goods) (H)
Open storage of flammable liquids (in drums, cans, etc)
Grass, hay, fpdder and BHOOSA (chaff)
Oxygen plants
Hazardous occupancy buildings (J)
Paper and cardboard mills (except raw material yard)
Industrial gas manufacturing (except halogenated
Piers, wharves, dockyards hydrocarbon gases/inert gases)
Plastic goods manufacturing Industrial units (G-3 occupancies)
Ply woodfwood veneering factories Jute mills and jute presses
Printing press premises Linoleum factories
Pulverizing and crushing mills Man-made fibres (only acrylic fibre/yarn making)
Residential apartments, hotels, cafes, restaurants Match factories
Rice mills Mattress and pillow m#cings (foam plastics)
Rope works Metal or tin printers (if more than 50 percent is
Rubber goods manufacturing engineering, shift to ozdinary hazard)
Rubber tyres and tubes manufacturing Oil mills
Sheliac factories Oil extraction plants
Silk filiatures Oil terrninals/depots
Soaps and glycerine factories Paints/Varnish factories
Spray painting Paper and cardboard mills (only raw material yard)

Starch factories Pressing factories


Tea factories (including blending packing of tea) Printing ink making

Telephone exchanges, garages Resin, lamp black and turpentine manufacture

Textile mills Saw mills

64 NATIONAL BUILDING CODE OF INDIA


Surgical cotton manufacturing Explosive factories
Tarpaulin and canvas proofing factories LPG bottling plants
Turpentine and resin distilleries Petrochemical plants
Tyre retreading and resolving factories Petroleum refineries
Underground shopping complexes (F-3) NOTE — In case of complexes having segregated plants with
varying degrees of hazards, the competent authority having
B)
jmisdictions shall be consulted to decide the level of protections
Ammonia and urea synthesis plants to be provided.

ANNEX C

(Clauses 3.4.11.1,4.18.2,5.1.8, 5.2.2,6.1.2,6.2.3,6.3.2, 6.4.3,6.5.2,6.6.2,


6.7.2,6.8.2 and 6.9.2)
FIRE PROTECTION REQUIREMENTS FOR HIGH RISE BUILDINGS —
15 m IN HEIGHT OR ABOVE

C-O GENERAL on top of the shaft and separated from the shaft
by the floor of the room.
In addition to the general provisions given in this Part,
c) Landing doors in lift enclosures shall have a
the Authority may insist on suitable protection
fire resistance of not less than 1 h.
measures (see C-1 to C-n) in a building 15 m in height
or above. d) The number of lifts in one row for a lift bank
shall not exceed 4 and the total number of
C-1 CONSTRUCTION lifts in the bank (of two rows) shall not exceed
8. A wall of 2 h fire rating shall separate
C-1.l All materials of constructions in load bearing
individual shafts in a bank.
elements, stairways and corridors and facades shall be
non-combustible. e) Lift car door shall have a fiie resistance rating
of half an hour.
C-1.2 The interior finish materials shall not have aflame Collapsible gates shall not be permitted for
f)
spreadability rating exceeding Class 1 (see 3.4.15.2). lifts and shall have solid doors with fire
C-1.3 The internal walls or staircase shall be of brick resistance of at least 1 h.
or reinforced concrete with a minimum of 2 h fire g) If the lift shaft and lobby is in the core of the
rating. building, a positive pressure between 25 and
30 Pa shall be maintained in the lobby and a
C-1.4 The staircase shall be ventilated to the
positive pressure of 50 Pa shall be maintained
atmosphere at each landing and a vent at the top; the
in the lift shaft. The mechanism for
vent openings shall be of 0.5 mz in the external wall
pressurization shall act automatically with the
and the top. If the staircase cannot be ventilated,
fire alarm; it shall be possible to operate this
because of location or other reasons, a positive pressure
mechanically also.
50 Pa shall be maintained inside. The mechanism for
pressurizing the staircase shall operate automatically h) Exit from the lift lobby, if located in the
with the fire alarm. The roof of the shaft shall be 1 m core of the building, shall be through a self-
above the surrounding roof. Glazing or glass bricks if closing smoke stop door of half an hour fire
used in staircase, shall have fire resistance rating of resistance.
minimum 2 h. j) Lifts shall not normally communicate with
the basement; if, however, lifts are in
C-1.5 Lifts communication, the lift lobby of the
basements shall be pressurized as in (g), with
General requirements of lifts shall be as follows:
self-closing door as in (h).
a) Walls of lift enclosures shall have a fire rating k) Grounding switch, at ground floor level,
of 2 h; lifts shafts shall have a vent at the top shall be provided on all the lifts to enable the
of area not less than 0.2 mz. fire service to ground the lifts.
b) Lift motor room shall be located preferably m) Telephone or other communication facilities

PART 4 FIRE AND LIFE SAFETY 65


shall be provided in lift cars for building of the entrance level. When the switch is on,
30 m in height and above. Communication landing call-points will become
system for lifts shall be connected to fire inoperative and the lift will be on car
control room for the building. control only or on a priority control
n) Suitable arrangements such as providing slope device. When the switch is off, the lift
in the floor of lift lobby, shall be made to will return to normal working. This lift
prevent water used during fire fighting, etc, can be used by the occupants in normal
at any landing from entering the lift shafts. times.
p) A sign shall be posted and maintained on 7) The words ‘Fire Lift’ shall be
every floor at or near the lift indicating that conspicuously displayed in fluorescent
in case of fke, occupants shall use the stairs paint on the lift landing doors at each
unless instructed otherwise. The sign shall floor level.
also contain a plan for each floor showing the 8) The speed of the fire lift shall be such
locations of the stairways. that it can reach the top floor from ground
Alternate source of power supply shall be level within 1 min.
provided for all the lifts through a manually C-1.6 Basements
operated changeover switch.
C-1.6.1 Each basement shall be separately ventilated.
q) Fire Li$ts — Following details shall apply for
Vents with cross-sectional area (aggregate) not less
a fire lift:
than 2.5 percent of the floor area spread evenly round
1) To enable fire services personnel to reach
the perimeter of the basement shall be provided in the
the upper floors with the minimum delay,
form of grills, or breakable stallboard lights or
one fire lift per 1200 mz of floor area
pavement lights or by way of shatls. Alternatively, a
shall be provided and shall be available
system of air inlets shall be provided at basement floor
for the exclusive use of the firemen in an
level and smoke outlets at basement ceiling level. Inlets
emergency.
and extracts may be terminated at ground level with
2) The lift shall have a floor area of not less stallboa-d or pavement lights as before, but ducts to
than 1.4 m2. It shall have loading capacity convey fresh air to the basement floor level have to be
of not less than 545 kg (8 persons lift) laid. Stallboard and pavement lights should be in
with automatic closing doors of positions easily accessible to the fire brigade and
minimum 0.8 m width, clearly marked ‘SMOKE OUTLET’ or ‘AIR INLET’
3) The electric supply shall be on a separate with an indication of area served at or near the opening.
service from electric supply mains in a
C-1.6.2 The staircase of basements shall be of
building and the cables run in a route safe
enclosed type having fire resistance of not less than
from fire, that is, within the lift shaft.
2 h and shall be situated at the periphery of the
Lights and fans in the elevators having
basement to be entered at ground level only from the
wooden paneling or sheet steel
open air and in such positions that smoke from any
construction shall be operated on 24 V
fire in the basement shall not obstruct any exit serving
supply.
the ground and upper stores of the building and shall
4) Fire fighting lift should be provided with
communicate with basement through a lobby provided
a ceiling hatch for use in case of
with fire resisting self closing doors of 1 h resistance.
emergency, so that when the car gets
For travel distance see 4.5. If the travel distance exceeds
stuck up, it shall be easily openable.
as given in Table 21, additional staircases shall be
5) In case of failure of normal electric provided at proper places.
supply, it shall automatically trip over to
alternate supply. For apartment houses, C-1.6.3 In multi-storey basements, intake ducts may
this changeover of supply could be done serve all basement levels, but each basement levels
through manually operated changeover and basement compartment shall have separate smoke
switch. Alternatively, the lift shall be so outlet duct or ducts. Ducts so provided shall have the
wired that in case of power failure, it same fire resistance rating as the compartment itself.
comes down at the ground level and Fire rating may be taken as the required smoke
comes to stand-still with door open. extraction time for smoke extraction ducts.
6) The operation of a fire lift is by a simple C-1.6.4 Mechanical extractors for smoke venting
toggle or two-button switch situated in a system from lower basement levels shall also be
glass-fronted box adjacent to the lift at provided. The system shall be of such design as to

66 NATIONALBUILDING CODE OF INDIA


operate on actuation of heathmoke sensitive detectors from all floors. On large area floors several such pipes
or sprinklers, if installed, and shall have a considerably may be necessary which should be spaced 30 m apart.
superior performance compared to the standard units. Care shall be taken to ensure that the construction of
It shall also have an arrangement to start it manually. the drain pipe does not allow spread of fue/smoke from
floor to floor.
C-1.6.4.1 Mechanical extractors shall have an internal
locking arrangement, so that extractors shall continue C-1.9 Service Ducts/Shafta
to operate and supply fans shall stop automatically with
the actuation of fwe detectors. a) Service ducts and shafts shall be enclosed by
walls of 2 h and doors of 1 h, fue rating. All
C-1.6.4.2 Mechanical extractors shall be designed to such ducts/shafts shall be properly sealed and
permit 30 air changes per hour in case of fire or distress fire stopped at all floor levels.
call. However, for normal operation, air changes
b) A vent opening at the top of the service shaft
schedule shall be as given in 3.4.11.5.
shall be provided having between one-fourth
C-1.6.4.3 Mechanical extractors shall have an and one-half of the area of the shaft.
alternative source of supply,
C-1.1O Refuse chutes shall have opening at least 1 m
C-1.6.4.4 Ventilating ducts shall be integrated with above roof level or venting purpose and they shall have
the structure and made out of brick masonry or an enclosure wall of non-combustible material with
reinforced cement concrete as far as possible and when fire resistance of not less than 2 h. They shall not be
this duct crosses the transformer area or electrical located within the staircase enclosure or service shafts,
switchboard, fire dampers shall be provided. or air-conditioning shafts inspection panel and doors
shall be tight fitting with 1 h fwe resistance; the chutes
C-1.6.5 Use of basements for kitchens working on gas
h should be as far away as possible from exits.
fuel shall not be permitted, unless air conditioned.

The basement shall not be permitted below the ward block C-1.11 Refuge Area
of a hospitdhnu-sing home unless it is fully sprinkled. Provisions contained in 4.12.3 shall apply for all
buildings except multi-family dwellings, refuge area
Building services such as electrical sub-stations, boiler
rooms in basements shall comply with the provisions of not less than 15 m2 shall be provided on the external
walls.
of the Indian Electricity Act/Rules.
C-1.12 Electrical services shall conform to the
C-1.6.6 If cut outs are provided from basements to
following:
the upper floors or to the atmospheres, all sides cut
out openings in the basements shall be protected by a) The electric distribution cables/wiring shall
sprinkler head at close spacing so as to form a water be laid in a separate duct. The duct shall be
curtain in the event of a fire. sealed at every floor with non-combustible
materials having the same fwe resistance as
C-1.7 Openable windows on external walls shall be
that of the duct. Low and medium voltage
fitted with such locks that can be opened by a fireman’s
wiring running in shaft and in false ceiling
axe.
shrdl run in separate conduits;
C-1.8 All floors shall be compartmented with area not b) Water mains, telephone lines, intercom lines,
exceeding 750 m2 by a separation wall with 2 h fire gaspipes or any other service line shrdl not be
rating, for floors with sprinklers the area may be laid in the duct for electrical cables; use of
increased by 50 percent. In long building, the fire bus ducts/solid rising mains instead of cables
separation walls shall be at distances not exceeding is preferred;
40 m. For departmental stores, shopping centres and
c) Separate circuits for f~e fighting pumps, lifts,
basements, the area may be reduced to 500 m2 for
staircases and corridor lighting and blowers
compartmentation. Where this is not possible, the
for pressurizing system shall be provided
spacings of the sprinklers shall be suitably reduced.
directly from the main switch gear panel and
When reducing the spacing of sprinklers, care should
these circuits shall be laid in separate conduit
be taken to prevent spray from one sprinkler impeding
pipes, so that fue in one circuit will not affect
the performance of an adjascent sprinkler head.
the others. Such circuits shall be protected at
C-1.8.1 It is essential to make provisions for drainage origin by an automatic circuit breaker with
of any such water on all floors to prevent or minimize its no-volt coil removed. Master switches
water damage of the contents. The drain pipes should controlling essential service circuits shall be
be provided on the external wall for drainage of water clearly labelled;

PART 4 FIRE AND LIFE SAFETY 67


d) The inspection panel doors and any other b) All wiring in fume hoods shall be of fibre
opening in the shaft shall be provided with glass insulation. Thermal detectors shall be
ah--tight fire doors having fire resistance of installed into fume hoods of large kitchens
not less than2h; for hotels, hospitals, and similar areas located
e) Medium and low voltage wiring running in in high rise buildings. Arrangements shall be
shafts, and within false ceiling shall run in made for automatic tripping of the exhaust
metal conduit. Any 230 V wiring for lighting fan in case of fire. If LPG is used, the same
or other services, above false ceiling, shall shall be shut off. The voltage shall be 24 V or
have 660 V grade insulation. The false ceiling, 100 V dc operated with external rectifier. The
including all iixtures used for its suspension, valve shall be of the hand re-set type and shall
shall be of non-combustible material and shall be located in an area segregated from cooking
provide adequate fire resistance to the ceding ranges. Valves shall be easily accessible. The
in order to prevent spread of fire across ceiling hood shall have manual facility for steam or
reference may be made to good practice carbon dioxide gas injection, depending on
[4(29)]; duty condition; and
f) An independent and well ventilated service c) Gas meters shall be housed in a suitably
room shall be provided on the ground level or constructed metal cupboard located in a well
first basement with direct access from outside ventilated space, keeping in view the fact that
or from the corridor for the purpose of LPG is heavier than air and town gas is lighter
termination of electric supply from the than air.
licensees’ service and alternative supply cables.
C-1.14 Rumination of Means of Exit
The doors provided for the service room shall
have fire resistance of not less than 2 h; Staircase and corridor lights shall conform to the
NOTE — If service room is located at the first basement,
following (see 4.16 and 4.17 for additional details):
it should have automatic fire extinguishing system. a) The staircase and corridor lighting shall be
!3) If the licensees agree to provide meters on on separate circuits and shall be independently
upper floors, the licensees’ cables shall be connected so as it could be operated by one
segregated from consumers’ cables by switch installation on the ground floor easily
providing a partition in the duct. Meter rooms accessible to fire fighting staff at any time
on upper floors shall not open into stair case irrespective of the position of the individual
enclosures and shall be ventilated directly to control of the light points, if any. It should be
open air outside; and of miniature circuit breaker type of switch so
h) Suitable circuit breakers shall be provided at as to avoid replacement of fuse in case of
the appropriate points. crisis;
b) Staircase and corridor lighting shall also be
C-1.13 Gas supply shall conform to the following:
connected to alternative supply. The
a) Town Gas/L.P. Gas Supply Pipes — Where alternative source of supply maybe provided
gas pipes are run in buildings, the same shall by battery continuously trickle charged from
be run in separate shafts exclusively for this the electric mains;
purpose and these shall be on external walls, c) Suitable arrangements shall be made by
away from the staircases. There shall no installing double’throw switches to ensure that
interconnection of this shtit with the rest of the lighting installed in the staircase and the
the floors. LPG distribution pipes shall always corridor does notget connected to two sources
be below the false ceiling. The length of these of supply simu~faneously. Double throw
pipes shall be as short as possible. In the case switch shall be installed in the service room
of kitchen cooking range area, apart from for terminating the stand-by supply;
providing hood, covering the entire cooking
d) Emergency lights shall be provided in the
range, the exhaust system should be designed
staircase and corndo~ and
to take care of 30 m3 per minute per m2 of
e) All wires and other accessories used for
hood protected area. It should have grease
emergency light shall have fire retardant
filters using metallic grill to trap oil vapours
property.
escaping into the fume hood.
NOTE — For detailed information on gas pipe C-1.15 A stand-bv electric generator shall be installed
installations, reference may be made to Part 9 ‘Plumbing to supply power to staircase and corridor lighting
Services, Section 3 Gas Supply’. circuits, fue lifts, the stand-by fue pump, pressurization

68 NATIONAL BUILDING CODE OF INDIA


fans and blowers, smoke extraction and damper ceiling and its fixtures shall be of non-
systems in case of failure of normal electric supply. combustible material.
The generator shall be capable of taking starting current @ The materials used for insulating the duct
of all the machines and circuits stated above system (inside or outside) shall be of non-
simultaneously. If the stand-by pump is driven by diesel combustible materials. Glass wool shall not
engine, the generator supply need not be connected to be wrapped or secured by any material of
the stand-by pump. Where parallel HV/LV supply from combustible nature.
a separate sub-station is provided with appropriate h) Area more than 750 mz on individual floor
transformer for emergency, the provision of generator shall be segregated by a fire wall and
may be waived in consultation with the Authority. automatic fire dampers for isolation shall be
C-1.16 Transformers shall conform to the following: provided [see (j)].

a) A sub-station or a switch-station with oil filled j) Air ducts serving main floor areas, corridors,
equipment shall not be located in the building. etc, shall not pass through the staircase
The sub-station structure shall have separate enclosure.
fire resisting walls/surroundings and shall k) The air-handling units shall be separate for
necessarily be located at the periphery of the each floor and air ducts for every floor shall
floor having separate access from fire escape be separated and in no way inter-connected
stair case. The outside walls, ceiling, floor, with the ducting of any other floor.
openings including doors and windows to the m) If the air-handling unit serves more than one
sub-station area shall be provided with a fire floor, the recommendations given above shall
resisting door of 2 h fire rating. Direct access be complied within addition to the conditions
to the transformer room shall be provided, given below:
preferably from outside fire escape staircase. 1) proper arrangements by way of automatic
b) The sub-station area needs to be maintained at fire dampers working on smoke detector/
negative air pressures and area in sub-station or fusible link for isolating all ducting at
shall not be used as storage/dump areas. every floor from the main riser shall be
c) When housed inside the building, the made.
transformer shall be of dry type and shall be 2) When the automatic fire alarm operates,
cut off from the other portion of premises by the respective air-handling units of the air-
wallsldoorslcutout having fire resistance conditioning system shall automatically
rating of 4 h. be switched off.

C-1.17 Air-conditioning shall conform to the n) The vertical shaft for treated fresh air shall
following: be of masonry construction.
P) The air filters of the air-handling units shall
a) Escape routes like staircases, common
be of non-combustible materials.
corridors, lift lobbies, etc, shall not be used
q) The air-handling unit room shall not be used
as return air passage.
for storage of any combustible materials.
b) The ducting shall be constructed of substantial
gauge metal in accordance with good practice r) Inspection panels shall be provided in the
[4(31]. main trunking to facilitate the cleaning of
ducts of accumulated dust and to obtain access
c) Wherever the ducts pass through fire walls or
for maintenance of fire dampers.
floors, the opening around the ducts shall be
sealed with materials having fire resistance s) No combustible rrgwerial shall be fixed nearer
rating of the compartment. than 150 mm to &y duct unless such duct is
d) Where duct crosses a compartment which is properly enclosed and protected with non-
fire rated, the ducts shall be fire rated for same combustible material (glass wool or spunglass
fire rating. Further depending on services with neoprene facing enclosed and wrapped
passing around the duct work, which may get with aluminimum sheeting) at least 3.2 mm thick
affected in case of fire temperature rising, the and which would not readily conduct heat.
ducts shall be insulated. t) Fire Dampers
e) As far as possible, metallic ducts shall be used 1) These shall be located in conditioned air
even for the return air instead of space above ducts and return air ducts/passages at the
the false ceiling. following points:
f) Where plenum is used for return air passage, i) At the fwe separation wall.

PART 4 FIRE AND LIFE SAFETY 69


-T--

ii) Where ductslpassages enter the prevent the flow of oil into the boiler room in
central vertical shaft. case of tank rupture.
iii) Where the ducts pass through floors. f) Foam inlets shall be provided on the external
iv) At the inlet of supply air duct and the walls of the building near the ground level to
return air duct of each compartment enable the fire services to use foam in case of
on every floor. fire.
2) The dampers shall operate automatically y
C-2 PROVISION OF FIRST-AID FIRE FIGHTING
and shall simultaneously switch off the
APPLIANCES
air-handling fans. Manual operation
facilities shall also be provided. The first-aid fire fighting equipment shall be provided
NOTE — For blowers, where extraction system on all floors, including basements, lift rooms, etc, in
and duct accumulators are used, dampers shall be accordance with good practice [4(2 1)] in consultation
provided. with the Authority.
3) Fire/smoke dampers (for smoke extraction
shafts) for buildings more than 24 m in C-3 FIRE ALARM SYSTEM
height. C-3.1 All buildings with heights of 15 m or above
For apartment In non-ventilated shall be equipped with manually operated electrical
houses lobbiesl corridors fire alarm (MOEFA) system and automatic fire alarm
operated by fusible system in accordance with good practice [4(18)] and
link/smoke detectors [4(19)]. However, apartment buildings between 15 m
and with manual and 30 m in height may be exempted from the
control. installation of automatic fiie alarm system provided
For other On operation of smoke the local fire brigade is suitably equipped for dealing
buildings detection system and with fire in a building of 15 m in height or above and
with manual control. in the opinion of the Authority, such building does not
constitute a hazard to the safety of the adjacent property
4) .4~tomatic fire dampers shall be so
or occupants of the building itself.
afranged as to close by gravity in the
direction of air movement and to remain C-3.1.1 Manually operated electrical fire alarm system
tightly closed on operation of a fusible shall be installed in a building with one or more call
link/s”moke detector. boxes located at each floor. The call boxes shall
conform to good practice [4(18)] and [4(19)].
C-1.18 Provisions of boiler and boiler rooms shall
conform to Indian Boiler Act. Further, the following C-3.1.2 The installation of call boxes in hostels and
additional aspects may be taken into account in the such other places where these are likely to be misused
location of boiler room: shall as far as possible be avoided. Location of call boxes
in dwelling units shall preferably be inside the building.
a) The boilers shall not be allowed in sub-
basement, but may be allowed in the C-4 LIGHTNING PROTECTION OF BUILDINGS
basements away from the escape routes.
The lightning protection for buildings shall be provided
b) The boilers shall be installed in a fire resisting
as given in Part 8 ‘Building Services, Section 2
room of 4 h fire resistance rating, and this
Electrical Installations’.
room shall be situated on the periphery of the
basement. Catch-pits shall be provided at the C-5 FIRE CONTROL ROOM
low level.
For all buildings 15 m in ~lght or above and apartment
c) Entry to this room shall be provided with a
buildings with a height of 30 m and above, there shall
composite door of 2 h fire resistance.
be a control room on the entrance floor of the building
d) The boiler room shall be provided with fresh with communication system (suitable public address
air inlets and smoke exhausts directly to the system) to all floors and facilities for receiving the
atmosphere. message from different floors. Details of all floor plans
e) The furnace oil tank for the boiler, if located along with the details of fire fighting equipment and
in the adjoining room shall be separated by installations shall be maintained in the fire control
fire resisting wall of 4 h rating. The entrance room. The fiie control room shall also have facilities
to this room shall be provided with double to detect the fire on any floor through indicator boards
composite doors. A curb of suitable height connection; fire detection and alarm systems on all
shall be provided at the entrance in order to floors. The fire staff incharge of the fire control room

70 NATIONAL BUILDING CODE OF INDIA


shall be responsible for the maintenance of the various inside and outside the building, shall be strictly
services and fire fighting equipment and installations maintained by the occupants and/or the owner of the
in co-ordination with security, electrical and civil staff building.
of the building.
C-8 FIRE DRILLS AND FIRE ORDERS
C-6 FIRE OFFICER FOR HOTELS, BUSINESS
Fire notices/orders shall be prepared to fulfil the
AND MERCANTILE BUILDINGS WITH HEIGHT
requirements of fire fighting and evacuation from the
MORE THAN 30 m
buildings in the event of fire and other emergency. The
C-6.1 A qualified Fire Officer with experience of not occupants shall be made thoroughly conversant with
less than 3 years shall be appointed who will be their actions in the event of emergency, by displaying
available on the premises. fire notices at vantage points and also through regular
training. Such notices should be displayed prominently
C-6.2 The Fire Officer shall:
in broad lettering.
a) maintain the fire fighting equipment in good
For guidelines for fire drills and evacuation procedures
working condition at all times,
for high rise buildings, see Annex E.
b) prepare fire orders and fire operational plans
and get them promulgated, C-9 COMPARTMENTATION
c) impart regular training to the occupants of the
The building shall be suitably compartmentalized so
buildings in the use of fire fighting
that fire/smoke remain confined to the area where fire
equipments provided on the premises and
incident has occurred and does not spread to the
keep them informed about the fire emergency
remaining part of the building.
evacuation plan,
d) keep proper liaison with city Fire Brigade, and C-10 HELIPAD
e) ensure that all fire precautionary measures are
For high rise buildings above 60 m in height, provision
observed at the times.
for helipad should be made.
NOTE — Competent authority having jurisdiction may
insist on compliance of the above rules in case of
C-n MATERIALS FOR INTERIOR
buildings having very large areas even if the height is
less than 30 m.
DECORATION/FURNISHING

The use of materials which are combustible in nature


C-7 HOUSE KEEPING
and may spread toxic fume/gases should not be used
To eliminate fire hazards, good house keeping, both for interior decoration/furnishing, etc.

ANNEX D

(Clauses 6.7.3.3 (a) and 6.7.5)


FIRE PROTECTION CONSIDERATIONS FOR VENTING IN INDUSTRIAL BUILDINGS

D-1 APPLICATION AND SCOPE D-2 SMOKE AND FIRE VENTING


D-1.l The provisions given below are applicable D-2.1 The basic consid&ations for formulating the
only to single storey industrial buildings (factories design and other requirements for smoke andfme vents
and storage buildings) covering large floor areas are as given in D-2.1.1 to D-2.1.20.
without sub-dividinglseparating walls which are
usually designed to meet modern production D-2.1.1 The smoke and hot combustion products from
methods. a fire, being lighter than the surrounding air, tend to
rise and on reaching the roof or ceiling spread out
D-1.2 The requirements of fire and explosion venting
(mushroom) on all sides and forma layer which floats
of industrial buildings, as dealt with in this section,
on top of the cold air beneath. In the absence of vents,
fall under two categories:
this layer becomes progressively deeper until the whole
a) Smoke and fire venting, and building is filled with hot smoky gases. The time
b) Explosion relief vents. consumed for this to happen may be only a few

PART 4 FIRE AND LIFE SAFETY 71


minutes, depending on variables like, type of materials packaging of the combustible materials as well as the
on fire, processlstorage conditions involved, etc. size, height and disposition of the stacks of materials.

D-2.1.2 The hot gases at the roof level moved by D-2.1.12 In industrial buildings of floor area less than
convection currents contribute to rapid lateral spread 750 m2 and used as low fire hazard occupancies,
of fire. conventional ventilators fitted high up near the eaves
of the external walls may serve as vents for smoke and
D-2.1.3 The provision of properly designed and
hot gases, provided care is taken to ensure that they
suitably located vents in adequate number helps the
are kept open at all times or are designed to open
speedy removal of smoke and hot gases, thereby
automatically in case of fire.
preventing spread of fire, besides reducing risks of
explosion of unburnt gases and reducing damage to D-2.1.13 Extinction of fires by closing the doors and
the contents and structure of the building by heat and windows is not likely in the case of industrial buildings
smoke. In addition, they facilitate fire fighting because of their large size, where sufficient air to
operations, and minimize personal hazards to the sustain the fire at least in the initial stages can be
firemen. expected to be present.

D-2.1.4 The time taken for accumulation of smoke D-2.1.14 Of the two types of building ventilation,
and hot gases within a building on fire being very short, namely, vertical and horizontal, vertical ventilation is
the venting devices installed shall be designed to the one commonly adopted in the case of single storey
operate in the early stage of the fire and must be industrial buildings.
automatic so as to ensure speed and efficiency in their
D-2.1.15 Since 70 to 80 percent of heat produced in a
operation.
fire is convective heat, the ventilation system has to
D-2.1.5 The smoke and fire venting system shall be be suitably designed to ensure early outflow of the heat
designed in such a manner as to keep the temperature and thereby minimize fire spread.
of the combustion products from the fire as low as
D-2.1.16 Combustible roof linings shall be avoided,
possible, preferably below approximately 150”C.
as they themselves will contribute to the spread of fire,
D-2.1.6 Automatic venting systems are complement~ thereby multiplying the venting problems.
to the fire extinguishing systems, and automatic
D-2.1.17 A wind blowing across a flat roof or a roof
sprinklers, where provided, should operate before the
with a pitch under 40° produces a negative pressure,
operation of the vents; otherwise, venting may delay
that is, it tends to draw gases out of the building and so
sprinkler operation.
aids venting of hot gases. Wind blowing across a roof
D-2.1.7 It is easier to vent a building of smoke than of pitch greater than 40° will draw gases out on the
clear it of smoke once it has been filled. leeward side, but oppose outward flow on the
windward side of the roof.
D-2.1.8 Venting is particularly desirable in large area
industrial buildings or warehouses, windowless D-2.1.18 For vents to work at full efficiency, the area
buildings, underground structures or in areas housing of the inlets for cold air entering the compartment must
hazardous operations. Automatic fire vents shall be equal at least the total area of the vents. Ideally, the
provided for all industrial occupancies (including inlets shall be as close to the ground as possible. ,
storage buildings) classified as medium hazard or
D-2.1.19 Where roof verlts are installed in a single-
above having floor areas exceeding 750 m2, irrespective
of whether they are compartmentalized or not. storey building any neighboring buildings,
particularly those of more than one storey, will be
D-2.1.9 These provisions do not cover other aspects, subject to some degree of eKposure hazard either from
of ventilation (or lighting) designed for regulation of flying birds or radiation, or both, as a result.
temperature within a building for personal comfort or
meeting process needs. D-2.1.20 If vents are to be installed, the size, design,
number and disposition of the vents and the associated
D-2.1.1O Similarly, fue and smoke venting requirements roof screens/curtain boards have to be assessed after
as given hereunder are also not applicable to multi-storey careful analysis of the various factors stated
buildings, as their requirements are different and more under D-2.1.1 1 above, as well as other related factors
complex. like type of building construction, nature and height
D-2.1.11 It is difficult to determine precise venting of roof, process hazards, exposure hazard, etc.
requirements on account of the many variables
D-2.2 Venting Area
involved. For instance, the rate of combustion varies
appreciably according to the nature, shape, size and D-2.2.1 The estimated requirements for ventilation ~e

72 NATIONAL BUILDING CODE OF INDIA


T-

Iargely based on the assumed build-up of the fire from which shall be designed for both manual and automatic
the time of initial outbreak to the time of effective fire operation.
fighting action by fire brigade.
D-2.3.7 Sawtooth roof skylight shall be considered as
D-2.2.2 The vent area required to be provided shall satisfactory for venting purposes only when designed
be approximately proportional to the perimeter of the for automatic operation.
fire area, because the entrained air forms the bulk of
D-2.3.8 Likewise, exterior wall windows shall not be
the vented gases.
reckoned as satisfactory means for venting of fire gases
D-2.2.3 The effective area shall be the minimum cross- and smoke in industrial buildings. However, they may
sectional area through which the hot gases must flow be reckoned as additional means of venting when, they
out to the atmosphere. are located close to the eaves and are provided with
ordinary glass or movable sash arranged for both
D-2.2.4 No consideration shall be given to the
manual and automatic operation.
increased air movement obtained by power operated
fans, since it must be assumed that in the event of fire, D-2.3.9 Baffles shall not be installed inside vents, as
power will be interrupted, or fans damaged by heat. they greatly reduce the effective area for venting.

D-2.2.5 The total vent areas to be provided shall be D-2.4 Vent Operation
as per the following ratios of effective area of vent
openings to floor area for various occupancy D-2.4.1 The vents shall be automatic in operation,
classifications indicated: unless where specified in these provisions that they
shall be designed for both manual and automatic
a) Low heat release content 1:150 operation. .-
(Sub-division G-1 )
D-2.4.2 The release mechanism shall be simple for
b) Moderate heat release content I:1OO
operation and independent of electrical power, since
(Sub-division G-2)
electrical services may be interrupted by fire.
c) High heat release content 1:30 to 1:50
D-2.4.3 The automatic operation of vents shall be
(Sub-division G-3)
achieved by actuation of fusible links or other types of
D-2.3 Types of Vents heat and smoke detectors, or by interlocking with
operation of sprinkler system or any other automatic
D-2.3.1 Venting shall be accomplished by any of the fire extinguishing system covering the area. Following
types such as monitors continuous gravity vents, until their release, the vents shall be designed to open by a
type vents or sawtooth roof skylights. system of counterweights and associated equipment
D-2.3.2 Where monitor type vents are installed, wired utilizing the force of gravity or spring loaded levers.
glass or metal panels shall be used only if the sash is D-2.4.4 Automatic fire alarm system, where installed,
arranged to open automatically. shall be coupled to the automatic vents to ensure
D-2.3.3 The use of plain thin glass for venting shall simultaneous operation.
be avoided on account of its unpredictable behaviour D-2.4.5 Automatic sprinklers, where installed, shall
during fire. However, if glass or other suitable plastic operate before the vents open in order to avoid any
sheet materials with early disintegration characteristics likely delay in sprinkler operation. However, heat
are used, they should be designed for automatic actuated devices used for vent release shall be suitably
operation. shielded from sprinkler discharge so that water does
not delay their action.
D-2.3.4 Where monitors or unit type vents are used,
the panels shall be hinged at the bottom and designed D-2.4.6 Premises where height of roof apex is 10 m
to open automatically. Both sides of the vents shall be or more or where the materials handled or stored have
designed to vent simultaneously to ensure that their high smoke producing characteristics, in addition to
effectiveness at the time of fire is not in any way fusible links, the vent release mechanism shall be
impeded by wind direction. interlinked to smoke actuated automatic fire detectors
to ensure early operation of vents.
D-2.3.5 Where movable shutters are provided
for continuous gravity vents, these shall open D-2.4.7 Non-comosive materials shall be used for
automatically in the event of fire. hinges, hatches and other related parts to ensure long
fail-safe operation of the vents.
D-2.3.6 Unit type vents shall be of relatively small
area, ranging between 1 mz and 9 mz, having light D-2.4.8 In case of any doubts regarding the types of
weight metal frames and housing with hinged dampers vents required to be installed for any particular

PART 4 FIRE ANDLIFE SAFETY 73


occupancy, authorities having jurisdiction shall be substantially assist in early operation of automatic
consulted. sprinklers and vents.

D-2.5 Size, Spacing and Disposition of Vents D-2.6.2 They shall be of sheet metal or any other
substantial non-combustible material strong enough to
D-2.5.1 Vents shall be correctly sited to ensure their withstand damage by heat or impact.
functional efficiency. Ideally, they shall be sited at the
highest point in each area to be covered. D-2.6.3 They shall be reasonably gas-tight, although
small openings for passage of pipes, conduits, etc, shall
D-2.5.2 They shall, as far as possible, be located be permitted.
immediately above the risk to be protected so as to
allow free and speedy removal of smoke and other D-2.6.4 They shall extend down from the roof/ceiling
combustion products in the event of fire. for a minimum depth of 2.2 m. Around specific
hazards, the depth shall be 4 m. Where roof/ceiling
D-2.5.3 The minimum dimension for an effective vent height exceeds 15 m they shall extend down to within
opening shall be not less than 1.25 m in any direction. 3 m of the floor. For pitched sawtoothed roofs, they
D-2.5.4 The spacing of the individual vents shall be shall extend down to truss level dividing the roof into
based on the principle that more number of well compartments.
distributed smaller vents are more effective than less
D-2.6.5 In moderate hazard occupancies, the distance
number of badly located larger vents.
between the screens/curtain boards shall not exceed
D-2.5.5 The maximum spacing between vents for the 75 m and the curtained areas shall be limited to a
three occupancy classifications shall be as follows: maximum of 4500 mz. ..
a) Low heat release content — 45 m between D-2.6.6 In high hazard occupancies, the distance
centres between screens shall not exceed 30 m and the
b) Moderate heat release content — 36 to 37 m curtained area shall be limited to 750 m2.
between centres D-2.6.7 The curtained roof area shall be so arranged
c) High heat release content — 22.5 to 30 m that they effectively aid in the venting of smoke and
between centres, depending on the severity hot gases through the automatic vents provided in each
of fire potential. area.
D-2.5.6 Vents shall be placed in a sheltered situation D-2.6.8 In sprinklered buildings, the screens shall
where advantage can be taken of the prevailing wind. preferably be so located as to coincide with the
The design of the vent shall be such as to produce a individual sprinkler system areas.
suction effect. A wind blowing across a flat roof or
one with a pitch be 40° produces a negative pressure, D-3 EXPLOSION RELIEF VENTS
that is, it tends to draw gases out of the building and so
D-3.1 Industrial premises where combustible dusts can
aids venting of hot gases. Wind blowing across a roof
accumulate or where flammable gases, vapours or mists
of pitch greater than 40° will draw gases out on the
in explosive concentrations may be present are
leeward side, but oppose outward flow on the
constantly exposed to explosion hazards. Pressures
windward side of the roof.
developed by such explosions may be of the order of
D-2.5.7 Low level inlets, with total area not less than 7 x 105 Pa and ordinary buildings will not be able to
the total area of vents, shall be provided to permit withstand the shock of such pressures. Hence, such
outside air to be drawn in to aid automatic venting. buildings require explosion relief vents for preventing
These inlets, which may be in the form of doors, structural damage.
windows or such other openings, shall be designed for
D-3.2 Basic Principle/Considerations
manual operation when desired.
D-3.2.1 Most ordinary building walls will not
D-2.6 Roof Screens or Curtain Boards
withstand a sustained internal pressure as great as
D-2.6.1 Industrial buildings with large areas and 6.9 x 103 Pa. Hence, explosion relief vents for
having no sub-divisionkeparating walls limiting the buildings must be designed to operate at pressures well
area of individual compartments to 750 m2 or less, shall below those at which the building walls will fail.
be provided with roof screens or curtain boards.
D-3.2.2 There is a rise in pressure during an explosion
These screens which extend from the roof downwards within an enclosure even with open, unobstructed
at specific intervals not only prevent lateral spread of vents, and any delay in opening the venting devices .
heat and smoke in the event of fire below, but increases that pressure.

74 NATIONAL BUILDING CODE OF INLXA


D-3.2.3 Structural damage can be minimized by D-3.2.14 Rectangular unrestricted vents are as
locating hazardous operations or equipment outside effective as square vents of equal area.
buildings and cut off from other operations by a
pressure resisting wall. Such isolated processes or D-3.3 Types of Explosion Relief Vents
equipment shall be housed in single-storey buildings D-3.3.1 The explosion relief vents shall be any one or
properly vented and a device provided at the inlet of more of the following types, depending on individual
the collector which will prevent an explosion from requirements as assessed by the Authority. Open or
blowing back through the duct work and into the unobstructed vents, louvers, open roof vents, hanger
building. type doors, building doors, windows, roof or wall
D-3.2.4 Where highly hazardous operations cannot be panels or movable fixed sash.
located outside of main buildings they shall be D-3.3.2 The effect of external wind pressure or suction
segregated by pressure resisting walls and each such on these devices shall be taken into consideration while
unit shall be ventilated outdoors. External walls may designing and selecting the type of vents, since wind
be of heavy construction if equipped with suitable vents pressures may reach over 2 x I@’ Pa in severe wind
or high weight panels which blow out easily. storms.
D-3.2.5 Operations or equipment involving explosion D-3.3.3 The type of vent for explosion relief for any
hazards shall not be permitted in basements or areas occupancy shall be selected with life safety as the
partially below grade. primary aim followed by minimum damage to
D-3.2.6 Fire can be expected to follow an explosion in property.
most occupancies, so that any fixed fire extinguishing D-3.3.4 Where large hanger type doors or metal
equipment, like sprinklers, if installed, shall be such curtain doors in side walls are used as vents care shall
that only the minimum damage is caused to it. be taken to ensure that they are kept wide open during
D-3.2.7 For a given material, the finer the particle size operations.
of the dust, the more violent is the explosion. Some D-3.3.5 Where weather hoods are used to cover roof
materials, such as aluminium powder, hydrogen, and vents, they shall be as light as possible and lightly
acetylene, are difficult to vent effectively due to the attached so as to enable them to be blown off quickly
rapid rate of pressure rise. Some slow burning when an explosion occurs.
materials, such as coal dust in a confined space, may
do much damage because of the longer duration of D-3.3.6 Doors and windows when used as explosion
their presence. Some dusts, such as magnesium, vents shall be installed to swing outwards. Doors shall
titanium and zirconium and several metal hydrides may have friction, spring or magnetic latches that will
react with water and ignite in some common inert function automatically to permit the door to open under
gases, such as nitrogen and carbon dioxide. slight internal pressure.

D-3.2.8 The maximum explosion pressure in a vented D-3.3.7 Movable sash shall be of the top or bottom
structure decreases as the size of the vent increases, but hinged or protected type. These shall be equipped with
is independent of the rupturing pressure of a diaphragm. a latch or friction device to prevent accidental opening
due to wind action or intrusion. Such latches or locks
D-3.2.9 The most effective vent for the release of shall be well maintained.
explosion pressures is an unobstructed vent opening.
D-3.3.8 Fixed sash shall be set in place with very light
D-3.2.1O Pressure required to rupture diaphragms of wall anchorages, or, if right, shall be securely fitted
the same area and material directly varies with the and glazed with plastic panes in plastic putty.
thickness of the material.
D-3.3.9 Where the process is such that the whole of a
D-3.2.11 The slower the rate of pressure rise, the more building or a room may be desirable to arrange for a
easily can the explosion be vented. lightly constructed wall or roof to collapse and thus
D-3.2.12 The degree of venting required is directly avert the worst effects of an explosion.
proportional to the degree of explosion hazard.
D-3.4 Design, Size and Disposition of Vents
D-3.2.13 Experience has shown that most explosions
D-3.4.1 The required area of explosion vents shall
of dusts, vapours and gases do not involve a large part
ordinarily depend on the expected maximum intensity
of the total volume of the enclosure, and frequently
of an explosion in the occupancy, the strength of the
occur near the upper or lower limits of the explosive
structure, the type of vent closure and other factors.
range. Consequently, such explosions are relatively
weak compared with the optimum. D-3.4.2 Venting shall be planned in such a manner as

PART 4 FIRE AND LIFE SAFETY 75


to prevent injury to personnel and damage to D-3.4.14 If closed vents are used they shall be larger
exposures. In congested locations, substantial ducts in area than unenclosed vents to provide equivalent
or diverters shall beprovided todirect the blast. explosion pressure relief.

D-3.4.3 When ductwork isused, theductsshall beef D-3.4.15 Small enclosures, such as machines, shall
sufficient strength to withstand the maximum expected be vented more generously than buildings, because if
explosion pressure. an explosion occurs in a machine, its entire volume
.
may be involved.
D-3.4.4 Where explosions are likely within duct and
piping systems, they shall be vented by the use of D-3.4.16 Vents for the protection of buildings and
suitable diaphragms designed to blow out at a equipment shall be installed on the following basis:
predetermined pressure. There shall be no physical
D-3.4 .16.1 Small enclosures of less than 30 m3,
connection between ductwork system for more than
machines and ovens of light construction: 1000 cmz
one collector.
for each 0.3 m3 to 0.9 m3.
D-3.4.5 In large structures, the position of vents shall
D-3.4.16.2 For small enclosures of more substantial
be relative to the point of origin of explosion, when it
construction having reasonably high bursting strength:
can be determined.
1000 cm2 for each 0.9 m3.
D-3.4.6 Where relatively slow explosions involving
D-3.4.16.3 Fairly large enclosures of 30 to 700 m3,
coal dust, chlorinated solvents, etc, are involved, light,
such as bins, silos, rooms, storage tanks, etc: 1000 cm2
hinged swinging panels may be preferred to diaphragm
for each 0.9 m3 to 1.5 m3. In these cases, attempt shall
type of vents.
be made to the extent possible to predict the likely point
D-3.4.7 Obstructions of any kind blocklng the vents of origin of the explosion in relation to the vent.
from the risk covered shall be avoided, particularly
D-3.4.16.4 Large rooms and buildings over 700 m3
where risks of rapid violent explosions are present.
containing hazardous equipment comprising a small
D-3.4.8 Counter weights add to the inertia of the vents fraction of the entire volume:
and so shall be avoided.
a) For heavy reinforced concrete, walls —
D-3.4.9 Various relieving devices, including devices 100 cm2 for each 2.25 m3.
actuated by detonators, shall start to open at as low a b) For light reinforced concrete, brick or wood
pressure as possible. They shall be of light construction, construction — 1 000 cmz for each 1.65 m3
so that full opening can be quickly attained. to 2.25 m3.
D-3.4.1O Vents shall be of such size and design as to c) For lightweight construction such as
prevent rupture of the protected device or apparatus. prefabricated panels — 1000 cm2 for each
1.5 m3 to 1.65 m3.
D-3.4.11 Skylights or monitors with movable sash that
will open outwards, or fixed sash containing panes of D-3.4 .16.5 Large rooms or building over 700 m3
glass or plastic that will blow out readily under pressure containing hazardous equipment comprising a large
from within, can be used to supplement wall vents or part of the entire volume of a room or building shall
windows, provided resistance to their displacement or be vented as generously as possible 1000 cm2 for each
opening is kept as low as consistent with the 0.3 m3 to 1.05 m3.
requirements for structural strength. D-3.4.16.6 In order to obtain these ratios, the size of
D-3.4.12 Flexible plastic sheets when used for vent the building or room must be limited. For some
hazardous materials, such as hydrogen, acetylene,
closures shall be installed in slotted frames in such a
way that pressure from within bulges the sheets and carbon disulphide, etc, thes?e limits are extremely low.
releases them from the holding frame. D-3.4.17 Emphasis shall always be placed on
segregating hazardous areas by means of firewalls or
D-3.4.13 Fragile sheets made of plastic, when used
separating walls to prevent spread of fire.
for vent closures, shall be thin sheets that will crack or
rupture under less pressure than single strength glass. D-3.4.18 Interior walls of light construction, such as
For this reason use of transparent or translucent plastic tile, shall be avoided in hazardous locations, since they
sheets is more advantageous instead of glass in window can cause injuries to personnel in the event of an
sash. explosion.

76 NATIONAL BUILDING CODE OF INDIA


ANNEX E
(Clause C-8)
GUIDELINES FOR FIRE DRILL AND EVACUATION PROCEDURES FOR
HIGH RISE BUILDINGS (ABOVE 15 m IN HEIGHT)

E-1 INTRODUCTION background. Such lettering shall be properly spaced


to provide good legibility. The sign shall be at least
In case of fire in a high rise building, safe evacuation
250 mm x 300 mm, where the diagram is also
of its occupants may present serious problems unless
incorporated in it and 62.5 mm x 250 mm where the
a plan for orderly and systematic evacuation is prepared
diagram is omitted. In the latter case, the diagram sign
in advance and all occupants are well drilled in the
shall be at least 200 mm x 300 mm. The sign shall be
operation of such plan. These guidelines are intended
located directly above a call-button and squarely
to assist them in this task.
attached to the wall or partition. The top of the sign
E-2 ALARMS shall not be above 2 m from the floor level.

Any person discovering fire, heat or smoke shall E-4.2 Floor Numbering Signs
immediately report such condition to the fire brigade,
A sign shall be posted and maintained within each
unless he has personal knowledge that such a report
stair enclosure on every floor, indicating the number
has been made. No person shall make, issue, post or
of the floor, in accordance with the requirements
maintain any regulation or order, written or verbal, that
given below.
would require any person to take any unnecessary
delaying action prior to reporting such condition to The numerals shall be of bold type and at least 75 mm
the fire brigade. high. The numerals and background shall be in
contrasting CO1OWS.The sign shall be securely attached
E-3 DRILLS to the stair side of the door.
E-3.1 Fire drills shall be conducted, in accordance with
E-4.3 Stair and Elevator Identification Signs
the Fire Safety Plan, at least once every three months
for existing buildings during the first two years. Each stairway and each elevator back shall be identified
Thereafter, fire drills shall be conducted at least once by an alphabetical letter. A sign indicating the letter of
every six months. identification shall be posted and maintained at each
elevator landing and on the side of the stairway door
E-3.2 All occupants of the building shall participate
from which egress is to be made, in accordance with
in the fire drill. However, occupants of the building,
the requirements given below:
other than building service employees, are not required
to leave the floor or use the exits during the drill. The lettering on the sign shall be at least 75 mm high,
of bold type and of contrasting colour from the
E-3.3 A written record of such drills shall be kept on
background. Such signs shall be securely attached.
the premises for a three years period and shall be readily
available for fire brigade inspection. E-4.4 Stair Re-entry Signs

E-4 SIGNS AND PLANS A sign shall be posted and maintained on each floor
within each stairway and on the occupancy side of the
E-4.1 Signs at Lift Landings stairway where required, indicating whether re-entry
A sign shall be posted and maintained in a conspicuous is provided into the build$ng and the floor where
place on every floor at or near the lift landing in such re-entry is provided, in accordance with the
accordance with the requirements, indicating that in requirements given below:
case of fire, occupants shall use the stairs unless The lettering and numerals of the signs shall be at least
instructed otherwise. The sign shall contain a diagram 12.5 mm high of bold type. The lettering and
showing the location of the stairways except that such background shall be of contrasting colours and the
diagram may be omitted, provided signs containing signs shall be securely attached approximately 1.5 m
such diagram are posted in conspicuous places on the above the floor level.
respective floor.
E-4.5 Fire command station shall be provided with
A sign shall read “IN CASE OF FIRE, USE STAIRS floor plan of the building and other pertinent
UNLESS INSTRUCTED OTHERWISE”. The lettering information relative to the service equipment of the
shall be at least 12.5 mm block letters in red and white building.

PART 4 FIRE AND LIFE SAFETY 77


P’-

E-5 FIRE SAFETY PLAN written programme for all occupants, to ensure prompt
reporting of fire, the response of fire alarms as
E-5.1 A format for the Fire Safety Plan shall be as
designated, and the immediate initiation of fire safety
given in E-8.
procedures to safeguard life and contain fire until the
E-5.2 The applicable parts of the approved Fire Safety arrival of the fire brigade.
Plan shall be distributed to all tenants of the building
by the building management when the Fire Safety Plan E-8.3 Fire Safety Director
has been approved by the Fire Authority. a) Name
E-5.3 The applicable parts of the approved Fire Safety b) Regularly assigned employment — Title
Plan shall then be distributed by the tenants to all their c) Regularly assigned location
employees and by the building management to all their d) How is he notified when at regular location?
building employees.
e) How is he notified when not at regular location?
E-5.4 Where the owner of the building is also an f) Normal working hours
occupant of the building, he shall be responsible for g) Duties of Fire Safety Director (see E-9.1)
the observance of these rules and the Fire Safety Plan
in the same manner as a tenant. E-8.4 Deputy Fire Safety Director

E-5.5. In the event there are changes from conditions a) Name


existing at the time the Fire Safety Plan for the building b) Regularly assigned employment — Title
was approved, and the changes are such so as to require c) Regularly assigned location &
amending the Fire Safety Plan, within 30 days after
d) How is he notified when at regular location?
such changes, an amended Fire Safety Plan shall be
e) How is he notified when not at regular
submitted to the fiie brigade for approval.
location?
E-6 FIRE COMMAND STATION f) Normal working hours

A Fire Command Station shall be established in the g) Duties of Deputy Fire Safety Director
lobby of the building on the entrance floor. Such (see E-9.2)
command station shall be adequately illuminated.
E-8.5 Fire Wardens and Deputy Fire Wardens
E-7 COMMUNICATIONS AND FIRE ALARM a) Are their names on Organization Charts for
A means of communication and flue alarm for use during each floor andlor tenancy?
fire emergencies shall be provided and maintained by b) Submit typical completed Organization Chart
the owner or person in charge of the building. for Fire Drill and Evacuation Assignment.
c) Duties of Fire Wardens and Deputy Fire
E-8 FIRE SAFETY PLAN FORMAT Wardens (see E-9.3).
E-8.1 Building Address
E-8.6 Building Evacuation Supervisor
Street and Pin Code Number ...............................
a) Name
Telephone Number ...............................................
b) Regularly assigned employment — Title
E-8.2 Purpose and Objective c) Regularly as~i~ed location

E-8.2.1 Purpose d) How is he notified when at regular location?


e) .How is he notik@ when not at regular location?
To establish method of systematic, safe and orderly
f) Normal working hours
evacuation of an area or building by its occupants in
case of fire or other emergency, in the least possible g) Duties of Building Evacuation Supervisor
time, to a safe area by the nearest safe means of egress; (see E-9.4).
also the use of such available fire appliances (including
E-8.7 Fire Party
sounding of alarms) as may have been provided for
controlling or extinguishing fire and safeguarding of a) Submit a completed Organization Chart for
human life. Fire Parties naming person in charge, and his
title in the building.
E-8.2.2 Objective
b) Indicate standards of selection from building
To provide proper education as a part of continuing employees based on background and
employee indoctrination and through a continuing availability.

78 NATIONAL BUILDING CODE OF INDIA


c) How are they notified? E-9.1.2 Select qualified building service employees
d) How are they notified when they are not at for a Fire Party and organize, train and supervise such
their regular locations? Fire Brigade.
e) Means of responding E-9.1.3 Be responsible for the availability and state
f) Duties of each member of Fire Party of readiness of the Fire Party.
(see E-9.5).
E-9.1.4 Conduct fire and evacuation drills.
E-8.8 Occupants Instructions
E-9.1.5 Be responsible for the designation and training
Distribution of instructions to all tenants, tenents’ of a Fire Warden for each floor, and sufficient Deputy
employees and building employees (see E-9.6). Fire Wardens for each tenancy in accordance with
orders on the subject.
E-8.9 Evacudion Drills
E-9.1.6 Be responsible for a daily check for the
a) Frequency of drills
availability of the Fire Wardens, and see that up-to-
b) How conducted?
date organization charts are posted.
c) Participation: Who participated? How?
NOTE — If the number of Fke Wardens and Deputy Fire
d) Controls and supervision Wardens in the building is such that it is impractical to
e) Recording of details of drills individually contact each one daily, a suggested method to
satisfy the requirements is to make provisions for the Fire
E-8.1O Fire Command Station Warden, or a Deputy Fire Warden in the absence of the Fire
Warden, to notify the Fire Safety Director when the Fire
a) Location Warden or required number of Deputy Fire Wardens are not
b) Requirements available. In order to determine the compliance by the Fire
Wardenand Deputy Fke Wardens,when this method is used,
1) Adequate illumination the Fire Safety Director shall make a spot check of several
2) Adequate communication to mechanical different floors each day.
equipment room and elevator control
E-9.1.7 Notify the owner or some other person having
room on each floor
charge of the building when any designated individual
3) Copy of Fire Safety Plan is neglecting his responsibilities contained in Fire
4) Copy of Building Information Form Safety Plan. The owner or the other person in-charge
5) Representative floor plans showing of the building shall bring the matter to the attention
location of signs, floor remote station, of the firm employing the individual. If the firm fails
communications, etc. to correct the condition, the Fire Department shall be
notified by the ownerlperson in-charge of the building.
E-8.11 Signs
E-9.1.8 In the event of fire, shall report to the Fire
a) Signs at elevator landings, Floor diagrams
Command Station to supervise, provide for and
b) Floor numbering coordinate:
c) Stairway identification
a) Ensure that the Fire Department has been
d) Elevator identification
notified of any fire or fire alarm.
e) Stair re-entry
b) Manning of the Fire Command Station.
E-8.12 Fire Prevention and Fire Protection c) Direction of evacuating procedures as
Programme (see E- 9.7). provided in the Fire Safety Plan.
E-8.13 Building Information Form (see E-9.8). d) Reports on conditions on fire floor for
information of F@e Department on their
E-8.14 Representative Floor Plan (see E-9.9). arrival.
E-8.15 Fire Safety Plan Prepared by (see E-9.1O). e) Advise the Fire Department Officer in-charge
in the operation of the Fire Command Station.
a) Date when prepared.
b) Date when revised. E-9.1.9 Be responsible for the training and activities
of the Building Evacuation Supervisor.
E-9 DUTIES
E-9.2 Deputy Fire Safety Director’s Duties
E-9.1 Fire Safety Director’s Duties
E-9.2.1 Subordinate to the Fire Safety Director.
E-9.1.1 Be familiar with the written Fire Safety Plan
providing for fire drill and evacuation procedure in E-9.2.2 Perform duties of Fire Safety Director in his
accordance with orders on the subject. absence.

PART 4 FIRE AND LIFE SAFETY 79


y--

E-9.3 Fire Wardens and Deputy Fire Wardens and/or floors above are unusable due to
Duties contamination or cut off by fire and/or smoke
or that several floors above fire involve
The tenant or tenants of each floor shall, upon request
large numbers of occupants who must be
of the owner or person in charge of buildings, make
evacuated, consideration may be given to
responsible and dependable employees available for
using elevators in accordance with the
designation by the Fire Safety Director as Fire Warden
following:
and Deputy Fire Wardens.
1) If the elevators servicing his floor also
E-9.3.1 Each floor of a building shall be under the service the fire floor, they shall not be
direction of a designated Fire Warden for the used. However, elevators may be used if
evacuation of occupants in the event of fire. He shall there is more than one bank of elevators,
be assisted in his duties by the Deputy Fire Wardens. and he is informed from the Fire Command
A Deputy Fire warden shall be provided for each Station that one bank is unaffected by the
tenancy. When the floor area of a tenancy exceeds fire.
700 mz of occupiable space, a Deputy Fire Warden 2) If elevators do not service the fire floor
shall be assigned for each 700 m2 or part thereof. and their shafts have no openings on the
fire floor, they may be used, unless
E-9.3.2 Each Fire Warden and Deputy Fire Warden
directed otherwise.
shall be familiar with the Fire Safety Plan, the location
of exits and the location and operation of any available 3) Elevators manned by trained building
fiie alarm system. personnel or firemen may also be used.
.-
4) In the absence of a serviceable elevator,
E-9.3.3 In the event of fire, or fire alarm the Fire
the Fire Warden shall select the safest
Warden shall ascertain the location of the fire, and
stairway to use for evacuation on the
direct evacuation of the floor in accordance with
basis of the location of the fire and any
directions received and the following guidelines:
information received from the Fire
a) The most critical areas for immediate Command Station. The Fire Warden shall
evacuation are the fire floor and floors check the environment in the stairs prior
immediately above. to entry for evacuation. If it is affected
Evacuation from the other floors shall be by smoke, alternative stair shall be
instituted when instructions from the Fire selected, and the Fire Command Station
Command Station or conditions indicate such notified.
action. Evacuation shall be via uncontaminated 5) The Fire Warden shall keep the Fire
stairs. The Fire Warden shall try to avoid Command Station informed of the means
stairs being used by the Fire Department. If being employed for evacuation by the
this is not possible, he shall try to attract the occupants of his floor.
attention of the Fire Department Personnel g) Ensure that an alarm has been transmitted.
before such personnel open the door to the
fire floor. E-9.3.4 Organization Chart for Fire Drill and
Evacuation Assignment
b) Evacuation to two or more levels below the
fire floor is generally adequate. He shall keep A chart designating employees and their assignments
the Fire Command Station informed regarding shall be prepared and p,osted in a conspicuous place in
his location. each tenancy and on each floor of a tenancy that
c) Fire Wardens and their Deputies shall see that occupies more than on~floor and a copy shall be in
all occupants are notified of the fire, and that the possession of the Fire Safety Director. .
they proceed immediately to execute the Fire
E-9.3.5 Keep available an updated listing of all
Safety Plan.
personnel with physical disabilities who cannot use stairs
d) The Fire Warden on the fire floor shall, as unaided. Make arrangements to have these occupants
soon as practicable, notify the Fire Command assisted in moving down the stairs to two or more levels
Station of the particulars. below fire floor. Ifit is necessary to move such occupants
e) Fire Wardens on floors above the fire shall, to a still lower level during the fne, move them down
after executing the Fire Safety Plan, notify the stairs to the uppermost floor served by an uninvolved
the Fire Command Station of the means being elevator bank and then remove them the street floor by
used for evacuation and any other particulars. elevator. Where assistance is required for such
o In the event that stairways serving fire floor evacuation, notify Fire Safety Director.

80 NATIONAL BUILDING CODE OF JNDIA


E-9.3.6 Provide for Fire Warden identification during e) on arrival of the Fire Department, the Fire
fire drills and fires, such as using arrnband, etc. Party shall report to the Fire Command Station
for additional instructions.
E-9.3.7 Ensure that all persons on the floor are notified
of fire and all are evacuated to safe areas. A search f) have a member designated as runner, who
shall know the location of the nearest
must be conducted in the lavatories to ensure all are
telephone, and be instructed in its use. Such
out. Personnel assigned as searchers can promptly and
member shall immediately upon receipt of
efficiently perform this duty.
information that there is a fiie or evidence of
E-9.3.8 Check availability of applicable personnel on fire, go to the telephone, transmit an alarm
Organization Chart and provide for a substitute when and await the arrival of the Fire Department
the position on a chart is not covered. and direct such department to the fiie.

E-9.3.9 After evacuation, perform a head count to NOTE — A chart designating employees and their
assignmentsshall be prepared.
ensure that all regular occupants known to have
occupied the floor have been evacuated. E-9.6 Occupant’s Instructions

E-9.3.1O When alarm is received, the Fire Warden a) The applicable parts of the approved Fire
shall remain at a selected position in the vicinity of the Safety Plan shall be distributed to all tenants
communication station on the floor, in order to of the building by the building management
maintain communication with the Fire Command when the Fire Safety Plan has been approved
Station and to receive and give instructions. by the Fire Commissioner.
b) The applicable parts of the approved Fire
E-9.4 Building Evacuation Supervisor’s Duties
Safety Plan shall then be distributed by the
A building Evacuation Supervisor is required at all tenants to all their employees and by the
times other than normal working or business hours building management to all their building
when there are occupants in the building and there is employees.
no Fire Safety Director on duty in the building. c) All occupants of the building shall participate
and cooperate in carrying out the provisions
E-9.4.1 He should be capable of directing the
of the Fire Safety Plan.
evacuation of the occupants as provided by the Fire
Safety Plan. E-9.7 Fire Prevention andl%e Protection Pmgramme
E-9.4.2 During fire emergencies, the primary a) A plan for periodic formal inspections of each
responsibility of the Building Evacuation Supervisor floor area, including exit facilities, fire
shall be to man the Fire Command Station, and the extinguishers and house keeping shall be
direction and execution of the evacuation as provided developed. A copy of such plan be submitted.
in the Fire Safety Plan. The Building Evacuation
b) Provision shall be made for the monthly
Supervisor’s training and related activities shall be
testing of communication and alarm systems.
under the direction of the Fire Safety Director in
accordance with these rules, and the Fire Safety Plan. E-9.8 Building Information Form
Such activities shall be subject to Fire Department
control. It shall include the following information:

a) Building address . . . . . . . . . . . ..Pin Code . . ........


E-9.5 Fire Party Duties
b) Owner or person in-charge of building —
On receipt of an alarm for fire the Fire Party shall: Name, Address and Telephone Number.
a) report to the floor below the fire to assit in c) Fire Safety Directdr and Deputy Fire Safety
evacuation and provide information to the Director’s Name and Telephone Number.
Fire Command Station. d) Certificate of occupancy. Location where
b) after evacuations of fire floor, endeavour to posted, or duplicate attached.
control spread of fire by closing doors, etc. e) Height, area, class of construction.
c) attempt to control the tire until arrival of the f) Number, type and location of fwe stairs and/
Fire Department, if the fire is small and or fire towers.
conditions do not pose a personal threat. g) Number, type and location of horizontal exits
d) leave one member on the floor below the fire or other areas of refuge.
to direct the Fire Department to the fire h) Number, type, location and operation of
location and to inform them of conditions. elevators and escalators.

PART 4 FIRE AND LIFE SAFETY 81


T--

j) Interior fire alarms, or alarms to central Safety Director. One copy of a representative floor plan
stations. shall be submitted to the Fire Department with the Fire
k) Communications systems and/or walkie Safety plan.
talkie, telephones, etc.
E-9.1O Fire Safety Plan
m) Standpipe system; size and location of risers,
gravity or pressure tank, fire pump, location In planning, evaluate the individual floor layouts, the
of siamese connections, name of employee population of floors, the number and kinds of exits,
with certificate of qualification and number the zoning of the floor by area and occupants.
of certificate. Determine the movement of traffic by the most
n) Sprinkler system; name of employee with expeditious route to an appropriate exit and alternative
Certificate of Fitness and certificate number. route for each zone, since under tire conditions one or
Primary and secondary water supply, fire more exits may not be usable. This format is to be used
pump and areas protected. in the preparation of the Fire Safety Plan. Nothing
Special extinguishing system, if any, contained in this Fire Safety Plan format is to be
P)
components and operation. construed as all inclusive. All rules and other
requirements are to be fully complied with.
q) Average number of persons normally employed
in building. Daytime and night time.
E-9.11 Personal Fire Instruction Card
r) Average number of handicapped people in
building. Location. Daytime and night time. All the occupants of the building shall be given a
Personal Fire Instruction Card giving the details of the
s) Number of persons normally visiting the
floor plan and exit routes along with the instruction to
building. Daytime and night time.
be followed in the event of fire. A typical Personal
t) Service equipment such as:
Fire Instruction Card shall be as follows:
1) Electric power, primary, auxiliary;
2) Lighting, normal, emergency, type and PERSONAL FIRE
location;
INSTRUCTION CARD
3) Heating, type, fuel, location of heating
unit; SEAL
4) Ventilation — with fixed windows, NAME OF THE ORGANIZATION
emergency means of exhausting heat and
smoke; ADDRESS OF THE ORGANIZATION

5) Air-Conditioning Systems — Brief NAME: .........................................................................


description of the system, including ducts
DESIGNATION: .........................................................
and floors serviced;
6) Refuse storage and disposal; FLOOR NO.: ................................................................
7) Fire fighting equipment and appliances, DATE: ..........................................................................
other than standpipe and sprinkler
system; and FIRE WARDEN
8) Other pertinent building equipment.
INSTRUCTIONS
u) Alterations and repair operations, if any, and
the protective and preventive measures FOR YOUR OWN SAFETY YOU SHOULD KNOW
necessary to safeguard such operations with
1. Two push button fire alarm boxes are
attention to torch operations.
provided per ffoor. You should read the
v) Storage and use of flammable solids, liquids
operating instructions.
andlor gases.
2. You should read the operating instructions on
w) Special occupancies in the building and the
the body of the fire extinguishers provided
proper protection and maintenance thereof.
on your floor.
Places of public assembly, studios, and
3. The nearest exit from your table.
theatrical occupancies.
4. Your assembly point on ground floor (check
E-9.9 Representative Floor Plan with your Fire/Deputy Fire Warden).
A floor plan, representative of the majority or the floor 5. FOR YOUR OWN PROTECTION YOU
designs of the entire building, shall be at the Command SHOULD REPORT TO YOUR FIRE/
Post, in the main lobby, under the authority of the Fire DEPUTY FIRE WARDEN

82 NATIONAL BUILDING CODE OF INDIA


a) If any exit door/route is obstructed by loose 3. Evacuate if your Warden asks you to do so.
materials, goods, boxes, etc.
IF YOU HEAR EVACUATION INSTRUCTIONS
b) If any staircase door, lift lobby door does not
close automatically, or does not close 1. Leave the floor immediately by the soutld
completely. north staircase.
c) If any push button fire alarm point, or fire 2. Report to your Warden, at your predetermined
extinguisher is obstructed, damaged or assembly point outside the building.
apparently out of order. 3. Do not try to use lifts.
4, Do not go to cloakroom.
IF YOU DISCOVER A FIRE
5. Do not run or shout.
1. Break the glass of the nearest push button fire
6. Do not stop to collect personal belongings.
alarm and push the button.
7. Keep the lift lobby and staircase doors shut.
2. Attack the fire with extinguishers provided on
your floor. Take guidance from your Wardens. YOUR ASSEMBLY POINT IS . . . . . ............... . . . . . . . ..

LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’ 3844:1989 Code of practice for installation
in the fulfillment of the requirements of the Code. The and maintenance of internal fire
standards listed may be used by the Authority as a guide hydrants and hose reels on
in conformance with the requirements of the referred premises (first revision)
clauses in the Code. (7) 3614 Specification for fire check
(part 1): 1966 doors: Pmt 1 Plate, metal covered
IS No. Title
and rolling type
(1) 3808:1979 Method of test for non-
(8) 12458:1988 Method of test for fire resistance
combustibility of building
test for fire stops
materials (first revision)
(9) 1646:1997 Code of practice for fire safety
(2) 8757:1999 Glossary of terms associated
of buildings (general) :
with fire safety (jirst revision)
Electrical installations (second
7673:1975 Glossary of terms for fire revision)
fighting equipment
2309:1989 Code of practice for protection of
(3) 15394:2003 Fire safety in petroleum refinery building and allied structures
and fertilizer plants — Code of against lighting (second revision)
practice
(lo) ................ Specification for fire dampers
(4) 8758:1993 Recommendations for fire for air conditioning ducts (under
precautionary measures in the preparation)
construction of temporary
(11) 11360:1985 Specification for smoke
structures and PANDALS (first
detectors for use in automatic
revision) electrical fwe alarm system
(5) 3809:1979 Fire resistance test of structure Safe@ code for air-conditioning
(12) 659:1964
(jirst revision)
(13) 1649:1962 Code of practice for design and
1641:1988 Code of practice for fwe safety construction of flues and
of buildings (general): General chimneys for domestic heating
principles of fire grading and appliances (first revision)
classification (first revision)
1642:1989 Code of practice for safety of
15103:2002 Specification for fire resistant buildings (general): Details of
steel construction (/irst revision)
(6) 9668:1990 Code of practice for provision (14) 12777:1989 Fire safety-flame-spread of
and maintenance of water products — Method for
supplies and fire fighting classification

PART 4 FIRE AND LIFE SAFETY 83


1s No. Title IS No. Title
(15) 1642:1989 Code ofpractice for fire safety 906:1988 Specification for revolving
ofbuildings (general) : Detailsof branch pipe for fire fighting
constructionist revision) (third revision)
1643:1988 Code ofpractice for fire safety 907:1984 Specification for suction
of buildings (general): Exposure strainers, cylindrical type for fiie
hazard (first revision) fighting purpose (second revision)
1644:1988 Code of practice for fire safety 908:1975 Specification for fire hydrant,
of buildings (general): Exit stand post type (second revision)
requirements and personal
909:1992 Specification for underground
hazard (fzrst revision)
fire hydrant Sluice valve type
(16) 9457:1980 Safety colours and safety signs (third revision)
12349:1988 Fire protection — Safety sign 910:1980 Specification for combined key
12407:1988 Graphic symbols for fire for hydrant, hydrant cover and
protection plan lower valve (second revision)
(17) 2175:1988 Specification for heat sensitive 926:1985 Specification for fireman’s axe
fire detectors for use in (second revision)
automatic fire alarm system 927:1981 Specification for fire hooks
(second revision) (second revision)
11360:1985 Specification for smoke 928:1984 Specification for fire bells .-
detectors for use in automatic (second revision)
electrical fire alarm system .
937:1981 Specification for washers for
(18)2189 :1999 Code of practice for selection, water fittings for fire fighting
installation and maintenance of purposes (second revision)
automatic fire detection
939:1977 Specification for snatch block
and alarm system (second
for use with fibre rope for fire
revision)
brigade use (first revision)
(19) 636:1988 Non-percolating flexible fire
940:1989 Specification for portable fire
fighting delivery hose (third
extinguisher, water type (gas
revision)
cartridge) (third revision)
884:1985 Specification for first-aid hose
reel for fire fighting (first 941:1985 Specification for blowers and
revision) exhauster for fire fighting
(second revision)
901:1988 Specification for couplings,
942:1982 Functional requirements for 275-
double male and double female
instantaneous pattern for fire I/min portable pump set for fire
fighting (third revision) fighting (second revision)
943:1979 Functional requirement for 680-
902:1992 Specification for suction hose
l/min trailer pump for fire
couplings for fire fighting
purposes (third revision) brigade use (second revision)
944:1979 Functional requirement for
903:1993 Specification for fire hose
1800-1/min trailer pump for fire
delivery couplings, branch pipe,
brigtiiie use (second revision)
nozzles and nozzle spanner
(fourth revision) 947:1985 Functional requirement for
towing tender for trailer fire
904:1983 Specification for two-way and
three-way suction collecting pump for fire brigade use @rst
heads for fire fighting purposes revision)
(second revision) 948:1983 Functional requirement for water
905:1980 Specification for delivery tender, Type A, for fire brigade
breechings, dividing and use (second revision)
collecting, instantaneous pattern 949:1985 Functional requirement for
for fire fighting purposes (second emergency (rescue) tender for fire
revision) brigade use (second revision)

84 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title
950:1980 Functional requirements 4308:1982 Specification for dry powder for
forwatertender,Type Bforfire fire fighting (first revision)
brigade use (second revision) 4571:1977 Specification for aluminium
952:1986 Specificationforfoghnozzle for extension ladders for fire brigade
fire brigade use (j%-st revision) use first revision)
955:1980 Functional requirements for dry 4643:1984 Specification for suction
power tender for fire-brigade wrenches for fire brigade use
use (150 kg capacity) (first (/irst revision)
revision)
4861:1984 Specification for dry powder for
957:1967 Specification for control van for fighting fires in burning metals
fire brigade (/irst revision)
1941 Functional requirements for 4927:1992 Specification for unlined flax
(Rut 1): 1976 electric motor sirens: Part 1 ac 3 canvas hose for fire fighting
phase 50Hz,415 V type (second (first revision)
revision)
4928:1986 Specification for delive~ valve
2097:1983 Specification for foam making for centrifugal pump outlets
branch pipe (j?rst revision)
@rst revision)
2171:1999 Specification for portable fire
4947 :+4985 Specification for gas cartridges -.
extinguishers, dry powder
for use in fire extinguishers
(cartridge type) (third revision)
(second revision)
2175:1988 Specification for heat sensitive
4989 Specifications for multipurpose
fire detectors for use in
(Part 1): 2004 aqueous film forming foam
automatic detectors for use in
liquid concentrate for
automatic fire alarm system
extinguishing hydrocarbon
(second revision)
and polar solvent fires (third
2298:1977 Specification for single-barrel revision)
stirrup pump for fire fighting
4989 Specification for foam concentrate
purposes (second revision)
(Part 2): 1984 (compound) for producing
2546:1974 Specification for galvanized mechanical foam for fire
mild steel fire bucket (first fighting: Part 2 Aqueous film
revision) forming foam (AFFF)
2696:1974 Functional requirements for (Rat 3): 1987 Fluoro protein foam
1125 l/rein light fire engine
5131:1986 Specification for dividing
(first revision)
breeching with control, for fire
2745:1983 Specification for non-metal brigade use (jirst revision)
helmet for firemen and civil
5290:1993 Specification for landing valve
defence personnel (second
(third revision)
revision)
5486:1985 Specification for quick release
2871:1983 Specification for branch pipe,
knife (jirst revision)
universal for fire fighting
purposes (jirst revision) 5505:1985 Specification for multi-edged
rescue axe (non-wedging) @rst
2878:2004 Specification for fire
revision)
extinguisher, carbon-dioxide
type (portable and trolley 5612 Specification for hose-clamps
mounted) (third revision) and hose-bandages for fire
brigade use:
2930:1980 Functional requirements for
hose laying tender for fire (Part 1): 1977 Hose clamps (/irst revision)
brigade use @rst revision) (Part 2): 1977 Hose bandages (jirst revision)
3582:1984 Specification for basket strainers 5714:1981 Specification for hydrant, stand-
for fire fighting purposes pipe for fire fighting (first
(cylindrical type) (/irst revision) revision)

PART 4 FIRE AND LIFE SAFETY 85


r-

IS No. Title IS No. Title


6026:1985 Specification for hand-operated 12717:1989 Functional requirements of fire
sirens (’jirst revision) fighting equipment — High
6067:1983 Functional requirements for capacity portable pumpset
water tender, Type ‘X’ for fire (1 100-1600 l/rein)
brigade use (jlrst revision) 12796:1989 Specification for fire rake
6234: 986 Specification for portable fire 13039:1991 Code of practice for provision
extinguishers, water type (stored and maintenance of external
pressure) (first revision) hydrant system
8090: 992 Specification for couplings, 13385:1992 Specification for fire
branch pipe, nozzle, used in hose extinguisher 50 capacity wheel
reel tubing for fire fighting (first mounted water type (gas
revision) cartridge)

8096:1992 Specification for fire beaters 13386:1992 Specification for 50 litre capacity
(J%-strevision) fire extinguisher, mechanical
foam type
8149:1994 Functional requirements for twin
COZ fire extinguishers (trolley 13849:1993 Specification for portable fire
mounted) (jirst revision) extinguisher dry powder type
(constant pressure)
8423:1994 Specification for controlled
14609:1999 Specification for ABC dry
percolating hose for fire fighting
powder for fire fighting
@rst revision)
4933:2001 Specification for high pressure
8442:1977 Specification for stand post type
fire fighting hose
water monitor for fire fighting
4951:2001 Specification for fire
9972:1981 Specification for automatic
extinguisher, 135 litre capacity
sprinkler heads
mechanical foam type
10204:1982 Specification for portable fire
5051:2002 Specification for high pressure
extinguisher mechanical foam
fire hose delivery couplings
type
15105:2002 Design and installation of
10460:1983 Functional requirements for
fixed automatic sprinkler fire
small foam tender for fire extinguishing system
brigade use
15220:2002 Specification for halon 1211 and
10658:1999 Specification for higher capacity halon 1301 — Fire extinguishing
dry powder fire extinguisher media for fire protection
(trolley mounted)
15493:2004 Gaseous fire extinguishing
10993:1984 Functional requirements for systems — General requirements
2000 kg dry powder tender for
15497:2004 Specification for gaseous fire
fire brigade us extinguishing system — IG 01
11070: 984 Specification for bromo extinguishing system
chlorodifluoromethane (Halon- 15501:2004 Specification for gaseous fire
121 1) for fire fighting extinguishing system — IG 541
11101: 984 Specification for extended extitiguishing system
branch pipe for fire brigade 15505:2004 Gaseous fire extinguishing
use systems — HCFC blend A
11108:1984 Specification for portable fire extinguishing systems
extinguisher halon-1211 type 15506:2004 Specification for inert gaseous
11360:1985 Specification for smoke total fiie protection total flooding
detectors for use in automatic system — Argonite, IG 55
electrical fire alarm systems extinguishing system
11833:1986 Specification for dry powder 15517:2004 Gaseous fire extinguishing
fire extinguisher for metal SySkXIIS —HFC 227 (heptiUOrO
fires propane) extinguishing system

86 NATIONAL BUILDING CODE OF INDIA


Is No. Title IS No. Title
15519:2004 Code of practice for water mist ginning and pressing (includhg
fire protection systems — cotton seed delintering) factories
System design, installation and (jlrst revision)
commissioning 3034:1993 Code of practice for fire safety
15525:2004 Specification for gaseous fire of industrial buildings: Electrical
extinguishing system — IG 100 generating and distributing
extinguishing system stations (second revision)
15528:2004 Gaseous fire extinguishing 3058:1990 Code of practice for fire safety
systems — Carbon dioxide, total of industrial buildings: Viscose
flooding and local application rayon yarn andlor staple fibre
(sub-flour and in-cabinet), high plants (/irst revision)
and low pressure (refrigerated)
3079:1990 Code of practice for fire safety
systems
of industrial buildings: Cotton
(20) 2190:1992 Code of practice for selection, textile mills (first revision)
installation and maintenance
3594:1991 Code of practice for fire safety
of portable first-aid fire
of industrial buildings: General
extinguishers (third revision)
storage and warehousing
(21) 884:1985 Specification for first-aid hose including cold storage (first
reel for fiie fighting @st revision) revision)
15517:2004 Code of practice for inspection Code of practice for tire safety
3595:1984
and maintenance of gaseous fire of industrial buildings: Coal
extinguishing systems
pulverizers and associated
(22) 3034:1993 Code of practice for fire safety equipment (first revision)
of industrial buildings: Electrical
3836:2000 Code of practice for fire safety
generating and distributing
of industrial buildings: Jute
stations (second revision)
mills (second revision)
(23) 6382:1984 Code of practice for design and
4209:1987 Code of safety in chemical
installation of fixed carbon
laboratories @rst revision)
dioxide fire extinguishing
system (jirst revision) 4226:1988 Code of practice for fiie safety of
industrial buildings: AluminiumJ
(24) 14609:2001 Specification for dry powder for
Magnesium powder factories
fire fighting — Class ABC fires
(@t revision)
15493:2004 General requirement for
4886:1991 Code of practice for fire safety
commissioning of gaseous fire
of industrial buildings: Tea
extinguishing systems
factories (first revision)
(25) 13716:1993 Code of practice for fire safety
6329:2000 Code of practice for fire safety
in hotels
of industrial buildings: Saw
(26) 4963: 987 Recommendations for buildings
mills and wood works (first
and facilities for the physically
revision)
handicapped (first revision)
9109:2000 Co@e of practice for fire safety
(27) 4878: 986 Bye-laws for construction of
of industrial buildings: Paint and
cinema buildings (@st revision)
varnish factories
(28) 12456:1988 Code of practice for fire
11457 Code of practice for fire safety
protection of electronic data
(Part 1): 1985 of chemical industries: Part 1
processing installations
Rubber and plastic
(29) 1646:1997 Code of practice for fire safety
11460:1985 Code of practice for fwe safety of
of buildings (general) :
libraries and archives buildings
Electrical installations (second
revision) 12349:1988 Fire protection — Safety signs

2726:1988 Code of practice for fire safety 12407:1988 Graphic symbols for fire
of industrial buildings: Cotton protection plans

PART 4 FIRE AND LIFE SAFETY 87


NATIONAL BUILDING CODE OF INDIA
PART 5 BUILDING MATERIALS

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 MATERIALS ... 5
3 NEW OR ALTERNATIVE MATERIALS ... 5
4 THIRD PARTY CERTIFICATION ... 5
5 USED MATERIALS ... 5
6 STORAGE OF MATERIALS ... 5
7 METHODS OF TEST ... 5

LIST OF STANDARDS ... 6

NATIONAL BUILDING CODE OF INDIA


F—

National Building Code Sectional Committee, CED 46

FOREWORD

Ensuring the quality and effectiveness of building materials used in the construction and their storage are as
important as the other phases of building activity like planning, designing and constructing the building itself.
This Part, therefore, lists Indian Standards for materials used in building construction. The methods of tests, to
ensure the requirements demanded of the materials in the various situations, are also included.

Historically choice of building materials was determined by what was locally available, appropriateness to geo-
climatic conditions and affordability of users. In recent past, different initiatives have been taken in the areas of
research and development, standardization, and development and promotion of innovative materials. A review
of the recent trends indicates that the growth in the area of building materials covers emerging trends and latest
developments in the use of wastes, mineral admixtures in cement and concrete, substitutes to conventional timber,
composite materials and recycling of wastes, at the same time ensuring desired response of materials to fire, long
term performance and durability. In addition to these developments, the future decade may witness development
of specific materials which may be structured and designed to meet needs to specially developed construction
technologies, such as, for disaster prone areas or aggressive climatic and industrial situations.

In this context, the following factors have become important for facilitating application and adoption in practice,
of the materials:

a) Utilization of industrial, mining, mineral and agricultural wastes; plantation timbers; and renewable
natural fibres and residues for production of building materials.
b) Impact of production of building materials on the consumption levels of natural resources.
c) Change in energy demand in production of building materials due to development of efficient
manufacturing processes.
d) Impact of production and usage of materials and disposal thereof on the environment.

To encourage use of appropriate materials, it may be desirable to have, to the extent possible, performance
oriented approach for specifications rather than prescriptive approach. The approach has been already adopted in
some cases in development of standards, wherever found possible.
Indian Standards cover most of the requirements for materials in use. However, there may be a gap between
development of new materials and techniques of application and formulation of standards. It, therefore, becomes
necessary for a Building Code to be flexible to recognize building materials other tlmn those for which Indian
Standards are available. This Part, therefore, since its first version, duly takes care of this aspect and explicitly
provides for use of new or alternate building materials, provided it is proved by authentic tests that the new or
alternative material is effective and suitable for the purpose intended. However, it is worthwhile that more and
more emphasis is given to the satisfaction of performance requirements expected of a building material, so that
a wide range of such new or alternate materials can be evaluated and used, if found appropriate.
As already emphasized, quality of material is quite important for their appropriate usage, whether it is a material
for which an Indian Standard is available or a new or alternative material as defined in 3 of this Part. Third party
certification schemes available in the country for quality assurance of above materials can be used with advantage
to ensure the appropriateness of these materials.
This Part of the Code was first published in 1970 and subsequently revised in 1983. The first revision of this Part
incorporated an updated version of the list of Indian Standards given at the end of this Part of the Code. The
present draft revision of this Part, while basically retaining the structure of 1983 version of the Code, explicitly
takes care of the following:
a) While continuing to emphasize on conformity of building materials to available Indian Standards, the
building regulating authority also recognizes use of building materials conforming to other specifications
and test methods (see 3), in case Indian Standards are not available for particuhu materials.

PART 5 BUILDING MATERIALS 3


NATIONAL BUILDING CODE OF INDIA
PART 5 BUILDING MATERIALS

1 SCOPE component, laboratory/field tests, and field trials, as


required, and study of historical data are recommended.
This Part of the Code covers the requirements of building
materials and components, and criteria for accepting new 3.2 Approval in writing of the Authority or an agent
or alternative building materials and components. appointed by them for the purpose of approval of
material, shall be obtained by the owner or his agent
2 MATERIALS before any new, alternative or equivalent material is
Every material used in fulfillment of the requirements used. The Authority or their agent shall base such
of this Part, unless otherwise specified in the Code or approval on the principle set forth in 3.1 and shall
approved, shall conform to the relevant Indian Standards. require that tests be made (see 7.1) or sufficient
A list of Indian Standards as the ‘accepted standards’ is evidence or proof be submitted, at the expense of the
given at the end of this Part of the Code. At the time of owner or his agent, to substantiate any claim for the
publication of the Code, the editions indicated were proposed material.
valid. All standards are subject to amendments and NOTE — For interpretation of the term ‘Authority’ (fee
revisions. The Authority shall take cognizance of such also 7.1),the definitionof ‘Authorityhavingjurisdiction’given
in Part 2 ‘Administration’shatl apply.
amendments and revisions. The latest version of a
standa-d shall, as far as possible, be adopted at the time 4 THIRD PARTY CERTIFICATION
of enforcement of this Part of the Code.
For ensuring the conformity of materials for which
3 NEW OR ALTERNATIVE MATERIALS Indian Standards exist and for new or alternative
building materials, to requisite quality parameters the
3.1 The provisions of this Part are not intended to
services under the third party certification schemes of
prevent the use of any material not specifically
the Government, may be utilized with advantage.
prescribed under 2. Any such material maybe approved
by the Authority or an agency appointed by them for 5 USED MATERIALS
the purpose, provided it is established that the material
The use of used materials may not be precluded
is satisfactory for the purpose intended and the
provided these meet the requirements of this Part for
equivalent of that reqtired in this Part or any other new materials (see Part 2 ‘Administration’).
specification issued or approved by the Authority. The
Authority or an agency appointed by them shall take 6 STORAGE OF MATERIALS
into account the following parameters, as applicable
All building materials shall be stored on the building
to the concerned new or alternative building material:
site in such a way as to prevent deterioration or the
a) Requirements of the material specified/ loss or impairment of their structural and other essential
expected in terms of the provisions given in properties (see Part 7 ‘Constructional Practices and
the standards on its usage, including its Safety’ ).
applicability in gee-climatic condition;
7 METHODS OF TEST
b) General appearance;
c) Dimension and dimensional stability; 7.1 Every test of material required in this Part or by
the Authority shall be carried out in accordance with
d) Structural stability including strength properties;
the Indian Standard methods of test. In the case of
e) Fire safety;
methods of tests where Indian Standards are not
0 Durability; available, the same shall conform to the methods of
g) Thermal properties; tests issued by the Authority or their agent. A list of
h) Mechanical properties; Indian Standard methods of testis given at the end of
j) Acoustical properties; this Part of the Code as the ‘good practices’. Laboratory
k) Optical properties; tests shall be conducted by recognized laboratories
acceptable to the Authority.
m) Biological effect;
n) Environmental aspects; 7.1.1 The manufacturer/supplier shall satisfy himself
that materials conform to the requirements of the
P) Working characteristics;
specifications and if requested shall supply a certificate
@ Ease of handling; and
to this effect to the purchaser or his representative.
r) Consistency and workability. When such test certificates are not available, the
For establishing the performance of the material/ specimen of the material shall be tested.

PART 5 BUILDING MATERIALS 5


LIST OF STANDARDS

Following are the Indian Standards for various building 29. WIRE ROPES AND WIRE PRODUCTS
materials and components, to be complied with in
fulfillment of the requirements of the Code. 1. ALUMINIUM AND OTHER LIGHT METALS
L
AND THEIR ALLOYS
In the following list, while enlisting the Indian
Standards, the materials have been categorized in such 1S No. Title
a way as to make the list user friendly. In the process, 733:1983 Specification for wrought
if so required, some of the standards have been included aluminium and aluminium alloys,
even in more than one category of products, such as in bars, rods and sections for general
the category based on composition as well as on end engineering purposes (third
application of the materials. The list has been arranged revision)
in alphabetical order of their principal category as given
737:1986 Specification for wrought
below:
aluminium and alumiNum alloys,
1. ALUMINIUM AND OTHER LIGHT METALS sheet rods and strip for general
AND THEIR ALLOYS engineering purposes (third
2. BITUMEN AND TAR PRODUCTS revision)
3. BUILDER’S HARDWARES 738:1994 Specification for wrought
4. BUILDING CHEMICALS aluminium and aluminium alloy
drawn tube for general engineering
5. BUILDING LIME AND PRODUCTS
purposes (third revision)
6. BURNT CLAY PRODUCTS
740:1977 Specification for wrought
7. CEMENT AND CONCRETE (including concrete
aluminium and aluminium alloy
reinforcement)
rivet stock for general engineering
8. COMPOSITE MATRIX PRODUCTS (including purposes (second revision)
cement matrix products)
1254:1991 Specification for corrugated
9. CONDUCTORS AND CABLES
aluminium sheet (third revision)
10. DOORS, WINDOWS AND VENTILATORS
1284:1975 Wrought alurninium alloy bolt and
11. ELECTRICAL WIRING, FITTINGS AND screw stock for general engineering
ACCESSORIES purposes (second revision)
12. FILLERS, STOPPERS AND PU’ITIES
1285:2002 Specification for wrought
13. FLOOR COVERING, ROOFING AND OTHER aluminium and aluminium alloys,
FINISHES extruded round tube and hollow
14. GLASS sections for general engineering
15. GYPSUM BASED MATERIALS purposes (third revision)
16. LIGNOCELLULOSIC BUILDING MATERIALS 2479:1981 Colour code for the identification
(including timber, bamboo and products thereof) of aluminium and aluminium
17. PAINTS AND ALLIED PRODUCTS alloys for general engineering
18. POLYMERS, PLASTICS AND purposes (second revision)
GEOSYNTHETICS/GEOTEXTILES 2676:1981 Dimensions for wrought
19. SANITARY APPLIANCES AND WATER aluminium and aluminium alloy
FITTINGS sheet ,and strip
20. SOIL-BASED PRODUCTS 2677:1979 Dimensions for wrought
21. STEEL AND ITS ALLOYS aluminium and aluminium alloys,
plates and hot rolled sheets
22. STONES
14712:1999 Wrought aluminium and its alloys
23. STRUCTURAL SECTIONS
— Chequered/tread sheets for
24. THERMAL INSULATION MATERIALS
general engineering purposes —
25. THREADED FASTENERS AND RIVETS Specification
26. UNIT WEIGHTS OF BUILDING MATERIALS
27. WATERPROOFING AND DAMP-PROOFING 2. BITUMEN AND TAR PRODUCTS
MATERIALS 73:1992 Specification for paving bitumen
28. WELDING ELECTRODES AND WIRES (second revision)

6 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title
212:1983 Specification forcrude coaltarfor 1218:1978 Determination of phenols (first
general use (second revision) revision)
215:1995 Specification for road tar (third 1219:1978 Determination of naphthalene (@
revision) revision)
216:1961 Specification for coal tar pitch @-st 1220:1978 Determination of volatile matter
revision) content (first revision)
217:1988 Specification for cutback bitumen 3117:2004 Specification for bitumen emulsion
(second revision) for roads (anionic type) (first
218:1983 Specification for creosote oil for revision)
use as wood preservatives (second Specification for bitumen emulsion
8887:2004
revision)
for roads (cationic type) (second
454:1994 Specification for cutback bitumen revision)
from waxy crude (second revision)
9381:1979 Methods for testing tar and
702:1988 Specification for industrial bitumen bituminous materials: Determination
(second revision) of FRAASS breaking point of
l~ol to 1220 Methods for testing tar and bitumen
bituminous materials Methods for testing tar and
9382:1979
1201:1978 Sampling (first revision) bituminous materials: Determination
1202:1978 Determination of specific gravity of effect of heat and air by thin film ,.-
@rst revision) oven test
1203:1978 Determination of penetration @rst 10511:1983 Method for determination of
revision) asphaltenes in bitumen by
1204:1978 Determination of residue of precipitation with normal haptane
specified penetration (first revision) 10512:2003 Method for determination of wax
1205:1978 Determination of softening point content in bitumen (@t revision)
(jlrst revision) 13758 Coal tar pitch:
1206 Determination of viscosity: (Part 1) :1993 Determination of matter insoluble
(Part l):1978 Industrial viscosity (jirst revision) in quinoline
(Part2) :1978 Absolute viscosity @rst revision) (Part 2) :1993 Determination of coking value
(Part3) :1978 Kinematic viscosity @irst revision) 15172:2002 Methods for testing tar and
1~07: 1978 Determination of equiviscous bituminous materials —
temperature (EVT) @st revision) Determination of curing index for
cutback bitumens
1208:1978 Determination of ductility (first
revision) 15173:2002 Methods for testing tars and
bituminous materials —
1209:1978 Determination of flash point and
fire point (jirst revision) Determination of breaking point
for cationic bitumen emulsion
1210:1978 Float test (jirst revision)
15174:2002 Methods for testing tar and
1211:1978 Determination of water content
bituminous material —
(Dean and Stark method) (first
Deten+nation of breaking point
revision)
for anionic bitumen emulsion
1212:1978 Determination of loss of heating
15462:2004 Specification for polymer and
(first revision)
rubber modified bitumen
1213:1978 Distillation test (jirst revision)
1215:1978 Determination of matter insoluble 3. BUILDER’S HARDWARE
in toluene (first revision)
204 Specification for tower bolts:
1216:1978 Determination of volubility
(Part 1): 1991 Ferrous metals (&M revision)
in carbon disulphide or
trichloroethylene (/lrst revision) (Part 2) :1992 Non-femous metals (fifih revision)

1217:1978 Determination of mineral matter 205:1992 Specification for non-femous metal


(ASH) (jirst revision) butt hinges ~ow-th revision)

PART 5 BUILDING MATERIALS 7


1S No. Title 1S No. Title

206:1992 Specification for tee and strap 4992:1975 Specification for door handles for
hinges ~ourth revision) mortice locks (vertical type) (jirst
revision)
208:1996 Specification for door handles (fifih
revision) 5187:1972 Specification for flush bolts (jlrst
revision)
281:1991 Specification for mild steel sliding
door bolts for use with padlock 5899:1970 Specification for bathroom latches
(third revision) 5930:1970 Specification for mortice latch
Specificationforparliament hinges (vertical type)
362:1991
(jifth revision) 6315:1992 Specification for floor springs
(hydraulically regulated) for heavy
363:1993 Specification for hasps and staples
doors (second revision)
~otwth revision)
6318:1971 Specification for plastic window
364:1993 Specification for fanlight catch
stays and fasteners
(third revision)
6343:1982 Specification for door closers
452:1973 Specification for door springs, rat-
(pneumatically regulated) for light
tail type (second revision)
door weighing up to 40 kg (jirst
453:1993 Specification for double-acting revision)
spring liinges (third revision)
6607:1972 Specification for rebated mortice
729:1979 Specification for drawer locks, locks (vertical type)
cupboard locks and box locks
7196:1974 Specification for hold fast
(third revision)
7197:1974 Specification for double action
1019:1974 Specification for rim latches
floor springs (without oil check) for
(second revision)
heavy doors
1341:1992 Specification for steel butt hinges
7534:1985 Specification for sliding locking
(sixth revision)
bolts for use with padlocks (first
1823:1980 Specification for floor door revision)
stoppers (third revision)
7540:1974 Specification for mortice dead
1837: 1966 Specification for fanlight pivots locks
(first revision) Specification for ball catches for
8756:1978
2209:1976 Specification for mortice locks use in wooden almirah
(vertical type) (third revision) 8760:1978 Specification for mortice sliding
2681:1993 Specification for non-ferrous metal door locks, with lever mechanism
sliding door bolts for use with 9106:1979 Specification for rising butt hinges
padlocks (third revision)
9131:1979 Specification for rim locks
3564:1995 Specification for door closers
9460:1980 Specification for flush drop handle
(hydraulically regulated) (second
for drawer
revision)
9899:1981 Specification for hat coat and
3818:1992 Specification for continuous
wardrobe hooks
(piano) hinges (third revision)
10019:1981 Specification for mild steel stays
3828:1966 Specification for ventilator chains
and fi~teners
3843:1995 Specification for steel backflap
10090:1982 Specification for numerical
hinges (first revision)
10342:1982 Specification for curtain rail system
3847:1992 Specification for mortice night
latches (first revision) 12817:1997 Specification for stainless steel butt
hinges (jirst revision)
4621:1975 Specification for indicating bolts
for use in public baths and 12867:1989 Specification for PVC hand rails
lavatories (@t revision) covers
4948:2002 Specification for welded steel wire 14912:2001 Specification for door closers
fabric for general use (second concealed type (hydraulically
revision) regulated)

8 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title
4. BUILDING CHEMICALS 1508:1972 Specification for extenders for use
in synthetic resin adhesives (urea-
a) Anti-termite Chemicals
formaldehyde) for plywood (jlrst
632:1978 Specification for gamma-BHC revision)
(lindaue) emulsifiable concentrates 4835:1979 Specification for polyvinyl acetate
~ourth revision) dispersion-based adhesives for
8944:1978 Specification for chlorpyrifos wood (jlrst revision)
emulsifiable concentrates 9188:1979 Performance requirements for
adhesive for structural laminated
b) Chemical Admixture/Water Proofing Compounds
wood products for use under
2645:2003 Specification for integral exterior exposure condition
waterproofing compounds for Rubber based adhesives for fixing
12830:1989
cement mortar and concrete PVC tiles to cement
(second revision)
12994:1990 Epoxy adhesives, room tempera~e
6925:1973 Methods of test for determination
curing general purpose
of water soluble chlorides in
concrete admixtures 5. BUILDING LIME AND PRODUCTS
9103:1999 Specification for concrete
712:1984 Specification for building limes
admixtures (jirst revision)
(third revision)
c) Sealants/Fillers 1624:1986 Method of field testing of building
1834:1984 Specification for hot applied lime (first revision)
sealing compound for joint in 2686:1977 Specification for cinder as fine
concrete (jlrst revision) aggregates for use in lime concrete
1838 Specification for preformed fillers (@W revision)
for expansion joint in concrete 3068:1986 Specification for broken brick
pavements and structures (non- (burnt-clay) coarse aggregates for
extruding and resilient type): use in lime concrete (second
(Part 1): 983 Bitumen impregnated fibre (first revision)
revision) 3115:1992 Specification for lime based blocks
(Part 2): 984 CNSL aldehyde resin and coconut (second revision)
pith Specification for broken bricks
3182:1986
11433 Specification for one grade (burnt clay) fine aggregates for use
(Part 1): 1985 polysulphide based joint sealant: in lime mortar (second revision)
Part 1 General requirements 4098:1983 Specification for lime-pozzolana
12118 Specification for two parts mixture (jlrst revision)
polysulphide based sealants:
4139:1989 Specification for calcium silicate
(Part 1): 1987 General requirements bricks (second revision)
(Part 2) :1987 Methods of test Methodof tests for building limes:
6932
d) Adhesives (Part 1): 1973 Determination of insoluble residue,
loss on ignition, insoluble matter,
848:1974 Specification for synthetic resin silicon dioxide, ferric and
adhesives for plywood (phenolic
aluminium oxide, calcium oxide
and aminoplastic) @rst revision)
and magnesium oxide
849:1994 Specification for cold setting case
(Part 2): 1973 Determination of carbon dioxide
in glue for wood (first revision)
content
851:1978 Specification for synthetic resin
(Part 3): 1973 Determination of residue on
adhesives for construction work
slaking of quicklime
(non-structural) in wood (first
revision) (Part 4): 1973 Determination of fineness of
hydrated lime
852:1994 Specification for animal glue for
general wood-working purposes (Part 5): 1973 Determination of unhydrated
(second revision) oxide

PART 5 BUILDING MATERIALS 9


IS No. Title IS No. Title
(Part 6): 1973 Determination of volume yield of 6165:1992 Dimensions for special shapes of
quicklime clay bricks (first revision)
(Part 7): 1973 Determination of compressive and 11650:1991 Guide for manufacture of common
transverse strength burnt clay building bricks by semi-
(Part 8): 1973 Determination of workability mechanized process (jirst revision)

(Part 9): 1973 Determination of soundness 13757:1993 Specification for burnt clay fly ash
building bricks
(Part 10) :1973 Determination of popping and
pitting of hydrated lime d) Jallies
(Part 11) :1984 Determination of setting time of 7556:1988 Specification for burnt clay jallies
hydrated lime (jirst revision)
10360:1982 Specification for lime pozzolana
e) Tiles
concrete blocks for paving
10772:1983 Specification for quick setting lime 654:1992 Specification for clay roofing tiles,
pozzolana mixture Mangalore pattern (third revision)

12894:2002 Specification for pulverized fuel 1464:1992 Specification for clay ridge and
ash lime bricks (@t revision) ceiling tiles (second revision)
1478:1992 Specification for clay flooring tiles
6. BURNT CLAY PRODUCTS (second revision) .-

a) Blocks 2690 Specification for burnt clay flat


terracing tiles:
3952:1988 Specification for burnt hollow
(Part 1): 1993 Machine made (second revision)
bricks for walls and partitions
(second revision) (Part 2): 1992 Handmade (second revision)
3367:1993 Specification for burnt clay tiles for
b) Soil-Based Products
use in lining irrigation and drainage
1725:1982 Specification for soil-based blocks works (second revision)
used in general building construction 3951 Specification for hollow clay tiles
c) Bricks for floor and roofs:
(Part 1): 1975 Filler type (first revision)
1077:1992 Specification for common burnt
clay building bricks (f@ revision) (Part 2): 1975 Structural type (first revision)
2117:1991 Guide for manufacture of hand- 13317:1992 Specification for clay roofing
made-common burnt clay building camty tiles, half round and flat tiles
bricks (third revision)
7. CEMENT AND CONCRETE (including concrete
2180:1988 Specification for heavy duty burnt
reinforcement)
clay building bricks (third revision)
2222 1991 Specification for burnt clay a) Aggregates
perforated building bricks (Jourth 383:1970 Specification for coarse and fine
revision) aggregates from natural sources for
2691 1988 Specification for burnt clay facing concr,~e (second revision)
bricks (second revision) 1542:1992 Specification for sand for plaster
3495 Parts Methods of test of burnt clay (second revision)
1 to4) :1992 building bricks (third revision) 2116:1980 Specification for sand for masonry
3583:1988 Specification for burnt clay paving mortars (jirst revision)
bricks (second revision) 2386 Methods of test for aggregates for
4885:1988 Specification for sewer bricks @rst concrete:
revision) (Part 1): 1963 Particle size and shape
5454:1978 Methods for sampling of clay (Part 2): 1963 Estimation of deleterious materials
building bricks and organic impurities
5779:1986 Specification for burnt clay soling (Part 3): 1963 Specific gravity, density, voids,
bricks (first revision) absorption and bulking

10 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title
(Part 4): 1963 Mechanical properties 3812 Specification for pulverized fuel
(Part 5): 1963 Soundness ash:
(Part 6): 1963 Measuring mortar making properties (Part 1): 2003 For use as pozzolana in cement,
offine aggregates cement mortar and concrete
(Part 7): 1963 Alkali aggregate reactivity (second revision)

(Part 8): 1963 Petrographic examination (Part 2): 2003 For use as admixture in cement
mortar and concrete (second
2430:1986 Methods ofsampling ofaggregates
revision)
of concrete first revision)
6491:1972 Method of sampling of flyash
6579:1981 Specification for coarse aggregate
for water bound macadam (first 6925:1973 Methods of test for determination
revision) of water soluble chlorides in
concrete admixtures
9142:1979 Specification for artificial light-
weight aggregates for concrete 9103:1999 Specification for admixtures for
masonry units concrete (jirst revision)

b) Cement 12089:1987 Specification for granulated slag


for manufacture of Portland slag
269:1989 Specification for ordinary portland cement
cement, 33 Grade ~ow-th revision)
12870:1989 Methods of sampling calcined clay
455:1989 Specification for Portland slag pozzolana
cement (jlourth revision)
15388:2003 Specification for silica fume
1489 Specification for Portland
pozzolana cemenc d) Concrete

(Part 1): 1991 Flyash based (third revision) 456:2000 Code of practice for plain and
(Part 2): 1991 Calcined clay based (third revision) reinforced concrete (fourth
revision)
3466:1988 Specification for masonry cement
(second revision) 1343:1980 Code of practice for prestressed
6452:1989 Specification for high alumina concrete (jirst revision)
cement for structural use (first 4926:2003 Code of practice for ready-mixed
revision) concrete (third revision)
6909:1990 Specification for supersulphated e) Cement and Concrete Sampling and Methods of
cement Test
8041:1990 Specification for rapid hardening
516:1959 Methods of test for strength of
Portland cement (second revision)
concrete
8042:1989 Specification for white Portland
1199:1959 Methods of sampling and analysis
cement (second revision)
of concrete
8043:1991 Specification for hydrophobic
2770 Methods of testing bond in
Portland cement (second revision)
(Part 1): 1967 reinforced concrete: Part 1 Pullout
8112:1989 Specification for 43 grade ordinary
test
Portland ‘cement @rst revision)
3085:1965 Methods of test for permeability of
12269:1987 Specification for 53 grade ordinary
cement mortar and concrete
Portland cement
3535:1986 Methods of sampling hydraulic
12330:1988 Specification for sulphate resisting
cement (jirst revision)
Portland cement
4031 Methods of physical tests for
12600:1989 Specification for low heat Portland
hydraulic cementi
cement
(Part 1): 1996 Determination of fineness by dry
c) Mineral/Chemical Admixtures and Pozzolanas sieving (second revision)
1344:1981 Specification for calcined clay (Part 2): 1999 Determination of fineness by
pozzolana (second revision) specific surface by Blaine air
1727:1967 Methods of test for pozzolanic permeability method (second
materials @rst revision) revision)

PART .5 BUILDING MATERIALS 11


IS No. Title IS No. Title
(Part 3): 1988 Determination of soundness (jimt 12813:1989 Method of analysis of hydraulic
revision) cement by atomic absorption
(Part 4): 1988 Determination of consistency of spectrophotometer
standard cement paste (first 13311 Methods of non-destructive testing
revision) of concrete:
(Part 5): 1988 Determination of initial and final (Part 1) :1992 Ultrasonic pulse velocity
setting times (first revision) (Part 2): 1992 Rebound hammer
(Part 6): 1988 Determination of compressive
f) Treatment of Concrete Joints
strength of hydraulic cement (other
than masonry cement) (first 1834:1984 Specification for hot applied
revision) sealing compound for joint in
(Part 7): 1988 Determination of compressive concrete (jirst revision)
strength of masonry cement (&t 1838 Specification for preformed fillers
revision) for expansion joint in concrete
(Part 8): 1988 Determination of transverse and pavements and structures (non-
compressive strength of plastic extruding and resilient type):
mortar using prism (first revision) (Part 1): 1983 Bitumen impregnated fibre (Jirst
(Part 9): 1988 Determination of heat of hydration revision)
(first revision) (Part 2): 1984 CNSL aldehyde resin and coconut
(Part 10) :1988 Determination of drying shrinkage pith
first revision) 10566:1983 Methods of test for preformed
(Part 11): 1988 Determination of density (first fillers for expansion joints in
revision) concrete paving and structural
construction
(Part 12) :1988 Determination of air content of
hydraulic cement mortar (first 11433 Specification for one grade
revision) polysulphide based joint sealant
(Part 13) :1988 Measurement of water retentivity (Part 1): 1985 General requirements
of masonry cement (j?rst revision) (Part 2): 1986 Methods of test
(Part 14) :1989 Determination of false set 12118 Specification for two parts
(Part 15) :1991 Determination of fineness by wet polysulphide based sealants:
sieving (Part 1): 1987 General requirements
4032:1985 Methods of chemical analysis for (Part 2): 1987 Methods of test
hydraulic cement (jirst revision)
g) Concrete Reinforcement
5816:1999 Method of test for splitting
tensile strength of concrete @rst 432 Specification for mild steel and
revision) medium tensile steel bars and hard
drawn steel wire for concrete
8142: 976 Methods of test for determining
reinforcement:
setting time of concrete by
penetration resistance (Part 1): 1982 Mild steel and medium tensile steel
bars (third revision)
9013: 978 Method of making, curing and
determining compressive strength (Part 2): 1982 Hard drawn steel wire (third
of accelerated cured concrete test revision)
specimens 1566:1982 Specification for hard drawn steel
9284:1979 Method of test for abrasion wire fabric for concrete
resistance of concrete reinforcement (second revision)
12423:1988 Methods for colorometric analysis 1608:1995 Mechanical testing of materials —
of hydraulic cement Tensile testing
12803:1989 Methods of analysis of hydraulic 1785 Specification for plain hard
cement by X-ray fluorescence drawn steel wire for prestressed
spectrometer concrete:

12 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title

(Part 1): 1983 Cold drawn stress-relieved wire 6073:1971 Specification for autoclave
(second revision) reinforced cellular concrete floor
As drawn wire (first revision) and roof slabs
(Part 2): 1983
1786:1985 Specification for high strength 6441 Methods of test for autoclave
deformed steel bars and wires for cellular concrete products:
concrete reinforcement (third (Part 1): 1972 Determination of unit weight or
revision) bulk density and moisture content
2090:1983 Specification forhigh tensile steel (Part 2),; 1972 Determination of drying shrinkage
bars used inprestressed concrete (Part 4) ‘: 1972 Corrosion protection of steel
@rst revision) reinforcement in autoclave
6003:1983 Specification for indented wire cellular concrete
forprestressed concrete (first (Part 5): 1972 Determination of compressive
revision) strength
6006:1983 Specification for uncoated stress- (Part 6): 1973 Strength, deformation and cracking
relieved strand for prestressed of flexural members subject to
concrete @rst revision) bending-short duration loading test
10790 Methods of sampling of steel
(Part 7): 1973 Strength, deformation and cracking
forprestressed and reinforced -.
of flexural members subject to
concrete:
bending-sustained loading test
(Part 1): 1984 Prestressing steel
(Part 8): 1973 Loading tests for flexural members
(Part 2): 1984 Reinforcing steel in diagonal tension
13620:1993 Specification for fusion bonded (Part 9): 1973 Jointing of autoclave cellular
epoxy coated reinforcing bars concrete elements
14268:1995 Specification for uncoated stress 6523:1983 Specification for precast reinforced
relieved low relaxation seven ply concrete door and window frames
strand for prestressed concrete (first revision)
9872:1981 Specification for precast concrete
8. COMPOSITE MATRIX PRODUCTS
septic tanks
a) Cement Matrix Products
9893:1981 Specification for precast concrete
i) Precast Concrete Products blocks for lintels and sills

Specification for concrete masonry 12440:1988 Specification for precast concrete


2185
stone masonry blocks
units:
Hollow and solid concrete blocks 12592:2002 Specification for precast concrete
(Part l): 979
manhole covers and frames (jirst
(second revision)
revision)
(Part 2): 983 Hollow and solid lightweight
13356:1992 Specification for precast
concrete blocks (first revision)
ferrocement water tanks (250 to
(Part 3): 1984 Autoclave cellular (aerated) 10000 litres capacity)
concrete blocks @st revision)
13990:1994 Specification for precast reinforced
4996:1984 Specification for reinforced
concrete planks and joists for
concrete fence posts @st revision)
flooring and roofing
5751:1984 Specification for precast concrete 14143:1994 Specification for prefabricated
coping blocks (jirst revision) brick panel and partially precast
5758:1984 Specification for precast concrete concrete joist for flooring and
kerbs (jirst revision) rooting
5820:1970 Specification for precast concrete 14201:1994 Specification for precast reinforced
cable covers concrete channel unit for
6072:1971 specification for autoclave construction of floors and roofs
reinforced cellular concrete wall 14241:1994 Specification for precast L-Panel
slabs units for roofing

PART 5 BUILDING MATERIALS 13


‘T

1S No. Title IS No. Title


ii) Asbestos Fibre Cement Products 1916:1989 Specification for steel cylinder pipe
with concrete lining and coating
459:1992 Specification for corrugated and
(’jirst revision)
semi-corrugated asbestos cement
sheets (third revision) 3597:1998 Methods of test for concrete pipes
(second revision)
1592:2003 Specification for asbestos cement
pressure pipes and joints ~ourtlz 4350:1967 Specification for concrete porous
revision) pipes for under drainage
1626 Specification for asbestos cement 7319:1974 Specification for perforated
building pipes and pipe fittings, concrete pipes
gutters and gutter fittings and 7322:1985 Specification for specials for steel
roofing fittings: cylinder reinforced concrete pipes
(Part 1): 1994 Pipes and pipe fittings (~econd (iirst revision)
revision) 15155:2002 Specification for barlwire wrapped
(Part 2): 1994 Gutters and gutter fittings (second steel cylinder pipe with mortar
revision) lining and coating
*
(Part 3): 1994 Roofing fittings (second revision) b) Resin Matrix Products
2096:1992 Specification for asbestos cement
1998:1962 Methods of test for thermosetting
flat sheets @rst revision) .-
synthetic resin bonded laminated
2098:1997 Specification for asbestos cement sheets
building boards (first revision)
2036:1995 Specification for phenolic
5913:2003 Methods of test for asbestos cement
laminated sheets (second revision)
products (second revision)
2046:1995 Specification for decorative
6908:1991 Specification for asbestos cement
thermosetting synthetic resin
pipes and fittings for sewerage and
bonded laminated sheets (second
drainage (first revision)
revision)
7639:1975 Method of sampling asbestos
cement products 9. CONDUCTORS AND CABLES
9627:1980 Specification for asbestos cement
694:1990 Specification for PVC insulated ,
pressure pipes (light duty)
cables for working voltages up to
13000:1990 Silica-asbestos-cement flat sheets and including 1 100 V (third
— Specification revision)
13008:1990 Specification for shallow corrugated
1554 Specification for PVC insulated
asbestos cement sheets
(heavy duty) electric cables:
iii) Other Fibre Cement Products (Part 1): 1988 For working voltages up to and
14862:2000 Specification for fibre cement flat including 1 100 V (third revision)
sheets (Part 2): 1988 For working voltages from 3.3 kV
14871:2000 Specification for products in up tq and including 11 kV (second
fibre reinforced cement long revision)
corrugated or asymmetrical section 4289 Specification for flexible cables for
sheets and fittings for roofing and lifts mid other flexible:
cladding
(Part 1): 1984 Elastomer insulated cables ($irst
iv] Concrete Pipes and Pipes Lined/Coated with revision)
Concrete or Mortar (Part 2): 2000 PVC insulated circular cables
458:2003 Specification”#or precast concrete 7098 Specification for cross-linked
pipes (with and without w“~’ polyethylene insulated PVC
reinforcement) ~ourth revision) sheathed cables:
784:2001 Specification for prestressed (Part 1): 1988 For working voltage up to
concrete pipes (including specials) and including 1 100 V (second
(second revision) revision)

14 NATIONAL BUILDJNG CODE OF INDIA


Is No. Title IS No. Title

(Part 2): 1985 For working voltages from 3.3 kV (Part 24) :1984 Water soluble impurities test of
up to and including 33 kV (Jirst insulating paper
revision) (Part 25) :1984 Conductivity of water extract test
(Part 3): 1993 For working voltages from 66 kV of insulating paper
up to and including 220 kV (/irst (Part 26) :1984 pH value of water extract test of
revision) insulating paper
9968 Specification for elastomer- (Part 27) :1984 Ash content test of insulating
insulated cables: paper
(Part 1): 1988 For working voltages up to and (Part 28) :1984 Water absorption test (Electrical)
including 1 100 V (first revision) (Part 29) :1984 Environmental stress cracking test
(Part 2): 2002 For working voltages from 3.3 kV (Part 30) :1984 Hot set test
up to and including 33 kV (first
(Part 31) :1984 Oil resistance test
revision)
(Part 32) :1984 Carbon content test for polyethylene
10810 Methods of test for cables
(Part 33) :1984 Water absorption test (Gravimetric)
(Part O): 1984 General
(Part 34) :1984 Measurement of thickness of
(Part 1): 1984 Annealing test for wires used in metallic sheath
conductors .-
(Part 35) :1984 Determination of tin in lead alloy
(Part 2): 1984 Tensile test for aluminium wires for sheathing
(Part 3): 1984 Wrapping test for aluminium (Part 36) :1984 Dimensions of armounng material
wires
(Part 37) :1984 Tensile strength and elongation at
(Part 4): 1984 Persulphate test of conductor break of armouring materials
(Part 5): 1984 Conductor resistance test (Part 38) :1984 Torsion test on galvanized steel
(Part 6) :1984 Thickness of thermoplastic and wires for armouring
elastomeric insulation and sheath (Part 39) :1984 Winding test on galvanized steel
(Part 7): 1984 Tensile strength and elongation strips for armouring
at break of thermoplastic and (Part 40) :1984 Uniformity of zinc coating on steel
elastomeric insulation and sheath armour
(Part 8) :1984 Breaking strength and elongation (Part 41) :1984 Mass of zinc coating on steel
at break for impregnated paper armour
insulation (Part 42) :1984 Resistivity test of armour wires and
(Part 9): 1984 Tear resistance for paper insulation strips and conductance test of
(Part 10) :1984 Loss of mass test armour (wires/strips)

Thermal ageing in air (Part 43) :1984 Insulation resistance


(Part 11) :1984
Shrinkage test (Part 44) :1984 Spark test
(Part 12) :1984
(Part 45) :1984 High voltage test
(Part 13) :1984 Ozone resistance test
(Part 46) :1984 Partial discharge test
(Part 14) :1984 Heat shock test
(Part 47) :1984 Impuk& test
(Part 15) :1984 Hot deformation test
(Part 48) :1984 Dielectric power factor test
(Part 16) :1986 Accelerated ageing test by oxygen
pressure method (Part 49) :1984 Heating cycle test
(pd~ 17): 1986 Tear resistance test for heavy duty (Part 50) :1984 Bending test
sheath (Part 51) :1984 Dripping test
(Part 18) :1984 Colour fastness to day light (Part 52) :1984. Drainage test
(Part 19) :1984 Bleeding and blooming test (Part 53) :1984 Flammability test
(Part 20) :1984 Cold bend test (Part 54) :1984 Static flexibility test
(Part 21) :1984- Cold impact test (Part 55) :1986 Abrasion test
(Part 22) :1984 Vicat softening point (Part 56) :1987 Accelerated ageing by the air-
(Part 23) :1984 Melt-flow index pressure method

PART 5 BUILDING MATERIALS 15


IS No. Title IS No. Title
(Part 57) :1987 Flexing test (Part 6): 1998 Flexure test (third revision)
(Part 58) :1998 Oxygen index test (Part 7): 1998 Edge loading test (third revision)
(Part 59) :1988 Determination of the amount of (Part 8): 1998 Shock resistance test (third revision)
halogen acid gas evolved during (Part 9): 1998 Buckling resistance test (third
combustion of polymeric materials revision)
taken from cables
(Part 10) :1998 Slamming test (third revision)
(Part 60) :1988 Thermal stability of PVC insulation
(Part 11) :1998 Misuse test (third revision)
and sheath
(Part 12) :1998 Varying humidity test (third
(Part 61) :1988 Flame retardant test
revision)
(Part 62) :1993 Fire resistance test for bunched
(Part 13) :1998 End immersion test (third revision)
cables
(Part 63) :1993 Smoke density of electric cables (Part 14) :1998 Knife test (third revision)
under fire conditions (Part 15) :1998 Glue adhesion test (third revision)
(Part 64) :2003 Measurement of temperature index (Part 16) :1998 Screw withdrawal resistance test
12943:1990 Brass glands for PVC cables (third revision)
4021:1995 Specification for timber door,
10. DOORS, WINDOWS AND VENTILATORS window and ventilator frames
a) Wooden Doors, Windows and Ventilators 4962:1968 Specification for wooden side
sliding doors
1003 Specification for timber panelled
and glazed shutters: 6198:1992 Specification for ledged, braced
and battened timber shutters
(Part 1): 2003 Door shutters ~ourth revision)
(second revision)
(Part 2) :1994 Window and ventilator shutters
(third revision) b) Metal Doors, Windows Frames and Ventilators
1826:1961 Specification for venetian blinds 1038:1983 Specification for steel doors,
/
for windows windows and ventilators (third
2191 Specification for wooden flush revision)
door shutters (cellular and hollow 1361:1978 Specificatiori for steel windows
core type): for industrial buildings (first
(Part 1): 1983 Plywood face panels (fourth revision)
revision) 1948:1961 Specification for aluminium doors,
(Part 2): 1983 Particle board face panels and windows and ventilators
hardboard face panels (third 1949:1961 Specification for aluminium
revision) windows for industrial buildings
2202 Specification for wooden flush 4351:2003 Specification for steel door frames
door shutters (solid core type): (second revision)
(Part 1): 1991 Plywood face panels (jifth revision) 6248:1979 Specification for metal rolling
(Part 2): 1983 Particle board face panels and shutters and rolling grills ~irst
hardboard face panels (third revision?
revision) 7452:1990 Specification for hot rolled steel
4020 Method of tests for door shutters: sections for doors, windows and
ventilators (second revision)
(Part 1): 1998 General (third revision)
10451:1983 Specification for steel sliding
(Part 2): 1998 Measurement of dimensions and
shutters (top hung type)
squareness @bird revision)
10521:1983 Specification for collapsible gates
(Part 3): 1998 Measurement of general flatness
(third revision) c) Plastic Doors and Windows
(Part 4): 1998 Local planeness test (third revision) 14856:2000 Specification for glass fibre
(Part 5): 1998 Impact indentation test (third reinforced (GRP) panel type door
revision) shutters for internal use

16 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title
15380:2003 Specification formoulded raised 2215:1983 Specification for starters for
high density fibre (HDF) panel fluorescent lamps (third revision)
doors 2412:1975 Specification for link clips for
electrical wiring @W rev;sion)
11. ELECTRICAL WIRING FITTINGS AND
ACCESSORIES 2418 Specification for tubular
fluorescent lamps for general
371:1999 Specification for ceiling roses
lighting services:
(third revision)
(Part 1): 1977 Requirements and tests (first
374:1979 Specification for electric ceiling
revision)
type fans and regulators (third
revision) (Part 2): 1977 Standard lamp data sheets (first
revision)
418:1978 Specification for tungsten filament
general service electric lamps (Part 3): 1977 Dimensions of G-5 and G-13 bi-
(third revision) pin caps @_st revision)
1258:1987 Specification for bayonet lamp (Part 4): 1977 Go and no-go gauges for G-5 and
holders (third revision) G-13 hi-pin caps (&st revision)
1293:1988 Specification for plugs and socket- 2667: 988 Specification for fittings for rigid
outlets rated voltage up to and steel conduits for electrical wiring
including 250 V and rated current (second revision) -.
up to and including 16 amperes
2675: 983 Specification for enclosed
(second revision)
distribution fuseboards and cutouts
1534 Specification for ballasts for for voltages not exceeding 1000 V
(Part 1): 1977 fluorescent lamps: Part 1 For (second revision)
switch start circuits (second 3287:1965 Specification for industrial lighting
revision)
fittings with plastic reflectors
1554 PVC insulated (heavy duty) electric
3323:1980 Specification for hi-pin lamp
cables:
holders for tubular fluorescent
(Part 1): 1988 For working voltages upto and lamps (&t revision)
including 1 100 V (third revision)
3324:1982 Specification for holders for
(Part 2): 1988 For working voltages from 3.3 kV starters for tubular fluorescent
upto and including 11 kV (second lamps (jirst revision)
revision)
3419:1989 Specification for fittings for rigid
1777:1978 Specification for industrial
non-metallic conduits (second
luminaire with metal reflectors
revision)
(jirst revision)
3480:1966 Specification for flexible steel
2086:1993 Specification for carriers and bases
conduits for electrical wiring
used in re-wirable type electric
fuses up to 650 V (third revision) 3528:1966 Specification for waterproof
electric lighting fittings
2148:2004 Specification for flameproof
enclosures “d” for electrical 3553:1966 Specification for watertight electric
apparatus for explosive gas lighting fittings
atmospheres (third revision) 3837:1976 Specification for accessories for
2206 Specification for flameproof rigid steel conduits for electrical
electric lighting fittings: wiring (jirst revision)
(Part 1): 1984 Well glass and bulkhead types (first 3854:1997 Specification for switches for
revision) domestic and similar purposes
(Part 2): 1976 Fittings using glass tubes (second revision)
(Part 3): 1989 Fittings using fluorescent lamps 4012:1967 Specification for dust-proof
and plastic covers electric lighting fittings
(Part 4): 1987 Portable flame-proof handlamps 4013:1967 Specification for dust-tight electric
and approved flexible cables lighting fittings

PART 5 BUILDING MATERIALS 17


r-

1S No. Title IS No. Title

4160:1967 Specification for interlocking (Part 5/See 5): Particular requirements, Section 5
switch socket outlet 1987 Flood light
4615:1968 Specification for switch socket 11037:1984 Electronic type fan regulators
outlets (non-interlocking type) 13010:2002 AC watt-hour meters, Class 0.5, 1
4649:1968 Specification for adaptors for and 2 (jirst revision)
flexible steel conduits 13779:1999 AC static watthour meters (Class 1
5077:1969 Specification for decorative and 2) (jirst revision)
lighting outfits 13947 Specification for low-voltage
6538:1971 Specification for three-pin plugs (Part 3): 1993 switchgear and controlgear: Part 3
made of resilient material Switches, disconnectors, switch
disconnectors and fuse
8030:1976 Specification for luminaires for
combination units
hospitals
14763:2000 Conduit for electrical purposes,
8828:1996 Specification for circuit-breakers
outside diameters of conduits for
for over current protection for
electrical installations and threads
household and similar installation
for conduits and fittings
(second revision)
14768 Conduit fittings for electrical
9537 Specification for conduits for
installations:
electrical installations: F- -
(Part 1): 2000 General requirements
(Part 1): 1980 General requirements
(Part 2): 2003 Metal conduit fittings
(Part 2): 1981 Rigid steel conduits
14772:2000 Enclosures for accessories for
(Part 3): 1983 Rigid plain conduits for insulating household and similar fixed
materials electrical installations
(Part 4) :1983 Pliable self-recovering conduits for 14927 Cable trunking and ducting
insulating materials systems for electrical installations
(Part 5) :2000 Pliable conduits of insulating (Part 1): 2001 General requirements
materials
(Part 2): 2001 Cable trunking and ducting
(Part 6) :2000 Pliable conduits of metal or systems intended for mounting on
composite materials walls or ceilings
(Part 8): 2003 Rigid non-threadable conduits of 14930 Conduit systems for electrical
aluminium alloy installations:
9926:1981 Specification for fuse wires used in (Part 1): 2001 General requirements
rewirable type electric fuses up to
(Part 2): 2001 Particular requirements for conduit
650 V
system buried underground
10322 Specification for luminaires:
15368:2003 Cable reels for household and
(Part 1): 1982 General requirements similar purposes
(Part 2): 1982 Constructional requirements
12. FILLERS, STOPPERS AND PUTTIES
(Part 3): 1984 Screw and screwless terminations
110:1983 Spec&ication for ready mixed
(Part 4): 1984 Methods of tests
paint: brushing, grey filler, for
(Part 5/See 1) : Particular requirements, Section 1
enamels, for use over primers (jirst
1985 General purpose lurninaires
revision)
(Part 5/See 2): Particular requirements, Section 2
419:1967 Specification for putty for use on
1985 Recessed luminaires
window frames @rst revision)
(Part 5/See 3) : Particular requirements, Section 3
423:1961 Specification for plastic wood, for
1987 Luminaires for road and street
joiner’s filler (revised)
lighting
3709:1966 Specification for mastic cement for
(Part 5/See 4): Particular requirements, Section 4
bedding of metal windows
1987 Portable general purpose
luminaires 7164:1973 Specification for stopper

18 NATIONAL BUILDING CODE OF INDIA


IS No. Title 1S No. Title

13184:1991 Specification for mastic filler, heavy hydrocarbon products like


epoxy based kerosene, diesel and furnace oil

13. FLOOR COVERING, ROOFING AND OTHER f) Plastic Flooring


FINISHES 3461:1980 Specification for PVC asbestos
floor tiles (first revision)
a) Concrete Flooring
3462:1986 Specification for unbacked flexible
1237:1980 Specification for cement concrete
PVC flooring (second revision)
flooring tiles (/irst revision)
3464:1986 Methods of test for plastic flooring
13801:1993 Specification for chequered cement
and wall tiles (second revision)
concrete tiles
g) CeramicNitreous
b) Flooring Compositions
2333:1992 Specification for plaster of Paris for
657:1982 Specification for materials for use
ceramic industry (second revision)
in the manufacture of magnesium
oxychloride flooring compositions 4457:1982 Specification for ceramic unglazed
(second revision) vitreous acid resisting tile (Jirst
revision)
9162:1979 Methods of tests for epoxy resin,
hardeners and epoxy resin 13630 Method of test for ceramic tiles:
composition for floor topping (Part 1): 1993 Determination of dimensions and
surface quality
9197:1979 Specification for epoxy resin,
hardness and epoxy resin (Part 2): 1992 Determination of water absorption
compositions for floor topping (Part 3): 1992 Determination of moisture
10132:1982 Method of test for materials expansion using boiling water —
for use in the preparation of Unglazed tiles
magnesium oxychloride flooring (Part 4): 1992 Determination of linear thermal
composition expansion

c) Linoleum Flooring (Part 5): 1992 Determination of resistance to


thermal shock
653:1992 Specification for linoleum sheets
(Part 6): 1993 Determination of modulus of rupture
and tiles (third revision)
(Part 7): 1993 Determination of chemical mistance
9704:1980 Methods of tests for linoleum
— Unglazed tiles
sheets and tiles
(Part 8): 1993 Determination of chemical resistance
d) Rubber Flooring — Glazed tiles
809:1992 Specification for rubber flooring (Part 9): 1993 Determination of crazing resistance
materials for general purposes — Glazed tiles
(second revision) (Part 10) :1993 Determination of frost resistance
e) Bituminous Flooring (Part 11) :1993 Determination of resistance to
surface abrasion — Glazed tiles
1195:2002 Specification for bitumen mastic
(Part 12) :1993 Deter@nation of resistance to deep
for flooring (third revision)
abrasion — Unglazed tiles
8374:1977 Specification for bitumen mastic,
. (Part 13) :1993 Determination of scratch hardness
anti-static and electrically
conducting grade of surface according to Mobs’

9510:1980 Specification for bitumen mastic 13711:1993 Sampling and basis for acceptance
acid resisting grade of ceramic tiles
13026:1991 Specification for bitumen mastic 13753:1993 Specification for dust pressed
for flooring for industries handling ceramic tiles with water absorption
LPG and other light hydrocarbon of E > 10% Group (B 111)
products 13754:1993 Specification for dust pressed
15194:2002 Specification for pitch-mastic ceramic tiles with water absorption
flooring for industries handling of 6% < E < 10% Group (B II b)

PART 5 BUILDING MATERIALS 19


IS No. Title L’SNo. Title
13755:1993 Specification for dust pressed 13317:1992 Specification for clay roofing
ceramic tiles with water absorption camty tiles, half round and flat
of 3% < E < 6% Group (B II a) tiles
13756:1993 Specification for dust pressed k) Wall Coverings/Fhishing
ceramic tiles with water absorption
of E < 3% Group B I 1542:1992 Specification for sand for plaster
(second revision)
h) Other Floorings
4456 Methods of test for chemical
4456 Methods of test for chemical resistant mortars:
resistant mortars: (Part 1): 1967 Silicate type and resin type
(Part 1): 1967 Silicate type and resin type (Part 2): 1967 Sulphur type
(Part 2): 1967 Sulphur type 4832 Specification for chemical resistant
4457:1982 Specification for ceramic unglazed mortars:
vitreous acid resisting tile (first (Part 1): 1969 Silicate type
revision) (Part 2): 1969 Resin type
4832 Specification for chemical resistant (Part 3): 1968 Sulphur type
mortars:
15418:2003 Specification for finished wall
(Part 1) :1969 Silicate type papers, wall vinyls and plastic wall
~-
(Part 2): 1969 Resin type coverings in roll form
)!.
(Part 3) :1968 Sulphur type v
14. GLASS
4860:1968 Specification for acid resistant
bricks 2553 Specification for safety glass:
(Part 1): 1990 Part 1 General purpose (third
j) Roofing revision) ,
,,,
,~,,
277:1992 Specification for galvanized steel 2835:1987 Specification for flat transparent 1:
If.
7fi
sheets (plain and corrugated (@h sheet glass (third revision) ,,

revision) 3438:1994 Specification for silvered glass


459:1992 Specification for corrugated and mirrors for general purposes .1
j,>
semi-comugated asbestos cement (second revision) ~
sheets (third revision) 5437:1994 Specification for figured rolled and
654:1992 Specification for clay roofing tiles, wired glass (first revision)
Mangalore pattern (third revision) 14900:2000 Specification for transparent float
1464:1992 Specification for clay ridge and glass .,
*.
ceiling tiles (second revision)
15. GYPSUM BASED MATERIALS
2690 Specification for burnt clay flat
terracing tiles: 2095 Specification for gypsum plaster
Machine made (second revision) boards:
(Part 1): 1993
(Part 2): 1992 Hand-made (second revision) (Part 1): 1996 Plain gypsum plaster boards

3951 Specification for hollow clay tiles (Part 2): 2001 Coated/laminated gypsum plaster
for floor and roofs: boards ,.*-
(Part 3): 1996 Reinforced gypsum plaste~boards {
(Part 1): 1975 Filler type t&st revision) $
(second revision)
(Part 2): 1975 Structural type (/irst revision) I
2542 Methods of test for gypsum plaster,
10388:1982 Specification for corrugated coir
wood wool cement roofing sheets concrete and products:
~
12583:1988 Specification for corrugated (Part l/See 1): Plaster and concrete, Section 1 .
bitumen roofing sheets 1978 Normal consistency of gypsum
plaster (first revision)
12866:1989 Specification for plastic translucent
sheets made from thermosetting (Part l/see 2): Plaster and concrete, Section 2 I
polyester resin (glass fibre 1978 Normal consistency of gypsum :
reinforced) concrete (fwst revision)

20 NATIONAL BUILDING CODE OF INDIA


IS No, Title 1S No. Title
(Part l/See 3): Plaster and concrete, Section 3 (Part 1): 1976 Excluding premixed lightweight
1978 Setting time of plaster and concrete plaster (jlrst revision)
~rst revision) (Part 2): 1976 Premixed lightweight plaster @rst
(Part l/See 4) : Plaster and concrete, Section 4 revision)
1978 Transverse strength of gypsum 2849:1983 Specification for non-load bearing
plastey (j%st revision)
gypsum partition blocks (solid and
(Part l/See 5): Plaster and concrete, Section 5 hollow types)
1978 Compressive strength and dry set
8272:1984 Specification for gypsum plaster or
density of gypsum plaster (first
use in the manufacture of tlbrous
revision)
plasterboards (jirst revision)
(Part l/See 6) : Plaster and concrete, Section 6
9498:1980 Specification for inorganic
1978 Soundness of gypsum plaster tjirst
aggregates for use in gypsum
revision)
plaster
(Part l/See 7) : Plaster and concrete, Section 7
1978 Mechanical resistance of gypsum 16. LIGNOCELLULOSIC BUILDING
plaster by dropping ball test oirst MATERIALS
revision)
a) Timber and Bamboo
(Part l/See 8) : Plaster and concrete, Section 8
1978 Freedom from coarse particles i) Timber ClassZ~cation
tjlrst revision) 399:1963 Classification of commercial
(Pak l/See 9) : Plaster and concrete, Section 9 timbers and their zonal distribution
1978 Expansion of plaster (first revision) (revised)
(Part l/See 10) : Plaster and concrete, Section 10 1150:2000 Trade names and abbreviated
1978 Sand in set plaster (first revision) symbols for timber species (third
(Part l/See 11) : Plaster and concrete, Section 11 revision)
1978 Wood fibre content in gypsum 4970:1973 Key for identification of commercial
plaster (first revision) timber @rst revision)
(Part l/See 12) : Plaster and concrete, Section 12
ii) Timber Conversion and Grading
1978 Dry bulk density @rst revision)
(Part 2/See 1): Gypsum products, Section 1 190:1991 Specification for coniferous sawn
1981 Measurement of dimensions @-st timber (baulks and scantlings)
revision) ~ourth revision)

(Part 2/See 2): Gypsum products, Section 2 1326:1992 Specification for non-coniferous
1981 Determination of mass (first sawn timber (baulks and scantlings)
revision) (second revision)

(Part 2/See 3): Gypsum products, Section 3 1331:1971 Specification for cut sizes of timber
1981 Determination of mass and thickness (second revision)
of paper surfacing (first revision) 3337:1978 Specification for ballies for general
(Part 2/See 4): Gypsum products, Section 4 purposes (first revision)
1981 Transverse strength (j$rst revision) 5966:1993 Specification for non-coniferous
(Part 2/See 5) : timber in converted form for
Gypsum products, Section 5
general purpose (first revision)
1981 Compressive strength (@t revision)
14960:2001 Specification for preservative
(Part 2/See 6): Gypsum products, Section 6
treated and seasoned sawn timber
1981 Water absorption (jirst revision)
from rubberwood (Hevea
(Part 2/See 7) : Gypsum products: Section 7 brasiliensis)
1981 Moisture content @irst revision)
iii) Timber Testing
(Part 2/See 8) : Gypsum products, Section 8
1981 Nail retention of precast reinforced 1708 Methods of testing small clear
gypsum slabs (/irst revision) specimens of timber:
2547 Specification for gypsum building (Part 1) :1986 Determination of moisture content
plaster: (second revision)

PART 5 BUILDING MATERIALS 21


r
IS No. Title IS No. Title
(Part 2): 1986 Determination of specific gravity (Part 1): 991 Determination of copper, arsenic,
(second revision) chromium, zinc, boron, creosote
Determination of volumetric and fuel oil (&t revision)
(Part 3): 1986
shrinkage (second revision) (Part 2): 991 Determination of copper (in copper
Determination of radial and organic preservative salt) and
(Part 4): 1986
pentachlorophenol (jirst revision)
tangential shrinkage and fibre
saturation point (second revision) 4907:1968 Method of testing timber connectors
(Part 5): 1986 Determination of static bending 8292:1992 Methods for evaluation of working

1
strength (second revision) quality of timber under different
wood operations — Method of test
(Part 6) : 986 Determination of static bending
(/irst revision)
strength under two point loading
(second revision) 8720:1978 Methods of sampling of timber
scantlings from depots and their
(Part 7): 986 Determination of impact bending
conversion for testing
strength (second revision)
8745:1994 Methods of presentation of data of
(Part 8): 1986 Determination of compressive
physical and mechanical properties
strength parallel to grain (second
of timber (jirst revision)
revision)
10420:1982 Method of determination of sound
(Part 9): 1986 Determination of compressive 1’
..-.
absorption coefilcient of timber by
strength perpendicular to grain
standing wave method .
(second revision)
10754:1983 Method of determination of thermal
(Part 10) :1986 Determination of hardness under
conductivity of timber
static indentation (second revision )
11215:1991 Methods for determination of
(Part 11) :1986 Determination of shear strength
moisture content of timber and
parallel to grain (second revision)
timber products (/irst revision)
(Part 12) :1986 Determination of tensile strength
13621:1993 Method of test for determination of
parallel to grain (second revision)
dielectric constant of wood under
(Part 13) :1986 Determination of tensile strength microwave frequencies
perpendicular to grain (second
iv) Structural Timber and Test
revision)
(Part 14) :1986 Determination of cleavage strength 3629:1986 Specification for structural timber
parrdlel to grain (second revision) in building @rst revision)
(Part 15) :1986 Determination of nail and screw 4891:1988 Specification for preferred cut sizes
holding power (second revision) of structural timber (fzrst revision)
(Part 16) :1986 Determination of brittleness by 4924 Method of test for nail jointed
izod impact (second revision) timber trusses:
(Part 17) :1986 Determination of brittleness by (Part 1): 1968 Destructive test
Charpy impact (second revision) (Part 2): 1968 Proof test
(Part 18) :1986 Determination of torsional strength v) Logs
(second revision)
3364 Method of measurement and
1900:1974 Method of testing wood poles @rst
evaluation of defects in timber:
revision)
(Part 1): 1976 Logs (first revision)
2408:1963 Methods of static tests of timbers
in structural sizes (Part 2) :1976 Converted timber Qlrst revision)

2455:1990 Method of sampling of model trees 4895:1985 Specification for teak logs (first
and logs for timber testing and their revision)
conversion (second revision) 5246:2000 Specification for coniferous logs
2753 (/irst revision)
Methods for estimation of
preservatives in treated timber and 7308:1999 Specification for non-coniferous
treating solutions: logs (/irst revision)

22 NATIONAL BUILDING CODE OF JNDIA


IS No. Title IS No. ●
Title
vi) Bamboo (Part 20) :1983 Acidity and alkalinity resistance
test (second revision)
6874:1973 Method of tests for round bamboos
4990:1993 Specification for plywood for
8242:1976 Methods of tests for split bamboos
concrete shattering work (second
b) Reconstituted Products revision)
5509:2000 Specification for fire retardant
i) Plywood
plywood (second revision)
303:1989 Specification for plywood for 5539:1969 Specification for preservative
general purposes (third revision) treated plywood
1328:1996 Specification for veneered for decorative
316:1974 Specification
decorative plywood (third revision) plywood using plurality of veneers
1734 Method of test for plywood: for decorative faces
(Part 1): 1983 Determination of density and 0701:1983 Specification for structural plywood
moisture content (second revision) Specification for metal faced
3957:1994
(Part 2): 1983 Determination of resistance of dry plywood
heat (second revision)
(Part 3): 1983 Determination of fire resistance ii) Blackboards, Particle Boards and Fibre Boards
(second revision) 1658:1977 Specification for fibre hardboards
(Part 4) :1983 Determination of glue shear strength (second revision)
(second revision) 1659:1990 Specification for block boards
(Part 5): 1983 Test for adhesion of plies (second (third revision)
revision) 2380 Methods of test for wood particle
(Part 6): 1983 Determination of water resistance boards and boards from other
(second revision) lignocellulosic materials:
(Part 7): 1983 Mycological test (second revision) (Part 1): 1977 Preparation and conditioning of
(Part 8): 1983 Determination ofpH value (second test specimens (jirst revision)
revision) (Part 2) :1977 Accuracy of dimensions of boards
(Part 9): 1983 Determination of tensile strength (jlrst revision)
(second revision) (Part 3): 1977 Determination of moisture content
(Part 10:1983 Determination of compressive and density (first revision)
strength (second revision) (Part 4): 1977 Determination of static bending
(Part 11) :1983 Determination of static bending strength (first revision)
strength (second revision) (Part 5): 1977 Determination of tensile strength
(Part 12) : ~983 Determination of scarf joint perpendicular to surface (first
strength (second revision) revision)
(Part 13) :1983 Determination of panel shear (Part 6): 1977 Determination of tensile strength
strength (second revision) parallel to surface (jirst revision)
(Part 14) :1983 Determination of plate shear (Part 7): 1977 Determination of compression —
strength (second revision) Perpend@dar to plane of the board
(Part 15) :1983 Central loading of plate test (first retision)
(second revision) (Part 8): 1977 Compression parallel to surface
(Part 16) :1983 Vibration of plywood plate test test (jlrst revision)
(second revision) (Part 9): 1977 Determination of resistance to
(Part 17) :1983 Long time loading test of plywood shear in plane of the board (jirst
strips (second revision) revision)

(Part 18) :1983 Impact resistance test on the (Part 10) :1977 Falling hammer impact test @rst
surface of plywood (second revision)
revision) (Part 11) :1977 Surface hardness (@t revision)
(Part 19) :1983 Determination of nails and screws (Part 12) :1977 Central loading of plate test (j%
holding power (second revision) revision)

PART 5 BUILDING MATERIALS 23


T--”

IS No. Title IS No. Title

(Part 13) :1977 Long time loading bending test iii) Wood-Based Laminates
@rst revision)
3513 (Part3) : Specification for resin treated
(Part 14) :1977 Screw and nail withdrawal test 1989 compressed wood laminates
@rst revision) (compregs): Part 3 For general
(Part 15) :1977 Lateral nail resistance (’first purposes (fzrst revision)
revision) 3513 (Part 4): Specification for high and medium
(Part 16) :1977 Determination of water absorption 1966 density wood laminates (compreg):
@rst revision) Part 4 Sampling and tests

Determination of swelling in water 7638:1998 Methods of sampling for woodl


(Part 17) :1977
lignocelhdosic based panel products
(first revision)
9307 Methods of tests for wood-based
(Part 18) :1977 Determination of mass and
structural sandwich construction:
dimensional changes caused by
moisture changes (jirst revision) (Part 1): 1979 Flexure test

(Part 19) :1977 Durability cyclic test for interior (Part 2): 1979 Edgewise compression test
use (jirst revision) (Part 3): 1979 Flatwise compression test
(Part 20) :1977 Accelerated weathering cyclic test (Part 4): 1979 Shear test
for exterior use (/irst revision) (Part 5): 1979 Flatwise tension test
(Pm 21) :1977 Planeness test under uniform (Part 6): 1979 Flexure creep test
moisture content @rst revision) (Part 7): 1979 Cantilever vibration test
(Part 22) :1981 Determination of surface glueability (Part 8): 1979 Weathering test
test
14315:1995 Specification for commercial
(Part 23) :1981 Vibration test for particle boards veneers
3087:1985 Specification for wood particle 14616:1999 Specification for laminated veneer
boards (medium density) for lumber
general purposes @rst revision)
iv) Bamboo and Coir Board Products
3097:1980 Specification for veneered particle
boards (first revision) 13958:1994 Specification for bamboo mat
3129:1985 Specification for low density board for general purposes
particle board (jirst revision) 14588:1999 Specification for bamboo mat
veneer composite for general
3308:1981 Specification for wood wool
purposes
building slabs (’@t revision)
14842:2000 Specification for coir veneer board
3348:1965 Specification for fibre insulation
for general purposes
boards
15476:2004 Specification for bamboo and
3478:1966 Specification for high density
corrugated sheets
wood particle boards
12406:2003 Specification for medium density v) Adhesives
fibreboards for general purposes 848:1974 Specification for synthetic resin
(first revision) adhesives for plywood (phenolic
12823:1990 Specification for prelaminated and aminoplastic) (fzrst revision)
particle boards 849:1994 Specification for cold setting case
13745:1993 Method for determination of in glue for wood (first revision)
formaldehyde content in particle 851:1978 Specification for synthetic resin
board by extraction method called adhesives for construction work
perforator method (non-structural) in wood (first
14276:1995 Specification for cement bonded revision)
particle boards 852:1994 Specification for animal glue for
14587:1998 Specification for prelaminated general wood-working purposes
medium density fibre board (second revision)

24 NATIONAL BUILDING CODE OF INDIA


Is No. Title IS No. Title
1508:1972 Specification for extenders for use (Part l/See 7): Test on liquid paints (general and
in synthetic resin adhesives (urea- 1987 physical), Section 7 Mass per
formaldehyde) forplywood@r,st 10 Iitres (third revision)
revision) (Part 2/See 1): Test on liquid paints (chemical
4835:1979 Specification for polyvinyl acetate 1988 examination), Section 1 Water
dispersion-based adhesives for content (third revision)
wood first revision) (Part 2/See 2): Test on liquid paints (chemical
9188:1979 Performance requirements for 1986 examination), Section 2 Volatile
adhesive for structural laminated matter (third revision)
wood products for use under (Part 3/See 1): Tests on paint film formation,
exterior exposure condition
1986 Section 1 Drying time (third
revision)
17. PAINTS AND ALLIED PRODUCTS
(Part 3/See 2): Tests on paint film formation,
a) Water Based Paints and Pigments
1989 Section 2 Film thickness (third
427:1965 Specification for distemper, dry, revision)
colouras required (revised) (Part 3/See 4): Tests on paint film formation,
428:2000 Specification for distemper, 1987 Section 4 Finish (third revision)
washable (second revision) (Part 3/See 5): Tests on paint film formation, --
5410:1992 Specification for cement paint, 1987 Section 5 Fineness of grind (third
colour as required (’jirst revision) revision)
5411 Specification for plastic emulsion (Part 4/See 1): Optical test, Section 1 Opacity
paint: 1988 (third revision)
(Part 1):1974 Forinterior use@rst revision) (Part 4/See 2): Optical test, Section 2 Colour
(Part 2): 1972 For exterior use 1989 (third revision)
(Part 4/See 3): Optical test, Section 3 Light
b) Ready Mixed Paints, Enamels and Powder
1988 fastness test (third revision)
Coatings
(Part 4/See 4): Optical test, Section 4 Gloss (third
101 Methods of sampling and test for 1986 revision)
paints, varnishes and related
(Part 5/See 1): Mechanical test on paint films,
products:
1988 Section 1 Hardness tests (third
(Part l/See 1): Test on liquid paints (general
revision)
1986 and physical), Section 1 Sampling
(third revision) (Part 5/See 2): Mechanical test on paint films,
1988 Section 2 Flexibility and adhesion
(Part l/See 2): Test on liquid paints (general
(third revision)
1987 and physical), Section 2 Preliminary
examination and preparation (Part 5/See 3): Mechanical test on paint films,
of samples for testing (~hird 1986 Section 3 Impact resistance ~ourth
revision) revisiop)

(Part l/See 3): Test on liquid paints (general and (Part 5/See 4): Mechanical test on paint films,
1986 physical), Section 3 Preparation of 1986 Section”4 Print free test (third
panels (third revision) revision)
(Part l/See 4) : Test on liquid paints (general and (Part 6/See 1): Durability tests, Section 1
1987 physical), Section 4 Brushing test 1988 Resistance to humidity under
(third revision) conditions of condensation (third
revision)
(Part l/See 5): Test on liquid paints (general and
1989 physical), Section 5 Consistency (Part 6/See 2): Durability tests, Section 2 Keeping
(third revision) 1989 properties (third revision)
(Part l/See 6): Test on liquid paints (general and (Part 6/See 3): Durability tests, Section 3 Moisture
1987 physical), Section 6 Flash point 1990 vapour permeability (third
(third revision) revision)

PART 5 BUILDING MATERIALS 25


r-

1S No. Title IS No. Title


(Part 6/See 4): Durability tests, Section 4 133:1993 Specification for enamel, interior
1991 Degradation of coatings (pictorial (a) undercoating, (b) finishing
aids for evaluation) (third revision)
(Part 6/See 5): Durability tests, Section 5 137:1965 Specification for ready mixed
1997 Accelerated weathering test (third paint, brushing, matt or egg-shell
revision) flat, finishing, interior, to Indian
(Part 7/See 1) : Environmental tests on paint films, Standard colour, as required
1989 Section 1 Resistance to water (third (revised)
revision) 158:1981 Specification for ready mixed
(Part 7/See 2): Environmental tests on paint films, paint, bmshing, bituminous, black,
1990 Section 2 Resistance to liquids lead-free, acid, alkali, and heat
(third revision) resisting (third revision)
(Part 7/See 3) : Environmental tests on paint films, 168:1993 Specification for ready mixed
1990 Section 3 Resistance to heat (third paint, air-drying semi-glossy/matt,
revision) for general purposes (third
(Part 7/See 4) : Environmental tests on paint films, revision)
1990 Section 4 Resistance to bleeding of 341:1973 Specification for black Japan,
pigments (third revision) Types A, B and C first revision)
(Part 8/See 1): Tests for pigments and other 2074:1992 Specification for ready mixed
1989 solids, Section 1 Residue on sieve paint, air drying red oxide-zinc
(third revision) chrome, priming (second revision)
(Part 8/See 2): Tests for pigments and other 2075:2000 Specification for ready mixed paint,
1990 solids, Section 2 Pigments and non- stoving, red oxide-zinc chrome,
volatile matter (third revision) priming (second revision)
(Part 8/See 3): Tests for pigments and other 2339:1963 Specification for aluminium paint
1993 solids, Section 3 Ash content for general purposes, in dual
(Part 8/See 4): Tests for pigments and other container
1993 solids, Section 4 Phthalic anhydride 2932:2003 Specification for enamel, synthetic,
(Part 8/See 5): Tests for pigments and other exterior, (a) undercoating, (b)
1993 solids, Section 5 Lead restriction finishing (third revision)
test (third revision) 2933:1975 Specification for enamel, exterior,
(Part 8/See 6): Tests for pigments and other (a) undercoating, (b) finishing (jirst
1993 solids, Section 6 Volume solids revision)

(Part 9/See 1): Tests for lacquers and varnish, 3536:1999 Specification for ready mixed
1993 Section 1 Acid value ‘paint, brushing, wood primer (jirst
revision)
(Part 9/See 2): Tests for lacquers and varnish,
1993 Section 2 Rosin test 3537:1966 Specification for ready mixed
paint, finishing, interior for general
104:1979 Specification for ready mixed
purposes, to Indian Standard
paint, brushing, zinc chrome,
colours No. 101, 216, 217, 219,
priming (second revision)
275:”281, 352, 353, 358 to 361,
109:1968 Specification for ready mixed
363,364,388,410,442, 444,628,
paint, brushing, priming, plaster to
631,632,634,693,697, white and
Indian Standard colours No. 361
black
and 631 (jirst revision)
3539:1966 Specification for ready mixed
123:1962 Specification for ready mixed
paint, undercoating, for use under
paint, brushing, finishing, semi-
oil finishes, to Indian Standard
gloss, for general purposes, to
colours, as required
Indian Standard colours No. 445,
446, 448, 449, 451 and 473; and 3585:1966 Specification for ready mixed paint,
red oxide (colour unspecified) aluminium, brushing, priming,
(revised) water resistant, for wood work

26 NATIONAL BUILDING CODE OF JNDIA


IS No. Title IS No. Title

3678:1966 Specification for ready mixed 18. POLYMERS, PLASTICS AND


paint, thick white, for lettering GEOSYNTHETICS/GEOTEXTILES
8662:1993 Specification for enamel, synthetic, 1998:1962 Methods of test for thermosetting
exterior, (a) undercoating, synthetic resin bonded laminated
(b) finishing, for railway coaches sheets
(first revision) 2036:1995 Specification for phenolic
9862:1981 Specification for ready mixed laminated sheets (second revision)
paint, brushing, bituminous black 2046:1995 Specification for decorative
lead free, acid, alkali, water and thermosetting synthetics resin
chlorine resisting bonded laminated sheets (second
11883:1986 Specification for ready mixed revision)
paint, brushing, red oxide, priming 2076:1981 Specification for unsupported
for metals flexible vinyl film and sheeting
13183:1991 Specification for aluminium paints, @rst revision)
heat resistant 2508:1984 Specification for low density
13213:1991 Specification for polyurethane full polyethylene films (second
gloss enamel (two pack) revision)
13607:1992 Specification for ready mixed 6307:1971 Specification for rigid PVC sheets --
paint, finishing, general purposes, 9766:1992 Specification for flexible PVC
synthetic compound (jirst revision)
13871:1993 Specification for powder coatings 10889:1984 Specification for high density
polyethylene films
c) Thinners and Solvents
12830:1989 Specification for rubber based
82:1992 Methods of sampling and test for adhesives for fixing PVC tiles to
thinners and solvents for paints cement
(first revision) 13162 Methods of test for geotextiles:
324:1959 Specification for ordinary (Part 2): 991 Determination of resistance to
denatured spirit (revised) exposure of ultra-violet light and
533:1998 Specification for gum spirit of water (Xenon arc type apparatus)
turpentine (oil of turpentine) (Part 3): 992 Determination of thickness at
(second revision) specified pressure
14314:1995 Specification for thinner general (Part 4): 1992 Determination of puncture
purposes for synthetic paints and resistance by falling cone method
varnishes
(Part 5): 1992 Determination of tensile properties
using a wide width strip
d) Varnishes and Lacquers
13262:1992 Specification for pressure sensitive
337:1975 Specification for varnish, finishing, adhesive tapes with plastic base
interior (tirst revision)
13325:1992 Method of test for the determination
347:1975 Specification for varnish, shellac, to tensile properties of extruded
!
for general purposes @rst revision) polymer geogrids using the wide
348: 968 Specification for French polish strip
(j’irst revision) 13326 (Part 1) : Method of test for the evaluation
524: 983 Specification for varnish, finishing, 1992 of interface friction between
exterior, synthetic (second revision) geosynthetics and soil: Part 1
525: 968 Specification for varnish, finishing, Modified direct shear technique
exterior and general purposes @rst 14182:1994 Specification for solvent cement
revision) for use with unplasticized
642:1963 Specification for varnish medium polyvinylchloride plastic pipe and
for aluminium paint (revised) fittings

PART 5 BUILDING MATERIALS 27


IS No. Title IS No. Title

14293:1995 Method”of test for trapezoid tearing 5219 (Part 1): Specification for cast copper alloy
— Geotextiles 1969 traps: Part 1 ‘P’ and ‘S’ traps
14294:1995 Method of determination of 5455:1969 Specification for cast-iron steps for
apparent opening size by dry manholes
sieving technique — Geotextiles 6411:1985 Specification for gel-coated glass
14324:1995 Method of test for determination of fibre reinforced polyester resin
water permeability -permittivity — bath tubs (jirst revision)
Geotextiles 8718:1978 Specification for vitreous
4443:199’7 Specification for polycarbonate enamelled steel kitchen sinks
sheets 8727:1978 Specification for vitreous
4643:1999 Specification for unsintered enamelled steel wash basins
polytetrafluoroethy lene (PTFE) 9140:1996 Method of sampling of vitreous
tape for thread sealing applications and fire clay sanit~ appliances
4706:1999 Sampling and preparation of test (second revision)
specimen of geotextiles 12701:1996 Specification for rotational moulded
14714:1999 Determination of abrasion polyethylene water storage tanks
resistance of geotextiles (jirst revision)
14715:2000 Specification for woven jute 13983:1994 Specification for stainless steel
geotextiles sinks for domestic purposes
14716: 999 Determination of mass per unit area 14399 Hot press moulded thermosetting
of geotextiles glass fibre reinforced (GRP)
14739: 999 Methods for determination of creep sectional water storage tanks:
of geotextiles (Part 1): 1996 Specification for panels
14753: 999 Specification for poly (methyl) (Part 2): 1996 Guidelines for assembly, installation
methacrylate (PMMA) (Acrylic) and testing
sheets
b) Pipes and Fittings Excluding Valves
14986:2001 Jute gee-grid for rain water erosion
control in road and railway i) Brass and Copper Pipes and Fittings
embankments and hill slopes 407:1981 Specification for brass tubes for
15060:2001 Tensile test for joints/seams by general purposes (third revision)
wide width method of geotextiles 2501:1995 Specification for solid drawn
19. SANITARY APPLIANCES AND WATER copper tubes for general engineering
FITTINGS purposes (third revision)

a) General ii) Cast Iron Pipes and Fittings


775:1970 Specification for cast iron brackets 1536:2001 Specification for centrifugally cast
and supports for wash basins and (spun) iron pressure pipes for
sinks (second revision) water, gas and sewage (fourth
782:1978 Specification for caulking lead revision)
(third revision) 1537:1976 Specification for vertically cast
804:1967 Specification for rectangular iron pressure pipes for water, gas
pressed steel tanks (first revision) and sewage (jlrst revision)
1700:1973 Specification for drinking 1538:1993 Specification for cast iron fittings
fountains (first revision) for pressure pipes for water, gas
2963:1979 Specification for copper alloy and sewage (third revision)
waste fittings for wash-basins and 1729:2002 Specification for sand cast iron
sinks (first revision) spigot and socket soil, waste and
3489:1985 Specification for enamelled steel ventilating pipes, fittings and
bath tubs (@st revision) accessories (second revision)

28 NATIONAL BUILDING CODE OF INDIA


1s No. Title IS No. Title

1879:1987 Specification for malleable cast 12988:1991 Rubber sealing rings for CID
iron pipe fittings (second revision) joints for light duty AC pipes —
3486:1966 Specification for cast iron spigot Dimensional requirements
and socket drainpipes 13382:1992 Cast iron specials for mechanical
3989:1984 Specificationforcentrifugally cast and push on flexible joints for
(spun) iron spigot and socket pressure pipelines for water, gas
soil, waste and ventilating pipes, and sewage
fittings and accessories (second
iii) Lead Pipes and Fittings
revision)
5531:1988 Specification for cast iron specials 404 (Part 1): Specification for lead pipes: Part 1
for asbestos cement pressure pipes 1993 For other than chemical purpose
for water, gas and sewage (second (third revision)
revision)
iv) Fibre Pipes and Fittings
6163:1978 Specification for centrifugally cast
(spun) iron low pressure pipes 11925:1986 Specification for pitch-
for water, gas and sewage (first impregnqted fibre pipes and fittings
revision) for drainage purposes

6418:1971 Specification for cast iron and v) Plastic Pipes and Fittings
malleable cast iron flanges for
general engineering purposes 3076:1985 Specification for low density
polyethylene pipes for potable
7181:1986 Specification for horizontally cast
water supplies (second revision)
iron double flanged pipes for water,
gas and sewage (jlrst revision) 4984:1995 Specification for high density
polyethylene pipes for water
8329:2000 Specification for centrifugally cast
supply (fourth revision)
(spun) ductile iron pressure pipes
for water, gas and sewage (third 4985:2000 Specification for unplasticized
revision) PVC pipes for potable water
supplies (third revision)
8794:1988 Specification for cast iron
detachable joints for use with 7834 Specification for injection moulded
asbestos cement pressure pipes PVC socket fittings with solvent
(first revision) cement joints for water supplies:

9523:1980 Specification for ductile iron (Part 1): 1987 General requirements tjirst revision)
fittings for pressure pipes for water, (Part 2): 1987 Specific requirements for 45°
gas and sewage elbows (lirst revision)
10292:1988 Dimensional requirements for (Part 3): 1987 Specific requirements for 90°
rubber sealing rings for CID joints elbows (jirst revision)
in asbestos cement piping (first (Part 4): 1987 Specific requirements for 90° tees
revision) @rst revision)
10299:1982 Cast iron saddle pieces for service (Part 5): 1987 Specific requirements for 45° tees
connection from asbestos cement (jirst revision)
pressure pipes
(Part 6): 1987 Specific requirements for sockets
11606:1986 Methods of sampling cast iron @rst revision)
pipes and fittings
(Part 7): 1987 Specific requirements for unions
12820:1989 Dimensional requirements of
(jirst revision)
rubber gaskets for mechanical
(Part 8): 1987 Specific requirements for caps
joints and push on joints for use
with cast iron pipes and fittings for (first revision)
carrying water, gas and sewage 8008 Specification for injection moulded
12987:1991 Cast iron detachable joints for use high density polyethylene (HDPE)
with asbestos cement pressure fittings for potable water supplies:
pipes (light duty) (Part 1): 2003 General requirements

PART 5 BUILDINGMATERIALS 29
IS No. Title IS No. Title
(Part 2): 2003 Specific requirements for 90° 12235 Methods of test for unplasticized
bends first revision) PVC pipes for potable water
(Part 3): 2003 Specific requirements for 90° tees supplies:
(Part 1) :1986 Method of measurement of outside
(Part 4): 2003 Specific requirements for reducers
diameter
(Part 5): 2003 Specific requirements for ferrule
(Part 2): 1986 Measurement of wall thickness
reducers (jirst revision)
(Part 3): 1986 Test for opacity
(Part 6): 2003 Specific requirements for pipe ends
(Part 4): 1986 Determining the detrimental effect
(Part 7): 2003 Specific requirements for sandwich
on the composition of water
flanges
(Part 5): 1986 Reversion test
(Pti 8) :2003 Specific requirements for reducing
(Part 6): 1986 Stress relief test
tests
(Part 7): 1986 Test for resistance to sulphuric acid
(Part 9): 2003 Specific requirements for end caps
lj$rst revision) (Part 8): 1986 Internal hydrostatic pressure test
(Part 9): 1986 Impact strength test
8360 Specification for fabricated high
density polyethylene (HDPE) (Part 10) :1986 Method for determination of
fittings for potable water supplies: organotin as tin aqueous solution

(Part 1) :1977 General requirements (Part 11) :1986 Extractability of cadmium and
mercury occurring as impurities
(Part 2): 1977 Specific requirements for 90° tees
12709:1994 Specification for glass-fibre
(Part 3): 1977 Specific requirements for 90°
reinforced plastic (GRP) pipes
bends
joints and fittings for use for
10124 Specification for fabricated PVC potable water supply (fzrst revision)
fittings for potable water supplies: 12818:1992 Specification for unplasticized
(Part 1): 1988 General requirements (first revision) PVC screen and casing pipes for
(Part 2): 1988 Specific requirements for sockets bore/tubewell (jirst revision)
(first revision) 13592:1992 Specification for UPVC pipes for
(Part 3): 1988 Specific requirements of straight soil and waste discharge systems
reducers (jirst revision) inside buildings including
ventilation and rainwater system
(Part 4): 1988 Specific requirements for caps
14333:1996 Specification for high density
(first revision)
polyethylene pipes for sewerage
(Part 5): 1988 Specific requirements for equal
14402:1996 Specification for GRP pipes, joints
tees (jirst revision)
and fittings for use for sewerage,
(Part 6): 1988 Specific requirements for flanged industrial waste and water (other
tail piece with metallic flanges than potable)
@rst revision)
14735:1999 Specification for unplasticized
(Part 7): 1988 Specific requirements for threaded polyvinyl chloride (UPVC)
adaptors (first revision) injection moulded fittings for soil
(Part 8): 1988 Specific requirements for 90° and waste discharge system for
bends (first revision) inside buildings including
ventikition and rain water system
(Part 9): 1988 Specific requirements for 60°
bends @rst revision) 14885:2001 Specification for polyethylene pipe
for supply of gaseous fuel
(Part 10) :1988 Specific requirements for 45°
bends (’jirst revision) 15225:2002 Specification for chlorinated
polyvinyl chloride compounds
(Part 11) :1988 Specific requirements for 30°
used for pipes and fittings
bends (jirst revision)
15328:2003 Specification for unplasticized
(Part 12) :1988 Specific requirements for 22Y2°
non-pressure polyvinyl chloride
bends (first revision)
(PVC-U) pipes for use in
(Part 13) :1988 Specific requirements for 1 1%0 underground drainage and sewerage
bends (jirst revision) ‘system

30 NATIONALBUILDING CODE OF INDIA


IS No. Title IS No. Title
vi) Steel Tubes, Pipes and Fittings (Part 4): 1979 Specific requirements of post
mortom slabs (second revision)
1239 Mild steel tubes, tubular and other
wrought steel fittings: (Part 5): 1979 Specific requirements of shower
trays (second revision)
(Part 1): 1990 Mild steel tubes (fifth revision)
(Part 6): 1979 Specific requirements of bed-pan
(Part 2): 1992 Mild steel tubular and other
sinks (second revision)
wrought steel pipe fittings (third
revision) (Part 7): 1981 Specific requirements of slop sinks
(second revision)
3589:1991 Specification for seamless or
electrically welded steel pipes for 772:1973 Specification for general
water, gas and sewage (168.3 to requirements of enamelled cast
2032 mm outside size) (second iron sanitary appliances (second
revision) revision)

4270:1992 Steel tubes used for water wells 773:1988 Specification for enamelled cast
(second revision) iron water-closets railway stock
type ~ourth revision)
5504:1997 Specification for spiral welded
pipes (first revision) 774:1984 Specification for flushing cisterns
for water-closets and urinals (other
6286:1979 Seamless and welded steel pipe for
than plastic cisterns) (jourth revision)
sub-zero temperature service
1726:1991 Specification for cast iron manhole
6392:1971 Steel pipe flanges
covers and frames (third revision)
vii) Stoneware Pipes and Fittings 2326:1987 Specification for automatic flushing
cisterns for urinals (second
651:1992 Specification for salt-glazed
revision)
stoneware pipes and fittings (Jfth
2548 Specification for plastic seats and
revision)
covers for water-closets:
3006:1979 Specification for chemically
(Part 1): 996 Thermoset seats and covers (jlfth
resistant glazed stoneware pipes
revision)
and fittings (’first revision)
(Part 2): 996 Thermoplastic seats and covers
viii) Asbestos Cement Pipes (fijlh revision)

[See 8 (a) (ii) under the category ‘Composite Matrix 2556 Specification for vitreous sanitary
Products’ ] appliances (vitreous china):
(Part 1): 1994 General requirements (third
ix) Concrete Pipes and Pipes Lined/Coated with revision)
Concrete or Mortar
(Part 2): 1994 Specific requirements of wash-
[See 8 (a) (iv) under the category ‘Composite Matrix down water-closets (fourth
Products’ ] revision)
(Part 3): 1994 Specific requirements of squatting
c) Kitchen and Sanitary Appliances
pans (jourth revision)
771 Specification for glazed fire clay (Part 4): 1994 Specific requirements of wash
sanitary appliances: basins’ (third revision)
(Part 1) :1979 General requirements (second (Part 5): 1994 Specific requirements of laboratory
revision) sinks (third revision)
(Part 2): 1985 Specific requirements of kitchen (Part 6): 1995 Specific requirements of urinals
and laboratory sinks (third revision) and partition plates (Jourth revision)
(Part 3/See 1) : Specific requirements of urinals, (Part 7): 1995 Specific requirements of accessories
1979 Section 1 Slab urinals (second for sanitary appliances (third
revision) revision)
(Part 3/See 2) : Part 3 Specific requirements of (Part 8): 1995 Specific requirements of siphonic
1985 urinals, Section 2 Stall urinals wash-down water closets ~ourth
(third revision) revision)

PART 5 BUILDING MATERIALS 31


IS No. Title 1S No. Title
(Part 9): 1995 Specific requirements of bidets 3950:1979 Specification for surface boxes for
(jlourth revision) sluice valves ($rst revision)
(Part 14) :1995 Specific requirements of integrated 4038:1986 Specification for foot valves for
squatting pans (first revision) water works purposes (second
(Part 15) :1995 revision)
Specific requirements of universal
water closets (first revision) 4346:1982 Specification for washers for use
(Part 16) :2002 with fittings for water services @st
Specific requirements for wash
revision)
down wall mounted water-closets
5312 Specification for swing check type
(Part 17) :1995 Specific requirements for wall
reflux (non-return) valves:
mounted bidets
(Part 1): 1984 Single door pattern (’jirst revision)
5961:1970 Specification for cast iron gratings
for drainage purposes (Part 2): 1986 Multi-door pattern
7231:1984 Specification for plastic flushing 8931:1993 Specification for cast copper alloy
cisterns for water-closets and fancy single tap combination tap
urinals (second revision) and stop valves for water services
(@W revision)
11246:1992 Specification for glass fibre
reinforced polyester resins (GRP) 9338:1984 Specification for cast iron screw-
squatting pans @rst revision) down stop valves and stop and
check valves for water works
d) Valves and Fittings (Including Ferrules) purposes (first revision)
778:1984 Specification for copper alloy gate, 9739:1981 Specification for pressure reducing
globe, and check valves for water valves for domestic water supply
works purposes ~ourth revision) systems
781:1984 Specification for cast copper alloy 9758:1981 Specification for flush valves and
screw-down bib taps and stop fittings for water-closets and urinals
valves for w“ater services (third
9762:1994 Specification for polyethylene
revision)
floats (spherical) for float valves
1701:1960 Specification for mixing valves (/irst revision)
for ablutionary and domestic
9763:2000 Specification for plastic bib taps,
purposes
pillar taps, angle valves, hot and
1703:2000 Specification for copper alloy float cold water services (second revision)
valves (horizontal plunger type)
12234:1988 Specification for plastic
for water supply fittings (third
equilibrium float valve for cold
revision)
water services
1711:1984 Specification for self-closing taps
13049:1991 Specification for diaphragm type
for water supply purposes (second
(plastic body) float operated valves
revision)
for cold water services
1795:1982 Specification for pillar taps for
13114:1991 Specification for forged brass gate,
water supply purposes (second
globe qnd check valves for water
revision)
works purposes
2692:1989 Specification for ferrules for water
14845:2000 Specification for resilient seated
services (second revision)
cast iron air relief valves for water
3004:1979 Specification for plug cocks for works purposes
water supply purposes (first
14846:2000 Specification for sluice valves
revision)
for water works purposes (50 to
3042:1965 Specification for single faced 1200 mm)
sluice gates (200 to 1200 mm size)
e) Water Meters
3311:1979 Specification for waste plug and
its accessories for sinks and 779:1994 Specification for water meters
washbasins (first revision) (domestic type) (sixth revision)

32 NATIONAL BUILDLNG CODE OF LNDL4


IS No. Title IS No. Title
2104:1981 Specification for water meter boxes 8500:1991 Specification for structural steels
(domestic type) (first revision) microalloyed (medium and high
2373:1981 Specification for water meters strength qualities)
(bulk type) (third revision) 8952:1995 Steel ingots, blooms and billets for
6784:1996 Method for performance testing of production of mild steel wire rods
water meters (domestic type) for general engineering purposes
(second revision) (/irst revision)
9467:1980 Steel ingots and billets for
20. SOIL-BASED PRODUCTS production of rivet bars for
1725:1982 Specification for soil-based blocks structural purposes
used in general building c) Sheet and Strip
construction
277:2003 Specification for galvanized steel
21. STEEL AND ITS ALLOYS sheets (plain and corrugated) (sixth
revision)
a) General
412:1975 Specification for expanded metal
1030:1998 Carbon steel castings for general steel sheets for general purposes
engineering purposes (fifth (second revision)
revision)
51“3 :1994 Specification for cold rolled low
1136:1990 Prefen-ed sizes for wrought metal carbon steel sheets and strips
products (j%st revision) ~ourth revision)
137:1990 Thickness of sheet and diameters 1079:1994 Specification for hot rolled carbon
of wire (first revision)
steel sheet and strip (fijlh revision)
762 (Part 1) : Code for designation of steels:
6911:1992 Stainless steel plate, sheet and strip
1974 Part 1 Based on letter symbols (first
(jirst revision)
revision)
7226:1974 Specification for cold rolled
049:1978 Colour code for the identification
medium, high carbon and low alloy
of wrought steel for general
steel strip for general engineering
engineering purposes (first
purposes
revision)
11587:1986 Specification for structural weather
2644:1994 High tensile steel castings (fourth
resistant steels
revision)
14246:1995 Specification for continuously pre-
7598:1990 Classification of steels (jirst revision)
printed galvanized steel sheets and
b) Structural Steel coils

1977:1996 Specification for low tensile 15103:2002 Specification for fire resistant
structural steels (third revision) steel

2062:1999 Specification for steel for general d) Bars, Rods, Wire and Wire Rods
structural purposes (j$fth revision)
280:1978 Specification for mild steel wire for
2830:1992 Specification for carbon steel general engineering purposes
billets ingots, blooms and slabs for (third revision)
re-rolling into steel for general
1148:1982 Specification for hot rolled steel
structural purposes (second
revision) rivet bars (up to 40 mm diameter)
for structural purposes (third
2831:2000 Specification for carbon steel
revision)
billets ingots, blooms and slabs for
re-rolling into low tensile structural 1149:1982 Specification for high tensile steel
steel (third revision) rivet bars for structural purposes
(third revision)
8053:1976 Specification for steel ingots and
billets for the production of steel 1673:1984 Specification for mild steel wire
wire for the manufacture of wood cold heading quality (second
screws revision)

PART 5 BUILDINGMATERIALS 33
IS No. Title IS No. Title
1812:1982 Specification for carbon steel wire 1122:1974 Method of test for determination of
for the manufacture of wood screw true specific gravity of natural
(second revision) building stones (jirst revision)
1835:1976 Specification for round steel wire 1123:1975 Method of identification of natural
for ropes (third revision) building stones (first revision)
2591:1982 Dimensions for hot rolled bars for 1124:1974 Method of test for determination of
threaded components (second water absorption, apparent specific
revision) gravity and porosity of natural
3150:1982 Specification for hexagonal wire building stones (j$rst revision)
netting for general purposes 1125:1974 Method of test for determination of
4826:1979 Specification for hot-dipped weathering of natural building
galvanized coatings on round steel stones (jirst revision)
wires first revision) 1126:1974 Method of test for determination of
6527:1995 Stainless steel wire rod (first durability of natural building
revision) stones (jirst revision)

6528:1995 Specification for stainless steel 1127:1970 Recommendations for dimensions


wire @rst revision) and workmanship of natural
building stones for masonry work
6603:2001 Specification for stainless steel bars
@rst revision)
and flats (jirst revision)
1128:1974 Specification for limestone (slab
7887:1992 Specification for mild steel wire
and tiles) (jirst revision)
rods for general engineering
purposes @rst revision) 1129:1972 Recommendation for dressing
of natural building stones (first
10631:1983 Stainless steel for welding
revision)
electrode core wire
1130:1969 Specification for marble (blocks,
e) Plates slabs and tiles)
3502:1994 Specification for steel chequered 1706:1972 Method of determination of
plates (second revision) resistance to wear by abrasion of
natural building stones (first
f) Tubes and Tubulars
revision)
1161:1998 Specification for steel tubes 3316:1974 Specification for structural granite
for structural purposes (fourth first revision)
revision)
3620:1979 Specification for laterite stone
4516:1968 Specification for elliptical mild block for masonry (jirst revision)
steel tubes
3622:1977 Specification for sand stone (slabs
4923:1997 Specification for hollow mild steel and tiles) (first revision)
sections for structural use (first
4121:1967 Method of test for determination of
revision)
water &ansmission rate by capillary
g) Slotted Sections action through natural building
stones
8081:1976 Specification for slotted sections .
4122:1967 Method of test for surface softening
22. STONES of natural building stones by
exposure to acidic atmospheres
1121 Methods of test for determination
4348:1973 Methods of test for determination
of strength properties of natural
of permeability of natural building
building stones:
stones (jirst revision)
(Part 1): 1974 Compressive strength (Jirst
5218:1969 Method of test for toughness of
revision)
natural building stones
(Part 2): 1974 Transverse strength (first revision)
5640:1970 Method of test for determining the
(Part 3): 1974 Tensile strength @rst revision) aggregate impact value of soft
(Part 4): 1974 Shear strength (jirst revision) coarse aggregates

34 NATIONALBUILDING CODE OF INDLA


p

IS No. Title IS No. Title

6250:1981 Specification for roofing slate tiles 1863:1979 Specification for hot rolled steel
(j%-st revision) bulb flats (jirst revision)
7779 Schedule for properties and 2314:1986 Specification for steel sheet piling
availability of stones for construction sections (jirst revision)
purposes: 3443:1980 Specification for crane rail sections
(Part l/See 1): Gujarat state, Section 1 Availability (first revision)
1975 of stones 3908:1986 Specification for aluminium equal
(Part l/See 2): Gujarat state, Section 2 Engineering leg angles (jirst revision)
1975 properties of building stones 3909:1986 Specification for aluminium
(Part l/See 3): Gujarat state, Section 3 Engineering unequal leg angles (first revision)
1975 properties of stone aggregates 3921:1985 Specification for aluminium
(Part 2/See 1): Maharashtra state, Section 1 channels (jirst revision)
1979 Availability of stones 3954:1991 Specification for hot rolled steel
(Part 2/See 2): Maharashtra state, Section 2 channels sections for general
1979 Engineering properties of building engineering purposes (first
stones revision)
(Part 2/See 3): Maharashtra state, Section 3 3964:1980 Specification for light rails (first
1979 Engineering properties of stone revision)
aggregates 5384:1985 Specification for aluminium
(Part 3/See 2): Tamil Nadu state, Section 2 I-beams (first revision)
1990 Engineering properties of building 6445:1985 Specification for aluminium tee
stones sections (jirst revision)
(Part 3/See 3): Tamil Nadu state, Section 3 12779:1989 Rolling and cutting tolerances for
1980 Engineering properties of stone hot rolled parallel flange beam and
aggregates column sections
(Part 4/See 1 Karnataka state, Sections
b) Dimensional Standards
to 3) :1996 (1 to 3)
808:1989 Dimensions for hot rolled steel
(Part 5/See 1): Andhra Pradesh, Section 1
beam, column channel and angle
1997 Availability of stones
sections (third revision)
(Part 5/See 2): Andhra Pradesh, Section 2
1730:1989 Dimensions for steel plates, sheets
1997 Engineering properties of building
strips and flats for general
stones
engineering purposes (second
(Part 5/See 3) : Andhra Pradesh, Section 3 revision)
1997 Engineering properties of stone
1732:1989 Dimensions for round and square
aggregates
steel bars for structural and general
9394:1979 Specification for stone lintels engineering purposes (second
14223 (Part 1): Specification for polished building revision)
1994 stones: Part 1 Granite 2525:1982 Dimensions for wrought
alumiriium and aluminium alloy
23. STRUCTURAL SECTIONS
wire (jlrst revision)
a) Structural Shapes 2591:1982 Dimensions for hot rolled steel bars
811:1987 Specification for cold formed light for threaded components (second
gauge structural steel sections revision)
(revised) 2673:2002 Dimensions for wrought alurninium
1173:1978 Specification for hot rolled and slit and aluminium alloys, extruded
steel tee bars (second revision) round tube (second revision)

1852:1985 Specification for rolling and 2676:1981 Dimensions for wrought aluminium
cutting tolerances for hot rolled and aluminium alloys, sheet and
steel products (jourth revision) strip (@t revision)

PART 5 BUILDING MATERIALS 35


‘-”-.
IS No. Title IS No. Title
2677:1979 Dimensions for wrought aluminium 9403:1980 Method of test for thermal
and aluminium alloys, plates and conductance and transmittance of
hot rolled sheets (first
revision) built up sections by means of
guarded hot box .i
2678:1987 Dimensions and tolerances for
wrought aluminium and aluminium 9489:1980 Method of test for thermal
alloys, drawn round tubes (second conductivity of materials by means
revision) of heat flow meter
3577:1992 Dimensions and tolerances for 9490:1980 Method of determination for
wrought aluminium and aluminium thermal conductivity of insulation
alloys rivet, bolt and screw stock materials (water calorimeter
(first revision) method)
3965:1981 Dimensions for wrought aluminium 9742:1993 Specification for sprayed mineral
and aluminium alloys, bar, rod and wool thermal insulation (first
section (first revision) revision)
6477:1983 Dimensions for wrought aluminium 9743:1990 Specification for thermal insulation
and aluminium alloys, extruded finishing cements (jirst revision)
hollow sections 9842:1994 Specification for preformed fibrous
12778:1989 Dimensions for hot rolled steel pipe insulation (first revision)
parallel flange beam and column 11128:1994 Specification for spray applied .r-
sections hydrated calcium silicate thermal
insulation
24. THERMAL INSULATION MATERIALS
1 129:1984 Method of test for tumbling
3144:1992 Methods of test for mineral wool friability of preformed block-type
thermal insulation material (second thermal insulation
revision)
1 239 Method of test for rigid cellular
3346:1980 Methods for the determination of thermal insulation materials:
thermal conductivity of thermal
(Part 1): 1985 Dimensions
insulation materials (two slab,
guarded hot-plate method) (first (Part 2): 1985 Apparent density 4

revision) (Part 3): 1985 Dimensional stability


3677:1985 Specification for unbended rock (Part 4): 1985 Water vapour transmission rate
and slag wool for thermal insulation (Part 5): 1985 Volume percent of open and closed
(second revision) cells
4671:1984 Specification for expanded (Part 6): 1985 Heat distortion temperature
polystyrene for thermal insulation
(Part 7): 1985 Coefficient of linear thermal
purposes @rst revision)
expansion at low temperatures
5688:1982 Methods of test for preformed
(Part 8): 1985 Flame height, time of burning and
block-type and pipe-covering type
loss of mass
thermal insulation @rst revision)
(Part 9): 1985 Water absorption
5724:1970 Methods of test for thermal
insulating cement (Part 10) :1985 Flexural strength b

6598:1972 Specification for cellular concrete (Part 11) :1985 Compressive strength
for thermal insulation (Part 12) :1989 Horizontal burning characteristics
7509:1993 Specification for thermal insulating (Part 13) :1992 Determination of flammability by
cement (/irst revision) oxygen index
8154:1993 Specification for preformed calcium 11307:1985 Specification for cellular glass
silicate insulation for temperature block and pipe thermal insulating
up to 650”C) (jirst revision) 11308:1985 Specification for thermal insulating
8183:1993 Specification for bonded mineral castables (hydraulic setting) for
wool (first revision) temperatures up to 1 250”C

36 NATIONALBUILDING CODE OF INDIA


IS No. Title IS No. Title
12436:1988 Specification for preformed (Part 3): 2002 Hexagon nuts (size range Ml.6 to
rigid polyurethane (PUR) and M64) (’jow-th revision)
polyisocyanurate (Pir) foams for (Part 4): 2003 Hexagon thin nuts (chamfered)
thermal insulation (size range M1.6 to M64) ~ourth
13204:1991 Specification for rigid phenolic revision)
foams for thermal insulation (Part 5): 2002 Hexagon thin nuts (unchamfered)
13286:1992 Methods of test for surface spread (size range M1.6 to M1O) (fourth
of flame for thermal insulation revision)
materials (Part 6): 2002 Hexagon nuts, style 2
1365:1978 Specification for slotted countersunk
25. THREADED FASTENERS AND RIVETS
head screws (third revision)
207:1964 Specification for gate and shutter 1366:2002 Specification for slotted cheese
hooks and eyes (revised head screws (third revision)
451:1999 Specification for technical supply 1367 Specification for technical supply
conditions for wood screws (third conditions for threaded steel
revision) fasteners:
554:1999 Specification for pipe threads (Part 1): 2002 Introduction and general information
where pressure-tide joints are made (third revision)
on the threads — Dimensions, Product grades and tolerances
(Part 2): 2002
tolerances and designation (fourth (third revision)
revision)
(Part 3): 2002 Mechanical properties and test
723:1972 Specification for steel countersunk methods for bolts, screws and studs
head wire nails (second revision) with full Ioadability (fourth
724:1964 Specification for mild steel and revision)
brass cup, ruler and square hooks (Part 5): 2002 Mechanical properties and test
and screw eyes (revised) methods for set screws and similar
725:1961 Specification for copper wire nails threaded fasteners not under tensile
(revised) stresses (third revision)

730:1978 Specification for hook bolts for (Part 6): 1994 Mechanical properties and test
corrugated sheet roofing (second methods for nuts with specified
revision) proof loads (third revision)

1120:1975 Specification for coach screws (Part 7): 1980 Mechanical properties and test
(first revision) methods for nuts without specified
proof loads (second revision)
1363 Specification for hexagon head
bolts, screws and nuts of product (Part 8): 2002 Mechanical and performance
properties for prevailing torque
grade C:
type steel hexagon nuts (third
(Part 1): 2002 Hexagon head bolts (size range M 5
revision)
to M64) ($ourth revision)
(Part 9/See 1): Surface diyontinuities, Section 1
(Part 2): 2002 Hexagon head screws (size range 1993 Bolts, screws and studs for general
M5 to M64) ~ourth revision) applications (third revision)
(Part 3): 2002 Part 3 Hexagon nuts (Size range (Part 9/See 2): Surface discontinuities, Section 2
M5 to M64) ~ourth revision) 1993 Bolts, screws and studs for special
1364 Specification for hexagon head applications (third revision)
bolts, screws and nuts of product (Part 10) :2002 Surface discontinuities on nuts
Grades A and B: (third revision)
(Part 1): 2002 Hexagon head bolts (size range (Part 11) :2002 Electroplated coatings (third
Ml.6 to M64) (Jourth revision) revision)
(Part 2): 2002 Hexagon head screws (size range (Part 12) :1981 Phosphate coatings on threaded
Ml.6 to M64) (fourth revision) fasteners (second revision)

PART 5 BIJILDING MATERIALS 37


y-

1S No. Title IS No. Title

(Part 13) :1983 Hot dip galvanized coatings 4206:1987 Dimensions for nominal lengths,
on threaded fasteners (second and thread lengths for bolts, screws
revision) and studs (first revision)
(Part 14/Sec 1): Mechanical properties of corrosion 4762:2002 Specification for worm drive hose
2002 resistance stainless steel fasteners, clips for general purposes (second
Section 1 Bolts, screws and studs revision)
(third revision) 5369:1975 General requirements for plain
(Part 14/Sec 2) : Mechanical properties of corrosion washers and lock washers (first
2002 resistance stainless steel fasteners, revision)
Section 2 Nuts (third revision) 5372:1975 Specification for taper washer for
(Part 14/Sec 3) : Mechanical properties of corrosion channels (ISMC) (first revision)
2002 resistance stainless steel fasteners, 5373:1969 Specification for square washers
Section 3 Set screws and similar for wood fastenings
fasteners not under tensile stress 5374:1975 Specification for taper washers for
(third revision) L-beam (ISMB) (first revision)
(Part 16) :2002 Designation system and symbols 5624:1993 Specification for foundation bolts
(third revision) (first revision)
1929:1982 Specification for hot forged steel 6113:1970 Specification for aluminium ..
rivets for hot closing (12 to 36 mm fasteners for building purposes
diameter) @xt revision) 6610:1972 Specification for heavy washers for
2016:1967 Specification for plain washers steel structures
(jirst revision) 6623:1985 Specification for high strength
2155:1982 Specification for cold forged solid structural nuts (jirst revision)
steel rivets for hot closing (6 to 6639:1972 Specification for hexagon bolts for
16 mm diameter) (jlrst revision) steel structures
2585:1968 Specification for black square bolts 6649:1985 Specification for hardened and
and nuts (dia range 6 to 39 mm) tempered washers for high strength
and black square screws (dia range structural bolts and nuts (first
6 to 24 mm) (first revision) revision)
2643:1999 Dimensions, tolerances and 6733:1972 Specification for wall and roofing
designation for pipe threads where nails
pressure-tight joints are not made 6736:1972 Specification for slotted raised
on the threads (second revision) countersunk head wood screws
2687:1991 Specification for cap nuts (second 6739:1972 Specification for slotted round
revision) head wood screws
2907:1998 Specification for non-ferrous rivets 6760:1972 Specification for slotted
(/irst revision) countersunk head wood screws
2998:1982 Specification for cold forged steel 8033:1976 Specification for washers with
rivets for cold closing (1 to 16 mm square hole for wood fastenings
diameter) (first revision) 8412:1977 Specification for slotted
3063:1994 Specification for fasteners single countersunk head bolts for steel
coil rectangular section spring lock structures
washers (second revision) 8822:1978 Specification for slotted mushroom
3121:1981 Specification for rigging screws head roofing bolts
and stretching screws (first 8869:1978 Specification for washers for
revision) corrugated sheet roofing
3468:1991 Specification for pipe nuts (second 8911:1978 Specification for slotted raised
revision) countersunk head screws
3757:1985 Specification for high strength 10102:1982 Specification for technical supply
structural bolts (second revision) conditions for rivets

38 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title
10238:2001 Specification for step bolts for steel (Part 4) :1993 Pressure head test
structures (Part 5) :1993 Heat resistance test
12427:2001 Specification for transmission (Part 6) :1993 Water absorption test
tower bolts
(Part 7): 1993 Determination of binder content
26. UNIT WEIGHTS OF BUILDING MATERIALS 14695:1999 Specification for glass fibre base
coal tar pitch outer wrap
875 (Part 1): Code of practice for design loads
1987 (other than earthquake) for 28. WELDING ELECTRODES AND WIRES
buildings and structures: Part 1
Dead loads — Unit weights of 814:1991 Specification for covered
building material and stored electrodes for manual metal arc
materials (second revision) welding of carbon and carbon
manganese steel (jljlh revision)
27. WATERPROOFING AND DAMP-PROOFING 1278:1972 Specification for filler rods and
MATERIALS wires for gas welding (second
1322:1993 Specification for bitumen felts for revision)
waterproofing and damp-proofing 1395:1982 Specification for low and medium
~ourth revision) alloy steel covered electrodes for
1580:1991 Specification for bituminous manual metal arc welding (third --
compound for waterproofing and revision)
caulking purposes @-st revision) 2879:1998 Mild steel for metal arc welding
3037:1986 Specification for bitumen mastic electrodes (third revision)
for use in waterproofing of roofs 3613:1974 Acceptance tests for wire flux
(@w revision) combinations for submerged-arc
3384:1986 Specification for bitumen primer welding of structural steel (jirst
for use in waterproofing and damp- revision)
proofing (jrst revision) 4972:1968 Specification for resistance spot-
5871:1987 Specification for bitumen mastic welding electrodes
for tanking and damp-proofing 5206:1983 Covered electrodes for manual arc
(/irst revision) welding of stainless steel and other
7193:1994 Specification for glass fibre base similar high alloy steels (first
coal tar pitch and bitumen felts revision)
(first revision) 5511:1991 Specification for covered
12027:1987 Specification for silicone-based electrodes for manual metal arc
water repellents welding of cast iron (jlrst revision)
13435 Method of tests for acrylic based 5897:1985 Specification for aluminium and
waterproofing material: aluminium alloy welding rods and
(Part 1): 1992 Determination of solid content wires and magnesium alloy
(Part 2): 1992 Determination of coarse particle welding rods (@t revision)

(Part 3): 1992 Determination of capillary water 5898:1970 Specification for copper and
take-up copper “alloy bare solid welding
rods and electrodes
(Part 4): 1992 Determination of pH value
6419:1996 Specification for welding rods and
(Part 5): 1992 Determination of minimum film
bare electrodes for gas shielded arc
forming temperature and white
welding of structural steel (first
point
revision)
13826 Bitumen based felts — Method of
test: 6560:1996 Specification for molybdenum and
chromium-molybdenum low alloy
(Part 1): 1993 Breaking strength test
steel welding rods and bare
(Part 2): 1993 Pliability test electrodes for gas shielded arc
(Part 3): 1993 Storage sticking test welding (jirst revision)

PART 5 BUlLDING MATERIALS 39


FJ-

1S No. Title 1S No. Title


7280:1974 Specification for bare wire 2266:2002 Specification for steel wire ropes
electrodes for submerged-arc for general engineering purposes
welding of structural steels (fourth revision)
8363:1976 Specification for bare wire electrodes 2365:1977 Specification for steel wire
for electroslag welding of steels suspension ropes for lifts, elevators
10631:1983 Stainless steel for welding electrode and hoists (first revision)
core wire
2721:2003 Specification for galvanized steel
29. WIRE ROPES AND WIRE PRODUCTS wire chain link fences fabric
(second revision)
278:1978 Specification for galvanized steel
barbed wire for fencing (third 6594:1977 Specification for technical supply
revision) conditions for wire ropes and
2140:1978 Specification for stranded strands (jlrst revision)
galvanized steel wire for fencing 12776:2002 SpecKlcation for galvanized strand
(@t revision) for earthing (/irst revision)

,,..-

40 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 1 Loads, Forces and Effects

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 DEAD LOAD ... 5
3 IMPOSED LOAD ... 5
4 WIND LOAD ... 14
5 SEISMIC LOAD ... 53
6 SNOW LOAD ... 75
7 SPECIAL LOADS ... 81
8 LOAD COMBINATIONS ... 86
9 MULTI-HAZARD RISK IN VARIOUS DISTRICTS OF INDIA ... 86

ANNEX A ILLUSTRATIVE EXAMPLE SHOWING REDUCTION OF ... 88


UNIFORMLY DISTRIBUTED IMPOSED FLOOR LOADS IN
MULTI-STOREYED BUILDINGS FOR DESIGN OF COLUMNS
ANNEX B NOTATIONS ... 89
ANNEX C BASIC WIND SPEED A 10 m HEIGHT FOR SOME IMPORTANT ... 89
CITIE!VTOWNS
ANNEX D CHANGES IN TERRAIN CATEGORIES ... 90
ANNEX E EFFECT OF A CLIFF OR ESCARPMENT ON THE EQUIVALENT ... 92
HEIGHT ABOVE GROUND (k, FACTOR)
ANNEX F WIND FORCE ON CIRCULAR SECTIONS ... 94
ANNEX G SYMBOLS ... 95
ANNEX H COMPREHENSIVE INTENSITY SCALE (MSK 64) . .. 96
ANNEX J ZONE FACTORS FOR SOME IMPORTANT TOWNS ... 99
ANNEX K SHAPE COEFFICIENTS FOR MULTILEVEL ROOFS . . . 100
ANNEX L VIBRATIONS IN BUILDINGS . . . 101
ANNEX M SUMMARY OF DISTRICTS HAVING SUBSTANTIAL . . . 102
MULTI-HAZARD RISK AREAS

LIST OF STANDARDS . . . 103

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Section covers the various loads, forces and effects which are to be taken into account for structural design
of buildings. The various loads that are covered under this Section are dead load, imposed load, wind load,
seismic load, snow load, special loads and load combinations.

This Code was first published in 1970 and revised in 1983. Subsequently the f~st revision of this Section was
modified in 1987 through Amendment No. 2 to the 1983 version of the Code to bring this Section in line with the
latest revised loading code. Now, in view of the revision of the important Indian Standard on earthquake resistant
design of structure, that is IS 1893, a need to revise this Part was felt. This revision has therefore been prepared
to take into account this revised standard, IS 1893 (Part 1) :2002 ‘Criteria for earthquake resistant design of
structures: Part 1 General provision and buildings (fijih revision)’ and also incorporate latest information on
additional loads, forces and effects as also the details regarding multi-hazard risk in various districts of India.

The significant changes incorporated in this revision include:


.-
a) The seismic zone map is revised with only four zones, instead of five. Erstwhile Zone I has been merged
into Zone II. Hence, Zone I does not appear in the new zoning; only Zones II, III, IV and V do.
b) The values of seismic zone factors have been changed; these now reflect more realistic values of effective
peak ground acceleration considering Maximum Considered Earthquake (MCE) and service life of
structure in each seismic zone.
c) Response spectra are now specified for three types of founding strata, namely rock and hard soil, medium
soil and soft soil.
d) Empirical expression for estimating the fundamental natural period T, of multi-storeyed buildings with
regular moment resisting frames has been revised.
e) This revision adopts the procedure of first calculating the actual force that maybe experienced by the
structure during the probable maximum earthquake, if it were to remain elastic. Then, the concept of
response reduction due to ductile deformation or frictional energy dissipation in the cracks is brought in
this Section explicitly, by introducing the ‘response reduction factor’ in place of the earlier performance
factor.
f) A lower bound is specified for the design base shear of buildings, based on empirical estimate of the
fundamental natural period Ta.
g) The soil-foundation system factor is dropped. Instead, a clause has been introduced to restrict the use of
foundations vulnerable to differential settlements in severe seismic zones.
h) Torsional eccentricity values have been revised upwards in view of serious darpages observed in buildings
with irregular plans.
j) Modal combination rule in dynamic analysis of buildings has been revised.
k) Other clauses have been redrafted where necessary for more effective implementation.
m) A new clause on multi-hazard risk in various districts of India and a list of districts identified as multi-
hazard prone districts have been included.
n) Latest amendments issued to IS 875 have been incorporated.
P) A clause on vibration in buildings has been introduced for general guidance.
q) Reference has been included to the Indian Standards on landslide control and design of retaining walls,
formulated after the last revision of the Section.

The information contained in this Section is largely based on the following Indian Standards:

IS 1893 (Part 1) :2002 Criteria for earthquake resistant design of structures: Part 1 General provisions
and buildings (@h revision)

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 3


IS 875 (Part 2) :1987 Code of practice for design loads (other than earthquake) for buildings and
structures: Part 2 Imposed loads (second revision)
IS 875 (Part 3) :1988 Code of practice for design loads (other than earthquake) for buildings and
structures: Part 3 Wind loads (second revision)
IS 875 (Part 4) :1987 Code of practice for design loads (other than earthquake) for buildings and
structures: Part 4 Snow loads (second revision)
IS 875 (Part 5) :1987 Code of practice for design loads (other than earthquake) for buildings and
structures: Part 5 Special loads and load combinations (second revision)

This Section has to be read together with Sections 2 to 7 of Part 6 ‘Structural Design’.

A reference to SP 64 (S&T) :2001 ‘Explanatory Handbook on Indian Standard Code of practice for design
loads (other than earthquake) for buildings and structures: Part 3 Wind loads IS 875 (Part 3) :1987’ may be
useful. This publication gives detailed background information on the provisions for wind loads and also the use
of these provisions for arriving at the wind loads on buildings and structures while evaluating their structural
safety,

Reference may also be made to the Vulnerability Atlas of India, 1997 and Landslide Hazard Zonation Atlas of
India, 2003 Building Materials and Technology Promotion Council, Ministry of Urban Development and Poverty
Alleviation, Government of India. The vulnerability Atlas contains information pertaining to each State and
Union Territory of India, on (a) seismic hazard map, (b) cyclone, and wind map, (c) flood prone area map, and
(d) housing stock vulnerability table for each district indicating for each house type the level of risk to which it
could be subjected. The Atlas can be used to identify areas in each district of the country which are prone to high
risk from more than one hazard. The information will be useful in establishing the need of developing housing
designs to resist the combination of such hazards.

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 1 Loads, Forces and Effects

1 SCOPE function of these is transaction of public business and


the keeping of books and records.
1.1 This Section covers basic design loads to be
assumed in the design of buildings. The imposed loads, 3.2.1.3 Dwellings — These shall include any building
wind loads, seismic loads, snow loads and other loads, or part occupied by members of single/multi-family
which are specified herein, are minimum working loads units with independent cooking facilities. These shall
which should be taken into consideration for purposes also include apartment houses (flats).
of design.
3.2.1.4 Educational Buildings — These shall include
1.2 This Section does not take into consideration loads any building used for school, college or day-care
incidental to construction. purposes involving assembly for instruction, education
or recreation and which is not covered by assembly
2 DEAD LOAD buildings.
2.1 Assessment of Dead Load 3.2.1.5 Imposed Load — The load assumed to be
The dead load in a building shall comprise the weight produced by the intended use or occupancy of a
of all walls, partitions, floors and roofs, and shall include building including the weight of movable partitions,
the weights of all other permanent constructions in the distributed and concentrated loads, loads due to impact
building and shall conform to good practice [6-1(1)]. and vibration, and dust loads but excluding wind,
seismic, snow and other loads due to temperature
3 IMPOSED LOAD changes, creep, shrinkage, differential settlement, etc.
3.1 This clause covers imposed loads (live loads) to 3.2.1.6 Industrial Buildings — These shall include any
be assumed in the design of buildings. The imposed building or a part of a building or structure, in which
loads specified herein are minimum loads which should products or materials of various kinds and properties
be taken into consideration for the purpose of structural are fabricated, assembled or processed like assembly
safety of buildings. plants, power plants, refineries, gas plants, mills,
NOTE — This Section does not cover detailed provisions for dairies, factories, workshops, etc.
loads incidental to construction and speciat cases of vibration,
3.2.1.7 Institutional Buildings — These shall include
such as moving machinery, heavy acceleration from cranes,
hoists and the like. Such loads shall be dealt with individually any building or a part thereof, which is used for
in each case. purposes, such as, medical or other treatment in case
of persons suffering from physical and mental illness,
3.2 Terminology
disease or infirmity; care of infants, convalescents or
3.2.1 For the purpose of imposed loads specified aged persons and for penal or correctional detention
herein, the following definitions shall apply: in which the liberty of the inmates is restricted.
Institutional buildings ordinarily provide sleeping
3.2.1.1 Assembly Buildings — These shall include any
accommodation for the occupants. It includes hospitals,
building or part of a building where groups of people
sanitona, custodial institutions or penal institutions like
congregate or gather for amusement, recreation, social,
jails, prisons and reformatories.
religious, patriotic, civil, travel and similar purposes;
for example, theatres, motion picture houses, assembly 3.2.1.8 Occupancy or Use Group — The principal
halls, city halls, marriage halls, town halls, auditoria, occupancy for which a bui,~ing or part of a building is
exhibition halls, museums, skating rinks, gymnasiums, used or intended to be “’used; for the purpose of
restaurants (also used as assembly halls), place of classification of a building according to occupancy,
worship, dance halls, club rooms, passenger stations an occupancy shall be deemed to include subsidiary
and terminals of air, surface and other public occupancies which are contingent upon it. The
transportation services, recreation piers and stadia, etc. occupancy classification is given in the following
groups.
3.2.1.2 Business Buildings — These shall include any
building or part of a building, which is used for 3.2.1.9 O@ce Buildings — The buildings primarily to
transaction of business (other than that covered by be used as an office or for office purposes; ‘office
mercantile buildings); for keeping of accounts and purposes’ include the purpose of administration, clerical
records for similar purposes; offices, banks, work, handling money, telephone and telegraph operating,
professional establishments, court houses, and libraries and operating computers, calculating machines, ‘clerical
shall be classified in this group so far as principal work’ includes writing, book-keeping, sorting papers,

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 5


typing, filing, duplicating, punching cards or tapes, the effects of uniformly distributed loads on the floors
drawing of matter for publication and the editorial specified in Table 1.
preparation of matter for publication.
NOTES
3.2.1.10 Mercantile Buildings — These shall include 1 Where, in Table 1, no vahres are given for concentrated load,
any building or a part of a building which is used it maybe assumed that the tabulated distributed load is adequate
for design purposes.
as shops, stores, market for display and sale of
2 The loads specified in Table 1 are equivalent uniformly
merchandise either wholesale or retail. Office, storage distributed loads on the plan area and provide for normal effects
and service and facilities incidental to the sale of of impact and acceleration. They do not take into consideration
merchandise and located in the same building shall be special concentrated loads and other loads.
included under this group. 3 Where the use of an area or floor is not provided in Table 1,
the imposed load due to the use and occupancy of such an area
3.2.1.11 Residential Buildings — These shall includ~ shall be determined from the anatysis of loads resulting from:
any building in which sleeping accommodation is a) weight of the probable assembly of persons;
provided for normal residential purposes with or b) weight of the probable accumulation of equipment and
furnishing;
without cooking or dining or both facilities (except
c) weight of the probable storage materials; and
buildings under institutional buildings). It includes one
d) impact factor, if any.
or multi-family dwellings, apartment houses (flats),
4 While selecting a particular loading, the possible change in
lodging or rooming houses, restaurants, hostels, use or occupancy of the building should be kept in view.
dormitories and residential hotels. Designers should not necessarily select in every case the lower
loading appropriate to the first occupancy. In doing this they
3.2.1.12 Storage Buildings — These shall include any might introduce considerable restrictions in the use of the
building or part of a building used primarily for the building at a later date, and thereby reduce its utitity.
storage or sheltering of goods, wares or merchandise, 5 The loads specified herein, which are based on estimations,
like warehouses, cold storages, freight depots, transity may be considered as the characteristic loads for the purpose of
limit state method of design till such time statistical data are
sheds, store houses, garages, hangers, truck terminals, established based on load surveys to be conducted in the country.
grain elevators, barns and stables. 6 When an existing building is altered by an extension in
height or area, all existing structural parts affected by the
3.3 Imposed Loads on Floors Due to Use and addition shall be strengthened where necessary and all new
Occupancy structural parts shall be designed to meet the requirements for
building hereafter erected.
3.3.1 Imposed Loads 7 The loads specified in the section does not include loads
The imposed loads to be assumed in the design of incidental to construction. Therefore, close supervision during
constructionis essentiat to ensure that overloadingof the building
buildings shall be the greatest loads that probably will due to loads by way of stacking of building materials or use of
be produced by the intended use or occupancy, but shall equipment (for example, cranes and trucks) during construction
not be less than the equivalent minimum loads specified or loads which may be induced by floor to floor propping in
multi-storeyed construction, does not occur. However, if
in Table 1 subject to any reductions permitted in 3.3.2.
construction loads were of short duration, permissible increase
Floors shall be investigated for both the uniformly in stresses in the case of working stress method or permissible
decrease in load factors in hit state method, as applicable to
distributed load (UDL) and the corresponding relevant design codes, may be aflowed for.
concentrated load specified in Table 1, and designed 8 The loads in Table 1 are grouped together as applicable to
for the most adverse effects but they shall not be buildhrgs having separate principal occupancy or use. For a
considered to act simultaneously. The concentrated buildhrg with multiple occupancies, the loads appropriate to
loads specified in Table 1 maybe assumed to act over the occupancy with comparable use shall be chosen from other
occupancies.
an area of 0.3 m x 0.3 m. However, the concentrated
9 Regarding loading on lift machine rooms including storage
loads need not be considered where the floors are space used for repairing lift machines, designers should go by
capable of effective lateral distribution of this load. the recommendations of lift manufacturers for the present.
Regarding loading due to f+se ceiling, the same should be
All other structural elements shall be investigated for considered as imposed loads dn the roof/floor to which it is fixed.

Table 1 Imposed Floor Loads for Different Occupancies


(Clause 3.3.1)

SI Occupancy Classification Untforrrsty Dktributed Coneerwrated bad


No. Load (UDL)
(1) (2) (3) (4)

i) Residential Buifdings KN/m2 m


a) Dwelling houses:
1) All rooms and kitehens 2.0 1.8
2) Toilets and bathrooms 2.0

6 NATIONAL BUILDING CODE OF INDIA


Table 1 — Concluded
(I) (2) (3) (4)
vi) Merchantik Buildings
O Retail shops 4.0 3.6
b) Wholesale shops — to be calculated but not less than 6.0 4.5
c) Office rooms 2.5 2.7
d) Dining rooms, restaurants and cafeterias 3.0’) 2.7
e) Toilets 2.0 —
$ Kitchens and laundries 3.0 4.5
g) Boiler rooms and plant rooms — to be calculated but not 5.0 6.7
less than
h) Corridors, passages, staircases incltrdirtg fire escapes and 4.0 4.5
lobbies
j) Corridors, passages, staircases subject to loads greater than 5.0 4.5
from crowds, such as wheeled vehicles, trolleys and the like
k) Balconies Same as rooms to which they 1.5 metre run concentrated at
give access but with a the outer edge
minimum of 4.0
vii) Industrial Buikfings4)
4 Work areas without machinery/equipment 2.5 4.5
b) Work areas with machinery/eqtripment3)
1) Light duty ~ 5.0 4.5
2) Medium duty To be calculated but not less than 7.0 4.5
3) Heavy duty J 10.0 4.5
c) Boiler rooms and plant rooms — to be calculated but not 5.0 6.7
less than
d) Cafeterias and dinning rooms 3.0’) 2.7
e) Corridors, passages, staircases including fire escapes 4.0 4.5
f) Corridors, passages, krbbies, staircases subject to machine 5.0 4.5
loads and wheeled vehicles — to be calculated but not less
than
g) Kitchens 3.0 4.5
h) Toilets and bathrcmms 2.0 —
viii) Storage Buildingsa)
4 Storage rooms (other than cold storage) and warehouses — 2.4 kN/m2 per metre of 7.0
to be calculated based on the bulk densi~ of materials storage height with a
stored but not less than minimum of 7.5 kN/m2
b) Cold storage — to be calculated but not less than 5.0 kN/m2 per metre of 9.0
storage height with a
minimum of 15 ItN/mz
c) Corridors, passages, staireases including fire escapes — as 4.0 4.5
per the floor serviced but not less than
d) Corridors, passages subject to loads greater than from 5.0 4.5
crowds, such as wheeled vehicles, irolleys and the like
e) Boiler rooms and plant rooms 7.5 4.5
,’
11where unrestricted assembly of persons is anticipated, the value of UDL sh~d be iu@@ V-r4.0 kN/m2
‘1With fixed seats’ implies that the removal of the seating and the use of the space f~ other purposes is improbable. The maximum
likely load in this case is, therefore, closely controlled. ,@
~)The loading in indus~af builtigs (workshops and factories) varies considerably ad sO dlIW ‘k&ttgs under the teI’SIIS ‘W@,

‘medium’ and ‘heavy’ are introduced in order to aflow for more economical dedgrss but the terms have no speeiaf meaning in
themselves other than the imposed load for which the relevant floor is de.sigttad.1$is, however, important particularly in the case
of heavy weight loads, to assess the actual loads to ensure that they are not in exq of 10 kN/mz; h case where they are in excess,
the design shall be based on the actual loadings.
4)For v~ous mechmical hm~ng equipment which ~e uSed to ~ansp~ goo&, ss in w~ttous, WOr~OpS, StOre r@eu’tS, ek, the

actual load coming from the use of such equipment shall be ascertained and design shouId cater to such loads,

3.3.1.1 Load application whichever arrangement produces critical effects on the


structural elements as provided in respective design
The uniformly distributed loads specified in Table 1
codes.
shall be applied as static loads over the entire floor
area under consideration or a portion of the floor area In the design of floors, the concentrated loads are

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 9


considered to be applied in the positions which produce the reduction of imposed loads in a multi-
the maximum stresses and where deflection is the main storeyed building in the design of column
criterion in the positions which produce the maximum members.
deflections. Concentrated load, when used for the
3.3.2.2 For beams in each floor level
calculation of bending and shear, are assumed to act at
a point. When used for the calculation of local effects, Where a single span of beam, girder or truss supports
such as, cmshing or punching, they are assumed to act not less than 50 m2 of floor at one general level, the
over an actual area of application of 0.3 m x 0.3 m. imposed floor load may be reduced in the design of
the beams, girders or tresses by 5 percent for each
3.3.1.2 Loads due to light partitions
50 mz area supported subject to a maximum reduction
In office and other buildings, where actual loads due of 25 percent. However, no reduction shall be made in
to light partitions cannot be assessed at the time of any of the following types of loads:
planning the floors and the supporting structural
members shall be designed to carry, in addition to other a) any superimposed moving load,
loads, uniformly distributed loads per square metre of b) any actual load due to machinery or similar
not less than 33.33 percent of weight per metre run of concentrated loads,
finished partitions, subject to a minimum of 1 kN/m2, c) the additional load in respect of partition
provided total weight of partition walls per m2 of the walls; and
wall area does not exceed 1.5 kN/m2 and the total d) any impact or vibration.
weight per metre length is not greater than 4.0 kN.
NOTE — The above reduction does not apply to beams,
3.3.2 Reduction in Imposed Loads on Floors girdes or trusses supporting roof loads.

3.3.2.1 For members supporting floors 3.3.3 Posting of Floor Capacities


Except as provided for in 3.3.2.1 (a), the following Where a floor or part of a floor of a building has been
reductions in assumed total imposed loads on the floors designed to sustain a uniformly distributed load
may be made in designing columns, load bearing walls, exceeding 3.0 kNlm2 and in assembly, business
piers, their supports and foundations. mercantile, industrial or storage buildings, a permanent
notice in the form shown below indicating the actual
Number of Floors Reduction in Total
uniformly distributed and/or concentrated loadings for
(Including the Roof) Distributed Imposed Load
which the floor has been structurally designed shall be
to be Carried by on All Floors to be Carried
Member Under posted in a conspicuous place in a position adjacent to
by the Member Under
such floor or on such part of a floor.
Consideration Consideration Percent
(1) (2)
1 o DESIGNED IMPOSED FLOOR LOADING
2 10 Distributed . . . . . . . . . . . . . . . . . . . . . . . . . ..kN/m2
3 20
Concentrated . . .. . . . . . . . . . . . . . . . . . . . . . . ...kN
4 30
5 to 10 40
Label Indicating Designed Imposed
Over 10 50
Floor Loading
a) No reduction shall be made for any plant or NOTES
machinery which is specifically allowed for, 1 The lettering of such notice shall be embossed or cast suitably
or for buildings for storage purposes, on a tablet whose least dimension shatl not be less than 0.25 m
warehouses and garages. However, for other and located not less than 1.54n above floor level with lettering
of a minimum size of 25 mm.
buildings, where the floor is designed for an
imposed floor load of 5.0 kN/m2 or more, the 2 If a concentrated load or a bulk load has to occupy a definite
position on the floor, the same could atso be indicated in the
reductions shown in 3.3.2.1 may be taken lable.
provided that the loading assumed is not less
than it would have been if all the floors 3.4 Imposed Loads on Roofs
had been designed for 5.0 kN/m2 with no
3.4.1 Imposed Lads on Various Types of Roofs
reductions.
NOTE — In case if the reduced load in the lower floor On flat roofs, sloping roofs and curved roofs, the
is lesser than the reduced load in the upper floor, then imposed loads due to use and occupancy of the
the reduced load of the upper floor will be adopted. buildings and the geometry of the types of roofs shall
b) An example is given in Annex A illustrating be as given in Table 2.

10 NATIONAL BUILDING CODE OF INDIA


Table 2 Imposed Loads on Variona Types of Roofs
(Clause 3.4.1)

SI Type of Roof Imposed Load Measured on Flgri Aka Minimum Imposed Load
No. Mearmred on Plan
(1) (2) (3) (4)

i) Fla4 sloping or curved roof with


slopes up to and including 10
degrees
a) Access provided 1.5 kNhn2 3.75 kN uniformly distributed over
any span of one metre width of the
roof dab and 9 kN ttniformfy
distributed over the span of any beam
or truss or widf
b) Access not provided except for 0.75 kN/m2 1.9 lrN ursiforrrdydistributed over any
maintenance sw of one metre width of the roof
slab smd 4.5 kN unifomdy distributed
over the span of any beam or truss or
Walt
ii) Sloping roof with slope greater than For roof membrane sheets or purlins – 0.75 kN/m2 Subject to a minimum of 0.4 kN/m2
10” less 0.02 kN/m2 for every degree increase in slope
over 10”
iii) Curved roof with slope of tine (0.75 -0.52 az) kN/m2 Subject to a minimum of 0.4 kN/m2
obtained by joining sp~ging point where
to the crown with the horizontal,
greater than 10° a=hll
h = height of the highest point of the stmcture
measured from its springing; and
1 = chord width of the roof if singly curved and
shorter of the two sides if doubly curved.
Alternatively, where stmcturat analysis can be
carried out for curved roofs of an slopes in a simple
manner applying the laws of statistics, the curved
roofs shatt be divided into minimum 6 w.@
segments and for each segment imposed load shatl
be calculated appropriate to the slope of the chord
of each segment as given in (i) and (ii).

NOTES
1 The loads given above do not include loads due to snow, rain, dust collection, etc. The roof shatl be designed for imposed loads
given above or for snowkitr load, whkhever is greater.
2 For special types of roofs with highly permeable and absorbent material, the contingency of roof material increasing in weight due
to absorption of moisture shall be provided for.

3.4.1.1 Roofs of buildings used for promenade or 3.4.3 Loads Due to Rain
incidental to assembly purposes shall be designed for
the appropriate imposed floor loads given in Table 1 On surfaces whose positioning, shape and drainage
for the occupancy. system are, such as, to make accumulation of rain water
possible, loads due to such accumulation of water and
3.4.2 Concentrated Load on Roof Coverings the imposed loads for the roof as given in Table 2 shrdl
To provide for loads incidental to maintenance, unless be considered separately and the more critical of the
otherwise specified by the Engineer-in-Charge, all roof two shall be adopted in the design.
coverings (other than glass or transparent sheets made
3.4.4 Dust Loads
of fibre glass) shall be capable of carrying an incidental
load of 0.90 kN concentrated on an area of 12.5 cmz so In areas prone to settlement of dust on roofs (example,
placed as to produce maximum stresses in the covering. steel plants, cement plants), provision for dust load
The intensity of the concentrated load maybe reduced equivalent to probable thickness of accumulation of
with the approval of the Engineer-in-Charge, where it dust may be made.
is ensured that the roof coverings would not be traversed
3.4.5 Loads on Members Supporting Roof Coverings
without suitable aids. In any case, the roof coverings
shall be capable of carrying the loads in accordance Every member of the supporting structure which is
with 3.4.1, 3.4.3, 3.4.4 and wind load. directly supporting the roof covering(s) shall be

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 11


designed to carry the more severe of the following Table 3 Horizontal Loads on Parapets,
loads except as provided in 3.4.5.1: Parapet Walls and Balustrades
(Clause 3.5.1)
a) The load transmitted to the members from the
roof covering(s) in accordance with 3.4.1,3.4.3 S1 Usage Area Intensity of
and 3.4.4; and No. Horizontal Load
kN/m Run
b) Anincidental concentrated load of O.90kN (3)
(1) (2)
concentrated over a length of 12.5 cm placed
i) Light access stairs, gangways and like 0.25
at the most favorable positions on the
not more than 600 mm wide
member.
ii) Light access stairs, gangways and like, 0.35
NOTE — Where it is ensured that the roofs would be more than 600 mm wide; stairways,
traversed only with the aid of planks and ladders capable landings, balconies and parapet walls
of distributing the loads on them to two or more (private and part of dwellings)
supporting members, the intensity of concentrated load iii) All other stairways, landings and 0.75
indicated in 3.4.5 (b) may be reduced to 0.5 kN with balconies and all parapets and handrails
the approval of the Engineer-in-Charge. to roofs [except those subject to
overcrowding covered under (iv)]
3.4.5.1 In case of sloping roofs with slope greater than iv). Para~ets and balustrades in date of 2.25
10’), members supporting the roof purlins, such as asse~bly, such as theatres, ~inemas,
trusses, beams, girders, etc, may be designed for two- churches, schools, places of
entertainment, sports and buildings and
thirds of the imposed load on purlin or roofing sheets. buildings likely to be overcrowded

3.5 Imposed Horizontal Loads on Parapets and NOTE — In the case of guard parapets on a floor of multi-
storeyed car park or crash barriers provided in certain buildings
Balustrades
for fire escape, the value of imposed horizontal load (together
3.5.1 Parapets, Parapet Walls and Balustrades with impact load) may be determined.

Parapets. parapet walls and balustrades, together with which induce impact or vibration, as far as possible,
the members which give them structural support, shall calculations shall be made for increase in the imposed
be designed for the minimum loads given in Table 3. load due to impact In the absence of
or vibration.
These are expressed as horizontal forces acting at sufficient data for such calculation, the increase in the
handrail or coping level. These loads shall be imposed loads shall be as follows:
considered to act vertically also but not simultaneously
with the horizontal forces. The values given in Table 3 Structures Impact Allowance,
are minimum values and where values for actual Percent,
loadings are available, they shall be used instead. Min
a) For frames supporting lifts 100
3.5.2 Grandstands and the Like
and hoists
Grandstands, stadia, assembly platforms, reviewing b) For foundations, footings 40
stands and the like shall be designed to resist a and piers supporting lifts and
horizontal force applied to seats of 0.35 kN per linear hoisting apparatus
metre along the line of seats and 0.15 kN per linear
c) For supporting structures and 20
metre perpendicular to the line of the seats. These
foundations for light
loadings need not be applied simultaneously. Platforms
machinery, shaft or motor
without seats shall be designed to resist a minimum units
horizontal force of 0.25 kN/m2 of plan area.
For supporting structures and 50
3.6 Loading Effects Due to Impact and Vibration foundations for reciprocating
machinery or power units
The crane loads to be considered under imposed loads
shall include the vertical loads, eccentricity effects 3.6.2 Concentrated Imposed Loads with Impact and
induced by vertical loads, impact factors, lateral and Vibration
longitudinal braking forces acting across and along the
crane rails respectively. Concentrated imposed loads with impact and vibration
which may be due to installed machinery shall be
3.6.1 Impact Allowance for Lifls, Hoists andillachinery considered and provided for in the design. The impact
factor shall not be less than 20 percent which is the
The imposed loads specified in 3.3.1 shall be assumed
amount allowable for light machinery.
to include adequate allowance for ordinary impact
conditions. However, for structures carrying loads 3.6.2.1 Provision shall also be made for carrying any

12 NATIONAL BUILDING CODE OF INDIA


Y--

a) For Single Bay Frames — Effect of one crane generally blows horizontal to the ground at high wind
in the bay giving the worst effect shall be speeds. Since vertical components of atmospheric
considered for calculation of surge force; and motion are relatively small, the term ‘wind’ denotes
b) For.14ulti-Bay Frames — Effect of two cranes almost exclusively the horizontal wind, vertical winds
working, one each in any of two bays in the are always identified as such. The wind speeds are
cross-section to give the worst effect shall be assessed with the aid of anemometers or anemographs
considered for calculation of surge force. which are installed at meteorological observatories
at heights generally varying from 10 to 30 m above
3.6.4.3 Tractive force ground.
,
a) Where one crane is in operation with no
4.1.2 Very strong wind speeds (greater than 80 kmJh)
provision for future crane, tractive force from
are generally associated with cyclonic storms,
only one crane shall be taken.
thunderstorms, dust storms or vigorous monsoons. A
b) Where more than one crane is in operation or feature of the cyclonic storms over the Indian area is
there is provision for future crane, tractive that they rapidly weaken after crossing the coasts and
force from two cranes giving maximum effect move as depressions/lows inland. The influence of a
shall be considered. severe storm after striking the coast does not, in general,
NOTE — Lateral surge force and longitudinal tractive exceed about 60 km, though sometimes, it may extend
force acting across and along the crane rail respectively even up to 120 km. Very short duration hurricanes of
shall not be assumed to act simultaneously. However,
very high wind speeds called Kal Baisaki or Norwesters
if there is only one crane in the bay, the lateral and
longitudinal forces may act together simultaneously occur fairly frequently during summer months over
with vertical loads. North-Eastern India.

4.1.3 The wind speeds recorded at any locality are


4 WIND LOAD
extremely variable and, in addition to steady wind at
4.1 General any time, there are effects of gusts which may last for
This clause gives wind forces and their effects (static a few seconds. These gusts cause increase in air
and dynamic) that should be taken into account when pressure but their effect on the stability of the building
designing buildings, structures and components may not be so important; often, gusts affect only part
thereof. of the building and the increased local pressures may
be more than balanced by a momentary reduction in
NOTES
the pressure elsewhere. Because of the inertia of the
1 It is believed that ultimately wind load estimation will be
building, short period gusts may not cause any
made by taking into account the random variation of wind
speed with time, but available theoretical methods have not appreciable increase in stress in the main components
matured sufficiently at present for use in the Section. For of the building, although the walls, roof sheeting and
this reason, equivalent static load estimation which implies a individual cladding units (glass panels) and their
steady wind speed, which has proved to be satisfactory for
supporting members, such as purlins, sheeting rails and
normal, short and heavy stnrctures, is given in 4.5 and 4.6.
However, a heginning has been made to take account of the glazing bars may be more seriously affected. Gusts
random nature of the wind speed by requiring that the along- can also be extremely important for the design of
wind or drag load on structures which are prone to wind structures with high slenderness ratios.
induced oscillations, be also determined by the gust factor
method ($ee 4.8) and the more severe of the two estimates be 4.1.4 The liability of a building to high wind pressures
taken for design. depends not only upon the geographical location and
A large majority of structures met within practice do not, proximity of other obstructions to air flow but also upon
however, suffer wind induced oscillations and generally do
not require to be examined for the dynamic effects of wind the characteristics of the structure itself.
including use of gust factor method. Nevertheless, there are
4.1.5 The effect of win{on the structure as a whole is
various types of structures or their components, such as some
tall buildings, etc, which require investigation of wind incQrced determined by the combined action of external and
oscillations. In identifying and analyzing such structures 4.6 internal pressures acting upon it. In all cases, the
shall be followed. calculated wind loads act normal to the surface to which
2 In the case of tall structures with unsymmetrical geometry, they apply.
the designs may have to be checked for torsional effects due
to wind pressure. 4.1.6 Buildings shall also be designed with due
4.1.1 Wind is air in motion relative to the surface of attention to the effects of wind on the comfort of people
the earth. The primary cause of wind is traced to earth’s inside and outside the buildings.
rotation and differences in terrestrial radiation. The 4.1.7 The stability calculations of the building as a
radiation effects are primarily responsible for whole shall be done considering the combined effect,
convection either upwards or downwards. The wind as well as separate effects of imposed loads and wind

14 NATIONAL BUILDING CODE OF INDIA


loads on vertical surfaces, roofs and other parts of the 4.3.1.8 Ground roughness
building above the general roof level.
The nature of the earth’s surface as influenced by small
4.2 Notations scale obstructions such as trees and buildings (as
distinct from topography) is called ground roughness.
The notations to be followed, unless otherwise
specified in relevant clauses under wind loads, are 4.3.1.9 Gust
given in Annex B. A positive or negative departure of wind speed from
its mean value, lasting for not more than say 2 min
4.3 Terminology
over a specified interval of time.
4.3.1 For the purpose of wind loads, the following
4.3.1.10 Peak gust
definitions shall apply.
Peak gust or peak gust speed is the wind speed
4.3.1.1 Angle of attack — Angle between the direction associated with the maximum amplitude.
of wind and a reference axis of the structure.
4.3.1.11 Fetch length
4.3.1.2 Breadth — Breadth means horizontal
dimension of the building measured normal to the Fetch length is the distance measured along the wind
direction of wind. from a boundaty at which a change in the type of terrain
occurs. When the changes in terrain types are
4.3.1.3 Depth — Depth means the horizontal encountered (such as the boundary of a town or city,
dimension of the building measured in the direction forest, etc), the wind profile changes in character but
of the wind. such changes are gradual and start at ground level,
NOTE — Breadth and depth are dimensions measured in spreading or penetrating upwards with increasing fetch
relation to the direction of the wind, whereas length and width length.
are dimensions related to the plan.
4.3.1.12 Gradient height
4.3.1.4 Developed height
Gradient height is the height above the mean ground
Developed height is the height of upward penetration level at which the gradient wind blows as a result of
of the velocity profile in a new terrain. At large, fetch balance among pressure gradient force, coriolis force
lengths, such penetration reaches the gradient height and centrifugal force. For the purpose of this Section.
above which the wind speed may be taken to be the gradient height is taken as the height above the
constant. At lesser-fetch lengths, a velocity profile of mean ground level above which the variation of wind
a smaller height but similar to that of the fully speed with height need not be considered.
developed profile of that terrain category has to be
taken, with the additional provision that the velocity 4.3.1.13 Mean ground level
at the top of this shorter profile equals that of the The mean ground level is the average horizontal plane
unpenetrated earlier velocity profile at that height. of the area enclosed by the boundaries of the structure.
4.3.1.5 E#ective frontal area 4.3.1.14 Pressure coejlicient
The projected area of the structure normal to the Pressure coefficient is the ratio of the difference
direction of the wind. between the pressure acting at a point on a surface and
the static pressure of the incident wind to the design
4.3.1.6 Element suface area
wind pressure, where the static and design wind
The area of surface over which the pressure coefficient pressure are determined at the height of the point
is taken to be constant. considered after taking into account the geographical
location, terrain conditions ‘and shielding effect. The
4.3.1.7 Force coefficient pressure coefficient is also equal to [l–(VJVZ )2], where
A non-dimensional coefficient such that the total wind VPis the actual wind speed at any point on the structure
force on a body is the product of the force coefficient, at a height corresponding to that of V,.
the dynamic pressure of the incident design wind NOTE — Positive sign of the pressure coefficient indicates
speed and the reference area over which the force is pressure acting towards the surface and negative sign indicates
pressure acting away from the surface.
required.
NOTE — When the force is in the direction of the incident 4.3.1.15 Return period
wind, the non-dimensional coefficient will be called as drag
Return period is the number of years, the reciprocal of
coefficient. When the force is perpendicular to the direction
of incident wind the non-dimensional coefficient will be cafled which gives the probability of extreme wind exceeding
as ‘lift coefficient’. a given wind speed in any one year.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 15


4.3.1.16 Shielding effect averaging interval, greater is the magnitude of the gust
speed.
Shielding effect or shielding refers to the condition
where wind has to pass along some structure(s) or 4.4.2 Basic Wind Speed
structural element(s) located on the upstream wind side,
Figure 1 gives basic wind speed map of India, as
before meeting the structure or structural element under
applicable to 10 m height above mean ground level
consideration. A factor called ‘shielding factor’ is used
for 10 m height above mean ground level for different
to account for such effects in estimating the force on
zones of the country. Basic wind speed is based on
the shielded structures.
peak gust velocity averaged over a short time interval
4.3.1.17 Suction of about 3 s and corresponds to mean heights above
ground level in an open terrain (Category 2). Basic
Suctions means pressure less than the atmospheric wind speeds presented in Fig. 1 have been worked out
(static) pressure and is taken to act away from the for a 50 year return period. Basic wind speed for some
surface. importaht cities/towns is also given in Annex C.
4.3.1.18 Solidity ratio 4.4.3 Design Wind Speed (VZ)
Solidity ratio is equal to the effective area (projected The basic wind speed (VJ for any site shall be obtained
area of all the individual elements) of a frame normal from Fig. 1 and shall be modified to include the
to the wind direction divided by the area enclosed by following effects to get V,, design wind speed at any
the boundary of the frame normal to the wind direction. height for the chosen structure.
NOTE — Solidity ratio is to be calculated for individual frames.
a) risk level; .,--
4.3.1.19 Terrain category b) terrain roughness, height and size of structure;
Terrain category means the characteristics of the and
surface irregularities of an area which arise from natural c) local topography.
or constructed features. The categories are numbered
It can be mathematically expressed as follows:
in increasing order of roughness,
VZ = V,k,k,k,
4.3.1.20 Velocity projile
where
The variation of the horizontal component of the
atmospheric wind speed at different heights above the Vz = design of wind speed at any height z in mfs;
mean ground level is termed as velocity profile. Vb = basic wind speed in mls (Fig. 1);
4.3.1.21 Topography k, = probability factor (risk coefficient) (4.4.3.1);
k, = terrain, height and structure size factor
The nature of the earth’s surface as influenced by the (4.4.3.2); and
hill and valley configurations.
k, = topography factor (4.4.3.3)
4.4 Wind Speed and Pressure NOTE — Design wind speed up to 10 m height from mean
ground level shall be considered constant.
4.4.1 Nature of Wind in Atmosphere
4.4.3.1 Risk coefficient (kl )
In general, wind speed in the atmospheric boundary
layer increases with height from zero at ground level Figure 1 gives basic wind speeds for terrain Category 2
to a maximum at a height called the gradient height. as applicable at 10 m above ground level based on
There is usually a slight change in direction (Ekman 50 year mean return period. The suggested life period
effect) but this is ignored in the Section. The variation to be assumed in desigp and the corresponding kl
with height depends primarily on the terrain conditions. factors for different classes of structure for the purpose
However, the wind speed at any height never remains of design is given in Table 4. In the design of all
constant and it has been found convenient to resolve buildings and structures, a regional basic wind speed
its instantaneous magnitude into an average or mean having a mean return period of 50 years shall be used
value and a fluctuating component around this average except as specified in the note of Table 4.
value. The average value depends on the averaging
4.4.3.2 Terrain, height and structure size factor (k2)
time employed in analyzing the meteorological data
and this averaging time varies from a few seconds to a) Terrain — Selection of terrain categories shall
several minutes. The magnitude of the fluctuating be made with due regard to the effect of the
component of the wind speed, which is called as gust, obstruction which constitute the ground surface
depends on the averaging time. In general, smaller the roughness. The terrain category used in the

16 NATIONAL BUILDING CODE OF INDIA


Table 4 Risk Coefficients for Different Classes of Structures in Different Wind Speed Zones
(Clause 4.4.3.1)

Class of Structure Mean Probable klFactorforBasic Wind Speed


Design Life of (m/s) of
StructureinYears
\
33 39 44 47 50 55
(1) (2) (3) (4) (5) (6) (7) (8)

All general buddi~gs and structures 50 1.0 1.0 1.0 1.0 1.0 1.0
Temporary sheds, structures such as those 5’ 0.82 0.76 0.73 0.71 0.70 0.67
used during construction operations (for
example, formwork and falsework),
structures during construction stages and
boundary walls
Buildings and structures presenting a low 25 0.94 0.92 0.91 0.90 0.90 0.89
degree of hazard to life and property in the .
event of failure, such as isolated towers in
wooded areas, farm buildings, other than
residential buildings
Important buildings and structures, such as 100 1.05 1.06 1.07 1.07 1.08 1.08
hospitals, communications buildings/towers
and power plant structures

1
A-B h{-–h(l-P~)}
XN PN [ N 1
kl=
x* =
50,0.63
A+4B

where

N = mean probable design life of structure in years;


PN = risk level in N consecutive years (prob~bility that the design wind speed is exceeded at least once in N successive
years), nominal value = 0.63;
XN,
. PN = extreme wind speed for given values of N and P~; and
x 50, 0.63 = extreme wind speed for N = 50 years and F’~= 0.63
A and B are coefficients having the following values for different basic wind speed zones:

Zone A B
33 nds 83.2 9.2
39 mis 84.2 14.0
44 I-n/s 88.0 18.0
47 Ill/s 88.0 20.5
50 Ill/s 88.8 22.8
55 In/s 90.8 27.3

NOTE — The factor ICIk based on statistical concepts which take account of the degree of reliability required and period of time
in years during which there will be exposure to wind, that is, life of the structure. Whatever wind speed is adopted for design
purposes, there is always a probability (however small) that it may be exceeded in a storm of exceptional violence; the greater
the period of years over which there will be exposure to wind, the greater js the probability. Higher return periods ranging from
100 to 1 000 years (implying lower risk level) in association with greater periods of exposure may have to be selected for
exceptionally important structures, such as nuclear power reactors and satellite communication towers. Equation given above
may be used in such cases to estimate kl factors for different periods of exposure and chosen probability of exceedence (risk
level). The probability level of 0.63 is normally considered sufficient for design of buildings and structures against wind effects
and the values of kl corresponding to this risk level are given in Table 4.

design of a structure may vary depending on Catego~ . 1 — Exposed open terrain with few
the direction of wind under consideration. or no obstructions and in which the average
Wherever sufficient meteorological height of any objects surrounding the structure
information is available about the nature of is less than 1.5 m.
wind direction, the orientation of any building NOTE — This category includes open sea-coasts and
or st~eture may be suitably planned. flat treeless plains.
Terrian, in which a specific structure stands, Categq 2 — Open terrain with well scattered
shall be assessed as being one of the following obstructions having heights generally between
terrain categories: 1.5 and 10 m.

PARI’ 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 19


NOTE — This is the criterion for measurement of multiplying factors (kz) by which the basic
regional basic wind speeds and includes airilelds, open wind speed given in Fig. 1 shall be multiplied
parklands and undeveloped sparsely built-up outskirts to obtain the wind speed at different heights,
of towns and suburbs. Open land adjacent to sea coast
may also be classified as category 2 due to roughness in each terrain category for different sizes of
of large sea waves at high winds. buildings/structures.
Category 3 — Terrain with numerous closely The buildings/strictures are classified into the
spaced obstruction having the size of following three different classes depending
building-structures up to 10 m in height with upon their size:
or without a few isolated tall structures. ClassA — Buildings and/or their components,
NOTES such as cladding, glazing, roofing etc, having
1 Thiscategory includes wellwooded areas andshrubs, maximum dimension (greatest horizontal or
towns and industrial areas fully or partially developed. vertical dimension) less than 20 m.
2 It is likely that the next higher category than this
will not exist in most design situations and that selection Ckzss B — Buildings rind/or their components,
of a more severe category will be deliberate. such as cladding, glazing, roofing etc,
3 Particular attention must begiven tothe performance having maximum dimension (greatest
of the obstructions in areas affected by fully developed horizontal or vertical dimension) between
tropical cyclones. Vegetation, which is likely to be 20 m and 50 m.
blown”down or defoliated, cannot be relied upon to
maintain Category 3 conditions. Where such sitoation Ckms C— Buildings and/or their components,
may exist, either an intermediate category with velocity such as cladding, glazing, roofing etc, having
multipliers midway between the vafrres for Categories maximum dimension (greatest horizontal or
2 and 3 given in Table 5 or Category 2 should be
vertical dimension) greater than 50 m.
selected having due regard to local conditions.
Category 4 — Terrain with numerous large C) Terrain Categories in Relation to the
high closely spaced obstructions. Direction of Wind — The terrain category
used in the design of a building may
NOTE — This category includes large city centres,
generally with obstructions above 25 m and well vary depending on the direction of wind
developed industrial complexes. under consideration. Where sufficient
b) Variation of Wind Speed with Height for meteorological information is available, the
Different Sizes of Structure in Different basic wind speed may be varied for specific
Terrains (kz Factor) — Table 5 gives wind direction.

Table 5 k2 Factors to Obtain Design Wind Speed Variation with Height in DifTerent
Terrains for Different Classes of Building Structures

[Clause 4.4.3.2 (b)]

Height Terrain Terrain Terrain Terrain


(m) Category 1 Class Category 2 Class Category 3 Class category 4 Cklaa
.= A > r A Y c A \
A B c A B c A B c“ A B c-
10 1.05 1.03 0.99 1.00 0.98 0.93 0.91 0.88 0.82 0.80 0.76 0.67
15 1.09 1.07 1.03 1.05 1.02 0.97 0.97 0.94 0.87 0.80 0.76 0.67
20 1.12 1.10 1.06 1.07 1.05 1.00 1.01 0.9s 0,91 0.80 0.76 0.67
30 1.15 1.13 1.09 1.12 1.10 1.04 1.06 1.03 0.96 0.97 0.93 0.83
50 1.20 1.18 1.14 1.17 1.15 1.10 ‘1.12 1.09 1.02 1.10 1.05 0.95
100 1.26 1.24 1.20 1.24 1.22 1.17 1.20 1.17 1:10 1.20 1.15 1.05
150 1.30 1.28 1,24 1.28 1.25 1.21 1,24 1.21 1.15 1.24 1.20 1.10
200 1.32 1.30 1.26 1.30 1.28 1.24 1.27 1.24 1.1s 1.27 1.22 1.13
250 1.34 1.32 1.28 1.32 1.31 1.26 1.29 1.26 1.20 1.28 1.24 1.16
300 1.35 1.34 1.30 1.34 1.32 1.28 1.31 1.28 1.22 1.30 1.26 1.17
350 1.37 1.35 1.31 1.36 1.34 1.29 1.32 1.30 1.24 1.31 1.27 1.19
400 1.38 1.36 1.32 1.37 1.35 1.30 1.34 1.31 1.25 1.32 1.2s 1.20
450 1.39 1.37 1.33 1.38 1.36 1.31 1.35 1.32 1.26 1.33 1.29 1.21
500 1.40 1.38 1.34 1.39 1.37 1.32 1.36 1.33 1.28 1.34 1.30 1.22

NOTES >.
1 See 4.4.3.2 (b) for definitions of Class A, Class B and Class C structures.
2 Intermediate values may he obtained by finear interpolation, if desired. It is permissible to asarrrueconataqt“windspeed between two
heights for simplicity.

20 NATIONALBUILDING CODE OF INDIA


d) Changes in Terrain Categories — The velocity 4.4.4 Design Wind Pressure
profile for a given terrain category does not
The design wind pressure at any height above mean
develop to full height immediately with the
ground level shall be obtained by the following
commencement of that terrain category, but
relationship between wind pressure and wind
develops gradually to height (h,), which
velocity:
increases with the fetch or upwind distance (x)
1) Fetch and Developed Height pZ=0.6V2 z
Relationship — The relation beween the where
developed height (hx) and the fetch (x)
for wind-flow over each of the four p, = design wind pressure in N/mz at height Z,
terrain categories may be taken as given and
in Table 6. V, = design wind velocity in rrt/s at height Z.
2) For buildings of heights greater than the NOTE — The coefficient 0.6 (in S1 units) in the above
developed height (h..) in Table 6, the formuladepends on a number of factors, and mainly on the
velocity profile may be determined in atmosphericpressure and air temperature.The vrduechosen
correspondsto the average appropriate Indian atmospheric
accordance with the following: conditions.
i) The less or least terrain; or
4.4.5 Offshore Wind Velocity
ii) The method described in Annex D.
Cyclonic storms form far way from the sea coast and
Table 6 Fetch and Developed Height
gradually reduce in speed as they approach the sea
Relationship
coast. Cyclonic storms generally extend up to about
[Clause 4.4.3.2 (b)]
60 km inland after striking the coast. Their effect on
DevelopedHeight, h. in m land is already reflected in basic wind speeds specified
Fetch Terrain Terrain Terrain Terrain in Fig. 1. The influence of wind speed off the coast up
(x) km Category 1 Category 2 Category 3 CategoIY 4 to a distance of about 200 km may be taken as
(1) (2) (3) (4) (5) 1.15 times the value on the nearest coast in the absence
0.2 12 20 35 60 of any definite wind data.
0.5 20 30 35 95
4.5 Wind Pressure and Forces on Buildings/
1 25 45 80 130
Structure
2 35 65 110 190
5 60 100 170 300 4.5.1 General
10 80 140 250 450
The wind load on a building shall be calculated for:
20 120 200 350 500
50 180 300 400 500 a) the building as a whole;
b) individual structural elements as roofs and
4.4.3.3 Topography (kJ, factor) walls; and
The basic wind speed V~ given in Fig. 1 takes account c) individual cladding units including glazing
of the general level of the site above sea level. This and their fixings.
does not allow for local topographic features, such as
4.5.2 Pressure Coefficients
hills, valleys, cliffs, escarpments or ridges, which can
significantly affect wind speed in their vicinity. The The pressure coefficients are always given for a
effect of topography is to accelerate wind near the particular surface or part of the surface of a building.
summits of hills or crests of cliffs, escarpments or The wind load acting no+ to a surface is obtained
ridges and decelerate the wind in valleys or near the by multiplying the area of tliat surface or its appropriate
foot of cliffs, steep escarpments or ridges. portion by the pressure coefficient (CP); and the design
wind pressure at the height of the surface from the
The effect of topography will be significant at a site
ground. The average values of these pressure
when the upwind slope is greater than about 3°, and
coefficients for some building shapes are given
below that the value of k~ may be taken to be equal
in 4.5.2.2 and 4.5.2.3.
to 1.0. The value of kq is confined in the range of 1.0
to 1.36 for slopes greater than 3°. A method of Average values of pressure coefficients are given for
evaluating the value of kj for slope greater than 3° is critical wind directions in one or more quadrants. In
given in Annex E. It may be noted that the value of k~ order to determine the maximum wind load on the
varies with height above ground level with a maximum building, the total load should be calculated for each
near the ground, and reducing to 1.0 at higher levels. of the critical directions shown from all quadrants.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 21


Where considerable variation of pressure occurs over rectangular plan shall be as given in Table 7.
a surface, it has been sub-divided and mean pressure In addition, local pressure concentration
coefficients given for each of its several parts. coefficients are also given.
In addition, areas of high local suction (negative b) Pitched Roofs of Rectangular Clad Buildings
pressure concentration) frequently occurring near the — The average external pressure coefficients
edges of walls and roofs are separately shown. and pressure concentration coefficients for
Coefficients for the local effects should only be used pitched roofs of rectangular clad building
for calculation of forces Ori these local areas affecting shall be as given in Table 8. Where no
roof sheeting, glass panels and individual cladding pressure concentration coefficients are given,
units including their fixtures. They should not be used the average coefficients apply. The pressure
for calculating force on entire structural elements such coefficients on the underside of any over-
as roof, walls or structure as a whole. hanging roof shall be taken in accordance with
4.5.2.2 (g).
NOTES
1 The pressure coefficients given in the different tables have NOTES
been obtained mainly from measurements on models in wind 1 The pressure concentration shatl be assumed to act
tunnels, and the great majority of data available have been outward (suction pressure) at the ridges, eaves, cornices
obtained in conditions of relatively smooth flow. Where and 90° comers of roofs.
sufficient field data exist as in the case of rectangular buildings, 2 The pressure concentration shall not be included
values have been obtained to allow for turbulent flow. with the net external pressure when computing overall
2 In recent years, wall glazing and cladding design has been a loads.
source of major concern. Although of less consequence than c) Monoslope Roofs of Rectangular Load
collapse of the main structures, damage to glass can be
Buildings — The average pressure coefficient
hazardous and cause considerable financiat losses,
and pressure concentration coefficient for
3 For pressure coefficients for structures not covered herein,
reference may be made to specialist literature on the subject monoslope (lean-to) roofs of rectangular clad
or advise may be sought from specialists in the subject, buildings shall be as given in Table 9.
d) Canopy Roofswith?4 c h/w <1 and 1< Lfw <3
4.5.2.1 Wind load on individual members
— The pressure coefficients are given in
When calculating the wind load on individual structural Tables 10 and 11 separately for monopitch
elements such as roofs and walls, and individual and double pitch canopy roofs, such as open-
cladding units and their fittings, it is essential to take air parking garages, shelter areas, outdoor
account of the pressure difference between opposite areas, railway platforms, stadiums and
faces of such elements or units. For clad structures, it theatres. The coeftlcients take account of the
is, therefore, necessary to know the internal pressure combined effect of the wind exerted on and
as well as external pressure. Then the wind load, under the roof for all wind directions; the
F (in N) acting in a direction normal to the individual resultant is to be taken normal to the canopy.
structural element or cladding unit is: Where the local coefficients overlap the
greater of the two given values should be
F = (CP, - CPi)Ap~
taken. However, the effect of partial closures
where of one side and or both sides, such as those
due to trains, buses and stored materials shall
c,, = external pressure coefficient;
be foreseen and taken into account.
CPi = internal pressure coefficient; The solidity ratio @ is equal to the area of
A = surface area of structural element or obstruction under the canopy divided by the
cladding unit in mz; and gross area undqr the canopy, both areas
p~ = design wind pressure in N/mz normal to the wihd direction. @= Orepresents
a canopy with no obstructions underneath.
NOTES
# = 1 represents the canopy fully blocked with
1 If the surface design pressure varies with height, the surface
contents to the downwind eaves. Vahtes of
areas of tbe structural element may be sub-divided so that the
specified pressures are taken over appropriate areas. CP for intermediate solidifies maybe linearly
2 Positive wind load indicates the force acting towards the interpolated between these two extremes, and
structural element and negative away from it. apply upwind of the position of maximum
blockage only. Downwind of the position of
4.5.2.2 External pressure coefficients maximum blockage the coefficients for @= O
a) Walls — The average external pressure may be used.
coefficient for the walls of clad buildings of In addition to the pressure forces normal to

22 NATIONAL BUILDING CODE OF INDIA


Table 7 External Pressure Coefficients (Cp,)for Walls of Rectangular Clad Buildings
[Clause 4.5.2.2 (a)]

Building Building Elevation Plan Wind Cw for Surface Local


Height Ratio ?lan Ratio mgle /9 Cp
Degree A B c D

(1) I (2) (3) (4) (5) (6) (7) (8) (9) (10)

/<3
0 +0.7 -0.2 -0.5 -0.5
W-5 -0.8
90 -0.5 -0.5 +0.7 –0.2

~<1
W-5

a
c
~<~<4
2W e 0 +0.7 -0.25 -0.6 -0.6
-1.0
x A
B
90 -0.5 -0.5 +0.7 -0.1

~<1<3
—— /c
W-2

El a
e
A
D
B
0
90
+0.7

-0.6
-0.25

-0.6
-0.6

+0.7
-0.6

-0.25
-1.1

3Z<4
c

II
2W o +0.7 -0.3 -0.7 -0.7
e -1.1
B
\
A 90 -0.5 -0.5 +0.7 -0.1

0 +0.8 -0.25 -0.8 -0.8


/<3 -1.2
w-z 90 4.8 -0.8 +0. 8 -0.25

3h
~<1—<6 c
w

0 +0.7 -0.4 -0.7 -0.7


H<4 –1.2
2W 90 -0.5 -0.5 +0. 8 –0.1
D
.

13
—=—
0 +0.95 -1.85 -0.9 -0.9
–1.25
W2 +0.9 –0.85
90 -0.8 -0.8

h B 0 +0.95 -0.25 -0.7 -0.7


—>6 ~=loo
w w -1.25
90 4.7 -0.7 +0.95 –1.25

1 0 +0.85 -0.75 -0.75 -0.75


–=2 –1.25
w 90 -0.75 -0.75 +0.85 -0.75
—

NOTE — h is the height of eaves or parapet, 1 is the greater horizontal dimension of a building and w is the lesser horizontal
dimension of a building.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 23


Table 9 External Pressure Coefficients (Cw) for Monoslope Roofs for Rectangular
[Clause 4.5.2.2 (c)]

L
Y
ti I

I
WIND I
I
e~
Y = h or 0.15 w, whichever is the lesser

& I
I
I
I
I
I
I
I
.-
Lw----l

Roof Angle
m OVERALL
NOTE — Area H and area L refer to the whole quadrant.

COEFFICIENTS

Wind Angle 8

0° 45° 90° 135° 180°


I

Degree H L H L H&L H&L H L H L


Applies to length w/2 Applies to
from wind wwd end remainder
5 -1.0 -0.5 -1.0 -0.9 -1.0 4.5 -0.9 –1 .0 -0.5 -1.0

J
10 -1.0 -0.5 -1.0 -0.8 -1.0 -0.5 4.8 -1.0 -0.4 –1 .0
15 –0.9 -0.5 -1.0 4.7 –1.0 -0.5 -0.6 -1.0 -0.3 -1.0
20 -0.8 -0.5 -1.0 -0.6 -0.9 -0.5 -0.5 -1.0 -0.2 -1.0
25 -0.7 -0.5 -1.0 -0.6 -0.8 -0.5 -0.3 -0.9 -0.1 4.9
30 -0.5 -0.5 -1.0 -0.6 -0.8 -0.5 -&l’ -0.6 0 -0.6

Roof Angle LOCAL COEFFICIENTS Cw ,A

Degree H, ~ Hz L, b H L

5 -2.0 -1,5 -2.0 -1.5 -2.0 –2.0


10 -2.0 -1.5 -2.0 –1.5 -2.0 -2.0
15 -1.8 -0.9 -1.8 -1.4 -2.0 -2.0
20 -1.8 -0.8 -1.8 -1.4 -2.0 -2.0
25 -1.8 -0.7 -0.9 -0.9 -2.0 -2.0
30 -1.8 -0.5 4.5 -0.5 -2.0 -2.0

NOTE — h is the hekht to eaves at lower side, 1 is greater horizontal dimension of a building and w is the lesser horizontal
dimension of a buildin~.

PART 6 STRUCWRAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 25


f--l “’*. ‘“5’

Table 10 Pressure Coefficients for Free Standing Monosloped Roofs

[Clause 4.5.2.2 (d)]

ROOF ANGLE

+Cp

J
SECTION

-ikudrw”oKEY PLAN

Roof Angle Solidity Ratio Maximum (Largest +ve) and Minimum (Largest -ve)
lressure Coefficients - -

Overall Local coefficients


Degree

0 +0.2 +0.5 +1.8 +1.1


5 +0.4 +0.8 +2.1 +1.3
10 +0.5 +1.2 +2.4 +1.6
15 All values of@ +0.7 +1.4 +2.7 +1.8
20 +0.8 +1.7 +2.9 +2.1
25 +1.0 +2.0 +3.1 +2.3
30 +1.2 +2.2 +3.2 +2.4

o @.() -0.5 -0.6 –1.3 –1.4


@=l -1.0 –1.2 –1.8 –1.9
5 @.() -0.7 -1.1 -1.7 -1.8
@+ –1.1 -1.6 -2.2 –2.3
10 @.() -0.9 -1.5 -2.0 -2.1
Qkl -1.3 -2.1 -2.6 -2.7
15 @.() –1.1 –1.8 -2.4 , -2.5
Qj=l –1.4 -2.3 -2.9 -3.0
20 @=() –1.3 -2.2 -2.8 -2.9
Qkl –1.5 –2.6 -3.1 -3.2
25 0=0 -1.6 -2.6 -3.2 -3.2
Qj=l –1.7 -2.8 -3.5 –3.5
30 0=0 -1.8 -3.0 -3.8 -3.6
0=1 -1.8 -3.0 -3.8 -3.6

NOTE— For monopitch canopies the centre of pressure should be taken to act at 0.3 w from the windward edge.

NATIONAL BUILDING CODE OF INDIA


Table 11 Pressure Coefficients for Free Standing Double Sloped Roofs
[Clause 4.5.2.2 (d)]

ROOF ANGLE

*7
+Cp h

J
-ve ROOF ANGLE

po-ykwo,

KEY PLAN

Roof Angle Solidity Ratio Maximum (Largest +ve) and Minimum (Largest -ve) Pressure Coefficients

Overall Local coefficients


coefficients
Degree I 1 1 j
-20 +0.7 +0.8 +1.6 +0.6 +1.7
-15 +0.5 +0.6 +1.5 +0.7 +1.4
–lo +0.4 +0.6 +1.4 +0.8 +1.1
-5 +0.3 +0.5 +1.5 +0.8 +0.8
+5 +0.3 +0.6 +1.8 +1.3 +0.4
All values of@
+10 +0.4 +0.7 +1.8 +1.4 +0.4
+15 +0.4 +0.9 +1.9 +1.4 +0.4
+20 +0.6 +1.1 +1.9 +1.5 +0.4
+25 +0.7 +1.2 +1.9 +1.6 +0.5
+30 +0.9 +1.3 +1.9 +1.6 +0.7

-20 @.() -0.7 -0.9 -1.3 -1.6 -0.6


gel -0.9 -1.2 -1.7 -1.9 -1.2
-15 @.() -0.6 -0.8 -1.3 -1.6 -0.6
Qj=l -0.8 -1.1 -1.7 –1.9 -1.2
-10 @.() -0.6 -0.8 -1.3 -1.5 -0.6
Qj=l -0.8 -1.1 -1.7 -1.9 -1.3
-5 @.() -0.5 -0.7 -1.3 -1.6 -0.6
@=l -0.8 -1.5 -1.7 -1.9 -1.4
+5 @=() -0.6 -0.6 -1.4 -1.4 -1.1
pj=l -0.9 -1.3 -1.8 -1.8 -2.1
+10 @.() -0.7 -0.7 –1.5 -1.4 -1.4
@=l -1.1 -1.4 -2.0 -1.8 -2.4
+15 @.() -0.8 -0.9 -1.7 -1.4 -1.8
@=l -1.2 -1.5 -2.2 -1.9 -2.8
+20 @.() -0.9 -1.2 –1.8 -1.4 -2.0
Qj=l -1.3 -1.7 -2.3 -1.9 -3.0
+25 @.() -1.0 -1.4 -1.9 –1.4 -2.0
Qkl -1.4 -1.9 -2.4 -2.1 -3.0
+30 @.() -1.0 -1.4 -1.9 -1.4 -2.0
@=l -1.4 -2.1 -2.6 -2.2 -3.0

NOTE — Each slope of a duopitch canopy should be able to withstand forces using both the maximum and the minimum coefficients,
and the whole canopy should be able to support forces using one slope at the maximum coefficient with the other slope at the
minimum coefficient. For duopitch canopies the centre of pressure should be taken to act at the centre of each slope.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 27


Table 13 Pressure Coefficients (Top and Bottom) for Pitched Free Roofs, c%= 30”
with Effects of Train or Stored Materials
[Clause 4.5.2.2 (d)]

r & t
I

l---d~ hr=0.8hJ

c’

(x = 30”
Effects of trains or stored materials:
8 = 0°-45”, or 135°-180°, D, D; E, E’full’length
e = 90°, D, D; E, E’partlength b’

,“
PRESSURE COEFFICIENTS, Cp

D D’ E E’ I Ed Surfacee
I c c’ G G’
0° 0.1 0.8 -0.7 0.9 — — — —

45° -0.1 0.5 -0.8 0.5 — — — —

90° -0.4 -0.5 -0.4 -0.5 -0.3 0.8 0.3 4.4


180° -0.3 0.6 0.4 .-0.6 — — . —

45°Forj: CPtop= –1.5; CPbottom= 0.5.


90”TangentiaUy acting fiction RWO= 0.05 pd.&

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 29


Table 14 Pressure Coefficients (Top and Bottom) for Pitched Free Roofs, a = 10°

[Clause 4.5.2.2 (d)]

I
h= O.5d I
I C’& G’ I
I I
a

L---d---l
ct
————
t
G

D
‘h
e
o0_i-_ —.
●

I
b=5d Rw 0
n.
-1 f= O.2d

G
. ——--

I c

0!= 10°
e = 0° – 45°, D, D; E, E’full length
e= 90°, D, D; E, E’part length b’

PRESSURE COEFFICIENTS, Cp

0 D D’ E I E’ I End Surfaces

c c’ G G’
0° –1.0 0.3 -0.5 0.2

45° -0.3 0.1 -0.3 0.1

90° -0.3 0.0 --0.3 0.0 4.4 0.8 0.3 -0.6

0° Forfi CPtop= –1 .0; CP bottom= 0.40.


()-9()0Tangentially acting friction: RWO= 0.1 ~d.db.

NATIONAL BUILDING CODE OF INDIA


Table 16 Pressure Coetl’icients for Troughed Table 17 Pressure Coefficients for Troughed
Free Roofs, ~ = 10° Free Roofs, oc = 10° with Effects of
Trains or Stored Materials
[Clause 4.5.2.2 (d)]
[Clause 4.5.2.2 (d)]

h’= 0.8h d

1 1
B

b’=d
b’=d
E

1
1

b=5d
7
n Rm

t---
●

f= O.2d b: id

---- I

—d--d Roof slope a = 10°


Effects of trains or stored materials:

Roof slope a = 10“ e = 0°-45°, or 135° – 180°, D, D’, E, E’full length

e = 0°-45°, D, 0; E, E’full length e = 90°, D, D’, E, E‘ part length b“

e = 90°, Q f); E, E’part length b’


1
PRESSURE COEFFICIENTS, Cp

I PRESSURE COEFFICIENTS, Cp
i? D D’ E E’
e D D’ E E’ 00 -0.7 0.8 -0.6 0.6
00
0.3 --0.7 0.2 --0.9 45° -0.4 0.3 -0.2 0.2
45° 0.0 -0.2 0.1 -0.3 90° -0.1 0.1 -0.1 0.1
90° --0.1 0.1 --0.1 0.1 180° -0.4 -1.2 --0.6 --0.3

00 Forfi CPtop= 0.4; CPbottom= 1S. 0° For~ C’Ptop= 1.1; CPbottom= 0.9.
0° – 90° Tangentially acting friction: RWO = 0.1 pd.bd. 0° – 180° Tangentially acting friction: RWO= 0.1 pd.bd.

32 NATIONAL BUILDING CODE OF INDIA


i) Pitched and Saw-Tooth Roofs ofkhdti-span in Tables 19 and 20 respectively, provided
IhknYdings — For pitched and saw-tooth that all spans shall be equal and the height to
roofs of multi-span buildings, the external the eaves shall not exceed the span.
average pressure coefficients and pressure NOTE — Evidence on multi-span buildings is
concentration coefficients shall k as given fragmentary. Any departure given in Tables 19 and 20
should be investigated separately.

Table 19 External Pressure Coefficients (CP,) for Pitched Roofs of Multi-span Buildings
(All Spans Equal) with h > w‘
[Clause 4.5.2.2 (f)]

--i t---l.l w’

r
Y
W 0.1 w’
rhl

Ii

l-- W’ --k--- W’--&--w’ --A----w’--L- W’--w----w’ --’l


ROOF PLAN y=h OR O.lw
WHICHEVER IS
LESSER
a

‘?..
h

SECTION

Roof Angle Wind Angle First First Intermediate Span Other Intermediate End Span Local Coefficient
Span Span
degrees degrees

a 8 u b’ c d m n x z ml m

5 0 -0.9 -0.6 -0.4 -0.3 -0.3 -0.3 -0.3 -0.3


10 -1.1 -0.6 -0.4 -0.3 -0.3 -0.3 -0.3 -0.4
20 -0.7 -0.6 -0.4 -0.3 -0.3 -0.3 -0.3 --0.5 -2.0 –1.5
30 -0.2 -0.6 -0.4 -0.3 -0.2 --0.3 -o.~ --0.5
45 +0.3 -0.6 -0.6 -0.4 -0.2 -0.4 4.2 -0.5

Roof Angle Wind Angle Distance


degrees

a
I degrees

(3 hi
I
hz
1
h3

up to 45 90 -0.8 -0.6 -0.2

Frictional drag: when wind angle 6’ = 0° horizontal forces due to frictional drag are allowed for in the above values;
when wind angle (?= 90° allow for frictional drag in accordance with 4.5.3.1.

NOTE — Evidence on these buildings is fragmentary and any departures from the cases given should be investigated separately.

34 ~ NATIONAL BUILDING CODE OF INDIA


Table 20 External Pressure Coefficients (CP,)for Saw-Tooth Roofs of NIultispan Buildings
(All Spans Equal) with h > w’

[Clause 4.5.2.2 (f)]

---1 p---l.l w’

III /)2

1 w
I

\\\\\\\\\\\~////////w~w////l///~/////Awk\\\\\\\\\y

LwL/vLwL/vd-s-wL+l-

ROOF PLAN y=h OR O,lw


WHICHEVER IS
LESSER
b d n n n z h1=h2=h
a

SECTKMJ

Wind Angle First Span First Intermediate Other Intermediate End Span Local
Span Span Coefficient
degrees

(3 a b c d m n x“ z Isssl Ezzl
I
1
o +0.6 -0.7 --0.7 -0.4 -0.3 -0.2 -0.1 -0.3
-2.0 –1.5
180 -0.5 -0.3 -0.3 -0.3 -0.4 -0.6 -0.6 ~ -0.1

Wind Angle Distance


degrees

9 hl h2 h3

90 -0.8 -0.6 -0.2

270 Similarly, but handed

Frictional drag: when wind angle O = 0° horizontal forces due to frictional drag are allowed for in the above values;
when wind angle O = 90° allow for frictional drag in accordance with 4.5.3.1.

NOTE — Evidence on these buildings is fragmentary and any departures froni the cases given should be
investigated separately.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 35


g) Pressure Coefficients on Overhangs from around a cylindrical structure of circular
Roojk — The pressure coefficients on the top cross-section, the value of external pressure
overhanging portion of the roofs shall be coefficients given in Table 21 may be used
taken to be the same as that of the nearest top provided that the Raynolds number is greater
portion of the non-pressure coefficients for than 10 000. They may be used for wind
the underside surface of the overhanging blowing normal to the axes of cylinders
portions shall be taken as follows and shall having axis normal to the ground plane (that
be taken as positive if the overhanging portion is, chimneys and silos) and cylinders having
is on the windward side: their axis parallel to the ground plane (that is,
1) 1.25, if the overhanging slopes; horizontal tanks) provided that the clearance
downwards; between the tank and the ground is not less
2) 1.0, if the overhanging is horizontal; and than the diameter of the cylinder.

3) 0.75, if the overhanging slopes upwards. his the height of a vertical cylinder or length
of a horizontal cylinder. Where there is a free
For overhanging portions on sides other than
flow of air around both ends, his to be taken
windward side, the average pressure coefficients
as half the length when calculating h/D ratio.
on the adjoining walls maybe used.
1) -0.8, where h/D is not less than 0.3; and
h) Cylindrical Structures =—For the purpose of
calculating the wind pressure distribution 2) –0.5, where h/D is less than 0.3.

Table 21 External Pressure Distribution Coeffkients Around Cylindrical Structures


[Clause 4.5.2.2 (h)]

r
@/d=25

I fh/d=7

‘h/d=l

I
Position of Periphery, d Pressure CoefflcienL . Cmr-

in degrees H/D =25 HZD=7 HLD=l

o 1.0 1.0 1.0


15 0.8 0.8 0.8
30 0.1 0.1 0.1
45 -0.9 -0.8 –0.7
60 -1.9 -1.7 -1.2
75 -2.5 -2.2 -1.6
90 -2.6 -2.2 –1.7
105 -1.9 –1.7 –1.2
120 -0.9 –0.8 -0.7
135 -0.7 -0.6 -0.5
150 -0.6 -0.5 -0.4
165 -0.6 -0.5 -0.5
180 -0.6 -0.5 -0.4

36 NATIONAL BUILDING CODE OF INDIA


j) Roofs and Bottom of Cylindrical Related P = 0.785 D2 (C ~i- Cpe)
pd
Structure —The external pressure coefficients
The resultant of P for roofs lies at 0.1 D from
for roofs and bottoms of cylindrical elevated
the centre of the roof on the windward side.
structures shall be as given in Table 22 (see
also Fig. 2). k) Combined Roofs and Rooj% with a Sky Light
— The average external pressure coefficients
The total resultant load (P) acting on the roof
for combined roofs and roofs with a sky light
of the structure is given by the following
are shown in Table 23.
formula:

o.2D<h<3D
tan a c ().2

SECTION AA

/
0
45

WIND

A
0.2 a

Cpe 9-
- 151
05.
●

0.5 DFOR2<h/D<3 PLAN


0.15h+0.2D FOR0.2<h/D<2

(For force coefficient corresponding to shell portion see Table 23)

FIG. 2 EXTERNALPRESSURECOEFFICIENTS
ON THEUPPERROOF SURFACEOF SINGULAR
CIRCULARSTANDINGON THEGROUND

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 37


Table 22 External Pressure Coefficients for Roofs and Bottoms of
Cylindrical Structures

[Clause 4.5.5.2 (j)]

DIRECTION ~e=o.1 D
Cpe —--e =O.l D
OF WIND -i
I 1
+
+, 1
I

(a) I (d)
I I
I
t Cpe

I
I
D~
d
(b)
I
1
L
[c)
I I

--i--- ,+

Coefficient of External Pressure, Cw

Structure According to Shape

a, b and c I d
H/D Roof (z/H) -1 Roof Bottom
0.5 -0.65 1.00 -0.75 –0.8
1.0 -1.00 1.25 -0.75 -0.7
2.0 -1.00 1.50 -0.75 -0.6

Total force acting on the roof of the structure, P = 0.785 D2 (c~i – Cp)pd.
The resultant of P lies eccentrically, e = 0.1 D.

NATIONAL BUILDING CODE OF INDIA


Table 23—Concluded

b) Roofs with a Sky Light

DIRECTION
+ ().4
OF WIND
-0.6
+

DIRECTION -0,8
OF WIND .—

+ b -0.6
n
a

r’ ~
“ 0.5

I
hl
2

,
?&J

b,> b, b,~~
Portion a b a&b
c. -0.6 +0.7 See Table for
Combined Roofs

m) Grandstands — The pressure coefficients on p) Spheres — The external pressure coefficients


the roof (top and bottom) and rear wall of a for spheres shall be as given in Table 25.
typical grandstand roof, which is open on 4.5.2.3 Internal pressure coefficients
three sides, is given in Table 24. The pressure
coefficients are valid for a particular ratio of Internal air pressure in a building depends upon the
dimensions as specified in Table 24, but may degree of permeability of the cladding to the flow of
be used for deviations up to 20 percent. In air. The internal air pressure may be positive or
general, the maximum wind load occurs, negative depending on the direction of flow of air in
when the wind is blowing into the open front relation to the openings in the buildings.
of the stand causing positive pressure under a) In the case of buildings where the claddings
the roof and negative pressure on the roof. permit the flow of air with openings not more
n) Upper Surface of Round Silos and Tanks — than about 5 percent of the wall areas but
The pressure coefficients on the upper surface where there are no large openings, it is
of round silos and tanks standing on ground necessary to consider the possibility of the
shall be as given in Fig. 2. internal pressure being positive or negative.

40 NATIONALBUILDING CODE OF INDIA


Table 24 Pressure Coefficients at Top and Bottom Roof of Grandstands
Open Three Sides (Roof = 5°)
[Clause 4.5.2.2 (m)]

(h:b:l = 0.8:1: 2.2)

AC I

r
EG

JL KM Front and Back of Wall


1
////////////////////

7I
e J K L M

T
//4
0° , +0.9 -0.5 +0.9 -0.5
45° +0.8 -0.6 +0.4 -0.4
///// 135° -1.1 +0.6 -1.0 +0.4
MR
180° -0.3 +0.9 -0.3 +0.9

oF \ M
w
w I
&f. -CPofK=-l.O
Mw– COof J= +1.0

WIND
J K
e
0“ ----

c G

L M

o D oH

( Shaded area to scale )

Top and Bottom of Roof ,i

~.
0 A B c D E F G
o“ -1.0 +0.9 –1,0 +0.9 -0.7 +0.9 +0.7 +0.9
45° -1.0 +0.7 -0.7 +0.4 -0.5 +0.8 -0.5 +0.3
135° -0.4 -1.1 -0.7 -1.0 -0.9 -1.1 -0.9 -1.0
180° -0.6 -0.3 -0.6 -0.3 -0.6 -0.3 -0,6 -0.3
45° hffR - Cp (top) = ‘2.0
45° MR– Cp (bottom) = +1.0

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 41


--2 \\
%-) ‘

Table 25 ExternalPressure Distribution Coefficients Around Spherical Structures

[Clause 4.5.2.2 (p)]

Position of Periphery, 0 Cp Remarks


in degrees

o +1.0
15 +0.9 Cf = ().5 for DVZ c 7
30 +0.5 = 0.2 for DVZ ~ 7
45 -0.1
60 -0.7 &

75 -1.1
90 -1.2
105 –1.0
120 -0.6
135 -0.2
150 +0.1
165 +0.3
180 +0.4

Two design conditions shall be examined, one through the slits round the closed windows and doors
with an internal pressure coefficient of and through chimneys, ventilators and through the joints
between roof coverings, the total open area being less
+0.2 and another with an internal pressure than 5 percent of the irea of the walls having the
coefficient of –0.2. openings.
The internal pressure coefficient is algebraically b) Building with medium and large openings —
added to the external pressure coefficient and Buildings with medium and large openings
the analysis, which indicates greater distress may also exhibit either positive or negative
of the member, shall be adopted. In most internal pressure depending upon the direction
situations, a simple inspection of the sign of of wind. Buildings with medium openings
the external pressure will at once indicate the between about 5 to 20 percent of wall area
proper sign of the internal pressure coefficient shall be examined for an internal pressure
to be taken for design. coefficient of +0.5 and later with an internal
NOTE — The terms normal permeability relates to the pressure coefficient of –0.5, and the members
flow of air commonly afforded by the claddings not shall be adopted. Buildings with large
only through the open windows and doors, but also openings, that is, openings larger than

42 NATIONAL BUILDING CODE OF INDIA


determine the critical load, the total wind load should be the ground the clearance between the wall or
calculated for each wind direction.
hoarding and the ground shall be not less than
2 If surface design pressure varies with height, the surface area
0.25 times the vertical dimension of the wall
of the building/structure may be sub-divided so that specified
pressure are taken over appropriate areas. or hoarding.
3 In tapered buildings/structures, the force coefficients shall To allow for oblique winds the design shall
be applied after sub-dividing the buildirtg/strnctnre into suitable also be checked for the net pressure normal
number of strips and the load on each strip calculated
to the surface varying linearly from a
individual Iy, taking the area of each strip as A,.
maximum of 1.7 C~ at the up wind edge to
4 Force coefficients for structures not covered herein, reference
may be made to specialist literature on the subject or advise 0.44 C~at the down wind edge.
may be sought from specialists in the subject. The wind load on appurtenances and supports
4.5.3.1 Frictional drag for hoardings shall be accounted for
separately by using the appropriate net
In certain buildings of special shape, a force due to pressure coefficients. Allowance shall be
frictional drag shall be taken into account, in addition made for the shielding effects of one element
to those loads specified in 4.5.2. For rectangular clad or another.
buildings, this addition is necessary only where the
d) Solid circular shapes mounted on a su~ace
ratio d/h or d/b is greater than 4. The frictional drag
— The force coefficients for solid circular
force, F’ in the direction or the wind given by the
shapes mounted on a surface shall be as given .
following formulae:
in Fig. 6.
If h < b, F’= C’~(d- 4h) bp~+ C’~(d - 4h) 2/zp~
4.6 Dynamic Effects . ..
or If h > b, F’= C~(d–4b) bp~+ C}(d–4b) 2hp~
4.6.1 General
The first term in each case gives the dragon the roof
and the second on the walls. The value of C; has the Flexible slender structures and structural elements shall
following values: be investigated to ascertain the importance of wind
induced oscillations for excitations along and across
c; = 0.01 for smooth surfaces without
the direction of wind.
corrugations or ribs across the wind
direction; In general the following guidelines may be used for
c; = 0.02 for surfaces with corrugations or ribs examining the problems of wind induced oscillations:
across the wind direction; a) Buildings and closed structures with a height
c: = 0.04 for surfaces with ribs across the wind to minimum lateral dimension ratio of more
dkection. than about 5.0; or
For other buildings, the frictional drag has been b) Buildings and structures whose natural
indicated, where necessary, in the tables of pressure frequency in the first mode is less than 1.0 Hz.
coefficients and force coefficients. Any building or structure which satisfies
either of the above two criteria shall be
4.5.3.2 Force coefficients for clad buildings
examined for dynamic effects of wind.
a) Clad buildings of uniform section — The NOTES
overall force coefficients for rectangular cIad 1 The fundamental natnral period (~), in seconds, of
buildings of uniform section with flat roofs a moment-resisting frame building without brick irtfil
in uniform flow shall be as given in Fig. 4 panels and of stl other buildings including with brick
infil panels may be estimated in accordance with 5.4.6.
and for other clad buildings of uniform section
2 If preliminary studie~ indicate that wind-induced
(without projections, except where otherwise oscillations are likely to be sigti~cant, investigations
shown) shall be as given in Table 26. should be persued with the aid of snatytical methods
b) Buildings of circular shapes — Force or, if necessary, by means of wind tunnel tests on
models.
coefficients for buildings of circular cross-
3 Cross wind motions may be due to the lateral
section shall be as given in Table 27 (see gustiness of the wind, unsteady wake flow (for example,
Fig. 5 and Annex F). vortex shedding), ne@ive aerodynamic damping or to
c) Low walls and hoardings — Force a combination of these effects. These cross-wind
motions can become critical in the design of tall
coefficients for low walls and hoardings less building structures.
than 15 m high shall be as given in Table 27
4 Motions in the direction of the wind (atso known as
provided the height shall be measured from buffeting) are caused by fluctuating wind force
the ground to the top of the walls or hoarding, associated with gusts. The excitations depend on the
and provided that for walls or hoardings above gust energy available at the resonant frequency.

44 NATIONAL BUILDING CODE OF INDIA


Table 26 Force Coefficients C for Clad Buildings of Uniform Section
(Acting in tie Direction of Wind)

[Clause 4.5.3.2 (a)]

Plan Shape Vzb for H( ht/Breadth Ratio

m2/s up to 1/ 1 2 5“ 10 20 00

All surfaces <6

WIND 0.7 0.7 0.7 0.8 0.9 1.0 1.2


Vz b Rough or with
>6
—
-a projections

(see also Annex E)


Smooth >6
-— 0.5 0.5 0.5 0.5 0.5 0.6 0.6

<10 0.5 0.5 0.5 0.5 0.6 0.6 0.7

b Ellipse b/d= l/2

>10 0.2 0.2 0.2 0.2 0.2 0.2 0.2

<8 0.8 0.8 0.9 1.1 1.3 1.7

-D b Ellipse b/d = 2

28 0.8 0.8 0.9 1.0 1.1 1.3 1.5

“El
<4 0.6 0.6 0.6 0.7 0.8 0.8 1.0
r bid =1
rib= 1/3
24 0.4 0.4 0.4 0.4 0.5 0.5 0.5

“u
<10 0.7 0.8 0.8 0.9 1.0 1.0 1.3
r bld = 1
rib= 1/6
>10 0.5 0.5 0.5 0.5 0.6 0.6 0.6

0.3 0.3 0.3 0.3 0.3 0.3 0.4

0.2 0.2 0.2 0.2 0.3 0.3 0.3

d
4 bld = 1/2 All values 0.5 0.5 0.5 0.5 0.6 0.6 0.7
r b r/b=l16

r--t-+

“m b
bld = 2
rlb = 1/12
All values 0.9 0.9 1.0 1.1 1.2 1.5 1.9

46 NATIONAL BUILDING CODE OF INDIA


Table 26 — Continued

Plan Shape Vzb Ct for Height/Breadth Ratio

m21s LJp
to 1 1 2 5 10 2C

<6 0.7 0.8 0.8 0.9 1.0 1.2 1.6

AU surfaces
b b/d = 2
rlb = 1/4

u’!?!!?!!
>6 0.5 0.5 0.5 0.5 0.5 0.6 0.6

I
<10 0.8 0.8 0.9 1.0 1.1 1.3 1.5

a rla = 1/3

>10 0.5 0.5 0.5 O*5 0.5 0.6 0.6

..

“o
\

rla = 1/12 All values 0.9 -0.9 0.9 1.1 1.2 1.3 1.6
\

A“
~ \‘a rla = 1/48 All values 0.9 0.9 0.9 1.1 1.2 1.3 1.6
45°
@

<11 0.7 0.7 0.7 0.8 0.9 1.0 1.2

0.4 0.4 0.4 0.4 0.5 0.5 0.5

-.

7
“4 1
b rlb = 1/12 All values 0.8 0.8 D.8 1.0 1.1 1.2 1.4

7
4 1
b rlb = 1/48 All values 0.7 0.7 ).8 0.9 1.0 1.1 1.3

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS


Table 26 — Concluded

Pm shape Vzb Ct for Height/Breadth Ratio


mzls Jp to 1/2 1 2 5 10 20 w

<8 0.7 0.7 0.8 0.9 1.0 1.1 1.3

r
---b rlb = U4

U P’ d >8 0.4 0.4 0.4 0.4 0.5 0.5 0.5

1/48 < rlb


All values 1.2 1.2 1.2 1.4 1.6 1.7 2.1
< 1/12

<12 0.7 0.7 0.8 0.9 1.0 1.1 1.3

12 sided
polygon,

0.7 0.7 0.7 0.7 0.8 0.9 1.1

--o Octagon All values 1.0 1.0 1.1 1.2 1.2 1.3 1.4

-0 Hexagon All values 1.0 1.1 1.2 1.4 1.4 1.5

NOTE — Stmctrrres that, because of their size and the design wind velocity, are in the supercritkal flow regime may need fmther
calculation to ensure that the greatest loads do not occur at some wind speed below the maximum when the flow will be sub-
critical.
The coefficients are for buildings without projections, except where othenviae showo. In this table V b is used as an indication of the
airflow regime.

NATIONAL BUILDING CODE OF INDIA


I

1.4
I n 1
Lf I I
FOR 3X104< Re<lo~ — =1.2
I +% ; X103
1.2 I I I

r
.—— —— - 60
- I I I 1 I 40

1.0 1 1 1 i I
I

0.8 IY
1 L --lw-u——J—
Cf
-..
q+% 0“6 - m ~ 0051
~ ~ ~ 0:01
3.0- ‘/
~ 0.002
2.0-
0.4 I
Cf = DRAG COEFFICIENT
I [ I I
. I i II I
0.2 L 1 I 1 I [ I 1 I I I I I I I I

----- EXTRAPOLATED VALUE~

0 I I I I I I I
105 2 345681062 345681072 34568108

Re —p

Cf
FIG. 5 VARIATION OF 1+_2C WITH Re <3 x 104 FOR CIRCULAR SECTIONS
D

Table 27 Force Coefficients for Low Walls or Hoardings (c15 m High)

[Clause 4.5.3.2 (b)]

rbl

I I h’

ABOVE GROUND h’ z 0.25 h ONE EDGE ON GROUND

(Wind normal to face)

Width to Height Ratio, blh Drag Coefficient, Cf

Wall above ground Wall on ground

From 0.5 to 6 From 1 to 12 1.2


10 20 1.3
16 32 1.4
20 40 1.5
40 80 1.7
60 120 1.8
80 or more 160 more 20 2.0

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 49


FIG. 6 FORCECOEFFICIENTS
FOR SOLID SHAPES MUUNTED ON A SURFACE

5 The wake shed from an upstream body may intensify b) Flutter — Flutter is unstable oscillatory motion
motions in the direction of the wind, and may also effect of a structure due to coupling between
crosswind motions. aerodynamic force and the elastic deformation of
the structure. Perhaps the most common form is
6 The designer must be aware of the following three
the oscillatory motion due to combined bending
forms of wind induced motion which are characterized
and torsion. Although oscillatory motions in each
by increasing amplitude of oscillation with increase of
degree of freedom may be dampled, instability
wind speed.
can set in due to energy-. transfer from one mode
a) Galloping — Galloping is transverse oscillations of oscillation to another, and the structure is seen
of some structures due to the development of to execute sustained or divergent oscillations with
aerodynamic forces which are in phase with the a type of motion which is a combination of the
motion. It is characterized by the progressively individual modes of motion. Such energy transfer
increasing amplitude of transverse vibration with takes place when the natural frequencies of the
increase of wind speed. The cross-sections which modes, taken individually, are close to each other
are particularly prone to this type of excitation (ratio being typically less than 2.0). Flutter can
include the following: set in at wind speeds much less than those required
i) All structures with non-circular cross- for exciting the individual modes of motion. Long
sections, such as triangular, square, polygons, span suspension bridge decks or any member of a
as well as angles, crosses and T-sections. structure with large values of dt (where d is the
ii) Twisted cables and cables with ice depth of a structure or structural member parallel
encrustations. to wind stream and tis the least lateral dimension

50 NATIONAL BUILDING CODE OF INDIA


of a member) are prone to low speed flutter. Wind b) Rectangular Structures — For structures of
tunnel testing is required to determine critical
rectangular cross-section:
flutter speeds and the likely structural response.
Other types of flutter are single degree of freedom ~ = 0.15 for all values of b~.
stall flutter, torsional flutter etc.
c) Ovalling— Thin walled strictures with open ends NOTES
at one or both ends, such as oil storage tanks, and 1 Significant cross wind motions maybe produced by
natural draught cooling towers, in which the ratio vortex shedding if the natural frequency of the structure
of the diameter of minimum laterat dimension to or structural element is equal to the frequency of the
the wall thickness is of the order of 100 or vortex shedding within the range of expected wind
more, are prone to ovalling oscillations. These velocities. In such cases, further analysis should be
oscillations are characterized by periodic radial carried out on the basis of references given in Note 8
deformation of the hollow structure. of 4.6.1.
7 Buildings and structures that may be subjected to
2 Unlined welded steel chimney stacks and similar
serious wind excited oscillations require careful
structures are prone to excitation by vortex shedding.
investigation. It is to be noted that wind induced
oscillations may occur at wind speeds lower than the 3 Intensification of the effects of periodic vortex
static design wind speed for the location. shedding has been reported in cases where two or more
similar structures are located in close proximity, for
8 Analytical methods for determining dynamic
example, at less than 20 b apart, where b is the
response of structures to wind loading can be found in
dimension of the structure normrd to the wind.
the following publications:
4 The formulae given in 4.6.2.1 (a) and 4.6.2.1 (b) are
a) Engineering Science Data, Wind Engineering sub-
vatid for irnlnitely long cylindrical structures. The value
series (4 volumes), London, ESDU International.
of S decreases slowly as the ratio of length to maximum
b) ‘Wind Engineering in the Eighties’. Construction transverse width decreases; the reduction being up to -.
Industry Research and Information Association, about half the value, if the structure is only three times
1981, London.
higher than its width. Vortex shedding need not be
c) ‘Wind Effects on Structures’ by E Simiu and considered if the ratio of length to maximum transverse
R.H. Scanlan. Johan Wiley and Sons, New York, width is less than 2.0.
1978.
d) Supplement to the National Building Code of 4.7 Gust Factor (GF) or Gust Effectiveness Factor
Canada, 1980. NRCC, No. 17724. National (GEF) Method
Research Council of Canada, Ottawa, 1980.
e) Wind Forces on Structures by Peter Sachs. 4.7.1 Application
Pergamon Press.
Only the method of calculating load along wind or drag
~ Flow Induced Vibration by Robert D. Clevins.
Von Nostrand Reinfold Co. load by using gust factor method is given in the section
since methods for calculating load across-wind or other
9 In assessing wind loads due to such dynamic
phenomenon as galloping, flutter and ovalling, if the components are not fully matured for all types of
required information is not available either in the structures. However, it is permissible for a designer to
references of Note 8 or other literature, specialist advice use gust factor method to calculate all components of
shall be sought, including experiments on models in
load on a structure using any available theory.
wind tunnels.
However, such a theory must take into account the
4.6.2 Motions Due to Vortex Shedding random nature of atmospheric wind speed.

4.6.2.1 Slender structures — For a structure, the NOTE — It may be noted that investigations for various types
shedding frequency, ~ shall be determined by the of wind induced oscillations out lined in 4.6 are in no way
related to the use of gust facmr method given in 4.7. Although
following formula:
study of 4.6 is needed for using gust factor method.

~=~ 4.7.2 Hourly Mean Wind

Use of the exMng theoties of gust factor method


where
require a knowledge of the maximum of the wind
S = Strouhal number, speeds averaged over one hour at a particular site.
V~ = design wind velocity, and Hourly mean wind speeds at different heights over
b = The breadth of a structure or structural different terrains is given in Table 28.
members in the horizontal plane normal NOTE — It must also be recognized that the ratio of hourly
to the wind direction. mean wind (HMW) to peak gust (PO) given in Table 28 may
not be obtainable in India since extreme wind occurs mainly
a) Circular Structures — For structures circular due to cyclones and thunderstorms, unlike in UK and Canada
in cross-section: where the mechanism is fully developed pressure system.
However Table 28 maybe followed at present for the estimation
S = 0.20 for bVz not greater than 7, and
of the hourly mean wind speed till more reliable values become
S = 0.25 for bVz greater than 7. available.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 51


Table 28 Hourly Mean Wind Speed Factor k2 in - k3 = topography factor (4.4.3.3).
Different Terrains for Different Heights
4.7.3 Along Wind Load
(Clause 4.7.2)
Along wind load on a structure on a strip area (AJ at
Height Terrain
any height (Z) is given by:
m /- -%
Category 1 Category 2 Category 3 Category 4
Fz = C~A~~zG
(1) (2) (3) (4) (5)
where
10 0.78 0.67 0.50 0.24
15 0.82 0.72 0.55 0.24 F z = along wind load on the structure at any
20 0.85 0.75 0.59 0.24
30 0.88 0.79 0.64 0.34
height Z corresponding to strip area A e’
50 0.93 0.85 0.70 0.45 Cf = force coefficient for the building,
100 0.99 0.92 0.79 0.57
150 1.03 0.96 0.84 0.64
A e = effective frontal area considered for the
200 1.06 1.00 0.88 0.68 structure at height Z.
250 1.08 1,02 0.91 0.72
300 1.09 1.04 0.93 0.74
P, = design pressure at height Z due to mean
350 1.11 1.06 0.95 0.77 hourly wind obtained as 0.6 V z (N/m2), and
400 ~,~~ 1.07 0.97 0.79
450 1.13 1.08 0.98 0.81
peak load
G = Rust factor and is given by:
500 1.14 1.09 0.99 0.82 mean load

4.’7.2.1 Variation ofL hourly. mean wind speed with height


G=l+gfr/m]
The variation of hourly mean wind speed with height
shall be calculated as follows:

< = Vbk1&k3 q = peak factor defined as the ratio of the


expected peak value to the root mean value
where
of a fluctuating load, and
v; = hourly mean wind speed in rnls at height z, r= a roughness factor which is dependent on
Vb = regional basic wind speed in mfs (see Fig. 1), the s[ze of the structure in relation to the
k] = probability factor (Table 4), ground roughness.
K. = terrain and height factor (Table 28), and The value of ‘g~r’ is given in Fig. 7.

4.0 4000

3.5 \ 3500

3.0 3000

2.5 2500
\
2.0 2000
L
m- 1●75 “1750 =
IA
1500 :
0
u“ 15
/K/” 0
; 1.25 1250 &J
> z!
>
1.0 1000
/
/ // 900
0.9 /
//
0.8
/ 0 800
‘/
0.7 ‘/ 700
/’
0.6 600
I 1 1 I I t I I 1 1 i 500
0.5
20 50 100 200 500

BUILDING HEIGHT, m

FIG. 7 VALUES OF g~ r AND Lh

52 NATIONAL BUILDING CODE OF INDIA


B is a background factor indicating a measure of 5 SEISMIC LOAD
the slowly varying component of the fluctuating
5.0 This clause deals with assessment of seismic loads
wind load and is obtained from Fig. 8.
on various structures and earthquake resistant design
SE of buildings. (For the purpose of this clause the symbols
— is a measure of the resonant component of the
P given at Annex G are applicable).
fluctuating wind load.
5.1 Terminology for Earthquake Engineering
E is a measure of the available energy in the wind
stream at the natural frequency of the structure 5.1.1 For the purpose of this standard, the following
Lwe Fig. 9). definitions shall apply which are applicable generally
S is size reduction factor (see Fig. 10). to all structures:
~ is the damping coefficient (as a fraction of critical NOTE — For the definitions of terms pertaining to soil
damping) of the structure (see Table 29). mechanics and soil dynamics references may be made to Part 6
‘Structural Design, Section 2 Soils and Foundations’.
@hlZ
— and is to be accounted only for buildings
4 5.1.2 Closely-Spaced Modes
less than 75 m high in terrain category 4 and for
Closely-spaced modes of a structure are those of its
buildings less than 25 high in terrain category 3.
natural modes of vibration whose natural frequencies
and is to be taken as zero in all other cases.
differ from each other by 10 percent or less of the lower
In Fig. 8 and 10, frequency.

C,b C’zfOh 5.1.3 Critical Damping


A —-
—— and f.=
C’zh Vh The damping beyond which the free vibration motion
where will not be oscillatory.

c=y lateral correlation constant which may be taken 5.1.4 Damping


as 10 in the absence of more precise load data;
The effect of internal friction, imperfect elasticity of
c=
z longitudinal correlation constant which may material, slipping, sliding etc, in reducing the amplitude
be taken as 12 in the absence of more precise
of vibration and is expressed as a percentage of critical
load data;
damping.
b= breadth of a structure normal to the wind
stream; 5.1.5 Design Acceleration Spectrum
h = height of a structure; Design acceleration spectrum refers to an average
v= hourly mean wind speed at height 2,
.,z —
smoothened plot of maximum acceleration as a
j o —natural frequency of the structure in the function of frequency or time period of vibration for a
fundamental mode; and specified damping ratio for earthquake excitations at
Lh = a measure of turbulence length scale (see Fig. 7) the base of a single degree of freedom system.

Table 29 Suggested Values of Damping 5.1.6 Design Basis Earthquake (DBE)


Coefficient It is the earthquake which can reasonably be expected
(Clause 4.7.3) to occur at least once during the design life of the
Nature of Structure Damping Coefficient ~
structure.
(1) (2)
5.1.7 Design Horizontal Acceleration Coefficient (AJ
Welded steel structures 0.010
Bolted steel structures 0.020
It is a horizontal acceleration coefficient that shall be
Reinforced concrete structures 0.016 used for design of structures.

5.L8 Design Lateral Force


The peak acceleration along the wind direction at the
top of the structure is given by the following formula: It is the horizontal seismic force prescribed by this
standard, that shall be used to design a structure.

5.1.9 Ductility
where Ductility of a structure, or its members, is the capacity
? = mean deflection at the position where the to undergo large inelastic deformations without
acceleration is required. significant loss of strength or stiffness.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 53

%
k
J .
0.8

0.6

0.4

m 0.3
a“
o
1-
0
$ ‘*2

0.04
b

0.02

.01 .02 .04 .06 .1 .2 .3 .4 .5 .8 1 234 6 810

Czh/L~

FIG. 8 BACKGROUND
FACTOR,B

04
9
03
.
.
02

0.15

.
01

0.05
0.04
0.03

0.02

0.01

2 3 4 6810 20 30 40 6080 100 200 300 600

f~ ~h /~h

FIG. 9 GUSTENERGYFACTOR.E

54 NATIONAL BUILDING CODE OF INDIA


.

.. .

Vh
7 b

4 \ J

08.
05●

04,
C/’)
—. 03
*“.
U24 1
T
1 1 w

g 0.15
1- lx ‘\ .
01
(J fi n’fi
< U.uo
IL
z 0.05
Q 004
~ 0.03
~ 0.02
~ 0.05
fY
~ 0.01
~ 0.008 I

I
I \

0.005 \

0.004
0.003
0.002

C2 fO h
REDUCED FREQUENCY, FO = _
vh

FIG. 10 SIZE REDUCTIONFACTOR. S

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 55

.
5.1.10 Epicentre standard short-period torsion seismometer (with a
period of 0.8 s, magnification 2800 and damping
The geographical point on the surface of earth
nearly critical) would register due to the earthquake at
vertically above the focus of the earthquake.
an epicentral distance of 100 km.
5.1.11 Eflective Peak Ground Acceleration (EPGA)
5.1.19 Maximum Considered Earthquake (MCE)
It is 0.4 times the 5 percent damped average spectral
acceleration between period 0.1 to 0.3 s. This shall be The most severe earthquake effects considered by this
taken as zero period acceleration (ZPA). Code.

5.1.12 Floor Response Spectra 5.1.20 Modal Mass (Mk)

Floor response spectra is the response spectra for a Modal mass of a structure subjected to horizontal or
time history motion of a floor. This floor motion time vertical, as the case may be, ground motion is a part of
history is obtained by an analysis of multi-storey the total seismic mass of the structure that is effective
building for appropriate material damping values in mode k of vibration. The modal mass for a given
subjected to a specified earthquake motion at the base mode has a unique value irrespective of scaling of the
of structure. mode shape.

5.1.13 Focus 5.1.21 Modal Participation Factor (PJ

The originating source of the elastic waves


earthquake Modal participation factor of mode k of vibration is
inside the earth which cause shaking of ground due to the amount by which mode k contributes to the overall
vibration of the structure under horizontal and vertical --
earthquake.
earthquake ground motions. Since the amplitudes of
5.1.14 Importance Factor (Z) 95 per cent mode shapes can be scaled arbitrarily, the
It is a factor used to obtain the design seismic force value of this factor depends on the scaling used for
depending on the functional use of the structure, mode shapes.
characterised by hazardous consequences of its failure, 5.1.22 Modes of Vibration (see 5.1.25)
its post-earthquake functional need, historic value, or
economic importance. 5.1.23 Mode Shape Coe#icient ($iJ

When a system is vibrating in normal mode k, at any


5.1.15 Intensity of Earthquake
particular instant of time, the amplitude of mass i
The intensity of an earthquake at a place is a measure expressed as a ratio of the amplitude of one of the
of the strength of shaking during the earthquake, and masses of the system, is known as mode shape
is indicated by a number according to the modified coefficient (~i~).
Mercalli Scale or M.S.K. scale of Seismic lntenshies
5.1.24 Natural Period (T)
(see Annex H).
Natural period of a structure is its time period of
5.1.16 Liquefaction
undamped free vibration.
Liquefaction is a state in saturated cohesionless soil
5.1.24.1 Fundamental natural period (Tl)
wherein the effective shear strength is reduced to
negligible value for all engineering purpose due to pore It is the fiist (longest) modal time period of vibration.
pressure caused by vibrations during an earthquake
5.1.24.2 Modal natural period (T~ )
when they approach the total confining pressure. In
this condition the soil tends to behave like a fluid mass. The modal natural period of mode k is the time period
of vibration in mode k. ‘
5.1.17 Lithological Features
5.1.25 Normal Mode
The nature of the geological formation of the earth’s
crust above bed rock on the basis of such characteristics A system is said to be vibrating in a normal mode when
as colour, structure, mineralogical composition and all its masses attain maximum values of displacements
grain size. and rotations simultaneously, and pass through
equilibrium positions simultaneously.
5.1.18 Magnitude of Earthquake (Richter’s Magnitude)
5.1.26 Response Reduction Factor (R)
The magnitude of earthquake is a number, which is a
measure of energy released in an earthquake. It is It is the factor by which the actual base shear force,
defined as logarithm to the base 10 of the maximum that would be generated if the structure were to remain
trace amplitude, expressed in microns, which the elastic during its response to the design basis

56 NATIONAL BUILDING CODE OF INDIA


earthquake (DBE) shaking, shall be reduced to obtain of buildings in this standard, the following definitions
the design lateral force. shall apply:

5.1.2’7 Response Spectrum 5.2.2 Base

The representation of the maximum response of It is the level at which inertia forces generated in the
idealized single degree freedom systems having certain structure are transferred to the foundation, which then
period and damping, during earthquake ground motion. transfers these forces to the ground.
The maximum response is plotted against the
5.2.3 Base Dimensions (d)
undamped natural period and for various damping
values, and can be expressed in terms of maximum Base dimension of the building along a direction is
absolute acceleration, maximum relative velocity, or the dimension at its base, in metres, along that
maximum relative displacement. direction.

5.1.28 Seismic Mass 5.2.4 Centre of I14ass

It is the seismic weight divided by acceleration due to The point through which the resultant of the masses of
gravity. a system acts. This point corresponds to the centre of
gravity of masses of system.
5.1.29 Seismic Weight (W)
5.2.5 Centre of Sti&zess
It is the total dead load plus appropriate amounts of
specified imposed load. The point through which the resultant of the restoring
forces of a system acts.
5.1.30 Structural Response Factors (S/g)
5.2.6 Design EccentriciQ (e&)
It is a factor denoting the acceleration response
spectrum of the structure subjected to earthquake It is the value of eccentricity to be used at floor i in
ground vibrations, and depends on natural period of torsion calculations for design.
vibration and damping of the structure.
5.2.7 Design Seismic Base Shear ( V~)
5.1.31 Tectonic Features
It is the total design lateral force at the base of a
The nature of geological formation of the bed rock in structure.
the earth’s crust revealing regions characterized by
5.2.8 Diaphragm
structural features, such as dislocation, distortion,
faults, folding, thrusts, volcanoes with their age of It is a horizontal, or nearly horizontal system, which
formation, which are directly involved in the earth transmits lateral forces to the vertical resisting
movement or quake resulting in the above elements, for example, reinforced concrete floors and
consequences. horizontal bracing systems.

5.1.32 Time History Analysis 5.2.9 Dual System


It is an analysis of the dynamic response of the structure Buildings with dual system consist of shear walls (or
attach increment of time, when its base is subjected to braced frames) and moment resisting frames such
a specific ground motion time history. that:
5.L33 Zone Factor (Z) a) the two systems are designed to resist the total
It is a factor to obtain the design spectrum depending design lateral force in proportion to their
on the perceived maximum seismic risk characterized lateral stiffness considering the interaction of
by maximum considered earthquake (MCE) in the zone the dual system at all floor levels; and
in which the structure is located. The basic zone factors b) the moment resisting frames are designed to
included in this standard are reasonable estimate of independently resist at least 25 percent of the
effective peak ground acceleration. design base shear.

5.1.34 Zero Period Acceleration (ZPA) 5.2.10 Height of Floor (hi)

It is the value of acceleration response spectrum for It is the difference in levels between the base of the
period below 0.03 s (frequencies above 33 Hz). building and that of floor i.

5.2 Terminology for Earthquake Engineering of 5.2.11 Height of Structure (h)


Buildings
It is the difference in levels, in metres, between its base
5.2.1 For the purpose of earthquake resistant design and its highest level.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS. FORCES AND EFFECTS 57


,!

5.2.12 Horizontal Bracing System 5.2.21 Static Eccentrici~ ( e,i )

It is a horizontal truss system that serves the same It is the distance between centre of mass and centre of
function as a diaphragm. rigidity of floor i.

5.2.13 Joint 5.2.22 Storey

It is the portion of the column that is common to other It is the space between two adjacent floors.
members, for example, beams, framing into it.
5.2.23 Storey Drift
5.2.14 Lateral Force Resisting Element
It is the displacement of one level relative to the other
It is part of the structural system assigned to resist level above or below.
lateral forces.
5.2.24 Storey Shear ( Vi )
5.2.15 Moment-Resisting Frame
It is the sum of design lateral forces at all levels above
It is a frame in which members and joints are capable the storey under consideration.
of resisting forces primarily by flexure.
5.2.25 Weak Storey
5.2.15.1 Ordinary moment-resisting frame
It is one in which the storey lateral strength is less than
It is a moment-resisting frame not meeting special 80 percent of that in the storey above. The storey lateral
detailing requirements for ductile behaviour. strength is the total strength of all seismic force resisting
elements sharing the storey shear in the considered
5.2.15.2 Special moment-resisting frame
direction.
It is a moment-resisting frame specially detailed to
provide ductile behaviour and comply with the 5.3 General Principles and Design Criteria
requirements given in 1S 4326 or IS 13920 or 5.3.1 General Principles
SP 6(6).
5.3.1.1 Ground motion
5.2.16 Number of Storeys (n)
The characteristics (intensity, duration, etc) of seismic
Number of storeys of a building is the number of levels ground vibrations expected at any location depends
above the base. This excludes the basement storeys, upon the magnitude of earthquake, its depth of focus,
where basement walls are connected with the ground distance from the epicentre, characteristics of the path
floor deck or fitted between the building columns. But, through which the seismic waves travel, and the soil
it includes the basement storeys, when they are not so strata on which the structure stands. The random
connected. earthquake ground motions, which cause the structure
5.2.17 Principal Axes to vibrate, can be resolved in any three mutually
perpendicular directions. The predominant direction
Principal axes of a building are generally two of ground vibration is usually horizontal.
mutually perpendicular horizontal directions in plan
of a building along which the geometry of the building Earthquake-generated vertical inertia forces are to be
is oriented. considered in design unless checked and proven by
specimen calculations to be not significant. Vertical
5.2.18 P – A E#ect acceleration should be considered in structures with large
spans, those in which stability is a criterion for design,
It is the secondary effect on shears and moments of
or for overall stability analysis of structures. Reduction
frame members due to action of the vertical loads,
in gravity force due to vertical component of ground
interacting with the lateral displacement of building
motions can be particularly detrimental in cases of
resulting from seismic forces.
prestressed horizontal members and of cantilevered
5.2.19 Shear Wall members. Hence, special attention should be paid to the
effect of vertical component of the ground motion on
It is a wall designed to resist lateral forces acting in its
prestressed or cantilevered beams, girders and slabs.
own plane.
5.3.1.2 The response of a structure to ground
5.2.20 Soft Storey
vibrations is a function of the nature of foundation soil,
It is one in which the lateral stiffness is less than 70 materials, form, size and mode of construction of
percent of that in the storey above or less than 80 structures; and the duration and characteristics of
percent of the average lateral stiffness of the three ground motion. This standard specifies design forces
storeys above. for structures standing on rocks or soils which do not

58 NATIONAL BUILDING CODE OF JNDL4


settle, liquefy or slide due to loss of strength during taken into account, load combinations specified
ground vibrations. in 5.3.3.3 shall be considered.

5.3.1.3 The design approach adopted in this standard 5.3.1.6 Equipment and other systems, which are
is to ensure that structures possess at least a minimum supported at various floor levels of the structure, will
strength to withstand minor earthquakes (cDBE), be subjected to motions corresponding to vibration at
which occur frequently, without damage; resist their support points. In important cases, it may be
moderate earthquakes (DBE) without significant necessary to obtain floor response spectra for design
structural damage though some non-structural damage of equipment supports. For detail reference be made
may occur; and aims that structures withstand a major to good practice [6-1(5)]
earthquake (MCE) without collapse. Actual forces that
5.3.1.7 Additions to existing structures
appear on structures during earthquakes are much
‘greater than the design forces specified in this Code. Additions shall be made to existing structures only as
However, ductility, arising from inelastic material follows:
ibehaviour and detailing, and overstrength, arising from
a) An addition that is structurally independent
the additional reserve strength in structures over and
from an existing structures shall be designed
‘above the design strength, are relied upon to account
and constructed in accordance with the
for this difference in actual and design lateral loads.
seismic requirements for new structures.
Reinforced and prestressed concrete members shall be b) An addition that is not structurally independent
suitably designed to ensure that premature failure due from an existing structure shall be designed
to shear or bond does not occur, subject to the and constructed such that the entire structure
provisions of Part 6 ‘Structural Design, Section 5 conforms to the seismic force resistance
Concrete’. Provisions for appropriate ductile detailing
requirements for new structures unless the
of reinforced concrete members shall be in accordance
following three conditions are complied with:
with good practice [6- 1(4)].
1) The addition shall comply with the
In steel structures, members and their connections requirements for new structures;
should be so proportioned that high ductility is 2) The addition shall not increase the
obtained, vide SP 6(6), avoiding premature failure due seismic forces in any structural elements
to elastic or inelastic buckling of any type.
of the existing structure by more than
The specified earthquake loads are based upon post- 5 per cent unless the capacity of the
elastic energy dissipation in the structure and because element subject to the increased force is
of this fact, the provision of this Code for design, still in compliance with this standard; and
detailing and construction shall be satisfied even for 3) The addition shall not decrease the
structures and members for which load combinations seismic resistance of any structural
that do not contain the earthquake effect indicate larger element of the existing structure unless
demands than combinations including earthquake. reduced resistance is equal to or greater
5.3.1.4 Soil-structure interaction than that required for new structures.

The soil-structure interaction refers to the effects of 5.3.1.8 Change in occupancy


the supporting foundation medium on the motion of When a change of occupancy results in a structure
structure. The soil-structure interaction may not be being reclassified to a higher importance factor(1), the
considered in the seismic analysis for structures structure shall conform to the seismic requirements for
supported on rock or rock-like material. a new structure with the higher importance factor.
5.3.1.5 The design lateral force specified in this Code
5.3.2 Assumptions
shall be considered in each of the two orthogonal
horizontal directions of the structure. For structures The following assumptions shall be made in the
which have lateral force resisting elements in the two earthquake-resistant design of structures:
orthogonal directions only, the design lateral force shall a) Earthquake causes impulsive ground motions,
be considered along one direction at a time, and not in which are complex and irregular in character,
both directions simultaneously. Structures, having changing in period and amplitude each lasting
lateral force resisting elements (for example, frames, for a small duration. Therefore, resonance of
shear walls) in directions other than the two orthogonal the type as visualized under steady-state
directions, shall be analysed considering the load sinusoidal excitations, will not occur as it
combinations specified in 5.3.3.2. would need time to buildup such amplitudes.
Where both horizontal and vertical seismic forces are NOTE — However, there are exceptions where

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 59


r“’-

resonance-like conditions have been seen to occur two orthogonal horizontal dkection, EL in 5.3.3.1.1 and 5.3.3.1.2
between long distance waves and tall structures founded shall be replaced by (ELI &0.3 .ELY)or (ELY A 0.3 ELx).
on deep soft soils.
5.3.3.3 Design vertical earthquake load
b) Earthquake is not likely to occur simultaneously
When effects due to vertical earthquake loads are to
with wind or maximum flood or maximum
be considered, the design vertical force shall be
sea waves.
calculated in accordance with 5.3.4.5.
c) The value of elastic modulus of materials,
wherever required, may be taken as for static 5.3.3.4 Combination for two or three component motion
analysis unless a more definite value is 5.3.3.4.1 When responses from the three earthquake
available for use in such condition (see Part 6 components are to be considered, the responses due
‘Structural Design, Section 5 Concrete and to each components may be combined using the
Section 6 Steel’. assumption that when the maximum response from one
5.3.3 Load Combination and Increase in Permissible component occurs, the responses from the other two
Stresses component are 30 percent of their maximum. All
possible combinations of the three components (ELX,
5.3.3.1 Load combinations ELY and .ELZ)including variations in sign (plus or minus)
When earthquake forces are considered on a structure, shall be considered. Thus, the response due earthquake
these shall be combined as per 5.3.3.1.1 and 5.3.3.1.2 force (EL) is the maximum of the following three cases
where the terms DL, IL and EL stand for the response a) * ELX * 0.3 ELY* 0.3 EL=
quantities due to dead load, imposed and designated b) ~ ELY ~ (3.3 ELX& 0.3 ELZ
earthquake load respectively. >-..
c) * ELZ * 0.3 EL,* 0.3 EL Y
5.3.3.1.1 Load factors for plastic design of steel
Where x and y are two orthogonal directions and z is
structures
vertical direction.
In the plastic design of steel structures, the following
5.3.3.4.2 As an alternative to the procedure in 5.33.4.1,
load combinations shall be accounted for:
the response (EL) due to the combined effect of the
a) 1.7 (DL + IL) three components can be obtained on the basis of
b) 1.7 (DL & EL) ‘square root of the sum of the square (SRSS)’ that is
c) 1.3 (DL+ IL & EL)
EL= ~ (EL,)’+ (E~)2+ (E~)’
5.3.3.1.2 Partial safety factors for limit state design of
reinforced concrete andprestressed concrete structures NOTE — The combination procedure of 5.3.3.4.1 and 5.3.3.4.2
apply to the same response quantity (say, moment in a cohrmn
In the limit state design of reinforced and prestressed about its major axis, or storey shear in a frame) due to different
components of the ground motion.
concrete structures, the following load combinations
shall be accounted for: 5.3.3.4.3 When two component motions (say one
horizontal and one vertical, or only two horizontal)
a) 1.5 (DL + IL)
are combined, the equations in 5.3.3.4.1 and 5.3.3.4.2
b) 1.2 (DL+ IL & EL)
should be modified by deleting the term representing
c) 1.5 (DL * EL) the response due to the component of motion not being
d) 0.9 DL * 1.5 EL considered.
5.3.3.2 Design horizontal earthquake load 5.3.3.5 Increase in permissible stresses
5.3.3.2.1 When the lateral load resisting elements are 533.5.1 Increase in permissible stresses in materials
oriented along orthogonal horizontal direction, the
structure shall he designed for the effects due to full design When earthquake forces are considered along with other
earthquake load in one horizontal direction at time. normal design forces, the permissible stresses in material,
in the elastic method of design, maybe increased by one-
5.3.3.2.2 When the lateral load resisting elements are third. However, for steels having a definite yield stress,
not oriented along the orthogonal horizontal directions, the stress be limited to the yield stress; for steels without
the structure shall be designed for the effects due to a definite yield point, the stress will be limited to 80
full design earthquake load in one horizontal direction percent of the ultimate strength orO.2 percent proof stress,
plus 30 percent of the design earthquake load in the whichever is smalle~ and that in prestressed concrete
other direction. members, the tensile stress in the extreme fibres of the
NOTE — For instance, the building should be designed for concrete may be permitted so as not to exceed two-thirds
(* ELX* o.3 EL,) as well as (+ 0.3 E-LX
* EL), where x and y are of the modulus of ntpture of concrete.

60 NATIONAL BUILDING CODE OF INDIA


5.3.3.5.2 Increase in allowable pressure in soils while locating new settlements or important projects.
Otherwise, this aspect of the problem needs to be
When earthquake forces are included, the allowable
investigated and appropriate methods of compaction
bearing pressure in soils shall be increased as per
or stabilization adopted to achieve suitable N values
Table 1, depending upon type of foundation of the
as indicated in Note 3 under Table 30. Alternatively,
structure and the type of soil.
deep pile foundation may be provided and taken to
In soil deposits consisting of submerged loose depths well into the layer which is not likely to
sands and soils falling under classification SP with liquefy. Marine clays and other sensitive clays are
standard penetration N values less than 15 in seismic also known to liquefy due to collapse of soil structure
Zones III, IV, V and less than 10 in seismic Zone II, and will need special treatment according to site
the vibration caused by earthquake may cause condition.
liquefaction or excessive total and differential NOTE — Specialist literature maybe referred for determining
settlements. Such sites should preferably be avoided liquefaction potential of a site.

Table 30 Percentage of Permissible Increase in Allowable Bearing


Pressure or Resistance of Soils
(Clause 5.3.3.5.2)

S1 Foundation Type of Sd Makdy Constituting the Foundation


No. — \
.
Type I Rock or Hard Soil: Type II Medium Soils Type III Soft Soifs: Alf
Well graded gravel and sand All soils with N between soils other than SP1)
~avel mixtures with or without 10 art 30, and poorly with N<10
clay binder, and clayey sartds graded sands or gravelly
poorly graded or sand clay sands with fittle or no
tUiXhU7X (GB, CW, SB, SW aod fis= (sP’)) with N> 15
SC~) having2)above 30, where N
is the standard penetration value
(1) (2) - (3) (4) (5)

O Piles passing through any soil but 50 50 50


resting on solid type I
ii) Piles not covered under item (i) — 25 25
iii) Raft foundations 50 50 50
iv) Combined isolated RCC footing with 50 25 —
tie beams
v) Isolated RCC footing without tie beams, 50 25 —
or unreinforcedstrip foundations
vi), Well foundations 50 25 25

NOTES
1 The allowable bearing pressure shall be determined in accordance with good practice [6-1(6)].
2 If any increase in bearing pressure has already been permitted for forces other than seismic forces, the totat increase in aflowable
bearing pressure when seisrrrtcforce is afso included shall not exceed the limits specified above.
3 Desirable minimum field~alues of N — If soils of smaller N-values are met, compacting may be,adopted to achieve these values or
deep pile foundations going to stronger strata should be used.
4 The values of N (corrected vatues) are at the founding level and the allowable bearing pressur$ shafl be determined in accordance
with good practice [6-1(6)].

SeismicZone Level Depth Below Ground N-Values ‘Remark


m
<5 15
III, N and V For values of depths between 5 m
>10 25
55 and 10 m, linear interpolation is
15
fI (for important structures only) >10 recommended.
20 1

5 The piles should be designed for lateral loads neglecting lateral resistance of soil layers liable to fiquefy.
6 Accepted standard [6-1(7)] and good practice [6-1(8)] may also be referred.
7 Isolated R.C.C. footing without tie beams, or unreinforced strip foundation shafl not be permitted its soft soils with N<1O.

1) See accepted standard [6-1(7)].


2).’h Qonduractice [6-1(8)1.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 61


5.3.4 Design Spectrum for dynamic analysis, the value of Ah as defined
in 5.3.4.2 for each mode shall be determined using—the
5.3.4.1 For the purpose of determining seismic forces,
natural period of vibration of that mode.
the country is classified into four seismic zones as
shown in Fig. 11. 5.3.4.4 For underground structures and foundations
at depths of 30 m or below, the design horizontal
5.3.4.2 The design horizontal seismic coefficient Ah
acceleration spectrum value shall be taken as half the
for a structure shall be determined by the following
value obtained from 5.3.4.2. For structures and
expression:
foundations placed between the ground level and 30 m
— ZI Sa depth, the design horizontal acceleration spectrum
4 —
2 Rg value shall be linearly interpolated between Ah and
0.5 All, where Ah is as specified in 5.3.4.2. ?
Provided that for any structure with T20.1 see, the
value of A ~ will not be less than 2/2 whatever be the 5.3.4.5 The design acceleration spectrum for vertical
value of J/l? motions, when required, may be taken as two-thirds
where of the design horizontal acceleration spectrum
specified in 5.3.4.2. ;
z= Zone factor given in Table 31, is for the
maximum considered earthquake (MCE) Figure 12 shows the proposed 5 percent spectra for
kL
and service life of structure in a zone. The rocky and soils sites and Table 32 gives the multiplying
factor 2 in the denominator of — > is used so factors for obtaining spectral values for various other
y
as to reduce the maximum considered clampings.
i,

earthquake (MCE) zone factor to the factor For Rocky, or hard soil sites
for design basis earthquake (DBE).
Zone factor for some important towns are s 1+15T; O.OO<TSO.1O
—a = 2.50 O.1O<T <0.40
given at Annex J. g { 1.00IT 0.40< T <4.00
I = Importance factor, depending upon the
functional use of the structures, characterised For Medium soil sites
by hazardous consequences of its failure,
s 1+15T; O.OO<T<O.1O
post-earthquake functional needs, historical —a = 2.50 O.1OST<O.55
value, or economic importance (Table 35). g { L361T 0.55< T s 4.00
R= Response reduction -factor, depending on
the perceived seismic damage performance For Soft soil sites
of the structure, characterized by ductile
s 1+15T; O.OOSTSO.1O
or brittle deformations. However, the —a = 2.50 O.1O<TSO.67
ratio (l/R) shall not be greater than 1.0 g { 1.671T 0.67 S T <4.00
(Table 36). The values of R for buildings
are given in Table 36. Table 32 Multiplying Factors for Obtaining
s/g=
it Average response acceleration coefficient Values for Other Damping
for rock or soil sites as given by Fig. 12 and (Clause 5.3.4.2)
Table 32 based on appropriate natural
periods and damping of the structure. These Damping O 2 5 7 10 15 20 25 30
percent
curves represent free field ground motion.
Factors 3.20 1.40 1.00 0.90 0.80 0.70 0.60 0.55 0.50
NOTE — For various types of structures, the values
of Importance Factor Z,Response Reduction Factor 1?,
and damping values are given in the respective parts 5.3.4.6 In case design spectrum is specifically
of this standard. The method (empirical or otherwise) prepared for a structure at a particular project site, the
to calculate the natural periods of the structure to be
same may be used for design at the discretion of the
adopted for evaluating S,/g is also given in the
respective parts of this Code. project authorities.

Table 31 Zone Factor, Z 5.4 Buildings


(Clause 5.3.4.2) 5.4.1 Regular and Irregular Configuration

Seismic Zone II III IV v To perform well in an earthquake, a building should


Seismic Intensity Low Moderate Severe Very Severe possess four main attributes, namely, simple and
z 0.10 0.16 0.24 0.36 regular configuration, and adequate lateral strength,
stiffness and ductility. Buildings having simple regular
5.3.4.3 Where a number of modes are to be considered in plan as well as in elevation, suffer much less damage

62 NATIONAL BUILDING CODE OF INDIA

+7
L
TYPE I (ROCK, OR HARD SOIL)

TYPE II (MEDIUM SOIL)


TYPE Ill (SOFT SOIL)

\ ~-~-~.

I I I I I I 1

0.O 0.5 1.0 1.5 2.0 2.5 3*O 3“5 4“0


PERIOD(S)

FIG. 12 RESPONSESPECTRAFOR ROCK AND SOIL SIGHT FOR 5 PERCENTDAMPING

than buildings with irregular configurations. A building Table 34 Definition of Irregular Buildings —
shall be considered as irregular for the purposes of this Vertical Irregularities (Fig. 14)
standard, if at least one of the conditions given (Clause 5.4.1)
in Tables 33 and 34 is applicable.
S1 No. Irregularity Type and Description
Table 33 Definitions of Irregular Buildings —
i) a) Sti@ess Irregularity — Soft Storey
Plan Irregularities (Fig. 13)
A soft storey is one in which the lateral stiffness is less
(Clause 5.4.1) than 70 percent of that in the storey above or less than
80 percent of the average lateral stiffness of the three storeys
... m.

Irregularity Type and Description above.


S1 No,
i) Torsion Irregularity b) Stij%ess Irregularity — Extreme SOP Storey
To be considered when floor diaphragms are rigid in their An extreme soft storey is one in which the lateral stiffness
own plan in relation to the vertical structural elements that is less than 60 percent of that in the storey above or less
resist the lateral forces. Torsional irregularity to be than 70 percent of the average stiffness of the three storeys
considered to exist when the maximum storey drift, above. For example, buildings on STILTS will fall under
computed with design eccentricity, at one end of the this category.
structures transverse to an axis is more than 1.2 times the ii) Mass Irregularity
average of the storey drifts at the two ends of the structure. Mass irregularity shall be considered to exist where the
ii) Re-entrant Corners seismic weight of any storey is more than 200 percent of
Plan configurations of a structure and its lateral force resisting that of its adjacent storeys. The irregularity need not be
system contain re-entrant comers, where both projections of considered in case of roofs.
the structure beyond the re-entrant comer are greater than 15 iii) Vertical Geometric Irregulari~
percent of its plan dimension in the given direction. Vertical geometric irregularity shall be considered to exist
iii) Diaphragm Discontinuiv where the horizontal dimension of the lateral force resisting
Diaphragms with abrupt discontinuities or variations in system in any storey is more than 150 percent of that in its
stiffness, including those having cut-out or open areas greater adjacent storey.
than 50 percent of the gross enclosed diaphragm area, or iv) In-Plane Discontinuity in Vertical Elements Resisting
changes in effective diaphragm stiffness of more than 50 Lateral Force
percent from one storey to the next. An in-plane offset of the lateral force resisting elements
iv) Out- Of-
Plane Ofsets greater than the length of those elements.
Discontinuities in a lateral force resistance path, such as out- v) Discontinuity in Capacity — Weak Strorey
of-plane offsets of vertical elements. A weak storey is one in which the storey lateral strength is
v) Non-parallel Systems less than 80 percent of that in the storey above. The storey
The vertical elements resisting the lateral force are not lateral strength is the total strength of all seismic force
parallel to or symmetric about the major orthogonal axes or resisting elements sharing the storey shear in the considered
the lateral force resisting elements. direction.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 65


VERTICAL COMPONENTS OF \ HEAVY
SEISMIC RESISTING SYSTEM MASS

L ————
————
————
-1
FLOOR
\l
I
L! I A2
L —-—. ---- -——— J

Al 1 7
13A TORSIONAL IRREGULARITY

I__ /
/VL >0.15-0.20 A/L >0.15-0.20 A
‘1
L A/L >0.15-0.20

A
1
t

I + Al

T L2
M ~

13 B RE - ENTRANT CORNER

— Continued
FIG. 13 PLANIRREGULARITIES

66 NATIONAL BUILDING CODE OF INDIA


MASS RESISTANCE ECCENTRICITY

I
I
RIGID I
DIAPHRAGM ;
OPE
I
\ 1 0
%- \ --- I FLEXIBLE /
-
-1 DIAPHRAGM
e

VERTICAL COMPONENTS OF SEISMIC RESISTING


SYSTEM

OPENING

FLOOR

13 C DIAPHRAGM DISCONTINUITY

SHEAR WALL

*
-@

BUILDING SECTION

WALL

13 D OUT -OF - PLANE OFFSETS

~
I
SHEAR WALL

13 E NON - PARALLELSYSTEM

FIG. 13 PLAN IRREGULARITIES

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 67


STOREY STIFFNESS
FOR THE BUILDING
% 4

I ———
I
B ———

I -——

-——
SOFT STOREY WHEN
1 ——.

ki<().7ki+l
I —.—
k3
-—- I kj+l+ki+z+ki+s
1 OR ki<o.s( )
—--
k2 3
. ——— I L 1
I
k1
1

14A STIFFNESS IRREGULARITY

SEISMIC
-HEAVY WEIGHT
/ MASS
/
I
w n-1
1 w n-2
A A

w2
\ w 1

. MASS IRREGULARITY
MASS RATIO
WHENt Wi>2.0Wi -1
or Wi>2@OVVi+l

14 B MASS IRREGULARITY

FIG. 14 VERTICALIRREGULARITIES
— Continued

.
A ‘“

.
.<,.,%
pA--

T
u
A
r /L>o,l
A

l---!
--!
SHEAR WALL

L2--4 L~2--l
14 C VERTICAL GEOMETRIC IRREGULARITY, WHEN L2 >1.5 L,

STOREY STRENGTH
(LATERAL)
H

Fn
!
Fn. I
1
Fn.2
I I
UPPER
{ FLOOR 1

I F3

a F2
b 1
FI
LOWER
11 FLOOR 14 E WEAK STOREY,
WHEN Fj ~ 0.8 Fi +1
b

14 D IN - PLANE DISCONTINUITY VERTICAL ELEMENTS


RESISTING LATERAL FORCE, WHEN b > a

FIG. 14 VERTICALIRREGULARITIES

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 69


5.4.2 Importance Factor I and Response Reduction Table 36 Response Reduction FactorlJ R, for
Factor R Building Systems

The minimum value of importance factor, I, for (Clauses 5.3.4.2 and 5.4.2)
different building systems shall be as given in Table 35.
S1 Lateral Load Resisting System R
The response reduction factor, l?, for different building No.
svstems
* shall be as given in Table 36. Building Frame Systems

5.4.3 Design Imposed Loads for Earthquake Force i) Ordinary RC Moment-Resisting Frame (OMRF)2) 3.0
ii) Special RC Moment-Resisting Frame (SMRF)3) 5.0
Calculation iii) Steel Frame with
a) Concentric Braces 4.0
5.4.3.1 For various loading classes as specified in b) Eccentric Braces 5.0
IS 875 @rt 2), the earthquake force shall be calculated iv) Steel Moment Resisting Frame designed as per 5.0
for the full dead load plus the percentage of imposed SP: 6(6)
load as given in Table 37. Building with Shear Walls 4)
v) Load Bearing Masonry Wall Buildings 5)
5.4.3.2 For calculating the design seismic forces of a) Unreinforced 1.5
the structure, the imposed load on roof need not be b) Reinforced with horizontal RC Bands 2.5
considered. c) Reinforced with horizontal RC bands and 3.0
vertical bars at comers of rooms and jambs
5.4.3.3 The percentage of imposed loads given of openings
vi) Ordinary Reinforced Concrete Shear Walls c) 3.0
in5.3.3.l and 5.3.3.2 shall also be used for ‘Whole
vii) Ductile Shear Walls 7) 4.0
frame loaded’ condition in the load combinations
Buildings with Dual Systems 8)
specified in5.3.3.l.l and5.3.3.l.2 where the gravity
viii) Ordinary Shear Wall with OMRF 3.0
loads are combined with the earthquake loads [that is
ix) Ordinary Shear Wall with SMRF 4.0
in load combinations (a) in 5.3.3.1.1, and (b) x) Ductile Shear Wall with OMRF 4.5
in 5.3.3.1.2]. No further reduction in the imposed load xi) Ductile Shear Wall with SMRF 5.0
will be used as envisaged in 3 for number of storeys
above the one under consideration or for large spans 1,The above values of response reduction factors are to be used for
of beams or floors. buildings with lateral load resisting elements, and not just for the
lateral load resisting elements built in isolation.
5.4.3.4 The proportions of imposed load indicated 2, OMRF are those designed and detailed as per IS 456 or IS 800
above for calculating the lateral design forces for but not meeting ductile detailing requirement as per IS 13920.

earthquakes are applicable to average conditions. J) SMRF defined in 4.15.2.

Where the probable loads at the time of earthquake 4, Buildings with shear walls also include buildings having shear
walls and frames, but where
are more accurately assessed, the designer may alter
a) frames are not designed to carry lateral loads, or
the proportions indicated or even replace the entire
b) frames are designed to carry lateral loads but do not fulfil
the requirements of ‘duals ystems’.
Table 35 Importance Factors, Z
5, Reinforcement should be as per IS 4326.
(Clauses 5.3.4.2 and 5.4.2) G)prohibited in Zones IV and V.
7, Ductile shear walls are those designed and detailed as per IS 13920
S1 St~cture Importance
No. Factor 8, Buildings with dual systems consist of shear walls (or braced
frames) and moment resisting frames such that
i) Important service and community buildings, 1.5
a) the two systems are designed to resist the total design
such as hospitals; schools; monumental
force in proportion to their lateral stiffness considering
structures; emergency buildings like telephone
exchange, television stations, radio stations, the interaction of the dual system at all floor levels;
railway stations, fire station buildings; large and
community halls like cinemas, assembly halls b) the moment resisting frames are designed to
and subway stations, power stations. independently resist at least 25 percent of the design
seismic base shear.
ii) All other buildings. 1.0

NOTES Table 37 Percentage of Imposed Load to be


1 The design engineer may choose values of importance factor 1 Considered in Seismic Weight Calculation
greater than those mentioned above.
(Clause 5.4.3.1)
2 Buildings not covered in S1 No. (i) and (ii) above may be
designed for higher value of 1, depending on economy, strategy
Imposed Uniformity Distributed Percentage of Imposed
considerations like multi-storey buildings having several
Floor Loads (kN/sq.m) Load
residential units.
3 This does not apply to temporary structures like excavations, Up to and including 3.0 25
scaffolding etc of short duration. Above 3.0 50

70 NATIONAL BUILDING CODE OF INDIA


imposed load proportions by the actual assessed load. of vibration (T,), in seconds, of a moment-resisting
In such cases, where the imposed load is not assessed frame building without brick infill panels may be
as per 5.4.3.1 and 5.4.3.2 only that part of imposed estimated by the empirical expression:
load, which possesses mass, shall be considered.
Lateral design force for earthquakes shall not be T, = 0.075 h“”’s for RC Frame Building
calculated on contribution of impact effects from
imposed loads. = ().085 ho”” for Steel Frame Building

5.4.3.5 Other loads apart from those given above (for where
example, snow and permanent equipment) shall be
h = Height of building, in metres. This excludes
considered as appropriate.
the basement storeys, where basement walls
5.4.4 Seismic Weight are connected with the ground floor deck or
fitted between the building columns. But, it
5.4.4.1 Seismic weight offloors
includes the basement storeys, when they are
The seismic weight of each floor is its full dead load not so connected.
plus appropriate amount of imposed load, as specified
5.4.6.2 The approximate fundamental natural period
in 5.4.3.1 and 5.4.3.2. While computing the seismic
of vibration (T,), in seconds, of all other buildings,
weight of each floor, the weight of columns and walls
including moment-resisting frame buildings with brick
in any storey shall be equally distributed to the floors
infill panels, may be estimated by the empirical
above and below the storey.
expression:
5.4.4.2 Seismic weight of building
0.09 h
The seismic weight of the whole building is the sum
‘a= &
of the seismic weights of all the floors.
where
5.4.4.3 Any weight supported in between storeys shall
be distributed to the floors above and below in inverse h= Height of building, in metres, as defined
proportion to its distance from the floors. in 5.4.6.1; and
5.4.5 Design Luteral Force d= Base dimension of the building at the plinth
level, in metres; and along ti~ considered
5.4.5.1 Buildings and portions thereof shall be designed direction of the lateral force.
and constructed, to resist the effects of design lateral
force specified in 5.4.5.3 as a minimum. 5.4.7 Distribution of Design Force

$.4.5.2 The design lateral force shall f~st be computed 5.4.7.1 Vertical distribution of base shear to different
for the building as a whole. This design lateral force jloor levels
shall then be distributed to the various floor levels.
The design base shear (VB ) computed in 5.4.5.3 shall
The overall design seismic force thus obtained at each
be distributed along the height of the building as per
floor level, shall then be distributed to individual lateral
the following expression:
load resisting elements depending on the floor
diaphragm action.
5.4.5.3 Design seismic base shear— The total design
lateral force or seismic base shear (V~) along any
principal direction shall be determined by the following
expression: where

v, = ~w Qi = Design lateral force at floor i,


where W,= Seismic weight of floor i,
Ab = Design horizontal acceleration spectrum hi = Height of floor i measured from base, and
value as per 5.3.4.2, using the fundamental n = Number of storeys in the building is the
natural period as per 5.4.6 in the considered number of levels at which the masses are
direction of vibration; and located.
W = Seismic weight of the building as 5.4.7.2 Distribution of horizontal design lateral force
per 5.4.4.2. to diferent lateral force resisting elements
$.4.6 Fundamental Natural Period
5.4.7.2.1 In case of buildings whose floors are capable
5.4.6.1 The approximate fundamental natural period of providing rigid horizontal diaphragm action, the total

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 71


shear in any horizontal plane shall be distributed to of dynamic analysis of steel and reinforced concrete
the various vertical elements of lateral force resisting buildings, respectively.
system, assuming the floors to be infinitely rigid in
5.4.8.3 Time history method
the horizontal plane.
Time history method of analysis, when used, shall be
5.4.7.2.2 In case of building whose floor diaphragms
based on an appropriate ground motion and shall be
cannot be treated as infinitely rigid in their own plane,
performed using accepted principles of dynamics.
the lateral shear at each floor shall be distributed to
the vertical elements resisting the lateral forces, 5.4.8.4 Response spectrum method
considering the in-plane flexibility of the diaphragms.
Response spectrum method of analysis shall be
NOTES performed using the design spectrum specified
1 A floor diaphragm shatl be considered to be flexible, if it by 5.3.4.2, or by a site-specific design spectrum
deforms such that the maximum lateral displacement measured
mentioned in 5.3.4.6.
from the chord of the deformed shape at any point of the
diaphragm is more than 1.5 times the average displacement of 5.4.8.4.1 Free vibration analysis
the entire diaphragm,
2 Reinforced concrete monolithic slab-beam floors or those Undamped free vibration analysis of the entire building
consisting of Prefabricated/Precast elements with topping shall be performed as per established methods of
reinforced screed can be taken a rigid diaphragms.
mechanics using the appropriate masses and elastic
5.4.8 Dynamic Analysis stiffness of the structural system, to obtain natural
periods (T) and mode shapes {@} of those of its modes
5.4.8.1 Dynamic analysis shall be performed to obtain
of vibration that need to be considered as per 5.4.8.4.2.
the design seismic force, and its distribution to different ,,..
levels along the height of the building and to the various 5.4.8.4.2 Modes to be considered
lateral load resisting elements, for the following
The number of modes to be used in the analysis should
buildings:
be such that the sum total of modal masses of all modes
a) Regular buildings — Those greater than 40 m considered is at least 90 percent of the total seismic
in height in Zones IV and V, and those greater mass and t-nksing mass correction beyond 33 percent.
than 90 m in height in Zones II and III. If modes with natural frequency beyond 33 Hz are to
Modelling as per 5.4.8.4.5 can be used. be considered, modal combination shall be carried out
b) Irregular buildings (as dejlned in 5.4.1) — only for modes up to 33 Hz. The effect of higher modes
All framed buildings higher than 12 m in shall be included by considering missing mass
Zones IV and V, and those greater than 40 m correction following well established procedures.
in height in Zones 11and 111. 5.4.8.4.3 Analysis of building subjected to design
The analytical model for dynamic analysis of buildings forces
with unusual configuration should be such that it The building may be analysed by accepted principles
adequately models the types of irregularities present of mechanics for the design forces considered as static
in the building configuration. Buildings with plan forces.
irregularities, as defined in Table 33 (as per 5.4.1),
cannot be modelled for dynamic analysis by the method 5.4.8.4.4 Modal Combination
given in 5.4.8.4.5 The peak response quantities (for example, member
NOTE — For irregular buildings, lesser than 40 m in height in forces, displacements, storey forces, storey shears and
Zones II and III, dynamic analysis, even though not mandatory, base reactions) shall be combined as per Complete
is recommended.
Quadratic Combination (CQC) method.
5.4.8.2 Dynamic analysis may be performed either by
the Time History Method or by the Response Spectrum a.=
Method. However, in either method, the design base
shear (VB ) shall be compared with a base shear (VB )
where
calculated using a fundamental period T~, where T, is
as per 5.4.6. Where V~ is less than V~, all the response r = Number of modes being considered,
quantities (for example, member forces, displacements, Ai = Response quantity in i th mode,
storey forces, storey shears and base reactions) shall
Pij= Cross-modal coefficient i (including sign),
be multiplied by ~/V~ ).
and
5.4.8.2.1 The value of damping for buildlngs may be A, = Response quantity in mode j (including
taken as 2 and 5 percent of the critical, for the purposes sign).

72 NATIONAL BUILDING CODE OF INDIA


Wi = Seismic weight of floor i.
852 (1+ /?) ~’”
b) Modal Participation Factors — The modal
‘i’ = (1-/32)2 +452p(l+ p)’
participation factor (PK) of mode k is given
< = Modal damping ratio (in fraction) as by
specified in 5.4.8.2.1,
~ = Frequency ratio= co~mi ~Y @ik
COi= circular frequency in ith mode, and PK = ‘=’
@j = circular frequency in jth mode. ~Y (@ikj’
i=l

Alternatively, the peak response quantities may be


combined as follows: c) Design lateral Force at Each Floor in Each
Mode — The peak lateral force (Qi~) at floor
a) If the building does not have closely-spaced i in mode k is given by
modes, then the peak response quantity (k)
due to all modes considered shall be obtained Qik= A. 4. p. Wj
as
where

A.=
.. Design horizontal acceleration spectrum value
as per 5.3.4.2 using the natural period of
vibration (T~) of mode k.
where
c) Storey Shear Forces in Each Mode — The
A, = Absolute value of quantity in mode k. peak shear force (ViK) acting in storey i in
b) If the building has a few closely-spaced mode k is given by
modes (see 5.3.3.2), then the peak response
quantity (2*) due to these modes shall be
obtained as

d) Storey Shear Forces due to All Modes


Considered — The peak storey shear force
(V.) in storey i due to all modes considered is
where the summation is for the closely-spaced obtained by combining those due to each
modes only. This peak response quantity due to mode in accordance with 5.4.8.4.4.
the closely spaced modes (1’) is then combined e) Lateral Forces at Each Storey due to All
with those of the remaining well-separated modes Modes Considered — The design lateral
by the method described in 5.4.8.4.4 (a). forces, F,OO~and Fi, at roof and at floor i:
5.4.8.4.5 Buildings with regular, or nominally F roof = V,w~ and
irregular, plan configurations may be modelled as a
system of masses lumped at the floor levels with each Fi = Vi - Vi+l
mass having one degree of freedom, that of lateral
5.4.9 Torsion
displacement in the direction under consideration. In
such a case, the following expressions shall hold in 5.4.9.1 Provision shall be made in all buildings for
the computation of the various quantities: increase in shear forces on the lateral force resisting
elements resulting from the horizontal torsional
a) Modal Mass — The modal mass (M~) of mode
moment arising due to eccentricity between the centre
k is given by
of mass and centre of rfgidity. The design forces
calculated as in 5.4.8.4.5 are to be applied at the centre
of mass appropriately displaced so as to cause design
eccentricity (5.4.9.2) between the displaced centre of
mass and centre of rigidity. However, negative
torsional shear shall be neglected.

where 5.4.9.2 The design eccentricity, ed to be used at floor


i shall be taken as
g = Acceleration due to gravity,
~,, = Mode shape coefficient at floor i in mode k, 1.5 e,, +0.05 ~
and e~ = or e,i – 0.05 bi
{

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 73


whichever of these gives the more severe effect There shall be no drift limit for single storey building
in the shear of any frame where which has been designed to accommodate storey drift.
edi = static eccentricity at floor r’defined as the 5.4.11.2 Deformation compatibility of non-seismic
distance between centre of mass and centre members
of rigidity and
b, = floor plan dimension of floor i, perpendicular For building located in seismic Zones IV and V, it shall
be ensured that the structural components, that are not
to the direction of force.
a part of the seismic force resisting system in the
NOTE — The factor 1.5 represents dynamic
amplification factor, while the factor 0.05 represents direction under consideration, do not lose their vertical
the extent of accidental eccentricity. load-carrying capacity under the induced moments
resulting from storey deformations equal to R times
5.4.9.3 In case of highly irregular buildings analysed
the storey &placements calculated as per 5.4.11.1,
according to 5.4.8.4.5, additive shears will be
where R is specified in Table 36.
superimposed for a statically applied eccentricity of
& 0.05bi with respect to the centre of rigidity. NOTE — For instance, consider a flat-slab building in which
lateral load resistance is provided by shear walls. Since the
5.4.10 Buildings with Soft Storey lateral load resistance of the slab-column system is smatl, these
are often designed only for the gravity loads, while all the
5.4.10.1 In case buildings with a flexible storey, such seismic force is resisted by the shear walls. Even though the
as the ground storey consisting of open spaces for slabs and columns are not required to share the Iaterat forces,
these deform with rest of tbe structure under seismic force.
parking that is stilt buildings, special arrangement
The concern is that under such deformations, the slab-column
needs to be made to increase the lateral strength and system should not lose its verticat load capacity.
stiffness of the soft/open storey. —
5.4.11.3 Separation between adjacent units
5.4.10.2 Dynamic analysis of building is earned out
including the strength and stiffness effects of infills Two adjacent buildings, or two adjacent units of the
and inelastic deformations in the members, particularly, same building with separation joint in between shall
those in the soft storey, and the members designed be separated by a distance equal to the amount R times
accordingly. the sum of the calculated storey displacements as
per 5.4.11.1 of each of them, to avoid damaging contact
5.4.10.3 Alternatively, the following design criteria when the two units deflect towards each other. When
are to be adopted after carrying out the earthquake floor levels of two similar adjacent units or buildings
analysis, neglecting the effect of infill walls in other
are at the same elevation levels, factor R in this
storeys: requirement may be replaced by R/2.
a) the columns and beams of the soft storey are
5.4.12 Miscellaneous
to be designed for 2,5 times the storey shears
and moments calculated under seismic loads 5.4.12.1 Founalztions
specified in the other relevant clauses; or,
The use of foundations vulnerable to significant
b) besides the columns designed and detailed for differential settlement due to ground shaking shall be
the calculated shears and moments, shear avoided for structures in seismic Zones III, IV and V.
walls placed symmetrically in both directions In seismic Zones IV and V, individual spread footings
of the building as far away from the centre of or pile caps shall be interconnected with ties,
the building as feasible; to be designed (see 5.2.3.4.1 of IS 4326) except when individual
exclusively for 1.5 times the lateral shear force spread footings are directly supported on rock. All ties
calculated as before. shall be capable of carrying, in tension and in
5.4.11 Deformations compression, an axial force equal to A~/4 times the
larger of the column or pi% cap load, in addition to the
5.4.11.1 Storey drifi limitation otherwise computed forces. Here, Ah is as per 5.3.4.2.
The storey drift in any storey due to the minimum 5.4.12.2 Cantilever projections
specified design lateral force, with partial load factor
of 1.0, shall not exceed 0.004 times the storey height. 5.4.12.2.1 Vertical projections

For the purposes of displacement requirements only Tower, tanks, parapets, smoke stacks (chimneys) and
(that is, in 5.4.11 .1,5.4.11.2 and 5.4.11.3 only), it is other vertical cantilever projections attached to
permissible to use seismic force obtained from the buildings and projecting above the roof, shall be
computed fundamental period (7’) of the building designed and checked for stability for five times the
without the lower bound limit on design seismic force design horizontal seismic coefficient Ah specified
specified in 5.4.8.2. in 5.3.4.2. In the analysis of the building, the weight

74 NATIONAL BUILDJNG CODE OF INDIA


of these projecting elements will be lumped with the B, (degrees) — Roof slope,
roof weight. SO(pascals) — Snow load on ground.
5.4.12.2.2 Horizontal projection Si (pascals) — Snow load on roofs.

All horizontal projections like cornices and balconies 6.3 Snow Load in Roof(s)
shall be designed and checked for stability for five
6.3.1 The minimum design snow load on a roof area
times the design vertical coefficient specified in 5.3.4.5.
or any other area above ground which is subjected to
5.4.12.2.3 The increased design forces specified snow accumulation is obtained by multiplying the snow
in 5.4.11.2.1 and 5.4.12.2.2 are only for designing the load on ground, SOby the shape coefficient V, as
projecting parts and their connections with the main applicable to the particular roof area considered:
structures. For the design of the main structure, such
s=~so
increase need not be considered.
where
5.4.12.3 Corrrpound walls
s= Design snow load in Pa on plan area of roof,
Compound walls shall be designed for the design
horizontal coefficient Ah with Importance Factor I = 1.0 P= Shape coefficient (see 5.4), and
specified in 6.4.2 so = Ground snow load in Pa (1 Pa=l N/m*)

5.4.12.4 Connections between parts NOTE — Ground snow load at any place depends on the
critical combination of the maximum depth of undisturbed
All parts of the building, except between the separation aggregate cumulative snow fall and its average density. In
sections, shall be tied together to act as integrated single due course the characteristic snow load on ground for
different regions will be included based on studies. TM such
unit. All connections between different parts, such as, time the users of this code are advised to contact either Snow
beams to columns and columns to their footings, should and Avalanches Study Establishment (Defence Research and
be made capable of transmitting a force, in all possible Development Organization), Manali (HP) or Indian
directions, of magnitude ( Qi/Wi) times but not less than Meteorological Department (IMD), pane in the absence of
any specific information for any location.
0.05 times the weight of the smaller part or the total
of dead and imposed load reaction. Frictional 6.4 Shape Coefficients
resistmce shall not be relied upon for fulfilling these
6.4.1 General Principles
requirements.
In perfectly calm weather, falling snow would cover
6 SNOW LOAD roofs and the ground with a uniform blanket of snow,
6.1 This clause deals with snow loads on roofs of and the design snow load could be considered as a
buildings. Roofs should be designed for the actual load uniformly distributed load. Truly uniform loading
due to snow or for the imposed loads specified in 3 conditions, however, are rare and have usually only
whichever is more severe. been observed in areas that are sheltered on all sides
by high trees, buildings, etc. In such a case, the shape
NOTE — Mountainous regions in northern parfs of India are
coefficient would be equal to unity.
subjected to snow fafl.

In India, part of Jammu and Kashmir (Baramulah Inmost regions, snow-falls are accompanied or followed
District, SrinagarDistrict, Anantnag District and Ladakh by winds. The winds will re-distribute the snow, and on
District); Punjab and Himachal Pradesh (Chamba, Kulu some roofs especially multilevel roofs, the accumulated
Kinnaur District, Mahasu District, Mandi District, drift load may reach a mdltiple of the ground load. Roofs
Sirrnur District and Simla District); and Uttaranchal which are sheltered by other buildings, vegetation, etc,
(Debra Dun District, Tehri Garhwal District, Ahrtora may collect more snow load than the ground level. The
District and Nainital District) experience snow fall of phenomenon is of the sade nature as that illustrated for
varying depths two or three times in a year. multi-level roofs in 6.4.2.4.

So far sufficient data are not available to determine


6.2 Notations
the shape coefficient on a statistical basis. Therefore,
(Dimensionless) — Nominal values of the shape a nominal value is given. A representative sample of
coefficients, taking tin account snow draft, sliding roofs is shown in 6.4.2. However, in special cases such
snow, etc, with subscripts, if necessary. as strip loading, cleaning of the roof periodically by
li (metres) — Horizontal dimension with numerical deliberate heating of the roof, etc, have to be treated
subscripts, if necessary. separately.

hi (metres) — Vertical dimensions with numerical The distribution of snow in the direction parallel to
subscripts, if necessary. the caves is assumed to be uniform.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS. FORCES AND EFFECTS 75


6.4.2 Shape Coefficients for Selected Types of Roofs

6.4.2.1 Simple Flat and Simple Pitched Roofs


Monopitch Roofs (Positive Roof Slope)’)

@
F1

P P
t

0“< p~ 3(yJ
I. J*= PI=O.8
I

E
IJl = 0.8
15 °c13530” P*
‘08+’
4%)
::%%)
-.

30°C PS 6@ P,= —
0.8 (60#
)
M,= o<8 60 -p
30 ()

--~--
~> 60° IJl iJ2 =IJl=o

/m
=0

6.4.2.2 Simple or Multiple Pitched Roofs Two-Span or Multispan


(Negative Roof Slope) Roofs
-. ,/ -
‘\ / /’
13 \/ I% /’ /

F$’+1 P

#31;132

IJ1= 0.8(30+P P, =o.8(30+~

E
00<$<30” — —
30 ) 30 )
w, = 0.8 IJl = 0.8
IJ2 =1.6 lJ2=l.6
3VCi3 c 60”
P, =(+!22 )
30
IJ2 =1.6 IJ2 =1.6
~> 60”
I- Jl=o IJj=o

II For asymmetrical simple pitched roofs, each side of the roof shall be treated as one half of corresponding Syttttmtrkalroofs.

76
NATIONAL BUILDING CODE OF INDIA
6.4.2.3 Simple curved roofs

THE FOLLOWING CASES 1 AND 2 MUST BE EXAMINED

Pi = 0.8
t
CASE 1

‘r!
.

P
T

L.
I

p2=o.3+loy CASE 2 P*/2 J


Restriction:
mz <2.3
m= Oi~b>60°

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 77


r-

6.4.2.4 Multi-level roofs~~

1-

.-

l==
‘r-l IJw

1-
I
-1
7
PI

p, = 0.8 with the restriction 0.8 S pWs 4.0


P~ = P,+PW where
where h is in metres
P, = due to sliding SOis in kilopascals (kilonewtons per square metre)
pW = due to wind k = 2 kNlm2 “
13 = 2h2J but is restricted as follows: f)> 15°: p,is determined from an additional load
amounting to 50 percent of the maximum total
5m<l~S15m load on the adjacent slope of the upper roof l),
and is distributed linearly as shown in the
figure.

p<15”:p,=o

!J A more extensive formula forp is described in Annex A. 1) The load on the upper roof is calculated according to 6.4.2.1
w
‘) If 1,<13,the coefficientfl is determined by interpolation between or 6.4.2.2.
,u, andp2.

78 NATIONAL BUILDING CODE OF INDIA


6.4.2.5 Complex multi-level roofs

—1, >
P

+ T hl r-
h2

7
-71 “
d-l
12+13<11

!2+[3>11

1, =24:1, =2~:p, =0.8


Restriction:

5m<12< 15rn,

5melz< 15m;

& and p, = (p, + pW), are calculated according to 6.4.2.1,6.4.2.2 and 6.4.2.4.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 79


6.4.2.6 Roofs with local projections and obstructions

rh

‘t r-r-l “

&=~
o

h = is in metres
SO= is in kilopascals (kilonewtons per square metre)
k = 2 kN/m2
p = 0.8

Restrictions:
0.8< pW 52.0
5m<l<15m

6.4.3 Shape Coef/lcients in Areas Exposed to Wind within a distance;’from the building equal to
ten times the height of the obstruction above
The shape coefficients given in 6.4.2 and Annex K
the roof level; and
may be reduced by 15 percent, provided the designer
has demonstrated that the following conditions are b) The roof does not have any significant
fulfilled: projections, such as, parapet walls which may
prevent snow from being blow off the roof.
a) The building is located in an exposed location,
such as open level terrain with only scattered NOTE — In some areas, winter climate may not be of
such a nature as to produce a significant reduction of
buildings, trees or other obstructions so that
roof loads from the snow load on the ground these areas
the roof is exposed to the winds on all sides area
and is not likely to become shielded in the @ Winter calm valleys in the mountains where
future by obstructions higher than the roof sometimes layer after layer of snow accumulates

80 NATIONAL BUILDING CODE OF INDIA


on roofs without any appreciable removal of snow element and another in buildings or
by wind and
structures, as for example, between the
b) Areas (that is, high temperature) where the
external walls and the internal elements of a
maximum snow load may be the result of single
snowstorm, occasionally without appreciable building. The distribution of temperature
wind removat. through section of single-leaf structural
elements may be assumed linear for the
In such area, the determination of the shape coefficients
purpose of analysis.
shall be based on local experience with due regard to
the likelihood of wind drifting and sliding. b) The effect of mean temperature changes t, and
tz, and the temperature gradients VIand Vzin
7 SPECIAL LOADS the hot and cold seasons for single-leaf
structural elements shall be evaluated on the
7.1 This clause gives guidance on loads and load
basis of analytical principles.
effects due to temperature changes, soil and hydrostatic
NOTES
pressures, internally generating stresses (due to creep,
shrinkage, differential settlement, etc), accidental 1 For portions of the structure below ground level, the
variation of temperature is generally insignificant.
loads, etc, to be considered in the design of buildings
However, during the period of construction, when the
as appropriate. This clause also includes guidance on portions of the structure are exposed to weather elements,
load combinations. The nature of loads to be considered adequate provision should be made to encounter adverse
for a particular situation is to be based on engineering effects, if any.
judgement (see also 3.6) 2 If it can be shown by engineering principles, or if it is
known from experience, that neglect of some or all the
7.2 Temperature Effects effects of temperature do not affect the structural safety
and serviceability, they need not be considered in design.
7.2.1 Expansion and contraction due to changes in
temperature of the materials of a structure shall be 7.3 Hydrostatic and Soil Pressure
considered in design. Provision shall be made either
7.3.1 In the design of structures of parts or structures
to relieve the stress by the provision of expansion
below ground level, such as, retaining walls and other
contraction joints in accordance with good practice
walls in basement floors, the pressure exerted by the
[6-1(10)] or design the structure to carry additional
soil or water or both shall be duly accounted for on the
stresses due to temperature effects as appropriate to
basis of established theories. Due allowance shall be
the problem.
made for possible surcharge from stationary or moving
7.2.1.1 The temperature range varies for different loads. When a portion or whole of the soil is blow the
regions and under different diurinal and seasonal free water surface, the lateral earth pressure shall be
conditions. The absolute maximum and minimum evaluated for weight of soil diminished by buoyancy
temperature which may be expected in different and the full hydrostatic pressure.
localities in Annex B of Part 6 ‘Structural Design,
7.3.1.1 All foundation slabs and other footings
Section 6 Steel’ respectively. These figures may be
subjected to water pressure shall be designed to resist
used for guidance in assessing the maximum variations
a uniformly distributed uplift equal to the full
of temperature.
hydrostatic pressure. Checking of overturning of
7.2.1.2 The temperatures indicated are the air foundation under submerged condition shall be done
temperatures in the shade. The range of variation in considering buoyant weight of foundation.
temperature of the building materials may be
7.3.2 While determining the lateral soil pressure on
appreciably greater or less than the variation of air
column like structural members, such as, pillars which
temperature and is influenced by the condition of
rest in sloping soils, the wi+th of the member shall be
exposure and the rate at which the materials composing
taken as follows (see Fig. ‘15).
the structure absorb or radiate heat. This difference in
temperature variations of the material and air should Actual Width of Member Ratio of E#ective Width
be given due consideration. to Actual Width
7.2.1.3 The structural analysis must take account of Less than 0.5 m 3.0
changes of the mean (through the section) temperature Beyond 0.5 m and up to 1 m 3.0 to 2.0
in relation to the initial (st) and the temperature gradient 2.0
Beyond 1 m
through the section.
a) It should be borne in mind that the changes The relieving pressure of soil in front of the structural
of mean temperature in relation to the initial member concerned may generally not be taken into
are liable to differ as between one structural account.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 81


n
T
n
m

L_ n
N

*a,. .,* ,

d’, “k

FIG. 15 SKETCHSHOWINGEFFECTIVEWIDTH OF PILARFORCALCULATINGSOIL PRESSURE

7.3.3 Safe-guarding of structures and structural being considered, unless otherwise specified in relevant
members against overturning and horizontal sliding codes of practice.
shall be verified. Imposed loads having favorable
Each element of the structure shall be designed for the
effect shall be disregarded for the purpose. Due
number of stress cycles of each magnitude to which it
consideration shall be given to the possibility of’ soil
is estimated that the element is liable to be subjected
being permanently or temporarily removed.
during the expected life of the structure. The number
7.4 Fatigue of cycles of each magnitude shall be estimated in the
light of available date regarding the probable frequency
7.4.1 General of occurrence of each type of loading.
Fatigue cracks are usually initiated at points of high NOTE — Apart from the general observations made herein,
stress concentration. These stress concentrations may the section is unable to provide any precise guidance in
estimating the probabilistic behaviour and response of
be caused by or associated with holes (such as, bolt or structures of various types arising out of repetitive loading
rivet holes in steel structures), welds including stray approaching fatigue conditions in structural members, joints,
or fusions in steel structures, defects in materials, and materials, etc.
local and general changes in geometry of members.
7.5 Structural Safety During Construction
The cracks usually propogate, if loading is continuous.
7.5.1 All loads required to be carried by the structures
Where there is such loading cycles, sudden changes
or any part of it due to storage or positioning of
of shape of a member or part of a member, especially
construction materials and erection equipment
in regions of tensile stress and/or local secondary
including all loads due to operation of such equipment,
bending, shall be avoided. Suitable steps shall be taken
shall be considered as erection loads. Proper provision
to avoid critical vibrations due to wind and other
shall be made, including temporary bracings, to take
causes.
care of all stresses due to erection loads. The
7.4.2 Where necessary, permissible stresses shall be conjunction with the temporary bracings shall be
reduced to allow for the effects of fatigue. Allowance capable of sustaining these erection loads, without
for fatigue shall be made for combinations of stresses exceeding the permissible stresses specified in
due to dead load and imposed load. Stresses due to respective codes of practice. Dead load, wind load and
wind and earthquakes may be ignored when fatigue is such parts of imposed load, as would be imposed on

82 NATIONAL BUILDING CODE OF INDIA


the structure during the period of erection, shall be The codal requirements regarding impact from vehicles
taken as acting together with erection loads. and cranes are given in 7.6.1.2 and 7.6.1.3.

7.6 Accidental Loads 7.6.1.2 Collisions between vehicles and structural


The occurrence of which, with a significant value, is elements
unlikely on a given structure over the period of time In road traffic, the requirement that a structure shall
under consideration, and also inmost cases, is of short be able to resist collision maybe assumed to be fulfilled
duration. The occurrence of an accidental load could, in if it is demonstrated that the structural element is able
many cases, be expected to cause severe consequences, to stop a fictitious vehicle, as described below. It is
unless special measures are taken. assumed that the vehicle strikes the structural element
The accidental loads arising out of human action at a height of 1.2 m in any possible direction and at a
include the following: speed of 10 rrsls (36 km/h).

a) Impacts and collisions, The fictitious vehicle shall be considered to consist of


b) Explosions, and two masses ml and mz which during compression of
the vehicle, produce an impact force increasing
c) Fire.
uniformly from zero, corresponding to the
Characteristic of the above stated loads are that they rigidities c1 and C2. It is assumed that the mass ml is
are not a consequence of normal use and that they are broken completely before the breaking of mass mz
undesired, and that extensive effects are made to avoid begins.
them. As a result, the probability of occurrence of an
accidental load is small whereas the consequences may The following numerical values should be used:
be severe. ml = 400 kg, Cl = 10000 kN/m, the vehicle is
The causes of accidental loads may be: compressed.
=12000 kg, C2= 300 kN/m, the vehicle is
a) inadequate safety of equipment (due to poor m2
compressed.
design or poor maintenance); and
NOTE — The described fictitious collision corresponds in
b) wrong operation (due to insufficient teaching
the case of a non-elastic strncturat element to a maximum static
or training, indisposition, negligence or force of 630 kN for the mass ml and 600 kN for the mass m2
unfavorable external circumstances). irrespective of the elasticity, it will therefore be on the safe
side to assume the static force to be 630 kN.
In most cases, accidental loads only develop under a
combination of several unfavorable In
occurrence. In addition, breaking of the mass ml will result in art
practical applications, it maybe necessary to neglect impact wave, the effect of which will depend, to a great
the most unlikely loads. The probability of occurrence extent, on the kind of structural element concerned.
of accidental loads, which are neglected, may differ Consequently, it will not always be sufficient to design
for different consequences of a possible failure. A data for the static force.
base for a detailed calculation of the probability will
seldom be available. 7.6.1.3 Safety railings

7.6.1 Impact and Collisions With regard to safety, railings put up to protect
structures against collision due to road traffic, it should
7.6.1.1 General
be shown that the railings are able to resist the impact
During an impact, the kinetic impact energy has to be as described in 7.6.1.2.
absorbed by the vehicle hitting the structure and by
NOTE — When a vehicle collides with safety railings, the
the structure itself. In an accurate analysis, the kinetic energy of the vehicle will be absorbed partly by the
probability of occurrence of an impact with a certain deformation of the railings and partly by the deformation of
energy object hitting the structure and the structure the vehicle. The part of the kinetic energy which the railings
itself at the actual place must be considered. Impact should be able to absorb without breaking down may be
determined on the basis of the assumed rigidity of the vehicle
energies for dropped object should be based on the
during compression.
actual loading capacity and lifting height.

Common sources of impact are: 7.6.1.4 Crane impact load on buffer stop

a) Vehicles; The basic horizontal load PY (tones), acting along the


crane track produced by impact of the crane on the
b) Dropped objects from cranes, fork lifts, etc;
buffer stop, is calculated by the following formula:
c) Cranes out of control, crane failures; and
d) Flying fragments. Py = Mvlf

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 83


where the concentration of the explosion, the shape of the room,
possibilities of ventilation of the explosion, and the ductifity
v= Speed at which the crane is traveling at the and dynamic properties of the structure. In rooms with little
moment of impact (assumed equal to half possibility for relief of the pressure from the explosion, very
the nominal value) (m/s). large pressures may occur.
Internal over pressure from an internal gas explosion in rooms
f. Maximum shortening of the buffer, assumed of sizes comparable to residential rooms and with ventilation
equal to 0.1 m for light duty, medium-duty areas consisting of window glass breaking at a pressure of
and heavy-duty cranes with flexible load 4 kN/m2(3-4 mm machine made glass) maybe calculated from
suspension and loading capacity not the following method:
exceeding 50 t, and 0.2 m in every other a) The over pressure is assumed to depend on a factor
A/V, where A is the total windows area in mz and V is
cranes. the volume in m3 of the room considered;
M= Reduced crane mass, (t. s2/m); and is b) The internal pressure is assumed to act simultaneously
obtained by the formula: upon all walls and floors in one closed room, and
c) The action qO may be taken as static action.
If account is taken of the time curve of the action, the
schematic correspondence between pressure and time is
assumed (Fig. 16), where tl is the time from the start of
where combustion until maximum pressure is reached and tz is the
g = Acceleration due to gravity (9.81 m/s2); time from maximum pressure to the end of combustion. For
t, and t2, the most unfavorable valnes should be chosen in
P, = Crane bridge weight (t); relation to the dynamic properties of the structures. However,
P, = Crab bridge weight (t); the values should be chosen within the intervals as given in
Fig. 17. .
Q = Crane loading capacity (t); .,--
2 Figure 16 is based on tests with gas explosions in room
k = Coefficient, assumed equal to zero for corresponding to ordinary residential flats and should,
cranes with flexible load suspension and to therefore, not be applied to considerably different conditions.
The figure corresponds to an explosion caused by town gas
one for cranes with rigid suspension; and it might, therefore, be somewhat on the safe side in rooms
L, = Crane span (m); and where there is only the possibility of gases with a lower rate of
combustion.
1 = Nearness of crab (m).
The pressure may be applied solely in one room or in more
7.6.2 Explosions rooms at the same time. In the latter case, all rooms are
incorporated in the volume V. Only windows or other similarly
7.6.2.1 General weak and light weight structural elements may be taken to be
ventilation areas even though certain limited stmcturaf parts
Explosions may cause impulsive loading on a structure. break at pressures less than qO.
The following types of explosions are particularly Figure 16 is given purely as guide and probability of occurrence
relevant: of an explosion should be checked in each case using
appropriate values.
a) Internal gas explosions which may be caused
by leakage of gas piping (including piping 7.6.3 Vertical Load on Air Raid Shelters
outside the room), evaporation from volatile 7.6.3.1 Characteristic values
liquids or unintentional evaporation from
surface material (for example, fire); As regards buildings in which the individual floors are
b) Internal dust explosions; acted upon by a total characteristic imposed action of
c) Boiler failure; up to 5.0 kN/m2, vertical actions on air raid shelters
generally located below ground level, for example,
d) External gas cloud explosions; and
basement, etc, should be considered to have the
e) External explosions of high explosives (TNT,
following characteristic values:
dynamite).
The codal requirement regarding internal gas Buildings up to 2 storeys 28 kNlm2
explosions is given in 7.6.2.2. Buildings with 3-4 storeys 34 kNlm2

7.6.2.2 Explosion effect in closed rooms Buildings with more than 4 storeys 41 kN/m2
Buildings of particularly stable construction 28 kN/m2
Gas explosion may be caused, for example by leaks in
irrespective of the number of storeys
gas pipes (inclusive of pipes outside for room),
evaporation from volatile liquids or unintentional
In the case of buildings with floors that are acted upon
evaporation of gas from wall sheathings (for example,
by a characteristic imposed action larger than
caused by fire).
5.0 kN/m2, the above values should be increased by
NOTES the difference between the average imposed action on
1 The effect of explosions depends on the exploding medium, all storeys above the one concerned and 5.0 kN/m2.

84 NATIONAL BUILDING CODE OF INDIA


kN {m2
t
90 b

80

70 ~

60

50

40 ,

30

20 k

10 ,
A -1
iim.
30

FIG. 16 SKETCHSHOWINGRELATIONBETWEENPRESSUREANDTIME

. ———. —

1- t,#- ,2 -1 TIME(s,

FIG. 17 SKETCHSHOWINGTIME INTERVALANDPRESSURE

NOTES a) the time-temperature curve and the required


1 By storeys it is understood, every utilizable storey above the fire resistance (minutes), and
shelter.
b) an energy balance method.
2 By buildings of a particular stable construction, it is
understood, buildings in which the load-bearing structures are If the thermal effect during fire is determined from an
made from reinforced in-situ concrete.
energy balance method, the fire load is taken to be:
7.6.4 Fire
q=12tb
7.6.4.1General
where
Possible extraordinary loads during a fire may be
q = Fire action (kJ per m2 floor), and
considered as accidental actions. Examples are loads
from people along escape routes and loads on another tb= Required fire resistance (minutes) [see
structure from structure failing because of a fire. 6-1(11)].
NOTE — The fire action is defined as the total quantity of
7.6.4.2Thermal efects duringjire heat produced by complete combustion of all combustible
material in the fire compartment, inclusive of stored goods
The thermal effect during fire may be determined from and equipment together with building structures and building
one of the following methods: materials.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 85


7.7 Vibrations (DL = dead load, IL= imposed load, WL = wind
load, EL= earthquake load and TL = temperature
For general details on loads due to vibrations, reference
load).
may be made to Annex L.
NOTES
7.8 Other Loads 1 When snow load is present on roof’s, replace imposed load
by snow load for the purpose of above load combinations.
Other loads not included in the Section, such as special
2 The relevant design codes shatl be followed for permissible
loads due to technical process, moisture and shrinkage
stresses when the structure is designed by working stress
effects, etc, should be taken into account where method and for partiat safety factors when the structure is
stipulated by building design codes or established in designed by limit stale design method for each of the above
accordance with the performance requirement of the load combinations.
structure. 3 Whenever imposed load (IL) is combined with earthquake
load (EL), the appropriate part of imposed load as specified
7.9 For additional information regarding loads, forces in 5 shoutd be used, both for evaluating earthquake effect and
and effects about cyclone resistant buildings and atso for combined bad effects used in such combination.
4 For the purpose of stabitity of the structure as a whole against
landslide control aspects, reference may be made to
overturning, the restoring moment shall be not less than 1.2
good practices [6- 1(12)] and 6-1 (13)] respectively. times the maximum overhnning moment due to dead load plus
1.4 times the maximum overturning moment due to imposed
8 LOAD COMBINATIONS loads. In cases where dead load provides the restoring moment,
only 0.9 times the dead load shall be considered. The restoring
8.1 General moments due to imposed loads shatl be ignored.
5 The structure shall have a factor against skiing of not less
A judicious combination of the loads keeping in view ---
than 1.4 under the most adverse combhation of the applied
the probability of loads/forces. In this case, only 0.9 times the dead load shatl be
taken into account.
a) their acting together; and
6 Where the bearing pressure on soil due to wind alone is less
b) their disposition in relation to other loads and than 25 percent of that due to dead load and imposed load, it
severity of stresses or deformations caused may be neglected in design where this exceeds 25 percent,
by the combinations of the various loads, is foundation may be so proportioned that the pressure due to
combined effect of dead load, imposed load and wind load does
necessary to ensure the required safety and not exceed the allowable bearing pressure by more than 25
economy in the design of a structure. percent. When earthquake effect is included, the permissible
increase in atlowable bearing pressure in the soil shall be in
8.2 Land Combinations accordance with 5.
Keeping the aspect specified in 8.1, the various loads Reduced imposed load specified in 3 for the design of
supporting structures should not be applied in combination
should, therefore, be combined in accordance with the with earthquake forces.
stipu:~ation in the relevant design codes. In the absence 7 Other loads and accidental load combination not included
of such recommendations, the following loading should be dealt with appropriately.
combinations, whichever combination produces the 8 Crane load combinations are covered in 3.6.4.
most unfavorable effect in the building, foundation
or structural member concerned may be adopted (as a 9 MULTI-HAZARD RISK IN VARIOUS
general guidance). It should also be recognized in load DISTRICTS OF INDIA
combinations that the simultaneous occurrence of 9.1 Multi-Hazard Risk Concept
maximum values of wind, earthquake, imposed and
The commonly encountered hazards are:
snow loads is not likely.
a) earthquake,
1) DL
b) cyclone,
2) DL + IL
c) wind storm,
3) DL + WL
d) floods,
4) DL + EL
e) landslides,
5) DL -t TL
f) liquefaction of soils,
6) DL+IL+WL extreme winds,
g)
7) DL+IL+EL h) cloud bursts, and
8) DL+IL+TL failure of slopes.
0
9) DL+WL+TL
A study of the earthquake, windfcyclone, and flood
10) DL+EL+ TL
hazard maps of India indicate that there are several
11) DL+IL+ WL+TL areas in the country which run the risk of being affected
12) DL + IL i- EL+TL by more than one of these hazards.

86 NATIONAL BUILDING CODE OF INDIA


Further there may be instances where one hazard may a) Earthquake and Flood Risk Prone — I)isticts
cause occurrence or accentuation of another hazard, which have seismic Zone of intensity 7 or
such as landslides may be triggered/accelerated by more and also flood prone unprotected or
earthquakes and wind storms and floods by the protected area. Earthquake and flood can
cyclones. occur separately or simultaneously.

It is important to study and examine the possibility of b) Cyclone and Flood Risk Prone — Districts
which have cyclone and flood prone areas.
occurrence of multiple hazards, as applicable to an area.
Here floods can occur separately from
However, it is not economically viable to design all
cyclones, but simultaneous also along with
the structures for multiple hazards. The special
possibility of storm surge too.
structures, such as, nuclear power plants, and life line
structures, such as, hospitals and emergency rescue c) Earthquake, Cyclone and Flood Risk Prone
shelters may be designed for multiple hazards. For such — Districts which have earthquake Zone of
special structures, site specific data have to be collected intensity 7 or more, cyclone prone as well as
and the design be carried out based on the accepted flood prone (protected or unprotected) areas.
levels of risk. The factors that have to be considered Here the three hazards can occur separately
and also simultaneously as in (a) and(b) above
in determining this risk are:
but earthquake and cyclone will be assumed
a) The severity of the hazard characterized by to occur separately only.
M.M. (or M. S. K.) intensity in the case of d) Earthquake and Cyclone Risk Prone —
earthquake; the duration and velocity of wind Districts which have earthquake zone of
in the storms; and unprotected or protected intensity 7 or more and pro-ne to cyclone
situation of flood prone areas; and hazard too. The two wiii be assumed to occur
b) The frequent y of occurrence of the severe separately.
hazards.
Based on the approach given above, the districts with
Till such time that risk evaluation procedures are multi-hazard risk are given in Annex M.
formalized, the special structures may be designed for
multiple hazards using the historical data, that can be 9.3 Use of the List of the District with Multi-hazard
obtained for a given site and the available Code for Risk
loads already covered. The designer may have to The list provides some ready information for use of
consider the loads due to any one of the hazards the authorities involved in the task of disaster
individually or in combination as appropriate. mitigation, preparedness and preventive action. This
information gives the district which are prone to high
9.2 Multi-Hazard Prone Areas
risk for more than one hazard. This information will
The criteria adopted for identifying multi hazard prone be useful in establishing the need for developing
areas may be as follows: housing design to resist the such multi-hazard situation.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 87


ANNEX A
[Clause 3.3.2 .l(b)]
ILLUSTRATIVE EXAMPLE SHOWING REDUCTION OF UNIFORMLY DISTRIBUTED
IIMPOSED FLOOR LOADS IN MULTI-STOREYED BUILDINGS
FOR DESIGN OF COLUMNS

A-1 The total imposed loads from different floor levels floor levels using 3.3.2.1. Floor loads do not exceed
(including the roof) combing on the central column of 5.0 kN/m2.
a rnulti-storeyed building (with mixed occupancy) is A-1.l Applying reduction coefficients in accordance
shown in Fig. 20. Calculate the reduced imposed with 3.3.2.1, total reduced floor loads on the column
load for the design of column members at different at different levels is indicated along with Fig. 18.

FLOOR No. ACTUAL FLOOR


FROM TOP LOAD COMING
INCLUDING ON DIFFERENT
ROOF FLOORS )(N
4 LOADS FOR WHICH COLUMNS ARE TO BE DESIGNED
kN

11130 1
I
ROOF

I
2 40 30

(30+40)(1-0.1)=63

4 50 (30+40 + 50)(1 -0.2)=96


I
i
5 40 (30+40+50+50)(1-0.3)=119

6 45 (30+40+50+50+40)(1 -0.4)= 126


●

7 50 (30+40 +50+50+40+45)(1-0.4)=153
I
8 50 ‘30+40 +50+50
L +40+45 +50)( 1- O.4)= 183

9 “ 40 (30+40 +50+50 +40+45 +50+50) (1-0.4)


=213

(30+40 +50+50+40+45+50+50+40)
10 40
(1 -0.4)= 237

(30+40 +50+50+40+45+50+50+40+40)
11 40
r i
1 (1-0.4)= 261
(30+40 +50+50+40+45+50+50+40+404

II 12 55 + 40) (1-0.5)= 237.5 c 261


adopt 261 for design
(30+40 +50+50+40+45+50+50+40+40
13 55
+40 + 55) (1-0.5)= 265 “
*
(30+40 +50+50+40+45+50+50+40+40
A4 70
+40 + 55 + 55)(1 -0.5)= 292.5

(30+40 +50+50+40+45+50+50+40+40
15 80
+40 + 55 + 55 + 70) (1-0.5)= 327.5

/
lt---’--
(30+40 +50+50+40+45+50+50+40+40
+40 + 55 + 55+ 70 + 80) (1-0.5)= 367.5 I
FIG. 18

88 NATIONAL BUILDING CODE OF INDIA


ANNEX B

(Clause 4.2)

NOTATIONS

A= Surface area of a structure or part of a structure K= Multiplication factor


A, = Effective frontal area 1= Length of the member or greater horizontal
A, = An area at height Z dimension of a building
b= Breadth of a structure or structural member pd = Design wind pressure
normal to be wind stream in the horizontal Pz = Design wind pressure at height Z
plane Pe = External pressure
Cf = Force coefficient/drag coefficient pi = Internal pressure
Cfn = Normal force coefficient Rc = Reynolds number
c,, = Transverse force coefficient s= Strouhal number
c;. = Frictional drag coefficient v, = Regional basic wind speed
c, = Pressure coefficient
<= Mean hourly wind speed corresponding to
Cpe= External pressure coefficient
10 m height
c,, = Internal pressure coefficient
Vz = Design wind velocity at height Z
d= Depth of a structure or structural member
parallel to wind stream ~= Hourly mean wind speed at height Z
D= Diameter of cylinder w= Lesser horizontal dimension of a building
F= Force normal to the surface or a structural member
F. = Normal force w’. Bay within multi-bay buildings
F, = Transverse force x = Distance down wind from a change in terrain
F = Frictional force category
h = Height of structure above mean ground level e= Wind angle from a given axis
hX = The height of development of a velocity a. Inclination of the roof to the horizontal
profile at a distance x down wind from a
0= Solidity ratio
change in terrain category
z= A height or distance above the ground
E= Average height of the surface roughness
k2 }= Multiplication factors

ANNEX C

(Clause 4.4.2)

BASIC WIND SPEED A 10 m HEIGHT FOR SOME IMPORTANT CITIES/TOWNS

City/Town Basic Wind Speed City/Town Basic Wind Speed


ds mls
Agra 47 Barauni 47
Ahmedabad 39 Bareilly 47
Ajmer 47 Bhatinda 47
Almora 47 Bhilai 39
Amritsar 47 Bhopal 39
Asansol 47 Bhubaneshwar 50
Aurangabad 39 Bhuj 50
Bahraich 47 Bikaner 47
Bangalore 33 Bokaro 47

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 89


City/Town Basic Wind Speed City/Town Basic Wind Speed
rnfs In/s
Calicut 39 Mangalore 39
Chandigarh 47 Moradabad 47
Chennai 50 Mumbai 44
Coimbatore 39 Mysore 33
Cuttack 50 Nagpur 44
Darbhanga 55 Nainital 47
Dmjeeling 47
Nasik 39
Debra Dun 47
Nellore 50
Delhi 47
Panjim 39
Durgapur 47
Patiala 47
Gangtok 47
Patna 47
Guwahati 50
Pondichen-y 50
Gaya 39
Portblair 44
Gorakhpur 47
Pune 39
Hyderabad 44
Raipur 39
Imphal 47
Jabalpur Rajkot 39
47
Jaipur Ranchi 39
47
Jamshedpur 47 Roorkee 39
Jhansi 47 Rourkela 39
Jodhpur 47 Shimla 39
Kanpur 47 Srinagar 39
Kohima 44 Surat 44
Kolkata 50 Tiruchchirappalli 4’7
Kurnool 39 Thiruvananthpuram 39
Lakshadweep 39 Udaipur 47
Lucknow 47 Vadodara 44
Ludhiana 47 Varanasi 47
Madurai 39 Vijayawada 50
Mandi 39 Vishakhapatnam 50

ANNEX D

[Clause 4.4.3.2(d)]

CHANGES IN TERRAIN CATEGORIES

D-1 LOW TO HIGH NUMBER determined in relation to the less rough (more
D-1.l In cases of transitions from a low category distant) terrain.
number (corresponding to a low terrain roughness) to
D-2 HIGH TO LOW NUMBER
a high category number (corresponding to a rougher
terrain), the velocity profile over the rougher terrain D-2.1 In cases of transitions from a more rough to a
shall be determined as follows: less rough terrain, the velocity profile shall be
determined as follows:
a) Below height hX, the velocities shall be
determined in relation to the rougher terrain; a) Above height hX, the velocities shall be
and determined in accordance with the rougher
b) Above height hX, the velocities shall be (more distant) terrain; and

90 NATIONAL BUILDING CODE OF INDIA


b) Below height hx, thevelocities shall be taken profiles in the vicinity of a change in terrain category
areshown in Fig. land.
as the lesser of the following:
D-3 MORE THAN ONE CATEGORY
1) that determined in accordance with the
less rough terrain; and D-3.1 Terrain changes involving more than one
2) thevelocity atheighth .x. asdeterminedin category shall be treated in similar fashion to that
relation to the rougher terrain. described in A-1 and A-2.
NOTE — Examples of the determination of velocity NOTE — Examples involving three terrain categories are
shown in Fig. 19(c).

WIND DIRECTION

CATEGORY 2

L-X44’ ‘ATE’”””

xd=FETCH, hd= HEIGHT FOR CATEGORY 4

0****.***9.** 0-.09.00
●
PROFILE FOR CATEGORY 4

.- —- —--- . PROFILE FOR CATEGORY 2

DESIGN. PROFILE AT A

a) DETERMINATION OF VELOCITY PROFILE NEAR A CHANGE IN TERRAIN CATEGORY


(Less rough to more rough)

xq=FETCH, hd= HEIGHT FOR CATEGORY 2

- ....***.*-* -*.99-***- PROFILE FOR CATEGORY 4


/
.—— —————- PROFILE FOR CATEGORY 2
0
0
0
DESIGN PROFILE AT A /
0
/ hz
●*: /
WIND DIRECTION /’ ●’
~ ●*
/ ●’
1

CATEGORY 4 CATEGORY 2 !’

b) DETERMINATION OF VELOCITY PROFILE NEAR A CHANGE IN TERRAIN CATEGOR


(More rough to less rough)

FIG. 19 VELOCITY PROFILESIN THE VICINITY OF A CHANGE IN TERRAINCATEGORY — Continued

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 91


hd X4
xd=FETCH, hA= HEIGHT FOR CATEGORY 4
0
xl= FETCH, hl= HEIGHT FOR CATEGORY 1 I \+x hd
.%

A B
CATEGORY 3 CATEGORY 1 CATEGORY 4

t--x’ t--x’
9
●
9

●’
“ //
●
●
● I
hl

VELOCITY VELOCITY

VELOCITYPROFILE FORCATEGORY4
VELOCITYPROFILE FORCATEGORY3
VELOCITY PROFILE FORCATEGORY 1 .
DESIGNP~OFILE

c)DETERMINATION OFDESIGNPROFILE INVOLVING MORE THANONECHANGE


TERRAIN CATEGORY

FIG. 19 VELOCITYPROFILESINTHEVICINITYOFACHANGE IN TERRAINCATEGORY

ANNEX E
(Clause 4.4.3.3)
EFFECT OF A CLIFF OR ESCARPMENT ON THE EQUIVALENT HEIGHT
ABOVE GROUND (k3 FACTOR)

E-1 The influence of the topographic feature is b


T

considered to extend 1.5 L~ is the effective horizontal >17°


0.3
length of the hill depending on slope as indicated below
(see Fig. 20). where L is the actual length of the upwind slope in the
wind direction, Z is the effective height of the feature,
Slope L and 0 is the upwind slope in the wind direction.
3°<(3 —
<17” L’ If the zone downwind from the crest of the feature is

g~
NATIONAL BUILDING CODE OF INDIA
relatively flat, (El < 3°) for a distance exceeding L~, Slope c
then the feature should be treated as an escarpment. If
not then the feature should be treated as a hill or ridge.
Examples of typical features are given in Fig. 20.
NOTES
3°<0<

>17°
170 1.2 ;

0.36
()
1 No difference is made in evaluating k~ between a three
s is a factor derived in accordance with E-2.l
dimensional hill and two dimensional ridge.
2 In undulating terrain, it is often not possible to decide whether
appropriate to the height, H above mean ground level
the local topography to the site is significant in terms of wind and the distance x from the summit or crest, relative to
flow. In such cases, the average value of the terrain upwind of the effective length, Le.
the site for a distance of 5 km should be taken as the base level
from wind to assess the height L.and the upwind slope (3of the E-2.1 The factors should be determined from:
feature.
a) Figure 21 for cliffs and escarpments, and
E-2 TOPOGRAPHY FACTOR, lq b) Figure 22 for hills and ridges.
NOTE — Where the downwind slope of a hill or ridge is
The topography factor k~ is given by the following:
greater than 3“, there will be large regions of reduced
k3=l+cs accelerations or even shelter and it is not possible to give
general design rules to cater for these circumstances. Values
where C has the following values: ofs from Fig. 22 may be used as upper bound values

REGION AFFECTED BY
TOPOGRAPHICAL FEATURE CREST —

WIND t-’”5L:~2”5Le—
I I

AVERAGE GROUND
LEVEL
[

-ve UPWIND +Ve DOWNWIND

20 (a) GENERAL NOTATIONS

/“
,CREST
DOWNWIND SLOPE > 3“
WIND DOWNWIND SLOPE <3° WIND

+ +

20 (b) CLIFF AND ESCARPMENT 20 (c) HILL AND RIDGE

FIG. 20 DEFINITIONOF TOPOGRAPHICALDIMENSIONS

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 93


CREST CREST

2.0 2.0

I
1.5 r \ 1.5

$$
0 I 1
1.0 1.0 :
1/ !
e

0.5 0.5
\

0 0
-1.5 -1.0 -0.5 01”00 0.5 1.0 1.5 2.0 2.5
.x_
DOWNWIND &
‘w’ND Le
FIG. 21 FACTORs FOR CLIFF AND ESCARPMENT r

.,-
CREST CREST

2.0 ‘ I 2.0

A
1.5 \ 1,5
\
@
Q \
1.0 — ~ 1.0
. 0,2
@
0.4
0.5 ‘ 0.5

o’ 0
-1.5 -1.0 -0.5 01”00 0.5 1.0 1.5 2.0 2.5
x &
‘PW’ND G ‘OwwND Le

FIG. 22 FACTOR SFORRIDGE AND HILL

ANNEX F ,

[Clau~e 4.5.3.2 (b)]

WIND FORCE ON CIRCULAR SECTIONS

F-1 The wind force on any object is given by: p~ = Design pressure of the wind.

F= C~ A,. pd For most shapes, the force coefficient remains


approximately constant over the whole range of wind
where
speeds likely to be encountered. However, for objects
C~=Force coefficient, of circular cross-section, it varies considerably.
A,= Effective area of the object normal to the wind For a circular section, the force coefficient depinds
direction, and upon the way in which the wind flows around it and is

94 NATIONAL BUILDING CODE OF INDIA


dependent upon the velocity and kinematic viscosity subjected to wind having an intensity and scale of
of the wind and diameter of the section. The force turbulence typical of built-up urban areas. The curve
coefficient is usually quoted against a non-dimensional for a smooth cylinder e/D = 1 x 10_5 in a steady air-
parameter, called the Reynolds number, which takes stream, as found in a low-turbulence wind tunnel is
account of the velocity and viscosity of the flowing shown for comparison.
medium (in the case the wind) and the member
It can be seen that the main effect of free-stream
diameter.
turbulence is to decrease the critical value of the
parameter DV~. For subcritical flows, turbulence can
m,
Reynolds number, R. = — produce a considerable reduction in C~below the steady
Y air-stream values. For super-critical flows, this effect
becomes significantly smaller.
where
If the surface of the cylinder is deliberately roughened,
D = Diameter of the membe~
such as by incorporating flutes, riveted construction,
V, = Design wind speed; and etc then the data given in Fig. 5 for appropriate value
y = Kinematic viscosity of the air which is of EID >0 shall be used.
1.46 x 105 m2/s at 15°C and standard
NOTE — In case of uncertainty regarding the value of &to be
atmospheric pressure. used for smalI roughness, tiD shall be taken as 0.001.
Since in most natural environments likely to be found
in India, the kinematic viscosity of the air is fairly
constant, it is convenient to use DVd as the parameter
instead of Reynolds numbers and this has been done
in this Section.

The dependence of a circular section’s force coefficient


or Reynolds number is due to the change in the wake
developed behind the body.

At a low Reynolds number, the wake is as shown in


Fig. 23 and the force coefficient is typically 1,2. As ‘ FIG. 23 WA= IN SUBWTICAL FLOW
the Reynolds number is increased, the wake gradually
changes to that shown in Fig. 24, that is, the wake width
dW decreases and the separation point, S moves from
the front to the back of the body.

As a result, the force coefficient shows a rapid drop at w


a critical value of Reynolds number, followed by a
gradual rise and Reynolds number is increased still ‘-~
further.

The variation of C~ with parameter DV~ is shown in s

Fig. 5 for infinitely long circular cylinders having


various values of relative surface roughness EJD when FIG. 24 WAKE ‘IN SUPER-CRITICALFLOW

ANNEX G

(Clause 5.0)

SYMBOLS

The symbols and notations given below apply to the b, ith Floor plan dimension of the building
provisions of this Code: perpendicular to the direction of force
c Index for the closely-spaced
A, Design horizontal seismic coefficient
d Base dimension of the building, in metres,
A, Design horizontal acceleration spectrum
in the direction in which the seismic force
value for mode k of vibration
is considered.

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 95


DL Response quantity due to dead load T Undamped natural period of vibration of the
e~i Static eccentricity to be used at floor i structure (in second)
calculated as per 5.4.8.2. T= Approximate fundamental period (in
e.s, Static eccentricity at floor i defined as the second)
distance between centre of mass and centre T, Fundamental natural period of vibration (in
of rigidity second)
ELX Response quantity due to earthquake load T, Undamped natural period of mode k of
for horizontal shaking along x-direction vibration (in second)
EL Response quantity due to earthquake load v, Design seismic base shear
Y
for horizontal shaking along y-direction
VB Design base shear calculated using the
ELZ Response quantity due to earthquake load approximate fundamental period T.
for vertical shaking along z-direction
vi Peak storey shear force in storey i due to all
F rcof Design lateral forces at the roof due to all modes considered
modes considered
vi, Shear force in storey i in mode k
Fi Design lateral forces at the floor i due to all
v rmf Peak storey shear force at the roof due to all
modes considered
modes considered
g Acceleration due to gravity
w Seismic weight of the structure
h Height of structure, in metres
w, Seismic weight of floor i
h, Height measured from the base of the
building to floor i z Zone factor
I Importance factor O,, Mode shape coefficient at floor i in mode k
IL Response quantity due to imposed load A Peak response (for example, member forces,
M, displacements, storey forces, storey shears or
Modal mass of mode k
base reactions) due to all modes considered
n number of storeys
A, Absolute value of maximum response in
N SPT value for soil
mode k
P, Modal ptiicipation factor of mode k
A= Absolute value of maximum response in
Q, Lateral force at floor i mode c, where mode c is a closely-spaced
Q,, Design lateral force at floor i in mode k mode
r Number of modes to be considered as A“ Peak response due to the closely-spaced
per 5.4.8.4.2 modes only
R Response reduction factor P. Coefficient used in the Complete Quadratic
IJ
s~g Average response acceleration coefficient Combination (CQC) method while combining
for rock or soil sites as given by Fig. 2 and responses of modes i and j
Table 3 based on appropriate natural periods (f)i Circular frequency in rad/second in the ith
and damping of the structure mode

ANNEX H

(Clause 5.1.15)

COMPREHENSIVE INTENSITY SCALE (MSK 64)

The scale was discussed generally at the inter- Type A — Building in field-stone, rural
governmental meeting convened by UNESCO in April structures, unburnt-brick houses,
1964. Though not finally approved the scale is more clay houses.
comprehensive and describes the intensity of Type B — &iinary brick buildings, buildings
earthquake more precisely. The main definitions used
of large block and prefabricated
are followings: type, half timbered structures,
a) Type of Structures (Buildings) buildings in natural hewn stone.

96 NATIONAL BUILDING CODE OF INDIA


Type C — Reinforced buildings, well built to shake. Hanging objects swing slightly.
wooden structures. Liquid in open vessels are slightly
b) Definition of Quanti~: disturbed. In standing motor cars the
shock is noticeable.
Single, few About 5 percent
5. Awakening
Many About 50 percent
i) The earthquake is felt indoors by all
Most About 75 percent
outdoors by many. Many people
c) Classification of Damage to Buildings awake. A few run outdoors uneasy.
Grade 1 Slight Fine cracks in Building tremble throughout.
damage plaster: fall of small Hanging objects swing considerably.
pieces of plaster Pictures knock against walls or
swing out of place. Occasionally
Grade 2 Moderate Small cracks in
pendulum clocks stop. Unstable
damage plaster: fall of fairly
objects overturn or shift. Open doors
large pieces of
and windows are thrust open and
plaster; pantiles slip
oft slam back again. Liquids spill in
cracks in
chimneys parts of small amounts from well-filled open
chimneys fall down containers. The sensation of
vibration is like that due to heavy
Grade 3 Heavy Large and deep
damage cracks in plaster: objects falling inside the buildings.
fall of chimneys ii) Slight damages in buildings of Type
Grade 4 Destruction Gaps in walls: parts A are possible.
of buildings may iii) Sometimes changes inflow-of springs.
collapse; separate 6. Frightening
parts of the
i) Felt by most indoors and outdoors.
buildings lose their
Many people in buildings are
cohension; and
frightened and run outdoors. A
inner walls collapse
few persons loose their balance.
Grade 5 Total Total collapse of the
Domestic animals run out of their
damage buildings
stalls in few instances, dishes and
d) Intensity Scale glassware may break and books fall
1. Not noticeable — The intensity of the down. Heavy furniture may possibly
vibration is below the limits of move and small steeple bells may
sensibility y; the tremor is detected and ring.
recorded by seismograph only. ii) Darnage of Grade 1 is sustained in
2. Scarcely noticeable (very slight) — single buildings of Type B and in
Vibration is felt only by individual people many of Type A, Damage in few
at rest in houses, especially on upper buildings of Type A is of Grade 2.
floors of buildings. iii) In few cases, cracks up to widths of
3. Weak, partially observed only — The 1 cm possible in wet ground; in
earthquake is felt indoors by a few mountains occasional landslips;
people, outdoors only in favorable change inflow of springs and in level
circumstances. The vibration is like that of well water are observed.
due to the passing of a light truck. 7. Damuge of buildings
Attentive observers notice a slight i) Most people are frightened and run
swinging of hanging objects, somewhat outdoors. Many find it difficult to
more heavily on upper floors. stand. The vibration is noticed by
4. Largely observed — The earthquake is persons driving motor cars. Large
felt indoors by many people, outdoors by bells ring.
few. Here and there people awake, but ii) In many buildings of Type C damage
no one is frightened. The vibration is like of Grade 1 is caused; in many
that due to the passing of a heavily loaded buildings of Type B damage is of
truck. Windows, doors, and dishes rattle. Grade 2. Most buildings of Type A
Floors and walls crack. Furniture begins suffer damage of Grade 3, few of

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 97


!
Grade 4. In single instances, slopes and river banks more than
landslides of roadway on steep slopes; 10 cm. Furthermore a large number
crack in roads; seams of pipelines of slight cracks in ground; falls of
damaged; cracks in stone walls. rock, many land slides and earth
iii) Waves are formed on water, and is flows; large waves in wate. Dry
made turbid by mud stirred up. wells renew their flow and existing
Water levels in wells change, and the wells dry up.
flow of springs changes. Sometimes 10. General destruction of buildings
dry springs have their flow resorted i) Many buildings of Type C suffer
and existing springs stop flowing. In damage of Grade 4, and few of
isolated instances parts of sand and Grade 5. Many buildings of Type B
gravelly banks slip off. show a damage of Grade 5. Most of
8. Destruction of buildings Type A have destruction of Grade 5.
i) Fright and panic; also persons Critical damage of dykes and dams.
driving motor cars are disturbed. Severe damage to bridges. Railways
Here and there branches of trees lines are bent slightly. Underground
break off. Even heavy furniture pipes are bent on broken. Road
moves and partly overturns. Hanging paving and asphalt show waves.
lamps are damaged in part. ii) In ground, cracks up to widths of
ii) Most buildings of Type C suffer several centimetres, sometimes up to
damage of Grade 2, and few of Grade 1 m. Parallel to water courses occur
3. Most buildings of Type B suffer broad fissures. Loose ground slides
damage of Grade 3. Most buildings from steep slopes. From river banks
of Type A suffer damage of Grade 4. and steep coasts considerable
Occasional breaking of pipe seams. landslides are possible. In coastal
Memorials and monuments move and areas displacement of sand and mud;
twist. Tombstones overturn. Stone change of water level in wells; water
walls collapse. from canals; lakes; rivers; etc,
iii) Small landslips in hollows and on thrown on land. New lakes occur.
banked roads on steep slopes; cracks 11. Destruction
in ground up to widths of several i) Severe damage even to well built
centimeters. Water in lakes become buildings, bridges, water damps and
turbid. New reservoirs come into railway lines. Highways become
existence. Dry wells refill and useless. Underground pipes destroyed.
existing wells become dry. In many ii) Ground considerably distorted by
cases, change in flow and level of
broad cracks and fissures, as well as
water is observed. movement in horizontal and vertical
9. General damage of buildings directions. Numerous landslips and
i) General panic; considerable damage falls of rocks. The intensity of
to furniture, Animals run to and fro the earthquake requires to be
in confusion, and cry. investigated specifically.
ii) Many buildings of Type C suffer 12. Lundscape changes
damage of Grade 3, and few of i) Practically all structures above and
Grade 4. Most buildings of Type B below &ound are greatly damaged
show a damage of Grade 4 and a few or destroyed.
of Grade 5. Many buildings of ii) The surface of the ground is radically
Type A suffer damage of Grade 5. changed. Considerable ground
Monuments and columns fall. cracks with extensive vertical and
Considerable damage to reservoirs; horizontal movements are observed.
underground p@es partly broken. In Falling of rock and slumping of river
individual cases, railway lines are banks over wide areas, lakes are
bent and roadway damaged. damaged, waterfalls appears and
iii) On flat land overflow of water, sand rivers are deflected. The intensity
and mud is often observed. Ground of the earthquake requires to be
cracks in widths of up to 10 cm on investigated specially.

98 NATIONAL BUILDING CODE OF INDIA


ANNEX J

(Clause 5.3.4.2)
ZONE FACTORS FOR SOME IMPORTANT TOWNS

Town Zone Zone Factor, Z Town Zone Zone Factor, Z


Agra III 0.16 Goa III 0.16
Ahmedabad III 0.16 Gulbarga II 0.10
Ajmer II 0.10 Gaya” III 0.16
Allahabad II 0.10 Gorakhpur IV 0.24
Almora IV 0.24 Hyderabad II 0.10
Ambala IV 0.24 Imphal v 0.36
Amritsar IV 0.24 Jabalpur III 0.16
Asansol III 0.16 Jaipur II 0.10
Aurangabad II 0.10 Jamshedpur II 0.10
Bahraich IV 0.24 Jhansi II 0.10
Bangalore II 0.10 Jodhpur II 0.10
Barauni IV 0.24 Jorhat v 0.36 ,,..
Bareilly III 0.16 Kakrapara III 0.16
Belgaum III 0.16 Kalapakkam III 0.16
Bhatinda III 0.16 Kanchipuram III 0.16
Bhilai II 0.10 Kanpur III 0.16
Bhopal II 0.10 Karwar III 0.16
Bhubaneshwar III 0.16 Kohima v 0.36
Bhuj v 0.36 Kolkata III 0.16
Bijapur III 0.16 Kota II 0.10
Bikaner III 0.16 Kumool II 0.10
Bokaro III 0.16 Lucknow III 0.16
Bulandshahr Iv 0.24 Ludhiana IV 0.24
Burdwan III 0.16 Madurai II 0.10
Calicut III 0.16 Mandi v 0.36
Chandigarh IV 0.24 Mangalore II 0.16
Chennai III 0.16 Monghyr IV 0.24
Chitradurga II 0.10 Moradabad Iv 0.24
Coimbatore III 0.16 Mumbai III 0.16
Cuddalore 111 0.16 Mysore II 0.10
Cuttack III 0.16 Nagpur H 0.10
Darbhanga v 0.36 Nagarjunasagar II 0.10
Dmjeeling IV 0.24 Nainital Iv 0.24
Dharwad III 0.16 Nasik III 0.16
Debra Dun IV 0.24 Nellore III 0.16
Dharampuri III 0.16 Osmanabad III 0.16
Delhi IV 0.24 Panjim III 0.16
Durgapur III 0.16 Patiala III 0.16
Gangtok IV 0.24 Patna IV 0.24
Guwahati v 0.36 Pilibhit Iv 0.24

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 99


Town Zone Zone Factor, Z Town Zone Zone Factor, Z
Pondicherry II 0.10 Tarapur III 0.16
Pune III 0.16 Tezpur v 0.36
Raipur II 0.10 Thane III 0.16
Rajkot III 0.16 Thanjavur II 0.10
Ranchi II 0.10 Thirnvananthapuram III 0.16
Roorkee IV 0.24
Tiruchchirappalli II 0.10
Rourkela II 0.10
Tiruvennamalai III 0.16
Sadiya v 0.36
Udaipur II 0.10
Salem 111 ; 0.16
Vadodara III 0.16
Shimla IV : 0.24
Varanasi III 0.16
Sironj II 0.10
Solapur III 0.16 Vellore III 0.16
Srinagar v 0.36 Vijayawada . III 0.16
Surat III 0.16 Vishakhapatnam II 0.10

-.
ANNEX K

(Clauses 6.4.2.4 and 6.4.3)


SHAPE COEFFICIENTS FOR MULTILEVEL ROOFS

A more comprehensive formula for the shape coefficient for multilevel roofs

< WINDDIRECTION

~h—-+---k-----J

r
-I IJl
L
l-----l+ 7
Restriction:
h = 1 + + (m,l, + m,l,) (12–2h)
+
K, = 0.8 0

1, = 2h where
(h and 1 being in metres) SOis in kilopascals (kilonewtons per square metre)

100 NATIONAL BUILDING CODE OF INDIA


k is in newtons per cubic metre 0.3 for plane roofs with
fl
l,<15m slopes ~ <20° and vaulted roofs with ~ ~ ~

Values of ml (m2) for the higher (lower) roof depend The coefllcients ml and m2 may be adjusted to take
on its profile and are taken as equal to: into account conditions for transfer of snow on the roof
0.5 for plane roofs with surface (that is wind, temperature, etc).
fl
slopes (3<20° and vaulted roofs with — S — NOTE — The other condition of loading shatl also be tried.
118

ANNEX L

(Clause 7.7)

VIBRATIONS IN BUILDINGS

L-1 GENERAL L-2 SERVICEABILITY LIMIT STATE


VERIFICATION OF STRUCTURE SUSCEPTIBLE
In order to design the buildings safe against vibrations,
TO VIBRATIONS
it is necessary to identify the source and nature of
vibration. Vibrations may be included in the buildings L-2.1 While giving guidance for serviceability limit
due to various actions, such as: state verification of structure susceptible to vibrations,
a) human induced vibrations, for example, the here it is proposed to deal with the treatment of the
action side, the determination of the structural response
walking or running or a single person or a
number of persons or dancing or motions in and the limits to be considered for the structural
stadia or concert halls; response to ensure that vibrations are not harmful or
do not lead to discomfort.
b) machine induced vibrations;
c) wind induced vibrations; L-2.2 Source of Vibrations
d) blast induced vibrations;
Vibrations may be included by the following sources:
e) traffic load, for example, due to rail, fork-lift,
trucks, cars, or heavy vehicles; a) by the movement of persons as in pedestrian
bridges, floors where people walk, floors
f) airborne vibrations;
meant for sport or dancing activities, and
@ crane operations; and
floors with fixed seating and spectator
h) other dynamic actions, such as, wave loads galleries;
or earthquake actions.
b) by working of machines as in machine
The dynamic response of buildings for the above foundations and supports, vibrations
mentioned causes of vibration of buildings may have transmitted through the ground, and pile
to be evaluated by adopting standard mathematical driving operations;
models and procedures. c) by wind blowing on buildings, towers,
chimneys mid masts, guyed masts, pylons,
The severity or otherwise of these actions have to be
bridges, cantilevered roofs, airborne
assessed in terms of the limits set for dynamic response
vibrations;
(frequencies and amplitude of motion) of the buildings
related to (a) human comfort, (b) serviceability d) induced by traffic on rail or road bridges
requirements, such as, deflections and drifts and and car park structures and exhibition halls;
separation distances to avoid damage due to pounding, and
and (c) limits set on the frequencies and amplitude of e) by earthquakes.
motion for machines and other installations.
L-2.3 Modelling of Actions and Structures
In order to verify that the set limits are not exceeded,
For serviceability limit states, the modelling of these
the actions may be modelled in terms of force-time
actions and of the structure depends on how the
histories for which the structural responses may be
serviceability limits are formulated. The serviceability
determined as time histories of displacements or
limit states may refer to:
accelerations by using appropriate analytical/numerical
methods. a) human comfort,

PART 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 101


T--

b) limits for the proper functioning of machines L-2.4 Force-Time Histories


and other installations, and
The force-time histories used in the dynamic analysis
c) maximum deformation limits to avoid damage should adequately represent the relevant loading
or pounding. situations for which the serviceability limits are to be
In order to verify that these limits are not exceeded, verified. The force-time histories may model:
the actions may be modelled in terms of force-time a) human induced vibrations, for example the
histories, for which the structural responses may be walking or running of a single person or a
determined as time histories of displacements or number of persons or dancing or motions in
accelerations by using appropriate analytical/ stadia or concert halls;
numerical methods. Where the structural response b) machine induced vibrations, for example by
may significantly influence the force-time histories
force vectors due to mass eccentricities and
to be applied, these interactions have to be
frequencies, that may be variable with time;
considered either in modelling a combined load-
c) wind induced vibrations;
structure vibration system or by appropriate
d) blast induced vibrations;
modifications of the force-time histories. In addition
to the levels of vibration for which presently limits e) traftlc load, for example rail, fork-lift, trucks,
have been specified, the possible deformations of cars, or heavy vehicles;
structural members and systems using different 0 airborne vibrations;
clauses in the relevant codes have to be evaluated g) crane operations; and
by adopting standard mathematical models and h) other dynamic actions such as wave loads or .-.
procedures. earthquake actions.

ANNEX M

(Clause 9.2)

SUMMARY OF DISTRICTS HAVING SUBSTANTIAL MULTI-HAZARD RISK AREAS

State Name of Districts Having Substantial Multi-hazard Prone Area

E.Q. and Flood Cyclone and Flood E.Q. Cyclone and Flood E.Q. and Cyclone
(1) (2) (3) (4) (5)

Andhra Adilabad, Karim Krishna, Nellore, East Godavari, Guntur, —


Pradesh Nagar, Khammam Srikakulam, Prakasam, West Godavari
Vishakhapatnam,
Vizianagram
Assam All 22 districts listed No cyclone, but speed — —
in Table 38 could can be 50 mls in districts
have M.S.K. IX or of Table 38 causing local
more with flooding damage except Dhubri
Bihar All 25 districts listed — — —
in Table 38
Goa — — North and south
Goa
Gujarat Banaskantha, Danthe — Ahmedabad, Bhamch, Amreli,
GS, Gandhinagar, Surat, Valsad Bhavnagar,
Kheda, Mahesana, Jamnagar, RajkoC
Panchmahals, Junagad, Kachcha
Vadodara
Haryana All 8 districts listed — — —
in Table 38

102 NATIONAL BUILDING CODE OF INDIA


(1) (2) (3) (4) (5)
-- -. — .
ldduki, Kottayam, Palakkad, — Alappuzh% Emakulum,
Pathanamthitta Kamur, Kasargode,
Kollam, Kozhikode,
Malappuram,
Thiruvartathapuram,
Tnssur
Maharashtra — — . Bombay, Rayagad,
Ratnagiri,
Sindhudurg, Thane
Orissa — Ganjam Baleshwar, Dhenkamd
Cuttack, Puri
Punjab AII 12 districts listed in — — —
Table 38
Uttar Pradesh All 50 districts listed in — — —
Table 38
West Bengal Birbhum, D~”eeling, Bardhaman, Calcutt& Bankura
Jalpaiguri, Kooch Bihar, Hugli, Howra, Mednipur,
MaIda, Murshidabad, Nadia, North and South
West Dinajpur 24 Parganas
Union Delhi — Yanam (Py) Diu
Territories
India 139 Districts 6 Districts 29 Districts 16 Districts

Table 38 Multi-Hazard Prone Districts

Assam 4Pmi,jab
Barpeta, Bongaigaon, CacharlJ, Darrang, Dhemaji, Dhuburi, Amritsar, Bathinda, Faridkot, FiIozpur, Gurdaspur, Hoshisrrpur,
Dibrugarh, Goalpara, Golaghat, Hailaknadil), )orhat, Kamrup, Jrdsmdhar,Kaputthala, Ludtriarta, Patiata, Rup Nagar, Sangrur
Karbianglong, Karimganj 1),Kokrajhar, Lakhimpur, Morigaon, 5)Ut~r fiad~h
Nagaon, Nalbari, Sibsagar, Sonitpur, Tinsrrkia
Agra, Aligarh, Allahabad, Azamgarh, Bahraich, Bahia,
Biharzl Barabanki, Bareilly, Basti, Bijnor, Btrdaun, Bulandshahr, Deoria,
Araria, Begusarai, Bhagalpur, Bhojpur, Darbhrrnga, Gopalganj, Etah, Etawah, Faizabad, Farrukhabad, Fatehpur, Firozabad,
Katihar, Khagaria, Kishanganj, Madhepttra, Madhubani, Munger, Ghaziabad, Ghazipur, Gonda, Gorakhpur, Hardoi, Haridwar,
Muzaffarpur, Nalanda, Nawada, Paschim Champaran, Patna, Jaunpur, Kanpur (Dehat), Karrpur (Nagar), Kheri, Lucknow,
Purbachamparan, Pumia, Samastipur, Saran, Saharsa, Sitamarhi, Maharajganj, Mainpuri, Mathura, Mau, Meerut, Mirzapur,
Siwan, Vaishali Mordabad, Muzaffarnagar, Nainital, Pilibhit, Partapgarh,
Raebareli, Rampur, Srrharanpur, Shabjahrmpur, Siddartfr Nagar,
3JHaryana Sitapur, Sultanpur, Unnao, Varattasi
Ambala, Bhiwani, Faridabad, Gurgaon, Hissar, find, Ktrrukshetra,
Rohtak

~1 Districts liable to cycloNc storm but NO storm surge


a No Cyclonicstorm in Bihar
J) No ~Yclonicstorm in HWana
4) NO cyclonic storm in Punjab
$ NO cyclonic storm in Uttar Prarfesh

LIST OF STANDARDS

The following list records those standards which are with the requirements of the referred clauses in the
acceptable as ‘good practice’ and ‘accepted standards’ Code.
in the fulfilme~t of ~he requirements OFthe Code. The
In the following list, the number appearing in the fwst
latest version of a standard shall be adopted at the time
of enforcement of the Code. The standards listed may column within parentheses indicates the number of the
be used by the Authority as a guide in conformance reference in this Part/Section.

PARI’ 6 STRUCTURAL DESIGN — SECTION 1 LOADS, FORCES AND EFFECTS 103


1S No. Title IS No. Title

(1) 875 Code of practice for design (7) 1498:1970 Classification and identification
(Part 1): 1987 loads (other than earthquake) of soils for general engineering
for buildings and structures purposes @rst revision)
Part 1 Dead loads — Unit (8) 2131:1981 Method for standard penetration
weights of building material test for soils (@t revision)
and stored materials (second
(9) 4326:1993 Code of practice for earthquake
revision)
resistant design and construction
(2) 8888 Guide for requirements of low of buildings (second revision)
(Part 1) :1993 income housing: Part 1 Urban
(10) 3414:1968 Code of practice for design
area (jirst revision)
and installation of joints in
(3) 807:1976 Code of practice for design,
buildings
manufacture, erection and
(11) 1642:1989 Code of practice for fire safety
testing (structural portion)
of buildings (general): Details
of cranes and hoists ($irst
of construction @st revision)
revision)
3177:1999 Code of practice for electric (12) 15498:2004 Guidelines for improving
overhead traveling cranes cyclone resistance of low rise
and gantry cranes other than houses and other buildings/
structures ....
steelwork cranes (second
revision) (13) 14458 Guidelines for retaining wall
(4) 3920:1993 Code of practice for ductile (Part 1): 1998 for hill area Part 1 Selection
detailing of reinforced concrete of type of wall
structures subjected to seismic (14) 14458 Guidelines for retaining wall
forces (Part 2): 1997 for hill area: Part 2 Design of
(5) 893 Criteria for earthquake resistant retaining/breast walls
(Part 4): 2005 design of structures: Part 4 (15) 14458 Guidelines for retaining
Industrial structures including (Part 3): 1998 wall for hill area: Part 3
stack-like structures Construction of dry stone
(6) 1888:1982 Method of load test on soils (16) 14496 Guidelines for preparation of
(second revision) (Part 2): 1998 landslide-hazard zonation
6403:1981 Code of practice for maps in mountainous terrains:
determination of bearing Part 2 Macro-zonation
capacity of shallow foundations (17) 14680:1999 Guidelines for landslide
(jirst revision) control

104 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 2 Soils and Foundations

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 SITE INVESTIGATION ... 7
4 CLASSIFICATION AND IDENTIFICATION OF SOILS ... 11
5 MATERIALS ... 11
6 TYPE OF FOUNDATIONS ... 11
7 SHALLOW FOUNDATIONS ... 11
8 DRIVEN/BORED CAST ZN-SITU CONCRETE PILES ... 22
9 DRIVEN PRECAST CONCRETE PILES ... 27
10 BORED PRECAST CONCRETE PILES ... 28
11 UNDER-REAMED PILES ... 29
12 TIMBER PILES ... 31
13 OTHER FOUNDATIONS ... 32
14 GROUND IMPROVEMENT ... 32

ANNEX A DETERMINATION OF MODULUS OF ELASTICITY (E,) AND ... 33


POISSON’S RATIO (p)
ANNEX B DETERMINATION OF MODULUS OF SUBGRADE REACTION ... 34
ANNEX C RIGIDITY OF SUPERSTRUCTURE AND FOUNDATION ... 35
ANNEX D CALCULATION OF PRESSURE DISTRIBUTION BY . .. 36
CONVENTIONAL METHOD
ANNEX E CONTACT PRESSURE DISTRIBUTION AND MOMENTS ... 37
BELOW FLEXIBLE FOUNDATION
ANNEX F FLEXIBLE FOUNDATION — GENERAL CONDITION ... 38
ANNEX G LOAD CARRYING CAPACITY — STATIC FORMULA ... 39
ANNEX H DETERMINATION OF DEPTH OF FIXITY, LATERAL . .. 42
DEFLECTION AND MAXIMUM MOMENT
ANNEX J LOAD CARRYING CAPACITY OF UNDER-REAMED PILES ... 44
FROM SOIL PROPERTIES

LIST OF STANDARDS ... 45

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Section deals with the structural design aspects of foundations and mainly covers the design principles
involved in different types of foundations.

This Section was published in 1970, and subsequently revised in 1983. In the first revision design considerations
in respect of shallow foundation were modified, provisions regarding pier foundation were added and provisions
regarding draft foundation and pile foundation were revised and elaborated.

As a result of experience gained in implementation of 1983 version of the Code and feed back received as well
as revision of standards and preparation of new standards in the field of soils and foundations, a need to revise
this Section was felt. This revision has therefore been prepared to take into account these developments. The
significant changes incorporated in this revision include:

a) Design considerations in respect of shallow foundations have been modified.


b) Method for determining depth of fixity, lateral deflection and maximum moment have been modified.
c) Reference has been made to ground improvement techniques.
d) References to Indian Standards made in the text have been updated.

For detailed information regarding structural analysis and soil mechanics aspects of individual foundations,
reference should be made to standard textbooks and available literature.

The information contained in this Section is mainly based on the following Indian Standards:

IS No. Title
1080:1985 Code of practice for design and construction of shallow foundations in soils
(other than raft, ring and shell) (second revision)
1904:1986 Code of practice for design and construction of foundations in soils: General
requirements (third revision)
2911 (Part l/See 1) :1979 Code of practice for design and construction of pile foundations: Part 1 Concrete
piles, Section 1 Driven cast in-situ concrete piles (first revision)
2911 (Part l/See 2) :1979 Code of practice for design and construction of pile foundations: Part 1 Concrete
piles, Section 2 Bored cast in-situ piles (first revision)
2911 (Part l/See 3) :1979 Code of practice for design and construction of pile foundations: Part 1 Concrete
piles, Section 3 Driven precast concrete piles (first revision)
2911 (Part l/See 4) :1984 Code of practice for design and construction of pile foundations: Part 1 Concrete
piles, Section 4 Bored precast concrete piles
2911 (Part 3) :1980 Code of practice for design and construction of pile foundations: Part 3 Under-
reamed piles (first revision)
2950 (Part 1) :1981 Code of practice for design and construction of raft foundations: Part 1 Design
(second revision)
9456:1980 Code of practice for design and construction of conical hyperbolic paraboidal
types of shell foundations

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 3


. ---
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 2 Soils and Foundations

1 SCOPE of particles of size greater than 0.075 mm and less


than 0.425 mm.
This Section covers structural design (principles) of
all building foundations such as raft, pile and other 2.1.11 Sand, Medium — Sand which contains
foundation systems to ensure safety and serviceability 50 percent of particles of size greater than 0.425 mm
without exceeding the permissible stresses of the and less than 2.0 mm.
materials of foundations and the bearing capacity of 2.1.12 Silt — A fine grained soil with little or no
the supporting soil. plasticity. The size of particles ranges from 0.075 mm
to 0.002 mm.
2 TERMINOLOGY
2.1.13 soft Rock — A rocky cemented material which
2.0 For the purpose of this Section, the following offers a high resistance to picking up with pick axes
definitions shall apply. and sharp tools but which does not normally require
blasting or chiseling for excavation.
2.1 General
2.1.14 Soil, Black Cotton — Inorganic clays of
2.1.1 Clay — An aggregate of microscopic and
medium to high compressibility y. They form a major
sub-microscopic particles derived from the chemical
soil group in India. They are predominately
decomposition and disintegration of rock constituents.
montmorillonitic in structure and yellowish black or
It is plastic within a moderate to wide range of water
blackish grey in colour. They are characterized by high
content. The particles are less than 0.002 mm in size.
shrinkage and swelling properties.
2.1.2 Clay, Firm — A clay which at its natural water 2.1.15 Soil, Coarse Grained — Soils which include
content can be moulded by substantial pressure with the coarse and largely siliceous and unaltered products
the fingers and can be excavated with a spade. of rock weathering. They possess no plasticity and tend
2.1.3 Clay, Soft — A clay which at its natural water to lack cohesion when in dry state.
content can be easily moulded with the fingers and
2.1.16 Soil, Fine Grained — Soils consisting of the
readily excavated.
fine and altered products of rock weathering,
2.1.4 Clay, Stifi— A clay which at its natural water possessing cohesion and plasticity in their natural state,
content cannot be moulded with the fingers and the former even when dry and both even when
requires a pick or pneumatic spade for its removal. submerged. In these soils, more than half of the material
2.1.5 Foundation — That part of the structure which by weight is smaller than 75-micron IS Sieve size.
is in direct contact with and transmits loads to the 2.1.17 Total Settlement — The total downward
ground. movement of the foundation unit under load.
2.1.6 Gravel — Cohesionless aggregates of angular 2.2 Shallow Foundation
rounded or semi-rounded, fragments of more or less
unaltered rocks or minerals, 50 percent or more of the 2.2.1 Back Fill — Materials used or re-used to fill an
particles having size greater than 4.75 mm and less excavation.
than 80 mm. 2.2.2 Bearing Capacity, Safe — The maximum
2.1.7 Peat — A fibrous mass of organic matter in intensity of loading that the soil will safely carry with
various stages of decomposition generally dark brown a factor of safety without risk of shear failure of soil
to black in colour and of spongy consistency. irrespective of any settlement that may occur.
2.1.8 Sand — Cohesionless aggregate of rounded, sur- 2.2.3 Bearing Capaci@, Ultimate — The intensity of
rounded, angular, sub-angular or flat fragments of more loading at the base of a foundation which would cause
or less unaltered rock or minerals, 50 percent or more shear failure of the supporting soil.
of particles greater than 0.075 mm or less
2.2.4 Bearing Pressure, Allowable (Gross or Net) —
than 4.75 mm in size.
The maximum allowable loading intensity on the
2.1.9 Sand, Coarse — Sand which contains 50 percent ground in any given case (with full cognizance of
or more of particles of size greater than 2 mm and less surcharge) taking into account the maximum safe
than 4.75 mm. bearing capacity, the amount and kind of settlement
2.1.10 Sand, Fine — Sand which contains 50 percent expected and the capability of the structure to take up

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 5


this settlement. It is, therefore, a combined function of ‘End Bearing Pile’, if support is provided primarily by
both the site conditions and characteristics of the friction along its surface, it is referred to as ‘Friction File’.
particular structure.
2.3.3 Bored Cast in-situ Pile — The pile formed within
The net allowable bearing pressure is the gross allowable the ground by excavating or boring a hole within it,
bearing pressure minus the surcharge intensity. with or without the use of a temporary casing and
NOTE — The concept of ‘gross’ and ‘net’ used in defining subsequently tilling it with plain or reinforced concrete.
the allowable bearing pressure could also be extended to safe When the liner is left permanently it is termed as cased
bearing capacity, safe bearing pressure and ultimate bearing pile and when the casing is taken out it is termed as
capacity. uncased pile.
2.2.5 Factor of Safety (with Respect to Bearing In installing a bored pile the sides of the borehole (when
Capacity) — A factor by which the ultimate bearing it does not standby itself) are required to be stabilized
capacity (net) must be reduced to arrive at the value of with the aid of a tempormy casing, or with the aid of
safe bearing capacity (net). drilling mud of suitable consistency. For marine
2.2.6 Footing — A spread constructed in brick work, situations such piles are formed with permanent casing
masonry or concrete under the base of a wall or column (liner).
for the purpose of distributing the load over a larger 2.3.4 Bored Compaction Pile — A bored cast in-situ
area. pile with or without bulb(s) in which the compaction
2.2.7 Foundation, Raft — A substructure supporting an of the surrounding ground and freshly filled concrete
arrangement of columns or walls in a row or rows in pile bore is simultaneously achieved by a suitable
transmitting the loads to the soil by means of a continuous method. If the pile is with bulb(s), it is known as under-
slab, with or without depressions or openings. reamed bored compaction pile.

2.2.8 Make-up Ground — Refuse, excavated soil or 2.3.5 Bored Pile — A pile formed with or without
rock deposited for the purpose of filling a depression or casing by excavating or boring a hole in the ground
raising a site above the natural surface level of the and subsequently filling it with plain or reinforced
ground. concrete,

2.2.9 Offset — The projection of the lower step from 2.3.6 Bored Precast Pile — A pile constructed in
the vertical face of the upper step. reinforced concrete in a casting yard and subsequently
lowered in the pre-bored holes and the space around
2.2.10 Permanent Load — Loads which remain on grouted.
the structure for a period, or a number of periods, long
enough to cause time dependent deformation 2.3.7 Cut-offLevel — It is the level where the installed
settlement of the soil. pile is cut-off to connect the pile caps or beams or any
other structural components at that level.
2.2.11 Shallow Foundation — A foundation whose
width is generally equal to or greater than its depth. 2.3.8 Driven Cast in-situ Pile — A pile formed within
the ground by driving a casing of permanent or
NOTE — These cover such types of foundations in which load
transference is primarily through shear resistance of the bearing
temporary type and subsequently filling in the hole so
strata (the frictional resistance of soil above bearing strata is not formed with plain or reinforced concrete. For
taken into consideration) and are laid normally to depth of 3 m. displacing the subsoil, the casing is installed with a
2.2.12 Spread Foundation — A foundation which plug or a shoe at the bottom end. When the casing is
left permanently, it is termed as cased pile and when
transmits the load to the ground through one or more
the casing is taken out, it termed as uncased pile.
footings.
2.3.9 Driven Precast Pil; — A pile constructed in
2.3 Pile Foundation
concrete (reinforced or prestressed) in a casting yard
2.3.1 Batter Pile (Raker Pile) — The pile which is and subsequently driven in the ground when it has
installed at an angle to the vertical. attained sufficient strength.

2.3.2 Bearing Pile — A pile formed in the ground for 2.3.10 E@ciency of a Pile Group — It is the ratio of
transmitting the load of a structure to the soil by the the actual supporting value of a group of piles to the
resistance developed at its tip and/or along its surface. supporting value arrived at by multiplying the pile
It maybe formed either vertically or at an inclination resistance of an isolated pile by their number in the
(Batter Pile) and may be required to take uplift pressure. group.

If the pile supports the load primarily by resistance 2.3.11 Factor of Safety — It is the ratio of the ultimate
developed at the pile point or base, it is referred to as load capacity of a pile to the safe load of a pile.

6 NATIONAL BUILDING CODE OF INDIA


F---

2.3.12 Multi- Under-ReamedPile — An under-reamed for all types of formations, but should be used
pile having more than one bulb. The piles having two for small depths (up to 3 m). In the case of
bulbs may be called double under-reamed piles. cuts which cannot stand below water table,
proper bracing should be given.
2.3.13 Negative Skin Friction — Negative skin friction
b) Auger boring — The auger is either power of
is the force developed through the friction between
the pile and the soil in such a direction as to increase hand operated with periodic removal of the
the loading on the pile, generally due to drag of a cuttings.
consolidating soft layer around the pile resting on a c) Shell and auger boring — Both manual and
stiffer bearing stratum such that the surrounding soil mechanized rig can be used for vertical
settles more than the pile. borings. The tool normally consists of augers
for soft to stiff clays, shells for very stiff and
2.3.14 Ultimate Load CapaciQ — The maximum load hard clays, and shells or sand pumps for sandy
which a pile can carry before failure of ground when strata attached to sectional boring rods.
the soils fails by shear or failure of pile materials.
d) Wash boring — In wash boring, the soil is
2.3.15 Under-Reamed Pile — A bored cast in-situ or loosened and removed from the bore hole by
bored compaction concrete pile with enlarged bulb(s) a stream of water or drilling mud is worked
made by either cutting or scooping out the soil or by up and down or rotated in the bore hole. The
any other suitable process. water or mud flow carries the soil up the
annular space between the wash pipe and the
3 SITE INVESTIGATION casing, and it overflows at ground level,
3.1 General where the soil in suspension is allowed to
settle in a pond or tank and the fluid is re-
In areas which have already been developed,
circulated as required. Samples of the settled
information should be obtained regarding the existing
out soil can be retained for identification
local knowledge, records of trial pits, bore holes, etc,
purposes but this procedure is often
in the vicinity, and the behaviour of the existing
unreliable. However, accurate identification
structures, particularly those of a similar nature to those
can be obtained if frequent ‘dry’ sampling is
proposed. This information may be made use of for
resorted to using undisturbed sample tubes.
design of foundation of lightly loaded structures of not
e) Sounding/Probing including standard
more than two storeys and also for deciding scope of
penetration test, dynamic and static cone
further investigation for other structures.
penetration test
3.1.1 If the existing information is not sufficient or is f) Geophysical method
inconclusive, the site should be explored in detail as
g) Percussion boring and rotary boring
per good practice [6-2(1)] so as to obtain a knowledge
h) Pressure meter test
of the type, uniformity, consistency, thickness,
sequence and dip of the strata, hydrology of the area 3.2.2 Number and Disposition of Test Locations
and also the engineering properties. In the case of
The number and disposition of various tests shall
lightly loaded structures of not more than two storeys,
depend upon type of structure/buildings and the soil
the tests required to obtain the above information are
strata variations in the area. General guidelines are,
optional, mainly depending on site conditions.
however, given below:
Geological maps of the area give valuable information
of the site conditions. The general topography will a) For a compact building site covering an area
often give some indications of the soil conditions and of about 0.4 hectare, one bore hole or trial pit
their variations. In certain cases the earlier uses of the in each comer ‘and one in the centre should
site may have a very important bearing on the proposed be adequate. “
new structures. b) For smaller and less important buildings, even
one bore hole or trial pit in the centre will
3.2 Methods of Site Exploration
suffice.
3.2.1 The common methods of site exploration are
c) For very large areas covering industrial and
given below:
residential colonies, the geological nature of
a) Open trial pits — The method consists of the terrain will help in deciding the number of
excavating trial pits and thereby exposing bore holes or trial pits. For plant and other main
the subsoil surface thoroughly, enabling structures, number of bore holes amlor trial
undisturbed samples to be taken from the sides pits should be decided considering importance
and bottom of the trial pits. This is suitable of structure and type as well as uniformity of

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 7


strata. In general, dynamic or static cone 3.3.1 Nature of Ground
penetration tests may be performed at
a) Soils — In clayey soils, borings are suitable
every 100 m by dividing the area in a grid
for deep exploration and pits for shallow
pattern and the number of bore holes or trial
exploration. In case of soft sensitive clayey
pits may be decided by examining the variation
soils field vane shear test may be carried out
in the penetration curves. The cone penetration
with advantage.
tests may not be possible at sites having
generally bouldery strata. In such cases, In sandy soils, special equipments may be
required for taking representative samples
geophysical methods should be resorted to.
below the water table. Standard penetration
3.2.3 Depth of Exploration test, dynamic cone penetration test and static
The depth of exploration required depends on the type cone penetration test are used to assess
of proposed structure, its total weight, the size, shape engineering properties.
and disposition of the loaded areas, soil profile, and b) Gravel-boulder deposits — In the deposits
the physical properties of the soil that constitutes each where gravel-boulder proportion is large
individual stratum. Normally, it should be one and a (>30 percent), the sub-soil strata should be
half times the width of the footing below foundation explored by open trial pits of about 5 m x
level. In certain cases, it maybe necessary to take at 5 m but in no case less than 2 m x 2 m. The
least one bore hole or cone test or both to twice the depth of excavation may be up to 6 m. For
width of the foundation. If a number of loaded areas determining strata characteristics, in-situ
are in close proximity the effect of each is additive. In tests should be preferred. For shear
such cases, the whole of the area may be considered characteristics and allowable soil pressure
as loaded and exploration should be carried out up to dynamic cone penetration tests, load tests on
one and a half times the lower dimension. In weak soils, cast in-situ footing and in-situ shear tests that
the exploration should be continued to a depth at which is, boulder-boulder test or concrete-boulder
the loads can be carried by the stratum in question test are more appropriate. For detailed
without undesirable settlement and shear failure. In any information on these tests reference may be
case, the depth to which seasonal variations affect the made to good practice [6-2(2)]. Depending
soil should be regarded as the minimum depth for the on the structure, if required, the strata may
exploration of sites. But where industrial processes be explored by drilling bore hole using
affect the soil characteristics this depth may be more. suitable method.
The presence of fast growing and water seeking trees c) Rocks — Drillings are suitable in hard rocks
also contributes to the weathering processes. and pits in soft rocks. Core borings are
NOTE — Examples of fast growing and water seeking trees are
suitable for the identification of types of rock,
Banyan (Ficusbengalensis),Pipat (Ficus religiosa)and Neem but they cannot supply data on joints and
(Az.adirachtaindica). fissures which can be examined only in pits
and large diameter borings.
3.2.3.1 An estimate of the variation with depth of the
vertical normal stress in the soil arising from foundation 3.3.2 Topography
loads may be made on the basis of elastic theory. The
In hilly country, the choice between vertical openings
net loading intensity at any level below a foundation
(for example, borings and trial pits) and horizontal
may be obtained approximately by assuming a spread
openings (for example, headings) may depend on the
of load of two vertical to one horizontal from all sides
geological structure, siilce steeply inclined strata are
of the foundations, due allowance being made for the
most effectively exploredoby headings and horizontal
overlapping effects of load from closely spaced footings.
strata by trial pits or b6rings. Swamps and areas
As a general guidance, the depth of exploration at the
overlain by water are best explored by borings which
start of the work may be decided as given in Table 1,
may require use of a floating craft.
which may be modified as exploration proceeds, if
required. However, for plant and other main structures, 3.3.3 cost
the depth of exploration maybe decided depending upon
For deep exploration, borings are usual, as deep shafts
importance of structure, loading conditions and type as
are costly. For shallow exploration in soil, the choice
well as uniformity of strata.
between pits and borings will depend on the nature of
3.3 Choice of Method for Site Exploration the ground and the information required for shallow
exploration in rock, the cost of bringing a core drill to
The choice of the method depends on the following
the site will be justified only if several holes are
factors.
required; otherwise, trial pits will be more economical.

8 NATIONAL BUILDING CODE OF INDIA


Table 1 Depth of Exploration
(Clause 3.2.3.1)

S1 No. Type of Foundation Depth of Exploration


4

D i

(1) (2) (3)

i) Isolated spread footing or raft One and a half times the width (B) (see Fig. 1)
ii) Adjacent footings with clear spacing less One and a half times the length (L) of the footing (see Fig. 1)
than twice the width
iii ) Adjacent rows of footings See Fig. 1
iv) Pile and well foundations To a depth of one and a half times the width of structure from the bearing (toe of
pile or bottom of well)
v) a) Road cuts Equal to the bottom width of the cut
b) Fill Two metres below ground level or equal to the height of the fill whichever is greater

L B

9- B-9 ●

D=14BFORA94B

D=I$L FOR A<2B

L=W

w~
D=4+BFORA<2B

D=3BFORA>2B

u=l;t3FoRA74B

FIG. 1 DEPTH OF EXPLORATION

PART 6 STRIJCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 9


3.4 Sampling 3.4.2 Soil Samples

3.4.1 Methods of Sampling a) Disturbed soil samples — The mass of sample


generally required for testing purposes is
a) Disturbed samples — These are taken by
given in Table 2.
methods which modify or destroy the natural
b) Undisturbed soil samples — The minimum
structure of the material though with suitable
diameter of the sample shall be 38 mm with
precautions the natural moisture content can
the minimum length/diameter ratio of 2.
be preserved.
b) Undisturbed samples — These are taken by 3.4.3 Rock Sample
methods which preserve the structure and a) Disturbed samples — The sludge from
properties of the material. Such samples are percussion borings, or from rotary borings
easily obtained from most rocks, but which have failed to yield a core, may be
undisturbed samples of soil can be obtained taken as a disturbed sample.
only by special methods. Thin walled tube
b) Undisturbed samples
samples may be used for undisturbed samples
1) Block samples — Such samples taken
in soils of medium strength and tests for the
from the rock formation shall be dressed
same may be carried out in accordance with
to a size convenient for packing to
good practice [6-2(1)].
about 90 mm x 75 mm x 50 mm.
NOTE — In case of loose sandy soils and soft soils,
specially below water table it may not be possible to 2) Core sample; see also good practice
take undisturbed sample, in which case other suitable [6-2(3)]
methods may be adopted for exploration.
3.4.4 Protection, Handling and L.ubelling of Samples
c) Representative samples — These samples
have all their constituent parts preserved, but Care should be taken in protecting, handling and
may or may not be structurally disturbed. subsequent transport of samples and in their full
labelling, so that samples can be received in a fit state
3.4.1.1 The methods usually employed a“e:
for examination and testing, and can be correctly
recognized as coming from a specified trial pit or
(A’ature of Type of Method of Sampling
boring.
Ground Sample
(1) (2) (3) 3.4.5 Examination and Testing of Samples

Soil Disturbed Chunk samples 3.4.5.1 The following tests shall be carried out in
Auger samples (for accordance with good practice [6-2(4)].
example, in clay) a) Particle size distribution,
Shell samples (for
b) Density,
example, in sand)
Undisturbed Chunk samples c) Natural moisture content,
Tube samples d) Consistency limits,
Rock Disturbed Wash samples from e) Consolidation characteristics,
percussion of rotary f) Strength characteristics,
drilling
Sulphate, chloride and pH content of soil and
g)
Undisturbed Core barrel sampling
ground water, and
,
Table 2 Mass of Soil Sample Required ~~
[Clause 3.4,2(a)]

S1 Purpose of Sample Type I@aii of Sample Required


No. kg
(1) (2) (3) (4)

i) Soil identification, natural moisture content tests, Cohesive soil 1


mechanical analysis, and index properties
Chemical tests Sands and gravels 3
ii) Compaction tests Cohesive soils and sands 12.5
Gravely soils 25
iii) Comprehensive examination of construction Cohesive soils and sands 25 to 50
matenats including stabilization Gravely soits .50to 100

10 NATIONAL BUILDING CODE OF INDIA


h) Differential free swelling and swelling 7 SHALLOW FOUNDATIONS
pressure.
7.0 Design Information
4 CLASSIFICATION AND IDENTIFICATION For the satisfactory design of foundations, the
OF SOILS following information is necessary:
The classification and identification of soils for a) The type and condition of the soil or rock to
engineering purposes shall be in accordance with good which the foundation transfers the loads;
practice [6-2(5)].
b) The general layout of the columns and load-
bearing walls showing the estimated loads,
5 MATERIALS
including moments and torques due to various
5.1 Cement, coarse aggregate, fine aggregate, lime, loads (dead load, imposed load, wind load,
SURKHI, steel, timber and other materials go into the seismic load) coming on the foundation units;
construction of foundations shall conform to the c) The allowable bearing pressure of the soils;
requirements of Part 5 ‘Building Materials’.
d) The changes in ground water level, drainage
5.2 Protection Against Deterioration of Materials and flooding conditions and also the chemical
conditions of the subsoil water, particularly
Where a foundation is to be in contact with soil, water with respect to its sulphate content;
or air, that is, in a condition conducive to the The behaviour of the buildings, topography
e)
deterioration of the materials of the foundation,
and environmenth.uroundings adjacent to the
protective measures shall be taken to minimize the
site, the type and depths of foundations and
deterioration of the materials.
the bearing pressure assumed; and
5.2.1 Concrete f-) Seismic zone of the region.

In the case of concrete placed against a soil containing 7.1 Design Considerations
harmful chemicals (sulphates, chlorides), among other
protective measures, it shall be ensured to provide 7.1.1 Design Loads
nominal cover required as prescribed in Part 6 The foundation shall be proportioned for the following
‘Structural Design, Section 5 Concrete for the combination of loads:
Applicable Environment Exposure Condition’.
a) Dead load + imposed load; and
5.2.1.1 Preferably concrete of higher grade shall be
b) Dead load + imposed load + wind load or
used in situations subject to aggressive environment.
seismic loads, whichever is critical.
5.2.2 Timber
For details, reference shall be made to Part 6 ‘Structural
Where timber is exposed to soil, it shall be treated in Design, Section 1 Loads, Forces and Effects’.
accordance with good practice [6-2(6)].
NOTES
1 For load, imposed, wind, seismic and other loads, see Part 6
6 TYPE OF FOUNDATIONS
‘Structural Design, Section 1 Loads, Forces and Effects’.
6.1 Types of foundations covered in this Section 2 For coarse grained soil$, settlements shall be estimated
are: corresponding to 7.1.1 (b) and for fine grrtined soils settlement
shall be estimated correspondi~ to permanent loads only.
a) Shallow Foundations
7.1.2 Allowable Bearing Pressure
1) Pad or spread and strip foundations,
2) Raft foundations, and The allowable bearing pressure shall be taken as either
of the following, whichever i’sless:
3) Ring and shell foundations.
b) Pile Foundations a) The safe bearing capacity on the basis of shear
1) Driven cast in-situ concrete piles, strength characteristics of soil, or
2) Bored cast in-situ concrete piles, b) The allowable bertring pressure that the soil
3) Driven precast concrete piles, can take without exceeding the permissible
settlement (see 7.1.3).
4) Bored precast concrete piles,
5) Under-reamed concrete piles, and 7.1.2.1 Bearing capacizy by calculation
6) Timber piles. Where the engineering properties of the soil are
c) Other Foundations available, that is, cohesion, angle of internal friction,
Pier foundations. density, etc the bearing capacity shall be calculated

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 11


from stability considerations of shear; factor of safety causes responsible for producing the settlement shall
of 2.5 shall be adopted for safe bearing capacity. The be investigated and taken into account.
effect of interference of different foundations should
a) Causes of settlement
be taken into account. The procedure for determining
1) Elastic compression of the foundation
the ultimate bearing capacity and allowable bearing
and the underlying soil;
pressure of shallow foundations based on shear and
allowable settlement criteria shall be in accordance 2) Consolidation including secondary
with good practice [6-2(7)]. compression;
3) Ground water lowering — Specially
7.1.2.2 Field method for determining allowable
repeated lowering and raising of water
bearing pressure
level in loose granular soils tend to
Where appropriate, plate load tests can be performed compact the soil and cause settlement of
and allowable pressure determined as per good practice the footings. Prolonged lowering of the
[6-2(8)]. The allowable bearing pressure for sandy soils water table in fine grained soils may
may also be obtained by loading tests. When such tests introduce settlement because of the
cannot be done, the allowable bearing pressure for extrusion of water from the voids.
sands may be determined using penetration test. Pumping water or draining water by tiles
or pipes from granular soils without an
7.1.2.3 Where the bearing materials directly under a
atiequate mat of filter material as
foundation over-lie a stratum having smaller safe
protection may, in a period of time, carry
bearing capacity, these smaller values shall not be
a sufficient amount of fine particles away
exceeded at the level of such stratum.
from the soil and cause settlement;
7.1.2.4 Effect of wind and seismic force 4) Seasonal swelling and shrinkage of
expansive clays;
Where the bearing pressure due to wind is less than 25
percent of that due to dead and live loads, it may be 5) Ground movement on earth slope, for
neglected in design. Where this exceeds 25 percent example, surface erosion, slow creep or
foundations may be so proportioned that the pressure due landslides; and
to combined dead, live and wind loads does not exceed 6) Other causes, such as adjacent
the allowable bearing pressure by more than 25 percent. excavation, mining, subsidence and
underground erosion.
When earthquake forces are considered for the
computation of design loads, the permissible increase b) Causes of differential settlements
in allowable bearing pressure of pertaining soil shall 1) Geological and physical non-uniformity
be as given in Table 3, depending upon the type of or anomalies in type, structure, thickness,
foundation of the structure. and density of the soil medium (pockets
of sand in clay, clay lenses in sand, wedge
7.1.2.5 Bearing capacity of buried strata like soil strata, that is, lenses in soil), an
If the base of a foundation is close enough to a strata admixture of organic matter, peat, mud;
of lower bearing capacity, the latter may fail due to 2) Non-uniform pressure distribution from
excess pressure transmitted to it from above. Care foundation to the soil due to non-uniform
should be taken to see that the pressure transmitted to loading and incomplete loading of the
the lower strata is within the pres&ibed safe limits. foundations;
When the footings are closely spaced, the pressure 3) Water regime at the construction site,
transmitted to the underlying soil will overlap. In such 4) Overstres@g of soil at adjacent site by
cases, the pressure in the overlapped zones will have heavy structures built next to light ones;
to be considered. With normal foundations, it is
5) Overlap of stress distribution in soil from
sufficiently accurate to estimate the bearing pressure
adjoining structures;
on the underlying layers by assuming the load to be
spread at a slope of 2 (vertical) to 1 (horizontal). 6) Unequal expansion of the soil due to
excavation for footing;
7.1.3 Settlement 7) Non-uniform development of extrusion
The permissible values of total and differential settlements; and
settlement for a given type of structure may be taken 8) Non-uniform structural disruptions or
as given in Table 4. Total settlements of foundation disturbance of soil due to freezing and
due to net imposed loads shall be estimated in thawing, swelling and softening and
accordance with good practice [6-2(10)]. The following drying of soils.

12 NATIONAL BUILDING CODE OF INDIA


Table 3 Percentage of Permissible Increase in A1lowable Bearing Pressure or
Resistance of Soils
(Clauses 7.1.2.4 and 8.2.7)

S1 Foundation Type of Soil Mainly Constituting the Foundation


No.

Type I — Rock or Hard Soil: Type II — Medium Type III — Soft Soils:
Well graded gravel and sand Soils: All soils with N All soils other than SP1)
gravel mixtures with or without between 10 and 30, and with N <10
clay binder, and clayey sands poorly graded sands or
poorly graded or sand clay gravelly sands with little
mixtures (GB, CW, SB, SW, and or no fines (SP1)) with
SC)l) having N*) above 30, where N> 15
N is the standard penetration
value

(1) (2) (3) (4) (5)

i) Piles passing through any soil but 50 50 50


resting on soil type I

ii) Piles not covered under item (i) 25 25

iii ) Raft foundations 50 50 50

iv) Combined isolated RCC footing 50 25 25


with tie beams

v) Isolated RCC footing without tie 50 25 -


beams, or unreinforced strip
foundations

vi) Well foundations 50 25 25

NOTES
1 The allowable bearing pressure shall be determined in accordance with good practice [6-2(7)] and [6-2(8)].
2 If any increase in bearing pressure has already been permitted for forces other than seismic forces, the total increase in allowable
bearing pressure when seismic force is also included shall not exceed the limits specified above.
3 Desirable minimum field values of N — If soils of smaller IV-values are met, compacting maybe adopted to achieve these values or
deep pile foundations going to stronger strata should be used.
4 The values of IV(corrected values) are at the founding level and the allowable bearing pressure shall be determined in accordance with
good practice [6-2(7)] and [6-2(8)].

Seismic 2bne Depth Below Ground N Values Remark


Level (in m)

(1) (2) (3) (4)

<5 15
III, IV and V
25 25 For values of depths between 5 m
and 10 m, linear interpolation is
H ~5 15 recommended
(for important
structures only) ~ 10 25
}

5 The piles should be designed for lateral loads neglecting lateral resistance of soil layers liable to liquefy.
6 Good practice [6-2(5)] and [6-2(9)] may also be referred,
7 Isolated RCC footing without tie beams, or unreinforced strip foundation shall not be permitted in soft soils with. A/ <10.

1,See good practice [6-2(5)].


2, See good practice [6-2(9)].

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 13


Table 4 Permissible Differential Settlements and Tilt (Angular Distortion) for Shallow Foundations in Soils

(Clause 7.1.3)
s] Type of Structure Isolated Foundations Raft Foundations

Sand and Hard Clay Plastic Clay Sand and Hard Clay Plastic Clay

/ A
- ~~ ~
Maximum Differential Angular Maximum Differential Maximum Differential Angular
settlement settlement distortion settlement settlement distortion settlement settlement distortion settlement settlement distortion
mm mm mm mm mm mm mm mm mm mm mm mm
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14)

i) For steel structure 50 .003 3L 1/300 50 .003 3L 1/300 75 .003 3L 1/300 100 .003 3L 1/300
ii) For reinforced concrete 50 .001 5L 1/666 75 .001 5L 1/666 75 .002 lL 1/500 100 .002 OL 1/500
structures
iii) For multistoreyed
buildings
a) RC or steel framed 60 ,002L 1/500 75 .002L 1/500 75 .002 5L 1/400 125 .003 3L 1/300
buildlngs with panel
walls
b) For load bearing
walls
1) IJH=2* 60 .000 2L 1/5 000 60 .000 2L 1/5000 4 Not likely to be encountered ~
2) L/H=7* 60 .000 4L 1/2 500 60 .000 4L 1/2500
iv) For water towers and 50 .001 5L 11666 75 .001 5L 11666 100 .002 5L 1/400 125 .002 5L 1/400
silos

NOTE — The vahres given in the table may tie ~en only as a guide and the permissible total settiementklifferent settlement and tilt (angular distortion) in each case should be decided as per
. .x
requirements of the designer.

L denotes the length of deflected part of walllraft or centre-to-centre distance between columns.
H denotes the height of wall from foundation footing.
* For intermediate ratios of UH, the vrdues can be interpolated.
7.1.4 Depth of Foundations load counteracting against swelling pressures also
provide satisfactory foundations.
7.1.4.1 The depth to which foundations should be
carried depends upon the following principal factors: 7.1.5 Foundation at Dl~erent Levels

a) The securing of adequate allowable capacity. 7.1.5.1 Where footings are adjacent to sloping
b) In the case of clayey soils, penetration below ground or where the bottoms of the footings of a
the zone where shrinkage and swelling due structure are at different levels or at levels different
to seasonal weather changes, and due to trees from those of the footings of adjoining structures,
and shrubs are likely to cause appreciable the depth of the footings shall be such that the
movements. difference in footing elevations shall be subject to
c) In fine sands and silts, penetration below the the following limitations:
zone in which trouble may be expected from a) When the ground surface slopes downward
frost. adjacent to a footing, the sloping surface shall
d) The maximum depth of scour, wherever not intersect a frustum of bearing material
relevant, should also be considered and the under the footing having sides which make
foundation should be located sufficiently an angle of 30° with the horizontal for soil
beIow this depth. and horizontal distance from the lower edge
e) Other factors such as ground movements and of the footing to the sloping surface shall be
heat transmitted from the building to the at least 600 mm for rock and 900 mm for soil
supporting ground may be important. (see Fig. 2).
b) In the case of footings in granular soil, a line
7.1.4.2 All foundations shall extend to a depth of at
drawn between the lower adjacent edges of
least 500 mm below natural ground level. On rock or
adjacent footings shall not have a steeper
such other weather resisting natural ground, removal
slope than one vertical to two horizontal (see
of the top soil maybe all that is required. In such cases,
Fig. 3).
the surface shall be cleaned and, if necessary, stepped
c) In case of footing of clayey soils a line drawn
or otherwise prepared so as to provide a suitable
between the lower adjacerit edge of the upper
bearing and thus prevent slipping or other unwanted
lmovements. footing and the upper adjacent edge of lower
footing shall not have a steeper slope than one
7.1.4.3 Where there is excavation, ditch pond, water vertical to two horizontal (see Fig. 4).
course, filled up ground or simikw condition adjoining
7.1.5.2 The requirement given in 7.1.5.1 shall not
or adjacent to the subsoil on which the structure is to
be erected and which is likely to impair the stability of apply under the following conditions:
structure, either the foundation of such structure shall a) Where adequate provision is made for the
be carried down to a depth beyond the detrimental lateral support (such as, with retaining walls)
influence of such conditions, or retaining walls or of the material supporting the higher footing.
similar works shall be constructed for the purpose of b) When the factor of safety of the foundation
shielding from their effects. soil against shearing is not less than four.
7.1.4.4 A foundation in any type of soil shall be below 7.1.6 Effect of Seasonal Weather Changes
the zone significantly weakened by root holes or
cavities produced by burrowing animals or works. The During periods of hot, dry weather a deficiency of
depth shall also be enough to prevent the rainwater water develops near the ground surface and in clay
scouring below the footings. soils, that is associated with a decrease of volume or
ground shrinkage and the development of cracks. The
7.1.4.5 Clay soils, like black cotton soils, are shrinkage of clay will be increased by drying effect
seasonally affected by drying, shrinkage and cracking produced by fast growing and water seeking trees. The
in dry and hot weather, and by swelling in the following range of influence depends on size and number of trees
wet weather to a depth which will vary according to and it increase during dry periods. In general, it is
the nature of the clay and the climatic condition of the desirable that there shall be a distance of at least 8 m
region. It is necessary in these soils, either to place the between such trees. Boiler installations, furnaces, kilns,
foundation bearing at such a depth where the effects underground cables and refrigeration installations and
of seasonal changes are not important or to make the other artificial sources of heat may also cause increased
foundation capable of eliminating the undesirable volume changes of clay by drying out the ground
effects due to relative movement by providing flexible beneath them, the drying out can be to a substantial
type of construction or rigid foundations. Adequate depth. Special precautions either in the form of

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 15


THESE SURFACES
SHOULD NOTINTERSECT

.!

FIG. 2 FOOTING
INSLOPING
GROUND

[ SLOPE OF JOINING ~LOWER


FOOTING
LINE NOT STEEPER
THAN TWO I+ORIZONTAL
TO ONE VERTICAL

FIG. 3 FOOTING
INGRANULAR
SOIL

/ SLOPE OF JOINING
LINE NOT STEEPER
\ LOWER
THAN TWO HORIZONTAL FOOTING
TO ONE VERTICAL

FIG. 4 FOOTING
IN CLAYEYSOIL

16 NATIONAL BUILDING CODE OF INDIA


insulation or otherwise should be taken. In periods of If the probable failure surface intersects a retaining
wet weather, clay soils swell and the cracks lend to wall or other revetment, the latter shall be made strong
close, the water deficiency developed in the previous enough to resist any unbalanced thrust. In case of doubt
dry periods may be partially replenished and a sub- as to the suitabilityy of the natural slopes or cuttings,
surface zone or zones deficient in water may persist the structure shall be kept well away from the top of
for many years. Leakage from water mains and the slopes, or the slopes shall be stabilized.
underground sewers may also result in large volume
Cuttings and excavations adjoining foundations reduce
changes. Therefore, special care must be taken to
stability and increase the likelihood of differential
prevent such leakages.
settlement. Their effect should be investigated not only
7.1.’7 Effect ofMass Movements of Ground in Unstable when they exist but also when there is possibility that
Areas they are made subsequently.

7.1.7.1 In certain areas mass movements of the ground Where a structure is to be placed on sloping ground,
are liable to occur from causes independent of the loads additional complications are introduced. The ground
applied by the foundations of structures. These include itself, particularly if of clay, may be subject to creep
mining subsidence, landslides on unstable slopes and or other forms of instability, which may be enhanced
creep on clay slopes. if the strata dip in the same direction as the ground
surface. If the slope of the ground is large, the overall
7.1.7.2 Mining subsidence
stability of the slope and substructure maybe affected.
In mining areas, subsidence of the ground beneath a These aspects should be carefully investigated.
building or any other structure is liable to occur. The
7.1.8 Precautions for Foundations on Inclined Strata
magnitude of the movement and its distribution over
the area are likely to be uncertain and attention shall, In the case of inclined strata, if they dip towards a
therefore, be directed to make the foundations and cutting of basement, it may be necessary to carry
structures sufficiently rigid and strong to withstand the foundation below the possible slip planes, land
probable worst loading condition. drainage also requires special consideration,
particularly on the uphill side of a structure to divert
7.1.7.3 Landslide prone areas
the natural flow of water away from the foundations.
The construction of structures on slopes which are
7.1.9 Strata of Varying Thickness
suspected of being unstable and are subject to landslip
shall be avoided. Strata of v~ing thickness, even at appreciable depth,
may increase differential settlement. Where necessary,
On sloping ground on clay soils, there is always a
calculations should be made of the estimated settlement
tendency for the upper layers of soil to move downhill,
from different thickness of strata and the structure
depending on type of soil, the angle of slope, climatic
should be designed accordingly. When there is large
conditions, etc. In some cases, the uneven surface of
change of thickness of soft strata, the stability of
the slope on a virgin ground will indicate that the area
foundation may be affected. Site investigations should,
is subject to small land slips and, therefore, if used for
therefore, ensure detection of significant variations in
foundation, will obviously necessitate special design
strata thickness.
consideration.
7.1.10 Luyers of Softer Material
Where there may be creep of the surface layer of the
soil, protection against creep may be obtained by Some soils and rocks have thin layers of softer material
following special design considerations. between layers of harder material, which may not be
detected unless thorough investigation is carried out.
On sloping sites, spread foundations shall be on a
The softer layers may ddergo marked changes in
horizontal bearing and stepped. At all changes of
properties if the loading on them is increased or
levels, they shall be lapped at the steps for a distance
decreased by the proposed construction or affected by
at least equal to the thickness of the foundation or
related changes in ground water conditions. These
twice the height of the step, whichever is greater. The
should be taken into accoun$.
steps shall not be of greater height than the thickness
of the foundation, unless special precautions are 7.1.11 Spacing Between Existing and New Foundation
taken.
The deeper the new foundation and the nearer to the
Cuttings, excavations or sloping ground near and below existing it is located, the greater the damage is likely
foundation level may increase the possibility of shear to be. The minimum horizontal spacing between
failure of the soil. The foundation shall be well beyond existing and new footings shall be equal to the width
the zone of such shear failure. of the wider one. While the adoption of such provision

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 17


shall help minimizing damage to adjacent foundation, The ground beam of reinforced concrete structurally
an analysis of bearing capacity and settlement shall be connected to reinforced brick work can also be used.
carried out to have an appreciation of the effect on the
7.2.5 Dimensions of Foundation
adj scent existing foundation.
The dimensions of the foundation in plan should be
7.1.12 Alterations During Construction
such as to support loads as given in good practice
a) Where during construction the soil or rock to [6-2( 11)]. The width of the footings shall be such that
which foundation is to transfer loads is found maximum stress in the concrete or masonry is within
not to be the type or in the condition assumed, the permissible limits. The width of wall foundation
the foundation shall be re-designed and (in mm) shall not be less than that given by:
constructed for the existing type or conditions
B = W+ 300
and the Authority notified.
b) Where a foundation bears on gravel, sand or where
silt and where the highest level of the ground B = Width at base in mm, and
water is or likely to be higher than an elevation
W = Width of supported wall in mm.
defined by bearing surface minus the width
of the footing, the bearing pressure shall be 7.2.6 In the base of foundations for masonry
altered in accordance with Note 4 in Table 3. foundation it is preferable to have the steps in multiples
c) Where the foundation has not been placed or of thickness of masonry unit.
located as indicated earlier or is damaged or 7.2.7 The plan dimensions of excavation for
bears on a soil whose properties may be foundations should be wide enough to ensure safe and ..—
adversely changed by climatic and efficient working with good practice [6-2( 12)].
construction conditions, the error shall be
corrected, the damaged portion repaired or the 7.2.8 Unreinforced foundation may be of concrete or
design capacity of the affected foundation masonry (stone or brick) provided that angular spread
recalculated to the satisfaction of the of load from the base of column/wall or bed plate to
Authority. the outer edge of the ground bearing is not more than
1 vertical to Y2 horizontal to masonry or 1 vertical to 1
d) Where a foundation is placed, and if the
horizontal for cement concrete and 1 vertical to 2/3
results of a load test so indicate, the design of
horizontal for lime concrete. The minimum thickness
the foundation shall be modified to ensure
of the foundation of the edge should not be less
structural stability of the same.
than 150 mm. In case the depth to transfer the load to
7.2 Pad or Spread and Strip Foundations the ground bearing is less than the permissible angle
of spread, the foundations should be reinforced.
7.2.1 In such type of foundations wherever the
resultant of the load deviates from the centre line by 7.2.9 If the bottom of a pier is to be belled so as to
more than 1/6 of its least dimension at the base of increase its load carrying capacity such bell should be
footing, it should be suitably reinforced. at least 300 mm thick at its edge. The sides should be
sloped at an angle of not less than 450 with the
7.2.2 For continuous wall foundations (plain or
horizontal, The least dimension should be 600 mm
reinforced) adequate reinforcement should be provided
(circular, square or rectangular). The design should
particularly at places where there is abrupt change in
allow for the vertical tilt of the pier by 1 percent of its
magnitude of load or variation in ground support.
height.
7.2.3 On sloping sites the foundation should have a
7.2.10 If the allowable bearing capacity is available
horizontal bearing and stepped and lapped at changes
only at a greater depth, tile foundation can be rested at
of levels for a distance at least equal to the thickness
a higher level for economic considerations and the
of foundation or twice the height of step whichever is
difference in level between the base of foundation and
greater. The steps should not be of greater height than
the depth at which the allowable bearing capacity
thickness of the foundations.
occurs can be filled up with either: (a) concrete of
7.2.4 Ground Beams allowable compressive strength not less than the
allowable bearing pressure, (b) in compressible fill
The foundation can also have the ground beam for
material, for example, sand, gravel, etc, in which case
transmitting the load. The ground beam carrying a load
the width of the fill should be more than the width of
bearing wall should be designed to act with the wall the foundation by an extent of dispersion of load from
forming a composite beam, when both are of reinforced
the base of the foundation on either side at the rate of
concrete and structurally connected by reinforcement.
2 vertical to 1 horizontal.

18 NATIONAL BUILDING CODE OF INDIA


7.2.11 The cement concrete foundation (plain or 7.3.1.2 In the case of raft, whether resting on soil
reinforced) should be designed in accordance with directly or on lean concrete, the cover to the
good practice [6-2(13)] and masonry foundation in reinforcement shall be as prescribed in Part 6
accordance with good practice [6-2(14)]. ‘Structural Design, Section 5 Concrete’ for the
applicable environment exposure condition.
7.2.12 Thickness of Footing
7.3.1.3 In case the structure supported by the raft
The thickness of different types of footings, if not
consists of several parts with varying loads and heights,
designed according to 7.1, shouldbe as given in
it is advisable to provide separation joints between
Table 5.
these parts. Joints shall also be provided wherever there
7.2.13 LandSlipArea is a change in the direction of the raft.
Ona sloping site, spread foundation shall beona 7.3.1.4 Foundations subject to heavy vibratory loads
horizontal bearing and stepped. At all changes of levels, should preferably be isolated. ,
they shall be lapped at the steps for a distance at least
equal to the thickness of the foundation or twice the 7.3.1.5 The minimum depth of foundation shall
height of the step, whichever is greater. The steps shall generally be not less than 1 m.
not be of greater height than the thickness of the 7.3.1.5 Dimensional parameters
foundation unless special precautions are taken. On
sloping ground on clay soils, there is always a tendency The size and shape of the foundation adopted affect
for the upper layers of soil to move downhill, the magnitude of subgrade modulus and long-term
depending on type of soil, the angle of slope, climatic deformation of the supporting soil and this, in turn,
conditions, etc. Special precautions are necessary to influences the distribution of contact pressure. This
avoid such a failure. aspect needs to be taken into consideration in the
anal ysis.
7.2.14 In the foundations, the cover to the reinforcement
shall be as prescribed in Part 6 ‘Structural Design, 7.3.1.7 Eccentric@ of loading
Section 5 Concrete for the Applicable Environment A raft generally occupies the entire area of the building
Exposure Condkion’. and often it is not feasible and rather uneconomical to
7.2.15 For detailed information regarding preparation proportion it coinciding the centroid of the raft with
of ground work, reference may be made to good the line of action of the resultant force. In such cases,
practice [6-2(15)]. the effect of the eccentricity on contact pressure
distribution shall be taken into consideration.
7.3 Raft Foundations
7.3.1.8 Properties of supporting soil
7.3.1 Design Considerations
Distribution of contact pressure underneath a raft is
Design provisions given in 7.1 shall generally apply. affected by the physical characteristics of the soil
7.3.1.1 The structural design of reinforced concrete supporting it. Consideration must be given to the
rafts shall conform to Part 6 ‘Structural Design, increased contact pressure developed along the edges
Section 5 Concrete’. of foundation on cohesive soils and the opposite effect

Table 5 Thickness of Footings


(Clause 7.2.12) ,,

S1No. Type of Footings Thickness of Footings, &fin Remarks


./”
(1) (2) (3) (4)

i) Masonry a) 250 mm Select the greater of Oretwo values


b) Twice the maximum projection from tke face of
the wall
ii) Plain concrete
For normal structures a) 200 mm
b) Twice tke maximum offset in a stepped footing For footings resting on top of the pile
c) 300 mm
For footings resting on soil
For lightly loaded structures a) 150 mm Resting on soil
b) 200 mm Resting on pile
ii) Reinforced concrete a) 150mm Resting on soil
b) 300 mm Resting on pile

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 19


r

on granular soils. Long-term consolidation of deep soil static and dynamic penetration tests, pressure
layers shall be taken into account in the analysis. This meter tests etc); and
may necessitate evaluation of contact pressure f) A review of the performance of similar
distribution both immediately after construction and structure, if any, in the locality.
after completion of the consolidation process. The
design must be based on the worst conditions. 7.3.3 Choice of Ra# Type

7.3.1.9 Rigidity of foundations 7.3.3.1 For fairly small and uniform column spacing
and when the supporting soil is not too compressible a
Rigidity of the foundation tends to iron out uneven flat concrete slab having uniform thickness throughout
deformation and thereby modifies the contact pressure (a true mat) is most suitable (see Fig. 5A).
distribution. High order of rigidity is characterized
by long moments and relatively small, uniform 7.3.3.2 A slab maybe thickened under heavy loaded
settlements. A rigid foundation may also generate high columns to provide adequate strength for sheai and
secondary stresses in structural members. The effect negative moment. Pedestals may also be provided in
of rigidity shall be taken into account in analysis. such cases (see Fig. 5B).

7.3.1.10 Rigidity of the superstructure 7.3.3.3 A slab and beam type of raft is likely to be
more economical for large column spacing and unequal
Free response of the foundations to soil deformation column loads particularly when the supporting soil is
is restricted by the rigidity of the superstructure. In the very compressive (see Fig. 5C and 5D).
extreme case, a stiff structure may force a flexible
foundation to behave as rigid. This aspect shall be 7.3.3.4 For very heavy structures, provision of cellular
considered to evaluate the validity of the contact raft or rigid frames consisting of slabs and basement
pressure distribution. walls may be considered.

7.3.1.11 Modulus of elasticity and modulus of 7.3.4 Methods of Armlysis


subgrade reaction The essential task in the analysis of a raft foundation
Annex A enumerates the methods of determination of is the determination of the distribution of contact
modulus of elasticity (E,). The modulus of subgrade pressure underneath the raft which is a complex
reaction (k) may be determined in accordance with function of the rigidity of the superstructure, the
Annex B. supporting soil and the raft itself, and cannot be
determined with exactitude, except in very simple
7.3.2 Necessary Information cases. This necessitates a number of simplifying
The following information is necessary for a assumptions to make the problem amenable to analysis.
satisfactory design and construction of a raft Once the distribution of contact pressure is determined,
foundation: design bending moments and shears can be computed
based on statics. The methods of analysis suggested
a) Site plan showing the location of the proposed are distinguished by the assumptions involved. Choice
as well as the neighboring structures; of a particular method should be governed by the
b) Plan and cross-sections of building showing validity of the assumptions in the particular case.
different floor levels, shafts and openings, etc,
7.3.4.1 Rigid foundation (conventional method)
layout of loading bearing walls, columns,
shear walls, etc; This method is based on the assumption of linear
c) Loading conditions, preferably shown on a distribution of contact pressure. The basic assumptions
schematic plan indicating combination of of this method are:
design loads transmitted to the foundation; a) the foundations rigid relative to the supporting
d) Information relating to geological history of soil and the compressible soil layer is
the area, seisrnicity of their area, hydrological relatively shallow; and
information indicating ground water b) the contact pressure variation is assumed as
conditions and its seasonal variations, etc; planar, such that the centroid of the contact
e) Geotechnical information giving subsurface pressure coincides with the line of action of
profile with stratification details, engineering the resultant force of all loads acting on the
properties of the founding strata (namely, foundation.
index properties, effective shear parameters
determined under appropriate drainage This method may be used when either of the following
conditions, compressibility characteristics, conditions is satisfied:
swelling properties, results of field tests like a) The structure behaves as rigid (due to the

20 NATIONAL BUILDING CODE OF INDIA


o 0 ❑ ❑ d b o ❑ ❑ d

❑ o ❑ o ❑ o ❑ o ❑ ❑

.—. — .—-— _—-— -—- —-


A n ❑ 0 0
: 77 A13
“
0 0 ❑
❑ 7 B

@ 0 ❑ ❑ 9 s 0 ❑ 0 m

) SECTION’B6
SECTION AA

5B FLAT PLATE THICKENED


5A FLAT PLATE UNDER COLUMNS

in ❑ o 0 d b a o 0 d

❑ lnrlil ❑ o 0 ❑
❑
-—-—- —-—-
c
r T c D 0 0

0
0

0
0

a
07

Q
D

In o 0 ❑ d D

SECTION ~C SECTION DD

5C TWO-WAY BEAM 5D FIAT P+TE WITH


AND SLAB PEDESTALS

FIG. 5 COMMON TYPES OF RAFT FOUNDATION ,U

combined action of the superstructure and the In the case of uniform conditions when the variations in
foundation) with relative stiffness factor adjacent column loads and column spacings do not
K> 0.5 (for evaluation o~Ksee Annex C); and exceed 20 percent of the higher value, the raft may be
b) The column spacing is less than 1.75/a (see divided into perpendicular strips of widths equal to the
Annex C). distance between midspans and each strip may be
analysed as an independent beam with known column
The raft is analysed as a whole in each of the two loads and known contact pressures. Such beams will
perpendicular directions. The contact pressure not normally satisfy statics due to shear transfer between
distribution is determined by the procedure outlined adjacent strips and design may be based on suitable
in Annex D. Further analysis is also based on statics. moment coefficients, or by moment distribution.

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 21


NOTE — On soft soils, for example, normally consolidated application of pile foundations is in practice over many
clays, peat, muck, organic silts, etc, the assumptions involved
decades. Broadly, piles transfer axial loads either
in the conventional method are commonly justified.
substantially by friction along their shafts and/or
7.3.4.2 Flexible foundations substantially by the end bearing. Construction of a pile
foundation requires a careful choice of piling system,
a) Simplified method — In this method, it is
depending upon the subsoil conditions, the load
assumed that the subgrade consists of an
characteristics of a structure and the limitation of total
infinite array of individual elastic springs each
settlement, differential settlements and any other
of which is not affected by others. The spring
special requirement of a project.
constant is equal to the modulus of subgrade
reaction (k). The contact pressure at any
8.1 Material
point under the raft is, therefore, linearly
proportional to the settlement at the point. 8.1.1 Concrete
Contact pressure may be determined as given The minimum grade of concrete to be used shall not
in Annex E. This method may be used when
be less than that arrived at in accordance with Part 6
all the following conditions are satisfied: ‘Structural Design, Section 5 Concrete’.
1) The structure (combined action of
superstructure and raft) may be 8.1.1.1 For bored and driven cast-in-situ concrete
considered as flexible (relative stiffness piles including under- reamed piles
factor K> 0.5, see Annex C). The minimum cement content shall be 400 kg/m3 in
2) Variation in adjacent column load does all conditions. For piles up to 6 m, minimum cement
not exceed 20 percent of the higher value. content of 350 kg/m3 without provision for underwater ---

b) General method — For the general case of concreting may be used under favorable non-
a flexible foundation not satisfying the aggressive subsoil condition and where concrete of
requirements of (a), the method based on higher strength is not needed structurally or due to
closed form solution of elastic plate theory aggressive site conditions. For concreting in aggressive
may be used. This method is based on the surroundings due to presence of sulphates, etc the
theory of plates on winkler foundation which provisions given in Part 6 ‘Structural Design, Section
takes into account the restraint on deflection 5 Concrete’ shall be followed.
of a point provided by continuity of the
8.L2 Steel Reinforcement
foundation in orthogonal foundation. The
distribution of deflection and contact pressure Steel reinforcement shall conform to any one of the
on the raft due to a column load is determined types of steel specified in Part 6 ‘Structural Design,
by the plate theory. Since the effect of a Section 5 Concrete’.
column load on an elastic foundation is
8.2 Design Considerations
damped out rapidly, it is possible to determine
the total effect at a point of all column loads Pile foundation shall be designed in such a way that
within the zone of influence by the method the load from the structure it supports can be
of superimposition. The computation of effect transmitted to the soil without causing any soil failure
at any point may be restricted to columns of and without causing such settlement, differential or
two adjoining bays in all directions. The total under permanenth-ansient loading as may result
procedure is outlined in Annex F. in structural darnage andhr functional distress. The
pile shaft should have adequate structural capacity to
7.4 Ring Foundations withstand all loads (vertical, axial or otherwise) and
moments which are to be tmnsmitted to the subsoil.
For provisions regarding ring foundations good
practice [6-2( 16)] shall be referred to. NOTE— When working near existing structures, care shall be
taken to avoid any damage to structures.
8 DRIVEN/BORED CAST ZN-SZTU CONCRETE
8.2.1 Soil Resistance
PILES
The bearing capacity of a pile is dependent on the
8.0 General
properties of the soil in which it is embedded. Axial
Piles find application in foundations to transfer load load from a pile is normally transmitted to the soil
from a structure to competent sub-surface strata having through skin friction along the shaft and end bearing
adequate load bearing capacity. The load transfer at its tip. A horizontal load on a vertical pile is
mechanism from a pile to the surrounding ground is transmitted to the subsoil primarily by horizontal
complicated and is yet to be fully understood, although subgrade reaction generated in the upper part of the

22 NATIONAL BUILDING CODE OF INDIA


shaft. A single pile is normally designed to carry load with reasonable accuracy from test loading as per good
along its axis. The transverse load bearing capacity of practice [6-2( 18)]. The load test on a pile shall not be
a single pile depends on the soil reaction developed carried out earlier than four weeks from the time of
and the structural capacity of the shaft under bending. casting the pile.
In case the horizontal loads are of higher magnitude, it
8.2.1.5 Non-destructive testing
is essential to investigate the phenomena using
principles of horizontal subsoil reaction adopting For quality assurance of concrete piles, non-destructive
appropriate values for horizontal modulus of the soil. integrity test may be carried out prior to laying of beard
Alternatively, piles may be installed in rake. The caps, in accordance with good practice [6-2(19)1.
feasibility of constructing bored piles in rake under a
8.2.2 Negative Skin Friction or Dragdown Force
given subsoil condition should, however, be examined
critically. When a soil siratum, through which a pile shaft has
penetrated into an underlying hard stratum, compresses
8.2.1.1 The ultimate bearing capacity of a pile may
as a result of either its being unconsolidated or its being
be estimated approximately by means of a static
under a newly placed fill or as a result of re-moulding
formula on the basis of soil test results or by test during driving of the pile, a dragdown force is
loading. The settlement of pile obtained at safe load/
generated along the pile shaft up to a point in depth
working load from load test results on a single pile
where the surrounding soil does not move downwards
shall not be directly used in forecasting the settlement
relative to the pile shaft. Recognition of the existence
of a structure unless experience from similar
of such a phenomenon shall be made and a suitable
foundations on its settlement behaviour is available.
reduction shall be made to the allowable load, where
The average settlement may be assessed on the basis
appropriate.
of subsoil data and loading details of the structure as a
whole using the principle of soil mechanics. 8.2.3 Structural Capacity

8.2.1.2 Static formula The piles shall have the necessary structural strength
to transmit the loads imposed on them ultimately to
By using static formula, the estimated value of the
the soil.
ultimate bearing capacity of a typical pile is obtained,
the accuracy being dependent on the reliability of the 8.2.3.1 Axial capacity
formula and the reliability of the soil properties for
Where a pile is fully embedded in the soil (having an
various strata available. The soil properties to be
undrained shear strength not less than 10 kN/m2) its
adopted in such a formula maybe assigned from results
axial carrying capacity is not limited by its strength as
of laboratory tests and field tests as per good practice a long column. Where piles are installed through very
[6-2( 1)]. Two separate static formulae commonly weak soils (having an undrained shear strength less
applicable for cohesive and non-cohesive soils are
than 10 kN/m2), special consideration shall be given
indicated in Annex G, to serve only as a guide. Other
to determine whether the shaft would behave as a long
alternative formulae may be applicable, depending on
column or not; if necessary suitable reductions shall
the subsoil characteristics and method of installation
be made in its structural strength considering the
of piles.
buckling phenomenon.
8.2.1.3 Dynamic formula
When the finished pile projects above ground level
For driven piles in non-cohesive soils, such as gravels, and is not secured against buckling by adequate
coarse sand and other similar deposits, an approximate bracing, the effective length will be governed by the
value of the bearing capacity may be determined by a fixity conditions imposed on it by the structure it
dynamic pile formula as per good practice [6-2(17)]. supports and by the nature of the soil into which it is
Dynamic formulae are not directly applicable to installed. The depth below the ground surface to the
cohesive soil deposits, such as saturated slits and clays, lower point of contraflexure varies with the type of
as the resistance to impact of the toe of the casing will soil. In good soil the lower point of contraflexure may
be exaggerated by their low permeability, while the be taken at a depth of 1 m below ground surface
frictional resistance on the sides is reduced by subject to a minimum of three times the diameter of
lubrication. If as a result of test loadings on a given the shaft. In weak soil (undrained shear strength less
area a suitable coefficient can be applied to a dynamic than 10 kN/m2) such as soft clay and soft slit, this point
formula, the results may then be considered as may be taken at about half the depth of penetration
reasonable. into such stratum but not more than 3 m or 10 times
the diameter of the shaft, whichever is less. A stratum
8.2.1.4 Load test results
of liquid mud should be treated as if it was water.
The ultimate load capacity of a single pile is determined The degree of fixity of the position and inclination

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 23


of the pile top and the restraint provided by any be determined graphically or by analytical methods.
bracing shall be estimated following accepted Where necessary, due consideration should be given
structural principles. to secondary bending induced as a result of the pile
cap movement, particularly when the cap is rigid.
8.2.3.2 Uplifi capaci~
Free-standing raker piles are subjected to bending
Total uplift capacity of pile will be the sum of the moments due to their own weight, or external forces
frictional resistance and weight of the pile (buoyant from other causes. Raker piles embedded in loose
or total as relevant). The uplift capacity from the static fill or consolidating deposit may become laterally
formula (Annex G) can be approximately estimated loaded owing to the settlement of the surrounding
by ignoring end bearing but adding weight of pile soil. In consolidating clay special precautions, like
(buoyant or total as relevant). The safe uplift provision of permanent casing, should be taken for
capacity can be obtained by applying a factor of raker piles.’
safety 3. However, more reliance should be given to
8.2.4 Spacing of Piles
that obtained from test loading as per good practice
[6-2(18)]. The centre to centre spacing of a pile is considered
from two aspects as follows:
8.2.3.3 Lateral load cauaci~
. .
a) Practical aspects of installing the piles; and
A pile may be subjected to transverse forces for a
b) The nature of the load transfer to the soil and
number of causes, such as wind, earthquake, water
possible reduction in bearing capacity of a
current, earth pressure, effect of moving vehicles or
group of piles thereby.
ships, plant and equipment, etc. The lateral load ..-
carrying capacity of a single pile depends not only on 8.2.4.1 In the case of piles founded on a very hard
the horizontal subgrade modulus of the surrounding stratum and derivhtg their capacity mainly from end
soil but also on the structural strength of the pile shaft bearing, the spacing will be governed by the
against bending consequent upon the application of a competency of the end bearing strata. The minimum
lateral load. While considering lateral load on piles, spacing in such cases shall be 2.5 times the diameter
the effect of other co-existent loads, including the axial of the shaft. In case of piles resting on rock, a spacing
load on the pile, should be taken into consideration of two times the diameter maybe adopted.
for checking the structural capacity of the shaft. A
8.2.4.2 Piles deriving their bearing capacity mainly
method for the determination of the depth of fixity of
from friction shall be sufficiently apart to ensure that
piles for driven cast in-situ and depth of fixity, lateral
the zones of soil from which the piles derive their
deflection and maximum moment for driven precast,
support do not overlap to such an extent that their
bored cast-in-situ and bored precast piles required for
bearing values are reduced. Generally, the spacing in
design is given in Annex H. Other accepted methods,
such cases shall not be less than three times the
such as the method of Reese and Matlock or finite
diameter of the shaft.
element analysis using linear/non-linear springs to
represent the resistance of soil. A pile in a group of 8.2.4.3 In the case of loose sand or filling, closer
three or more piles connected by a rigid cap shall be spacing than in dense sand may be possible, in driven
designed considering as ‘fixed head condition’. In caps piles since displacement during the piling may be
of single piles interconnected by ground beams in two absorbed by vertical and horizontal compaction of the
directions and for two piles by ground beams in a line strata. The minimum sp?cing in such strata may be
transverse to the common axis of the piles is also to be two times the diameter of the shaft.
considered as ‘fixed head condition’. In all other
NOTE — In the case of piles of non-circular cross-section, the
conditions the pile shall be designed by treating it ‘free diameter of the circumscrib~ circle shall be adopted.
head condition’.
8.2.5 Pile Grouvim?
.-
NOTE — Because of limited information on horizontal modulus
of soil, and requirements in the theoretical analysis, it is In order to determine the bearing capacity of a group
suggested that the adequacy of a design should be checked by of piles, a number of efficiency equations are in use.
an actual f[eld load test.
However, it is very dlftlcult to establish the accuracy
8.2.3.4 Raker piles of these efficiency equations, as the behaviour of pile
group is dependent on many complex factors. R is
Raker piles are normally provided where vertical piles
desirable to consider each case separately on its own
cannot resist the required applied horizontal forces. In
merits.
the preliminary design, the load on a raker pile is
generally considered to be axial. The distribution of 8.2.5.1 The bearing capacity of a pile group may be
load between raker and vertical piles in a group may either of the following:

24 NATIONAL BUILDING CODE OF INDIA


F-”

a) Equal to the bearing capacity of individual 8.2.6 Factor of Safety


piles multiplied by the number of piles in
8.2.6.1 The factor of safety should be judiciously
group; or
chosen after considering the following:
b) It maybe less.
a) The reliability of the value of the ultimate
The former holds true in the case of friction piles,
bearing capacity of a pile,
cast or driven into progressively stiffer materials or
b) The type of superstructure and the type of
in end-bearing piles. In friction piles in soft and clayey
loading, and
soils, it is normally smaller. For driven piles in loose
sandy soils, the group value may be higher due to the c) Allowable total/differential settlement of the
effect of compaction. In such a case, a load test should structure.
be made on a pile from the group after all the piles 8.2.6.2 Whe’n the ultimate bearing capacity is
have been installed. The group capacity may then be compound from either static formula or dynamic
decided by taking into account the interference formula, the factor of safety would depend on the
effects. This would be done by multiplying the total reliability of the formulae, depending on a particular
capacity of a pile group with the group efficiency site and locality and the reliability of the subsoil
factor. parameters employed in such computation. The
8.2.5.2 In the case of piles deriving their support minimum factor of safety on static formula shall be
mainly from friction and connected by a rigid pile cap, 2.5. The final solution of a factor of safety shall take
the group may be visualized to transmit load to the into consideration the load settlement characteristics
soil, as if from a column of soil, enclosed by the piles. of the structure as a whole on a given site.
The ultimate capacity of the group maybe computed 8.2.6.3 The factor of safety for assessing the safe load
following this concept, taking into account the on piles from load test data should be increased in
frictional capacity along the perimeter of the column unfavorable conditions where:
of soil as above and the end bearing of the said column
using the accepted principles of soil mechanics. a) settlement is to be limited or unequal
settlement avoided as in the case of accurately
8.2.5.3 When the cap of the pile group is cast directly aligned machinery or a superstructure with
on a reasonably firm stratum which supports the piles, fragile finishings;
it may contribute to the bearing capacity of the group.
b) large impact or vibrating loads are expected;
This additional capacity along with the individual
capacity of the piles multiplied by the number of piles c) the properties of the soil maybe expected to
in the group shall not be more than the capacity worked deteriorate with time; and
out as per 8.2.5.2. d) the live load on a structure carried by friction
piles is a considerable portion of the total and
8.2.5.4 When a moment is applied on the pile group
approximates to the dead load in its duration.
either from the superstructure or as a consequence
of unavoidable inaccuracies of installation, the 8.2.7 Transient Loading
adequacy of the pile group in resisting the applied
The maximum permissible increase over the safe load
moment should be checked. In the case of a single
of a pile as arising out of wind loading is 25 percent.
pile subjected to moments due to lateral forces or
In the case of loads and moments arising out of
eccentric loading, beams may be provided to restrain
earthquake effects, the increase of safeload shall be as
the pile caps effectively from lateral or rotational
given in Table 3.
movement.
8.2.8 Overloading
8.2.5.5 In the case of a structure supported on a single
pile/group of piles, resulting in large variation in the When a pile in a group, designed for a certain safe
number of piles from column to column, it is likely, load is found, during or after execution, to fall just
depending on the type of subsoil supporting the piles, short of the load required to be carried by it, an overload
to result in a high order of differential settlement. Such of up to 10 percent of the pile capacity maybe allowed
high order of differential settlement may be either on each pile. The total overloading on the group should
catered for in the structural design or it may be suitably not be more than 10 percent of the capacity of the group
reduced by judicious choice of variations in the actual nor more than 40 percent of the rdlowable load on a
pile loadings. For example, a single pile cap may be single pile.
loaded to a level higher than that of a pile in a group in
8.2.9 Reinforcement
order to achieve reduced differential settlement
between the adjacent pile caps supported on different 8.2.9.1 The design of the reinforcing cage varies
number of piles. depending upon the driving and installation conditions,

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 25


the nature of the subsoil and the nature of load to be the entire action of any pile of diameter D whose centre
transmitted by the shaft-axial, or otherwise. The is located D/2 or more outside the section shall be
minimum area of longitudinal reinforcement (any type assumed as producing no shear on the section. For
or grade) within the pile shaft shall be 0.4 percent of intermediate positions of the pile centre, the portion
the sectional area calculated on the basis of the outside of the pile reaction to be assumed as producing shear
area of the casing of the shaft. on the section shall be based on straight-line
interpolation between full value at D/2 outside the
8.2.9.2 The curtailment of reinforcement along the
section and zero value at D/2 inside the section. Further,
depth of the pile, in general, depends on the type of
design may be carried out as specified in Part 6
loading and subsoil strata. In the case of piles subjected
‘Structural Design, Section 5 Concrete’.
to compressive load only, the designed quantity of
reinforcement may be curtailed at an appropriate level 8.2.10.2 The pile cap shall be deep enough to allow
as per the design requirements. For piles subjected to for necessary anchorage of the column and pile
uplift load, lateral load and moments, separately or with reinforcement and the minimum thickness shall
compressive loads, it may be necessary to provide be 300 mm.
reinforcement for the full depth of pile. In soft clays
8.2.10.3 The pile cap should normally be rigid enough,
or loose sands, or where there is likelihood of danger
so that the imposed load could be distributed on the
to green concrete due to driving of adjacent piles, the
piles in a group equitably.
reinforcement should be provided up to the full pile
depth, regardless of whether or not it is required from 8.2.10.4 In the case of a large cap, where differential
uplift and lateral load considerations. However, in all settlement may be imposed between piles under the
..-
cases, the minimum reinforcement specified in 8.2.9.1 same cap, due consideration should be given to the
should be provided in the full length of the pile. consequential moment.

Piles shall always be reinforced with a minimum 8.2.10.5 The clear overhang of the pile cap beyond
amount of reinforcement as dowels, keeping the the outer most pile in the group shall normally
minimum bond length into the pile shaft and with be 100 mm to 150 mm, depending upon the pile
adequate projection into the pile cap. size.
NOTE — In some cases the cage may lift at bottom or at the top 8.2.10.6 The cap is generally cast over a 75 mm thick
during withdrawal of casing. This can be minimized by making
levelling course of concrete. The clear cover for the
the reinforcement ‘U’ shaped at the bottom and up to well
secured joints, Also the lifting 5 percent of the length should be main reinforcement in the cap slab shall not be less
considered not to affect the quality of pile. than 60 mm.

8.2.9.3 Clear cover to all main reinforcements in pile 8.2.10.7 The pile should project 50 mm into the cap
shaft shall be not less than 50 mm. The laterals of a concrete.
reinforcing cage may be in the form of links or spirals.
8.2.11 Grade Beams
The diameter and spacing of the same are so chosen as
to impart adequate rigidity to the reinforcing cage 8.2.11.1 The grade beams supporting the walls shall
during its handling and installation. The minimum be designed taking due account of arching effect due
diameter of the links or spirals shall be 6 mm and the to masonry above the beam. The beam with masonry
spacing of the links or spirals shall be not less due to composite action behaves as a deep beam.
than 150 mm.
For the design of beams, a maximum bending moment
8.2.10 Design of Pile Cap of wl 2
~, where w is uniformly distributed load per
8.2.10.1 The pile caps may be designed considering metre run (worked out @ considering a maximum
that the reaction from any pile is concentrated at the height of two storeys in structures with load bearing
centre of the pile. The critical section for shear in walls and one storey in framed structures) and 1is the
diagonal tension is taken at a distance equal to half the effective span in metres, will be taken if the beams are
effective depth of cap from the face of column/pedestal supported during construction till the masonry above
or wall. For bending moment and shear for bond, the it gains strength. The value of bending moment shall
critical section is taken at the face of column/pedestal
or wall for cap supporting a concrete colwim, pedestal be increased to —,
~~ if the beams are not supported.
or wall; halfway between the centre line and the edge For considering c;rnposite action, the minimum height
of the wall for caps under masonry walls and half-way of wall shall be 0.6 times the beam span. The brick
between the face of the column or pedestal and the strength should not be less than 3 N/mmz. For
edge of the gusseted base for caps under gusseted bases. concentrated and other loads which come directly over
In computing the external shear or the critical section, the beam, full bending moment should be considered.

26 NATIONAL BUILDING CODE OF INDIA


8.2.11.2 The minimum overall depth of grade beams Number of Location of Point of Bending
shall be 150 mm. The reinforcement at the bottom Points of Pick Suppo~ from in Moment to be
should be kept continuous and an equal amount may up Terms of Length of Allowed for
be provided at top to a distance of a quarter span both Pile for Minimum Design
ways from pile centres. The longitudinal reinforcement Moments
both at top and bottom should not be less than three
WL
bars of 10 mm diameter mild steel (or equivalent One 0.293 L
23.3
deformed steel) and stirrups of 6 mm diameter bars
should be spaced at a minimum of 300 mm spacing. WL
Two 0.207 L
8.2.11.3 In expansive soils, the grade beams shall be 46.6
kept a minimum of 80 mm clear off the ground. In other Three 0.145 L, the middle WL
soils, beams may rest on ground over a Ievelling point will beat the
centre %
concrete course of about 80 mm (see Fig. 6).

8.2.11.4 In the case of exterior beams over piles in where


expensive soils, an edge projection of 75 mm thickness
W = Mass of pile in kg, and
and extending 80 mm into ground (see Fig. 6) shall be
L = Length in metres.
provided on the outer side of the beam.
During hoisting the pile will be suspended at one point
8.3 For detailed information on driven/bored cast
near the head and the bending moment will be the least
in-situ concrete piles regarding control of piling,
when it is pulled in a distance of 0.293 L, and the value
installation, defective pile and recording of data,
of bending moment will be:
reference may be made to good practice [6-2(17)].

9 DRIVEN PRECAST CONCRETE PILES WL


23.3
9.1 Provisions of 8 except 8.2.9 shall generally apply.
9.3 Reinforcement
9.2 Design of Piles
9.3.1 The longitudinal reinforcement shall be provided
9.2.1 The design of pile section shall be such as to in precast reinforced concrete piles for the entire length.
ensure the strength and soundness of the pile against All the main longitudinal bars shall be of the same
lifting from the casting bed, transporting, handling, length with lap welded at joints and should fit tightly
driving stresses without damage. into the pile shoe if there is one. Shorter rods to resist
local bending moments may be added, but the same
9.2.2 Any shape having radial symmetry will be
should be carefully detailed to avoid any sudden
satisfactory for precast piles. The most common cross-
discontinuity of the steel which may lead to cracks
sections used are square and octagonal or circular.
during heavy driving. The area of the main longitudinal
9.2.3 Where exceptionally long lengths of piles are reinforcement shall not be less than the following
required, hollow sections may advantageously be used. percentages of the cross-sectional area of the piles:
If the final conditions require a larger cross-sectional
a) For piles with length less than 30 times the
area, the hollow sections may be filled with concrete
least width — 1.25 percent
after driving in position.
b) For piles with length 30 to 40 times the least
9.2.4 Excessive whippiness in handling precast pile width — 1.5 percent, and
may generally be avoided by limiting the length of pile c) For piles with len@h greater than 40 times
to a maximum of 50 times the least width. the least width — 2 percent.

9.2.5 L@tg and Handling Stresses 9.3.2 The lateral reinforcement is of particular
importance in resisting the driving stresses induced in
Stresses induced by bending in the cross-section of a
the piles and should be in the form of hoops or links
precast pile during lifting and handling may be
and of diameter not less than 6 mm. The volume of
estimated just as for any reinforced concrete section
lateral reinforcement shall not be less than the
in accordance with relevant provisions of good practice
following:
[6-2( 13)]. The calculations with regard to moments
depending on the method of support during handling a) At each end of the pile for a distance of about
will be as given below. Excessive whippiness in handling 3 times the least width — not less than 0.6
precast pile may generally be avoided by limiting the percent of the gross volume of that. part of
length of pile to a maximum of 50 times the least width. the pile; and

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 27


WfQTH OF WALL WIDTH OF WALL

L 50 mm THICK CONCRETE
SLAB OR BRICK ON EDGE
k+
[ 50 mm THICK CONCRETE
SLAB OR BRICK ON EDGE

INTERIOR BEAM EXTERIOR BEAM

6A BEAMS IN EXPANSIVE SOILS

- WIDTH OF WALL d .
.
///\\\ ..J ., . “:.. % ... ,,*,, ,., .:.,, //7?s MAY BE ELIMINATED
IN CASE OF VERTICAL

‘;;=: ,,, .,. > cm’


:,L.:: : ,,:,.:’” ‘$ “’.*,.,...:’ :“;. ik” ...””: ‘,’.
,, ,,. ‘, ‘,.{. +.”:,:; .;!;,,:’;::,; .:,:. ,; . ,; .::*,,,
,. #,’.... ,,...,, ,. .’, ,,,,.,~~ ,.,,,.,... ~,.

LEVELLING COURSE 1

BEAMS IN NON - EXPANSIVE SOILS

All dimensions in millimetres.

FIG. 6 TYPICAL SECTIONS OF GRADEBEAMS

b) In the body of the pile — not less than soils likely to damage the concrete at the tip of the
0.2 percent of the gross volume of the pile. pile. The shoe can be of steel or cast iron. In uniform
clay or sand, the shoe may be omitted.
The spacing shall be such as to permit free flow of
concrete around it. The transition between the close Where jetting is necessary for concrete piles, a jet tube
spacing of lateral reinforcement near the ends and the may be cast into the pilp, the tube, being connected to
maximum spacing shall be gradually over a length of the pile shoe which, is provided with jet holes.
3 times the least width of the pile. Generally, a central jet is inadvisable, as it is liable to
.
become choked. At least,~o jet holes will be necessary
9.3.3 The cover of concrete overall the reinforcement,
on opposite sides of the shoe, four holes giving best
including ties, should not be less than 40 mm. But
results. Alternatively, two or more jet pipes may be
where the piles are exposed to sea-water or water
attached to the sides of the pile.
having other corrosive content, the cover should be
nowhere less than 50 mm. Cover should be measured 9.4 For detailed information regarding casting and
clear from the main or longitudinal reinforcement. curing, storing and handling, control of pile driving
and recording of data, reference maybe made to good
NOTE — Where concrete of the pile is liable to be exposed to
the attack of sulphates aad chlorides present in the ground water, practice [6-2(20)].
the piles may be coated with a suitable material.
10 BORED PRECAST CONCRETE PILES
9.3.4 Piles should be provided with flat or pointed co-
axial shoes if they are driven into or through ground, 10.1 Provisions of 9 except 9.3 shall generally apply.
such as rock, coarse gravel, clay with cobbles and other 10.2 For grouting the space around the pile, the precast

28 NATIONALBUILDING CODE OF INDIA


pile should be provided with a central ducthle or of bore hole stand by itself without needing any
suitable jet holes to pump the grouting material. The stabilization by using drilling mud or otherwise, the
bottom end of the pile shall have proper arrangements maximum number of bulbs in under-reamed piles
for flushing/cleaning for grouting. should be restricted to two. In strata, for example, clayey
sand, silty sand and sandy silt with high water table
10.3 Reinforcement where bore hole needs stabilization by using drilling
The longitudinal reinforcement shall be provided in mud, under-reamed piles with more than one bulb shall
for the entire length preferably of high yield strength not be used. In loose to medium pervious strata such
to withstand the handling stresses to the extent to meet as clayey sand, silty sand and sandy silt strata,
requirement as given in 9.2.5. All the main longitudinal compaction under-reamed piles can be used as the
bars shall be of the same length. The area of the main process of compaction, increases the load carrying
longitudinal reinforcement of any type and grade shall capacity of piles. From practical considerations,
not be less than 0.4 percent of the cross-section area under-reamed piles of more than 10 m depth shall not
of the piles or as required to cater for handling stresses be used without ensuring their construction feasibility
whichever is greater. The lateral reinforcement shall and load carrying capacity by initial load tests in
be links or spirals preferably of not less than 6 mm advance. In view of additional anchorage available
with the provision of bulbs, under-reamed piles can
diameter bars. The cover of concrete over all the
be used with advantage to resist uplift loads.
reinforcement including bending wire should not be
less than 40 mm, but where the piles are exposed to 11.1 Materials
the sea-water or water having other corrosive contents
.-
the cover should be no where less than 50 mm. A thin 11.1.1 Provisions of 8.1 shall generally apply.
gauge sheathing pipe of approximately 40 mm
11.2 Design Considerations
diameter may be attached to the reinforcement cage,
in case of solid piles, to form the central duct for 11.2.1 General
pumping grout to the bottom of the bore.
Under-reamed pile foundation shall be designed in such
10.4 For detailed information regarding casting and away that the load from the structure they support can
curing, storing and handling, control of pile installation be transmitted to the soil without causing failure of
and recording of data, reference maybe made to good soil or failure of pile material and without causing
practice [6-2(21)]. settlement (differential or total) under permanent
transient loading as may result in structured damage
11 UNDER-REAMED PILES and/or functional distress (see Fig. 7).
11.0 General 11.2.1.1 In deep deposits of expansive soils the
Under-reamed piles are bored cast in-situ and bored minimum length of piles, irrespective of any other
compaction concrete types having one or more bulbs considerations, shall be 3.5 m below ground level. If
formed by enlarging the borehole for the pile stem. the expansive soil deposits are of shallow depth and
These piles are suited for expansive soils which are overlying on non-expansive soil strata of good bearing
often subjected to considerable ground movements due or rock, piles of smaller length can also be provided.
to seasonal moisture variations. These also find wide In recently filled up grounds or other strata or poor
application in other soil strata where economics are bearing the piles should pass through them and rest in
favorable. When the ground consists of expansive soil, good bearing strata.
for example, black cotton soils, the bulb of under-
11.2.1.2 The minimum stem diameter of under-reamed
reamed pile provide anchorage against uplift due to
pile can be 200 mm up to 5 @ depth in dry conditions,
swelling pressure, apart from the increased bearing,
that is strata with low water table. The minimum stem
provided topmost bulb is formed close to or just below
diameter for piles up to 5 m depth in strata with high
the bottom of active zone. Negative slopes may not be
water table within pile depth, shall be 300 mm for
stable in certain strata conditions, for example, in pure
normal under-reamed pile and 250 mm for compaction
sands (clean sands with fines less than five per cent)
under-reamed pile. For piles of more than 5 m depth,
and very soft clayey strata having N of SPT less than
the minimum diameter in two cases shail be 375 mm
2 (undrained shear strength of less than 12.5 kN/m2).
and 300 mm respectively. The minimum diameter of
Hence formation of bulb(s) in such strata is not
stem for strata consisting of harmful constituents, such
advisable. In subsoil strata above water table, the
as sulphates, should also be 375 mm.
maximum number of bulbs in underreamed pile should
be restricted to four. In the strata such as clay, silty 11.2.1.3 The diameter of under-reamed bulbs may
clay and clayey silt with high water table where sides vary from 2 to 3 times the stem diameter, depending,

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 29


P

G- =/s’’’’”” a
GL

7K liAw “w tl FIRST BULB

BORING LEVEL FOR 3I


MAKING FIRST BULB

SECOND/iAST
w 1,”” ——A II

BULB

I---Q-l
75 TO 100J D“ 4

01 = 45° (APPROX.)
02 = 30°-’45° (APPROX)
Du = NORMALLY 2.5 D

7A SECTION OF SINGLE - 7B SECTIOht UF MULTl-


UNDER - REAMED PILE UNDER-REAMED PILE

All dimensions in millimetres.

FIG. 7 TYPICALDETAILSOF BORED CAST IN-SITU UNDER-REAMEDPILE FOUNDATION

upon the feasibility of construction and design 11.2.1.6 Under-reamed piles with more than one bulb
requirements. In bored cast in-situ under-reamed piles are not advisable without ensuring their feasibility in
and under-reamed compaction piles, the bulb diameter strata needing stabilization of bore holes by drilling mud.
shall be normally 2.5 and 2 times the stem diameter The number of bulbs in the case of bored compaction
respectively. piles should also not exceed one in such strata.

11.2.1.4 For piles of up to 300 mm diameter, the 11.2.1.7 Under-reamed batter piles without lining in
spacing of the bulbs should not exceed 1.5 times the dry conditions, that is, strata with low water table can
diameter of the bulb. For piles of diameter greater than be constructed with batter not exceeding 15°.
300 mm, spacing can be reduced to 1.25 times the bulb
11.2.2 Safe Load
diameter.
Safe load on a pile can be determined:
11.2.1.5 The topmost bulb should be at a minimum
depth of two times the bulb diameter. In expansive a) by calculating the ultimate load from soil
soils it should also be not less than 2.75 m below properties and applying a suitable factor of
ground level. The minimum clearance below the safety as given in Annex J;
underside of pile cap embedded in the ground and b) by load test on pile as good practice [6-2(18)];
the bulb should be a minimum of 1.5 times the bulb and
diameter. c) from safe load tables.

30 NATIONAL BUILDING CODE OF INDIA


11.2.2.1 Load test and non-destructive testing Reinforcement is to be provided in full length and
further a minimum of 3 bars of 10 mm diameter mild
Provisions of 8.2.1.4 and 8.2.1.5 shall generally apply.
steel or three 8 mm diameter high strength steel bars
11.2.2.2 In the absence of detailed sub-soil shall be provided. Transverse reinforcement shall not
investigations and pile load tests for minor and less be less than 6 mm diameter at a spacing of not more
important structures, a rough estimate of safe load on than the stem diameter or 300 mm, whichever is less.
piles may be made from the Safe Load Table in
In under-reamed compaction piles, a minimum number
accordance with good practice [6-2(22)].
of four 12 mm diameter bars shall be provided. For
11.2.3 Negative Skin Friction or Dragdown Force piles of lengths exceeding 5 m and of 375 mm
diameter, a minimum number of six 12 mm diameter
Provisions of 8.2.2 shall generally apply subject to the
bars shall be ,provided. For piles exceeding 400 mm
condition that the under-reamed bulb is provided below
diameter, a minimum number of six 12 mm diameter
the strata susceptible to negative skinfriction.
bars shall be provided. The circular stirrups for piles
IL2.4 Structural Capaci@ of lengths exceeding 5 m and diameter exceeding
375 mm shall be minimum 8 mm diameter bars.
Provisions of 8.2.3 shall generally apply except that
the under-reamed pile stem is designed for axial capacity For piles in earthquake prone areas, a minimum number
as a short column. Under-reamed piles under lateral of six bars of 10 mm diameter shall be provided. Also
loads and moments tend to behave more as rigid piles transverse reinforcement in the form of stirrups or
due the presence of bulbs and therefore the analysis helical should be at 150 mm centre-to-centre in top
can be done on rigid pile basis. Nominally reinforced few metre depth.
long single bulb piles which are not rigid may be 11.2.8.2 The minimum clear cover over the
analyzed as per the method given in Annex H or as longitudinal reinforcement shall be 40 mm. In
per other accepted methods. aggressive environment of sulphates etc, it may be
11.2.5 Spacing increased to 75 mm.

11.2.5.1 Generally the centre to centre spacing for 11.2.9 The design of pile cap and grade beams shall
bored cast in-situ under-reamed piles in a group should conform to the requirements specified in 8.2.10 and
be two times the bulb diameter (2 Du). It shall not be 8.2.11 respectively.
less than 1.5 Du. For under-grade beams, the maximum
11.2.10 For detailed information on under-reamed
spacing of piles should generally not exceed 3 m. In
piles regarding control of pile, installation, reference
under-reamed compaction piles, generally the spacing
may be made to good practice [6-2(22)].
should not be less than 1.5 DU. If the adjacent piles are
of different diameter, an aveage value of bulb diameter 12 TIMBER PILES
should be taken for spacing.
12.1 Materials
11.2.6 Group Efficiency
12.1.1 Timber
For bored cast in-situ under-reamed piles at a usual
spacing of 2 Du, the group efficiency will be equal to The timber shall have the following characteristics:
the safe load of an individual pile multiplied by the a) Only structural timber shall be used for piles
number of piles in the group. For piles at a spacing of (see Part 6 ‘Structural Design, Section 3 Timber
1.5 Du, the safe load assigned per pile in a group should and Bamboo, 3A’ Timber’ );
be reduced by 10 percent.
b) The length of an individual pile shall be:
In under-reamed compaction piles, at the usual spacing 1) the specified,,@gth * 300 mm for piles
of 1.5 Du, the group capacity will be equal to the safe up to and including 12 m in length, and
load on an individual pile multiplied by the number of 2) the specified length & 600 mm for piles
piles in the group. above 12 m in length;
11.2.7 Transient and Overloading c) The ratio of heartwood diameter to the pile
butt diameter shall be not less than 0.8;
Provisions of 8.2.7 and 8.2.8 shall generally apply.
and
11.2.8 Reinforcement d) Piles to be used untreated shall have as little
11.2.8.1 The minimum area of longitudinal sapwood as possible.
reinforcement (any type or grade) within the pile shaft
12.2 Design Considerations
shall be 0.4 percent of the sectional area calculate on
the basis of outside area of the shaft or casing if used. 12.2.1 General — See 8.0.

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 31


12.2,2 Soil Resistance — See 8.2.1. the least lateral dimension, buckling effect shall be
taken into account, but in no case shall the height
12.2.3 Structural Capaci~
exceed 12 times the least lateral dimension.
The pile shall have the necessary structural strength to
When the height exceeds 6 times the least lateral
transmit the load imposed on it to the soil. Load tests
dimension, the deduction in allowable stress shall be
shall be conducted on a single pile or preferably on a
given by the following formula:
group of piles. For compaction piles, test should be done
on a group of piles with their caps resting on the ground
as good practice [6-2(18)]. If such test data is not
available, the load carried by the pile shall be determined
by the Engineering News formula (see Note). where

NOTE— For timber piles, the load carried shall be determined f J = Reduced allowable stress,
by the Engineering News formula given below. Care shall be ~ = Allowable stress,
taken that while counting the number of blows, the head of the
timber pile is not broomed or brushed and in case of interrupted H = Height of pier, and
driving counting shall be done after 300 mm of driving. D = Least lateral dimension.
For piles driven with drop hammer, NOTE — The above provision shall not apply for piers where
the least lateral dimension is 1.8 m or greater.
160 WH
P=— 13.1.1.3 Reinforced concrete piers
S+25

For piles driven with single-acting steam hammer, When the height of the pier exceeds 18 times its least
dimension, the maximum load shall not exceed:
P=160WH
H

()
S i- 2.5
P’=P l.5– —
where 36D
P= Safe load on pile in kN, where
w= Weight of monkey in kN,
H. Free fall of monkey in m, and P’ = Permissible load;
s= Penetration of pile in mm to be taken as the average P= Permissible load when calculated as axirdly
of the last three blows, loaded short column,
H= Height of the pier measured from top of bell,
12.2.4 For detailed information on timber piles
if any, to the level of cut-off of pier, and
regarding spacing, classification, control of pile
driving, storing and handling, reference may be made D= Least lateral dimension.
to good practice [6-2(23)]. 13.2 Design of foundation units not already covered
by this section, such as well foundations, machine
13 OTHER FOUNDATIONS
foundations, shell foundations, etc, may be designed
13.1 Pier Foundations and constructed in accordance with good practice
[6-2(24)].
13.1.1 Design Considerations

13.1.1.1 General 14 GROUND IMPROVEMENT


In poor and weak subsoils, the design of conventional
The design of concrete piers shall conform to the
shallow foundation for structures and equipment may
requirements for columns specified in Part 6 ‘Structural
present problems with respect to both sizing of
Design, Section 5 Concrete’. If the bottom of the pier
is to be belled so as to increase its load carrying
foundation as well as control of foundation settlements.
capacity, such bell shall be at least 300 mm thick at its
A viable alternative in c&tain situations, developed
edge. The sides shall slope at an angle of not less than
over the recent years is to improve the subsoil to an
extent such that the subsoil would develop an adequate
60° with the horizontal. The least permissible
dimensions shall be 600 mm, irrespective of the pier
bearing capacity and foundations constructed after
being circular, square or rectangular. Piers of smaller
subsoil improvement would have resultant settlements
within acceptance limits. Selection of ground
dimensions if permitted shall be designed as piles
improvement techniques may be done in accordance
(see 8 and 9).
with good practice [6-2(25)].
13.1.1.2 Plain concrete piers
Use of suitable geo-synthetics/geo-textiles may be
The height of the pier shall not exceed 6 times the least made in an approved manner for ground improvement,
lateral dimension. When the height exceeds 6 times where applicable; see also good practice [6-2(26)].

32 NATIONALBUILDING CODE OF INDIA


ANNEX A

(Clause 7.3.1.11)
DETERMINATION OF MODULUS OF ELASTICITY (E,)
AND POISSON’S RATIO (u)

A-1 DETERMINATION OF MODULUS OF where B~, BP represent sizes of foundation and plate
ELASTICITY (E,) and EP is the modulus determined by the plate load
test.
A-1.l The modulus of elasticity is a function of
composition of the soil, its void *ratio, stress history A-2.2 For stratified deposits or deposits with lenses
and loading rate. In granular soils it is a function of of different materials, results of plate load test will be
the depth of the strata, while in cohesive soil it is unreliable and static cone penetration tests may be
markedly influenced by the moisture content. Due to carried out to determine E,.
its great sensitivity to sampling disturbance, accurate
A-2.2.1 Static cone penetration tests shall be carried
evaluation of the modulus in the laboratory is extremely
out in accordance with good practice [6-2(1)]. Several
difficult. For general cases, therefore, determination
tests shall be carried out at regular depth intervals up
of the modulus may be based on field tests (A-2).
to a depth equal to the width of the raft and the results
Where properly equipped laboratory and sampling
plotted to obtain an average value of E,:
facility is available, E, may be determined in the
laboratory (see A-3). A-2.2.2 The value of E, may be determined from the
following relationship:
A-2 FIELD DETERMINATION
E,= 2 C~d
A-2.1 The value of E, shall be determined from plate
load test in accordance with good practice [6-2(8)]. where

C~, = Cone resistance in kNlm2.


E, =qB—
o-p’) ~
s“ A-3 LABORATORY DETERMINATION OF E,

where A-3.1 The value of E, shall be determined by*


conducting triaxial test in the laboratory in accordance
~ = Intensity of contact pressure,
with good practice [6-2(4)] on samples collected with
B = Least lateral dimension of test plate, least disturbances.
s = Settlement,
A-3.2 In the first phase of the tri-axial test, the
p = Poisson’s ratio, and
specimen shall be allowed to consolidate fully
lW = Influence ratio . under an all-round confining pressure equal to the
= 0.82 for a square plate. vertical effective overburden stress for the specimen
in the field. In the second phase, after equilibrium
A-2.1.1 The average value of E, shall be based on a
has been reached, further drainage shall be prevented
number of plate load tests carried out over the area,
and the deviator stress shall be increased from zero
the number and location of the tests, depending upon
value to the magnitudp estimated for the field
the extent and importance of the structure.
loading condition. The deviator stress shall then be
A-2.1.2 Effect of Size reduced to zero and the cycle of loading shall be
repeated.
In granular soils the value of E, corresponding to the
size of the raft shall be determined as follows: A-3.3 The value of E, shall be taken as the tangent
modulus at the stress level equal to one-half the
B B~+BP) 2
E,=EP;
P [1 2 B~
maximum deviator stress applied during the second
cycle of loading.

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 33


ANNEX B
(Clause ’J.3.l.11)
DETERMINATION OF MODULUS OF SUBGRADE REACTION

B-1 GENERAL number of plate load tests carried out over the area,
the number and location of the tests depending upon
B-1.l The modulus of subgrade reaction (k) as
the extent and importance of the structure.
applicable to the case of load through a plate of size
300 mm x 300 mm or beams 300 mm wide on the soils B-3 LABORATORY DETERMINATION
is given in Table 6 for cohesionless soils and in Table 7
for cohesive soils. Unless more specific determination B-3.1 For stratified deposits or deposits with lenses
of k is done (see B-2 and B-3) these values may be of different materials, evaluation of k from plate load
used for design of raft foundation in cases where the test will be unrealistic and its determination shall be
depth of the soil affected by the width of the footing based on laboratory tests [see 6-2(4)].
may be considered isotropic and the extra-polation of B-3.2 In carrying out the test, the continuing cell
plate load test results is valid. pressure may be so selected as to be representative of
the depth of the average stress influence zone (about
B-2 FIELD DETERMINATION
0.5 B to B).
B-2.1 In cases where the depth of the soil affected by
B-3.3 The value of k shall be determined from the
the width of the footing maybe considered as isotropic,
following relationship:
the value of k may be determined in accordance with

[r
good practice [6-2(27)]. The test shall be carried out
with a plate of size not less than 300 mm. E#4 ‘2 E, 1
k= O.65x —
EI (1-p’)z
B-2.2 The average value of k shall be based on a

Table 6 Modulus of Subgrade Reaction (k) for Cohesionless Soils


(Clause B-1.1)

Soil Characteristic 1)Modulus of Subgrade Reaction (k)


kN/m3
A A
/— b / \
Relative Density Standard Penetration Test Value (N) For Dry or Moist State For Submerged State
(Blows per 300 mm)
(1) (2) (3) (4)

Loose <10 15000 9000


Medium loto30 15 000to47000 9 000to29000
Dense 30 and over 47000 to 180000 29000 to 108000

1)The above values apply to a square plate 300 mm x 300 mm or beams 300 mm wide.

Table 7 Modulus of Subgrade Reaction (k) for Cohesive Soils


(Clause B-1.1)

Soil Characteristic 1)Modulus of Subgrade Reaction (k)


kNlm3
Consistency Unconfined Compressive Strength,
kN/m2
(1) (2) (3)

Stiff 100 to200 27000


Very Stiff 200to 400 27000to54000
Hard 400 and over 54000 to 108000

1)The values apply to a square plate 300 mm x 300 mm. The above values are based on the assumption that the average loading
intensity does not exceed half the ultimate bearing capacity.

34 NATIONAL BUILDING CODE OF INDIA


where B-4 CALCULATIONS

E, = Modulus of elasticity of soil (see Annex A), When the structure is rigid (see Annex C), the average
E= Young’s modulus of foundation material, modulus of subgrade reaction may also be determined
/4. as follows:
Poisson’s ratio of soil,
I= Moment of inertia of the foundation, and ~ = Average contact pressure
B= Width of the footing. s Average settlement of the raft

ANNEX C

(Clauses 7.3.4 .1,7.3.4.2 and B-4)


RIGIDITY OF SUPERSTRUCTURE AND FOUNDATION

C-1 DETERMINATION OF THE RIGIDITY OF If = Moment of inertia of the foundation beam


THE STRUCTURE or raft in m4 .
NOTE — The summation is to be done over afl the
C-1.l The flexural rigidity EI of the structure of any
storeys including the foundation beam or raft. In the
section may be estimated according to the relation case of the foundation, Z; replaces I; and I, becomes
given below (see also Fig. 8) zero, whereas for the topmost beam Z: becomes zero.

~1 _ E,I, b’ (Z; + Z;)bz


-—+zEJ~ 1+
2 H’ I (1;+1: +1;)121
where

El = Modulus of elasticity of the infilling


material (wall material) in kN/m2,
Ii = Moment of inertia of the infilling in m4,
b= Length or breadth of the structure in the
direction of bending in m,
H= Total height of the infilling in m,
E2 = Modulus of elasticity of the frame material
in kN/m2,
1, = Moment of inertia of the beam in m4,

~FOuNDATION RAFT

Fm. 8 DETERMINATION OF RIGIDITY OF STRUCTURE

C-2 RELATIVE STIFFNESS FACTOR, ~


I = Spacing of the columns in m, C-2.1 Whether a structure behaves as rigid or flexible
hu = Length of the upper column in m, depends on the relative stiffness of the structure and
hi = Length of the lower column in m, the foundation soil. This relation is expressed by the
relative stiffness factor K given below:

El
a) For the whole structure, K = —
Zu = Moment of inertia of the upper column E,b3a
in m4,
E d3
1, = Moment of inertia of the lower column b) For rectangular rafts, K= ~ ;
in m4, and s [)

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 35


Ed3 C-3 DETERMINATION OF CRITICAL COLUMN

where
c) ‘or clrculm ‘afts’ K = 12 E, ()
2R
SPACING

C-3.1 Evaluation of the characteristics k is made ai


follows:
El = Flexural rigidity of the structure over the
length (a) in kN/m2,
E, = Modulus of compressibility of the
foundation soil in kNlm2,
b . Length of the section in the bending axis in u where
a = Length perpendicular to the section under k = Modulus of subgrade reaction in kN/m3 for
investigation in m, footing of width B in m (see Annex B),
*
d = Thickness of the raft or beam in m, and
B = Width of raft Bin m,
R = Radius of the raft in m.
EC = Modulus of elasticity of concrete in kN/m2,
C-2.1.1 For K> 0.5, the foundation maybe considered and
as rigid. 1 = Moment of inertia of raft in m4.

ANNEX D

(Clause 7.3.4.1)

CALCULATION OF PRESSURE DISTRIBUTION BY CONVENTIONAL METHOD

D-1 DETERMINATION OF PRESSURE I


DISTRIBUTION e~=eX–~ey
IX
D-1.l The pressure distribution (q) under the raft shall
I
be determined by the following formula: e~=ey–~ex
Iy

where

11,IY= Moment of inertia of the area of the raft


where respectively about the x and y axes through
the centroid,
Q = Total vertical load on the raft,
Zxy= Jxy dA for the whole area about x and y
A = Total area of the raft,
axes through the centroid, and
e:, e ~, l:, I; = Eccentricities and moments of inertia
e,, ey = Eccentricities in the x and y directions of
about the principal axes through the
the load from the centroid.
centroid of the section, and
x, y = Co-ordinates of any given point on For a rectangular raft, the equation simplifies to:
the raft with respect to the x and y
axes passing through the centroid of lzeyy + 12exx
~=: 1*
the area of the raft. [ bz – a’ 1
l;, I; e:, e’y may be calculated from the following where
equations: a and b = the dimensions of the raft in the x and y

z:=+ Y
directions respectively.
NOTE — If one or more of the values of (q) are nagative as
calculated by the above formula, it indicates that the whole area
of foundation is not subject to pressure and only a part of the
2 area is in contact with the soil, and the above formula will still
hold good, provided the appropriate vatues of 1,,1,, Iv, exand ey,
Z;= IY–+
are used with respect to the area in contact with the soil instead
x of the whole area.

36 NATIONAL BUILDING CODE OF INDIA


ANNEX E
(Clause 7.3.4.2)
CONTACT PRESSURE DISTRIBUTION AND MOMENTS BELOW
FLEXIBLE FOUNDATION

E-1 CONTACT PRESSURE DISTRIBUTION E-1.2 The contact pressure for the full width of the
strip under an interior column load located at a point i
E-1.l The distribution of contact pressure is assumed
can be determined as (see Fig. 9 A):
to be linear with the maximum value attained under
the columns and the minimum value at mid span. 5P 48M.
“ = i’+ (o”

I I
I
i-l ~j+l
———— T I ———— —
1/2
I
112
I
I

pi (r)
pi (1)

————————

9B PRESSURE DISTRIBUTION OVER .


9A MOMENT AND PRESSURE DISTRIBUTION
AN INTERIOR SPAN
AT INTERIOR COLUMN *

Pe Pi
.Ii .
k &

I 1/2 / 112

1
///\\\l
b
///\\\ I ///\\\ I ///’N\
1; I I
I
I

I I I I I I

L EXTERIOR PART

9C MOMENT AND PRESSURE DISTRIBUTION AT EHERIOR COLUMNS

FIG. 9 MOMENT AND PRESSUREDISTRIBUTIONAT COLUMNS

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 37

..
‘
where 4 pe – pmlr
i= Average length of adjacent span (m), “ ‘p’ = 4C+1,
P, = Column load at point i, and
Ml = Moment under an interior columns loaded E-2 BENDING MOMENT DIAGRAM
at i. E-2.1 The bending moment under an interior column
E-1.3 The minimum contact pressure for the full width located at i (see Fig. 9A) can be determined as:
of the strip at the middle of the adjacent spans can be
determined as (see Fig. 9A and 9B). M, = fi(O.24 AT +0.16)

‘“=2++J”P’F) E-2.2 The bending moment at mid span is obtained


as (see Fig. 9A):

M~=MO+Mi

‘m=’t+l-pi[:) pm + pti
where

MO = Moment of simply supported beam


P.= ‘

E-1.4 If E-2.3 (a) governs the moment under the ‘~[Pi~z)+4 Pm ‘fi(r)l
exterior columns, contact pressures under the exterior
columns and at end of strip can be determined as (see Mi = Average of negative moments Mi at each
Fig. 9C): end of the bay.

6 ikf~ E-2.3 The bending moment M. under exterior columns


4pe+ —–’ml, can be determined as the least of (see Fig. 9C):
‘e = c
C+l,
a) Mel =–$--(0.13 AZl+1.06 AC–O.50)

E-1.5 If E-2.3 (b) governs the moment under the (4< - pml,) c’
b) M., ‘- (4c+/1) ‘
exterior columns, the contact pressures are determined
as (see Fig. 9C):

ANNEX F

(Clause 7.3.4.2)
FLEXIBLE FOUNDATION — GENERAL CONDITION

F-1 CLOSED FORM SOLUTION OF ELASTIC where


PLATE THEORY
P= Column load,
F-1.l For a flexible raft foundation with non-uniform r= Distance of the point under investigation
column spacing and load intensity, solution of the
from column load along radius, and
differential equation governing the behaviour of plates
L= Radius of effectiye stiffness
on elastic foundation (Winkler Type) gives radial
moment (M,) tangential moment (Mt) and deflection

(r
D4
(w) at any point by the following expressions:
T
z;(f) where
M, =-: Z,(~)-(l-@-
[ (f) 1 k= Modulus of subgrade reaction for footing
of width B,
z;(f)
M, =-: /JZ, (~)+(l-p)— D= Flexural rigidity of the foundation,
[ (f) 1 Et’
P=
w. g. z, (f) I’(l–/l’)’

38 NATIONALBUILDINGCODE OF INDIA
%--’

t = Raft thickness, assuming the raft to be infinitely large. Then apply


E= Modulus of elasticity of the foundation opposite and equal moments and shears on the edge of
material, the mat. The method for beams on elastic foundation
Possion’s ratio of the foundation material, may be used.
P=
and F-1.5 Finally, all moments and shears calculated for
each individual column and wall are superimposed to
z3&
() obtain the total moment and shear values.
z;;,
() = Functions of shear, moment and
deflection (see Fig. 10) 0.5
z, (f),

N
0.4
Z“(rA)
F-1.2 The radial and tangential moments can be
0.3 ~(rA)
converted to rectangular co-ordinates:

MY= M, cosz@ + M, sinz~ 0,2

M, = M, sin~~ + M, cos2@ 0.1

where
0
# = Angle with x-axis to the line jointing origin
to the point under consideration. -0.1

F-1.3 The shear Q per unit width of raft can be -0.2


determined by:
-0.3 N \
k!!!(rl)

Q=.--& q;) -0.4 ~\


I Z’(rA)
I
z: (;) = function for shear (see Fig. o). -0.5
L i 1 t t

0123456
F-1.4 When the edge of the raft is located within the
r7L
radius of influence, the following corrections are to be
applied. Calculate moments and shears perpendicular FIG.10 FUNCTIONSFOR SHEAR MOMENT
to the edge ,of the raft within the radius of influence, AND DEFLECTION

ANNEX G
(Clauses 8.2.1.2 and 8.2.3.2)
LOAD CARRYING CAPACITY — STATIC FORMULA

G-1 PILES IN GRANULAR SOILS PD = Effective overburden pressure at pile toe


in kN/m2;
G-1.l The ultimate bearing capacity (QU) of piles in
granular soils is given by the following formula: NY,N~ = Bearing capacity factors and depending
upon the angle of internal friction O, at toe;
. n

Qu = A, (~ ~.Y. N, + PD.Nq) + ~ K.PDitan &A,, Summation for n layers in which pile is


j=l
installed;
where K= Coefficient of earth pressure;
Ar = Cross-sectional area of pile toe in m2; P=Di Effective overburden pressure in kN/m2 for
D= Stem diameter in m; the ith layer, where i varies from 1 to n;
y= Effective unit weight of soil at pile toe in 6 = Angle of wall friction between pile and soil,
kIWm3; in degrees (maybe taken equal to@); and

PART 6 STRUCTURAL DESIGN— SECTION 2 SOILSAND FOUNDATIONS 39


i?
1’
A,i = Surface area of pile stem in mz in the ith Type of Soil Local Side Friction
layer, where i varies from 1 to n.
h
NOTES
q
1 For NT factors refer to good practice [6-2(7)]. Clays and peats where qC<1 ~ <& < ~
2 N~factor will depend, apart from nature of soil on the type of
pile and the method of its construction and the values are given 2 q,
in Fig. 11 and Fig. 12 for bored and driven piles respectively. Clays ~q <f, < —
2.5 2.5
3 The earth pressure coefficient K depends on the nature of
soil strata, type of pile and the method of its construction. For q. <f, < &
Silty clays and silty sands
driven piles in loose to medium sands, K values of 1 to 3 should ii)
be used. For bored piles, k values can be taken between 1 and 2.
!? 2qc
4 The angle of wall friction maybe taken equal to the angle of Sands J- <f, < —
shear resistance of soil. 10 10
5 In working out pile capacities using static formula, for piles
larger than 15 to 20 pile diameters, the maximum effective Coarse sands and gravels f,< g
overburden at the pile tip should correspond to pile length equal
to 15 to 20 times of the diameters.
where
G-2 PILES IN COHESIVE SOILS
qC= Static point resistance in N/mm2, and
G-2.1 The ultimate bearing capacity of piles (QU) in & = Local side friction in N/mm’.
cohesive soil is given by the following formula:
For non-homogeneous soils, the ultimate point bearing
Q. = APNC.c,+ aC. A, capacity may be calculated using the following
where relationships:
A, = Cross-sectional area of pile toe in mz,
%++ + 9,2
NC = Bearing capacity factor usually taken as 9,
q“ =
c, = Average cohesion at pile tip in kN/m2, 2
a= Reduction factor, where
c. Average cohesion throughout the length of
pile in kN/m2, and 9. = Ultimate point bearing capacity,
A, = Surface area of pile shaft in m2. f?co= Average static cone resistance over a depth
of 2 d below the base level of the pile,
NOTES
q., = Minimum static cone resistance over the
1 The following values of et may be taken, depending upon
the consistency of the soils:
same 2 d below the pile tip,
qcz = Average of the minimum cone resistance
Consistency N Value Valueof a values in the diagram over a height of 8 d
#- Y
Bored piles Driven cast above the base level of the pile, and
in-situ pifes d= Diameter of the pile base or the equivalent
(1) (2) (3) (4)
diameter for a non-circuhu cross-section.
Soft to very soft <4 0.7 1
Medium 4t08 0.5 0.7 G-3.1 The correlation between standard penetration
stiff 8to15 0.4 0.4 test value N and static point resistance qC(in N/mmz)
Stiff to hard >15 0.3 0.3
given below may be used for working out the shaft ‘,

2 a) Static formula maybe used as a guide only for bearing resistance and skin friction of piles:
capacity estimates. Better reliance may be put on load
test on piles. Soil type ‘ qclN
b) For working ont safe load, a minimum factor of safety
Clays, silts, sandy silts and slightly 0.2
2.5 should be used on the ultimate bearing capacity
estimated by static formulae. cohesive silt-sand mixtures
3 In case of soft to very soft soils which are not sensitive, the Clean fme to medium sands and 0.3-0.4
value of a can be taken up to 1. slightly silty sands
G-3 When full static penetration data is available for Coarse sands and sands with little 0.5-0.6
the entire depth, the following correlations may be used gravel
as a guide for the determination of shaft resistance of
Sandy gravels and gravel 0.8-0.10
a pile:

40 NATIONAL BUILDING CODE OF INDIA


500

100

50

10
20 25 30 35 40 45

ANGLE OF INTERNAL FRICTION, 0

FIG. 11 BEARINGCAPACITY
FACTOR,NqFORBOREDPILES

100
/
/

I
50

10
20 25 30 35 40 45

ANGLE OF INTERNAL FRICTION, 0

FIG. 12 BEARINGCAPACITY
FACTOR,Nq FORDRIVENPILES

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS


ANNEX H
(Clauses 8.2.3.3 and 11.2.4)
DETERMINATION OF DEPTH OF FIXITY, LATERAL DEFLECTION
AND MAXIMUM MOMENT OF LATERALLY LOADED PILES

H-1 DETERMINATION OF LATERAL Table 8 Values of Constant K1 (kN/m3)


DEFLECTION AT THE PILE HEAD AND DEPTH (Clause H-1 .2)
OF FIXITY
Type of Soil Value
H-1.l The long flexible pile, fully or partially Dry Submerged’
embedded, is treated as a cantilever fixed at some depth
(1) (2) (3)
below the ground level (see Fig. 13).
Loose sand 2600 1460
H-1.2 Determine the depth of fixity and hence the Medium sand 7750 5250
equivalent length of the cantilever using the plots given Dense sand 20750 12450
Very loose sand under repeated — 400
in Fig. 13. loading or normally loading clays

where
Table 9 Values of Constant K1 (kN/m3)
(Clause H-1.2)

Unconfhed Compressive Strength Value

(Kl and Kz are constants given in Tables 8 and 9, E kN/m2

is the Young’s modulus of the pile material in (1) (2)


kN/m2 and 1 is the moment of inertia of the pile 20 to 40 7.75 x 104
cross-section in m4). 100 to 200 48.80 X 104
200 to 400 97.75 x 104
NOTE — Figure 12 is valid for long flexible piles where the More than 400 195.50 x 1(%
embedded length Le is> 4R or 4T.

— FREE HEAD PILE

k
2.1
1
\
‘1,
‘----- FIXED HEAD PILE
“~+ ‘~~,

FOR PILES IN SANDS


AND NORMALLY
} LOADED CLAYS
“\
I \

1.5
--- ---9 -----
FOR PILES IN
PRELOADED
,}
1 I I 1 CLAYS
1.3
o 2 4 6 8 10

L1/R OR Lqfl

FIG. 13 DETERMINATION
OFDEPTHFIXITY

42 NATIONAL BUILDING CODE OF INDIA

..
L
H-1.3 Knowing the length of the equivalent cantilever cantilever is higher than the actual maximum moment
the pile head deflection (Y) shall be computed using (M) of the pile. The actual maximum moment is
the following equations: obtained by multiplying the fixed end moment of the
equivalent cantilever by a reduction factor, m given in
Y(in ,n)= Qf~ +~f)’ ...... for free head pile Fig. 14. The fixed end moment of the equivalent
3 EI
cantilever is given by:
=Q(L+G)3 ...... for fixed head pile
12 EI A4f = Q (Ll + Lf) ...... for free head pile

where Q is the lateral load in kN.


= Q(J4+Q3 ...... for fixed head pile
H-2 DETERMINATION OF MAXIMUM
12 EI
MOMENT IN THE PILE
H-2.1 The fixed end moment (MJ of the equivalent The actual maximum moment (M) = m (MF ).

1.0

0.8

0.6

0.4

0.2
0 2 4 6 8 10 12
LIIR OR Lf/T
Q
FOR PILES IN L1
PRELOADED CLAYS Ll+ Lf
.— FOR PILES IN SANDS AND R
Le
NORMALLY LOADED CLAYS
l-l *

t
14A FOR FREE HEAD PILE

1.0

0.8

0.6
o 0.5 1.0 1.5 2.0 2,5
$

L1/R OR LI/T

— FOR PILES IN
PRELOADEJ) CU4YS f’+=fQ~: Ll+ Lf
— — FOR PILES IN SANDS AND
NORMALLY LOADED CLAYS

14B FOR FIXED HEAD PILE

FIG. 14 DETERMINATION
OFREDUCTION
FACTORS
FORCOMPUTATION
OFMAXIMUMMOMENTINPILE

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 43

..
-y-?

ANNEX J

(Clause 11.2.2)

LOAD CARRYING CAPACITY OF UNDER-REAMED PILES


FROM SOIL PROPERTIES

J-1 ULTIMATE LOAD CAPACITY n = Number of under-reamed bulbs;


y = Average unit weight of soil (submerged unit
The ultimate load capacity of a pile can be calculated
weight in strata below water table) in
from soil properties. The soil properties required are
kN/m3;
strength parameters, cohesion, angle of internal friction
and soil density. NY,N~ = Bearing capacity factors, depending upon
the angle of internal friction;
a) Clayey Soils — For clayey soils, the ultimate
dr = Depth of the centre of different under-
load carrying capacity of an under-reamed
reamed bulbs below ground level in m;
pile may be worked out from the following
expression: df = Total depth of pile below ground level in m;
K = Earth pressure coeftlcient (usually taken as
Qu = APNCCP+ AaNcC’a+ C’,A’, + aCaA, 1.75 for sandy soils);
where 6 = Angle of wall friction (may be taken as
Qu = Ultimate bearing capacity of pile in kN; equal to the angle of internal friction 0);
d, = Depth of the centre of the first under-
A, = Cross-sectional area of the pile stem at the
reamed bulb in m; and
toe level in mz;
d, = Depth of the centre of the last under-reamed
N, = Bearing capacity factor, usually taken as 9;
bulb in m.
c, = Cohesion of the soil around toe in kN/mz
NOTES
A= = (7c/4) (Duz - D’), where Du and D are the
1 For uplift bearing on pile tip, Ap will not occur.
under-reamed and stem diameter, respectively
2 N, will be as specified in good practice [6-2(7)]
in m; and N~ will be taken from Fig. 11.
c= = Average cohesion of the soil along the pile
c) Soil Strata having both Cohesion and Friction
stem in kN/m2; — In soil strata having both cohesion and
A, = Surface area of the stem in mz; friction or in layered strata having two types
A’, = Surface area of the cylinder circumscribing of soil, the bearing capacity maybe estimated
the under-reamed bulbs in mz; using both the formulae. However, in such
c: = Average cohesion of the soil around the cases load test will be a better guide.
under-reamed bulbs; and d) Compaction Piles in Sandy Strata — For
a= Reduction factor (usually taken 0.5 for clays). bored compaction piles in sandy strata, the
NOTES formula in (b) shall be applied but with the
1 The above expression holds for the usual spacing of under- modified value of $, as given below:
reamed bulbs spaced at not more than one and a half times
their diameter.
$,= (r) + 40)/2
2 If the pile is with one bulb only, the third term will not where ,.
occur. For calculating uplift load, the first term will not occur
in the formula. $ = Angle of internal friction of virgin soil.
3 In case of expansive soil top 2 m strata should be neglected
The values of NY, N~ and 8 are taken
for computing skin friction,
corresponding to@ ~, The value of the earth
b) Sandy Soils pressure coefficiefit K will be 3.

Q. = ~(fiDTN, +vf,N,)+4(~D.n~N, ) e) Piles Resting on Rock — For piles resting on


i-=11 rock, the bearing component will be obtained
+yNJd, +%n DYKtanr5(d; +d; +d:) by multiplying the safe bearing capacity of
,=]
where rock with bearing area of the pile stem plus
the bearing provided by the bulb portion.
AP = z D214, where D is stem diameter in m;
NOTE— To obtain safe load in compression and uplift
A, = n /4 (D: – D2) where DU is the under- from ultimate load capacity generallythe factors of safety
reamed bulb diameter in m: will be 2.5 and 3 respectively.

44 NATIONAL BUILDING CODE OF INDIA


LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’ (Part 3/See 1): Determination of specific
in the fulfillment of the requirements of the Code. The 1980 gravity, Section 1 Fine grained
latest version of a standard shall be adopted at the time soils (first revision)
of enforcement of the Code. The standards listed may
(Part 3/See 2): Determination of specific
be used by the Authority as a guide in conformance
1980 gravity, Section 2 Fine, medium
with the requirements of the referred clauses in the
and coarse grained soils (jlrst
Code. “
revision)
IS No. Title (Part 4): i985 Grain size analysis (second
(1) 1892:1979 Code of practice for subsurface revision)
investigation for foundation (Part 5): 1985 Determination of liquid and
(@W revision) plastic limits (second
2131:1981 Method of standard penetration revision)
test for soils (@W revision) (Part 10) :1991 Determination of unconfined
2132:1986 Code of practice for thin walled compressive strength (second
revision)
tube sampling of soils (second
revision) (Part 13) :1986 Direct shear test (second
revision)
4434:1978 Code of practice for in-situ
vane shear test for soils (@-st (Part 15) :1986 Determination of consolidation
revision) properties (@t revision)

4968 Method for sub-surface (Part 28) :1974 Determination of dry density of
sounding for soils: soils in place, by the sand
replacement method (first
(Part 1) :1976 Dynamic method using 50 mm
revision)
cone without bentonite slurry
(Part 29) :1975 Determination of dry density of
(jirst revision)
soils in place, by the core cutter
(Part 2) :1976 Dynamic method using cone method (first revision)
and bentonite slurry (first
(Part 33) :1971 Determination of the density
revision)
in-place by the ring and water
(Part 3) :1976 Static cone penetration test replacement method
(first revision)
(Part 34) :1972 Determination of density of
8763:1978 Guide for undisturbed soils in-place by rubber-
sampling of sands and sandy balloon method
soils
(Part 39/See 1): Direct shear test for soils
9214:1979 Method for determination of 1977 containing gravel, Section 1
modulus of subgrade reaction Laboratory test
(k-value) of soils in the field (5) 1498:1970 Classification and identification
(2) 10042:1981 Code of practice for site- of soils for general engineering
investigations for foundation in purposes (@t revision)
,,
gravel boulder deposits (6) 401:2001 Code of practice for preservation
(3) 13365 Guidelines for quantitative of timber (jourth revision)
(Part 1): 1998 classification systems of rock (7) 6403:1981 Code of practice for
mass: Part 1 RMR for predicting determination of bearing
of engineering properties capacity of shallow foundations
(4) 2720 Methods of tests for soils: (jirst revision)
(Part 1): 1983 Preparation of dry soil samples (8) 1888:1982 Method of load tests on soils
for various tests (second (second revision)
revision) (9) 2131:1981 Method for standard
(Part 2) :1973 Determination of water content penetration test for soils (lirst
(second revision) revision)

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 45


IS No. Title IS No. Title

(10) 8009 Code of practice for calculation (Part 1): 1982 Foundations for reciprocating
(Part 1): 1976 of settlement of foundations: type machine (second revision)
Part 1 Shallow foundations (Part 2): 1980 Foundations for impact type
subjected to symmetrical static machines (hammer foundations)
vertical loads @rst revision)
(11) 1904:1986 Code of practice for design and (Part 3): 1992 Foundations for rotary type
construction of foundations in machines (medium and high
soils: General requirements frequency) (second revision)
(third revision)
(Part 4): 1979 Foundations for rotary type
(12) 3764:1992 Code of safety for excavation machines of low frequency
work (first revision)
first revision)
(13) 456:2000 Code of practice for plain and
(Part 5): 1987 Foundations for impact
reinforced concrete (fourth
machines other than hammers
revision)
(forging and stamping press;
(14) 1905:1987 Code of practice for structural pig breakers, drop crusher and
use of unreinforced masonry jetter) @rst revision)
(third revision)
13301:1992 Guidelines for vibration
(15) 1080:1985 Code of practice for design isolation for machine
.-
and construction of shallow foundations
foundations in soils (other than
9556:1980 Code of practice for design and
raft, ring and shell) (second
construction of diaphragm walls
revision)
(25) 13094:1992 Guidelines for selection of
(16) 11089:1984 Code of practice for design
ground improvement techniques
and construction of ring
for foundation in weak soils
foundations
(26) 13162 Geotextiles — Methods of test:
(17) 2911 Code of practice for design
(Part 2): 1991 Part 2 Determination of
and construction of pile
resistance to exposure of ultra-
foundations:
violet light and water (Xenon
(Part l/See 1): Concrete piles, Section 1 Driven
arc type apparatus)
1979 cast in-situ concrete piles (first
revision) 13321 Glossary of terms for geo-
(Part 1): 1992 synthetics: Part 1 Terms used
(Part l/See 2): Concrete piles, Section 2 B?red
in materials and properties
1979 cast in-situ piles (first revision)
13325:1992 Method of test for the
(18) (Part 4): 1985 Load test on piles @-st revision)
determination of tensile
(19) 14893:2001 Guidelines for non-destructive
properties of extruded polymer
integrity testing of piles
geogrids using the wide strip
(20) 2911 Code of practice for design
13326 Method of test for the
and construction of pile
(Part 1): 1992 evaluation of interface friction
foundations:
between geosynthetics and soil:
(Part l/See 3): Concrete piles, Section 3 Wrt 1 Modified direct shear
1979 Driven precast concrete piles technique
(jirst revision)
14293:1995 Geotextiles — Method of test
(21) (Part l/See 4): Concrete piles, Section 4 Bored for trapezoid tearing strength
1979 precast concrete piles
14294:1995 Geotextiles — Method for
(22) (Part 3) :1980 Under-reamed pile foundation determination of apparent
(jlrst revision) opening size by dry sieving
(23) (Part 2): 1980 Timber piles (first revision) technique
(24) 2974 Code of practice for design 14324:1995 Geotextiles — Methods of test
and construction of machine for determination of water
foundation permeability-permittivity

46 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title

14706:1999 Geotextiles — Sampling and 14986:2001 Guidelines for application of jute


preparation of test specimens gee-grid for rain water erosion
14714:1999 Geotextiles — Determination control in road and railway
of abrasion resistance embankments and hill slopes
14715:2000 Woven jute geotextiles — 15060:2001 Geotextiles — Tensile test for
Specification joints/seams by wide width
14716:1999 Geotextiles — Determination method
of mass per unit area (27) 9214:1979 Method of determination of
14739:1999 Geotextiles — Methods for subgrade reaction (K-value) of
determination of creep soils in the field

PART 6 STRUCTURAL DESIGN — SECTION 2 SOILS AND FOUNDATIONS 4’?


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 3 Timber and Bamboo: 3A Timber

,--

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD . .. 3

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 SYMBOLS . .. 6
4 MATERIALS . .. 7
5 PERMISSIBLE STRESSES ... 21
6 DESIGN CONSIDERATIONS ... 22
7 DESIGN OF COMMON STEEL WIRE NAIL JOINTS ... 26
8 DESIGN OF NAIL LAMINATED TIMBER BEAMS ... 32
9 DESIGN OF BOLTED CONSTRUCTION JOINTS ... 34
10 DESIGN OF TIMBER CONNECTOR JOINTS ... 37
11 GLUED LAMINATED CONSTRUCTION AND FINGER JOINTS ... 40
12 LAMINATED VENEER LUMBER ... 41
13 DESIGN OF GLUED LAMINATED BEAMS ... 42
14 STRUCTURAL USE OF PLYWOOD ... 43
15 TRUSSED RAFTER ... 43
16 STRUCTURAL SANDWICHES ... 45
17 LAMELLA ROOFING ... 46
18 NAIL AND SCREW HOLDING POWER OF TIMBER ... 48
19 PROTECTION AGAINST TERMITE ATTACK IN BUILDINGS ... 48

LIST OF STANDARDS ... 49

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Section deals with the structural design aspect of timber structures. In this section, the various Species of
Indian timber, classified into three groups depending on the structural properties influencing the design, most are
included.

In the previous version of the Code, timber was covered under Section 3 of Part 6 under the title ‘Wood’, which
did not cover bamboo. Now this Section 3 has been enlarged as Section 3 Timber and Bamboo, which has been
sub-divided into sub-section 3A Timber and sub-section 3B Bamboo. This sub-section pertains to 3A Timber.

This Section was first published in 1970 which was subsequently revised in 1983. In the first revision provisions
of this Section were updated and design of nailed laminated timber beams were included and information on
bolted construction joints was added. As a result of experience gained in implementation of 1983 version of this
Code and feedback received as well as formulation of new standards in the field and revision of some of the
existing standards, a need to revise this Section was felt. This revision has, therefore, been brought out to take
care of these aspects. The significant changes incorporated in this revision include the following:

a) A number of terminologies related to timber for structural purpose have been added.
b) Strength data of additional species of timber have been included.
c) Requirements for structural timber and preferred cut sizes thereof have been modified.
d) Requirements for glued laminated construction and finger joints have been introduced.
e) Requirements for laminated veneer lumber have been introduced.
f) Brief details have been included for structural sandwiches, glued laminated beams, lamella roofing, nail
and screw holding power of timber, structural use of plywood and trussed rafter; these are proposed to
be further elaborated in future revisions of this Section.
d Guidelines for protection against termite attack in buildings have been added.
h) Reference to all the concerned Indian Standards have been updated.

In the present day context of dwindling forest resources, all efforts are being made to effect judicious use of timber.
In this context, the Indian Standards now permit use of plantation timbers including certain fast growing species and
suitable guidelines in terms of their seasoning, sawing, treatment, etc have been made available. In the same way,
use of finger jointing and glued laminated timber is important and standardization on the same is desirable and is
under due consideration. However, in the absence of detailed Indian Standard Specifications and Codes of practice
in these areas at present, general details on the same have been incorporated in the revision of this part.

The information contained in this Section is largely based on the following Indian Standards:

IS No. Title
399:1963 Classification of commercial timbers and their zonal distribution (revised)
883:1994 Code of practice for design of structural timber in building (@rth revision)
1150:2000 Trade names and abbreviated symbols for timber species (third revision)
2366:1983 Code of practice for nail-jointed timber construction (first revision)
4891:1988 Specification for prefen-ed cut sizes of structural timber (&st revision)
4983:1968 Code of practice for design and construction of nailed laminated timber beams
11096:1984 Code of practice for design and construction of bolt-jointed timber construction
14616:1999 Specification for laminated veneer lumber

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 3


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 3 Timber and Bamboo: 3A Timber

1 SCOPE which is determined on small clear specimen of timber,


in accordance with good practice [6-3A(2)]; and does
1.1 This Section relates to the use of structural timber
not take into account the effect of naturally occurring
in structures or elements of structures connected
characteristics and other factors.
together by fasteners/fastening techniques.
2.1.9 Inside Location — Position in buildings in which
1.2 This shall not be interpreted to prevent the use of
timber remains continuously dry or protected from
material or methods of design or construction not
weather.
specifically mentioned herein; and the methods of
design may be based on analytical and engineering 2.1.10 Laminated Veneer Lumber — A structural
principles, or reliable test data, or both, that composite made by laminating veneers, 1.5 mm to
demonstrate the safety and serviceability of the 4.2 mm thick, with suitable adhesive and with the grain
resulting structure. Nor is the classification of timber of veneers in successive layers aligned along the
into strength groups to be interpreted as preventing longitudinal (length) dimension of the composite.
the use of design data desired for a particular timber 2.1.11 Loaded Edge Distance — The distance
or grade of timber on the basis of reliable tests. measured from the centre to the edge towards which
the load induced by the connector acts, and the
2 TERMINOLOGY
unloaded edge distance is the one opposite to the loaded
2.0 For the purpose of this Section, the following edge.
definitions and those in accordance with accepted
2.1.12 Location — A term generally referred to as
standard [6-3A(1)], shall apply.
exact place where a timber is used in building.
2.1 Structural Purpose Definitions
2.1.13 Outside Location — Position in buildings in
2.1.1 Beam, Built-Up-Laminated — A beam made by which timbers are occasionally subjected to wetting
joining layers of timber together with mechanical and drying as in the case of open sheds and outdoor
fastenings, so that the grain of all layers is essentially exposed structures.
parallel.
2.1.14 Permissible Stress — Stress obtained by
2.1.2 Beam, Glued-Laminated — A beam made by applying factor of safety to the ultimate stress.
bonding layers of veneers or timber with an adhesive,
2.1.15 Sandwich, Structural — A layered construction
so that grain of all laminations is essentially parallel.
comprising a combination or relatively high-strength
2.1.3 Diaphragm, Structural — A structural element facing material intimately bonded to and acting
of large extent placed in a building as a wall, or roof, integrally with a low density core material.
and made use of to resist horizontal forces such as wind 2.1.16 Spaced Column — Two column sections
or earthquakes-acting parallel to its own plane. adequately connected together by glue, bolts, screws
2.1.4 Duration of Load — Period during which a or otherwise.
member or a complete structure is stressed as a 2.1.17 Structure, Permanent — Structural units in
consequence of the loads applied. timber which are constructed for a long duration and
2.1.5 Edge Distance — The distance measured wherein adequate protection and design measures have
perpendicular to grain from the centre of the connector initially been incorporated to render the structure
to the edge of the member. serviceable for the required life.

2.1.6 End Distance — The distance measured parallel 2.1.18 Structure, Temporaq — Structures which are
to grain of the member from the centre of the connector erected for a short period, such as hutments at project
to the closest end of timber. sites, for rehabilitation, temporary defence
constructions, exhibition structures, etc.
2.1.7 Finger Joint — Joint produced by connecting
timber members end-to-end by cutting profiles (tapered 2.1.19 Structural Element — The component timber
projections) in the form of V-shaped grooves to the members and joints which make up a resulting
ends of timber planks or scantlings to be joined, glueing structural assembly.
the interfaces and then mating the two ends together
2.1.20 Structural Grades — Grades defining the
under pressure.
maximum size of strength reducing natural
2.1.8 Fundamental or Ultimate Stress — The stress characteristics (knots, sloping grain, etc) deemed

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 5


permissible in any piece of structural timber within flat sawn surface caused by the separation or raising of
designated structural grade classification. wood fibres along the growth rings; C$ ‘Raised Grain’.

2.1.21 Structural Timber — Timber in which strength 2.2.12 Loose Knot — A knot that is not held firmly in
is related to the anticipated in-service use as a controlling place by growth or position, and that cannot be relied
factor in grading and selection and/or stiffness. upon to remain in place; c~ ‘Tight Knot’.

2.1.22 Termite — An insect of the order Isoptera 2.2.13 A40uld — A soft vegetative growth that forms
which may burrow in the wood or wood products of a on wood in damp, stagnant atmosphere. It is the least
building for food or shelter. harmful type of fungus, usually confined to the surface
of the wood.
2.1.23 Wet Location — Position in buildings in which
timbers are almost continuously damp or wet in contact 2.2.14 Pitch Pocket — Accumulation of resin between
with the earth or water, such as piles and timber growth rings of coniferous wood as seen on the cross
foundations. section.

2.2 Definitions of Defects in Timber 2.2.15 Sap Stain — Discoloration of the sapwood
mainly due to fungi.
2.2.1 Check — A separation of fibres extending along
the grain which is confined to one face of a piece of 2.2.16 Sapwood — The outer layer of log, which in
wood. the growing tree contain living cells and food material.
The sapwood is usually lighter in colour and is readily
2.2.2 Compression Wood — Abnormal wood which attacked by insects and fungi.
is formed on the lower sides of branches and inclined
stems of coniferous trees. It is darker and harder than 2.2.17 Shake — A partial or complete separation .---
normal wood but relatively low in strength for its between adjoining layers of tissues as seen in end
weight. It can be usually identified by wide eccentric surfaces.
growth rings with abnormally high proportion of 2.2.18 Slope of Grain — The inclination of the fibres
growth latewood. to the longitudinal axis of the member.
2.2.3 Dead Knot — A knot in which the layers of 2.2.19 Sound Knot — A tight knot free from decay,
annual growth are not completely intergrown with which is solid across its face, and at least as hard as
those of the adjacent wood. It is surrounded by pitch the surrounding wood.
or bark. The encasement may be partial or complete.
2.2.20 Split — A crack extending from one face of a
2.2.4 Decay or Rot — Disintegration of wood tissue piece of wood to another and mns along the grain of
caused by fungi (wood destroying) or other micro- the piece.
organisms.
2.2.21 Tight Knot — A knot so held by growth or
2.2.5 Decayed Knot — A knot softer than the position as to remain firm in position in the piece of
surrounding wood and containing decay. wood; C$ ‘Loose Knot’.
2.2.6 Diameter of Knot — The maximum distance 2.2.22 Wane — The original rounded surface of a tree
between the two points farthest apart on the periphery remaining on a piece of converted timber.
of a round knot, on the face on which it becomes
2.2.23 Warp — A deviation in sawn timber from a
visible. In the case of a spike or a splay knot, the
true plane surface or distortion due to stresses causing
maximum width of the knot visible on the face on
departure from a true plane.
which it appears shall be taken as its diameter.
2.2.24 Worm Holes — Cavities caused by worms.
2.2,7 Discoloration — A change from the normal
colour of the wood which does not impair the strength 3 SYMBOLS
of the wood.
3.1 For the purpose of this Section, the following letter
2.2.8 Knot — A branch base or limb embedded in the symbols shall have the meaning indicated against each:
tree or timber by natural growth. a= Projected area of bolt in main member
2.2.9 Knot Hole — A hole left as a result of the (t’ X d3), mm’
removal of a knot. B= Width of the beam, mm
2.2.10 Live Knot — A knot free from decay and other c= Concentrated load, N
defects, in which the fibres are firmly intergrown with D= Depth of beam, mm
those of the surrounding wood. Syn. ‘Integrown knot’; D, = Depth of beam at the notch, mm
cf. ‘Dead Knot’. D, = Depth of notch, mm
2.2.11 Loose Grain (Loosened Grain) — A defect on a d= Dimension of least side of column, mm

6 NATIONAL BUILDING CODE OF INDIA


d{ = Least overall width of box column, mm M= Maximum bending moment in beam,
d, = Least overall dimension of core in box N/mmz
column, mm N= Total number of bolts in the joint
d, = Diameter of bolt, mm n= Shank diameter of the nail, mm
d, = Bolt-diameter factor P= Load on bolt parallel to grain, N
e= Length of the notch measured along the P, = Ratio of the thickness of the compression
beam span from the inner edge of the support flange to the depth of the beam
to the farthest edge of the notch, mm Q. Statical moment of area above or below the
E= Modulus of elasticity in bending, N/mmz neutral axis about neutral axis, mm3
F= Load acting on a bolt at an angle to grain, N q = Constant for particular thickness of plank
.& = Calculated bending stress in extreme fibre, 9, = Ratio of the total thickness of web or webs
N/mmz to the overall width of the beam
& = Calculated average axial compressive R= Load on bolt perpendicular (normal) to
stress, N/mmz grain, N
fat = Calculated axial tensile stress, N/mmz s= Unsupported overall length of column, mm
f, = Permissible bending stress on the extreme t = Nominal thickness of planks used in
fibre, N/mmz forming box type column, mm
~= Permissible stress in axial compression, t’ = Thickness of main member, mm
N/mmz
u= Constant for a particular thickness of the
fcn = Permissible stress in compression normal plank
(perpendicular) to grain, N/mm’
v= Vertical end reaction or shear at a section, N
L, = Permissible stress in compression parallel
‘w = Total uniform load, N
to grain, N/mm*
~.. x = Distance from reaction to load, mm
Permissible compre~sive stress in the
direction of the line of action of the load, y= A factor determining the value of form
N/mmz factor K~
J= Permissible stress in tension parallel to 6= Deflection at middle of beam, mm
grain, N/mmz e= Angle of load to grain direction
H= Horizontal shear stress, N/mmz
z= Section modulus of beam, mm3
I= Moment of inertia of a section, mm4
a, = Percentage factor for t’/d3 ratio, parallel to
K= Coefficient in deflection depending upon grain
type and criticality of loading on beam
22 = Percentage factor for t’/d3 ratio, perpendicular
K1 = Modification factor for change in slope of to grain
grain
K, = Modification factor for change in duration 4 MATERIALS
of loadings
4.1 Species of Timber
K,,
The species of timber recommended for structural
K,,
purposes are given in Table 1.
K, = Form factors
.,
and 4.1.1 Grouping
K, Species of timber recommended for constructional
1
K, = Modification factor for bearing stress purposes are classified in three groups on the basis of
their strength properties, namely, modulus of elasticity
E
(E,) and extreme fibre stress in bending and tension
K, = Constant equal to 0.584 f
F T (f,).
The characteristics of these groups areas given below:

d
n UE
K9 = Constant equal to ~ 5q fw
Group A — E above 12.6 x 103 N/mmz and f,
above 18.0 N/mm*.
2.5E
K,O = Constant equal to 0.584 f Group B — E above 9.8 x 103 N/mm* and up
F v to 12.6 x 103 N/mm* and fbabove
L= Span of a beam or truss, mm 12.0 N/mmz and up to 18.0 N/mm*.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 7


Group C — E above 5.6 x 103 N/mm* and up 4.6.2.1 Prohibited defects
to 9.8 x 103 N/mmz and ~~ above
Loose grains, splits, compression wood in coniferous
8.5 N/mm* and up to 12.0 N/mm’.
species, heartwood rot, sap rot, crookedness, worm
NOTE — Modulus of elasticity given above is applicable holes made by powder post beetles and pitch pockets
for all locations and extreme fibre stress in bending is for
inside location.
shall not be permitted in all the three grades.
4.6.2.2 Permissible defects
4.1.2 Timber species may be identified in accordance
with good practice [6-3A(3)]. Defects to the extent specified in Table 8 shall be
permissible.
4.2 The general characteristics like durability and
treatability of the species are also given in Table 1. NOTE — Wanes are permitted provided they are not combined
with knots and the reduction in strength on account of the wanes
Species of timber other than those recommended in
is not more than the reduction with maximum allowable knots.
Table 1 may be used, provided the basic strength
properties are determined and found in accordance 4.6.3 Location of Defects
with 4.1.1.
The influence of defects in timber is different for
NOTE — For obtaining basic stress figures of the unlisted different locations in the structural element. Therefore,
species, reference may be made to the Forest Research Institute, these should be placed during construction in such a
Debra Dun.
way so that they do not have any adverse effect on the
4.3 The permissible lateral strength (in double shear) members, in accordance with good practice [6-3A(5)].
of mild steel wire shall be as given in Table 2 and
Table 3 for different species of timber. 4.7 Suitability

4.7.1 Suitability in Respect of Durability and


4.4 Moisture Content in Timber
TreatabilitjI for Permanent Structures
The permissible moisture content of timber for various
There are two choices as given in 4.7.1.1 and 4.7.1.2.
positions in buildings shall be as given in Table 4.
4.7.1.1 First choice
4.5 Sawn Timber
The species shall be any one of the following:
4.5.1 Sizes
a) Untreated heartwood of high durability.
Preferred cut sizes of timber for use in structural Heartwood if containing more than 15 percent
components shall be as given in Tables 5 to 7. sap wood, may need chemical treatment for
protection;
4.5.2 Tolerances
b) Treated heartwood of moderate and low
Permissible tolerances in measurements of cut sizes durability and class ‘a’ and class ‘b’
of structural timber shall be as follows: treatability;
c) Heartwood of moderate durability and class
a) For width and thickness:
‘c’ treatability after pressure impregnation, and
1) Up to and including 100 mm ~~ mm d) Sapwood of all classes of durability after
thorough treatment with preservative.
+6
2) Above 100 mm -3 ‘m 4.7.1.2 Second choice
+10 The species of timber shall be heartwood of moderate
b) For length
-Omm durability and class ‘d’ treatability.
4.6 Grading of Structural Timber 4.7.2 Choice of load-beting temporary structures or
semi-structural components at construction site
4.6.1 Cut sizes of structural timber shall be graded,
after seasoning, into three grades based on permissible a) Heartwood of low durability and class ‘e’
defects given in Table 8: treatability; or

a) Select Grade b) The species whose durability and/or treatability


is yet to be established, as listed in Table 1.
b) Grade I
c) Grade II 4.8 Fastenings

4.6.2 The prohibited defects given in 4.6.2.1 and All structural members shall be framed, anchored, tied
permissible defects given in 4.6.2.2 shall apply to and braced to develop the strength and rigidity
structural timber. necessary for the purposes for which they are used.

8 NATIONAL BUILDING CODE OF INDIA


Table 1 Safe Permissible Stresses for the Species of Timber
[Clauses 4.1,4 .2,4.7.2 (b), 5.4.1 ,5.4.2 and 6.5.8.3.1 (b)]

Species Locality Average’ Modsdus of Permissible Stress in N/mm* for Grade I Preservative Characters
/ - \ from Density at Elasticity --- - Y /
A
Y

Botanical Name Trade Name Where 12 percent (All Grades Bending and Shear Compression Compression ~Durability $Treat- $Refrac-
Tested Moistore and All Tension Along all Locations Parallel Perpendicular class ability teriness
Content Locations Grain, Extreme to Grain to Grain Grade to AU
x 103 Fibre Stress Seasoning
kg/m3 Nhmn2 ~~~ ~

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19)

GROUP A
Acacia catecthu Khair (KHA) U.P. 1009 13.44 20.1 16.8 13.4 1.6 2.2 13.8 12.3 10.1 7.7 6,0 4.9 I A
Acacia chundra Red kutch M,P. 1086 16.79 26.5 22.0 17.6 2.2 3.2 17.9 15.9 13.0 10.9 8.4 6.9 A
Albizia odoratissirna Kala siris (KSI) Chennai 737 13,54 18.7 i5.6 12.5 1.5 2.2 13.3 11.8 9.6 7.3 5.6 4.6 I e B
Bruguiera spp. Broguiera (BSV) Andmans 897 17,68 21.9 18.3 14.6 1.2 1.7 14.3 12.7 10.4 5.5 4.3 3.5 m
(Mangrove)
Grewia tiliijolia Dhaman (DHA) Cbennai 788 14.82 18.3 15.2 12.2 1.3 1.9 12.0 10.7 8.7 6,0 4.7 3.8 III d B
Hopea utilis Karnng Ch&mai 987 16.91 25.1 20.9 16.7 1.5 2.2 16.4 14.6 11.9 9.3 7.3 5.9 —
(Balana carpus utilis)
Hopeagkzbra Hopes (HOP) Chennai 1081 14.79 21.3 17.8 14.2 1.5 2.2 14.5 12.9 10.6 9.9 7.7 6.3 I — A
Hopea parvt>ra Hopes (HOP) Chennai 923 13.03 18.6 15.5 12.4 1.3 1.8 13.2 11.8 9.6 9.2 7.3 6.0 1 e A
.44anUotapolyandra (Syn. Piog (PIG) Assam 903 13.20 19.1 15.9 12.7 1.3 1.8 1.2 10.4 8.5 5.7 4.4 3.6 III b A
Cynometra polyandra)
IWesuaferrea Mesua (IvIES) . , Assam 965 16.30 23.3 19.4 15.5 1.2 1.8 15.5 13.8 11.3 5.9 4.6 3.7 I — A
MitrsusopsIittorqlis Bulle&woo&@IL) S. Andaman 1103 17.39 22.7 18.9 15.1 1.5 2.1 14.2 12.7 10.4 11.3 8.8 7.2 I — A
PeMo*earon imiicwo Ballagi (BAL) Chennai 1139 16.29 22.4 18.7 15.0 1.5 2.2 14.7 13.1 10.7 8.7 6.8 5.5 1 e A
PterocarpwS;amcdinus Red STttUb’S (MA) Chennai 1121 12.73 25.0 20.9 16.7 1.7 2.5 18,1 16.1 13.2 11.8 9.2 7.5 — — A
Sagawa ellipfiea Chooi fCOC) Andmatrs 869 15.06 21.5 17.9 14.3 1.1 1.5 12.5 11.1 9.1 5.3 4.1 3.4 — — A
Stereospernmncelonoides Padri (PAD) Chennai 731 12.94 19.0 15.8 12.7 1.1 1.6 11.9 10.6 8.7 4.0 3.1 2.6 III — B
Vitexaltissirna Miila (MIL) Msbarashtra 937 13.01 18.2 15.2 12.1 1.2 1.7 12.6 11.2 9.2 9.5 7.4 6.1 I e A

GROUP B
Albizzia lebbeck Kokko (KOK) Andaman 642 iL17 13.4 11.2 9.0 I.1 1.5 9.0 8.0’ 6.5 4.4 3.4 2.8 I e B
Table 1 — Continued

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19)

Anogeissus latifolia Dhaura, Axle wood U.P. 892 10.55 16.1 13.4 10.7 1.1 1.6 9.1 8.1 6.6 4.7 3.7 3.0 I e A
(AXL) (Baldi)
Artocaqws hirsulus Airri (m) Chennai 600 10.45 15.0 12.5 10.0 0.7 1.1 10.4 9.2 7.5 3.3 2.6 2.1 I — B
Acacia nilotica Babul (BAB) U.P. 797 — — 12.9 10.3 1.4 2.1 8.9 7.9 6.4 5.2 4.0 3.3 I b B
Acacia ferruginea Safed khsir ‘ Mahara.shtra 993 12.28 23.0 19.2 15.3 1.7 2.4 13.9 12.4 10.1 9.9 7.7 6.3 — —
Acrocaqnmfkin~olius Mundani (MUN) Chermsi 690 12.59 16.1 13.4 10.8 1.2 1.8 10.5 9.4 7.7 4.6 3.6 2.9 III c B
Agbio odulis Aglaia (AGL) Assam 815 12.56 18.2 15.2 12.1 1.4 2.0 10.1 8.9 7.3 4.4 3.4 2.8 — — A
Anogeisswr acuminota Yon Orissa 844 11.67 17.6 14.7 11.7 1.3 1.8 10.8 9.6 7.9 5.1 4.0 3.3 — — A
Atakmlia rnonophy[la Jungli-rrimbu (JHI) Orissa 897 10.31 16.7 13.9 11.1 1.5 2.1 11.3 10.0 8.2 6.3 4.9 4.0 — — —
Altingia excelsa Jutili (JUT) Assam 795 11.37 17.1 14.3 11.4 1.2 1.8 11.0 9.8 8.0 6.8 5.3 4.4 II e A
Amoora spp. Arnari (AMA) W. Bengal 625 1.05 13.4 1.1 9.2 0.9 1.3 8.4 7.4 6.0 3.7 2.9 2.4 II d B
Bucklandia popalnea (Syn Plpli (PIP) W. Bengal 672 9.89 12.8 10.7 8.6 1.1 1.5 7.9 7.0 5.7 3.5 2.7 2.2 m e c
Exbuck.kmdia populnea)
Cassiafistulo Amaltas (AMT) U.P. 865 11.80 19.2 16.0 12.8 1.4 2.0 12.3 10.9 8.9 7.2 5.6 4.6 I — A
Carallia lucida Maniawaga Assam 748 12.60 18.4 15.3 12.3 1.2 1.7 11.4 10.1 8.3 5.9 4.6 3.8 — —
Canarium .rtrictum Dhup Chennai 655 11.86 13.3 11.1 8.9 0.9 1.2 8.1 7.2 5.9 2.8 2.2 1.8 m c
Cassio sienea Kasod M.P. 820 10.50 15.4 12.8 10.9 1.0 1.4 10.8 9.6 7.9 5.5 4.3 3.5 — — —
Casuerina equisetifolio Casuarina (CAS) Orissa 769 11.44 14.6 i2.2 9.8 1.3 1.8 8.2 7.3 5.9 4.0 3.1 2.5 m e A
Celophyllam temculosum Peon (Poo) Maharashtra 657 9.77 13.4 11.2 9.0 0.8 1.1 8.6 7.7 6.3 2.8 2.2 1.8 JJ — B
Chkwoxylon swielem”a Satin wood (CFI) M.P. 865 11.69 18.2 15.1 12.1 1.4 2.0 10.9 9.7 8.0 6.3 4.9 4.0 m — A
Cullenio resayoano Kararri(IMP) Chermai 625 12.43 14.7 12.3 9.8 0.6 0.9 9.0 8.0 6.6 2.7 2.1 1.7 Ill b c
(Syn C. execelsa)
Diploknerna butyracea Hill mahua (Hh4A) S. Andaman 780 10.64 15.3 12.8 10.2 1.0 1.5 9.9 8.8 7.2 6.6 5.2 4.2 —
(Syn Bassio butyrance)
Dyscxylurn malebaricum White ceda (WCE) Chermai 745 10.92 13.2 11.0 8.8 1.0 1.4 8.0 7.1 5.8 3.1 2.4 1.9 I B
Dipterocarpus grandiflorus Gurjan (GUR) N. Andaman 758 11.71 12.5 10.5 8.4 0.8 1.1 7.9 7.1 5.8 2.7 2.1 1.7 I — B
Dipterocarpus rnacrocarpus Hollong @IQL) Assam 726 13.34 14.5 12.0 9.6 0.8 1.1 8.8 7.9 6.4 3.5 2.7 2.2 IJl a B
Dichopsispolyantha (Syn Tali CAL) Assam 734 11.24 14.9 12.4 10.0 1.1 1.6 9.9 8.8 7.2 4.7 3.7 3.0 — B
Palnquiumpolymtham)
Dichopsis eliiptica Pali (PAL) Chennai 606 11.86 13.9 11.6 9.3 0.7 1.0 8.5 7.5 6.2 2.9 2.2 1.8 I e B
(Syp Palaqaium eU@icum)
Dlospyros micmpylla Ebony (EBO) Maharashtra 776 12.15 14.2 11.9 9.5 0.9 1.3 8.3 7.3 6.0 3.3 2.6 2.1 — — A
Diospyros pyrrhocarpus Ebony (EBO) N. Andamsn 843 9.93 13.5 11.2 9.0 1.0 1.4 ,7.9 7.0 5.7 4.0 3.1 2.5 III — A
Diptemesrpus bourdilloni Gurjan (GUR) Kerala 699 12.71 13.6 11.3 9.0 0.7 1.0 7.8 6.9 5.7 2.5 1.9 1.6 — B
Eucalyptus J@bulus Eucalyptus Chermai 912 14.83 15.9 13.2 10.6 10.3 1.5 9.0 8.0 6.5 3.4 2.6 2.1 I e A
(Blue gum) (BLN)
Bucalyptns ougenioides Eucalyptus Chennsi 853 11.47 16.4 13.6 10.9 1.2 1.7 11.3 10.0 8.2 7.6 5.9 4.8 — — —

*--- --- ..-+


1— -’ ---
.

I I u

Ioa)lol I I I

w MM.
Ww I E!

Cawo,qc)w ~ *, w 0) o Cq P.
mocho-+ce m--mono
. . -.+.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 11


H
Table 1 — Continued

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19)

Terminalia citnna — Assam 755 11.89 17.1 14.3 11.4 1.1 1.6 10.8 9.6 7.9 5.0 3.9 3.2 — —
Terminalia rnanii Black-chuglam (BCH) S. Andatnarr 822 12.66 16.8 14.0 11.2 1.1 1.6 10.3 9.2 7.5 5.1 4.0 3.2 II a B
Tectona grandis Teak (TEA) U.P. 660 9.97 15.5 12.9 10.3 1.2 1.6 9.4 8.3 6.8 4.5 3.5 2.8 I e B
Terminalia paniculate Kindal(KIN) Maharashtra 765 10.57 13.1 10.9 8.7 0.9 1.3 8.6 7.7 6.3 3.6 2.8 2.3 I c A
Alreminalia alata Laurel (IAlJ), Sain Chennai 906 10.54 15.1 12.5 10.0 1.1 1.6 9.4 8.4 6.8 6.2 4.8 4.0 I b A
Terminalia bilata White-chuglarn (WCH) S. Andarnan 690 12.38 15.5 13.0 10.4 0.9 1.2 9.8 8.7 7.1 3.6 2.8 2.3 m e B
Thespesia populnea Bhendi (BHE) Maharashtra 766 10.36 18.9 15.8 12.6 1.3 1.9 11.3 10.0 8.2 4.4 3.4 2.8 — B
Xylia .xyIocarpa Irul (IRU) Maharashtra 839 11.63 16.2 13.5 10.8 1.3 1.8 10.9 9.7 7.9 7.8 6.0 4.9 I e A
Zanthoxylum budranga Mullilam (MUL) W. Bengal 587 10.65 14.7 12.2 9.8 0.9 1.2 9.5 8.4 6.9 3.4 2.6 2.1 I e B
Adina oligocephalo — Arunaehal 715 11.17 15.2 12.7 10.1 1.2 1.7 10.3 9.2 7.5 4.0 3.1 2.4 — — .
Castanopsis indica Chestnut Meghalaya 688 12.54 14.8 12.3 9.9 1.0 1.4 9.8 8.7 7.1 3.4 2.7 2.2 — — B
Eucalyptus citriodara Eucalyptus Nil&i 831 12.12 17.3 14.4 11.5 1.4 2.0 11.0 9.8 8.0 4.2 3.3 2.7 — — —
Eucalyptus cim’odata Eucalyptus Outy 725 9.35 15.4 12.9 10.3 1.0 1.4 8.6 7.6 6.3 3.0 2.4 2.0 — — —
Eucalytus tereticomis Eucalyptus Chennai 77’7 11.05 16.7 13.9 11.1 1.0 1.4 9.7 8.6 7.1 3.4 2.6 2.2 m e —

GROUP C
Tbizia procera Whte siris U.P. 643 9.02 13.4 11.2 8.9 1.0 1.4 8.5 7.6 6.2 4.3 3.3 2.7 I c B
Artocaqxts kakocha Lakooch (UK) U.P. 647 6.14 10.0 8.3 6.7 1.0 1.4 5.3 4.7 3.8 2.8 2.2 1.8 I — B
Artoca~us Iwtarophyllus Jack, kathrd (RAT) Chennai 617 9.46 13.9 11.6 9.2 1.0 1.5 9.3 8.3 6.8 4.5 3.5 2.9 I d B
(Syn. A. lntegnfilia)
Aphanamixispolyskzchya Pitraj (MT) West Bengal 668 8.98 12.3 10.2 8.2 1.1 1.5 8.0 7.1 5.8 4.0 3.1 2.6 I — B
(Syn. Anraora rehituka)
Adina cordifolia+ Haldu (HAL) 8.54 13.3 11.1 8.9 1.0 1.4 8.7 7.7 6.3 4.4 3.4 2.8 In a B
Anthocephyalus chinensis Kadam (w) 1.88 9.7 8.1 5.4 0.7 1.0 5.9 5.3 4.3 1.9 1.5 1.2 III a —
(SyrL A. Gw%anba)
Arlocaipus chaplasha Chaplash (cHP) -. 515 9.11 13.2 11.0 8.8 0.9 L2 8.5 7.5 6.2 3.6 2.8 2.3 III d B
Acacia Leacoph[oea Hiwar q . M.P. ‘ ’737 7.85 13.4 11.2 9.0 1.0 1.5 7.5 6.7 5.4 4.5 3.5 2.8 — — A
Acacia melanoxylone Black WOOd Chennai 630 9.45 13.0 10.8 8.7 1.1 L5 7.6 6.8 5.5 3.2 2.5 2.0 — — —
Acacia mearnsii Black wattle Chmnai 669 6.10 10.4 8.6 6.9 0.8 1.2 6.0 5.4 4.4 2.3 1.8 1.5 — — —
(Syn. A. mollissima)
Aecerspp. Ma@@4AP) Punjab, U.P. Ml 7.35 9.9 8.2 6.5 0.9 L3 5.5 4.9 4.0 2.1 1.7 1.4 III . B
A@a itW??@OS Bnel (BEL) U.P. WO 8.81 13.5 11.2 9.0 1.4 2.0 8=8 7.8 6.4 6.8 5.3 4.3 III — B
{S@. Itiia b@@
A&e/b.b@$a — Andarnan 705 9.16 13.2 11.0 8.8 1.1 1.5 7.9 7.1 5.8 4.0 3.1 2.6 — — —
Ailanthus grands Ookul (OOK) W. Bengal 404 7.94 8.3 6.9 5.5 Q.6 0.8 5.3 4.7 3.9 1.1 0.9 0.7 III — c
Anogeissus pe& Kardhai (KAH) U.P. 929 9.75 17.0 14.2 11.4 1.3 1.8 9.8 8.7 7.1 6.5 5.1 4.2 HI — A
Areca nut — Kerala 833 9.48 15.2 12.7 10.2 1.2 1.6 10.8 9.6 7.8 7.3 5.7 4.7 — — —

---k-- ....
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19)

Albizia lucida Amnachrd, 566 8.51 10.7 8.9 7.1 8.2 1.2 7.3 6.3 5.3 2.3 1.8 1.5 — —
A.P.
Azadirachta indica Neem (NEE) U.P. 836 8.52 14.6 12.1 9.7 1.3 1.8 10.0 8.9 7.3 5.o 3.9 3.2 — —
Boswellia seriata Salai (SAA) Bihar 551 7.21 9.4 7.9 6.3 0.7 1.1 5.5 4.9 4.0 2.1 1.6 1.3 I e c
Bridelia retusa Kassi (KAS) Bihar 584 9.42 11.6 9.7 7.7 0.9 1.3 7.1 6.3 5.1 4.0 3.1 2.6 I e B
Betula lnoides Birch (BIR) West Bengal 625 9.23 9.6 8.0 6.4 0.8 1.1 5.7 5.0 4.1 2.2 1.7 1.4 — — B.
Bischojia javanica Uriam Bishopwood Chermai 769 8.84 9.6 8.2 6.5 0.8 1.1 5.9 5.3 4.3 3.6 2.8 2.3 III — A

13urserra serrata Muntenga (MUR) A.P. 756 1.17 15.5 13.3 10.5 0.9 1.3 10.1 9.0 7.4 5.3 4.1 3.4 II c —
(Syn. Protium serratarn)
Careya arbersa Kumbi (KUM) U.P. 889, 8.37 13.1 10.9 8.8 1.0 1.5 7.7 6.8 5.6 5.3 4.1 3.4 I e A
Cedras deoalwu Deodar @m) H.P. 557 9.48 10.2 8.7 7.2 0.7 1.0 7.8 6.9 5.7 2.7 2.1 1.7 I c c
Cupressus torulosa cypress (CYP) U.P. 506 8.41 8.8 7.6 6.2 0.6 0.8 6.9 6.2 5.0 2.4 1.8 1.5 I e c
Castanopsis hystrix Indian chestnut West Bengal 624 9.85 10.6 8.8 7.0 0.8 1.2 6.4 5.7 4.6 2.7 2.1 1.7 II b B
(ICI-I)
Chukrasia vclutina Cbickrassy (cHI) West Bengal 666 8.35 11.8 9.8 7.9 1.1 1.5 7.1 6.3 5.2 3.9 3.1 2.5 II c B
(Syn. C. Tabularis)
Calophyllum wightianum Peon (IWO) Mabarashtra 689 8.68 13.5 11.2 9.0 1.0 1.4 8.7 7.8 6.4 4.0 3.1 2.5 It B
Canarium sm”ctum White dhup Assam 569 10.54 10.1 8.4 6.7 0.7 1.1 6.2 5.5 4.5 2.1 1.6 1.3 III — c
Chlorapkom excelsa —

Cacosnuc~era Ceconut (COC) Kerala 761 7.34 9.2 7.7 6.1 0.7 1.1 9.5 8.4 6.9 3.9 3.0 2.5 . — —

Da&q@ lat~olia Rosewood (ROS) M,P. 884 8.39 12.9 10.8 8.6 1.1 1.6 8.0 7.1 5.8 4.2 3.3 2.7 I — B
Dalbergia sissee Siaso (SIS) Punjab 799 7.14 12.8 10.7 8.5 1.3 1.8 8.2 7.3 6.0 4.2 3.3 2.7 I e B
Ditlemio Mica Dillenia (ML) West Bengal 617 8.61 12.1 10.0 8.0 0.8 1.2 7.3 6.5 5.3 2.7 2.1 1.7 m a B
Dillenia ptmtagyne Dillenia (ML) West Bengal 622 7.56 11.8 9.9 7.9 0.9 1.3 7.1 6.3 5.2 3.5 2.7 2.2 III d B
~spyres melanoxylon Ebony (EBO) 818 7.69 10.9 9.1 7.3 0.9 1.2 7.0 6.2 5.1 3.3 2.6 2.1 n . A
Duabanga gmnd#lom Lampati (LAP) West Bengal 485 8.38 9.8 8.2 6.5 0.6 0.9 6.4 5.7 4.7 1.8 1.4 1.1 m c c
(Syn. L? Sonrtemtioides)
Ele+arpus mbercukztas Rudrak (I&D) Chermai 466 8.74 9.7 8.1 6.4 0.7 1.0 6.3 5.6 4.6 2.0 1.5 1.3 — — c
&calyptMs kybrid Myaore gum (MGU) Chemai 753 6.00 10.2 8.5 6.8 0.9 1.2 7.3 6.5 5.3 4.0 3.1 2.5 Ill e —
Cal&W #tombaiden — Chennai 607 6.48 9.2 7.7 6.1 0.7 1.0 6.9 6.1 5.0 4.0 3.1 2.6 — — —
{* l%ne$a Awnboidea)
Garugapinnata Gamga(GAU) U.P. 571 7.58 11.7 9.7 7.8 1.0 1.5 7.2 6.4 5.3 3.4 2.6 2.1 I e B
gGmdbIe anborea Gamari (GAM) U.P. 501 7.02 9.8 8.2 6.6 0.8 1.2 5.7 5.0 4.1 4.2 3.2 2.7 I e B
Gardenia .WJWJ Gardenia (GAI) M.P. 705 7.13 14.1 11.7 9.4 1.2 1.7 8.4 7.4 6.1 4.6 3.6 3.0 . . —
Har&wicki3 binati Al@ (AIW) M.P. 852 6.64 14.1 11,8 9.4 1.3 1.8 9.0 8.0 6.5 7.4 5.6 4.7 I e —
Hehpteka integrifolia Kanju (KAN) U.P. 592 7.46 12.0 10.0 8.0 0.9 1.3 6.7 6.0 4.9 2.8 2.2 1.8 m b B
Table 1 — Continued

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19)

Heterrophragma rexburghii Palang (PAL) M.P. 616 8.69 12.3 10.2 8.2 0.7 1.0 7.9 7.0 5.7 3.4 2.6 2.1 — —
Juglans Spp. walnut (wAL) U.P. 565 9.00 9.9 8.3 6.6 0.9 1.2 5.8 5.2 4.2 2.2 1.7 1.4 III — B
Lagerstrosmia speciosa Jsnd (JAAR) N. Andsman 622 8.53 12.1 10.1 8.1 0.8 1.8 7.7 6.8 5.6 3.4 2.6 2.2 II e B
(Syn. L. jlesregihal)
L4znnea grandis Jhingan (JHI) U.P. 557 5.63 8.5 7.1 5.7 0.6 0.9 4.9 4.4 3.6 2.2 1.7 1.4 m e B
(Syn. L.coromandelica)
Leucanena leucocephda Subabul (SWB) U.P. 673 6.32 11.6 9.7 7.8 1.0 1.5 7.4 6.6 5.4 3.8 3.0 2.4 — —
Lophopatalum wightianum Bsnati (BAN) Chennai 460 7.33 8.5 7.5 5.6 0.5 0.8 5.3 4.7 3.8 1.8 1.4 1.1 III . c
Madhuca longvolia varlatifolia Mahua (MAu) M.P. 936 8.82 13.0 10.8 8.7 1.0 1.4 7.5 6.7 5.5 6.3 4.9 4.0 I e A
(Syn. Bassia hzt$olia)
Mangifera indica Mango, Aam (MAN) Orissa 661 9.12 12.2 10.2 8.2 1.0 1.4 7.3 6.5 5.3 3.1 2.4 2.0 III a c
Machilus macrantha Machilus (MAC) Chennai 521 7.63 10.2 8.5 6.8 0.7 1.0 6.3 5.6 4.6 2.4 1.9 1.5 III e B
Mallotus philippinensis Raini (RAI) U.P. 662 7.51 10.8 9.0 7.2 1.0 1.4 6.0 5.4 4.4 2.9 2.3 1.8 m — B
Manglietia insignia — Assam 449 10.37 10.9 9.1 7.3 0.7 1.0 8.0 7.1 5.8 3.4 2.6 2.1 . — —
Michelia montana Champ (CHM) West Bengal 512 8.25 10.9 9.1 7.3 0.7 1.0 6.6 5.9 4.8 2.8 2.2 1.8 I — B
Mitragyna pervifolia Kaim (KM) U.P. 651 7.82 12.6 10.5 8.4 1.0 1.5 7.9 7.0 5.7 3.7 2.9 2.4 Lu b B
(Syn. Stephagyneperv#olia)
Michelia excelsa Champ (CHM) West Bengal 513 10.12 9.8 8.2 6.5 0.7 1.0 6.1 5.5 4.5 1.6 1.3 1.0 Jl e B
Miliusa velutnia Domsal (DOM) U.P. 747 7.92 11.7 9.7 7.8 1.1 1.6 7.0 6.3 5.1 3.7 2.9 2.4 JJl — —
Morus alba Muhrry (MUL) U.P. 743 8.20 11.8 9.8 7.9 1.0 1.4 6.6 5.8 4.8 3.8 2.9 2.4 JI — B
Morus serrata Mulberry (MUL) H.P. 657 7.03 10.2 8.5 6.8 0.9 1,3 5.6 5.0 4.1 2.6 2.0 1.6 m — B
Morus Iaevigaiw Bela (BOL) Atldaman 588 8.61 12.3 10.2 8.2 1.0 1.5 7.2 6.4 5.3 3.3 2.5 2.1 — — B
Oageinia eejeinensis Sandan (SAD) M.P. 784 8.54 13.3 11.1 8.9 1.2 “1.7 8.5 7.5 6.2 5.1 3.9 3.2 I — B
(Syn. O. delbergioides)
z
Phoebe hainesiana Booaunt (BOH) 566 9.50 13.2 11.0 8.8 0.8 1.2 8.8 7.8 6.4 2.8 2.1 1.8 JJ c B
$’ 9.82
Pinus rwburghii Cbir (CHR) U.P. 525 8.5 7.3 6.0 0.6 0.9 6.0 5.3 4.4 2.0 1.5 1.3 m b c
z (Sym P. iong~olia)
* “R /
1? Pinus wallichiana Kail (KAL) 515 .6.80 6.6 5.6 5.0 0.6 0.8 5.2 4.6 3.8 1.7 1.3 1.0 n c c
Phoebe goalperansis Bonsum(J30H) AsSapl 511 7.65 9.7 8.1 6.5 0i7 1.0 6.6 5.9 4.8 2.2 1.7 1.4 II c B
5 Parretiopsis jocquementiena Rohu,Parcntia H.P. 761 5.77 12.5 10.4 8.3 1.2 1.7 6.8 6.1 5.0 4.0 3.1 2.5 III — B
~ Pinas kesia Khaaipine (KIT) North East 513 7.38 8.9 7.4 5.9 0.6 0.7 5.8 5.2 4.3 1.5 1.2 1.0 III a B
o (Sym Pinus insularis)
n
o Pistacia integepima Kikar Singhi J&K 881 7.32 13.1 10.9 8.7 1.2 1.7 8,0 7.1 5.8 4.3 3.4 2.8 — — —
g
Podocaqn4s nem~olins Thittim) s. Andaman 533 9.41 12.5 10.4 .8.3 6.1 0.9 8.0 7.1 5.8 2.6 2.0 1.6 II — —
g PolyaWaJ%agrances DebdatU (DEB) Maharashtrs 752 9.15 11.9 9.9 7.9 0.8 1.2 6.7 6.0 4.9 3.0 2.3 1.9 m —
(Nedunar)
% Polyalthia coreoides M.P. 7W 9.29 13.2 11.0 8.8 1.0 1.4 7.1 6.3 5.2 3.2 2.5 2.0 — —
s

/ m
1
---.=...
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19)

Prunus napeulensis Ampati West Bengal 548 9.41 104.4 8.7 69.6 0.9 1.2 6.7 6.0 4.9 2.4 1.9 1.6 — — —
Pterespernrum acer@Olium Hattipaila (HAT) West Bengal 607 9.55 13.5 11.3 9.0 0.9 1.2 8,7 7.7 6.3 3.2 2,5 2.0 III c B
Qucrcus spp. oak North East 657 11.65 11.4 9.5 7.6 0.8 1.2 6.7 5.9 4.8 2.0 1.6 1.3 u c B
Raderomachera xyloca~e Vedankonnai Chennai 696 8.52 13.2 11.0 8.8 1.1 1.5 9.0 8.0 6.6 4.3 3.3 2.7 II a —
(Syn. Sterosperam xylocarparn)
Schleichera oleosa Kusum (KUS) Bihar 1032 12.12 15.5 13.0 10.4 1.5 2.1 10.9 9.7 7.9 6.1 4.2 3.9 II a A
(Syn. S. trijuga)
Schima wallichii Cbilauni (CHL) West Bengal 693 9.57 11.1 9.3 7.4 0.9 1.3 6.6 5.9 4.8 2.3 1.8 1.4 m d B
Shotea assamica Mskai (MAK) Assam 548 9.27 11.1 9.2 7.4 0.9 1.3 7.1 6.3 5.2 2.9 2.2 1.8 III c B
Sonneralia apetale Keora (KEO) West Bengal 617 8.63 12.8 10.7 8.5 0.9 1.3 7.4 6.6 5.4 4.8 3.7 3.0 II — B
Stereospermum suaveokms Padri (PAD) U.P. 721 8.86 13.3 11.1 8.9 0.9 1.3 7.3 7.0 5.7 3.5 2.7 2.2 III — B
Tactona grandis Teak (TEA) M.P. 617 8.49 12.8 10.7 8.5 0.8 1.3 7.9 7.0 5.7 4.0 3.1 2.6 1 e B
Terminalia aq”una Arjun (ARJ) Bihar 794 7.71 12.2 10.2 8.2 1.1 1.6 7.4 6.6 5.4 5.2 4.1 3.3 II b B
Terrninalia myriocarpa Hollock (HOC) Assam 615 9.62 11.9 9.9 8.0 0.9 1.2 7.6 6.7 5.5 2.9 2.2 1.8 III a B
Terrrrinalia procera White bombwae N.Andarnan 626 8.99 11.8 9.8 7.9 0.9 1.3 7.2 6.4 5.3 3.0 2.3 1.9 Ill b B
(WBO)
Tams buccata Yew (YEW) West Bengal 705 7.79 14.3 11.9 9.5 1.2 1.7 8.7 7.8 6.4 4.7 3.7 3.0 — — —
Tamarinds indica Imli (IML) Chennai 913 5.63 11.4 9.5 7.6 1.2 1.7 7.0 6.2 5.1 5.3 4.1 3.4 — — B
Toena ciliata Toon (TOO) U.P. 487 6.40 8.7 7.3 5.8 0.7 1.0 5.4 4.8 3.9 2.4 1.8 1.5 II c B
Vateria indica Vellapine (VEL) Chermai 535 10.95 11.5 9.6 7.6 0.7 1.1 7.5 6.7 5.5 2.3 1.8 1.4 III e c
Aeculas indica Horae chesmut U.P. 484 7.55 8.5 7.1 5.7 0.8 1.1 4.8 4.2 3.5 1.8 1.4 1.1 — — B
(HCH)
Borassus~el@er Tad (Paimyra) A.P. 838 8.79 10.5 8.8 7.0 0.7 1.0 10.0 8.8 7.2 4.7 3.6 2.7 — — —
(TAD)
Eucalyptus cemaldidensis Eucalyptus Karostaka 804 9.53 12.8 10.6 8.5 0.8 1.1 7.2 6.4 5.2 3.5 2.7 2.2 — — A
Eucalyptus canrakfulenis Eucalyptus U.P. 781 7.03 12.4 10.4 8.3 1.1 1.6 7.9 7.0 5.7 3.5 2.8 2.3 — — A
Eucalyptus pilukaria Eucalyptus . T.N. 713 9.22 14.8 12.3 11.1 1.0 1.4 8.5 7.6 6.2 2.8 2.2 1.8 — — A
Eucalyptus propingus Eucaly~”* T.N. 584 7.93 12.8 10.7 8.5 0.8 1.2 8.0 5.4 4.4 2.5 1.9 1.6 — — A
Eucalyptus saligna Eucalyptus U.P. 819 8.24 11.5 9.6 7.6 1.5 2.1 8.2 7.3 6.0 6.2 4.8 4.0 — — A

* Species thus marked sod tested from other localities show bigher strength to enable their categorisation in higher group.
For Example
i) Sal tested from West Beng~ Bihar, U.P. attd Assam can be classified as Grurrp ‘A’ q.weies;
ii) Haldu tested from Bihar cao be claasiikd as Gruup ‘B’ species;
iii) Morus Iaevigate (Bole) of Assam can be classi%d in Group ‘B’ species.
& Table 1 — Concluded

t Classification for preservation based on durability tests, etc.


class
I – Average life more than 120 months;
II – Average life 60 months and above bnt less than 120 months; and
III – Average life less than 60 months.
$ Treatability Grades
a - Heartwood easily treatablq
b - Heartwood treatable, but complete penetration not always ntrtaind, in case where the least dimension is more than 60 mm;
c - Heartwood only partially treatable;
d – Herrrtwoodrefractory to treatment; and
e – Heartwood very refractory to treatment, penetration of preservative being practicablynil even from the ends;
Data based on strength properties at three years of age of tree.
$ Classifications based on seasoning behaviour of timber and refractoriness w.r.t. cracking, spliting and drybrg rate:
A – Highly refracto~ (slow and difficulty to season free from surface and end cracking);
B – Moderately refractory (maybe seasoned free from surface and end cracking within reasonably short periods, given a little protection against rapid drying conditions); and
C – Non-refractory maybe rapidly seasoned free from surface and end-cracking even in the open air and sun. If not rapidly dried, they develop blne stain and mould on the surface.
Table 2 Permissible Lateral Strengths (in Double Shear) of Nails 3.55 mm Dia, 80 mm Long
(Clawse 4.3)

s] Species of Wood For Permanent Construction For Temporary Structures


No. Strength per Nail Strength per Nail (for Both
/ A._.
~ Lengthening Joints and
Botanical Name Trade Name Lengthening Node Joints)
Joints Joints
Nx 102 N X 102 N X 102
(1) (2) (3) (4) (5) (6)

i, Albies pirdrow’) Fir 8 2 12


-) Babul 15
L. ,4cacia nilotica 11 34
‘3 Acrocnrpus fraxin(folius Mundani 18 9.5 19.5
i: Adina cordifolia Haldu 23.5 10 22
-.:,.
Albizia lebbeck Kokko 20 7 24
6. .41bizia odoratissima Kala Siris 14 5 22
7. Anogeissus latfolia Axlewood 20 10 29
Y.
< Aphanamixis polystachya Pitraj 19 9 19
9. Calophyllum spp. ~) Peon 16 9 21
10. Canarium euphyllum White dhup 9 8 10.5
Il. Cbstanopsis spp. Indian chestnut 18 10,5 23.5
j~ C’edrus deodara~) Deodw 9 4 15
13. Chukrasia tabularis Chikrassy 24 8 27
14. Cinnamomum spp. ~) Cinnomon 12 9 13
15. Cupressus torulosa Cypress 6 5 18
16. Dipterocarpus macro carpus Hollong 17 7 20
17. Dipterocarpus spp. Gurjan 19 9 19
18. Dillenia pertagyna Dillenia 16.5 12 16
19. Diospyros melanoxylon Ebony 26.5 10 30.5
20. Eucalyptus eugenioides Eucalyptus 17 10 30
21. Grewia tilijolia’) Dhaman 13 5 24
22. Lugers troemia spp. Jarul 24.5 21.5 22.5
23. Hopea parviflora Hopea 31.5 13 28.5
24. I.ugerstroemia spp. ~) Lendi 19 5 26
25, Mangifera indica Mango 11 9 16
26. Maniltoa polyandra Ping 26 23.5 32
27. Mesua ferrea Mesua 26 8 41
28. Michelia spp. Champ 13 9 20
29. Millingtonia spp.’) — 10.5 6 17
30. Morus alba Mulberry 13 10.5 22.5
31. Melia azedarach Persian lilac (bakain) 10.5 2.5 9
32. (lugeinia oojeinensis Sandan 17 11 18
33. Phoebe spp. ~) Bonsum 12 6 13
34. Pinus roxburghii~’ Chir 11 10 16
35. Pin us wallichiana’ ) Kail 7 3 9
36. Pterocarpus marsupium Bijasal 15 12 27
37. Pterocarpus dalbergiodes Pauduak 19 14 23
.38. Planchonia andarnanica Red bombwe 14 13 29
?9. Quercus .spp. Oak 11 11 27
40. Scheichera cleosa Kusum 23 16 40
41. Shorea roubusta Sal (M. P.) 23 15,5 19.5
42. Shores robusta Sal 10 5 19
43. Sterwspenmurn Padriwood 16 8 19.5
44. Syzygium spp. Jamum 15 12 25
45. Tectona grandis Teak 14 8 13
46. Terminalia Bellirica Bahera 10 10 14
47. Terminalia biolata White chuglam 18 9 21
48. Terminalia procera Badam 18 10.5 20
49. Terrninalia manii~) Black chuglam 23 10 33
50. Terminalia myriocarpa Hollock 13 10 19
51. Terminalia alata Sain 16 16 29
52. Toona spp. Toona 10 8 21
53. Xylia x.ylacarpa Irul 23 6 33
54. Toona ciliata Toon 16 9 21

NOTES
1 Nails of 3.55 mm diameter are most commonly used. The above values can also be used for 4 mm diameter 100 mm long naiIs.
2 The values in N are approximate converted values from kgf. For exact conversion the value is 1 kgf = 9.80665 N.
—
1)Species requiring no prebonng for nail penetration.

PART 6 STRUCTURAL. DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 17


Table 3 Permissible Lateral Strengths (in Double Shear) of Nails 5.00 mm Dia,
125 mm and 150 mm Long
(Clause 4.3)

S1 Species of Wood For Permanent Construction For Temporary Structures


No. Strength per Nail Strength per Nail (for
r- A_ #- A Both Lengthening Joints
Y
Botanical Name Trade Name Lengthening Joints Node Joints and Node Joints)
Nx 102 N X 102 N X 102
(1) (2) (3) (4) (5) (6)

1. Abies pindrow’) Fir 16.5 4.5 21


Y
2. Acacia catechu Khai r 42 25 71.5
3 Acacia nilotica’) Babul 27 13.5 53
i: Alibizia procera Safed siris 35 18 —
5. Alibizia odoratissima~) Kala siris 27.5 17.5 45
6. Alstonia scholaris Chatian 9.5 5.5 27
7. Anogeissus latfolia Axlewood 22.5 13 46.5
8. Cupressus torulosa Cypress 20 7 27
9. Cullenia rosayroana Karani 11 9.5 30
10. Dalbergia sissoo Sissoo 17 15 43
11. Diptrocarous spp. Gurjan 19.5 9.5 33
12. Hardwickia binata Anjan 32 19 59
13. Hopea perviflora Hopea 60.5 25 61.5
14 Holoptelea integrifolia Kanju 18 12.5 37.5
15. Mangijera indica’) Mango 22.5 15 32
16. Mesua ferrea Mesua 24 15.5 57.5
17. Michelia champaca’) Champ 26 12.5 39
18. Pterocarpus marsupium Bijmal 20.5 15 43
19. Pinus roxburghii~) Chir 9 6 24
20. Shorea robusta (U. P.) Sal 19.5 17 37
21. Shorea robusta Sal 30.5 20 41
22. Schleichera cleosa Kusum 15 14 55
23. Stereospimum personatum Padriwood 22 8 34
24. Sy.zygium cumini Jamum 18 14,5 38.5
25. lerminalia myriocarpa Hollock 27.5 9 41
26. Tectona ,grandis Teak 28 13 30
27. Hopea utilis Karung kangoo 31 10 58
28. Phoebe spp ‘) Bonsum 20 7.5 30

NOTES
1 Nails of 5.00 mm diameter are most commonly used.
2 The values in N are approximate converted values from kgf. For exact conversion the value is 1 kgf = 9.80665 N.

‘) Species requires no preboring for nail penetration.

Table 4 Permissible Percentage Moisture Content Values


/
(Clause 4.4)

S1 Use Zones (see Note)


No. / L -
I II III IV
(1) (2) (3) (4) (5) (6)

i) Structural elements 12 14 17 20
ii) Doors and windows
a) 50 mm and above in thickness 10 12 14 16
b) Thinner than 50 mm 8 10 12 14
iii) Flooring strips for general purposes 8 10 10 12
iv) Flooring strips for tea gardens 12 12 14 16

NOTE — The country has been broadly divided into the following four zones based on the humidity variations in the country:
Zone I — Average annual relative humidity less than 40 percent.
Zone II — Average annual relative humidity 40 to 50 percent.
Zone III — Average annual relative humidity 50 to 67 percent.
Zone IV — Average annual relative humidity more than 67 percent.

For detailed zonal classification, tolerances, etc reference may be made to good practice [6-3A(4)].

18 NATIONAL BUILDING CODE OF INDIA

..
Table 5 Preferred Cut Sizes of Structural Timbers for Roof Trusses
(Span from 3 m to 20 m)
(Clause 4.5. 1)

Thickness W]dth
mm mm

(1) (2) (3) (4) (5) (6) (7) (8) (9)

20 40 50 60 80 I(I!I — — —
25 40 50 60 80 1(M3 120 140 160
30 40 50 60 80 100 120 140 160
35 — 60 80 160 120 140 160
40 — 60 80 .100 120 140 160
50 — 60 80 100 120 140 160
60 — — — 80 1(XI 120 140 160
80 — — — — 100 120 140 160

NOTES
1 For truss spans marginally above 20 m, preferred cut sizes of structural timber may be allowed.
2 Preferred lengths of timhec 1, 1.5,2,2.5 and 3 m.
w

Table 6 Preferred Cut Sizes of Structural Timber for Roof Purlins,


Rafters, Floor Beams, Etc
(Clause 4.5.1)

Thickness Width
mm mm
/
(1) (2) (3) (4) (5) (6) (7) (8)

50 80 100 120 140 — — —


60 80 100 120 140 160 — —
80 — 100 120 ’140 160 — —
100 — — — 140 160 180 2Wl

NOTE — Preferred lengths of timber: 1.5,2,2.5 and 3 m.

Table 7 Preferred Cut Sizes of Structural Timbers for Partition


Framing and Covering, and for Centering
(Clause 4.5. 1)

Thickness Width
mm mm
A
(1) (2) (3) (4) (5) (6) (7)

10 40 50 60 80 — — — — —
15 40 50 60 80 100 — — — —
20 40 50 60 80 100 120 160 200 —
25 40 50 60 80 100 120 1(XI 200 240
30 40 50 60 80 100 120 160 200 240
40 40 — 60 80 1(X3 120 160 200 240
50 — 50 — 80 100 120 160 200 240
60 — — 60 80 103 120 160 2tXl 240
80 — — 80 100 120 160 200 240

NOTE — Preferred lengths of timbec 0.5, 1, 1.5,2,2.5 and 3 m.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO 3A TIMBER 19


Table 8 Permissible Defects for Cut Sizes of Timber for Structural Use
(Clauses 4.6.1 and 4.6.2.2)
All dimensions in millimetres.

S1 Defects Select Grade Grade I Grade 11


No.

(1) (2) (3) (4) (5)

i) Wane Shall be permissible at its deepest Shall be permissible at its deepest Shall be permissible at its deepest
portion up to a limit of 1/8 of the portion up to a limit of 1/6 of the portion up to a limit of 1/4 of the
width of the surface on which it width of the surface on which it width of the surface on which it
occurs occurs occurs

u) Worm holes Other than those due to powder Other than those due to powder Other than those due to powder post
post beetles are permissible post beetles are permissible beetles are permissible

iii) Slope of grain Shall not be more than 1 in 20 Shall not be more than 1 in 15 Shall not be more than 1 in 12

iv) Live knots:

Widthof Permissible Maximum Size of Permissible Maximum Size of Permissible Maximum Size of
Wide Faces Live Knot on Live Knot on Live Knot on
OfCut Size2 ~~
of Timber Narrow faces and Remaining Narrow faces and Remaining Narrow faces and Remaining central
1A of the width central half of % of the width central half of 1A of the width half of the width
Max face close to the width of the face close to the width of the face close to of the wide faces
edges of cut size wide faces edges of cut size wide faces edges of cut size
of timber of timber of timber
(1) (2) (3) (4) (5) (6) (7)

75 10 10 19 19 29 30
100 13 13 25 25 38 39
150 19 19 38 38 57 57
200 22 25 44 50 66 75
250 25 29 50 57 66 87
300 27 38 54 75 81 114
350 29 41 57 81 87 123
400 32 44 63 87 96 132
450 33 47 66 93 99 141
500 35 50 69 100 105 150
550 36 52 72 103 108 156
600 38 53 75 106 114 159

V) Checks and shakes:

Width of the Face of Permissible Depth Permissible Depth Permissible Depth


the Timber Max Max Max
Max

(1) (2) (3) (4)

75 12 25 36
100 18 35 54
150 25 50 75
200” 33 65 99
250 40 81 120
300 50 100 150
350 57 115 171
400 66 131 198
450 76 150 225
500 83 165 249
550 90 181 270
600 100 200 300

20 NATIONAL BUILDING CODE OF INDIA


Allowable stresses or loads on joints and fasteners shall 5.3 The permissible stresses (excepting E) given in
be determined in accordance with recognized Table 9 shall be multiplied by the following factors to
principles. Common mechanical fastenings are of bar obtain the permissible stresses for other grades
type such as nails and spikes, wood screws and bolts, provided that the conditions laid down in 5.2 are
and timber connectors including metallic rings or satisfied:
wooden disc-dowels. Chemical fastenings include
a) For Select Grade Timber 1.16
synthetic adhesives for structural applications.
b) For Grade II Timber 0.84
5 PERMISSIBLE STRESSES
5.3.1 When low durability timbers are to be used
5.1 Fundamental stress values of different groups of [see 5.2(b)] on outside locations, the permissible
timber are determined on small clear specimen stresses for all grades of timber, arrived at by 5.2
according to good practice [6-3A( 1)]. These values are and 5.3 shall be multiplied by 0.80.
then divided by the appropriate factors of safety to
obtain the permissible stresses. In these values, are then 5.4 Moditlcation Factors for Permissible Stresses
applied, appropriate safety factors given in the relevant 5.4.1 Due to Change in Slope of Grain
table of the accepted standard [6-3A(5)] to obtain the
permissible stress. When the timber has not been graded and has major
defects like slope of grain, knots and checks or shakes
5.2 The permissible stresses for Groups A, B and C but not beyond permissible value, the permissible stress
for different locations applicable to Grade I structural given in Table 1 shall be multiplied by modification
timber shall be as given in Table 9 provided that the factor K, for different slopes of grain as given in
following conditions are satisfied: Table 10.
a) The timbers should be of high or moderate
Table 10 Modifications Factor K1 to Allow
durability and be given the suitable treatment
for Change in Slope of Grain
where necessary.
(Clause 5.4.1)
b) Timber of low durability shall be used after
proper preservative treatment to good practice slope Modification Factor KI
*
[6-3A(6)], and . / -%
Strength of Beams, Strength of
c) The loads should be continuous and Joists and Ties Posts or Columns
permanent and not of impact type. (1) (2) (3)

Table 9 Minimum Permissible Stress Limits 1 in 10 0.80 0.74


1 in 12 0.90 0.82
(N/mm2) in Three Groups of Structural Timbers 1 in 14 0.98 0.87
(for Grade I Material) 1 in 15 and fla~ 1.00 1,00
(Clauses 5.2 and 5.3) NOTE — For intermediary slopes of grains, values of
modification factor may be obtained by interpolation.
S1 Strength Location of Group Group Group
No. Character Use A B c
5.4.2 Due to Duration of Load
(1) (2) (3) (4) (5) (6)

i) Bending and Inside 1) 18.0 12.0 8.5 For different durations of design load, the permissible
tension along stresses given in Table 1 shall be multiplied by the
grain modification factor Kz given in Table 11.
ii) Shear *) All locations 1.05 0.64 0.49
Horizontal NOTE — The strength properties of timber under load are time-
dependent. ,,
Along grain All locations 15 0.91 0.70 /
iii) Compression Inside 1) 11.7 7.8 4.9 Table 11 Modifications Factor Jfa, for Change
parallel to grain
in Duratiou of Loading
iv) Compression Inside 1) 4.0 2.5 1.1
perpendicular (C/ause 5,4.2)
to grain
Duration of Loading Modiieation Factor K2
V) Modulus of All locations 12.6 9.8 5.6
elasticity and grade (1) (2)
(x 103N/mm’)
Continuous (Normal) “1.0
1) For~or~ng stresses for other lWations of use, that is, outside Two months 1.15
and wet, ge~erally factors of 5/6 and 2/3 are applied. Seven days 1.25
Z)The values of horizontal shear to be used only for beams. In ~1 Wind and earthquake 1.33
other cases shear along grain to be used. Instantaneous or impact 2.00

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 21


T-

5.4.2.1 The factor Kz is applicable to modulus of the prebored hole shall not be taken into account for
elasticity when used to design timber columns, this purpose.
otherwise they do not apply thereto.
6.3.2 The net section used in calculating load carrying
5.4.2.2 If there are several duration of loads (in capacity of a member shall be at least net section
addition to the continuous) to be considered, the determined as above by passing a plane or a series of
modification factor shall be based on the shortest connected planes transversely through the members.
duration load in the combination, that is, the one
6.3.3 Notches shall be in no case remove more than
yielding the largest increase in the permissible stresses,
one quarter of the section.
provided the designed section is found adequate for a
combination of other larger duration loads. 6.3.4 In the design of an intermediate or a long column,
gross sectionshall be used in calculating load carrying
[Explanation: In any structural timber design for dead
capacity of the column.
loads, snow loads and wind or earthquake forces,
members may be designed on the basis of total of 6.4 Loads
stresses due to dead, snow and wind loads using
Kz = 1.33, factor for the permissible stress (of Table 1) 6.4.1 The loads shall conform to those given in Part 6
to accommodate the wind load, that is, the shortest of ‘S~ctural Design, Section 1 Loads, Forces and Effects’.’
duration and giving the largest increase in the 6.4.2 The worst combination and location of loads
permissible stresses. The section thus found is checked shall be considered for design. Wind and seismic forces
to meet the requirements based on dead loads alone shall not be considered to act simultaneously.
with modification Kz = 1.00].
6.5 Flexural Members
5.4.2.3 Modification factor Kz shall also be applied to
allowable loads for mechanical fasteners in design of 6.5.1 Such structural members shall be investigated
joints, when the wood and not the strength of metal for the following:
determines the load capacity.
a) Bending strength,
6 DESIGN CONSIDERATIONS b) Maximum horizontal shear,
6.1 All structural members, assemblies or framework c) Stress at the bearings, and
in a building, in combination with the floors, walls and d) Deflection.
other structural parts of the building shall be capable
6.5.2 Effective Span
of sustaining, with due stability and stiffness the whole
dead and imposed loadings as per Part 6 ‘Structural The effective span of beams and other flexural
Design, Section 1 Loads, Forces and Effects’, without members shall be taken as the distance from face of
exceeding the limits of relevant stresses specified in supports plus one-half of the required length of bearing
this Section. at each end except that for continuous beams and joists
the span may be measured from centre of bearing at
6.2 Buildings shall be designed for all dead and
those supports over which the beam is continuous.
imposed loads or forces assumed to come upon them
during construction or use, including uplifts or 6.5.3 Usual formula for flexural strength shall apply
horizontal forces from wind and forces from in design:
earthquakes or other loadings. Structural members and
their connections shall be proportioned to provide a
sound and stable structure with adequate strength and
stiffness. Wooden components in construction 6.5.4 Form Factors for FIFxural A4embers
generally include panels for sheathing and diaphragms,
siding, beams, girder, columns, light framings, The following form factors shall be applied to the
masonry wall and joist construction, heavy-frames, bending stress:
glued laminated structural members, structural a) Rectangular Section — For rectangular
sandwiches, prefabricated panels, lamella arches, portal sections, for different depths of beams, the
frames and other auxiliary constructions. form factor Kg shall be taken as:
6.3 Net Section
D’+ 89400
6.3.1 The net section is obtained by deducting from K, = 0.81
the gross sectional area of timber the projected area of D2+55000
[1
all material removed by boring, grooving or other NOTE — Form factor (K,) shatt not be applied for hearns having
means at critical plane. In case of nailing, the area of depth less than or equrd to 300 rrrrn.

22 NATIONAL BUILDING CODE OF INDIA


b) Box Beams and I-Beams — For box beams
and I-beams, the form factor KA shall be
obtained by using the formula:

‘4=””8+”8’[D$:::) I SQUARE NOTCH


@OllOM SIDE NOTCHED)
where
d) For notched at upper (compression) face,
y= p; (6–8pl+ 3p:) (l–ql)+q, where e > D:

c) Solid Circular Cross-Sections — For solid 3V


H=—
circular cross sections the form factor KS shall 2 bD1
be taken as 1.18.
1- e -1
d) Square Cross-Sections — For square cross-
I
sections where the load is in the direction of
I
diagonal, the form factor KG shall be taken I m
as 1.414. I
a L ----- -
i
6.5.5 Width n
The minimum width of the beam or any flexural ? I
member shall not be less than 50 mm or 1/50 of the 1 SPLAYED NOTCH
(UPPER SIDE NOTCHED)
span, whichever is greater.
e) For notched at upper (compression) face,
6.5.6 Depth
where e c D:
The depth of beam or any flexural member shall not
be taken more than three times of its width without 3V
H=
lateral stiffening.

6.5.6.1 Stiffening [01


2bD–~e

All flexural members having a depth exceeding three 6.5.7.2 For concentrated loads:
times its width or a span exceeding 50 times its width
v = 1OC(Z–X) (x/D)’
or both shall be laterally restrained from twisting or
buckling and the distance between such restraints shall 9Z[2+(x/D)2]
not exceed 50 times its width.
and for uniformly distributed loads,
6.5.7 Shear

6.5.7.1 The following formulae shall apply:

a) The maximum horizontal shear, when the load After arriving at the value of V, its value will be
on a beam moves from the support towards substituted in the formula:
the centre of the span, and the load is at a
distance of three to four times the depth of
H==
the beam from the support, shall be calculated Ib
from the following general formula:
6.5.7.3 In determining the vertical reaction V, the
~=~
following deductions in loads maybe made:
Ib
a) Consideration shall be given to the possible
b) For rectangular beams: distribution of load to adjacent parallel beams,
3V if any;
H=—
2 bD b) All uniformly distributed loads within a
distance equal to the depth of the beam from
c) For notched beams, with tension notch at the edge of the~earest support may be
supports (see 6.5.7.3): neglected except in case of beam hanging
3 VD downwards from a particular suppo~, and
H=—
2 bD; c) All concentrated loads in the vicinity of the

PART 6 STRUCTURAL DESIGN — SECTION 3’ TIMBER AND BAMBOO: 3A TIMBER 23


supports may be reduced by the reduction 6.5.8.3 Bearing stress
factor applicable according to Table 12.
6.5.8.3.1 Length and position of bearing
Table 12 Reduction Factor for Concentrated a) At any bearing on the side grain of timber,
Loads in the Vicinity of Supports the permissible stress in compression
[Clause 6.5.7.3 (c)] perpendicular to the grain, fCn, is dependent
on the length and position of the bearing.
Distance of Load LSD 2D 2.5 D 3D
from the Nearest or More b) The permissible stresses given in Table 1 for
Support L compression perpendicular to the grain are
(1) (2) (3) (4) (5) also the permissible stresses for any length at
the ends of a member and for bearings
Reduction factor 0.60 0.40 0.20 No
reduction 150 mm or more in length at any other
position.
NOTE — For intermediate distances, factor maybe obtained
by linear interpolation. c) For bearings less than 150 mm in length
located 75 mm or more from the end of a
6.5.7.4 Unless the local stress is calculated and found member as shown in Fig. 1, the permissible
to be within the permissible stress, flexural member stress may be multiplied by the modification
shall not be cut, notched or bored except as follows: factor K, given in Table 13.
d) No allowance need be made for the difference
a) Notches may be cut in the top or bottom
in intensity of the bearing stress due to
neither deeper than one-fifth of the depth of
bending of a beam.
the beam nor farther from the edge of the
support than one-sixth of the span; e) The bearing area should be calculated as the
net area after allowance for the amount of
b) Holes not larger in diameter than one quarter
wane.
of the depth maybe bored in the middle third
of the depth and length; and f) For bearings stress under a washer or a small
plate, the same coefficient specified in
c) If holes or notches occur at a distance greater
Table 13 may be taken for a bearing with a
than three times the depth of the member from
length equal to the diameter of the washer or
the edge of the nearest support, the net
the width of the small plate.
remaining depth shall be used in determining
the bending strength. g) When the direction of stress is at angle to the
direction of the grain in any structural
I + NET I member, then the permissible bearing stress
I i DEPTH I
in that member shall be calculated by the
following formula:
fq x fc”
fce =
fq sin20 + f,n COS20
NOTCHED BEAMS
6.5.9 Deflection
6.5.8 Bearing
The deflection in the case of all flexural members
6.5.8.1 The ends of flexural members shall be supporting brittle materials like gypsum ceilings,
supported in recesses which provide adequate slates, tiles and asbestos sheets shall not exceed 1/360
ventilation to prevent dry rot and shall not be enclosed. of the span. The deflection,,@ the case of other flexural
Flexural members except roof timbers which are members shall not exceed 1./240 of the span and 1/150
supported directly on masonry or concrete shall have of the freely hanging length in the case of cantilevers.
a length of bearing of not less than 75 mm. Members
6.5.9.1 Usual formula for deflection shall apply:
supported on corbels, offsets and roof timbers on a
wall shall bear immediately on and be fixed to wall-
KWL3
plate not less than 75 mm x 40 mm. 6= ~ (ignoring deflection due to shear strain)

6.5.8.2 Timber joists or floor planks shall not be


supported on the top flange of steel beams unless the K-values =1/3 for cantilevers with load at free
bearing stress, calculated on the net bearing as shaped end,
to fit the beam, is less than the permissible compressive 1/8 for cantilevers with uniformly
stress perpendicular to the grain. distributed load,

24 NATIONAL BUILDING CODE OF INDIA


Table 13 Modification Factor K, for Bearing Stresses

(Clause 6.5.8.3.1)

Length of Bearing, in mm 15 25 40 50 75 100 150 or more


Moditlcation Factor, K7 1.67 1.40 1.25 1.20 1.13 1.10 1.00

1
75 mm_ 150 mm max
L
min ‘BEARING —

FIG. 1 POSITION OF END BEARINGS

1/48 for beams supported at both ends 6.6.1.2 For intermediate columns, the permissible
with point load at centre, and compressive stress is calculated by using the following
5/384 for beams supported at both formula:
ends with uniformly distributed
load.

6.5.9.2 In order to allow the effect of long duration


loading on E, for checking deflection in case of beams
6.6.1.3 For long columns, the permissible compressive
and joists the effective loads shall be twice the dead
stress shall be calculated by using the following
load if timber is initially dry.
formula:
6.5.9.3 Self weight of beam shall be considered in
0.329 E
design. fc. —
(Sld)2
6.6 Columns
6.6.1.4 In case of solid columns of timber, S/d ratio
NOTE — The formulae given are for columns with pin end
conditions and the length shall be modified suitably with other shall not exceed 50.
end conditions.
6.6.1.5 The permissible load on a column of circular
6.6.1 Solid Columns cross-section shall not exceed that permitted for
Solid columns shall be classified into short, a square column of an equivalent cross-sectional
intermediate and long columns depending upon their area.
slenderness ratio (S\d) as follows: 6.6.1.6 For determining S/d ratio of a tapered column,
a) Short columns — where Sld does not exceed its least dimension shall be taken as the sum of the
11. corresponding least dimensions at the small end of the
column and one-third of the difference between this
b) Intermediate columns — where Sld is between
least dimension at the small end and the corresponding
11 and K8, and
least dimension at the large end, but in no case shall
c) Long columns — where S/d is greater than
the least dimension for the column be taken as more
K,.
than one and a half times the least dimension at the
6.6.1.1 For short columns, the permissible small end. The induced stress at the small end of the
compressive stress shall be calculated as follows: tapered column shall not exceed the permissible
f. =&p compressive stress in the direction of grain.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 25


‘p

4
6.6.2 Built-up Columns

6.6.2.1 Box column

Box columns shall be classified into short, intermediate


6.6.3.3
fc.
[01
fcp 1-:

For long spaced columns,


&
10

the formula shall +4


and long columns as follows:
be:
a) Short columns — where is less
2 0.329 EX2.5
& f==
than 8; 2

(S/d)2
b) Intermediate columns — where is
2 6.6.3.4 For individual members of spaced columns,
between 8 and Kg; and & 2
S/d ratio shall not exceed 80.
c) Long columns — where ~ is greater 6.6.4 Compression members shall not be notched.
than K,. & 2 When it is necessary to pass services through such a
member, this shall be effected by means of a bored
6.6.2.2 For short columns, the permissible hole provided that the local stress is calculated and
compressive stress shall be calculated as follows: found to be within the permissible stress specified. The
&= m, distance from the edge of the hole to the edge of the
member shall not be less than one quarter of width of
6.6.2.3 For intermediate columns, the permissible the face.
compressive stress shall be obtained using the
-.-
following formula 6.7 Structural Members Subject to Bending and
Axial Stresses

fc=9.tp[qk,J-&--J] 6.7.1 Structural members subjected both to bending


and axial compression shall be designed to comply with
the following formula:

6.6.2.4 For long columns, the permissible compressive ~+ h is not greater than 1.
stress shall be calculated by using the following f. f,
formula: 6.7.2 Structural members subjected both to bending
and axial tension shall be designed to comply with the
0.329 UE
f,= following formula:
2

2 ~ +~ is not greater than 1.


[1& 2 L f,
6.6.2.5 The following values of U and q, depending 7 DESIGN OF COMMON STEEL WIRE NAIL
upon plank thickness (t)in 6.6.2.3 and 6.6.2.4, shall JOINTS
be used:
7.1 General
t u 9
Nail jointed timber construction is suitable for light
mm
and medium timber framings (trusses, etc) up to 15 m
25 0.80 1.00
spans. With the facilities of readily available materials
50 0.60 1.00 and simpler workmanship in mono-chord and split
chord constructions, this type of fabrication has a large
6.6.3 Spaced Columns scope.
6.6.3.1 The formulae for solid columns as specified 7.2 Dimensions of Members
in 6.6.1 are applicable to spaced columns with a
restraint factor of 2.5 or 3, depending upon distances 7.2.1 The dimension of art individual piece of timber
of end connectors in the column. (that is, any single member) shall be within the range
given below:
NOTE — A restrained factor of 2.5 for location of centroid
group of fasteners at S/20 from end and 3 for location at S/10 a) The minimum thickness of the main members
to S/20 from end shall be taken. in mono-chord construction shall be 30 mm.
6.6.3.2 For intermediate spaced column, the b) The minimum thickness of an individual piece
permissible compressive stress shall be: of members in split-chord construction shall

26 NATIONAL BUILDING CODE OF INDIA


be 20 mm for web members and 25 mm for at right angle and as in Fig. 4 where the members are
chord members. inclined to one another at angles other than 90° and
c) The space between two adjacent pieces of subjected to either pure compression or pure tension.
timbe~ shall be restricted to a maximum of
7.6 Penetration of Nails
3 times the thickness of the individual piece
of timber of the chord member. In case of web 7.6.1 For a lap joint when the nails are driven from
members, it may be greater for joining the side of the thinner member, the length of penetration
facilities. of nails in the thicker member shall be one and a half
times the thickness of the thinner member subject to
7,3 No lengthening joint shall preferably be located
maximum of the thickness of the thicker member.
at a panel point. Generally not more than two, but
preferably one, lengthening joint shall be permitted 7.6.2 For butt joints the nails shall be driven through
between the two panel points of the members. the entire thickness of the joint.

7.4 Specification and Diameter of Nails 7.7 Design Considerations


7.4.1 The nails used for timber joints shall conform 7.7.1 Where a number of nails are used in a joint,
to Part 5 ‘Building Materials’. The nails shall be the allowable load in lateral resistance shall be the
diamond pointed. sum of the allowable loads for the individual nails,
7.4.2 The diameter of nail shall be within the limits of provided that the centroid of the group of these nails
one-eleventh to one-sixth of the least thickness of lies on the axis of the member and the spacings
members being connected. conform to 7.5. Where a large number of nails are to
be provided at a joint, they should be so arranged
7.4.3 Where the nails are exposed to be saline that there are more of rows rather than more number
conditions, common wire nails shall be galvanized. of nails in a row.
7.5 Arrangement of Nails in the Joints 7.7.2 Nails shall, as far as practicable, be arranged so
The end distances, edge distances and spacings of nails that the line of force in a member passes through the
in a nailed joint should be such as to avoid undue centroid of the group of nails. Where this is not
splitting of the wood and shall not be less than those practicable, allowance shall be made for any
given in 7.5.1 and 7.5.2. eccentricity in computing the maximum load on the
fixing nails as well as the loads and bending moment
7.5.1 Lengthening Joints in the member.
The requirement of spacing of nails in a lengthening 7.7.3 Adjacent nails shall preferably be driven from
joint shall be as follows (see also Fig. 2): opposite faces, that is, the nails are driven alternatively
from either face of joint.
S1 Spacing of Nails Type of Requirement,
No. Stress in the Min 7.7.4 For a rigid joint, a minimum of 2 nails for nodal
Joint joints and 4 nails for lengthening joint shall be
(1) (2) (3) (4) driven.

i) End distance Tension 12 n 7.7.5 Two nails in a horizontal row are better than
Compression 10 n using the same number of nails in a vertical row.
ii) In direction of Tension 10 n
grain Compression 5n 7.8 Special Considerati~n in Nail-Jointed Truss
iii) Edge distance — 5n Construction
iv) Between row of — 5n 7.8.1 The initial upward camber provided at the centre
nails perpendicular
of the lower chord of nail-jointed timber trusses shall
to the grain
be not less than 1/200 of the effective span for timber
NOTES structures using seasoned wood and 1/100 for
1 n is shank diameter of nails. unseasoned or partially seasoned wood.
2 The 5 n distance between rows perpendicular to the grain
may be increased subject to the availability of width of the 7.8.2 The total combined thickness of the gusset or
member keeping edge distance constant. splice plates on either side of the joint in a mono-chord
type construction shall not be less than one and a half
7.5.2 Node Joints times the thickness of the main members subject to a
The requirement for spacing of nails in node joints minimum thickness of 25 mm of individual gusset
shall be as specified in Fig. 3 where the members are plate.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 27


5n

EFFECTIVE END
DISTANCE, 10n min —D I

1 I I I I 1 I I
I I I I I I I I 1 1

1 I
I I I
J
!
I I I I I I I I

2A MONOCHORD TYPE BUTT JOINT SUBJECT TO COMPRESSION

IL EFFECTIVE END
DISTANCE, 5n min

I I II I
1 I I I I
1

[
I
I
, I *
I 1 I , I
I
I I I

n = SHANK DIAMETER OF NAIL

2B MONOCHORD TYPE BUTT JOINT SUBJECT TO TENSION

FIG. 2 SPACING OF NAILS IN ALENGHTHENINGJOINT — Continued

NATIONAL BUILDING CODE OF INDIA

..
I I I I I I I I
I t
II101
I I I I ,,, I I I,
1 I
I
I
1111
,,, ,
11111
,,, , I

\ 1 /

1 I 1 I I 1 I 1 I I
I I I I I I I I

5rl 5n
EFFECTIVE END
DISTANCE, 10n min 10n min

1
5n mln
6
5n$in
Qoeo ~ eeee
5n+mln
4943430 ~ O@@@
5n+mln
49666 ~ 66436
, 5n min
t
~ EFFEc~vE END

DISTANCE, 5n min

2C SPLIT - CHORD TYPE BUTT JOINT SUBJECT TO COMPRESSION

I 1 I I I I I I
I t
1 I 1 1 1
# I I I I
1 I 1
1 1 1 1 I 1 I I I

I I I I I
I I , 1 I

- EFFECTIVEEND
n . SHANKDIAMETEROF NAIL DISTANCE, 5n mln

2D SPLIT - CHORD TYPE BUl_f JOINT SUBJECT TO TENSION

FIG. 2 SPACING OF NAILS IN A LENGTHENING JOINT

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 29


L

5n min 5n min
UNLOADED LOADED
EDGE EDGE
~
I : 1
II
II \ t 1
I1 @ ~n
1

3A I 3B

II

I
I

II
:
10n
;
:1 :
I

n = SHANK DIAMETER OF NAIL


*5n MAYBE INCREASED TO 10n, IF THE DESIGNED WIDTH OF
CORD MEMBER PERMITS. OTHERWISE THE END OF THE LOADED
WEB MEMBER MAY BE EXTENDED BY 5n min

3C

FIG. 3 SPACING OF NAILS WHEREMEMBERS ARE AT


RIGHT ANGLES TO ONE ANOTHER

30 NATIONAL BUILDING CODE OF INDIA

..
. —.”——.. .

t -<

d LOADED

I
I II

I
I I Ion
I I

# I

4A / L.Lo-
EDGE
4B

+“s”
I I 1

i
I I
r
I J LBO~OM
CHORD

4C
*% MAYBE INCREASED TO 10n, IF THE DESIGNED WIDTH OF CHORD MEMBER PERMITS.
OTHERWISE THE END OF THE LOADED WEB MEMBER MAYBE EXKNDED BY 5n min
n = SHANK DIAMETER OF ML

FIG. 4 SPACING OF NAILS AT NODE JOINTSWHEREMEMBERS ARE


INCLINEDTO ONE ANOTHER

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 31


NOTES maximum depth and length of planks shall be limited
1 The allowable load or lateral strength values of nails shall be to 250 mm and 2000 mm, respectively.
lhose as given in Table 13.
2 The strength data for joints given in the section apply to gusset 8.2.3 In order to obtain the overall width of the beam,
or splice or fish plates of solid wood; however, materials other the number and thickness of planks to form vertical
than solid wood may be used for gusset when field tests are
nailed laminated beams, and also type and size of wire
made and their strength requirements have been established.
nail shall be as mentioned in Table 14. The protruding
7.8.3 The total combined thickness of all spacer blocks portion of the nail shall be cut off or clenched across
or plates or both including outer splice plates, at any the grains.
joint in a split-chord type construction shall not be less
than one and a half times the total thickness of all the 8.3 Design Considerations
main members at that joint. 8.3.1 Nail laminated beams shall be designed in
7.9 Fabrication accordance with 6.

The fabrication of nail-jointed timber construction shall 8.3.1.1 The deflection in the case of nailed laminated
be done in accordance with good practice [6-3A(7)]. timber beams, joists, purlins, battens and other flexural
members supporting brittle materials like gypsum,
8 DESIGN OF NAIL LAMINATED TIMBER ceiling slates, tiles and asbestos sheets shall not exceed
BEAMS 1/480 of the span. The deflection in case of other
8.1 Method of Arrangement flexural members shall not exceed 1/360 of the span
in the case of beams and joists, and 1/225 of the freely
8.1.1 The beam is made up of 20 mm to 30 mm thick
hanging length in case of cantilevers.
planks placed vertically with joints staggered in the
adjoining planks with a minimum distance of 300 mm. 8.3.2 Permissible lateral strength of mild steel wire
The planks are laminated with the help of wire nails at nails shall be as given in Table 2 and Table 3 for Indian
regular intervals to take up horizontal shear developed Species of timber, which shall apply to nails that have
in the beam besides keeping the planks in position their points cut flush with the faces. For nails clenched
(see Fig. 5). across the grains the strength may be increased by 20
percent over the values for nails with points cut flush.
8.1.2 The advantage in laminations lies in dimensional
stability, dispersal of defects and better structural 8.3.3 Arrangement of Nails
performance.
8.3.3.1 A minimum number of four nails in a vertical
8.2 Sizes of Planks and Beams row at regular interval not exceeding 75 mm to take
up horizontal shear as well as to keep the planks in
8.2.1 The plank thickness for fabrication of nailed
position shall be used. Near the joints of the planks
laminated beams recommended are 20,25 and 30 mm.
this distance may, however, be limited to 5 cm instead
8.2.2 In case of nailed laminated timber beam the of 75 mm.

Table 14 Number and Size of Planks and Nails for Nailed Laminated Beams
(Clause 8.2.3)

S1 Overall Width of Beam No. of Planks Thickness of Each Plank Type and Size of Nail to be Used
No. mm mm mm
(1) (2) (3) (4) (5)

i) 50 2 25 80 long 3.55 dia


ii) 60 3 20 -do-
iii) 70 3 (2X 25) -do-
(1 x 20)
iv) 80 4 20 100 long 4.0 dia
v) 90 3 30 -do-
vi) 100 4 25 125 long 5.0 dia
vii) 110 4 (3x 30) -do-
(1X20)
viii) 120 4 30 -do-
ix) 150 5 30 150 long 5.0 dia

NOTE — A number of combinations Of the different thickness Ofplanks may be adopted as long as the minimum and maximum
thickness of the planks are adhered to.

32 NATIONAL BUILDING CODE OF INDIA


800 1600 , 1600 .
400 1600 1600 , 400 .
L =
0
!-
●
!-
0 w
n R n
—

I
4@75mm = 300mm
\ 25 mm THICK TIMBER PLANKS

25

‘:.:::: ::::
. . . . . . . . .
— — — — —. — — . _
w I

25
— 25 CAMBER

All dimensions in millimetres.

FIG. 5 PLAN AND ELEVATIONOFA TYPICAL NAILED LAMINATEDTIMBERBEAM


8.3.3.2 Shear shall be calculated at various points of and economy in construction. Bolt jointed construction
Ihe beam and [he number of nails required shall be units offer better facilities as regards to workshop ease,
wconlmodated within the distance equal to the depth mass production of components, transport convenience
(~~[he beam, with a minimum of 4 nails in a row at a and re-assembly at site of work particularly in defence
s~,.ndartl spacing as shown in Fig. 6. sector for high altitudes and far off situations.
Designing is mainly influenced by the species, size of

-r
bolts, moisture conditions and the inclination of
01
N,
+ + +
loadings to the grains. In principle bolted joints follow

E
0
04
+ + +
the pattern of rivetted joints in steel structures.
0 0
ON
+ + +
o
m
9.2 Design Considerations
+ += +
o
mt
9.2.1 Bolted timber construction shall be designed in
H---L. 50 75 75
.-l accordance with 6. The concept of critical section, that
6A FOR 3.55 mm AND 4 mm DIAMETER NAILS is, the net section obtained by deducting the projected
area of bolt-holes from the cross-sectional area of
member is very important for the successful design
and economy in timber.
\ +----l + -1- +
1J
u 9.2.2 Bolt Bearing Strength of Wood

E 5
-1- + +
10
cN
, The allowable load for a bolt in a joint consisting of
+ +- +
two members (single shear) shall be taken as one half
- + + +
the allowable loads calculated for a three member joint
1 -1 I \
(double sheai) for the same t’/d3 ratio. The percentage
t of safe working compressive stress of timber on bolted
50 75 75
-1 “ 1 joints for different t’/d3 ratios shall be as given in
Table 15.
6B FOR 5 mm DIAMETER NAILS
Table 15 Percentage of Safe Working
All dimensions in millimetres.
Compressive Stress of Timber for Bolted
FIG. 6 STANDARD LENGTHWISESPACINGIN Joints in Double Shear
NAILED LAMINATED BEAM (Clause 9.2.2)

8.3.3.3 If the depth of the beam is more, then the t’ld3 Ratio Stress Percentage
vertical intermediate spacing of nails may be increased
Parallel to Grain Perpendicular to Grain
proportionately.
A, &
8.3.3.4 If the nails required at a point are more than (1) (2) (3)
th:~t can be accommodated in a row, then these shall
1.0 100 100
he provided lengthwise of the beam within the distance 1.5 100 96
equal to the depth of the beam at standard lengthwise 2.0 100 88
spacing. 2.5 100 80
3.0 100 72
8.3.3.5 For nailed laminated beam minimum depth 3.5 100 66
of 100 mm for 3.55 mm and 4 mm diameter nails, 4.0 96 60
4.5 90 56
and 125 mm for 5 mm diameter nails shall be provided. 5.0 80 52
5.5 72 49
8.4 I%brication 6.0 65 46
6.5 58 43 *
8.4.1 The Fabrication of nailed laminated timber beams 7.0 52 40
shall be done in accordance with good practice 7.5 46 39
[6-3A(8)]. 8.0 40 38
8.5 36 36
9 DESIGN OF BOLTED CONSTRUCTION 9.0 34 34
9.5 32 33
JOINTS 10.0 30 31
10.5 — 31
9.1 General —
11.0 30
11.5 — 30
Bolted joints suit the requirements of prefabrication
12.0 — 28
in small and medium span timber structures for speed

34 NATIONAL BUILDING CODE OF INDIA


9.2.2.1 Where a number of bolts are used in a joint, b) Spacing Between Rows of Bolts
the allowable loads shall be the sum of the allowable 1) For perpendicular to grain loading —
loads for the individual bolts. 2.5 d, to 5 d~ (2.5 d, for t’ld, ratio of 2
and 5 dq for t’ld~ ratio of 6 or more. For
9.2.2.2 The factors for different bolt diameter used in
ratios between 2 to 6 the spacing shall be
calculating safe bearing stress perpendicular to grain
obtained by interpolation.
in the joint shall be as given in Table 16.
2) For parallel to grain loading — At least
Table 16 Bolt Diameter Factor (N- 4) d, with a minimum of 2.5 d,. Also
(Clause 9.2.2,2) governed by net area at critical section
which should be 80 percent of the total
S1No. Diameter of Bolt Diameter
area in bearing under all bolts.
mm Factor (dJ
(1) (2) (3) c) End Distance — 7d~ for soft woods in tension,
5 d~ for hardwoods in tension and 4 d~ for all
i) 6 5.70
ii) 10 3.60 species in compression.
iii) 12 3.35 d) Edge Distance
iv) 16 3.15
3.05
1) For parallel to grain loading 1.5 d, or half
v) 20
vi) 22 3.00 the distance between rows of bolts,
vii) 25 2.90 whichever is greater.
2) For perpendicular to grain loading,
9.2.3 Dimensions of Members (loaded edge distance) shall be at least
a) The minimum thickness of the main member 4 d,.
in mono-chord construction shall be 40 mm.
9.3.2 For inclined members, the spacing given above
b) The minimum thickness of side members shall for perpendicular and parallel to grain of wood may
be 20 mm and shall be half the thickness of be used as a guide and bolts arranged at the joint with
main members. respect to loading direction.
c) The minimum individual thickness of spaced
9.3.3 The bolts shall be arranged in such a manner so
member in split-chord construction shall be
as to pass the centre of resistance of bolts through the
20 mm and 25 mm for webs and chord
inter-section of the gravity axis of the members.
members respectively.
9.3.4 Staggering of bolts shall be avoided as far as
9.2.4 Bolts and Bolting
possible in case of members loaded parallel to grain
a) The diameter of bolt in the main member shall of wood. For loads acting perpendicular to grain of
be so chosen to give larger slenderness (t’/d,) wood, staggering is preferable to avoid splitting due
ratio of bolt. to weather effects.
b) There shall be more number of small diameter
9.3.5 Bolting
bolts rather than small number of large
diameter bolts in a joint. The bolt holes shall be bored or drilled perpendicular
c) A minimum of two bolts for nodal joints and to the surface involved. Forcible driving of the bolts
four bolts for lengthening joints shall be shall be avoided which may cause cracking or splitting
provided. of members. A bolt hole of 1.0 mm oversize may be
d) There shall be more number of rows rather used as a guide for preboring.
than more bolts in a row. 9.3.5.1 Bolts shall be tightened after one year of
e) The bolt holes shall be of such diameter that completion of structure ahd subsequently at an interval
the bolt can be driven easily. of two to three years.
f) Washers shall be used between the head of
bolt and wood surface as also between the nut 9.4 Outline for Design of Bolted Joints
and wood. Allowable load on one bolt (unit bearing stress) in a
9.3 Arrangement of Bolts joint with wooden splice plates shall not be greater
than value of P, R, F as determined by one of the
9.3.1 The following spacings in bolted joints shall be following equations:
followed (see Fig. 7):
a) For Loads Parallel to Grain
a) Spacing of Bolts in a Row — For parallel and
perpendicular to grain loading= 4 d~ P= fCPa Ll

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 35


WASHE

NUT

UNLOADED
EDGE

I
I Ill
1 1 1 1
26 min. ‘--
+ -e e
—
ill Ill
4d3
Ill 111

+ -e e
1 46~

t LOADED
EDGE

1.6d3mln —-~ P 1.5d3min

‘2.5 d3far Ud3 RATlO 2


5 d3for Vd3 RATIO 6

7A SPACING OF BOLTS IN LENGTHENING JOINTS


---
(JOINTS LOADED PARALLEL TO GRAIN)

2d3min.

t UNLOADED
EDGE

1.5d3min ~ ~ 1 - 1.6d3min

‘2.5 d@r Vda RATIO 2


5 d3f@tRi3 RATfO 6

7B SPACING OF BOLTS AT NODE JOINTS

FIG. 7 TYPICAL SPACINGOF BOLTS IN STRUCTURALJOINTS

36 NATIONAL BUILDING CODE OF INDIA


b) For Loads Perpendicular to Grain The thickness of main member shall be at least 57 mm
and that of side member 38 mm with length and width
R=fc. al, df, of members governed by placement of connector at
c) For Loads at an Angle to Grain joint.

The metallic connector shall be so placed that the


PR
F= loaded edge distance is not less than the diameter of
Psin20 -t R c0s2e the connector and the end distance not less than 1.75
times the diameter on the loaded side.
9.5 Fabrication

The fabrication of bolt jointed construction shall be in 10.1.2 Design Considerations


accordance with good practice [6-3A(9)]. Figure 8 illustrates the primary stresses in a split ring
connector joint under tension. The shaded areas
10 DESIGN OF TIMBER CONNECTOR JOINTS
represent the part of wood in shear, compression and
10.1 In large span structures, the members have to tension. Related formulae for the same are indicated
transmit very heavy stresses requiring stronger jointing in Fig. 8.
techniques with metallic rings or wooden disc-dowels.
For fabrication of structural members, a hole of the
Improvised metallic ring connector is a split circular
required size of the bolt is drilled into the member and
band of steel made from mild steel pipes. This is placed
a groove is made on the contact faces of the joint.
in the grooves cut into the contact faces of the timber
members to be joined, the assembly being held together Theoretical safe loads in design shall be corroborated
by means of a connecting bolt. with sample tests done in accordance with good
practice [6-3(10)].
10.1.1 Dimensions of Members
NOTE — A pilot study on determinationof strength of ring
Variation of thickness of central (main) and side connector joint in a compression test for a specific design
members affect the load carrying capacity of the joint. problem yielded the data as given below:

Strength of Improvised Split Ring Connectors in Mesua (A4esuaferra) (Pilot Study)

No. and No. and Size Side Central Load End Inter- Load per
Diameter of Bolt used in Member Member Direction Distance mediate Pair
of Ring a Joint w. r.t. Distance of
used in a Grains of Connector
Joint Wood
~~~ ~
No. Size No. Size Thick- Width Thick- Width mm mm kgf
ness new
mm mm mm mm mm mm
(1) (2) (3) (4] (5) (6) (7) (8) (9) (10) (11) (12)

2 63 1 12X 125 31 92 38 92 Parallel 63 — 3930


2 63 1 12x 125 31 92 38 92 Parallel 75 — 4185
2 63 1 12 X 150 38 92 63 92 Parallel 75 — 4010
2 63 1 12 X 150 38 117 63 117 Parallel 75 4450
2 63 I 12x 125 31 138 38 92 Perpendicular 69 2520
2 63 1 12X 125 38 138 38 92 Perpendicular 69 3515
2 100 1 19 X 175 38 138 66 138 Parallel 100 7075
2 100 1 19X 175 38 138 66 138 Parallel 125 7370
2 100 1 19x 175 41 138 75 138 Parallel 100 — 7220
2 100 1 19x 175 41 138 75 138 Parallel 125 — 7645
4 100 2 19 X200 38 138 66 138 Parallel 100 150 5655
4 100 2 19 X200 41 138 75 138 Parallel 100 150 5925
4 100 2 19 x200 41 138 75 138 Parallel 125 200 7135

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 37


----- ----- _____ _

<. )

SPLIT RING CONNECTOR

e ---- - ----
fl -h I

rr n
---- ---- I
II J

e t,
d-l t r

a/2
I
tl-a a12

FIG. 8 STRESSDISTRIBUTIONIN A SPLIT RING CONNECTOR

10.2 Wooden Disc-Dowel The edge clearance shall range from 12 mm to 20 mm


as per the size of the dowel. The end clearance shall be
10.2.1 It is a circular hardwood disc general] y tapered
at least equal to the diameter of dowel for joints
each way from the middle so as to form a double
subjected to tension and three-fourth the diameter for
conical frustum. Such a disc is made to fit into
compression joints. Disc-dowel shall be turned from
preformed holes (recesses), half in one member and
quarter sawn planks of seasoned material.
the other half in another, the assembly being held by
one mild steel bolt through the centre of the disc to act 10.2.3 Choice of Species
as a coupling for keeping the jointed wooden members
Wood used for making dowels shall be fairly straight
from spreading apart.
grained, free from excessive liability to shrink and
10.2.2 Dimensions ofillembers warp, and retain shape well after seasoning species
recommended include:
The thickness of dowel may vary from 25 mm to
35 mm anti diameter from 50 mm to 150 mm. The Babul
di[~lneter of dowel’ shall be 3.25 to 3.50 times the Dhaman
thickness. Irul

?,g NATIONAL BUILDING CODE OF INDIA


Sisscm 10.2.4 Design Considerations
Rose wood Figure 9 illustrates the forces on dowel in a lap joint
Sandal and butt joint. Dowel is subjected to shearing at the
Axle-wood mid-section, and compression along the grain at the
Padauk bearing surfaces. For equal strength in both the forces,
formula equations are given in Fig. 9 to determine the
Pyinkado
size of dowel.
Yon
The making of wooden discs may present some
NOTE — Data on the above species as per Table 1 except
for the species Pyinkado, which is not an indigenous species. problems in the field, but they may be made in small

DOWEL

LAP JOINT *

BUTT JOINT

Lap Joint: Bolt in simple tension due to clockwise turning moment on dowel:
Butt Joint: No tilting moment in dowel due to balancing effect [dowels are in shear (no bending, shearing
and tensile stress on bolts)]
Size of dowel for equal strength in both shearing and bearing.

rcd’/4x S=dxt/2xc
where

d= Mid diameter of the dowel, t


t = Thickness of dowel,
s = Safe working stress in shear along grain, and
c = Safe compressive stress along grain.

NOTE — Symbols are exclusive to this figure.

FIG. 9 DISTRIBUTIONOF FORCESIN DOWEL JOINT

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 39

.,
workshop to the specifications of the designer. This is g) Assembly and pressing the laminations;
also economically important. Once the wood fittings h) Curing the glue lines, as specified; and
are shop tailored and made, the construction process j) Finishing, protection and storage.
in the field is greatly simplified.
11.2 Finger joints are glued joints connecting timber
Theoretical safe loads in design shall be confirmed members end-to-end (Fig. 10). Such joints shall be
through sample tests. produced by cutting profiles (tapered projections) in
NOTE — Some experimental studies have indicated the the form of V-shaped grooves to the ends of timber
following safe loads in kgf for dowels bearing parallel to the planks or scantling to be joined, glueing the interfaces
grain.
and then meeting the two ends together under pressure.
Finger joints provide long lengths of timber, ideal for
upgrading timber by permitting removal of defects,
minimizing warping and reducing wastage by avoiding
short off-cuts.
(1) (2) (3) (4) (5) (6) (7) (8)
SLII BabUl 680 1000 1360 1815 2270 2810 11.2.1 In finger joints the glued surfaces are on the
side grain rather than on the end grain and the glue
Sal Sissoo 545 770 1045 1360 1725 2130
line is stressed in shear rather in tension.

11 GLUED LAMINATED CONSTRUCTION 11.2.1.1 The figures can be cut from edge-to-edge or
AND FINGER JOINTS from face-to-face. The difference is mainly in
appearance, although bending strength increases if
11.1 Developments in the field of synthetic adhesive
several fingers share the load. Thus a joist is slightly
have brought glueing techniques within the range of
stronger with edge-to-edge finger joints and a plank is
engineering practice. Timber members of larger cross-
stronger with face-to-face finger joint.
sections and long lengths can be fabricated from small
sized planks by the process of gluelam. The term glued 11.2.1.2 For structural finger jointed members for
laminated timber construction as applied to structural interior dry locations, adhesives based on melamine
members refers to various laminations glued together, formaldehyde cross linked polyvinyl acetate (PVA) are
either in straight or curved form, having grain of all suited. For high humid and exterior conditions, phenol
laminations essentially parallel to the lengths of the formaldehyde and resorcinol formaldehyde type
member. adhesives are recommended. Proper adhesives should
be selected in consultation with the designer and
11.1.1 Choice of Glue
adhesive manufacturers and assessed in accordance
The adhesive used for glued laminated assembly are with accepted standard [6-3A( 11)].
‘gap filling’ type. A ‘filler’ in powder form is
11.2.2 Manufacturing Process
introduced in the adhesive. Structural adhesives are
supplied either in powder form to which water is added In the absence of sophisticated machinery, the finger
or in resin form to which a hardener or catalyst is added, joints shall be manufactured through intermediate
For choice of glues, reference may be made to good technology with the following steps: #
practice [6-3A(1 l)]. However, it is important that only 1“
a) Drying of wood,
boiling water proof (BWP) grade adhesives shall be
used for fabrication of gluelam in tropical, high humid b) Removal of knots and other defects,
climates like India. c) Squaring the ends of the laminating planks,
d) Cutting the profile of finger joint in the end
11.1.2 Manufacturing Schedule
grain,
In absence of a systematic flow-line in a factory, e) Applying adhesives on the finger interfaces,
provisions of intermediate technology shall be created f) Pressing the joint together at specified pressure,
for manufacturing structural elements. The schedule
g) Curing of adhesive line at specified
involves steps: temperature, and
a) Drying of planks; h) Planning of finger-jointed planks for smooth
b) Planning; surface.
c) End-jointing by scarfs or fingers; 11.2.3. Strength
d) Machining of laminations; Strength of finger joints depends upon the geometry
e) Setting up dry assembly of structural unit; of the profile for structural purpose; this is generally
f) Application of glue; 50 mm long, 12 mm pitch.

40 NATIONAL BUILDING CODE OF INDIA


[ I i
I [
1!

TIP GAP L
1

L = FINGER LENGTH
p = PITCH
t = TIP THICKNESS
0=6”

.
.6

ORIENTATION OF FINGER JOINTS

FIG. 10 TYPICALFINGERJOINTGEOMETRY

11.2.3.1 End joints shall be scattered in adjacent with fibre oriented along a specific direction have
laminations, which shall not be located in very highly been developed and are being adopted for load
stressed outer laminations. bearing applications. Laminated veneer lumber is one
11.2.4 Tip thickness will be as small as practically such product developed as a result of researches in
possible. plantation grown species of wood. Density of
iaminated v&eer lumber ranges from 0.6 to 0.75
12 LAMINATED VENEER LUMBER which is manufactured in accordance with good
12.1 Certain reconstituted lignocellulosic products practice [6-3A(1 2)].

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER

..
12.1.1 Dimensions accordance with established engineering principles and
good practice. A glued laminated beam is a straight
Sizes of laminated veneer lumber composite shall be
member made from a number of laminations assembled
inclusive of margin for dressing and finishing unless
both ways either horizontally or vertically. While
rnanufiactured to order. The margin for dressing and
vertical laminations have limitations in restricting
finishing shall not exceed 3mm in the width and
the cross-section of a beam by width of the plank,
thickness and 12mmin the length.
horizontally laminated section offers wider scope to
12.1.2 Permissible Defects the designer in creating even the curved members.
Simple straight beams and joists are used for many
Jointing gaps — Not more than 3 mm wide, structures from small domestic rafters or ridges to the
provided they are well staggered in light industrial structures.
their spacing and position between
the successive plies. 13.2 Design
Slope of grain — Not exceeding 1 in 10 in the face The design of glue laminated wood elements shall be
layers. in accordance with good engineering practice and shall
Tight knot — Three numbers up to 25 mm take into consideration the species and grade of timber
diameter in one square metre used, presence of defects, location of end joints in
provided they are spaced 300 mm laminations, depth of beams and moisture contents
or more apart. expected while in service. Beams of large spans shall
Warp — Not exceeding 1.5 mm per metre be designed with a suitable camber to assist in
length. achieving the most cost effective section where
deflection governs the design. The strength and
12.1.3 Strength Requirements stiffness of laminated beams is often governed by the
quality of outer laminations. Glued laminated beams
The strength requirements for laminated veneer lumber
can be tapered to follow specific roof slopes across a
shall be as per Table 17.
building and/or to commensurate with the varying
13 DESIGN OF GLUED LAMINATED BEAMS bending moments.

13.1 General 13.3 Material


.
Glued laminated structural members shall be fabricated Laminating boards shall not contain decay, knots or
*
only where there are adequate facilities for accurate other strength reducing characteristics in excess of
sizing and surfacing of planks, uniform application of those sizes or amounts permitted by specifications. The
glue, prompt assembly, and application of adequate moisture content shall approach that expected in
pressure and prescribed temperature for setting and service and shall in no case exceed 15 percent at the
curing of the glue. Design and fabrication shall be in time of glueing. The moisture content of individual

Table 17 Requirements of Laminated Veneer Lumber


(Clause 12.1.3)

S1No. Properties Requirement

(1) (2) (3)

i) Modulus of rupture (N/mm2), A4in 50


ii) Modulus of elasticity (N/mm2), Min 7500
iii) Compressive strength parallel to grain (N/mm2), Min 35
iv) Compressive strength perpendicular to grain:
a) Parallel to grain (N/mm2), A4in 35
b) Perpendicular to grain (N/mm2), Min 50
v) Horizontal shear:
a) Parallel to laminae (Nhrnn2), Min 6
b) Perpendicular to larninae (N/mm2), Min 8
vi) Tensile strength parallel to grain (N/rnm2), Min 55
vii) Screw holding powen
a) Edge (N), Min 2300
b) Face (N), Min 2700
viii) Thickness swelling in 2 h water soaking (percent), Max 3

42 NATIONAL BUILDING CODE OF INDIA

..
laminations in a structural member shall not differ by stiffness of wood result in structures characterized
more than 3 percent at the time of glueing. Glue shall by high stiffness for even medium spares. Plywood
be of type suitable for the intended service of a can act as web transmitting shear stress in web bearing
structural member. or stressed skin or sandwich construction. The
effective moment of inertia of web beam and stressed
13.4 FabricationfManu facture skin construction depends on modular ratio that is, E
In order to assure a well-bonded and well-finished of wood to E of plywood.
member of true shape and size, all equipments, end- 14.3 Structural plywood is also very efficient as
Jointing,glue spread, assembly, pressing, curing or any cladding material in wood frame construction, such as
other operation in connection with the manufacture of houses. This type of sheathing is capable of resisting
glued structural members shall be in accordance racking due to wind and quack forces. Structural
with the available good practices and as per glue plywood has been widely used as diaphragm
manufacturers’ instructions as applicable. (horizontal) as in roofing and flooring in timber frame
construction. It has been established that 6 mm thick
13.5 Testing
plywood can be used for sheathing and even for web
For examining the quality of glue and its relative and stressed skin construction, 9-12 mm thick plywood
strength wki-vis species of timber in glued laminated is suitable for beams, flooring diaphragms, etc. Phenol
construction, it is necessary to conduct block shear and formaldehyde (PF) and PRF adhesive are suitable for
other related tests in accordance with accepted standard fabrication of glued plywood components. 6 mm-
16-3A(1 l)]. 12 mm thick structural plywood can be very well used
as nailed or bolded gussets in fixing members of trusses -.
Structural loading tests on prototype sizes provide
or lattice griders or trussed rafters.
information on the strength properties, stiffness or
rigidity against deflection of a beam. Normally, scarf joints are used for fixing plywood to
required length and timber can be joined by using either
14 STRUCTURAL USE OF PLYWOOD finger or scarfjoints. Arch panels, folded plates, shelves
Unlike sawn timber, plywood is a layered panel product are other possibilities with this technique.
comprising veneers of wood bonded together with
15 TRUSSED RAFTER
adjacent layers usually at right angles. As wood is
strongest when stressed parallel to grain, and weak 15.1 General
perpendicular to grain, the lay up or arrangement of
A roof truss is essentially a plane structure which is
veneers in the panel determines its properties. When
very stiff in the plane of the members, that is, the plane
the face grain of the plywood is parallel to the direction
in which it is expected to carry loads, but very flexible
of stress, veneers parallel to the face grain carry almost
in every other direction. Thus it can virtually be seen
all the load. Some information/guidelines for structural
as a deep, narrow girder liable to buckling and twisting
use of plywood which would be manufactured in
under loads. In order, therefore, to reduce this effect,
accordance with accepted standard [6-3A( 13)] are
eccentricity of loading and promote prefabrication for
given in 14.1 to 14.3.
economy, low-pitched trussed rafters are designed with
14.1 The plywood has a high strength to weight ratio, bolt ply/nail ply joints. Plywood as gussets, besides
and is dimensionally stable material available in sheets being simple have inherent constructional advantage
of a number of thicknesses and construction. Plywood of grain over solid wood for joints, and a better balance
can be sawn, drilled and nailed with ordinary wood is achievable between the joint strength and the
working tools. The glues used to bond these veneers member strength.
together are derived from synthetic resins which are
Trussed rafters are light weight truss units spaced at
set and cured by heating. The properties of adhesives
close centres for limited spans to carry different types
can determine the durability of plywood.
of roof loads. They are made from timber members of
14.2 In glued plywood construction, structural uniform thickness fastened together in one plane. The
plywood is glued to timber resulting in highly plywood gussets may be nailed or glued to the timber
efficient and light structural components like web to form the joints. Conceptually a trussed rafter is a
beams (I and box sections), (Fig. 11 and Fig. 12) triangular pin jointed system, traditionally meant to
stressed skin panels (Fig. 13) used for flooring and carry the combined roof weight, cladding services and
walling and pre-fabricated houses, cabins, etc. wind loads. There is considerable scope for saving
Glueing can be carried out by nail glueing techniques timber by minimizing the sections through proper
with special clamps. High shear strength of plywood design without affecting structural and functional
in combination with high flexural strength and requirements.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 43


WOODEN FLANGE
(TYPICAL)
7
PLYWOOD
PLYWOOD
WEBS YWOOD
WEB

,
I-SECTION DOUBLE-I BOX

FIG. 11 TYPICAL CROSS-SECTION OF WEB BEAMS

T’FFNER
\
//=E -+x
PLYWOOD
7

---lx
UPT06-9m 9
Hill
SECTION XX

~spAN upTo 9 m e

DOUBLE TAPERD

~spAN l.jpTo 9 m-~

HAUNCHED

FIG. 12 WEB BEAM CONFIGURATIONS

NATIONAL BUILDING CODE OF INDIA

..
,
FIG. 13 STRESSEDSKIN PANEL CONSTRUCTION(SINGLE SKIN ORDOUBLESKIN)

Trussed rafters require to be supported only at their accepted standard [6-3A( 13)]. Introduction of a
ends so that there is no need to provide load bearing plywood gusset simplifies the jointing and in addition
internal walls, Purlins, etc are dispensed with and in provides rigidity to the joint. Preservation of plywood
comparison with traditional methods of construction and other panel products shall be done in accordance
they use less timber and considerably reduces of site with good practice [6-3A( 14)].
labour, Mass production or reliable units can be carried
out under workshop controls. 16 STRUCTURAL SANDWICHES

15.2 Design 16.1 General

Trussed rafter shall be designed to sustain the dead Sandwich constructions are composites of different
and imposed loads specified in Part 6 ‘Structural materials including wood based materials formed by
Design: Section 1 Loads, Forces and Effects’ and the bonding two thin facings of high strength material to a
combinations expected to occur. Extra stresses/ light weight core which provides a combination of
deflections during handling, transportation and erection desirable properties that are not attainable with the
shall be taken care of. Structural analysis, use of load- individual constituent materials (Fig. 14). The thin
slip and moment, rotation characteristics of the facings are usually of strong dense material since that
individual joints may be used if feasible. Alternatively are the principal load carrying members of the
the maximum direct force in a member maybe assessed construction. The core must be stiff enough to ensure
to be given by an idealized pin-jointed framework, fully the faces remain at the correct distance apart. The
loaded with maximum dead and imposed load in the sandwiches used as structural elements in building
combination in which they may reasonably be expected construction shall be adequately designed for their
to occur. intended services and shall be fabricated only where
there are adequate facilities for glueing or otherwise
15.3 Timber bonding cores to facings to ensure a strong and durable
The species of timber including plantation grown product. The entire assembly provides a structural
species which can be used for trussed rafter element of high strength and stiffness in proportion to
construction and permissible stresses thereof shall be its mass.
in accordance with Table 1. Moisture contents to be as Non-structural advantages can also be derived by proper
per zonal requirements in accordance with 4.4. selection of facing and core material for example, an
impermeable facings can be used to serve as a moisture
15.4 Plywood
barrier for walls and roof panels and core may also be
Boiling water resistant (BWR) grade preservative selected to provide thermal and/or acoustic insulation,
treated plywood shall be used in accordance with fwe resistance, etc, besides the dimensional stability.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 45


u FACE SHEETS

FIG. 14 STANDWICHCONSTRUCTIONIN STRUCTURALAPPLICATIONS

16.2 Cores a) Flexural strengtldstiffness,


b) Edge-wise compressions,
Sandwich cores shall be of such characteristics as to
give to the required lateral support to the stressed c) Flat-wise compression,
facings to sustain or transmit the assumed loads or d) Shear in flat-wise plane,
stresses. Core generally carries shearing loads and to e) Flat-wise tensions,
support the thin facings due to compressive loads. Core Flexural creep (creep behaviour of adhesive),
0
shall maintain the strength and durability under
g) Cantilever vibrations (dynamic property), and
the conditions of service for which their use is
h) Weathering for dimensional stability.
recommended. A material with low E and small shear
modulus may be suitable. 17 LAMELLA ROOFING
16,3 Facings 17.1 General
Facings shall have sufficient strength and rigidity to The Lamella roofing offers an excellent architectural
resist stresses that may come upon them when edifice in timber, amenable to prefabrication, light
fabricated into a sandwich construction. They shall be weight structure with high central clearance. It is
thick enough to carry compressive and tensile stresses essentially an arched structure formed by a system of
and to resist puncture or denting that maybe expected intersecting skewed arches built-up of relatively short
in normal usages. timber planks of uniform length and cross-section.

16.4 Designing Roof is designed as a two hinged arch with a depth


equal to the depth of an individual lamella and width
Structural designing may be comparable to the design equal to the span of the building. The curved lamellas
of I-beams, the facings of the sandwich represent the (planks) are bevelled and bored at the ends and bolted
flanges of the I-beam and the sandwich core I-beam together at an angle, forming a network (grid) pattern
web. of mutually braced and stiffened members (Fig. 15).

16.5 Tests The design shall be based on the balanced or


Panels of sandwich construction shall be subject to unbalanced assumed load distribution used for roof
testing in accordance with accepted standards arches. Effect of deformation or slip of joints under
[6-3A(15)]. Tests shall include, as applicable, one or load on the induced stresses shall be considered in
more of the following: design. Thrust components in both transverse and

46 NATIONAL BUILDING CODE OF INDIA


F=

LAMELLA GRID

/WIND BLOCK

LAMELLA GRID

MIDDLE LAMELLA1
11111

L
I
H H
38”

w,=
BOLT
LAMELLA
“~ ‘\,
\
‘p. ‘r

LAMELLA NODAL JOINT v

LOADREACTIONDIAGRAM ‘

FIG. 15 TYPICAL ARRANGEMENTOFLAMELLA ROOFING

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 47

.
longitudinal directions due to skewness
of the building come into play predominantly. In structural nailed
of the lamella arch shall be adequately resisted. Thrust joints, nails are essentially loaded laterally, the design
at lamella joints shall be resisted by the moment of data for which is already available as standard code of
inertia in the continuous lamella and roof sheathening practice. Data on holding power of nailslscrews in
(decking) of lamella roofing. The interaction of arches different species is also useful for common commercial
in two directions adds to the strength and stability purposes. The resistance of mechanical fastenings is a
against horizontal forces. For design calculations function of the specific gravity of wood, direction of
several assumption tested and observed derivations, penetration with respect to the grain direction, depth
long-duration loading factors, seasoning advantages of penetration and the diameter of fastener assuming
and effects of defects are taken into account. that the spacing of fasteners should be adequate to
preclude splitting of wood.
17.2 Lamellas
18.2 Nails
Planking shall be of a grade of timber that is adequate
in strength and stiffness to sustain the assumed loads, Nails are probably the most common and familiar
forces, thrust and bending moments generated in fastener. They are of many types and sizes in
Lamella roofing. Lamella planks shall be seasoned to accordance with the accepted standards [6-3 A(16)].
a moisture content approximating that they will attain In general nails give stronger joints when driven into
in service. Lamella joints shall be proportioned so that the side grain of wood than into the end grain. Nails
allowable stresses at bearings of the non-continuous perform best when loaded laterally as compared to axial
lamellas on the continuous Iamellas or bearings under withdrawal so the nailed joints should be designed for
the head or washer of bolts are not exceeded. lateral nail bearing in structural design. Information
on withdrawal resistance of nails is available and joints
17.3 Construction may be designed for that kind of loading as and when
Design and construction of lamella roofs in India necessary.
assumes the roof surfaces to be cylindrical with every
18.3 Screw
individual lamella an elliptic segment of an elliptical
arch of constant curved length but of different Next to the hammer driven nails, the wood screw may
curvature. Lamella construction is thus more of an art be the most commonly used fastener. Wood screws
than science as there is no analytical method available are seldom used in structural work because of their
for true generation of schedule of cutting lengths and primary advantage is in withdrawal resistance, for
curvature of curved members forming the lamella grid. example, for fixing of ceiling “boards to joists, purlin
Dependence of an engineer on the practical ingenuity cleats, besides the door hinges etc. They are of
of master carpenter is almost final. All the lamella joints considerable structural importance in fixture design and
shall be accurately cut and fitted to give full bearing manufacture. Wood screws are generally finished in a
without excessive deformation or slip. Bolts at lamella variety of head shapes and manufactured in various
splices shall be adequate to hold the members in their lengths for different screw diameters or gauges in
proper position and shall not be over tightened to cause accordance with the accepted standard [6-3 A(17)].
bending of the lamellas or mashing of wood under the
The withdrawal resistance of wood screws is a function
bolt heads. Connection of lamellas to the end arches
of screw diameter, length of engagement of the
shall be adequate to transmit the thrust or any other
threaded portion into the member, and the specific
force. Sufficient false work or sliding jig shall be
gravity of the species of wood. Withdrawal load
provided for the support of lamella roof during actual
capacity of wood screws are available for some species
construction/erection.
and joints may be designed accordingly. End grain load
18 NAIL AND SCREW HOLDING POWER OF on wood screws are unreliable and wood screws shall
TIMBER not be used for that purpose.

18.1 General 19 PROTECTION AGAINST TERMITE ATTACK


IN BUILDINGS
One of the most common ways of joining timber pieces
to one another is by means of common wire nails and 19.1 Two groups of organisms which affect the
wood screws. Timber is used for structural and non- mechanical and aesthetic properties of wood in houses
structural purposes inform of scantlings, rafters, joists, are fungi and insects. The most important wood
boarding, crating and packing cases, etc needing destroying insects belong to termites and beetles. Of
suitable methods of joining them. Nevertheless it is about 250 species of wood destroying termites recorded
the timber which holds the nails or screws and as such in India, not more than a dozen species attack building
pulling of the nails/screws is the chief factor which causing about 90 percent of the damage to timber and

48 NATIONAL BUILDING CODE OF INDIA


other cellulosic materials. Subterranean termites are heartwood while sapwood is normally always
the most destructive of the insects that infest wood susceptible to attack by organisms. Preservatives
in houses justifying prevention measures to be should be well applied with sufficient penetration into
incorporated in the design and construction of timber. For engineers, architects and builders, the
buildings. following are prime considerations for choice of
preservatives:
19.1.1 Control measures consist inisolating orsealing
off the building from termites by chemical and non- a) Inflammability of treated timber is not
chemical construction techniques. It is recognized that increased and mechanical properties are not
95 percent damage is due to internal travel of the decreased;
termites from ground upwards rather than external b) Compatibility with the glue in laminated
entry through entrance thus calling upon for wood, plywood and board material;
appropriate control measures in accordance with good c) Water repellent effect is preferred;
practices [6-3A(1 8)].
d) Possible suitability for priming coat;
19.2 Chemical Methods e) Possibility of painting and other finishes;
f) Non-corrosive nature in case of metal
Termites live in soil in large colonies and damage the
fasteners; and
wooden structure in the buildings by eating up the wood
or building nests in the wood. Poisoning the soil under !3) Influence on plastics, rubber, tiles and
and around the building is a normal recommended concrete.
practice. Spraying of chemical solution in the trenches 19.4 Constructional Method
of foundations in and around walls, areas under floors
before and after filling of earth, etc. In already Protection against potential problem of termite attack
constructed building the treatment can be given by can simply be carried out by ordinary good construction
digging trenches all around the building and then giving which prevents a colony from gaining access by:
a liberal dose of chemicals and then closing the trenches. a) periodic visual observations on termite
galleries to be broken offi
19.3 Wood Preservatives
b) specially formed and properly installed metal
Natural resistance against organisms of quite a few shield at plinth level; and
wood species provides durability of timber without c) continuous floor slabs, apron floors and
special protection measure. It is a property of termite grooves on periphery of buildings.

LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’ timber testing and their
in the fulfillment of the requirements of the Code. The conversion (second revision)
latest version of a standard shall be adopted at the time (3) 4970:1973 Key for identification of
of the enforcement of the Code. The standards commercial timbers (first
listed may be used by the Authority as a guide in revision)
conform~nce with the requirements-of the ‘referred
(4) 287:1993 Recommendations for
clauses in the Code. maximum permissible
IS No. Title moisture content of timber
used for different purposes
(1) 707:1976 Glossary of terms applicable
(third revision)
to timber technology and
utilization (second revision) (5) 3629:1986 Specification for structural
timber in building (first
(2) 1708 Methods of testing small
revision)
(l%u-Ls1 to 18) :1986 clear specimens of timber
(6) 401:2001 Code of practice for
(second revision)
preservation of timber
2408: 1963 Methods of static tests of ~ourth revision)
timbers in structural sizes
(7) 2366:1983 Code of practice for nail-
2455:1990 Methods of sampling of jointed timber construction
model trees and logs for ($rst revision)

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3A TIMBER 49


1S No. Title IS No. Title
(8) 4983:1968 Code of practice for design (Parts 1 to 7) :1979 based structural sandwich
and construction of nail construction
laminated timber beam (first (16) 723:1972 Specification for steel
revision) countersunk head wire nails
(9) I [096 :1984 Code of practice for design (first revision)
construction of bolt-jointed (17) 451:1999 Technical supply conditions
construction for wood screws (fourth
(10) 4907:1968 Methods of testing timber revision)
connectors 6736:1972 Specification for slotted
(11)9188:1979 Performance requirements countersunk head wood
for adhesive for structural screw
laminated wood products 6739:1972 Specification for slotted
for use under exterior round head wood screw
exposure condition 6760:1972 Specification for slotted
(12) 14616:1999 Specification for laminated countersunk head wood
veneer lumber screws

(13) 107OI :1983 (18) 6313 Code of practice for anti-


Specification for structural
termite measures in
plywood
buildings:
4990:1993 Specification for plywood
(Part 1): 1981 Constructional measures
for concrete shattering work
@st revision)
(second revision)
(Part 2): 2001 Pre-constructional chemical
(14) 12120:1987 Code of practice for
treatment measures (second
preservation of plywood
revision)
and other pane products
(Part 3): 2001 Treatment for existing
(15) 9307 Methods of test for wood buildings (second revision)

50 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 3 Timber and Bamboo: 3B Bamboo

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD . . 3

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 SYMBOLS ... 7
4 MATERIALS . .. 7
5 PERMISSIBLE STRESSES ... 11
6 DESIGN CONSIDERATIONS ... 11
7 DESIGN AND TECHNIQUES OF JOINTS ... 13
8 STORAGE OF BAMBOO ... 20

ANNEX A SOURCE AND LOCAI/ NAMES OF SOME OF THE SPECIES ... 21


OF BAMBOO

LIST OF STANDARDS ... 23

---
.

2 NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

Bamboo is versatile resource characterized by high strength to weight ratio and ease in working with simple
tools. It has a long and well established tradition as a building material throughout the tropical and sub-tropical
regions. It is used in many forms of construction, particularly, for housing in rural areas. But, enough attention
had not been paid towards research and development in bamboo as had been in the case with other materials of
construction including timber. However, of late bamboo is being given its due importance and realization by
national and international organizations. A need is being felt for design and construction code in bamboo for a
number of social and trade advantages, engineering recognition and improved respectability. Forest Research
Institute, Debra Dun and some other organizations have been engaged in bamboo research to establish its
silviculture, botanical nomenclature, entomological and pathological aspects and utilization base.

Some of the suitable species grown in India and neighboring countries are enlisted in Annex A along with their
local names and source, for general information.

Analogous to some constructional timbers, bamboo possesses better strength-to-mass and cost ratio. Resilience
coupled with lightness makes bamboo suitable for housing in disaster-prone areas such as areas prone to earthquake.
It has the capacity to absorb more energy and show larger deflections before collapse and as such is safer under
earth tremors. At present, the application of bamboo as an engineering material is largely based on practical and
engineering experience as the design guidelines are inadequate,

The bamboo culm has a tubular structure consisting essentially of nodes and inter-nodes. In the inter-nodes the
cells are axially oriented while the nodes provide the transverse inter-connection. The disposition of the nodes
and the wall thickness are significant in imparting strength to bamboo against bending and crushing. In a circular
cross-section, bamboo is generally hollow and for structural purposes this form is quite effective and advantageous.
Each of the species of barnboo has widely different characteristics affecting its usefulness as constructional
material. The strength of bamboo culms, their straightness, lightness combined with hardness, rtige and size of
hollowness make them potentially suitable for a variety of applications both structural and non-structural. With
good physical and mechanical properties, low shrinkage and good average density, bamboo is well suited to
replace wood in several applications, especially in slats and panel form.

In the earlier version of this Code, timber was covered under Section 3 of Part 6 under the title Wood, which did
not cover Bamboo. In this revision, this Section has been enlarged and titled as Section 3 Timber and Bamboo.
This has been sub-divided into sub-section 3A Timber and sub-section 3B Bamboo. Bamboo has found a place
in this draft revision of the Code for the first time. This subsection pertains to bamboo and may be read in
conjunction with sub-section 3A Timber.

The information contained in this Section is largely based on the works carried out at Forest Research Institute,
Debra Dun, Indian Plywood Industries Research and Training Institute, Bangalore, INBAR documents and the
following Indian Standards:

IS No. Title
6874:1973 Method of test for round bamboo
8242:1976 Method of test for split bamboo
9096:1979 Code of practice for preservation of bamboo for structural purposes
13958:1994 Specification for bamboo mat board for general purposes
.
All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO 3


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 3 Timber and Bamboo: 3B Bamboo

1 SCOPE as found in stem pith or fruit pulp, (b) Epidermis —


the outermost layer of cells covering the surface of a
This Section relates to the use of bamboo for
plant, when there are several layers of tissue.
constructional purposes in structures or elements of
the structure, ensuring quality and effectiveness of 2.2 Structural Purpose Definitions
design and construction using bamboo. It covers
2.2.1 Bamboo Mat Board — A board made of two or
minimum strength data, dimensional and grading
more bamboo mats bonded with an adhesive.
requirements, seasoning, preservative treatment, design
and jointing techniques with bamboo which would 2.2.2 Beam — A structural member which supports
facilitate scientific application and long-term load primarily by its internal resistance to bending.
performance of structures. It also covers guidelines so
2.2.3 Breaking Strength — A term loosely applied
as to ensure proper procurement, storage, precautions
to a given structural member with respect to the
and design limitations on bamboo.
ultimate load it can sustain under a given set of
2 TERMINOLOGY conditions.

2.0 For the purpose of this Section, the following 2.2.4 Bundle-Column — A column consisting of three
definitions shall apply. or more number of cuhu bound as integrated unit with
wire or strap type of fastenings.
2.1 Anatomical Purpose Definitions
2.2.5 Centre Internode — A test specimen having its
2.).1 Bamboo — Tall perennial grasses found in centre between two nodes.
tropical and sub-tropical regions. They belong to the
2.2.6 Characteristic Load— The value of loads which
family Poaceae and sub-family Bambusoidae.
has a 95 percent probability of not exceeding during
2.1.2 Bamboo Culm — A single shoot of bamboo the life of the structure.
usually hollow except at nodes which are often swollen.
2.2.7 Characteristic Strength — The strength of the
2.1.3 Bamboo Clump — A cluster of bamboo culms material below which not more than 5 percent of the
emanating from two or more rhizomer in the same test results are expected to fall.
place.
2.2.8 Cleavability — The ease with which bamboo
2.1.4 Cellulose — A carbohydrate, forming the can be split along the longitudinal axis. The action of
fundamental material of all plants and a main source splitting is known as cleavage.
of the mechanical properties of biological materials.
2.2.9 Column — A structural member which supports
2.1.5 Cell — A fundamental structural unit of plant axial load primarily by inducing compressive stress
and animal life, consisting of cytoplasm and usually along the fibres.
enclosing a central nucleus and being surrounded by a
2.2.10 Common Rafter — A roof member which
membrane (animal) or a rigid cell wall (plant).
supports roof battens and roof coverings, such as
2.1.6 Cross Wall — A wall at the node closing the boarding and sheeting.
whole inside circumference and completely separating
2.2.11 Curvature — The deviation from the
the hollow cavity below from that above.
straightness of the culm.
2.1.7 Hemi Cellulose — The polysaccharides
2.2.12 Delamination — Separation of mats through
consisting of only 150 to 200 sugar molecules, also
failure of glue.
much less than the 10000 of cellulose.
2.2.13 End Distance — The distance measured
2.1.8 Lignin — A polymer of phenyl propane units,
parallel to the fibres of the bamboo from the centre of
in its simple form (CGH~CHqCHzCH~).
the fastener to the closest end of the member.
2.1.9 Sliver — Thin strips of bamboo processed from
2.2.14 Flatten Bamboo — Bamboo consisting of culms
bamboo culm.
that have been cut and unfolded till it is flat. The culm
2.1.10 Tissue — Group of cells, which in higher plants thus is finally spread open, the diaphragms (cross walls)
consist of(a) Parenchyma — a soft cell of higher plants at nodes removed and pressed flat.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO 3B BAMBOO 5


r-

2.2.15 Full Culm — The naturally available circular 2.2.33 Roof Battens — A roof member directly
sectionlshape. supporting tiles, corrugated sheets, slates or other
roofing materials.
2.2.16 Fundamental or Ultimate Stress — The stress
which is determined on a specified typelsize of culms 2.2.34 Roof Skeleton — The skelton consisting of
..
of bamboo, in accordance with stmdard practice and bamboo truss or rafter over which solid bamboo purlins
does not take into account the effects of naturally are laid and lashed to the rafter or top chord of a truss
occurring characteristics and other factors. by means of galvanized iron wire, cane, grass, bamboo
leaves, etc.
2.2.17 Inner Diameter — Diameter of internal cavity
of a hollow piece of bamboo. 2.2.35 Slenderness Ratio — The ratio of the length of
member to the radius of gyration is known as
2.2.18 Inside Location — Position in buildings in
slenderness ratio of member. (The length of the
which bamboo remains continuously dry or protected
member is the equivalent length due to end conditions).
from weather,
2.2.36 Splits — The pieces made from quarters by
2.2.19 Joint — A connection between two or more
dividing the quarters radially and cutting
bamboo structural elements.
longitudinally.
2.2.20 Joist — A beam directly supporting floor,
2.2.37 Taper — The ratio of difference between
ceiling or roof of a structure.
minimum and maximum outer diameter to length.
2.2.21 Length of Internode — Distance between
2.2.38 Unloaded End Distance — The end distance
adjacent nodes. . ..
opposite to the loaded end.
2.2.22 Loaded End or Compression End Distance —
2.2.39 Wall Thickness — Half the difference between
The distance measured from the centre of the fastner
outer diameter and inner diameter of the piece at any
to the end towards which the load induced by the
cross-section.
fastener acts.
2.2.40 Wet Location — Position in buildings in which
2.2.23 Matchet — A light cutting and slashing tool in
the bamboos are almost continuously damp, wet or in
the form of a large knife.
contact with earth or water, such as piles and bamboo
2.2.24 Mat — A woven sheet made using thin slivers, foundations.

2.2.25 Mortise and Tenon — A joint in which the 2.3 Definitions Relating to Defects
reduced end (tenon) of one member fits into the
corresponding slot (mortise) of the other. 2.3.1 Bamboo Bore/GHOON Hole — The defect
caused by bamboo GHOON beetle (Dinoderus spp.
2.2.26 Net Section — Section obtained by deducting from Bost~chdae), which attacks felled culms,
the gross cross-section (A), the projected areas of all
materials removed by boring, grooving or other means. 2.3.2 Crookedness — A localized deviation from the
straightness in a piece of bamboo.
2.2.27 Node — The place in a bamboo culm where
branches sprout and a diaphragm is inside the culm 2.3.3 Discoloration — A change from the normal
and the walls on both sides of node are thicker. colour of the bamboo which does not impair the
strength of bamboo or bamboo composite products.
2.2.28 Outer Diameter — Diameter of a cross-section
of a piece of bamboo measured from two opposite 2.4 Definitions Relating to Drying Degrades
points on the outer surface.
2.4.1 Collapse — The defect occurring on account of
2.2.29 Outside Location — Position in building in excessive shrinkage, particularly in thick walled
which bamboos are occasionally subjected to wetting immature bamboo. When the bamboo wall shrinks, the
and drying as in case of open sheds and outdoor outer layers containing a larger concentration of strong
exposed structures, fibro-vascular bundles set the weaker interior portion
embedded in parenchyma in tension, causing the latter
2.2.30 Permissible Stress — Stress obtained after
to develop cracks. The interior crack develops into a
applying factor of safety to the ultimate or basic stress.
wide split resulting in a depression on the outer surface.
2.2,31 Principal Rafter — A roof member which This defect also reduces the structural strength of round
supports purlins. bamboo.

2.2.32 Purlins — A roof member directly supporting 2.4.2 End Splitting — A split at the end of a bamboo.
roof covering or common rafter and roof battens. This is not so common a defect as drying occurs both

6 NATIONAL BUILDING CODE OF INDIA


from outer and interior wall surfaces of bamboo as 4.1.1 Grouping
well as the end at the open ends.
Sixteen species of bamboo found suitable for structural
2.4.3 Surface Cracking — Fine surface cracks not applications and classified into three groups, namely,
detrimental to strength, However, the cracking which Group A, Group B and Group C are given in Table 2.
occurs at the nodes reduces the structural strength.
The characteristics of these groups areas given below:
2.4.4 Wrinkled and Deformed Surface — Deformation
in cross-section, during drying, which occurs in Limiting Strength Values (in Green Condition)
immature round bamboos of most species; in thick
Modulus of Modulus of Elasticity (E)
walled pieces, besides this deformation the outer
Rupture (R’) in Bending
surface becomes uneven and wrinkled. Very often the
N/mmz 103 N/mm*
interior wall develops a crack below these wrinkles,
running parallel to the axis. (1) (2) (3)

3 SYMBOLS Group A R’>70 E>9


Group B 70> R’>50 9>E>6
3.1 For the purpose of this Section, the following letter
Group C 50> R’>30 6>E>3
symbols shall have the meaning indicated against each,
unless otherwise stated:
4.1.2 Bamboo species may be identified using suitable
A= Cross-sectional area of bamboo methods.
(perpendicular to the direction of the
NOTE — Methods of identification of bamboo through
principal fibres and vessels), mmz anatomical characters have not been perfected so far.
Identification through morphological characters could be done
A=&2-d2) only on full standing culm by experienced sorters.

4.1.3 Dendrocalamus strictus and Bambusa


D= Outer diameter, mm
arundinacea are the two principal economic species
d= Inner diameter, mm
of which the former occupies the largest area and is
E= Modulus of elasticity in bending, N/mm’ the most common owing to the vast expanse and
j; = Calculated stress in axial compression, suitability as a raw material for industrial uses.
N/mmz
4.2 Species of bamboo other than those listed in the
f;,, = Permissible stress in compression along the
Table 2 may be used, provided the basic strength
fibres, N/mm2
characteristics are determined and found more than the
limits mentioned therein. However, in the absence of
I= Moment of inertia, mm4 testing facilities and compulsion for use of other
species, and for expedient designing, allowable stresses
=; (D4 -d’) may be arrived at by multiplying density with factors
as given below:
1= Unsupported length of column
M= Moisture content, percent Allowable Long-Term Stress (N/mm2) per
r = Radius of gyration Unit Density (kg/m3)

— ~) Condition Axial Bending Shear


Compression
R’ = Modulus of rupture, N/mm’
(no buckli~g)
w= Wall thickness, mm
Green 0.011 0.015 —
z= Section modulus, mm3
~= Deflection or deformation, mm. Air dry (12%) 0.013 0.020 0.003

NOTE — In the laborato~ regime, the density of bamboo is


4 MATERIALS conveniently determined. Having known the density of any
species of bamboo, permissible stresses can be worked out
4.1 Species of Bamboo using factors indicated above. For example, if green bamboo
has a density of 600 kg/m3, the atlowable stress in bending
More than 100 species of bamboo are native to India
would be 0.015 x 600 = 9 N/mm’.
and a few of them are solid but most of them are hollow
in structure. Physical and mechanical properties of
4.3 Moisture Content in Bamboo
20 species of bamboo so far tested in green and dry
conditions in round form are given in Table 1. With decrease of moisture content (M) the strength of

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO 7


w
Table 1 Physical and Mechanical Properties of Indian Bamboos (in Round Form)
(Clauses 4.1 and 5.1.2)

S1 Species Properties
No. -
-
In Green Condition In Air Dry Conditions
A A
/ - #- -
Density Modulus of Modulus of Maximum Density Modulus of Modulus
Rupture Elasticity Compressive Strength Rupture of Elasticity
kg/m3 N/mm* 1(? N/mm* N/mm* kg/m3 N/mm* 103N/mm2

(1) (2) (3) (4) (5) (6) (7) (8) (9)

i) Bambusa auriculata 594 65.1 15.01 36.7 670 89.1 21.41


ii) B. balcooa 783 65.4 7.31 46.7 —
iii) B. bambos (Syn.B.atwndinacea) 559 58.3 5.95 35.3 663 80.1 8.96
iv) B. burmanica 570 59.7 11.01 39.9 672 105.0 17.81
v) B. glancescens (Syn.B.nana) 691 82.8 14.77 53.9 — — —
vi) B. nutans 603 52.9 6.62 45.6 673 52.4 10.72
vii) B. pallida 731 55.2 12.90 54.0 —
viii) B. polymo@uz 619 28.3 3.12 32.1 659 35.5 4.40
ix) B. tulda 658 51.1 7.98 40.7 722 66.7 10.07
x) B. ventricosa 626 34.1 3.38 36.1 —
xi) B. vulgaris 626 41.5 2.87 38.6 — —
xii) Cephalostachyum pergracile 601 52.6 11.16 36.7 640 71.3 19.22
xiii) Dendrocalamus giganteous 597 17.2 0.61 35.2 . —
xiv) D. hamiltonii 515 40.0 2.49 43.4 — —
xv) D. longispathus 711 33.1 5.51 42.1 684 47.8 6.06
xvi) D. membranacaus 551 26.3 2.44 40.5 664 37.8 3.77
xvii) D. strictus 631 73.4 11.98 35.9 728 119.1 15.00
xviii) Melocanna baccifera 817 53.2 11.39 53.8 751 57.6 12.93
xix) Oxytenanthera abyssinicia 688 83.6 14.% 46.6 — —
xx) Thyrsostachys oliveri 733 61.9 9.72 46.9 758 90.0 12.15

NOTES
1 As the strength of split bamboo is more than that of round bamboo, the results of tests on romd barnbo CaIIbe safely used for designing
withspit bamboo.
2 The values of stress in N/mm* have been obtained by converting the values in kgf/cm2 by dividing the same by 10.

,. .. .1-

.
!

Table 2 Safe Working Stresses of Bamboos for Structural Designing)


(Clauses 4.1.1,4 .2,5.3 and 5.4)

S1 Species Extreme Fibre Stress Modulus of Allowable


No. in Bending Elasticity Compressive Stress
N/mm2 103N/mm* N/mm2
(1) (2) (3) (4) (5)

GROUP A
i) Barnbusa glancescens (syn. B. nana) 20.7 3.28 15.4
ii) Dendrocalamus strictus 18.4 2.66 10.3
iii) Oxytenanthera abyss inicia 20.9 3.31 13.3
GROUP B
iv) Bambusa balcooa 16.4 1.62 13.3
v) B. pallida 13.8 2.87 15.4
vi) B. nutans 13.2 1.47 13.0
vii) B. tulda 12.8 1.77 11.6
viii) B. auriculata 16.3 3.34 10.5
ix) B. burmanica 14.9 2.45 11.4
x) Cephalostachyum pergraci[e 13.2 2.48 10.5
xi) Melocanna baccifera (Syn. M. bambusoides) 13.3 2.53 15.4
xii) Thyrsotachys oliveri 15.5 2.16 13.4
GROUP C
xiii) Bambusa arundinacea (Syn. B. bambos) 14.6 1.32 10.1
xiv) B. ventricosa 8.5 0.75 10.3
xv) B. vulgaris 10.4 0.64 11.0 t
xvi) Dendrocalamus longispathus 8.3 1.22 12.0

NOTE — The values of stress in N/mm* have been obtained by converting the values in kgf/cm2 by dividing the same by 10.

‘)The values given pertain to testing of barnboo in green condition.

bamboo increases exponentially and bamboo has an 4.3.2 Accelerated air seasoning method gives good
intersection point (fibre saturation point) at around 25 results. In this method, the nodal diaphragm (septa)
percent moisture content depending upon the species. are punctured to enable thorough passage of hot air
A typical moisture-strength relationship is given at from one end of the resulting bamboo tube to the other
Fig. 1. The moisture content of bamboo shall be end.
determined in accordance with good practice [6-3B(1)].
NOTE — For details, reference may be made to relevant
Matured culms shall be seasoned to about 20 percent publicationsof ForestResearchInstitute,Debra Dun.
moisture content before use.
4.4 Grading of Structural Bamboo
4.3.1 Air seasoning of split or half-round bamboo does
not pose much problem but care has to be taken to 4.4.1 Grading is sorting out bamboo on the basis of
prevent fungal discoloration and decay. However, characteristics important for structural utilization as
rapid drying in open sun can control decay due to under:
fungal and insect attack. Seasoning in round form a) Diameter and length of culm,
presents considerable problem for several of Indian
b) Taper of culm,
species of bamboo as regards mechanical degrade due
c) Straightness of culm,
to drying defects.
d) Inter nodal length,
NOTE — A general observation has been that immature bamboo
gets invariably deformed in cross-section during seasoning and
e) Wall thickness,
thick walled immature bamboo generally collapses. Thick f) Density and strength, and
mature bamboo tends to crack on the surface, with the cracks
originating at the nodes and at the decayed points. Moderately g) Durability and seasoning.
thick immature and thin and moderately thick mature bamboos
One of the above characteristics or sometimes
season with much less degrade. Bamboo having poor initial
condition on account of decay, borer holes, etc generally suffers combination of 2 or 3 characteristics form the basis of
more drying degrades. grading. The culms shall be segregated species-wise.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO 9

..
c
x 103
‘1”54

I“4C ●

f
126
I
‘E 1.12 ●

u
\
Xm 0.98
Ln
Ln
UJ
~ o-84 ✎

m ●

●4
~ 0“’7( ● *

z ●
● ● .9.
●

m ! ● ,8* ●
3 ●
●

. *
~ 0.5( ,* ●☛ ● ☛

x ●
●
●
3 ●

●
● 0
● *
● ** ● *

> 0“4 .
● 8
●
● 9*
●

●
z ●

a ●
●

= 0“2 .
●

0.14

s i 1 a I 1
c Q 1 1 1 1

0 10 20 30 40 50 Go Yo eo go 100 110

MOISTURE CONTENT} ‘/0 ~

FIG, 1 MOISTURESTRENGTHRELATIONSHIPBAMBUSANUTANS(BAMBOO)

4.LL2 Diameter and Length 4.4.2.2 The minimum length of culms shall be
preferably 6 m for facilitating close fittings at joints, etc.
4.4.2.1 Gradation according to the mean outer
diameter 4.4.3 Taper

For structural Group Aand Group B species, culms The taper shall not be more than 5.8 mm per metre
shallbe segregatedin steps of 10 mmofmean outer length (or 0.58 percent) of bamboo in any grade of
diameter as follows: bamboo.

Special Grade 70mm<Dianleter <100mm 4.4.4 Curvature


Grade I 50mm<Dian~eter <70mm The maximum curvature shall not be more than 75 mm
Grade II 30mme Diameter <50mm in a length of 6 m of any grade of bamboo.
Grade III Diameter <30mm
4.4.5 Wall Thickness
For structural Group C species culms shall be
Preferably minimum wall thickness of 8 mm shall be
segregated in steps of 20 mm of mean outer diameter
used for load bearing members.
Grade I 80 mm < Diameter <100 mm
4.4.6 Defects and Permissible Characteristics
Grade II 60 mm< Diameter< 80 mm
Grade III Diameter <60 mm 4.4.6.1
Dead and immature bamboos, bore/GHOON

10 NATIONAL BUILDING CODE OF INDIA


holes, decay, collapse, checks more than 3 mm in 5 PERMISSIBLE STRESSES
depth, shall be avoided.
5.1 Basic stress values of different species and groups
4.4.6.2 Protruded portion of the nodes shall be flushed of bamboo shall be determined according to good
smooth. Bamboo shall be used after at least six weeks practice [6-3B(3)]. These values shall then be divided
of felling. Bamboo shall be properly treated in by appropriate factors of safety to obtain permissible
accordance with good practice [6-3 B(2)]. stresses.

4.4.6.3 Broken, damaged and discolored bamboo 5.1.1 The safety factor for deriving safe working
shall be rejected. stresses of bamboo shall be as unde~

4.4.6.4 Matured bamboo of at least 4 years of age shall Extreme fibre stress in beams –4
be used. Modulus of elasticity - 4.5
Maximum compressive stress parallel - 3.5
4.5 Durability and Treatability to grairdfibres
4.5.1 Durability 5.1.2 The coefficient of variation (in percent), which
The natural durability of bamboo is low and varies has been arrived based on data of test-results of at least
between 12 months and 36 months depending on the 15 consignments of bamboo in green conditions, shall
species and climatic conditions. In tropical countries be as under:
the biodeterioration is very severe, Bamboos are
Property Mean Range Maximum
generally destroyed in about one to two years’ time
Expected
when used in the open and in contact with ground --
Value
while a service life of two to five years can be
(1) (2) (3) (4]
expected from bamboo when used under cover and
out of contact with ground. The mechanical strength Modulus of rupture 15.9 5.7- 28.3 23.4
of bamboo deteriorates rapidly with the onset of Modulus of 21.1 12.7 -31.7 27.4
fungal decay in the sclerenchymatous fibres. Split elasticity
bamboo is more rapidly destroyed than round
Maximum 14.9 7.6 – 22.8 20.0
bamboo. For making bamboo durable, suitable compressive stress
treatment shall be given,
The maximum expected values of coefficient of
4.5.2 Ti-datability
variation which are the upper confidence limits under
Due to difference in the anatomical structure of bamboo normality assumption such that with 97.5 percent
as compared to timber, bamboo behaves entirely confidence the actual strength of the bamboo culm will
differently from wood during treatment with beat least 53 percent of the average reported value of
preservative. Bamboos are difficult to treat by normal modulus of rupture in Table 1.
preservation methods in dry condition and therefore 5.2 Solid bamboos or barnboos whose wall thickness
treatment is best carried out in green condition in (w) is comparatively more and bamboos which are
accordance with good practice [6-3 B(2)]. generally known as male bamboos having nodes very
closer and growing on ridges are often considered good
4.5.2.1 Boucherie Process
for structural purposes.
In this process of preservative treatment, water borne
5.3 The safe working stresses for 16 species of
preservative is applied to end surface of green bamboo
bamboos are given in Table 2.
through a suitable chamber and forced through the
bamboo by hydrostatic or other pressure. 5.4 For change in duration of load other than
continuous (long-term), the permissible stresses given
4.5.2.2 Performance of treated bamboo in Table 2 shall be multiplied by the modification
factors given below:
Trials with treated bamboos have indicated varied
durability depending upon the actual location of use. For imposed or medium term loading – 1.25
The performance in partially exposed and under For short-term loading – 1.50
covered conditions is better.
6 DESIGN CONSIDERATIONS
4.5.2.3 For provisions on safety of bamboo structures
against fire, see Part 7 ‘Constructional Practices and 6.1 All structural members, assemblies or framework
Safety’. in a building shall be capable of sustaining, without

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO 11


exceeding the limits of stress specified, the worst c) The structural elements of bamboo shall be
combination of all loadings. A fundamental aspect of appropriately supported near the nodes of
design will be to determine the forces to which the culm as and where the structural system
structure/structural element might be subjected to, demands. The joints in the design shall be
starting from the roof and working down to the soil by located near nodes; and
transferring the forces through various components and d) Bamboo structures be designed like any other
connections, Accepted principles of mechanics for conventional structural elements taking care
analysis and specified design procedures shall be of details with regards to supports and joints;
applied (see Part 6 ‘Structural Design, Sub-section 3A they shall be considered to generally act as a
Timber’). hinge, unless substantiating data justify a
6.2 Unlike timber, bamboo properties do not relate fixed joint.
well to species, being dependent among other factors,
6.6 Flexural Members
on position of the culm, geographic location and age.
The practice in timber engineering is to base designs 6.6.1 All flexural members maybe designed using the
on safe working stresses and the same maybe adopted principles of beam theory.
to bamboo with the limitations that practical experience
6.6.2 The deflection shall be within the prescribed
rather than precise calculations generally govern the
detailing. limits. The tendency of bamboo beams to acquire a
large deflection under long continuous loadings due
6.3 Net Section to possible plastic flow, if any shall be taken care of.
Permanent load may be doubled for calculation of
It is determined by passing a plane or a series of
deflection under sustained load (including creep) in
connected planes transversely through the members,
case of green bamboo having moisture content
Least net sectional area is used for calculating load
exceeding 15 percent.
carrying capacity of a member.
6.6.3 Bamboo is not naturally reinforced for
6.4 Loads shear, because, compared to reinforced cement
6.4.1 The loads shall be in accordance with Part 6 concrete beam, the stirrups are located on the
‘Structural Design, Section 1 Loads, Forces and longitudinal instead of the transverse direction in a
Effects’. bamboo culm.

6.4.2 The worst combination and location of loads 6.6.4 The moment of inertia, Zshall be determined as
shall be considered for design. Wind and seismic forces follows:
shall not be considered to act simultaneously. a) The outside diameter and the wall thickness
shrdl be measured at both ends, correct up to
6.5 Structural Forms
1 mm for diameter of culm and 0.1 mm for
6.5.1 Main structural components in bamboo may the wall thickness. (For each cross-section the
include roof and floor diaphragms, shear walls, wall diameter shall be taken twice, in direction
panellings, beams, piles, columns, etc. Both from the perpendicular to each other and so the wall
point of view of capacity and deformation, trusses and thickness shall be taken as four times, in the
framed skeltons are much better applications of same places as the diameter has been taken
bamboo. twice.)

6.5.2 Schematization of Bamboo as a Structural b) With these values the mean diameter and the
Material mean thickness for the middle of the beam
shall be calculated and moment of inertia
This shall be based on the principles of engineering determined.
mechanics involving the following assumptions and
practices: 6.6.4.1 The maximum bending stress shall be
calculated and compared with the allowable stress.
a) The elastic behaviour of bamboo, till failure;
(plastic behaviour being considered 6.6.4.2 The deflection shall be calculated, and
insignificant); compared with the allowable deflection. The initial
curvature shall be considered in the calculation of the
b) Bamboo culms are analysed on mean wall
deflection.
thickness basis as hollow tube structure (not
perfectly straight) member on mean diameter 6.6.4.3 The shear stress in the neutral layer at the small
basis: end shall be checked, if the length of the beam is less

12 NATIONAL BUILDING CODE OF INDIA


than 25 times the diameter at that end. For shear checks, 6.8.2 A truss is essentially a plane structure which is
conventional design procedure in accordance with very stiff in the plane of the members, that is the plane
Part 6 ‘Structural Design, Sub-section 3A Timber’ in which it is expected to carry load, but very flexible
shall be followed. in every other direction. Roof truss generally consists
NOTE — The basic shear stress values (N/mm2) for at least of a number of triangulated frames, the members of
five species of bamboo in split form in green condition have which are fastened at ends and the nature of stresses at
been determined as under: joints are either tensile or compressive and designed
Bambusa pallida 9.77 as pin-ended joints (see Fig. 2A). Bamboo trusses
B. Vulgaris 9.44 may also be formed using bamboo mat board or
Dedroculumus giganteous 8.86 bamboo mat-veneer composite or plywood gusset (see
D.humiltonii 7.77 Fig. 2B).
Oxytenanthera abyssinicia 11.2
6.8.3 Truss shall be analysed from principles of
6.6.4.4 Forces acting on a beam, being loads or structural mechanics for the determination of axial
reaction forces at supports, shall act in nodes or as near forces in members. For the influence of eccentricities,
to nodes as by any means possible. due allowance shall be made in design.
6.8.4 The truss height shall exceed 0.15 times the span
6.7 Bamboo Columns (Predominantly Loaded in
in case of a triangular truss (pitched roofing) and
Axial Direction)
0.10 times the span in case of a rectangular (parallel)
6.7.1 Columns and struts are essential components truss.
sustaining compressive forces in a structure. They
6.8.5 For members in compression, the effective
transfer load to the supporting media.
length for in-plane strength verification shall be
6.7.2 Design of columns shall be based on one of the taken as the distance between two adjacent points
following two criteria: of contraflexure. For fully triangulated trusses,
effective length for simple span members without
a) Full scale buckling tests on the same species,
especially rigid end-connection shall be taken as the
size and other relevant variables.
span length.
b) Calculations, based on the following:
6.8.6 For strength verification of members in
1) The moment of inertia shall be as per6.6.4.
compression and connections, the calculated axial
2) For bamboo columns the best available
forces should be increased by 10 percent.
straight bamboo culms shall be selected.
Structural bamboo components in 6.8.7 The spacing of trusses shall be consistent with
compression should be kept under a use of bamboo purlins (2 m to 3 m).
slenderness ratio of 50.
6.8.8 The ends in open beams, joists, rafters, purlins
3) The bending stresses due to initial shall be suitably plugged. Bamboo roof coverings shall
curvature, eccentricities and induced be considered as non-structural in function. The
deflection shall be taken into account, in common roof covering shall include bamboo mat
addition to those due to any lateral board, bamboo mat corrugated sheet, bamboo tiles/
load. strings, plastered bamboo reeds, thatch, corrugated
6.7.3 Buckling calculation shall be according to Euler, galvanized iron sheeting, plain clay tiles or pan tiles,
with a reduction to 90 percent of moment of inertia, to etc.
take into account the effect of the taper provided it is 7 DESIGN AND TECHNIQUES OF JOINTS
not less than 0.6 percent.
7.1 Connecting the load+mring elements together for
6.7.4 For strength and stability, larger diameter thick effective transfer of stress is one of the serious problems
walled sections of bamboo with closely spaced nodes confronted by the engineers. The size of the members
shall be used, Alternatively, smaller sections may be in a structure depends not only on the direct loads they
tied together as a bundle-column. are required carry, but also on the ability to join the
members together. Joints are quite critical in
6.8 Assemblies, Roof Trusses
assemblies, and these should be stable in relation to
6.8.1 Elements in structure are generally built-up in time. The main objective is to achieve continuity
the form of assembled members for which a triangle is between elements with controlled displacements. As
a simple figure of stability. Besides sloped chords, joints are a source of weakness in any bamboo
parallel chord construction is also appropriate as structure, they have to be made as strong and rigid as
external profile. possible.

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO 3B BAMBOO 13


i

u
2A - PIN ENDED JOINT TRUSSES

/-GUSSET (TYPICAL)

2B GUSSET JOINT TRUSSES

FIG. 2 SOMETYPICALCONFIGURATIONS
FORSMALLANDLARGETRUSSES
INBAMBOO

14 NATIONAL BUILDING CODE OF INDIA

..
7.2 Bamboo Joints similar diameter and cut longitudinally to half depth
over at least one internode length and fastened as per
Efficient jointing is basic to the structural adequacy of
full lap joint (see Fig. 3).
a framed construction, may it be of any cellulosic
material. Round, tubular form of bamboo requires an 7.2.1.1.2 Butt joints
approach different to that used for sawn timber.
Culms of similar diameter are butted end to end, inter-
Susceptibility to crushing at the open ends, splitting
connected by means of side plates made of quarter-
tendency, variation in diameter, wall thickness and
round culm of slightly large diameter bamboo, for two
straightness are some of the associated issues which
or more internode lengths. Assembly shall be fixed
have to be taken care of while designing and detailing
and tied preferably with dowel pins. This joint transfers
the connections with bamboo.
both compressive and tensile forces equrdly well (see
7.2.1 Traditional Practices Fig. 4).

Such joining methods revolve around lashing or tying 7.2.1.1.3 Sleeves and inserts
by rope or string with or without pegs or dowels. Such
Short length of bamboo of appropriate diameter may
joints lack stiffness and have low efficiency.
be used either externally or internally to join two culms
7.2.1.1 Lengthening joints (end jointing) together (see Fig. 5).

7.2.1.1.1 Lap joint 7.2.1.1.4 Scarfjoints

In this case, end of one piece of bamboo is made to lap A scarf joint is formed by cutting a sloping plane 1 in
over that of the other in line and the whole is suitably 4 to 6 on opposite sides from the ends of two similar
fastened. It maybe full lapping or half lapping. Full diameter bamboo culms to be joined. They shall be
section culms are overlapped by at least one internode lapped to form a continuous piece and the assembly
and tied together in two or three places. Efficiency suitably fastened by means of lashings. Using hooked
could be improved by using barnboo or hardwood splays adds to the strength and proper location of joints
dowels. In half lapping, culms shall preferably be of (see Fig. 6).

b I i
II
i i
I
I u II u II I
3A FULL - LAPPED SPLICED JOINT
(OVER - LAPPED ATLEAST ONE lNTERNOtIE) HARD&&D\%Wfi
7/
n n
Ill 181 Ill Ill
Ill Ill Ill Ill
I
I Ill
Ill
u
Ill
Ill
Ill
Ill
u
Ill
Ill

3B HALF - LAPPED SPLICED JOINT ‘f


(SIMILAR DIAMETER; ONE INTERNODE LENGTH)
;,

n
I ,
II
I
II
II
I

3C LAPPED SPLICED JOINT WITH PEGS AND BATTENS

FIG. 3 LAP JOINTSIN BAMBOO

PART 6 STRUCTUIWL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO 15


-q

FOR DOWELS
OR PINS

I
I

FIG. 4 BUTT JOINTWITH SIDE PLATES IN BAMBOO

—l——
!
I
I
) ._J— —

LENGTHENING JOINT

FIG. 5 SLEEVESAND INSERTSFOR BAMBOO JOINTS

L-=LD-l
FIG. 6 SCARF JOINT

NATIONAL BUILDING CODE OF INDIA

..

.
7.2.1.2 Bearing joints 7.2.1.2.2 Tenon joint

For members which either bear against the other or It is formed by cutting a projection (tenon) in walls of
cross each other and transfer the loads at an angle other one piece of bamboo and filling it into corresponding
than parallel to the axis, bearing joints are formed. holes (mortise) in another and keyed. It is a neat and
versatile joint for maximum strength and resistance to
7.2.1.2.1 Butt joints
separation (see Fig. 8).
The simplest form consists of a horizontal member
7.2.1.2.3 Cross over joint
supported directly on top of a vertical member. The
top of the post may be cut to form a saddle to ensure It is formed when two or more members cross at right
proper seating of beam for good load transfer. The angles and its function is to locate the members and
saddle should be close to a node to reduce risk of to provide lateral stability. In case of the joint
splitting (see Fig. 7). connecting floor beam to post, it maybe load bearing

I i
I SQUARE
! : NOTCHED

HORIZONTAL MEMBER

D o
VERTICAL
MEMBER

‘HOLE FOR PIN

%IDE PLATE
7A SADDLE (BUIT) JOINT
(SADDLE TO BE CLOSE TO THE
7B VARIATIONS ON SADDLE JOINT
NODE )

FIG. 7 BUTT JOINTSIN BAMBOO

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO


.

AND KEY JOINT

INTEGRAL TENON (HORNED) JOINT

FIG. 8 TENONJOINT

(see Fig. 9). Such joints are also used to transmit angle Alternatively steel bands clamps with integral
thrust. bolt/eye may be fitted around bamboo
sections for jointing.
7.2.1.3 Angled joints
7.2.3 Fixing Methods and Fastening Devices
When two or more members meet or cross other than
at right angles, angled joints are formed. For butt joints, In case of butt joints the tie maybe passed through a
the ends of the members may be shaped to fit in as pre-drilled hole or around hardwood or bamboo pegs
saddle joints. Tenons would help in strengthening such or dowels inserted into prefomed holes to act as horns.
joints (see Fig. 10). Pegs are driven from one side, usually at an angle to
increase strength and dowels pass right through the
7.2.2 Modern Practices (see Fig. 11)
member, usually at right angles. ,
Following are some of the modern practices for
7.2.3.1 Normally 1.60 mm diameter galvanized iron
bamboo jointing:
wire may be used for tight lashing.
a) Plywood or solid timber gusset plates maybe
7.2.3.2 Wire bound joints
used at joint assemblies of web and chord
connection in a truss and fixed with bamboo Usually galvanized iron 2.00 mm diameter galvanized
pins or bolts. Hollow cavities of bamboo need iron wire is tightened around the joints by binding the
to be stuffed with wooden plugs. respective pieces together. At least two holes are drilled
b) Use of wooden inserts to reinforce the ends in each piece and wire is passed through them for good
of the bamboo before forming the joints. results.

NATIONAL BUILDING CODE OF INDIA


PURLIN NODE

w
On 1
-. DOWEL
6. II
-- \\ II
-- u
2+
.-

W \.FTERx I

~\ BEAM SUPPORTED ON SHORT


CULM TIED TO POST

(—

DOWELLED AND PEGGED AND


TIED JOINT TIED JOINT

PURLIN

I
.-.
(

RAFTER

ALTE~NATIVE PURLIN - RAFTER CONNECTION

FIG. 9 CROSSOVER JOINTS(BEARINGJoIms)

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO 3B BAMBOO 19


FIG. 10 ANGLEDJOINTWITHINTEGRALTENONS

FIG. 11 GUSSETPLATEDJOiNTS

7.2.3.3 Pinandwire bot+ndjoints load and geometry, description of all fastening


elements, their sizes and location shall be indicated.
Generally 12 mm dia bamboo pins are fastened to
Data shall be based on full scale tests.
culms and bound by 2.00 mm diameter galvanized iron
wire. 7.2.5 Tests on full scale joints or on components shall
be carried out in a recognized laboratory.
7.2.3.4 Fish plateslgusset plated joints
7.2.6 In disaster high wind and seismic areas, good
At least 25 mm thick hardwood splice plate or 12 mm
construction practice shall be followed taking care of
thick structural grade plywood are used. Solid bamboo
joints, their damping and possible ductility. Bracings
pins help in fastening the assembly.
in walls shall be taken care of in bamboo structures.
7.2.3.5 Horned joints
8 STORAGE OF BAMBOO
Two tongues made atone end of culm may be fastened
Procurement and storage of bamboo stocks are
with across member with its mortise grooves to receive
essential for any project work and shall be done in
horns, the assembly being wire bound.
accordance with Part 7 ‘Constructional Practices and
7.2.4 For any complete joint alternative for a given Safety’. -

20 NATIONAL BUILDING CODE OF INDIA


ANNEX A
(Foreword)
SOURCE AND LOCAL NAMES OF SOME OF THE SPECIES OF BAMBOO

S1No. Species Source/L.oeal Names

(1) (2) (3)

1. Bambusa auriculata Assam, Bangladesh, Myanmw, introduced in Calcutta


Botanic Garden.

2. B. balcooa Asm — Baluka;


Ben — Balku bans;
Duars — Bora bans;
Garo — Wamnah, beru;
Tripura — Barak.

3. B. bambos (Syn. B. arundinacea) Asm — Kotoba;


Ben — Baroowa, behor; ketuas; ketwa
Manip — Saneibi;
Mah — Katang bamboo, oowg%
Oriya — Daba, katuig;
Tel — Mulkas veduru, Mullu vedurn;
English — Spiny bamboo.

4. B. burmanica Asm — Thaikawa.

5. B. multiplex Saris — keu-f%


Syn. B. glancescens (Syn. B. nana) Burmese — Pa-lau-pimm-wa;
Malay — Bamboo tjeenah;
China — Bamboo hewer tjeenah.

6. B. nutans Assam — Deobans, jotia-makal;


Asm — Bidhuli, mukkd;
Ben — Makia;
Bhutia — Jiu;
Hin — Malabans;
Kangra — Nal;
Khasi — Seringjti,
Kuki — Wa malang;
Lepcha — Malubans, mahlu, mallo;
Oriya — Badia bansa;
Sylhet (Banglaesh) — Peechlfi
Tripura — Kali

7. B. pallida Asm — Bijli, jowa, makal, walkthai;


Cacha.r — Bakhal, burwal;
Khasi — Seskien, skhen, ineng, uskeu
Lepcha — Pashipo, pshi, pushee;
Mikir — Loto;
Naga — Tesero, watoi;
Tripura — Makal.

8. B. polymoipha Asm — Jama betwa, betswx


Ben — Batua, jaibarouw~ jamw
Burma — Kyathaung-wa;
MP-Korku — Narangi bhas;
Tripura — Basi.

9. B. tulda Asm — Wamunna, wagi, nal-bans;


Beng — Tulda, jow%
Duars — Karanti, matela;
Garo — Watti;
Hin — Peka;
Kamrup — Bijuli, jati, joo, ghorw
Tripura — Mirtinga

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO 21


(1) (2) (3)

10. B. vulgaris Ben and Manipuri — Bakal;


Oriya — Sunarkania bans.

11. B. Wamin Syn. B. ventricosa Common name — Pitcher bamboo.


(Syn. B. Vulgaris var. Wamin)
12. Cephalostachyum pergacile MP — Bhalan bans;
Manipuri — Wootang;
Naga — Latang;
Oriya — Darrgi.

13. Dendrocalamus .giganteous English — GiantBamboo;


Asm — Worra;
Manipuri — Maroobeb.

14. D. hamiltonii Nep — Tame;


Asm — Kokwa;
Tripura — Pecha.

15. D. longispathus Tripura — Rupai.

16. D. membranaceus Native of Myanmar; introduced in Kerala.

17. D. strictus English — Male bamboo;


Ben — Karail;
Guj — Nakur bans;
Kan — Kiri bidiru;
Mah — Male barnboo, nanvet
Oriya — Salia;
Tam — Kalmungil;
Tel — Sadanapa vedur;
Tripura — Lathi bans;
FIin — Bans Kaban, nav bans;

18. A4elocanna baccifera Asm — Tarai;


Ben — Muli;
Cachar — Wati;
Garo — Watrai;
Manipuri — Moubi;
Mikir — Artern,
Naga — Turiah.

19. Oxytenanthera abyssinicia Native of tropical AfricW cultivated at I?RI, Debra Dun.

20. Thyrsostachys oliveri Native of Myanmar; Planted in Haldwani (Uttaranchal);


Arunachal Pradesh, Kerala and Tamil Nadu.

NOTES
1 The following abbreviations have been used in the above table:
Asm — Assam
Ben — Bengali
Guj — Gujarati
Hin — Hindi
Kan — Kannada
Mab — Maharashtra
Manip — Marripur
MP — Madhya Pradesh
Nep — Nepali
Saris — Sanskrit
2 The above Vdbledoes not provide an exhaustive list. It only attempts to entist some of the information readily available in regard to
species of bamboo from India and some of the neighbounng countries, and some connected information.

22 NATIONAL BUILDING CODE OF INDIA


LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’
(1) 6874:1973 Method of test for round bamboo
in the fulfillment of the requirements of this Code. The
latest version of a standard shall be adopted at the time (2) 9096:1979 Code of practice for preservation
of enforcement of the Code. The standards listed may of bamboo for structural purposes
be used by the Authority as a guide in conformance (3) 6874:1973 Method of test for round bamboo
with the requirements of the referred clauses in the
8242:1976 Method of test for split bamboo
Code.

.-

PART 6 STRUCTURAL DESIGN — SECTION 3 TIMBER AND BAMBOO: 3B BAMBOO 23


. ---
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 4 Masonry

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE . .. 5
2 TERMINOLOGY ... 5
3 MATERIALS ... 7
4 DESIGN CONSIDERATIONS ... 9
5 STRUCTURAL DESIGN ... 18
6 GENERAL REQUIREMENTS . .. 22
7 SPECIAL CONSIDERATION IN EARTHQUAKE ZONES . .. 24
8 GUIDELINES FOR IMPROVING EARTHQUAKE RESISTANCE OF ... 33
LOW STRENGTH MASONRY BUILDINGS
9 REINFORCED BRICK AND REINFORCED BRICK CONCRETE FLOORS ... 38
AND ROOFS
10 NOTATIONS AND SYMBOLS ... 38

ANNEX A SOME GUIDELINES FOR ASSESSMENT OF ECCENTRICITY ... 39


OF LOADING ON WALLS
ANNEX B CALCULATION OF BASIC COMPRESSIVE STRESS OF ... 39
MASONRY BY PRISM TEST
ANNEX C GUIDELINES FOR DESIGN OF MASONRY SUBJECTED TO . .. 40
CONCENTRATED LOADS
ANNEX D GUIDELINES FOR APPROXIMATE DESIGN OF NON-LOAD ... 41
BEARING WALL
ANNEX E NOTATIONS, SYMBOLS AND ABBREVIATIONS ... 42

LIST OF STANDARDS . .. 42

2 NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Section primarily covers the structural design of unreinforced masonry elements in buildings. However,
provisions on reinforced brick and reinforced brick concrete floors and roofs have also been included.

This Section was first published in 1970 and revised in 1983. Subsequently the first revision of this Section was
modified in 1987 through Amendment No. 2 to bring this Section in line with the latest revised masonry Code. In
this amendment, certain provisions were updated following the revision of IS 1905 ‘Code of practice for structural
use of unreinforced masonry’ on which the earlier version was based. In the amendment, requirements of masonry
element for stability were modified; in the design of free standing wall, provisions were made for taking advantage
of the tensile resistance in masonry under certain conditions; provision regarding effective height of masonry
wall between openings was modified; method of working out effective height of wall with a membrane type
DPC was modified; the criteria for working out effective length of wall having openings was modified; some
general guidelines for dealing with concentrated loads for design of walls were included; and provision of cutting
and chases in walls were amplified.

As a result of experience gained in the implementation of this Section and feedback received, as well as in view
of revision of IS 4326 ‘Code of practice for earthquake resistant design and construction of buildings’ and
formulation of some new standards in this field, a need to revise thk Section has been felt. This revision has,
therefore, been prepared to take care of these aspects. The significant changes incorporated in this revision
include the following:

a) The provision of special considerations in earthquake zones have been aligned in line with IS 4326:1993.
b) Anew clause covering guidelines for improving earthquake resistance of low strength masonry buildings
has been added.
c) Reference to design of reinforced brick and reinforced brick concrete floors and roofs has been included.
d) Reference to all the concerned Indian Standards have been updated.

Structural design requirements of this Section are based on IS 1905:1987 ‘Code of practice for structural use of
unreinforced masony (third revision)’ and IS 4326: 1993 ‘Code of practice for earthquake resistant design and
construction of buildings (second revision)’.

A reference to SP 20:1991 ‘Handbook on masonry design and construction (first revision)’ maybe useful.

All standards, whether given herein above or cross-refereed to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 3


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN
Section 4 Masonry

1 SCOPE shall be determined to the outside of the coring but


cross-sectional area of grooves shall not be deducted
1.1 This Section primarily covers the structural design
from the gross cross-sectional area to obtain the net
aspects of unreinforced load bearing and non-load
cross-sectional area.
bearing walls, constructed with masonry units
permitted in accordance with this Section. This, 2.1.5 Curtain Wall — A non-load bearing wall subject
however, also covers provisions for design of to lateral loads. It may be laterally supported by vertical
reinforced brick and reinforced brick concrete floors or horizontal structural members where necessary (see
and roofs. It also covers guidelines regarding Fig. 2).
earthquake resistance of low strength masonry
2.1.6 Eflective Height — The height of a wall or
buildings.
column, to be considered for calculating slenderness
1.2 The recommendations of the Section do not apply ratio.
to walls constructed in mud mortars.
2.1.7 Effective Length — The length of a wall to be
2 TERMINOLOGY considered for calculating slenderness ratio.

2.1 For the purpose of this Section, the following 2.1.8 Effective Thickness — The thickness of a wall .
definitions shall apply. or column to be considered for calculating slenderness
ratio.
2.1.1 Bed Block — A block bedded on a wall, column
or pier to disperse a concentrated load on a masonry 2.1.9 Hollow Unit — A masonry unit of which net
element. cross-sectional area in any plane parallel to the bearing
surface is less than 75 percent of its gross cross-
2.1.2 Bond — Arrangement of masonry units in sectional area measured in the same plane.
successive courses to tie the masonry together both
longitudinally and transversely; the arrangement is 2.1.10 Grout — Mortar of pourable consistency.
usually worked out to ensure that no vertical joint of 2.1.11 Joint — A junction of masonry units.
one course is exactly over the one in the next course
above or below it, and there is maximum possible a) Bed joint — A horizontal mortar joint upon
amount of lap. which masonry units are laid.
b) Cross joint — A vertical joint, normal to the
2.1.3 Column, Pier and Buttress
face of the wall.
a) Column — An isolated vertical load bearing c) Wall joint — A vertical joint parallel to the
member, width of which does not exceed four face of the wall.
times the thickness.
2.1.12 Leaf — Inner or outer section of a cavity wall.
b) Pier — A thickened section forming integral
part of a wall placed at intervals along the 2.1.13 Lateral Support — A support which enables a
wall, to increase the stiffness of the wall or to masonry element to resist Iateral load and/or restrains
carry a vertical concentrated load. Thickness lateral deflection of a masonry element at the point of
of a pier is the overall thickness including the support.
thickness of the wall or, when bonded into a 2.1.14 Load Bearing Wall ~ A wrdl designed to carry
leaf of a cavity wall, the thickness obtained an imposed vertical load in addition to its own weight,
by treating that leaf as an independent wall together with any lateral load.
(see Fig. 1).
2.1.15 Masonry — An assemblage of masonry units
c) Buttress — A pier of masonry built as an
properly bonded together with mortar.
integral part of wall and projecting from either
or both surfaces, decreasing in cross-sectional 2.1.16 Masonry Unit — Individual units which are
area from base to top. bonded together with the help of mortar to form a
masonry element such as wall, column, pier, buttress,
2.1.4 Cross-Sectional Area of Masonry Unit — Net
etc.
cross-sectional area of a masonry unit shall be taken
as the gross cross-sectional area minus the area of 2.1.17 Partition Wall — An interior non-load bearing
cellular space. Gross cross-sectional area of cored units wall, one storey or part storey in height.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 5


WIDTH OF PIER, Wp WIDTH OF PIER, Wp

FIG. 1 DEFINITIONOF PIER

HINGED JOINT
(DIAGRAMMATIC)

RCC COLUMN

CURTAIN
WALL

i-i
~

FIG. 2 MASONRYCURTAINWALL

2.1.18 Panel Wall — An exterior non-load bearing each leaf being ,lxdt of mason@ units and
wall in framed construction, wholly supported at each separated by a cavity and tied together with
storey but subjected to lateral loads. metal ties or bonding units to ensure that the
2.1.19 Shear Wall — A wall designed to carry two leaves act as one structural unit, the space
horizontal forces acting in its plane with or without between the leaves being either left as
vertical imposed loads. continuous cavity or filled with a non-load
bearing insulating and water-proofing
2.1.20 Slenderness Ratio — Ratio of effective height
material.
or effective length to effective thickness of a masonry
b) Faced wall — A wall in which facing and
element.
backing of two different materials are bonded
2.1.21 Types of Walls together to ensure common action under load
a) Cavity wall — A wall comprising two leaves, (see Fig. 3).

6 NATIONAL BUILDING CODE OF INDIA


I I
I
I I

1 I 1 1

1=1 I
I ‘CONCRETE BACKING
\ \

L STONE FACING
‘EIRiCK BACKING ‘STONE FACING

BLOCK

FIG. 3 TYPICALFACEDWALL

NOTE — To ensure monolithicaction in faced walls, 3.2.1 Masonry units may be of the following types:
shearstrengthbetweenthe facing and the backingshall
be provided by toothing, bonding or other means. a) Common burnt clay building bricks,
c) Veneered wall — A wall in which the facing b) Burnt clay fly asp building bricks,
is attached to the backing but not so bonded
c) Pulverized fuel ash lime bricks,
as to result in a common action under load.
d) Stones (in regular sized units),
3 MATERIALS e) Sand-lime bricks,
3.1 General f) Concrete blocks (solid and hollow),
The materials used in masonry construction shall be g) Lime based blocks,
in accordance with Part 5 ‘Building Materials’. h) Burnt clay hollow blocks,
3.2 Masonry Units j) Gypsum partition blocks,

Masonry units used in construction shall conform to k) Autoclave cellular concrete blocks, and
accepted standards [6-4(1)]. m) Concrete stone masonry blocks.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 7


NOTES and conform to this Section for similar new masonry
1 Gypsum partition blocks are used only for units.
construction of non-load bearing partition walls.
2 Use of other masonry units, such as, precise stone 3.3 Mortar
blocks, fly-ash-lime-gypsum bricks, stabilized mud blocks
and other bricks/blocks not covered by the above Mortar for masonry shall conform to accepted standard
specifications may also be permitted based on test results. [6-4(2)].
3.2.2 Masonry units that have been previously used 3.3.1 Mix proportions and compressive strengths of
shall not be re-used in brickwork or blockwork some of the commonly used mortars are given in
construction, unless they have been thoroughly cleaned Table 1.

Table 1 Mix Proportions and Strength of Mortars for Masonry


(Clause 3.3.1)

S1 Grade of Mix Proportions (by Loose Volume) Mhinmm Compressive


No. Mortar A Strength at 28 Days
/ *
Cement Lime Lime Pozzolana Pozzohma Sand in N/mm*
Mixture
(1) (2) (3) (4) (5) (6) (7) (8)

1 H] 1 lACor B o 0 3 10
2(a) H2 1 lACor B 0 0 4 7.5
2(b) 1 1/2C or B 0 0 4% 6.0

3(a) Ml 1 0 o 5 5.0
3(b) 1 lCor B 0 0 6 3.0
3 (c) 0 o 1 (LP-40) 0 1?’42 3.0

4(a) M2 1 0 0 o 6 3.0
4(b) 1 2B 0 0 9 2.0
4(c) 0 1A 0 0 2 2.0
4(d) 0 lB 0 1 1 2.0
4!e ) 0 lCor B 0 2 0 2.0
4(f) 0 o 1 (LP-40) 0 134 2.0 .
*
s(a) M3 1 0 0 o 7 1.5
5(h) 1 3B 0 0 12 1.5
5(C) 0 1A 0 0 3 1.5
5(d) 0 lB 0 2 1 1.5
5(C) 0 lCor B 0 3 0 1.5
5(f-) 0 o 1 (LP-40) 0 2 1.5

6(a) L1 1 0 0 o 8 0.7
6(b) 0 lB 0 1 2 0.7
6(c) 0 lCor B 0 2 1 0.7
6(d) 0 o 1 (LP-40) 0 2% 0.7
6(e) 0 0 1 (LP-20) 0 1Y2 0.7

7(U) L2 o lB 0 o 3 0.5
7(b) 0 lCor B 0 1 2 0.5
7(C) 0 o 1 (LP-7) 0 1% 0.5

NOTES
1 Sand for making mortar should be well graded. In case sand is not well graded, its proportion shall be reduced in order to achieve
the minimum specified strength.
2 For mixes in S1 No. 1 and 2, use of lime is not essential from consideration of strength as it does not result in increase in strength.
However, its use is highly recommended since it improves workability.
3 For mixes in S1 No. 3(a), 4(a), 5(a) and 6(a), either lime C or B to the extent of% part of cement (by volume) or some plasticizer
$hou ld be added for improving workability. t
4 For mixes in S1 No. 4(b) and 5(b), lime and sand should first be ground in mortar mill and then cement added to coarse stuff.
5 It is essential that mixes in S1 No. 4(c), 4(d), 4(e), 5(d), 5(e), 6(b), 6(c), 7(a) and 7(b) are prepared by grinding in a mortar mill.
6 Mix in S1 No. 2(b) has been classified to be of same grade as that of S1 No. 2(a), mixes in S1 No. 3(b) and 3(c) same as that in
S1 No. 3(a), mixes in S1 No. 4(b) to 4(f) same as that in S1 No. 4(a), even though their compressive strength is less. This is from
consideration of strength of masonry using different mix proportions.
7 A, B and C denote eminently hydraulic lime, semi-hydraulic lime and fat lime respectively, as specified in appropriate standards
listed in Part 5 ‘Building Materials’.

8 NATIONAL BUILDING CODE OF INDIA

..
4 DESIGN CONSIDERATIONS a) In case of a wall, where slenderness ratio is
based on effective height, any of the following
4.1 General
constructions are provided:
Masonry structures gain stability from the support 1) RCC floor/roof slab (or beams and slab)
offered by cross walls, floors, roof and other elements, irrespective of the direction of span, bears
such as, piers and buttresses. Load bearing walls are on the supported wall as well as cross
structurally more efficient when the load is uniformly walls, to the extent of at least 90 mm;
distributed and the structure is so planned that 2) RCC floor/roof slab not bearing on the
eccentricity of loading on the members is as small as supported wall or cross wall is anchored
possible. Avoidance of eccentric loading by providing to it with non-corrodible metal ties of
adequate bearing of floor/roof on the walls providing 600 mm length and of section not less
adequate stiffness in slabs and avoiding fixity at the than 6 mm x 30 mm, and at intervals not
supports, etc, is especially important in load bearing exceeding 2 m, as shown in Fig. 4; and
walls in multi-storey structures. These matters should
receive careful consideration during the planning stage A
50 mm
of masonry structures.
. ,. .... , . , . - - .’:... ~ ...<........
4.2 Lateral Supports and Stability
.. .
4.2.1 Lateral Supports \ ... Y,
Lateral supports for a masonry element, such as, load
-.
bearing wall or column are intended:

a) to limit slenderness of a masonry element so


as to prevent or reduce possibility of buckling
A = Cement concrete only at places where anchors are
of the member due to vertical loads; and
provided (200 mm in width in the direction
b) to resist horizontal components of forces so perpendicular to the plane of paper)
as to ensure stability of a structure against
overturning. FIG. 4 ANCHORINGOF RCC SLABwrrH MASONRY
WAU (WHENSLAB DOESNOT BEAR ON WALL)
4.2.1.1 Lateral support may be in the vertical or
horizontal direction, the former consisting of floor/roof
3) Timber floor/roof, anchored by non-
bearing on the wall or properly anchored to the same
corrodible metal ties of length 600 mm
and latter consisting of cross walls, piers or buttresses.
and of minimum section 6 mm x 30 mm,
4.2.1.2 Requirements of 4.2.l(a) from consideration of securely fastened to joists and built into
slenderness may be deemed to have been met with, if walls as shown in Fig. 5 and Fig. 6. The

CONCRETE, min. CONCRETE, min.


LEN

METAL ANCHO
LONG, FIXED

5A JOISTS AT RIGHT ANGLE TO WALL 5B JOISTS PARALLEL TO WALL

FIG. 5 TYPICAL DETAILS FOR ANCHORAGE OF SOLID WALLS

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 9


CONCRETE, min. LENGTH 300 mm ~

(i) (ii)
6 A TIMBER JOISTS AT RIGHT ANGLES TO WALL

-.

M
FI

(i) (ii)

6 B TIMBER JOISTS PARELLEL TO WALL

BETWEEN CONCRETE UNITS


(i) (ii)

6 C PRECAST CONCRETE FLOOR UNITS PARALLEL TO WALL

FIG. 6 TYPICAL DETAILS FOR ANCHORAGE OF CAVITY WALLS

10 NATIONAL BUILDING CODE OF INDIA


anchors shall be provided in the direction support from consideration of stability, if the
of span of timber joists as well as in its construction providing the support is capable of
perpendicular direction, at intervals of resisting some of the following forces:
not more than 2 m in buildings up to two
a) Simple static reactions at the point of lateral
storeys and 1.25 m for buildings more
support to all the lateral loads; plus
than two storeys in height.
b) 2.5 percent of the total vertical load that the
NOTES
wall or column is designed to carry at the point
1 In case precast RCC units are used for floors
of lateral support.
and roofs, it is necessary to interconnect them and
suitably anchor them to the cross walls so that 4.2.2.1 For the purpose specified in 4.2.2, if the lateral
they can transfer lateral forces to the cross walls.
supports are in the vertical direction, these should meet
2 In case of small houses of conventional designs, the requirements given in 4.2.l.2(a) and should also
not exceeding two storeys in height, stiffening
be capable of acting as horizontrd girders duly anchored
effect of partitions and cross walls is such that
metal anchors are normally not necessary in case to the cross wall so as to transmit the lateral loads to
of timber floor/roof and precast RCC floor/roof the foundations without exceeding the permissible
units. stresses in the cross walls.
b) In case of a wall, when slenderness ratio
4.2.2.2 In case of load bearing buildings up to four
is based on its effective length; a cross
storeys, stability requirements of 4.2.2 maybe deemed
wall/pier/bttttress of thickness equal to or
to have been met with, if
more than half the thickness of the
supported wall or 90 mm, whichever is a) height to width ratio of building does not
more, and length equal to or more than exceed 2;
one-fifth of the height of wall, is built at b) cross walls acting as stiffening walls
right angle to the wall (see Fig. 7) and continuous from outer wall to outer wall or
bonded to it according to provision outer wall to a load bearing inner wall, and of
of 4.2.2.2 (d); thickness and spacings as given in Table 2
are provided. If stiffening wall or walls that
are in a line, are interrupted by openings,
length of solid wall or walls in the zone of
the wall that is to be stiffened shall be at least
one-fifth of height of the opening as shown
in Fig. 8;
c) floors and roof either bear on cross walls or
are anchored to those walls as in 4.2.1.2 such
that all lateral loads are safely transmitted
WHICHEVER II
to those walls and through them to the
foundation; and
FIG. 7 MINIMUM DIMENSION FOR MASONRY WALL
Table 2 Thickness and Spacing of
OR BUTTRESS EFFECTIVE LATERAL SUPPORT
Stiffening Walls
c) In case of a column, an RCC or timber [Clause 4.2.2.2(b)]
beam/R S joisthoof truss, is supported on
the column. In this case, the column will S1 Thictmeas Height 1) Stiffening Walt 1)
not be deemed to be laterally supported No. of Load of !ltorey ~
Bearing Not to Thicknessnot Maximum
in the direction at right angle to it; and Walt to be Exceed “ less than spacing
d) In case of a column, an RCC beam Stiffened ~
forming a part of beam and slab Storeys Storeys
construction, is supported on the column, mm m mm mm m
and slab adequately bears on stiffening (1) (2) (3) (4) (5) (6)
walls. This construction will provide 0 100 3.2 100 — 4.5
lateral support to the column, in the @ 200 3.2 100 200 6.0
direction of both horizontal axes. iii) 300 3.4 100 2W 8.0
iv) Above300 5.0 100 2(X) 8.0
4.2.2 Stability
A wall or column subject to vertical and lateral loads 1)sto~y height and maximumspacingsas given are Centre-tO_
centredimensions.
may be considered to be provided with adequate lateral

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 11


. ,. , 4.2.2.5 Capacity of a cross wall, also called shear wall,
d’..”.,?’
,. . . . .
sometimes to take horizontal loads and consequently
I STIFFENING
WALL
15
bending moments increases, when parts of bearing
walls act as flanges to the cross wall. Maximum
overhanging length of bearing wall which could
effectively function as a flange should be taken as 12 t
or H16, whichever is less in case of TII shaped walls,
and 6 tor H/l 6, whichever is less in case of LIU shaped
OPENING OPENING
walls, where t is the thickness of bearing wall and H is
the total height of wall above the level being
considered, as shown in Fig. 10.

4.2.2.6 External walls of basement and plinth


,.,. .,
In case of external walls of basement and plinth,
VA
stability requirements of 4.2.2 maybe deemed to have
FIG. 8 OPENING IN STIFFENING WALL been met with, if

a) bricks used in basement and plinth have a


cross walls are built jointly with the bearing
minimum crushing strength of 5 N/mm* and
walls and are jointly mortared, or the two
mortar used in masonry is of Grade M 1 or
interconnected by toothing. Alternatively,
better;
cross walls may be anchored to walls to be
supported by ties of non-corrodible metal of b) clear height of ceiling in basement does not
minimum section 6 mm x 35 mm and length exceed 2.6 m;
600 mm with ends bend at least 50 mm; c) walls are stiffened according to provisions
maximum vertical spacing of ties being 1.2 m of 4.2.2.1;
(see Fig. 9). d) in the zone of action of soil pressure on
basement walls, traffic load excluding any
surcharge due to adjoining buildings does not
exceed 5 kN/m2 and terrain does not rise; and
e) minimum thickness of basement walls is in
accordance with Table 3.
NOTE — In case there is surcharge on basement walls
from adjoining buildings, thickness of basement walls
shall be based on structural analysis.

Table 3 Minimum Thickness of Basement Walls


[Clause 4.2.2.6(e)]

sl Height of the Groand Above Minimom


No. Basement Floor Level Nominal
.- A -. TMcknesa
Wall loading Wall loading of
(permanent load) (permanent load) Basement
FIG. 9 ANCHORING OF STIFFENING WALL WITH less than 50 kN/m more than 50 kN/m
SUPPORT WALL (1) (2) (3) (4)

4.2.2.3 In case of halls exceeding 8.0 m in length, O Up to 1.4m t$$tol.75m 300 mm


safety and adequacy of lateral supp:$mts shall always @ Upto2m Up to 2.5 m 400 mm
be checked by structural analysis.
4.2.2.7 Walls mainly subjected to lateral loads
4.2.2.4 A trussed roofing may not provide lateral
support unless special measures are adopted to brace a) Free standing wall — A free standing wall
and anchor the roofing. However, in case of residential such as compound wall or parapet wall is
and similar buildings of conventional design with acted upon by wind force which tends to
trussed roofing having cross walls, it maybe assumed overturn it. This tendency to over-turning is
that stability requirements are met with by the cross resisted by gravity force due to self-weight
walls and structural analysis for stability may be of wall, and also by flexural moment of
dispensed with. resistance on account of tensile strength of

12 NATIONAL BUILDING CODE OF INDIA


I
t ////// ‘//d

I b! EFFECTIVE OVERHANGING WIDTH


OF FLANGE= 12 t OR H/6 WHICHEVER
IS LESS, H BEING THE TOTAL HEIGHT
OF WALL ABOVE THE LEVEL BEING
CONSIDERED
T
I I

‘EFFECTIVE OVERHANGING
WIDTH OF FLANGE, BOTH SIDES

EFFECTIVE OVERHANGING WIDTH


OF FLANGE= 6 t OR H/16 WHICHEVER
IS LESS, H BEING THE TOTAL HEIGHT
OF WALL ABOVE THE LEVEL BEING
CONSIDERED

> EFFECTIVE OVERHANGING


WIDTH OF FLANGE

FIG. 10 TYPICAL DETAILS FOR ANCHORAGE OF SOLID WALLS

masonry. Free standing walls shall thus be 4.3 Effective Height


designed as in 5.5.2.1. If mortar used for
4.3.1 Wall
masonry cannot be relied upon for taking
flexural tension (see 5.4.2), stability of free Effective height of a wall shall be taken as shown in
standing wall shall be ensured such that Table 4 (see Fig. 11).
stability moment ‘bf wall due to self-weight NOTE— A roof truss or beamsupportedon a columnmeeting
equals or exceeds 1.5 times the overturning the requirementsof 4.2.2.1is deemedto providelateral support
moment. to the column only in tbe direction of the beanrhrnss.
b) Retaining wall — Stability for retaining walls 4.3.2 Column
shall normally be achieved through gravity
action but flexnral moment of resistance could In case of a column, effective height shall be taken as
also be taken advantage of under special actual height for the direction it is laterally supported
circumstances at the discretion of the designer and twice the actual height for the direction it is not
(see 5.4.2). laterally supported (see Fig. 12).

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 13


Table 4 Effective Height of Walls
(Clause 4.3.1)

S1No. Condition of Support Effective Height


(1) (2) (3)

i) Lateral as well as rotational restraint (that is, full restraint) at top and bottom. For example, when the floor/roof 0.75 H
spans on the W~lS so that reaction to load of floorlroof is provided hy the walls, or when an RCC fl~rlmof
has bearing on the wall (minimum 9 cm), irrespective of the direction of the span foundation footings of a wall
give lateral as well as rotational restraint
ii) Lateral as well as rotational restraint (that is, full restraint) at one end and ordy lateral restraint (that is, partial 0.85 H
restraint) at the other. For example, RCC floor/roof at one end spannrng or adequately bearing on the wall and
timber floorhoof not spanning on watl, but adequately anchored to it, on the other end
iii) Lateral restraint, without rotational restraint (that is, partial restraint) on both endsFor example, timber floorhoof, 1.00H
not spanning on the wall but adequately anchored to it on both ends of tie wall, that is, top and bottom
iv) Lateral restraint as well as rotational restraint (that is, full restraint) at bottom but have no restraint at the top. 1.50H
For example, parapet walls with RCC roof having adequate bearing on the lower wall, or a compound wall
with proper foundation on the soil.

NOTES
1 His the height of wall between centres of support in case of RCC slabs and timber floors. In case of footings or foundation block,
height (H) is measured from top of footing or foundation block. In case of roof truss, height (H) is measured up to bottom of the tie
beam. In case of beam and slab construction, height should be measured from centre of bottom slab to centre of top beam. All these
cases are illustrated by means of examples shown in Fig. 11.
2 For working out effective height, it is assumed that concrete DPC, when properly bonded with masonry, does not cause
..
discontinuity in the wall.
3 Where memberane type damp-proof course or termite shield causes a discontinuity in bond, the effective height of wall maybe
taken to be greater of the two values calculated as follows:
a) consider H from top of footing ignoring DFC and take effective height as 0.75 H.
b) consider H from top of DPC and take effective height as 0.85 H.
4 When assessing effective height of walls, floors not adequately anchored to walls shall not be considered as providing lateral
SUppOrt tO such Walk.

5 When thickness of a wall bonded to a pier is at least two-thirds of the thickness of the pier measured in the same direction,the wall
and pier may be deemed to act as one stmctural element.

11 A RCC FLOOfWtOOF BEING 11 B TIMBER FLOOFUROOF 11 C TIMBER FLOORAND 11 D FREE STANDINGWALL


ON WALLIRRESPECTIVE TRUSSED ROOF
OF DIRECTION OF SPAN

FIG. 11 EFFECTIVE HEIGHT OF WALL

14 NATIONAL BUILDING CODE OF INDIA


Y
..
Y

x
x -J — ‘----+--x

I f

x x

EFFECTIVE HEIGHT EFFECTIVE HEIGHT


ABOUT AXIS 12A ABOUT AXIS
X- X=l.OH X- X=2.OH
Y- Y=l.OH Y- Y=l.OH

THE BEAM
\ ONLY x x

L STIFFENING WAL.L

12 B 12C

Roof Construction Effective Height About Axis Effective Height About Axis
Fig. 12B Fig. 12C
With precast concrete units X–X=l.0H2 X–X=l.5HZ
of in-situ concrete floor or Y– Y= l.OH1 Y–Y=l.OH1
roof Y–Y= 1.5H1
(No ties)

With light deck or similar X–X= l.OHL x–x=2.0H~


roof Y–Y=l.OH1 Y–Y=l.OH1
Y–Y=2.0H1
(No ties)

FIG. 12 EXAMPLE OF EFFECTIVE HEIGHT OF COLUMNS

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 15

..
A
NOTES 0.5 H and it is equal to 2 H when height
1 A roof truss or beam supported on a column meeting the of any opening exceeds 0.5 H, and
requirements of 4.2.2.1 is deemed to provide lateral support to
the column only in the direction of the bearnhruss. 2) Effective height for the direction parallel
2 When floor or roof consisting of RCC beams and slabs is to the plane of the wall equals 2 H.
supported on columns, tbe columns would be deemed to be
laterally supported in both directions. 4.4 Effective Length
4.3.3 Openings in Walls Effective length of a wall shall be as given in Table 5.
When openings occur in a wall such that masonry
4.5 Effective Thickness
between the openings is by definition a column,
effective height of masonry between the openings shall Effective thickness to be used for calculating
be reckoned as follows: slenderness ratio of a wall or column shall be obtained
a) When wall has full restraint at the top: as in 4.5.1 to 4.5.5.
1) Effective height for the direction 4.5.1 For solid walls, faced walls or columns, effective
perpendicular to plane of wall equals thickness shall be the actual thickness.
0.75 H plus 0.25 HI, where H is the
distance between supports and H, is the 4.5.2 For solid walls adequately bonded into piers,
height of the taller opening; and buttresses, effective thickness for determining
2) Effective height for the direction parallel slenderness ratio based on effective height shall be the
to the wall equals H, that is, the distance actual thickness of wall multiplied by stiffening
between the supports. coefficient as given in Table 6. No modification in
effective thickness, however, shall be made when
b) When wall has partial restraint at the top and
bottom: slenderness ratio is to be based on effective length of
walls.
1) Effective height for the direction
perpendicular to plane of wall equals H 4.5.3 For solid walls or faced walls stiffened by cross
when height of neither opening exceeds walls, appropriate stiffening coefficient may be

Table 5 Effective Length of Walls


(Clause 4.4)

S1 No. Conditions of Support (See Fig. 13) Effective Length


(1) (2) (3)

i) Where a wait is continuous and is supported by cross wall and there is no opening within a distance of H/8 0.8 L
from the face of cross watl (see Fig. 13)
or
where a wait is continuous and is supported by piershrttresses conforming to LL2.12@)
ii) where a wall is suppotted by a cross watt at one end and continuous with cross watl at other end 0.9 L
or
Where a wafl is supported by a pierhrttress at one end and continuous with pierhtttress at other end
conforming to 4.2.l.3(b)
iii) Where a watt is supported at each end by cross wall 1.OL
or
Where a wall is supported at each end by a pierhrttress conforming to 4.2.l.2(b)
iv) Where a waif is ftee at one end and contiguous with a pierhrttress at the other end ;. 1.5L
or
where a wait is free at one end and continuous with a piedhtress at the other end conforming
to 4.2.l.2(tr)
v) Where a watl is free at one end and supported at the other end by a cross watl 2.0 L
or
Where a watl is free at one end and supported at the other end by a pierhrttress conforming to 4.2.12@)

where
L = Length of wall tlom or between cenfres of cross wafl, piers or buttress and
H = Actuaf height of wall between centtes of adequate taterat support.

NOTE — In case there is an opening tafler than 0.5 H in a wall, ends of the wall at the opening shatl be considered as free. Cross
wafls shrdl conform to 4.2.2.l(d).

16 NATIONAL BUILDING CODE OF INDIA


L tw
1-’= Wall is continuous at both ends and is
supportad by cross walls of thickness
% fw/2 or 100 mm whlchavar k more,
length of oroaa wall is not lass than
H/6,0paning in wall is not leas than
x 2 H18, y? H16 M8 from cross wall
1=0.6L
13A CASE 1
L
I

Same as case 1 except that one end


h of the well is dieoontinuous

1=0.9L
13B CASE2

Same as case 1 except that wall


A is discontinuous on both ends

x 2 H16, y 2 H16
/= L 13C CASE3
L

One end of the wall is free, other is


FREE supportadby acroaawailandis
w
END continucwa. Thara being rro opening
.—
within H/8 ~ cross wall.
%
-l=i.57 13D CASE4

t-%

7 x Same es oaaa 4 but op6n@ is within


A H/8 from cross wall and thus that
end is taken as diaqmtinuous
.-
x < &i/q y ~ H/6
I=2L
13E CASE5

/=l,5&i
13F CASE6

l-%
I I

Wall length is between two opaning M&h


are doaar than H18from _ walls

13G CASE7

FIG. 13 EFFECTIVE LENGTH OF WALL

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 17


r--

determined from Table 6 on the assumption that the 4.6.2 Columns


cross walls are equivalent to piers of width equal to
For a column, slenderness ratio shall be taken to be
the thickness of the cross wall and of thickness equal
the greater of the ratios of effective heights to the
to three times the thickness of stiffened wall.
respective effective thickness, in the two principal
Table 6 Stiffening Coefficient for Walls directions. Slenderness ratio for a load bearing column
Stiffened by Piers, Buttresses or Cross Walls shall not exceed 12.
(Clauses 4.5.2 and 4.5.3) 4.7 Eccentricity
S1 s Stiffening Coefficient Eccentricity of vertical loading at a particular junction
No. Ratio Q / A T
Wp in a masonry wall shall depend on factors, such as
tp tp .t
—= 1 —= 2 2 = 3 or more extent of beting, magnitude of loads, stiffness of slab
tw tw tw or beam, fixity at the support and constructional details
(1) (2) (3) (4) (5)
at junctions. No exact calculations are possible to make
i) 6 1.0 1.4 2.0 accurate assessment of eccentricity. Extent of
ii) 8 1.0 1.3 1.7
iii) 10 1.0 1.4 eccentricity under any particular circumstances has,
iv) 15 1.0 }:: 1.2 therefore, to be decided according to the best
v) 20 or more 1.0 1.0 1.0
judgement of the designer. Some guidelines for
where
assessment of eccentricity are given in Annex A.
Sp = Centre-to-centre spacing of the pier or cross wall,
tP = Thickness of pier as defined in 2.3.2 (see Fig. 1), 5 STRUCTURAL DESIGN
tw= Actual thickness of the wall proper (see Fig. 1), and
WP= Width of the pier in the direction of the wall or the actual 5.1 General
thickness of the cross wall. The building as a whole shall be analyzed by accepted
NOTE — Linear interpolation between the vrdues given in this
principles of mechanics to ensure safe and proper
table is permissible but not extrapolation outside the limits given.
functioning in service of its component parts in relation
4.5.4 For cavity walls with both leaves of uniform to the whole building. All component parts of the
thickness throughout, effective thickness shall be taken structure shall be capable of sustaining the most adverse
as two-thirds of the sum of the actual thickness of the combinations of loads, which the building may be
two leaves. reasonably expected to be subjected to during and after
construction.
4.5.5 For cavity walls with one or both leaves
adequately bonded into piers, buttresses or cross walls 5.2 Design Loads
at intervals, the effective thickness of the cavity wall Loads to be taken into consideration for designing
shall be two-thirds of the sum of the effective thickness masonry components of a structure are:
of each of the two leaves; the effective thickness of each
a) dead loads of walls, columns, floors and roofs;
leaf being calculated using 4.5.1 or 4.5.2 as appropriate.
b) live loads of floors and roofi
4.6 Slenderness Ratio
c) wind loads on walls and sloping roofi and
4.6.1 Walls d) seismic forces.
For a wall, slenderness ratio shall be effective height NOTE — When a buildlng is subjected to other loads,
such as vibration from railways; machinery, etc, these
divided by effective thickness or effective length
should be taken into consideration accordingly to the
divided by the effective thickness, whichever is less. best judgement of the designer (see also Part 6 ‘Structural
In case of a load bearing wall, slenderness ratio shall Design, Section 1 Loads, Forces and Effects’).
not exceed that given in Table 7.
5.2.1 The design loads an# other forces to be taken for
Table 7 Maximum Slenderness Ratio for a tie design of masonry structures shall 6conform to Part
Load Bearing Wall ‘StructuralDesign, Section 1 Loads, Forces and Effects’.
(Clause 4.6.1) NOTE— Duringconstruction,suitablemeasuresshallbe taken
to ensurethat masonryis not liable to damageor failure due to
Number of Maximum SlendermesaRatio action of wind forces, back filling behind walls or temporary
Storeys F A Y construction loads.
Using Portland Cement or Using Lime
Portland Pozzolana Cement Mortar
5.3 Load Dispersion
in Mortar
(1) (2) (3) 5.3.1 General
Not exceeding 2 27 20
The angle of dispersion of vertical load on walls shall
Exceeding 2 27 13 be taken as not more than 30° from the vertical.

18 NATIONALBU~DING CODE OF INDIA


5.3.2 Arching Action to 5.4.1.3. Values of basic compressive stress given in
Table 8 take into consideration crushing strength of
Account may also be taken of the arching action of
masonry unit and grades of mortar and hold good for
well-bonded masonry walls supported on lintels and
values of slenderness ratio not exceeding 6, zero
beams, in accordance with established practice.
eccentricity and masonry unit having height to width
Increased axial stresses in the masonry associated with
ratio (as laid) equal to 0.75 or less.
arching action in this way, shall not exceed the
permissible stresses given in 5.4. Alternatively, basic compressive stress may be based
on results of prism test given in Annex B on masonry
5.3.3 Lintels
made from masonry units and mortar to be actually
Lintels that support masonry construction shall be used in a particular job.
designed to carry loads from masonry (allowing for
arching and dispersion), where applicable and loads 5.4.1.1 Stress reduction factor
received from any other part of the structure. Length This factor, as given in Table 9, takes into consideration
of bearing of lintel at each end shall not be less than the slenderness ratio of the element and also the
90 mm or one-tenth of the span, whichever is more eccentricity of loading.
and area of the bearing shall be sufficient to ensure
that stresses in the masonry (combination of wall 5.4.1.2 Area reduction factor
stresses, stresses due to arching action and bearing This factor takes into consideration smallness of the
stresses from the lintel) do not exceed the stresses sectional area of the element and is applicable when
permitted in 5.4 (see Annex C). sectional area of the element is less than 0.2 m2.
5.4 Permissible Stresses The factor k,= 0.7 + 1.5A, A being the area of section
in m2.
5.4.1 Permissible Compressive Stress
5.4.1.3 Shape modification factor
Permissible compressive stress in masonry shall be
based on value of basic compressive stress (&) as given This factor takes into consideration the shape of the
in Table 8 and multiplying this value by factors known unit, that is, height to width ratio (as laid) and is given
as stress reduction factor (k,), area reduction factor (k,) in Table 10. This factor is applicable for units for
and shape modification factor (kP) as detailed in 5.4.1.1 crushing strength up to 15 N/mm2. .
*
Table 8 Basic Compressive Stresses for Masonry (After 28 days)
(Clauses 5.4.1 and 6.3.1)

S1 Mortar Basic Compressive Stresses in N/mm* Corresponding to Masonry Units of which Height to Width
No. Type Ratio does not Exceed 0.75 and Crushing Strength, in N/mm2, is not Less than
(Ref Table 1) -
-~ -
3.5 5.0 7.5 10 12.5 15 17.5 20 25 30 35 40

(}) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14)

i) HI 0.35 0.50 0.75 1.00 1.16 1.31 1.45 1.59 1.91 2.21 2.5 3.05
ii) H2 0.35 0.50 0.74 0.96 1.09 1.19 1.30 1.41 1.62 1.85 2.1 2.5
iii) Ml 0.35 0.50 0.74 0.96 1.06 1.13 1.20 1.27 1.47 1.69 1.9 2.2
iv) M2 0.35 0.44 0.59 0.81 0.94 1.03 1.10 1.17 1.34 1.51 1.65 1.9
v) M3 0.25 0.41 0.56 0.75 0.87 0.95 1.02 1.10 1.25 1.41 1.55 1.78
vi) L1 0.25 0.36 0.53 0.67 0.76 0.83 0.90 0.97 1.11 1.26 1.4 1.06
vii) L2 0.25 0.31 0.42 0.53 0.58 0.61 0.65 0.69 0.73 0.78 0.85 0.95

NOTES
1 The table is valid for slenderness ratio up to 6 and loading with zero eccentricity.
2 The values given for basic compressive stress are applicable only when the masonry is properly cured.
3 Linear interpolation is permissible for units having crushing strengths between those given in the table.
4 The permissible stress for random rubble masonry may be taken as 75 percent of the eorrespcmding stress for coarsed walling of
similar materials,
5 The strength of ashlar masonry (natural stone masonry of massive type with thin joints) is closely related to intrinsic strength of the
stone and allowable working stress in excess of those given in the table may be allowed for such masonry at the discretion of the
designer.
6 For calculation of basic compressive stress of stabilized mud block having thickness 100 mm or more, reference to specialist
literature may be made.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 19


w. . ,.., . . .. .. ?a!aM @*!mmmmwwmwAmaw .. —,... —,----- —. . . .. . .. . . . .— -—--- . . . . . .-.. ” . . . . . .

*&’
‘--~-

Table 9 Stress Reduction Factor for Slenderness Ratio and Eccentricity


(Ckmse 5.4.1.1)

Slenderness Eccentricity of Loading Divided by the Thickness of the Member


Ratio - ,,
/
o 1/24 1/12 1/6 1/4 1/3

(1) (2) (3) (4) (5) (6) (7)

6 1.00 1.00 1.00 1.00 1.00 1.00


8 0.95 ().95 0.94 0.93 (k92 0.91
10 0.89 ().88 0.87 0.85 0.83 0.81
12 0.84 ().83 0.81 0.78 0.75 0.72
14 0.78 ().76 0.74 0.70 0.66 0.66
16 0.73 ().7 1 0.68 0.63 0.58 0.53
18 0.67 0.64 0.61 0.55 0.49 0.43
>
20 0.62 0.59 0.55 0.48 0.41 0.34
22 0.56 0.52 0.48 0.40 0.32 0.24
24 0.51 0.47 0.42 0.33 0.24 —
26 0.45 0.40 0.35 0.25 — —
27 0.43 0.38 0.33 0.22 — —

NOTES
1 Linear interpolation between values is permitted.
2 Where in special cases the eccentricity y of loading lies between 1/3 and 1/2 of the thickness of the member, the stress reduction
factor should vary linearly between unity and 0.20 for slenderness ratio of 6 and 20 respectively.
3 Slenderness ratio of a member for sections within 1/8 of the height of the member above or below a lateral support may be taken to
be 6.

Table 10 Shape Modification Factor tension shall be disregarded for computing the
for Masonry Units load carrying capacity of the member.
(Clause 5.4.1.3) NOTE — When resultant eccentricity ratio of loading is
4.
1/24 or less, compressive stress due to bending shall be
Height to Shape Modification Factor (kP) for Units ignored and only axial stress need be computed for the
Width Ratio Having Crushing Strength in N/mm2 is purpose of design.
of Units ~~
(as Laid) S.. 5.4.1.5 Increase in permissible compressive stress for
7.5 10.0 15.0
(1)
walls subjected to concentrated loads
(2) (3) (4) (5)

up to 0.75 1.0 1.0 1.0 1.0 When a wall is subjected to a concentrated load (a load
1.0 1.2 1.1 1.1 1.0 being taken to be concentrated when area of supporting
1.5 1.5 1.3 1.2 1.1 wall equals or exceeds three times the bearing area),
2.0 to 4.0 1.8 1.5 1.3 1.2 certain increase in permissible compressive stress may
NOTE — Linear interpolation between values is permissible. be allowed because of dispersal of the load. Since,
according to the present state of art, there is diversity
5.4.1.4 Increase in permissible compressive stresses of views in regard to manner and extent of dispersal,
allowed for eccentric vertical loads, laterul loads under design of walls subjected to concentrated loads may,
certain conditions therefore, be worked out as per the best judgement of
the designer. Some guidelines in this regard are given
In members subjected to eccentric and/or lateral loads,
in Annex C.
increase in permissible compressive stress is allowed
as follows: 5.4.2 Permissible Tensile Stress
a) When resultant eccentricity ratio exceeds As a general rule, design of masonry shall be based on
1/24 but does not exceed 1/6, 25 percent the assumption that masonry is not capable of taking
increase in permissible compressive stress is any tension. However, in case of lateral loads normal
allowed in design. to the plane of wall, which causes flexural tensile stress,
b) When resultant eccentricity ratio exceeds as for example, panel, curtain partition and free
1/6, 25 percent increase in permissible stress standing walls, flexural tensile stresses as follows may
is allowed but the area of the section under be permitted in the design for masonry:

20 NATIONAL BUILDING CODE OF INDIA


F-

Grade Mlor – 0.07 N/mmz for bending in walls and section in case of columns in relation to
better mortar the vertical direction where strength of masonry units and grade of mortar to be
tension developed is normal used, taking into consideration various factors, such
to bed joints. as slenderness ratio, eccentricity y, area of section,
— 0,14 N/mmz for bending in workmanship, quality of supervision, etc, subject
the longitudinal direction further to provisions of 5.5.1.1 to 5.5.1.4.
where tension developed
5.5.1.1 Solid walls
is parallel to bed joints,
provided crushing strength Thickness used for design calculation shall be the actual
of masonry units is not less thickness of masonry computed as the sum of the
than 10 N/mm2. average dimensions of the masonry units specified in
Grade M2 mortar – 0.05 N/mm2 for bending in the relevant stdndard, together with the specified joint
the vertical direction where thickness. In masonry with raked joints, thickness shall
tension developed is normal be reduced by the depth of raking, of joints for
to bed joints. plastering/pointing.
— 0.10 N/mm* for bending in 5.5.1.2 Cavity walls
the longitudinal direction
a) Thickness of each leaf of a cavity wall shall
where tension developed
not be less than 75 mm.
is parallel to bed joints,
provided crushing strength b) Where the outer leaf is half masonry unit in
of masonry units is not less thickness, the uninterrupted height and length
than 7.5 N/mm*. of this leaf shall be limited so as to avoid
undue loosening of ties due to differential
NOTES
movements between the two leaves. The outer
1 No tensile stress is permitted in masonry in case of water-
retaining structures in view of water in contact with masonry. leaf shall, therefore, be supported at least at
Also no tensile stress is permitted in earth-retaining every third storey or at every 10 m of height
structures, in view of the possibility of presence of water at whichever is less, and at every 10 m or less
the back of such walls.
along the length.
2 Allowable tensile stress in bending in the vertical direction
may be increased to 0.1 N/mm2 for M 1 mortar arrd 0.07 N/mm2 c) Where the load is carried by both leaves of a
for M2 mortar in case of boundry walls/compound at the wall of a cavity construction, the permissible
discretion of the designer, since there is not much risk to life stress shall be based on the slenderness ratio
and property in the event of failure of such walls. derived from the effective thickness of
the wall as given in 4.5.4 or 4.5.5. The
5.4.3 Permissible Shear Stress
eccentricity of the load shall be considered
In case of walls built in mortar not leaner than Grade with respect to the centre of gravity of the
Ml (see Table 1) and resisting horizontal forces in the cross-section of the wall.
plane of the wall, permissible shear stress calculated d) Where the load is carried by one leaf only,
on the area of bed joints, shall not exceed the value the permissible stress shall be the greater of
obtained by the formula given below, subject to a values calculated by the following two
maximum of 0.5 N/mm*: alternative methods:

& = 0.1 +fJf5 1) The slenderness ratio is based on the


effective thickness of the cavity wall as
Compressive stress due to dead loads in
a whole as given in 4.5.4 or 4.5.5 and on
N/mm*, and the eccentricity of the load with respect
Permissible shear stress in N/mm*. to the centre of gravity of the cross-
5.4.4 If there is tension in any part of a section of section of the whole wall (both leaves).
masonry, the area under tension shall be ignored while (This is the same method as where the
working out shear stress on the section. load is carried by both the leaves but the
eccentricity will be more when the load
5.5 Design Thickness/Cross-Section is carried by one leaf only.)
2) The slenderness ratio is based on the
5.5.1 Walls and Columns Subjected to Vertical Loads
effective thickness of the loaded leaf only
Walls and columns bearing vertical loads shall be using 4.5.1 and 4.5.2, and the eccentricity
designed on the basis of permissible compressive stress. of the load will also be with respect to the
Design consists in determining thickness in case of centre of gravity of the loaded leaf only.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 21


.
,-.‘) -\
~ .+
_.

In either alternative, only the actual thickness of the Table 11 Height to Thickness Ratio of Free
load bearing leaf shall be used in arriving at the cross- Standing Walls Related to Wind Speed
sectional area resisting the load (see 5.5.1.1). (Clause 5.5.2.1)

5.5.1.3 Faced wall Design Wind Pressure Height to Thickness Ratio


Nhnm2
The permissible load per length of wall shall be taken (1) (2)
as the product of the total thickness of the wall and the
Up to 285 10
permissible stress in the weaker of the two materials.
575 7
The permissible stress shall be found by using the total 860 5
thickness of the wall when calculating the slenderness 1150 4
ratio.
NOTES *&
5.5.1.4 Veneered wall 1 For intermediate values, linear interpolation is permissible.
2 Height is to be reckoned from 150 mm below ground level
The facing (veneer) shall be entirely ignored in or top of footing/foundation block, whichever is higher, and
calculations of strength and stability. For the purpose up to the top edge of the wall.
of determining the permissible stress in the backing, 3 The thickness should be measured including the thickness
of the plaster.
the slenderness ratio shall be based on the thickness of
the backing alone.
5.5.3 Walls and Columns Subjected to Vertical as well
5.5.2 Walls and Columns Mainly Subjected to Lateral as Lateral Loads
Loads For walls and columns, stress worked out separately
5.5.2.1 Free standing walls for vertical loads as in 5.5.1 and lateral loads as in 5.5.2
shall be combined and elements designed on the basis
a) Free standing walls, subjected to wind of permissible stress,
pressure or seismic forces shall be designed
5.5.4 Walls Subjected to In-Plane Bending and
on the basis of permissible tensile stress in
Vertical Loads (Shear Walls)
masonry or stability as in 4.2.2.4. However,
in seismic Zones II, free-standing wails may Walls subjected to in-plane bending and vertical loads,
be apportioned without making any design that is, shear walls shall be designed on the basis of no
calculations with the help of Table 11 tension with permissible shear stress and permissible
provided the mortar used is of grade not leaner compressive stress. .
than Ml.
5.5.5 Non-Load Bearing Walls
b) If there is a horizontal damp-proof course near
Non-load bearing walls, such as panel walls, curtain
the base of the wall, that is, not capable of
walls and partition walls which are mainly subjected to
developing tension vertically, the minimum
lateral loads, according to present state of art, are not
wall thickness should be the greater of that
capable of precise design and only approximate methods
calculated from either:
based on some tests are available. Guidelines for
1) the appropriate height to thickness ratio approximate design of these walls are given in Annex D.
given in Table 11 reduced by 25 percent,
reckoning the height from the level of the 6 GENERAL REQUIREMENTS
damp-proof course; or
6.1 Methods of Construction
2) the appropriate height to thickness ratio
given in Table 11 reckoning the height 6.1.1 General
from the lower level at which the wall is Construction of the following types of load bearing
restrained laterally. and non-load bearing masonry walls shall be carried
out in accordance with good practice [6-4(3)].
5.5.2.2 Retaining walls
a) Brickwork,
Normally masonry of retaining walls shall be designed
b) Stone masonry,
on the basis of zero-tension, and permissible
compressive stress. However, in case of retaining walls c) Hollow concrete block masonry,
for supporting horizontal thrust from dry materials, d) Gypsum partition blocks,
retaining walls may be designed on the basis of e) Autoclave cellular concrete block masonry,
permissible tensile stress at the discretion of the and
designers. 0 Lightweight concrete block masonry.

22 NATIONAL BUILDING CODE OF INDIA


6.1.2 Construction of Buildings in Seismic Zones b) Deviation in verticality in total height of any
wall of a building more than one storey in
No special provisions on construction are necessary
height shall not exceed 12.5 mm.
for buildings constructed in Zones II. Special features
c) Deviation from position shown on plan of any
of construction for earthquake resistant masonry
brickwork shall not exceed 12.5 mm.
buildings in Zones III, IV and V shall be applicable
according to good practice [6-4(3)]. d) Relative displacement between load bearing
walls in adjacent storeys intended to be in
6.2 Minimum Thickness of Walls from Consideration vertical alignment shall not exceed 6 mm.
other than Structural e) Deviation of bed-joint from horizontal in a
Thickness of walls determined from consideration of length of 12 m shall not exceed 6 mm subject
strength and stability may not always be adequate in to a maximum deviation of 12 mm.
respect of other requirements, such as resistance to f) Deviation from the specified thickness of bed
fire, thermal insulation, sound insulation and joints, cross-joints and perpends shall not
resistance to damp penetration for which reference exceed one-fifth of the specified thickness.
may be made to the appropriate Parts/Sections of the NOTE — These tolerances have been specified from
Code, and thickness suitably increased, where found the point of view of their effect on the strength of
necessary. masonry. The permissible stress recommended in 5.3
may be considered applicable only if these tolerances
are adhered to.
6.3 Workmanship

6.3.1 General 6.4 Joints to Control Deformation and Cracking

Workmanship has considerable effect on strength of Special provision shall be made to control or isolate
masonry and bad workmanship may reduce the strength thermal and other movements so that damage to the
of brick masonry to as low as half the intended strength. fabric of the building is avoided and its structural
The basic compressive stress values for masonry as sufficiency preserved. Design and installation of
given in Table 8 would hold good for commercially joints shall be done according to the appropriate
obtainable standards of workmanship with reasonable recommendations in accordance with good practice
degree of supervision. If the work is inadequately [6-4(5)].
supervised, strength should be reduced to three-fourth
6.5 Chases, Recesses and Holes
or less at the discretion of the designer.
6.5.1 Chases, recesses and holes are permissible in
6.3.2 Bedding of Masoniy Units
masonry only if these do not impair strength and
Masonry units shall be laid on a full bed of mortar stability of the structure.
with frog, if any, upward such that cross-joints and
6.5.2 In masonry, designed by structural analysis, all
wall joints are completely filled with mortar. Masonry
chases, recesses and holes shall be considered in
units which are moved after initial placement shall
structural design and detailed in building plans.
be relaid in fresh mortar, discarding the disturbed
mortar. 6.5.3 When chases, recesses and holes have not been
considered in structural design and are not shown in
6.3.3 Bond
drawings, these may be provided, subject to the
Cross-joints in any course of one brick thick masonry constraints and precautions specified in 6.5.3.1
wall shall be not less than one-fourth of a masonry to 6.5.3.10.
unit in horizontal direction from the cross-joints in the
6.5.3.1 As far as possibk, services should be planned
course below. In masonry walls more than one brick
with the help of vertical chases and use of horizontal
in thickness, bonding through the thickness of wall
chases should be avoided.
shall be provided by either header units or by other
equivalent means in accordance with good practice 6.5.3.2 For load bearing walls, depth of vertical and
[6-4(4)]. horizontal chases shall not exceed one-third and one-
sixth of the wall thickness respectively.
6.3.4 Verticality and Alignment
6.5.3.3 Vertical chases shall not be closer than 2 m in
All masonry shall be built true and plumb within the
any stretch of wall and shall not be located within
tolerances prescribed below; care shall be taken to keep
345 mm of an opening or within 230 mm of a cross
the perpends properly aligned:
wall that serves as a stiffening wall for stability. Width
a) Deviation from vertical within a storey shall of a vertical chase shall not exceed thickness of wall
not exceed 6 mm per 3 m height. in which it occurs.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 23


6.5.3.4 When unavoidable horizontal chases of width 6.6.2 The load per unit length on a corbel shall not
not exceeding 60 mm in a wall having slenderness be greater than half of the load per unit length on the
ratio not exceeding 15 may be provided. These shall wall above the corbel. The load on the wall above
be located in the upper or lower middle third height the corbel, together with four times the load on the
of wall at a distance not less than 600 mm from a corbel, shall not cause the average stress in the
lateral support. No horizontal chase shall exceed supporting wall or leaf to exceed the permissible
1 m in length and there shall not be more than stresses given in 5.4.
2 chases in any one wall. Horizontal chases shall have
6.6.3 It is preferable to adopt header courses in the
minimum mutual separation distance of 500 mm. Sum
corbelled portion of masonry from considerations of
of lengths of all chases and recesses in any horizontal
economy and stability.
plane shall not exceed one-fourth the length of the
wall. 7 SPECIAL CONSIDERATION IN
EARTHQUAKE ZONES
6.5.3.5 Holes for supporting put-logs of scaffolding
shall be kept away from bearings of beams, lintels, 7.0 Special features of design and construction for
and other concentrated loads. If unavoidable, stresses earthquake resistant masonry buildings are given in 7.2
in the affected area shall be checked to ensure that these to 7.8.2. Reference may also be made to good practice
are within safe limits. [6-4(6)] for detailed information.

6.5.3.6 No chase, recess or hole shall be provided in 7.1 Categories of Buildings


any stretch of a masonry wall, the length of which is
For the purpose of specifying the earthquake resistant
less than four times the thickness of wall, except when ---
features in masonry and wooden buildings, the
found safe by structural analysis.
buildings have been categorized in five categories A
6.5.3.7 Masonry directly above a recess or a hole, if to E based on the seismic zone and the importance of
wider than 300 mm, shall be supported on a lintel. No building I,
lintel, however, is necessary in case of a circular recess where
or hole exceeding 300 mm in diameter provided upper
half of the recess or hole is buik as a semi-circular I = Importance factor applicable to the building
arch of adequate thickness and there is a adequate (see Table 35 of Part 6, Section 1)
length of masonry on the sides of openings to resist 7.1.1 The building categories are given in Table 12.
the horizontal thrust.
Table 12 Building Categories for Earthquake
6.5.3.8 As far as possible chases, recesses and holes
Resisting Features
in masonry should be left (inserting sleeves, where
(Clauses 7.1.1 and 8.1.2)
necessary) at the time of construction of masonry so
as to obviate subsequent cutting. If cutting is Importance Factor Sekmlk zone
unavoidable, it should be done without damage to the F A
*
surrounding or residual masonry. It is desirable to use II m IV v
such tools for cutting which depend upon rotary and (1) (2) (3) (4) (5)
not on heavy impact for cutting action. 1.0 A B c D

6.5.3.9 No chase, recess or hole shall be provided in 1.5 B c D E

half-brick load bearing wall, excepting the minimum


number of holes needed for scaffolding. 7.2 Masonry Units

6.5.3.10 Chases, recesses or holes shall not be cut into Bricks/Blocks as per the accepted standards [6-4(1)]
walls made of hollow or perforated units, after the units having a crushing strength not less than 3.5 MPa shall
have been incorporated in masonry. be used. However, higher strength of masonry units
may be required depending upon number of storeys
6.6 Corbeling and thickness of walls in accordance with provisions
of this Section.
6.6.1 Where corbeling is required for the support
of some structural element, maximum projection of 7.3 Mortar
masonry unit should not exceed one-half of the
height of the unit or one-half of the built-in part of 7.3.1 Mortars, such as those given in Table 13 or of
the unit and the maximum horizontal projection of equivalent specification, shall preferably be used for
the corbel should not exceed one-third of the wall masonry construction for various categories of
thickness. buildings.

24 NATIONAL BUILDING CODE OF INDIA


Table 13 Recommended Mortar Mixes the toothed joint should be made in both the walls
(Clauses 7.3.1 and 7.4.6) alternatively in lifts of about 450 mm (see Fig. 14).

Category of Proportion of Cemet-Lime-Sand*)


Construction]l
(1) (2)

A M2 (Cement-sand 1:6) or
M3 (Lime-cinder 3) 1:3) or richer
B, C M2 (Cement-lime-sand 1:2:9 or
Cement-sand 1:6) or richer
D, E H2 (Cement-sand 1:4) or
Ml (Cement-lime-sand 1:1:6) or richer

NOTE — Though the equivalent mortar with lime will have


less strength at 28 days, their strength after one year will be
comparable to that of cement mortar.
1) Category
of construction is defined in Table 12.
‘) Mortar grades and specification for types of limes etc. shall
be in accordance with Table 1.
N In this ~a~e some other pozzolanic material like SURKHZ
(burnt brick fine powder) may be used in place of cinder.
All dimensions in rrrillimetres.
..
7.3.2 Where steel reinforcing bars are provided in FIG. 14 ALTERNATINGTOOTHEDJOINTSIN WALLS
masonry the bars shall be embedded with adequate AT CORNERANDT-JUNCTION
cover in cement sand mortar not leaner than 1:3
7.4.5 Ignoring tensile strength, free standing walls
(minimum clear cover 10 mm) or in cement concrete
of grade M 15 (minimum clear cover 15 rnm or bar shall be checked against overturning under the action
diameter whichever more), so as to achieve good bond of design seismic coefficient cx~allowing for a factor
and corrosion resistance. of safety of 1.5.

7.4.6 Panel or filler walls in framed buildings shall be


7.4 Walls
properly bonded to surrounding framing members by
7.4.1 Masonry bearing walls built in mortar, as means of suitable mortar (see Table 13) or connected
specified in 7.3.1 unless rationally designed as through dowels. If the walls are so bonded they shall
reinforced masonry shall not be built of greater height be checked according to 7.4.3 otherwise as in 7.4.5.
than 15 m subject to a maximum of four storeys when
measured from the mean ground level to the roof slab 7.5 Openings in the Bearing Walls
or ridge level. The masonry bearing walls shall be 7.5.1 Door and window openings in walls reduce their
reinforced in accordance with 7.6.1. lateral load resistance and hence, should preferably be
7.4.2 The bearing walls in both directions shall be small and more centrally located. The guidelines on
straight and symmetrical in plan as far as possible. the size and position of opening are given in Table 14
and Fig. 15.
7.4.3 The wall panels formed between cross walls and
floors or roof shall be checked for their strength in 7.5.2 Openings in any storey shall preferably have
bending as a plate or as a vertical strip subjected to the their top at the same level so that a continuous band
earthquake force acting on its own mass. could be provided over them, including the lintels
throughout the building.
NOTE — For panel walls of 200 mm or larger thickness having
a storey height not more than 3.5 m and laterally supported at 7.5.3 Where openings do not comply with the
the top, this check need not be exercised. guidelines of Table 14, they should be strengthened
7.4.4 Masonry Bond by providing reinforced concrete or reinforcing the
brickwork, as shown in Fig. 16 with high strength
For achieving full strength of masonry, the usual bonds
deformed steel bars of 8 mm diameter but the quantity
specified for masonry should be followed so that the
of steel shall be increased at the jambs to comply
vertical joints are broken properly from course to
with 7.6.9, if so required.
course. To obtain full bond between perpendicular
walls, it is necessary to make a slopping (stepped) joint 7.5.4 If a window or ventilator is to be projected out,
by making the comers first to a height of 600 mm and the projection shall be in reinforced masonry or
then building the wall in between them. Otherwise, concrete and well anchored.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 25


Table 14 Size and Position of Openings in Bearing Walls
(Clause 7.5.1 and Fig. 15)

S1 Position of Opening Details of Opening for Building Category


No. F A %
Aand B c D and E
(1) (2) (3) (4) (5)

i) Distance IZ from the inside corner of outside wall, Min o 230 mm 450 mm
ii) For total length of openings, the ratio (bl + bz + b~)i 11or
(bc + b7)/ 12shall not exceed:
a) one-storeyed building 0.60 0.55 0.50
b) two-storeyed building 0.50 0.46 0.42
c) three or four-storeyed building 0.42 0.37 0.33
iii ) Pier width between consecutive openings bl, Min 340 mm 450 mm 560 mm
iv) Vertical distance between two openings one above the other hs, Min 600 mm 600 mm 600 mm
v) Width of opening of ventilator bg, Max 900 mm 900 mm 900 mm
#

A=
/1 /2 -t

4- /-4

be
r- -1
I I
3 1’
7
!ti I-%hin-%ll-% l-%
r
El:El-t DI
K
1 1 ‘z 2

‘I L
bs
4 b’
I
— I I I I
77y\v// //A\V// //A\V// /m /// /zws-//
1. DOOR 2. WINDOW 3. VENTILATOR 4. CROSS WALL

FIG. 15 RECOMMENDED
DIMENSIONS
OFOPENINGSANDPIERS(see Table 14)

SECTION AT XX 1

40 d 40 d

w= WINDOW h = THICKNESS OF CONCRETE IN JAMB


t = WALL THICKNESS V= VERTICAL BAR
ti= LINTEL THICKNESS d = DIAMETER OF REINFORCING BARS

FIG. 16 STRENGTHENING
MASONARYAROUNDOPENING

26 NATIONAL BUILDING CODE OF INDIA

..
7.5.5 If an opening is tall from bottom to almost top levels, vertical reinforcing bars at comers, junctions
of a storey, thus dividing the wall into two portions, of walls and jambs of opening.
these portions shall be reinforced with horizontal
7.6.2 Lintel band is a band provided at lintel level on
reinforcement of 6 mm diameter bars at not more than
all load bearing internal, external longitudinal and cross
450 mm intervals, one on inner and one on outer face,
walls. The specifications of the band are given in 7.6.3.
properly tied to vertical steel at jambs, corners or
junction of walls, where used. NOTE — Lintel band if provided in panel or partition walls
also will improve their stability during severe earthquake.
7.5.6 The use of arches to span over the openings is a
7.6.3 Roof band is a band provided immediately below
source of weakness and shall be avoided. Otherwise,
the roof or floors. The specifications of the band are
steel ties should be provided.
given in 7.6.5. Such a band need not be provided
7.6 Seismic Strengthening Arrangements underneath reinforced concrete or brick-work slabs
resting on bearing walls, provided that the slabs are
7.6.1 All masonry buildings shall be strengthened by
continuous over the intermediate wall up to the crumple
the methods, as specified for various categories of
sections, if any, and cover the width of end walls, fully
buildings, as listed in Table 15, and detailed
or at least 74 of the wall thickness.
in subsequent clauses. Figures 17 and 18 show,
schematically, the overall strengthening arrangements 7.6.4 Gable band is a band provided at the top of gable
to be adopted for category D and E buildings which masonry below the purlins. The specifications of the
consist of horizontal bands of reinforcement at critical band are given in 7.6.5. This band shall be made
continuous with the roof band at the eaves level.
Table 15 Strengthening Arrangements
7.6.5 Section and Reinforcement of Band
Recommended for Masonry Buildings
(Rectangular Masonry Units) The band shall be made of reinforced concrete of grade
(Clause 7.6.1) not leaner than M 15 or reinforced brickwork in cement
mortar not leaner than 1:3. The bands shall be of the
Building Number of Strengthening to tw full width of the wall, not less than 75 mm in depth
Category Storeys Provided in all Storeys
and reinforced with steel, as indicated in Table 16.
(1) (2) (3)
NOTE — In coastal areas, the concrete grade shall be M20
A i) 1t03 a concrete and the tllhng mortar of 1:3 (cement sand with water
ii) 4 a, b, c proofing admixture).
B i) lto3 a, b,c, jg
ii) 4 a, b,c, d,~g
Table 16 Recommended Longitudinal Steel in
c i) 1 and 2 a, b, c, f, g
ii) 3 and 4 atog Reinforced Concrete Bands .
D i) land2 atog
(Clauses 7.6.5 and 7.8.1 and Table 17)
ii) 3and4 atoh
E 1 to 3’) atoh
span Building Building BailrWg Building
where Category category category category
/
a – Masonry mortar (see 7.3)
ALLA
b - Lintel band (see 7.6.2) No. of Dia No.’of Dia No. of Dia No, of Dia
c – Roof band and gable band where necessary (see 7.6.3 Bars Bars Bsrs Bars
and 7.6.4), m mm ,mnr mm mm
d - Vertical steel at comers andjunctions of wafls (see 7.6.8) (1) (2) (3) (4) (5) (6) (7) (8) (9)
e – Vertical steel at jambs of openings (see 7.6.9)
5orless 28282 8210
f - Bracing in plan at tie level of roofs 2 ;.8 2 10 2 12
6 28
g – Plinth band where necessary (see 7.6.6), and 7 2 8 2 10 2 12 4 10
h - Dowel bars (see 7.6.7) 8 2 10 2 12 4 10 4 12
1}Foufi storey not allowed in category E.
NOTES
NOTE — In case of four storey buildings of category
1 Span of wafl will be the distance between cerstre lines of its
B, the requirements of verticaf steel may be checked cross watts or buttresses. For spans greater than 8 m it will be
through a seismic analysis using a design seismic desirable to insert pilasters or buttresses to reduce the span or
coefficient equal to four times the one given in good
speciat calculationsshall be nta& to determine the strength of
practice [6-4(8)] (this is because the brittle behaviour wsfl and SeCtiOll of baad.
of masonry in the absence of a verticaf steel results in
2 The numb& artd diameter of bars given above pertain to
much higher effective seismic force than that envisaged
high strength deformed bars. If plain mild steel bars are used
in the seismic coefficien~ provided in the Code). If this
keeping the ssme number, the following diameters maybe used
analysis shows that vertical steel is not required the
designer may take the decision accordingly. High strength deformed 8 10 12 16 20
steel bar dhtneter

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 27


f2

\3

1. LINTEL BAND 4. DOOR


2. ROOF FLOOR BAND 5. WINDOW
3. VERTICAL BAR

FIG. 17 OVERALL ARRANGEMENTOF REINFORCINGMASONRY BUILDINGS

mm

(B)
1. LINTEL BAND 8. HOLDING DOWN BOLT
2. EAVE LEVEL (ROOF) BAND 9. BRICIUSTONE WALL
3. CABLE BAND 10. DOOR LINTEL INTEGRATE
4. DOOR WITH ROOF BAND
5. WINDOW
6. VERTICAL STEEL BAR
7. RAFTER

18A PERSPECTIVE VIEW


18B DETAILS OF TRUSS CONNECTION WITH WALL
18C DETAILS OF INTEGRATING DOOR LINTEL WITH ROOF BAND

FIG. 18 OVERALL ARRANGEMENTOF REINFORCINGMASONRY BUILDING


HAVING PITCHEDROOF

28 NATIONAL BUILDING CODE OF INDIA


Table 16 — Concluded 7.6.6 Plinth band is a band provided at plinth level of
walls on top of the foundation wall. This is to be
Mild steel plain deformed 10 12 16 20 25
bar diameter
provided where strip footings of masonry (other than
reinforced concrete or reinforced masonry) are used
3 Width of RC band is assumed same as the thickness of the
wall. Wall thickness shall be 200 mm minimum. A clear cover and the soil is either soft or uneven in its properties, as
of 20 mm from face of wall will be maintained. frequently happens in hill tracts. Where used, its section
4 The vertical thickness of RC band be kept 75 mm minimum, may be kept same as in 7.6.5. This band will serve as
where two longitudinal bars are specified, one on each Face: damp proof course as well.
and 150 mm, where four bars are specified.
5 Concrete mix shall be of grade M 15 or 1:2:4 by volume. 7.6.7 In category D and E buildings, to further iterate
6 The longitudinal steel bars shall be held in position by steel the box action of walls, steel dowel bars may be used
links or stirrups 6 mm dia spaced at 150 mm apart. at corners and T-junctions of walls at the sill level of
windows to a length of 900 mm from the inside corner
7.6.5.1 In case of reinforced brickwork, the thickness in each wall. Such dowel may be in the form of U
of joints containing steel bars shall be increased so as stirrups of 8 mm diameter. Where used, such bars shall
to have a minimum mortar cover of 10 mm around the be laid in 1:3 cement-sand-mortar with a minimum
bar. In bands of reinforced brickwork the area of steel cover of 10 mm on all sides to minimize corrosion.
provided should be equal to that specified above for
reinforced concrete bands. 7.6.8 Vertical Reinforcement

7.6.5.2 For full integrity of walls at corners and junctions Vertical steel at corners and junctions of walls, which
of walls and effective horizontal bending resistance of are up to 340 mm ( 1!42 brick) thick, shall be provided as
bands continuity of reinforcement is essential. The specified in Table 17. For walls thicker than 340 mm,
details as shown in Fig. 19 are recommended. the area of the bars shall be proportionately increased.

3060 t GO 30

19A SECTION OF BAND WITH TWO BARS 19B SECTION OF BAND WITH FOUR BARS

bl bz
t--i t-1

19C STRUCTURAL PI.AN OF


I b2

19D SECTION PLAN AT T-JUNCT!ON


CORNER JUNCTION
OF WALL

1. Longitudinal bars
2. Lateral ties
bl, b2- Wall thickness
All dimensions in millimetres.

FIG. 19 REINFORCEMENTAND BENDINGDETAIL IN R.C. BAND

P.&RT 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 29

..
Table 17 Vertical Steel Reinforcement in Masonry Walls with
Rectangular Masonry Units
(Clauses 7.6.8,7.6.9 and 8.7.2)

No. of Storeys Storey Diameter of HSD Single Bar in mm at Each Critical Section

Category B Category C Category D Category E

(1) (2) (3) (4) (5) (6)

One — Nil Nil 10 12

Two Top Nil Nil 10 12


Bottom Nil Nil 12 16

Three Top Nil 10 10 12


Middle Nil 10 12 16
Bottom Nil 12 12 16

Four Top 10 10 10
Third 10 10 12 Four storeyed
Second 10 12 building not
16
Bottom 12 12 20 permitted

NOTES
1 The diameters given above are for high strength deformed steel bars. For mild steel plain bars, use equivalent diametcm as given in
Table 16 (Note 2).
2 The vertical bars will be covered with concrete M 15 or mortar 1:3 grade in suitably ermted pockets around the bars. This will
ensure their safety from corrosion and good bond with masonry.
3 In case of floors/roofs with small precast components, also refer good practice [6-4(8)] for floorhoofband details.

For earthquake resistant framed wall construction, beams are located at all floors, roof as well as lintel
(see 7.7). No vertical steel need be provided in levels of the openings. The sequence of construction
category A buildings. between walls and columns will be first to build the
wall up to 4 to 6 courses height leaving toothed gaps
7.6.8.1 The vertical reinforcement shall be properly
(tooth projection being about 40 mm only) for the
embedded in the plinth masonry of foundations and
columns and second to pour Ml 5 (1:2:4) concrete to
roof slab or roof band so as to develop its tensile
fill the columns against the walls using wood forms
strength in bond. It shall be passing through the lintel
only on two sides. The column steel should be
bands and floor level bands in all storeys.
accurately held in position all along. The band
Bars in different storeys may be welded or suitably concrete should be cast on the wall masonry directly
lapped. so as to develop full bond with it.
NOTE — Typical details of providing vertical steel in Such construction may be limited to only two storeys
brickwork masonry with rectangular solid units at corners and maximum in view of its vertical load carrying capacity.
T-junctions are shown in Fig. 20.
The horizontal length of walls between cross walls shall
7.6.9 Vertical reinforcement at jambs of window and be restricted to 7 m and the storey height to 3 m.
door openings shall be provided as per Table 17. It
may start from foundation of floor and terminate in 7.8 Reinforcing Details for Hollow Block Masonry
lintel band (see Fig. 21). The following details may be followed in placing the
J,
horizontal and vertical steel in hollow block masonry ,
7.7 Framing of Thin Load Bearing Walls (see
using cement-sand or cement-concrete blocks.
Fig. 21)
7.8.1 Horizontal Band
Load bearing walls can be made thinner than 200 mm
say 150 mm inclusive of plastering on both sides. U-shaped blocks may be used for construction of
Reinforced concrete framing columns and collar horizontal bands in various levels of the storeys as
beams will be necessary to be constructed to have shown in Fig. 22, where the amount of horizontal
full bond with the walls. Columns are to be located at reinforcement shall be taken 25 percent more than that
all corners and junctions of walls and spaced not more given in Table 16 and provided by using four bars and
than 1.5 m apart but so located as to frame up the 6 mm dia stirrups. Other continuity details shall be
doors and windows. The horizontal bands or ring followed, as shown in Fig. 19.

30 NATIONAL BUILDING CODE OF INDIA

..
I I

-t-3-w--- L_-,;+ A

In_ .
1/2
1~
v
1~
1/2
E
1<
J’

r ‘ “1

+4+-
I-1-l-l-l-l--l
(a)
(b)
I-+1

m L
W_
lg
W_
1/2 I

“’%%ikrmn
11/
/-v
1
1
1
1
1
1
tl I 1 141 1

(c) (d)

1/2 I I I
1/4

(e) (9

1 — One-brick length, k — Half brick length, V — Vertical steel bar with mortar/concrete filling in pocket
(a) and (b) — Alternate courses in one brick
(c) and (d) – Alternate courses at cornerjunction ofl%-brickwall
(c)and(f) —Alternate courses atT-junction ofl%-btick wall

FIG. 20 TYPICAL DETAILS OF PROVIDINGVERTICAL STEEL BARS


INBRICKMASONRY

PART6 STRUCTURALI.)ESIGN-SECTION 4 MASONRY


31

..
“-” f-’

2000

1. WINDOW
2. DOOR
3. BRICK PANEL
4. LINTEL BAND

All dimensionsin millimetres.

FIG. 21 FRAMING OF THIN LOAD-BEARING BRICK WALLS

32 NATIONAL BUILDING CODE OF INDIA


FIG. 22 U-BLOCKS FOR HORIZONTAL BANDS

7.8.2 Vertical Reinforcement a) Brick construction using weak mortar, and

Bars, as specified in Table 17 shall be located inside b) Random rubble and half-dressed stone
the cavities of the hollow blocks, one bar in each cavity masonry construction using different mortars,
(see Fig. 23). Where more than one bar is planned these such as, clay mud, lime-sand and cement
can be located in two or three consecutive cavities. sand.
The cavities containing bars are to be filled by using 8.1.2 These constructions should not be permitted for
micro-concrete 1:2:3 or cement-coarse sand mortar 1:3, important buildings with 121.5 and should preferably
and properly rodded for compaction. The vertical bars be avoided for building category D and shall not be
should be spliced by welding or overlapping for used for category E (see Table 12).
developing full tensile strength. For proper bonding,
the overlapped bars should be tied together by winding 8.1.3 It will be useful to provide damp-proof course
the binding wire over the lapped length. To reduce the at plinth level to stop the rise of pore water into the
number of overlaps, the blocks maybe made U-shaped superstructure.
as shown in Fig. 23 which will avoid lifting and 8.1.4 Precautions should be taken to keep the rain
threading of bars into the hollows. water away from soaking into the wall so that the
mortar is not softened due to wetness. An effective
8 GUIDELINES FOR IMPROVING
way is to take out roof projections beyond the walls
EARTHQUAKE RESISTANCE OF LOW
by about 500 mm.
STRENGTH MASONRY BUILDINGS
8.1.5 Use of a water-proof plaster on outside face of
8.0 The term ‘low strength masonry’ includes fired
walls will enhance the life qfthe building and maintain
brickwork laid in clay mud mortar and random rubble;
its strength at the time of earthquake as well.
uncoursed, undressed or semi-dressed stone masonry
in weak mortars; such as cement sand, lime sand and 8.1.6 Ignoring tensile strength, free standing walls
clay mud. Special features of design and construction should be checked against overturning under the action
for improving earthquake resistance of buildings of of design seismic coefficient, ah, allowing for a factor
low strength masonry are given in 8.1 to 8.4.7. of safety of 1.5.
Reference may also be made to good practice [6-4(9)]
for detailed information. 8.2 Brickwork in Weak Mortars

8.1 General 8.2.1 The fired bricks should have a compressive


strength not less than 3.5 MPa. Strength of bricks and
8.1.1 Two types of construction are included herein, wall thickness should be selected for the total buildlng
namely: height.

PARr 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 33


u r

o
0;.
~
,.’.
4“
....
I .. ,
I
[—][—]@l[-J[-]
I

l-’’===
[—] [—’
/

u n
u ..

c1
u I
●

El
4
,a..

@El
G WIRE

FIG. 23 VERTICALREINFORCEMENT
IN CAVITIES

8.2.2 The mortar should be lime-sand (1:3) or clay a) For Categories A, B and C — three storeys
mud of good quality. Where horizontal steel is used with flat roofi and two storeys plus attic for
between courses, cement-sand mortar (1:3) should be pitched roof.
used with thickness so as to cover the steel with 6 mm b) For Category D — two storeys with flat roofi
mortar above and below it. Where vertical steel is used, and one storey plus attic for pitched roof.
the surrounding brickwork of 1 x 1 or 1Y2 x 1Y2 brick
size depending on wall thidcness should preferably be 8.2.5 Special Bond in Brick Walls
built using 1:6 cement-sand mortar.
For achieving full strength of masonry, the usual
8.2.3 The minimum wall thickness shall be one brick bonds specified for masonry should be followed so
in one storey construction, and one brick in top storey that the vertical joints are broken properly from course
and 1?4 brick in bottom storeys of up to three storey to course. To obtain full bond between perpendicular
construction. It should also not be less than 1/16 of the walls, it is necessary to make a sloping (stepped)
length of wall between two consecutive perpendicular joint by making the corners first to a height of
walls. 600 mm and then building the wall in between them.
8.2.4 The height of the building shall be restricted to Otherwise the toothed joint should be made in both
the following, where each storey height shall not the walls, alternatively in lifts of about 450 mm (see
exceed 3.0 m: Fig. 14).

34 NATIONAL BUILDING CODE OF INDIA

..
L
8.3 Stone Masonry (Random Rubble or Half- preservative so that it is durable against weathering
Dressed) and insect action.

8.3.1 The construction of stonemasonry of random 8.3.7 Use of ‘bonding’ elements of adequate length
rubble or dressed stone type should generally follow should also be made at comers and junctions of walls
good practice [6-4(3)]. to break the vertical joints and provide bonding
between perpendicular walls.
8.3.2 The mortar should be cement-sand (1:6), lime
sand (1:3) or clay mud of good quality. 8.3.8 Height of the stonemasonry walls (random rubble
or half-dressed) should be restricted as follows, with
8.3.3 The wall thickness ‘t’should not be larger storey height to be kept 3.0 m maximum, and span of
than 450 mm. Preferably it should be about 350 mm, walls between cross walls to be limited to 5.0 m:
and the stones on the inner and outer wythes should be
interlocked with each other. a) For categories A and B — Two storeys with
flat roof or one storey plus attic, if walls are
NOTE -– If the two wythes are not interlocked, they tend to
built in lime-sand or mud mortar; and one
delaminate during ground shaking bulge apart (see Fig. 24)
and buckle separately under vertical load leading to complete storey higher if walls are built in cement-sand
collapse of the wall and the building. 1:6 mortar.
b) For categories C and D — Two stroreys with
flat roof or two storeys plus attic for pitched
roof, if walls are built in 1:6 cement mortar;
and one storey with flat roof or one storey
plus attic, if walls are built in lime-sand or
mud mortar, respectively.

8.3.9 If walls longer than 5 m are needed, buttresses


may be used at intermediate points not farther apart
than 4.0 m. The size of the buttress be kept of uniform
thickness. Top width should be equal to the thickness
of main wall, t,and the base width equal to one-sixth
of wall height.

8.4 Opening in Bearing Walls


1.Half-cressed conical stone
8.4.1 Door and window openings in walls reduce their
2. Small alignment stone
Rotation of wythe
lateral load resistance and hence should preferably, be
3.
4. Random rubble small and more centrally located. The size and position
5. Mud or weak lime mortar of openings shall be as given in Table 18 and Fig. 15.
.
FIG. 24 WALL DELAMINATED
WITH 8.4.2 Openings in any storey shall preferably have
BUCKLEDWYTHES their top at the same level so that a continuous band
could be provided over them including the lintels
8.3.4 The masonry should preferably be brought to
throughout the building.
courses at not more than 600 mm lift.
Table 18 Size and Position of Openings in
8.3.5 ‘Through’ stones of full length equal to wall
Bearing Walls (see Fig. 15)
thickness should be used in every 600 mm lift at not
more than 1.2 m apart horizontally. If full length stones (Clause 8.4.1)
are not available, stones in pairs each of about % of s] Description Building Category
the wall thickness may be used in place of one full No. A
r 7
length stone so as to provide an overlap between them A, B&C D
(1) (2) (3) (4)
(see Fig. 25).
i) Distance b5from the inside comer of 230 mm 600 mm
8.3.6 In place of ‘through’ stones, ‘bonding elements’ outside wall, A4in
of steel bars 8 mm to 10 mm diameter bent to S-shape ii) Total length of openings, ratio; Max:
or as hooked links maybe used with a cover of 25 mm (b, + bz + bJ/2, or (b, + b7)/lz 0.46 0.42
1) one storeyed building 0.37 0.33
from each face of the wall (see Fig. 25). Alternatively, 2) 2 and 3 storeyed building
wood bars of 38 mm x 38 mm cross-section or concrete iii) Pier width between consecutive 450 mm 560 mm
bars of 50 mm x 50 mm section with an 8 mm diameter openings b4 ‘“
iv) Vertical distance between two 600 mm 600 mm
rod placed centrally may be used in place of ‘through’
openings one above the other, h3, hlin
stones. The wood should be well treated with

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 35


T
900

25a SECTIONAL PLAN OF WALL 25b CROSS-SECTION OF WALL

1. Through stone 4. Hooked tie


2. Pair of overlapping stone 5. Wood plank
3. S-Shape tie 6. Floor level

All dimensions in millimetres.

FIG. 25 THROUGHSTONEANDBANDELEMENTS

8.4.3 Where openings do not comply with the Table 19 Strengthening Arrangements
guidelines of Table 18, they should be strengthened Recommended for Low Strength
by providing reinforced concrete lining as shown in lvkonry Buildings
Fig. 16 with 2 high strength deformed steel bars of (Clause 8.5.1)
8 mm diameter.
Building Category Number of Storeys Strengthening to .
8.4.4 The use of arches to span over the openings is a be Provided
.6
source of weakness and shall be avoided, otherwise, (1) (2) (3)
steel ties should be provided.
A 1 b,c, jg
2and3 b,c, ~g
8.5 Seismic Strengthening Arrangements
B land2 b,c, $g
8.5.1 All buildings to be constructed of masonry shall 3 b,c, d,~g
be strengthened by the methods as specified for various (see Note 1)

categories of buildings, listed in Table 19 and detailed c 1 b, c, f,g


in subsequent clauses. Fig. 17 and Fig. 18 show, 2and3 b,c, d,~g
D 1 and 2 b,c, d,~g
schematically, the overall strengthening arrangements
to be adopted for category D buildings, which consist Strengthening Method

of horizontal bands of reinforcement at critical levels b- Lintel band (see 8.5.2)


and vertical reinforcing bars at corners and junctions c– Roof band and gable band where necessary (see 8.5.3
of walls. and 8.5.4)
d- Vertical steel at ccmers and junctions of walls
8.5.2 Lintel band is a band provided at lintel level on (see 8.5.7)
all internal and external longitudinal as well as cross f- Bracing in plan at tie level of pitched roofs (see
walls except partition walls. The details of the band Note 2)
are given in 8.5.5. g– Plinth band where necessary (see 8.5.6)

8.5.3 Roof band is a band provided immediately below NOTES

the roof or floors. The details of the band are given 1 For building of category B in two storeys constructed with
stone masonry in weak mortar, it will be desirable to provide
in 8.5.5. Such a band need not be provided underneath
vertical steel of 10 mm dia in both storeys.
reinforced concrete or reinforced brick slabs resting
2 At tie level, all the trusses and the gable end should be
on bearing walls, provided that the slabs cover the provided with diagonal braces in plan so as to transmit the
width of end walls fully. lateral shear due to earthquake force to the gable walls acting
as shear walls.
8.5.4 Gable band is a band provided at the top of gable

36 NATIONAL BUILDING CODE OF INDIA

..
masonry below the purlins. The details of the band are could be provided using wood beams in one or two
given in 8.5.5. This band shall be made continuous parallel pieces with cross elements as shown in
with the roof band at the eaves level. Fig. 26.

8.5.5 Lktails t#Band 8.5.6 Plinth band is a band provided at plinth level of
walls on top of the foundation wall. This is to be
8.5.5.1 Reinforced bund
provided where strip footings of masonry (other than
The band should be made of reinforced concrete of reinforced concrete or reinforced masonry) are used
grade not leaner than M 15 or reinforced brickwork in and the soil is either soft or uneven in its properties as
cement mortar not leaner than 1:3. The bands should frequently happens in hill tracts. Where used, its section
be of full width of the wall, not less than 75 mm in may be kept same as in 8.5.5.1. This band serves as
depth and should be reinforced with 2 high strength damp proof course as well.
deformed steel bars of 8 mm diameter and held in
8.5.7 Vertical Reinforcement
position by 6 mm diameter bar links, installed at
150 mm apart as shown in Fig. 19. Vertical steel at comers and junctions of walls which
are up to 350 mm thick should be provided as specified
NOTES
in Table 20. For walls thicker than 350 mm, the area
1 [n coastal areas, the concrete grade shall be of grade in
accord~ncewith Part 6 ‘StructuralDesign,Section5 Concrete’ of the bars should be proportionately increased.
and the filling mortar of 1:3 ratio (cement-sand)with water
8.5.7.1 The vertical reinforcement should be properly
proofing admixture.
embedded in the plinth masonry of foundations and
2 In case of reinforced brickwork, the thickness of joints
containing steel bars should be increased to 20 mm so as to roof slab or roof band so as to develop its tensile .—
havea minimummortarcoverof 6 mmaroundthe bar. In bands strength in bond. It should pass through the lintel
of reinforcedbrickwork,the area of steel provided should be bands and floor slabs or floor level bands in all
equal to that specified above for reinforced concreteb~ds. storeys. Bars in different storeys may be welded or
3 For full integrityof walls at comers and junctions of walls
suitably lapped.
andeffectivehorizontalbendingresistanceof bands,continuity
of reinforcementis essential, The details as shown in Fig. 19 NOTES
arc recommended. 1 Typical details of providing vertical steel in brickwork at
comers and T-junctionsare shownin Fig. 20.
8.5.5.2 Wooden band
2 For providingverticalbar in stone masonry,use of a casing
As an alternative to reinforced band, the lintel band pipe is recommendedaroundwhichmasonrybe built to height

1---1 8

~T -15X367
I I I 1500
75x3

IrlF
. ..

00

. ..
-1-

500+- 500+-5 . .

.
~75x38 .
26b PLAN OF BAND

All dimensionsin millimetres.

FIG. 26 WOODENBAND FORLow STRENGTHMASONRYBUILDINGS

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 37


Table 20 Vertical Steel Reinforcement in Low Strength Masonry Walls
(Clause 8.5.7)

No. of Storey Diameter of HSD Single Bar; in mm, at Each Critical Section for
Storeys
/
Category A Catego~ B Category C Category D
(1) (2) (3) (4) (5) (6)
One — Nil Nil Nil 10
Two Top Nil Nil 10 10
Bottom Nil Nil 10 12
Three Top Nil 10 10 10
Middle Nil 10 10 12
Bottom Nil 12 12 12

NOTES
1 The diameters given above are for High Strength Deformed bars with yield strength 415 MPa. For mild steel plain bars, use
equivalent diameters.
2 The vertical bars should be covered with concrete of M15 grade or with mortar 1:3 (cement-sand) in suitably created pockets around
the bars. This will ensure their safety from corrosion and good bond with masonry.
3 For category B two storey stone masonry buildings, see Note 1 under Table 19.

of 600 mm (see Fig. 27). The pipe is kept loose by rotating it reinforced brick concrete floors and roof shall be in
during masonry construction. It is then raised and the cavity
accordance with good practices [6-4(10)].
below is filled with Ml 5 (or 1:2:4) grade of concrete mix and
rodded to compact it.
10 NOTATIONS AND SYMBOLS
9 REINFORCED BRICK AND REINFORCED
The various notations and letter symbols used in the
BRICK CONCRETE FLOORS AND ROOFS
text of this Section of the Code shall have the meaning
The construction and design of reinforced brick and as given in Annex E.

+t=~”-

3 I
1. Stone wall 3. Casing pipe
2. Vertical steel bar 4. Through stone or bonding element

FIG. 27 TYPICAL CONSTRUCTION DETAIL FOR INSTALLING VERTICAL STEEL BAR IN


RANDOM RUBBLE STONE MASONRY

38 NATIONAL BUILDING CODE OF INDIA

..
ANNEX A

(Clause 4.7)
SOME GUIDELINES FOR ASSESSMENT OF ECCENTRICITY OF
LOADING ON WALLS

A-1 Where a reinforced concrete roof and floor slab valid also for interior walls carrying independent slabs
of normal span (not exceeding 30 times the thickness spanning from both sides, provided the span of the floor
of wall) bear on external masonry walls, the point of on one side does not exceed that on the other by more
application of the vertical loading shall be taken to than 15 percent. Where the difference is greater, the
be at the centre of the bearing on the wall. When the displacement of the point of application of each floor
span is more than 30 times the thickness of wall, the load shall be’taken as one-sixth of its bearing width on
point of application of the load shall be considered the wall and the resultant eccentricity calculated
to be displaced from the centre of bearing towards therefrom.
the span of the floor to an extent of one-sixth the
A-5 For timber and other lightweight floors, even for
bearing width.
full width bearing on wall, an eccentricity of about
A-2 In case of a reinforced concrete slab of normal one-sixth may be assumed due to deflection. For timber
span (that is, less than 30 times the thickness of the floors with larger spans, that is, more than 30 times
wall), which does not bear on the full width of the wall the thickness of the wall, eccentricity of one-third the
and ‘cover tiles or bricks’ are provided on the external thickness of the wall may be assumed.
face, there is some eccentricity of load. The eccentricity
A-6 In multi-storeyed buildings, fixity artd eccentricity
may be assumed to be one-twelfth of the thickness of
have normally purely local effect and are not
the wall.
cumulative. They just form a constant ripple on the
A-3 Eccentricity of load from the roof/floor increases downward increasing axial stress. If the ripple is large,
with the increase in flexibility and thus deflection of it is likely to be more serious at upper levels where it
the slabs. Also, eccentricity of loading increases with can cause cracking of walls than lower down where it
the increase in fixity of slabs/beams at supports. may or may not cause local over-stressing.
Precast RCC slabs are better than in-situ slabs in this
NOTE — The resultant eccentricity of the total loads on a
regard because of very little fixity. If supports are
wall at any level may be calculated on the assumption that
released before further construction on top, fixity is immediately above a horizontal lateral support, the resultant
reduced. eccentricity of all the verticat loads above that level is zero.

A-4 Interior walls carrying continuous floors are A-7 For a wall corbel to support some load, the point
assumed to be axially loaded except when carrying of application of the load shall be assumed to be at the
very flexible floor or roof systems. The assumption is centre of the bearing on the corbel.

ANNEX B

(Clause 5.4.1)

CALCULATION OF BASIC COMPRESSIVE STRESS OF


MASONRY BY PRISM TEST

B-1 DETERMINATION OF COMPRESSIVE of mortar joints and workmanship shall be the same
STRENGTH OF MASONRY BY PRISM TEST as will be used in the structure. Assembled specimen
shall be at least 400 mm high and shall have a height
When compressive strength of masonry (~~) is to be
to thickness ratio (h/t) of at least 2 but not more than
established by tests, it shall be done in advance of
5. If the h/t ratio of the prisms tested is less than 5 in
the construction, using prisms built of similar
materials under the same conditions with the same case of brickwork and more than 2 in case of
bonding arrangement as for the structure. In building blockwork, compressive strength values indicated by
the prisms, moisture content of the units at the time the tests shall be corrected by multiplying with the
of laying, the consistency of the mortar, the thickness factor indicated in Table 21.

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 39


Table 21 Correction Factors for Different area of the prism, in a testing machine, the upper
M Ratios platform of which is spherically seated. The load shall
(Clause B-1.1) be evenly distributed over the whole top and bottom
surfaces of the specimen and shall be applied at the
Ratio of Height to 2.0 2.5 3.0 3.5 4.0 5.0
Thickness (/s/t) rate of 350 kN/m to 700 kN/m. The load at failure
Correction Factors 0.73 O.~0 0.86 0.91 0.95 1.00 should be recorded.
for Brickwork’)
Correction Factors 1.00 — 1.20 — 1.30 1.37 B-2 CALCULATION OF BASIC COMPRESSIVE
for Blockworkl) STRESS

‘‘[nterpd ation is valid for intermediate values. Basic compressive stress of masonry shall be
taken to be equal to 0.25 ~~ where f~ is the value of
Prisms shall be tested after 28 days between sheets of compressive strength of masonry as obtained from
nominal 4 mm plywood, slightly longer than the bed prism test.

ANNEX C

(Clauses 5.3.3 and 5.4.1.5)


GUIDELINES FOR DESIGN OF MASONRY SUBJECTED TO
CONCENTRATED LOADS

C-1 EXTENT OF DISPERSAL OF C-3 CRITERIA OF PROVIDING BED BLOCK


CONCENTRATED LOAD
C-3.1 If a concentrated load bears on one end of a
For concentric loading, maximum spread of a wall, there is a possibility of masonry in the upper
concentrated load on a wall may be taken to be equal region developing tension. In such a situation, the load
to b+4t (b is width of bearing and t is thickness of should be supported on an RCC bed block (of Ml 5
wall), or stretch of wall supporting of load, or centre- Grade) capable of taking tension.
to-centre distance between loads, whichever is less.
C-3.2 When any section of masonry wall is subjected
C-2 INCREASE IN PERMISSIBLE STRESS to concentrated as well as uniformly distributed
load and resultant stress, computed by making due
C-2.1 When a concentrated load bears on a central
strip of wall, not wider than half the thickness of the allowance for increase in stress on account of
concentrated load, exceeds the permissible stress
wall and is concentric, bearing stress in masonry may
exceed the permissible compressive stress by 50 in masonry, a concrete bed block (of M15 Grade)
percent, provided the area of supporting wall is not should be provided under the load in order to
less than three times the bearing area. relieve stress in masonry. In concrete, angle of
dispersion of concentrated load is taken to be 45° to
C-2.2 If the load bears on full thickness of wall and is the vertical.
concentric, 25 percent increase in stress may be
allowed. C-3.3 In case of cantilevers and long span beams
supported on masonry wails, indeterminate but very
C-2.3 For loading on central strip wider than half the high edge stresses occur at the supports and in such
thickness of the wall but less than full thickness,
cases it is necessary to relieve stress on masonry by
increase in stress may be worked out by interpolation
providing concrete bed block of M15 Grade concrete.
between values of increase in stresses as given
Similarly when a wall is subjected to a concentrated
in C-2.1 and C-2.2.
load from a beam which is not sensibly rigid (for
C-2.4 In case concentrated load is from a lintel over example, a timber beam or art RS joist), a concrete bed
an opening, an increase of 50 percent in permissible block should be provided below the beam in order to
stress may be taken, provided the supporting area is avoid high edge stress in the wall because of excessive
not less than 3 times the bearing area. deflection of the beam.

NATIONAL BUILDING CODE OF INDIA


ANNEX D

(Clause 5.5.5)
GUIDELINES FOR APPROXIMATE DESIGN OF NON-LOAD BEARING WALL

D-1 PANEL WALLS Table 23 Bending Moments in Laterally


Loaded Panel Walls Supported
A panel wall maybe designed approximately as under,
on All Four Edges
depending upon its support conditions and certain
assumptions:
‘ei@t Of‘me” H 0.30 0.50 0.75 1.00 1.25 1.50 1.75
a) When there are narrow tall windows on either Lengthof Panel, L
side of panel, the panel spans in the vertical P,L P.L P.L P.L P.L P.L P.L
Bending Moment ~ ~ ~ ~ ~ ~ ~
direction. Such a panel may be designed for
a bending moment of PH18, where P is the
NOTE — When H/L is less than 0.30, value of bending
total horizontal load on the panel and H is the moment in the horizontal direction may be taken as nil and
height between the centres of supports. Panel panel watt may be designed for a bending moment value of
wall is assumed to be simply supported in the PH/8 in the vertical direction; when H/L exceeds 1.75, panel
may be assumedto be spanningin the horizontaldireetionand
vertical direction. designedfor bendingmomentof PLJ8.
b) When there are long horizontal windows
between top support and the panel, the top
D-2 CLTRTAIN WALLS
edge of the panel is free. In this case, the panel
should be considered to be supported on sides Curtain walls may be designed as panel walls taking
and at the bottom, and the bending moment into consideration the actual supporting conditions.
would depend upon height to length ratio of
panel and flexural strength of masonry. D-3 PARTITION WALLS
Approximate values of bending moments in D-3.1 These are internal walls usually subjected to
the horizontal direction for this support much smaller lateral forces. Behaviour of such wall is
condition, when ratio @) of flexural strength similar to that of panel wall and these could, therefore,
of wall in the vertical direction to that in be designed on similar lines. However, in view of
horizontal direction is assumed to be 0.5, are smaller lateral loads, ordinarily these could be
given in Table 22. apportioned empirically as follows:

Table 22 Bending —lVIoments in Laterally Loaded a) Walls with adequate lateral restraint at both
Panel Walls, Free at Top Edge and Supported ends but not at the top:
on Other Three Edges 1) The panel may be of any height, provided
Panel, H
Height of
the length does not exceed 40 times the
0.30 0.50 0.75 1.00 1.25 1.50 1.75 thickness; or
Lengthof Panel, L
2) The panel may be of any length, provided
P.L P.L P.L P.L P.L P.L P.L
Bending Moment ~ ~ ~ ~ ~ ~ ~ the height does not exceed 15 times the
thickness (that is, it may be considered
NOTE — For H/L ratio less than 0.30, the panel should be as a free-standing wall); or
designed as a free-standing watl and for H/L ratio exceeding
1.75, it should be designed as a horizontafty spanning membe] 3) Where the length of the panel is over 40
for a bending moment vatue of P.U8. times and less than 60 times the thickness,
the height pl~s twice the length may not
c) When either there are no window openings exceed 135 times the thickness;
or windows are of ‘hole-in-wall’ type, the b) Walls with adequate lateral restraint at both
panel is considered to be simply supported
ends at the top:
on all four edges. In this case also, amount of
1) The panel may be of any height, provided
maximum bending moment depends on
the length does not exceed 40 times the
height to length ratio of panel and ratio (+u)of
thickness; or
flexural strength of masonry in vertical
direction to that in the horizontal direction. 2) The panel may be of any length, provided
Approximate values for maximum bending the height does not exceed 30 times the
moment in the horizontal direction for thickness; or
masonry with p = 0.50, are given in Table 23. 3) Where the length of the panel is over

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 41


40 times and less than 110 times the of any length, provided the height does not
thickness, the length plus three times the exceed 30 times the thickness.
height should not exceed 200 times the
D-3.2 Strength of bricks used in partition walls should
thickness; and
not be less than 3.5 N/mm2 or the strength of masonry
c) When walls have adequate lateral resistant at units used in adjoining masonry, whichever is less.
the top but not at the ends, the panel may be Grade of mortar should not be leaner than M2.

ANNEX E

(Clause 10)

NOTATIONS, SYMBOLS AND ABBREVIATIONS

E-1 The following notations, letter symbols and k= Shape modification factor
abbreviations shall have the meaning indicated against k; = Stress reduction factor
each, unless otherwise specified in the text of this L= Actual length of wall
Section of the Code:
Ll, L2 = Lower strength mortars
A= Area of a section ?vl~ M2 = Medium strength mortars .
b= Width of bearing P= Total horizontal load
DPC = Damp proof course PL = Plinth level
—
— Resultant eccentricity RCC = Reinforced cement concrete
;b = Basic compressive stress RS = Rolled steel
~= Permissible compressive stress s = Spacing of piers/buttresses/cross walls
df=
Compressive stress due to dead loads Sk = Slenderness ratio
“fs= Permissible shear stress Actual thickness
&’= Compressive strength of masonry (in tp = Thickness of pier
prism test) tw = Thickness of wall
GL = Ground level w= Resultant load
H= Actual height between lateral supports w, = Axial load
H’ = Height of opening W* = Eccentric load
HI, H2 = High strength mortars w = Width of piers/buttresses/cross walls
P
h = Effective height between lateral Ratio of flexural strength of wall in
P=
supports the vertical direction to that in the
k. = Area factor horizontal direction.

LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as “good practice’ and ‘accepted standards’ (1) 1077:1992 Specification for common
in the fulfillment of the requirements of the Code. The burnt clay building bricks
latest version of a standard shall be adopted at the time (jljlh revis;on) -
of enforcement of the Code. The standards listed may 2180:1988 Specification for heavy duty
be used by the Authority as a guide in conformance burnt clay building bricks
with the requirements of the referred clauses in the (third revision)
Code.
2185 Specification for concrete
In the following list, the number appearing in the first masonry units:
column within parentheses indicates the number of the (Part 1): 1979 Hollow and solid concrete
reference in this Part/Section. blocks (second revision)

42 NATIONAL BUILDING CODE OF INDIA


IS No. Title IS No. Title
(Part 2): 1983 Hollow and solid lightweight 2212:1991 Code of practice for brickwork
concrete blocks (first revision) (first revision)
(Part 3) :1984 Autoclave cellular aerated 2572:1963 Code of practice for construction
concrete blocks @-st revision) of hollow concrete block
2222:1991 Specification for burnt clay masonry
perforated building bricks 2849:1983 Specification for non-load
(fourth revision) bearing gypsum partition blocks
2849:1983 Specification for non-load (solid and hollow types) ~irst
bearing gypsum partition blocks revision)
(solid and hollow types) (first 3630:1992 Code of practice for construction
revision) of non-load bearing gypsum
3115:1992 Specification for lime based block partitions (jirst revision)
blocks (second revision) 4326:1993 Code of practice for earthquake
Specification for structural resistant design and construction
3316:1974
granite (jlrst revision) of buildings (second revision)

3620:1979 Specification for laterite stone 6041:1985 Code of practice for construction
block for masonry @rst revision) of autoclave cellular concrete
block masonry t$rst revision)
3952:1988 Specification for burnt clay
hollow blocks for walls and 6042:1969 Code of practice for construction
partitions (second revision) of lightweight concrete block
masonry
4139:1989 Specification for calcium
silicate bricks (second revision) (4) 2212:1991 Code of practice for brickwork
(jlrst revision)
12440:1988 Specification for precast
concrete stone masonry blocks (5) 3414:1968 Code of practice for design
and installation of joints in
12894:2002 Specification for pulverized fuel
buildings
ash lime bricks (first revision)
(6) 4326:1993 Code of practice for earthquake
13757:1993 Specification for burnt clay fly
resistant design and construction
ash building bricks
of buildings (second revision)
(2) 2250:1981 Code of practice for preparation
(7) 1905:1987 Code of practice for structural
and use of masonry mortars @rst
use of un-reinforced masonry
revision)
(third revision)
(3) 1597 Code of practice for construction
(8) 1893 Criteria for earthquake resistant
of stone masonry:
(Part 1): 2002 design of structures: Part 1
(Part 1): 1992 Rubble stone masonry (first General provisions and buildings
revision) ~ifth revision)
(Part2) :1992 Ashlar masonry ~irst revision) (9) 13828:1993 Guidelines for improving
2110:1980 Code of practice for in-situ earthquake resistance of low
construction of walls, in strength masonry buildings
building with soil-cement (first (10) 10440:1983 Code of practice for construction
revision) of RB and RBC floors and roofs

PART 6 STRUCTURAL DESIGN — SECTION 4 MASONRY 43


. ---
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 5 Concrete: 5A Plain and Reinforced Concrete

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 5

SECTION 5A(a) GENERAL

1 SCOPE ... 7
2 TERMINOLOGY ... 7
3 SYMBOLS ... 7

SECTION 5A (b) MATERIALS, WORKMANSHIP,


INSPECTION ANDTESTING

4 MATERIALS ... 8
5 CONCRETE ... 11
6 WORKABILITY OF CONCRETE ... 12
7 DURABILITY OF CONCRETE ... 12
8 CONCRETE MIX PROPORTIONING ... 17
9 PRODUCTION OF CONCRETE ... 18
10 FORMWORK ... 20
11 ASSEMBLY OF REINFORCEMENT ... 21
12 TRANSPORTING, PLACING, COMPACTION AND CURING ... 22
13 CONCRETING UNDER SPECIAL CONDITIONS ... 23
14 SAMPLING AND STRENGTH OF DESIGNED CONCRETE MIX ... 24
15 ACCEPTANCE CRITERIA ... 25
16 INSPECTION AND TESTING OF STRUCTURES ... 25

SECTION 5A (C) GENERAL DESIGN CONSIDERATION

17 BASES FOR DESIGN ... 26


18 LOADS AND FORCES . .. 27
19 STABILITY OF THE STRUCTURE ... 28
20 FIRE RESISTANCE ... 28
21 ANALYSIS ... 28
22 BEAMS ... 31
23 SOLID SLABS ... 33‘
24 COMPRESSION MEMBERS ... 36
25 REQUIREMENTS GOVERNING REINFORCEMENT AND DETAILING ... 37
26 EXPANSION JOINTS ... 45

SECTION 5A (d) SPECIAL DESIGN REQUIREMENTS FOR


STRUCTURAL MEMBERS AND SYSTEMS

27 CONCRETE CORBELS ... 45


28 DEEP BEAMS ... 46
29 RIBBED, HOLLOW BLOCK OR VOIDED SLAB ... 47
30 FLAT SLABS ... 48

2 NATIONAL BUILDING CODE OF INDIA


31 WALLS ... 57
32 STAIRS ... 59
33 FOOTINGS ... 59

SECTION 5A (e) STRUCTURAL DESIGN


(LIMIT STATE METHOD)

34 SAFETY AND SERVICEABILITY REQUIREMENTS ... 62


35 CHARACTERISTIC AND DESIGN VALUES AND PARTIAL SAFETY ... 63
FACTORS
36 ANALYSIS ... 64
37 LIMIT STATE OF COLLAPSE: FLEXURE ... 64
38 LIMIT STATE OF COLLAPSE: COMPRESSION ... 65
39 LIMIT STATE OF COLLAPSE: SHEAR ... 67
40 LIMIT STATE OF COLLAPSE: TORSION ... 70
41 LIMIT STATE OF SERVICEABILITY: DEFLECTION ... 71
42 LIMIT STATE OF SERVICEABILITY: CRACKING ... 71

ANNEX A SELF COMPACTING CONCRETE ... 72


ANNEX B STRUCTURAL DESIGN (WORKING STRESS METHOD) ... 72
ANNEX C CALCULATION OF DEFLECTION ... 79
ANNEX D SLABS SPANNING IN TWO DIRECTIONS ... 80
ANNEX E EFFECTIVE LEGNTH OF COLUMNS . .. 83
ANNEX F CALCULATION OF CRACK WIDTH ... 86
ANNEX G MOMENTS OF RESISTANCE FOR RECTANGULAR AND . .. 87
T-SECTIONS

LIST OF STANDARDS . .. 88

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 3


. ---
National Building Code Sectional Committee, CED 46

FOREWORD

Section 5 of Part 6 of the Code covers plain and reinforced concrete as also the prestressed concrete. The Section
has been subdivided into the following sub-sections:

5A Plain and Reinforced Concrete


5B Prestressed Concrete
This sub-section 5A covers the structural design aspects of plain and reinforced concrete.
This sub-section 5A was first published in 1970 and was subsequently revised in 1983, to bring it in line with
revised version of IS 456: 1978 on which this chapter was based. Now this revision is intended to bring this
subsection in line with the revised version of IS 456:2000.
This revision incorporates a number of important changes. The major thrust in the revision is on the following lines:

a) In recent years, durability of concrete structures have become the cause of concern to all concrete
technologists. This has led to codify the durability requirements world over. In this revision of the
Code, in order to introduce in-built protection from factors affecting a structure, earlier clause on durability
has been elaborated and a detailed clause covering different aspects of design of durable structure has
been incorporated.
b) Sampling and acceptance criteria for concrete have been revised. With this revision acceptance criteria
has been simplified in line with the provisions given in BS 5328 (Part 4) :1990 ‘Concrete: Part 4
Specification for the procedures to be used in sampling, testing and assessing compliance of concrete’.

Some of the significant changes incorporated in Section 5A (b) areas follows:


a) All the three grades of ordinary Portland cement, namely 33 grade, 43 grade and 53 grade and sulphate
resisting Portland cement have been included in the list of types of cement used (in addition to other
types of cement),
b) The perrrissible limits for solids in water have been modified keeping in view the durability requirements.
c) The clause on admixtures has been modified in view of the availability of new types of admixtures
including superplasticizers.
d) In Table 2 ‘Grades of Concrete’, grades higher than M 40 have been included.
e) It has been recommended that minimum grade of concrete shall be not less than M 20 in reinforced
concrete work (see also 5.1.3).
f) The formula for estimation of modulus of elasticity of concrete has been revised.
?3) In the absence of proper correlation between compacting factor, vee-bee time and slump, workability
has now been specified only in terms of slump in line with the provisions in BS 5328 (Parts 1 to 4).
h) Durability clause has been enlarged to include detailed guidance conced’ng the factors affecting
durability. The table on ‘Environmental Exposure Conditions’ has been modified to include ‘very severe’
and ‘extreme’ exposure conditions. This clause also covers requirements for shape and size of member,
depth of concrete cover, concrete quality, requirement against exposure to aggressive chemical and
sulphate attack, minimum cement requirement and maximum water cement ratio, limits of chloride
content, alkali silica reaction, and importance of compaction, finishing and curing.
j) A clause on ‘Quality Assurance Measures’ has been incorporated to give due emphasis to good practices
of concreting.
k) Proper limits have been introduced on the accuracy of measuring equipments to ensure accurate batching
of concrete.
m) The clause on ‘Construction Joints’ has been modified.
n) The clause on ‘Inspection’ has been modified to give more emphasis on quality assurance.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 5


The significant changes incorporated in Section 5A (c) are as follows:

a) Requirements for ‘Fire Resistance’ have been further detailed.


b) The figure for estimation of modification factor for tension reinforcement used in calculation of basic
values of span to effective depth to control the deflection of flexural member has been modified.
c) Recommendations regarding effective length of cantilever have been added.
d) Recommendations regarding deflection due to lateral loads have been added.
e) Recommendations for adjustments of support moments in restrained slabs have been included.
f) In the determination of effective length of compression members, stability index has been introduced to
determine sway or no sway conditions.
$3) Recommendations have been made for lap length of hooks for”bars in direct tension and flexural tension.
h) Recommendations regarding strength of welds have been modified.
j) Recommendations regarding cover to reinforcement have been modified. Cover has been specified based
on durability requirements for different exposure conditions. The term ‘nominal cover’ has been introduced.
The cover has now been specified based on durability requirement as well as for fire requirements.

The significant change incorporated in Section 5A (d) is the modification of the clause on Walls. The modified
clause includes design of walls against horizontal shear.

In Section 5 on limit state method a new clause has been added for calculation of enhanced shear strength of
sections close to supports. Some modifications have also been made in the clause on Torsion. Formula for
calculation of crack width has been added (separately given in Annex F).

Working stress method has now been given in Annex B so as to give greater emphasis to limit state design. In this
Annex, modifications regarding torsion and enhanced shear strength on the same lines as in Section 5 have been
made.

Whilst the common methods of design and construction have been covered in this Code, special systems of design
and construction of any plain or reinforced concrete structure not covered by this Code may be permitted on
production of satisfactory evidence regarding their adequacy and safety by analysis or test or both (see 18).

In this Code it has been assumed that the design of plain and reinforced cement concrete work is entrusted to a
qualified engineer and that the execution of cement concrete work is carried out under the direction of a qualified
and experience supervisor.

This Section also introduces self-compacting concrete (see Annex A).

In the formulation of this subsection, assistance has been derived from the following publications:

BS 5328 (Part 1) :1991 Concrete: Part 1 Guide to specifying concrete, British Standards Institution
BS 5328 (Part 2) :1991 Concrete: Part 2 Methods for specifying concrete mixes, British Standards Institution
BS 5328 (Part 3) :1990 Concrete: Part 3 Specification for the procedures to be used in producing and
transporting concrete, British Standards Institution
BS 5328 (Part 4) :1990 Concrete: Part 4 Specification for the procedures to be used in sampling, testing and
assessing compliance of concrete, British Standards Institution
BS 8110 (Part 1) :1985 Structural use of concrete: Part 1 Code of practice for design and construction,
British Standards Institution
BS 8110 (Part 2) :1985 Structural use of concrete: Part 2 Code of practice for special circumstances, British
Standards Institution
ACI 318:1995 Building code requirements for reinforced concrete, American Concrete Institute
AS 3600:1988 Concrete structures, Standards Association of Australia
DIN 1045 July 1988 Structural use of concrete, design and construction, Deutsches Institut fur Normung
E.V.
CEB-FIP Model Code 1990, Comite Euro International Du Belon

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

6 NATIONALBUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 5 Concrete: 5A Plain and Reinforced Concrete

SECTION 5A (ftj GENERAL f. - Splitting tensile strength of concrete


f, - Design strength
1 SCOPE
f– Characteristic strength of steel
JY
1.1 This Section deals with the general structural use Hw - Unsupported height of wall
of plain and reinforced concrete.
Hw, - Effective height of wall
1.1.1 For the purpose of this Section, plain concrete z–
ef Effective moment of inertia
structures are those where reinforcement, if provided r- Moment of inertia of the gross section
@
is ignored for determination of strength of the structure. excluding reinforcement
1.2 Design of special requirements of structures, such 1, - Moment of intertia of cracked section
as shells, folded plates, arches, bridges, chimneys, blast K- Stiffness of member
resistant structures, hydraulic structures, liquid k- Constant or coefficient or factor
retaining structures and earthquake resistant structures,
Ld - Development length
shall be done in accordance with good practice
LL - Live load or imposed load
[6-5A(1)].
1- Length of a column or beam between
2 TERMINOLOGY adequate lateral restraints or the
unsupported length of a column
For the purpose of this Section, the definitions given
in accepted standards [6-5A(2)]. 1ef —
Effective span of beam or slab or effective
length of column
3 SYMBOLS 1-
ex Effective length about x-x axis
For the purpose of this standard, the following letter 1- Effective length about y-y axis
ey
symbols shall have the meaning indicated against each; 1, - Clear span, face-to-face of supports
where other symbols are used, they are explained at l’ef - l’~ffor shorter of the two spans at right
the appropriate place: angles
A– Area lx - Length of shorter side of slab
b– Breadth of beam, or shorter dimension of 1- Length of longer side of slab
a rectangular column ;- Distance between points of zero moments
b–Cf Effective width of slab in a beam
b, - Effective width of flange 1, - Span in the direction in which moments
are determined, centre-to-centre of
bw – Breadth of web or rib
supports
D- Overall depth of beam or slab or diameter
12 - Span transverse to 1,, centre-to-centre of
of column; dimension of a rectangular
supports
column in the direction under consideration
1; - lZ for the shorter of the continuous spans
Df – Thickness of flange
M- Bending moment
DL – Dead load
?r– Modular ratio
d– Effective depth of beam or slab
n– Number of samples
d’ – Depth of compression reinforcement from
the highly compressed face P- Axial load on a compression member
E, - Modulus of elasticity of concrete q. - Calculated maximum bearing pressure
EL - Earthquake load %) - Calculated maximum bearing pressure of
soil
E, – Modulus of elasticity of steel
— Eccentricity r- Radius
s– Spacing of stirrups or standard deviation
;Ck - Characteristic cube compressive strength
of concrete T- Torsional moment
Modulus of rupture of concrete (flexural t- Wall thickness
~, -
tensile strength) v- Shear force

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 7


w– Total load j) Low heat Portland cement
WL - Wind load k) Sulphate resisting Portland cement
w– Distributed load per unit area Other combinations of Portland cement with mineral
‘d –
Distributed dead load per unit area admixture (see 4.2) of quality conforming with relevant
~1 –
Distributed imposed load per unit area Indian Standards laid down may also be used in the
.a– Depth of neutral axis manufacture of concrete provided that there are
satisfactory data on their suitability, such as
z– Modulus of section
performance test on concrete containing them.
z– Lever arm
4.1.1 Low heat Portland cement conforming to
a,p – Angle or ratio
accepted standards [6-5A(3)] shall be used with
Y, - Partial safety factor for load
adequate precautions with regard to removal of
Y. - Partial safety factor for material formwork, etc.
dm - Percentage reduction in moment
4.1.2 High alumina cement or supersulphated cement
&–
cc
Creep strain of concrete conforming to accepted standards [6-5A(4)] may be
a–
cbc
Permissible stress in concrete in bending used only under special circumstances with the prior
compression approval of the engineer-in-charge. Specialist literature
Om – Permissible stress in concrete in direct may be consulted for guidance regarding the use of
compression these types of cements.
CJ–
m.
Permissible stress in metal in direct 4.1.3 The attention of the engineer-in-charge and users
compression of cement is drawn to the fact that quality of various
O,c – Permissible stress in steel in compression cements mentioned in 4.1 is to be determined on
6,, – Permissible stress in steel in tension the basis of its conformity to the performance
characteristics given in the respective Indian Standard
6,, – Permissible stress in shear reinforcement
Specification for that cement. Any trade-mark or any
7–
bd
Design bond stress trade name indicating any special features not covered
Tc – Shear stress in concrete in the standard or any qualification or other special
T Maximum shear stress in concrete with performance characteristics sometimes claimed/
c, Inax—
shear reinforcement indicated on the bags or containers or in advertisements
‘r– Nominal shear stress alongside the ‘Statutory Quality Marking’ or otherwise
have no relation whatsoever with the characteristics
d’ - Diameter of bar
guaranteed by the Quality Marking as relevant to that
cement. Consumers are, therefore, advised to go by
SECTION 5A (b) the characteristics as given in the corresponding Indian
MATERIALS, WORKMANSHIP, Standard Specification or seek specialist advise
INSPECTION AND TESTING to avoid any problem in concrete making and
construction.
4 MATERIALS
4.2 Mineral Admixtures
4.1 Cement
4.2.1 Pozzolanas
The cement used shall be any of the following
conforming to accepted standards [6-5A(3)] and the Pozzolanic materials conforming to relevant Indian
type selected should be appropriate for the intended Standards may be used with the permission of the
use: engineer-in-charge, provided uniform blending with
cement is ensured.
a) 33 grade ordinary Portland cement
4.2.LI Fly ash (pulverizedfiel ash)
b) 43 grade ordinary Portland cement
c) 53 grade ordinary Portland cement Fly ash conforming to Grade 1 of accepted standards
d) Rapid hardening Portland cement [6-5A(5)] may be used as part replacement of ordinary
Portland cement provided uniform blending with
e) Portland slag cement
cement is ensured.
f) Portland pozzolana cement (fly ash based)
Portland pozzolana cement (calcined clay 4.2.1.2 Silica @me
g)
based) Silica fume conforming to a standard approved by the
h) Hydrophobic cement deciding authority may be used as part replacement of

8 NATIONAL BUILDING CODE OF INDIA


cement provided uniform blending with the cement is 4.3.3 Size of Aggregate
ensured.
The nominal maximum size of coarse aggregate
NOTE — The silica fume (very fine non-crystalline silicon should be as large as possible within the limits
dioxide) is a by-product of the manufacture of silicon,
specified but in no case greater than one-fourth of
ferrosilicon or the like, from quartz and carbon in electric are
furnace. It is usually used in proportion of 5 to 10 percent of the minimum thickness of the member, provided that
the cement content of a mix. the concrete can be placed without difficulty so as to
surround all reinforcement thoroughly and fill the
4.2.L3 Rice husk ash
corners of the form. For most work, 20 mm aggregate
Rice husk ash giving required performance and is suitable. Where there is no restriction to the flow
uniformity characteristics may be used with the of concrete into sections, 40 mm or larger size may
approval of the deciding authority. be permitted. In concrete elements with thin sections,
NOTE— Rice husk ash is producedby burningrice husk and closely spaced reinforcement or small cover,
containlargeproportionof silica.To achieveamorphousstate, consideration should be given to the use of 10 mm
ricehuskmaybe burntat controlledtemperature.It is necessary nominal maximum size.
to evaluatetheproductfroma particularsource for performance
and uniformity since it can be as deleterious as silt when Plums above 160 mm and up to any reasonable size
incorporated in concrete. Water demand and drying shrinkage may be used in plain concrete workup to a maximum
should be studied before using rice husk.
limit of 20 percent by volume of concrete when
4.2.1.4 A4etakaoline specifically permitted by the engineer-in-charge. The
plums shall be distributed evenly and shall be not closer
Metakaoline having fineness between 700 to
than 150 mm from the surface.
900 m2/kg may be used as pozzolanic material in
concrete. 4.3.3.1 For heavily reinforced concrete members as
NOTE — Metakaoline is obtained by clacination of pure or in the case of ribs of main beams, the nominal
refined kaolintic clay at a temperature between 650”C and maximum size of the aggregate should usually be
850”C, followed by grinding to achieve a fineness of 700 to restricted to 5 mm less than the minimum clear distance
900 m2/kg. The resulting material has high pozzolanicity. between the main bars or 5 mm less than the minimum
4.2.2 Ground Granulated Blast Furnace Slag cover to the reinforcement whichever is smaller.

Ground granulated blast furnace slag obtained by 4.3.4 Coarse and fine aggregate shall be batched
grinding granulated blast furnace slag conforming to separately. All-in-aggregate may be used only where
accepted standards [6-5A(6)] may be used as part specifically permitted by the engineer-in-charge.
replacement of ordinary Portland cements provided
uniform blending with cement is ensured. 4.4 Water

4.3 Aggregates Water use for mixing and curing shall be clean and
free from injurious amounts of oils, acids, alkalis, salts,
Aggregates shall comply with the requirements of sugar, organic materials or other substances that may
accepted standards [6-5A(7)]. As far as possible be deleterious to concrete or steel.
preference shall be given to natural aggregates.
Potable water is generally considered satisfactory
4.3.1 Other types of aggregates such as slag and for mixing concrete. As a guide the following
crushed overbumt brick or tile, which may be found concentrations represent the maximum permissible
suitable with regard to strength, durability of concrete values:
and freedom from harmful effects may be used for plain
concrete members, but such aggregates should not a) To neutralize 100 @ sample of water, using
contain more than 0.5 percent of sulphates as SOg and phenolphthalein as an indicator, it should not
should not absorb more than 10 percent of their own require more than 5 ml of 0.02 normal NaOH.
mass of water. The details of test are given in 7.1 of good
practice [6-5A(8)].
4.3.2 Heavy weight aggregates or light weight
b) To neutralize 100 ml sample of water, using
aggregates such as bloated clay aggregates and sintered
mixed indicator, it should not require more
fly ash aggregates may also be used provided the
engineer-in-charge is satisfied with the data on the than 25 ml of 0.02 normal H2SOd. The details
properties of concrete made with them. of test shall be as given in 7 of good practice
[6-5A(8)].
NOTE — Some of the provisions of the Code would require
modification when these aggregates are used; specialist c) Permissible limits for solids shall be as given
literature may be consulted for guidance. in Table 1.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 9


Table 1 Permissible Limit for Solids suitable for curing concrete. However, water used for
(Clause 4.4) curing should not produce any objectionable stain or
unsightly deposit on the concrete surface. The presence
S1 Tested as per Permissible Limit, of tannic acid or iron compounds is objectionable.
No. Max ~
(1) (2) (3) (4) 4.5 Chemical Admixtures
i) Organic Good practice [6-5A(8)] 200 mgfl 4.5.1 Admixture, if used shall comply with accepted
ii) Inorganic Good practice [6-5A(8)] 3000 mg/1 standards [6-5A( 11)]. Previous experience with and
iii) Sulphates Good practice [6-5A(8)] 400 mg/1
data on such materials should be considered in relation
(as S03)
iv) Chlorides Good practice [6-5A(8)] 2000 mg/1 for to the likely standards of supervision and workmanship
(as Cl) concrete not to the work being specified.
containing embedded
steel and 500 mg/1 for 4.5.2 Admixtures should not impair durability of
reinforced concrete concrete nor combine with the constituent to form
work
v) Suspended Good practice [6-5A(8)] 2000 mg/1
harmful compounds nor increase the risk of corrosion
matter of reinforcement.

4.5.3 The workability, compressive strength and the


4.4.1 In case of doubt regarding development of
slump loss of concrete with and without the use of
strength, the suitability of water for making concrete
admixtures shall be established during the trial mixes
shall be ascertained by the compressive strength and
before use of admixtures.
initial setting time tests specified in 4.4.1.2 and 4.4.1.3.
4.5.4 The relative density of liquid admixtures shall
4.4.1.1 The sample of water taken for testing shall
be checked for each drum containing admixtures and
represent the water proposed to be used for concreting,
compared with the specified value before acceptance.
due account being paid to seasonal variation. The I

sample shall not receive any treatment before testing 4.5.5 The chloride content of admixtures shall be
other than that envisaged in the regular supply of water independently tested for each batch before acceptance.
proposed for use in concrete. The sample shall be stored
4.5.6 If two or more admixtures are used
in a clean container previously rinsed out with similar
simultaneously in the same concrete mix, data should
water.
be obtained to assess their interaction and to ensure
4.4.1.2 Average 28 days compressive strength of at their compatibility.
least three 150 mm concrete cubes prepared with water
proposed to be used shall not be less than 90 percent 4.6 Reinforcement
of the average of strength of three similar concrete The reinforcement shall be any of the following
cubes prepared with distilled water. The cubes shall conforming to the accepted standards [6-5 A(12)]:
be prepared, cured and tested in accordance with good
practice [6-5A(9)]. a) Mild steel and medium tensile steel bars.
b) High strength deformed steel bars.
4.4.1.3 The initial setting time of test block made with
c) Hard-drawn steel wire fabric.
the appropriate cement and the water proposed to be
d) Grade A of structural steel.
used shall not be less than 30 min and shall not differ
by* 30 min from the initial setting time of control test 4.6.1 All reinforcement shall be free from loose mill
block prepared with the same cement and distilled scales, loose rust and coats of paints, oil, mud or any
water. The test blocks shall be prepared and tested in oother substances which ‘may destroy or reduce bond.
accordance with the good practice [6-5 A(1O)]. Sand blasting or other treatment is recommended to
clean reinforcement.
4.4.2 The pH value of water shall be not less than 6.
4.6.2 Special precautions like coating of
4.4.3 Sea Water
reinforcement may be required for reinforced concrete
Mixing or curing of concrete with sea water is not elements in exceptional cases and for rehabilitation
recommended because of presence of harmful salts in of structures. Specialist literature may be referred to
sea water. Under unavoidable circumstances sea water in such cases.
may be used for mixing or curing in plain concrete with
4.6.3 The modulus of elasticity of steel shall be taken
no embedded steel after having given due consideration
as 200 kN/mm2. The characteristic yield strength of
to possible disadvantages and precautions including use
different steel shall be assumed as the minimum yield
of appropriate cement system.
stress/O.2 percent proof stress specified in the relevant
4.4.4 Water found satisfactory for mixing is also Indian Standard.

10 NATIONAL BUILD~G CODE OF INDIA

..
4.7 Storage of Materials characteristic strength of concrete unless there is an
evidence to justify a higher strength for a particular
Storage of materials shall be as described in good
structure due to age.
practice [6-5A(13)].
5.2.1.1 For concrete of grade M 30 and above, the
5 CONCRETE
rate of increase of compressive strength with age shall
5.1 Grades be based on actual investigations.

The concrete shall be in grades designated as per 5.2.1.2 Where members are subjected to lower direct
Table 2. load during construction, they should be checked for
stresses resulting from combination of direct load and
Table 2 Grades of Concrete
bending during construction.
(Clauses 5,1,8 .2.2,14.1,1 and 35.1)
5.2.2 Tensile Strength of Concrete
Group Grade S@fied Characteristic
Des&nation COmpredve Strcmgth of The flexural and splitting tensile strengths shall be
l*mm Cub@at2’Sdaysin obtained in accordance with good practice [6-5 A(14)].
Nhmn2
When the designer wishes to use an estimate of the
(1) (2) (3)
tensile strength from the compressive strength, the
Ordinary M 10 10 following formula may be used:
Concrete M 15 15
M 20 20
Flexural strength, ~r = 0.7 fi N / mm’
Standard M 25 25
Concrete M 30 30 wherefCkis the characteristic cube compressive Strength
M 35 35 of concrete in N/mm2. -
M 40 40
M 45 45 5.2.3 Elastic Deformation
M 50 50
M 55 55 The modulus of elasticity is primarily influenced by
High Strength M 60 60 the elastic properties of the aggregate and to a lesser
Concrete M 65 65 extent by the conditions of curing and age of the
M 70 70
concrete, the mix proportions and the type of cement.
M 75 75
M 80 80 The modulus of elasticity is normally related to the
compressive strength of concrete.
NOTES
1 In the designation of concrete mix M refers to the mix and
5.2.3.1 The modulus of elasticity of concrete can be
the number of the specified compressive strength of 150 mm assumed as follows:
size cube at 28 days, expressed in N/mmz.
2 For concrete of compressive strength greater than M 55, EC=5000&
design parameters given in the standard may not be
applicable and the values may be obtained from specialized where ECis the short-term static modulus of elasticity
literatures and experimental results. in N/mm2.

5.1.1 The characteristic strength is defined as the Actual measured values may differ by &20 percent
strength of material below which not more than 5 from the values obtained from the above expression.
percent of the test results are expected to fall.
5.2.4 Shrinkage
5.1.2 The minimum grade of concrete for plain and
The total shrinkage of concrete depends upon the
reinforced concrete shall be as per Table 5.
constituents of concre~, size of the member and
5.1.3 Concrete of grades lower than those given in environmental conditions. For a given humidity and
Table 5 maybe used for plain concrete constructions, temperature, the total shrinkage of concrete is most
lean concrete, simple foundations, foundation for influenced by the total amount of water present in the
masonry walls and other simple or temporary concrete at the time of mixing and, to a lesser extent,
reinforced concrete construction. by the cement content.

5.2 Properties of Concrete 5.2.4.1 In the absence of test data, the approximate
value of the total shrinkage strain for design may be
5.2.1 Increase of Strength with Age
taken as 0.0003 (for more information, see accepted
There is normally a gain of strength beyond 28 days. standard [6-5 A(15)] ).
The quantum of increase depends upon the grade
5.2.5 Creep of Concrete
and type of cement, curing and environmental
conditions, etc. The design should be based on 28 days Creep of concrete depends, in addition to the factors

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 11


listed in 5.2.4, on the stress in the concrete, age at (1) (2) (3)
loading and the duration of loading. As long as the
stress in concrete does not exceed one-third of its beams, walls, columns; Floors;
characteristic compressive strength, creep may be Hand placed pavements; Canal
assumed to be proportional to the stress. lining; Strip footings
Heavily reinforced sections in Medium 50-100
5.2.5.1 In the absence of experimental data and
slabs, beams, walls, columns
detailed information on the effect of the variables, the
Slipform work; Pumped Medium 75-1oo
ultimate creep strain may be estimated from the
concrete
following values of creep coefficient (that is, ultimate
creep strain/elastic strain at the age of loading); for Trench fill; in-situ piling High 100-150
long span structure, it is advisable to determine actual Tremie concrete Very high See 6.1.2
creep strain, likely to take place:
NOTE — For most of the placing conditions, internal vibrators
(needle vibrators) are suitable. The diameter of the needIe
Age at Loading Creep Coefficient shall be determined based on the density and spacing of
7 days 2.2 reinforcement bars an thickness of sections. For tremie
concrete, vibrators are not required to be used (see
28 days 1.6 also 13.3).
1 year 1.1
6.1.1 In the ‘very low’ category of workability where
NOTE — The ultimate creep strain, estimated as described strict control is necessary, for example, pavement
above does not include the elastic strain.
quality concrete, measurement of workability by
5.2.6 Thermal Expansion determination of compacting factor will be more
appropriate than slump (see accepted standard
The coefficient of thermal expansion depends on nature
[6-5A(16)]) and a value of compacting factor of 0.75
of cement, the aggregate, the cement content, the to 0.80 is suggested.
relative humidity and the size of sections.
6.1.2 In the ‘very high’ category of workability,
The value of coefficient of thermal expansion for
measurement of workability by determination of flow
concrete with different aggregates may be taken as will be appropriate (see accepted standard [6-5A(17)] ).
below:
7 DURABILITY OF CONCRETE
Type of Aggregate Coefficient of Thermal
7.1 General
Expansion for ConcretePC
Quartzite 1.2 to 1.3 to 10-5 A durable concrete is one that performs satisfactorily
Sandstone 0.9to 1.2 to 10-5 in the working environment during its anticipated
Granite 0.7to 0.95to 10-5 exposure conditions during service. The materials and
Basalt 0.8 to 0.95 to 10-5 mix proportions specified and used should be such as
to maintain its integrity and, if applicable, to protect
Limestone 0.6 to 0.9 to 10-5
embedded metal from corrosion.

6 WORKABILITY OF CONCRETE 7.1.1 One of the main characteristics influencing the


durability of concrete is its permeability to the ingress
6.1 The concrete mix proportions chosen should be such
of water, oxygen, carbon dioxide, chloride, sulphate and
that the concrete is of adequate workability for the
other potentially deleterious substances. Impermeability
placing conditions of the concrete and can properly be
is governed by the constituats and workmanship used
compacted with the means available. Suggested ranges
in making the concrete. With normal-weight aggregates
of workability of concrete measured in accordance with
a suitably low permeability is achieved by having an
good practice [6-5 A(16)] are given below:
adequate cement content, sufficiently low free waterl
cement ratio, by ensuring complete compaction of the
Placing Conditions Degree of Slump
concrete, and by adequate curing.
Workability mm
(1) (2) (3) The factors influencing durability include:

Blinding concrete; Shallow Very low See 6.1.1 a) the environment;


sections; Pavements using b) the cover to embedded steel;
pavers c) the type and quality of constituent materials;
Mass concrete; Lightly Low 25-75 d) the cement content and water/cement ratio of
reinforced sections in slabs, the concrete;

12 NATIONAL BUILDING CODE OF INDIA


e‘) workmanship, to obtain full compaction and 7.2.2 Exposure Conditions
efficient curing; and
7.2.2.1 General environment
f) the shape and size of the member.
The general environment to which the concrete will
The degree of exposure anticipated for the concrete
be exposed during its working life is classified into
during its service life together with other relevant
five levels of severity, that is, mild, moderate, severe,
factors relating to mix composition, workmanship,
very severe and extreme as described in Table 3.
design and detailing should be considered. The
concrete mix to provide adequate durability under these 7.2.2.2 Abrasive
conditions should be chosen taking account of the
Specialist literatures may be referred to for durability
accuracy of current testing regimes for control and
requirements of concrete surfaces exposed to abrasive
compliance as described in this Section.
action, for example, in case of machinery and metal
tyres.
7.2 Requirements for Durability
7.2.2.3 Freezing and thawing
7.2.1 Shape and Size of Member
Where freezing and thawing actions under wet
The shape or design details of exposed structures
should be such as to promote good drainage of water conditions exist, enhanced durability can be obtained
by the use of suitable air entraining admixtures. When
and to avoid standing pools and rundown of water.
concrete lower than grade M 50 is used under these
Care should also be taken to minimize any cracks that
may collect or transmit water. Adequate curing is conditions, the mean total air content by volume of
the fresh concrete at the time of delivery into the
essential to avoid the harmful effects of early loss of
construction should be:
moisture (see 12.5). Member profiles and their
intersections with other members shall be designed and
Nominal Maximum Size Entrained Air
detailed in a way to ensure easy flow of concrete and
Aggregate (mm) Percentage
proper compaction during concreting.
20 5&~
Concrete is more vulnerable to deterioration due to
40 4*1
chemi CA or climatic attack when it is in thin sections,
in sections under hydrostatic pressure from one side
Since air entrainment reduces the strength, suitable
only, in partially immersed sections and at comers and
adjustments may be made in the mix design for
edges of elements. The life of the structure can be
achieving required strength.
lengthened by providing extra cover to steel, by
chamfering the corners or by using circular cross- 7.2.2.4 Exposure to sulphate attack
sections or by using surface coatings which prevent or
Table 4 gives recommendations for the type of cement,
reduce the ingress of water, carbon dioxide or
maximum free water/cement ratio and minimum
aggressive chemicals.
cement content, which are required at different sulphate

Table 3 Environmental Exposure Conditions


(Clauses 7.2.2.1 and 34.3.2)

S1 No. Environment Exposure Conditions

(1) (2) (3)

i) Mild Concrete surfaces protected against weather or aggressive conditions, except those situated in coastal
area.
ii) Moderate Concrete surfaces sheltered from severe rain or freezing whilst wet.
Concrete exposed to condensation and rain.
Concrete continuously under water.
Concrete in contact or buried under non-aggressive soil/ground water.
Concrete surfaces sheltered from saturated salt air in coastal area.
}
iii) Severe Concrete surfaces exposed to severe rain, alternate wetting and drying or occasional freezing whilst wet
or severe condensation.
Concrete completely immersed in sea water.
Concrete exposed to coastal environment.
iv) Very Severe Concrete surfaces exposed to sea water spray, corrosive fumes or severe freezing conditkms whilst wet.
Concrete in contact with or buried under aggressive sub-soil/ground water.
v) Extreme Surface of members in tidal zone.
Members in direct contact with liquid/solid aggressive chemicals.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 13

..
Table 4 Requirements for Coucrete Exposed to Sulphate Attack
(Clauses 7.2.2.4 and 8.1.2)

S1 Class Concentration of Sulphates, Type of Cement Dense, Fully Compacted


No. Expressed as SOS Concrete. Made with 20 mm
/
A
Y
Nominal Maximum Size
In Soil In Ground Aggregates in Accordance
c A \ Water with Accepted Standard
Total S03 so, its2:1 [6-5A(18)]
Water Soit
Extract Minimum MaximumFree
Percent CementContent Water-Cement
M N
kg/m3 Ratio
(1) (2) (3) (4) (5) (6) (7) (8)

O 1 Traces Less Less Ordkxwy Portland cement or Portland slag 280 0.55
(<0.2) than 1.0 than 0.3 cement or Portland pozzolana cement
ii) 2 0.2 to 0.5 l.oto 1.9 0.3 to 1,2 Ordiuary Porttand cement or Portland slag 330 0.50
cement or Portland pozzolana cement
Supersulphated cement or sulphate resisting 310 0.50
Porttand cement
iii) 3 0.5 to 1.0 1.9 to 3.1 1.2 to 2.5 Supersulphated cement or sulphate resisting 330 0.50
Portland cement
Portland pozzolana cement or Portland slag 350 0.45
cement
iv) 4 1.0 to 2.0 3.1 to 5.0 2.5 to 5.0 Supersulphatcd or sulphatc resisting Portland 370 0.45
cement

v) 5 More More More .%dphate resisting Pordarrd cement or 400 0.40


than 2.0 than 5.0 than 5.0 srspersulphatedcement with protectivecoatings

NOTES
1 Cement content given in this table is irrespective of grades of cement.
2 Use of supersulphated cement is generally restricted where the prevailing temperature is above 40”C.
3 Supersulphatedcement gives an acceptable life provided that the concrete is dense and prepared with a water-cement ratio of 0.4
or less, in minerat acids, down to pH 3.5.
4 The cement contents giveninCO16 of this table are the minimum recommended. For S03 contents near the upper limit of any class,
cement contents above these minimum are advised.
5 For severe conditions, such as thii sections nnder hydrostatic pressure on one side only and sections partly immersed, consideration
should be given to a further rednction of water-cement ratio.
6 Portland slag cement conforming to accepted standard [6-5A(3)] with slag content more than 50 percent exhibits better aulphate
resisting properties.
7 Where chloride is encountered along with sulphates in soil or ground water, ordinary Portland cement with C3A content from 5
to 8 percent shall be desirable to be nsed in concrete, instead of sulphate resisting cement, Alternatively, Portland slag cement
conforming to accepted standard [6-5A(3)] having more than 50 percent slag or a blend of ordhary Portt~d cement ad slag ~Y be
used provided sufficient information is available on performance of such blended cements M these conditions.

concentrations in near-neutral ground water having pH 7.2.3.2 The nominal coyer to the reinforcement shall
of 6 to 9. be provided as per 25.4;
For the very high sulphate concentrations in Class 5
7.2.4 Concrete Mix Proportions
conditions, some form of lining such as polyethylene
or polychloroprene sheet; or surface coating based on 7.2.4.1 General
asphalt, chlorinated rubber, epoxy; or polyurethane
The free water-cement ratio is an important factor in
materials should also be used to prevent access by the
governing the durability of concrete and should always
sulphate solution.
be the lowest value. Appropriate values for minimum
7.2.3 Requirement of Concrete Cover cement content and the maximum free water-cement
7.2.3.1 The protection of the steel in concrete against ratio are given in Table 5 for different exposure
corrosion depends upon au adequate thickness of good conditions. The minimum cement content and
quality concrete. maximum water-cement ratio apply to 20 mm nominal

14 NATIONAL BUILDING CODE OF INDIA


Table 5 Minimum Cement Content, Maximum Water-Cement Ratio and Minimum Grade
of Concrete for Different Exposures with Normal Weight Aggregates of 20 mm
Nominal Maximum Size
(Clauses 5.1.2,5 .1.3,7.2.4.1 and 8.1.2)

S1No. Exposure Plain Concrete Reinforced Concrete


& 3/ 4 3
/
Minimum Maximum Free Minimum Grade Minimum Maximum Free Minimum Grade
Cement Content Water-Cement of Concrete Cement Content Water-Cement of Concrete
kg/m3 Ratio kg/m3 Ratio
(1) (2) (3) (4) (5) (6) (7) (8)

i) Mild 220 0.60 . 300 0.55 M 20


ii) Moderate 240 0.60 M 15 300 0.50 M 25
iii) Severe 250 0.50 M 20 320 0,45 M 30
iv) Very Severe 260 0.45 M 20 340 0.45 M 35
v) Extreme 280 0.40 M 25 360 0.40 M 40

NOTES
1 Cement content prescribed in this table is irrespective of the grades of cement and it is inclusive of additions mentioned in 4.2. The
additions such as fly ash or ground granulated blast furnace slag may be taken into account in the concrete composition with respect
to the cement content and water-cement ratio if the suitability is established and as long as the maximum amounts taken into account
do not exceed the limit of pozzolana and slag specified in accordance with accepted standard [6-5A(19)].
2 Minimum grade for plain concrete under mild exposure condition is not specified.

maximum size aggregate. For other sizes of aggregate higher the chloride content, or if subsequently exposed
they should be changed as given in Table 6. to warm moist conditions, the greater the risk of
corrosion. All constituents may contain chlorides and
Table 6 Adjustments to Minimum Cement concrete may be contaminated by chlorides from the
Contents for Aggregates Other Than 20 mm external environment. To minimize the chances of
Nominal Maximum Size deterioration of concrete from harmful chemical salts,
(Clause 7.2.4.1) the levels of such harmful salts in concrete coming
from concrete materials, that is, cement, aggregates
S1 Nominal Maximum Adjustments to Minimum Cement water and admixtures, as well as by diffusion from the
No. Aggregate Size Contents Given in Table 5
environment should be limited. The total amount of
mm kglm3
chloride content (as Cl) in the concrete at the time of
(1) (2) (3)
placing shall be as given in Table 7.
i) 10 +40
ii) 20 0 The total acid soluble chloride content should be
iii) 40 -30 calculated from the mix proportions and the measured
chloride contents of each of the constituents. Wherever
7.2.4.2 Maximum cement content possible, the total chloride content of the concrete
should be determined.
Cement content not including fly ash and ground
granulated blast furnace slag in excess of 450 kg/m3
Table 7 Limits of Chloride Content of Concrete
should not be used unless special consideration has
(Clause 7.2.5.2)
been given in design to the increased risk of cracking
due to drying shrinkage in thin sections, or to early S1 Type or Use of Concrete Maximum Total Acid
thermal cracking and to the increased risk of damage No. Soluble Chloride
due to alkali silica reactions. Content Expressed as
kg/m3 of Concrete
7.2.5 Mix Constituents (1) (2) (3)

7.2.5.1 General i) Concrete containing metal and 0.4


steam cured at elevated
For concrete to be durable, careful selection of the mix temperature and prestressed
and materials is necessary, so that deleterious concrete
ii) Reinforced concrete or plain 0.6
constituents do not exceed the limits.
concrete containing embedded
7.2.5.2 Chlorides in concrete metal
iii) Concrete not containing 3.0
Whenever there is chloride in concrete there is an embedded metal or any material
requiring protection from chloride
increased risk of corrosion of embedded metal. The

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 15

..
7.2.5.3 Sulphates in concrete d) Limiting the cement content in the concrete
mix and thereby limiting total alkali content
Sulphates are present in most cements and in some
in the concrete mix. For more guidance
aggregates; excessive amounts of water-soluble
specialist literatures may be referred.
sulphate from these or other mix constituents can cause
expansion and disruption of concrete. To prevent this, 7.2.6 Concrete in Aggressive Soils and Water
the total water-soluble sulphate content of the concrete
7.2.6.1 General
mix, expressed as SO~l should not exceed 4 percent by
mass of the cement in the mix. The sulphate content The destructive action of aggressive waters on concrete
should be calculated as the total from the various is progressive. The rate of deterioration decreases as
constituents of the mix. the concrete is made stronger and more impermeable,
and increases as the salt content of the water increases.
The 4 percent limit does not apply to concrete made Where structures are only partially immersed or are in
with supersulphated cement complying with accepted contact with aggressive soils or waters on one side only,
standard [6-5 A(20)]. evaporation may cause serious concentrations of salts
7.2.5.4 Alkali-aggregate reaction with subsequent deterioration, even where the original
salt content of the soil or water is not high.
Some aggregates containing particular varieties of
NOTE — Guidance regarding requirements for concrete
silica may be susceptible to attack by alkalis (NazO
exposed to sulphate attack is given in 7.2.2.4.
and K20) originating from cement or other sources,
producing an expansive reaction which can cause 7.2.6.2 Drainage
cracking and disruption of concrete. Damage to @
At sites where alkali concentrations are high or may
concrete from this reaction will normally only occur become very high, the ground water should be lowered
when all the following are present together: by drainage so that it will not come into direct contact
a) A high moisture level, within the concrete; with the concrete,

b) A cement with high alkali content, or another Additional protection may be obtained by the use of
source of alkali; and chemically resistant stone facing or a layer of plaster
c) Aggregate containing an alkali reactive of Paris covered with suitable fabric, such as jute
constituent. thoroughly impregnated with bituminous material.

Where the service records of particular cement/ 7.2.7 Compaction, Finishing and Curing
aggregate combination are well established, and do not
Adequate compaction without segregation should be
include any instances of cracking due to alkali-
ensured by providing suitable workability and by
aggregate reaction, no further precautions should be
employing appropriate placing and compacting
necessary. When the materials are unfamiliar,
equipment and procedures. Full compaction is
precautions should take one or more of the following
particularly important in the vicinity of construction
form:
and movement joints and of embedded water bars and
a) Use of non-reactive aggregate from alternate reinforcement.
sources.
Good finishing practices are essential for durable
b) Use of low alkali ordinary Portland cement concrete.
having total alkali content not more than 0.6
percent (as Na,O equivalent). Overworking the surface and the addition of waterl
cement to aid in finishing should be avoided; the
Further advantage can be obtained by use of
resulting laitance will have impaired strength and
fly ash (Grade 1) conforming to accepted
durability and will be particularly vulnerable to
standard [6-5A(5)] or granulated blastfurnace
freezing and thawing under wet conditions.
slag conforming to accepted standard
[6-5A(5)] as part replacement of ordinary It is essential to use proper and adequate curing
Portland cement (having total alkali techniques to reduce the permeability of the concrete
content as Na20 equivalent not more than and enhance its durability by extending the hydration
0.6 percent), provided fly ash content is at of the cement, particularly in its surface zone (see 12.5).
least 20 percent or slag cement is at least
7.2.8 Concrete in Sea-water
50 percent.
c) Measures to reduce the degree of saturation Concrete in sea-water or exposed directly along the
of the concrete during service, such as use of sea-coast shall be at least M 20 Grade in the case of
impermeable membranes. plain concrete and M 30 in case of reinforced concrete.

16 NATIONAL BUILDING CODE OF INDIA


The use of slag or pozzolana cement is advantageous b) Grade designation;
under such conditions. c) Type of cement;
7.2.8.1 Special attention shall be given to the design d) Maximum nominal size of aggregate;
of the mix to obtain the densest possible concrete; slag, e) Minimum cement content (for design mix
broken brick, soft limestone, soft sandstone, or other concrete);
porous or weak aggregates shall not be used. f) Maximum water-cement ratio;
7.2.8.2 As far as possible, preference shall be given g) Workability;
to precast members unreinforced, well-cured and h) Mix proportion (for nominal mix concrete);
hardened, without sharp corners, and having trowel- j) Exposure conditions as per Tables 4 and 5;
smooth finished surfaces free from crazing, cracks or k) Maximum temperature of concrete at the time
other defects; plastering should be avoided. of placing;
7.2.8.3 No construction joints shall be allowed within m) Method of placing; and
600 mm below low water-level or within 600 mm of n) Degree of supervision.
the upper and lower planes of wave action. Where
8.1.2.1 In appropriate circumstances, the following
unusually severe conditions or abrasion are anticipated,
such parts of the work shall be protected by bituminous additional information may be specified;
or silico-flouride coatings or stone facing bedded with a) Type of aggregate,
bitumen. b) Maximum cement content, and
7.2.8.4 In reinforced concrete structures, care shall be c) Whether an admixture shall or shall not be
taken to protect the reinforcement from exposure to used and the type of admixture and the
saline atmosphere during storage, fabrication and use. condition of use.
It may be achieved by treating the surface of
8.2 Design Mix Concrete
reinforcement with cement wash or by suitable
methods. 8.2.1 As the guarantor of quality of concrete used in
the construction, the constructor shall carry out the mix
8 CONCRETE MIX PROPORTIONING design and the mix so designed (not the method of
8.1 Mix Proportion design) shall be approved by the employer within the
limitations of parameters and other stipulations laid
The mix proportion shall be selected to ensure the down by this standard.
workability of the fresh concrete and when concrete is
hardened, it shall have the required strength, durability 8.2.2 The mix shall be designed to produce the grade
and surface finish. of concrete having the required workability and a
characteristic strength not less than appropriate values
8.1.1 The determination of the proportions of cement, given in Table 2. The target mean strength of concrete
aggregates and water to attain the required strengths mix should be equal to the characteristic strength plus
shall be made as follows: 1.65 times the standard deviation.
a) By designing the concrete mix; such concrete 8.2.3 Mix design done earlier not prior to one year
shall be called ‘Design mix concrete’, or may be considered adequate for later work provided
b) By adopting nominal concrete mix; such there is no change in source and the quality of the
concrete shall be called ‘Nominal mix materials.
concrete’.
8.2.4 Standard Deviation
Design mix concrete is preferred to nominal mix. If
The standard deviation for each grade of concrete shall
design mix concrete cannot be used for any reason on
be calculated, separately.
the work for grades of M 20 or lower, nominal mixes
may be used with the permission of engineer-in-charge, 8.2.4.1 Standard deviation based on test strength of
which, however, is likely to involve a higher cement sample
content.
a) Number of test results of samples — The total
8.1.2 Information Required number of test strength of samples required
to constitute an acceptable record for
In specifying a particular grade of concrete, the
calculation of standard deviation shall be not
following information shall be included:
less than 30. Attempts should be made to
a) Type of mix, that is, design mix concrete or obtain the 30 samples, as early as possible,
nominal mix concrete; when a mix is used for the first time.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 17


b) In case of significant changes in concrete — 9 PRODUCTION OF CONCRETE
When significant changes are made in the
9.1 Quality Assurance Measures
production of concrete batches (for example
changes in the materials used, mix design, 9.1.1 In order that the properties of the completed
equipment or technical control), the standard structure be consistent with the requirements and the
deviation value shall be separately calculated assumptions made during the planning and the design,
for such batches of concrete. adequate quality assurance measures shall be taken.
c) Standard deviation to be brought up to date The construction should result in satisfactory strength,
— The calculation of the standard deviation serviceability and long-term durability so as to lower
shall be brought up to date after every change the overall life-cycle cost. Quality assurance in
of mix design. construction activity relates to proper design, use of
adequate materials and components to be supplied by
8.2.4.2 Assumed standard deviation the producers, proper workmanship in the execution
Where sufficient test results for a particular grade of of works by the contractor and ultimately proper
concrete are not available, the value of standard care during the use of structure including timely
deviation given in Table 8 may be assumed for design maintenance and repair by the owner.
of mix in the first instance. As soon as the results of 9.1.2 Quality assurance measures are both technical 8
samples are available, actual calculated standard and organizational. Some common cases should be
deviation shall be used and the mix designed properly. specified in a general Quality Assurance Plan which
However, when adequate past records for a similar shall identify the key elements necessary to provide
grade exist and justify to the designer a value of fitness of the structure and the means by which they
standard deviation different from that shown in Table are to be provided and measured with the overall
8, it shall be permissible to use that value. purpose to provide confidence that the realized project
will work satisfactorily in service fulfilling intended
Table 8 Assumed Standard Deviation
needs. The job of quality control and quality assurance
(Clause 8.2.4.2 and Table 11)
would involve quality audit of both the inputs as well
Grade of Concrete Assumed Standard Deviation as the outputs. Inputs are in the form of materials for
Nhnm2 concrete; workmanship in all stages of batching,
(1) (2) mixing, transportation, placing, compaction and
curing; and the related plant, machinery and
M 10
M 15 1 3.5
equipments; resulting in the output in the form of
concrete in place. To ensure proper performance, it is
M 20
M 25
M 30
1 4.0
necessary that each step in concreting which will be
covered by the next step is inspected as the work
M 35 proceeds (see also 16).
M 40 5,0
M 45 9.1.3 Each party involved in the realization of a project
M 50 ) should establish and implement a Quality Assurance
NOTE — The above values correspond to the site control Plan, for its participation in the project. Supplier’s and
having proper storage of cement; weigh batching of all subcontractor’s activities shall be covered in the plan.
materials; controlled addition of water; regular checking of all The individual Quality Assurance Plans shall fit into
materials, aggregate gradings and moisture content; and
the general Quality Assurance Plan. A Quality
periodical checking of workability and strength. Where there
is deviation from the above the values given in the above table Assurance Plan shall define the tasks and responsibilities
shall be increased by 1 N/mrn2. of all persons involved, adequate control and checking
procedures, and the organization and maintaining
8.3 Nominal Mix Concrete adequate documentation of the building process and
its results. Such documentation should generally
Nominal mix concrete may be used for concrete of M 20
include:
or lower. The proportions of materials for nominal mix
concrete shall be in accordance with Table 9. a) test reports and manufacturer’s certificate for
materials, concrete mix design details;
8.3.1 The cement content of the mix specified in
b) pour cards for site organization and clearance
Table 9 for any nominal mix shall be proportionately
for concrete placement;
increased if the quantity of water in a mix has to be
increased to overcome the difficulties of placement and c) record of site inspection of workmanship,
compaction, so that the water-cement ratio as specified field tests;
is not exceeded. d) non-conformance reports, change orders;

18 NATIONAL BUILDING CODE OF INDIA

.-
... ,.,, -%
.

Table 9 Proportions for Nominal Mix Concrete


(Clauses 8.3 and 8.3.1)

Grade of’ Total Quantity of Dry Aggregates by Proportion of Fine Aggregate to Quantity of Water per
Concrete Mass per 50 kg of Cement, to be Coarse Aggregate 50 kg of Cement,
Taken as the Sum of the Individual (by Mass) Max
Masses of Fine and Coarse
Aggregates, kg,
Max
(1) (~) (3) (4)

.M 5 800 Generally 1:2 but subject to an upper 60


M 7.5 625 limit of 1: 1Y2and a lower limit of 1:2Y2 45
M 10 480 34
M15 330 32
M 20 250 30

NOTE — The proportion of the fine to coarse aggregates should he adjusted from upper limit to lower limit progressively as the
grading of fine aggregates becomes finer and the maximum size of coarse aggregate becomes larger. Graded coarse aggregate shall be b

used.

Example

For an average grading of fine aggregate (that is, Zone 11 of Table 4 of IS 383), the proportions shall be 1:1?/2, 1:2 and 1:2?/2 for
maximum size of aggregates 1() mm, 20 mm and 40 mm respective] y.

e) quaiity control charts; and be checked as frequently as possible, the frequency


f) statistical analysis. for a given job being determined by the engineer-in-
charge to ensure that the specified grading is
N(3TE -– Quality confrol charts are recommended
wherever the concrete is in continuous production over maintained.
considerable period.
9.2.2 The accuracy of the measuring equipment shall
9.Z Batching be within* 2 percent of the quantity of cement being
measured and within & 3 percent of the quantity of
To avoid confusion and error in batching, consideration
aggregate, admixtures and water being measured.
should be given to using the smallest practical number
of different concrete mixes on any site or in any one 9.2.3 Proportion/Type and grading of aggregates shall
plant. In batching concrete, the quantity of both cement be made by trial in such a way so as to obtain densest
and aggregate shall be determined by mass; admixture, possible concrete. All ingredients of the concrete
if solicl, by mass; liquid admixture may, however, be should be used by mass only.
measured in volume or mass; water shall be weighed
9.2.4 Volume batching may be allowed only where
or measured by volume in a calibrated tank (see also
weigh-batching is not practical and provided accurate
accepted standard [6-5A(21 ) I ).
bulk densities of materials to be actually used in
Ready-mixed concrete supplied by ready-mixed concrete have earlier been established. Allowance for
concrete plant shall be preferred. For large and medium bulking shall be made in accordance with accepted
project sites the concrete shall be sourced from ready- sfandard [6-5 A(23)]. The mass volume relationship
mixcd concrete plants or from on site or off site should be checked as frequently as necessary, the
batching and mixing plants (see also accepted standard frequency for the given job being determined by
[6-5 A(21)] ). engineer-in-charge to ensure that the specified grading
is maintained.
9.2.1 Except where it can be shown to the satisfaction
of the engineer-in-charge that supply of properly 9.2.5 It is important to maintain the water-cement ratio
graded aggregate of uniform quality can be maintained constant at its correct value. To this end, determination
over a period of work, the grading of aggregate should of moisture contents in both fine and coarse aggregates
be controlled by obtaining the coarse aggregate in shall be made as frequently as possible, the frequency
different sizes and blending them in the right for a given job being determined by the engineer-in-
proportions when required, the different sizes being charge according to weather conditions. The amount
stocked in separate stock-piles. The material should of the added water shall be adjusted to compensate for
be stock-piled for several hours preferably a day before any observed variations in the moisture contents. For
use. The grading of coarse and fine aggregate should the determination of moisture content in the aggregates,

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 19


accepted standard [6-5 A(23)] may be referred to. To to remain sufficiently rigid during placing and
allow for the variation in mass of aggregate due to compaction of concrete and shall be such as to prevent
variation in their moisture content, suitable adjustments loss of slurry from the concrete. For further details
in the masses of aggregates shall also be made. In the regarding design, detailing, etc, reference maybe made
absence of exact data, only in the case of nominal to good practice [6-5 A(25)]. The tolerances on the
mixes, the amount of surface water may be estimated shapes, lines and dimensions shown in the drawing
from the values given in Table 10. shall be within the limits given below:

Table 10 Surface Water Carried by Aggregate a) Deviation from


specified dimensions +12
(Clause 9.2.5)
of cross-section of –6-
sl Ag~ate Approximate Quantity colwims and beams
No. of Surface Water
c
A
\ b) Deviation from
Percentby t/m2 dimensions of
Mass footings
(1) (2) (3) (4)
1) Dimensions +50m
i) Very wet sand 7.5 120 in plan –12
ii) Moderately wet sand 5.0 80
iii) Moist sand 2.5 40
2) Eccentricity 0.02 times the width
iv) Moist gravel or croshed rock’) 1.25 -2.5 20-40 of the footing in the
direction of deviation
1)Coarser the aggregate,less the water it will carry. but not more than
50 mm
9.2.6 No substitutions in materials used on the work
or alterations in the established proportions, except as 3) Thickness * 0.05 times the
specified thickness
permitted in 9.2.4 and 9.2.5 shall be made without
additional tests to show that the quality and strength These tolerances apply to concrete dimensions only,
of concrete are satisfactory. and not to positioning of vertical reinforcing steel or
9.3 Mixing dowels.

Concrete shall be mixed in a mechanical mixer. The 10.2 Cleaning and Treatment of Formwork
mixer should comply with accepted standard
[6-5 A(24)]. The mixers shall be fitted with water All rubbish, particularly, chippings, shavings and
measuring (metering) devices. The mixing shall be sawdust shall be removed from the interior of the forms
continued until there is a uniform distribution of the before the concrete is placed. The face of formwork in
materials and the mass is uniform in colour and contact with the concrete shall be cleaned and treated
consistency. If there is segregation after unloading from with form release agent. Release agents should be
the mixer, the concrete should be re-mixed. applied so as to provide a thin uniform coating to the
forms without coating the reinforcement.
9.3.,1 For guidance, the mixing time shall beat least 2
min. For other types of more efficient mixers, 10.3 Stripping Time
manufacturers recommendations shall be followed; for
Forms shall not be released until the concrete has
hydrophobic cement it maybe decided by the engineer-
in-charge. achieved a strength of at least twice the stress to which
the concrete may be subjected at the time of removal
9.3.2 Workability should be checked at frequent of formwork. The strength referred to shall be that of
intervals (see accepted standard [6-5A(16)] ). concrete using the same ‘cement and aggregates and
9.3.3 Dosages of retarders, plasticizers and admixture, if any, with the same proportions and cured
superplasticizers shall be restricted to 0.5, 1.0 and 2.0 under conditions of temperature and moisture similar
percent respectively by weight of cementitious to those existing on the work.
materials, unless a higher value is agreed upon between
10.3.1 While the above criteria of strength shall be
the manufacturer and the constructor based on
the guiding factor for removal of formwork, in normal
performance test.
circumstances where ambient temperature does not
10 FORMWORK fall below 15°C and where ordinary Portland cement
is used and adequate curing is done, following striking
10.1 General period may deem to satisfy the guideline given
The formwork shall be designed and constructed so as in 10.3:

20 NATIONAL BUILDING CODE OF INDIA


Type of Formwork Minimum Period be avoided. Reinforcement should be secured against
Before Striking displacement outside the specified limits.
Formwork 11.3.1 Tolerances on Placing of Reinforcement
a) Vertical formwork to 16-24 h
columns, walls, beams Unless otherwise specified by engineer-in-charge, the
reinforcement shall be placed within the following
b) Soffit forrnwork to slabs 3 days
tolerances:
(Props to be refixed
immediately after removal a) for effective depth 200 mm or less *lomm
of formwork) b) for effective depth more than 200 mm + 15 mm
c) Soffit formwork to beams 7 days
12.3.2 Tolerance for Cover
(Props to be refixed
immediately after removal Unless specified otherwise, actual concrete cover
of formwork) should not deviate from the required nominal cover
d) Props to slabs:
1) Spanning up to 4,5 m 7 days
2) Spanning over 4.5 m 14 days Nominal cover as given in 25.4.1 should be specified
e) Props to beams and to all steel reinforcement including links. Spacers
arches: between the links (or the bars where no links exist)
1) Spanning up to 6 m 14 days and the formwork should be of the same nominal size
2) Spanning over 6 m 21 days as the nominal cover.

Spacers, chairs and other supports detailed on


For other cements and lower temperature, the stripping
drawings, together with such other supports as maybe
time recommended above may be suitably modified.
necessary, should be used to maintain the specified
10.3.2 The number of props left under, their sizes and nominal cover to the steel reinforcement. Spacers or
disposition shall be such as to be able to safely carry chairs should be placed at a maximum spacing of 1 m
the full dead load of the slab, beam or arch as the case and closer spacing may sometimes be necessary.
may be together with any live load likely to occur
Spacers, cover blocks should be of concrete of same
during curing or further construction.
strength or PVC.
10.3.3 Where the shape of the element is such that the
11.4 Welded Joints or Mechanical Connections
formwork has re-entrant angles, the formwork shall
be removed as soon as possible after the concrete has Welded joints or mechanical connections in
set, to avoid shrinkage cracking occurring due to the reinforcement may be used but in all cases of important
restraint imposed. connections, test shall be made to prove that the joints
are of the full strength of bars connected. Welding of
11 ASSEMBLY OF REINFORCEMENT
reinforcements shall be done in accordance with good
11.1 Reinforcement shall be bent and fixed in practice [6-5A(27)].
accordance with procedure specified in good practice
11.5 Where reinforcement bars up to 12 mm for high
[6-5 A(26)]. The high strength deformed steel bars
strength deformed steel bars and up to 16 mm for mild
should not be re-bent or straightened without the
steel bars are bent aside at construction joints and
approval of engineer-in-charge.
afterwards bent back into their original positions, care
Bar bending schedules shall be prepared for all should be taken to ensure that at no time is the radius
reinforcement work. of the bend less than 4 bar $iameters for plain mild
steel or 6 bar diameters for deformed bars. Care shall
11.2 All reinforcement shall be placed and maintained
also be taken when bending back bars, to ensure that
in the position shown in the drawings by providing
the concrete around the bar is not damaged beyond
proper cover blocks, spacers, supporting bars, etc.
the band.
11.2.1 Crossing bars should not be tack-welded for
11.6 Reinforcement should be placed and tied in such
assembly of reinforcement unless permitted by
a way that concrete placement be possible without
engineer-in-charge.
segregation of the mix. Reinforcement placing should
allow compaction by immersion vibrator. Within the
11.3 Placing of Reinforcement
concrete mass, different types of metal in contact
Rough handling, shock loading (prior to embedment) should be avoided to ensure that bimetal corrosion does
and the dropping of reinforcement from a height should not take place.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 21


12 TRANSPORTING, PLACING, COMPACTION of joint immediately after initial setting of concrete
AND CURING and to clean out the same immediately thereafter. The
prepared surface should be in a clean saturated surface
12.1 Transporting and Handling
dry condition when fresh concrete is placed, against
After mixing, concrete shall be transported to the it.
formwork as rapidly as possible by methods which will
In the case of construction joints at locations where
prevent the segregation or loss of any of the ingredients
the previous pour has been cast against shattering the
or ingress of foreign matter or water and maintaining
recommended method of obtaining a rough surface for
the required workability.
the previously poured concrete is to expose the
12.1.1 During hot or cold weather, concrete shall be aggregate with a high pressure water jet or any other
transported in deep containers. Other suitable methods appropriate means.
to reduce the loss of water by evaporation in hot
Fresh concrete should be thoroughly vibrated near
weather and heat loss in cold weather may also be
construction joints so that mortar from the new concrete
adopted.
flows between large aggregates and develop proper
12.2 Placing bond with old concrete.

The concrete shall be deposited as nearly as practicable Where high shear resistance is required at the
in its final position to avoid rehandling. The concrete construction joints, shear keys may be provided.
shall be placed and compacted before initial setting of Sprayed curing membranes and release agents should
concrete commences and should not be subsequently be thoroughly removed from joint surfaces.
disturbed. Methods of placing should be such as to
preclude segregation. Care should be taken to avoid 12.5 Curing
displacement of reinforcement or movement of
Curing is the process of preventing the loss of moisture
formwork. As a general guidance, the maximum
from the concrete whilst maintaining a satisfactory
permissible free fall of concrete maybe taken as 1.5 m.
temperature regime. The prevention of moisture loss
12.3 Compaction from the concrete is particularly important if the water-
cement ratio is low, if the cement has a high rate of
Concrete should be thoroughly compacted and fully strength development, if the concrete contains
worked around the reinforcement, around embedded granulated blast furnace slag or pulverized fuel ash.
fixtures and into comers of the formwork. The curing regime should also prevent the development
12.3.1 Concrete shall be compacted using mechanical of high temperature gradients within the concrete.
vibrators complying with accepted standard The rate of strength development at early ages of
[6-5 A(28)]. Over vibration and under vibration of concrete made with supersulphated cement is
concrete are harmful and should be avoided. Vibration significantly reduced at lower temperatures.
of very wet mixes should also be avoided. Supersulphated cement concrete is seriously affected
Whenever vibration has to be applied externally, the by inadequate curing and the surface has to be kept
design of formwork and the disposition of vibrators moist for at least seven days.
should receive special consideration to ensure efficient 12.5.1 Moist Curing
compaction and to avoid surface blemishes.
Exposed surfaces of concrete shall be kept continuously
12.4 Construction Joints and Cold Joints in a damp or wet condhion by pending or by covering
with a layer of sacking, canvas, hessian or similar
Joints are a common source of weakness and, therefore,
materials and kept constantly wet for at least seven
it is desirable to avoid them. If this is not possible,
days from the date of placing concrete in case of
their number shall be minimized. Concreting shall be
ordinary Portland Cement and at least 10 days where
carried out continuously up to construction joints, the
mineral admixtures or blended cements are used. The
position and arrangement of which shall be indicated
period of curing shall not be less than 10 days for
by the designer. Construction joints should comply
concrete exposed to dry and hot weather conditions.
with accepted standard [6-5 A(29)].
In the case of concrete where mineral admixtures or
Construction joints shall be placed at accessible blended cements are used, it is recommended that
locations to permit cleaning out of laitance, cement above minimum periods may be extended to 14 days.
slurry and unsound concrete, in order to create roughl
12.5.2 Membrane Curing
uneven surface. It is recommended to clean out laitance
and cement slurry by using wire brush on the surface Approved curing compounds may be used in lieu of

22 NATIONAL BUILDING CODE OF INDIA


moist curing with the permission of the engineer-in- The methods to be used for depositing concrete under
charge. Such compounds shall be applied to all exposed water shall be one of the following:
surfaces of the concrete as soon as possible after the
a) Tremie — The concrete is placed through
concrete has set. Impermeable membranes such as
vertical pipes the lower end of which is always
polyethylene sheeting covering closely the concrete
inserted sufficiently deep into the concrete
surface may also be used to provide effective barrier
which has been placed previously but has not
against evaporation.
set. The concrete emerging from the pipe
12.6 Supervision pushes the material that has already been
placed to the side and upwards and thus does
It is exceedingly difficult and costly to alter concrete not come into direct contact with water.
once placed. Hence, constant and strict supervision of
When concrete is to be deposited under-water
all the items of the construction is necessary during
by means of tremie, the top section of the
the progress of the work, including the proportioning
tremie shall be a hopper large enough to hold
and mixing of the concrete. Supervision is also of
one entire batch of the mix or the entire
extreme importance to check the reinforcement and
contents the transporting bucket, if any. The
its placing before being covered.
tremie pipe shall be not less than 200 mm in
12.6.1 Before any important operation, such as diameter and shall be large enough to allow a
concreting or stripping of the formwork is started, free flow of concrete and strong enough to
adequate notice shall be given to the construction withstand the external pressure of the water
supervisor. in which it is suspended, even if a partial --
vacuum develops inside the pipe. Preferably,
13 CONCRETING UNDER SPECIAL flanged steel pipe of adequate strength for the
CONDITIONS job should be used. A separate lifting device
13.1 Work in Extreme Weather Conditions shall be provided for each tremie pipe with
its hopper at the upper end. Unless the lower
During hot or cold weather, the concreting should be end of the pipe is equipped with an approved
done as per good practice [6-5 A(30)]. automatic check valve, the upper end of the
pipe shall be plugged with a wadding of the
13.2 Under-Water Concreting
gunny sacking or other approved material
13.2.1 When it is necessary to deposit concrete under before delivering the concrete to the trernie 8
water, the methods, equipment, materials and pipe through the hopper, so that when the
proportions of the mix to be used shall be submitted to concrete is forced down from the hopper to
and approved by the engineer-in-charge before the the pipe, it will force the plug (and along with
work is started. it any water in the pipe) down the pipe and
out of the bottom end, thus establishing a
13.2.2 Under-water concrete should have a slump
continuous stream of concrete. It will be
recommended in 6.1. The water-cement ratio shall not
necessary to raise slowly the tremie in order
exceed 0.6 and may need to be smaller, depending on
to cause a uniform flow of the concrete, but
the grade of concrete or the type of chemical attack.
the tremie shall not be emptied so that water
For aggregates of 40 mm maximum particle size, the
enters the pipe. At ,all times after the placing
cement content shall beat least 350 kg/m3 of concrete.
of concrete is started and until all the concrete
13.2.3 Coffer-dams or forms shall be sufficiently tight is placed, the lower end of the tremie pipe
to ensure still water if practicable, and in any case to shall be below the tpp surface of the plastic
reduce the flow of water to less than 3 mlmin through concrete. This will iause the concrete to build
the space into which concrete is to be deposited. Coffer- up from below instead of flowing out over
dams or forms in still water shall be sufficiently tight the surface, and thus avoid formation of
to prevent loss of mortar through the walls. De- laitance layers. If the charge in the tremie is
watering by pumping shall not be done while concrete lost while depositing, the tremie shall be
is being placed or until 24 h thereafter. raised above the concrete surface, and unless
13.2.4 Concrete cast under water should not fall freely sealed by a check valve, it shall be re-plugged
through the water. Otherwise it may be leached and at the top end, as at the beginning, before
become segregated. Concrete shall be deposited refilling for depositing concrete.
continuously until it is brought to the required height. b) Directplacement withpumps — As in the case
While depositing, the top surface shall be kept as nearly of the tremie method, the vertical end piece
level as possible and the formation of seams avoided. of the pipeline is always inserted sufficiently

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 23


f--”
k.

deep into the previously cast concrete and care shall be exercised not to disturb the concrete as
should not move to the side during pumping. far as possible while it is being deposited.
c) Drop bottom bucket — The top of the bucket
14 SAMPLING AND STRENGTH OF DESIGNED
shall be covered with a canvas flap. The
CONCRETE MIX
bottom doors shall open freely downward and
outward when tripped. The bucket shall be 14.1 General
filled completely and lowered slowly to avoid
Samples from fresh concrete shall be taken as per
backwash. The bottom doors shall not be
accepted standard [6-5A( 16)] and cubes shall be made,
opened until the bucket rests on the surface
cured and tested at 28 days in accordance with accepted
upon which the concrete is to be deposited
standard [6-5A(9)] .
and when discharged, shall be withdrawn
slowly until well above the concrete. 14.1.1 In order to get a relatively quicker idea of the
d) Bags — Bags of at least 0.028 m’ capacity of quality of concrete, optional tests on beams for modulus
jute or other coarse cloth shall be filled about of rupture at 72 &2 h or at 7 days, or compressive
two-thirds full of concrete, the spare end turned strength tests at 7 days maybe carried out in addition
under so that bag is square ended and securely to 28 days compressive strength test. For this purpose
tied. They shall be placed carefully in header the values should be arrive at based on actual testing.
and stretcher courses so that the whole mass is In all cases, the 28 days compressive strength specified
interlocked. Bags used for this purpose shall in Table 2 shall alone be the criterion for acceptance
or rejection of the concrete.
be free from deleterious materials.
--
e) Grouting — A series of round cages made 14.2 Frequency of Sampling
from 50mmmesh of 6 mm steel and extending
14.2.1 Sampling Procedure
over the full height to be concreted shall be
prepared and laid vertically over the area to A random sampling procedure shall be adopted to
be concreted so that the distance between ensure that each concrete batch shall have a reasonable
centres of the cages and also to the faces of chance of being tested that is, the sampling should be
the concrete shall not exceed 1 m. Stone spread over the entire period of concreting and cover
aggregate of not less than 50 mm nor more all mixing units.
than 200 mm size shall be deposited outside
14.2.2 Frequency
the steel cages over the full area and height
to be concreted with due care to prevent The minimum frequency of sampling of concrete of
displacement of the cages. each grade shall be in accordance with the following:
A stable 1:2 cement-sand grout with a water-
cement ratio of not less than 0,6 and not more Quantity of Concrete Number of Samples
in the Work, m3
than 0.8 shall be prepared in a mechanical
mixer and sent down under pressure (about 1-5 1
0.2 N/mmz) through 38 to 50 mm diameter 6-15 2
pipes terminating into steel cages, about 16-30 3
50 mm above the bottom of the concrete. As 31-50 4
the grouting proceeds, the pipe shall be raised 51 and above 4 plus one additional sample
gradually up to a height of not more than for each additional 50 m3 or
part thereof
6000 mm above its starting level after which
it may be withdrawn and placed into the next NOTE — At least one sample shatl be taken from each shift.
cage for further grouting by the same Where concrete is produced at continuous production unit,
procedure. such as ready-mixed concrete plant, frequency of sampling
may be agreed upon mutually by suppliers and purchasers.
After grouting the whole area for a height of
about 600 mm, the same operation shall be 14.3 Test Specimen
repeated, if necessary, for the next layer of
Three test specimens shall be made for each sample
600 mm and so on.
for testing at 28 days. Additional specimens may be
The amount of grout to be sent down shall be
required for various purposes such as to determine the
sufficient to fill all the voids which may be
strength of concrete at 7 days or at the time of striking
either ascertained or assumed as 55 percent
the formwork, or to determine the duration of curing,
of the volume to be concreted.
or to check the testing error. Additional specimens may
13.2.5 To minimize the formulation of laitance, great also be required for testing specimens cured by

24 NATIONAL BUILDJNG CODE OF INDIA


accelerated methods as described in accepted standard four consecutive test results shall include the batches
[6-5 A(31)]. The specimen shall be tested as described from which the first and last samples were taken
in accepted standard [6-5A(9)]. together with all intervening batches.

14.4 Test Results of Sample For the individual test result requirements given inCO13
of Table 11 or in 15.2 (b), only the particular batch
The test results of the sample shall be the average of from which the sample was taken shall beat risk.
the strength of three specimens. The individual
variation should not be more than & 15 percent of the Where the mean rate of sampling is not specified the
average. If more, the test results of the sample are maximum quantity of concrete that four consecutive
invalid. test results represent shall be limited to 60 m3.

15 ACCEPTANCE CRITERIA 15.4 If the concrete is deemed not to comply pursuant


to 15.1 or 15.2 as the case may be, the structural
15.1 Compressive Strength adequacy of the parts affected shall be investigated
The concrete shall be deemed to comply with the (see 16) and any consequential action as needed shall
strength requirements when both the following be taken.
conditions are met: 15.5 Concrete of each grade shall be assessed
a) The mean strength determined from any separately.
group of four non-overlapping consecutive 15.6 Concrete is liable to be rejected if it is porous or
test results complies with the appropriate honey-combed, its placing has been interrupted without
limits inCO12 of Table 11. providing a proper construction joint, the reinforcement
b) Any individual test result complies with the has been displaced beyond the tolerances specified, or
appropriate limits in CO13 of Table 11. construction tolerances have not been met. However,
the hardened concrete may be accepted after carrying
15.2 Flexural Strength out suitable remedial measures to the satisfaction of
When both the following conditions are met, the the engineer-in-charge.
concrete complies with the specified flexural strength:
16 INSPECTION AND TESTING OF
a) The mean strength determined from any STRUCTURES
group of four consecutive test results exceeds
16.1 Inspection
the specified characteristic strength by at least
0.3 N/mm*. To ensure that the construction complies with the
b) The strength determined from any test result design an inspection procedure should be set up
is not less than the specified characteristic covering materials, records, workmanship and
strength less 0.3 N/mm*. construction.

16.1.1 Tests should be made on reinforcement and the


15.3 Quantity of Concrete Represented by Strength
constituent materials of concrete in accordance with
Test Results
the relevant standards. Where applicable, use should
The quantity of concrete represented by a group of be made of suitable quality assurance schemes.

Table 11 Characteristic Compressive Strength Compliance ~equirement


(Clauses 15.1 and 15.3)
.:
Specified Grade Mean of the Group of 4 Non-Overlap~ing Couaeeutive Individual Test Results
Test Results in N/mm in N/ntm2
(1) (2) (3)

M 15 >~,~+ 0.825 x established standard deviation (rounded off to nearest 0.5 Nhnm2) > fck-3 NAnrn2
or
J&+ 3 N/mrn2, whichever is greater

M 20 or above >~k + 0.825 x established standard deviation (rounded off to nearest 0.5 N/mmz) >J~ – 4 N/mm*

f., +O;N/mm’, whichever is greater


NOTE — In the absence of established vatue of standard deviation, the vatues given in Table 8 may be assumed, and attempt should
be made to obtain results of 30 samples as early as possible to establish the vatue of standard deviation.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 25


16.1.2 Care should be taken to see that: NOTE — Dead load includes self weight of the structural
members plus weight of finishes and walls or partitions, if any,
a) design and detail are capable of being as considered in the design.
executed to a suitable standard, with due
16.6.3 The deflection due to imposed load only shall
allowance for dimensional tolerances;
be recorded. If within 24 h of removal of the imposed
b) there are clear instructions on inspection load, the structure does not recover at least 75 percent
standards; of the deflection under superimposed load, the test may
c) there are clear instructions on permissible be repeated after a lapse of 72 h. If the recovery is less
deviations; than 80 percent, the structure shall be deemed to be
d) elements critical to workmanship, structural unacceptable.
performance, durability and appearance are
16.6.3.1 If the maximum deflection in mm, shown
identified; and
during 24 h under load is less than 40 l?D, where 1 is
e) there is a system to verify that the quality is the effective span in m; and D, the overall depth of the
satisfactory in individual parts of the structure, section in mm, it is not necessary for the recovery to
especially the critical ones. be measured and the recovery provisions of 16.6.3 shall
16.2 Immediately after stripping the formwork, all not apply.
concrete shall be carefully inspected and any defective 16.7 Members Other than Flexural Members
work or small defects either removed or made good
before concrete has thoroughly hardened. Members other than flexural members should be
preferably investigated by analysis.
16.3 Testing
16.8 Non-destructive Tests
In case of doubt regarding the grade of concrete used,
Non-destructive tests are used to obtain estimation of
either due to poor workmanship or based on results of
the properties of concrete in the structure. The methods
cube strength tests, compressive strength tests of
adopted include ultrasonic pulse velocity (see accepted
concrete on the basis of 16.4 and/or load test (see 16.6)
standard [6-5 A(32)] ), probe penetration, pullout and
may be carried out.
maturity. Non-destructive tests provide alternatives to
16.4 Core Test core tests for estimating the strength of concrete in a
structure, or can supplement the data obtained from a
16.4.1 The points from which cores are to be taken limited number of cores. These methods are based on
and the number of cores required shall be at the measuring a concrete property that bears some
discretion of the engineer-in-charge and shall be relationship to strength. The accuracy of these methods,
representative of the whole of concrete concerned. In in part, is determined by the degree of correlation
no case, however, shall fewer than three cores be tested. between strength and the physical quality measured
16.4.2 Cores shall be prepared and tested as described by the non-destructive tests.
in accepted standard [6-5A(9)]. Any of these methods maybe adopted, in which case
16.4.3 Concrete in the member represented by a core the acceptance criteria shall be agreed upon prior to
test shall be considered acceptable if the average testing.
equivalent cube strength of the cores is equal to at least
85 percent of the cube strength of the grade of concrete SECTION 5A (C) GENERAL DESIGN
specified for the corresponding age and no individual CONS15ERATION
core has a strength less than 75 percent.
17 BASES FOR DESIGN
16.5 In case the core test results do not satisfy the
requirements of 16.4.3 or where such tests have not 17.1 Aim of Design
been done, load test (16.6) may be restored to. The aim of design is the achievement of an acceptable
16.6 Load Tests for Flexural Member probability that structures being designed will perform
satisfactorily during their intended life. With an
16.6.1 Load tests should be carried out as soon as appropriate degree of safety, they should sustain all
possible after expiry of 28 days from the time of placing the loads and d&formations of normal construction and
of concrete. use and have adequate durability and adequate
16.6.2 The structure should be subjected to a load resistance to the effects of misuse and fire.
equal to full dead load of the structure plus 1.25 times 17.2 Methods of Design
the imposed load for a period of 24 h and then the
imposed load shall be removed. 17.2.1 Structure and structural elements shall normally

26 NATIONAL BUILDING CODE OF INDIA


P’

be designed by Limit State Method. Account should The realization of design objectives requires
be taken of accepted theories, experiment and compliance with clearly defined standards for
experience and the need to design for durability. materials, production, workmanship and also
Calculations alone do not produce safe, serviceable and maintenance and use of structure in service.
durable structures. Suitable materials, quality control,
adequate detailing and good supervision are equally 18 LOADS AND FORCES
important. 18.1 General
17.2.2 Where the Limit State Method can not be In structural design, account shall be taken of the dead,
conveniently adopted, Working Stress Method may be imposed and wind loads and forces such as those
used (see Annex B). caused by earthquake, and effects due to shrinkage,
17.2.3 Design Based on Experimental Basis creep, temperature, etc, where applicable.

Designs based on experimental investigations on 18.2 Dead Loads


models or full size structure or element may be
accepted if they satisfy the primary requirements Dead loads shall be calculated on the basis of unit
of 17.1 and subject to experimental details and the weights which shall be established taking into
analysis connected therewith being approved by the consideration the materials specified for construction.
engineer-in-charge. 18.2.1 Alternatively, the dead loads may be calculated
17.2.3.1 Where the design is based on experimental on the basis of unit weights of materials given in good
investigation on full size structure or element, load tests practice [6-5 A(33)]. Unless more accurate calculations
shall be carried out to ensure the following: are warranted, the unit weights of plain concrete and
reinforced concrete made with sand and gravel or
a) The structure shall satisfy the requirements
crushed natural stone aggregate may be taken as
for deflection (see 22.2) and cracking
24 kN/m3 and 25 kN/m3 respectively.
(see 34.3.2) when subjected to a load for 24 h
equal to the characteristic load multiplied by 18.3 Imposed Loads, Wind Loads and Snow Loads
1.33 Y,where Y,shall be taken from Table 18,
Imposed loads, wind loads and snow loads shall be
for the limit state of serviceability. If within
assumed in accordance with good practice
24 h of the removal of the load, the structure
[6-5 A(33)].
does not show a recovery of at least 75 percent
of the maximum deflection shown during the
18.4 Earthquake Forces
24 h under the load, the test loading should
be repeated after a lapse of 72 h. The recovery The earthquake forces shall be calculated in accordance
after the second test should be at least 75 with accepted standard [6-5 A(34)].
percent of the maximum deflection shown
18.5 Shrinkage, Creep and Temperature Effects
during the second test.
NOTE — lf the maximum deflection in mm, shown If the effects of shrinkage, creep and temperature are
during 24 h under load is less than 40 12/D where 1is liable to affect materially the safety and serviceability
the effective span in m; and D is the overall depth of of the structure, these shall be taken into account in
the section in mm, it is not necessary for the recovery
to be measured. the calculations (see 5.2.4, 5.2.5 and 5.2.6) and good
practice [6-5 A(33)].
b) The structure shall have adequate strength to
sustain for 24 h, a total load equal to the 18.5.1 In ordinary buildings, such as low rise
characteristic load multiplied by 1.33 ‘Y~
where dwellings whose lateral dimension do not exceed 45 m,
‘Y~shall be taken from Table 18 for the limit the effects due to temperature fluctuations and
state of collapse. shrinkage and creep can be ignored in design
calculations.
17.3 Durability, Workmanship and Materials

It is assumed that the quality of concrete, steel and 18.6 Other Forces and Effects
other materials and of the workmanship, as verified In addition, account shall be taken of the following
by inspections, is adequate for safety, serviceability forces and effects if they are liable to affect materially
and durability. the safety and serviceability of the structure:
17.4 Design Process a) Foundation movement (see good practice
Design, including design for durability, construction [6-5A(35)] ),
and use in service should be considered as a whole. b) Elastic axial shortening,

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 27


c) Soil and fluid pressures (see good practice of probable variations in dead load during construction,
[6-5 A(33)] ), repair or other temporary measures. Wind and seismic
d) Vibration, loading shall be treated as imposed loading.
e) Fatigue,
19.4 Moment Connection
f) Impact (see good practice [6-5A(33)] ),
In designing the framework of a building provisions
g) Erection loads (see good practice [6-5A(33)] ),
shall be made by adequate moment connections or by
and
a system of bracings to effectively transmit all the
h) Stress concentration effect due to point load
horizontal forces to the foundations.
and the like.
18.7 Combination of Loads 19.5 Lateral Sway

The combination of loads shall be as given in good Under transient wind load the laterrd sway at the top
practice [6-5A(33)]. should not exceed H/500, where His the total height
of the building. For seismic loading, reference should
18.8 Dead Load Counteracting Other Loads and be made to good practice [6-5A(34)].
Forces
20 FIRE RESISTANCE
When dead load counteracts the effects due to other
loads and forces in structural member or joint, special 20.1 A structure or structural element required to have
care shall be exercised by the designer to ensure fire resistance should be designed to possess an
adequate safety for possible stress reversal. appropriate degree of resistance to flame penetration;
.-
heat transmission and failure. The f~e resistance of a
18.9 Design Load structural element is expressed in terms of time in hours
Design load is the load to be taken for use in the in accordance with good practice [6-5 A(36)]. Fire
appropriate method of design; it is the characteristic resistance of concrete elements depends upon details
load in case of working stress method and characteristic of member size, cover to steel reinforcement detailing
load with appropriate partial safety factors for limit and type of aggregate (normal weight or light weight)
state design. used in concrete. General requirements for fire
protection are given in good practice [6-5 A(37)]
19 STABILITY OF THE STRUCTURE
20.2 Minimum requirements of concrete cover and
19.1 Overturning member dimensions for normal weight aggregate
concrete members so as to have the required fire
The stability of a structure as a whole against
resistance shall be in accordance with 25.4.3 and Fig. 1
overturning shall be ensured so that the restoring
respectively.
moment shall be not less than the sum of 1.2 times the
maximum overturning moment due to the characteristic 20.3 The reinforcement detailing should reflect the
dead load and 1.4 times the maximum overturning changing pattern of the structural action and ensure
moment due to the characteristic imposed loads. In that both individual elements and the structure as a
cases where dead load provides the restoring moment, whole contain adequate support, ties, bonds and
only 0,9 times the characteristic dead load shall be anchorages for the required fire resistance.
considered. Restoring moment due to imposed loads
20.3.1 Additional measures such as application of fire
shall be ignored.
resistant finishes, provision of fire resistant false
19.1.1 The anchorages or counterweights provided for ceilings and sacrificial steel in tensile zone, should be
overhanging members (during construction and adopted in case the nomi,nal cover required exceeds
service) should be such that static equilibrium should 40 mm for beams and 35 mm for slabs, to give
remain, even when overturning moment is doubled. protection against spalling.

19.2 Sliding 20.4 Specialist literature may be referred to for


determining fue resistance of the structures which have
The structure shall have a factor against sliding of not
not been covered in Fig. 1 or Table 16A.
less than 1.4 under the most adverse combination of the
applied characteristic forces. In this case only 0.9 times 21 ANALYSIS
the characteristic dead load shall be taken into account.
21.1 General
19.3 Probable Variation in Dead Load
All structures may be analyzed by the linear elastic
To ensure stability at all times, account shall be taken theory to calculate internal actions produced by design

28 NATIONAL BUILDING CODE OF INDIA


.. “.

El
0 .,.

●,.4-
. . . . . . . ..
. .
“’~’. .1 ..*.
. .. .. . . . .
-., ●.
. . . .. .
. . .“
., .. .’ - .,
. ...”.

. .
. . . . . ...”...

l--b-l

.. ..:,,.,:.
d &bw

SOLIDS SLAB RIB / WAFFEL SLAB

SLABS

‘El
,.
,..
“. ..4,
.!,.

:,. #., :, . ...


. . . .. .. ~,.::: ;
jO
...f:
..:. :: ..., ,,.!::~: !
,> ,. :,: , .... ..
., . . ...+. .... ,,, .,., ... ~“i;’+;
. ..+. ;4 ..’:” .! ;-.;<;.’:,*.
.. .. .... .. .,.,.,.
. . . . .. ...
50% EXPOSED ONE FACE EXPOSED

U b D

COLUMNS
FULLY EXPOSED

Fire Maximum Rib Minimum Column Dimension (b or D) Minimum Wall lhickness


Resistance Beam Width Thickness ~~
Width of of
Floors Fully 50% One Face p< O.4% 0.4% <p< 1% p>l%
Slabs
Exposed Exposed Exposed
h b b. D
nun mm mm mm mm mm mm mm mm
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo)

0.5 200 125 75 150 125 100 150 100 100


1 200 125 95 200 160 120 {50 120 100
1.5 200 125 110 250 200 140 175 140 100
2 200 125 125 300 200 160 — 160 100
3 240 150 150 400 300 200 — 200 150
4 280 175 170 450 350 240 — 240 180

NOTES
1 These minimum dimensions relate specifically to the covers given in Table 16A.
2 p is the percentage of steel reinforcement.

FIG. 1 MINIMUM DIMENSIONS OF REINFORCED CONCRETE MEMBERS


FOR FIRE RESISTANCE

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 29


loads. In lieu of rigorous elastic analysis, a simplified transformed on the basis of modular ratio
analysis as given in 21.4 for frames and as given in 21.5 (see B-1.3); or
for continuous beams may be adopted. c) Cracked section — The area of concrete in
compression plus the area of reinforcement
21.2 Effective Span
transformed on the basis of modular ratio.
Unless otherwise specified, the effective span of a
The assumptions made shall be consistent for all the
member shall be as follows:
members of the structure throughout any analysis.
a) Simply Supported Beam or Slab — The
21.3.2 For deflection calculations, appropriate values
effective span of a member that is not built
of moment of inertia as specified in Annex C should
integrally with it supports shall be taken as
be used,
clear span plus the effective depth of slab
or beam or centre to centre of supports, 21.4 Structural Frames
whichever is less.
The simplifying assumptions as given in 21.4.1
b) Continuous Beam or Slab — In the case of
to 21.4.3 may be used in the analysis of frames.
continuous beam or slab, if the width of the
support is less than 1/12 of the clear span, the 21.4.1 Arrangement of Imposed Load
effective span shall be as given in 21.2 (a). If
a) Consideration maybe limited to combinations .
the supports are wider than 1/12 of the clear
of
span or 600 mm whichever is less, the
1) Design dead load on all spans with full
effective span shall be taken as under:
design imposed load on two adjacent
1) For end span with one end fixed and the
SpallS; and
other continuous or for intermediate
spans, the effective span shall be the clear 2) Design dead load on all spans with full
span between supports; design imposed load on alternate spans.

2) For end span with one end free and the b) When design imposed load does not exceed
other continuous, the effective span shall three-fourths of the design dead load, the load
be equal to the clear span plus half the arrangement may be design dead load and
effective depth of the beam or slab or design imposed load on all the spans.
the clear span plus half the width of the NOTE— For beamsand slabs continuousover support
discontinuous support, whichever is 21.4.1 (a) may be assumed.
less; 21.4.2 Substitute Frame
3) In the case of spans with roller or rocket
For determining the moments and shears at any floor
bearings, the effective span shall always
or roof level due to gravity loads, the beams at that
be the distance between the centres of
level together with columns above and below with their
bearings.
far ends fixed may be considered to constitute the
c) Cantilever — The effective length of a frame.
cantilever shall be taken as its length to the
face of the support plus half the effective 21.4.2.1 Where side sway consideration becomes
depth except where it forms the end of a critical due to unsymmetry in geometry or loading,
continuous beam where the length to the rigorous analysis may be required.
centre of support shall be taken. 21.4.3 For lateral loads, simplified methods may be
d) Frames — In the analysis of a continuous used to obtain the moments and shears for structures
frame, centre-to-centre distance shall be used. that are symmetrical. For unsymmetrical or very tall
structures, more rigorous methods should be used.
21.3 Stiffness
21.5 Moment and Shear Coefficients for Continuous
21.3.1 Relative Sti@ess
Beams
The relative stiffness of the members maybe based on
21.5.1 Unless more exact estimates are made, for
the moment of inertia of the section determined on the
beams of uniform cross-section which support
basis of any one of the following definitions:
substantially uniformly distributed loads over three or
a) Gross section — The cross-section of the more spans which do not differ by more than 15 percent
member ignoring reinforcemen~ of the longest, the bending moments and shear forces
b) Transformed section — The concrete cross- used in design may be obtained using the coefficients
section plus the area of reinforcement given in Table 12 and Table 13 respectively.

30 NATIONAL BUILDING CODE OF INDIA


Table 12 Bending Moment Coefficients
(Clause 21.5.1)

Type of Load Span Moments Support Momenta


~~
Near Middle of At Middle of At Support Next to the At Other Interior
End Span Interior Span End Support supports
(1) (2) (3) (4) (5)

1 1 1 1
Dead load and imposed load (fixed) +— +—
12 16 –G –z
1 1. 1 1
Imposed load (not fixed) +— +— -— -—
10 12. 9 9

NOTE — For obtaining the bending moment, the coefficient shatl be multiplied by the totat design load and effective span.

Table 13 Shear for Coeffkients


(Clauses 21.5.1 and 21.5.2)

Type of Load At End Snpport At Support Next to the End Support At AU Other Interior
/ A
Y supporta
Outer Side Inner Side
(1) (2) (3) (4) (5)

Dead load and imposed load (fixed) 0.4 0.6 0.55 0.5
Imposed load (not fixed) 0.45 0.6 0.6 0.6

NOTE — For obtaining the shear force, the coet%cient shatl be multiplied by the totat design load.

For moments at supports where two unequal spans meet be used in the design of the member at that section
or in case where the spans are not equally loaded, the except as in 21.6.2.1.
average of the two values for the negative moment at
21.6.2.1 When the reaction in the direction of the
the support may be taken for design.
applied shear introduces compression into the end
Where coefficients given in Table 12 are used for region of the member, sections located at a distance
calculation of bending moments, redistribution referred less than d from the face of the support maybe designed
to in 21.7 shall not be permitted. for the same shear as that computed at distance d
(see Fig. 2).
21.5.2 Beams and Slabs Over Free End Supports
NOTE — The above clauses are applicable for beams generally
Where a member is built into a masonry wall which carrying uniformly distributed load or where the principaf load
is located farther than 2d from the face of the support.
develops only partial restraint, the member shall be
designed to resist a negative moment at the face of the 21.7 Redistribution of Moments
support of W1124 where W is the total design load and
Redistribution of moments maybe done in accordance
1is the effective span, or such other restraining moment
with 36.1.1 for Limit State Method and in accordance
as maybe shown to be applicable. For such a condition
with B-1.2 for Working Stress Method. However,
shear coefficient given in Table 13 at the end support
where simplified artalysis’using coefficients is adopted,
may be increased by 0.05.
redistribution of moments shall not be done.
21.6 Critical Sections for Moment and Shear
22 BEAMS
21.6.1 For monolithic construction, the moments
22.0 Effective Depth
computed at the face of the supports shall be used in
the design of the members at those section. For non- Effective depth of a beam is the distance between the
monolithic construction the design of the member shall centroid of the area of tension reinforcement and the
be done keeping in view 21.2. maximum compression fibre, excluding the thickness
of finishing material not placed monolithically with
21.6.2 Critical Section for Shear
the member and the thickness of any concrete provided
The shears computed at the face of the support shall to allow for wear. This will not apply to deep beams.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 31


A
I

I
.

(b) (c)
(a)

FIG. 2 TYPICAL SPORT CONDITIONS FOR LOCATING FACTORED SHEAR FORCE

22.1 T-Beams and L-Beams where

22.1.1 General b, = Effective width of flange,


10 = Distance between points of zero moments .-.
A slab which is assumed to act as a compression flange
in the beam,
of a T-beam or L-beam shall satisfy the following:
bW = Breadth of the web,
a) The slab shall be cast integrally with the web,
D~ = Thickness of flange, and
or the web and the slab shall be effectively
b= Actual width of the flange.
bonded together in any other manner; and
b) If the main reinforcement of the slab is parallel NOTE — For continuous beams and frames, /0 may
be assumed as 0.7 times the effective span.
to the beam, transverse reinforcement shall
be provided as in Fig. 3; such reinforcement 22.2 Control of Deflection
shall not be less than 60 percent of the main
reinforcement at mid span of the slab. The deflection of a structure or part thereof shall not
adversely affect the appearance or efficiency of the
22.1.2 Effective Width of Flange structure or finishes or partitions. The deflection shall
In the absence of more accurate determination, the generally be limited to the following:
effective width of flange maybe taken as the following a) The final deflection due to all loads including
but in no case greater than the breadth of the web plus the effects of temperature, creep and
half the sum of the clear distances to the adjacent beams shrinkage and measured from the as-cast level
on either side. of the supports of floors, roofs and all other
horizontal members, should not normally
a) For T-beams, b~ = ~ + bw + 6 D~ exceed span1250.
b) The deflection including the effects of
temperature, creep and s~nkage occurring
b) For L-beams, b~ = &+ bw + 3 D~ after erection of partitions and the application
of finishes should not normally exceed spad
c) For isolated beams, the effective flange width 350 or 20 mm whichever is less.
shall be obtained as below but in no case
greater than the actual width: 22.2.1 The vertical deflection limits may generally be
assumed to be satisfied provided that the span to depth
10 ratios are not greater than the values obtained as below:
T-beams, b~ = —+bw
1 a) Basic values of span to effective depth ratios
~ +4
() b for spans up to 10 m:
0.51 Cantilever 7
L-beams, b~ = ~i-bW
10 +4 Simply supported 20
[-)b Continuous 26

32 NATIONALBUILDING CODE OF INDIA


——. ———,
––-–l–l–––
BEAM
+7

..-
SECTION XX

FIG. 3 TRANSVERSE REINFORCEMENTIN FLANGE OF T-BEAM WHEN


MAIN REINFORCEMENTOF SLAB IS PARALLEL TO THE BEAM

b) For spans above 10 m, the values in (a) may For a cantilever, the clear distance from the free end
be multiplied by 10/span in metres, except of the cantilever to the lateral restraint shall not
for cantilever in which case deflection 100 b’
exceed 25 b or — whichever is less.
calculations should be made. d
c) Depending on the area and the stress of steel
for tension reinforcement, the values in (a) 23 SOLID SLABS
or (b) shall be modified by multiplying with
23.1 General
the modification factor obtained as per Fig. 4.
d) Depending on the area of compression The provisions of 22.2 for beams apply to slabs also.
reinforcement, the value of span to depth ratio NOTES
be further modified by multiplying with the 1 For slabs spanning in two directions, the shorter of the two
modification factor obtained as per Fig. 5. spans should be used for calculating the span to effective depth
ratios.
e) For flanged beams, the values of(a) or (b) be
2 For two-way slabs of shorter spans (up to 3.5 m) with mild
modified as per Fig. 6 and the reinforcement steel reinforcement, the span to overall depth ratios given below
percentage for use in Fig. 4 and 5 should be may generally be assumed to satisfy vertical deflection limits
based on area of section equal to b~d. for loading class up to 3 kN/m2.
NOTE — When deflections are required to be Simply supported slabs 35
calculated,the method given in Annex C may be used. Continuous slabs ‘ 40

22.3 Slenderness Limits for Beams to Ensure For high strength deformed bars of grade Fe 415, the values
given above should be multiplied by 0.8.
Lateral Stability

A simply supported or continuous beam shall be so 23.2 Slabs Continuous Over Supports
proportioned that the clear distance between the lateral Slabs spanning in one direction and continuous over
250 b’ supports shall be designed according to the provisions
restraints does not exceed 60 b or — whichever applicable to continuous beams.
d
is less, where d is the effective depth of the beam and
23.3 Slabs Monolithic with Supports
b the breadth of the compression face midway between
the lateral restraints. Bending moments in slabs (except flat slabs)

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 33


t-1 Note: fs IS STEEL STRESS OF SERVICE LOADS
IN N/mm 2 H

I
0.4 0.8 1.2 1.6 2.0 2.4 2.83,0
*
PERCENTAGE TENSION REINFORCEMENT
Area of cross- section ofsteel required
fs=Q.58fy A
rea of cross - section of steel provided

FIG. 4 MODIFICATIONFACTOR FORTENSION REINFORCEMENT

1.5

1.4

1.3

1.2
1.1
10
..-
0 0.50 1.00 1.50 2.00 2.50 3.00

PERCENTAGE COMPRESSION REINFORCEMENT


,
FIG. 5 MODIFICATIONFACTOR FORCOMPRESSIONREINFORCEMENT

1.00
0.95

0.90

0.85

0.80

0.75

0.70

RATlO OF WEB WIDTH TO FLANGE WIDTH

FIG. 6 REDUCTIONFACTORS FORRATIOS OF SPAN TO EFFECTIVEDEPTH


FORFLANGED BEAMS

34 NATIONAL BUILDING CODE OF INDIA

..
constructed monolithically with the supports shall be Table 14 Values of k for Simply Supported
calculated by taking such slabs either as continuous and Continuous Slabs
over supports and capable of free rotation, or as (Clause 24.3.2.1)
members of a continuous framework with the supports,
taking into account the stiffness of such supports. If lne k for Simply k for Continuous
such supports are formed due to beams which justify Supported Slabs Slabs

fixity at the support of slabs, then the effects on the (1) (2) (3)

supporting such as, the bending of the web in


beam, 0.1 0.4 0.4
the transverse direction of the beam and the torsion in 0.2 0.8 0.8
0.3 1.16 1.16
the longitudinal direction of the beam, wherever 0.4 1.48 1.44
applicable, shall also be considered in the design of 0.5 1.72 1.68
the beam. 0.6 : 1.96 1.84
0.7 2.12 1.96
23.3.1 For the purpose of calculation of moments in 0.8 2.24 2.08
0.9 2.36 2.16
slabs in a monolithic structure, it will generally be
1.0 and above 2.48 2.24
sufficiently accurate to assume that members connected
to the ends of such slabs are fixed in position and b) For two or more concentrated loads placed in
direction at the ends remote from their connections a line in the direction of the span, the bending
with the slabs. moment per metre width of slab shall be
23.3.2 Slabs Carrying Concentrated Load calculated separately for each load according
to its appropriate effective width of slab
23.3.2.1 If a solid slab supported on two opposite calculated as in (a) above and added together
edges, carries concentrated loads the maximum for design calculations.
bending moment caused by the concentrated loads c) For two or more loads not in a line in the
shall be assumed to be resisted by an effective width
direction of the span, if the effective width of
of slab (measured parallel to the supporting edges)
slab for one load does not overlap the effective
as follows: width of slab for another load, both calculated
a) For a single concentrated load, the effective as in (a) above, then the slab for each load
width shall be calculated in accordance with can be designed separately. If the effective
the following equation provided that it shall width of slab for one load overlaps the
not exceed the actual width of the slab: effective width of slab for an adjacent load,
the overlapping portion of the slab shall be
designed for the combined effect of the two
loads.
d) For cantilever solid slabs, the effective width
where shall be calculated in accordance with the
following equation:
b~f = Effective width of slab,
k= Constant having the values given in b~f = 1.2a1+ a
Table 14 depending upon the ratio of
where
the width of the slab (l’) to the effective
span le~, b,, = Effective width,
x= Distance of the centroid of the al = Distance of the concentrated load from
concentrated load from nearer support, the face of the cantilever support, and
lcf = Effective span, and a = Width of’ contact area of the
a= Width of the contact area of the concentrated load measured parallel to
concentrated load from nearer support the supporting edge.
measured parallel to the supported Provided that the effective width of the cantilever
edge. slab shall not exceed one-third the length of the
And provided further that in case of a load cantilever slab measured parallel to the fixed edge.
near the unsupported edge of a slab, the And provided further that when the concentrated
effective width shall not exceed the above load is placed near the extreme ends of the length
value nor half the above value plus the of cantilever slab in the direction parallel to the
distance of the load from the unsupported fixed edge, the effective width shall not exceed
edge. the above value, nor shall it exceed half the above

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 35


value plus the distance of the concentrated load over the supports will need to be extended further. The
from the extreme end measured in the direction procedure should be as follows:
parallel to the fixed edge.
1) Take the span moment as parabolic between
23.3.2.2 For slabs other than solid slabs, the effective supports: its maximum value is as found
width shall depend on the ratio of the transverse and from (d).
longitudinal flexural rigidities of the slab. Where this 2) Determine the points of contraflexure of the
ratio is one, that is, where the transverse and new support moments [from (c)] with the span
longitudinal flexural rigidities are approximately equal, moment [from (1)].
the value of effective width as found for solid slabs 3) Extend half the support tension steel at each
may be used. But as the ratio decreases, proportionately end to at least an effective depth or 12 bar
smaller value shall be taken. diameters beyond the nearest point of
23.3.2.3 Any other recognized method of analysis for contraflexure.
cases of slabs covered by 23.3.2.1 and 23.3.2.2 and 4) Extend the full area of the support tension
for all other cases of slabs may be used with the steel at each end to half the distance from (3).
approval of the engineer-in-charge.
23.5 Loads on Supporting Beams
23.3.2.4 The critical section for checking shear shall
The loads on beams supporting solid slabs spanning
be as given in 33.2.4.1.
in two directions at right angles and supporting
23.4 Slabs Spanning in Two Directions at Right uniformly distributed loads, may be assumed to be in
Angles accordance with Fig. 7.

The slabs spanning in two directions at right angles


and carrying uniformly distributed load may be
designed by any acceptable theory or by using
coefficients given in Annex D. For determining
bending moments in slabs spanning in two directions
at right angles and carrying concentrated load, any
accepted method approved by the engineer-in-charge A
may be adopted.
NOTE — The most commonly used elastic methods are based
on Pigeaud’s or Wester guard’s theory and the most commonly ~ LOAD IN THIS SHADED < B
used limit state of collapse method is based on Johansen’s yield- AREA TO BE CARRIED
line theory. BY BEAM BEAM ‘B’

23.4.1 Restrained Slab with Unequal Conditions at FIG. 7 LOAD CARRIED BY SUPPORTED BEAMS

Adjacent Panels
24 COMPRESSION MEMBERS
in some cases the support moments calculated from
Table 26 for adjacent panels may differ significantly. 24.1 Definitions
The following procedure may be adopted to adjust 24.1.1 Column or strut is a compression member, the
them: effective length of which exceeds three times the least
a) Calculate the sum of moments at midspan and lateral dimension.
supports (neglecting signs). 24.1.2 Short and Slender Compression Members
b) Treat the values from Table 26 as fixed end
moments. A compression member may be consider~d as short
c) According to the relative stiffness of adjacent 1
when both the slenderness ratios ~ and ~ are less
spans, distribute the fixed end moments I!) b
across the supports, giving new support than 12:
moments.
where
d) Adjust midspan moment such that, when
added to the support moments from (c) 1 = Effective length in respect of the major axis,
(neglecting signs), the total should be equal ;= Depth in respect of the major axis,
to that from (a). 1 = Effective length in respect of the minor axis,
ey
H the resulting support moments are significantly and
greater than the value from Table 26, the tension steel b = Width of the member.

36 NATIONAL BUILDING CODE OF INDIA


It shall otherwise be considered as a slender 24.4 Minimum Eccentricity
compression member.
All columns shall be designed for minimum
24.1.3 Unsupported Length eccentricity, equal to the unsupported length of column/
500 plus lateral dimensions/30, subject to a minimum
The unsupported length, 1, of a compression member
of 20 mm. Where hi-axial bending is considered, it is
shall be taken as the clear distance between end
sufficient to ensure that eccentricity exceeds the
restraints except that:
minimum about one axis at a time.
a) in flat slab construction, it shall be clear
distance between the floor and the lower 25 REQUIREMENTS GOVERNING
extremity of the capital, the drop panel or slab REINFORCEMENT AND DETAILING
whichever is the least. 25.1 General
b) in beam and slab construction, it shall be the
Reinforcing steel of same type and grade shall be used
clear distance between the floor and the
as main reinforcement in a structural member.
underside of the shallower beam framing into
However, simultaneous use of two different types or
the columns in each direction at the next
grades of steel for main and secondary reinforcement
higher floor level.
respectively is permissible.
c) in columns restrained laterally by struts,
it shall be the clear distance between 25.1.1 Bars may be arranged singly, or in pairs in
consecutive struts in each vertical plane, contact, or in groups of three or four bars bundled in
provided that to be an adequate support, contact. Bundled bars shall be enclosed within stirrups
two such struts shall meet the columns at or ties. Bundled bars shall be tied together to ensure
approximately the same level and the angle the bars remaining together. Bars larger than 32 mm
between vertical planes through the struts diameter shall not be bundled, except in columns.
shall not vary more than 30° from a right
25.1.2 The recommendations for detailing for
angle. Such struts shall be of adequate
earthquake-resistant construction given in good
dimensions and shall have sufficient
practice [6-5 A(38)] should be taken into consideration,
anchorage to restrain the member against
where applicable (see also good practice [6-5A(38)] ).
lateral deflection.
d) in columns restrained laterally by struts or 25.2 Development of Stress in Reinforcement
beams, with brackets used at the junction, it
The calculated tension or compression in any bar at
shall be the clear distance between the floor
any section shall be developed on each side of the
and the lower edge of the bracket, provided
section by an appropriate development length or end
that the bracket width equals that of the beam
anchorage or by a combination thereof.
strut and is at least half that of the column.
25.2.1 Development Length of Bars
24.2 Effective Length of Compression Members
The development length L~ is given by
In the absence of more exact analysis, the effective
length /ef of columns maybe obtained as described in
~=~
Annex E.
bd
24.3 Slenderness Limits for Columns where
24.3.1 The unsupported length between end restraints = Nominal diameter of the bar,
4J
shall not exceed 60 times the least lateral dimension
Cr, = Stress in bar at the section considered at
of a column.
design load, and
24.3.2 If, in any given plane, one end of a column is Tbd = Design bond stress given in 25.2.1.1.
unrestrained, its unsupported length, 1, shall not
NOTES
100 b2
exceed — 1 The development length includes anchorage values of
D“ hooks in tension reinforcement.
2 For bars of sections other than circular, the development
where
length should be sufficient to develop the stress in the bar by
b = Width of that cross-section, and bond.

D = Depth of the cross-section measured in the 25.2.1.1 Design bond stress in limit state method for
plane under consideration. plain bars in tension shall be as below:

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 37


be as for bars in tension; this length shall be
Grade of M20 M25 M30 M35 M40 and
measured as under:
concrete above
1) In tension zone, from the end of the
Design bond 1.2 1.4 1.5 1.7 1.9 sloping or inclined portion of the bar, and
stress, TW
2) In the compression zone, from the mild
N/mmz
depth of the beam.
For deformed bars conforming to accepted standard b) Stirrups — Notwithstanding any of the
[6-5 A(40)] these values shall be increased by 60 provisions of this standard, incase of
percent. secondary reinforcement, such as stirrups and
transverse ties, complete development lengths
For bars in compression, the values of bond stress for
and anchorage shall be deemed to have been
bars in tension shall be increased by 25 percent.
provided when the bar is bent through an
The values of bond stress in working stress design, are angle of at least 90° round a bar of at least its
given in B-2.1. own diameter and is continued beyond the end
of the curve for a length of at least eight
25.2.1.2 Bars bundled in contact
diameters, or when the bar is bent through an
The development length of each bar of bundled bars angle of 135° and is continued beyond the
shall be that for the individual bar, increased by 10 end of the curve for a length of at least six
percent for two bars in contact, 20 percent for three bar diameters or when the bar is bent through
bars in contact and 33 percent for four bars in contact. an angle of 180° and is continued beyond the
---
end of the curve for a length of at least four
25.2.2 Anchoring Reinforcing Bars
bar diameters.
25.2.2.1 Anchoring bars in tension
25.2.2.5 Bearing stresses at bends
a) Deformed bars may be used without end
The bearing stress in concrete for bends and hooks
anchorages provided development length
described in good practice [6-5 A(26)] need not be
requirement is satisfied. Hooks should
checked. The bearing stress inside a bend in any other
normally be provide for plain bars in tension,
bend shall be calculated as given below:
b) Bends and hooks — Bends and hooks shall
conform to good practice [6-5 A(26)]: F
Bearing stress = ~
1) Bends — The anchorage value of bend
shall be taken as 4 times the diameter of
where
the bar for each 45° bend subject to a
maximum of 16 times the diameter of the F~, = Tensile force due to design loads in a bar
bar. or group of bars,
2) Hooks — The anchorage value of a r = Internal radius of the bend, and
standard U-type hook shall be equal to @ = Size of the bar or, in bundle, the size of bar
16 times the diameter of the bar. of equivalent area.
25,2.2.2 Anchoring bars in compression
For limit >~t$ method of design, this stress shall not
The anchorage length of straight bar in compression 1.J J&
exceed where fC~ is the characteristic cube
shall be equal to the development length of bars in l+2@/a
compression as specified in 25.2.1. The projected strength of concrete and a, for a particular bar or group
length of hooks, bends and straight lengths beyond of bars in contact shall be taken as the centre to centre
bends if provided for a bar in compression, shall only distance between bars or groups of bars perpendicular
be considered for development length. to the plane of the bend; for a bar or group of bars
adjacent to the face of the member a shall be taken as
25.2.2.3 Mechanical devices for anchorage the cover plus size of bar (@). For working stress
Any mechanical or other device capable of developing method of design, the bearing stress shall not exceed
f.,
the strength of the bar without damage to concrete may
1+~/a”
be used as anchorage with the approval of the engineer-
in-charge. 25.2.2.6 If a change in direction of tension or
compression reinforcement induces a resultant force
25.2.2.4 Anchoring shear reinforcement
acting outward tending to split the concrete, such
a) Inclined bars — The development length shall force should be taken up by additional links or

38 NATIONAL BUILDING CODE OF INDIA


stirrups. Bent tension bar at a re-entrant angle should
be avoided.
25.2.3 Curtailment of Tension Reinforcement in
where
Flexural Members
M, = Moment of resistance of the section
25.2.3.1 For curtailment, reinforcement shall extend
assuming all reinforcement at the section
beyond the point at which it is no longer required to
to be stressed tof~;
resist flexure for a distance equal to the effective depth
of the member or 12 times the bar diameter, whichever f, = 0,87~ in the case of limit state design and
is greater except at simple support or end of cantilever. the permissible stress a,, in the case of
In addition 25.2.3.2 to 25.2.3.5 shall also be satisfied. working stress design;
v= Shear force at the section due to design
NOTE — A point at which reinforcement is no longer required
to resist flexure is where the resistance moment of the section, loads;
considering only the continuing bars, is equal to the design LO = Sum of the anchorage beyond the centre of
moment. the support and the equivalent anchorage
25.2.3.2 Flexural reinforcement shall not be terminated value of any hook or mechanical anchorage
in a tension zone unless any one of the following at simple support; and at a point of
conditions is satisfied: inflection, LO is limited to the effective
depth of the members or 12@, whichever is
a) The shear at the cut-off point does not exceed
greater; and
two-thirds that permitted, including the shear
(p= Diameter of bar.
strength of web reinforcement provided.
b) Stirrup area in excess of that required for shear The value of M1/V in the above expression may be
and torsion is provided along each terminated increased by 30 percent when the ends of the
bar over a distance from the cut-off point reinforcement are confined by a compressive reaction.
equal to three-fourths the effective depth of 25.2.3.4 Negative moment reinforcement
the member. The excess stirrup area shall be
not less than 0.4 bslfy, where b is the breadth At least one-third of the total reinforcement provided
of beam, s is the spacing and fy is the for negative moment at the support shall extend beyond
characteristic strength of reinforcement in the point of inflection for a distance not less than the
N/mmz. The resulting spacing shall not exceed effective depth of the member of 12 @or one-sixteenth
d/8 ~~ where ~~ is the ratio of the area of bars of the clear span whichever is greater.
cut-off to the total area of bars at the section, 25.2.3.5 Curtailment of bundled bars
and d is the effective depth.
c) For 36 mm and smaller bars, the continuing Bars in a bundle shall terminate at different points
bars provide double the area required for spaced apart by not less than 40 times the bar diameter
flexure at the cut-off point and the shear does except for bundles stopping at a support.
not exceed three-fourths that permitted. 25.2.4 Special Members
25.2.3.3 Positive moment reinforcement Adequate end anchorage shall be provided for
a) At least one-third the positive moment tension reinforcement in flexural members where
reinforcement in simple members and one- reinforcement stress is not directly proportional to
fourth the positive moment reinforcement in moment, such as sloped, stepped, or tapered footings;
continuous members shall extend along the brackets; deep beams; and members in which the
same face of the member into the support, to tension reinforcement is not parallel to the compression
a length equal to L~/3. face.
b) When a flexural member is part of the primary 25.2.5 Reinforcement Splicing
lateral load resisting system, the positive
Where splices are provided in the reinforcing bars, they
reinforcement required to be extended into the
support as described in (a) shall be anchored shall as far as possible be away from the sections of
to develop its design stress in tension at the maximum stress and be staggered. It is recommended
face of the support. that splices in flexural members should not be at
sections where the bending moment is more than 50
c) At simple supports and at points of inflection,
percent of the moment of resistance; and not more than
positive moment tension reinforcement shall
half the bars shall be spliced at a section.
be limited to a diameter such that L~ computed
for f, by 25.2.1 does not exceed Where more than one-half of the bars are spliced at a

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 39


section or where splices are made at points of maximum g) In case of bundled bars, lapped splices of
stress, special precautions shall be taken such as bundled bars shall be made by splicing one
increasing the length of lap and/or using spirals or bar at a time; such individual splices within a
closely-spaced stirrups around the length of the splice. bundle shall be staggered.

25.2.5.1 Lap splices 25.2.5.2 Strength of welds

a) Lap splices shall not be used for bars larger The following values may be used where the strength
than 36 mm; for larger diameters, bars may of the weld has been proved by tests to be at least as
be welded (see 11.4); in cases where welding great as that of the parent bar.
is not practicable, lapping of bars larger than a) Splices in compression — For welded splices
36 mm may be permitted, in which case and mechanical connection, 100 percent of
additional spirals should be provided around the design strength of joined bars.
the lapped bars.
b) Splices in tension
b) Lap splices shall be considered as staggered
1) 80 percent of the design strength of welded
if the centre to centre distance of the splices
bars (100 percent if welding is strictly
is not less than 1.3 times the lap length supervised and if at any cross-section of
calculated as described in (c). the member not more than 20 percent of
c) Lap length including anchorage value of the tensile reinforcement is welded).
hooks for bars in flexural tension shall be L~ 2) 100 percent of design strength of
(see 25.2.1) or 30@ whichever is greater. The mechanical connection.
straight length of the lap shall not be less than
15@ or 200 mm. The following provisions 25.2.5.3 End-bearing splices
shall also apply:
End-bearing splices shall be used only for bars in
Where lap occurs for a tension bar located at: compression. The ends of the bars shall be square cut
1) top of a section as cast and the minimum and concentric bearing ensured by suitable devices.
cover is less than twice the diameter of
the lapped bar, the lap length shall be 25.3 Spacing of Reinforcement
increased by a factor of 1.4. 25.3.1 For the purpose of this clause, the diameter of
2) corner of a section and the minimum a round bar shall be its nominal diameter, and in the
cover to either face is less than twice the case of bars which are not round or in the case of
diameter of the lapped bar or where the deformed bars or crimped bars, the diameter shall be
clear distance between adjacent laps is taken as the diameter of a circle giving an equivalent
less than 75 mm or 6 times the diameter effective area. Where spacing limitations and minimum
of lapped bar, whichever is greater, the concrete cover (see 25.4) are based on bar diameter, a
lap length should be increased by a factor group of bars bundled in contact shall be treated as a
of 1.4. single bar of diameter derived from the total equivalent
Where both conditions (1) and (2) apply, area.
the lap length should be increased by a
25.3.2 Minimum Distance Between Individual Bars
factor of 2.0.
NOTE: Splices in tension members shall be The following shall apply for spacing of bars:
enclosed in spirals made of bars not less than 6 mm
diameter with pitch not more than 100 mm.
a) The horizontal distance between two parallel
main reinforcing bars shall usually be not less
d) The lap length in compression shall be equal
than the greatespof the following:
to the development length in compression,
1) The diameter of the bar if the diameters
calculated as described in 25.2.1, but not less
are equal,
than 24@.
2) The diameter of the larger bar if the
e) When bars of two different diameters are to
diameters are unequal, and
be spliced, the lap length shall be calculated
on the basis of diameter of the smaller bar. 3) 5 mm more than the nominal maximum
size of coarse aggregate.
f) When splicing of welded wire fabric is to be
carried out, lap splices of wires shall be made NOTE — T& does not preclude the use of larger
size of aggregates beyond the congested
so that overlap measured between the extreme
reinforcement in the same membeq the size of
cross wires shall be not less than the spacing aggregates may be reduced around congested
of cross wires plus 100 mm. reinforcement to comply wittr this provision.

40 NATIONAL BUILDING CODE OF INDIA


T--

b) Greater horizontal distance than the minimum shrinkage and temperature shall not be
specified in (a) should be provided wherever more than five times the effective depth
possible. However, when needle vibrators are of a solid slab or 450 mm whichever is
used the horizontal distance between bars of smaller.
a group may be reduced to two-thirds
the nominal maximum size of the coarse 25.4 Nominal Cover to Reinforcement
aggregate, provided that sufficient space is left 25.4.1 Nominal Cover
between groups of bars to enable the vibrator
to be immersed. Nominal cover is the design depth of concrete cover
to all steel reinforcements, including links. It is the
c) Where there are two or more rows of bars,
dimension used in design and indicated in the drawings.
the bars shall be vertically in line and the
It shall be not less than the diameter of the bar.
minimum vertical distance between the bars
shall be 15 mm, two-thirds the nominal
25.4.2 Nominal Cover to Meet Durability Requirement
maximum size of aggregate or the maximum
size of bars, whichever is greater. Minimum values for the nominal cover of normal-
weight aggregate concrete which should be provided
25.3.3 Maximum Distance Between Bars in Tension to all reinforcement, including links depending on the
Unless the calculation of crack widths shows that a condition of exposure described in 7.2.2 shall be as
greater spacing is acceptable, the following rules shall given in Table 16.
be applied to flexural members in normal internal or 25.4.2.1 However for a longitudinal reinforcing bar
external conditions of exposure. ...
in a column nominal cover shall in any case not be
a) Beams — The horizontal distance between less than 40 mm, or less than the diameter of such bar.
parallel reinforcement bars, or groups, near In the case of columns of minimum dimension of
the tension face of a beam shall not be greater 200 mm or under, whose reinforcing bars do not exceed
than the value given in Table 15 depending 12 mm, a nominal cover of 25 mm may be used.
on the amount of re-distribution carried out 25.4.2.2 For footings minimum cover shrdl be 50 mm.
in analysis and the characteristic strength of
the reinforcement. 25.4.3 Nominal Cover to Meet Specljied Period of Fire
Resistance
Table 15 Clear Distance Between Bars
Minimum values of nominal cover of normal-weight
(Clause 25.3.3)
aggregate concrete to be provided to all reinforcement
f, “ Percentage Re-distribution to or from including links to meet specified period of fire
Section Considered resistance shall be given in Table 16A.
/ \
-30 – 15 0 +15 + 30 Table 16 Nominal Cover to Meet Durability
Clear Distance Between Bars Requirements
N/mmz mm mm mm mm mm (Clause 25.4.2)
(1) (2) (3) (4) (5) (6)
250 215 260 300 300 300 Exposure Nominal Concrete Cover in mm
not Less Than
415 125 155 180 210 235
500 105 130 150 175 195 (1) (2)

NOTE — The spacings given in table are not applicable to Mild 20


members subjected to particulsdy aggressive environments Moderate 30
unless in the calculation of the moment of resistance ~Yhas Severe 45
been limited to 300 Nhnm2 in limit state design and o,, Very Severe 50
limited to 165 N/mm*in working stress &sign. 75
Extreme

b) Slabs NOTES
1) The horizontal distance between parallel 1 For main reinforcement up to 12 mm diarnoter bar for mild
main reinforcement bars shall not be exposure the nominat cover maybe reduced by 5 MM.
more than three times the effective depth 2 Unless specified otherwise, actuat concrato+~;er should not
of solid slab or 300 mm whichever is deviate from the required nominat cover by _ o MM.
smaller. 3 For exposure condition ‘severe’ and ‘very severe’, reduction
of 5 MM may be made, where concr@e grade is M 35 and
2) The horizontal distance between parallel
above.
reinforcement bars provided against

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 41


Table 16A Nominal Cover to Meet Specified Period of Fire Resistance
(Clauses 20.4 and 25.4.3 and Fig. 1)

Fire Beams Nominal Cover

‘esistince ~
Simply Continuous Slabs Ribs columns
supported ~ ,—’—.
Simply Continuous Simply Continuous
supported supported
h mm mm mm mm mm mm mm
(1) (2) (3) (4) (5) (6) (7) (8)

0.5 20 20 20 20 20 20 40
1 20 20 20 20 20 20 40
1.5 20 20 25 20 s 20 40
2 43 30 32 25 45 s 40
3 60 Q 45 z s 45 40
4 70 50 55 45 65 55 40

NOTES
1 The nominal covers given relate specifically to the minimum member dimensions given in Fig. 1.
2 Cases that lie below the bold line require attention to the additional measures necessary to reduce the risks of spalling (see 20.3.1).

25.5 Requirements of Reinforcement for two faces. The total area of such reinforcement shall
Structural Members be not less than 0.1 percent of the web area and
shall be distributed equally on two faces at a spacing
25.5.1 Beams
not exceeding 300 mm or web thickness whichever is
25.5.1.1 Tension reinforcement less.

a) Minimum reinforcement — The minimum 25.5.1.4 Transverse reinforcement in beams for shear
area of tension reinforcement shall be not less and torsion
than that given by the following:
The transverse reinforcement in beams shall be taken
~ 0.85 around the outer-most tension and compression bars.
—= —
In T-beams and I-beams, such reinforcement shall pass
bd f,
around longitudinal bars located close to the outer face
where of the flange.
A, = Minimum area of tension reinforcement, 25.5.1.5 Maximum spacing of shear reinforcement
b = Breadth of beam of the breadth of the
The maximum spacing of shear reinforcement
web of T-beam,
measured along the axis of the member shall not exceed
d= Effective depth, and
0.75 d for vertical stirrups and d for inclined stirrups
~= Characteristic strength of reinforcement at 45°, where d is the effective depth of the section
in N/mm*. under consideration. In no case shall the spacing exceed
b) Maximum reinforcement — The maximum 300 mm.
area of tension reinforcement shall not exceed
25.5.1.6 Minimum shear reinforcement
0.04 bl).
Minimum shear reinforcement in the form of stirrups
25.5.1.2 Compression reinforcement
shall be provided such that:
The maximum area of compression reinforcement shall
A
not exceed 0.04 bD. Compression reinforcement in J> 0“4
beams shall be enclosed by stirrups for effective lateral bs, - 0.87fy
restraint. The arrangement of stirrups shall be as
where
specified in 25.5.3.2.
A,v = Total cross-sectional area of stirrups legs
25.5.1.3 Side <face reinforcement effective in shear,
Where the depth of the web in a beam exceeds 750 mm, s v = Stirrup spacing along the length of the
side face reinforcement shall be provided along the member,

42 NATIONAL BUILDING CODE OF INDIA

..
b= Breadtliof the beam or breadth of the web 25.5.2.2 Maximum diameter
of flanged beam, and
The diameter of reinforcing bars shall not exceed one-
f, = Characteristic strength of the stirrup eight of the total thickness of the slab.
reinforcement in N/mmz which shall not
be taken greater than 415 N/mm*. 25.5.3 Columns

Where the maximum shear stress calculated is less than 25.5.3.1 Longitudinal reinforcement
half the permissible value and in members of minor
a) The cross-sectional area of longitudinal
structural importance such as lintels, this provision
reinforcement, shall be not less than 0.8
need not be complied with.
percent nor more than 6 percent of the gross
25.5.1.7 Distribution of torsion reinforcement cross-sectional area of the column.
NOTE — The use of 6 percent reinforcement
When a member is designed for torsion (see 40 may involve practical difficulties in placing and
or B-6) torsion reinforcement shall be provided as compacting of concrete; hence lower percentage is
below: recommended. Where bars from the columns below
have to be lapped with those in the column under
a) The transverse reinforcement for torsion consideration, the percentage of steel shall usually not
exceed 4 percent.
shall be rectangular closed stirrups placed
perpendicular to the axis of the member. The b) In any column that has a larger cross-sectional
spacing of the stirrups shall not exceed the area than that required to support the load,
the minimum percentage of steel shall be
xl + Yl
least of xl, ~ and 300 mm, where xl and based upon the area of concrete required to
y, are respectively the short and long resist the direct stress and not upon the actual
dimensions of the stirrup. area.
b) Longitudinal reinforcement shall be placed as c) The minimum number of longitudinal bars
close as is practicable to the corners of the provided in a column shall be four in
cross-section and in all cases, there shall be rectangular columns and six in circular
at least one longitudinal bar in each comer of columns.
the ties. When the cross-sectional dimension d) The bars shall not be less than 12 mm in
of the member exceeds 450 mm, additional diameter.
longitudinal bars shall be provided to satisfy e) A reinforced concrete column having helical
the requirements of minimum reinforcement reinforcement shall have at least six bars of
and spacing given in 25.5.1.3. longitudinal reinforcement within the helical
reinforcement.
25.5.1.8 Reinforcement in flanges of T-beams and
f) In a helically reinforced column, the longitudinal
L-beams shall satisfy the requirements in 22.1.l(b). bars shall be in contact with the helical
Where flanges are in tension, a part of the main tension reinforcement and equidistant around its inner
reinforcement shall be distributed over the effective circumference.
flange width or a width equal to one-tenth of the span,
whichever is smaller. If the effective flange width
a Spacing of longitudinal bars measured along
the periphery of the column shall not exceed
exceeds one-tenth of the span, nominal longitudinal
300 mm.
reinforcement shall be provided in the outer portions
h) In case of pedestals in which the longitudinal
of the flange.
reinforcement is not taken in account in
25,5.2 Slabs strength calculations, nominal longitudinal
reinforcement not less than 0.15 percent of
The rules given in 25.5.2.1 and 25.5.2.2 shall apply to the cross-sectional area shall be provided.
slabs in addition to those given in the appropriate NOTE — Pedestal is a compression member, the
clauses. effective length of which does not exceed three times
the least lateral dimension.
25.5.2.1 Minimum reinforcement
25.5.3.2 Transverse reinforcement
The mild steel reinforcement in either direction in slabs
shall not be less than 0.15 percent of the total cross- a) General — A reinforced concrete compression
sectional area. However, this value can be reduced to member shall have transverse or helical
0.12 percent when high strength deformed bars or reinforcement so disposed that every
welded wire fabric are used. longitudinal bar nearest to the compression

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 43


face has effective lateral support against i) transverse reinforcement is provided
buckling subject to provisions in (b). The for the outer-most row in accordance
effective lateral support is given by with 25.5.3.2, and
transverse reinforcement either in the form ii) no bar of the inner row is closer to
of circular rings capable of taking up the nearest compression face than
circumferential tension or by polygonal links three times the diameter of the
(lateral ties) with internal angles not largest bar in the inner row (see
exceeding 135°. The ends of the transverse Fig. 10).
reinforcement shall be properly anchored
[see 25.2.2.4 (b)].
~ 30 t~” / DIAMETER 0
b] Arrangement of transverse reinforcement
1) If the longitudinal bars are not spaced
more than 75 mm on either side, transverse
reinforcement need only to go round
corner and alternate bars for the purpose
of providing effective lateral supports
(see Fig. 8).

FIG. 10

4) Where the longitudinal bars m a


compression member are grouped (not in
I
contact) and each group adequately
tied with transverse reinforcement in
accordance with 25.5.3.2, the transverse
reinforcement for the compression
2) If the longitudinal bars spaced at a member as a whole may be provided on
distance of not exceeding 48 times the the assumption that each group is a
diameter of the tie are effectively tied in single longitudinal bar for purpose of
two directions, additional longitudinal determining the pitch and diameter of the
bars in between these bars need to be transverse reinforcement in accordance
tied in one direction by open ties (see with 25.5.3.2. The diameter of such
Fig. 9). transverse reinforcement need not,
however, exceed 20 mm (see Fig. 11).

~ TRANSVERSE
REINFORCEMENT
\
0 t~

FIG. 9

3) Where the longitudinal reinforcing bars


in a compression member are placed in
more than one row, effective lateral
support to the longitudinal bars in the GROUPS
inner rows may be assumed to have been
provided if FIG. 11

44 NATIONAL BUILDING CODE OF INDIA


c) Pitch and diameter of lateral ties 26 EXPANSION JOINTS
1) Pitch — The pitch of transverse 26.1 Structures in which marked changes in plan
reinforcement shall be not more than the dimensions take place abruptly shall be provided with
least of the following distances: expansion on joints at the section where such changes
i) The least lateral dimension of the occur. Expansion joints shall be so provided that the
compression members; necessary movement occurs with a minimum resistance
ii) Sixteen times the smallest diameter at the joint. The structures adjacent to the joint should
of the longitudinal reinforcement bar preferably be supported on separate columns or
to be tied; and walls but not necessarily on separate foundations.
Reinforcement shall not extend across an expansion
iii) 300 mm.
joint and the break between the sections shall be
2) Diameter — The diameter of the complete.
polygonal links or lateral ties shall be not
less than one-fourth of the diameter of 26.2 The details as to the length of a structure where
the largest longitudinal bar, and in no case expansion joints have to be provided can be determined
less than 6 mm. after taking into consideration various factors, such as
temperature, exposure to weather, the time and season
d) Helical reinforcement of the laying of the concrete, etc. Normally structures
1) Pitch — Helical reinforcement shall be exceeding 45 m in length are designed with one or
of regular formation with the turns of the more expansion joints. However in view of the large
helix spaced evenly and its ends shall be number of factors involved in deciding the location,
anchored properly by providing one and spacing and nature of expansion joints, the provision
a half extra turns of the spiral bar, Where of expansion joint in reinforced cement concrete
an increased load on the column on the structures should be left to the discretion of the
strength of the helical reinforcement is designer. Good practice [6-5A(41)] gives the design
allowed for, the pitch of helical turns shall considerations, which need to be examined and
be not more than 75 mm, nor more than provided for.
one-sixth of the core diameter of the
column, nor less than 25 mm, nor less SECTION 5A (d)
than three times the diameter of the steel SPECIAL DESIGN REQUIREMENTS
bar forming the helix. In other cases, FOR STRUCTURAL MEMBERS
the requirements of 25.5.3.2 shall be AND SYSTEMS
complied with.
27 CONCRETE CORBELS
2) The diameter of the helical reinforcement
shall be in accordance with 25.5.3.2 (c) 27.1 General
(2).
A corbel is a short cantilever projection which supports
25.5.3.3 In columns where longitudinal bars are offset a load bearing member and where:
at a splice, the slope of the inclined portion of the bar
a) the distance a, between the line of the reaction
with the axis of the column shall not exceed 1 in 6,
to the supported load and the root of the corbel
and the portions of the bar above and below the offset
is less than d (the effective depth of the root
shall be parallel to the axis of the column. Adequate
of the corbel); and
horizontal support at the offset bends shall be treated
as a matter of design, and shall be provided by metal b) the depth at the ovter edge of the contact area
ties, spirals, or parts of the floor construction. Metal of the supported load is not less than one-half
ties or spirals so designed shall be placed near (not of the depth at the root of the corbel.
more than eight-bar diameters from) the point of bend. The depth of the corbel at the face of the support is
The horizontal thrust to be resisted shall be assumed determined in accordance with 39.5.1.
as one and half times the horizontal components of
the nominal stress in the inclined portion of the bar. 27.2 Design
Offset bars shall be bent before they are placed in the
27.2.1 Simpllfiing Assumptions
forms. Where column faces are offset 75 mm or more,
splices of vertical bars adjacent to the offset face shall The concrete and reinforcement may be assumed to
be made by separate dowels overlapped as specified act as elements of a simple strut-and-tie system, with
in 25.2.5.1. the following guidelines:

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 45


a) The magnitude of the resistance provided to a) For simply supported beams:
horizontal force should be not less than one-
half of the design vertical load on the corbel z = 0.2 (~ i- 2D) whenl<~<2
(see also 27.2.4).
or
b) Compatibility of strains between the strut-
and-tie at the corbel root should be ensured. 1
z = 0.6 when ~ <1
It should be noted that the horizontal link requirement
described in 27.2.3 will ensure satisfactory serviceability b) For continuous beams;
performance.
Z = 0.2 (1+ 1.5D) when 1 S ~ <2.5
27.2.2 Reinforcement Anchorage
or
At the front face of the corbel, the reinforcement should
1
be anchored either by: 2=0.51 when ~ <1
a) welding to a transverse bar of equal strength
— In this case the bearing area of the load where 1 is the effective span taken as centre to
centre distance between supports or 1.15 times the
should stop short of the face of the support
clear span, whichever is smaller, and D is the
by a distance equal to the cover of the tie
overall depth.
reinforcement, or
b) bending back the bars to form a loop — 28.3 Reinforcement
In this case the bearing area of the load
28.3.1 Positive Reinforcement
should not project beyond the straight
portion of the bars forming the main tension The tensile reinforcement required to resist positive
reinforcement. bending moment in any span of a deep beam shall:

27.2.3 Shear Reinforcement a) extend without curtailment between


supports;
Shear reinforcement should be provided in the form
b) be embedded beyond the face of each support,
of horizontal links distributed in the upper two-third
of the effective depth of root of the corbel; this so that at the face of the support it shall have
reinforcement should be not less than one-half of the a development length not less than 0.8 L~;
area of the main tension reinforcement and should be where .L~is the development length (see 25.2.1),
adequately anchored. for the design stress in the reinforcement;
and
27.2.4 Resistance to Applied Horizontal Force c) be placed within a zone of depth equal to
Additional reinforcement connected to the supported 0.25 D – 0.051 adjacent to the tension face of
member should be provided to transmit this force in the beam where D is the overall depth and 1is
its entirety. the effective span.

28 DEEP BEAMS 28.3.2 Negative Reinforcement

28.1 General a) Termination of reinforcement — For tensile


reinforcement required to resist negative
a) A beam shall be deemed to be a deep beam bending moment over a support of a deep
when the ratio of effective span to overall beam:
depth, ~ is less than: 1) It shall be permissible to terminate not
more than half of the reinforcement at a
1) 2.0 for a simply supported beam; and distance of 0.5 D from the face of the
2) 2.5 for a continuous beam. support where D is as defined in 29.2
b) A deep beam complying with the requirements and
of 28.2 and 28.3 shall be deemed to satisfy 2) The remainder shall extend over the full
the provisions for shear. span.
b) Distribution — When ratio of clear span to
28.2 Lever Arm
overall depth is in the range 1.0 to 2.5, tensile
The lever arm z for a deep beam shall be determined reinforcement over a support of a deep beam
as below: shall be placed in two zones comprising:

46 NATIONALBUILD~G CODE OF INDIA


1) a zone of depth 0.2 D, adjacent to conditions; wide cracks may develop at the supports
the tension face, which shall contain and the engineer shall satisfy himself that these will
a proportion of the tension steel given not impair finishes or lead to corrosion of the
by reinforcement.

29.3 Shear

where
()
0.5 + -0.5
Where hollow blocks are used, for the purpose of
calculating shear stress, the rib width may be increased
to take account of the wall thickness of the block on
1 = Clear span, and one side of the rib; with narrow precast units, the width
D = Overall depth. of the jointing mortar or concrete may be included.
2) A zone measuring 0.3 D on either side 29.4 Deflection
of the mid-depth of the beam, which shall
contain the remainder of the tension steel, The recommendations for deflection in respect of
evenly distributed. solid slabs may be applied to ribbed, hollow block or
For span to depth ratios less than unity, voided construction. The span to effective depth ratios
the steel shall be evenly distributed over given in 22.2 for a flanged beam are applicable but
a depth of 0.8 D measured from the when calculating the final reduction factor for web
tension face. width, the rib width for hollow block slabs may be
assumed to include the walls of the blocks on both
28.3.3 Vertical Reinforcement sides of the rib. For voided slabs and slabs constructed
of box or I-section units, an effective rib width shall
If forces are applied to a deep beam in such a way that
be calculated assuming all material below the upper
hanging action is required, bars or suspension stirrups flange of the unit to be concentrated in a rectangular
shall be provided to carry all the forces concerned. rib having the same cross-sectional area and depth.

28.3.4 Side Face Reinforcement 29.5 Size and Position of Ribs


Side face reinforcement shall comply with requirements In-situ ribs shall be not less than 65 mm wide. They
of minimum reinforcement of wall (see 31.4). shall be spaced at centres not greater than 1.5 m apart
and their depth, excluding any topping, shall be not
29 RIBBED, HOLLOW BLOCK OR VOIDED
more than four times their width. Generally ribs shall
SLAB
be formed along each edge parallel to the span of one
29.1 General way slabs. When the edge is built into a wall or rests
on a beam, a rib at least as wide as the bearing shall be
This covers the slabs constructed in one of the ways
formed along the edge.
described below:
29.6 Hollow Blocks and Formers
a) As a series of concrete ribs with topping cast
on forms which may be removed after the Blocks and formers may be of any suitable material.
concrete has set; Hollow clay tiles for the filler type shall conform
b) As a series of concrete ribs between precast to accepted standard [6-5 A(42)]. When required
blocks which remain part of the completed to contribute to the structural strength of a slab they
structure; the top of the ribs maybe connected shall:
by a topping of concrete of the same strength a) be made of concrete or burnt clay; and
as that used in the ribs; and
b) have a crushing strength of at least 14 N/mmz
c) With a continuous top and bottom face but measured on the net section when axially
containing voids of rectangular, oval or other loaded in the direction of compressive stress
shape. in the slab.

29.2 Analysis of Structure 29.7 Arrangement of Reinforcement

The moments and forces due to design loads on The recommendations given in 25.3 regarding
continuous slabs may be obtained by the methods given maximum distance between bars apply to areas of solid
in Section 5A (c) for solid slabs. Alternatively, the slabs concrete in this form of construction. The curtailment,
may be designed as a series of simply supported spans anchorage and cover to reinforcement shall be as
provided they are not exposed to weather or corrosive described below:

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 47


pJ-

a) At least 50 percent of the total main 30.2 Proportioning


reinforcement shall be carried through at the
30.2.1 Thickness of Flat Slab
bottom on to the bearing and anchored in
accordance with 25.2.3.3. The thickness of the flat slab shall be generally
b) Where a slab, which is continuous over controlled by considerations of span to effective depth
supports, has been designed as simply ratios given in 22.2.
supported, reinforcement shall be provided For slabs with drops conforming to 30.2.2, span to
over the support to control cracking. This effective depth ratios given in 22.2 shall be applied
reinforcement shall have a cross-sectional directly; otherwise the span to effective depth ratios
area of not less than one-quarter that required obtained in accordance with provisions in 22.2 shall
in the middle of the adjoining spans and shall be multiplied by 0.9. For this purpose, the longer span
extend at least one-tenth of the clear span into shall be considered. The minimum thickness of slab
adjoining spans. shall be 125 mm.
c) In slabs with permanent blocks, the side cover
to the reinforcement shall not be less than 30.2.2 Drop
10 mm. In all other cases, cover shall be The drops when provided shall be rectangular in plan,
provided according to 25.4. and have a length in each direction not less than one-
third of the panel length in that direction. For exterior
29.8 Precasts Joists and HO11OWFiller Blocks
panels, the width of &ops at right angles to the non-
The construction with precast joists and hollow continuous edge and measured from the centre-line of
concrete filler blocks shall conform to good the columns shall be equal to one-half the width of
practice [6-5 A(43)] and precast joist and hollow clay drop for interior panels.
filler blocks shall conform to good practice
30.2.3 Column Heads
[6-5 A(44)].
Where column heads are provided, that portion of a
30 FLAT SLABS column head which lies within the largest right circular
30.1 General cone or pyramid that has a vertex angle of 90° and can
be included entirely within the outlines of the column
The term flat slab means a reinforced concrete slab and the column head, shall be considered for design
with or without drops, supported generally without purposes (see Fig. 12).
beams, by columns with or without flared column
heads (see Fig. 12). A flat slab may be solid slab or 30.3 Determination of Bending Moment
may have recesses formed on the soffit so that the soffit
30.3.1 Methods of Analysis and Design
comprises a series of ribs in two directions. The
recesses may be formed by removable or permanent It shall be permissible to design the slab system by
filler blocks. one of the following methods:

30.1.1 For the purpose of this clause, the following a) The direct design method as specified in 30.4,
definitions shall apply: and
b) The equivalent frame method as specified
a) Column strip — Column strip means a design
in 30.5.
strip having a width of 0.25 lZ,but not greater
than 0,2511 on each side of the column centre- In each case the applicable limitations given in 30.4
Iine, where 11 is the span in the direction and 30.5 shall be met.
moments are being determined, measured
centre-to-centre of supports and lZis the span 30.3.2 Bending Moments in Panels with Marginal
Beams or Walls
transverse to 11,measured centre-to-centre of
supports. Where the slab is supported by a marginal beam with
b) Middle strip — Middle strip means a design a depth greater than 1.5 times the thickness of the slab,
strip bounded on each of its opposite sides by or by a wall, then:
the column strip. a) the total load to be carried by the beam or
c) Panel — Panel means that part of a slab wall shall comprise those loads directly on
bounded on each of its four sides by the the wall or beam plus a uniformly distributed
centre-line of a column or centre-lines of load equal to one-quarter of the total load on
adjacent spans. the slab, and

NATIONAL BUILDING CODE OF INDIA


CRITICAL SECTION

-u- 12A SLAB WITHOUT DROP & COLUMN


WITHOUT COLUMN HEAD

CRITICAL SECTION FOR CRITICAL SECTION FOR


SHEAR ADJACENT SHEAR IMMEDIATELY
TO DROP A I ADJACENT TO COLUMN

I
1 I
-—- —-— -—-

/
/
\\ I //

12 B SLAB WITH DROP& COLUMN WITH


COLUMN HEAD

CRITICAL SECTION

Y
—.— -—-
T

ANY CONCRETE4N THIS AREA


\ /
\ / TO BE NEGLECTED IN THE
CALCULATIONS

12 C SLAB WITHOIJT DRoP & COLUMN WITH


COLUMN HEAD

NOTE— D, is the diameter of column or colurna head to be considered for desigu artd dis effective doptli of
slab or drop as appropriate.

FIG. 12 CRITICALSECTIONSFORSHEARIN FLAT SLABS

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 49


b) the bending moments on the half-column strip movement for a span shall be determined for a strip
adjacent to the beam or wall shall be one- bounded laterally by the centre-line of the panel on
quarter of the bending moments for the first each side of the centre-line of the supports.
interior column strip.
30.4.2.2 The absolute sum of the positive and average
30.3.3 Transfer of Bending Moments to Columns negative bending movements in each direction shall
be taken as:
When unbalanced gravity load, wind, earthquake, or
other lateral loads cause transfer of bending moment win
MO=—
between slab and column, the flexural stresses shall 8
be investigated using a fraction, cxof the moment given where
by: MO = Total movement;
W = Design load on an area 12l.;
in = Clear span extending from face-to-face of
columns, capitals, brackets or walls, but not
less than 0.65 1,;
where
1, = Length of span in the direction of MO; and
al = Overall dimension of the critical section for
12 = Length of span transverse to ll.
shear in the direction in which moment acts,
and 30.4.2.3 Circular supports shall be treated as square
az = Overall dimension of the critical section for supports having the same area.
shear transverse to the direction in which 30.4.2.4 When the transverse span of the panels on
moment acts. either side of the centre-line of supports varies lZshall
A slab width between lines that are one and one-half be taken as the average of the transverse spans.
slab or drop panel thickness; 1.5 D, on each side of the 30.4.2.5 When the span adjacent and parallel to an
column or capital maybe considered effective, D being edge is being considered, the distance from the edge
the size of the column. to the centre-line of the panel shall be substituted for
Concentration of reinforcement over column head by lZ in 30.4.2.2.
closer spacing or additional reinforcement maybe used 30.4.3 Negative and Positive Design Moments
to resist the moment on this section.
30.4.3.1 The negative design moment shall be located
30.4 Direct Design Method at the face of rectangular supports, circular supports
being treated as square supports having the same area.
30.4.1 Limitations
30.4.3.2 In an interior span, the total design moment
Slab system designed by the direct design method shall
MO shall be distributed in the following proportions:
fulfil the following conditions:
Negative design moment 0.65
a) There shall be minimum of three continuous
Positive design moment 0.35
spans in each direction,
b) The panels shall be rectangular, and the ratio 30.4.3.3 In an end span, the total design moment MO
of the longer span to the shorter span within shall be distributed in the following proportions:
a panel shall not be greater than 2.0,
Interior negative design moment
c) It shall be permissible to offset columns to a
maximum of 10 percent of the span in the o.75ay
direction of the offset notwithstanding the l+—
provision in (b), a,
d) The successive span lengths in each direction Positive design moment:
shall not differ by more than one-third of the
0.63-=
longer span. The end spans may be shorter
but not longer than the interior spans, and 1+~
(zC
e) The design live load shall not exceed three
Exterior negative design momerm
times the design dead load.
0.65
30.4.2 Total Design Moment for a Span
I+L
30.4.2.1 In the direct design method, the total design a=

50 NATIONAL BUILDING CODE OF INDIA


U.Cis the ratio of flexural stiffness of the exterior w;, 1; and l;, refer to the shorter span.
columns to the flexural stiffness of the slab at a joint
taken in the direction moments are being determined 30.4.6 E#ects of Pattern Loading
and is given by
In the direct design method, when the ratio of live load
#K to dead load exceeds 0.5;
K, a) the sum of the flexural stiffness of the columns
where above and below the slab, ~ KC, shall be such
K, = Sum of the flexural stiffness of the columns that a, is not less than the appropriate
meeting at the joint; and minimum value aC ~, specified in Table 17,
K, = Flexural stiffness of the slab, expressed as or
moment per unit rotation. b) if the sum of the flexural stiffnesses of the
columns, ~ Kc, does not satisfy (a), the
30.4.3.4 It shall be permissible to modify these design
moments by up to 10 percent, so long as the total design positive design moments for the panel shall
moment, MOfor the panel in the direction considered be multiplied by the coefficient ~, given by
is not less than that required by 30.4.2.2. the following equation:

30.4.3.5 The negative moment section shall be


designed to resist the larger of the two interior negative
design moments determined for the spans framing into
a common support unless an analysis is made to
distribute the unbalanced moment in accordance with 1. w,J
the stiffness of the adjoining parts. et, is the ratio of flexural stiffness of the
30.4.4 Distribution of Bending Moments Across the columns above and below the slab to the
Panel Width flexural stiffness of the slabs at a joint taken in
the direction moments are being determined
Bending moments at critical cross-section shall be and is given by:
distributed to the column strips and middle strips as
specified in 30.5.5 as applicable.
u.

30.4.5 Moments in Columns

30.4.5.1 Columns built integrally with the slab system where KC and K, are flexural stiffnesses of
shall be designed to resist moments arising from loads column and slab respectively.
on the slab system.
Table 17 Minimum Permissible Values of oj
30.4.5.2 At an interior support, the supporting (Clause 30.4.6)
members above and below the slab shall be designed
to resist the moment M given by the following equation, Imposed Load/ Ratio ~ Value of actin
in direct proportion to their stiffnesses unless a general Dead Load 1

analysis is made: (1) (2) (3)

(w; + 0.5 w,) 121:– w:l;l~ 0.5 0.5 to 2.0 0


M = 0.08 1 1.0 0.5 0.6
1+.!
1.0 0.8 0.7
(xC
1.0 1.0 0.7
where 1.0 1.25 0.8
1.0 2.0 1.2
w’,,,WI= Design dead and live loads respectively,
2.0 0.5 1.3
per unit area; 2.0 0.8 1.5
1, = Length of span transverse to the direction 2.0 1.0 1.6
of M; 2,0 1.25 1.9

1 = Length of the clear span in the direction 2.0 2.0 4.9


11
3.0 0.5 1.8
of M, measured face to face of supports;
3.0 0.8 2.0
~ Kc 3.0 1.0 2.3
a, = — where KC and K, are as defined 3.0 1.25 2.8
~ K,
3.0 2.0 13.0
in 30.4.3.3; and

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 51


30.5 Equivalent Frame Method load ratio and when all panels are not loaded
simultaneously:
30.5.1 Assumptions
a) maximum positive moment near midspan of
The bending moments and shear forces may be
a panel maybe assumed to occur when three-
determined by an analysis of the structure as a
quarters of the full design live load is on the
continuous frame and the following assumptions may
panel and on alternate panels; and
be made:
b) maximum negative moment in the slab at a
a) The structure shall be considered to be made support may be assumed to occur when three-
up of equivalent frames on column lines taken quarters of the fill design live load is on the
longitudinally and transversely through the adjacent panels only,
building. Each frame consists of a row of
30.5.2.4 In no case shall design moments be taken to
equivalent columns or supports, bounded
be less than those occurring with full design live load
laterally by the centre-line of the panel on each
on all panels.
side of the centre-line of the columns or
supports. Frames adj scent and parallel to an 30.5.3 Negative Design Moment ‘f
edge shall be bounded by the edge and the
30.5.3.1 At interior supports, the critical section for
centre-line of the adjacent panel.
negative moment, in both the column strip and middle
b) Each such frame may be analyzed in its
strip, shall be taken at the face of rectilinear supports,
entirety, or, for vertical loading, each floor .-
but in no case at a distance greater than 0.17511 from
thereof and the roof may be analyzed )
the centre of the column where 11is the length of the
separately with its columns being assumed i,
span in the direction moments are being determined,
fixed at their remote ends. Where slabs are
measured centre-to-centre of supports.
thus analyzed separately, it maybe assumed
in determining the bending moment at a given 30.5.3.2 At exterior supports provided with brackets
support that the slab is fixed at any support or capitals, the critical section for negative moment
two panels distant therefrom provided the slab in the direction perpendicular to the edge shall be
continuous beyond the point. taken at a distance from the face of the supporting
element not greater than one-half the projection of
c) For the purpose of determining relative
the bracket or capital beyond the face of the
stiffness of members, the moment of inertia
supporting element.
of any slab or column may be assumed to be
that of the gross cross-section of the concrete 30.5.3.3 Circular or regular polygon shaped supports
alone. shall be treated as square supports having the same area.
d) Variations of moment of inertia along the axis
30.5.4 Modification of Maximum Moment
of the slab on account of provision of drops
shall be taken into account. In the case of Moments determined by means of the equivalent frame
recessed or coffered slab which is made solid method, for slabs which fulfil the limitations of 30.4
in the region of the columns, the stiffening may be reduced in such proportion that the numerical
effect may be ignored provided the solid part sum of the positive and average negative moments is
of the slab does not extend more than 0.15 l,P not less than the value of total design moment MO
into the span measured from the centre-line specified in 30.4.2.2.
of the columns. The stiffening effect of flared
30.5.5 Distribution of Bending Moment Across the
column heads may be ignored.
Panel Width
30.5.2 Loading Pattern 30.5.5.1 Column strip: Negative moment at an interior
support
30.5.2.1 When the loading pattern is known, the
structure shall be analyzed for the load concerned. At an interior support, the column strip shall be
designed to resist 75 percent of the total negative
30.5.2.2 When the live load is variable but does not
moment in the panel at that support.
exceed three-quarters of the dead load, or the nature
of the live load is such that all panels will be Ioad.ed 30.5.5.2 Column strip: Negative moment at a exterior
simultaneously, the maximum moments may be support
assumed to occur at all sections when full design live
a) At an exterior support, the column strip shall
load is on the entire slab system.
be designed to resist the total negative
30.5.2.3 For other conditions of live load/dead moment in the panel at that support.

52 NATIONAL BUILDING CODE OF INDIA


b) Where the exterior support consists of a 30.6.2 Calculation of Shear Stress
column or a wall extending for a distance
The shear stress ~v shall be the sum of the values
equal to or greater than three-quarters of the
calculated according to 30.6.2.1 and 30.6.2.2.
value of lZ, the length of span transverse to
the direction moments are being determined, 30.6.2.1 The nominal shear stress in flat slabs shall
the exterior negative moment shall be be taken as V/bOd where V is the shear force due to
considered to be uniformly distributed across design load, bOis the periphery of the critical section
the length lZ. and d is the effective depth.

30.5.5.3 Column strip: Positive moment for each span 30.6.2.2 When unbalanced gravity load, wind,
earthquake or other forces cause transfer of bending
For each span, the column strip shall be designed to
moment between slab and column, a fraction (1 – LX)
resist 60 percent of the total positive moment in the
of the moment shall be considered transferred by
panel.
eccentricity of the shear about the centroid of the
30.5.5.4 Moments in the middle strip critical section. Shear stresses shall be taken as varying
linearly about the centroid of the critical section. The
The middle strip shall be designed on the following
value of a shall be obtained from the equation given
bases:
in 30.3.3.
a) That portion of the design moment not resisted
by the column strip shall be assigned to the 30,6.3 Permissible Shear Stress
adjacent middle strips. 30.6.3.1 When shear reinforcement is not provided,
b) Each middle strip shall be proportioned to the calculated shear stress at the critical section shall
resist the sum of the moments assigned to its not exceed k, ~,,
two half middle strips.
where
c) The middle strip adjacent and parallel to
an edge supported by a wall shall be k, = (0.5 + PC) but not greater than 1, PCbeing
proportioned to resist twice the moment the ratio of short side to long side of the
assigned to half the middle strip column/capital; and
corresponding to the first row of interior ZC = ().25 @ in limit state method of design,
columns.
and 0.16 & in working stress method of
30.6 Shear in Flat Slab design.
30.6.1 The critical section for shear shall be at a
30.6.3.2 When the shear stress at the critical section
distance d/2 from the periphery of the cohu-rm/capital/
exceeds the value given in 30.6.3.1, but less than 1.5 ~C
drop panel, perpendicular to the plane of the slab where
shear reinforcement shall be provided. If the shear
d is the effective depth of the section (see Fig. 12).
stress 1.5 ~C, the flat slab shall be redesigned. Shear
The shape in plan is geometrically similar to the support
stresses shall be investigated at successive sections
immediately below the slab (see Fig. 13A and
more distant from the support and shear reinforcement
Fig. 13B).
shall be provided up to a section where the shear stress
NOTE — For column sections with re-entrant angles, does not exceed 0.5 ~C. While designing the shear
the critical section shall be taken as indicated in Fig. 13C
and 13D. reinforcement, the shear stiess carried by the concrete
shall be assumed to be 0.5 ‘CCand reinforcement shall
30.6.1.1 In the case of columns near the free edge of carry the remaining shear. ~
a slab, the critical section shall be taken as shown ,4
in Fig. 14. 30.7 Slab Reinforcement”
30.6.1.2 When openings in flat slabs are located at a 30.7.1 Spacing
distance less than ten times the thickness of the slab
The spacing of bars in a flat slab, shall not exceed 2
from a concentrated reaction or when the openings are
times the slab thickness, except where a slab is of
located within the column strips, the critical sections
cellular or ribbed construction.
specified in 30.6.1 shall be modified so that the part of
the periphery of the critical section which is enclosed 30.7.2 Area of Reinforcement
by radial projections of the openings to the centroid of
the reaction area shall be considered ineffective When drop panels are used, the thickness of drop panel
(see Fig. 15), and openings shall not encroach upon for determination of area of reinforcement shall be the
column head. lesser of the following:

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 53


CRITICAL SUPPORT
SECTION \ SECTION I

I I
I &.. ,a, ,,*. ~*Y
./
I
I
I
:?’:‘“ “**’”:;.: “
.4. -
. ..*
I
I
I
I
I
: “++..
”..
● * --d I

I d/2

~ SUPPORT SECTION
––––––––

-h _J

d/2 L-

COLUMN / COLUMN HEAD


13B
13A
d/2 8
~ CRITICAL SUPPORT CRITICAL

/
LSECTION
———
\
SUPPORT
SECTION r
I
W(
SECTION
-—-— — —T
\
\
SECTION

/ \ I . .
/ \ 1 ““:*; : :.; \
/ .. . \
.“. .. -1 I ‘, ●i,
* *“k. -1
(

I “4,
.:”’j
::.
*::~..
:i~.~
I r‘.,
I
it
I1
‘d ●:. .*,= ) d/2 I

\;:.,.
.’A:
..“*
J/
“.;*
.’ “~ ●*
‘)

.*
-*.”
d/2

I ,.a”
P”i
●
I ‘:* .:4:. ”~ a..

I**
I
‘,
“*o’
..’”
~e””:”
“a :. :*** ,

4:
‘

--M
\ i

‘I
\ / I d/2
---- L —————.—— —————J

T *
4 ij/2 k-

13C 13D

NOTE — d is the effective depth of the flat slab/drop.

FIG. 13 CRITICALSECTIONSIN PLAN FOR SHEAR IN FLAT SLABS

FREE EDGE FREE


\ [ CORNER

I i

❑ ✻
I I
i ..
$, ,Jb
4’. b’.
.
,. . i
I . . i. ...’ ?“
,,*,* .... . I
●, CRiTICAL
I
: : “:0 :J; ;:: I SECTION
.. ... * .,
I
! :W’..:i”’ I
4 1
d/2

T
i
L -———-
-----J“ I i t

dL d/2
~:?.;;;~-~;;--;j

SECTION
14A 14 B

FIG. 14 EFFECTOF FREE EDGES ON CRITICALSECTIONFOR SHEAR

54 NATIONAL BUILDING CODE OF INDIA

..
— SUBTRACT FROM
OPENING
\ PERIPHERY
\ OPENING
CRITICAL
r CRITICAL SECTION
/ SECTION
\ L
~--’

COLUMN

--------
1.

. ...?..<..

L J
F
& 15B
b

OPENING
, 7 ~ LARGE OPENING *

r-------- i I
i 1

‘m
I .‘.:’”””-:”’
. ....!.. .’’.0.......
.: .,.-..
I
COLUMN
! “.’;.’ “’ ‘“*’ ‘s:: I
I I :.,.’“$’e::= “:”:;:
[ .....&, .. 1 *
I .’ ~ CRITICAL ; /;; ““~ ; :
I I SECTION ~
I I
L ---------- --~ \
L ------------ J CRITICAL
SECTION

15C ● REGARD OPENING AS FREE EDGE

150

FIG. 15 EFFECTOF OPENINGSON CRITICALSECTIONFOR SHEAR

a) Thickness of drop, and frames not braced against sideways and


b) Thickness of slab plus one quarter the for slabs resisting lateral loads shall be
distance between edge of drop and edge of determined by analysis but shall not be less
capital. than those prescribed in Fig. 16.

30.7.3 A4inimum Length of Reinforcement 30.7.4 Anchoring Reinforcement


a) Reinforcement in flat slabs shall have the a) All slab reinforcement perpendicular to a
minimum lengths specified in Fig. 16. Larger discontinuous edge shall have an anchorage
lengths of reinforcement shall be provided (straight, bent or otherwise anchored) past the
when required by analysis. internal face of the spandrel beam, wall or
b) Where adjacent spans are unequal, the column, of an amount:
extension of negative reinforcement beyond
1) For positive reinforcement — not less
each face of the common column shall be than 150 mm except that with fabric
based on the longer span. reinforcement having a fully welded
c) The length of reinforcement for slabs in transverse wire directly over the support,

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE


55
h
&
8(J)
6
p
MINIMUM
PERCENTAGE
M ~ WITHOUTDROPPANEL WITHDROPPANEL
<
+ OFSTEELAT
u) $i g
a SECTION

50
~ REMAINDER
i?
.$

50
* REMAINDER
*
(n t
!$
:
1 1. La~, 1.1--9-Al 150mm—,. IWI

m z
50 -------
I’
g
m
REMAINDER
If”’-<
1P.1. I

g g II

50 -, I--75 mm msx.
U2
~ REMAINDER
m Iwmm
la .,
I I/A /a H-
1
1.
I I

!r~~~ Iii
c yc
50
*
~ REMAINDER (ALL BARS) a . I
E
. . .
~ 1

g Lfui&f

m i? 50
ig REMAINDER
m
. ...... . ... . — 75 mm max
vfl .
I I I
I
1. CLEAR SPAN - I n
-J D L--CLEAR SPAN - I n D
t
FACE OF SUPPORT- FACE OF SUPPORT

EXTERIOR EXTERIOR SUPPORT


INTERIOR SUPPORT
suPPoRT -
t
(CONTINUl~ PROVIDED) (NO SLABCONTINUIW
(NO SLAB CONTINUl~)

Bar Length jiom Face of Suppoti


Minimum Length Maximum Length
~ A >
/ Y f
Mark a b c d e f 11
Length 0.141. 0.201. 0.22 in 0.30 in 0.331, 0+20 1, 0.241.

* Bent bars at exterior supports may be used if a general analysis is made.


NOTE — D is the diameter of the column and the dimension of the rectangular column in the direction under consideration.

FIG. 16 MINIMUMBENDJOINTLOCATION
ANDEXTENSION
FOR
REINFORCEMENT
INFLATSLABS

56 NATIONAL BUILDING CODE OF INDIA


it shall be permissible to reduce this 31.2 Empirical Design Method for Walls Subjected
length to one-half of the width of the to Inplane Vertical Loads
support or 50 mm, whichever is greaten
31.2.1 Braced Walls
and
Walls shall be assumed to be braced if they are laterally
2) For negative reinforcement — such that
supported by a structure in which all the following
the design stress is developed at
apply:
the internal face, in accordance with
Section 5A (c). a) Walls or vertical braced elements are arranged
in two directions so as to provide lateral
b) Where the slab is not supported by a spandrel
stability to the structure as a whole.
beam or wall, or where the slab cantilevers
beyond the support, the anchorage shall be b) Lateral forces are resisted by shear in the
obtained within the slab. planes of these walls or by braced elements.
c) Floor and roof systems are designed to
30.8 Openings in Flat Slabs transfer lateral forces.

Openings of any size maybe provided in the flat slab d) Connections between the wall and the lateral
supports are designed to resist a horizontal
if it is shown by analysis that the requirements of
force not less than
strength and serviceability are met. However, for
openings conforming to the following, no special 1) the simple static reactions to the total
applied horizontal forces at the level of “
analysis is required.
lateral supporG and
a) Openings of any size may be placed within 2) 2.5 percent of the total vertical load that
the middle half of the span in each direction, the wall is designed to carry at the level
provided the total amount of reinforcement of lateral support.
required for the panel without the opening is
31.2.2 Eccentricity of Vertical Load
maintained.
b) In the area common to two column strips, not The design of a wall shall take account of the actual
more than one-eighth of the width of strip in eccentricity of the vertical force subject to a minimum
either span shall be interrupted by the value of 0.05 t.
openings. The equivalent of reinforcement The vertical load transmitted to a wall by a
interrupted shall be added on all sides of the discontinuous concrete floor or roof shall be assumed
openings. to act at one-third the depth of the bearing area
c) In the area common to one column strip and measured from the span face of the wall. Where there is
one middle strip, not more than one-quarter an in-situ concrete floor continuous over the wall, the
of the reinforcement in either strip shall be load shall be assumed to act at the centre of the wall.
interrupted by the openings. The equivalent The resultant eccentricity of the total vertical load on
of reinforcement interrupted shall be added a braced wall at any level between horizontal lateral
on all sides of the openings. supports, shall be calculated on the assumption that
d) The shear requirements of 30.6 shall be the resultant eccentricity of all the vertical loads above
satisfied. the upper support is zero.

31 WALLS 31.2.3 Maximum E#ective Height to Thickness Ratio

31.1 General The ratio of effective height to thickness, HWJt, itshall


not exceed 30.
Reinforced concrete walls subjected to direct
h 31.2.4 Effective Height
compression or combined flexure and direct
compression should be designed in accordance The effective height of a braced wall shall be taken as
with Section 5 or Annex B provided the vertical follows:
reinforcement is provided in each face. Braced walls
a) Where restrained against rotation at both ends
subjected to only vertical compression maybe designed by
as per empirical procedure given in 31.2. The minimum
1) floors 0.75 HWor
thickness of walls shall be 100 mm.
2) intersecting walls or similar 0.75 L,
31.1.1 Guidelines or design of walls subjected to members whichever is the
horizontal and vertical loads are given in 31.3. lesser.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 57


b) Where not restrained against rotation at both t = Wall thickness,
ends by d = 0.8x LWwhere LWis the length of the wall.
1) floors 1.0 HWor
31.4.2.1 Under no circumstances shall the nominal
2) intersecting walls or similar 1.0 LI shear stress & in walls exceed 0,17 fCk in limit state
members whichever is the method and 0.12 ~C~in working stress method.
lesser.
where 31.4.3 Design Shear Strength of Concrete
HW = Unsupported height of the wall. The design shear strength of concrete in wrdls, ~CW,
L1 = Horizontal distance between centres of without shear reinforcement shall be taken as below:
lateral restraint.
a) For HW/LWs 1
31.2.5 Design Axial Strength of Wall
ZCW
= (3.0 – HWLJ ICI@
The design axial strength PUWper unit length of a braced
where KI is 0.2 in limit state method and 0.13
wall in compression may be calculated from the
in working stress method.
following equation:
b) For HWILW >1
PUW=0.3 (f- 1.2e-2ea)~~
Lesser of the values calculated from(a) above
where and from
t = Thickness of the wall, (HW /LW +1)
e = Eccentricity of load measured at right angles ‘rW = K,&
(HW/& -l)
to the plane of the wall determined in
accordance with 31.2.2, and where Kz is 0.045 in limit state method and
e a = Additional eccentricity due to slenderness 0.03 in working stress method, but ~cWshall
effect taken as H;J 2500 t. be not less than KJ &in any case where KS
is 0.15 in limit state method and 0.10 in
31.3 Walls Subjected to Combined Horizontal and
working stress method.
Vertical Forces
31.4.4 Design of Shear Reinforcement
31.3.1 When horizontal forces are in the plane of the
wall, it may be designed for vertical forces in Shear reinforcement shall be provided to carry a shear
accordance with 31.2 and for horizontal shear in equal to Vu – tCW.t(O.8 ~W). In case of working stress
accordance with 31.4. In plane bending may be method VU is replaced by V. The strength of shear
neglected in case a horizontal cross-section of the wall reinforcement shall be calculated as per 39.4 or B-5.4
is always under compression due to combined effect with A~v defined as below:
of horizontal and vertical loads.
A,v = PW (0.8 ~W) t
31.3.2 Walls subjected to horizontal forces
where PW is determined as follows:
perpendicular to the wall and for which the design axial
load does not exceed 0.04 fCkA~, shall be designed as a) For walls where HW/LW s 1, PW shall be the
slabs in accordance with the appropriate provisions lesser of the ratios of either the vertical
given in 23, where A~ is gross area of the section. reinforcement area or the horizontal
reinforcement area to the cross-sectional area
31.4 Design for Horizontal Shear of wall in the respective direction.
31.4.1 Critical Section for Shear b) For walls where HW/LW >1, PW shall be the
ratio of the horizontal reinforcement area to
The critical section for maximum shear shall be taken
the cross-sectional area of wall per vertical
at a distance from the base of 0.5 LW or 0.5 HW
metre.
whichever is less.
31.5 Minimum Requirements for Reinforcement in
31.4.2 Nominal Shear Stress
Walls
The nominal shear stress ~vW”
in walls shall be obtained
The reinforcement for walls shall be provided as below:
as follows:
a) the minimum ratio of vertical reinforcement
TVw = VUlt.d
to gross concrete area shall be:
where 1) 0.0012 for deformed bars not larger
Vu = Shear force due to design loads, than 16 mm in diameter and with a

58 NATIONAL BUILDING CODE OF INDIA


characteristic strength of 415 N/mm~ or
greater.
2) 0.0015 for other types of bars.
3) 0.0012 for welded wire fabric not larger
than 16 mm in diameter.
b) Vertical reinforcement shall be spaced not
farther apart than three times the wall
thickness nor 450 mm.
c) The minimum ratio of horizontal
reinforcement to gross concrete area shall
be:
1) 0.0020 for deformed bars not larger
x Y SPAN IN METRES
than 16 mm in diameter and with a
characteristic strength of 415 N/mm* or
<Im <Im G+)(+y
greater.
~) 0.0025 for other types of bars. clm ~lm G+)(+I
3) 0.0020 for welded wire fabric not larger
~lm <lm G+y+l
than 16 mm in diameter.
d) Horizontal reinforcement shall be spaced not I ~lfn
I ~lm I G+l+l
I
farther apart than three times the wall
thickness nor 450 mm.
FIG. 17 EFFECTIVE SPAN FOR STAIRS SUPPORTED AT
NOTE — The minimum reinforcement may not always EACH END BY LANDINGS SPANNING PARALLEL
be sufficient to provide adequate resistance to the effects
WITH THE RISERS
of shrinkage and temperature.

31.5.1 For walls having thickness more than 200 mm, 32.2 Dktribution of Loading on Stairs
the vertical and horizontal reinforcement shall be
In the case of stairs with open wells, where spans partly
provided in two grids, one near each face of the wall.
crossing at right angles occur, the load on areas
31.5.2 Vertical reinforcement need not be enclosed common to any two such spans may be taken as one-
by transverse reinforcement as given in 25.5.3.2 for half in each direction as shown in Fig. 18. Where flights
CO1umn, if the vertical reinforcement is not greater or landings are embedded into walls for a length of
than 0.01 times the gross sectional area or where the not less than 110 mm and are designed to span in the
vertical reinforcement is not required for compression. direction of the flight, a 150 mm strip maybe deducted
from the loaded area and the effective breadth of the
32 STAIRS section increased by 75 mm for purposes of design (see
32.1 Effective Span of Stairs Fig. 19).

The effective span of stairs without stringer beams shall 32.3 Depth of Section
be taken as the following horizontal distances:
The depth of section shall be taken as the minimum
a) Where supported at top and bottom risers by thickness perpendicular to the soffit of the staircase.
beams spanning parallel with the risers, the
distance centre-to-centre of beams; 33 FOOTINGS

b) Where spanning on to the edge of a landing 33.1 General


slab, which spans parallel, with the risers (see
Footings shall be designed to sustain the applied loads,
Fig. 17), a distance equal to the going of the
moments and forces and the induced reactions and to
stairs plus at each end either half the width of
ensure that any settlement which may occur shall be
the landing or one metre, whichever is
as nearly uniform as possible, and the safe bearing
smaller; and
capacity of the soil is not exceeded {see good practice
c) Where the landing slab spans in the same
[6-5A(35)] }.
direction as the stairs, they shall be considered
as acting together to form a single slab and 33.1.1 In sloped or stepped footings the effective
the span determined as the distance centre- cross-section in compression shall be limited by the
to-centre of the supporting beams or walls, area above the neutral plane, and the angle of slope or
the going being measured horizontally. depth and location of steps shall be such that the design

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 59


.
.,,

,1

f+”
/+%’

TT’f
DOWN

w
/
--w-
r THE LOAD ON AREAS
COMMON TO TWO
SYSTEMS TO BE TAKEN
AS ONE HALF IN EACH
DIRECTION

FIG. 18 LOADING ON STAIRSWITHOPEN WELLS

llomm~150mm

*fl&T,vEBRE.DTHJ

FIG. 19 LOADINGON STAIRSBUILT INTOWALLS

requirements are satisfied at every section. Sloped and 33.1.3 In the case of plain concrete pedestals, the angle
stepped footings that are designed as a unit shall be between the plane passing through the bottom edge of
constructed to assure action as a unit. the pedestal and the corresponding junction edge of
the column with pedestal and the horizontal plane (see
33.1.2 Thickness at the Edge of Footing
Fig. 20) shall be governed by the expression:
In reinforced and plain concrete footings, the thickness
at the edge shall be not less than 150 mm for footings 100 q.
on soils, nor less than 300 mm above the tops of piles
for footings on piles.
tan a g 0.9
d f.,
+1

60 NATIONAL BUILDING CODE OF INDIA

“.
a) the footing acting essentially as a wide beam,
with a potential diagonal crack extending in
Calculated maximum bearing pressure at the
a plane across the entire width; the critical
base of the pedestal in N/mmz, and
section for this condition shall be assumed as
Characteristic strength of concrete at 28 days a vertical section located from the face of the
in ,N/mm: column, pedestal or wall at a distance equal
to the effective depth of footing in case of
~ -COLUMN

I/ /
footings on soils, and at a distance equal to
k’ half the effective depth of footing for footings

/ //
PLAIN CONCRETE on piles.
I
/
I ‘f/a
/ PEDESTAL
b) Two-way action of the footing, with potential
diagonal
truncated
cracking along the surface of
cone or pyramid around the
concentrated load; in this case, the footing
shall be designed for shear in accordance with
appropriate provisions specified in 30.6.
FIG. 20
33.2.4.2 In computing the external shear on any
33.2 Moments and Forces section through a footing supported on piles, the entire
33.2.1 Inthe case of footings on piles, computation reaction from any pile of diameter DP whose centre is
for moments and shears may be based on the located DP/2 or more outside the section shall be
assumption that the reaction from any pile is assumed as producing shear on the section; the reaction
concentrated at the centre of the pile. from any pile whose centre is located Dp/2 or more
inside the section shall be assumed as producing no
33.2.2 For the purpose of computing stresses in shear on the section. For intermediate positions of the
footings which support a round or octagonal concrete pile centre, the portion of the pile reaction to be
column or pedestal, the face of the column or pedestal
assumed as producing shear on the section shall be
shall be taken as the side of a square inscribed within
based on straight line interpolation between full value
the perimeter of the round or octagonal column or
at DP/2 outside the section and zero value at DP/2 inside
pedestal.
the section.
33.2.3 Bending Moment
33.2.4.3 The critical section for checking the
33.2.3.1 The bending moment at any section shall be development length in a footing shall be assumed at
determined by passing through the section a vertical the same planes as those described for bending moment
plane which extends completely across the footing, and in 33.2.3 and also at all other vertical planes where
computing the moment of the forces acting over the abrupt changes of section occur. If reinforcement is
entire area of the footing on one side of the said plane. curtailed, the anchorage requirements shall be checked
in accordance with 25.2.3.
33.2.3.2 The greatest bending moment to be used in
the design of an isolated concrete footing which 33.3 Tensile Rehforcement
supports a column, pedestal or wall, shall be the
moment computed in the manner prescribed in 33.2.3.1 The total tensile reinforcement at any section shall
at sections located as follows: provide a moment of resistance at least equal to the
bending moment on the section calculated in
a) At the face of the column, pedestal or wall, accordance with 33.2.3.
for footings supporting a concrete column,
pedestal or wall; 33.3.1 Total tensile reinforcement shall be distributed
across the corresponding resisting section as given
b) Halfway between the centre-line and the edge
below:
of the wall, for footings under masonry walls;
and a) In one-way reinforced footing, the
c) Htilfway between the face of the column or reinforcement extending in each direction
pedestal and the edge of the gussetted base, shall be distributed uniformly across the full
for footings under gussetted bases. width of the footing;
b) In two-way reinforced square footing, the
33.2.4 Sl~ear and Bond
reinforcement extending in each direction
33.2.4.1 The shear strength of footings is governed shall be distributed uniformly across the full
by the more severe of the following two conditions: width of the footing; and

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 61


c) In two-way reinforced rectangular footing, the 33.4.3 Extended longitudinal reinforcement or dowels
reinforcement in the long direction shall be of at least 05 percent of the cross-sectionaI area of the
distributed uniformly across the full width of supported column or pedestal and a minimum of four
the footing. For reinforcement in the short bars shall be provided. Where dowels are used, their
direction, a central band equal to the width of diameter shall not exceed the diameter of the column
the footing shall be marked along the length bars by more than 3 mm.
of the footing and portion of the reinforcement
33.4.4 Column bars of diameters larger than 36 mm,
determined in accordance with the equation
in compression only can be dowelled at the footings
given below shall be uniformly distributed
with bars of smaller size of the necessary area. The
across the central band:
dowel shall extend into the column, a distance equal
Reinforcement in central band width 2 to the development length of the column bar and into
.—
Total reinforcement in short direction -p+l the footing, a distance equal to the development length
of the dowel.
where ~ is the ratio of the long side to the
short side of the footing. The remainder of the 33.5 Nominal Reinforcement
reinforcement shall be uniformly distributed
33.5.1 Minimum reinforcement and spacing shall be
in the outer portions of the footing.
as per the requirements of solid slab.
33.4 Transfer of Load at the Base of Column
33.5.2 The nominal reinforcement for concrete
The compressive stress in concrete at the base of a sections of thickness greater than 1 m shall be 360 mm2
column or pedestal shall be considered as being per metre length in each direction on each face. This
transferred by bearing to the top of the supporting provision does not supersede the requirement of
pedestal or footing. The bearing pressure on the loaded minimum tensile reinforcement based on the depth of
area shall not exceed the permissible bearing stress in the section.
direct compression multiplied by a value equal to
SECTION 5A (e) STRUCTURAL DESIGN
A,
(LIMIT STATE METHOD)
— but not greater than 2;
if 4
34 SAFETY AND SERVICEABILITY
where
REQUIREMENTS
A, = Supporting area for bearing of footing,
which in sloped or stepped footing may be 34.1 General
taken as the area of the lower base of the In the method of design based on limit state concept,
largest frustum of a pyramid or cone the structure shall be designed to withstand safely all
contained wholly within the footing and loads liable to act on it throughout its life; it shall also
having for its upper base, the area actually satisfy the serviceability requirements, such as
loaded and having side slope of one vertical limitations on deflection and cracking. The acceptable
to two horizontal; and limit for the safety and serviceability requirements
Az = Loaded area at the column base. before failure occurs is called a ‘limit state’. The aim
For working stress method of design the permissible of design is to achieve acceptable probabilities that the
structure will not become unfit for the use for which it
bearing stress on full area of concrete shall be taken
as 0.25 ~C~; for limit state method of design the is intended, that is, that it will not reach a limit state.
permissible bearing stress shall be 0.45~C~. 34.1.1 All relevant limit states shall be considered in
33.4.1 Where the permissible bearing stress on the design to ensure an adequate degree of safety and
concrete in the supporting or supported member would serviceability. In general, the structure shall be
be exceeded, reinforcement shall be provided for designed on the basis of the most critical limit state
developing the excess force, either by extending the and shall be checked for other limit states.
longitudinal bars into the supporting member, or by
34.1.2 For ensuring the above objective, the design
dowels (see 33.4.3).
should be based on characteristic values for material
33.4.2 Where transfer of force is accomplished by strengths and applied loads, which take into account
reinforcement, the development length of the the variations in the material strengths and in the loads
reinforcement shall be sufficient to transfer the to be supported. The characteristic values should be
compression or tension to the supporting member in based on statistical data if available; where such data
accordance with 25.2. are not available they should be based on experience.

62 NATIONALBUILDINGCODE OF INDIA
The ‘design values’ are derived from the characteristic 35 CHARACTERISTIC AND DESIGN VALUES
values through the use of partial safety factors, one AND PARTIAL SAFETY FACTORS
for material strengths and the other for loads. In the
35.1 Characteristic Strength of Materials
absence of special considerations these factors should
have the values given in 35 according to the material, The term ‘characteristic strength’ means that value of
the type of loading and the limit state being considered. the strength of the material below which not more than
5 percent of the test results are expected to fall. The
34.2 Limit State of Collapse characteristic strength for concrete shall be in
The limit state of collapse of the structure or part of accordance with Table 2. Until the relevant Indian
the structure could be assessed from rupture of one or Standard Specifications for reinforcing ‘steel are
more critical sections due to elastic
and from buckling modified to include the concept of characteristic
or plastic instability (including the effects of sway strength, the characteristic value shall be assumed as
where appropriate) or overturning. The resistance to the minimum yield stress/0,2 percent proof stress
bending, shear, torsion and axial loads at every section specified in the relevant Indian Standard Specifications.
shall not be less than the appropriate value at that 35.2 Characteristic Loads
section produced by the probable most unfavorable
combination of loads on the structure using the The term ‘characteristic load’ means that value of load
appropriate partial safety factors. which has a 95 percent probability of not being
exceeded during the life of the structure. Since data
34.3 Limit States of Serviceability are not available to express loads in statistical terms,
for the purpose of this Section, dead loads, imposed
34.3.1 Deflection
loads, wind loads, snow load in accordance with the
Limiting values of deflections are given in 22.2. good practice [6-5 A(33)] and seismic forces in
accordance with the good practice [6-5 A(34)] shall be
34.3.2 Cracking
assumed as the characteristic loads.
Cracking of concrete should not adversely affect the
35.3 Design Values
appearance or durability of the structure; the acceptable
limits of cracking would vary with the type of structure 35.3.1 Materials
and environment. Where specific attention is required
The design strength of the materials, ~~ is given by
to limit the designed crack width to a particular value,
crack width calculation may be done using formula
f,=;
given in Annex F.
r~
The practical objective of calculating crack width is where
merely to give guidance to the designer in making
f = Characteristic strength of the material (see
appropriate structural arrangements and in avoiding
35.1), and
gross errors in design, which might result in
y~ = Partial safety factor appropriate to the
concentration and excessive width of flexural crack.
material and the limit state being considered.
The surface width of the cracks should not, in general,
35.3.2 Loads
exceed 0.3 mm in members where cracking is not
harmful and does not have any serious adverse effects The design load, F~ is given by
upon the preservation of reinforcing steel nor upon the
durability of the structures. In members where cracking F~ =Fyf
in the tensile zone is harmfid either because they are where
exposed to the effects of the weather or continuously
exposed to moisture or in contact soil or ground F = Characteristic load (see 35.2), and
water, an upper limit of 0.2 mm is suggested for the y~ = Partial safety factor appropriate to the
maximum width of cracks. For particularly aggressive nature of loading and the limit state being
environment, such as the ‘sever’ category in Table 3, considered.
the assessed surface width of cracks should not in
35.3.3 Consequences of Attaining Limit State
general, exceed 0.1 mm.
Where the consequences of a structure attaining a limit
34.4 Other Limit States state are of a serious nature such as huge loss of life
Structures designed for unusual or special functions and disruption of the economy, higher values for yf
shall comply with any relevant additional limit state and y. than those given under 35.4.1 and 35.4.2 may
considered appropriate to that structure. be applied.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 63


r-

35.4 Partial Safety Factors a) Equilibrium between the internal forces and
the external loads is maintained.
35.4.1 Partial Safety Factor y~ for Loads
b) The ultimate moment of resistance provided
The values Yfgiven in Table 18 shall normally be used. at any section of a member is not less than 70
percent of the moment at the section obtained
Table 18 Values of Partial Safety Factor&
from an elastic maximum moment diagram
for Loads
covering all appropriate combinations of
(Clauses 17.2.3 .1,35.4.1 and B-4.3) loads.

Load Lbnit State of IJmit States of


c) The elastic moment at any section in a
Combination Collapse Serviceability member due to a particular combination of
~~ loads. shall not be reduced by more than 30
DL IL WL DL IL WL percent of the numerically largest moment
(1) (2) (3) (4) (5) (6) (7) given anywhere by the elastic maximum
.~ moments diagram for the particular member,
DL+ IL 1.5 — 1.0 1.0 “’ — covering all appropriate combination of loads.
DL+WL 1.50r — 1.5 1.0 — 1.0 At sections where the moment capacity after
d)
0.9’)
r A \ redistribution is less than that from the elastic
DL+ IL+ WL 1.2 1.0 0.8 0.8 maximum moment diagram, the following
relationship shall be satisfied:
NOTES
1 While consideringearthquakeeffects, substituteEL for WL. .-
2 For the limit statesof serviceability,the vrduesof y~givenin
this table are applicablefor short-termeffects.Whileassessing where
the long-termeffects due to creep the dead load and that part of x = Depth of neutral axis,
the live load likely to be permanent may only be considered.
d“ = Effective depth, and
11This value is to be considered when stability against OW’tUM@+ 6M = Percentage reduction in moment.
or stress reversal is critical.
e) In structures in which the structural frame
35.4.2 Partial Safety Factor y~ for Material Strength provides the lateral stability, the reduction
in moment allowed by condition given
35.4.2.1 When assessing the strength of a structure or in 36.1.1 (c) shall be restricted to 10 percent
structural member for the limit state of collapse, the for structures over 4 storeys in height.
values of partial safety factor, y~ should be taken as 1.5
for concrete and 1.15 for steel. 36.1.2 Analysis of Slabs Spanning in Two Directions
at Right Angles
NOTE — y. values are already incorporatedin the equations
and tables given in this Section for limit state design. Yield. line theory or any other acceptable method
may be used. Alternatively the provisions given in
35.4.2.2 When assessing the deflection, the material Annex D maybe followed.
properties such as modulus of elasticity should be taken
as those associated with the characteristic strength of 37 LIMIT STATE OF COLLAPSE: FLEXURE
the material.
37.1 Assumptions
36 ANALYSIS
Design for the limit state of collapse in flexure shall
36.1 -Analysis of Structure be based on the assumptions given below:

Method of analysis as in 21 shall be used. The material a) Plane sections normal to the axis remain plane
strength to be assumed shall be characteristic values after bending.
in the determination of elastic properties of members . b) The maximum strain in concrete at the
irrespective of the limit state being considered. outermost compression fibre is taken as
Redistribution of the calculated moments maybe made 0.0035 in bending.
as given in 36.1.1. c) The relationship between the compressive
stress distribution in concrete and the strain
36.1.1 Redistribution of Moments in Continuous
in concrete may be assumed to be rectangle,
Beams and Frames
trapezoid, parabola or any other shape which
The redistribution of moments may be carried out result in prediction of strength in substantial
satisfying the following conditions: agreement with the results of test. An

64 NATIONAL BUILDING CODE OF INDIA


acceptable stress strain curve is given in f,
—+ 0.002
Fig. 21. For design purposes, the compressive 1.15E,
strength of concrete in the structure shall be where
assumed to be 0.67 times the characteristic
strength. The partial safety factor y.= 1.5 shall f, = Characteristic strength of steel, and
be applied in addition to this. E, = Modulus of elasticity of steel.

NOTE— For the stress-straincurvein Fig.21the design NOTE— The limiting values of depth of neutral axis
stress blockparametersare as folIows(see Fig. 22). for different grades of steel based on the assumptions
of 37.1 are as follows:
Area of stress block = 0.36 -fC~.xu
Depth of centre of compressive force = 0.42 Xu fi Xu, dd
from the extremefibre in compression 250 0.53
where 415 0.48
fc, = Characteristiccompressive strength of concrete, 500 0.46
and
Xu= Depthof neutralaxis. The expression for obtaining the moments of resistance
for rectangular and T-Sections, based on the
assumptions of 37.1, are given in Annex G.
PARABOLIC fek
CURVE 38 LIMIT STATE OF COLLAPSE:
COMPRESSION
38.1 Assumptions
0.67 fek
In addition to the assumptions given in 37.l(a) to 37.l(e)
for flexure, the following shall be assumed:
0.67 fck If m
a) The maximum compressive strain in concrete
in axial compression is taken as 0.002.
b) The maximum compressive strain at the
highly compressed extreme fibre in concrete
0.002 0.0035 subjected to axial compression and bending
and when there is no tension on the section
STRAIN ~ shall be 0.0035 minus 0.75 times the strain
FIG. 21 STRESS-STRAIN CURVE FOR CONCRETE at the least compressed extreme fibre.

r --, ~
38.2 Minimum Eccentricity

All members in compression shall be designed for the


0.42 XII
minimum eccentricity in accordance with 24.4. Where
calculated eccentricity is larger, the minimum
0.36 fck X U eccentricity should be ignored.
xl u
38.3 Short Axially Loaded Members in Compression
H /

L~
The member shall be designed by considering
the assumptions given in 38.1 and the minimum
eccentricity. When the minimum eccentricity as

I per 24.4 does not exceed 0.05 times the lateral


dimension, the members may be designed by the
FIG. 22 STRESS BLOCK PARAMETERS following equation:

d) The tensile strength of the concrete is ignored. PU = 0.4 &~.AC + o.67jy.As.

e) The stresses in the reinforcement are derived where


from representative stress-strain curve for the
Pu = Axial load on the member,
type of steel used. Typical curves are given
in Fig. 23. For design purposes the partial & = Characteristic compressive strength of the
safety factory~, equal to 1.15 shall be applied. concrete,
A= = Area of concrete
f’) The maximum strain in the tension
reinforcement in the section at failure shall f, = Characteristic strength of the compression
not be less than: reinforcement, and

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 65


o.975fy
w .—— — ——— ——
-——— ———
fY
-—— ———
o.95fy
o.9ofy .—— — —
0.85fy ——— —

.—— — fy/1.~5
0.80fy

Es= 200000 N /mm 2


I 1111 I
u) 1111 1
u)
w 11/1 I
E
(n / 111! I

I I

.0001 P y .002 .003 .004

.0003 .001

23A COLD WORKED DEFORMED BAR

fY

Es=200000N/mm2

o
STRAIN ~

23B STEEL BAR WITH DEFINITE YIELD POINT

FIG. 23 REPRESENTATIVE
STRESS-STRAINCURVESFORREINFORCEMENT

A,C =Area of longitudinal reinforcement for 38.4.1 The ratio of the volume of helical reinforcement
columns. to the volume of the core shall not be less than
0.36 (A,/AC-l)jJ~Y
38.4 Compression Members with Helical
Reinforcement where

The strength of compression members with helical A. = Gross area of the section,
reinforcement satisfying the requirement of 38.4.1 A: = Area of the core of the helically reinforced
shall be taken as 1.05 times the strength of similar column measured to the outside diameter of
member with lateral ties. the helix,

66 NATIONAL BUILDING CODE OF INDIA


~C, = Characteristic compressive strength of the

[1
PD~2
concrete, and i!’l==~
2000 D
.f, = Characteristic strength of the helical
reinforcement but not exceeding 415 N/mmz.
~_<b~2
38.5 Members Subjected to Combined Axial Load
and Uniaxial Bending
1
“-2000
–[ b

where
A member subjected to axial force and uniaxial bending
Pu = Axial load on the member,
shall be designed on the basis of 38.1 and 38.2.
lCX= Effective length in respect of the major axis,
NOTE — The design of member subject to combined axial
load and uniaxial bending will involve lengthy calculation by l,Y = Effective length in respect of the minor axis,
trial and error. In order to overcome these difficulties D = Depth of the cross-section at right angles to
interaction diagrams may be used. These have been prepared
the major axis, and
and published by BIS in 5P 16 ‘Design aids for reinforced
concrete to IS 456’. b = Width of the member.

38.6 Members Subjected to Combined Axial Load For design of section, 38.5 or 38.6 as appropriate shall
and Biaxial Bending apply.
NOTES
The resistance of a member subjected to axial force
1 A column maybe considered braced in a given plane if lateral
and biaxial bending shall be obtained on the basis of
stability to the structure as a whole is provided by walls or
assumptions given in 38.1 and 38.2 with neutral axis bracing or buttressing designed to resist all laterat forces in that
so chosen as to satisfy the equilibrium of load and plane. It should otherwise be considered as unbraced.
moments about two axes. Alternatively such members 2 In the case of a braced column without any transverse loads
may be designed by the following equation: occurring in its height, the additional moment shall be added to
an initial moment equal to sum of 0.4 Mu, and 0.6 MU2where
MU2is the larger end moment and Mu,is the smatter end moment

[3J”+[4LJ.L0 (assumed negative if the column is bent in double curvature).


In no case shall the initial moment be less than 0.4 MUZ nor the
total moment including the initial moment be less than MU2.For
unbraced columns, the additional moment shall be added to the
where end moments.
MUX,M = Moments about x and y axes due to 3 Unbraced compression members, at any given level or storey,
UY subject to lateral load are usually constrained to deflect equally.
design loads, In such cases slenderness ratio for each column maybe taken
MUX,,Muy, = Maximum uniaxial moment capacity as the average for all columns acting in the same direction.
for an axial load of Pu, bending about 38.7.1.1 The values given by equation 38.7.1 maybe
x and y axes respectively, and a. is multiplied by the following facto~
related to PJPUZ

where

Puz = 0.45~,. AC+ 0.75J . A,C


where
For values of Pu/PuZ = 0.2 to 0.8, the values of et, vary
Iinerly from 1.0 to 2.0. For values less than 0.2 an is Pu = Axial load on compression member,
1.0; for values greater than 0.8, rx” is 2.0. PUZ= As defined in 38.6, and
P, = Axial load corresponding to the condition
38.7 Slender Compression Members
of maximum compressive strain of 0.0035
The design of slender compression members in concrete and tensile strain of 0.002 in
(see 24,1.1) shall be based on the forces and the outer most layer of tension steel.
moments determined from an analysis of the structure,
39 LIMIT STATE OF COLLAPSE: SHEAR
including the effect of deflections on moments and
forces. When the effect of deflections are not taken 39.1 Nominal Shear Stress
into account in the analysis, additional moment given
The nominal shear stress in beams of uniform depth
in 38.7.1 shall be taken into account in the appropriate
shall be obtained by the following equation.
direction.
v
38.7.1 The additional moments M,X and M,Y shall be q=>
calculated by the following formulae: bd

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 67


‘i
.

where 39.2.1.1 For solid slabs, the design shear strength for
VU = Shear force due to design loads; concrete shall be ~Ck, where k has the values given
below:
b = Breadth of the member, which for flanged
section shall be taken as the breadth of the
Overall 300 275 250 225 200 175 150
web, bW;and
Depth of or or
d = Effective depth. Slab, mm more less
39.1.1 Beams of Varying Depth k 1.00 1.05 1.10 1.15 1.20 1.25 1.30
In the case of beams of varying depth the equation
NOTE — This provision shafl not apply to flat slabs for which
shall be modified as: 30.6 shafl apply

39.2.2 Shear Strength of Members under Axial


Compression

For members subjected to axial compression Pu, the


where design shear strength of concrete, given in Table 19,
~v, Vu, b and d are the same as in 39.1, shall be multiplied by the following factor:
Mu = Bending moment at the section, and
(5=1+= but not exceeding 1.5
P = Angle between the top and the bottom edges ~f.
of the beam.
where i,-
The negative sign in the formula applies when the
bending moment Mu increases numerically in the same Pu = Axial compressive force in Newtons,
direction as the effective depth d increases, and the A~ = Gross area of the concrete section in rnmz,
positive sign when the moment deceases numerically and
in this direction. & = Characteristic compressive strength of
concrete.
39.2 Design Shear Strength of Concrete
39.2.3 With Shear Reinforcement
39.2.1 The design shear strength of concrete in beams
without shear reinforcement is given in Table 19. Under no circumstances, even with shear reinforcement,

Table 19 Design Shear Strength of Concrete, ‘rC,N/mmz


(Clauses 39.2.1,39.2.2,39.3,39.4, 39.5.3,40.3 .2,40.3.3 and 40.4.3)

Concrete Code
100+
-
M 15 M 20 M 25 M 30 M 35 M 40 and above
(1) (2) (3) (4) (5) (6) (7)

<0.15 0.28 0.28 0.29 0.29 0.29 0.30


0.25 0.35 0.36 0.36 0.37 0.37 0.38
0.50 0.46 0.48 0.49 0.50 / 0.50 0.51
0.75 0.54 0.56 0.57 0.59 0.59 0.60
1.00 0.60 0.62 0.64 0.66 0.67 0.68
1.25 0.64 0.67 0.70 0.71 ,4.73 0.74
1.50 0.68 0.72 0.74 0.76 0.78 0.79
1.75 0.71 0.75 0.78 0.80 0.82 0.84
2.00 0.71 0.79 0.82 0.84 0.86 0.88
2.25 0.71 0.81 0.85 0.88 0.90 0.92
2.50 0.71 0,82 0.88 0.91 0.93 0.95
2.75’ 0.71 0.82 0.90 0.94 0,% 0.98
3.00 0.71 0.82 0.92 o.% 0,99 1.01
and above

NOTE — The term As is the area of longitudinal tension reinforcement which continue~ at least one effective depth beyond the
sectionbeing considered except at support where the full area of tension reinforcement maybe used ptuvided the &Udlhtg COnfOnnS
to 25.2.2 and 25.2.3.

68 NATIONAL BUJLDING CODE OF INDIA


shall be nominal shear stress in beams ~vexceed ‘tc max 7, = Design shear strength of the concrete,
given in Table 20. b = Breadth of the member which for flanged
beams, shall be taken as the breadth of the
39.2.3.1 For solid slabs, the nominal shear stress shall
not exceed half the appropriate values given in web bW,
Table 20. f, = Characteristic strength of the stirrup or bent-
up reinforcement which shall not be taken
Table 20 Maximum Shear Stress, ~C~,X, N/mm* greater than 415 N/mmz,
(Clauses 39.2.3,39 .2.3.1,39.5.1 and 40.3.1) a = Angle between the inclined stirrup or bent-
up bar and the axis of the member, not less
Concrete M 15 M 20 M 25 M 30 M 35 M 40 and than 45°, and
Grade above
d = Effective depth.
Tcmax , 2.5 2.8 3.1 3.5 3.7 4.0
N/mmz NOTES
1 Where more than one type of shear reinforcement is used
39.3 Minimum Shear Reinforcement to reinforce the same portion of the beam, the total shear
resistance shall he computed as the sum of the resistance for
When z, is less than TCgiven in Table 19, minimum the various types separately.
shear reinforcement shall be provided in accordance 2 The area of the stirrups shall not be less than the minimum
specified in 25.5.1.6.
with 25.5.1.6.
39.5 Enhanced Shear Strength of Sections Close to
39.4 Design of Shear Reinforcement
Supports
When z, exceeds TC given in Table 19, shear
39.5.1 General
reinforcement shall be provided in any of the following
forms: Shear failure at sections of beams and cantilevers
without shear reinforcement will normally occur on
a) Vertical stirrups,
plane inclined at an angle 30° to the horizontal. If the
b) Bent-up bars along with stirrups, and angle of failure plane is forced to be inclined more
c) Inclined stirrups steeply than this [because the section considered
(X -X) in Fig. 24 is close to a support or for other
Where bent-up bars are provided, their contribution
reasons], the shear force required to produce failure is
towards shear resistance shall not be more than half
increased.
that of the total shear reinforcement.
The enhancement of shear strength maybe taken into
Shear reinforcement shall be provided to carry a shear
account in the design of sections near a support by
equal to Vu –zCbd. The strength of shear reinforcement
increasing design shear strength of concrete
VU,shall be calculated as below:
to 2d ~C/avprovided that design shear stress at the face
a) For vertical stirrups: of the support remains less than the values given in
Table 20. Account may be taken of the enhancement
0.87 fYA,vd
vu, = in any situation here the section considered is closer
s, to the face of a support or concentrated load than twice
the effective depth, d. To be effective, tension
b) For inclined stirrups or a series of bars bent-
reinforcement should extend on each side of the point
up at different cross-sections:
where it is intersected by a possible failure plane for a
0.87 fy~vd distance at least equal to ~e effective depth, or be
vu, = (smcx + coscz)
s, provided with an eqttivalent.anchorage.

c) For single bar or single group of parallel bars, 39.5.2 Shear Reinforcement for Sections Close to
all bent-up at the same cross-section: Supports
Vu, = 0.87 fY A,v sin a If shear reinforcement is required, the total area of this
is given by
where
A,, = Total cross-sectional area of stirrup legs or A,= a,b(~, -2 d~C/av)10.87~ >0.4 avb10.87fY
bent-up bars within a distance s,, This reinforcement should be provided within the
Sv = Spacing of the stirrups or bent-up bars along middle three quarters of aV, where a, is less than d,
with the length of the member, horizontal shear reinforcement will be effective than
Tv = Nominal shear stress, vertical.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 69


x

._LLLull

~av--+
x
NOTE — The shear causing failure is that acting on Section x-x,

FIG. 24 SHEARFAILURENEAR SUPPORTS

39.5.3 Enhanced Shear Strength Near Supports 40.1.1 The design rules laid down in 40.3 and 40.4
(SimplfiedApproach) shall apply to beams of solid rectangular cross-section.
However, these clauses may also be applied to flanged
The procedure given in 39.5.1 and 39.5.2maybe used
beams, by substituting bw for bin which case they are
for all beams. However for beams carrying generally
generally conservative; therefore specialist literature
uniform load or where the principal load is located
may be referred to.
farther than 2d from the face of support, the shear stress
may be calculated at a section a distance d from the 40.2 Critical Section
face of support. The value of ZC is calculated in
accordance with Table 19 and appropriate shear Sections located less than a distanced, from the face
reinforcement is provided at sections closer to the of the support may be designed for the same torsion
support, no further check for shear at such sections is as computed at a distance d, where d is the effective
required. depth.

40 LIMIT STATE OF COLLAPSE: TORSION 40.3 Shear and Torsion

40.1 General 40.3.1 Equivalent Shear

In structures, where torsion is required to maintain Equivalent shear V., shall be calculated from the
equilibrium, members shall be designed for torsion in formula:
accordance with 40.2 to 40.4. However, for such
indeterminate structures where torsion can be V,= VU+l.6;
eliminated by releasing redundant restraints, no specific
design for torsion is necessary, provided torsional where
stiffness is neglected in the calculation of internal Ve = Equivalent shear,
forces. Adequate control of any torsional cracking is
vu = Shear,
provided by the shear reinforcement as per 39.
Tu = Torsional moment, and
NOTE— The approach to design in this clause is as follows:
b = Breadth of beam.
Torsional reinforcement is not calculated separately from that
required for bending and shear. Instead the total longitudinal The equivalent nominal shear stress ~v~ in this case
reinforcement is determined for a fictitious bending moment
shall be calculated as given in 40.1, except for
which is a function of actual bending moment and torsion;
similarly web reinforcement is determined for a fictitious shear substituting VUby V~.The values of ~v~shall not exceed
which is a function of actual shear and torsion. the values of ~C~,X given in Table 20.

70 NATIONAL BUILDING CODE OF INDIA


40.3.2 If the equivalent nominal shear stress ~v~does where
not exceed ~Cgiven in Table 19, minimum shear
TU = Torsional moment,
reinforcement shall be provided as per 25.5.1.6.
vu = Shear force,
40.3.3 If ‘tV,exceeds zC given in Table 19, both s = Spacing of the stirrup reinforcement,
longitudinal and transverse reinforcement shall be
b; = Centre-to-centre distance between corner
provided in accordance with 40.4.
bars in the direction of the width,
40.4 Reinforcement in Members Subjected to dl = Centre-to-centre distance between comer
Torsion bars,

40.4.1 Reinforcement for torsion, when required, shall b = Breadth of the member,
consist of longitudinal and transverse reinforcement. ~ = Characteristic strength of the stirrup
reinforcement,
40.4.2 Longitudinal Reinforcement
T,C = Equivalent shear stress as specified
The longitudinal reinforcement shall be designed to in 40.3.1, and
resist an equivalent bending moment, M~l, given by Tc = Shear strength of the concrete as per
Me, = M“ + M, Table 19.

where 41 LIMIT STATE OF SERVICEABILITY:


MU = Bending moment at the cross-section, and DEFLECTION

~ =T (l+D/b) 41.1 Flexural Members ,m


1“
1.7 In all normal cases, the deflection of a flexural member
where will not be excessive if the ratio of its span to its
effective depth is not greater than appropriate ratios
Tu is the torsional moment, D is the overall depth
given in 22.2.1. When deflections are calculated
of the beam and b is the breadth of the beam.
according to Annex C, they shall not exceed the
40.4.2.1 If the numerical value of M, as defined permissible values given in 22.2.
in 40.4.2 exceeds the numerical value of the moment
Mu, longitudinal reinforcement shall be provided on 42 LIMIT STATE OF SERVICEABILITY:
the flexural compression face, such that the beam CRACKING
can also withstand an equivalent M~z given by 42.1 Flexural Members
M~z = M, – MU, the moment Mez being taken as acting
in the opposite sense to the moment Mu. In general, compliance with the spacing requirements
of reinforcement given in 25.3.2 should be sufficient
40.4.3 Transverse Reinforcement to control flexural cracking. If greater spacing are
required, the expected crack widti. should be checked
Two legged closed hoops enclosing the corner
by formula given in Annex F.
longitudinal bars shall have an area of cross-section
A,v, given by 42.2 Compression Members
vus,
& = Tusv Cracks due to bending in a compression member
b, dl (0.87jy) + 2.5d1 (0.87~Y) subjected to a design axial load greater than 0.2~C~AC,
where fC~is the characteristic compressive strength of
but the total transverse reinforcement shall not be less
concrete and AC is the area of the gross section of the
than
member, need not be checkqi. A member subjected to
(zve - Tc )b.sv lesser load than 0.2~& ACmay be considered as flexural
0.87fY member for the purpose of crack control (see 42.1).

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 71


ANNEX A
(Foreword)

SELF COMPACTING CONCRETE

A-1 Self compacting concrete is concrete that is A-3 CHARACTERISTICS OF FRESH SELF
able to flow under its own weight and completely COMPACTING CONCRETE
fill the formwork, even in the presence of dense The level of fluidity of self compacting concrete
reinforcement, without segregation, whilst maintaining is governed chiefly by the dosing and type of
homogeneity. superplasticizer. Due to the high fluidity of self
compacting concrete, the risk of segregation and
A-2 APPLICATION AREA
blocking is very high. Preventing segregation is
Self compacting concrete may be used in precast- therefore an important feature of the control regime.
applications or for concrete placed on site. It can be The tendency to segregation can be reduced by the
manufactured in a site batching plant or in a ready mix use of a sufficient amount of fines (e 0.125 mm), or
concrete plant and delivered to site by truck. It can using a Viscosity Modifying Admixture (VMA).
then be placed either by pumping or pouring into Features of fresh self compacting concrete
horizontal or vertical structures. In designing the mix,
the size and the form of the structure, the dimension a) Slump about 600 mm
b) Sufficient amount of frees (cO. 125 mm)
and density of reinforcement and cover should be taken
c) Use of Viscosity Modifying Admixture
in consideration.
d) Segregation resistance

ANNEX B
(Clauses 17.2,2,21 .3.1,21.7,25.2.1 and 31.1)

STRUCTURAL DESIGN (WORKING STRESS METHOD)

B-1 GENERAL concrete, under working loads, is a straight


line,
B-1.l General Design Requirements
280
The general design requirements of Section 3 shall d) The modular ratio m has the value ~
apply to this Annex. c
where a,k is permissible compressive stress due
B-1.2 Redistribution of Moments to bending in concrete in N/mmz as specified in
Except where the simplified analysis using coefficients Table 21.
(see 21.5) is used, the moments over the supports for NOTE — The expression given for m partially tafres into
any assumed arrangement of loading, including the accountlong-termeffects such as creep. Thereforethis m is
not the same as the modularratio derivedbased on the value
dead load moments may each be increased or decreased of ECgiven in 5.2.3.1.
by not more than 15 percent, provided that these
modified moments over the supports are used for the B-2 PERMISSIBLE STRESSES
calculation of the corresponding moments in the spans.
B-2.1 Permissible Stresses in Concrete
B-1.3 Assumptions for Design of Members
Permissible stresses for the various grades of concrete
In the methods based on elastic theory, the following shall be taken as those given in Tables 21 and 23.
assumptions shall be made: NOTE — For increase in strength with age 5.2.1 shall be
a) At any cross-section, plane sections before applicable.The values of permissible stress shall be obtained
by interpolationbetween the grades of concrete.
bending remain plain after bending.
b) All tensile stresses are taken up by ~inforcement B-2.1.1 Direct Tension
and none by concrete, except as otherwise For members in direct tension, when full tension is
specifically permitted. taken by the reinforcement alone, the tensile stress shall
c) The stress-strain relationship of steel and be not greater than the values given below:

72 NATIONAL BUILDING CODE OF INDIA


not exceed by more than 10 percent the value given in
Table 22.

B-2.3 Increase in Permissible Stresses


Tensile Where stresses due to wind (or earthquake) temperature
Stress, 1.22,02.8 3.2 3.64.04.44.85 .25.6
and shrinkage effects are combined with those due to
N/mm*
dead, live and impact load, the stresses specified in
F, Tables 21,22 and 23 may be exceeded up to a limit of
The tensile stress shall be calculated as 33 ~ percent. Wind and seismic forces need not be
4+m4t
considered as acting simultaneously.
where
B-3 PERMISSIBLE LOADS IN COMPRESSION
F, = Total tension on the member minus pretension MEMBERS
in steel, if any, before concreting;
B-3.1 Pedestals and Short Columns with Lateral
Ac = Cross-sectional area of concrete excluding
Ties
any finishing material and reinforcing steel;
m = Modular ratio; and The axial load P permissible on a pedestal or short
A,, = Cross-sectional area of reinforcing steel in column reinforced with longitudinal bars and lateral
tension. ties shall not exceed that given by the following
equation:
B-2.1.2 Bond Stress for Deformed Bars
P = tsCCAC+ CJ=A$C
In the case of deformed bars conforming to accepted
standard [6-5 A(40)], the bond stresses given in where
Table 21 maybe increased by 60 percent. (sW = Permissible stress in concrete in direct
compression,
Table 21 Permissible Stresses in Concrete
AC = Cross-sectional area of concrete excluding
(Clauses B-1.3, B-2.1, B-2.1.2, B-2.3 and B-4.2)
any finishing material and reinforcing steel,
Grade of PermissibleStressin PerndssibleStressin A,, = Cross-sectional area of the longitudinal steel.
Concrete Compression Bond (Average)for
~ PlainBars in Tension NOTE — The minimum eccentricity mentioned
in 24.4 maybe deemed to be incorporated in the above
o cbc (J. ‘h equation.
(1) (2) (3) (4)
B-3.2 Short Columns with Helical Reinforcement
M 10 3.0 2.5 —
M 15 5.0 4.0 0.6 The permissible load for columns with helical
M 20 7.0 5.0 0.8
M 25 8.5 6.0 0.9 reinforcement satisfying the requirement of 38.4.1
M 30 10.0 8.0 1.0 shall be 1.05 times the permissible load for similar
M 35 11.5 9.0 1.1 member with lateral ties or rings.
M 40 13.0 10.0 1.2
M 45 14.5 11.0 1.3
B-3.3 Long Columns
M 50 16.0 12.0 1.4
M 55 17.5 13.0 1.5
The maximum permissible stress in a reinforced
NOTES concrete column or part thereof having a ratio of
1 The values of permissible shear stress in concrete are given in effective column length to least lateral dimension
Table 23. above 12 shall not exceed that which results from the
2 The bond stress giveninCO14 shall be increased by 25 percent multiplication of the appropriate maximum permissible
# for b~s in compression.
stress as specified under B-2.1 and B-2.2 by the
coefficient C, given by the following formula:
B-2.2 Permissible Stresses in Steel Reinforcement
Permissible stresses in steel reinforcement shall not
C, =1.25–~
exceed the values specified in Table 22.
B-2.2.1 In flexural member the value of o,, given in where
Table 22 is applicable at the centroid of the tensile
C, = Reduction coefficient;
reinforcement subject to the condition that when more
l., = Effective length of column; and
than one layer of tensile reinforcement is provided,
the stress at the centroid of the outermost layer shall b = Least lateral dimension of column; for

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 73


Table 22 Permissible Stresses in Steel Reinforcement
(Clauses B-2.2, B-2.2. 1, B-2.3 and B-4.2)

S1 Type of Stress in Steel Reinforcement Permissible Stresses in N/mmz


No. +
/ \
Mild Steel Bars Medium Tensile High Yield Strength
Conforming to Steel Conforming to Deformed Bars
Grade 1 of IS 432 (Part 1) Conforming to IS 1786
IS 432 (Part 1) (Grade Fe 415)
(1) (2) (3) (4) (5)

i) Tension (o,, or o ,,)


a) Up to and including 20 mm 140 Half the guaranteed 230
b) Over 20 mm 130 yield stress subject to 230
a maximum of 190
ii) Compression in column bars (o J 130 130 190
iii) Compression in bars in a beam or slab when the The calculated compressive stress in the surrounding concrete
compressive resistance of the concrete is taken into multiplied by 1.5 times the modular ratio or o SCwhichever is lower
account
iv) Compression in bars in a beam or slab where the
compressive resistance of the concrete is not taken into
account:
a) Up to and including 20 mm 140 Half the guaranteed 190
b) Over 20 mm 130 yield stress subjectto 190
a maximumof 190

NOTES
1 For high yield strength deformed bars of Grade Fe 500 the permissible stress in direct tension and flexural tension shall be 0.55 ~,.
The permissible stresses for shear and compression reinforcement shall be as for Grade Fe 415.
2 For welded wire fabric conforming to accepted standard [6-5A(46)], the permissible value in tension ax is 230 N/mmz.
3 For the purpose of this Section, the yield stress of steels for which there is no clearly defined yield point should be taken to be 0.2
percent proof stress.
4 When mild steel conforming to Grade II of accepted standard [6-5A(45)] is used, the permissible stresses shall be 90 percent of the
permissible stresses in CO13, or if the design details have already been worked out on the basis of mild steel conforming to Grade 1 of
accepted standard [6-5 A(45)]; the area of reinforcement shall be increased by 10 percent of that required for Grade 1 steel.

column with helical reinforcement, b is the where


diameter of the core.
ccc = Permissible stress in concrete in direct
For more exact calculations, the maximum permissible compression;
stresses in a reinforced concrete column or part thereof AC = Net area of concrete section; which is equal
having a ratio of effective column length to least lateral to the gross area of the concrete section
radius of gyration above 40 shall not exceed those -A,C - Am;
which result from the multiplication of the appropriate A\C = Cross-sectional area of longitudinal bar
maximum permissible stresses specified under B-2.1 reinforcement;
and B-2.2 by the coefficient C~given by the following
Gmc= Allowable unit stress in metal core, not
formula:
to exceed 125 N/mm2 for a steel core, or
70 N/mm2 for a steel core, or 70 N/mm2 for
C, =1.25 –16$i
mm
a cast iron core; and
A. = Cross-sectional area of the steel or cast iron
where i~1~is the least radium of gyration.
core.
B-3.4 Composite Columns b) Metal core and reinforcement — The cross-
sectional area of the metal core shall not
a) Allowable load — The allowable axial load
exceed 20 percent of the gross area of the
P on a composite column consisting of
column. If a hollow metal core is used, it shall
structural steel or cast-iron column thoroughly
be filled with concrete. The amount of
encased in concrete reinforced with both
longitudinal and spiral reinforcement and the
longitudinal and spiral reinforcement, shall
requirements as to spacing of bars, details
not exceed that given by the following
of splices and thickness of protective
formula:
shall outside the spiral, shall conform to
P = qCAC + O,CA,C+ G~CAm requirements of 25.5.3. A clearance of at least

74 NATIONAL BUILDING CODE OF INDIA


75 mm shall be maintained between the spiral
and the metal core at all points, except that 0= CT=k
when the core consists of a structural steel
H-column, the minimum clearance may be where
reduced to 50 mm.
o cc, Cal = Calculated direct compressive stress in
c) Splices and connections of metal cores — concrete,
Metal cores in composite colttmns shall be
G= = Permissible axial compressive stress in
accurately milled at splices and positive
concrete,
provisions shall be made for alignment of one
a ~~=d = Calculated bending compressive stress in
core above another. At the column base,
concrete, and
provisions shall be make to transfer the load
to the footing at safe unit stresses in rs Cbc =“Permissible bending compressive stress
accordance with 33. The base of the metal in concrete.
section shall be designed to transfer the load b) The resultant tension in concrete is not greater
from the entire composite columns to the than 35 percent and 25 percent of the resultant
footing, or it may be designed to transfer the compression for biaxial and uniaxial bending
load from the metal section only, provided it respectively, or does not exceed three-fourths,
is placed in the pier or pedestal as to leave the 7 day modulus of rupture of concrete.
ample section of concrete above the base for
the transfer of load from the reinforced NOTES
concrete section of the column by means of 1 CTck,
@= for columns with ties where
~+l;m&
bond on the vertical reinforcement and by
P, Ac and A,c defined in B-3.1 and m is the modular
direct compression on the concrete. Transfer ratio.
of loads to the metal core shall be provided
20,,.,.. =; where M equals the moment and Z equafs
for by the use of bearing members, such as
billets, brackets or other positive connections, modulus of section. In the case of sections subject to
moments in two directions, the stress shall be calculated
these shall be provided at the top of the metal separately and added algebraically.
core and at intermediate floor levels where
required. The column as a whole shall satisfy B-4.2 Design Based on Cracked Section
the requirements of formula given under (a) If the requirements specified in B-4.1 are not satisfied,
at any point; in addition to this, the reinforced the stresses in concrete and steel shall be calculated by
concrete portion shall be designed to carry, the theory of cracked section in which the tensile
according to B-3.1 or B-3.2 as the case resistance of concrete is ignored. If the calculated
may be, all floor loads brought into the stresses are within the permissible stress specified in
column at levels between the metal brackets Tables 21, 22 and 23 the section may be assumed to
or connections. In applying the formula be safe.
under B-3.1 or B-3.2 the gross area of column
NOTE — The maximum stress in concrete and steel may be
shall be taken to be the area of the concrete
found from tables and charts based on the cracked section
section outside the metal core, and the theory or directly by determining the no-stress line which
allowable load on the reinforced concrete should satisfy the following requirements:
section shall be further limited to 0.28 f,~ times The direct load should be equal to the algebraic sum of
a)
gross sectional area of the column. the forces on concrtie and steel,
d) Allowable load on metal core only — The b) The moment of the external loads about any reference
metal core of composite columns shall be line should be eqwal to the algebraic sum of
the moment of the forces in concrete (ignoring the
designed to carry safely any construction or tensile force in concrete) and steel about the same
other loads to be placed upon them prior to line, and
their encasement in concrete. c) The moment of the external loads about any
other reference lines should be equal to the algebraic
B-4 MEMBERS SUBJECTED TO COMBINED sum of the moment of the forces in concrete (ignoring
AXIAL LOAD AND BENDING the tensile force in concrete) and steel about the
same line.
B-4.1 Design Based on Untracked Section
B-4.3 Members Subjected to Combined Direct
A member subjected to axial load and bending (due to
Load and Flexure
eccentricity of load, monolithic construction, lateral
forces, etc) shall be considered safe provided the Members subjected to combined direct load flexure
following conditions are satisfied. and shall be designed by limit state method as given

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 75


~-. I . ..-———

in 38.5 after applying appropriate load factors as given The negative sign in the formula applies when the
in Table 18. bending moment M increases numerically in the same
direction as the effective depth d increases, and the
B-5 SHEAR positive sign when the moment decreases numerically
B-5.1 Nominal Shear Stress in this direction.

The nominal shear stress Tv in beams or slabs of B-5.2 Design Shear Strength of Concrete
uniform depth shall be calculated by the following
B-5.2.1 The permissible shear stress in concrete in
equation:
beams without shear reinforcement is given in
v Table 23.
‘“”E B-5.2.1.1 For solid slabs the permissible shear stress
where
in concrete shall be kTCwhere k has the value given
V = Shear force due to design loads, below:
b = Breadth of the member, which for flanged
sections shall be taken as the breadth of the Overall 300 275 250 225 200 175 150
Depth of or or
web, and
Slab, mm more less
d = Effective depth.
k 1.00 1.05 1.10 1.15 1.20 1.25 1.30
B-5.1.1 Beams of Varying Depth

In the case of beams of varying depth, the equation NOTE — This does not apply to flat slabs for which 30.6 shatl
apply.
shall be modified as:
B-5.2.2 Shear Strength of Members Under Axial
Compression

For members subjected to axial compression P, the


where permissible shear stress in concrete ~C given in
T,, V, b and d are the same as in B-5.1. Table 23, shall be multiplied by the following facto~

M = Bending moment at the section, and


~ = Angle between the top and the bottom edges ‘ but not exceeding 1.5.
‘=l+:;.,
of the beam.

Table 23 Permissible Shear Stress in Concrete


(Clauses B-2.1, B-2.3, B-4.2, B-5.2.1, B-5.2.2, B-5.3, B-5.4, B-5.5.3, B-6.3,2,
B-6.3.3 and B-6.4.3)

PermissibleShear Stressin Concrete7@ N/mm2 Grade of Concrete


l(n)+
.
M 15 M 20 M 25 M 30 M 35 M 40 and above
(1) (2) (3) (4) (5) (6) (7)

<0.15 0.18 0.18 0.19 0.20 0.20 0.20


0.25 0.22 0.22 0.23 0.23 ‘‘ 0.23 0.23
0.50 0.29 0.30 0.31 0.31 0.31 0.32
0.75 0.34 0.35 0.36 0.37 ;~ 0.37 0,38
1.00 0.37 0.39 0.40 0.41 0.42 0.42
1.25 0.40 0.42 0.44 0.45 0.45 0.46
1.50 0.42 0.45 0.46 0.48 0.49 0.49
1.75 0.44 0.47 0.49 0.50 0.52 0.52
2.00 0.44 0.49 0.51 0.53 0.54 0.55
2.25 0.44 0.51 0.53 0.55 0s6 0.57
2.50 0.44 0.51 0.55 0.57 0.58 0.60
2.75 0.44 0.51 0.56 0.58 0.60 0.62
3.00 0.44 0.51 0.57 0.60 0.62 0.63
and above

NOTE — A, is that area of Iongitudhud tension reinforeement which continues at least one efftxtive depth beyond the section beirtg
considered except at supports where the full area of tension reinforcement may be used provided the detailing conforms to 25.2.2
and 25.2.3.

76 NATIONAL BUILDING CODE OF INDIA


where where

P = Axial compressive force in N, A,v = Total cross-sectional area of stirrup legs or


A, = Gross area of the concrete section in mmz, bent-up bars within a distance,
j’ck = Characteristic compressive strength of S, = Spacing of the stirrups or bent-up bars along
concrete. the length of the member,
T = Design shear strength of the concrete,
B-5.2.3 With Shear Reinforcement
b’ = Breadth of the member which for flanged
When shear reinforcement is provided the nominal beams, shall be taken as the breadth of the
shear stress ‘tCin beams shall not exceed ZCmu given in web bW,
Table 24. o,, = Permissible tensile stress in shear
B-5.2.3.1 For slabs, ‘cVshall not exceed half the value reinforcement which shall not be taken
of ‘c~“Id,given in Table 24. greater than 230 N/mmz,
a = Angle between the inclined stirrup or bent-
Table 24 Maximum Shear Stress ‘cC~~, N/mmz up bar and the axis of the member, not less
(Clauses B-5.2.3, B-5.2.3.1. B-5.5.1 and B-6.3.1) than 45o, and
d = Effective depth.
Concrete M15 M20 M25 M30 M35 M40and
Grade above NOTE — Where more than one type of shear reinforcement is
used to reinforce the same portion of the beam, the total shear
T. m, N/nun* 1.6 1.8 1.9 2.2 2.3 2.5 resistance shall be computed as the sum of the resistance for
the various types separately. The area of the stirrups shall not
be less than the rniaimum speeified in 25.5.1.6.
B-5.3 Minimum Shear Reinforcement
B-5.5 Enhanced Shear Strength of Sections Close
When ~v is less than ZCgiven in Table 23, minimum
to Supports
shear reinforcement shall be provided in accordance
with 25.5.1.6. B-5.5.1 General

B-5.4 Design of Shear Reinforcement Shear failure at sections of beams and cantilevers
without shear reinforcement will normally occur on
When ‘cVexceeds ‘cCgiven in Table 23, shear plane inclined at an angle 30° to the horizontal. If the
reinforcement shall be provided in any of the following angle of failure plane is forced to be inclined more
forms: steeply than this [because the section considered
a) Vertical stirrups, (X -X) in Fig. 24 is close to a support or for other
b) Bent-up bars along with stirrups, and reasons], the shear force required to produce failure is
increased.
c) Inclined stirrups.
The enhancement of shear strength maybe taken into
Where bent-up bars are provided, their contribution
account in the design of sections near a support by
towards shear resistance shall not be more than half
increasing design shear strength of concrete, ZCto 2d
that of the total shear reinforcement.
~C/avprovided that the design shear stress at the face
Shear reinforcement shall be provided to carry a shear of support remains less than the values given in
equal to V– ‘cCbd. The strength of shear reinforcement Table 24. Account may be taken of the enhancement
V, shall be calculated as beIow: in any situation where the section considered is closer
to the face of a support of concentrated load than twice
a) For vertical stirrups
the effective depth, d. To be effective, tension
reinforcement should extend on each side of the point
where it is intersected by a possible failure plane for a
distance at least equal to the effective depth, or be
b) For inclined stirrups or a series of bars bent- provided with an equivalent anchorage.
up at different cross-sections:
B-5.5.2 Shear Reinforcement for Sections Close to
Supports

If shear reinforcement is required, the total area of this


c) For single bar or single group of parallel bars, is given by:
all bent-up at the same cross-section:
A,= a, b(~v-2d~JaV)/a,v 20.4 avb10.87&

This reinforcement should be provided within the

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 77


middle three quarters of a,. Where a, is less than d, where
horizontal shear reinforcement will be more effective
V, = Equivalent shear,
than vertical.
V = Shear
B-5.5.3 Enhanced Shear Strength Near Supports T = Torsional moment, and
(Simplified Approach)
b = Breadth of beam.
Theprocedure given in B-5.5.l and B-5.5 .2 maybe
The equivalent nominal shear stress, ~,,, in this case
used for all beams. However for beams carrying
shall be calculated as given in B-5.1, except for
generally uniform load or where the principal load is
substituting V by Ve. The values of ~v~shall not exceed
located further than 2 d from the face of support, the
the values of ~Cma given in Table 24.
shear stress may be calculated at a section a distance d
from the face of support. The value of TCis calculated B-6.3.2 If the equivalent nominal shear stress ‘tV,does
in accordance with Table 23 and appropriate not exceed rc, given in Table 23, minimum shear
shear reinforcement is provided at sections closer to reinforcement shall be provided as specified
the support, no further check for such section is in 25.5.1.6.
required.
B-6.3.3 If ~ve exceeds ~Cgiven in Table 23, both
B-6 TORSION longitudinal and transverse reinforcement shall be
provided in accordance with B-6.4.
B-6.1 General

In structures where torsion is required to maintain B-6.4 Reinforcement in Members Subjected to


equilibrium, members shall be designed for torsion in Torsion
accordance with B-6.2 to B-6.4. However, for such B-6.4.1 Reinforcement for torsion, when required,
indeterminate structures where torsion can be shall consist of longitudinal and transverse
eliminated by releasing redundant restraints, no specific reinforcement.
design for torsion is necessary provided torsional
stiffness is neglected in the calculation of internal B-6.4.2 Longitudinal Reinforcement
forces. Adequate control of any torsional, cracking is
The longitudinal reinforcement shall be designed to
provided by the shear reinforcement as per B-5.
resist an equivalent bending moment, M,l, given by
NOTE — The approachto design in this clause for torsion is
as follows;
Torsionalreinforcementis not calculatedseparatelyfrom that
where
required for bending and shear. Instead the total longitudinal
reinforcementis determined for a fictitious bending moment M = Bending moment at the cross-section, and
which is a function of actual bending moment and torsion;
similarty webreinforcementis determinedfor a fictitiousshear ~ _ #l+D/b)
which is a function of actual shear and torsion. t , where T is the torsional
1.7
B-6.1.1 The design rules laid down in B-6.3 and B-6.4 moment, D is the overall depth of the beam
shall apply to beams of solid rectangular cross-section. and b is the breadth of the beam.
However, these clauses may also be applied to flanged B-6.4.2.1 If the numerical value of M, as defined
beams by substituting bWfor b, in which case they are in B-6.4.2 exceeds the numerical value of the moment
generally conservative; therefore specialist literature M, longitudinal reinforcement shall be provided on the
may be referred to.
flexural compression face, such that the beam can also
B-6.2 Critical Section withstand an equivalent moment M,z given by Mez =
M, – M, the moment M~z Being taken as acting in the
Sections located less than a distance d, from the face opposite sense to the moment M.
of the support maybe designed for the same torsion as
computed at a distance d, where d is the effective depth. B-6.4.3 Transverse Reinforcement

B-6.3 Shear and Torison Two legged closed hoops enclosing the corner
longitudinal bars shall have an area of cross-section
B-6.3.1 Equivalent Shear A,v, given by
Equivalent shear, V. shall be calculated from the
formula & - ‘ Sv : ~;d: Jbut the total transverse
b,d, 6,, . 1 Sv

V. =V+l.6: reinforcement shall not be less than

78 NATIONAL BUILDJNG CODE OF INDIA


(rye Tc) b.sv d, = Centre-to centre distance between corner
6,, bars in the direction of the depth,
b = Breadth of the member
where
o,, = Permissible tensile stress in shear
T = Torsional moment, reinforcement
V = Shear force, ‘c,, = Equivalent shear stress as specified
S, = Spacing of the stirrup reinforcement, in B-6.3.1, and
bl = Centre-to-centre distance between corner Tc = Shear strength of the concrete as specified
bars in the direction of the depth, in Table 23.

ANNEX C
(Clauses 21.3.2,22.2.1 and41.1)
CALCULATION OF DEFLECTION

C-1 TOTAL DEFLECTION bW = Breadth of web, and

C-1.l The total deflection shall be taken as the sum b = Breadth of compression face.
of the short-term deflection determined in accordance For continuous beams, deflection shall be
with C-2 and the long-term deflection, in accordance calculated using the values of Z , 1~, and M,
with C-3 and C-4. modified by the following equatio~
~
[1
=k x,+x,
C-2 SHORT-TERM DEFLECTION e 1 +(1 – kl)xo
2
C-2.1 The short-term deflection may be calculated by
where
the usual methods for elastic deflections using the
short-term modulus of elasticity of concrete, EC and Xe = Modified value of X,
an effective moment of intertia Z~ffgiven by the x,,x, = Values of X at the supports,
following equation: X. = Value of X at mid span,
k, = Coefficient given in Table 25, and
Ir x= Value of Z=, Z= or M, as appropriate.
Ieff = ; but
~2~~ ~_X bW
Mddb (1 C-3 DEFLECTION DUE TO SHRINKAGE

C-3.1 The deflection due to shrinkage aC, may be


computed from the following equation:
where

I, = Moment of inertia of the cracked section,


where
fa 1,,
M, = Cracking moment, equal to — where k, is a constant depending upon the support
Y, conditions,
i, = Modulus of rupture of concrete, 0.5 for cantilevers,
I = Moment of inertia of the gross section 0.125 for simply supported members,
w
about the centroidal axis, neglecting the
0.086 for members continuous at one end, and
reinforcement, and yt is the distance from
0.063 for fully continuous members,
centroidal axis of gross section, neglecting
the reinforcement, to extreme fibre in WC,is shrinkage curvature equal to k, ~
tension,
M = Maximum moment under service loads where EC, is the ultimate shrinkage strain of
s Lever arm, concrete (see 5.2.4),
z
x = Depth of neutral axis,
d = Effective depth,

PART 6 STRUCTUWL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 79


and D is the total depth of the section, and 1 is the
length of span.

C-4 DEFLECTION DUE TO CREEP


100 AL 100 AC C-4.1 The creep deflection due to permanent
<=— and P=—
bd bd loads aCC(P~r~)
may be obtained from the following
equation:
Table 25 Values of Coefficient, kl
a cc – a.1(pm)
(Clause C-2.1) (perm) = ai, cc (penrr)

where
k, 0,5 0,6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4
or a., ,C(F~) = Initial plus creep deflection due to
less
permanent loads obtained using an
k, O 0.03 0.08 0.16 0.30 0.50 0.73 0.91 0.97 1.0 elastic analysis with an effective
modulus of elasticity;
NOTE— k2 is given by

k = M,+M2 EC, = &, 0 being the creep coefficient;


2 M,, + Mn
and
where
M,, M, = Support moments, and
a , (Pm) = Short-term deflection due to permanent
MF1, MF2 = Fixed end moments load using EC. ..

ANNEX D
(Clauses 23.4 and 36.1.2)
SLABS SPANNING IN TWO DIRECTIONS

D-1 RESTRAINED SLABS apply only to the middle strips and no re-distribution
shall be made.
D-1.O When the corners of a slab are prevented from
lifting, the slab may be designed as specified in D-1.l D-1.4 Tension reinforcement provided at mid-span in
to D-1.11. the middle strip shall extend in the lower part of the
slab to within 0.251 of a continuous edge, or 0.151 of
D-1.l The maximum bending m~ments per unit width
a discontinuous edge.
in a slab are given by the following equations:
D-1.5 Over the continuous edges of a middle strip,
Mx = ctxwl: the tension reinforcement shall extend in the upper part
of the slab a distance of 0.151 from the support, and at
MY =cXYWl; least 50 percent shall extend a distance of 0.31.

where D-1.6 At a discontinuous edge, negative moments may


arise. They depend on the degree of fixity at the edge
a, and ctYare coefficients given in Table 26,
of the slab but, in general, tension reinforcement equal
w = Total design and load per unit area. to 50 percent of that provided at mid-span extending
M,, M = Moments on strips of unit width 0.11 into the span will be sufficient.
Y
spanning 1Xand lY respectively, and
D-1.7 Reinforcement in edge strip, parallel to that
1Xand 1, = Lengths of the shorter span and longer
edge, shall comply with the minimum given in
span respectively.
Section 3 and the requirements for torsion given
D-1.2 Slabs are considered as divided in each direction in D-1.8 to D-1.1O.
into middle strips and edge strips as shown in Fig. 25
D-1.8 Torsion reinforcement shall be provided at any
the middle strip being three-quarters of the width and
comer where the slab is simply supported on b“othedges
each edge strip one-eight of the width.
meeting at that comer. It shall consist of top and bottom
D-1.3 The maximum moments calculated as in D-1.l reinforcement, each with layers of bars placed parallel

80 NATIONAL BUILDING CODE OF INDIA


Table 26 Bending Moment Coefficients for Rectangular Panels Supported on
Four Sides with Provision for Torsion at Corners
(Clauses D-1. 1 and 23.4.1)

Case Type of Panel Short Span Coefilcients c% Long Span


No. and Moments (Values of lYIIX) Coefficients q for
Considered A All Values of
e \
1.0 1.1 1.2 1,3 1.4 1.5 1.75 2.0 l#x
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11)

Interior Panels:
Negative moment at 0.032 0.037 0.043 0.047 0.051 0.053 0.060 0.065 0.032
continuous edge
Positive moment at 0.024 0.028 0.032 0.036 0.039 0.041 0.045 0.049 0.024
mid-span
2 One Short Edge
Discontinuous:
Negative moment at 0.037 0.043 0.048 0.051 0.055 0.057 0.064 0.068 0.037
continuous edge
Positive moment at 0.028 0.032 0.036 0.039 0.041 0.044 0.048 0.052 0.028
mid-span
3 One Long Edge
Discontinuous:
Negative moment at 0.037 0.044 0.052 0.057 0.063 0.067 0.077 0.085 0.037
continuous edge
Positive moment at 0.028 0.033 0.039 0.044 0.047 0.051 0.059 0.065 0.028
mid-span
4 Two-Adjacent Edges
Discontinuous:
Negative moment at 0.047 0.053 0.060 0.065 0.071 0.075 0.084 0.091 0.047
continuous edge
Positive moment at 0.035 0.040 0.045 0.049 0.053 0.056 0.063 0.069 0.035
mid-span
5 Two Short Edges
Discontinuous:
Negative moment at 0.045 0.049 0.052 0.056 0.059 0.060 0.065 0.069 —
continuous edge
Positive moment at 0.035 0.037 0.040 0.043 0.044 0.045 0.049 0.052 0.035
mid-span
6 Two Long Edges
Discontinuous:
Negative moment at — — — — — — — — 0.045
continuous edge
Positive moment at 0.035 0.043 0.051 0.057 0.063 0.068 0.080 0.088 0.035
mid-span
7 Three Edges
Discontinuous:
(One Long Edge
Continuous)
Negative moment at 0.057 0.064 0.071 0.076 0.080 0.084 0,091 0.097 —
continuous edge
Positive moment at 0.043 0.048 0.053 0.057 0.060 0.064 0.069 0.073 0.043
mid-span
8 Yhree Edges
Discontinuous
{One Short Edge
Continuous,):
Negative moment at — — — — — — — — 0.057
continuous edge
Positive moment at 0.043 0.051 0.059 0.065 0.071 0.076 0.087 0.096 0.043
mid-span
9 Four Edges
Discontinuous:
Positive moment at 0.056 0.064 0.072 0.079 0.085 0.089 0.100 0.107 0.056
mid-span

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 81


r
lx
-—— EDGE STRIP
——— ———

MIDDLE STRIP
——- 1

L -—— ——— ———


EDGE STRIP
——.

g~$’~g

25A - FOR SPAN IX 25 B - FOR SPAN!’

FIG. 25 DIVISION OF SLAB INTO MIDDLE AND EDGE STRIPS

to the sides of the slab and extending from the edges a adequate provision to resist torsion at corners and to
minimum distance of one-fifth of the shorter span. The prevent the corners from lifting, the maximum
area of reinforcement in each of these four layers shall moments per unit width are given by the following
be three-quarters of the area required for the maximum equation:
mid-span moment in the slab.
Mx = axw 1:
D-1.9 Torsion reinforcement equal to half that
described in D-1.8 shall be provided at a corner
My =aywl:
contained by edges over only one of which the slab is
continuous. where
D-I.1O “1’orsion reinforcements need not be provided A4X,My, lY, lx are same as those in D-1.1, and
at any corner contained by edges over both of which ctXand aY are moment coefficients given in
the slab is continuous. Table 27.
D-1.11 Where ly/lx is greater than 2, the slabs shall be D-2.1.1 At least 50 percent of the tension
designed as spanning one way. reinforcement provided at mid-span should extend
to the supports. The remaining 50 percent should
D-2 SIMPLY SUPPORTED SLABS
extend to within 0.1 1Xor 0.1 lY of the support, as
D-2.1 When simply supported slabs do not have appropriate.

Table 27 Bending Moment Coefilcients for Slabs Spanning in Two Directions at


Right Angles, Simply Supported on Four Sides
(Clause D-2.1)

lxlly 1.0 1.1 1.2 1.3 1.4 1.5 1.75 2.0 2.5 3.0

ax 0.062 0.074 0.084 0.093 0.099 0.104 0.113 0.118 0.122 0.124

~Y
0.062 0.061 0.059 0.055 0.051 0.046 0.037 0.029 0.020 0.014

82 NATIONAL BUILDING CODE OF INDIA


.

ANNEX E
(Clause 25.2)
EFFECTIVE LEGNTH OF COLUMNS

E-1 Intheabsence ofmoreexact analysis, theeffective Kc


length of columns in framed structures maybe obtained Kc+ Kb
from the ratio of effective length to unsupported length where the summation is to be done for the members framing
le~l give in Fig. 26 when relative displacement of the into a joint at top and bottom respectively; and Kc and Kb being
ends of the column is prevented and in Fig. 26 when the flexural stiffness for column and beam respectively.

relative lateral displacement of the ends is not E-2 To determine whether a column is a no sway or a
prevented. In the latter case, it is recommended that sway column, stability index Q may be computed as
the effective length ratio lC/l may not be taken to be given below:
less than 1.2.
NOTES
1 Figures 26 and 27 are reproduced from ‘The Strutural
where
Engineer’ No. 7, Volume 52, July 1974 by the permission of
the Council of the Institution of Structural Engineers, U.K. Pu = Sum of axial loads on all column in the
2 In Fig. 26 and 27 ~, and ~ ~are equal to storey,

\.
HINGED 1.0
I \l l\l I I .
0.9

0.8 I 1 \ I \ I [

0.7 l\ 1 \ 1 x L>

t lx ‘b.\ % \~

0.6
N x
‘L
1 \
l\l
I w
I
N1’i’h
I lx I
0.5 I

0.4

0.3

o.2~

0.1
‘‘ ‘“”’”’
~ \“ L

l\ l\ l\ I

FiXED
0
(1 \ ().1 ().2 ().3 0.4 05 (36 0.7 0.8 0.9 1.0

$p
FIXED HINGED

FIG. 26 EFFECTIVE LENGTH RATIOS FOR A COLUMN IN A FRAME WITH NO SWAY

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 83

..
;
,,, #
.-,
.

HINGED 1.0

0.9 I

0.8

0.7

0.6

(+
0.5

0.4

0.3

0.2

0.1

?07
FIXED
o\
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 o-g 1-0

Pz
FIXED HINGED

FIG. 27 EFFECTIVELENGTHRATIOSFORA COLUMNIN A FRAME


WITHOUTRESTRAINTAGAINSTSWAY

AU = Elastically computed first order lateral If Q <0.04, then the column in the frame may be taken
deflection, as no sway column, otherwise the column will be
considered as sway column.
Hu = Total lateral force acting within the storey,
and E-3 For normal usage assuming idealized conditions,
h, = Height of the storey. the effective length 1~~of in a given plane may be
assessed on the basis of Table 28.

84 NATIONALBUILDINGCODE OF INDIA
Table 28 Effective Length of Compression Members
(Clause E-3)

Degree of End Restraint of Symbol Theoretical Value of Recommended Value of


Compression Members Effective Length Effective Length
(1) (2) (3) (4)

I
Effectively held in position and /
restrained against rotation at 0.501 0.651
both ends
I
\

Effectively held in position at


both ends, restrained against 0.701 0.801
rotation at one end

Effectively held in position at


both ends, but not restrained
against rotation
/
\ I 1.001 1.001

rl
Effectively held in position and
restrained against rotation at one
end, and at the other restrained
7 1+

/1
!
1.001 1.201
against rotation but not held in /
oosition 11
t
/////m/
1

Effectively held in position and


>:>
restrained against rotation in one 7
end, and at the other partially / — 1.501
restrained against rotation but
/’
not held in Position 1

Effectively held in position at t-l

L/
t+
one end but not restrained
against rotation, and at the other 2.001 2.001
end restrained against rotation /’
J
but not held in position /
/

Effectively held in position and

I
restrained against rotation at one i
end but not held in position nor 2.001 2.001
restrained against rotation at the /’
1
other end 7/ /
Z??Z

NOTE — 1is the unsupported length of compression member.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 85

..
~. /

ANNEX F
(Clauses 34.3.2 and 42.1)
CALCULATION OF CRACK WIDTH

Provided that the strain in the tension reinforcement is distributions, having a value of zero at the neutral axis
limited to 0.8 FY/E,, the design surface crack width, and a value at the centroid of the tension steel of
which should not exceed the appropriate value given 1 N/mm2 instantaneously, reducing to 0.55 N/mm2 in
in 34.3.2 may be calculated from the following the long-term, acting over the tension zone divided by
equation: the steel area.

Design surface crack width These assumptions are illustrated in Fig. 28,
3acrEm where
Wa=
~+z(a. –Cmn) h = Overall depth of the section,
h–x
x = Depth from the compression face to the
where neutral axis. *
a Cr = Distance from the point considered to the L = Maximum compressive stress in the concrete,
surface of the nearest longitudinal bar,
& = Tensile stress in the reinforcement, and
c mm = Minimum cover to the longitudinal bar, E, = Modulus of elasticity of the reinforcement.
Em = Average steel strain at the level considered,
For a rectangular tension zone, this gives
h = Overall depth of the member, and
x = Depth of the neutral axis. b(h–x)(a–x)
&m=&l–
3 E,AJd –X)
The average steel strain emmay be calculated on the
basis of the following assumption: where

The concrete and the steel are both considered to be A, = Area of tension reinforcement,
fully elastic in tension and in compression. The elastic b = Width of the section at the centroid of the
modulus of the steel maybe taken as 200 kN/mm2 and tension steel,
the elastic modulus of the concrete is as derived from E, = Strain at the level considered, calculated *
the equation given in 5.2.3.1 both in compression and ignoring the stiffening of the concrete in the
in tension. tension zone,
Alternatively, as an approximation, it will normally a = Distance from the compression face to the
be satisfactory to calculate the steel stress on the basis point at which the crack width is being
of a cracked section and then reduce this by an amount calculated, and
equal to the tensile force generated by the triangular d = Effective depth.

k I Ec fc

As
STRESS IN CONCRETE
I ● ●
1 N / mmz IN SHORT TERM
0.55 N/mm2 IN LONG TERM

SECTION CRACKED STRAIN STRESS

FIG. 28

86 NATIONAL BUILDING CODE OF INDIA

.
ANNEX G

(Clause 38.1)

MOMENTS OF RESISTANCE FOR RECTANGULAR AND T-SECTIONS

G-O The moments of resistance of rectangular and ~u-Mu, fire,= &CA,C(d-d’)


T-sections based on the assumption of 37.1 are given
where
in this Annex.
MU,MU ,,m,d are same as in G-1.l
G-1 RECTANGULAR SECTIONS
&c = Design stress in compression reinforcement
G-1.l Sections Without Compression Reinforcement corresponding to a strain of
The moment of resistance of rectangular sections
without compression reinforcement should be obtained 0.0035 ‘x”mX-d’)
x u, Inax
as follows:

a) Determine the depth of neutral axis from the x u, max


= Limiting value of Xufrom 37.1.
following equation: A% = Area of compression reinforcement,
and
x. _ 0.87 jy 4
d’ = Depth of compression reinforcement
T – 0.36 fck b.d
from compression face.
b) If the value of xu/d is less than the limiting
The total area of tension reinforcement shall be
value (see Note below 37.1), calculate the
obtained from the following equation:
moment of resistance by the following
expression: A,t = A,tl + A,t2

where

c)
Mu = 0.87 fy~,d
[1
l–—
‘% f,
bd f&

If the vrdue of xu/d is equal to the limiting


A,t = Area of the total tensile reinforcement,
A,tl = Area of the tensile reinforcement for a singly
reinforced section for Mu E., and
value, the moment of resistance of the section
is given by the following expression: A,t, = A,C~]0.87 f,.

1
G-2 FLANGED SECTION
Mu,li. = 0.36% l–O.42~ bd’ f=,
[ G-2.1 For XUc Dr the moment of resistance may be
d) If x,jd is greater than the limiting value, the calculated from the equation given in G-1.l.
section should be redesigned.
G-2.1 The limiting value of the moment of resistance
In the above equations, of the section may be obtained by the following
equation when the ratio Df Id does not exceed 0.2:
x = Depth of neutral axis,
d“ = Effective depth,
$
A,t
= Characteristic strength of reinforcement,
= Area of tension reinforcement,
Mu = 0.36+
[
1–0.42+
1 f&bwd2

[1
& = Characteristic compressive strength of Df
+ 0.45 f& (b~+,) D~ d –y
concrete,
b = Width of the compression face,
where
Mu.,i~= Limiting moment of resistance of a section
without compression reinforcement, and Mu, Xu -, d and ~k are same as in G-1.1,
x . ma = Limiting value of x“ from 37.1. b~ = Breadth of the compression face/fkmge,
bw = Breadth of the web,
G-1.2 Section with Compression Reinforcement
D, = Thickness of the flange.
Where the ultimate moment of resistance of section
exceeds the limiting value, Mu. ~i~ compression G-2.2.1 When the ratio Df Id exceeds 0.2,the moment
reinforcement may be obtained from the following of resistance of the section may be calculated by the
equation: following equation:

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 87


and the other symbols are same as in G-1.l
Mu = 0.36%
[
1–0.42%
1 fCkbwd2
and G-2.2.

G-2.3 For Xu - > XU> D~ the moment of resistance

where
+0.45 fCk (b~–bw) y~ d-;
[1 may be calculated by the ‘equations given in G-2.2
when D~Ixu does not exceed 0.43 and G-2.2.1 when
Df /xU exceeds 0.43; in both cases substituting Xu,-
Yf = (0.15 XU+ 0.65 D~), but not greater than D, by x..

LIST OF STANDARDS

The following list records those standards which are 1S No. Title
acceptable as ‘good practice’ and ‘accepted standards’ (Part 4): 1972 Types of concrete
in the fulfillment of the requirements of the Code. The
(Part 5): 1972 Formwork for concrete
standards listed may be used by the Authority as a guide
in conformance with the requirements of the referred (Part 6): 1972 Equipment, tool and plant
clauses in the Code. (Part 7): 1973 Mixing, laying, compaction,
curing and other construction
IS No. Title
aspect
(1) 3370 Code of practice for concrete
(Part 8): 1973 Properties of concrete
structures for the storage of
liquid: (Part 9): 1973 Structural aspects

(Part 1): 1965 General requirements (Part 10) :1973 Tests and testing apparatus

(Part 2): 1965 Reinforced concrete structures (Part 11) :1973 Prestressed concrete

2210:1998 Criteria for design of reinforced (Part 12) :1973 Miscellaneous


concrete shell structures and (3) 269:1989 Specification for ordinary
folded plates (jirst revision) Portland cement, 33 grade
3201:1988 Criteria for design and (@rth revision)
construction of precast-trusses 8112:1989 Specification for 43 grade
and purlins @st revision) ordinary Portland cement (fist
4090:1967 Criteria for design of reinforced revision)
concrete arches 12269:1987 Specification for 53 grade
4995 Criteria for design of reinforced ordinary Portland cement
concrete bins for Storage 8041:1990 Specification for rapid
of granular and powdery hardening Portland cement
materials (second revision)
(Part 1): 1974 General requirements and bin 455:1989 Specillcation for Portland slag
loads cement @urth revision)
(Part 2): 1974 Design criteria 1489 Specification for Portland
4998 Criteria for design of reinforced pozzolana cementi
(Part 1): 1992 concrete chimneys: Part 1 (Part 1): 1991 Fly ash based (third revision)
Assessment of loads (second (Part 2): 1991 Calcined clay based (third
revision) revision)
(2 4845: 968 Definitions and terminology
8043:1991 Specification for hydrophobic
relating to hydraulic cement
Portland cement (second
6461 Glossary of terms relating to revision)
cement:
12600:1989 Specification for low heat
(Part 1): 1972 Concrete aggregates Portland cement
(Part 2): 1972 Materials 12330:1988 Specification for sulphate
(Part 3): 1972 Concrete reinforcement resisting Portland cement

NATIONAL BUILDING CODE OF INDIA


IS No. Title 1S No. Title
(4) 6452:1989 Specification for high alumina 1566:1982 Specification for hard-drawn
cement for structural use steel wire fabric for concrete
6909:1990 SPeeiticationfor supersulphated reinforcement (second
cement revision)

(5) 3812 Specification for pulverized 2062:1999 Steel for general structural
fuel ash: purposes (flfih revision)
(Part 1): 2003 For use as pozzolana in cement, (13) 4082:1996 Recommendations on stacking
cement mortar and concrete and storage of construction
(second revision) materials and components at
site (second revision)
(Part 2): 2003 For use as admixture in cement
mortar and concrete (second (14) 516:1959 Method of test for strength of
revision) concrete
(6) 12089:1987 Specification for granulated 5816:1999 Method of test for splitting
slag for manufacture of Portland tensile strength of concrete
slag cement @rst revision)
(7) 383:1970 Specification for coarse and (15) 1343:1980 Code of practice forprestressed
fine aggregates from natural concrete @-st revision)
sources for concrete (second (16) 1199:1959 Methods of sampling and
revision) analysis of concrete
(8) 3025 Methods of sampling and test (17) 9013:1978 Method of making, curing
(physical and chemical) for and determining compressive
water and waste water: strength of accelerated cured
(Part 17) :1984 Non-filterable residue (total concrete test specimens
suspended solids) (first (18) 383:1970 Specification for coarse and
revision) fine aggregates from natural
(Part 18) :1984 Volatile and fixed residue sources for concrete (second
(total filterable and non- revision)
filterable) (jirst revision) 455:1989 Specification for Portland slag
(Part 22) :1986 Acidity (jirst revision) cement (jowth revision)
(Part 23) :1986 Alkalinity (jirst revision) (19) 1489 Specification for Portland
(Part 24) :1986 Sulphates @rst revision) (Part 1): 1991 pozzolana cement: Part 1 Fly
ash based (third revision)
(Part 32) :1988 Chloride (first revision)
(20) 6909:1990 Specification for super-
(9) 516:1959 Method of test for strength of
sulphated cement
concrete
(21) 4925:1968 Specification for concrete
(lo) 4031 Methods of physical tests
batching and mixing plant
(Part 5): 1988 for hydraulic cement: Part 5
Determination of initial and (22) 4926:2003 Code of practice for ready-
final setting times (/irs[ revision) mixed concrete (second
revision)
(11) 9103:1999 Specification for admixtures
for concrete (first revision) (23) 2386 Methods of test for aggregates
(Part 3): 1963 for concrete: Part 3 Specific
(12) 432 Specification for mild steel
gravity, density, voids,
(Part 1): 1982 and medium tensile steel bars
absorption and bulking
and hard-drawn steel wire for
(24) 1791:1985 Specification for batch type
concrete reinforcement: Part 1
concrete mixers (second
Mild steel and medium tensile
steel bars (third revision) revision)
12119:1987 General requirements for pan
1786:1985 Specification for high strength
mixers for concrete
deformed steel bars and wires
for concrete reinforcement (25) 14687:1999 Guidelines for falsework for
(third revision) concrete structure

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE: 5A PLAIN AND REINFORCED CONCRETE 89


IS No. Title 1sNo. Title
(26) 2502:1963 Code of practice for bending (34) 1893 Criteria for earthquake resistant
and fixing of bars for concrete (Part 1): 2002 design of structures: General
reinforcement provisions and buildings (flflh
(27) 2751:1979 Recommended practice for revision)
welding of mild steel plain and (35) 1904:1986 Code of practice for design and
deformed bars for reinforced construction of foundations in
construction (@st revision) soils: General requirements
9417:1989 Recommendations for welding (third revision)
cold worked bars for reinforced (36) 1641:1988 Code of practice for fire safety
concrete construction (first of buildings (general): General
revision) principles of fire grading and
(28) 2505:1992 Concrete vibrators — classification (/irst revision)
Immersion type — General (37) 1642:1989 Code of practice for fire
requirements safety of buildings (general):
2506:1985 General requirements for Details of construction @rst
screed board concrete vibrators revision)
@rst revision)
(38) 13920:1993 Code of practice for ductile
2514:1963 Specification for concrete detailing of reinforced concrete
vibrating tables structures subjected to seismic
4656:1968 Specitlcation for form vibrators forces
for concrete (39) 4326:1993 Code of practice for
(29) 118” 7:1986 Classification of joints in earthquake resistant design
buildings for accommodation of and construction of buildings
dimensional deviations during (second revision)
construction Specification for high strength
(40) 1786:1985
(30) 786’ Code of practice for extreme deformed steel bars and wires
weather concreting: for concrete reinforcement
(Part 1): 1975 Recommended practice for (third revision)
hot weather concreting (41) 3414:1968 Code of practice for design
(Part 2): 1981 Recommended practice for and installation of joints in
cold weather concreting buildings
(31) 9013:1978 Method of making, curing (42) 3951 Specification for hollow clay
and determining compressive (Part 1): 1975 tiles for floors and roofs: Part 1
strength of accelerated cured Filler type (jrst revision)
concrete test specimens (43) 6061 Code of practice for
(32) 13311 Methods of non-destructive construction of floor and roof
testing of concrete: with joists and filler blocks:
(Part 1): 1992 Ultrasonic pulse velocity (Part 1): 1971 With hollow concrete filler
(Part 2): 1992 Rebound hammer blocks

(33) 875 Code of practice for design (Part 2): 1981 With hollow clay filler blocks
loads (other than earthquake) (jWst revision)
for buildings and structures: (44) 432 Specification for mild steel
(Part 1): 1987 Dead loads — Unit weights of (Part 1): 1982 and medium tensile steel bars
building material and stored and hard-drawn steel wire for
materials (second revision) concrete reinforcement Part 1
Mild steel and medium tensile
(Part 2): 1987 Imposed loads (second revision)
steel bars (third revision)
(Part 3): 1987 Wind loads (second revision)
(45) 1566:1982 Specification for hard-
(Part 4): 1987 Snow loads (second revision) drawn steel wire fabric for
(Part 5): 1987 Special loads and load concrete reinforcement (second
combinations (second revision) revision)

90 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 5 Concrete: 5B Prestressed Concrete

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 STRUCTURAL DESIGN USING PRESTRESSED CONCRETE ... 5

NATIONAL BUILDING CODE OF INDIA


F“

National Building Code Sectional Committee, CED 46

FOREWORD

This sub-section covers the structural design aspects of prestressed concrete.

This sub-section is largely based on IS 1343:1980 ‘Code of practice for prestressed concrete @-st revision)’,
which is under revision at the time of publication of this Code. Major changes have been envisaged in the
revision of IS 1343. In the absence of availability of finalized version of revised IS 1343, at the time of revision
of this Code, the provision of design as per existing IS 1343: 1980 have been continued through appropriate
reference to the same.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCRETE 5B PRESTRESSED CONCRETE 3


. ---
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 5 Concrete: 5B Prestressed Concrete

1 SCOPE a) materials, workmanship, inspection and


testing;
This sub-section deals with the general structural use
of prestressed concrete. It covers both work carried b) general design requirements; and
out on site and the manufacture of precast prestressed c) structural design: limit state method,
concrete units.
shall be in accordance with good practices contained
2 STRUCTURAL DILSIGNUSINGPRES-ED in IS 1343: 1980 ‘Code of practice for prestressed
CONCRETE concrete (first revision)’.
NOTE- At the timeof publicationof this sub-section,IS 1343
The provisions relating to design and general structural
was under revision;and once the revisedIS 1343is pubtished,
use of prestressed concrete including on: the same shall replacethe provisionsgiven in this sub-section.

PART 6 STRUCTURAL DESIGN — SECTION 5 CONCREIR 5B PRESTRESSED CONCRETE


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 6 Steel

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 TERMINOLOGY .,. 5
3 PLANS AND DRAWINGS ... 5
4 MATERIALS ... 5
5 DESIGN AND CONSTRUCTION IN STEEL ... 5
6 DESIGN USING LIMIT STATE METHOD ... 5
7 SPACE FRAME ... 6

LIST OF STANDARDS ... 6

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Section covers the structural design aspect of steel structures in buildings.

This Section covers the use of hot-rolled structural steel sections and steel tubes in buildings. It permits the
design by working stress method and plastic theory, and now in this revision by limit state method. Further,
reference to space frame has now found place in this Section.

This Section is based on IS 800:1984 ‘Code of practice for general construction in steel (second revision)’ and
IS 806:1968 ‘Code of practice for use of steel tubes in general building construction @-st revision)’, and also
enables design using limit state method.

More rigorous analytical procedures than envisaged as per this Section are available and can be made use of for
finding effective lengths of compression members in determining elastic critical loads.

The Indian Standard IS 800, on which this Section is largely based is under revision at the time of publication of
this Code. Major changes have been envisaged in the revision of IS 800 including introduction of limit state
method. In the absence of availability y of finalized version of revised IS 800 at the time of revision of this Section,
in this revision, the provisions of design as per existing IS 800: 1984 have been continued through appropriate
reference to the same; similarly reference has been made to IS 806. At the same time, the limit state method
having already gained acceptance has been taken into account in this revision by providing suitable enabling
provisions and also covering certain general principles thereof.

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

PART 6 STRUCTURAL DESIGN — SECTION 6 STEEL


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 6 Steel

1 SCOPE conform to Part 5 ‘Building Materirds’. Structural steel,


rivets, welding consumables, steel castings, bolts and
1.1 This Section covers the use of structural steel in
nuts, washers and steel tubes shall be in accordance
general building construction including the use of hot
with accepted standards [6-6(3)] and other relevant
rolled steel sections and steel tubes.
Indian Standards.
1.2 The provisions of this Section are generally
applicable to rivetted, bolted and welded construction. 5 DESIGN AND CONSTRUCTION IN STEEL

The design and construction in steel including general


2 TERMINOLOGY
design requirements, design of tension members,
For the purpose of this Section, the definitions as given design of compression members, design of members
in accepted standard [6-6(1)] shall apply. subjected to bending, design of members subjected to
combined stresses, design of connections, plastic
3 PLANS AND DRAWINGS design, design of encased members, fabrication and
3.1 Plans, drawings and stress sheets shall be prepared erection, and the steel work tenders and contracts, shall
according to good practice [6-6(2)]. be done in accordance with good practice [6-6(1)] and
the design and construction involving use of steel tubes
3.2 Plans shall be in accordance with good practice [6-6(4)].
The plans (design drawings) shall show the complete
6 DESIGN USING LIMIT STATE METHOD
design with sizes, sections, and the relative locations
of the various members. Floor levels, column centres, 6.1 General
and offsets shall be dimensioned. Plans shall be drawn
6.1.1 The design in steel maybe done using the limit
to a scale large enough to convey the information
state method, which is generally based on the following
adequately. Plans shall indicate the type of construction
basic aspects/principles:
to be employed; and shall be supplemented by such
data on the assumed loads, shears, moments and axial a) It makes use of the plastic range of material
forces to be resisted by all members and their for the design of structural members and
connections, as may be required for the proper incorporates load factors to take into account
preparation of shop drawings. Any special precaution the variability of loading configurations.
to be taken in the erection of structure from the design b) It considers the good performance of steel in
considerations, the same shall also be indicated in the tension compared to compression and
drawing. specifies variable factors. It takes into account
this variance by defining limit states which
3.3 Shop Drawings
address strength and serviceability.
Shop drawings, giving complete information necessary c) According to this method, a structure or part
for the fabrication of the component parts of the of it, is considered unfit for use when it
structure including the location, type, size, length and exceeds the limit state beyond which it
detail of all welds, shall be prepared in advance of the infringes any one of the criteria governing its
actual fabrication. They shall clearly distinguish performance or use. .,
between shop and field rivets, bolts and welds. For d) The two limit states are classified as the
additional information to be included on drawings for Ultimate Limit State and Serviceability Limit
designs based on the use of welding, reference shall State. The limit states take care of the safe
be made to appropriate Indian Standards. Shop operation and adequacy of the structure from
drawings shall be made in accordance with good strength point of view. The criteria which are
practice [6-6(2)]. A marking diagram allotting distinct used to define the ultimate limit state are
identification marks to each separate part of steel work yielding, plastic strength, fatigue, buckling,
shall be prepared. The diagram shall be sufficient to etc. Serviceability limit state takes care of the
ensure convenient assembly and erection at site. performance and behaviour of the structure
during its service period. Deflection, vibration,
4 MATERIALS
drift, etc are considered as serviceability
All materials used in structural steel construction shall criteria.

PART 6 STRUCTURAL DESIGN — SECTION 6 STEEL 5


e) Limit state method considers the critical local where
buckling stress of the constituent plate
element of a member. This method has Y. = Yf l’ml .?’mz

provisions to enhance resistance of plate = Partial safety factor for material.


elements against local buckling by suitably ?’,
= Partial factor for loads.
reducing the slenderness ratio. Hence, it is Yf Factor that takes into account the
possibIe to develop the full flexural moment inaccuracies in assessment of loads,
capacity of a member subjected to flexure or stress distribution and construction
the Limit State in flexure for abeam. In Limit tolerances.
State Method, based on slenderness ratio of
y~l, y~ = Factors that take into account,
the constituent plate elements, a member can
uncertainties in material strength and
be classified as Slender, Semi-compact,
quality, and manufacturing tolerances
Compact and Plastic. This section classification
respectively.
becomes essential as the moment or load
capacities of each of these sections take Q, = Specified nominal load induced based
on design stipulations.
different values depending upon these
classifications. cry = Yield strength of the material.

6.1.2 In this method, the factored loads, in different 6.2 The detailed design procedure shall be as agreed
combinations, are applied to the structure to determine between the parties concerned.
the load effects. The latter are then compared with the
NOTE— At the time of publication of this Section IS 800
design strength of the elements. was under revision and once the revised IS 800 is published,
the same shall replace the provisionsgiven in this section.
This is expressed mathematically as:

The effects of 7 SPACE FRAME

For analysis and design of space frame along with its


components, specialist literature may be referred to,
and the methodology for the same may be as agreed
[Function of o, and other geometric variables] between the parties concerned.

LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’ (Part 1): 1985 Tolerances of form, orientation,
in the fulfillment of the requirements of the Code. The location and run-out, and
latest version of a standard shall be adopted at the time appropriate geometrical
of enforcement of the Code. The standards listed may definitions (lirst revision)
be used by the Authority as a guide in conformance (Part 2): 1992 Maximum material principles
with the requirements of the referred clauses in the (first revision)
Code.
(Part 3): 1992 Dimensioning and tolerancing
In the following list, the number appearing in the first of profiles (second revision)
column within parentheses indicates the number of the (Part 4): 1976 Practical examples of indications
reference in this PartJSection. on drawings
1S No. Title IS 8976:1978 Guide for preparation and
(1) 800:1984 Code of practice for general arrangement of sets of drawings
construction in steel (second and parts list
revision) (3) Structural Steel
(2) 962:1989 Code of practice for architectural 1977:1996 Specification for low tensile
and building drawings (second structural steels (third revision)
revision) 2062:1999 Specification for steel for
8000 Geometrical tolerancing on g&eral structural purpose (jijlh
technical drawings: revision)

6 NATIONAL BUILDING CODE OF INDIA


IS No. Title 1S No. Title
8500:1991 Specification for structural Steel Castings
steel-microalloyed (medium 1030:1998 Specification for carbon steel
and high tensile qualities) (fht castings for general engineering
revision) purposes (fifth revision)
1161: 998 Specification for steel tubes 2708:1993 Specification for 1.5 percent
forstructural purposes (third
manganese steel castings for
revision)
general engineering purposes
Rivets (third revision)
1929: 982 Specification for hot forged Bolts and ,Nuts
steel rivets for hot closing
1363 Specification for hexagon head
(12 to 36 mm diameter) (@w
bolts, screws and nuts of
revision)
product grade C:
2155:1982 Specification for cold forged
(Part 1): 2002 Hexagon head bolts (size range
solid steel rivets for hot closing
M5 to M64) ~ourth revision)
(6 to 16 mm diameter) (first
revision) (Part 2): 2002 Hexagon head screws (size
1148:1982 Specification for hot-rolled rivet range M5 to M64) (fourth
bars (up to 40 mm diameter) revision)
for structural purposes (third (Part 3): 2002 Hexagon nuts (size range M5 to
revision) M64) ~ourth revision)
1149:1982 Specification for high tensile IS 1364 Specification for hexagon head
steel rivet bars for structural bolts, screws and nuts of
purposes (third revision) product grade A and B:

Welding Consumables (Part 1): 1992 Hexagon head bolts (size range
Ml.6 to M64) ~ourth revision)
1278:1972 Specification for filler rods and
wires for gas welding (second (Part 2): 2002 Hexagon head screws (size
revision) range Ml.6 to M64) (fourth
revision)
814:1991 Specification for covered
electrodes for manual metal arc IS 1367 Technical supply conditions for
welding of carbon and carbon threaded steel fasteners:
manganese steels f$ijlh revision) (Part 1): 2002 General requirements for
1395:1982 Specification for low and bolts, screws and studs (third
medium alloy steel covered revision)
electrodes for manual metal arc (Part 2): 2002 Tolerances for fastners — Bolts,
welding (third revision) screws, studs and nuts —
7280:1974 Specification for bare wire Product grades A, B and C
electrodes for submerged arc (third revision)
weMing of structural steels IS 3640:1982 Specification for hexagon fit
3613:1974 Specification for acceptance bolts (jlrst revision)
tests for wire-flux combinations IS 3757:1985 Specification for high strength
for submerged arc welding first structural bolts (second
revision) revision)
6419:1996 Specification for welding rods IS 6623:1985 Specification for high strength
and bare electrodes for gas structural nuts (jirst revision)
shielded arc welding of
IS 6639:1972 Specification for hexagon bolts
structural steel (jirst revision)
for steel structures
6560:1996 Specification for molybdenum
Washers
and chromium-molybdenum
low alloy steel welding rods and IS 5369:1975 General requirements for plain
bare electrodes for gas shielded washers and lock washers oirst
arc welding @rst revision) revision)

PART 6 STRUCTURAL DESIGN — SECTION 6 STEEL 7


IS No. Title IS No. Title

5370:1969 Specification for plain washers 5624:1993 Specification for foundation


with outside diameter more than bolts @-st revision)
three times the diameter 6610:1972 Specification for heavy washers
for steel structures
5372:1975 Specification for taper washers
6649:1985 Specification for hardened and
for channels (ISMC) (first
tempered washers for high
revision)
strength structural bolts and nuts
5374:1975 Specification for taper washers first revision)
for I-beams (ISMB) (first (4) 806:1968 Code of use of steel tubes in
revision) general building construction

NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 7 Prefabrication, Systems Building and


Mixed/Composite Construction: 7A Prefabricated Concrete

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 MATERIALS, PLANS AND SPECIFICATIONS ... 6
4 MODULAR CO-ORDINATION, ARCHITECTURAL TREATMENT . .. 6
AND FINISHES
5 COMPONENTS . .. 7
6 PREFABRICATION SYSTEMS AND STRUCTURAL SCHEMES ... 8
7 JOINTS ... 12
8 TESTS FOR COMPONENTS/STRUCTURES ... 13
9 MANUFACTURE, STORAGE, TRANSPORT AND ERECTION OF ... 14
PRECAST ELEMENTS
10 EQUIPMENT ... 20
11 PREFABRICATED STRUCTURAL UNITS ... 21

LIST OF STANDARDS ... 21

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

Prefabrication, though desirable for large scale building activities, has yet to take a firm hold in the country. Two
aspects of prefabrication specifically to be borne in mind are the system to be adopted for the different categories
of buildings and the sizes of their components. Here the principle of modular co-ordination is of value and its use
is recommended.

Advantages of recent trends in prefabrication have been taken note of and also the hazards attended to such
construction. A few recommendations on the need to avoid ‘progressive collapse’ of the structure have been
included. This has become necessary in view of such collapses in the past. A specific point to be borne in mind,
therefore, is the need to make the structure reasonably safe against such a collapse.

Prefabricated constructions being comparatively a new technique, some of the essential requirements for the
manufacture of the prefabricated components and elements are also included in this Section.

Since the aim of prefabrication is to effect economy, improvement in quality and speed in construction, the
.-
selection of proper materials for prefabrication is also an important factor in the popularization of this technique.
The use of locally available materials with required characteristics and those materials which, due to their innate
characteristics like lightweight, easy workability, thermal insulation, non-combustibility, etc, effect economy
and improved quality, may be tried. However, this Section pertains to prefabricated elements with cementations
materials.

It is possible to achieve or evolve aesthetically satisfying designs using prefabricated construction. A careful and
judicious handling of materials and use of finishes on a prefabricated building can help the designer a great deal
in ensuring that the appearance of the building as aesthetically appealing. The purpose of finishes and architectural
treatment is not only to give prefabricated buildings an individual character but also to effect better performance
and greater user satisfaction.

The design of prefabricated buildings shall include provision for all installations of services and their required
piping, wiring and accessories to be installed in the building.

This Section was first published in 1970 and was subsequently revised in 1983. In the last revision the following
main changes were made:

a) A brief provision regarding importance of architectural treatment and finishes as applicable to


prefabricated buildings were included;
b) A brief clause was added on the requirements of materials for use in prefabrication;
c) The clause on prefabricating systems and structural elements was elaborated;
d) The clause on testing of components was revised to include testing of structure or part of structure; and
e) A brief clause on the manufacture of cellular concrete was added.

In this revision, this Section, earlier named as Prefabrication and Systems Building has been named and restructured
as follows:

Section 7 Prefabrication, Systems Building and Mixed/Composite Construction


7A Prefabricated Concrete
7B Systems Building and Mixed/Composite Construction

This sub-section covers Prefabricated concrete. In this revision the following main changes have been made:

a) Modular coordination and modular dimension of the components have been revised to have more
flexibility for planning.
b) The provisions on tolerance has been revised to include different types of prefabricated components.

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 3


c) A detailed clause on design requirements for safety of prefabricated buildings against progressive clause
has been included.
d) A clause on sampling procedure has been added for testing of components.
e) List of Indian Standards referred as good practice has been updated, specially in view of formulation of
a large number of new Indian Standards on partially prefabricated components.

All standards cross-refereed to in the main text of the sub-section, are subject to revision. The parties to agreement
based on this sub-section are encouraged to investigate the possibility of applying the most recent editions of the
standard.

4 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 7 Prefabrication, Systems Building and


Mixed/Composite Construction: 7A Prefabricated Concrete

1 SCOPE co-ordination employing the basic module or a mtrlti-


module.
This sub-section gives recommendations regarding
modular planning, component sizes, prefabrication NOTE — The purposes of modular co-ordhation are:

systems, design considerations, joints and manufacture, a) to reduce the variety of component sizes produced, and

storage, transport and erection of prefabricated h) to allow the building designer greater flexibility in the
arrangement of components.
concrete elements for use in buildings and such related
requirements for prefabricated concrete. 2.1.10 Modular Grid — A rectangular coordinate
reference system in which the distance between
2 TERMINOLOGY consecutive lines is the basic module or a multi-
2.1 For the purpose of this sub-section, the following modtde. This multi-module may differ for each of the
definitions shall apply. two dimensions of the grid.

2.1.1 Authority Having Jurisdiction – The Authority 2.1.11 Multi-module — A module whose size is a
which has been created by a statute and which, for the selected multiple of the basic module.
purpose of administering the Code/Part, may authorize 2.1.12 Prefabricate — To fabricate components or
a committee or an official or an agency to act on its assembled units prior to erection or installation in a
behalfi hereinafter called the ‘Authority’. building.
2.1.2 Basic Module — The fundamental module used 2.1.13 Prefabricated Building — The partlylfully
in modular co-ordination, the size of which is selected assembled and erected building, of which the structural
for general application to building and its components. parts consist of prefabricated individual units or
NOTE — The value of the basic module has been chosen as assemblies using ordinary or controlled materials,
100 mm for the maximum flexibility and convenience. The including service facilities; and in which the service
symbol for the basic module is M.
equipment may be either prefabricated or constructed
2.1.3 Cellular Concrete — The material consisting of in-situ.
an inorganic binder (such as, lime or cement or both)
2.1.14 Sandwich Concrete Panels — Panels made by
in combination with a finely ground material
sandwiching an insulation material between two layers
containing siliceous material (such as sand), gas
of reinforced concrete to act as insulation for concrete
generating material (for example, aluminium powder),
panels.
water and harmless additives (optional); and steam
cured under high pressure in autoclaves. 2.1.15 Self Compacting Concrete — Concrete that is
able to flow under its own weight and completely fill
2.1.4 Components — A building product formed as a
the voids within the formwork, even in the presence
distinct unit having specified sizes in three dimensions.
of dense reinforcement without any vibration, whilst
2.1.5 Composite Members — Structural members maintaining homogeneity without segregation.
comprising prefabricated structural units of steel,
2.1.16 Shear Connectors — Stmctural elements, such
prestressed concrete or reinforced concrete and cast
as anchors, studs, channels and spirals, intended to
imsitu concrete connected together in such a manner
transmit the horizontrd Wear between the prefabricated
that they act monolithically.
member and the cast in-situ concrete and also to
2.1.6 Increments — Difference between two prevent vertical separation at the interface.
homologous dimensions of components of successive
sizes. 2.1.17 System — It is a particular method of
construction of buildings with certain order and
2.1.7 Light Weight Concrete — Concrete of discipline using the prefabricated components, tunnel
substantially lower unit weight than that made from form or large panel shutters which are inter-related in
gravel or crushed stone. functions and are produced based on a set of
2.1.8 Module — A unit of size used in dimensional instructions.
co-ordination. 2.1.18 Unit — Building material formed as a simple
2.1.9 Modular Co-ordination — Dimensional article with all three dimensions specified, complete

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 5


in itself but intended to be part of a compound unit or further work is necessary to outline suitable range of
complete building. Examples are brick, block, tile, etc. multi-modules with greater increments, often referred
to as preferred increments. A set of rules as detailed
3 MATERIALS, PLANS AND SPECIFICATIONS below would be adequate for meeting the requirements
3.1 Materials of conventional and prefabricated construction.

All materials shall conform to Part 5 ‘Building Materials’. These rules relate to the following basic elements:

3.1.1 While selecting the materials for prefabrication, a) The planning grid in both directions of the
the following characteristics shall be considered: horizontal plan shall be:
1) 15 M for industrial buildings,
a) Easy availability;
2) 3 M for other buildings.
b) Light weight for easy handling and transport;
The centre lines of load bearing walls should
c) Thermal insulation property;
preferably coincide with the gridlines.
d) Easy workability;
b) The planning module in the verticrd direction
e) Durability; shall be 2 M for industrial buildings and 1 M
f) Non-combustibility; for other buildings.
.!3) Sound insulation; c) Prefened increments for sill heights, doors,
h) Economy; and windows and other fenestration shall be 1 M.
j) Any other special requirement in a particular d) In the case of internal columns, the grid lines
application. shall coincide with the centre lines of
..-
columns. In case of external columns and
3.2 Plans and Specifications columns near the lift and stair wells, the grid
The detailed plans and specifications shall cover the lines shall coincide with centre lines of the
following: column in the topmost storey.

a) Such drawings shall describe the elements and 4.2 Architectural Treatment and Finishes
the structure and assembly including all
Treatment and finishes have to be specified keeping
required data of physical properties of
in view the requirements of protection, function and
component materials. Material specification,
aesthetics of internal and external spaces and surfaces.
age of concrete for demoulding, casting/erection
tolerance and type of curing to be followed. While deciding the type of architectural treatment and
b) Details of connecting joints of prefabricates finishes for prefabricated buildings, the following
shall be given to an enlarged scale. points should be kept in view:
c) Site or shop location of services, such as a) Suitability for mass production techniques;
installation of piping, wiring or other b) Recognition of the constraints imposed by the
accessories integral with the total scheme shall level of workmanship available;
be shown separately.
c) Possibility of using different types of finishes;
d) Data sheet indicating the location of the inserts
d) Use of finishes and architectural treatment
and acceptable tolerances for supporting the
for the creation of a particular architectural
prefabricate during erection, location and
character in individual buildings and in
position of doors/windows/ventilators, etc, if
groups of buildings by the use of colour,
any.
texture, projectio~ and recesses on surfaces,
e) The drawings shall also clearly indicate etc; ,“
location of handling arrangements for lifting
e) Incorporation of structural elements like
and handling the prefabricated elements.
joists, columns, beams, etc, as architectural
Sequence of erection with critical checkpoints
features and the treatment of these for better
and measures to avoid stability failure during
overall performance and appearance;
construction stage of the building.
f) Satisfactory finishing of surfaces; and
4 MODULAR CO-ORDINATION, g) Use of light weight materials to effect
ARCHITECTURAL TREATMENT AND economy in the structural system.
FINISHES
Some of the acceptable methods of finishes integral
4.1 Modular Co-ordination with the precasting are:

The basic module is to be adopted. After adopting this, a) Concrete surface moulded to design; shape;

6 NATIONALBUILDING CODE OF INDIA


b) Laid-on finishing tiles fixed during casting; 5.2 Casting Tolerances of Precast Components
c) Finishes obtained by washing, tooling,
grinding, grooving of hardened concrete; S1 Product Tolerances Product
No. (see
d) Exposed aggregates; and
Note)
e) Other integral finishes. (2) (3)
(1)
5 COMPONENTS i) Length
5.1 The preferred dimensions of precast elements shall *5mm 1,7
be as follows: &5 mm or & 0.1 percent whichever is 2, 3, 8
greater
a) Flooring and Roofing Scheme — Precast + 0.1 percent subject to maximum 4
slabs or other precast structural flooring
units:
1) Length — Nominal length shall be in & 2 mm for length below and up to 5
multiples of 1 M; 500 mm
* 5 mm for length over 500 mm 5
2) Width — Nominal width shall be in
multiples of 0.5 M, and *lomm 6,9,10

3) Overall Thickness — Overall thickness ii) Thickness/Cross-sectional dimensions


shall be in multiples of 0.1 M. *3mm 1
b) Beams k 3 mm or 0.1 percent whichever is 2,8
greater
1) Length — Nominal length shall be in
* 2 mm up to 300 mm wide
multiples of 1 M, 4
f 3 mm greater than 300 mm wide
2) Width — Nominal width shall be in *2mm 3,7
multiples of 0.1 M, and *4mm 6,9, 10
3) Overall Depth — Overall depth of iii) StraightnessA90w
the floor zone shall be in multiples of 2,4,8
& 5 mm or 1/750 of length whichever
0.1 M. is greater
c) Columns &3mm 1,5
1) Height — Height of columns for *2mm 7
industrial and other building 1 M, and iv) Squareness
2) Lateral Dimensions — Overall lateral When considering the squareness of
dimension or diameter of columns shall the corner, the longer of two adjacent
be in multiples of 0.1 M. sides being checked shall be taken as
the base line.
d) Walls
The shorter side shall not vary in 2,5,8
Thickness — The nominal thickness of walls length from the perpendicular by
shall be in multiples of 0.1 M. more than 5 mm
e) Staircase The shorter side shall not vary in 1,7
length from the perpendicular by
Width — Nominal width shall be in multiples
more than 3 mm
of 1 M.
The shorter side shall not be out of 4
f) Lintels
square line for more than ~~ mm
1) Length — Nominal length shall be in
multiples of 1 M, v) Twist
2) Width — Nominal width shall be in Any corner shall not be more than
multiples of 0.1 iW and the tolerance given below from the
3) Depth — Nominal depth shall be in plane containing the other three
multiples of 0.1 M. comers:
* 5 mm (Up to 600 mm in width and 2,8
g) SunshadeslChajja Projections
up to 6 m in length)
1) Length — Nominal length shall be in & 10 mm (Over 600 mm in width and
multiples of 1 M. for any length)
2) Projection — Nominal length shall be in * 1/1 500 of dimension of & 5 mm 4
multiples of 0.5 M. whichever is less

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 7


6.3 Prefabrication Systems
(1) (2) (3)
The system of prefabricated construction depends on
*3mm 1
~lmm 7 the extent of the use of prefabricated components, their
materials, sizes and the technique adopted for their
vi) Flatness
manufacture and use in building.
The maximum deviation from 1.5 m
straight edge placed in any position 6.3.1 Types of Prefabrication Components
on a nominal plane surfiace shall not The prefabricated concrete components such as those
exceed given below may be used which shall be in accordance
k5mm 2, 8
with Part 5 ‘Building Materials’ and the accepted
Y3mm 4
stmdards [6-7A(l)], where available:
*2mm 1.7
z 4 or maximum of 0,1 percent 5 a) Reinforced/Prestressed concrete channel unit,
length b) Reinforced/Prestressed concrete slab unit,
NOTES — Key for product reference c) Reinforced/Prestressed concrete beams,
1 Channel unit d) Reinforced/Prestressed concrete columns,
2 Ribbed slab unitihollow slab
e) Reinforced/Prestressed concrete hollow core
3 Waffle unit
slab,
4 Large panel prefabrication
5 Cellular concrete floor/roof slabs o Reinforced concrete waffle slab/shells,
6 Prefabricated brick panel Reinforced/Prestressed concrete wall
g)
7 Precast planks
elements,
8 Ribbed/plain wall panel
9 Column h) Hollow/Solid blocks and battens,
10 Step unit j) Precast planks and joists for flooring and
roofing,
6 PREFABRICATION SYSTEMS AND k) Precast joists and trussed girders,
STRUCTURAL SCHEMES m) Light weighticellular concrete slabs,
6.1 The word ‘system’ is referred to a particular n) Precast lintel and chajjas,
method of construction of buildings using the P) Large panel prefabricates,
prefabricated components which are inter-related in Reinforced/Prestressed concrete trusses,
@
functions and are produced to a set of instructions. With
r) Reinforced/Prestressed roof purlins,
certain constraints, several plans are possible, using
s) Precast concrete L-panel unit,
the same set of components. The degree of flexibility
varies from system to system. However, in all the t) Prefabricated brick panel unit,
systems there is a certain order and discipline. u) Prefabricated sandwich concrete panel, and
v) Precast foundation.
6.2 The following aspects, among others, are to be
considered in devising a system: There may be other types of components which may
be used with the approval of the Authority.
a) Effective utilization of spaces;
NOTE — The elements may be cast at the site or off the site.
b) Straight and simple walling scheme;
c) Limited sizes and numbers of components; 6.3.2 There are two categories of open prefab system
Limited opening in bearing walls; depending on the extent of prefabrication used in the
d)
construction as given in 6.3P2.1 and 6.3.2.2.
e) Regulated locations of partitions;
Standardized service and stair units; 6.3.2.1 Partial prefabrication system
f)
g) Limited sizes of doors and windows with This system basically uses precast rooting and flooring
regulated positions; components and other minor elements like lintels,
h) Structural clarity and efficiency; CHA.1.lAS, kitchen sills in conventional building
construction. The structural system could be in the form
j) Suitability for adoption in low rise and high
of in-situ framework or load bearing walls.
rise building;
k) Ease of manufacturing, storing and 6.3.2.2 Full prefabrication system
transporting;
In this system almost all the structural components are
m) Speed and ease of erectiow and prefabricated. The filler walls may be of bricldblock
n) Simple jointing system. masonry or of any other locally available material.

8 NATIONAL BUILDING CODE OF INDIA


6.3.3 Large Panel Prefabrication System elements which come under this category are
channel slabs, hollow core slabs, channels and
This system is based on the use of large prefab
ties system, light weighticellular concrete
components. The components used are precast concrete
slabs, etc.
large panels for walls, floors, roofs, balconies,
staircases, etc. The casting of the components could b) Two way systems transfer loads in both the
be at the site or off the site. directions imparting loads on the four edges.
The precast elements under this category are
Depending upon the extent of prefabrication, this room sized panels, two way ribbed or waffle
system can also lend itself to partial prefab system and slab systems, etc.
full prefab system.
6.3.3.3 Staircase systems
Structural scheme with precast large panel walls can
be classified as given in 6.3.3.1 to 6.3.3.3. Staircase system may consist of single flights with in-
built risers and treads in the element. The flights are
6.3.3.1 Precast Walls normally unidirectional transferring the loads to
6.3.3.1.1 Based on the structural functions of the walls, supporting landing slabs or load bearing walls.
the precast walls may be classified as: 6.3.4 Box Type Construction
a) load bearing walls, In this system, room size units are prefabricated and
b) non-load bearing walls, and erected at site. Toilet and kitchen blocks could also be
c) shear walls. similarly prefabricated and erected at site.

6.3.3.1.2 Based on construction, the precast walls may NOTE — This system derives its stability and stiffness from
the box units which are formed by four adjacent walls. Walls
be classified as: are jointed to make rigid connections among themselves. The
box unit rests on foundation which may be of conventional
a) Homogeneous walls — which could be solid,
type or precast type.
hollow or ribbed; and
b) Non-homogeneous walls — these could be 6.4 Design Considerations
composite or sandwich panels. The precast structure should be analyzed as a
6.3.3.1.3 Based on their locations and functional monolithic one and the joints in them designed to take
requirements the precast walls may also classified as: the forces of an equivalent discrete system. Resistance
to horizontal loading shall be provided by having
a) external walls, which may be load bearing or appropriate moment and shear resisting joints or
non-load bearing depending upon the lay-out; placing shear walls (in diaphragm braced frame type
these are usually non-homogeneous walls of of construction) in two directions at right angles or
sandwiched type to impart better thermal otherwise. No account is to be taken of rotational
comforts; and stiffness, if any, of the floor-wall joint in case of precast
b) internal walls providing resistance against bearing wall buildings. The individual components
vertical loads, horizontal loads, fire, etc; these shall be designed, taking into consideration the
are normally homogeneous walls. appropriate end conditions and loads at various stages
of construction. The components of the structure shall
6.3.3.2 Precustfloors
be designed for loads in accordance with Part 6
6.3.3.2.1 Depending upon the composition of units, ‘Structural Design, Section 1 Loads, Forces and
precast flooring units may be homogeneous or non- Effects’. In addition members shall be designed for
homogeneous. handling, erection and impact loads that might be
expected during handling ahd erection.
a) Homogeneous floors may be solid slabs,
cored slabs, ribbed or waffle slabs. 6.4.1 In some conventional forms of construction,
b) Non-homogeneous floors may be multi- experience has shown that the structures are capable
layered ones with combinations of light of safely sustaining abnormal conditions of loading
weight concrete or reinforced/prestres sed and remaining stable after the removal of primary
concrete, with filler blocks. structural members. It has been shown that some
forms of building structure and particularly some
6.3.3.2.2 Depending upon the way the loads are industrialized large panel systems have little reserve
transferred, the precast floors may be classified as one
strength to resist forces not specifically catered
way or two way systems: for in the design. In the light of this, therefore,
a) One way system transfers loads to supporting recommendations made in 6.4.2 to 6.4.9 should be kept
members in one direction only. The precast in mind for ensuring stability of such structure.

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 9


I

t
6.4.2 Adequate buttressing of external wall panels is which one element falls during erection and lands on
important since these elements are not fully restrained an element below. The connections of the lower
on both sides by floor panels. Adequate design element then give way under the loading, both static
precautions may be taken by the designer. Experience and dynamic, and a chain reaction of further collapse
shows that the external wall panel connections are the is set up.
:
weakest points of a precast panel building.
6.4.9.1 A precaution against the first form of failure
6.4.3 It is equally important to provide restraint to all is that the overall stability of a building shall be
load bearing elements at the comers of the building. considered in all its erection stages as well as in its
These elements and the external ends of cross-wall completed state. All joints that may be required to resist
units should be stiffened either by introducing columns moments and shears during the erection stage only,
as connecting units or by jointing them to non- shall be designed with these in mind. Temporary works
structural wall units which in emergency may support required to provide stability during construction shall
the load. Jointing of these units should be done bearing be designed carefully.
in mind the need for load support in an emergency.
6.4.9.2 To guard against the second form of failure,
6.4.4 In prefabricated construction, the possibility of that is, the dropping of a unit during erection, particular
gas or other explosions which can remove primary attention shall be given to the details of all pre-formed
structural elements leading to progressive collapse of units and their seatings to ensure that they are
the structure shall be taken into account. It is, therefore, sufficiently robust to withstand the maximum stresses
necessary to consider the possibility of progressive that can arise from site conditions. Precast concrete
collapse in which the failure or displacement of one construction generally shall be capable of withstanding i-
element of a structure causes the failure or displacement the impact forces that can arise from bad workmanship
of another element and results in the partial or total on site.
collapse of the building.
6.5 Design Requirements for Safety Against
6.4.5 Provision in the design to reduce the probability
Progressive Collapse
of progressive collapse is essential in buildings of over
six storeys and is of relatively higher priority than for 6.5.1 Prefabricated buildings shall be designed with
buildings of lower height. proper structural integrity to avoid situations where
damage to small areas of a structure or failure of single
6.4.6 It is necessary to ensure that any local damage
elements may lead to collapse of major parts of the
to a structure does not spread to other parts of the
structure.
structure remote from the point of mishap and that the
overall stability is not impaired, but it may not be The following precaution may generally provide
necessary to stiffen all parts of the structure against adequate structural integrity:
local damage or collapse in the immediate vicinity of
a) All buildings should be capable of safely
a mishap, unless the design briefs specifically requires
resisting the minimum horizontal load of 1.5
this to be done.
percent of characteristic dead load applied at
6.4.7 Additional protection may be required in respect each floor or roof level simultaneously (see .
of damage from vehicles; further, it is necessary to Fig. 1).
consider the effect of damage to or displacement of a
load-bearing member by an uncontrolled vehicle. It is c 0.015 g ~,
strongly recommended that important structural DESIGN
WIND I c p.o15g ~~
members are adequately protected by concrete kerbs SEISMIC
c
r
or similar method. LOAD

6.4.8 In all aspects of erection that affect structural


design, it is essential that the designer should maintain
%
a close liaison with the builder/contractor regarding
the erection procedures to be followed. ...

6.4.9 Failures that have occurred during construction b) All buildings are provided with effective
appear to be of two types. The first of these is the pack- horizontal ties
of-cards type of collapse in which the absence of
1) Around the periphery
restraining elements, such as partitions, cladding or
shear walls, means that the structure is not stable during 2) Internally (in both directions)
the construction period. The second is the situation in 3) To columns and walls

10 NATIONALBUILDING CODE OF INDIA


c) Vertical ties for buildings of five or more The bars providing these ties may be distributed evenly
storeys. in the slabs (see Fig. 4) or may be grouped at or in the
In proportioning the ties, it may be assumed that no beams, walls or other appropriate positions but at
other forces are acting and the reinforcement is acting spacings generally not greater than 1.51,.
at its characteristic strength. 6.5.3.3 Horizontal ties to column and wall
Normal procedure may be to design the structure for
All external load-bearing members such as columns
the usual loads and then carry out a check for the tie
and walls should be anchored or tied horizontally into
forces.
the structure at each floor and roof level. The design
6.5.2 Continuity and Anchorage of Ties force for the tie is to be greater of

Bars shall be lapped, welded or mechanically joined a) 2 F, ~ or 1,x F,12.5 kN whichever is less for
as in accordance with Part 6 ‘Structural Design, Section a column or for each metre length if there is a
5 Plain, Reinforced and Prestressed Concrete: 5A Plain wall 1,is the floor to ceiling height in metres.
and Reinforced Concrete’. b) 3 percent of the total ultimate vertical load in
the column or wall at that level.
6.5.3 Design of Ties
For corner columns, this tie force should be provided
6.5.3.1 Peripheral ties
in each of two directions approximately at right angles.
At each floor and roof level an effectively continuous
tie should be provided within 1.2 m of the edge of the 6.5.3.4 Vertical ties (for buildings of five or more
storeys) ..—
building or within the perimeter wall (see Fig. 2).

The tie should be capable to resisting a tensile force of Each column and each wall carrying vertical load
F, equal to 60 kN or (20 + 4N) kN whichever is less, should be tied continuously from the foundation to the
where N is the number of storeys (including basement) roof level. The reinforcement provided is required only
to resist a tensile force equal to the maximum design
t. +-
ultimate load (dead and imposed) received from any

r- - l,2m CLADDING one storey.

In situation where provision of vertical ties cannot be


done, the element should be considered to be removed
and the surrounding members designed to bridge the
nil gap.

-L1
NOTE — If there are cantilever slabs, supporting external
6.5.4 Key Elements

For buildings of five or more storeys, the layout should


cladding, projecting in front of the columns and these are more be checked to identify key elements. A key element is
than 1.2 m, than the peripheral tie shall go in the slab. such that its failure would cause the collapse of more
FIG. 2 POSITION FOR PERIPHERAL TIE than a limited area close to it.

6.5.3.2 Internal ties The limited area defined above may be taken equal to
70 m2 or 15 percent of the area of the storey whichever
These are to be provided at each floor and roof level is lesser.
in two directions approximately at right angles. Ties
should be effectively continuous throughout their If key elements exists, it is preferable to modify the
length and be anchored to the peripheral tie at both layout so that the key element is avoided.
ends, unless continuing as horizontal ties to columns
6.6 Bearing for Precast Units
or walls (see Fig. 3). The tensile strength, in kN/m
width shall be the greater of Precast units shall have a bearing at least of 100 mm
on masonry supports and of 75 mm at least on steel or
(gk+q,)lr~ ~nd15F
concrete. Steel angle shelf bearings shall have a
7.5 5 “ ‘
100 mm horizontal leg to allow for a 50 mm bearing
where (g~ + q~) is the sum of average characteristic exclusive of fixing clearance. When deciding to what
dead and imposed floor loads in kN/m2 and 1, is the extent, if any, the bearing width may be reduced in
greater of the distance between the centre of columns, special circumstances, factors, such as, loading, span,
frames or walls supporting any two adjacent floor spans height of wall and provision of continuity, shall be
in the direction of the tie under consideration. taken into consideration.

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 11


ADDITIONAL BAR
FOR PERIPHERAL TIE

● 0

@o ● 0
)
TIE BARS

NOTE — If the peripheral tie consists of bars in an edge beam, then the bottom bars in the slabs will not be
at the same level as the peripheral tie bars. It is suggested that either an additional bar be used for the
peripheral tie or the internal tie bars be extended and anchored around the top bar in the beam.

FIG. 3 ANCHORING OF TIES IN SLABS


.

\ J
4

NOTE — For continuity in continuous slabs, bars are distributed evenly in a floor slab by means of lapping
some bottom steel at supports, either by extending existing bars or by the addition of splice bars.

FIG. 4 CONTINUITY REQUIREMENT FOR SLAB

7 ,JOINTS a) It shall be capable of being designed to


transfer the imposed load and moments with
7.1 The design of joints shall be made in the light of
a known margin of safety; ?%
their assessment with respect to the following
considerations: b) It shall occur at logical locations in the
structure and at points which may be most
a) Feasibility — The feasibility of a joint shall readily analysed and easily reinforced;
be determined by its load-carrying capacity
c) It shall accept the loads without marked
in the particular situation in which the joint is
displacement or rotation and avoid high local
to function.
stresses;
b) Practicability — Practicability of joint shall
d) It shall accommodate tolerances in elements;
be determined by the amount and type of
material required in construction; cost of e) It shall require little temporary support, permit
material, fabrication and erection and the time adjustment and demand only a few distinct
for fabrication and erection. operation to make;
c) Serviceability — Serviceability shall be f) It shall permit effective inspection and
determined by the joints/expected behaviour rectification;
to repeated or possible overloading and g) It shall be reliable in service with other parts
exposure to climatic or chemical conditions. of the building; and
d) Fire Rating — The fire rating for joints of h) It shall enable the structure to absorb
precast components shall be higher or at least sufficient energy during earthquakes so as to
equal to connecting members. avoid sudden failure of the structure.
e) Appearance — The appearance of precast +
7.2.1 Precast structures may have continuous or
components joint shall merge with hinged connections subject to providing sufficient
architectural aesthetic appearance and shall
rigidity to withstand horizontal loading. When only
not be physically prominent compared to
compressive forces are to be taken, hinged joints may
other parts of structural components.
be adopted. In case of prefabricated concrete elements,
7.2 The following are the requirements of a structural load is transmitted via the concrete. When both
joint: compressive force and bending moment are to be taken,

12 NATIONAL BUILDING CODE OF INDIA

..
rigid or welded joints may be adopted; the shearing to the dimensions requirements if no defective is found
force is usually small in the column and can be taken in the sample, and shall be rejected if the number of
up by the friction resistance of the joint. Here load defective is greater than or equal to the first rejection
transmission is accomplished by steel inserted parts number. If the number of defective is less than the
together with concrete. first rejection number the second sample of the same
size as taken in the first stage shall be selected from
7.2.2 When considering thermal shrinkage and heat
the lot at random and subjected to the dimensional
effects, provision of freedom of movement or
requirements. The number of defective in the first
introduction of restraint may be considered,
sample and the second sample shall be combined and
7.3 Joining techniques/materials normally employed if the combined number of defective is less than the
are: second rejection number, the lot shall be considered
as conforming to the dimensional requirements;
a) Welding of cleats or projecting steel,
otherwise not.
b) Overlapping reinforcement, loops and linking
steel grouted by concrete, The lot which has been found as satisfactory with
c) Reinforced concrete ties all round a slab, respect to the dimensional requirements shall then be
tested for load test. For this purpose one unit shall be
d) Prestressing,
selected for every 300 units or part thereof. The lot
e) Epoxy grouting, shall be considered as conforming to the strength
o Bolts and nuts connection, requirement if all the units meet the requirement;
g) A combination of the above, and otherwise not.
h) Any other method proven by test.
8.2 Testing on Individual Components
8 TESTS FOR COMPONENTS/STRUCTURES The component should be loaded for one hour at its
8.1 Sampling Procedure full span with a total load (including its own self
weight) of 1.25 times the sum of the dead and imposed
8.1.1 Lot loads used in design. At the end of this time it should
All the precast units of the same size, manufactured from not show any sign of weakness, faulty construction or
the same material under similar conditions of production excessive deflection. Its recovery one hour after the
shall be grouped together to constitute a lot. removal of the test load, should not be less than 75
percent of the maximum deflection recorded during
The number of units to be selected from each lot for the test. If prestressed, it should not show any visible
dimensional requirements shall depend upon the size cracks up to working load and should have a recovery
of the lot and shall be in accordance with CO11 and 2 of not less than 85 percent in 1 h.
of Table 1.
8.3 Load Testing of Structure or Part of Structure
Table 1 Sample Size and Rejection Number
Loading test on a completed structure should be made
(Clauses 8.1.1 and 8.1.2)
if required by the specification or if there is a
Lot Size First Seeond First Second reasonable doubt as to the adequacy of the strength
Sample Sample Rejection Rejection
Size Size Number Nmnber
of the structure.
(1) (2) (3) (4) (5) 8.3.1 In such tests the structure should be subjected
up to 100 5 5 2 2 to full dead load of the structures plus an imposed load
101 to300 8 8 2 2 equal to 1.25 times the specified imposed load used in
301to 500 13 13 2 2 design, for a period of 24 li and then the imposed load
500and above 20 20 3 4 shall be removed. During the tests, vertical struts equal
in strength to take the whole load should be placed in
The units shall be selected from the lot at random. In
position leaving a gap under the member.
order to ensure the randomness of selection, reference
may be made to good practice [6-7A(2)]. NOTE — Dead load includes self weight of the structural
members plus weight of finishes and walls or partitions, if any,
8.1.2 Number of Tests and Criteria for Conformity as considered in the design.

All the units selected at random in accordance with 8.3.1.1 If within 24 h of the removal of the load, a
CO1 1 and 2 of Table 1 shall be subjected to the reinforced concrete structure does not show a recovery
dimensional requirements. A unit failing to satisfy any o’fat least 75 percent of the maximum deflection shown
of the dimensional requirements shall be termed as during the 24 h under load, test loading should be
defective. The lot shall be considered as conforming repeated after a lapse of 72 h. If the recovery is less

PART 6 STRUCTURAL DESIGN— SECTION 7A PREFABRICATED CONCRETE 13


,y’

than 80 percent in second test, the structure shall be locally available labour force. The equipment
deemed to be unacceptable. machinery used may be minor in nature and moulds
are of mobile or stationary in nature.
8.3.1.2 If within 24 h of the removal of the load,
prestressed concrete structure does not show a recovery 9.1.2.2.2 Fully-mechanized
of at least 85 percent of the maximum deflection shown
The work will be carried out under shed with skilled
during the 24 h under load, the test loading should be
labour. The equipments used will be similar to one of
repeated. The structure should be considered to have
factory production. This type of precast yards will be
failed, if the recovery after the second test is not at
set up for the production of precast components of high
least 85 percent of the maximum deflection shown
quality, high rate of production.
during the second test.
Though there is definite economy with respect to cost
8.3.1.3 If the maximum deflection in mm, shown
of transportation, this system suffers from basic
during 24 h under load is less than 40 P-ID, where 1is
drawback of its non-suitability to any high degree of
the effective span in m; and D, the overall depth of the
mechanization and no elaborate arrangements for
section in mm, it is not necessary for the recovery to
quality control. Normal benefits of continuity of work
be measured and the recovery provisions of 8.3.1.1
is not available in this system of construction.
and 8.3.1.2 shall not apply.
9.1.3 The various processes involved in the
9 MANUFACTURE, STORAGE, TRANSPORT manufacture of precast elements may be classified as
AND ERECTION OF PRECAST ELEMENTS follows:
9.1 Manufacture of Precast Concrete Elements Main process
9.1.3.1
9.1.1 A judicious location of precasting yard with a) Providing and assembling the moulds, placing
concreting, initial curing (required for demoulding), reinforcement cage in position for reinforced
storage facilities, suitable transporting and erection concrete work, and stressing the wires in the
equipments and availability of raw materials are the case of prestressed elements;”
crucial factors which should be carefully planned and
b) Fixing of inserts and tubes, where necessary
provided for effective and economic use of precast
(for handling);
concrete components in constructions.
c) Pouring the concrete into the moulds;
9.1.2 Manufacture d) Vibrating the concrete and finishing;
The manufacture of the components can be done in a e) Curing (steam curing, if necessary); and
factory for the commercial production established at f) Demoulding the forms and stacking the
the focal point based on the market potential or in a precast products.
site precasting yard set up at or near the site of work.
9.1.3.2 Auxilia~ process
9.1.2.1 Factory prefabrication
Process necessary for the successful completion of the
Factory prefabrication is resorted to in a factory for processes covered by the main process:
the commercial production for the manufacture of
standardized components on a long-term basis. It is a a) Mixing and manufacture of fresh concrete
capital intensive production where work is done (done in a mixing station or by a batching
throughout the year preferably under a closed shed to plant);
avoid effects of seasonal variations. High level of b) Prefabrication of reinforcement cage (done in
mechanization can always be introduced in this system a steel yard or workshop);
where the work can be organized in a factory-like c) Manufacture of inserts and other finishing
manner with the help of a constant team of workmen. items to be incorporated in the main precast
products;
9.1.2.2 Site prefabrication
d) Finishing the precast products; and
Prefabricated components produced at site or near the
e) Testing of products.
site of work as possible.
9.1.3.3 Subsidia~ process
This system is normally adopted for a specific job order
for a limited period. Under this category there are two All other work involved in keeping the main production
types that is semi-mechanized and fully-mechanized. work to a cyclic working:
9.1.2.2.1 Semi-mechanized a) Storage of materials;
The work is normally carried out in open space with b) Transport of cement and aggregates;

14 NATIONAL BUILDING CODE OF INDIA


c) Transport of green concrete and reinforcement d) Better working conditions for the people on
cages; the job; and
d) Transport and stacking the precast elements; e) To minimize the effect of weather on the
e) Repairs and maintenance of tools, tackles and manufacturing schedule.
machines;
9.1.5 The various stages of precasting can be classified
f) Repairs and maintenance of moulds, and as in Table 2 on the basis of the equipments required
@ Generation of steam, etc. for the various stages. This permits mechanization and
9.1.4 For the manufacture of precast elements all the rationalization of work in the various stages. In the
above processes shall be planned in a systemat jc way precasting, stages 6 and 7 given in Table 2 form the
to achieve the following: main process in the manufacture of precast concrete
elements. For these precasting stages there are many
a) A cyclic technological method of working to technological processes to suit the concrete product
bring in speed and economy in manufacture; under consideration which have been proved rational,
b) Mechanization of the process to increase economical and time saving. The technological line or
productivity and to improve quality; process is the theoretical solution for the method of
c) The optimum production satisfying the planning the work involved by using machine
quality control requirements and to keep up complexes. Figure 5 illustrates diagrammatically the
the expected speed of construction aimed; various stages involved in a plant process.

WATER FINE COARSE CEMENT MILD STEEL H.T. WIRE


AGGREGATE AGGREGATE

TTY

& MIXING
+*
I
FILLING CONCRETE

T
COMPACTING
MOULD FITING
+

CURING 6
DETENBIONING
*

& CUt?lNG IN YARD

{ TESTING I
BY ROAO
-+&m--- ‘YMH

FIG. 5 PLANT PROCESS

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 15


Table 2 Stages of Precasting of Concrete Products
[Clauses 9.1.5 and 9.1 l(g)]

S1 Precasting Name of process Operatiom Involved


No. Stage No.
(1) (2) (3) (4)

i) 1 procurement and storage of Unloading and trrmsporl of cement, coarse and the aggregates, and steel, and
construction materials storing them in bins, silos or storage sheds
ii) 2 Testing of raw matcnals Testing of all materials including steel
iii) 3 Design of concrete mix Testing of raw ma~erials, plotting of grading curves and triat of mixes in
laboratory
iv) 4 Making of reinforcement cages Unloading of reinforcement bars from wagons or lorries and stacking them in
the steel yard, cutting, bending, tying or welding the reinforcements and
making in the form of a cage, which can be directly introduced into the mould.

v) 5 Applying form release agent and Moulds are cleaned, apptied with form release agent and assembled and placed
laying of moulds in position at the right place.
vi) 6 Placing of reinforcement cages, The reinforcement cages are placed in the mordds with spacers, etc as per data
inserts and fktures sheet prepared for the particular prefabricate.
vii) 7 Preparation of green concrete Taking out aggregates and cement horn bins, silos, etc. batching and mixing.
viii) 8 Transport of green concrete Tmnsport of green concrete from the mixer to the moulds. In the case of
precast method involving direct transfer of concrete from mixer to the mould
or a concrete hopper attached to the mould this prefabrication stage is not
necessary. .
ix) 9 Pouring and consolidation of Concrete is poured and vibrated to a good finish.
concrete

@ 10 Curing of concrete and demoulding Either a natural curing with water or an accelerated coring using steam curing
and other techniques. hr the case of steam curing using trenches or autoclaves,
this stage involves transport of motdds with the green concrete into the trench
or autoclave and taking them out after the curing and demoulding elements
cutting of protruding wires rdao falls in this stage. In certain cases the moulds
have to be partly removed and inserts, have to be removed after initial set. The
total demoulding is done after a certain period and the components are then
allowed to be cured. All these fall in this operation.
xi) 11 Stacking of precast elements Lifting of precast elements from the mould and transporting to the stacking
yard for further transport by tiler or rail is part of this stage.
xii) 12 Testing of finished components Tests are carried out on the components individually and in combination to
ensure the adequacy of their strength.
xiii) 13 Miscellaneous a) Oexreration of steam involving storing of coat or oil necessaxy for
generation of steam and providing insulated steam pipe connection up
to the various technological lines.
b) Repair of machines used in the production.

9.1.6 The various accepted methods of manufacture 9.2 Preparation and Storage of Materials
of precast units can be broadly classified into two Storage of materials is of considerable importance in
methods: the precasting industry, as a mistake in planning in this
a) The ‘Stand Method’ where the moulds remain aspect can greatly influence, the economics of production.
stationary at places, when the various From experience in constr@on, it is clear that there
processes involved are carried out in a cyclic will be very high percentages of loss of materials as well
order at the same place, and as poor quality due to improper storage and transport.
So, in a precast factory where everything is produced
b) The ‘Flow Method’ where the precast unit
with special emphasis on quality, proper storage and
under consideration is in movement according
preservation of building materials, especially cement,
to the various processes involved in the work
coarse and fine aggregates, is of prime importance.
which are carried out in an assembly-line
Storage of materials shall be done in accordance with
method.
Part 7 ‘Constructional Practices and Safety’.
The various accepted precasting methods are listed in
9.3 Moulds
Table 3 with details regarding the elements that can be
manufactured by these methods. 9.3.1 Moulds for the manufacture of precast elements

16 NATIONAL BUILDING CODE OF INDIA


Table 3 Precasting Methods
(Clauses 9.1,6 and 9.9.1)

SI Precasting Method Where Used Dimensions and Advantages and


No. Weights Remarks

(1) (2) (3) (4) (5)


-. . . .
O Individual Mould Method a) Ribbed slabs, beams, No limit in size and a) Strengttremng 01 the cmss-
(precasting method which may be girders, window weight. Depends on the section possible
easily assembled out of bottom and panels, box type units equipment used for b) Openings are possible in two
sides, transportable, if necessary. and special elements. demoulding, transporting planes
This may be either in timber or in b) Prestressed railway and placing
steel using needle or mould sleepers, parts of pre-
vibrators and capable of taking stressed girders, etc.
prestressing forces)

ii) Battery Form Method (The Interior wall panels, shell Length : 18m Specially suitable for mass
shattering panels may be adjusted elements, reinforced Breadth : 3 m production of wall panels where
into the form of a battery at the concrete battens, rafters, Mass : 5t shuttenng cost is reduced to a
required distances equal to the purlins and, roof and floor large extent and autoclave or
thickness of the concrete member) slabs trench steam curing may be
adopted by taking the steam
pipes through the shattering
psmels.

iii) Stack Method Ffoor and roof slab panels Length : Any desired For casting identical reinforced
M@ m P=timti panels one over
Breadth: lto4m the other with separating media
Mass : St interposed in between.

iv) Tilting Mould Method (This method Exterior wall panels Length : 6m Suitabie for manufacturing the
is capable of being skipped where special finishes are Breadth : 4 m external watt panels
vertically using hydraulic jacks) required on one face or Mass : 5t
for sandwich panel.

v) Long Line Prestressing Bed Method Double tees, ribbed slabs, Length : Any desired Ideafly suited for pretension
prrrlins, piles and beams Breadth : 2m members
Height : 2m
Mass : Upto lot

vi) Extrusion Method (Long concrete Roof slabs, foam concrete Length : Any desired May be used with advantage in
mould with constant cross-section wall panels and beams Breadth : Less than 2 m the case of on-reinforced blocks,
where concreting and vibration are cross-section where Height : Less than 3 m foam concrete panels
done automatically just as in hollow concreting and vibration
code slab casting) are done automatically
just as in hollow cored
slab casting.

may be of steel, timber, concrete and plastic or a 9.4 Accelerated Hardening


combination thereof. For the design of moulds for the
In most of the precasting factories, it is economical to
various elements, special importance should be given
use faster curing methods or artificial curing methods,
to easy demoulding and assembly of the various parts.
which in turn will allow the elements to be demoulded
At the same time rigidity, strength and watertightness
much earlier permitting early re-use of the forms. Any
of the mould, taking into consideration forces due to
of the following methods may be adopted:
pouring of green concrete and vibrating, are also
important. a) By Heating the Aggregates and Water Before
Mixing the Concrete — By heating of the
9.3.2 Tolerances aggregates as well as water to about 70”C to
The moulds have to be designed in such a way to take 80”C before making the concrete mix and
into consideration the tolerances given in 5. placing the same in the moulds, sufficiently
high earlier strengths are developed to allow
9.3.3 Slopes of the Mould Walls the elements to be stripped and transported.
For easy demoulding of the elements from the mould b) Steam Curing — Steam curing maybe done
with fixed sides, the required slopes have to be under high pressure and high temperature in
maintained. Otherwise there is a possibility of the an autoclave. This technique is more suited
elements getting stuck up with the mould at the time to smaller elements. Alternatively, this could
of demoulding. be done using low pressure steam having

PART 6 STRUCTUIL4LDESIGN — SECTION 7A PREFABRICATED CONCRETE 17


temperature around 80”C. This type of curing c) Pressed Concrete — This method is suitable
shall be done as specified in 9.5.2. For light for fabrication of smrdl or large products at
weight concrete products when steam cured high speed of production. A 100-200 tomes
under high pressure, the drying shrinkage is press compresses the wet concrete in rigid
reduced considerably, Due to this reason, high moulds and expels water. Early handling and
pressure steam curing in autoclave is specified a dense wear resistant concrete is obtained.
for light weight low densities ranging from d) Vacuum Treatment — This method removes
300 to 1000 kg/m3. For normal heavy the surplus air and water from the newly
concretes as well as light weight concretes of placed concrete as in slabs and similar
higher densities, low pressure steam curing elements. A suction up to about 70 percent of
may be desirable as it does not involve using an atmosphere is applied for 20 to 30 minutes
high pressures and temperatures requiring per centimetre thickness of the units.
high investment in an autoclave (see
e) Consolidation by Shock — Thk method is
also 9.5.2), suitable for small concrete units dropped
c) Steam Injection During Mixing of Concrete repeatedly from a height in strong moulds.
— In this method low pressure saturated The number of shocks required to remove
steam is injected into the mixer while the excess water and air may vary from 6 to 20
aggregates are being mixed. This enables the and the height of lift maybe up to as much as
heating up of concrete to approximately 60”C. half the depth of the mould.
Such a concrete after being placed in the
moulds attains high early strength. 9.4.3 After the accelerated curing of the above
Heated Air Method — In this method, the products by any of the above accepted methods, the
d)
concrete elements are kept in contact with hot elements shall be cured further by normal curing
air with a relative humidity not less than 80 methods to attain full final strength.
percent. Tlis method is specially useful for
9.5 Curing
light weight concrete products using porous
coarse aggregates. 9.5.1 The curing of the prefabricated elements can be
e) Hot Water Method — In this method, the effected by the normal methods of curing by sprinkling
concrete elements are kept in a bath of hot water and keeping the elements moist. This can also
water around 50°C to 80°C. The general be done in the case of smaller elements by immersing
principles of this type of curing are not much them in a specially made water tanks.
different from steam curing.
9.5.2 Steam Curing
f) Electrical Method — The passage of current
through the concrete panels generates heat 9.5.2.1 The steam curing of concrete products shall
through its electro-resistivity and accelerates take place under tarpaulin in tents, under hoods, under
curing. In this method, the concrete is heated chambers, in tunnels or in special autoclaves. The
up by an alternating current ranging from 50 steam shall have a uniform quality throughout the
volts for a plastic concrete and gradually length of the member. The precast elements shall be
increasing to 230 V for the set concrete. This so stacked, with sufficient clearance between each
method is normally used for massive concrete other and the bounding enclosure, so as to allow proper
products. circulation of steam.

9.4.1 After the accelerated hardening of the above Before the concrete products are subjected to any
products by any of the above accepted methods, the accelerated method of curing, the cement to be used
elements shall be cured further by normal curing shall be tested in accordance with accepted standards
methods to attain full final strength. (see Part 5 Building ‘Materials) especially for
soundness, setting time and suitability for steam curing.
9.4.2 Accelerated hardening may also be achieved by
the following techniques: In the case of elements manufactured by accelerated
curing methods, concrete admixtures to reduce the
a) Construction Chemicals — Suitable
construction chemicals may be used. water content can be allowed to be used. The normal
aeration agents used to increase the workability of
b) Consolidation by Spinning — Such a method
concrete should not be allowed to be used. Use of
is generally used in the centrifugal moulding
calcium chloride should be avoided for reinforced
of pipes and such units. The spinning motion
concrete elements.
removes excess water, effects consolidation
and permits earlier demoulding. 9.5.2.2 The surrounding walls, the top cover and the

18 NATIONAL BUILDING CODE OF INDIA


floor of steam curing chamber or tunnel or hood temperature should not be more than 60°C for
shall be so designed as not to allow more than concretes up to M 30 and 75°C for concretes greater
1 kcal/m2/h/OC. than M 45. In the case of light weight concrete, the
difference in temperature should not be more than 60”C
9.5.2.3 The inside face of the steam curing chamber,
for concretes less than M 25. For concretes greater
tunnel or hood shall have a damp-proof layer to
than M 50, the temperature differences can go up
maintain the humidity of steam. Moreover, proper
to 75”C.
slope shall be given to the floor and the roof to allow
the condensed water to be easily drained away. At first, 9.6 Stacking During Transport and Storage
when steam is let into the curing chambers, the air
Every precaution shall be taken against overstress or
inside shall be allowed to go out through openings
damage, by the provision of suitable packings at agreed
provided in the hoods or side walls which shall be
closed soon after moist steam is seen jetting out. points of support. Particular attention is directed to the
inherent dangers of breakage and damage caused by
9.5.2.4 It is preferable to let in steam at the top of the supporting other than at two positions, and also by the
chamber through perforated pipelines to allow uniform careless placing of packings (for example, not
entry of steam throughout the chamber. vertically one above the other). Ribs, comers and
9.5.2.5 The fresh concrete in the moulds should be intricate projections from solid section should be
allowed to get the initial set before allowing the adequately protected. Packing pieces shall not
concrete to come into contact with steam. The regular discolour, disfigure or otherwise permanently cause
heating up of fresh concrete product from about 20”C mark on units or members. Stacking shall be arranged
to 35°C should start only after a waiting period ranging or the precast units should be protected, so as to prevent
from 2 to 5 h depending on the setting time of cement the accumulation of trapped water or rubbish, and if
used. It may be further noted that steam can be let necessary to reduce the risk of efflorescence.
in earlier than this waiting period provided the 9.6.1 The following points shall be kept in view during
temperature of the concrete product does not rise
stacking:
beyond 35°C within this waiting period.
a) Care should be taken to ensure that the flat
9.5.2.6 The second stage in steam curing process is to
elements are stacked with right side up. For
heat up the concrete elements, moulds and the
identification, top surfaces should be clearly
surroundings in the chamber:
marked.
a) In the low pressure steam curing the airspace b) Stacking should be done on a hard and
around the member is heated up to a suitable ground to avoid any sinking of
temperature of 75°C to 80”C at a gradual rate, support when elements are stacked.
usually not faster than 30°C per hour. c) In case of horizontal stacking, packing
This process takes around 1 h to 1Y2h materials shall be at specified locations and
depending upon outside temperature. shall be exactly one over the other to avoid
b) In the case of curing under high pressure cantilever stress in panels.
steam in autoclaves, the temperature and d) Components — should be packed in a uniform
pressure are gradually built up during a period way to avoid any und-ue projection of
of about 4 h. elements in the stack which normally is a
source of accident.
9.5.2.7 The third stage of steam curing is to maintain
the uniform temperature and pressure for a duration 9.7 Handling Arrangements
depending upon thickness of the section, This may vary
9.7.1 Lifting and handliqg positions shall be clearly
from 3 h to 5% h in the case of low pressure steam
defined particularly where these sections are critical.
curing and 4 h to 7 h in the case of high pressure steam
Where necessary special facilities, such as bolt holes
curing.
or projecting loops, shall be provided in the units and
9.5.2.8 The fourth stage of steam curing is the gradual full instructions supplied for handling.
cooling down of concrete products and surroundings
9.7.2 For precast prestressed concrete members, the
in the chamber and normalization of the pressure to
residual prestress at the age of particular operation
bring it at par with outside air. The maximum cooling
of handling and erection shall be considered in
rate, which is dependent on the thickness of the
conjunction with any stresses caused by the handling
member, should normally not exceed 30”C per hour.
or erection of member. The compressive stress thus
9.5.3 In all these cases, the difference between the computed shall not exceed 50 percent of the cube
temperature of the concrete product and the outside strength of the concrete at the time of handling and

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 19


erection. Tensile stresses up to a limit of 50 percent 9.10 Erection
above those specified in Part 6 ‘Structural Design,
In the ‘erection of precast elements’, all the following
Section 5 Concrete’ shall be permissible.
items of work are meant to be included:
9.8 Identification and Marking a) Slinging of the precast element;
All precast units shall bear an indelible identification, b) Tying up of erection ropes connecting to the
location and orientation marks as and where necessary. erection hooks;
The date of manufacture shall also be marked on the c) Cleaning of the elements and the site of
units. erection;
9.8.1 The identification markings on the drawings d) Cleaning of the steel inserts before
shall be the same as that indicated in the manufacturer’s incorporation in the joints, lifting up of the
literature and shall be shown in a table on the setting elements, setting them down into the correct
schedule together with the length, type, size of the unit envisaged position;
and the sizes and arrangement of all reinforcement. e) Adjustment to get the stipulated level, line and
plumb;
9.9 Transport Welding of cleats;
f)
Transport of precast elements inside the factory and to @ Changing of the erection tackles;
the site of erection is of considerable importance not h) Putting up and removing of the necessary
only from the point of view of economy but also from scaffolding or supports;
the point of view of design and efficient management. Welding of the inserts, laying of reinforcements
j)
Transport of precast elements must be carried out with in joints and grouting the joints; and
extreme care to avoid any jerk and distress in elements
k) Finishing the joints to bring the whole work
and handled as far as possible in the same orientation
to a workmanlike finished product.
as it is to be placed in final position.
9.10.1 In view of the fact that the erection work in
9.9.1 Transport Inside the Factory
various construction jobs using prefabricated concrete
Transport of precast elements moulded inside the elements differs from place to place depending on the
factory depends on the method of production, selected site conditions, safety precautions in the work are of
for the manufacture as given in Table 3. utmost importance. Hence only those skilled foremen,
trained workers and fitters who have been properly
9.9.2 Transportfrom Stacking Yard Inside the Factory
instructed about the safety precautions to be taken should
to the Site of Erection
be employed on the job. For additional information, see
Transport of precast concrete elements from the factory Part 7 ‘Constructional Practices and Safety’.
to the site of erection should be planned in such a way
9.10.2 Transport of people, workers or visitors, by
so as to be in conformity with the traffic rules and
using cranes and hoists should be strictly prohibited
regulations as stipulated by the Authorities. The size
on an erection site.
of the elements is often restricted by the availability of
suitable transport equipment, such as tractor-cum- 9.10.3 In the case of tower rail mounted cranes running
trailers, to suit the load and dimensions of the member on rails, the track shall not have a slope more than
in addition to the opening dimensions under the bridge 0.2 percent in the longitudinal direction. In the transverse
and load carrying capacity while transporting the direction the rails shall lie in a horizontal plane.
elements over the bridge.
9.10.4 The track of the crane should be daily checked
9.9.2.1 While transporting elements in various to see that all fish plates and bolts connecting them to
systems, that is, wagons, trucks, bullock carts, care the sleepers are in place and in good condition.
should be taken to avoid excessive cantilever actions
9.10.5 The operation of all equipment used for
and desired supports are maintained. Special care
handling and erection shall follow the operations
should be taken at location of sharp bends and on
manual provided by the manufacturer. All safety
uneven or slushy roads to avoid undesirable stresses
precautions shall be taken in the operations of handling
in elements.
and erection.
9.9.2.2 Before loading the elements in the transporting
media, care should be taken to ensure that the base 10 EQUIPMENT
packing for supporting the elements are located at
10.1 General
specified positions only. Subsequent packings must be
kept strictly one over the other. The equipment used in the precast concrete industry/

20 NATIONAL BUILDING CODE OF INDIA


construction may be classified into the following a) With simple mechanization,
categories: b) With partial mechanization, and
a) Machinery required for quarrying of coarse c) With complex mechanization leading to
and fine aggregates; automation.
b) Conveying equipment, such as, belt conveyors, 10.2.1 In simple mechanization, simple mechanically
chain conveyors, screw conveyors, bucket operated implements are used to reduce the manual
elevators, hoists, etc; labour and increase the speed.
c) Concrete mixing machines; 10.2.2 In partird mechanization, the manual work is
d) Concrete vibrating machines; more or less eliminated in the part of a process. For
e) Erection equipment, such as, cranes, derricks, example, the batching plant for mixing concrete, hoists
hoists, chain pulley blocks, etc; to lift materials to a great height and bagger and
f) Transport machinery, such as, tractor-cum- bulldozer to do earthwork come under this category.
trailers, dumpers, lorries, locomotives, motor 10.2.3 In the case of complex mechanization leading
boats and rarely even helicopters; to automation, a number of processes leading to the
@ Workshop machinery for making and repairing end-product are all mechanized to a large extent
steel and timber moulds; (without or with a little manual or human element
h) Bar straightening, bending and welding involved). This type of mechanization reduces manual
machines to make reinforcement cages; work to the absolute minimum and guarantee the mass
Minor tools and tackles, such as, wheel production at a very fast rate and minimum cost.
j)
barrows, concrete buckets, etc; and 10.2.4 The equipment shall conform to accepted
k) Steam generation plant for accelerated curing. standards as listed in Part 7 ‘Constructional Practices
and Safety’.
In addition to the above, pumps and soil compacting
machinery are required at the building site for the 11 PREFABRICATED STRUCTURAL UNITS
execution of civil engineering projects involving
11.1 For the design and construction of composite
prefabricated components.
structures made up of prefabricated structural units and
Each of the above groups may further be classified cast in-situ concrete, reference may be made to good
into various categories of machines and further to practice [6-7A(3)].
various other types depending on the source of power
and capacity. 11.2 For design and construction of precast reinforced
and prestressed concrete triangulated trusses reference
10.2 Mechanization of the Construction and may be made to good practice [6-7A(4)].
Erection Processes
11.3 For design and construction of floors and roofs
The various processes can be mechanized as in any using various precast units, reference may be made to
other industry for attaining the advantages of mass good practice [6-7A(5)].
production of identical elements which in turn will
11.4 For construction with large panel prefabricates,
increase productivity and reduce the cost of production
reference may be made to good practice [6-7A(6)].
in the long run, at the same time guaranteeing quality
for the end-product. On the basis of the degree of 11.5 For construction of floors and roofs with joists
mechanization used, the various precasting factories and filler blocks, reference may be made to good
can be divided into three categories: practice [6-7A(7)].

LIST OF STANDARDS

The following list records those standards which are In the following list the number appearing in the first
acceptable as ‘good practice’ and ‘accepted standards’ column within parentheses indicates the number of the
in the fulfillment of the requirements of the Code. The reference in this Part/Section.
latest version of a standard shall be adopted at the time IS No. Title
of enforcement of the Code. The standards listed may (1) 2185 Specification for concrete
be used by the Authority as a guide in conformance masonry units:
with the requirements of the referred clauses in the (Part 1) :1979 Hollow and solid concrete
Code. blocks (second revision)

PART 6 STRUCTURAL DESIGN — SECTION 7A PREFABRICATED CONCRETE 21


IS No. Title IS No. Title
(Part 2): 1983 Hollow and solid light weight (2) 4905:1968 Methods for random sampling
concrete blocks (first revision) (3) 3935:1966 Code of practice for composite
(Part 3): 1984 Autoclave cellular aerated construction
concrete blocks (first revision) (4) 3201:1988 Criteria for design and
3201:1988 Criteria for design and construction of precast trusses
construction of precast trusses and purlins @-st revision)
and purlins @rst revision) (5) 6332:1984 Code of practice for construction
6072:1971 Specification for autoclave of floor and roofs using precast
reinforced cellular concrete wall doubly-curved shell units @-st
slabs revision)
6073:1971 Specification for autoclave 10297:1982 Code of practice for design and
reinforced cellular concrete construction of floors and
floor and roof slabs roofs using precast reinforced/
9893:1981 Specification for precast concrete prestressed concrete ribbed or
blocks for lintels and sills cored slab units

10297:1982 Code of practice for design and 10505:1983 Code of practice for construction
construction of floors and of floors and roofs using precast
roofs using precast reinforced reinforced concrete waffle units
prestressed concrete ribbed or 13994:1994 Code of practice for design and
cored slab unit construction of floor and roof
10505:1983 Code of practice for construction with precast reinforced concrete
of floors and roofs using precast planks and RC joists
concrete waffle units 14142:1994 Code of practice for design and
11447:1985 Code of practice for construction construction of floors and roofs
with large panel prefabricates with prefabricated brick panel

12440:1988 Specification for precast 14215:1994 Code of practice for construction


concrete stone masonry blocks of floor and roof with RC
channel units
13990:1994 Specification for precast
reinforced concrete planks and 14242:1994 Code of practice for design and
joists for flooring and roofing construction of roof with
L-Panel units
14143:1994 Specification for prefabricated
brick panel and partially precast (6) 11447:1985 Code of practice for construction
concrete joist for flooring and with large panel prefabricates
roofing (7) 6061 Code of practice for construction
14201:1994 Specification for precast of floor and roof with joists and
reinforced concrete channel unit hollow filler blocks:
for construction of floors and (Part 1): 1971 With hollow concrete filler
roofs blocks
14241:1994 Specification for precast (Part 2): 1981 With hollow clay filler blocks
L-Panel units for roofing (@W revision)

22 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section 7 Prefabrication, Systems Building and


Mixed/Composite Construction:
7B Systems Building and Mixed/Composite Construction

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 MATERIALS, PLANS AND SPECIFICATIONS ... 6
4 MODULAR CO-ORDINATION, ARCHITECTURAL TREATMENT AND ... 6
FINISHES
5 COMPONENTS ... 6
6 FORMWORK SYSTEMS ... 6
7 SYSTEM AND STRUCTURAL SCHEMES ... 6
8 JOINTS ... 8
9 TESTS FOR COMPONENTS/STRUCTURES .. 8
10 CONSTRUCTIONAL ASPECTS . .. 8
11 EQUIPMENT ... 8
12 PREFABRICATED STRUCTURAL UNITS . .. 8

ANNEX A CONSTRUCTION PRACTICE FOR DECKING . .. 8


ANNEX B CONSTRUCTION PRACTICE FOR CONCRETING ON DECKING ... 10

LIST OF STANDARDS ... 11

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

Systems building and mixed/composite construction is an upcoming field as far as its development and use in the
country is concerned. Two aspects specifically to be borne in mind are the system to be adopted for the different
categories of buildings and the sizes of their components. Here the principle of modular co-ordination is of value
and its use is recommended.

This section was first published in 1970 and was subsequently revised in 1983.

In this second revision, this section, earlier named as Prefabrication and Systems Building has been renamed and
restructured as follows:

Section 7 Prefabrication, Systems Buildings and Mixed/Composite Construction


7A Prefabricated Concrete
7B Systems Buildings and Mixed/Composite Construction

This sub-section covers systems building and mixed/composite construction, while such systems approach using
predominantly concrete as material for components is being dealt within sub-section 7A.

In this sub-section, an attempt has been made to prescribe general requirements applicable to all valid existing
systems and mixed/composite constructions as also to accommodate any new system introduced in the country
in future.

All standards cross referred to in the main text of this sub-section, are subject to revision. The parties to agreement
based on this sub-section are encouraged to investigate the possibility of applying the most recent editions of the
standards.

PART 6 STRUCTURAL DESIGN — SECTION ‘7B SYSTEMS BUILDING AND MIXED/COMPOSITE CONSTRUCTION 3
-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 6 STRUCTURAL DESIGN

Section
7 Prefabrication, Systems Building and
Mixed/Composite Construction:
76 Systems Building and Mixed/Composite Construction

1 SCOPE NOTE — The purposes of modular co-ordination are:


a) to reduce the variety of component sizes produced, and
This sub-section covers recommendations regarding b) to allow the building designer greater flexibility in the
modular planning, component sizes, joints, manufacture, arrangement of components.
storage, transport and erection of prefabricated
2.1.9 Modular Grid — A rectangular coordinate
elements for use in buildings and such related
reference system in which the distance between
requirements for systems building and mixed/
consecutive lines is the basic module or a multi-
composite construction.
module. This multi-module may differ for each of the
2 TERMINOLOGY three orthogonal dimensions of the grid, two in plan
and one in vertical direction.
2.1 For the purpose of this sub-section, the following
definitions shall apply. 2.1.10 Multi-module — A module whose size is a
selected multiple of the basic module.
2.1.1 Authority Having Jurisdiction — The Authority
which has been created by a statute and which, for the 2.1.11 Prefabricate — To fabricate components or
purpose of administering the Code/Part, may authorize assembled units prior to erection or installation in a
a committee or an official or an agency to act on its building.
behalfi hereinafter called the ‘Authority’.
2.1.12 Prefabricated Building — The partlylfully
2.1.2 Basic Module — The fundamental module used assembled and erected building, of which the structural
in modular co-ordination, the size of which is selected parts consist of prefabricated individual units or
for general application to building and its components. assemblies using ordinary or controlled materials,
NOTE — The value of the basic module has been chosen as
including service facilities; and in which the service
100 mm for the maximum flexibility and convenience. The equipment may be either prefabricated or constructed
symbol for the basic module is M. in-situ.
2.1.3 Cellular Concrete — The material consisting of 2.1.13 Sandwich Panels — Panels made by sandwiching
an inorganic binder (such as, lime or cement or both) a layer of insulation material between two outer layers
in combination with a finely ground material of hard durable materials like steel, dense concrete,
containing siliceous acid (such as sand), gas generating plastic, cement based sheet, ceramic, etc. The hard
material (for example, aluminium powder), water and coverings on two outer faces may be of same or
harmless additives (optional); and steam cured under different materials; the three layers being bonded with
pressure in autoclaves. each other to behave as a composite panel.
2.1.4 Components — A building product formed as a 2.1.14 Self-Compacting Concrete — Concrete that is
distinct unit having specified sizes in three dimensions. able to flow under its own weight and completely fill
2.1.5 Composite/Mixed Construction — Construction the voids within the formwork, even in the presence
involving two or more components, such as, of dense reinforcement without any vibration, whilst
prefabricated structural units of steel, prestressed maintaining homogeneity without segregation.
concrete or reinforced concrete and cast in-situ
2.1.15 Shear Connectors —’Structural elements, such
concrete, timber, masonry in brickwork and blockwork,
as anchors, studs, channels and spirals, intended to
glass and glazing connected together in such a manner
transmit the shear between the prefabricated member
that they act integrally.
and the cast in-situ concrete and also to prevent
2.1.6 Increments — Difference between two homologous separation at the interface.
dimensions of components of successive sizes.
2.1.16 System — The method of construction
2.1.7 Module — A unit of size used in dimensional of buildings with certain order and discipline
co-ordination. and repetitive operations using the prefabricated
2.1.8 Modular Co-ordination — Dimensional components, tunnel form or engineered shattering,
co-ordination employing the basic module or a multi- where the work is organized and follows a defined
module. procedure.

PART 6 STRUCTURAL DESIGN — SECTION 7B SYSTEMS BUILDING AND MIXED/COMPOSITE CONSTRUCTION 5


2.1.17 Unit — Building material formed as a simple very rapid construction. Accelerated curing if required
article with all three dimensions specified, complete is possible enabling early stripping of formwork.
in itself but intended to be part of a compound unit or
complete building. Examples are brick, block, tile, 6.2 Slipform
etc. Slipform is a continuously moving form at such a speed
that the concrete when exposed has already achieved
3 MATERIALS, PLANS AND SPECIFICATIONS
enough strength to support the vertical pressure from
3.1 Materials concrete still in the form as well as to withstand
nominal lateral forces. Slipform may be classified as
3.1.1 See Part 6 ‘Structural Design, Sub-section 7A
straight slipform, tapering slipform and slipform for
Prefabricated Concrete’, regarding materials and the
special applications. Construction of lift cores and
characteristics to be considered in their selection.
stairwell using slipform technique comes under special
3.1.2 The materials used in prefabricated components applications because of their complex sizes, shapes and
may be many and the modem trend is to use concrete, loads to be lifted alongwith the slipfonn like walkway
steel, treated wood, aluminium, cellular concrete, light truss, etc, which is essential for construction. This
weight concrete, ceramic products, etc. However, this system uses hydraulic jacks avoiding crane for lifting
section pertains to mixed/composite construction. of assembly during construction operation. This system
facilitates rapid construction and continual casting,
3.2 Plans and Specifications
creating a monolithic structure thereby avoiding
See Part 6 ‘Structural Design, Sub-section 7A construction joints.
Prefabricated Concrete’. ..
6.3 Aluminium Formwork
4 MODULAR CO-ORDINATION,
This system of formwork uses alurninium, which is
ARCHITECTURAL TREATMENT AND
light and rust free material, in both sheathing and
FINISHES
framework. It may be used for a broad range of
4.1 Modular Co-ordination applications from wall to slab construction panels to
more complicated structures involving bay windows,
See Part 6 ‘Structural Design, Sub-section 7A
stairs and hoods. Every component is light enough to
Prefabricated Concrete’.
be handled easily thereby minimizing the need for
4.2 Architectural Treatment and Finishes heavy lifting equipment.

See Part 6 ‘Structural Design, Sub-section 7A 6.4 Large Panel Shattering System
Prefabricated Concrete’.
This is a system, which gives an advantage of
5 COMPONENTS combining speed and quality of construction. The
vertical load carrying members are made of steel
5.1 The preferred dimensions of precast elements used
whereas the horizontal members are of plywood
and their casting tolerances shall be in accordance with
inserted into two wooden beams thereby forming a web
Part 6 ‘Structural Design, Sub-section 7A prefabricated
flange. All the formwork and support systems shall be
Concrete’.
designed for the loads coming during the actual
5.2 The permissible tolerances of timber used shall execution stage.
be in accordance with Part 6 ‘Structural Design, Sub-
section 3A Timber’. 6.5 Other/New Systems

5.3 For permissible tolerances of steel and masonry, Any otherlnew system may be used for systems
reference may be made to relevant Indian Standards. building after due exaihination and approval by the
Authority.
6 FORMWORK SYSTEMS
7 SYSTEM AND STRUCTURAL SCHEMES
The formwork systems which are utilized in buildings
shall be as given in 6.1 to 6.5. 7.1 Several schemes are possible, with certain
constraints, using the same set of components. The
6.1 Tunnel Form degree of flexibility varies from system to system.
However, in all the systems there is a certain order
This is a system which casts walls and slab together
and discipline.
like a portal in a single pour. Fagade walls are precast
or of block masonry to enable removal of tunnel form. 7.2 The following aspects, among others, are to be
All components are made up of steel. This produces considered in devising a system:

6 NATIONAL BUILDING CODE OF INDIA


a) Effective utilization of spaces; 7.3.1.3 Timber may be used as long span glue-
b) Straight and simple walling scheme; laminated beams and rafters, with precast concrete.
c) Limited sizes and numbers of components; Precast floors may be used in timber frame
construction. Similarly, timber frames with precast
d) Limited opening in bearing walls;
elements shall be used as a building system.
e) Regulated locations of partitions;
Standardized service and stair units; 7.3.1.4 Brick and block masonry may be combined
f)
with precast concrete structures and floors. The’ most
g) Limited sizes of doors and windows with
common combinations is to use prestressed floors on
regulated positions;
load bearing walls.
h) Structural clarity and efficiency;
j) Suitability for adoption in low and high rise 7.4 Design’ Considerations
building;
The mixed/composite structures shall be analyzed
k) Ease of manufacturing, storing and transporting; appropriately and the joints in them designed to take
m) Speed and ease of erection; and the forces of an equivalent discrete system. Resistance
n) Simple jointing system. to horizontal loading shall be provided by placing
beams, walls and bracings in two directions at right
7.3 Systems for Mixed/Composite Construction angles or otherwise. The individual components shall
The system of mixed/composite construction depends be designed, taking into consideration appropriate end
on the extent of the use of prefabricated components, conditions and loads at various stages of construction.
their materials, sizes and the technique adopted for their The components of the structure shall be designed for
manufacture and use in building. loads in accordance with Part 6 ‘Structural Design,
Section 1 Loads, Forces and Effects’. In addition,
7.3.1 Combinations of System Components for Mixe& members shall be designed for handling, erection and
Composite Construction impact loads that may be expected during handling
The following combinations may be used in mixedl and erection.
composite constriction: 7.4.1 For mixed and composite construction the
a) Structural steel work and timber roofs on following points shall be considered:
precast frames. a) Positions of stability cores, walls, bracing,
b) Precast floors onto steel and concrete beams, etc. — In high rise buildings the most popular
and masonry walls. method is a cast in-situ core constructed
c) Profiled metal decking on precast beams. several storeys ahead of the framework. In
d) Precast frames onto cast in-situ foundations, medium height buildings this may be precast
retaining walls, etc. concrete or brick infill, steel cross bracing or
e) Precast frames stabilized by masonry walls, precast concrete diagonal bracing.
steel bracing, etc. b) Maturity of connections — This may be
Precast cladding in steel or cast in-situ frames decisive for or alter planned site progress
9
and vice versa. unless it is properly managed. Cast in-situ
grouted joints need a few days of temporary
.!3) Glass curtain walling, stone cladding or metal propping unless combined mechanical
sheeting onto precast concrete frames, etc.
connections are also used.
h) Reinforced concrete and structural steel as
c) As a consequence of the above, the need to
composite columns and beams.
design some of the key components to achieve
7.3.1.1 Precast concrete may be combined with cast temporary stability.
in-situ concrete, often termed hybrid construction. Cast d) The availability andjor positioning of
in-situ is mostly used to form homogeneous connections equipments to transport and erect components
between precast elements and provide a structural — The size and weight of the various
topping for horizontal diaphragm action. In other cases components shall be organized to make
it is used to form the foundations and sub-structure to optimum use of crane capacity, for example,
the building. the lightest units farthest from the operating
7.3.1.2 Structural steelwork is largely used in long zone.
span prestressed concrete floors supported on rolled e) Erection safety and speed of construction,
and prefabricated steel beams and also as steel roof with attention to cast in-situ concreting
trusses supported on concrete columns. sequences — This is particularly important

PART 6 STRUCTURAL DESIGN — SECTION 7B SYSTEMS BUTLDING AND MIXED/COMPOSITE CONSTRUCTION 7


where fixing gangs are unaccustomed to 10.2 Decking
working with different materials.
Constructional practices relating to decking shall be
O Tolerances for economical construction — as given in Annex A.
This is particularly important where different
10.3 Concreting on Decking
manufacturers are producing components in
different materials. Concreting on decking shall be carried out in
accordance with Annex B.
7.4.2 Other design considerations and safety
requirements against progressive collapse shall be in 11 EQUIPMENT
accordance with Part 6 ‘Structural Design, Sub-section The requirements relating to equipment used in the
7A Prefabricated Concrete’. precast concrete construction shall be in accordance
with Part 6 ‘Structural Design, Sub-section 7A
8 JOINTS Prefabricated Concrete’.
Design of joints shall be in accordance with Part 6 12 PREFABRICATED STRUCTURAL UNITS
‘Structural Design, Sub-section 7A Prefabricated
12.1 For the design and construction of composite
Concrete’.
structures made up of prefabricated structural units and
9 TESTS FOR COMPONENTS/STRUCTURES cast in-situ concrete, reference may be made to good
practice [6-7B(1)].
Sampling procedure, testing on individual components
and load testing of structure shall be in accordance with 12.2 For design and construction of precast reinforced
Part 6 ‘Structural Design, Sub-section 7A Prefabricated and prestressed concrete triangulated trusses reference
may be made to good practice [6-7B(2)].
Concrete’.
12.3 For design and construction of floors and roofs
10 CONSTRUCTIONAL ASPECTS using various precast units, reference may be made to
10.1 Manufacture, Storage, Transport and Erection good practice [6-7B(3)].
of Precast Elements 12.4 For construction with large panel prefabricates,
reference may be made to good practice [6-7 B(4)].
The requirements relating to manufacture, storage,
transport and erection of precast concrete elements 12.5 For construction of floors and roofs with joists
shall be in accordance with Part 6 ‘Structural Design, and filler blocks reference may be made to good
Sub-section 7A Prefabricated Concrete’. practice [6-7B(5)].

ANNEX A

(Clause 10.2)

CONSTRUCTION PRACTICE FOR DECKING

A-1 RECEIVING, STORING AND LIFTING manufacturer. The information on each tag shall be
DECKING checked immediately upon arrival, to prevent incorrect
sheets being used, or unnecessary delays if changes
A-1.l Receiving Decking are necessary. In particular, the stated sheet thickness
Decking is packed by the manufacturer into bundles shall be checked against th~ requirement specified on
of up to 24 sheets, and the sheets are normally secured the drawings, and a visual inspection shall be made to
with metal banding. Each bundle may be up to 1 m ensure that there is no darnage.
wide (the width of a single sheet) by 750 mm deep, The bundles shall be lifted from the vehicle. Bundles
and may weigh up to 2.5 t, depending on sheet length shall never be off-loaded by tipping, dragging,
(average mass of sheet being about 1.5 t). Loads
dropping or other improvised means.
are normally delivered by articulated vehicles
approximately 16 m long with a maximum gross mass A-1.2 Storing Decking
of up to 40 t, and a turning circle of approximately
The decking shall not be delivered more than one
19 m. It shall be ensured that there is suitable access
month before its anticipated use, as it may be vulnerable
and appropriate standing and off-loading areas.
to abuse and damage if stored for longer periods on
Each bundle will be given an identification tag by the site. If it is not for immediate use, the decking shall be

8 NATIONALBUILDING CODE OF INDIA


stored on the steel frame. If this is not possible, it shall working platform by securely fixing the decking as
be located in an area where it will not be contaminated they progress.
by site traffic, and placed on bearers, which provide a
The laying of sheets shall begin at the locations
gentle slope to the bundle. This will allow any
indicated on the decking layout drawings. These would
condensation or rain to drain and a free flow of air
normally beat the comer of the building at each level,
around the bundle. Bundles shall not be stacked more
to reduce the number of ‘leading edges’, that is
than 4 m high, and no other materials shall be stored
unprotected edges where the decking is being laid.
on top of them. Bearers shall be placed between
When the bundles have been properly positioned, as
bundles, and positioned to prevent bending of the
provided above, there shall be no need to turn the sheets
sheets.
manually, and there shall be no doubt which way up
A-1.3 Lifting and Positioning the Decking the sheet shall be fixed,

The support steelwork shall be prepared to receive the Individual sheets shall be slid into place and, where
decking before lifting the bundles onto it. The top possible, fixed to the steelwork before moving onto
surface of the underlying beams shall be reasonably the next sheet. This will minimize the risk of an
clean. When through-deck welding of shear studs is accident occurring as a result of movement of a sheet
specified, the tops of the flanges shall be free of primer, when it is being used as a platform. However, for
paint and galvanizing. setting-out purposes, it maybe necessary to lay out an
entire bay using a minimum number of temporary
The identification tags shall be used to ensure that fixings before fully securing the sheets later.
bundles are positioned on the frame at the correct floor
Sheets shall be positioned to provide a minimum ..
level, and in the nominated bay shown on the deck
bearing of 50 mm on the steel support beams. The ends
layout drawing. The bundles shall be positioned such
of adjacent sheets shall be butted together. A gap of
that the interlocking side laps are on the same side.
up to 5 mm is generally considered not to allow
This will enable the decking to be laid progressively
excessive seepage, but, if necessary, the ends of the
without the need to turn the sheets. The bundles shall
sheets may be taped together. When end gaps are
also be positioned in the correct span orientation, and
greater than 5 mm, it is normally sufficient to seal them
not at 90° to it. Care shall be taken to ensure that the
with an expanding foam filler. The longitudinal edges
bundles are not upside down, particularly with
shall be overlapped, to minimize concrete seepage
trapezoidal profiles. For most trapezoidal decking
along the seams. Although not normrdly required, seam
profiles, the embossments shall be oriented so that they
fixings may be necessary in some circumstances.
project upwards.
Sheets projecting freely more than 600 mm shall be
Care is needed when lifting the decking bundles; avoided.
protected chain slings are recommended for the same.
If necessary, sheets shall be cut using a grinder or a
Unprotected chain slings can damage the bundle
nibbler. However, field cutting shall be kept to a
during lifting. When synthetic slings are used there
minimum and shall only be necessary where a column
is a risk of the severing them on the edges of the
or other obstruction interrupts the decking. Gaps
decking sheets.
adjacent to the webs of columns shall be filled in with
If timber packers are used, they shall be secured to the off-cuts or thin strips of steel. Decking sheets shown
bundle before lifting so that when the slings are as continuous on the decking layout drawing shall
released they do not fall to the ground (with potentially never be cut into more than one length. Also, sheets
disastrous results). Bundles shall never be lifted using shall never be severed at the location of a temporary
metal banding. support, and the decking shrdl never be fastened to a
temporary support.
A-2 DECK INSTALLATION
As the work progresses, scraps and off-cuts shall be
A-2.1 Placement of Decking disposed of in a skip placed alongside the appropriate
level of working. The skip shall be positioned carefully
Breaking open the bundles and installing the decking
over a support beam to avoid overloading the decking.
shall be done only when all the sheets can be positioned
If a skip is not available, scraps shall be gathered for
and secured. The decking layout drawing shall also be
collection as soon as is possible. Partially used bundles
checked to ensure that any temporary support that need
shall be secured, to avoid individual sheets moving in
to be in position prior to deck laying, is in place.
strong winds.
Access for installation may normally be achieved using
A-2.2 Fixing of Decking
ladders connected to the steel frame. Once the laying
out the sheets is started by erectors, they shall create Decking sheets shall be fixed to the top of the

PART 6 STRUCTURAL DESIGN — SECTION 7B SYSTEMS BUILDJNG AND MIXED/COMPOS~ CONSTRUCTION 9


supporting structure. All fixings shall be made through and placement of fasteners will normally be given on
the troughs in the decking. Fixings shall be at the decking layout drawing. Fixings shall not be made
approximately 300 mm centres (or in every trough) to temporary supports.
along the end supports, and at 600 mm centres (or in
alternate troughs) along the internal supports. As an The fixings, together with ‘through-deck’ welded studs
absolute minimum, each sheet shall be connected at (if present) normally provide lateral restraint to the
least twice to each permanent support. The number beams during the construction stages.

ANNEX B

(Clause 10.3)

CONSTRUCTION PRACTICE FOR CONCRETING ON DECKING

B-1 PLACING CONCRETE decking sheet are not balanced either side of the
intermediate support beam.
B-1.l Preparation
Stop ends, usually in the form of timber or plastic
Prior to beginning work on the decking, guardrails shall
inserts, are used to create the construction joints. As
be in position at all perimeters, internal edges and
with all the joints and ends of the decking, they shall
voids. The positions of any props (and back props)
be checked for potential grout loss.
shall be checked against the details shown on the
decking layout drawings to ensure that adequate B-1.4 Reinforcement
suppofi-has been provided.
All reinforcement shall be properly supported so that
B-1.2 Cleaning the Decking it does not get displaced during concreting. Plastic
stools, loops or preformed mesh may be used as
The surface of the decking shall be reasonably free of
‘chairs’, but not plastic channels, which can induce
dirt, oil, etc prior to concreting.
cracking. Chairs shall be robust. In particular, the
B-1.3 Construction Joints handling and movement of concrete carrying pipes
during pumping can cause significant local impacts
Although there is no technical limitation to the area on the reinforcement.
that may be concreted, the usual pour area is up to
1000 m2/day. Where the limits of the pour do not The reinforcement that has been fixed shall be checked.
coincide with permanent slab edges, construction joints Particular attention shall be given to checking any
are used to define the extent of the pour. additional bar reinforcement, such as may be needed
around openings.
The locations and details of the construction joints may
have an effect on the cracking. The layout and details B-1.5 Grout Loss
of the joints shall be determined by the structural The decking joints shall be closely butted and exposed
designer. For example, when brittle bonded finishes ends shall be ‘stopped’ wi~h proprietary filler pieces
are used, the relationship between the joints in the to avoid grout loss. Gaps greater than 5 mm shall be
concrete and the joints in the finishes shall be sealed.
considered at the outset, to reduce the risk of cracking
in undesirable locations. B-2 PLACEMENT

Where possible, the construction joints shall be located B-2.1 Concrete shall be placed in a way that minimizes
close to butt joints in the decking. Where shear the permanent deformation of the decking. This is
connectors are used, it is preferable to create the joint particularly important for spans greater than 3 m. When
to one side of the line of the shear connectors, to ensure concreting is progressed in the same direction as the
sound concrete around the studs. If the construction span of the decking (that is, parallel to the decking
joint cannot be made near a butt joint, it is suggested ribs), it shall be placed first over supports where the
that no more than one-third of the decking span from decking is continuous, followed by the mid-span region
a butt joint shall be left unpoured. Concreting shall and finally the areas above the end supports. When
not be stopped within a sheet length, because excessive concreting is progressed in a direction perpendicular
deflections may occur when the loads on a continuous to the decking span (that is, transverse to the decking

10 NATIONAL BUILDING CODE OF INDIA


ribs), it shall be placed first at the edge where a decking necessary for this operation, one to hold and
sheet is supported by the underlap of an adjacent sheet. manoeuvre the outlet pipe, the other to shovel away
This helps to ensure that longitudinal seams between excess concrete. No more than 4 workmen shall be
panels remain closed. present around the pipe outlet during pumping,
because of the potential for overloading the decking.
The concrete shall be well compacted, particularly near
The concrete shall not be dropped from the outlet
and around any shear connectors. This may be done
pipe onto the decking from a height of more than
using a vibrating beam, which may require adequate
about 1 m.
supports at either ends, or an immersion poker vibrator.
Hand tamping is not recommended as a way of B-2.3 Skipand Barrow
compacting the concrete, For slim floors with deep
Placing concrete from a skip hung from a crane may
decking, or for other partially encased beams, a poker
be difficult because of obstructions from beams and
is needed to ensure proper concrete flow around the
decking at higher floor levels. However, despite being
beams, beyond the ends of the decking.
time consuming, it is sometimes efficient to use the
B-2.2 Concrete Pumping skip and barrow technique for small infill bays.

Pumping may be adopted for both normal and Skips shall have a means of controlling the rate of
lightweight concrete mixes. Flow rates in the order of discharge, and shall not be discharged from more than
0.5 ms to 1 ms of concrete per minute maybe achieved, 0.5 m above the decking or barrow. When discharging
although, clearly, the longer the pump lines and the into a barrow, the barrow shall be supported by
higher the concrete is to be pumped, the slower the thick (about 30 mm) boards covering a 2 m x 2 m area,
.“
operation. A pump may normally lift the concrete up or by a finished part of the slab. Either provision
to 30 m. Secondary pumps, placed at intermediate limits impact loads. Barrows shall be run over thick
levels, may be necessary for higher lifts. boards placed on the mesh, which shall be supported
locally.
Pumplines are normally 150 mm in diameter and are
assembled in segments. As the force exerted at bends B-3 FINISHING, CURING AND DRYING
may be significant, straight line pumping is preferred.
If power floating is to be carried out, this shall be done
The lines shall be supported on timber blocks at
within 2 h to 3 h of casting. This allows time for the
intervals of 2 m to 3 m. Re-setting of pumplines is
concrete to harden sufficiently.
required at frequent intervals as the pour progresses.
This means that the outlet pipe shall be moved As the concrete is only exposed on one surface of a
frequently and carefully so that concrete heaping is composite floor, it can take longer than a traditional
minimized. A minimum of two operatives are reinforced concrete slab to dry out.

LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and’ accepted standards’ doubly-curved shell units (jlrst
in the fulfillment of the requirements of the Code. The revision)
latest version of a standard shall be adopted at the time
10297:1982 Code of practice for design
of enforcement of the Code. The standards listed may
and construction of floors and
be used by the Authority as a guide in conformance
roofs using precast reinforced/
with the requirements of the referred clauses in the
prestressed concrete ribbed or
Code.
cored units
IS No. Title 10505:1983 Code of practice for construction
(1) 3935:1966 Code of practice for composite of floors and roofs using
construction precast reinforced concrete
(2) 3201:1988 Criteria for the design and waffle units
construction of precast — trusses 13994:1994 Code of practice for design and
and purlins (first revision) construction of floor and roof
(3) 6332:1984 Code of practice for construction with precast reinforced concrete
of floor and roofs using precast planks and RC joists

PART 6 STRUCTURAL DESIGN — SECTION 7B SYSTEMS BUILDJNG AND MIXEWCOMPOSITE CONSTRUCTION 11


IS No. Title 1S No. Title

14142:1994 Code of practice for design and (4) 11447:1985 Code of practice for construction
construction of floors and roofs with large panel prefabricates
with prefabricated brick panel (5) 6061 Code of practice for construction
14215:1994 Code of practice for construction of floor and roof with joists and
of floor and roof with RC channel filler blocks:
units (Part 1): 1971 With hollow concrete filler
14242:1994 Code of practice for design and blocks
construction of roof with L-Panel (Part 2): 1981 With hollow clay filler blocks
units (first revision)

12 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY

BUREAU OF INDIAN STANDARDS


I

CONTENTS

FOREWORD ... 5

1 SCOPE ... 7

SECTION 1 CONSTRUCTIONAL PRACTICES

2 PLANNING, MANAGEMENT AND PRACTICES .!. 7

SECTION 2 STORAGE, STACKING AND HANDLING


PRACTICES

3 GENERAL . . 11
4 STORAGE, STACKING AND HANDLING OF MATERIALS ... 12
5 UNLOADING RAIL/ROAD WAGONS AND MOTOR VEHICLES ... 21

SECTION 3 SAFETY IN CONSTRUCTION OF


ELEMENTS OF A BUILDING

6 GENERAL ... 22
7 TERMINOLOGY ... 22
8 TEMPORARY CONSTRUCTION, USE OF SIDE WALLS AND ... 23
TEMPORARY ENCROACHMENTS
9 TESTING ... 23
10 INSPECTION AND RECTIFICATION OF HAZARDOUS DEFECTS . .. 23
11 FOUNDATIONS .. . 24
12 GENERAL REQUIREMENTS AND COMMON HAZARDS DURING ... 24
EXCAVATION
13 PILING AND OTHER DEEP FOUNDATIONS . .. 25
14 WALLS . .. 27
15 COMMON HAZARDS DURING WALLING .. . 28
16 ROOFING . .. 29
17 ADDITIONAL SAFETY REQUIREMENTS FOR ERECTION OF . .. 30
CONCRETE FRAMED STRUCTURES (HIGH-RISE BUILDINGS)
18 ADDITIONAL SAFETY REQUIREMENTS FOR ERECTION OF . .. 33
STRUCTURAL STEEL WORK
19 MISCELLANEOUS ITEMS . .. 36
20 FINISHES ... 38
21 FRAGILE FIXTURES ... 38
22 SAFETY IN SPECIAL OPERATIONS . .. 38
23 ELECTRICAL INSTALLATIONS AND LEWS ... 38
24 GENERAL REQUIREMENTS .. . 38
25 CONSTRUCTION MACHINERY .. . 40

SECTION 4 MAINTENANCE MANAGEMENT, REPAIRS, RETROFllTING


AND STRENGTHENING OF BUILDINGS

26 MAINTENANCE MANAGEMENT ... 40

2 NATIONAL BUILDING CODE OF INDIA


27 PREVENTION OF CRACKS ... 46
28 REPAIRS AND SEISMIC STRENGTHENING OF BUILDINGS ... 47

SECTION 5 SAFETY IN DEMOLITION OF BUILDINGS

29 GENERAL ... 48
30 PRECAUTIONS PRIOR TO DEMOLITION ... 49
31 PRECAUTIONS DURING DEMOLITION ... 50
32 SEQUENCE OF DEMOLITION OPERATIONS ... 50
33 WALLS ... 50
34 FLOORING ... 50
35 DEMOLITION OF STEEL STRUCTURES ... 50
36 CATCH PLATFORM . .. 51
37 STAIRS, PASSAGEWAYS AND LADDERS ... 51
38 MECHANICAL DEMOLITION ... 51
39 DEMOLITION OF CERTAIN SPECIAL TYPES AND ELEMENTS OF ... 51
STRUCTURES
40 LOWERING, REMOVAL AND DISPOSAL OF MATERIALS ... 52
41 MISCELLANEOUS ... 53
42 FIRST-AID ... 53

ANNEX A PROGRAMME EVALUATION AND REVIEW TECHNIQUE, . .. 54


AND CRITICAL PATH METHOD
ANNEX B CHECK LIST FOR STACKING AND STORAGE OF MATERIALS ... 55
ANNEX C COMMON CAUSES FOR MAINTENANCE PROBLEMS ... 56
ANNEX D FORMAT FOR INSPECTION REPORT ... 57
ANNEX E GUIDELINES FOR MAINTENANCE OF ELECTRICAL ... 58
EQUIPMENTS

LIST OF STANDARDS ... 60

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY


-,
(J 6$
National Building Code Sectional Committee, CED 46

FOREWORD

This Part of the Code emphasizes the importance of carrying out all constructional operations in a safe and
efficient manner. Workers in large number, both skilled and unskilled, are engaged in the innumerable construction
works. Due to increased tempo of such a building activity and large scale mechanization, hazards of accidents
could increase considerably. It is, therefore, imperative that adequate safety rules are laid down for every phase
of construction work.
Planning the various constructional operations before hand and making adequate arrangements for procurement
and storage of materials, and the machinery to get work done is as important as carrying out these constructional
operations in accordance with good practice. Lack of planning or defective planning may result in avoidable
delay in the completion of work and consequently increased hazards from the point of view of fwe, health and
structural soundness.
The first version of this Part was prepared in 1970, which was subsequently revised in 1983. In the first revision,
information regarding handling operations, that is unloading, stacking, lifting, loading and conveying of building
materials, was also given along with the storage practices. Additional information regarding the use of ladders;
safety requirements for floor and wall openings, railings and toe boards; piling and other deep foundations;
constructions involving use of hot bituminous materials; and erection of structural steel work and concrete framed
structures, etc, were included.
As a result of experience gained in implementation of 1983 version of this part and feedback received as well as
in view of formulation of new standards in the field of constructional practices and safety and revision of some
existing standards, a need to revise this Part was felt. This revision has, therefore, been prepared to take care of
these aspects. The significant changes incorporated in this revision include:
a) The Section 1 Constructional Practices have been revamped and now includes the Planning and
Management aspects.
b) The provisions with regard to stacking and storage of building materials and components have been
updated and comprehensively covered in line with IS 4082: 1996. This revision now also covers
provisions for materials like stones, blocks, roof tiles, partially prefabricated wall and roof components,
cinder, aluminium section, cast iron and aluminium sheets, plastic sheets, doors and windows, etc.
c) Provisions on constructional practices using bamboo have been included.
d) Provisions of safety requirements of hoistsflifts for worker during construction have been added.
e) Provisions with regard to safety at work site have been detailed incorporating aspects like preventive
measures, such as, falling material hazards prevention, fall prevention, disposal of debris, fire protection,
etc.
f,) Provisions regarding safety management at work sites have been added.
g) A new section on ‘Maintenance management, repairs, retrofitting and strengthening of buildings’ has
been added, covering aspects like maintenance management, prevention of cracks, and repairs and
seismic strengthening of buildings.
h) Safety provisions with respect to demolition of buildings have been updated.
j) Reference to all the concerned Indian Standards have been updated.

Bamboo is a versatile renewable resource having low gestation period, characterized by high strength, low mass
and ease of working with simple tools. Resilience coupled with lightness makes it suitable for housing in
earthquake-prone and disaster-prone areas. It has the capacity to absorb more energy and shows larger deflections
before collapse and as such is safer under earth tremors. In this revision of this Part, therefore, provisions on
construction using bamboo have been incorporated. The structural design aspects are covered in Part 6 ‘Structural
Design, Section 3 Timber and Bamboo, 3B Bamboo’.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 5


The information contained in this Part is largely based on the following Indian Standards and Special Publications:

IS No. Title
3696 Safety code for scaffolds and ladders:
(Part 1): 1987 Scaffolds
(Part 2): 1991 Ladders
3764:1992 Code of practice for excavation work @-st revision)
4082:1996 Recommendations on stacking and storage of construction materials and components
at site (second revision)
4130:1991 Safety code for demolition of buildings (second revision)
4912:1978 Safety requirements for floor and wall ope&ngs, railing and toe boards (fh-st revision)
5121:1969 Safety code for piling and other deep foundations
5916:1970 Safety code for construction involving use of hot bituminous materials
7205:1974 Safety code for erection of structural steel work
7969:1975 Safety code for handling and storage of building materials
8989:1978 Safety code for erection of concrete framed structures
13415 ; 1992 Safety code for protective barrier in and around buildings
13416 Recommendations for preventive measures against hazards at work places:
(Part 1): 1992 Falling material hazards prevention
(Part 2): 1992 Fall prevention
(Part 3): 1994 Disposal of debris
(Part 4): 1994 Timber structures
(Part 5): 1994 Fire protection
13430:1992 Code of practice for safety during additional construction and alteration to existing
buildings

A reference to SP 62:1992 ‘Handbook on building construction practices (excluding electrical works)’ and
SP 70:2001 ‘Handbook on construction safety practices’ may also be made.

All standards, whether given herein above or cross referred to in the main text of this Part, are subject to revision.
The parties to agreement based on this Part are encouraged to investigate the possibility of applying the most
recent editions of the standards.

NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY

1 SCOPE special considerations and meticulous planning due to


restricted space, adjoining structures, underground
This Part of the Code covers the constructional
utilities, traffic restrictions, noise and other
planning, management and practices in buildings;
environmental pollution and other specific site
storage, stacking and handling of materials and safety
constraints,
of personnel during construction operations for all
elements of a building and demolition of buildings. It 2.1.1.4 The constructability aspects of the proposed
also covers guidelines relating to maintenance construction methods needs to be carefully evaluated
management, repairs, retrofitting and strengthening of at the planning stage to ensure ease of construction
buildings. besides optimizing the construction schedule and
achieving quality, reliability and maintainability of the
SECTION 1 CONSTRUCTIONAL constructed facilities.
PRACTICES
2.1.1.5 Constructional practices in hilly regions needs
2 PLANNING, WAGEMENTAND PRACTICES to take into considerations the problem of landslides,
slope stability, drainage, etc, besides ensuring no
2.1 Planning Aspects
adverse impact on the fragile environmental conditions.
Construction planning aspects aim to identify and
2.1.1.6 Durability of constructions in corrosive
develop various stages of project execution on site
atmospheric conditions like coastal regions and
which should be consistent with the management
aggressive ground situations with high chlorides and
considerations. Planning aspects evolve out of the
sulphates should also be @en care of with appropriate
objectives of project and requirements of the final
constructional practices.
completed constructed facility. These objectives could
relate to the final constraints, cost considerations, 2.1.1.7 Constructional practices in disaster prone areas
quality standards, safety standards, environmental need specific planning. The type of construction, use
considerations and health considerations. Construction of materials, construction techniques require special
practices would, then have to satisfy these objectives considerations in such areas.
during construction phase of the project.
2.1.1.8 Adverse weather conditions have strong
Having established objectives of the construction bearing on construction phase. Situations wherein
phase, planning determines processes, resources constructions are to be carried out in adverse weather
(including materials, equipments, human and conditions, such as heavy and continuous rain fall,
environmental) and monitoring system to ensure that extreme hot or cold weather, dust storms, etc, the
the practices are appropriately aligned. Adequate practices have to address the relevant aspects.
knowledge about pre-construction phase evolution of Accordingly, suitable design and field operations
project, especially related to customer’s requirements, should be adapted or redefined in anticipation of these
is an essential prerequisite for construction planning. aspects. Some of these aspects are:
2.1.1 Preconstruction Phase a) Site layout which enables accessibility in
2.1.1.1 Besides the design aspects, preconstruction adverse weather.
phase should also address all the issues related to the b) Adequate protected storage for weather
implementation of the design at the site through suitable sensitive materipls/equipments.
construction strategy. During the design stage, the site c) Protections to personnel from extreme hot/
conditions should be fully understood with anticipated control conditions.
difficulties and avoid the risk of subsequent delays and
d) Scheduling to allow maximization of outdoor
changes after the construction has started.
activities during fair weather conditions.
2.1.1.2 The selection of construction methods, e) Special design and construction provisions for
building systems and materials, components, activities in extreme temperature conditions
manpower and equipments and techniques are best like hot or cold weather concreting, staple of
done in the preconstruction phase. Such selection is false work in extreme wind conditions (gusts).
influenced by the local conditions like terrain, climate, Adequate lighting for shorter days in winter/
f)
vulnerability for disasters, etc. night work.
2.1.1.3 Construction in busy localities of cities needs g) Design for early enclosure.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 7


r
2.1.2 Resource Planning planned keeping in view the various requirements to
construction activities and the specific constraints in
Resource planning aims to identify requirement,
terms of its size, shape, topography, traffic and other
availability and regulatory/control processes related to
restrictions, in public interest. A well planned site
resources. Resource planning is a generic expression
layout would enable safe smooth and efficient
but the actual process of planning is specific to the
construction operations. The site layout should take
resources considered.
into considerations the following factors:
In construction phases, the resources could be
a) Easy access and exit, with proper parking of
categorized as materials, manufactured products,
vehicle and equipments during construction.
equipments for construction, installation and
b) Properly located material stores for easy
fabrication, human resources as a part of overall
handling and storage.
organization, information resources, such as, reference
standards and other practice documents, environmental c) Adequate stack areas for bulk construction
conditions for work on site and infrastructure facilities. materials.
Therefore, the resource planning encompasses d) Optimum location of plants and equipments
identification, estimation, scheduling and allocation of (batching plants, etc).
resources. Resource planning needs to establish e) Layout of temporary services (water, power,
a control system for controlling consumption power suppression unit, hoists, cranes,
monitoring, corrective action and resource reappropriation elevators, etc).
in the event of favorable deviation. Organizational Adequate yard lighting and lighting for night
f)
capability, commitment to the project requirements and shifts. -.
other constraints such as time and cost, need to be
g) Temporary buildings; site office and shelter
considered as inputs while planning resources.
for workforce with use of non-combustible
Techniques of management and planning, such as,
materials as far as possible including
Programme Evaluation and Review Technique (PERT)
emergency medical aids.
and Critical Path Method (CPM) (see Annex A) may
h) Roads for vehicular movement with effective
be used.
drainage plan.
Non-availability of basic building materials (brick, Construction safety with emergency access
j)
stone aggregate, etc) within reasonable lead would and evacuations and security measures.
influence the constructional practice by alternative
k) Fabrication yards for reinforcement
materials. The constructional practices also get
assembly, concrete precasting and shattering
decided by the local skills of the manpower for
materials.
constructional activities. The equipment selection
m) Fencing, barricades and signages.
would also be governed by the site constraints.
Therefore, as, the resource planning is critical to the 2.1.3.3 Access for fire fighting equipment vehicles
project viability itself, the inputs to the resource
planning need to be validated appropriately and Access for fire fighting equipment shall be provided
established for such management. Resource planning to the construction site at the start of construction and
should establish a proper system of data collection maintained until all construction work is completed.
so as to facilitate effective resources control 2.1.3.3.1 Free access from the street to fire hydrants/
mechanism. Resource planning responsibility has to static water tanks, where available, shall be provided
be specifically defined in the overall organizational and maintained at all times.
setup.
2.1.3.3.2 No materials for construction shall be placed
2.1.3 Construction Phase within 3 m of hydrants/static water tanks.
2.1.3.1 Organizational structure 2.1.3.3.3 During building operations, free access to
The site management should be carried out through permanent, temporary or portable fust-aid fire fighting
suitable site organization structure with roles and equipment shall be maintained at all times.
responsibilities assigned to the construction personnel
2.L3.4 Access to the upper$oors during construction
for various construction related functions. Safety
management is one of the important components of In all buildings over two storeys high, at least one
site management. stairway shall be provided in usable condition at all
times. This stairway shall be extended upward as each
2.1.3.2 Site layout
floor is completed. There shall be a handrail on the
The layout of the construction site should be carefully staircase.

8 NATIONAL BUILDING CODE OF INDIA


2.1.3.5 Construction strategy and construction and men through one or more construction agencies.
sequence To fulfil the construction scope with quality, in time
and under safe conditions within a reasonable cost, it
Construction strategy and construction methods are to
is desired that the project is planned for managing
be evolved at the planning and design stage specific to
construction for amalgamation of above resources for
the conditions and constraints of the project site and
their optimum use and its continuous monitoring.
implemented by the site management personnel to
Agencies managing the supervision andlor construction
ensure ease of construction and smooth flow of
are desired to plan and document a management system
construction activities. Sites of high water table
with clear cut responsibilities and for managing various
conditions with aggressive chemical contents of subsoil
parameters like scope, time, quality, health, safety and
needs special design considerations. Buildings with
environment and cost for implementation, monitoring
basement in sites of high water table should be planned
and control for their effectiveness. This may be
with clewatering scheme with appropriate construction
preferably inline with proven National/International
sequence, Duration of dewatering should continue till
documentation system covering all aspects of
sufficient dead loads are achieved to stabilize the
monitoring and controls. Various parameters to be
buoyancy loads with adequate factor of safety. The
managed during construction are as below.
construction sequence should be planned taking into
consideration the following aspects: 2.2.1 Time Management

a) Availability of resources (men, material and Considering the importance of time in a project, it is
equipment); desirable that project is completed in the defined time
b) Construction methods employed including schedule to get its fruitful benefits. The system planned
prefabrication; should cover total schedule of completion with one or
more construction agencies, number of vendors,
c) Planned construction time;
identification of total resources, timely availability of
d) Design requirements and load transfer
all inputs, including critical ones, its processing during
mechanism;
construction of a project. The system should include a
e) Stability of ground like in hilly terrain; periodic review of a project with all parameters as well
f) Ensuring slope stability with retaining as catchup plans in case of delay identified for controls
structure before the main construction; and reporting from time to time. The system planned
g) Installation and movement of heavy should preferably be computer friendly and simple to
equipments like cranes and piling equipments; follow for implementation, monitoring and controls
h) Effect of weather; and and for reporting from time-to-time.

j) Minimum time to be spent below ground level 2.2.2 Quality Management


working.
Quality of a project should be planned for all activities
2.1.4 Scope Management from inception to completion. It is desirable that the
system planned gives adequate assurance and controls
Construction management efforts should ensure that that it shall meet project quality objectives. The system
the project features and functions that characterise the shall cover review of existing requirements, sub-
project scope remain as established during the design contracting, materials, processes and controls during
finalization stage. Accordingly, construction phase process, auditing, training of personnel, final inspection
practices need to be oriented to manage the project and acceptance. All activities shall be planned and
scope. As a part of overall project scope management controlled. Quality systems approach may be referred
functions, the processes of scope planning, scope for planning, suitable to a particular project for
definition and scope verification are associated with implementation.
the preconstruction phase of the project. The scope
monitoring and the change control are critical to the 2.2.3 Health, Safety and Environment
construction phase leading to serious implications on Each project affects the safety and health of the
the time and cost aspects. In this respect, consolidated workmen and surroundings during construction.
brief of the project established at the end of the design Various activities having impact on health, safety and
completion is an essential reference for scope baseline. environment need to be identified with their likely
effect and proposed preventive corrective actions,
2.2 Construction Management
together with the concerned statutory obligations. The
Construction phase of the project transfers the project system planned for health, safety and environment shall
conceived on paper in the form of plans and designs, address and cover the above including use of personnel
into reality by use of resources like materials, machines protective equipments by all concerned, and reporting

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 9


on their monitoring and controls during project machete, hack saw, axe, hatchet, sharpening tools,
implementation. adze, chisel (20 mm), chill, wood rasps, steel rod, and
pliers, will greatly increase the effectiveness of the
2.2.4 Cost Management
construction process.
To keep the project under viable proposition, it is
2.3.3.2.3 For providing safety to the structure against
desired that cost of the project during construction are
fire, bamboo may be given fire retardant treatment
monitored and controlled through a documentation
using following chemicals; a few drops of concentrated
system. The various parameters which may affect the
HC1 shall be added to the solution to dissolve the
basic cost, escalations, cost due to variation in scope
precipitated salts:
and quantities, etc need to be monitored at a defined
frequency. The system planned may be in line with a Ammonium phosphate 3 parts
proven cost control method or similar in nature and Bone acid 3 parts
cost incurred vis-a-vis cost sanctioned and cost Copper sulphate 1 part
anticipated to be reported and controlled from time to
Zinc chloride 5 parts
time.
Sodium bichromate 3 parts
2.3 Construction Control and Practices Water 100 parts
2.3.1 Professional Services and Responsibilities 2.3.3.2.4 Foundations
The responsibility of professionals with regard to Bamboo indirect contact with ground, bamboo on rock
planning designing and supervision of building or preformed concrete footing, bamboo incorporated
construction work, etc and that of the owner shall be into concrete or bamboo piles may form the foundation
in accordance with Part 2 ‘Administration’. All structure (see Fig. 1).
applications for permits and issuance of certificates,
etc shall be as given in Part 2 ‘Administration’. 2.3.3.2.5 Floors
Employment of trained workers shall be encouraged The floor of bamboo may be at ground level with
for building construction activity. covering of bamboo matting, etc. In elevated floors,
2.3.2 Construction of all Elements bamboo members become an integral part of structural
framework of building. The floor will comprise
Construction of all elements of a building shall be in structural bamboo elements and bamboo decking.
accordance with good practice [7(1)]. Constructional
aspects using bamboo shall be as given in 2.3.3. It shall 2.3.3.2.6 Jointing Techniques
also be ensured that the elements of structure satisfy The jointing techniques in construction using bamboo
the appropriate fire resistance requirements as specified shall be in accordance with Part 6 ‘Structural Design,
in Part 4 ‘Fire and Life Safety’, and quality of building Section 3 Timber and Bamboo, 3B Bamboo’.
materials/components used shall be in accordance with
Part 5 ‘Building Materials’. 2.3.4 Low Income Housing

2.3.3 Construction Using Bamboo For low income housing, appropriate planning and
selection of building materials and techniques of
2.3.3.1 Bamboo being a versatile resource characterized
construction have to be judiciously done and applied
by high strength, low mass and ease of working with
in practice. Requirements of low income housing
simple tools, it is desirable to increasingly make
specified in Part 3 ‘Development Control Rules and
appropriate use of this material. Design of structures
General Building Requirements’, shall be followed.
using bamboo shall be done in accordance with
However, all requiremerlfs regarding structural safety,
Part 6 <Structural Design, Section 3 Timber and
health safety and fire safety shall be in accordance with
Bamboo, 3B Bamboo’. For construction using bamboo,
this Code.
some of the important constructional provisions given
in 2.3.3.2 to 2.3.3.6 shall be followed. 2.3.5 Site Preparation
2.3.3.2 Working finishing While preparing the site for construction, bush and
2.3.3.2.1 Bamboo can be cut and split easily with very other wood, debris, etc, shall be removed and promptly
simple hand tools. Immature bamboos are soft, pliable disposed of so as to minimize the attendant hazards.
and can be moulded to desired shape. It takes polish
Temporary buildings for construction offices and
and paint well.
storage shall be so located as to cause the minimum
2.3.3.2.2 While it is possible to walk with bamboo fire hazards and shall be constructed from non-
simply using a machete, a few basic tools, such as, combustible materials as far as possible.

10 NATIONAL BUILDING CODE OF INDIA


4

lB BAMBOO INCORPORATED INTO CONCRETE


1A BAMBOO ON PREFORMED
FOOTINGS (SINGLE POST FOOTING)
CONCRETE FOOTINGS

lC BAMBOOOUTOFGROUNDCONTACTONSTRIPFOOTINGS OFCONCRETE(LARGE
DIAMETERTHICK WALLED BAMBOO WITHCLOSELYSPACED NODESTOBEUSED)

FIG. 1 BANIEiOOFOUNDATIONS

2.3.6 UseojNew/Alternati~.eConstruction Techniques the layout for stacking and storage of different
materials, components and equipments with proper
The provisionsof thispartarenot intendedtoprevent
access and proper manoeuvrability of the vehicles
use of any construction techniques including any
carrying the material. While planning the layout, the
alternative materials, nonspecifically prescribed bythe
requirements of various materials, components and
Code,providedany suchalternativehas beenapproved.
equipments at different stages of construction shall be
The Authority may approve any such alternative such
considered.
as ferrocement construction, row-lock (rat trap) bond
;n masonry, stretcher bond in filler slab and filler slab 3.1.2 Materials shall be segregated as to kind, size and
provided it is found that the proposed alternative is length and placed in neat, orderly piles that are safe
satisfactory and conforms to the provisions of relevant against falling. If piles are high they shall be stepped
parts regarding material, design and construction and back at suitable intervals in height. Piles of materials
that material, method, or work offered is, for the shall be arranged so as to allow a passageway of not
purpose intended, at least equivalent to that prescribed less than 1 m width in between the piles or stacks for
in the Code in quality, strength, compatibility, inspection or removal. All passageways shall be kept
effectiveness, fire and water resistance, durability and clear of dry vegetation.
safety.
3.1.3 Materials shall be stored, stacked and handled
in such a manner as to prevent deterioration or intrusion
SECTION 2 STORAGE, STACKING AND
of foreign matter and to ensure the preservation of their
HANDLING PRACTICES
quality and fitness for the work.
3 GENERAL 3.1.4 Materials shall be stacked on well drained, firm
and unyielding surface. Materials shall not be stacked
3.1 Planning and Storage Layout
so as to impose any undue stresses on walls or other
3.1.1 For any site, there should be proper planning of structures.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 11


3.1.5 Materials shall be stacked in such a manner as [7(3)] shall be followed for handling and usage asbestos
not to constitute a hazard to passerby. At such places cement products.
the stacks shall have suitable warning signs in daytime
4.2 Cement
and red lights on and around them at night.
a) Storage and Stacking — Cement shall be
3.1.6 Stairways, passageways and gangways shall not
stored at the work site in a building or a shed
become obstructed by storage of building materirds,
which is dry, leakproof and as moisture-proof
tools or accumulated rubbish.
as possible. The building or shed for storage
3.2 Protection Against Atmospheric Agencies should have minimum number of windows
and close fitting doors and these should be
Materials stored at site, depending upon the individual kept closed as far as possible.
characteristics, shall be protected from atmospheric
Cement received in bags shall be kept in such
actions, such as rain, sun, winds and moisture, to avoid
a way that the bags are kept free from the
deterioration.
possibility of any dampness or moisture
3.3 Manual Handling coming in contact with them. Cement bags
shall be stacked off the floor on wooden
When heavy materials have to be handled manually planks in such a way as to keep them about
each workman shall be instructed by his foreman or 150 mm to 200 mm clear above the floor. The
supervisor for the proper method of handling such floor may comprise lean cement concrete or
materials. Each workman shall be provided with two layers of dry bricks laid on a well
suitable equipment for his personal safety as necessmy. consolidated earth. A space of 600 mm
Supervisors shall also take care to assign enough men minimum shall be left alround between the
to each such job depending on the weight and the exterior walls and the stacks (see Fig. 2). In
distance involved. the stacks the cement bags shall be kept close
together to reduce circulation of air as such
3.4 Protection Against Fire and Other Hazards
as possible. Owing to pressure on bottom
3.4.1 Materials, like timber, bamboo, coal, paints, etc, layer of bags sometimes ‘warehouse pack’ is
shall be stored in such a way that there may not be any developed in these bags. This can be removed
possibility of fire hazards. Inflammable materials like easily by rolling the bags when cement is
kerosene and petrol, shall be stored in accordance with taken out for use. Lumped bags, if any should
the relevant rules and regulations so as to ensure the be removed and disposed off.
desired safety during storage. Stacks shall not be piled The height of stack shall not be more than 10
so high as to make them unstable under fire fighting bags to prevent the possibility of lumping up
conditions and in general they shall not be more than under pressure. The width of the stack shall
4.5 m in height. The provisions given in good practice be not more than four bags length or 3 metres.
[7(2)] shall be followed. Explosives like detonators In stacks more than 8 bags high, the cement
shall be stored in accordance with the existing bags shall be arranged alternately length-wise
regulations of Indian Explosives Act. and cross-wise so as to tie the stacks together
and minimize the danger of toppling over.
3.4.2 Materials which are likely to be affected by
Cement bags shall be stacked in a manner to
subsidence of soil like precast beams, slabs and timber
facilitate their removal and use in the order
of sizes shall be stored by adopting suitable measures
in which they are received; a table showing
to ensure unyielding supports.
date of receipt of cement shall be put on each
3.4.3 Materials liable to be affected by floods, tides, stack to know the age of cement.
etc shall be suitably stored to prevent their being For extra safety during monsoon, or when it
washed away or damaged due to floods, tides, etc. is expected to store for an unusually long
period, the stack shall be completely enclosed
4 STORAGE, STACKING AND HANDLING OF by a water proofing membrane such as
MATERIALS polyethylene, which shall close on the top of
4.1 The storage stacking and handling of materials the stack. Care shall be taken to see that the
generally used in construction shall be as given in 4.2 waterproofing membrane is not damaged any
to 4.31, which have been summarized in the form of a time during the use.
check list in Annex B. Exposure to asbestos fibres/ Cement in gunny bags, paper bags and
dust is known to be harmful to health of human beings. polyethylene bags shall be stored separately.
Prescribed guidelines in accordance with good practice In case cement is received in drums, these

12 NATIONAL BUILDING CODE OF INDIA


—. ,,. .m..— . ..—1. .—..—.—.,.— -— .. . . . . .. . . . .. . . . . . . . . . . . -. -- ..-..— . . . ..—

‘A.C. OR G.1. SHEET


OR ANY KIND OF
WEATHER PROOF
ROOF

LOAD BEARING

mm
> WALL
2.4’onl
r
1.40m*
B
11
GL
I D

u L *
* 10 BAGS MAXIMUM
SECTION XX
b

T x
A

G x

1.40m .6rn 1.40m .6m


~i -1

DOOR

PLAN

A = Planks
B = Wooden Battens
c = 150 Dry Bricks in Two Layer or Lean Cement Concrete
D = 150 Consolidated Earth

Fig. 2 Typical Arrangement in Cement Godown

shall be stored on plane level ground, as far plan. Proper access shall be provided for the
as possible near the concrete mixing place. replacement of silos.
After taking out the required quantity of Different types of cements shall be stacked
cement, the lid of the drum shall be securely and stored separately.
tied to prevent ingress of moisture. b) Handling — Hooks shall not be used for
In case cement is received in silos, the silos handling cement bags unless specifically
shall be placed near the concrete batching permitted by the engineer-in-charge.

FART 7’ CONSTRUCTIONAL PRACTICES AND SAFETY 13


For information regarding bulk handling of shall be shutdown and locked out electrically as weli
cement, see 4.4. as mechanically. When necessary for a workman to
enter such storage area, he shall wear a life-line, with
4.3 Lime
another workman outside the silo or hopper attending
4.3.1 Quicklime Before Slaking the rope.

a) Storage and stacking — Quicklime should be 4.5 Masonry Units


slaked as soon as possible. If unavoidable it
a) Stones — Stones of different sizes, types and
may be stored in compact heaps having only
classification shall be stored separately.
the minimum of exposed area. The heaps shall
be stored on a suitable platform and covered Stones shall be stacked on dry fm ground in
to avoid direct contact with rain or being a [email protected] heap not more than 1 m in height.
blown away by wind. In case quick lime is ,,:@-
,.,K. ,
stones shall be stacked against
-

stored in a covered shed, a minimum space &@k&aupport on a firm dry ground in tiers,
of 300 mm should be provided alround the up to a height of 1.2 m. A distance of about
0.8 m shall be kept between two adjacent
heaps to avoid bulging of wrdls.
stacks.
Unslaked lime shall be stored in a place
inaccessible to water and because of fire b) Bricks — Bricks shall be stacked in regular
hazards, shall be segregated from the tiers as and when they are unloaded to
combustible materials. minimize breakage and defacement. These
shall not be dumped at site. In the case of
b) Handling — See 4.4.
bricks madi from clays containing lime
4.3.2 Hydrated Lime KANKAR, the bricks in stack should be
thoroughly soaked in water (docked) to
a) Storage and stacking — Hydrated lime is
prevent lime bursting.
generally supplied in containers, such as jute
Bricks shall be stacked on dry firm ground.
bags lined with polyethylene or craft paper
For proper inspection of quality and east in
bags. It should be stored in a building to
protect the lime from dampness and to counting, the stacks shall be 50 bricks long,
10 bricks high and not more than 4 bricks in
minimize warehouse deterioration.
width, the bricks being placed on edge, two
The building should be with a concrete floor
at a time along the width of the stack. Clear
and having least ventilation to eliminate
distance between adjacent stacks shall not be
draughts through the walls and roof. In
less than 0.8 m. Bricks of each truckload shall
general, the recommendations given in 4.2 for
be put in one stack. Bricks of different types,
storing of cement shall be applicable for
such as, clay bricks, clay fly ash bricks, fly
hydrated lime. When air movement is reduced
ash lime bricks, sand lime (calcium silicate)
to a practical minimum, hydrated lime can be
bricks shall be stacked separately. Bricks of
stored for up to three months without
different classifications from strength
appreciable change.
consideration and size consideration (such as,
b) Handling — See 4.4. conventional and modular) shall be stacked
4.3.3 Dry Slaked Lime separately. Also bricks of different types, such
as, solid, hollow and perforated shall be
a) Storage and stacking — The lime shall be stacked separately.
stored in a dry and closed godown.
c) Blocks — Blocks are available as hollow and
b) Handling — See 4.4. solid concrete blocks, hollow and solid light
4.4 Handling of Cement and Lime weight concrete blocks, autoclave aerated
concrete blocks, concrete stone masonry
Workmen, handling bulk cement or lime shall wear
blocks and soil based blocks. Blocks shall be
protective clothing, respirators, and goggles; shall be
unloaded one at a time and stacked in regular
instructed in the need of cleanliness to prevent
tiers to minimize breakage and defacement.
dermatitis, and shall be provided with hand cream,
These shall not be dumped at site. The height
petroleum jelly, or similar preparation for protection
of the stack shall not be more than 1.2 m, the
of exposed skin.
length of the stack shall not be more than
Bulk cement stored in silos or bins may fail to feed 3.0 m, as far as possible and the width shall
to the ejection system. When necessary to enter a silo be of two or three blocks. Normally blocks
or bin for any purpose, the ejection system employed cured for 28 days only should be received at

14 NATIONAL BUILDING CODE OF INDIA’


site. In case blocks cured for less than 28 days removed from each other to prevent the
are received, these shall be stacked separately. material at the edges of the piles from getting
All blocks should be water cured for 10 to 14 intermixed. On a large job it is desirable to
days and air cured for another 15 days; thus construct dividing walls to give each type of
no blocks with less than 28 days curing shall aggregates its own compartment. Fine
be used in building construction. Blocks shall aggregates shall be stacked in a place where
be placed close to the site of work so that least loss due to the effect of wind is minimum.
effort is required for their transportation. The b) Handling — When withdrawals are made
date of manufacture of the blocks shall be from stock piles, no over hang shall be
suitably marked on the stacks of blocks permitted.
manufactured at factory or site. Employees required to enter hoppers shall be
d) Handling — Brick stacks shall be placed close equipped with safety belts and life-lines,
to the site of work so that least effort is attended by another person. Machine driven
required to unload and transport the bricks hoppers, feeders, and loaders shall be locked
again by loading on pallets or in barrows. in the off position prior to entry electrically
Unloading of building bricks or handling in as well as mechanically.
any other way likely to damage the corners
or edges or other parts of bricks shall not be 4.8 Pulverized Fuel Ash/Fly Ash
permitted.
a) Storage and Stacking — Fly ash shall be
4.6 Floors, Wall and Roof Tiles stored in such a manner as to permit easy
access for proper inspection and identification
a) Storage and Stacking — Floor, wall and clay of each consignment. Fly ash in bulk
roof tiles of different types, such as, cement quantities shall be stored in stack similar to
concrete tiles (plain, coloured and terrazzo) and fine aggregates, avoiding any intrusion of
ceramic tiles (glazed and unglazed) shall be foreign matter. Fly ash in bags shall be stored
stacked on regular platform as far as possible in stacks not more than 10 bags high.
under cover in proper layers and in tiers and b) Handling — See 4.4.
they shall not be dumped in heaps. In the stack,
the tiles shall be so placed that the mould 4.9 Cinder
surface of one faces that of another. Height of
Cinder shall be stored in bulk quantities in stacks
the stack shall not more than 1 m.
similar to coarse aggregates avoiding any extrusion of
Tiles of different quality, size and thickness
foreign matter.
shall be stacked separately to facilitate easy
removal for use in work. Tiles when supplied 4.10 Timber
by manufacturers packed in wooden crates
shall be stored in crates. The crates shall be a) Storage and Stacking — Timber shall be
opened one at a time as and when required stored in stacks upon well treated and even
for use. surfaced beams, sleepers or brick pillars so
as to be above the ground level by at least
b) Handling — Ceramic tiles and roof tiles are
150 mm to ensure that the timber will not be
generally supplied in cartons which shall be
affected by accumulation of water under it.
handled with care to avoid breakage. It is
Various members shall preferably be stored
preferable to transport these at the site on
separately in different lengths, and material
platform trolleys.
of equal lengths shall be piles together in
4.7 Aggregate layers with wooden battens, called crossers,
separating one layer from another. The
a) Storage and Stacking — Aggregates shall be crossers shall be of sound wood, straight and
stored at site on a hard dry and level patch of uniform in thickness. In case, where separate
ground. If such a surface is not available, a crossers are not available smaller sections of
platform of planks or old corrugated iron the available structural timber may be
sheets, or a floor of bricks, or a thin layer of employed in their place. In any layer an air
lean concrete shall be made so as to prevent space of about 25 mm shall be provided
the mixing with clay, dust, vegetable and other between adjacent members. The longer pieces
foreign matter. shall be placed in the bottom layers and
Stacks of fine and coarse aggregate shall be shorter pieces in the top layers but one end of
kept in separate stock piles sufficiently the stack shall be in true vertical alignment.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 15


The crossers in different layers shall be in 4.12 Partially Prefabricated Wall and Roof
vertical alignment. The most suitable width Components
and height of a stack are recommended to be
a) Storage and Stacking — The wall components
about 1.5 m and 2.0 m. Distance between
comprise blocks, sills, lintels, etc. The blocks
adjacent stacks is recommended to be at least
shall be stacked in accordance with 4.5(c).
450 mm. In case the stacking with the help of
These shall be stacked on plane level ground
battens is not possible, the timber may be
having a floor of bricks or a thin layer of lean
close piled in heaps on raised foundations with
concrete.
the precautions specified above.
The roof components such as precast RC
The stacks shall be protected from hot dry
joists, prefabricated brick panels, RC planks,
winds or direct sun and rain. Heavy weights,
channel units, cored units, waffle units,
such as metal rails or large sections of wood,
L-panel, single tee and double tee sections,
are recommended to be placed on the top of
ferrocement panels, etc shall be unloaded as
the stack to prevent distortion or warping of
individual components. These shall be
the timber in the stack. In case timber is to be
stacked on plane level ground having a floor
stored for about a year or more, to prevent
of bricks or a thin layer of lean concrete. RC
end-cracking in the material, the ends of all
planks, prefabricated brick panels and
members shall be coated with coal tar,
ferrocement panels shall be stacked against a
aluminium leaf paints (hardened gloss oil),
brick masonry wall in slightly inclined
microcrystalline wax or any other suitable
position on both sides of the wall. Channel
material.
units, cored units and L-panels shall be , .
b) Care must be taken that handler or workmen
stacked one over the other up to five tiers.
are not injured by rails, straps, etc, attached
The waffle units shall be stacked upside down
to the used timber. This applies particularly
as individual units. The RC joists, single tee
to planks and formwork for shuttenng.
and double tee sections shall be stacked as
individual units one adj scent to the other. The
4.11 Bamboo
distance between any two adjacent stacks
4.11.1 The site shall be properly inspected and termite shall not be less than 450 mm.
colonies or mounds if detected shall be destroyed. b) Handling — The components shall be
All refuse and useless cellulosic materials shall be handled by holding the individual component
removed from the site. The ground may then be by holding a specified points so that the
disinfected by suitable insecticides. The area should stresses due to handling are minimized.
have good drainage.
4.13 Steel
4.11.2 Bamboo may preferably be stacked on high
a) Storage and Stacking — For each classification
skids or raised platform atleast 300 mm above ground,
of steel, separate areas shall be earmarked. It
Storage under cover reduces the liability to fungal
is desirable that ends of bars and sections of
attack. Good ventilation and frequent inspection are
each class be painted in distinct separate
important.
colours. Steel reinforcement shall be stored
4.11.3 Bamboo dries by air-seasoning under cover in in a way as to prevent distortion and corrosion.
the storage yards from 6 to 12 weeks time. It is desirable to coat reinforcement with
cement wash before stacking to prevent
4.11.4 Prophylactic treatment of bamboo during
scaling and rusting.
storage prevents losses due to fungi and insects even
under open storage. Following chemicals are found Bars of differen~ classification, sizes and
suitable at the coverage rate of 24 litres per tonne. lengths shall be stored separately to facilitate
issues in such sizes and lengths as to minimize ,-
Sodium pentachlorophenate :1 percent solution wastage in cut from standard lengths.
Boric acid + borax (1:1) :2 percent solution In case of long storage or in coastal areas,
Sodium pentachlorophenate reinforcement bars shall be stacked above
+ boric acid + borax (5:1:1) :2.5 percent solution ground level by at least 150 mm and a coat of
A mixture of these compounds yields the best results. cement wash shall be given to prevent scaling
and rusting.
NOTE— For better protectionof structuralbamboo(if stored
outside),repetitionof the treatmentafter four to six monthsis Structural steel of different sections, sizes and
desirable. lengths shall be stored separately. It shall be

16 NATIONAL BUILDING CODE OF INDIA


stored above ground level by at least 150 mm straight. These cross battens should be of
upon platforms, skids or any other suitable uniform thickness and placed vertically one
supports to avoid distortion of sections. In above the other. The door shutters shall be
case of coastal areas or in case of long storage, stacked in the form of clean vertical stacks
suitable protective coating of cement wash one over the other and at least 80 mm above
shall be given to prevent scaling and rusting. ground on pallets or suitable beams or rafters.
b) Handling — Tag lines shall be used to control The top of the stack shall be covered by a
the load in handling reinforcements or protecting cover and weighted down by
structural steel when a crane is employed. means of scantlings or other suitable weights.
Heavy steel sections and bundles shall be The shutter stack shall rest on hard and level
lifted and carried with the help of slings and surface.
tackles and shall not be carried on the If any timber or other lignocellulosic material
shoulders of the workmen. based frame or shutter becomes wet during
transit, it shall be kept separate from the
4.14 Aluminium Sections
undamaged material. The wet material may
a) Storage and Stacking — Aluminium sections be dried by stacking in shade with battens in
of different classification, sizes and lengths between adjacent boards with free access of
shall be stored separately, on a level platform dry air. Separate stacks shall be built up for
under cover. each size, each grade an each type of material.
b) Handling — The aluminium sections shall not When materials of different sizes, grades and
be pulled or pushed from the stack nor shall types are to be stacked in one stack due to
be slided over each other, to protect the shortage of space, the bigger size shall be
anodizing layer. stacked in the lower portion of the stacks.
Suitable pallets or separating battens shall be
4.15 D oors, Windows and Ventilators kept in between the two types of material.
a) Storage and Stacking — Metal and plastic Precast concrete door and window frames
doors, windows and ventilators shall be shall be stored in upright position adopting
stacked upright (on their sills) on level ground suitable measures against risk of subsidence
preferably on wooden battens and shall not of soillsupport.
come in contact with dirt or ashes. If received b) Handling — While unloading, shifting,
in crates they shall be stacked according to handling and stacking timber or other
manufacturer’s instructions and removed lignocellulosic material based, metal and
from the crates as and when required for the plastic door and window frames and shutters,
work. care shall be taken that the pieces are not
Metal and plastic frames of doors, windows dragged one over the other as it may cause
and ventilators shall be stacked upside down damage to their surface particularly in case
with the kick plates at the top. These shall of the decorative shutters. The pieces should
not be allowed to stand for long in this manner be lifted and carried preferably flat avoiding
before being fixed so as to avoid the door damage to corners or sides.
frames getting out of shape and hinges being
4.16 Rooting Materials
strained and shutters drooping.
During the period of storage of aluminium 4.16.1 Roofing sheets shall be stored and stacked in
doors, windows and ventilators, these shall such a manner as not to damage them in any way.
be protected form loose cement and mortar Damaged sheets shall ndt be stacked with sound
by suitable covering, such as tarpaulin. The materials. All damaged sheets shall be salvaged as early
tarpaulin shall be hung loosely on temporary as possible.
framing to permit circulation of air to prevent
4.16.2 Asbestos Cement Sheet
moisture condensation.
All timber and other lignocellulosic material a) Storage and stackings — Asbestos cement
based frames and shutters shall be stored in a sheets shall be stacked to a height of not more
dry and clean covered space away from any than one metre on firm and level ground, with
infestation and dampness. The storage shall timber or other packing beneath them. If
preferably be in well-ventilated dry rooms. stacked in exposed position, they shall be
The frames shall be stacked one over the other protected from damage by the winds.
distances to keep the stack vertical and b) Handling — Not more than two sheets shall

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 17


be first pushed forward along the valley line 4.18 Plastic and Rubber Flooring Sheets and Tiles
say about one fourth of the sheet length and
a) Storage and Stacking — Plastic and rubber
preferably carried by two workmen. Asbestos
sheets have tendency to break-down during
cement sheets shall be lowered or raised
storage. Plastic and rubber sheets shall
gently and not thrown.
be stored according to manufacturer’s
4.16.3 CGI Sheets instructions.

a) Storage and sracking — CGI sheets shall be The coolest store room available shall be
stacked in not more than 100 bundles per utilized for the storage of the sheets. The store
stack built solidly, each bundle consisting of rooms where the sheets are stored shall be well
10 sheets. Bundles shall be so laid that the ventilated and direct light should not be
corrugations run in the same directions in allowed to fall on them.
every course. One end of the stack shall be The sheets shall be stored away from electric
raised by 100 mm to 150 mm to allow water generators, electric motors, switchgears and
flowing freely. If the sheets are not to be used other such electrical equipment as they
immediately, these shall be stacked under roof produce harmful gases as they produce
cover. harmful order in their vicinity.
b) Handling — In bulk handling of CGI sheets, Contamination of the sheets with vegetable
workmen shall be provided with suitable hand and mineral oils; greases; organic solvents;
protection. acids and their fumes; alkalies; dust and
grit shall be prevented. Where greasy
4.17 Boards contamination occurs this shall be removed
4.17.1 Gypsurn Boards immediately with petrol and the sheets and
tiles thoroughly wiped dry and dusted with
a) Storage and stacking — Gypsum boards shall
chalk chalk.
be stored flat in a covered clean and dry place.
Undue stretch and strain, kinks, sharp bends
b) Handling — See 4.11.2(b).
or folds of the sheets and tiles shall be
4.17.2 Plywood, Fibre Board, Particle Board, Block avoided. In case of long storage, the sheets
Board, etc shall be turned over periodically and treated
with chalk powder, if necessary.
a) Storage and Stacking — Plywood, fibre board,
particle board, block board, etc, shall not be b) Handling — While handling plastic and
rubber sheets, workmen shall lift the sheets
stored in the open and exposed to direct sun
and carry them flat to avoid sharp bends or
and rain. The boards shall be stacked on a flat
folds of the sheets.
dunnage, on the top of which a wooden
frame shall be constructed with battens of 4.19 Glass Sheets
50 mm x 25 mm (Min) in such a way that it
a) Storage and Stacking — It is important that
supports all four edges and comers of the
all glass sheets whether stored in crates or not
boards with intermediate battens placed at
shall be kept dry. Suitable covered storage
suitable intervals to avoid warping. If required,
space shall be provided for the safe storage
the stack shall be adequately raised above
of the glass sheets. The glass sheets shall be
ground level to ensure that it will not be
lifted and stored on their long edges and shall
affected by accumulation of water under it.
be put into stacks of not more than 25 panes,
The board shall be stacked in a solid block in supported at two points by fillets of wood at
a clear vertical alignment. The top sheet of about 300 mm from each end. The first pane
each stack shall be suitably weighed down to laid in each stack shall be so placed that its
prevent warping, wherever necessary. bottom edge is about 25 mm from the base of
b) Handling — The board shall be unloaded and the wall or other support against which the
stacked with utmost care avoiding damage to stack rests. The whole stack shall be as close
the comers and surface. In case of decorative and as upright as possible. To prevent slipping
plywood and decorative boards, the surfaces on smooth floor, the floor shall be covered
of which are likely to get damaged by with gunny bags. The glass sheets of different
dragging one sheet over another, it is sizes, thickness and type shall be stacked
advisable that these are lifted as far as possible separately. The distance between any two
in pairs facing each other. stacks shall be of the order of 400 mm.

,
18 NATIONAL BUILDING CODE OF INDIA
b) Handling — Workmen handling glass panes, b) Handling — Removal of pipe from a pile shall
waste glass pieces and fibre glass shall be be accomplished by working from the ends
provided with suitable hand protection. In of the pipe.
removing glass sheets from crates, due care
4.22 Unplasticized PVC Pipes
shall be taken to avoid damages. Glass edges
shall be covered or otherwise protected to a) Storage and Stacking — Pipes should be
prevent injuries to workmen. stored on a reasonably flat surface free from
stones and sharp projections so that the pipe
4.20 Cast Iron, Galvanized Iron and Asbestos is supported throughout its length. The pipe
Cement Pipes and Fittings should be given adequate support at all times.
a) Storage and Stacking — The pipes shall be In storage, pipe racks should be avoided. Pipe
unloaded where they are required, when the should not be stacked in large piles especially
trenches are ready to receive them. under warm temperature conditions as the
bottom pipes may distort thus giving rise to
Storage shall be provided at the bottom layer
difficulty in jointing. Socket and spigot pipes
to keep the stack stable. The stack shall be in
should be stacked in layers with sockets
pyramid shape or the pipes placed length-wise
placed at alternate ends or the stacks to avoid
and cross-wise in alternate layers. The
lopsided stacks.
pyramid stack is advisable in smaller diameter
pipes for conserving space in storing them. It is recommended not to store a pipe inside
The height of the stack shall not exceed 1.5 m. another pipe. On no account should pipes be
Each stack shall contain only pipes of the stored in a stressed or bend condition or near
same class and size. a source of heat. Pipes should not be stacked
more than 1.5 m high. Pipes of different sizes
Each stack shall contain only pipes of same
and classes should be stacked separately.
class and size, with consignment or batch
number marked on it with particulars or In tropical conditions, pipes should be stored
suppliers wherever possible. in shade. In very cold weather, the impact
strength of PVC is reduced making it brittle.
Cast iron detachable joints and fittings shall
be stacked under cover and separated from The ends of pipe should be protected from
the asbestos cement pipes and fittings. abrasion particularly those specially prepared
for jointing either spigot or socket solvent
Rubber rings shall be kept clean, away from
welded joints or soldered for use with
grease, oil, heat and light.
couplings.
b) Handling — Pipes in the top layer shall be
If due to unsatisfactory storage or handling a
handled first. At a time only one pipe shall be
pipe become brittle in very cold weather.
handled by two labourers while conveying
to the actual site and shall be carried b) Handling — Great care shall be exercised in
on shoulders. Fittings shall be handled handling these pipes in wintry conditions as
individually. these come brittle in very cold weather.

4.23 Pipes of Conducting Materials


4.21 Polyethylene Pipes
a) Storage and Stacking — Pipes shall be
a) Storage and Stacking — Black polyethylene
stacked on soliddevel sills and contained in a
pipes may be stored either under cover or in
manner to prevent spreading or rolling of the
the open. Natural polyethylene pipes,
pipe. Where quantity storage is necessary,
however, should be stored under cover and
suitable packin~ shall be placed between
protected from direct sunlight.
succeeding layers to reduce the pressure and
Coils may be stored either on edge or stacked resulting spreading of the pile.
flat one on top of the other, but in either case In stacking and handling of pipes and other
they should not be allowed to come into conducting materials, the following minimum
contact with hot water or steam pipes and safety distances shall be ensured from the
should be kept away from hot surface.
overhead power lines:
Straight lengths should be stored on horizontal 11 kV and below 1.40 m
racks giving continuous support to prevent the Above 11 and below 33 kV 3.60 m
pipe taking on a permanent set. Above 33 and below 132 kV 4.70 m
Storage of pipes in heated areas exceeding Above 132 and below 275 kV 5.70 m
27°C should be avoided. Above 275 and below 400 kV 6.50 m

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 19


b) Handling — Removal of pipes from a pile exposed heating elements, shall not be
shall be accomplished by working from the permitted in area or rooms where spray
ends of the pipe. During transportation, the painting is done nor shrdl smoking be allowed
pipes shall be so secured as to insure against there.
displacement. Care should be taken not to use any naked
flame inside the paint store. Buckets
4.24 Piles and Poles
containing sand shall be kept ready for use in
a) Storage and Stacking — Piles and poles shall case of fire. Fire extinguishers when required
be carefully stacked on solid, level sills so as shall be of foam type conforming to accepted
to prevent rolling or spreading of the pile. standards [7(4)].
The storage area shall be maintained free of Each workman handling lead based paints
vegetation and flammable materials. shall be issued Y2litre milk per day for his
b) Handling — When placing piles or poles on personal consumption.
the stack, workmen shall work from the ends
4.26 Bitumen, Road Tar, Asphalt, Etc
of the piles/poles. Similar precautions shall
be observed in removal of piles/poles from a) Storage and Stacking — Drums or containers
the stack. Tag lines shall be used to control containing all types of bitumen, road tar,
piles and poles when handling for any asphalt, etc, shall be stacked vertically on their
purpose. bottoms in up to three tiers. Leaky drums shall
In stacking and handling of piles and poles, be segregated. Empty drums shall be stored
...
precautions as laid down in 4.18(a) shall be in pyra midal stacks neatly in rows.
followed. b) Handling — See 19.3.1.2 and 19.3.4.

4.25 Paints, Varnishes and Thinners 4.27 Bituminous Roofing Felts

a) Storage and Stacking — Paints, varnishes, a) Storage and Stacking — Bituminous roofing
lacquers, thinners and other flammable felts shall be stored away from other
materials shall be kept in properly sealed or combustible materials and shall be kept under
closed containers. The containers shall be kept shade.
in a well ventilated location, free from b) Handling — Bituminous roofing felts should
excessive heat, smoke, sparks or flame. The be handled in a manner to prevent cracking
floor of the paint stores shall be made up of and other damages.
100 mm thick loose sand. ...
Paint materials in quantities other than 4.28 Flammable Materials k
required for daily use shall be kept stocked a) Storage and Stacking — In addition to the
under regular storage place. requirements as laid down in 3.4, the
Where the paint is likely to deteriorate with following provisions shall also apply:
age, the manner of storage shall facilitate 1) Outdoor storage of drums requires some
removal and use of lots in the same order in care to avoid contamination because
which they are received. moisture and dirt in hydraulic brake and
Temporary electrical wirings/fittings shall not transmission fluid, gasoline, or lubricants
be installed in the paint store. when electric may cause malfunction or failure of
lights, switches or electrical equipment are equipment, with possible danger to
necessary, they shall be of explosion proof personnel. The storage area should be
design. free of accumulations of spilled products,
b) Handling — Ventilation adequate to prevent debris and other hazards.
the accumulation of flammable vapours to 2) Compressed gases and petroleum
hazardous levels of concentration shall be products shall not be stored in the same
provided in all areas where painting is done. building or close to each other. Storage
When painting is done is confined spaces of petroleum products should be as per
where flammable or explosive vapours may Petroleum Rules.
develop, any necessary heat shall be provided b) Handling — Petroleum products delivered to
through duct work remote from the source of the job site and stored there in drums shall be
flame. protected during handling to prevent loss of
Sources of ignition, such as open flame and identification through damage to drum

20 NATIONAL BUILDING CODE OF INDIA


T

markings, tags, etc. Unidentifiable petroleum 4.32.2 Heavy units like precast concrete members shall
products may result in improper use, with be stacked near the hoist or the ramp.
possible fire hazard, damage to equipment or
4.32.3 Materials which normally deteriorate during
operating failure.
storage shall be kept constantly moving, by replacing
Workmen shall be required to guard carefully old materials with fresh stocks. Freshly arrived
against any part of their clothing becoming materials shall never be placed over materials which
contaminated with flammable fluids. They had arrived earlier.
shall not be allowed to continue work when
their clothing becomes so contaminated. 4.32.4 Appropriate types of fiie extinguishers shall be
provided at open sites where combustible materials are
4.29 Water
stored and for each storage shedlroom where
Water to be stored for construction purposes shall be flammable/combustible materials are stored. For
stored in proper tanks to prevent any organic impurities. guidance regarding selection of the appropriate types
The aggregate capacity of storage tanks shall be of fire extinguishers reference may be made to good
determined after taking into account the requirements practice [7(4)]. It is desirable that a minimum of two
of fire fighting. extinguishers are provided at each such location.

4.30 Sanitary Appliances 4.32.5 Workers handling excavated earth from


foundation, particularly if the site happens to be
a) Storage and Stacking — All sanitary
reclaimed area or marshy area or any other infected
appliances shall be carefully stored under
area, shall be protected against infection affecting their
cover to prevent damage. When accepting and
exposed body portions.
storing appliances, consideration shall be
given to the sequence of removal from the 4.32.6 House Keeping
store to the assembly positions. Vitreous
fittings shall be stacked separately from the Stairways, walkways, scaffolds, and accessways shall
metal ones. be kept free of materials, debris and obstructions. The
b) Handling — Bigger sanitary appliances shall engineer-in-charge/the foreman shall initiate and carry
be handled one at a time. Traps, water seals out a programme requiring routine removal of scrap
and gullies shall be handled separately. While and debris from scaffolds and walkways.
handling sanitary fittings they shall be free 4.32.7 Where stacking of the materials is to be done
from any oil spillings, etc. The hands of the on road side berms in the street and other public place,
workers shall also be free from any oily the owner shall seek permission from the Authority
substance. Before lowering the appliances in for such stacking and also for removing the remnants
their position the supporting brackets, of the same after the construction is over, so as to avoid
pedestals, etc, shall be checked for their any hazard to the public.
soundness and then only the fixtures be
attached. 5 UNLOADING RAILIROAD WAGONS AND
MOTOR VEHICLES
4.31 Other Materials
5.1 Loading and Unloading Rail/Road Wagons
Polymeric materials such as coatings, sheetings,
reflective surfacings/sheetings, etc shall be stored as 5.1.1 Appropriate warning signals shall be displayed
per the manufacturers’ instructions. Special precautions to indicate that the wagons shall not be coupled or
shall be taken in case of storage, handling and usage moved.
of toxic materials.
5.1.2 The wheels of wagons shall always be sprigged
Small articles like screws, bolts, nuts, door and window or chained while the wagons are being unloaded. The
fittings, polishing stones, protective clothing, spare brakes alone shall not be depended upon.
parts of machinery, linings, packings, water supply and
5.1.3 Special level bars shall preferably be used for
sanitary fittings, and electrical fittings, insulation
moving rail wagons rather than ordinary crow bars.
board, etc, shall be kept in suitable and properly
protected containers or store rooms. Valuable small 5.1.4 Where gangplanks are used between wagons and
materials shall be kept under lock and key. platforms of piles (heaps), cleats at lower end of
gangplank, or pin through end of gangplanks, shall be
4.32 Special Considerations
used to prevent sliding. If gangplank is on a gradient,
4.32.1 Materials constantly in use shall be relatively cleats or abrasive surface shall be provided for the
nearer the place of use. entire length.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 21


,.

5.1.5 When raillroad wagons are being loaded or other hazards wherever specified by the Local/State
unloaded near passageways or walkways, adequate Authority or in the Acts of the Government take
warning signals shall be placed on each end of the precedence over whatever is herein specified in case
wagon to warn pedestrians. of a doubt or dispute.

5.2 Loading and Unloading from Motor Vehicles 6.3 Safety Management

5.2.1 The motor vehicles shall be properly blocked 6.3.1 The safety of personnel engaged in building
while being loaded or unloaded; brakes alone shall not construction should be ensured through a well planned
be depended upon to hold them. and well organized mechanism. For this, depending
on the size and complexity of building construction
5.2.2 When motor vehicles are being loaded or
project, safety committee shall be constituted to
unloaded near passageways or walkways, adequate
efficiently manage all safety related affairs. The site
warning signs shall be placed on each end of the vehicle
in-charge or his nominee of a senior rank shall head
to warn the pedestrians.
the committee and a safety officer shall act as member-
5.3 Handling Heavy/Long Items secretary, The meetings of the safety committee shall
be organized regularly say fortnightly or monthly
5.3.1 Loading and unloading of heavy items, shall, as depending on the nature of the project, however,
far as possible, be done with cranes or gantries. The emergency meetings shall be called as and when
workman shall stand clear of the material being moved required. The safety committees shall deal with all the
by mechanical equipment. The slings and the ropes safety related issues through well structured agenda,
used shall be of adequate load carrying capacity, so as ..
in the meetings and all safety related measures installed
not to give way and result in accidents. at the site and implementation thereof shall be
5.3.2 While heavy and long components are being periodically reviewed.
manually loaded into motor vehicle, wagons, trailer, 6.3.2 Notwithstanding the guidelines given in 6.3.1,
etc, either wooden sleepers or steel rails of sufficient all provisions given in relevant Act/Rules/Regulations
length and properly secured in position shall be put in as amended from time to time shall be followed; in
a gentle slope against the body of the wagon/vehicle this regard, reference shall also be made to the Building
at 3 or 4 places for loading. These long items shall be and Other Construction Workers Act, 1996 and the
dragged, one by one, gently and uniformly along these Rules/Regulations framed thereunder.
supports by means of ropes, being pulled by men with
feet properly anchored against firm surface. As soon 7 TERMINOLOGY
as the items come on the floor of the vehicle, the same
7.1 For the purpose of this Part the following
may be shifted by crowbars and other suitable leverage
definitions shall apply.
mechanism, but not by hands to avoid causing accident
to the workmen. 7.2 Authority Having Jurisdiction — The Authority
which has been created by a statute and which for the
5.3.3 Similar procedure as outlined in 5.3.2 shall
purpose of administering the Code/Part, may authorize
be followed for manual unloading of long or heavy
a committee or an official to act on its behalf;
items.
hereinafter called the ‘Authority’.
SECTION 3 SAFETY IN CONSTRUCTION 7.3 Construction Equipment — All equipment,
OF ELEMENTS OF A BUILDING machinery, tools and temporary retaining structures
and working platforms, that is, tools, derricks, staging,
6 GENERAL
scaffolds, runways, ladders and all material, handling
6.1 The provisions of this Section shall apply to the equipment including safety devices.
erection/alterational of the various parts of a building
7.4 Floor Hole — An opening measuring less than
or similar structure. The construction of the different
300 mm but more than 25mrn in its least dimension,
elements shall conform to 2.3.2.
in any floor, platform, pavement, or yard, through
6.2 Other Laws which materials but not persons may fall; such as, a
belt hole, pipe opening or slot opening.
Nothing herein stated shall be construed to nullify any
rules, regulations, safety standards or statutes of the 7.5 Floor Opening — An opening measuring 300 mm
local state governments or those contained in the or more in its least dimension, in any floor, platform,
various Acts of the Government of India. The specific pavement or yard through which person may fall; such
Rules, Regulations and Acts pertaining to the as hatch way, stair or ladder opening, pit or large
protection of the public or workmen from health and manhole.

22 NATIONAL BUILDING CODE OF INDIA


7.6 Guard Railing — A barrier erected along exposed b) Site-work sheds, truck-runways, trestles, foot-
edges of an open side floor opening, wall opening, bridges, etc.
ramp, platform, or catwalk or balcony, etc, to prevent
8.2 For detailed information regarding fire safety
fall of persons.
aspects in respect of construction, location, maintenance
7.7 Materials Handing Hoists — A platform, and use of temporary structures [mentioned in 8.1.l(a)]
bucket or similar enclosure exclusively meant for including PANDALS used by public for outdoor
the lifting or lowering of construction material the assembly, reference may be made to good practice
hoists being operated from a point outside the [7(5)].
conveyance.
8.3 Special permits shall be obtained for the storage
7.8 Pile Rlg — The complete pile driving equipment of the materials on side walks and highways. It shall
comprising piling frame, leader, hammer, extractor be ensured that the material dump or the storage shed
winch and power unit. Complete pile driving rig may does not create a traffic hazard, nor it shall interfere
be mounted on rafts or pontoon or rails. Pile rig may with the free flow of the pedestrian traffic. Special
also be a mobile unit mounted on trailers or trucks, or permits shall also be obtained for the use of water
a special full revolving rig for raking piles. and electricity from the public facilities. Whenever
such utilities are made use of, adequate safety
7.9 Platform — A working space for persons,
precautions regarding drainage and elimination of
elevated above the surrounding floor or ground, such
contamination and hazards from electricity shall be
as balcony or platform for the operation of machinery
taken.
and equipment.
8.4 In order to ensure safety for the adjoining property,
7.10 Scaffold — A temporary erection of timber or adequate temporary protective guards are to be
metal work used in the construction, alteration or provided. In case these protective devices project
demolition of a building, to support or to aIlow the beyond the property, the consent of the Authority and
hoisting and lowering of workmen, their tools and that of the owner of the adjoining property shall be
materials. obtained.
7.11 Toe Board — A vertical barrier erected along 9 TESTING
exposed edge of a floor opening, wall opening,
platform, catwalk or ramp to prevent fall of materials 9.1 Tests
or persons. No structure, temporay support, scaffolding or any
construction equipment during the construction or
7.12 Wall Hole — An opening in any wall or partition
demolition of any building or structure shall be loaded
having height of less than 750 mm but more than
beyond the allowable loads and working stresses as
25 mm and width unrestricted.
provided for in Part 6 ‘Structural Design’ {see also
7.13 Wall Opening — An opening in any wall or good practice [7(6)] }.
partition having both height of at least 750 mm and 9.1.1 Whenever any doubt arises about the
width of at least 450 mm. structural adequacy of a scaffolding, support or any
other construction equipment, it shall be tested to
8 TEMPORARY CONSTRUCTION, USE OF SIDE
two and a half times the superimposed dead and
WALLS AND TEMPORARY ENCROACHMENTS
imposed loads to which the material or the
8.1 Temporary Construction equipment is subjected to and the member/material
shall sustain the test load without failure if it is to
The plans and specifications of temporary
be accepted.
constructions, which are likely to interfere with
facilities or right of way provided by the Authority, 9.2 Notwithstanding the test mentioned above, if any
shall be submitted to the Authority for approval distress in any member is visible, the member shall be
showing clearly the layout, design and construction. rejected.

8.1.1 Temporary structure referred in 8.1 shall apply 10 INSPECTION AND RECTIFICATION OF
to the following types of structures: HAZARDOUS DEFECTS
a) Structures with roof or walls made of straw, 10.1 Inspection
hay, ulugrass, golpatta, hogle, darma, mat,
canvas cloth or other like materials not The Authority shall inspect the construction equipment
adopted for permanent or continuous and if during the inspection, it is revealed that unsafe/
occupancy. illegal conditions exist, the Authority shall intimate

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 23


the owner and direct him to take immediate remedial responsibility for any loss of property or life in the
measures to remove the hazard/violation. adjoining property.

10.2 Rectification In driven piles vibration is set up which may cause


damage to adjoining structures or service lines
The owner shall proceed to rectify the defect, depending on the nature of soil condition and the
hazardous condition or violation within 24 h of the construction standard of such structures and service
receipt of the notice from the Authority. The lines. Possible extent of all such damages shall be
Authority shall have full powers to rectify the unsafe ascertained in advance, and operation and mode of
condition and all expenses incurred in this connection
driving shall be planned with appropriate measures to
is payable by the owner of the property. Illegal
ensure safety.
encroachments and non-payment of money due, in
respect of the rectification of unsafe conditions may Where in the vicinity of a site where bored or driven
vest a lien on the property with the Authority (see piling works are to be carried out there are old
also Part 2 ‘Administration’). structures which are likely to be damaged, tell-tales
shall be fixed on such structures to watch their
10.3 When the strength and adequacy of any scaffold
behaviour and timely precautions taken against any
or other construction equipment is in doubt or when
undesirable effect.
any complaint is made, the Authority shall get the same
inspected before use. 11.3 During construction, inspection shall be made by
the engineer-in-charge to ensure that all protective
11 FOUNDATIONS works carried out to safe-guard the adjoining property
11.1 General are sufficient and in good order to ensure safety (see
Part 2 ‘Administration’).
The distribution of the supporting foundation shall be
such as to avoid any harmful differential settlement of 11.4 Before carrying out any excavation work/pile
the structure. The type and design of the foundation driving, the position, depth and size of underground
adopted shall ensure safety to workmen during structures, such as water pipes, mains, cables or other
construction and residents of the neighboring services in the vicinity to the proposed work, may be
property. Sufficient care shall be taken in areas, where obtained from the Authority to prevent accidents to
withdrawal of ground water from surrounding areas workmen engaged in excavation work and calamities
could result in damages to such foundations. During for the general public.
the construction of the foundation, it shall be ensured
Prior to commencement of excavation detailed data of
that the adjoining properties are not affected by any
the type of soils that are likely to be met with during
harmful effects.
excavation shall be obtained and the type of protective
11.2 Adjoining Properties works by way of shoring timbering, etc, shall be
decided upon for the various strata that are likely to
The person causing excavation shall, before starting be encountered during excavation. For detailed
the work, give adequate notices in writing to the information regarding safety requirements during
owner of the adjoining properties, safety of which is excavation reference may be made to good practice
likely to be affected due to excavation. After having [7(7)].
given such notices, wherein details regarding the type
of protective works that are anticipated to be 12 GENERAL REQUIREMENTS AND COMMON
incorporated in the excavation are shown, written HAZARDS DURING EXCAVATION
permission shall be obtained for such excavation from
12.1 Location of Machinery and Tools
the adjoining property owners. Where necessary, the
person causing excavation shall make adequate Excavating machinery consisting of both heavy and
provision to protect the safety of adjacent property. light types shall be kept back from the excavation
If on giving such notices and the precautionary site at a distance which would be safe for such type
measures having been approved by the Authority, the of equipment. Heavy equipment, such as excavating
adjoining property owner still refuses to give machinery and road traffic shall be kept back from
necessary facilities to the person causing excavation the excavated sites at a distance of not less than the
for protecting/providing both temporary and depth of trench or at least 6 m for trench deeper than
permanent supports to such property, the 6 m. Care shall also be taken to keep excavating tools
responsibility for any damage to the adjoining and materials far away from the edge of trench to
property shall be that of the adjoining property owner. prevent such items being inadvertently knocked into
The person causing excavation shall be absolved of the trench.

24 NATIONAL BUILDING CODE OF INDIA


12.2 Excavated Materials be inspected by the local health authorities prior to
commencement of the work.
Excavated materials shall be kept back from the edges
of the trench to provide clear berm of safe width. Where 12.7 Safety of Materials
this is not feasible, the protective works designed for
Materials required for excavation, like ropes, planks
the trenches shall take into consideration, the additional
for gangways and walkways, ladders, etc, shall be
load due to overburden of materials.
inspected by the engineer-in-charge who shall ensure
12.2.1 Other Surcharges that no accident shall occur due to the failure of such
materials (see Part 5 ‘Building Materials’).
Proximity of buildings, piles of lumber, crushed rocks,
sand and other constructional materials, large trees, 12.8 Fencing and Warning Signals
etc, may impose surcharges on the side of the trench Where excavation is going on, for the safety of public
to cause sliding, etc. Under these conditions additional and the workmen, fencing shall be erected, if there is
protective works shall be provided to support the sides likelihood of the public including cattle frequenting
of the trench. the area. Sufficient number of notice boards and danger
sign lights shall be provided in the area to avoid any
12.3 Type of Strata member of public from inadvertently falling into the
Adequate precautions, depending upon the type of excavation. When excavations are being done on roads,
strata met with during excavation (like quick sand, diversion of the roads shall be provided with adequate
loose fills and loose boulder) shall be taken to protect notice board and lights indicating the diversion well
the workmen during excavation. Effect of climatic ahead. Where necessary, recourse may be had
variations and moisture content variations on the for additional precautionary measures by way of
materials under excavation shall be constantly watched watchmen to prevent accident to the general public,
and precautions taken, where necessary, immediately especially during hours of darkness.
to prevent accidents at work site.
12.9 Effect of Freezing and Thawing
12.4 Overhang and Slopes Due to expansion of water when freezing, rock
fragments, boulders, etc, are frequently loosened.
During any excavation, sufficient slopes to excavated
Therefore, the side walls of the excavation shall be
sides by way of provision of steps or gradual slopes
constantly watched for signs of cracks during a thaw.
shall be provided to ensure the safety of men and
When depending in whole or in part on freezing to
machine working in the area.
support the side walls, great care shall be taken during
12.5 Blasting for foundation of building is prohibited thaws to provide suitable bracing or remedy the
unless special permission is obtained from the condition by scaling of the loose material from the
Authority. Where blasting technique has to be resorted sides.
to, prior inspection for the stability of slopes shall be
12.10 Vibrations from Nearby Sources
carried out. After blasting, overhangs or loose boulders
shall be cleared b y expert workers carrying out blasting Vibration due to adjacent machinery, vehicles, rail-
prior to continuation of the excavation by normal roads, blasting, piling and other sources require
working parties. additional precautions to be taken.

12.5.1 Burrowing or mining or what is known as 12.11 Precautions While Using Petroleum Powered
‘gophering’ shall not be allowed. In any trench where Equipment
such methods have been followed, the cavities felt shall At the site of excavation, where petroleum powered
be eliminated by cutting back the bare slope before equipment is used, petroleuth vapours are likely to
removing any further material from the section of the accumulate at lower levels and may cause fire
trench. explosion under favorable circumstances. Care
should, therefore, be taken to avoid all sources of
12.6 Health Hazards
ignition in such places.
Where gases or fumes are likely to be present in
trenches, sufficient mechanical ventilation, to protect 13 PILING AND OTHER DEEP FOUNDATIONS
the health and safety of persons working there, shall 13.1 General
be provided. If necessary, the persomel working there,
13.1.1 Safety Programme
shall be provided with respiratory protective equipment
when work in such unhealthy conditions has to be All operations shall be carried out under the immediate
carried out. The precautionary measures provided shall charge of a properly qualified and competent foreman

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 25


who shall also be responsible for the safety inspected pile lines and pulley blocks shall be inspected
arrangements of the work. by the foreman before the beginning of each shift, for
any excess wear or any other defect.
13.1.2 For work during night, lighting of at least 100
lux intensity shall be provided at the work site. 13.2.6.1 Defective parts of pile drivers, such as
sheaves, mechanism slings and hose shall be repaired
13.1.3 Every crane driver or hoisting appliance
by only competent person and duly inspected by
operator shall be competent tothe satisfaction of the
foreman-in-charge of the rig and the results recorded
engineer-in-charge and no person under the age of21
in the register. No steam or air equipment shall be
years should be in-charge of any hoisting machine
repaired while it is in operation or under pressure.
including any scaffolding winch, or give signals to
Hoisting ropes on pile drivers shall be made of
operator.
galvanized steel.
13.1.4 Working in compressed air, in case of deep
foundations, requires several precautions to be 13.2.7 Steam and air lines shall be controlled by easily
observed to safeguard the workmen against severe accessible shut-off valves. These lines shall consist of
hazards to life, compressed air disease and related armoured hose or its equivalent. The hose of steam
ailments. For detailed information regarding safety and air hammers shall be securely lashed to the hammer
requirements, reference may be made to good practice so as to prevent it from whipping if a connection breaks.
[7(8)]. Couplings of sections of hose shall be additionally
secured by ropes or chains.
13.2 Piling Rig
13.2.8 When not in use the hammer shall be in dropped
13.2.1 Pile drivers shall not be erected in dangerous position and shall beheld in place by a cleat, timber or
proximity to electric conductors. If two pile drivers any other suitable means.
are erected at one place these shall be separated by a
distance at least equal to the longest leg in either rig. 13.2.9 For every hoisting machine and for every
chain rig hook, shackle, swivel and pulley block used
13.2.2 The frame of any rig shall be structurally safe in hoisting or as means of suspension, the safe
for all anticipated dead, live or wind loads. Whenever working loads shall be ascertained. In case of doubt,
there is any doubt about the structural strength, suitable actual testing shall be carried out and the working
test shall be carried out by the foreman and the results load shall be taken as half of the tested load. Every
of the test recorded. No pile driving equipment shall hoisting machine and all gears referred to above shall
be taken into use until it has been inspected and found be plainly marked with the safe working load. In case
to be safe. of a hoisting machine having a variable safe working
13.2.3 Pile drivers shall be firmly supported on heavy load, each safe working load together with the
timber sills, concrete beds or other secure foundation. conditions under which it is applicable shall be clearly
If necessary, to prevent danger, pile drivers shall be indicated. No part of any m“achine or any gear shall
adequately guyed. be loaded beyond the safe working load except for
the purpose of testing.
When the rig is not in use, extra precautionaq measures
for stability, such as securing them with minimum four 13.2.10 Motor gearing, transmission, electrical wiring
guys, shall be adopted to prevent any accidents due to and other dangerous parts of hoisting appliances should
wind, storm, gales and earthquake. be provided with efficient safe guards. Hoisting
appliances shall be provided with such means as will
13.2.4 Access to working platforms and the top pulley
reduce, to the minimum, the risk of accidental descent
shall be provided by ladders. Working platforms shall
of the load and adequate precautions shall be taken to
be protected against the weather.
reduce to the minim~m, the risk of any part of
13.2.4.1 In tall driven piling rigs or rigs of similar suspended load becoming accidentally displaced.
nature where a ladder is necessary for regular use, the When workers are employed on electrical installations
ladder shail be securely fastened and extended for the which are already energized, insulating mats and
full height of the rig. wearing apparel, such as gloves, etc, as may be
necessary, shall be provided. Sheaves on pile drivers
13.2.5 Exposed gears, fly wheels, etc, shall be fully
shall be guarded so that workers may not be drawn
enclosed.
into them.
13.2.6 Pile driving equipment in use shall be inspected
13.2.10.1 When loads have to be inclined:
by a competent engineer at regular intervals not
exceeding three months. A register shall be maintained a) they shall be adequately counter-balanced,
at the site of work for recording the results of such and

26 NATIONAL BUILDING CODE OF INDIA


b) the tilting device shall be secured against 14 WALLS
slipping.
14.1 General
13.2.11 Adequate precautions shall be taken to prevent
Depending on the type of wall to be constructed the
a pile driver from overturning if a wheel breaks.
height of construction per day shall be restricted to
13.2.12 Adequate precautions shall be taken by ensure that the newly constructed wall does not come
providing stirrups or by other effective means, to down due to lack of strength in the lower layers.
prevent the rope from coming out of the top pulley or Similarly, in long walls adequate expansion/crumple
wheel. joints shall be provided to ensure safety.

13.2.13 Adequate precautions shall be taken to prevent 14.2 Scaffold


the hammer from missing the pile.
Properly designed and constructed scaffolding built by
13.2.14 If necessary, to prevent danger, long piles and competent workmen shall be provided during the
heavy sheet piling should be secured against falling. construction of the walls to ensure the safety of workers.
The scaffolding may be of timber, metal or bamboo
13.2.15 Wherever steam boilers are used, the safety
sections and the materials in scaffolding shall be
regulations of boilers shall be strictly followed and
inspected for soundness, strength, etc, at site by the
safety valves shall be adjusted to 7N/cm2 in excess of
engineer-in-charge prior to erection of scaffolds.
working pressure accurate] y.
Steel scaffolds intended for use in normal building
13.2.16 Where electricity is used as power for piling construction work shall conform to accepted standards
rig, only armoured cable conforming to the relevant [7(10)]. Bamboo and timber scaffolds shall be properly
Indian Standard shall be used. tied to the junctions with coir ropes of sufficient strength
or mechanical joints to ensure that joints do not give
13.2.17 All checks as given in the Indian Standards
way due to the load of workmen and material. Joining
and any manuals issued by the manufacturers shall be
the members of scaffolds only with nails shall be
carried out.
prohibited as they are likely to get loose under normal
13.3 Operation of Equipment weathering conditions. In the erection or maintenance
of tall buildings, scaffoldings shall be of non-
13.3.1 Workers employed in the vicinity of pile drivers combustible material especially when the work is being
shall wear helmets conforming to accepted standards done on any building in occupation. After initial
[7(9)]. construction of the scaffolding, frequent inspections of
13.3.2 Piles shall be prepared at a distance at least scaffolding. The platforms, gangways and runways
equal to twice the length of the longest pile from the provided on the scaffoldings shall be of sufficient
pile driver. strength and width to ensure safe passage for the
workmen working on the scaffolding. The joints
13.3.3 Piles being hoisted in the rig should be so slung
provided in these gangways, platforms, etc, shall be such
that they do not have to be swung round, and may not
as to ensure a fm foot-hold to the workmen. Where
inadvertently, swing or whip round. A hand rope shall
necessary, cross bars shall be provided to the full width
be fastened to a pile that is being hoisted to control its
of gangway or runway to facilitate safe walking. For
movement. While a pile is being guided into position
detailed information regarding safety requirements for
in the leads, workers shall not put their hands or arms
erection, use and dismantling of scaffolds, reference may
between the pile and the inside guide or on top of the
be made to good practice [7(1 l)].
pile, but shall use a rope for guiding.
14.2.1 The engineer-in-charge shall ensure by frequent
13.3.4 Before a good pile is hoisted into position it
inspections that gangwa~s of scaffolding have not
shall be provided with an iron ring or cap over the
become slippery due to spillage of material. Loose
driving end to prevent brooming. When creosoted
materials shall not be allowed to remain on the
wood piles are being driven, adequate precautions shall
gangways. Where necessary, because of height or
be taken, such as the provision of personal protective
restricted width, hand-rails shall be provided on both
equipment and barrier creams, to prevent workers
sides. Workers shall not be allowed to work on the
receiving eye or skin injuries from splashes of creosote.
scaffolding during bad weather and high winds.
13.3.5 When piles are driven at an inclination to the
14.2.2 In the operations involved in the erection or
vertical, if necessary, to prevent danger, these should
maintenance of outside walls, fittings, etc, of tall
rest in a guide.
buildings, it is desirable to use one or more net(s) for
13.3.6 No steam or air shall be blown down until all the safety of the workmen when the workmen are
workers are at a safe distance. required to work on scaffoldings.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 27


14.3 Ladders for workmen under ladder. For detailed information
regarding safety requirements for use of ladders,
All ladders shall be constructed of sound materials and
reference may be made to good practice [7(12)].
shall be capable of carrying their intended loads safely.
The ladders shall have not only adequate strength but 14.4 openingin walls
rigidity as well. If a ladder shows tendency to spring,
Whenever making of an opening in the existing wall
a brace shall be attached to its middle and supported
is contemplated, adequate supports against the collapse
from some other non-yielding fixed object. No ladder
or cracking of the wall portion above or roof or
having a missing or defective rung or one which
adjoining walls shall be provided.
depends for its support solely on nails, shall be used,
Ladders shall not be used as guys, braces or skids or 14.4.1 Guarding of Wall Openings and Holes
for any other purpose for which they are not intended.
Wall opening barriers and screens shall be of such
They shall not be used in horizontal position as
constriction and mounting that they are capable of
runways. They shall not be overcrowded. Wherever
withstanding the intended loads safely. For detailed
possible, ladders shall not be spliced. Where splicing
information reference may be made to good practice
is unavoidable, it shall be done only under the
[7(13)]. Every wall opening from which there is a drop
supervision of engineer-in-charge. Ladders leading to
of more than 1200 mm shrdl be guarded by one of the
landings or walkways shall extend at least one metre
following:
above the landing and shall be secured at the upper
end. To prevent slipping, a ladder shall be secured at a) Rail, roller, picket fence, half door or
the bottom end. If this cannot be done, a person shall equivalent barrier — The guard may be
be stationed at the base whenever it is in use. As a removable but should preferably be hinged
further precautions, the pitch at which a lean-to-ladder or otherwise mounted so as to be conveniently
@ used shall be such that the horizontal distance of its replaceable. Where there is danger to persons
foot from the vertical plane of its top shall be not more working or passing below on account of the
than one quarter of its length. If the surface of the floor falling materials, a removable toe board or
on which the ladder rests is smooth or sloping, the the equivalent shall also be provided. When
ladder shall be provided with non-slip bases. If the use the opening is not in use for handling
of a ladder is essential during strong winds, it shall be materials, the guards shall be kept in position
securely lashed in position. No ladder shall be placed regardless of a door on the opening. In
or leant against window pane, sashes or such other addition, a grab handle shall be provided on
unsafe or yielding objects, nor placed in front of doors each side of the opening. The opening should
opening towards it. If setup in driveways, passageways have a sill that projects above the floor level
or public walkways, it shall be protected by suitable at least 25 mm.
barricades. When ascending or descending, the user b) Extension platform into which materials may
shall face the ladder, use both his hands and place his be hoisted ~or handling, shall be of full leng~
feet near the ends of the rungs rather than near the of the opening and shall have side rails or
middle. It is dangerous to lean more than 30 cm to side equivalent guards.
in order to reach a larger area from a single setting of 14.4.2 Every chute wall opening from which there is
the ladder. Instead, the user shall get down and shift a drop of more than 1200 mm shall be guarded by
the ladder to the required position. one or more of the barriers specified in 14.4.1 or as
Metal ladders shall not be used around electrical required by the conditions.
equipment or circuits of any kind where there is a 14.5 Projection from Walls
possibility of coming in contact with the current. Metal
ladders shall be marked with signs reading ‘CAUTION: Whenever projections cantilever out of the walls,
DO NOT USE NEAR ELECTRICAL EQUIPMENT’. temporary formwork shall be provided for such
projections and the same shall not be removed till walls
Wooden ladders shall be inspected at least once in a over the projecting slabs providing stability load
month for damage and deterioration. Close visual against overturning are completely constructed.
inspection is recommended in preference to load
testing. This condition is particularly applicable to rope 15 COMMON HAZARDS DURING WALLING
and bamboo ladders wherein fraying of ropes and
15.1 Lifting of Materials for Construction
damage to bamboo is likely to occur due to materials
falling on them. When a ladder has been accidentally Implements used for camying materials to the top of
dropped it shall be inspected by the engineer-in-charge scaffoldings shall be of adequate strength and shall
prior tore-use. Overhead protection shall be provided not be overloaded during the work. Where workmen

28 NATIONAL BUILDING CODE OF INDIA


have to work below scaffoldings or ladder, overhead cater for the quantity of stores to be hoisted and
protection against the falling materials shall be prevention of overloading such hoists or buckets,
provided. Care shall be taken in carrying large bars, prevention of overturning of hoists or buckets. Where
rods, etc, during construction of the walls to prevent in a multi-storeyed building, the floor of one storey is
any damage to property or injury to workmen. to be used for storage of materials for the construction
of roofs, it shall be ensured that the quantum of stores
15.2 Haulage of Materials kept on the floor along with the load due to personnel
15.2.1 In case of precast columns, steel beams, etc, engaged in the construction work shall not exceed the
proper precautions shall be taken to correctly handle, rated capacity of the floors.
use and position them with temporary arrangement of 16.2 While roofing work is being done with corrugated
guys till grouting of the base. galvanized iron or asbestos cement sheets, it shall be
15.2.2 Manila or sisal rope shall not be used in rainy ensured that joints are kept secured in position and do
season for hoisting of heavy materials as they lose their not slip, thus causing injury to workmen. Workers
strength with alternate wetting and drying. should not be allowed to walk on asbestos cement
sheets but should be provided with walking boards.
15.3 Electical Hazards While working with tiles, it shall be ensured that they
No scaffolding, ladder, working platform, gangway are not kept loose on the roof site resulting in falling
runs, etc, shall exist within 3 m from any uninsulated of tiles on workmen in lower area. In slopes of more
electric wire. than 30° to the horizontal, the workmen shall use
ladders or other safety devices to work on the roof.
15.4 Fire Hazards
16.3 If any glass work is to be carried out in the roof,
Gangways and the ground below the scaffolding shall
it shall be ensured that injury to passerby due to
be kept free from readily combustible materials
breaking of glass is prevented. During wet conditions,
including waste and dry vegetation at all times.
the workmen shall be allowed to proceed to work on a
15.4.1 Where extensive use of blow torch or other sloping roof, only if the engineer-in-charge has
flame is anticipated scaffoldings, gangways, etc, shall satisfied himself that the workmen are not likely to
be constructed with fire resistant materials. A portable slip due to wet conditions.
dry powder extinguisher of 3 kg capacity shall be kept
16.4 Flat Roof
handy.
In any type of flat roof construction, any formwork
15.5 Mechanical Hazards
provided shall be properly designed and executed to
Care shall be taken to see that no part of scaffolding or ensure that it does not collapse during construction.
walls is struck by truck or heavy moving equipment During actual construction of roof, frequent inspection
and no materials shall be dumped against them to of the formwork shall be carried out to ensure that no
prevent any damage. When such scaffoldings are in or damage has occurred to it.
near a public thoroughfare, sufficient warning lights
16.5 While using reinforcement in roofs, it shall be
and boards shall be provided on the scaffoldings to
ensured that enough walking platforms are provided
make them clearly visible to the public.
in the reinforcement area to ensure safe walking to the
15.6 Fragile Materials concreting area. Loose wires and unprotected rod ends
shall be avoided.
During glazing operations, adequate precautions shall
be taken to ensure that the fragments of fragile 16.6 Guarding of Floor Openings and Floor Holes
materials do not cause any injury to workmen or
16.6.1 Every temporary floor opening shall have
general public in that area by way of providing
railings, or shall be constantly attended by someone.
covering to such material, side protection at work site,
Every floor hole into which persons can ,accidentally
etc.
fall shall be guarded by eithe~
16 ROOFING a) a railing with toe board on all exposed sides,
16.1 Prevention of accidental falling of workmen or
during the construction of roofs shall be ensured by b) a floor hole cover the adequate strength and
providing platforms, catch ropes, etc. If the materials it should be hinged in place. When the cover
are to be hoisted from the ground level to the roof level, is not in place, the floor hole shall be
adequate precautions shall be taken by way of correct constantly attended by some one or shall be
technique of handling, hoists of sufficient strength to protected by a removable railing.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 29


16.6.2 Every stairway floor opening shall be guarded the crane or any member being lifted shall be removed,
by a railing on all exposed sides, except at entrance to or made dead by removing the controlling fuses and
stairway. Every ladder way floor opening or platform in their absence controlling switches.
shall be guarded by a guard railing with toe board on
17.1.2.3 All practical steps shall be taken to prevent
all exposed sides (except at entrance to opening), with
the cranes being operated in dangerous proximity to a
the passage through the railing either provided with a
live overhead power line. In particular, no member of
swinging gate or so offset that a person can not walk
the crane shall be permitted to approach within the
directly into the opening.
minimum safety distances as laid down in 4.23(a).
16.6.3 Guarding of Open-Side Floors and Platjonn
If it becomes necessary to operate the cranes with
Every open-sided floor or platform 1200 mm or more clearances less than those specified above, it shall be
above adjacent floor or ground level shall be guarded ensured that the overhead power lines shall invariably
by a railing (or the equivalent) or all open sides, except be shut off during the period of operation of cranes.
where there is entrance to ramp, stair-way, or fixed Location of any underground power cables in the area
ladder. The railing shall be provided with a toe board of operation shall also be ascertained and necessary
beneath the open sides wherever: safety precautions shall be taken.

a) persons may pass; 17.1.2.4 Cranes shall not be used at a speed which
b) there is moving machinery; or causes the boom to swing.
c) there is equipment with which falling 17.1.2.5 A crane shall be thoroughly examined at least
materials could create a hazard. once in a period of 6 months by a competent person
who shall record a certificate of the check.
For detailed information, reference may be made to
good practice [7(13)]. 17.1.2.6 The operator of the crane shall follow the safe
reach of the crane as shown by the manufacturer.
17 ADDITIONAL SAFETY REQUIREMENTS
FOR ERECTION OF CONCRETE FRAMED 17.1.2.7 No person shall be lifted or transported by
STRUCTURES (HIGH-RISE BUILDINGS) the crane on its hook or boom.

17.1 Handling of Plant 17.1.2.8 Toe boards and limit stops should be provided
for wheel barrows on the loading/unloading platforms.
17.1.1 Mixers
Material should be loaded securely with no projections.
17.1.1.1 All gears, chains and rollers of mixers shall
17.1.2.9 Concrete buckets handled by crane or
be properly guarded. If the mixer has a charging skip
overhead cableway shall be suspended from deep
the operator shall ensure that the workmen are out of
throated hooks, preferably equipped with swivel and
danger before the skip is lowered. Railings shall be
safety latch. In the concrete buckets, both bottom drop
provided on the ground to prevent anyone walking
type and side drop type, closing and locking of the
under the skip while it is being lowered.
exit door of the bucket shall always be checked by the
17.1.1.2 All cables, clamps, hooks, wire ropes, gears man-in-charge of loading concrete in the bucket to
and clutches, etc, of the mixer, shall be checked and avoid accidental opening of the exit door and
cleaned, oiled and greased, and serviced once a week. consequent falling of concrete.
A trial run of the mixer shall be made and defects shall
17.1.2.10 Interlocking or other safety devices should
be removed before operating a mixer.
be installed at all stopping points of the hoists. The
17.1.1.3 When workmen are cleaning the inside of the hoists shaft way should be fenced properly.
drums, and operating power of the mixer shall be
17.1.2.11 When the buck& or other members being
locked in the off position and all fuses shall be removed
lifted are out of sight of the crane operator, a signalman
and a suitable notice hung at the place.
shall be posted in clear view of the receiving area and
17.1.2 Cranes the crane operator.

17.1.2.1 Crane rails where used shall be installed on 17.1.2.12 A standard code of hand signals shall be
firm ground and shall be properly secured. In case of adopted in controlling the movements of the crane, and
tower cranes, it shall be ensured that the level difference both the driver and the signaler shall be thoroughly
between the two rails remains within the limits familiar with the signals.
prescribed by the manufacturer to safeguard against
The driver of the crane shall respond to signals only
toppling of the crane.
from the appointed signaler but shall obey stop signal
17.1.2.2 Electrical wiring which can possibly touch at any time no matter who gives it.

30 NATIONAL BUILDING CODE OF INDIA


17.1.2.13 If a traveling gantry crane is operating over and the unit shall be level and plumb so that when
casting beds, a warning signal which sounds additional frames are installed the tower shall be in
automatically during travel should be provided to avoid level and plumb. The centering frames shall be tied
accidents to workmen crossing or standing in the path together with sufficient braces to make a rigid and solid
of the moving loads. unit. It shall be ensured that struts and diagonals braces
are in proper position and are secured so that frames
17.1.3 Trucks
develop full load carrying capacity. As erection
When trucks are being used on the site, traffic problems progresses, all connecting devices shall be in place and
shall be taken care of. A reasonably smooth traffic shall be fastened for full stability of joints and units.
surface shall be provided. If practicable, a loop road
17.2.8 In case of timber posts, vertical joints shall be
shall be provided to permit continuous operation of
properly designed. The connections shall normally be
vehicles and to eliminate their backing. If a continuous
with bolts and nuts. Use of rusted or spoiled threaded
loop is not possible, a turnout shall be provided.
bolts and nuts shall be avoided.
Backing operations shall be controlled by a signalman
positioned so as to have a clear view of the area behind 17.2.9 Unless the timber centering is supported by a
the truck and to be clearIy visible to the truck driver. manufacturer’s certificate about the loads it can stand,
Movement of workmen and plant shall be routed to centering shall be designed by a competent engineer.
avoid crossing, as much as possible, the truck lanes.
17.2.10 Centering layout shall be made by a qualified
17.1.4 Concrete Pumps (Air Compressor Operated) engineer and shall be strictly followed. The bearing
capacity of the soil shall be kept in view for every
Safety requirements in accordance with good practice
centering job. The effect of weather conditions as dry
[7( 14)] shall be followed.
clay may become very plastic after a rainfall and show
17.2 Formwork marked decrease in its bearing capacity.

17.2.1 Formwork shall be designed after taking into 17.2.11 Sills under the supports shall be set on fm
consideration spans, setting temperature of concrete, soil or other suitable material in a pattern which assures
dead load and working load to be supported and safety adequate stability for all props. Care shall be taken not
factor for the materials used for formwork {see also to disturb the soil under the supports. Adequate
good practice [7(6)] }. drainage shall be provided to drain away water coming
due to rains, washing of forms or during the curing of
17.2.2 All timber formwork shall be carefully the concrete to avoid softening of the supporting soil
inspected before use and members having cracks and starta.
excessive knots shall be discarded.
17.2.12 All centering shall be finally, inspected to
17.2.3 As timber centering usually takes an initial set
ensure that:
when vertical load is applied, the design of this
centering shall make allowance for this factor. a) footings or sills under every post of the
centering are sound.
17.2.4 The vertical supports shall be adequately braced
or otherwise secured in position that these do not fall b) all lower adjustment screws or wedges are
when the load gets released or the supports are sung against the legs of the panels.
accidently hit. c) all upper adjustment screws or heads of jacks
are in full contact with the formwork.
17.2.5 Tubular steel centering shall be used in
d) panels are plumb in both directions.
accordance with the manufacturer’s instructions. When
tubular steel and timber centering is to be used in e) all cross braces a~e in place and locking
combination necessary precautions shall be taken to devices are in closed and secure position.
avoid any unequal settlement under load. f) In case of CHHAJAS and balconies, the props
shall be adequate to transfer the load to the
17.2.6 A thorough inspection of tubular steel centering
supporting point.
is necessary before its erection and members showing
evidence of excessive resting, kinks, dents or damaged 17.2.13 During pouring of the concrete, the centering
welds shall be discarded. Buckled or broken members shall be constantly inspected and strengthened, if
shall be replaced. Care shall also be taken that locking required, wedges below the vertical supports tightened
devices are in good working order and that coupling and adjustment screws properly adjusted as necessary.
pins are effectively aligned to frames. Adequate protection of centering shall be secured from
moving vehicles or swinging loads.
17.2.7 After assembling the basic unit, adjustment
screws shall be set to their approximate final adjustment 17.2.14 Forms shall not be removed earlier than as

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 31


laid down in the specifications and until it is certain mechanical interlocks to prevent movement of the hoist
that the concrete has developed sufficient strength to in the event of a gate being opened.
support itself and all loads that will be imposed on it.
17.4.7 Winches used for hoists shrdl be so constructed
Only workmen actually engaged in removing the
that a brake is applied when the control lever or switch
formwork shall be allowed in the area during these
is not held in the operating position (dead-man’s
operations. Those engaged in removing the formwork
handle).
shall wear helmets, gloves and heavy soled shoes and
approved safety belts if adequate footing is not 17.4.8 The hoist tower shall be tied to a building or
provided above 2 m level. While cutting any tying structure at every floor level or at least every 3 m. The
wires in tension, care shall be taken to prevent backlash height of the tower shall not exceed 6 m after the last
which might hit a workman. tie or a lesser height as recommended by the
manufacturer. All ties on a hoist tower shall be secured
17.2.14.1 The particular order in which the supports
using right angled couples.
are to be dismantled should be followed according to
the instructions of the site engineer. 17.4.9 The hoist shall be capable of being operated
only from one position at a time. It shall not be operated
17.3 Ramps and Gangways from the cage. The operator shall have a clear view of
17.3.1 Ramps and gangways shall be of adequate all levels or, if he has not, a clear and distinct system
strength and evenly supported. They shall either have of signaling shall k employed.
a sufficiently flat slope or shall have cleats fixed to the 17.4.10 All hoist platform shall be fitted with guards
surface to prevent slipping of workmen. Ramps and and gates to a height of at least 1 m, to prevent materials
gangways shall be kept free from grease, mud, snow rolling/falling from the platform.
or other slipping hazards or,other obstructions leading
to tripping and accidental fall of a workman. 17.4.11 Where materials extend over the height of the
platform guards, a frame shall be fitted and the
17.3.1.1 Ramps and gangways meant for transporting materials secured to it during hoisting/lowering. (Care
materials shall have even surface and be of sufficient should be taken to ensure that neither the frame nor
width and provided with skirt boards on open sides. materials interfere or touch any part of the hoisting
mechanism.)
17.4 Materials Hoists
17.4.12 The platform of a goods hoist shall carry a
17.4.1 The hoist should be erected on a firm base,
notice stating:
adequately supported and secured. All materials
supporting the hoist shall be appropriately designed a) the safe working load; and
and strong enough for the work intended and free from b) that passengers shall not ride on the hoist.
defects.
17.4.13 All hoist operators shall be adequately trained
17.4.2 The size of the drum shall match the size of and competent, and shall be responsible for ensuring
the rope. Not less than two full turns of rope shall that the hoist is not overloaded or otherwise misued.
remain on the drum at rdl times. Ropes shall be securely
17.4.14 All hoists shall be tested and thoroughly
attached to the drum.
examined by a competent person before use on a site,
17.4.3 All ropes, chains and other lifting gear shall be after substantial alteration, modification or repair of
properly made of sound materials, free from defects hoists, and at least every 6 months.
and strong enough for the work intended. They shall
17.4.15 Every hoist shall be inspected at least once
be examined by a competent person who shall clearly
each week by a competent person and a record of these
certify the safe working load on each item and the
inspections kept. ‘
system.
17.5 Prestressed Concrete
17.4.4 Hoistways shall be protected by a substantial
enclosure at ground level, at all access points 17.5.1 In pre-stressing operations, operating,
and wherever persons may be struck by any moving maintenance and replacement instructions of the
part. supplier of the equipment shall be strictly adhered to.
17.4.5 Gates at access points should be at least 2 m 17.5.2 Extreme caution shall be exercised in all
high wherever possible. Gates shall be kept closed at operations involving the use of stressing equipment as
all times except when required open for immediate wires/strands under high tensile stresses become a
movement of materials at that landing place. lethal weapon.
17.4.6 All gates shall be fitted with electronic or 17.5.3 During the jacking operation of any tensioning

32 NATIONAL BUILDING CODE OF INDIA


T“-”--”-

element(s) the anchor shall be kept turned up close to before releasing the lifting equipment. The permanent
anchor plate, wherever possible, to avoid serious structural comections shall be established at the earliest
damage if a hydraulic line fails. opportunity.

17.5.4 Pulling-headers, bolts and hydraulic jacks/rams 17.7 Heated Concrete


shall be inspected for signs of deformation and failure.
Threads on bolts and nuts should be frequently When heaters are being used to heat aggregates and
inspected for diminishing cross section. Choked units other materials and to maintain proper curing
shall be carefully cleaned. temperatures, the heaters shall be frequently checked
for functioning and precautions shall be taken to avoid
17.5.5 Care shall be taken that no one stands in line
hazards in using coal, liquid, gas or any other fuel.
with the tensioning elements and jacking equipment
during the tensioning operations and that no one is 17.8 Structural Connections
directly over the jacking equipment when deflection
is being done. Signs and barriers shall be provided to 17.8.1 When reliance is placed on bond between
prevent workmen from working behind the jacks when precast and in-situ concrete the contact surface of the
precast units shall be suitably prepared in accordance
the stressing operation is in progress.
with the specifications.
17.5.6 Necessary shields should be put up immediately
behind the prestressing jacks during stressing 17.8.2 The packing of joints shall be carried out in
operations. accordance with the assembly instructions.

17.5.7 Wedges and other temporary anchoring devices 17.8.3 Levelling devices, such as wedges and nuts
shall be inspected before use. which have no load bearing function in the completed
structure shall be released or removed as necessary
17.5.8 The prestressing jacks shall be periodically prior to integrating the joints.
examined for wear and tear.
17.8.4 If it becomes necessary to use electric power
17.6 Erection of Prefabricated Members for in-situ work, the same should be stepped down to
17.6.1 A spreader beam shall be used wherever a safe level as far as possible.
possible so that the cable can be as perpendicular to
17.9 General
the members being lifted as practical. The angle
between the cable and the members to be lifted shall Workmen working in any position where there is a
not be less than 60°. falling hazard shall wear safety belts or other adequate
protection shall be provided.
17.6.2 The lifting wires shall be tested for double the
load to be handled at least once in six months. The 18 ADDITIONAL SAFETY REQUIREMENTS
guy line shall be of adequate strength to perform its FOR ERECTION OF STRUCTURAL STEEL
function of controlling the movement of members WORK
being lifted,
18.1 Safety Organization
17.6.3 Temporary scaffolding of adequate strength
shall be used to support precast members at The agency responsible for erecting the steel work
predetermined supporting points while lifting and should analyze the proposed erection scheme for
placing them in position and connecting them to other safety; the erection scheme should cover safety aspects
members. right from the planning stage up to the actual execution
of the work.
17.6.4 After erection of the member, it shall be guyed
and braced to prevent it from being tipped or dislodged 18.2 Safety of Workpersons
by accidental impact when setting the next member.
18.2.1 General
17.6.5 Precast concrete units shall be handled at
While engaging persons for the job the supervisor
specific picking points and with specific devices.
should check up and make sure that they are skilled in
Girders and beams shall be braced during transportation
the particular job they have to perform.
and handled. In such a way as to keep the members
upright. 18.2.1.1 The helmets shall be worn properly and at
all times during the work and shall conform to the
17.6.6 Methods of assembly and erection specified by
accepted standards [7(9)].
the designer, shall be strictly adhered to at site.
Immediately on erecting any unit in position, temporary 18.2.1.2 The safety goggles shall be used while
connections or supports as specified shall be provided performing duties which are hazardous to eye like

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 33


%’ “

drilling, cutting and welding. The goggles used shall pair of bridles slings can be placed far enough apart
conform to the accepted standards [7(15)] and should for them to be safe lifting points. The top flange of a
suit individual workers. truss, girder or long beam may be temporarily
reinforced with a structural member laid flat on top of
18.2.1.3 The welders and gas cutters shall be equipped
the member and secured temporarily.
with proper protective equipment like gloves, safety
boots, aprons and hand shields [see accepted standard 18.2.7 On deep girders, and even on some trusses, a
7( 15)]. The filter glass of the hand shield shall conform safety ‘bar’ running their full length will aid the riggers,
to the accepted standards [7(16)] and should be suitable fitters and others employed on the bottom flange or
to the eyes of the particular worker. bottom chord to work with greater safety. This can be
a single 16 mm diameter wire rope through vertical
18.2.1.4 When the work is in progress, the area shall
stiffeners of such members about one metre above the
be cordoned off by barricades to prevent persons from
bottom flange and clamped at the ends with wire rope
hitting against structural components, or falling into
clamps. If the holes cannot be provided, short eye bolts
excavated trenches or getting injured by falling objects.
can be welded to the webs of the girder at intervals to
18.2.1.5 Warning signs shall be displayed where be removed and the surface chipped or ground to leave
necessary to indicate hazards, for example (a) ’440 it smooth after all work on the piece has been
VOLTS’, (b) ‘DO NOT SMOKE’, (C) ‘MEN WORKING completed.
AHEAD’, etc. Hand lamps shall be of low voltage
18.2.8 Safety belts shall always be available at work
preferably 24 V to prevent electrical hazards.
spot to be used whenever necessary. The rope shall be
18.2.1.6 All electrically operated hand tools shall be chemically treated to resist dew and rotting. These shall ...
provided with double earthing, not be tied on sharp edges of steel structures. They
shall be tied generally not more than 2 m to 3 m away
18.2.2 Anchors for guys or ties shall be checked for
from the belt.
proper placement. The weight of concrete in which
the anchors are embedded shall be checked for uplift 18.2.9 On a guy derrick or climbing crane job, the
and sliding. tool boxes used by the erection staff shall be moved to
the new working floor each time the rig is Changed.
18.2.2.1 Split-end eye anchors shall only be used in
On a mobile crane job, the boxes shall be moved as
good, solid rock.
soon as the crane starts operating in a new area too far
18.2.2.2 The first load lifted by a guy derrick shall be away for the men to reach the boxes conveniently.
kept at a small height for about 10 min and the anchors While working a tall and heavy guy derrick, it is
immediately inspected for any signs or indications of advisable to control tension in guys by hand winches
failure. to avoid jerks, which may cause an accident.

18.2.3 When a number of trusses or deep girders is 18.2.10 The proper size, number and spacing of wire
loaded in one car or on one truck, all but one being rope clamps shall be used, depending on the diameter
lifted shall be tied back unless they have been tied or of the wire rope. They shall be properly fixed in
braced to prevent their falling over and endangering accordance with good practice [7( 17)]. They shall be
men unloading. checked as soon as the rope has been stretched, as the
rope, especially if new, tends to stretch under the
18.2.4 The erection gang shall have adequate supply applied load, which in turn may cause it to shrink
of bolts, washers, rivets, pins, etc, of the correct size. slightly in diameter. The clamps shall then be promptly
Enough number of bolts shall be used in connecting tightened to take care of this new condition. In addition,
each piece using a minimum of two bolts in a pattern the clamps shall be inspected frequently to be sure that
to ensure that the joint will not fail due to dead load they have not slipped and he tight enough.
and erection loads. All splice connections in columns,
18.2.11 When the men can work safely from the steel
crane girders, etc, shall be completely bolted or riveted
structure itself, this is preferable to hanging platforms
or welded as specified in the drawing before erection.
or scaffolds, as it eliminates additional operations,
18.2.5 Girders and other heavy complicated structural which in turn, reduces the hazard of an accident.
members may require special erection devices like
18.2.11.1 To aid men working on floats or scaffolds,
cleats and hooks, which can be shop assembled and
as well as men in erection gangs, or other gangs using
bolted or riveted or welded to the piece and may be
small material, such as bolts and drift pins, adequate
left permanently in the place after the work.
bolt baskets or similar containers with handles of
18.2.6 If a piece is laterally unstable when picked at sufficient strength and attachment to carry the loaded
its centre, use of a balance beam is advisable, unless a containers, shall be provided.

34 NATIONAL BUJLDING CODE OF INDIA


F-=

18.2.11.2 The men should be trained to use such 18.2.17.3 While using multilegged slings, each sling
containers, and to keep small tools gathered up and or leg shall be loaded evenly and the slings shall be of
put away in tool boxes when not in use. Material sufficient length to avoid a wide angle between the
shall not be dumped overboard when a scaffold is legs.
to be moved. Rivet heaters shall have safe containers
18.2.18 Rivetting Operations
or bucke~s for hot rivets left over at the end of the
clay. 18.2.18.1 Handling rivets

18.2.12 During the erection of tall buildings, it is Care shall be taken while handling rivets so that they
desirable to use nylon nets at a height of 3 m to 4 m to do not fall, strike or cause injury to men and material
provide safety to men, The safety net should be made below. Rivet catchers shall have false wooden bottoms
from man or machine-made fibre ropes which are UV to prevent rivets from rebounding.
stabli zed and conforming to the acceptable standard
18.2.18.2 Rivetting dollies
[7(18)].
Canvas, leather or rope slings shall be used for riveting
18.2.13 Safety Against Fire
dollies. Chain shall not be used for the purpose.
A fire protection procedure is to be set up if there is to
18.2.18.3 Rivetting hammers
be any flame cutting, burning, heating, rivetting or any
operation that could start a fire. For precautions to be Snaps and plungers of pneumatic riveting hammers
observed during welding and cutting operations, shall be secured to prevent the snap from dropping out
rcfcrcnce may be made to good practice [7( 19)]. of place. The nozzle of the hammer shall be inspected
periodically and the wire attachment renewed when
1S.2.13.1 The workers should be instructed not to
born.
throw objects like hot rivets, cigarette stubs, etc,
around. 18.2.18.4 Fire protection ~

18.2.13.2 Sufficient fire extinguishers shall be placed The rivet heating equipment should be as near as
at strategic points. Extinguishers shall always be placed possible to the place of work. A pail of water shall
in cranes, hoists, compressors and similar places. always be kept already for quenching the fire during
Where electrical equipments are involved, C02 or dry rivetting operations and to prevent fires when working
powdeg extinguishers shall be provided {see also good near inflammable materials.
practice [7(4)] ].
18.2.19 Welding and Gas Cutting
18.2.14 Riding on a load, tackle or runner shall be
18.2.19.1 For safety and health requirements in electric
prohibited.
gas welding and cutting operations, reference may be
18.2.15 The load shall never be allowed to rest on wire made to good practice [7(21)]. The recommendations
ropes. Ropes in operation should not be touched. Wire given in 18.2.19.2 to 18.2.19.4 are also applicable.
rope with broken strand shall not be used for erection
18.2.19.2 All gas cylinders shall be used and stored
work. Wire ropes/manila ropes conforming to
in the upright position only and shall be conveyed in
acceptable standards [7(20)] shall be used for guying.
trolleys. While handling by cranes they shall be carried
18.2.16 Lijting Appliances in cages. The cylinders shall be marked ‘full’ or
Precautions as laid down in 17.1.2 shall be followed. ‘empty’ as the case may be. Gas cylinders shall be
stored away from open flames and other sources of
18.2.17 Slinging heat. Oxygen cylinders shall not be stored near
18.2.17.1 Chains shall not be joined by bolting or combustible gas, oil, grease and similar combustible
wiring links together. They shall not be shortened by materials. When the cylinders are in use, cylinder valve
tying knots. A chain in which the links are locked, key or wrench shall be placed in position. Before a
stretched or do not move freely shall not be used. The cylinder is moved, cylinder valve shall be closed. All
chain shall be free of kinks and twists. Proper eye cylinder valves shall be closed when the torches are
splices shall be used to attach the chain hooks. being replaced or welding is stopped for some reason.
The cylinder valve and connections shall not be
18.2.17.2 Pulley blocks of the proper size shall be used
lubricated.
to allow the rope free play in the sheave grooves and
to protect the wire rope from sharp bends under load. 18.2.19.3 Gas cutting and welding torches shall be
Idle sling should not be carried on the crane hook lighted by means of special lighters and not with
alongwith a loaded sling. When idle slings are carried matches. The cables from welding equipment should
they shall be hooked. be placed in such a way that they are not run over by

PAR~ 7 CONSTRUCTIONAL PRACTICES AND SAFETY 35


traffic. Double earthing shall be provided. Before 19.3 Construct I~volv#ng the Use of Hot
undertaking welding operations near combustible Bitumiwnm Ttw IWtt&Ms
materials, suitable blanketing shall be provided and
19.3.1 Saf4iy Programme
fire extinguishers kept nearby. Welding shall not be
undertaken in areas where inflammable liquids and 19.3.1.1 General
gases are stored.
On all major works, an experienced and competent
18.2.19.4 Gas lines and compressed air lines shall foreman or supervisor shall be placed in-charge of the
be identified by suitable colour codes for easy work, and shall be made responsible for the strict
identification, to avoid confusion and to prevent fire observance of the safety rules. He shall stock the
and explosion hazards. necessary protective equipment, fire extinguishing
equipment, first-aid kit, etc. He shall also keep a record
18.3 Safety of Structure of the accidents taking place on any particular job, with
18.3.1 General reasons thereof, and shall suggest suitable remedial
measures to the management for prevention thereof.
The structure itself should be safeguarded during its
erection. The first truss of the roof system shall be 19.3.1.2 Protective covering
guyed on each side before the hoisting rope is detached Workers engaged on jobs involving handling of hot
from it. After the subsequent trusses and roof purlins bitumen, tar, and bituminous mixtures shall use
are erected, protective guides shall be firmly protective wears, such as boots and gloves, preferably
established and the required wind bracings shall be of asbestos or otherwise of rnbbeq goggles and helmet.
erected to prevent the whole structure being blown over No workers shall be permitted to handle such materials
by a sudden gale at night. Bracing and guying without wearing the needed protective covering.
precautions shall be taken on every structure until it is
complete. Guying shall be specifically done for trusses 19.3.1.3 Fire fighting arrangements
and structural components which after their erection When heating and handling of hot bituminous materials
form an erection device, On structures used for is to be done in the open, sufficient stocks of clean dry
temporary material storage overloading shall be sand or loose earth shall be made available at the work
avoided. site to cope with any resultant fires. When such
18.3.1.1 Erection of columns shall be immediately materirds are not available, nor are any suitable type
followed by vertical bracing between columns before of fire extinguishers provided at the work site in the
the roof structure is erected. open, and reliance has to be on using water for fighting
any fire, the water supply available should be in
19 MISCELLANEOUS ITEMS abundance and the water shall be applied to the f~e in
the form of spray. When heating of bituminous
19.1 Staircase Construction
materials is carried out in enclosed spaces, sufficient
While staircase is under construction, depending on number of properly maintained dry powder fire
the type of construction, namely, concrete or extinguisher or form extinguisher conforming to
brickwork, etc, suitable precautions shall be taken by accepted standards [7(21 )] shall be kept in readiness
way of support, formworks, etc, to prevent any on the work site.
collapse. Workmen or any other person shall not be
19.3.2 Sprayer, Spreader/Paver
allowed to use such staircases till they are tested and
found fit for usage by the Authority/engineer-in- 19.3.2.1 Sprayer
charge. Till the permanent handrails are provided, The sprayer shall be provided with a fire resisting
temporary provisions like ropes, etc, shall be provided screen. The screen shall have an observation window.
on staircases prior to commencement of use of such Piping for hot tar and bitumen shall be adequately
staircases. insulated to protect workers from injury by burns.
Flexible piping work under positive pressure shall be
19.2 Lift WelIs
of metal which shall be adequately insulated. Workers
Till the installation of the lift is completed, lift wells shall not stand facing the wind directions while
shall be protected with check boards or railings together spraying hot binder, lest it may fall on them causing
with notice boards, danger lights, etc, to precent burns.
persons accidentally falling into the wells. The
19.3.2.2 Spreader/Paver
handrails provided shall be capable of withstanding
pressure exerted due to normal bumping of an Spreaders in operation shall be protected by signrds,
individual against the same. signs or other effective means. People should be

36 NATIONAL BUILDING CODE OF INDIA


warned against walking over hot mixture laid. Gravel with hot bitumen or tar to a level that might cause
spreaders shall always keep a safe distance from danger when they are carried or hoisted. Enough space
sprayer. Elevated platforms on spreaders shall be shall be left in vessels for expansion of binder when
protected by suitable railing and be provided with an heated.
access ladder.
19.3.3.7 Bitumen/Tar shall be kept dry and to avoid
19.3.3 Equipment for Heating of Bitumen and Tars fire due to foaming, boiler shall have a device that
prevents foam from reaching the burners or anti-
19.3.3.1 Tanks, vats, kettles, pots, drums and other
foaming agents shall be used to control the same.
vessels for heating tar, bitumen and other bituminous
Alternatively to avoid fire due to foaming, the heating
rndterials shall be:
shall be at low temperature till the water entrapped, if
a) adequately resistant to damage by heat, any, is completely evaporated. Any water present in
transportation, etc; the boiler shall also be drained before using it for
b) capable of holding a full load without danger heating binders. No open light shall be used for
of collapse, bursting or distortion; ascertaining the level of binder in boilers. If a burner
c) provided with a close fitting cover suitable goes out, the fuel supply shall be cutoff and the heating
for smothering a fire in the vessel or tube shall be thoroughly blown out by the fan so as to
protection from rain; and prevent a back fire.

d) leak proof, and provided with suitable outlets 19.3.3.8 Cutbacks shall not be heated over an open
which can be controlled for taking out the hot flame unless a water jacket is used, While they are
material. being heated the vessel shall be kept open.

19.3.3.2 Suitable indicator gauges shall be used to 19.3.3.9 Piping shall not be warmed with burning rags
ascertain level and temperature of the material in the and instead blow-lamps or similar devices shall be used.
boiler. On no account shall workers be allowed to peep
19.3.3.10 Spilled bitumen or tar shall be promptly
into the boiler for this purpose. For ascertaining levels,
cleaned up around boilers.
in small plants, dipstick may also be used.
19.3.3.11 Inspection openings shall not be opened
19.3.3.3 Gas and oil-fwed bitumen and tar kettles or
while there is any pressure in the boiler.
pots shall be equipped with burners, regulators and
safety devices of types approved by the Authority. 19.3.3.12 When tanks are cleaned by steam, adequate
Heating appliances for vessels shall distribute the heat precautions shall be taken to prevent any built up of
uniformly over the heating surface so as to avoid pressure.
overheating. In case of bituminous mixtures using
19.3.4 Handling Bitumeflar
mineral aggregates filler together with bitumen, it is
preferable to have some means for stirring as well. Only Bitumen/tar shall not be heated beyond the temperature
vessels heated by electricity shall be used inside recommended by the manufacturer of the product.
buildings. Tar boilers shall never be used on While discharging heated binder from the boiler,
combustible roof. workers shall not stand opposite to the jet so as to avoid
the possibility of hot binder falling on them. The
19.3.3.4 Buckets for hot bitumen, bituminous
container shall be handled only after closing the control
materials of tar shall have:
valve. While handling hoi bitumenhar, workers shall
a) the bail or handle firmly secured, and exercise scrupulous care to prevent accidental spillage
b) a second handle near the bottom for tipping. thereof. The buckets and cans in which the hot material
is carried from boiler shalb’be checked before use to
19.3.3.5 Bitumen or tar boilers mounted on wheels
ensure that they are intact and safe. Mops and other
for easy transport or towing shall preferably be
applicators contaminated with bituminous materials
provided with hand pumps for spraying purposes.
shall not be stored inside buildings.
19.3.3.6 Vessels in operation shall be kept at a safe
19.3.5 Bitumen Plants
distance from combustible materirds. When vessels are
used in confined spaces, the gases, fumes and smoke Safety requirements shall be in accordance with good
generated shall be removed by exhaust ventilation or practice [7(22)].
by forced ventilations. Vessels that are being heated
19.4 Timber Structure
shall not be left unattended, Pieces of bituminous
material shall not be thrown into the hot vessels so as Preventive measures against hazards in work places
to cause splashing. Covers shall be kept closed when involving construction of timber structures shall be
vessels are not in use. Containers shall not be filled taken in accordance with good practice [7(23)].

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 37


20 FINISHES 23.1.2 All electrical circuits, other than those required
for illumination of the site at night, shall be switched
20.1 Painting, Polishing and Other Finishes
off at the close of day’s work. The main switch board
Only the quantity of paint, thinner and polish required from which connections are taken for lighting, power
for the day’s work should be kept at the work spot. operated machinery, etc, shall be located in an easily
accessible and prominent place. No articles of clothing
20.1.1 All containers of paint, thinner and polish which
nor stores shall be kept at the back of or over the board
are not in actual use should be closed with tight fitting
or anywhere near it. One 3 kg/4.5 kg C02 extinguisher
lids and kept at a safe place away from the actual work
or one 5 kg dry powder extinguisher shall be provided
site.
near the switch board.
20.1.2 A 5 kg dry powder fire extinguisher conforming
23.2 Permanent Electrical Installations
to acceptable standards [7(23)] shall be kept handy.
Besides the fire safety measures for electrical
20.1.3 Metal receptacles with pedal operated metal lids
installations covered under 23.1, safety in electric
shall be kept handy at the work site for depositing used
installations in buildings and installations of lifts shall
cotton ragslwaste. The contents of such receptacles
be in accordance with Part 8 ‘Building Services,
shall be disposed off before the end of each day’s work
Section 2 Electrical and Allied Installations and
at a safe place, preferably by burning under proper
Section 5 Installation of Lifts and Escalators’.
supervision.

20.1.4 All containers of paint shall be removed from 24 GENERAL REQUIREMENTS


the work site and deposited in the paint store before the 24.1 Sanitation
close of day’s work. Used paintbrushes shall be cleaned
and deposited in the store alongwith the containers. a) Adequate toilet facilities shall be provided for
the workmen within easy access of their place
20.1.5 Some paints/polishing and finishing materials of work. The total number to be provided shall
are injurious to the health of workmen. Adequate be not less than one per 30 employees in any
protective clothing, respiratory equipment, etc, shall one shift.
be provided for the use of workmen during such
b) Toilet facilities shall be provided from the
operations where necessary.
start of building operations, and connection
21 FRAGILE FIXTURES to a sewer shall be made as soon as practicable.
c) Every toilet shall be so constructed that the
21.1 It shall be ensured that sufficient number of
occupant is sheltered from view and protected
workmen and equipment are provided to carry the from the weather and falling objects.
fragile fixtures like sanitary fittings, glass panes, etc,
d) Toilet facilities shall be maintained in a
to prevent injury to workmen due to accidental
sanitary condition. A sufficient quantity of
dropping of such fixtures.
disinfectant shall be provided.
22 SAFETY IN SPECIAL OPERATIONS e) An adequate supply of drinking water shall
be provided, and unless connected to a
22.1 Safety in compressed airwork, drilling, blasting
municipal water supply, samples of the water
and welding operations shall be in accordance with
shall be tested at frequent intervals by the
good practice [7(25)].
Authority.
23 ELECTRICAL INSTALLATIONS AND LIFTS f) Washing facilities shall be installed, and when
practicable shall be installed, and when
23.1 Temporary Electrical Wiring
practicable shali be connected to municipal
23.1.1 Frayed and/or bare wires shall not be used for water supply and shall discharge to a sewer.
temporary electrical connections during construction. !3) Natural or artificial illumination shall be
All temporary wiring shall be installed and supervised provided.
by a competent electrician. Adequate protection shall
24.2 Fire Protection
be provided for all electrical wiring laid on floor which
may have to be crossed over by construction machinery 24.2.1 In addition to the provision of fwe extinguishers,
or by the workmen. All flexible wiring connecting the as specified in this Part of the Code, other fire
electrical appliances shall have adequate mechanical extinguishing equipment shall also be provided and
strength and shall preferably be enclosed in a flexible conveniently located within the building under
metal sheath. Overhead wires/cables shall be so laid construction or on the building site, as required by the
that alley leave adequate head room. Authority.

38 NATIONAL BUILDING CODE OF INDIA


24.2.1.1 All fire extinguishers shall be maintained in should at all times, be not more than one floor below
a serviceable condition at all times in accordance with the floor under construction.
good practice [7(4)] and all necessary guidelines
24.2.3.4 A substantial box, preferably of metaJ, should
regarding fire protection at workplaces followed in
be provided and maintained near each hose outlet. The
accordance with good practice [7(2)].
box should contain adequate lengths of hose to reach
24.2.1.2 It shall be ensured that all workmen and all parts of the floor as well as a short branch fitted
supervisory staff are fully conversant with the correct with 12 mm or 20 mm nozzle.
operation and use of fire extinguishers provided at the
24.2.4 Close liaison shall be maintained with the local
construction site.
fire brigade, during construction of all buildings
24.2.1.3 Telephone number of local fire brigade above 15 m in height and special occupancies, like
should be prominently displayed near each telephone educational; assembly, institutional, industrial, storage,
provided at construction site. hazardous and mixed occupancies with any of the
aforesaid occupancies having area more than 500 mz
24.2.1.4 Watch and ward services should be provided
on each floor.
at construction sites during holidays and nights.
24.2.5 It is desirable that telephone system or other
24.2.2 Access shall be provided and maintained at all
means of inter-communication system be provided
times to all fire fighting equipment, including fire hose,
during the construction of all buildings over 15 m in
extinguishers, sprinkler valves and hydrants.
height or buildings having a plinth area in excess
24.2.2.1 Approach roads for fire fighting should be of 1000 m2.
planned, properly maintained and kept free from
24.2.6 All work waste, such as scrap timber, wood
blockage. Width of approach road should be not less
shavings, sawdust, paper, packing materials and oily
than 5 m to facilitate fire fighting operations.
waste shall be collected and disposed of safely at the
24.2.2.2 Emergency plan and fire order specifying the end of each day’s work. Particular care shall be taken
individual responsibility in the event of fire should be to remove all waste accumulation in or near vertical
formulated and mock drills should be practised shaft openings like stairways, lift-shaft, etc.
periodically in case of large and important construction
24.2.7 An independent water storage facility shall be
sites to ensure upkeep and efficiency of fire fighting
provided before the commencement of construction
appliances.
operations for fire-fighting purposes. It shall be
24.2.2.3 Periodical inspection should be carried out maintained and be available for use at all times.
to identify any hazard and proper records maintained
24.2.8 Fire Cut-o~s
and follow up action taken.
Fire walls and exit stairways required for a building
24.2.2.4 Evaluation facilities and fire exits should be
should be given construction priority. Where fiie doors,
provided at all locations susceptible to fire hazards.
with or without automatic closing devices, are
24.2.3 Where the building plans require the installation stipulated in the building plans they should be hung as
of fixed fire fighting equipment, such as hydrants, stand soon as practicable and before any significant quantity
pipes, sprinklers and underground water mains or other of combustible material is introduced in the building.
suitable arrangements for provision of water shall be
installed, completed and made available for permanent 24.2.8.1 As the work progresses, the provision of
use as soon as possible, but in any case not later than permanent stairways, stairway enclosures, fire walls
the stage at which the hydrants, etc, are required for and other features of the completed structure which
use as specified in 24.2.3.1 to 24.2.3.4. will prevent the horizontal and vertical spread of fire
should be ensured.
24.2.3.1 A stand pipe system (landing valves),
permanent in nature shall be installed and made 24.3 Clothing
available before the building has reached the height
24.3.1 It shall be ensured that the clothes worn by the
of 15 m above the grade, and carried up with each
workmen be not of such nature as to increase the
floor.
chances of their getting involved in accident to
24.2.3.2 The standpipe (landing valvelinternal fire themselves or to others. As a rule, wearing of
hydrant) and its installation shall conform to the CHADDARS or loose garments shall be prohibited.
accepted standards [7(26)].
24.3.2 Workmen engaged in processes which splash
24.2.3.3 The standpipe shall be carried up with each liquid or other materials which will injure the skin shall
floor and securely capped at the top. Top hose outlets, have enough protective clothing to cover the body.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 39


24.3.3 Individuals engaged in work involving use of certainly delay the decay of the building structure.
naked flames (such as welding) shall not wear synthetic Though the building may be designed to be very
fibre or similar clothing which increases the risk of durable it needs maintenance to keep it in good
fire hazards. condition.

24.4 Safety Measures Against Fall Prevention 26.2 Terminology

Persons working at heights may use safety belts and For the purpose of this Section, the following
harnesses. Provision of cat-walks, wire mesh, railings definitions shrdl apply.
reduces chances of fall-ladder and scaffoldings,
26.2.1 Maintenance — The combination of all
stagings etc, should be anchored on firm footing and
technical and associated administrative actions
should be secured and railing should be provided as
intended to retain an item in or restore it to a state in
far as possible. All accesses should be barricaded to
which it can perform its required function.
prevent accidental fall, For details as fall prevention
reference may be made to good practice [7(27)]. 26.2.2 Maintenance Management — The organization
of maintenance within an agreed policy. Maintenance
24.5 Falling Materials Hazard Prevention
can be seen as a form of ‘steady state’ activity.
Preventive measures against falling materials hazards
26.2.3 Building Fabric — Elements and components
in work places shall be taken in accordance with good
of a building other than furniture and services.
practice [7(28)].
26.2.4 Building Maintenance — Work undertaken to
24.6 Dkposal of Debris
maintain or restore the performance of the building ...
Preventive measures against hazards relating to fabric and its services to provide an efficient and
disposal of debris shall be taken in accordance with acceptable operating environment to its users.
[7(29)].
26.2.5 House Keeping — The routine recurring work
25 CONSTRUCTION MACHINERY which is required to keep a structure in good condition
so that it can be utilized at its original capacity and
25.1 Specification and requirements of construction efficiency along with proper protection of capital
machinery used in construction or demolition work investment, throughout its economic life.
shall conform to accepted standards [7(30)].
26.2.6 Owner— Person or body having a legal interest
25.2 For safety requirements for working with in a building. This includes freeholders, leaseholders
construction machinery, reference may be made to or those holding a sub-lease which both bestows a legal
good practice [7(3 l)]. right to occupation and gives rise to liabilities in respect
of safety or building condition.
25.3 Petroleum powered air compressors, hoists,
derricks, pumps, etc, shall be so located that the In case of lease or sub-leaseholders, as far as ownership
exhausts are well away from combustible materials. with respect to the structure is concerned, the structure
Where the exhausts are pipes to outside the building of a flat or structure on a plot belongs to the rdlottee/
under construction, a clearance of at least 150 mm shall lessee till the allotment/lease subsists.
be maintained between such piping and combustible
26.2.7 Confined Space — Space which may be
material.
inadequately ventilated for any reason and may result
SECTION 4 MAINTENANCE in a deficiency of oxygen, or a build-up of toxic gases,
e.g. closed tanks, sewers, ducts, closed and unventilated
MANAGEMENT, REPAIRS, RETROFITTING
rooms, and open topped tanks particularly where
AND STRENGTHENING OF BUILDINGS
heavier than air gases or v%pours may be present.
26 MAINTENANCE MANAGEMENT
26.3 Building Maintenance
26.1 Maintenance management of building is the art
26.3.1 General
of preserving over a long period what has been
constructed. Whereas construction stage lasts for a Any building (including its services) when built has
short period, maintenance continues for comparatively certain objectives and during its total economic life, it
very large period during the useful life of building. has to be maintained. Maintenance is a continuous
Inadequate or improper maintenance adversely affects process requiring a close watch and taking immediate
the environment in which people work, thus affecting remedial action. It is interwoven with good quality of
the overall output. In the post construction stage the house keeping. It is largely governed by the quality of
day to day maintenance or upkeep of the building shall original construction. The owners, engineers,

40 NATIONAL BUILDING CODE OF INDIA


constructors, occupants and the maintenance agency structures are vulnerable to the effects of
are all deeply involved in this process and share a chlorine used in water.
responsibility. Sitnation in which all these agencies e) User — The maintenance requirements of
merge into one is ideal and most satisfactory. buildings and their various parts are directly
related to the type and intensity of use they
There are two processes envisaged, that is, the work
receive.
carried out in anticipation of failure and the work
carried out after failure. The former is usually referred 26.3.2.2 lnjluence of design
to as preventive maintenance and the latter as corrective
maintenance. The prime objective of maintenance is The physical characteristics, the life span and the
to maintain the performance of the building fabric and aesthetic qualities of any building depend on the
its services to provide an efficient and acceptable considerations given at the design stage. All buildlngs,
however well designed and conscientiously built, will
operating environment to its users.
require repair and renewal as they get older.
26.3.1.1 Maintenance in general term can be identified
However, for better performance of the building
in the following broad categories.
envelop, the following are the ways to minimize
a) Cleaning and servicing — This is largely of troubles at the later stage.
preventive type, such as checking the efficacy
a) Minimize defects during construction and
of rain water gutters and servicing the
mechanical and electrical installations. This design,
covers the house keeping also. b) Detail and choose materials during construction
so that the job of maintenance is less onerous.
b) Rectification and repairs —This is also called
periodical maintenance work undertaken by, 26.3.2.2.1 In addition to designing a building for
say, annual contracts and including external structural adequacy, consideration should also be given
replastering, internal finishing etc. to environmental factors such as moisture, natural
c) Replacements — This covers major repair or weathering, corrosion and chemical action, user wear
restoration such as reproofing or re-building and tear, pollution, flooding, subsidence, earthquake,
defective building parts. cyclones etc.

26.3.2 Factors Affecting Maintenance 26.3.2.2.2 A list of common causes for maintenance
problems is given in Annex C for guidance. However,
26.3.2.1 Maintenance of the buildings is influenced
no such list is likely to be entirely comprehensive.
by the following factors:
a) Technical factors — These include age 26.3.3 Maintenance Policy
of building, nature of design, material The policy should cover such items as the owner’s
specifications, past standard of maintenance anticipated future requirement for the building taking
and cost of postponing maintenance. account of the building’s physical performance and
b) Policy — A maintenance policy ensures that its functional suitability. This may lead to decisions
value for money expended is obtained in regarding:
addition to protecting both the asset value and
a) the present use of the building anticipating
the resource value of the buildings concerned
any likely upgradings and their effect on
and owners.
the life cycles of existing components or
c) Financial and economics factors — (see engineering services; and
26.9).
b) a change of use for @e building and the effect
d) Environmental — All buildings are subject to
of any conversion ‘work on the life cycles of
the effects of a variety of external factors such
existing components or engineering services.
as air, wind precipitation, temperature etc.
which influence the frequency and scope of 26.3.4 Maintenance Work Programmed
maintenance.
The programming of maintenance work can affect an
The fabric of building can be adversely owner or his activities in the following ways:
affected as much by the internal environment
as by the elements externally. Similar factors a) maintenance work should be carried out at
of humidity, temperature and pollution should such times as are likely to minimize any
be considered. Industrial buildings can be adverse effect on output or function.
subject to many different factors subject to b) programme should be planned to obviate as
processes carried out within. Swimming pool far as possible any abortive work.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 41


This may arise if upgrading or conversion 26.3.7.2 Feed back should aim at the following:
work is carried out after maintenance work
a) User satisfaction,
has been completed or if work such as
b) Continuous improvement, and
rewiring is carried out after redecoration.
c) Participation by all.
c) any delay in rectifying a defect should be kept
to a minimum only if such delay is likely to 26.3.7.3 Source of information
affect output or function. The cost of
The information on feed back can be obtained from
maintenance increases with shortening
the following:
response times.
d) maintenance work, completed or being a) Occupants,
carried out should comply with all statutory b) Inspections,
and other legal requirements. c) Records, and
26.3.5 Maintenance Guides d) Discussions.

An owner responsible for a large number of buildings 26.3.8 Means of Effecting Maintenance
may have established procedures for maintenance. 26.3.8.1 Responsibility
When an owner is responsible for the maintenance of
only one building or a small number of buildings, the Some maintenance work will be carried out by
preparation of a guide tailored to suit each particular the occupier of a building or by the occupier’s
building, can offer significant advantages. Such a guide representative. In the case of leasehold or similar
should take into account the following: occupation not all maintenance may be the
responsibility of occupier. Responsibility of common
a) type of construction and residual life of the
areas may be clearly defined.
building, and
b) environment and intensity of use (see 26.3.2). 26.3.8.2 Maintenance work sub-divided into major
repair, restoration, periodical and routine or day-to-day
The guide may form part of a wider manual covering operations will be undertaken by one of the following:
operational matters.
a) Directly employed labour,
26.3.6 Planning of Maintenance Work
b) Contractors, and
Work should take account of the likely maintenance c) Specialist contractors under service agreement
cycle of each building element and be planned or otherwise.
logically, with inspections being made at regular
26.3.8.3 The merits of each category for typical
intervals. Annual plans should take into account
maintenance work must be considered because
subsequent years’ programmed to incorporate items
optimum use of resources appropriate to tasks in a
and to prevent additional costs. It should be stressed
given situation is an important element of policy.
that the design of some buildings can lead to high
indirect costs in maintenance contracts and therefore, 26.3.8.4 The success of contracting out depends on
careful planning can bring financial benefits. Decisions the nature of the services, conditions in which
to repair or replace should be taken after due contracting is undertaken (the tendering process), how
consideration. the contract is formulated and subsequent monitoring
of service quality. The important consideration in the
26.3.7 Feed Back
decision to contract out is whether a contractor can
26.3.7.1 Feed back is normally regarded as an ensure a socially desirable quantity and quality of
important procedure of providing information about service provision at, a reasonable cost to the
the behaviour of materials and detailing for the benefit consumers.
of the architectiengineer designing new buildings,
which will result in lessening maintenance costs. It is 26.4 Access
an equally valuable source of information for
26.4.1 General
the persons responsible for maintenance. Every
maintenance organization should develop a sample All maintenance activities including any preliminary
way of communicating its know how, firstly for benefit survey and inspection work require safe access and in
of others in the organization and secondly for the some situations this will have to be specially designed.
benefit of the building industry as a whole. There Maintenance policy, and maintenance costs, will be
should be frank and recorded dialogue on an on-going much influenced by ready or difficult access to the
basis between those who occupy and care for buildings fabric and to building services. Special precautions and
and those who design and construct them. access provisions may also need to be taken for roof

42 NATIONAL BUILDING CODE OF INDIA


work or for entry into confined spaces such as ducts or 26.5.2 Use of Building Records
voids.
26.5.2.1 All personnel involved in the maintenance
26.4.2 Access Facilities of the building should be made aware of the existence
of the buildlng records.
26.4.2.1 Permanent accessibility measures should be
provided at the design stage only for all the areas for 26.5.2.2 Known hazardous areas should be explicitly
safe and proper maintenance. It is a matter on which marked on the records as well as being marked on
those experienced in the case of the building can make site and should be pointed out to such personnel
an important contribution at design stage in the interest together with any system of work adopted for use in
of acceptable maintenance costs. such areas.

26.4.2.2 A wide variety of temporary access equipment 26.5.2.3 Records are of value only if they are kept up
may appropriately be provided for maintenance work, to date and arrangements for this should be included
ranging from ladders to scaffoldings or powered lift in any provision that may be made for records.
platforms.
26.5.2.4 Records should be readily accessible for use
26.4.2.3 Wherever possible it is better to provide and the place of storage should take into account the
permanent access facilities such as fixed barriers, form of the records and the conditions needed to keep
ladders, and stairways. When such permanent access them from damage of any kind. It is recommended
facilities are provided necessary arrangement may be that a duplicate set of records is kept in a secure place
included in maintenance plans for their regular other than building itself and is kept up to date.
inspection, maintenance and testing.
26.5.3 Following should be typical contents of the
26.4.2.4 All personnel employed for carrying out maintenance records:
maintenance should be provided with the necessary
a) A brief history of property, names and
protective clothing and equipment and instructed in
addresses of consultants and contractors.
its use.
b) Short specifications, constructional processes,
26.4.2.5 When physical access is not possible in components, material finishes, hidden
situations such as wall cavities, drains etc, inspections features, special features etc.
may be made with the aid of closed circuit television c) “As built” plans and as subsequently altered
or optical devices such as endoscopes. with sections, elevations and other detailed
drawings.
26.4.3 Access to Confined Spaces
d) Foundation and structural plans/sections such
26.4.3.1 Ventilation as concrete reinforcement drawings.
Special precautions need to be taken when entering a e) Detail specification of all materials incorporated,
confined space. Such confined spaces should be for example, concrete mix, species and grades
adequately ventilated, particularly before being of timber etc. Potentially hazardous materials
entered, to ensure that they are free from harmful and types or methods of construction that
concentrations of gases, vapours other airborne under some circumstances may become
substances and that the air is not deficient in oxygen. hazardous may be identified.
f) Information on house keeping and routine
26.4.3.2 Lighting
maintenance with details of internal and
Good lighting is necessary in order that maintenance external surfaces and decorations, schedule
work can be carried out satisfactorily. This is of cleaning, inspection and maintenance.
particularly important in confined spaces. When g) Means of operating mechanical, electrical and
the normal lighting is inadequate it should be plumbing installations.
supplemented by temporary installations. These h) Description of renovations, extensions,
should provide general and spot illumination as adaptations and repair to each elements.
appropriate.
j) All plant, machinery and propriety articles
including manufacturers trade literature
26.5 Records
and instructions for installation, use and
26.5.1 General maintenance.
Good records can save owners and users/occupiers k) Methods of work used in construction such
much unnecessary expense and reduce potential as assembly of prefabricated units.
hazards in exploration work when faults arise. m) All information related to fire such as:

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 43


1) Location and service arrangements of all terminal components. Each duct and each
fire alarm and call points; terminal component should be marked with
2) Location and service arrangements of all its size, the air quantity flowing and other
extinguishers, hose reels and other fue relevant balancing data, and
fighting installations; e) the location and identity of each room or space
3) Location of all fire compartment walls, housing plant, machinery or apparatus.
doors, floors and screens; 26.5.4.2 Drawings
4) Location of all areas of exceptional fire
hazard; Drawings should record the following as installed:

5) Fire escape routes; a) detailed general arrangements of boiler


6) Details of application of any fm protection houses, machinery spaces, air handling planta,
treatment; and tank rooms and other plant or apparatus,
7) Location details and description of any including the location, identity, size and rating
installation for smoke control or protection of each apparatus, The information with
of escape routes. respect to the size and rating can be presented
in schedule form;
n) There should be a wall chart showing at a
glance the various operations which have to b) isometric or diagrammatic views of boiler
be undertaken. Line drawings of buildings are houses, plant rooms, tank rooms and similar
always useful. machinery, including valve identification
charts. It is useful to frame and mount a
P) Records of security measures should be
copy of such drawings on the wall of the .-
known to authorized personnel only.
appropriate room, and
q) Where no records exist, information should
be slowly built up as it becomes available c) comprehensive diagrams that show power
during the course of maintenance work. wiring and control wiring andlor pneumatic
or other control piping including size, type
r) Use of computers for storing information may
or conductor or piping used and identifying
be preferred.
the terminal points of each.
26.5.4 Mechanical Records
26.5.5 Electrical Records
26.5.4.1 Documentation
Documentation should record the following including
Documentation should record the following as locations, as installed:
installed:
a) main and submain cables, showing origin,
a) the location, including level if buried, of all route, termination, size and @e of each cable;
public service connections (for example, fuel cables providing supplies to specialist
gas and cold water supplies) together with the equipment, for example, computers, should
points of origin and termination, size and be identified separately; and
materials of pipes, line pressure and other
b) lighting conduits and final subcircuit cables,
relevant information;
showing origin, route, termination and size
b) the layout, location and extent of all piped of each, together with the number and size of
services showing pipe sizes, together with all cables within each conduit. The drawings
valves for regulation, isolation and other should indicate for each conduit or cable,
purposes as well as the results of all balancing, whether it is run on the surface or concealed,
testing and commissioning data; for example, in a wall chase, in a floor screed,
c) the location, identity, size and details of all cast in-situ, above a false ceiling etc.
apparatus and all control equipment served
These drawings should also indicate the locations of
by, or associated with, each of the various
lighting fittings, distribution boards, switches, draw-
services together with copies of any test
in-boxes and point boxes, and should indicate circuitry:
certificates for such apparatus where
appropriate. The information with respect to a) location and purpose of each emergency
size and details may be presented in schedule lighting fitting including an indication of the
form; circuit to which it is connected;
d) the layout, location and extent of all air ducts ~) single and three phase power conduits and
showing dampers and other equipment, final subcircuit cables showing locations of
acoustic silencers, grilles, diffusers or other power distribution boards, motors, isolators,

44 NATIONAL BUILDING CODE OF INDIA


starters, remote control units, socket outlets different approach if it is to be handled with maximum
and other associated equipment; economy and efficiency. A more detailed inspection
c) other miscellaneous equipment, conduits and covering all parts of a building is needed to determine
cables; what work should be included in cyclic and planned
d) lightening conductor, air terminak, conductors, maintenance programme.
earth electrodes and test clamps; 26.6.2 Frequency of Inspection
e) location of earth tapes, earth electrodes and
Inspection should be carried out at the following
test points other than those in (f); and
frequencies:
9 cables providing earth circuits for specialist
equipment, for example computers, should be a) Routine — Continuous regulm observations
identified separately, should be undertaken by the building user as
part of the occupancy of building. Feed back
Documentation should also include, when applicable.
resulting from this type of observation should
a) distribution diagrams or schedules to show be encouraged.
size, type and length (to within 1 m) of each b) General — Visual inspections of main
main and submain cable, together with the elements should be made annually under the
measured earth continuity resistance of each; supervision of suitably qualified personnel at
b) schedule of lighting fittings installed stating appropriate times.
location, manufacturer and type or catalogue c) Detailed — The frequency of full inspection
number together with the type or of the building fabric by suitably qualified
manufacturer’s reference, voltage and wattage personnel should not normally exceed a 5 year
of the lamp installed; period.
c) schedule of escape and emergency lighting 26.6.2.1 Inspection schedule
fittings installed stating location,
manufacturer, type or catalogue number The preparation of a specific schedule should be
together with the type or manufacturer’s encouraged. Once prepared, it can be used for
reference, voltage and wattage of the lamp subsequent inspections.
installed. For battery systems the position of 26.6.3 Inspection of Engineering Services
the battery, its ampere hour rating and battery
system rated endurance in hours should be Engineering services generally have a shorter life
stated; expectancy than building fabric and because of their
d) records of smoke detectors, sprinklers, fire dynamic function should be subjected to more frequent
precautions; inspections and maintenance.

e) incoming supply details; the type of system, 26.6.3.1 Inspection of services should be carried out
voltage, phases, frequency, rated current and for three purposes as follows:
short circuit level, with the details of the
a) to check if maintenance work is required,
supply protection and time of operation as
appropriate; b) to check if maintenance work is being
adequately carried out, and
g) main switchgear details; for purpose made
equipment this should include a set of c) for safety reasons to comply with
manufacturers’ drawings and the site layout; statutory requirements and if required,
with recommendations of other relevant
h) transformer, capacitor and power plant
organizations. ,’
details; the leading details should be given,
for example, for transformers the V.A rating, 26.6.3.2 The frequency of inspections for purpose
voltages and type of cooling; and (a) will depend upon types of plant and system
j) Completion certificate, according to the manufacturer’s recommendations and subjective
Indian Electricity Act. judgement. Frequencies for purpose (b) should be
carried out on an annual basis.
26.6 Inspections
26.6.3.3 Method of inspection
26.6.1 General
The limited life of building services means it is
Regular inspections are actual part of the procedures important to record their residual life so that their
for the maintenance of buildings. They are needed for replacement can be budgeted for, and inspection
a variety of purposes and each purpose requires a methods should be arranged accordingly.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 45


..,, . . . ... . . . ... ,.. e .-mw

E-._. , ....”..____._~~ ,?, -.,.’.


,,, .,,

A checklist of items of plant to be inspected should be wear to the various components. Examination of the.
considered. Detailed specifications of how inspections equipment shall reveal any need for conditioning of
should be carried out are necessary because a simple the contact system, lubrication and adjustment of the
visual inspection is unlikely to show whether plant is mechanisms.
operating correctly and efficiently.
26.7.2.2 Post fault maintenance
Inspections frequently necessitate the use of
When there is a breakdown in the system and certain
appropriate instruments by oompetent persons, An
parts are identified for the replacement and then the
example of this is the inspections carried out to check
maintenance/repair of the defective part away from the
compliance with statutory requirements.
operating environment is covered under post fault
When instruments are used it is important that adequate maintenance.
training is provided in the use of the instruments and
26.7.3 Guidelines for the Maintenance of Electrical
the interpretation of the results.
Appliances
26.6.4 Records of all inspections should be kept.
26.7.3.1 Unintemupted and hazard free functioning of
26.6.5 Inspection Report the electrical installations are the basic parameters of
Inspection report may be prepared in the format as maintenance. The equipment should be restored to
given in Annex D. correct working conditions. Special attention should
be paid to the items and settings that might have been
26.7 Maintenance of Electrical Appliances disturbed during the operational phase. Loose and
26.7.1 Planning ofiklaintenance Work extraneous equipment or wiring give rise to potential
safety hazards. All covers and locking arrangements
26.7.1.1 If the authorized person has complete should be properly checked and secured to achieve
knowledge of the electrical appliances to be worked original degree of protection.
upon, then safety will be more assured. If the person
attending to the job is not technically competent to 26.7.3.2 Guidelines to be followed for the maintenance
handle the job then more careful planning is required of electrical equipments to ensure their smooth
before hand. functioning are given in Annex E.

26.7.1.2 Repetitive nature of jobs involve little or no 26.8 Operating and Maintenance Manuals
pre-planning whereas infrequent nature of jobs may The engineering services within buildings frequently
need careful planning even if the person attending the are dynamic, involving complex systems of integrated
job is technically competent. plant items. Operation of such plant can require detailed
26.7.1.3 Planned routine maintenance will facilitate knowledge and direction. Maintenance can also require
continued safe and acceptable operation of an electrical extensive information to be available. It is, therefore,
system with a minimum risk of breakdown and important to have suitable operating and maintenance
consequent interruption of supply. manuals to provide the necessary guidance. These
should be included as part of the contractual
26.7.1.4 As far as the electrical equipments/ requirements for new installations and should ideally
installations are concerned, it is not possible to laydown be prepared as reference documents for existing
precise recommendations for the interval between the installations where no such information exists.
maintenance required. The recommendation for
frequency of maintenance in this regard from the 26.9 For details on labour management concerning
manufacturer is more relevant. The manufacturer building maintenance, reference shall be made to good
should be requested to specify minimum maintenance practice [7(32)].
frequency under specified conditions. These intervals 26.10 For details on financial management concerning
depend greatly upon the design of the equipment, the building maintenance, reference shall be made to good
duty that it is called onto perform and the environment practice [7(33)].
in which it is situated.
27 PREVENTION OF CRACKS
26.7.2 Following two types of maintenance are
envisaged. 27.1 Cracks in buildings are of common occurrence.
A building component develops cracks whenever stress
26.7.2.1 Routine maintenance
in the component exceeds its strength. Stress in a
Routine maintenance of the electrical equipments goes building component could be caused by externally
alongwith the regular inspections of the equipments. applied forces, such as dead, imposed, wind or seismic
Inspections shall reveal the undue damage and excessive loads, or foundation settlement or it could be induced

46 NATIONAL BUILDING CODE OF INDIA


internally due to thermal movements, moisture d) Checking and repairing gas pipes, water pipes
changes, chemical action, etc. and plumbing services;

27.2 Cracks could be broadly classified as structural e) Re-building non-structural walls, smoke
chimneys, parapet walls, etc;
or non-structural. Structural cracks are those which are
due to incorrect design, faulty construction or f) Re-plastering of walls as required;
overloading and these may endanger the safety of a @ Rearranging disturbed roofing tiles;
building. Extensive cracking of an RCC beam is an h) Relaying cracked flooring at ground level;
instance of structural cracking. Non-structural cracks and
are mostly due to internally induced stresses in building Redecoration — whitewashing, painting, etc.
j)
materials and these generally do not directly result in
The architectural repairs as stated above do not restore
structural weakening. In course of time, however,
the original structural strength of structural components
sometime non-structural cracks may, because of
in the building and any attempt to carry out only repairs
penetration of moisture through cracks or weathering
to architectural/non-structural elements neglecting
action, result in corrosion of reinforcement and thus
the required structural repairs may have serious
may render the structure unsafe. Vertical cracks in a
implications on the safety of the building. The damage
long compound wall due to shrinkage or thermal
would be more severe in the event of the building being
movement is an instance of non-structural cracking.
shaken by the similar shock because original energy
Non-structural cracks, normally do not endanger the
absorption capacity of the building would have been
safety of a building, but may look unsightly, or may
reduced.
create an impression of faulty work or may give a
feeling of instability. In some situations, cracks may, 28.1.2 Structural Repairs
because of penetration of moisture through them, spoil
28.1.2.1 Prior to taking up of the structural repairs and
the internal finish, thus adding to cost of maintenance.
strengthening measures, it is necessary to conduct
It is, therefore, necessary to adopt measures of
detailed damage assessment to determine:
prevention or minimization of these cracks.
a) the structural condition of the building to
27.3 For complete details on causes and prevention
decide whether a structure is amendable for
of non-structural cracks, reference shall be made to repair; whether continued occupation is
good practice SP 25:1984 ‘Handbook on causes and permitted; to decide the structure as a whole
prevention of cracks in buildings’.
or a part require demolition, if considered
dangerous;
28 REPAIRS AND SEISMIC STRENGTHENING
OF BUILDINGS b) if the structure is considered amendable for
repair then detailed damage assessment of the
28.1 General Principles and Concepts individual structural components (mapping of
28.1.1 Non-structural/Architectural Repairs the crack pattern, distress location; crushed
concrete, reinforcement bendingiyielding,
28.1.1.1 The buildings affected by earthquake may etc). Non-destructive testing techniques could
suffer both non-structural and structural damages. Non- be employed to determine the residual
structural repairs may cover the damages to civil and strength of the members; and
electrical items including the services in the building.
c) to wmrk out the details of temporary supporting
Repairs to non-structural components need to be taken
arrangement of the distressed membem so that
up after the structural repairs are carried out. Care
they do not undergo further distress due to
should be taken about the connection details of
gravity loads.
architectural components to the main structural
components to ensure their stability, 28.1.2.2 After the assessment of the damage of
individual structural elements, appropriate repair
28.1.1.2 Non-structural and architectural components
methods are to be carried out componentwise
get easily affected/dislocated during the earthquake.
depending upon the extent of damage. The repair may
These repairs involve one or more of the following:
consist of the following:
a) Patching up of defects such as cracks and fall a) Removal of portions of cracked masonry
of plaster; walls and piers and rebuilding them in richer
b) Repairing doors, windows, replacement of mortar. Use of non-shrinking mortar will be
glass panes; preferable.
c) Checking and repairing electric conduitsl b) Addition of reinforcing mesh on both faces
wiring; of the cracked wall, holding it to the wall

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 47


through spikes or bolts and then covering it, generally, avoided due to a number of reasons, the main
suitably, with cement mortar or micro- ones among them being;
concrete.
a) higher cost than that of strengthening or
c) Injecting cement or epoxy like material which retrofitting,
is strong in tension, into he cracks in walls. ~
b) preservation of historical architecture, and
d) The cracked reinforced cement elements may
c) maintaining functional social and cultural
be repaired by epoxy grouting and could be
environment.
strengthened by epoxy or polymer mortar
application like shotcreting, jecketting, etc. In most instances, however, the relative cost of
retrofitting to reconstruction cost determines the
28.1.3 Seismic Strengthening
decision. As a thumb rule, if the cost of repair and
The main purpose of the seismic strengthening is to seismic strengthening is less than about 50 percent of
upgrade the seismic resistance of a damaged building the reconstruction cost, the retrofitting is adopted. This
while repairing so that it becomes safer under future may also require less working time and much less
earthquake occurrences. This work may involve some dislocation in the living style of the population. On
of the following actions: the other hand reconstruction may offer the possibility
of modernization of the habitat and may be preferred
a) Increasing the lateral strength in one or both
by well-to-do communities.
directions by increasing column and wall
areas or the number of walls and columns. 28.1.5.2 Cost-wise the building construction including
b) Giving unity to the structure, by providing a the seismic code provisions in the first instance, works
proper connection between its resisting out the cheaper in terms of its own safety and that of
elements, in such a way that inertia forces the occupants. Retrofitting an existing inadequate
generated by the vibration of the building can building may involve as much as 4 to 5 times the initial
be transmitted to the members that have the extra expenditure required on seismic resisting features.
ability to resist them. Typical important Repair and seismic strengthening of a damaged
aspects are the connections between roofs or building may even be 5 to 10 times as expensive. It is,
floors and walls, between intersecting walls therefore, very much safe as well as cost-effective to
and between walls and foundations. construct earthquake resistant buildings at the initial
c) Eliminating features that are sources of stage itself according to the relevant seismic IS codes.
weakness or that produce concentration of
28.2 For detailed guidelines for repairs and seismic
stresses in some members. Asymmetrical plan
strengthening of buildings, reference shrdl be made to
distribution of resisting members, abrupt
good practice [7(34)].
changes of stiffness from one floor to the
other, concentration of large masses and large 28.3 For detailed guidelines for improving earthquake
openings in walls without a proper peripheral resistance of low strength masonry buildings, reference
reinforcement are examples of defects of this shall be made to good practice [7(35)].
kind.
28.4 For detailed guidelines for improving earthquake
d) Avoiding the possibility of brittle modes resistance of earthen buildings, reference shall be made
of failure by proper reinforcement and to good practice [7(36)].
connection of resisting members.
28.1.4 Seismic Retrofitting SECTION 5 SAFETY IN DEMOLITION OF
BUILDINGS
Many existing buildings do not meet the seismic
strength requirements of present earthquake codes due 29 GENERAL
to original structural inadequacies and material
degradation due to time or alterations carried out during 29.1 This Section lays down the safety requirements
use over the years. Their earthquake resistance can be for carrying out demolition/dismantling work.
upgraded to the level of the present day codes by
29.2 Planning
appropriate seismic retrofitting techniques, such as
mentioned in 28.1.3. Before beginning the actual work of demolition a
careful study shall be made of the structure which is to
28.1.5 Strengthening or Retrofitting Versus
be pulled down and also of all its surroundings. This
Reconstruction
shall, in particular, include study of the manner in
28.1.5.1 Replacement of damaged buildings or which the various parts of the building to be demolished
existing unsafe buildings by reconstruction is, are supported and how far the stage by stage demolition

48 NATIONAL BUILDING CODE OF INDIA


will affect the safety of the adjoining structure. A 30.8 If a structure to be demolished has been partially
definite plan of procedure for the demolition work, wrecked by fire, explosion or other catastrophe, the
depending upon the manner in which the loads of the walls and damaged roofs shall be shored or braced
various structural parts are supported, shall be prepared suitably.
and approved by the engineer-in-charge and this shall
be followed as closely as possible, in actual execution 30.9 Protection of the Public
of the demolition work. Before the commencement of 30.9.1 Safety distances to ensure safety of the public
each stage of demolition, the foreman shall brief the shall be clearly marked and prominently sign posted.
workmen in detail regarding the safety aspects to be Every sidewalk or road adjacent to the work shall be
kept in view. closed or protected. All main roads, which are open to
It should be ensured that the demolition operations do the shall be kept open to the public! clear and
not, act any stage, endanger the safety of the adjoining unobstructed at all times. Diversions for pedestrians
buildings. Moreover, the nuisance effect of the shall be constructed, where necessary for safety.
demolishing work on the use of the adjacent buildings 30.9.2 If the structure to be demolished is more than
should be kept to the minimum. two storeyed or 7.5 m high, measured from the side
No structure or part of the structure or any floor or walk or street which can not be closed or safely
temporary support or scaffold, side wall or any device diverted, and the horizontal distance from the inside
for equipment shall be loaded in excess of the safe of the sidewalk to the structure is 4.5 m or less, a
carrying capacity, in its then existing condition. substantial sidewalk shed shall be constructed over the
entire length of the sidewalk adjacent to the structure,
30 PRECAUTIONS PRIOR TO DEMOLITION of sufficient width with a view to accommodating the
pedestrian traftlc without causing congestion. The side
30.1 On every demolition job, danger signs shall be
wrdk shed shall be lighted sufficiently to ensure safety
conspicuously posted all around the structure and all
at all times. For detailed information reference maybe
doors and openings giving access to the structure shall
made to good practice [7(37)].
be kept barricaded or manned except during the actual
passage of workmen or equipment. However, A toe board of at least 1 m high above the roof of the
provisions shall be made for at least two independent shed shall be provided on the outside edge and ends of
exits for escape of workmen during any emergent y. the sidewalk shed. Such boards may be vertical or
inclined outward at not more than 45°.
30.2 During nights, red lights shall be placed on or
about all the barricades. Except where the roof of a sidewalk shed solidly abuts
the structure, the face of the sidewalk shed towards
30.3 Where in any work of demolition it is imperative,
the building shall be completely closed by providing
because of danger existing, to ensure that no
sheating/planking to prevent falling material from
unauthorized person shall enter the site of demolition
penetrating into the shed.
outside hours; a watchman should be employed. In
addition to watching the site he shall also be responsible The roof of sidewalk sheds shall be capable of sustaining
for maintaining all notices, lights and barricades. a load of 73 N/mmz. Only in exceptional cases, say due
to lack of other space, the storing of material on a
30.4 All the necessary safety appliances shall be issued
sidewalk shed may be permitted in which case the shed
to the workers and their use explained. It shall be
shall be designed for a load of 146 N/mm2. Roof of
ensured that the workers are using all the safety
sidewalk shed shall be designed taking into account the
appliances while at work.
impact of the falling debris. By frequent removal of loads
30.5 The power on all electrical service lines shall be it shall be ensured that the,maximum load, at any time,
shut off and all such lines cut or disconnected at or on the roof of work shed is not more than 6000 N/mm2,
outside the property line, before the demolition work The height of sidewalk shed shrdl be such as to give a
is started. Prior to cutting of such lines, the necessary minimum clearance of 2.4 m.
approval shall be obtained from the electrical
Sidewrdk shed opening, for loading purposes, shall be
authorities concerned. The only exception will be any
kept closed at all time except during actual loading
power lines required for demolition work itself.
operations.
30.6 All gas, water steam and other service lines shall be
The deck flooring of the sidewalk shed shall consist
shut off and capped or otherwise controlled at or outside
of plank of not less than 50 mm in thickness closely
the building line, before demolition work is started.
laid and deck made watertight. All members of the shed
30.7 All the mains and meters of the building shall be shall be adequately bracked and connected to resist
removed or protected from damage. displacement of members or distortion of framework.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 49


30.9.3 When the horizontal distance from the inside systematically storey by storey. In the descending
of the sidewalk to the structure is more than 4.5 m order. All work in the upper floor shall be completed
and less than 7.5 m, a sidewalk shed or fence a and approved by the engineer-in-charge prior to
substantial railing shall be constructed on the inside disturbance to any supporting member on the lower
of the sidewalk or roadway along the entire length of floor. Demolition of the structure in sections maybe
the demolition side of the property with movable bars permitted in exceptional cases if proper precautions
as may be necessary for the proper prosecution of are ensured to prevent injuries to persons and damage
the work. to property.

31 PRECAUTIONS DURING DEMOLITION 33 WALLS

31.1 Prior-to commencement of work, all material of 33.1 While walls of sections of masonry are being
fragile nature like glass shall be removed. demolished, it shall be ensured that they are not allowed
to fall as single mass upon the floors of the building
31.2 All openings shall be boarded up.
that are being demolished so as to exceed the safe
31.3 Dust shall be controlled by suitable means to carrying capacity of the floors. Overloading of floors
prevent harm to workmen. shall be prevented by removing the accumulating
debris through chutes or by other means immediately.
31.4 Stacking of materials or debris shall be within
The floor shall be inspected by the engineer-in-charge
safe limits of the structural member. Additional
before undertaking demolition work and if the same is
supports, where necessary, shall be given.
found to be incapable to carry the load of the debris,
31.5 Adequate natural or artificial lighting and necessary additional precautions shall be taken so as
ventilation shall be provided for the workmen. to prevent any possible unexpected collapse of the
floor.
32 SEQUENCE OF 13EMOLlTION OPERATIONS
33.2 Walls shall be removed part by part. Stages shall
32.1 The demolition work shall be proceeded within be provided for the men to work on if the walls are
such a way that: less than one and a half brick thick and dangerous to
a) it causes the least damage and nuisance to the work by standing over them.
adjoining building and the members of the 33.3 Adequate lateral bracing shall be provided for
public, and walls which are unsound. For detailed information
b) it satisfies all safety requirements to avoid any reference may be made to good practice [7(37)].
accidents.
34 FLOORING
32.2 All existing fixtures required during demolition
operations shall be well protected with substantial 34.1 Prior to removal of masonry or concrete floor
covering to the entire satisfaction of the rules and adequate support centering shall be provided.
regulations of the undertakings or they shall be
34.2 When floors are being removed, no workmen
temporarily relocated.
shall be allowed to work in the area, directly underneath
32.3 Before demolition work is started, glazed sash, and such area shall be barricaded to prevent access to
glazed doors and windows, etc, shall be removed. All it.
fragile and loose fixtures shall be removed. The lath
34.3 Planks of sufficient strength shall be provided to
and all loose plaster shall be stripped off throughout give workmen firm support to guard against any
the entire building. This is advantageous because it unexpected floor collapse.
reduces glass breakage and also eliminates a large
amount of dust producing material before more 34.4 When floors are being removed no person shall
substantial parts of the buildings are removed. be allowed to work in an area directly underneath and
access to such area shall be barricaded.
32.4 All well openings which extend down to floor
level shall be barricaded to a height of not less than 35 DEMOLITION OF STEEL STRUCTURES
1 m above the floor level. This provision shall not apply
35.1 When a derrick is used, care shall be taken to see
to the ground level floor.
that the floor on which it is supported is amply strong
32.5 All floor openings and shafts not used for material for the loading so imposed. If necessary heavy planking
chutes shall be floored over and be enclosed with guard shall be used to distribute the load to floor beam and
rails and toe boards. girders.
32.6 The demolition shall always proceed 35.2 Overloading of equipment shall not be allowed.

50 NATIONAL BUILDING CODE OF INDIA


35.3 Tag lines shall be used on all materials being 39 DEMOLITION OF CERTAIN SPECIAL
lowered or hoisted up and a standard signal system TYPES AND ELEMENTS OF STRUCTURES
shall be used and the workmen instructed on the
39.1 Roof Trusses
signals.
If a building has a pitched roof, the structure should
35.4 No person shall be permitted to ride the load line.
be removed to wall plate level by hand methods.
35.5 No beams shall be cut until precautions have been Sufficient purlins and bracing should be retained to
taken to prevent it from swinging freely and possibly ensure stability of the remaining roof trusses while each
striking any worker or equipment to any part of the individual truss is removed progressively.
structure being demolished. 39.1.1 Temporary bracking should be added, where
35.6 All structural steel members shall be lowered necessary, to maintain stability. The end frame opposite
from the building and shall not be allowed to drop. to the end where dismantling is commenced, or
a convenient intermediate frame should be
36 CATCH PLATFORM independently and securely guyed in both directions
before work starts.
36.1 In demolition of exterior walls of multistory
structures, catch platform of sufficient strength to 39.1.2 On no account should the bottom tie of roof
prevent injuries to workers below and public shall be trusses be cut until the principal rafters are prevented
provided, when the external walls are more than 20 m from making out ward movement.
in height.
39.1.3 Adequate hoisting gears suitable for the loads
36.2 Such catch platform shall be constructed and shall be provided. If during demolition any thing is to
maintained not more than 3 storeys below the storey be put on the floor below the level of the truss, it shall
from which exterior wall is being demolished. be ensured that the floor is capable of taking the load.
When demolition has progressed to within 3 storeys 39.2 Heavy Floor Beams
of ground level, catch platform will not be considered
necessary. Heavy baulks of timber and steel beams should be
supported before cutting at the extremities and should
36.3 Catch platform shall be capable of sustaining a then be lowered gently to a safe working place.
live load of not less than 6100 N/mz.
39.3 Jack Arches
36.4 Materials shall not be dumped on the catch
platform nor shall they be used for storage of materials. Where tie rods are present between main supporting
beams, these should not be cut until after the arch or
37 STAIRS, PASSAGEWAYS AND LADDERS series of arches in the floor have been removed. The
floor should be demolished in strips parallel to the span
37.1 Stairs with railings, passageways and ladders
shall be left in place as long as possible and maintained of the arch rings (at right angles to the main floor
in a safe condition. beams).

39.4 Brick Arches


37.2 All ladders shall be secured against, slipping out
at the bottom and against movement in any direction Expert advice should be obtained and, at all stages of
at the top. the demolition, the closet supervision should be given
by persons fully experienced and conversant in the type
38 MECHANICAL DEMOLITION
of work to ensure that the structure is stable at all times.
When demolition is to be performed by mechanical
However, the following points may be kept in view.
devices, such as weight ball and power shovels, the
following additional precautions may be observed: 39.4.1 On no account should the restraining influence
of the abutments be removed before the dead load of
a) The area shall be barricaded for a minimum
the spandrel fill and the arch rings are removed.
distance of 1% times the height of the wall,
b) While the mechanical device is in operation, 39.4.2 A single span arch can be demolished by hand
no workmen shall be allowed to enter the by cutting narrow segments progressively from each
building being demolished, springing parallel to the span of the arch, until the width
c) The device shall be so located as to avoid of the arch has been reduced to a minimum which can
falling debris, and then be collapsed.

d) The mechanical device when being used shall 39.4.3 Where deliberate collapse is feasible, the crown
not cause any damage to adjacent structure, may be broken by the demolition brdl method working
power line, etc. progressively from edges to the centre.

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 51


39.4.4 Collapse of the structure can be effected in one and whenever necessary temporary supports shall be
action by the use of explosives. Charges should be provided.
inserted into bore holes drilled in both arch and
39.8 Prestressed Reinforced Concrete
abutments.
Before commencing of the demolition work, advice
39.4.5 In multi-span arches, before individual arches
of an engineering expert in such demolition shall be
are removed, lateral restraint should be provided at the
obtained and followed.
springing level. Demolition may then proceed as for
single span; where explosives are used it is preferable 40 LOWERING, REMOVAL AND DISPOSAL
to ensure the collapse of the whole structure in one OF MATERIALS
operation to obviate the chance of leaving unstable
portion standing. 40.1 Dismantled materials may be thrown to the
ground only after taking adequate precautions. The
39.5 Cantilever (Not Part of a Framed Structure) material shall preferably be dumped inside the building.
Canopies, cornices, staircases and balconies should be Normally such materials shall be lowered to the ground
demolished or supported before tailing down load is or to the top of the sidewalk shed where provided by
removed. means of ropes or suitable tackles.

39.6 In-situ Reinforced Concrete 40.2 Through Chutes

Before commencing demolition, the nature and 40.2.1 Wooden or metal chutes maybe provided from
condition of the concrete, the condition and position removal of materials. The chutes shall preferably be
of reinforcement, and the possibility of lack of provided at the centre of the building for efficient
continuity of reinforcement should be ascertained. disposal of debris.

Demolition should be commenced by removing 40.2.2 Chutes, if provided at an angle of more than
partitions and external non-load bearing cladding. 45° from the horizontal, shall be entirely enclosed on
all the four sides, except for opening at or about the
39.6.1 Reinforced Concrete Beams floor level for receiving the materials.
A supporting rope should be attached to the beam. 40.2.3 To prevent the descending material attaining a
Then the concrete should be removed from both ends dangerous speed, chute shall not extend in an unbroken
by pneumatic drill and the reinforcement exposed. line for more than two storeys. A gate or stop shall be
The reinforcement should then be cut in such a way provided with suitable means for closing at the bottom
as to allow the beam to be lowered under control to of each chute to stop the flow of materials.
the floor.
40.2.4 Any opening into which workmen dump debris
39.6.2 Reinforced Concrete Columns at the top of chute shall be guarded by a substantial
The reinforcement should be exposed at the base after guard rail extending at least 1 m above the level of the
restraining wire guy ropes have been placed round the floor or other surface on which men stand to dump the
member at the top. The reinforcement should then be materials into the chute.
out in such a way as to allow it to be pulled down to 40.2.5 A toe board or bumper, not less than 50 mm
the floor under control. thick and 150 mm high shall be provided at each chute
39.6.3 Reinforced Concrete Walls openings, if the material is dumped from the wheel
barrows. Any space between the chute and the edge of
These should be cut into strips and demolished as for the opening in the floor ~ough which it passes shall
columns. be solidly planked over.
39.6.4 Suspended Floors and Roofs
40.3 Through Holes in the Floors
The slab should be cut into strips parallel to the main
40.3.1 Debris may also be dropped through holes in
reinforcement and demolished strip by strip. Where
the floor without the use of chutes, In such a case the
ribbed construction has been used, the principle of
total area of the hole cut in any intermediate floor, one
design and method of construction should be
which lies between floor that is being demolished and
determined before demolition is commenced. Care
the storage floor shall not exceed 25 percent of such
should be taken not to cut the ribs inadvertently.
floor area. It shall be ensured that the storage floor is
39.7 Precast Reinforced Concrete of adequate strength to withstand the impact of the
falling material.
Due precautions shall be taken to avoid toppling over
of prefabricated units or any other part of the structure 40.3.2 All intermediate floor openings for passage of

52 NATIONAL BUILDING CODE OF INDIA


materials shall be completely enclosed with barricades d) The debris should fwst be removed from
or guard rails not less than 1 m high and at a distance top. Early removal from bottom or sides
of not less than 1 m from the edge of general opening. of dump may cause collapse of debris,
No barricades or guard rails shall be removed until causing injuries.
the storey immediately above has been demolished
down to the floor line and all debris cleared from the 41 MISCELLANEOUS
floor. 41.1 No demolition work should be carried out during
40.3.3 When the cutting of a hole in an intermediate night as far as possible, especially when the structure
floor between the storage floor and the floor which is to be demolished is in an inhabited area. If such night
being demolished makes the intermediate floor or any work has to be done, additional precautions by way of
portion of it unsafe, then such intermediate floor shall additional red warning signals, working lights and
be properly shored. It shall also be ensured that the watchmen, shall be provided to avoid any injury to
supporting walls are not kept without adequate lateral workmen and public. Demolition work shrdl not be
restraints. carried out during storm and heavy rain.

40.4 Removal of Materials 41.2 Warning devices shall be installed in the area to
warn the workers in case of any danger.
40.4.1 As demolition work proceeds, the released
serviceable materials of different types shall be 41.3 Safety devices like industrial safety helmets
separated from the unserviceable lot (hereinafter called conforming to the accepted standards [7(9)] and
‘MALBA’) at suitable time intervals and properly goggles made of celluloid lens, shall be issued to the
stocked clear of the spots where demolition work is workmen. Foreman-in-charge of the work areas shall
being done. ensure that all the workmen are wearing the safety
devices before commencing any work.
40.4.2 The MALBA obtained during demolition shall
be collected in well-formed heaps at properly selected 41.4 Construction sheds and tool boxes shall be so
places, keeping in view safe conditions for workmen located as to protect workers from injuries from the
in the area. The height of each MALBA heap shall be falling debris.
limited to ensure its toppling over or otherwise 41.5 Where there is a likelihood of injuries to hands
endangering the safety of workmen or passersby. of workmen when demolishing RCC, steel structures,
40.4.3 The MALBA shall be removed from the etc, gloves of suitable materials shall be worn by
demolition site to a location as required by the local workmen.
civil authority. Depending on the space available at the 41.6 Sufficient protection by way of both overhead
demolition site, this operation of conveying MALBA to cover and screens shall be provided to prevent injuries
its final disposal location may have to be carried out a to the workmen and the public.
number of times during the demolition work. In any
case, the demolition work shall not be considered as 41.7 Safety belts or ropes shall be used by workmen
completed and the area declared fit for further occupation when working at higher levels.
till all the MALBA has been carried to its final disposal 41.8 Grading of Plot
location and the demolition areas tidied up.
When a building has been demolished and no building
40.4.4 Materials which are likely to cause dust operation has been projected or approved, the vacant
nuisance or undue environmental pollution in any other plot shall be filled, graded and maintained in
way, shall be removed from the site at the earliest and conformity to the establish~ street grades at curb level.
till then they shall be suitable covered. Such materials The plot shall be mai~tained free from the
shall be covered during transportation also. accumulation of rubbish and all other unsafe and
40.4.5 a) Glass and steel should be dumped or hazardous conditions which endangers the life or health
buried separately to prevent injury. of the public; and provisions shall be made to
prevent the accumulation of water or damage to any
b) Workman should be provided with
foundations on the premises or the adjoining property.
suitable protective gears for personal
safety during works, lie safety helmets, 42 FIRST-AID
boots, hand gloves, goggles, special
attire, etc. 42.1 A copy of all pertinent regulations and notices
concerning accidents, injury and first-aid shall be
c) The work of removal of debris should be
prominently exhibited at the work site.
carried out during day. In case of poor
visibility artificial light may be provided. 42.2 Depending on the scope and nature of the work,

PART 7 CONSTRUCTIONAL PRACTICES AND SAFETY 53


a person, qualified in first-aid shall be available at work telephone may be provided to first-aid assistant with
site to render and direct first-aid to casualties. He shall telephone numbers of the hospitals prominently
maintain a list of individuals qualified to serve in first- displayed.
aid work. Enough first-aid kit, including a stretcher Complete reports of all accidents and action taken
and cot with accessories shall be provided at site. A thereon shall be forwarded to the competent authorities.

ANNEX A

(Clause 2.1.2)

PROGRAMME EVALUATION AND REVIEW TECHNIQUE, AND


CRITICAL PATH METHOD

A-O INTRODUCTION cement, stone and timbe~ and plants, such as


concrete mixer, vibrators, water pump for
A-O.1 Programme Evaluation and Review Technique
curing.
(PERT) and Critical Path Method (CPM) are modern
e) Soil explorations and trial pits.
management tools or devices, which have made it
possible to achieve considerable savings in cost and f) Excavation in foundations, including
time of construction. They can be used with advantage demolition, if needed.
for demolition, constructional safety and fire protection g)l) Construction safety aspects specially in case
measures, by including them in the list of activities of pile foundations.
(also called events) along-side with other ‘events’ of h)l) Blasting if required (for deep foundations).
the project. j)l) Fire protection measures.

A-O.2 Advance Planning A-1.2 Time Needed for Each Activity

A-O.2.1 PERT and CPM enable us to achieve judicious An assessment is to be made to find out the time needed
employment and utilization of resources, such as for each activity and then to list out those activities,
labour, materials, and equipment by pre-determining which can be executed concurrently (or simultaneously)
the various stages, listing out the various activities and with each other. For example, while designing of the
drawing out ‘Arrow Network Diagram’. building is in hand, correspondence for land purchase
can also go on side by side; or while work in
A-O.3 Synchronization of Sub-Projects foundations is in progress, order for ‘joinery’ can be
placed.
A-O.3.1 Another extremely important advantage of
CPM is that various factors influencing completion of A-1.3 Critical Activity
a project can be scientifically planned to be coordinated
It should then be seen as to which of the activities are
such that the completion of various sub-projects and
critical, that is which items are such that a single day’s
services, such as furniture, sewage, electricity and delay will mean overall delay on the project. Contrary
water supply synchronises. to this, it will be seen from CPM Network that certain
activities can be delayed to a certain extent without
A-1 PREPARATION OF CPM CHART (LISTING
delaying the completion of the project. This is a very
OUT THE ACTIVITIES)
useful and valuable i~ormation for the ‘Project
A-1.l The most important step in preparation of CPM Manager’. That is where resources scheduling becomes
network is to list out the activities involved to the easier and economical and a time saver. It eliminates
minutest details. For example, a few activities in case chances of idle labour and higher expenses which are
of a building project are given below: results of haphazard planning.

a) Planning and designing of building by A-2 UPDATING


architect, engineer and approvrd of plans by
the Authority. A-2.1 In implementing the CPM, there could be gaps
between the planned CPM and actual progress
b) Making the land available.
c) Outlining detailed specifications. 1)These can be further sub-divided and number of activities
d) Procurement of materials, such as sand, increased.

54 NATIONALBUILDING CODE OF INDIA


or position on ground. This should be checked for the owners, or departments, it is recommended that
periodically-weekly, fortnightly or monthly depending it should be an essential condition of the contract to
on nature and size of project. submit a CPM Chart along with the quoted tenders.
This will ensure that the construction work will be
A-3 GENERAL
according to a systematic, engineer-like and well-knit
A-3.1 In case of projects being executed by contractors plan of execution.

ANNEX B

(Clause 4.1)

CHECK LIST FOR STACKING AND STORAGE OF MATERIALS

sl Material/Component Base Stack Type of Cover


No. ~~ ~
Firm Hard Off- Heaps Tiers Flat Vertical Open Open Under
Level ~oor Floor but shed
Ground covered
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12)
1. Cement
2. Lime
a) Quick lime
b) Hydrated lime
3. Stones and Aggregates
a) Stones, aggregates, fly ash
and cinder
b) Veneering stones
4. Bricks and Blocks
5. Tiles
a) Clay and concrete floor,
wall and roof tiles
b) Ceramic tiles v’
6. Partially Pre-fabricated Wall
and Roof Components
a) RC planks, prefabricated
brick panels and ferro-
cement panels
b) Channel units, cored units
and L-Panels
c) Waffle units, RC joists,
single tee and double tee
7. Timber 4
8. Steel
9. Aluminium Sections
10. Doors, Windows and
Ventilators
11. Roofing Sheets
a) AC
b) GI and Aluminium sheets
c) Plastic sheets

PART 7 CONSTRUCTIONALPRACTICES ANDSAFETY 55


‘m

ANNEX B — Continued

(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12)
12. Boards like Plywood,
Particle Boards, Fibre I/
Boards, Blackboards and
Gypsum Board
13. Plastic and Rubber Flooring
a) Sheets in rolls
b) Tiles
14. Glass Sheets
15. Glass Bricks/Blocks
16. CI, GI and AC Pipes and
Fittings
a) Pipes
b) CI and GI Fittings
c) AC Fittings
17. Polyethylene Pipes
18. Unplasticized PVC Pipes ---
19. Bitumen, Road Tar,
Asphalt, etc in Drums
20. Oil Paints
21. Sanitary Appliances

ANNEX C

(Clause 26.3.2.2.2)
COMMON CAUSES FOR MAINTENANCE PROBLEMS

C-O MAJOR CAUSES FOR MAINTENANCE Worn out felts.


PROBLEMS Bubbling up of tarfelt and separation of
C-1 FLOORS joints.
Leakage from the openings provided on the
a) Poor quality of construction which includes
roof.
quality of construction material and
workmanship. C-3 PLUMBING
b) Improper slopes, mainly in kitchen, bathrooms/
a) Inadequate slopes in soillwaste pipes.
toilets etc.
b) Improper lead joints.
c) Lack of rounding at junctions of walls with
c) Joints in walls. ,
floors.
d) Improper junctions of stacks.
d) Lack of dampproof course treatment in walls
and particularly in sunken floors. e) Inadequate cleaning eyes at junctions.

e) Poor design of building. f) Inadequate slopes in sewage pipes.


g) Throwing of solid wastes in WC’S.
C-2 ROOFS
h) Lack of periodical checking and cleaning.
a) Inadequate roof slopes. Lack of motivation/education to users for
j)
b) Inferior quality of construction. proper use.
c) Cracks on roof surfaces. k) Overflow from service tanks.
d) Inadequate provision of rain water spouts. m) Inferior quality of fittings and fixtures.
e) Blockages in gratings/rain water pipes. n) Inadequate design.

56 NATIONALBUILDING CODE OF LNDIA


C-4 DRAINAGE g) Throwing of solid waste in the open surface
drains.
a) Improper surface dressing around buildings
and improper upkeep of surroundings. C-5 ELECTRICAL
b) Growth of wild grass and vegetation.
a) Loose connections.
c) Inadequate drainage system around the
building. b) Improper earthing and earth connections.
d) Inadequate slope of the drains or drainage c) Damages to wires, cables and other
pipes. installations.
e) Inadequate number of inspection chambers. d) Under rated cables/wires and other
f) Theft of manhole covers etc. installations.

ANNEX D

(Clause 26.6.5)

FORMAT FOR INSPECTION REPORT


Date: .......................... ... ............... .
Buildin@310ck : ................... .... ............ ..........
.................. ............ .. .......... ...

Condition

Sound Suspect Defective

FLOORS & STAIRCASES

Ground Floor
Finish
Skirting
Structure
Damp-proofing
Ceiling
Under floors, spaces, (Suspended floors)
Termites/insects

Upper Floors
Finish
Structure
Ceiling
Suspended ceiling

Stair cases
Structure
Treads
Finishes
Balustrade
Soffits
Finish

ROOFING

Flat/Pitched
Finish
Insulation
Structure

PART 7 CONSTRUCTIONALPRACTICES ANDSAFETY 57


ANNEX D — Continued
-.. .
Conditwn

Sound SISpect Defective

Roof lights/glazing
Parapets
Cutters
Rain Water Pipes
hhd Phuska
Roof interiors (Pitched)
Growth of vegetation

SANITARY INSTALLATIONS

Plumbing
Fittings/Pipings, WC’s
Taps
Sinks
Basins
Urinals
Cisterns
Geysers

Sewage Disposal
Soil pipes
Manholes
Sewerlines

Drainage
Gully chambers
Sewers
Surface drains
Inspection chambers
Structural movement
Failure of material
Design or construction defects
Overhead Tanks/Underground
Sumpsflerrace Tanks
Septic Tanks

Remarks

(Clause 26.7.3.2)

GUIDELINES FOR MAINTENANCE OF ELECTRICAL EQUIPMENTS

E-1 In case of electrical appliances, manufacturer’s be available with the maintenance unit. Following
instructions for the usage and maintenance of the records should be available.
equipment should be strictly followed. a) Manufacturer’s name
E-2 The detailed/working drawings of all the b) Nameplate of the equipment and its sailent
components of electrical installations should always features such as capacity, rating etc.

58 NATIONALWILDING CODE OF INDIA


c) Manufacturer’s recommendations regarding E-12 The standby system for tripping and closing
availability/usage of spare parts. supplies should always be kept in good order.
d) Manufacturer’s recommendations for Indicators and alarms should be maintained in time
periodical maintenance and post fault with the manufacturer’s instructions.
maintenance.
E-13 Tools, spares and instruments should be stored
e) Details of the maintenance operations near to the installation. These should be regularly
performed in the past. checked against an inventory.
E-3 Care should be taken while selecting replacement E-14 Before the start of maintenance of the circuit
parts. The spare parts should be correct and suitable, switches it should be ensured that all incoming and
preferably as recommended by the manufacturer of the outgoing main auxiliary circuits are dead and remain
installation. During the placement of order for the so during the maintenance. Overheating of the circuit
supply of spare parts, nameplate particulars and serial switches is the root cause for faults. Overheating may
number should be quoted. be caused by inadequate ventilation, overloading,
E-4 The space where the equipment is kept should be loose connection, insufficient contact force and
clean and properly ventilated. Equipment should not malalignment.
be disturbed needlessly. Before cleaning, the
E-15 Some circuit breakers are not intended to be
equipment should be made dead. For internal cleaning
maintained, such as miniature circuit breakers (MCBS).
a section cleaner should be used.
Such items should not be dismantled for maintenance.
E-5 Covers and doors should not be left open These should be renewed periodically.
unnecessarily during maintenance. Afterwards they
E-16 For the maintenance of fuses periodical
should be promptly and correctly closed and locked.
inspection should be done for correct rating, security,
E-6 Before removing the covers and connections, all overheating and correct location/orientation. Element
covers and cable terminations should be marked to of renewable fuses should be renewed when the
ensure correct replacements. Disturbed connections deterioration is apparent. The availability and correct
and temporary connections should be marked to replacement of fuse links should be ensured.
facilitate re-connection. Temporary connections and
E-17 If a fuse link of certain rating has failed and is
markings should be removed before the installation is
replaced, then all fuse-links of same rating apparently
put to use.
subjected to the fault should be destroyed and replaced
E-7 Those connections which have not been disturbed by new fuse links.
should also be checked for soundness and overheating.
E-18 In order to be reasonably sure that circuit breaker
E-8 All insulations should be regularly checked. Solid is capable of operation when required, these should be
insulations should be checked for cracks and other tripped and reclosed at regular intervals. Tripping
defects. Fibrous and organic insulations should be should be proved manually and where possible
checked for sign of blistering, delamination and electrically via the protective relay contacts. The
mechanical damage. For insulating oils the interval leakage of oil, sign of corrosion, and any unusual smell
between tests should be carried out as per the which may indicate over-heating should be detected
recommendations of the manufacturer and keeping the through inspections.
adverse environmental conditions in mind.
E-19 Timing devices are mostly designed for specialist
E-9 It should be ensured that the earthing connections maintenance. These should not be dismantled for
are sound and all contact screws are tight. maintenance or overhaul purposes unless specifically
recommended by the manufacturers’. Actual timing
E-10 During the examination of interlocks it is
periods should be verified with set values and
necessary to take precautions to prevent danger to plant
application requirements.
or persons in the event of malfunction or inadvertent
operation. A person responsible for checking and E-20 In case of cable boxes and terminations, security
maintaining any interlock system should have thorough of mounting and earthing should be examined. Exposed
knowledge of the extent, nature and function of the tails should be inspected for good conditions of
interlock. insulation and freedom from moisture.

E-n If the equipment is ventilated then it should be E-21 Battery cells should be inspected for shedding
ensured that the airflow is smooth and not restricted. of active material, sedimentation and buckling of
If filters are provided, they should be cleaned or plates. Level of electrolyte should be regularly checked
replaced as necessary. and the level should be corrected with distilled water.

PART 7 CONSTRUCTIONALPRACTICES ANDSAFETY 59


y--

LIST OF STANDARDS

The following list records those standards which are 1S No. Title
acceptable as ‘good practice’ and ‘accepted standards’ (Part 3): 1992 Foundations for rotary type
in the fulfillment of the requirements of the Code. The machines (medium and
latest version of a standard shall be adopted at the time high frequency) (second
of enforcement of the Code. The standards listed may revision)
be used by the Authority as a guide in conformance
(Part 4): 1979 Foundations for rotary type
with the requirements of the referred clauses in the
machines of low frequency
Code,
(first revision)
IS No. Title
(Part 5): 1987 Foundations for impact
(1) a) Fowzdadom machines other than
1080:1985 Code of practice for design hammers forging and
and construction of shallow stamping press pig breakers
foundations on soils (other (drop crusher and jolter)
than raft, ring and shell) (first revision)
(second revision) 9456:1980 Code of practice for design
1904:1986 Code of practice for design and construction of conical
and construction of and hyperbolic paraboidal
foundations in soils: types of shell foundations
General requirements 9556:1980 Code of practice for design
(third revision) and construction of
2911 Code of practice for design diaphragm walls
and construction of pile 13094:1992 Guidelines for selection of
foundations ground improvement
(Part 1L33C1) :1979 Concrete piles, Section 1 t&hniques for foundation
Driven cast in-situ concrete in weak soils
piles (@t revision) 15284 Design and construction
(Part l/See 2): 1979 Concrete piles, Section 2 (Part 1): 2003 for ground improvement:
Board cast in-situ piles Part 1 Stone columns
(jirst revision) b) Masorvy
(Part l/See 3): 1979 Concrete piles, Section 3 Code of practice for
1597
Driven precast concrete construction of stone
piles (/irst revision) masonry
(Part l/See 4): 1984 Concrete piles, Section 4 (Part 1): 1992 Rubble stone masonry (first
Bored precast concrete revision)
piles (first revision)
(Part 2) :1992 Ashlar masonry (first
(Part 2): 1980 Timber piles (@t revision) revision)
(Part 3): 1980 Under-reamed piles (first 2110:1980 Code of practice for in-situ
revision) construction of walls in
(Part 4): 1985 Load test on piles (first ,0buildings with soil-cement
revision) (first revision)
2974 Code of practice for design 2212:1991 Code of practice for
and construction of machine brickwork (first revision)
foundations 2250:1981 Code of practice for
(Part 1): 1982 Foundations for recipro- preparation and use of
cating type machines masonry mortars (first
(second revision) revision)
(Part 2): 1980 Foundations for impact 2572:1963 Code of practice for
type machines (hammer construction of hollow
foundations) (first revision) concrete block masonry

60 NATIONALBUILDINGCODE OF INDIA
1S No. Title IS No. Title

3630:1992 Code of practice for 12506:1988 Code of practice for


construction of non-load improved thatching of roof
bearing gypsum block with wrought and fire
partitions (jirst revision) retardant treatment
4407:1967 Code of practice for reed d) Concrete
walling
456:2000 Code of practice for plain
4441:1980 Code of practice for use of and reinforced concrete
silicate type chemical ~ourth revision)
resistant mortars (first
457:1957 Code of practice for general
revision) construction of plain and
4442:1980 Code of practice for use of reinforced concrete for
sulphur type chemical dams and other massive
resistant mortars (first structures
revision) 2502:1963 Code of practice for
4443:1980 Code of practice for use of bending and fixing of bars
resin type chemical for concrete reinforcement
resistant mortars (first 2541:1991 Code of practice for
revision) preparation and use of lime
6041:1985 Code of practice for concrete. (second revision)
construction of autoclave 3370 Code of practice for
cellular concrete block concrete structures for the
masonry (jfrst revision) storage of liquids
6042:1969 Code of practice for (Part 1): 1965 General requirements
constructionof lightweight (Part 2): 1965 Reinforced concrete
concrete block masonry structures
(first revision) concrete
(Part 3): 1967 Prestressed
c) Timber and Bamboo structures
3558:1983 Code of practice for use of
1634:1992 Code of practice for design
immersion vibrators for
and constructions of wood
consolidating concrete
stair for houses (second
(first revision)
revision)
5817:1992 Code of practice for
2366:1983 Code of practice for nail-
preparation and use of lime
jointed timber construction
pozzolana mixture concrete
@-st revision)
in buildings and roads (jrst
3670:1989 Code of practice for revision)
construction of timber 7246:1974 Recommendations for use
floors (first revision) of table vibrators for
4913:1968 Code of practice for consolidating concrete
selection, installation and 7861 code of practice for
maintenance of timber extreme whether concreting
doors and windows
(Part 1): 1975 Recommended practice for
4983:1984 Code of practice for design hot weather concreting
and construction of nail (Part 2): 1981 Recommended practice for
laminated timber beams cold weather concreting
5390:1984 Code of practice for 10262:1982 Recommended guidelines
construction of timber for concrete mix design
ceilings (jlrst revision)
10359:1982 Code of practice for
11096:1984 Code of practice for design manufacture and use of
and construction of bolt- lime pozzolana concrete
jointed timber construction blocks for paving

PART 7 CONSTRUCTIONALPRACTICES ANDSAFETY 61


IS No. Title IS No. Title
14687:1999 Guidelines for falsework 1197:1970 Code of practice for laying
for concrete structures of rubber floors (first
e) Steel revision)
1198:1982 Code of practice for laying,
800:1984 Code of practice for general
fixing and maintenance of
steel construction (second
linoleum floor (first
revision)
revision)
801:1975 Code of practice for use of
1443:1972 Code of practice for laying
cold formed light gauge
steel structural members and finishing of cement
in general building concrete flooring tiles (@t
construction (@revision) revision)

805:1968 Code of practice for use 2118:1980 Code of practice for


of steel in gravity water construction of jack-arch
tanks type of building floor or
806:1968 Code of practice for use roof @rst revision)
of steel tubes in general 2119:1980 Code of practice for
building construction (first construction of brick-cwn-
revision) concrete composite (Madras
4000:1992 Code of practice for high terrace) floo; or roof (first
strength bolts in steel revision)
structures (first revision) 2204:1962 Code of practice for
4180:1967 Code of practice for construction of reinforced
corrosion protection of concrete shell roof
light gauge steel sections
2571:1970 Code of practice for laying
used in building
in-situ cement concrete
6533 Code of practice for design flooring (@@ revision)
and construction of steel
2700:1987 Code of practice for
chimneys
roofing with wooden
(Part 1): 1989 Mechanical aspects (first shingles @w revision)
revision)
2792:1964 Code of practice for design
(Part 2): 1989 Structural aspects (first
and construction of stone
revision)
slab over joist floor
8629 Code of practice for
2858:1984 Code of practice for
(Parts 1 to 3) :1977 protection of iron and steel
roofing with Mangalore
structures from atmospheric
tiles (jirst revision)
corrosion
9077:1979 Code of practice of 3007 Code of practice for laying
corrosion protection of of asbestos cement sheets:
steel reinforcement in RB (Part 1): 1999 Corrugated sheets (first
and RCC construction revision)
9172:1979 Recommended design (Part 2): 1999 Semi-corrugated sheets
practice for corrosion (first revision)
prevention of steel structures
3670:1989 Code of practice for
f) Flooring and Roofing construction of timber
floors (jlrst revision)
658:1982 Code of practice for
magnesium oxychloride 5119 Code of practice for laying
composition floors (second (Part 1): 1968 and fixing of sloped roof
revision) coverings: Part 1 Slating

1196:1978 Code of practice for laying 5318:1969 Code of practice for laying
bitumen mastic flooring of flexible PVC sheet and
(second revision) tile flooring

62 NATIONALBUILDING CODE OF INDIA


IsNo. Title IS NO. Title
5389:1969 Code of practice for laying (Part 1): 1971 Pretreatment (/irst revision)
of hardwood parquet and (Part 2): 1971 Painting (jirst revision)
woodblockfloors
IS 1609:1991 Code of practice for laying
5390:1984 Code of practice for damp-proofing treatment
construction of timber using bitumen felts (second
ceilings (first revision) revision)
5766:1970 Code of practice for laying 1661:1972 Code of practice for
burnt clay brick flooring application of cement and
6061 Code of practice for cement lime plaster finishes
construction of floor and (first revision)
roof with joists and filler Code of practice for laying
2114:1984
blocks
in-situ terrazzo floor finish
(Part 1) :1971 With hollow concrete filler (jirst revision)
blocks
2115:1980 Code of practice for flat-
(Part 2): 1981 With hollow clay filler roof finish: Mud PHUSKA
blocks (jirst revision) (second revision)
(Part 3): 1981 Precast hollow clay blocks 2338 Code of practice for
joists and hollow clay filler finishing of wood and
blocks wood based materials
(Part 4): 1981 With precast hollow clay (Part 1): 1967 (@EtiOllS and workmmhip
block slab panels
(Part 2): 1967 Schedules
6332:1984 Code of practice for
2394:1984 .Code of practice for
construction of floors and
application of lime plaster
roofs using precast doubly-
finish (fb-st revision)
curved shell units (first
revision) 2395 Code of practice for
painting concrete, masonry
9472:1980 Code of practice for laying
and plaster surfaces
mosaic parquet flooring
10297:1982 Code of practice for design (Part 1): 1994 @@iOIIS and wdmanship
and construction of floors (/irst revision)
and roofs using precast (Part 2): 1994 Schedule @rst revision)
reinforce d/prestressed 2402:1963 Code of practice for
concrete ribbed or cored external rendered finishes
slab units
2441:1984 Code of practice for fixing
10440:1983 Code of practice for ceiling covering (first
construction of reinforced revision)
brick and RBC floors and
2524 Code of practice for
roofs
painting of non-ferrous
10505:1983 Code of practice for
metals in buildings:
construction of floors and
roofs using precast (Part 1): 1968 Pre-treatment
concrete waffle units (Part 2): 1968 Painting
g) Finishes 3036:1992 Code of practice for laying
1346:1991 Code of practice for lime concrete for a water-
waterproofing of roofs with proofed roof finish (second
bitumen felts (third revision) revision)
1414:1989 Code of practice for fixing 3067:1988 Code of practice for general
wall coverings design details and
1477 Code of practice for preparatory work for darnp-
painting of ferrous metals proofing and waterproofing
in buildings of buildings (first revision)

PART 7 CONSTRUCTIONALPR4CTICES ANDSAFETY 63


,~”””y-’-

1S No. Title IS No. Title


3140:1965 Code of practice for 3114:1994 Code of practice for laying
painting asbestos cement of cast iron pipes (second
building products revision)
3548:1988 Code of practice for glazing 4127:1983 Code of practice for laying
in building (first revision) of glazed stoneware pipes
4101 Code of practice for (jirst revision)
external facing and 5329:1983 Code of practice for sanitary
veneers: pipe work above ground for
(Part 1): 1967 Stone facing buildings (first revision)
(Part 2): 1967 Cement concrete facing 5822:1994 Code of practice for laying
of welded steel pipes
(Part 3): 1985 wall tiling and mosaics
for water supply (second
(jirst revision)
revision)
4365:1967 Code of practice for
6530:1972 Code of practice for laying
application of bitumen
of asbestos cement pressure
mastic for waterproofing of
pipes
roofs
7634 Code of practice for plastics
4597:1968 Code of practice for
pipe work for portable
finishing of wood and
water supplies: .
wood based products with
nitrocellulose and cold (Part 1): 1975 Choice of materials and
catalysed materials general recommendations
4631: 986 Code of practice for laying (Part 2): 1975 Laying and jointing
of epoxy resin floor polyethylene (PE) pipes
toppings (first revision) (Part 3): 2003 Laying and jointing of
5491: 969 Code of practice for laying unplasticized PVC pipes
in-situ granolithic concrete j) Measurements
floor topping
1200 Method of measurement
6278:1971 Code of practice for white-
of building and civil
washing and colonr washing
engineering works:
6494:1988 Code of practice for water
(Part 1): 1992 Earthwork (@rth revision)
proofing of underground
water reservoirs and (Part 2): 1974 Concrete work (third
swimming pools ~irst revision)
revision) (Part 3): 1976 Brickwork (third revision)
7198:1974 Code of practice for damp- (Part 4)1976 Stone masonry (third
proofing using bitumen revision)
mastic (Part 5): 1982 Forrnwork (third revision)
7290:1979 Recommendations for use (Part 6): 1974 Refactory work (second
of polyethylene film for revision)
waterproofing of roofs (Part 7): 1972 ,,Hardware (second revision)
(@st revision)
(Part 8): 1993 Steel work and iron work
9918:1981 Code of practice for in-situ ~ourth revision)
waterproofing and damp-
(Part 9): 1973 Roof covering (including
proofing treatments with
cladding) (second revision)
glass fibre tissue reinforced
(Part 10) :1973 Ceiling and linings (second
bitumen
revision)
h) Piping
(Part 11) :1977 Paving, floor finishes dado
783:1985 Code of practice for laying and skirting (third revision)
of concrete pipes (first (Part 12) :1976 Plastering and pointing
revision) (third revision)

64 NATIONALBUILDINGCODE OF INDIA
IS No. Title IS No. Title
(Part 13) :1994 White washing, colour 2527:1984 Code of practice for fixing
washing, distempering and rain-water gutters and
painting of building down pipes for roof
surfaces ($jlh revision) drainage (first revision)
(Part 14) :1984 Glazing (third revision) 3414:1968 Code of practice for design
(Part 15) :1987 Paining, polishing, and installation of joints in
varnishing, etc (fourth buildings
revision) 3548:1988 Code of practice for glazing
(Part 16) :1979 Laying of water and sewer in buildings @t revision)
lines including appurtenant 3558:1983 Code of practice for use of
items (third revision) immersion vibrators for
(Part 17) :1985 Roadwork including air consolidating concrete
field pavements (third (first revision)
revision) 3935:1966 Code of practice for
(Part 18) :1974 Demolition and dismantling composite construction
(third revision) 4326:1993 Code of practice for
(Part 19) :1981 Water supply, plumbing earthquake resistant design
and drains (third revision) and construction of
buildings (second revision)
(Part 20) :1981 Laying of gas and oil pipe
lines (third revision) 4913:1968 Code of practice for
selection, installation and
(Part 21):1973 Woodwork and joinery
maintenance of timber
(second revision)
doors and windows
(Part 23) :1988 Piling ~ourth revision)
6313 Code of practice for anti-
(Part 24) :1983 Well foundations (third termite measures in
revision) buildings:
3861:2002 Method of measurement of (Part 1): 1981 Constructional measures
plinth, carpet and rentable @-st revision)
areas of buildings (second
(Part 2): 2001 Pre-constructional chemical
revision)
treatment measures (second
k) Others revision)
1081:1960 Code of practice for fixing (Part 3): 2001 Treatment for existing
and glazing of metal (steel buildings (second revision)
and aluminium) doors, 6924:1973 Code of practice for the
windows and ventilators construction of refuse
1649:1962 Code of practice for design chutes in multistoreyed
and construction of flues buildings
and chimneys for domestic 7246:1974 Recommendation for use
heating appliances of table vibrators for
1946:1961 Code of practice for use of ‘consolidating concrete
fixing devices in walls, 8147:1976 Code of practice for use of
ceilings and floors of solid aluminium alloys in
construction structures
2470 Code of practice for (2) 13416 Recommendations for
installation of septic tanks: (Part 5): 1994 preventive measure against
(Part 1): 1985 Design criteria and hazards at workplaces:
construction (second Part 5 Fire protection
revision) (3) 11769 Guidelines for safe use of
(Part 2): 1985 Secondary treatment and (Part 1): 1987 products containing
disposal of septic tank asbestos: Part 1 Asbestos
effluent (second revision) cement products

PART 7 CONSTRUCTIONALPRACTICES ANDSAFETY 65


IS No. Title 1S No. Title
(4) 2190:1992 Code of practice for 2266:2002 Specification for steel
selection, installation and wire ropes for general
maintenance of portable engineering purposes ~orth
first-aid fiie extinguishers revision)
(third revision) (21) 818: 1%8 Code of practice for safety
(5) 8758:1993 Recommendations for fire and health requirements in
precautionary measures in electric and gas welding
construction of temporary and cutting operations (fhst
structures and pandals (first revision)
revision) (22) 5916:1970 Safety code for
(6) 10439:1983 Code of practice patent constructions involving use
glazing of hot bituminous materials
14687:1999 Guidelines for falsework (23) 13416 Recommendations for
for concrete structures (Part 4): 1994 preventive measure against
hazards at workplaces:
(7) 3764:1992 Safety code for excavation
Part 4 Timber structure
work (first revision)
(24) 2171:1999 Specification for portable
(8) 4138:1977 Safety code for working
fire extinguishers, dry
in compressed air (first
powder (Cartridge type)
revision)
(third revision)
(9) 2925:1984 Specification for industrial
(25) 819:1957 Code of practice for
safety helmets (second
resistance spot welding for
revision)
light assemblies in mild
(10) 2750:1964 Specification for steel steel
scaffoldings
1261:1959 Code of practice for seam
(11) 3696 Safety code for scaffolds welding in mild steel
(Part 1): 1987 and ladders: Part 1 Scaffolds
3016:1982 Code of practice for fire
(12) 3696 Safety code for scaffolds precautions in welding and
(Part 2): 1991 and ladders: Part 2 Ladders cutting operations (first
(13) 4912:1978 Safety requirements for revision)
floors and wall openings, 4081:1986 Safety code for blasting and
railing and toe boards (first related drilling operations
revision) @rst revision)
(14) 11461:1985 Code of practice for 4138:1977 Safety code for working in
compressor safety compressed gas (first
(15) 1179:1967 Specification for equipment revision)
for eye and face protection 9595:1996 Recommendations for
during welding (first metal arc welding of carbon
revision) and carbon manganese
(16) 5983:1980 Specification for eye- steels @W revision)
protectors (first revision) 10178:1995 “Recommended procedure
(17) 2361:2002 Specification for bull-dog for COZ gas shielded metal-
grips (third revision) arc welding of structural
(18) 11057:1984 Specification for industrial steels (j?rst revision)
safety nets (26) 3844:1989 Code of practice for
(19) 3016:1982 Code of practice for fire installation and maintenance
precautions in welding and of internal fire hydrants and
cutting operations (first hose reels on premises (/irst
revision) revision)
(20) 1084:1994 Specification for manila 5290:1993 Specification for landing
ropes (fourth revision) valves (third revision)

66 NATIONALBUILDING CODE OF INDIA


IS No. Title 1S No. Title

(27) 13416 Recommendation for 2029:1998 Specification for ring


(Part 2): 1992 preventive measures wrenches (spanners)
against hazards at work ~ourth revision)
places:Part2FaUprevention 2030:1989 Specification for box
(28) 13416 Recommendation for spanners (second revision)
(Part 1): 1992 preventive measures 2094 Specification for heater for
against hazards at work bitumen (tar) and emulsion
places: Part 1 Falling (second revision):
material hazard prevention (Part 1): 1996 Specification (second
(29) 13416 Recommendation for revision)
(Part 3) :1994 preventive measures against (Part 2): 1999 Bitumen sprayer (third
hazards at work places: revision)
Part 3 Disposal of debris
(Part 3): 1999 Emulsion (third revision)
(30) 274 Specification for shovels:
2431:1963 Specification for steel
(Part 1) :1981 General purpose shovels wheel barrows (single
(third revision) wheel-type)
(Part 2): 1981 Heat-treated shovels (third 2438:1963 Specification for roller pan
revision) mixer
663:1980 Specification for adzes 2439:1963 Specification for metal
(second revision) hand rollers (fixed-weight
704:1984 Specification for crow bars type)
and claw bars (second 2505:1992 Specification for concrete
revision) vibrators, immersion type
841:1983 Specification for steel (general requirements)
hammers (second revision) 2506:1985 General requirements for
844 Specification for screw screed board concrete
drivers: vibrators @-st revision)

(Part 2): 1979 Dimensions (second 2514:1963 Specification for concrete


revision) vibrating tables

(Part 3): 1979 Dimensions for screw 2587:1975 Specification for pipes
drivers for recessed head vices (open side type and
screws (second revision) fixed sides type) (first
revision)
1630:1984 Specification for mason’s
tools for plaster work and 2588:1975 Specification for
pointing work (first blacksmith’s vices (first
revision) revision)

1759:1986 Specification for 2722:1964 Specification for portable


PO WRAHS (second swing weigh hatchers for
revision) concrete (single and double
bucket type)
1791:1985 Specification for batch type
concrete mixers (second 2852:1998 Specification for carpenters
revision) augers (first revision)

1930:1995 Specification for chisels 3066:1965 Specification for hot


and gauges (second asphalt mixing plants
revision) 3251:1965 Specification for asphalt
1931:2000 Spec31cation for engineer’s paver finisher
files (third revision) 3365:1965 Specification for floor
2028:2004 Specification for open jaw polishing machines
wrenches (spanners) 3559:1966 Specification for pneumatic
~ourth revision) concrete breakers

PART 7 CONSTRUCTIONALPRACTICES ANDSAFETY 67


IS No. Title IS No. Title
3587:1986 Specification for rasps 5684:1970 Specflcation for pipe vices
(second revision) (chain type)
3650:1981 Specification for 5697:1970 Specification for ripping
combination side cutting chisels
pliers (second revision) 5889:1994 Specification for vibratory
3938:1983 Specification for electric plate compactor (first
wire rope hoists (second revision)
revision) 5890:1970 Specification for mobile
4003 Specification for pipe hot mix asphalt plants, light
wrenches duty

(Part 1): 1978 General purposes (first 5891:1970 Specification for hand-
revision) operated concrete mixer
5995:1971 Specification for pipe grip
(Part 2) :1986 Heavy duty (first revision)
pliers
4017:1992 Specification for carpenters
6007:1971 Specification for pipe vices
squares (jirst revision)
(hinged type)
4057:1986 Specificationforcarpenters
6078:1986 Specification for line man’s
adjustable metal bodied
pliers (second revision)
bench planes (jrst revision)
6087:1971 Specification for metal
4095:1991 Specification for pincers
cutting shears
(second revision)
6118:1991 Specification for multiple
4183:1967 Specification for metal slip joint pliers (first
hand rammers revision)
4184:1967 Specification for steel wheel 6149:1984 Specification for single
barrows (with two wheels) ended open jaw adjustable
4508:1992 Specification for open wrenches (jrst revision)
ended slugging wrenches 6375:1991 Specification for wood
(spanners) (first revision) splitting wedges (first
4656:1968 Specification for form revision)
vibrators for concrete 6389:1998 Specification for
4915:1968 Specification for welders combination wrenches with
chipping hammer equal openings (second
revision)
5066:1969 Specification for glass
pliers 6428:1972 Specification for pile frame

5067:1969 Specification for fencing 6430:1985 Specification for mobile


pliers air compressor for
construction purposes (first
5087:1969 Specification for wire
revision)
stripping pliers
6433:1972 Specification for guniting
5098:1969 Specification for cross cut
~uipment
and rip saws
6546:1989 ‘Specification for claw
5123:1969 Specification for tenon and
hammers (/irst revision)
dovetail saws
6836:1973 Specification for hand
5169:1986 Specification for hack-saw snaps and set-ups for solid
frames (first revision) rivets
5200:1998 Specification for bolt 6837:1973 Specification for three
clippers (first revision) wheel type pipe cutter
5658:1990 Specification for snipenose 6841:1973 Specification for wrecking
pliers @-st revision) bars
5663:1970 Specification for brick and 6861:1973 Speciilcation for engineers’
mason’s chisels scrapers

68 NATIONALBUILDINGCODE OF INDIA
IS No. Title IS No. Title
6881:1973 Specification for link type (32) 15183 Maintenance management
pipe cutters (Part 3): 2002 for buildings — Guidelines:
6891:1973 Specification for carpenter’s Part 3 Labour
auger bits (33) 15183 Maintenance management
6892:1973 Specification for (Part 2): 2002 for buildings — Guidelines:
b~acksmith’s brick-iron Part 2 Finance
7041: 973 Specification for carpenter’s (34) 3935:1993 Guidelines for repair and
plain brace seismic strengthening of
7042: 973 Specification for carpenter’s buildings
ratchet brace (35) 3828:1993 Improving earthquake
7077: 973 Specification for bending resistance of low strength
bars masonry buildings —
7958:1976 Specification for hand vices Guidelines
8202:1994 Specification for carpenter’s (36) 13827: 199; Improving earthquake
wooden bodied planes @rst resistance of earthen
revision) buildings — Guidelines
8671:1977 Specification for nail puller (37) 4130:1991 Safety code for demolition
(31) 7293:1974 Safety code for working with of buildings (second
construction machinery revision)

PART 7 CONSTRUCTIONALPRACTICES ANDSAFETY 69


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES

Section 1 Lighting and Ventilation

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 ORIENTATION OF BUILDING ... 8
4 LIGHTING ... 11
5 VENTILATION ... 35

ANNEX A SKY COMPONENT TABLES ... 43

LIST OF STANDARDS .,, 47

2 NATIONALBUILDtNG CODE OF LNDIA


National Building Code Sectional Committee, CED 46

FOREWORD

Illumination levels for different tasks are recommended to be achieved either by daylighting or artificial lighting
or a combination of both. This Section, read together with Part 8 ‘Building Services, Section 2 Electrical and
Allied Installations’, adequately covers the illumination levels required and methods of achieving the same.

Ventilation requirements to maintain air quality and control body odours in terms of air changes per hour and to
ensure thermal comfort and heat balance of body are laid for different occupancies and the methods of achieving
the same by natural means are covered in this Section. The provisions on mechanical ventilation are covered in
Part 8 ‘Building Services, Section 3 Air Conditioning, Heating and Mechanical Ventilation’.

Climatic factors which normally help in deciding the orientation of the buildings to get desirable benefits of
lighting and ventilation inside the buildings are also covered in this Section.

This Section was first published in 1970. The first revision of the Section was brought out in 1983. In this
revision, some provisions have been updated based on the information given in the SP 41 : 1987 ‘Handbook on
functional requirements of buildings (other than industrial buildings)’; other major changes in this revision are:

a) Rationalization of definitions and inclusion of definitions for some more terms.


b) A climatic classification map of India based on a new criteria has been included.
c) Data on total solar radiations incident on various surfaces of buildings for summer and winter seasons
have been updated.
d) Design guidelines for natural ventilation have been included.
e) For guidelines on mechanical ventilation, reference to Part 8 ‘Building Services, Section 3 Air
Conditioning, Heating and Mechanical Ventilation’ has been made, where these provisions have now
been covered exhaustively.
o Rationalized method for estimation of desired capacity of ceiling fans and their optimum height above
the floor for rooms of different sizes have been included.
g) Design sky illuminance values for different climatic zones of India have been incorporated.

Energy efficiency is an important aspect being taken care of in this revision of the Code. Accordingly, the
relevant requirements for energy efficient system for lighting and ventilation have been duly included in the
concerned provisions under this Section.

The provisions of this Section are without prejudice to the various Acts, Rules and Regulations including the
Factories Act, 1948 and Rules and Regulations framed thereunder.

The information contained in this Section in largely based on the following Indian Stan@rds/Special publications:

IS 2440:1975 Guide for daylighting of buildings (second revision)


IS 3103:1975 Code of practice for industrial ventilation (@W revision) ‘
IS 3362:1977 Code of practice for natural ventilation of residential buildings @-,rt revision)
1S 3646 Code of practice for interior illumination: Part 1 General requirements and
(Part 1) :1992 recommendations for building interiors (jirst revision)
IS 7662 Recommendations for orientation of buildings: Part 1 Non-industrial buildings
(Part 1): 1974
IS 11907:1986 Recommendations for calculation of solar radiation on buildings
SP 32:1986 Handbook on functional requirements of industrial buildings (lighting and ventilation)
SP41 :1987 Handbook on functional requirements of buildings other than industrial buildings

Provisions given in National Lighting Code (under preparation) may also be referred.

PART 8 BUILDINGSERVICES — SECTION 1 LIGHTING ANDVENTILATION 3


The following publication has also been referred to in the preparation of this Section:

Report on energy conservation in buildings, submitted to Department of Power, Ministry of Energy by


Central Building Research Institute, Roorkee.

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

NATIONAL BUILDING CODE OF INDIA


“\ “AL
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES
Section 1 Lighting and Ventilation

1 SCOPE 2.1.6 Clear Design Sky — The distribution of


luminance of such a sky is non-uniform; the horizon
This Section covers requirements and methods for
is brighter than the zenith, and when LZis the brightness
lighting and ventilation of buildings.
at zenith, the brightness at an altitude (0) in the region
2 TERMINOLOGY away from the sun, is given by the expression:

2.0 For the purpose of this Section, the following Lo = L= cosec @


definitions shall apply.
when O lies between 15° and 90°, and LO is constant
2.1 Lighting when O lies between 0° and 15°.

2.1.1 Altitude (/3) — The angular distance of any point 2.1.7 Colour Rendering Index (CRI) — Measure of
of celestial sphere, measured from the horizon, on the the degree to which the psychophysical colour of an
great circle passing through the body and the zenith object illuminated by the test illuminant conforms to
(see Fig. 1). that of the same object illuminated by the reference
illuminant, suitable allowance having been made for
2.1.2 Azimuth (q!I ) — The angle measured between
the state of chromatic adaptation.
meridians passing through the north point and the point
in question (point C in Fig. 1). 2.1.8 Correlated Colour Temperature (CCT) (Unit:
K) — The temperature of the Planckian radiator whose
z
perceived colour most closely resembles that of a given
stimulus at the same brightness and under specified
viewing conditions.

2.1.9 Daylight Area — The superficial area on the


working plane illuminated to not less than a specified
s daylight factor, that is, the area within the relevant
contour.

2.1.10 Daylight Factor — The measure of total


daylight illuminance at a point on a given plane
‘MERIDIAN
expressed as the ratio (or percentage) which the
NA illuminance at the point on the given plane bears to
the simultaneous illuminance on a horizontal plane due
REFERENCES
to clear design sky at an exterior point open to the
o- Observer’s station S – Geographical south whole sky vault, direct sunlight being excluded.
c- Celestial body E – Geographical east
z- Zenith W – Geographical west 2.1.11 Daylight Penetration — The maximum
NA - Nadir N - Geographical north distance to which a given daylight factor contour
penetrates into a room.
FIG. 1 ALTITUDE AND AZIMUTH OF A
CELESTIALBODY 2.1.12 Direct Solar Illuminance — The illurninance
from the sun without taking into account the light from
2.1.3 Brightness Ratio or Contrast — The variations
the sky.
or contrast in brightness of the details of a visual task, ,
such as white print on blackboard. 2.1.13 External Rejlected Component (ERC) — The
ratio (or percentage) of that part of the daylight
2.1.4 Candela (cd) — The S1 unit of luminous
illuminance at a point on a given plane which is
intensity.
received by direct reflection from external surfaces as
Candela = 1 lumen per steradian compared to the simultaneous exterior illuminance on
a horizontal plane from the entire hemisphere of an
2.1.5 Central Field — The area of circle round the
unobstructed clear design sky.
point of fixation and its diameter, subtending an angle
of about 2° at the eye. Objects within this area are most 2.1.14 Glare — A condition of vision in which there
critically seen in both their details and colour. is discomfort or a reduction in the ability to see

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 5


‘-”T-

significant objects or both due to an unsuitable 2.1.24 Orientation of Buildings — In the case of non-
distribution or range of luminance or due to extreme square buildings, orientation refers to the direction of
contrasts in space and time. the normal to the long axis. For example, if the length
of the building is east-west, its orientation is north-
2.1.15 Illuminance — At a point on a surface, the ratio
south.
of the luminous flux incident on an infinitesimal
element of the surface containing the point under 2.1.25 Peripheral Field — It is the rest of the visual
consideration to the area of the element. field which enables the observer to be aware of the
spatial framework surrounding the object seen.
NOTE — The unit of illuminance (the measurement of
illumination) is Iux which is 1 lumen per square metre. NOTE — A central part of the peripheral field, subtendkrg an
angle of about 30° on either side of the point of fixation, is
2.1.16 Internal Reflected Component (IRC) — The chiefly involved in the perception of glare.
ratio (or percentage) of that part of the daylight
illuminance at a point in a given plane which is received 2.1.26 Reflected Glare — The variety of ill effects on
by direct reflection or inter-reflection from the internal visual efficiency and comfort produced by unwanted
surfaces as compared to the simultaneous exterior reflections in and around the task area.
illuminance on a horizontal plane due to the entire 2.1.27 Reflection Factor (Reflectance) — The ratio
hemisphere of an unobstructed clear design sky. of the -luminous flux reflected by a body (with or
2.1.17 Light Output Ratio (LOR) or Eficiency (~) — without diffision) to the flux it receives. Some symbols
The ratio of the luminous flux emitted from the used for reflection factor are:
luminaire to that emitted from the lamp(s) (nominal rc = Reflection factor of ceiling.
luminous flux). It is expressed in percent.
rw = Reflection factor of parts of the wall between
2.1.18 Lumen (lm) — S1 unit of luminous flux. The the working surface and the luminaires.
luminous flux emitted within unit solid angle (one = Reflection factor of floor.
rf
steradian) by a point source having a uniform intensity
of one candela. 2.1.28 Reveal — The side of an opening for a window.

2.1.19 Luminance (At a point of a Su~ace in a Given 2.1.29 Room Index (k,) — An index relating to the shape
Direction) (Brightness) — The quotient of the of a rectangular interior, according to the formula:
luminous intensity in the given direction of an
infinitesimal element of the surface containing the k, = ‘“w
(L+W) Iim
point under consideration by the orthogonally
projected area of the element on a plane perpendicular where L and W are the length and width respectively
to the given direction. The unit is candela per square of the interior, and H~ is the mounting height, that is,
metre (cd/m*). height of the fittings above the working plane.
2.1.20 Luminous Flux (@)— The quantity characteristic NOTES
of radiant flux which expresses its capacity to produce 1 For rooms where the length exceeds 5 times the width, L
visual sensation evaluated according to the values shall Lwtaken aa L = 5W.
of relative luminous efficiency for the light adapted 2 If the reflection factor of the upper stretch of the wrdls is
less than half the reflection factor of the ceiling, for indirect or
eye:
for the greater part of indirect fighting, the vrdrreHmis measured
a) E“ective luminousflux ( ~,) — Total luminous between the ceiling and the working plane.
flux which reaches the working plane. 2.130 Sky Compommt(SC)-The ratio (or percentage)
b) Nominal luminousflux (@O)— Total luminous of that part of the daylight illuminance at a point on a
flux of the light sources in the interior. given plane which is recei4ed directly from the sky as
2.1.21 Maintenance Factor (d) — The ratio of the compared to the simultaneous exterior illuminance on
average illuminance on the working plane after a a horizontal plane from the entire hemisphere of art
certain period of use of a lighting installation to the unobstructed clear design sky.
average illuminance obtained under the same 2.1.31 Solar Load — The amount of heat received
conditions for a new installation. into a building due to solar radiation which is affected
2.1.22 Meridian — It is the great circle passing through by orientation, materials of construction and reflection
the zenith and nadir for a given point of observation. of external finishes and colour.

2.1.23 North and South Points — The point in the 2.1.32 Utilization Factor (Coe@cient of Utilizaiton)
respective directions where the meridian cuts the (A) — The ratio of the total luminous flux which
horizon. reaches the working plane (effective luminous

6 NATIONALBUILDINGCODE OF INIXA
flux, @~)to the total luminous flux of the light sources be carried out by a competent authority having jurisdiction and
in the interior (nominal luminous flux, @O). if the outside air of the quality specified is not available, filtration
and other treatment devices shall be used to bring its quality to
or above the levels mentioned in Table 1. ,, ~
2.1.33 Visual Field -— The visual field in the binocular ;
which includes an area approximately 120° vertically 2 The list of contaminants given in Table,1 is not exhaustive
and 160° horizontally centering on the point to which and available special literature may be referred for data on
other contaminants.
the eyes are directed. The line joining the point of
/
fixation and the centre of the pupil of each eye is called Table 1 Maximum Allowable Contaminant
its primary line of sight. Concentrations for Ventilation Air Contaminants
2.1.34 Working Plane — A horizontal plane at a level Annual Average (Arithmetic Mean) i“ 1
at which work will normally be done (see 4.1.3.3 (Clause 2.2.9)
and 4.1.3.4).
Contaminants Annual Short-Term Averaging
2.2 Ventilation Average Level (Not Period
(Arithmetic to exceed
2.2.1 Air Change per Hour — The amount of air Mean) More than I
Once a ‘i
leakage into or out of a building or room in terms of t
Year) k ?
the number of building volume or room volume f
pg/m3 pg/m3 h
exchanged.
(1) (2) (3) (4)
2.2.2 Axia[ Flow Fan — A fan having a casing in Suspended particuktes 60 150 24
which the air enters and leaves the impeller in a Sulphur oxides 80 400 24
direction substantially parallel to its axis. Carbon monoxide 20000 30000 8

2.2.3 Centrijtigal Fan — A fan in which the air leaves Photochemical oxidant 100 500 1
the impeller in a direction substantially at right angles Hydrocarbons (not 1800 4000 3
including methanes)
to ils axis.
Nitrogen oxide 200 500 24
2.2.4 Contaminants — Dusts, fumes, gases, mists, Odouc Essentially
vapours and such other substances present in air as are unobjectionable
likely to be injurious or offensive to the occupants.
2.2.10 Ge~~ral ventilation — ventilation, either
2.2.5 Dilution Ventilation — Supply of outside air to *
natural or mechanical or both, so as to improve the
reduce the air-borne concentration of contaminants in
general environment of the building, as opposed to
the building.
local exhaust ventilation for contamination control.
2.2.6 Dry Bulb Temperature — The temperature of
2.2.11 Globe Temperature — The temperature
the air, read on a thermometer, taken in such a way as
measured by a thermometer whose bulb is enclosed in
to avoid errors due to radiation.
a matt black painted thin copper globe of 150 mm
2.2.7 E~ective Ternperatzwe (ET) — An arbitrary index diameter. It combines the influence of air temperature
which combines into a single value the effect of and thermal radiations received or emitted by the
temperature, humidity and air movement on the bounding surfaces.
sensation of w,armth or cold felt by the human body
2.2.12 Humidification — The process whereby the
and its numerical value is that of the temperature of
absolute humidity of the air in a building is maintained
still saturated air which would induce an identical
at a higher level than that of outside air or at a level
sensation.
higher than that which would prevail naturally.
2.2.8 Exhaust @’Air — Removal of air from a building
2.2.13 Humidity, Absolute — The mass of water
or a room and its disposal outside by means of a
vapour per unit volume.
mechanical device, such as a fan.
2.2.9 Fresh Air or Outside Air — Air of that quality, 2.2.14 Humidity, Relative — The ratio of the partial
pressure or density of the water vapour in the air to the
which meets the criteria of Table 1 and in addition
saturated pressure or density respectively of water
shall be such that the concentration of any contaminant
in the air is limited to within one-tenth the threshold vapour at the same temperature.
limit value (TLV) of that contaminant. 2.2.15 Local Exhaust Ventilation — Ventilation
N 0T13S effected by exhaust of air through an exhaust appliance,
1 Where it is reasonably believed that the air of quality is such as a hood with or without fan located as closely
unexpectable m; indicated above, sampling and analysis shall as possible to the point at which contaminants are

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 7


.

released, so as to capture effectively the contaminants in air at that point by causing the air to flow into the
and convey them through ducts to a safe point of exhaust hood.
discharge.
2.2.26 Ventilation — Supply of outside air into, or
2.2.16 Make-up Air — Outside air supplied into a the removrd of inside air from an enclosed space.
building to replace the indoor air.
2.2.27 Wet Bulb Temperature —The steady temperature
2.2.17 Mechanical Ventilation — Supply of outside air finally given by a thermometer having its bulb covered
either by positive ventilation or by infiltration by with gauze or muslin moistened with distilled water
reduction of pressure inside due to exhaust of air, or and placed in an air stream of not less than 4.5 m/s.
by a combination of positive ventilation and exhaust
of air. 3 ORIENTATION OF B~ING

2.2.18 Natural Ventilation — Supply of outside air 3.1 The chief aim of orientation of buildings is to
into a building through window or other openings due provide physically and psychologically comfortable
to wind outside and convection effects arising from living inside @c building by creating -ti&$ which
temperature or vapour pressure differences (or both) suitably and w~sfully. w@, off the undesirable
between inside and outside of the building. effects of severe weat@K @ a cops@erable extent by
judicious use of the recommendations and knowledge
2.2.19 Positive Ventilation — The supply of outside of climatic factors.
air by means of a mechanical device, such as a fan.
3.2 Basic Zones
2.2.20 Propeller Fan — A fan in which the air leaves
the impeller in a direction substantially parallel to its 3.2.1 For the purpwe of design of buildings, the
fixis :%gc -3 ‘r ~perate normally under free inlet and country may be divided into the major climatic zones
outiet conditions. as given in Table 2, which also gives the basis of this
classification.
2.2.21 Spray-Head System — A system of atomizing
water so as to introduce free moisture directly into a Table 2 Classification of Climate
building.
(Clause 3.2.1)
2.2.22 Stack E#ect — Convection effect arising from
temperature or vapour pressure difference (or both) stC3im@c Mean Monthtj Mean Montidy
No. Zoae Maximum Relative Humidity
between outside and inside of the room and the Temperature (“C) Percentage
difference of height between the outlet and inlet (1) (2) {3) (4)
openings.
i) Hot-Dry above 30 below 55
2.2.23 Tropical Summer Index (TSI) — The temperature ii) Warm-Humid above 30 above 55
above 25 above 75
of calm air at 50 percent relative humidity which iii) Temperate between 25-30 below 75
imparts the same thermal sensation as the given iv) Cold below 25 Atl vatues
environment. TSI (in ‘C) is express as v) Composite see 3.2.2

0.745 t,+0.308 tW–2.06 F+ 0.841 The climatic classification map of India is shown in
Fig. 2.
where
3.2.2 Each climatic zong does not have same climate
tz = Globe temperature, ‘C; for the whole yew, it has a particular season for more
tw = Wet bulb temperature, “C; and than six months and may experience other seasons for
v = Wind speed, m/s. the remaining period. A @imatic zone that does not
have any season for more than six months may be
2.2.24 Threshold Limit Value (TLV) — Refers to air- called as composite zone.
borne concentration of contaminants currently accepted
by the American Conference of Governmental 3.3 Climatic Factors
Industrial Hygienists and represents conditions under
From the point of view of lighting and ventilation, the
which it is believed that nearly all occupants may be
following climatic factors influence the optimum
repeatedly exposed, day after day, without adverse
orientation of the building:
effect.
a) solar radiation and temperature
2.2.25 Velocity, Capture — Air velocity at any point
b) relative humidity, and
in front of the exhaust hood necessary to overcome
opposing air currents and to capture the contaminants c) prevailing winds.

8 NATIONAL BUILDING CODE OF INDIA


.

=J* . .. .. . . . .
“ 2!-.
\“~.*..:
t:” , ‘,- ,“ :. ,“: ,.:Y+;7:T?)
. J.’
. . . ””.”

\
.
. . ... .‘ . . ..
. . . ... . .. . . . . .
+
. . .
...” . .
. .
. .
.,,,
..”.

.
,:-.
. .

“. ‘.. . , . .
.:$...
.<.

f
. .. .
. .
.
. .
. ., ..:-.
.O
““
:J MAP OF INDIA
.- ..,:., . . . ..ax
SHOWING
.:.-
.-
CLIMATIC ZONES
) .#.
.“,. .” .
100km O
~h
..-.

L,

r f \

* 1
—

ENDS

IsN HOT-DRY

*
,1

1!
WARM - HUMID
1 I
●

UIIInl COMPOSITE

,,,,,
,,,
///
.
.
? ,,,,,,.,,,
,.,,
,,,,,
,.,
,,,//
//,.,,,
,,,,
n ,,,, TEMPERATE
“d

8 n“.”... :.. . :
.:: ;:...:.:: ::
‘.
.: .,: ;: y.
COLD

?f
I
?4”
1 h
d u“
I I
24 w’
! t)
Based upon Survey of India Outline Map printed in 1$93. @Government of India Copyright, 2005

The territorial waters of India extend into the seato a dwtance of twelve nautical miles measured from the appropriate baaa line.
The boundary of Meghalaya shown on this map is as interpreted fkom the North-Eastarn Areas (Reorganisation) Act, 1971, but has yet to be varitiad.
Responsibility for correctness of internal detds shown on the map resta with the publisher.
The state boundaries between Uttaranchal & Uttar Pradesh, Bihar& Jharkhand and Chhatisga~ & Madhya Pradesh have not been verified by Governments concerned.

FIG. 2 MAP OFINDIASHOWINGCLIMATICZONES

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 9


3.4 Solar Radiation high humidity with high temperatures. With the
introduction of electric fan to effectively circulate air
3.4.1 The best orientation from solar point of view
and owing to taking into account the rise in cost of
requires that the building as a whole should receive
construction of buildings, it would perhaps be better
the maximum solar radiation in winter and the
to shift the emphasis on protection from solar radiation
minimum in summer. For practical evaluation, it is
where temperatures are very high. When, however,
necessary to know the duration of sunshine, and hourly
there is less diurnal variation between morning and
solar intensity on the various external surfaces on
mean maximum temperatures along with high
representative days of the seasons. The total direct plus
humidity, as in coastal areas, the emphasis should be
diffused diurnal solar loads per unit area on vertical
on prevailing winds.
surface facing different directions are given in Table 3
for two days in the year, that is, 22 June and 22 3.5.1.1 For the purpose of orientation, it is necessary
December, representative of summer and winter, for to study the velocity and direction of the wind at each
latitudes corresponding to some important cities all hour and in each month instead of relying on
over India. From Table 3, the total heat intake can be generalizations of a month or a period or for the year
calculated for all possible orientations of the building as a whole. This helps to spot the right winds for a
for these extreme days of summer and winter. particular period of day or night.

3.4.1.1 Except in cold climatic zone, suitable sun- 3.5.1.2 It is generally found that variation up to 30°
breakers have to be provided to cut off the incursion with respect to the prevalent wind direction does not
of direct sunlight to prevent heat radiation and to avoid materially affect indoor ventilation (average indoor air
glare. speed) inside the building.

3.5.2 In hot-dry climate, advantage can be taken of


3.5 Relative Humidity and Prevailing Winds
evaporative cooling in summer to cool the air before
3.5.1 The discomfort due to high relative humidity introducing it into the building. But in warm humid
in air when temperatures are also high can be climate, it is desirable either to regulate the rate of air
counteracted, to a great extent, by circulation of air movement with the aid of electric fans or to take
with electric fans or by ventilation. In the past, advantage of prevailing winds.
simultaneously with heavy construction and
3.6 Aspects of Daylighting
surrounding VERANDAHS to counter the effect of
sun’s radiation, there was also an over emphasis on Since the clear design sky concept for daylighting takes
prevailing winds to minimize the adverse effects of care of the worst possible situation, orientation is not

Table 3 Total Solar Radiation (Direct plus Diffused) Incident on Various Surfaces of
Buildings in W/m2/day for Summer and Winter Seasons
(Clause 3.4.1)

Orientation Latitude
*- -
A / -
/ -1 9°N 13°N 17“N 21°N 25”N 29°N
(1) (2) (3) (4) (5) (6) (7) (8)

Nm-th Summer 1494 1251 2102 1775 2173 1927


Winter 873 859 840 825 802 765
North-East Summer 2836 2717 3144 3092 3294 3189
Winter 1240 1158 1068 1001 912 835
East Summer 3344 3361 3475 3598 3703 3794
Winter 2800 2673 2525 2409 2211 2055
South-East Summer 2492 2660 2393 2629 2586 2735
Winter 3936 3980 3980 3995 3892 3818
South Summer 1009 1185 1035 1117 1112 1350
Winter 4674 4847 4958 5059 4942 4981
South-West Summer 2492 2660 2393 2629 2586 2735
Winter 3936 3980 3980 3995 3892 3818
West Summer 3341 3361 3475 3598 3703 3794
Winter 2800 2673 2525 2409 2211 2055
North-West Summer 2836 2717 3144 3092 3294 3189
Winter 1240 1158 1068 1001 912 835
Horizontal Summer 8107 8139 8379 8553 8817 8863
Winter 6409 6040 5615 5231 4748 4281

10 NATIONAL BUILDING CODE OF INDIA

..
a major problem for daylighting in buildings, except f) installation of emergency lighting systems,
that direct sunshine and glare should be avoided. where necessary.
However, due allowance should be given to the mutual
4.1.2 Planning the Brightness Pattern
shading effects of opposite facades.
The brightness pattern seen within an interior maybe
3.7 Planting of Trees
considered as composed of three main parts — the task
Planting of trees in streets and in open spaces should itself, immediate background of the task and the general
be done carefully to take advantage of both shades and surroundings of walls, ceiling, floor, equipment and
sunshine without handicapping the flow of natural furnishings.
winds. Their advantage in abating glare and in
providing cool andlor warm pockets in developed areas 4.1.2,1 In occupations where the visual demands are
should also be taken, Some trees shed leaves in winter small, the levels of illumination derived from a
while retaining thick foliage in summer. Such trees criterion of visual performance alone maybe too low
will be very advantageous, particularly where southern to satisfy the other requirements. For such situations,
and western exposures are concerned, by allowing therefore, ilh.uninance recommendations are based on
maximum sun during winter and effectively blocking standards of welfare, safety and amenity judged
it in summer. appropriate to the occupations; they are also sufficient
to give these tasks brightness which ensured that the
3.8 For detailed information regarding orientation of visual performance exceeds the specified minimum.
buildings and recommendations for various climatic Unless there are special circumstances associated
zones of country, reference may be made to good with the occupation, it is recommended that the
practice [8-1(1)]. illurninance of all working areas within a building
should generally be 150 lUX, even though the visual
4 LIGHTING
demands of the occupation might be satisfied by lower
4.1 Principles of Lighting values.

4.1.1 Aims of Good Lighting 4.1.2.2 Where work takes place over the whole
utilizable area of room, the illumination over that area
Good lighting is necessary for all buildings and has
should be reasonably uniform and it is recommended
three primary aims. The first aim is to promote work
that the uniformity ratio (minimum illuminance divided
and other activities carried out within the building; the
by average illuminance levels) should be not less than
second aim is to promote the safety of the people using
0.7 for the working area.
the building; and the third aim is to create, in
conjunction with the structure and decoration, a 4.1.2.3 When the task brightness appropriate to an
pleasing environment conducive to interest of the occupation has bepn determined, the brightness of the
occupants and a sense of their well-being. other parts of the room should be planned to give a
proper emphasis to visual comfort and interest.
4.1.1.1 Realization of these aims involves:
a) careful planning of the brightness and colour A general guide for the brightness relationship within
pattern within both the working areas and the the normal field of vision should be as follows:
surroundings so that attention is drawn a) For high task brightness Maximum
naturally to the important areas, detail is seen (above 100 cdhn2)
quickly and accurately and the room is free 1) Between the visual task 3tol
from any sense of gloom or monotony and the adjacent areas
(see 4.1.3); like table t@s
b) using directional lighting where appropriate 2) Between the visual task lo to 1
to assist perception of task detail and to give and the remote areas of
good modeling; the room
c) controlling direct and reflected glare from b) For low and medium task brightness (below
light sources to eliminate visual discomfort; 100 cd/m2): The task should be brighter than
d) in artificial lighting installations, minimizing both the background and the surroundings;
flicker from certain types of lamps and paying the lower the task brightness, the less critical
attention to the colour rendering properties is the relationship.
of the light;
4.1.3 Recommended Values of Illuminance
e) correlating lighting throughout the building to
prevent excessive differences between adjacent Table 4 gives recommended values of illuminance
areas so as to reduce the risk of accidents; and commensurate with the general standards of lighting

PART 8 BUILDINGSERVICES — SECTION 1 LIGHTING ANDVENTILATION 11


described in this section and related to many generatly 750 mm above the floor level. For certain purposes,
such as viewing the objects of arts, the illumination levels
occupations and buildings; These are valid under most
recommended are for the vertical plane at which the art pieces
of the conditions whether the illumination is by are placed.
daylighting, artificial lighting or a combination of the
two. The great variety of visual tasks makes it 4.1.3.4 Where the task is localized, the recommended
value is that for the task only; it need not, and
impossible to list them all and those given should be
sometimes slmuld not, be, the general level of
regarded as representing types of task.
illumination used throughout the interior. Some
4.1.3.1 The different locations and tasks are grouped processes, such as indnstrkd $mqxMion process, call
within the following four sections: for lighting of specialized d&ign, in which case the
a) Industrial buildings and process; level of illumination is only om of fhe several factors
to be taken into account.
b) Offices, schools and public buildings;
c) Surgeries and hospitals; and 4.L4 Glare
d) Hotels, restaurants, shops and homes. Excessive contrast or abmpt and large changes in
brightness produce the effect of glare. When glare is
4.1.3.2 The illumination levels recommended in
present, the efficiency of vision is reduced rmd small
Table 4 are those to be maintained at all time on the
details or subtle changes in scene cannot be perceived.
task. As circumstances maybe significantly different
It maybe
for different interiors used for the same application or
for different conditions for the same kind of activity, a a) direct glare due to light sources within the
range of illuminances is recommended for each type field of vision,
of interior or activity instead of a single value of b) reflected glare due to reflections from light
illuminance. Each range consists of three sucessive sources or surfaces of excessive brightness,
steps of the recommended scale of illuminances. For and
working interiors the middle value of each range
c) veiling glare where the peripheral field is
represents the recommended service illuminance that
comparatively very bright.
would be used unless one or more of the factors
mentioned below apply. 4.1.4.1 An example of glare sources in daylighting is
the view of the bright sky through a window or
4.1.3.2.1 The higher value of the range should be used
skylight, especially when the surrounding wall or
when:
ceiling is comparatively dark or weakly illuminated.
a) unusually low reflectance or contrasts are Glare can be minimized in this case either by shielding
present in the task; the open sky from direct sight by louvers, external
b) errors are costly to rectify; hoods or deep reveals, curtains or other shading devices
or by cross lighting the surroundings to a comparable
c) visual work is critical;
level. A gradual transition of brightness from one
d) accuracy or higher productivity is of great
portion to the other within the field of vision always
importance; and
avoids or minimizes the glare discomfort.
e) the visual capacity of the worker makes it
.. 4.1.5 Lighting for Movement about a Building
ncessary.

4.1.3.2.2 The lower value of the range may be used Most buildings are complexes of working areas and
when: other areas, such as passages, corridors, stairways,
lobbies and entrances. The lighting of all these areas
a) reflectance or contrast are unusually high; should be properly correlated to give safe movement
b) speed and accuracy is not important and within the building at all tides.
c) the task is executed only occasionally. 4.1.5.1 Corridors, passages and stairways
4.1.3.3 Where a visual task is required to be carried Accidents may result if people leave a well-lighted
out throughout an interior, general illumination level working area and pass immediately into corridors or
to the recommended value on the working plane is on to stairways where the lighting is inadequate, as
necessary; where the precise height and location of the time needed for adaptation to the lower level may
the task are not known or cannot be easily specified, be too long to permit obstacles or the treads of stairs
the recommended value is that on horizontal plane to be seen sufficiently quickly. For the same reason, it
850 mm above floor level. is desirable that the illumination level of rooms which
NOTE — For an industrial task, working plane for the purpose open off a working area should be fairly high even
of generat illumination levels is that on a work place which is though the rooms may be used ordy occasionally.

12 NATIONAL BUILDING CODE OF INDIA


Table 4 Recommended Values of Ilhuninance
(Clauses 4.1.3,4.1 .3.2,4.3.2 and 4.3.2.1)

S1No. Type of Interior or Activity Range of Serviee Qusdity CISISS Rernorks


m runhmnee of Direct Glare
in Lux Limitation
(1) (2) (3) (4) (5)

1 AGRICULTURE AND HORTICULTURE


1.1 Inspection of Farm Produce where Colour is 300-500-750 1 I.oeal lighting maybe appropriate
Important
Other Important Tasks 200-300-500 2 Local lighting may be appropriate
1.2 Parm Workshops
1.2.1 General 50-100-150 3’
1.2.2 Workbench or tnaehine 200-300-500 2 Local or portable lighting maybe
appropriate
1.3 Milk Premises 50-1CM3-150 3
1.4 Sick Animal Pets, Calf Nurseries 30-50-100 3
1.5 Other Firru aud Horticultural Buildings 20-30-50 3
2 COAL MfNING (SURFACEBUfLDfNGS)
2.1 Coal Preparation Plant
2.1.1 Walkways, floors under conveyors 30-50-100 3
2.1.2 Wagon loading, bunkers 30-50-100 3
2.1.3 Elevators, chute transfer pits, washbox area 50-100-150 3
2.1.4 Drum filters, screen, rotating shafts 100-150-200 3
2.1.5 Picking belts 150-200-300 3 Directionaland mlour pmpertiea
of lighting may be hnpmtant for
easy reeogtdtion of coal and reek
2.2 Lamp Rooms
2.2.1 Repair section 200-300-500 2
2.2.2 Other areas 100-150-200 3
2.3 Weight Cabins, Fan Houses 100-150-200 3
2.4 Winding Houses 100-150-200 3

3 ELECTRICITY GENERATION,
TRANSMISSIONANDDISTRIBUTION
3.1 GeneralPlant
3.1.1 Turbinehouses(operatingfloor) 150-200-300 2
3.1.2 Boiler and turbine house basements 50-100-150 3
3.1.3 Boiler houses, platforms, areas around burners 50-100-150 3
3.1.4 Switch rooms, meter rooms, oil plant rooms, HV 100-150-200 2
substations (indoor)
3.1.5 Control rooms 200-300-500 1 Loealixed lighting of control
display and the control desks may
be appropriate
3.1.6 Relay and telecommunication rooms 200-300-500 2
3.L7 Diesel generator rooms, compressor rooms 100-150-200 3
3.1.8 Pump houses, water treatment plant houses 100-150-200 3
3.1.9 Battery rooms, chargers, rectifiers 50-100-150 3
3.1.10 Precipitator chambers, platforms, etc 50-100-150 3
3.1.11 Cable tunnels and basements, circulating water 30-50-100 3
culverts and screen chambers, storage tanks
(indoor), operating areas and filling points at
outdoor tanks
3.2 Coal Plant
3.2.1 Conveyors, gantries, junction towers, unloading 50-100-150 3
hoppers, ash handling plants, settling pits, dust
hoppers outlets
3.2.2 Other areas where operators may be in attendance 100-150-200 3
3.3 Nuclear Plants
Gas circulation bays, reaetor area, boiler platform, 100-150-200 2
reactor charges and discharge face

4 METAL MANUFACTURE
4.1 IronMaking
4.1.1 Sinterplartti
Plant floor 150-200-300 3

PART 8 BUILDINGSERVICES — SECTION 1 LIGHTING ANDVENTILATION 13


Table 4 — Continued

(1) (2) (3) (4) (5)

Mixer drum, fan house, screen houses, coolers, 100-150-200 3


transfer stations
4.1.2 Furnaces, cupola
General 100-150-200 3
Control platforms 200-300-500 2 Local lighting may be appropriate
Conveyor grdleries, walkways 30-50-100 3

4.2 Steel Making


4.2.1 Electric melting shops 150-200-300 3
4.2.2 Basic oxygen steel making plants
4.2.2.1 General 100-15O-2WJ 3
4.2.2.2 Convertor floor, teeming bay 150-200-300 3
4.2.2.3 Control platforms 200-300-500 2 Local lightingmay be appropriate
4.2.2.4 Scrap bays 100-150-200 3

4.3 Metal Forming and Treatment


4.3.1 Ingot stripping, soaking pits, annealing and heat 150-200-300 3
treatment bays, acid recovery plant Picking
and cleaning bays, roughing mills, cold mills,
finishing mills, tinning and galvanizing lines,
cut up and rewind lines
4.3.2 General 100-150-200 3
4.3.3 Control platformx 200-300-500 2 Local lighting may be appropriate
4.3.4 Wire mills, product finishing, steel inspection 200-300-500 3
and treatment
4.3.5 Plate/sttip inspection 300-500-700 2
4.3.6 Inspection of tin plate, stainless steeI, etc — — Special lighting to reveal faults in
the specular surface of the
material will be required
4.4 Foundries
4.4.1 Automatic Plant
4.4.1.1 Without manual operation 30-50-100 3
4.4.1.2 With occasional manual operation 100-150-200 3
4.4.1.3 With continuous manual operation 150-200-300 3
4.4.1.4 Control room 200-300-500 1 Localized lighting of the control
display md &e cc%rol desks may
be appropriate
4.4.1.5 Control platforms 200-300-500 2
4.4.2 Non-automatic plants
4.4.2.1 Charging floor, pouring, shaking out, cleaning, 200-300-500 3
grinding fettling
4.4.2.2 Rough moulding, tmrgh core making 200-300-500 3
4.4.2.3 Fine moulding, fine core rnakkg 300-500-750 2
4.4.2.4 Inspection 300-500-750 2

4.5 Forges (Severe vibration is likely to occur)


4.5.1 General 200-300-500 2
4.5.2 Inspection 300-500-750 2

5 CERAMICS
5.1 Concrete products
Mixing, casting, cleaning 150-200-300 3

5.2 Potteries
5.2.1 Grinding, moulding, pressing, cleaning, 200-300-500 3
trimming, glazing, firing
5.2.2 Enameling, colouring 5OO-75O-1OOO 1

5.3 Glass Works


5.3.1 Furnace rooms, bending, annerding 100-150-200 3
5.3.2 Mixing rooms, forming, cutting, grinding, 200-300-500 3
polishing, toughening
5.3.3 Beveling, decorative cutting, etching, silvering 300-500-750 2
5.3.4 Inspection 300-500-750 2

14 NATIONAL BUILDING CODE OF INDIA


Table 4 — Continued

(1) (2) (3) (4) (5)

6 CHEMICALS

6.1 Petroleum, Chemical and Petrochemical Works


6.1.1 Exterior walkways, platforms, stairs and ladders 30-50-100 3
6.1.2 Exterior pump and valve areas 50-100-150 3
6.1.3 Pump and compressor houses 100-150-200 3
6.1.4 Process plant with remote control 30-50-100 3
6.1.5 Process plant requiring occasional manual 50-100-150 3
intervention
6.1.6 Permanently occupied work stations in process 150-200-300 3
plant
6.1.7 Control rooms for process plant 200-300-500 1

6.2 Pharmaceutical Manufacturer and Fine Chemicals


Manufacturer
6.2.1 Pharmaceutical manufacturer
Grinding, granulating, mixing, drying, tableting, 300-500-750 2
sterilizing, washing, preparation of solutions,
filling, capping, wrapping, hardening
6.2.2 Fine chemical manufacture
6.2.2.1 Exterior walkways, platforms, stairs and ladders 36-50-100 3
6.2.2.2 Process plant 50-100-150 3
6.2.2.3 Fine chemical finishing 300-500-750 2
6.2.2.4 inspection 300-500-750 1 Local lighting may be appropriate

6.3 Soap Manufacture


6.3.1 General area 200-300-500 2
6.3.2 Automatic processes 100-200-300 2
6.3.3 Control panels 200-300-500 1 Local lighting may be appropriate
6.3.4 Machines 200-300-500 2

6.4 Paint Works


6.4.1 General 200-300-500 2
6.4.2 Automatic processes 150-200-300 2
6.4.3 Control panels 200-300-500 2
6.4.4 Special batch mixing 500-750-1000 2
6.4.5 Colour matching 750-1000-1500 1 %
7 MECHANICAL ENGINEERING

7.1 Structural Steel Fabrication


7.1.1 General 200-300-500 3
7.1.2 Marking off 300-500-750 3 Local lighting may be appropriate

7.2 Sheet Metal Works


7.2.1 Pressing, punching, shearing, stamping, spinning, 300-500-750 2
folding
7.2.2 Benchwork, scribing, inspection 500-750-1000 2

7.3 Machine and Tool Shops


7.3.1 Rough bench and machine work 200-300-500 3
7.3.2 Medium bench and machine work 300-500-750 2
7.3.3 Fine bench and machine work 500-750-1000 2
7.3.4 Gauge rooms 750-1000-1500 1 Optical aids may be required

7.4 Die Sinking Shops


7.4.1 General 300-500-750 2
7.4.2 Fine work 1000-1500-2000 1 Flexible local lighting is desirable

7.5 Welding and Soldering Shops


7.5.1 Gas and arc welding, rough spot welding 200-300-500 3
7.5.2 Medium soldering, brazing, spot welding 300-500-750 3
7.5.3 Fine soldering, fine spot welding 750-1000-1500 2 Local lighting is desirable

7.6 Assembly Shops


7.6.1 Rough work for example, frame and heavy 200-300-500 3 The lighting of vertical surface
machine assembly may be important
7.6.2 Medium work, for example, engine assembly, 300-500-750 2
vehicle body assembly
7.6.3 Fine work, for example, office machinery 500-750-1000 1 Localized lighting may be useful
assembly

PART 8 BUH.DING SERVICES — SECTION 1 LIGHTING AND VENTILATION 15

.,
Table 4 — Continued

(1) (2) (3) (4) (5)

7.6.4 Very fine work, for example, instrument 750-1000-1500 1 Local lighting and optical aids are
assembly desirable
7.6.5 Minute work, for example, watch making 1000-1500-2000 1 Local lighting and optical aids are
desirable

7.7 Inspection and Testing Shops


7.7.1 Coarse work, for example, using go/no-go 300-500-750 2 Local or localized lighting maybe
gauges, inspection of large sub-assemblies appropriate
7.7.2 Medium work, for example, inspection of 500-750-1000 1 Local or localized lighting may be
painted surfaces appropriate
7.7.3 Fine work, for example, using calibrated 750-1000-1500 1 Local or localized lighting may be
scales, inspection of precision mechanisms appropriate
7.7.4 Very fine work, for example, inspection of 1000-1500-2000 1 Local lighting and optical aids are
small intricate parts desirable
7.7.5 Minute work, for example, inspection of very 2000 1 Local lighting and optical aids are
small instruments desirable

7.8 Points Shops and Spray Booths


7.8.1 Dipping, rough spraying 200-300-500 3
7.8.2 Preparation, ordinary painting, spraying and 200-500-750 2
finishing
7.8.3 Fine painting, spraying and finishing 500-750-1000 2
7.8.4 Inspection, re-touching and matching 750-1000-1500 2

7.9 Plating Shops


7.9.1 Vats and baths 200-300-500 3
7.9.2 Buffing, polishing burnishing 300-500-750 2
7.9.3 Final buffing and polishing 500-750-1000 2
7.9.4 Inspection — — Special light to reveal fault in the
surface of the material will be
required
8 ELECTRICAL AND ELECTRONIC
ENGINEEIUNG

8.1 Electrical Equipment Manufacture


8.1.1 Manufacture of cables and insulated wires, 200-300-500 3
winding, varnishing and immersion of coils,
assembly of large machines, simple assembly work
8.1.2 Medium assembly, for example, telephones, small 300-500-750 3 Local lighting may be appropriate
motors
8.1.3 Assembly of precision components, for example, 750-1000-1500 1 Local lighting is desirable. Optical
telecommunication equipment, adjustment, aids may be useful
inspection and calibration
8.1.4 Assembly of high precision parts 1000-1500-2000 1 Local lighting is desirable. Optical
aids may be useful
8.2 Electronic Equipment Manufacture
8.2.1 Printed circuit board
8.2.1.1 Silk screening 300-500-750 1 Local lighting may be appropriate
8.2.1.2 Hand insertion of components, soldering 500-750-1000 1 Local lighting may be appropriate
8.2.1.3 Inspection 750-1000-1500 1 A large, low luminance huninaire
overhead ensures specular reflection
conditions which are helpful for
inspection of printed circuits
8.2.1.4 Assembly of wiring harness, cleating harness, 500-750-1000 1 Local lighting may be appropriated
testing and calibration
8.2.1.5 Chassis assembly 750-1000-1500 1 Local lighting may be appropriated
8.2.2 Inspection and testing
8.2.2.1 Soak test 150-200-300 2
8.2.2.2 Safety and functional tests 200-300-500 2

9 FOOD, DRINK AND TOBACCO

9.1 Slaughter Houses


9.1.1 General 200-300-500 3
9.1.2 Inspection 300-500-750 2

9.2 Canning, Preserving and Freezing


9.2.1 Grading and sorting of raw materials 500-750-1000 2 Lamp of colour rendering group
1A or lB will be required, if
colour judgement is required

16 NATIONAL BUILDING CODE OF INDIA


Table 4 — Continued

(1) (2) (3) (4) (5)

9.2.2 Preparation 300-500-750 3


9.2.3 Canned and bottled goods
9.2.3.1 Retorts 200-300-500 3
9.2.3.2 Automatic processes 150-200-300 3
9.2.3.3 Labelling and packaging 200-300-500 3
9.2.4 Frozen foods
9.2.4.1 Process area 200-300-500 3
9.2,4.2 Packaging and storage 200-300-500 3
9.3 Bottling, Brewing and Distilling
9.3.1 Keg washing and handling, bottle washing 150-200-300 3
9.3.2 Keg inspection 200-300-500 3
9.3.3 Bottle inspection — — !+reciaffighting wiff be required
9.3.4 Process areas 200-300-500 3
9.3.5 Bottle tilling 5oc-750-locro 3
9.4 Edible Oils and Fats Processing
9.4.1 Refining and blending 200-300-500 3
9.4.2 Production 300-500-750 2
9.5 Mills-Milling, Filtering and Packing 200-300-500 3
9.6 Bakeries
9.6.1 General 200-300-500 2
9.6.2 Hand decorating, icing 300-500-750 2
9.7 Chocolate and Confectionery Manufacture
9.7.1 General 200-300-500 3
9.7.2 Automatic processes 150-200-300 3
9.7.3 Hand decoration, inspection, wrapping and 300-500-750 2 If accumte colour judgments ate
packing rt!qti lamps of dour ren&ring
group lAorlBateused
9.8 Tobacco Processing
9.8.1 Material preparation, making and paeking 300-500-750 2
9.8.2 Hand processes 5OO-75O-1OOO 2

10 TEXTILES
10.1 Fibre Preparation
10.1.1 Bafe breaking, washing 200-300-500 3
10.1.2 Stock dyeing, tinting 200-300-500 3
10.2 Yam Manufacture
10.2.1 Spinning, roving, winding, etc 300-500-750 2
10.2.2 Heafding (drawing in) 75O-1OOO-75O 2
10.3 Fabric Production
10.3.1 Knitting 300-50(-750 2
10.3.2 Weaving
10.3.2.1 Jute and hemp 200-300-500 2
10.3.2.2 Heavy woolens 300-500-750 1
10.3.2.3 Medium worsteds, fine woolens, cottons 5OO-75O-1OOO 1
10.3.2.4 Fine worsteds, fine linens, synthetics 75O-1OOO-15OO 1
10.3.2.5 Mending 1000- 15OO-2O(M 1
10.3.2.6 Inspection 100(-1500-2000 1
10.4 Fabric Finishing
10.4.1 Dyeing 200-300-500 3’
10.4.2 Calendaring, chemicaf treatment, etc 300-500-750 2
10.4.3 Inspection
10.4.3.1 ‘Grey’cloth 75O-1OOO-15OO 1
10.4.3.2 Final 1000-1500-2000 1

10.5 Carpet Manufacture


10.5.1 Winding, beaming 200-300-5C0 3
10.5.2 Setting pattern, tnrtlng cropping, trimming, 300-500-750 2
fringing, latexing and latex drying
10.5.3 Designing, weaving, mendksg 5OO-75O-1OOO
10.5.4 Inspection
10.5.4.1 General 750-1000-1500 1 Locaf lighting maybe appropriate
10.5.4.2 Piece dyeing 5OO-75O-1OOO 1 LQcaflighting maybe appropriate

PART 8 BUILDINGSERVICES — SECTION 1 LIGHTING ANDVENTILATION 17


Table 4 — Continued

(1) (2) (3) (4) (5)

11 LEATHER INDUSTRY

11.1 Leather Manufacture


11.1.1 Cleaning, tanning and stretching, vats, cutting, 200-300-500 3
fleshing, stuffing
11.1.2 Finishing, scarfing 300-500-750 2 I

11.2 Leather Working


“

11.2.1 General 200-300-500


11.2.2 Pressing, glazing 300-500-750 2
11.2.3 Cutting, splitting, scarfing, sewing 500-750-1000 2 Directional lighting may be useful.
11.2.4 Grading, matching 2 Local lighting may be appropriate

12 CLOTHING AND FOOTWEAR

12.1 Clothing Manufacture


12.1.1 Preparation of cloth 200-300-500 2
12.1.2 Cutting 500-750-1000 1
12.1.3 Matching 500-750-1000 1
8
12.1.4 Sewing 750-1000-1500 1
12.1.5 Pressing 300-500-750 2
12.1.6 Inspection 1000-1500-2000 1 Local lighting may be appropriate
12.1.7 Hand tailoring 1000-1500-2000 1 Local lighting may be appropriate

12.2 Hosiery and Knitwear Manufacture


12.2.1 Flat bed knitting machines 300-500-750 2
12.2.2 Circular knitting machines 500-750-1000 2
12.2.3 Lockstitch and overlooking machine 750-1000-1500 1
12.2.4 Linking or running on 750-1000-1500 1
12.2.5 Mending, hand finishing 1000-1500-3000 — Local lighting may be appropriate
12.2.6 Inspection 1000-1500-2000 2 Local lighting may be appropriate

12.3 Glove Manufacture


12.3.1 Sorting and grading 500-750-1000 1
12.3.2 Pressing, knitting, cutting 300-500-750 2
12.3.3 Sewing 500-750-1000 2
12.3.4 inspection 1000-1500-2000 — Local lighting may be appropriate

12.4 Hat Manufacture


12.4.1 Stiffening, braiding, refining, forming, sizing, 200-300-500 2 6

pounding, ironing
12.4.2 Cleaning, flanging, finishing 300-500-750 2
12.4.3 Sewing 500-750-1000 2
12.4.4 Inspection 1000-1500-2000 — Local lighting may be appropriate

12.5 Boot and Shoe Manufacture


12.5.1 Leather and synthetics
12.5.2 Sorting and grading 750-1000-1500 1
12.5.3 Clicking, closing 750-1000-1500 2 Local or localized lighting maybe
appropriate
12.5.4 Prepziratory operations 750-1000-1500 2 Local or localized lighting maybe
appropriate
12.5.5 Cutting tables and pressure 1000-1500-2000 1 Local or localized lighting maybe
appropriate
12.5.6 Bottom stock preparation, lasting, bottoming 750-1000-1500 1 Local or localized lighting maybe
finishing, shoe rooms appropriate
12.5.7 Rubber
12.5.7.1 Washing, compounding, coating, drying, 200-300-500 3
varnishing, vulcanizing, calendaring, cutting
12.5.7.2 Lining, making and finishing 300-500-750 2

13 TIMBER AND FURNITURE

13.1 Sawmills
13.1.1 General 150-200-300 3
13.1.2 Head saw 300-500-750 2 Localized lighting may be
appropriate
13.1.3 Grading 500-750-1000 2 Directional lighting may be useful

13.2 Woodwork Shops


13.2.1 Rough sawing, bench work 200-300-500 2

18 NATIONAL BUILDING CODE OF INDIA


Table 4 — Continued

(1) (2) (3) (4) (5)

15.1.1.1 Without manual control 30-50-100 3


15.1.1.2 With occasional manual control 50-100-150 3
15.1.1.3 With continuous manual control 200-300-500 3
15.1.1.4 Control rooms 200-300-500 1
15.1.1.5 Control platforms 200-300-500 2 Local lighting may be appropriate
15.1.2 Non-automatic plant
15.1.2.1 Mixing, calendaring, extrusion, injection, 200-300-500 3
compression and blow moulding, sheet fabrication
15.1.2.2 Trimming, cutting, polishing, cementing 300-500-750 2
15.1.2.3 Printing, inspection 750-1000-1500 1

15.2 Rubber Products


15.2.1 Stock preparation — plasticizing, milling 150-200-300 3
15.2.2 Calendaring, fabric preparation, stock-cutting 300-500-750 3
15.2.3 Extruding, moulding 300-500-750 2
15.2.4 Inspection 750-1000-1500

16 DISTRIBUTION AND STORAGE

16.1 Work Stores 100-150-200 3 Avoid glare to drivers of vehicles


approaching the loading bay
16.1.1 Unpacking, sorting 150-200-300 3 Avoid glare to drivers of vehicles
approaching the loading bay
16.1.2 Large item storage 50-100-150 3 Avoid glare to drivers of vehicles
approaching the loading bay
16.1.3 Small item rack storage 200-300-500 3 Avoid glare to drivers of vehicles
approaching the loading bay
16.1.4 Issue counter, records, storeman’s desk 300-500-750 2 Local or localized lighting maybe
appropriate
16.2 Warehouses and Bulk Stores
16.2.1 Storage of goods where identification requires 50-100-150 3
only limited preparation of detail
16.2.2 Storage of goods where identification requires 100-150-200 3
perception of detail
16.2.3 Automatic high bay rack stores
16.2.3.1 Gangway 20
16.2.3.2 Control station 150-200-300 3
16.2.3.3 Packing and dispatch 200-300-500 3
16.2.3.4 Loading bays 100-150-200 3 Avoid glare to drivers of vehicles
approaching the loading bay
16.3 Cold Stores
16.3.1 General 200-300-500 3
16.3.2 Breakdown, make-up and dispatch 200-300-500 3
16.3.3 Loading bays 100-150-200 3 Avoid glare to drivers of vehicles
approaching the loading bay

17 COMMERCE

17.1 Offices
17.1.1 General offices 300-500-750 1
17.1.2 Deep plan general offices 500-750-1000 1
17.1.3 Computer work stations 300-500-750 1
17.1.4 Conference rooms, executive offices 300-500-750 1
17.1.5 Computer and data preparation rooms 300-500-750 1
171.6 Filing rooms 200-300-500 1

17.2 Drawing Offices


17.2.1 General 300-500-750 1
17.2.2 Drawing boards 500-750-1000 1
17.2.3 Computer aided design and drafting Special lighting is required
17.2.4 Print rooms 200-300-500 1

17.3 Banks and Building Societies


17.3.1 Counter, office area 300-500-750 1
17.3.2 Public area 2oo-3oo-5oo 1

18 SERVICES

18.1 Garages
18S.1 Interior parking areas 20-30-50 3

2(I NATIONAL BUILDING CODE OF INDIA


Table 4 — Continued

(1) (2) (3) (4) (5)

18.1.2 General repairs, servicing, washing, polishing 200-300-500 2


18.1.3 Workbench 300-500-750 1 Local or localized lighting may
be appropriate
18.1.4 Spray booths 300-500-750
18.1.5 External apron
18.1.5.1 General 30-50-100 Care should be taken to avoid
glare to drivers and neightbouring
residents
18.1.5.2 Pump area (retail sales) 200-300-500 See ‘Retailing’

18.2 Appliance servicing


18.2.1 Workshop
18.2.1.1 General 200-300-500 2
18.2.1.2 Workbench 300-500-750 2 Localized lighting may be
appropriate
18.2.1.3 Counter 200-300-500 2 Localized lighting may be
appropriate b

18.2.1.4 Stores 200-300-500 3

18.3 Laundries
18.3.1 Commercial laundries
18.3.2 Receiving, sorting, washing, drying, ironing, 200-300-500 3
despatch, dry-cleaning, bulk machine work
18.3.3 Head ironing, pressing, mending, spotting, 300-500-750 3
inspection
18.3.4 Launderettes 200-300-500 3

18.4 Sewage Treatment Works


18.4.1 Walkways 30-50-100 3
18.4.2 Process areas 50-100-150 3

19 RETAILING
The service illuminance should be
19.1 Small Shops with Counters 300-500-750 provided on the horizontal pkme of
the counter. Where wall displays
19.2 Small Self-Service Shops with Island Displays 300-500-750
are used, a similar illuminance on
the walls is desirable
19.3 Supper Markets, Hyper-Markets
19.3.1 General 300-500-750 2
19.3.2 Checkout 300-500-750 2
19.3.3 Showroom for large objects, for example, cars, 300-500-750 1
furnitures
19.3.4 Shopping precincts and arcades 100-150-200 2

20 PLACES OF PUBLIC ASSEMBLY

20.1 Public Rooms, Village Halls, Worship Halls 200-300-500 1

20.2 Concert Halls, Cinemas and Theatres


20.2.1 Foyer 150-200-300 —
20.2.2 Booking office 200-300-500 — Local or localized lighting may
be appropriate
20.2.3 Auditorium 50-100-150 — Dimming facilities will be
necessary. Special lighting of
the aisles is desirable
20.2.4 Dressing rooms 200-300-500 — Special mirror lighting for
make-up may be required
20.2.5 Projection room 100-150-200 —

20.3 Churches
20.3.1 Body of church 100-150-200 2
20.3.2 Pulpit, lectern 200-300-500 2 Use local lighting
20.3.3 Choir stalls 200-300-500 2 Local lighting may be appropriate
20.3.4 Alter, communion table, chancel 100-150-200 2 Additional lighting to provide
emphasis is desirable
20.3.5 Vestries 100-150-200 2
20.3.6 Organ 200-300-500

20.4 Hospitals
20.4.1 .Anaesthatic rooms

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 21


Table 4 — Continued

(1) (2) (3) (4) (5)

20.4.1.1 General 200-300-500 —


20.4.1.2 Local 750-1000-1500
20.4.2 Consulting areas
20.4.2.1 General 200-300-500
20.4.2.2 Examination 750-1000-1500
20.4.3 Corridors
20.4.3.1 General 100-150-200 —
20.4.4 Ward corridors
20.4.4.1 Day, screened from bays 150-200-300
20.4.4.2 Day, open to natural light 150-200-300
(total)
20.4.4.3 Morning/Evening 100-150-200
20.4.4.4 Night 5-1o
20.4.5 Cubicles
20.4.5.1 General 200-300-500 —
20.4.5.2 Treatment 750-1000-1500 —
20.4.6 Examination
20.4.6.1 General 200-300-500
20.4.6.2 Local inspection 750-1000-1500
20.4.7 Intensive therapy
20.4.7.1 Bad head 30-50
20.4.7.2 Circulation between bed ends 50-100-150 —
20.4.7.3 Observation 200-300-500 —
20.4.7.4 Local observation 750-1000-1500 —
20.4.7.5 Staff base (day) 200-300-500 —
20.4.7.6 Staff base (night) 30 —
20.4.8 Laboratories
20.4.8.1 General 200-300-500
20.4.8.2 Examination 300-500-750
20.4.9 Nurses’ stations
20.4.9.1 Morning/day/evening 200-300-500
20.4.9.2 Night desks 30
20.4.9.3 Night, medical trolleys 50-100-150
20.4.10 Operating theatres
20.4.10.1 General 300-500-750
20.4.10.2 Local 10 000to50000 Special operating lights are used
20.4.11 Pathology departments
20.4.11.1 General ~oo-3(-J()-5()() —
20.4.11.2 Examination 300-500-750 —
20.4.11.3 Pharmacies 200-300-500 —
20.4.11.4 Reception/enquiry 2oo-3oo-5oo .
20.4.11.5 Recovery rooms 2oo-3oo-5oo .
20.4.12 Ward-circulation
20.4.12.1 Day 50-100-150 —
20.4.12.2 MominglEvening 50-100-150 —
20.4.12.3 Night 3-5 —
20.4.13 Ward-bed head
20.4.13.1 Morning/Evening 30-50
20.4.13.2 Reading 100-150-200
20.4.14 Night
20.4.14.1 Adult 0.1-1
20.4.14.2 Pediatric 1
20.4.14.3 Psychiatric 1-5
20.4.14.4 Watch 5
20.4.15 X-Ray areas
20.4.15.1 General 150-200-300
20.4.15.2 Diagnostic 150-200-300
20.4.15.3 Operative 200-300-500
20.4.15.4 Process dark room 50
20.4.16 Surgeries
20.4.16.1 General 200-300-500
20.4.16.2 Waiting rooms 100-150-200
20.4.17 Dental surgeries
20.4.17.1 Chair Special lighting

22 NATIONAL BUILDING CODE OF INDIA


‘r16

Table 4 — Continued

(1) (2) (3) (4) (5)

20.4.17.2
Laboratories 300-500-750
20.4.18 Consulting rooms
20.4.18.1
General 200-300-500 —
20.4.18.2
Desk 300-500-750 —
20.4.18.3
Examination couch 300-500-750 .
20.4.18.4
Ophthalmic wall and near-vision charts 300-500-750 —
20.5 Hotels
20.5.1 Entrance halls 50-100-150
20.5.2 Reception, cashier’s and porters’ desks 200-300-500 Localized lighting may be
appropriate
20.5.3 Bars, coffee base, dining rooms, grill rooms, 50-’200 The lighting should be designed to
restaurants, lounges create an appropriate atmosphere
20.5.4 Cloak rooms, baggage rooms 50-100-150 3
20.5.5 Bed rooms 30-50-100 —- Supplementary local lighting at
the bed head, writing table should
be provided
20.5.6 Bathroom 50-100-150 Supplementary local lighting near
the mirror is desirable
20.5.7 Food preparation and stores, cellars, lifts and See ‘General Building Areas’
corridors

20.6 Libraries
20.6.1 Lending library
20.6.1.1General 200-300-500 1
20.6.1.2Counters 300-500-750 1 Localized lighting may be
appropriate
20.6.1.3Bookshelves 100-150-200 2 The service illuminance should be
provided on the vertical face at
the bottom of the bookstack
20.6.1.4Reading rooms 200-300-500 1
20.6.1.5Reading tables 200-300-500 1 Localized lighting may be
appropriate
20.6.2 Catalogues
?&
20.6.2.1Card 100-150-200 2
20.6.2.2Microfiche/Visual display units 100-150-200 2
20.6.3 Reference libraries
20.6.3.1General 200-300-500 1
20.6.3.2Counters 300-500-750 1 Localized lighting may be
appropriate
20.6.3.3Bookshelves 100-150-200 2 The service illurninance should
be provided on a vertical surface
at the foot of the bookshelves
20.6.3.4Study tables, carrels 300-500-750 1
20.6.3.5Map room 200-300-500 1
20.6.4 Display and exhibition areas
20.6.4.1Exhibits insensitive to light 200-300-500
20.6.4.2Exhibit sensitive to light, for example, pictures, 50 to 150
prints, rare books in archives
20.6.5 Library workrooms
20.6.5.1Book repair and binding 300-500-750 2
20.6.5.2Catalogue and sorting 300-500-750 2
20.6.5.3Remote book stores 100-150-200 3

20.7 Museums and Art Galleries


20.7.1 Exhibits insensitive to light 200-300-500
20.7.2 Light sensitive exhibits, for example, oil and 150 This is a maximum illuminance to
temper paints, undyed leather, bone, ivory, wood, be provided on the principal plane
etc of the exhibit
20.7.3 Extremely light sensitive exhibits, for example, 50 This is the maximum illuminance
textiles, water colours, prints and drawings, skins, to be provided on the principal
botanical specimens, etc plane of the object
20.7.4 Conservation studies and workshops 300-500-750 1

20.8 Sports Facilities

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 23


Table 4 — Continued

(1) (2) (3) (4) (5)

Multi-purpose sports halls 300-750 — This lighting system should be


sufficiently flexible to provide
lighting suitable for the variety of
sports and activities that take place
in sports halls. Higher illurninance
of 1000-2000 lux would be
required for television coverage

21 EDUCATION

21.1 Assembly Halls


21*1.1 General 200-300-500 3
21.1.2 Platform and stage — Special lighting to provide
emphasis and to facilitate the use
of the platform/ stage is desirable
21.2 Teaching Spaces
General 200-300-500 1

21.3 Lecture Theatres


21.3.1 General 200-300-500 1
21.3.2 Demonstration benches 300-500-750 1 Localized lighting may be
appropriate
21.4 Seminar Rooms 300-500-750 1

2L5 Art RoOmS 300-500-750 1

21.6 Needlework Rooms 300-500-750 1

2L7 Laboratones 300-500-750 1

21.8 Libraries 200-300-500 1

21.9 Music Rooms 200-300-500 1


21.10 Sports Halls 200-300-500 1
21.11 Workshops 200-300-500 1

22 TRANSPORT

22.1 Airports
22,1.1 Ticket counters, checking desks, and information 300-500-750 2 Localized lighting may be
desks appropriate
22.1.2 Departure lounges, other waiting areas 150-200-300 2
22.1.3 Baggage reclaim 150-200-300 2
22.1.4 Baggage handling 50-100-150 2
22.1.5 Customs and immigration halls 300-500-750 2
22.1.6 Concourse 150-200-300 2

22.2 Railway Stations


22.2.1 Ticket office 300-500-750 2 Localized lighting may be
appropriate
22.2.2 Information office 300-500-750 2 Localized lighting over the
counter may be appropriate
22.2.3 Parcels office, left
22.2.4 Luggage office
22.2.4.1 General 50-100-150 2
22.2=4.2 Counter 150-200-300 2
22.2.5 Waiting rooms 150-200-300 2
22.2.6 Concourse 150-200-300 2
22.2.7 Time table 150-200-300 2 Localized lighting may be
appropriate
22.2.8 Ticket barriers 150-200-300 2 Localized lighting may be
appropriate
22.2.9 Platforms (covered) 30-50-100 2 Care should be taken to light and
mark the edge of the platform
clearly
22.2.10 Platforms (open) 20 Care should be taken to light and
mark the edge of the platform
clearly

22.3 Coach Stations

24 NATIONAL BUILDING CODE OF INDIA


Table 4 — Concluded

(1) (2) (3) (4) (5)

22.3.1 Ticket offices 300-500-750 2 Localized lighting over the


counter may be appropriate
22.3.2 Information offices 300-500-750 ~ Localized lighting over the
counter may be appropriate
22.3.3 Left luggage office
22.3.3.1General 50-100-150 3
22.3.3.2Counter 150-200-300 3 Localized lighting is appropriate
22.3.4 Waiting rooms 150-200-300 2
22.3.S Concourse 150-200-300 2
22.3.6 Time tables 150-200-300 2 Local lighting is appropriate
~263e7 Loading areas 100-150-200 3

23 GENERAL BUILDING AREAS

23.1 Entrance
23.1.1 Entrance haHs, lobbies, waiting rooms 150-200-300 2
23.1.2 Enquiry desks 300-500-750 2 Localized lighting may be
appropriate
23.1.3 Gatehouses 150-200-300 2

23.2 Circulation Areas


23.2.1 Lifts 50-100-150
23.2.2 Corridors, passageways, stairs 50-100-150 2
23.2.3 Escalators, travellators 100-150-200

23.3 Medical and First Aid Centres


23.3.1 Consulting rooms, treatment rooms 300-500-750 1
23.3.2 Rest rooms 100-150-200 1
23.3.3 Medical stores 100-150-200 2

23.4 Staff Rooms


23.4.1 Changing, locker and cleaners rooms, cloakrooms, 50-100-150
lavatories
23.4.2 Rest rooms 100-150-200 1

23.5 Staff Restaurants


23.5.1 Canteens, cafeterias, dining rooms, mess moms 150-200-300 2 4.

23.5.2 Servery, vegetable preparation, washing-up area 200-300-500 2


23.5.3 Food preparation and cooking 300-500-750 2
23.5.4 Food stores, cellars 100-150-200 2

23.6 Communications
23.6.1 Switchboard rooms 200-300-500 2
23.6.2 Telephone apparatus rooms 100-150-200 2
23.6.3 Telex room, post room 300-500-750 2
23.6.4 Reprographic room 200-300-500 2

23.7 Building Services


23.7.1 Boiler houses
23.7.1.1General 50-100-150 3
23.7.L2 Boiler front 100-150-200 3
23.7.1.3Boiler control room 200-300-500 2 Localized lighting of the control
display and the control desk may
be appropriate
23.7.1.4Control rooms 200-300-500 2 Localized lighting of the control
display and the control desk may
be appropriate
23.7.1.5Mechanical plant room 100-150-200 2
23.7.1.6Electrical power supply and distribution rooms 100-150-200 2
23.7.L7 Store rooms 50-100-150 3

23.8 Car Parks


23.8.1 Covered car parks
23.8.1.1Floors 5-20 —
23.8.1.2Ramps and comers 30 — %
23.8.1.3Entrances and exits 50-100-150 —
23.8.1.4Control booths 150-200-300 —
23.8.1.5Outdoor car parks 5-20 —

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 25


It is important, when lighting stairways, to prevent 4.2 Daylighting
disabili~y from glare ca{sed by direct sight OFbright
The primary source of lighting for daylighting is the
sources to emphasize the edges of the treads and to
sun. The light received by the earth from the sun
avoid confusing shadows. The same precautions should
consists of two parts, namely, direct solar illuminance
be taken in the lighting of cat-walks and stairways on
and sky illuminance. For the purposes of daylighting
outdoor industrial plants.
design, direct solar illuminance shall not be
4.1.5.2 Entrances considered and only sky illuminance shall be taken
as contributing to illumination of the building interiors
The problems of correctly grading the lighting within
during the day.
a building to allow adequate time for adaptation when
passing from one area to another area are particularly 4.2.1 The relative amount of sky illuminance depends
acute at building entrances. These are given below: on the position of the sun defined by its altitude, which
in turn, varies with the latitude of the locality, the day
a) By day, people entering a building will be
of the year and the time of the day, as indicated in
adapted to the very high levels of brightness
Table 5.
usually present outdoors and there is risk of
accident if entrance areas, particularly any 4.2.2 The external available horizontal sky illuminance
steps, are poorly lighted. This problem may (diffuse illuminance) values which are exceeded for
often be overcome by arranging windows about 90 percent of the daytime working hours may
to give adequate natural lighting at the be taken as outdoor design illuminance values for
immediate entrance, grading to lower levels ensuring adequacy of daylighting design. The outdoor
further inside the entrance area. Where this design sky illuminance varies for different climatic
cannot be done, supplementary artificial regions of the country. The recommended design sky
lighting should be installed to raise the level illuminance values are 6800 lux for cold climate,
of illumination to an appropriate value. 8000 lux for composite climate, 9000 lux for warm
b) At night it is desirable to light entrance halls humid climate, 9000 lux for temperate climate and
and lobbies so that the illumination level 10500 for hot-dry climate. For integration with the
reduces towards the exit and so that no bright artificial lighting during daytime working hours an
fittings are in the line of sight of people increase of 500 lux in the recommended sky design
leaving the building. Any entrance steps to illuminance for daylighting is suggested.
the building should be well-lighted by
4.2.3 The daylight factor is dependent on the sky
correctly screened fittings.
luminance distribution, which varies with atmospheric
4.1.6 For detailed information regarding principles of conditions. A clear design sky with its non-uniform
good lighting, reference may be made to good practice distribution of luminance is adopted for the purposes
[8-1(2)]. of design in this section.

Table 5 Solar-Altitudes (to the Nearest Degree) for Indian Latitudes


(Clause 4.2.1)

Period of 22 June 21 March and 23 September 22 December


‘ear ~ /==”. .—”~’
Hours of 0700 0800 0900 1000 11001200 07000800 0900 1000 11001200 07000800 0900 1000 1100 1200
Day (Sun
or Solar)

Latitude 1700 1600 1500 1400 1300 — 1700 1600 1500 1400 1300 — 17001600 1500 1400 1300 —
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (10 (12) (13) (14) (15) (16) (17) (118) (19)
10°N 18 31 45 58 70 77 15 30 44 59 72 80 9 23 35 46 53 57
13°N 19 32 46 60 72 80 15 29 44 58 70 77 8 21 33 43 51 54
16°N 20 33 47 61 74 83 14 29 43 56 68 74 7 19 31 41 48 51
19°N 21 34 48 62 75 86 14 28 42 55 66 71 5 18 29 48 45 48
22°N 22 35 49 62 75 89 14 28 41 53 64 68 4 16 27 36 42 45
25”N 23 36 49 63 76 88 13 27 40 52 61 65 3 14 25 34 39 42
*
28°N 23 36 49 63 76 86 13 26 39 50 59 62 1 13 23 31 37 39
31°N 24 37 50 62 75 82 13 25 37 48 56 56 — 11 21 28 34 36
34°N 25 37 49 62 73 79 12 25 36 46 53 56 — 9 18 26 31 33

26 NATIONAL BUILDING CODE OF INDIA


I

4.2.4 Components of Daylight Factor by a factor equal to the ratio of the clear opening to the
overall opening.
Daylight factor is the sum of all the daylight reaching
on an indoor reference point from the following 4.2.5.3 Correction for glazing
sources:
Where windows are glazed, the sky components
a) The direct sky visible from the point, obtained from Annex A shall be reduced by 10 to 20
b) External surfaces reflecting light directly (see percent, provided the panes are of clear and clean glass.
Note 1) to the point, and Where glass is of the frosted (ground) type, the sky
c) Internal surfaces reflecting and inter- components read from Annex A may be reduced by
reflecting light to the point. 15 to 30 percent. In case of tinted or reflective glass
the reduction is about 50 percent. Higher indicated
NOTES correction corresponds to larger windows and/or near
1 External surface reflection may be computed
reference points. In the case of openings and glazings
approximately only for points at the centre of the room,
and for detailed analysis procedures are complicated which are not vertical, suitable correction shall be taken
and these may be ignored for actual calculations. into account.
2 Each of the three components, when expressed as a
ratio or percent of the simultaneous external ihuninance 4.2.5.4 Correction for external obstructions
on the horizontal plane, defines respectively the sky
There is no separate correction, except that the values
component (SC), the external reflected component
(ERC) and the internal reflected component (IRC) of from tables in Annex A shall be read only for the
the daylight factor. unobstructed portions of the window.
4.2.4.1 The daylight factors on the horizontal plane 4.2.6 External Rejlected Component (ERC)
only are usually taken, as the working plane in a room
The value of the sky component corresponding to the
is generally horizontal; however, the factors in vertical
portion of the window obstructed by the external
planes should also be considered when specifying
obstructions may be found by the use of methods
daylighting values for special cases, such as daylighting
described in Annex B of good practice [8-1(3)].
on class-rooms, blackboards, pictures and paintings
hung on walls. These values when multiplied by the correction factors,
4.2.5 Sky Component (SC) corresponding to the mean elevation of obstruction
from the point in question as given in Table 6, can be
Sky component for a window of any size is computed taken as the external reflected components for that
by the use of the appropriate table of Annex A. point.
a) The recommended sky component level
Table 6 Correction Factor for ERC
should be ensured generally on the working
plane at the following positions: (Clause 4.2.6)
1) at a distance of 3 m to 3.75 m from
Mean Angle of Elevation Correction Factor
the window along the central line
perpendicular to the window, (1) (2)

2) at the centre of the room if more 5° 0.086


15° 0.086
appropriate, and 25° 0.142
3) at fixed locations, such as school desks, 35° 0.192
black-boards and office tables. 45° 0.226
55° 0.274
b) The daylight area of the prescribed sky 65° 0.304
component should not normally be less than 75” 0.324
85° H 0.334
half the total area of the room.

4.2.5.1 The values obtainable from the tables are for 4.2.6.1 For method of calculating ERC, reference may
rectangular, open unglazed windows, with no external be made to accepted standard (see Examples 10 and
obstructions. The values shall be corrected for the 11 given in Annex B of good practice [8-1(3)].
presence of window bars, glazing and external
4.2.7 Internal Reflected Component (IRC)
obstructions, if any. This assumes the maintenance of
a regular cleaning schedule. The component of daylight factor contributed by
reflection from the inside surfaces varies directly as
4.2.5.2 Corrections for window bars
the window area and inversely as the total area of
The corrections for window bars shall be made by internal surfaces, and depends on the reflection factor
multiplying the values read from tables in Annex A of the floor, wall and roof surfaces inside and of the

PART 8 BUILDINGSERVICES— SECTION 1 LIGHTING ANDVENTILATION 27


ground outside. For rooms white-washed on walls and as far as possible, direct sunlight entering the room.
ceiling and windows of normal sizes, the IRC will have CHAJ.JAHS, louvers, etc, reduce the effective height
sizeable value even at points far away from the of the opening for which due allowance shall be made.
window. External obstructions, when present, will Broad and low openings are, in general, much easier
proportionately reduce IRC. Where accurate values of to shade against sunlight entry. Direct sunlight, when
IRC are desired, the same maybe done in accordance it enters, increases the inside illuminance very
with the good practice [8-1(3)]. considerably. Glare will result if it falls on walls at
low angles, more so than when it falls on floors,
4.2.8 General Principles of Openings to Afford Good
especially when the floors are dark coloured or less
Lighting
reflective.
4.2.8.1 Generally, while taller openings give greater
4.2.8.9 Light control media, such as translucent glass
penetrations, broader openings give better distribution
panes (opal or matt) surfaced by grinding, etching or
of light. It is preferable that some area of the sky at sandblasting, configurated or corrugated glass, certain
an altitude of 20° to 25° should light up the working types of prismatic glass, tinted glass and glass blasts
plane. are often used. They should be provided, either fixed
4.2.8.2 Broader openings may also be equally or more or movable outside or inside, especially in the upper
efficient, provided their sills are raised by 300 mm to portions of the openings. The lower portions are usually
600 mm above the working plane. left clear to afford desirable view. The chief purpose
of such fixtures is to reflect part of the light on to the
NOTE — It is to be noted that while placing window with a
roof and thereby increase the diffuse lighting within,
high sill level might help natural lighting, this is likely to reduce
ventilation at work levels. While designing the opening for light up the farther areas in the room and thereby
ventilation also, a compromise may be made by providing the produce a more uniform illumination throughout. They
sill level about 150 mm below the head level of workers. will also prevent the opening causing serious glare
4.2.8.3 For a given penetration, a number of small discomfort to the occupants but will provide some glare
openings properly positioned along the same, adjacent when illuminated by direct sunlight.
or opposite walls will give better distribution of 4.2.9 Availability of Daylight in Multi-storeyedBlock
illumination than a single large opening. The sky
Proper planning and layout of building can add
component at any point, due to a number of openings
appreciably to daylighting illumination inside. Certain
may be easily determined from the corresponding sky
dispositions of building masses offer much less mutual
component contour charts appropriately superposed.
obstruction to daylight than others and have a
The sum of the individual sky component for each
significant relevance, especially when intensive site
opening at the point gives the overall component due
planning is undertaken. The relative availability of
to all the openings. The same charts may also facilitate
daylight in multi-storeyed blocks of different relative
easy drawing of sky component contours due to
orientations are given in Table 7.
multiple openings.
Table 7 Relative Availability of Daylight on the
4.2.8.4 Unilateral lighting from side openings will, in
Window Plane at Ground Level in a Four-
general, be unsatisfactory if the effective width of the
Storeyed Building Blocks (Clear Design-Sky as
room is more than 2 to 2.5 times the distance from the
Basis, Daylight AvailabMty Taken as Unity on
floor to the top of the opening. In such cases provision
an Unobstructed Fagade, Vaiues are for
of light shelves is always advantageous.
the Centre of the Blocks)
4.2.8.5 Openings on two opposite sides will give (Clause 4.2.9)
greater uniformity of internal daylight illumination,
especially when the room is 7 m or more across. They Distance of Infinitely _ ItloclrtJ Par@tel Blocks
Separation Long F@@ Each Facing Gapa
also minimize glare by illuminating the wall surrounding
Between Parallel Between Opposite
each of the opposing openings. Side openings on one Blocks Blwlra E= Blocks @!ngth =
side and clerestory openings on the opposite side may 2 x Ifeight) 2 X Height)
be provided where the situation so requires. (1) (2) “(3) (4)

4.2.8.6 Cross-lighting with openings on adjacent walls 0.5 Ht 0.15 M5 , 0.25


1.0 Ht 0.30 0.32 0.38
tends to increase the diffused lighting within a room. 1.5 Ht 0.40 0.55
2.0 Ht 0.50 $2 0.68
4.2.8.7 Openings in deep reveals tend to minimize
glare effects.
4.2.10 For specified requirements for daylighting of
4.2.8.8 Openings shall be provided with CHAJ.lAHS, special occupancies and areas, reference may be made
louvers, baffles or other shading devices to exclude, to good practice [8-1(4)].

28 NATIONALBUILDINGCODE OF INDIA
4.3 Artificial Lighting amount of calculations, especially if these
tables have to cover a wide range of
4.3.1 Artificial lighting may have to be provided
lighting practices. For every Iuminaire,
a) where the recommended illumination levels the exact light distribution has to be
have to be obtained by artificial lighting only, measured in the laboratory and their
b) to supplement daylighting when the level of efficiencies have to be calculated and
illumination falls below the recommended measured exactly. These measurements
value, and comprise:
c) where visual task may demand a higher level i) the luminous flux radiated by the
of illumination. lurninaires directly to the measuring
surface,
4.3.2 Artificial Lighting Design for Interiors
ii) the luminous flux reflected and re-
For general lighting purposes, the recommended reflected by the ceiling and the walls
practice is to design for a level of illumination on the to the measuring surface, and
working plane on the basis of the recommended levels iii) the inter-reflections between the
for visual tasks given in Table 4 by a method called ceiling and wall which result in
‘Lumen method’. In ot-der to make the necessary the measuring surface receiving
detailed calculations concerning the type and quantity additional luminous flux.
of lighting equipment necessary, advance information All these measurements have to be made for
on the surface reflectance of walls, ceilings and floors different reflection factors of the ceiling and
is required. Similarly, calculations concerning the the walls for all necessary room indices. These
brightness ratio in the interior call for details of the tables have also to indicate the maintenance
interior decor and furnishing. Stepwise guidance factor to be taken for the luminous flux
regarding designing the interior lighting systems for a depreciation throughout the life of an
building using the ‘Lumen method’ is given in 4.3.2.1 installation due to ageing of the lamp and
to 4.3.2.4. owing to the deposition of dirt on the lamps
4.3.2.1 Determination of the illumination level and luminaires and room surfaces.
2) The values of the reflection factor of the
Recommended value of illumination shall be taken
ceiling and of the wall are as follows:
from Table 4, depending upon the type of work to be
White and very light colours 0.7
carried out in the location in question and the visual
tasks involved. Light colours 0.5
Middle tints 0.3
4.3.2.2 Selection of the light sources and luminaires
Dark CO1OLU3 0.1

The selection of light sources and lurninaires depends For the walls, taking into account the
on the choice of lighting system, namely, general influence of the windows without curtains,
lighting, directional lighting and localized or local shelves, almirahs and doors with different
lighting. colours, etc, should be estimated.
4.3.2.3 Determination of the luminous flux c) Calculation for determining the luminous
jlux
a) The luminous flux ($) reaching the working
plane depends upon the following:
1) lumen output of the lamps,
2) type of lurninaire,
or, +$ for new condition
3) proportion of the room (room index) (k,),
4) reflectance of internal surfaces of the E~VA
room, and ~=— for working condition
pd
5) depreciation in the lumen output of the
where
lamps after burning their rated life, and
6) depreciation due to dirt collection on @ = Total luminous flux of the light sources
luminaires and room suface. installed in the room inlumens;
b) Coefficient of Utilization or Utilization Factor E~v = Average illumination level required on the
working plane inlux;
1) The compilation of tables for the
utilization factor requires a considerable A = Area of the working plane in mz;

PART 8 BUILDINGSERVICES — SECTION 1 LIGHTING ANDVENTILATION 29


P = the utilization factor in new conditions; and 4.3.3.3 The need for supplementary lighting during
d = maintenance factor. the day arises, particularly when the daylighting on
the working plane falls below 100 lux and the
In practice, it is easier to calculate straightaway the surrounding luminance drops below 19 cdfm2.
number of lamps or luminaires from:
4.3.3.4 The requirement of supplementary artificial
lighting increases with the decrease in daylighting
availability. Therefore, conditions near sunset or
sunrise or equivalent conditions due to clouds or
.- E.,, A obstructions, etc, represent the worst conditions when
N, -:----- =
LUluu,dll,,
“’
the supplementary lighting is most needed.
where
4.3.3.5 The requirement of supplementary artificial
4= Luminous flux of each lamp in lumens, lighting when daylighting availability becomes poor
Imp
may be determined from Fig. 3 for an assumed ceiling
$,.mi..ij..~
= Luminous flux of each luminaire in
lumens, height of 3.0 m, depending upon floor area, fenestration
percentage and room surface reflectance. Cool daylight
N lamp =
Total number of lamps, and
fluorescent tubes are recommended with semi-direct
N,uminai,e, = Total number of luminaires.
luminaires. To ensure a good distribution of
4.3.2.4 Arrangement of the luminaires illumination, the mounting height should be between
1.5 m and 2.0 m above the work plane for a separation
This is done to achieve better uniformly distributed
of 2.0 m to 3.0 m between the luminaires. Also the
illumination. The location of the luminaires has an
number of lamps should preferably be more in the rear
important effect on the utilization factor.
half of the room than in the vicinity of windows. The
a) In general, luminaires are spaced ‘a’ metre following steps may be followed for using Fig. 3 for
apart in either direction, while the distance of determining the number of fluorescent tubes required
the end luminaire from the wall is ‘Y2 a’ metre. for supplementary daylighting.
The distance ‘a’ is more or less equal to the
a) Determine fenestration percentage of the floor
mounting height ‘Hm’ between the luminaire
area, that is,
and the working plane. The utilization factor
tables are calculated for this arrangement of Window Area ~ ~O.
luminaires. Floor Area
b) For small rooms where the room index (k-) is b) In Fig. 3, refer to the curve corresponding to
less than 1, the distance ‘a’ should always be the percent fenestration determined above
less than H~, since otherwise luminaires and the set of reflectance of ceiling, walls
cannot be properly located. In most cases of and floor actually provided.
such rooms, four or two lurninaires are placed
c) For the referred curve of Fig. 3 read, along
for good general lighting. If, however, in such
the ordinate, the number of 40 W fluorescent
rooms only one luminaire is installed in the
tubes required, corresponding to the given
middle, higher utilization factors are obtained,
floor area on the abscissa.
but the uniformity of distribution is poor. For
such cases, references should be made to the 4.3.4 For detailed information on the design aspects
additional tables for k, = 0.6 to 1.25 for and principles of artificial lighting, reference may be
luminaires located centrally. made to good practice [8-1(2)].
4.3.3 Artificial Lighting to Supplement Daylighting 4.3.5 For specific requirements for lighting of special
occupancies and areas, reference may be made to good
4.3.3.1 The need for general supplementary artificial
practice [8-1(5)].
lighting arises due to diminution
of daylighting beyond
design hours, that is, for solar altitude below 15° or 4.3.6 Electrical installation aspect for artificial lighting
when dark cloudy conditions occur. shall be in accordance with Part 8 ‘Building Services,
4.3.3.2 The need may also arise for providing artificial Section 2 Electrical and Allied Installations’.
lighting during the day in the innermost parts of the
4.4 Energy Conservation in L@ting
building which cannot be adequately provided with
daylighting, or when the outside windows are not of 4.4.1 A substantial portion of the energy consumed
adequate size or when there are unavoidable external on lighting maybe saved by utilization of daylight and
obstructions to the incoming daylighting. rational design of supplementary artificial lights.

30 NATIONALBUILDINGCODE OF INDIA
OPENINGS,
REFLECTANCE

----- ---4
CEILING
07.
07.
WALLS
07.
05.
FLOOR
03.
03.
I 5
PERCENT

—- 0 05. 05. 03
●
00:10
/0 / “’0/00
“

I F
3 o I I I 1
I 1 I f I
i I T I I
I I I I 1
1 I 1 1
z 230
0 50 100 150 200

FLOOR AREA, m 2

FIG. 3 SUPPLEMENTARY
ARTIFICIALLIGHTINGFOR40W FLUORESCENT
TUBES

4.4.2 Daytime use of artificial lights maybe minimized a) An average interior finish with ceiling white,
by proper design of windows for adequate daylight walls off white and floor grey has been
indoors. Daylighting design should be according to 4.2. assumed.
b) Ceiling height of 3 m and room depths up to
4.4.3 Fenestration expressed as percentage of floor
10 m and floor area between 30 m2 and 50 m2
area required for satisfactory visual performance of a
have been assumed. For floor area beyond
few tasks for different separation to height (S/H) ratio
50 m2 and less than 30 m2, the values of
of external obstructions such as opposite buildings may
percent fenestration as well as wattage per m2
be obtained from the design nomograph (Fig. 4). The
should be multiplied by a factor of 0.85 and
obstructions at a distance of three times their height or
1.15 respectively.
more (S/H > 3) from a window faqade are not
c) It is assumed that windows are of metallic
significant and a window facing such an obstruction
sashes with louvers of width up to 600 mm
may be regarded as a case of unobstructed window.
or a CHHAJJA (balcony projection) at ceiling
4.4.3.1 The nomograph consists of horizontal lines level of width up to 2.0 m. For wooden sashes,
indicating fenestration percentage of floor area and the window area should be increased by a
vertical lines indicating the separation to height ratio factor of about 1.1.
of external obstructions such as opposite buildings. d) Luminaires emanating more light in the
Any vertical line for separation to height ratio other downward direction than upward direction
than already shown in the nomograph (1 .0,2.0 and 3 .0) (such as reflectors with or without diffusing
may be drawn by designer, if required. For cases where plastics) and mounted at a height of 1.5 m to
there is no obstruction, the ordinate corresponding to 2.0 m above the workplane have been
the value 3.0 may be used. The value of percentage considered.
fenestration and separation to height ratio are marked
4.4.3.3 Method of use
on left hand ordinate and abscissa respectively. The
illumination levels are marked on the right hand The following steps shall be followed for the use of
ordinate. The values given within brackets are the nomograph:
illumination levels on the work plane at centre and rear
a) Step 1 — Decide the desired illumination level
of the room. The wattage of fluorescent tubes required
depending upon the task illumination
per square metre of the floor area for different requirement in the proposed room and read
illumination levels is shown on each curve. the value of watts per square metre on
4.4.3.2 Following assumptions have been made in the the curve corresponding to the required
construction of the nomograph: illumination level.

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 31


30

28

26
r WATTS PER SQ. m FLOOR AREA
OF SUPPLEMENTAL FLUORESCENT
TUBE LIGHTS 4

$ 24
X
a
u
g 22
-J
IA

(360, 200)
200

(320, 175)
175

(280, 150)
150

(240, 125)
125

(200, 100)
100

(150, 75)
75
1.0 2.0 3.0 ‘-

SEPARATION TO HEIGHT RATIO

FIG. 4 NOMOGRAPHFOR DAYLIGHTINGAND SUPPLEMENTAL


LIGHTINGDESIGN OF BUILDING

b) Step 2 — Fix the vertical line corresponding lights should be increased proportionately
to the given separation to height ratio of to make up for the deficiency of natural
opposite buildings on the abscissa. From the illumination.
point of intersection of this vertical line and
the above curve move along horizontal, and 4.4.4 For good distribution of day light on the working
read the value of fenestration percent on the plane in a room, window height, window width and
left hand ordinate. height of sill should be chosen in accordance with the
following recommendations:
c) Step 3 — If the floor area is greater than
50 mz and less than 30 m2, the value of watts a) In office buildings windows of height 1.2 m
per square metre as well as fenestration or more in the center of a bay with sill level
percent may be easily determined for adequate at 1.0 to 1.2 m above floor and in residential
daylighting and supplemental artificial buildings windows of height 1.0 m to 1.1 m
lighting for design purposes. However, if the with sill height as 0.9 m to 0.7 m above floor
fenestration provided is less than the required are recommended for good distribution
value, the wattage of supplementary artificial of daylight indoors. Window width can

32 NATIONAL BUILDING CODE OF INDIA


accordingly be adjusted depending upon the 4.4.6.1 Eficient ardjicial light sources and lurninaires
required fenestration percentage of the floor
Luminous efficacy of some of the lamps used in
area.
lighting of buildings are given in Table 8 along with
b) If the room depth is more than 10 m, windows average life in burning hours, Colour Rendering Index
should be provided on opposite sides for and Colour Temperature.
bilateral lighting.
Following recommendations may be followed in the
c) It is desirable to have a white finish for ceiling
choice of light sources for different locations:
and off white (light colour) to white for walls.
There is about 7 percent improvement in a) For supplementary artificial lighting of work
lighting levels in changing the finish of walls area in office building care should be taken
from moderate to white. to use fluorescent lamps, which match with
colour temperature of the daylight.
4.4.5 For good distribution and integration of daylight
b) For residential buildings fluorescent lamps
with artificial lights the following guidelines are
and/or CFLS of proper CRI and CCT are
recommended:
recommended to match with the colours and
a) Employ cool daylight fluorescent tubes for interior design of the room.
supplementary artificial lighting. c) For commercial interiors, depending on the
b) Distribute luminaries with a separation of 2 m mounting heights and interior design,
to 3 m in each bay of 3 m to 4 m width. fluorescent lamps, CFLS and low wattage
c) Provide more supplementary lights such as metal halilde lamps are recommended. For
twin tube luminaries in work areas where highlighting the displays in show windows,
daylight is expected to be poor for example hotels, etc, low wattage tubular or dichroic
in the rear region of a room having single reflector type halogen lamps can be used.
window and in the central region of a room d) For industrial lighting, depending on the
having windows on opposite walls. In mounting height and colour consideration
the vicinity of windows only single tube fluorescent lamps, high pressure mercury
luminaries should be provided. vappour lamps or high pressure sodium
vapour lamps are recommended.
4.4.6 Artificial Lighting
4.4.6.2 For the same lumen output, it is possible to
Energy conservation in lighting is effected by reducing
save 75 to 80 percent energy if GLS lamps are replaced
wastage and using energy effective lamps and
with CFL and 65 to 70 percent if replaced with
luminaires without sacrificing lighting quality.
fluorescent lamps. Similar energy effective solutions
Measures to be followed comprise utilization of
are to be chosen for every application area.
daylight, energy effective artificial lighting design by
providing required illumination where needed, turning Similarly with white fluorescent tubes recommended
off artificial lights when not needed, maintaining for corridors and staircases, the electrical consumption
lighter finishes of ceiling, walls and furnishings, and reduces to 1/4.5 of the energy consumption with
implementing periodic schedule for cleaning of incandescent lamps.
luminaires and group replacement of lamps at suitable 4.4.6.3 Efficient luminaire also plays an important
intervals. Choice of light sources with higher luminous role for energy conservation in lighting. The choice
efficacy and luminaires with appropriate light of a luminaire should be such that it is efficient
distribution is the most effective means of energy not only initially but also throughout its life.
saving in lighting. However, choice of light sources Following luminaries are re~ommended for different
also depends on the other lighting quality parameters locations:
like colour rendering index and colour temperature or
a) For offices semi-direct type of luminaries are
appearance. For example, high pressure sodium vapour
recommended so that both the work plane
lamps, which have very high luminous efficacy, are
illumination and surround luminance can be
not suitable for commercial interiors because of poor
effectively enhanced.
colour rendering index and colour appearance, but are
highly desirable in heavy industries. Also the choice b) For corridors and staircases direct type
of light sources depends on the mounting height in the of luminaries with wide spread of light
interiors. For example, fluorescent lamps are not distributions are recommended.
preferred for mounting beyond 7 m height, when high c) In residential buildings, bare fluorescent tubes
pressure gas discharge lamps are preferred because of are recommended. Wherever the incandescent
better optical control due to their compact size. lamps are employed, they should be provided

PART 8 BUILDINGSERVICES— SECTION 1 LIGHTING ANDVENTILATION 33


Table 8 Luminous Efficacy, Life, CRI and CCT of Light Sources
(Clause 4.4.6.1 )

S1 Light Source Efficacy Average Life CRI CCT


No. lm/w h K
(1) (2) (3) (4) (5) (6)

i) Incandescent lamps 8-18 1000 100 2800


GLS 25 W-1 000 W
ii) Tungsten halogen incandescent lamps 10?h higher than 2000 100 2800-3200
Mains-voltage types: comparable CJLS
60 W-2 000 W lamp
Low-voltage types with reflector have
lower wattages
iii) Fluorescent lamps (FI’L)
a) Standard lamps
38 mm (T12)
20 W-65 W
26 mm (T 8)
18 W-58 W
Cool daylight 61 5000 72 6500
Warm white 67 5000 57 3500
b) Tri-Phosper lamps
38 mm (T12)
20 W-65 W 88-104 12000-18000 85-95 2700-6500
26 mm (T 8)
18 W-58 W
iv) Compact Fluorescent Lamps (CFL) 40-80 8000 Similar to
5 W-25 W l?I’L
v) High pressure mercury vapour lamps 36-60 5000 45 4000
80 W-400 W
vi) Blended — Light lamps 11-26 5000 3600
MLL 100 W-500 W
vii) High Pressure Sodium Vapour Lamps 69-130 10000-15000 23 2000
50 w-1 000 w
viii). Metal halide lamtm 69-83 10000 68-92 3000-5600
35 w-2 000 w

NOTES
1 The table includes lamps and wattages currently in use in buildings in India.
2 Luminous efficacy varies with the wattage of the lamp.
3 Average life values are from available Indian Standards. Where Indian Standard is not available, values given are only indicative.
4 CRI and CCT values are only indicative.
5 For exact values, it is advisable to contact manufacturers.

with white enamelled conical reflectors at an off lights even when sufficient daylight is available
inclination of about 45° from vertical. indoors. In offices and commercial buildings, ,*
occupants may switch on lights in the morning and
4.4.7 Cleaning Schedule for Window Panes and
keep them on throughout the day. When sufficient
Luminaires
daylight is available inside, suitable photo controls can
Adequate schedule for cleaning of window panes and be employed to switch off the artificial lights and thus
luminaries will result in significant advantage of prevent the wastage of energy.
enhanced daylight and lumen output from luminaries.
4.4.9 Solar Photovoltaic Systems (SPVJ
This will tend to reduce the duration over which
artificial lights
— will be used and minimize the wastage— Solar photovoltaic system enables direct conversion
of energy. Depending upon the location of the building of sunlight into electricity and is viable option for
a minimum of three to six months interval for periodic lighting purpose in remote nongrid areas. The common
cleaning of luminaries and window panes is SPV lighting systems are:
recommended for maximum utilization of daylight and a) Solar lantern,
artifj cial lights.
b) Fixed type solar home lighting system, and
4.4.8 Photocontrols for Artijlicial Lights c) Street lighting system.
There is a considerable wastage of electrical energy in 4.4.9.1 SPV lighting system should preferably be
lighting of buildings due to carelessness in switching provided with CFL for energy efficiency.

34 NATIONAL BUILDING CODE OF INDIA


f

4.4.9.2 Invertors used in buildings for supplying every worker and for the purpose of that section no
electricity during the power cut period should be account shall be taken of any space in a work room
charged through NW system. which is more than 4.25 m above the floor level.
4.4.9.3 Regular maintenance of SPV system is NOTE — Vitiation of the atmosphere can also occur in factories
necessary for its satisfactory functioning. by odours given off due to contaminants of the product itself,
I
say for example, from tobacco processing in a ‘Bidi’ factory,
Here the ventilation will have to be augmented to keep odours
5 VENTILATION
within unobjectionable levels.
5.1 General
5.2.2.1 Recommended values for air changes
Ventilation of buildings is required to supply fresh air The standards of general ventilation are reeomrnended/
for respiration of occupants, to dilute inside air to prevent based on maintenance of required oxygen, carbon
vitiation by body odours and to remove any products of dioxide and other air quality levels and for the control
combustion or other contaminants in air and to provide of body odours when no products of combustion or
such thermal environments as will assist in the other contaminants are present in the ai~ the values of
maintenance of heat balance of the body in order to air changes should be as follows:
prevent discomfort and injury to health of the occupants.
S1 No. Application Air Change per Hour
5.2 Design Considerations
(1) (2) (3)
I
5.2.1 Respiration
1. Assembly rooms 4-8
Supply of fresh air to provide oxygen for the human 2. Bakeries 20-30
body for elimination of waste products and to maintain 3. Banks/building societies 4-8
\
carbon dioxide concentration in the air within safe 4. Bathrooms 6-10
limits rarely calls for special attention as enough outside 5. Bedrooms 2-4
I air for this purpose normally enters the areas of 6. Billiard rooms 6-8
occupancy through crevices and other openings. 7. Boiler rooms 15-30
8. Cafes and coffee bars 10-12
5.2.1.1 In normal habitable rooms devoid of smoke 9. Canteens 8-12
generating source, the content of carbon dioxide in air 10. Cellars 3-1o
rarely exceeds 0.5 percent to 1 percent and is, therefore, 11. Churches 1-3
incapable of producing any ill effect. The amount of 12. Cinemas and theatres 10-15
air required to keep the concentration down to 1 percent 13. Club rooms 12, Min
is very small. The change in oxygen content is also 14. Compressor rooms 10-12
too small under normal conditions to have any ill 15. Conference rooms 8-12
effects; the oxygen content may vary quite appreciably 16. Dairies 8-12
without noticeable effect, if the carbon dioxide 17. Dance halls 12, Min
concentration is unchanged. 18. Dye works 20-30
19. Electroplating shops 10-12
5.2.2 Vitiation by Body Odours
20. Engine rooms 15-30
Where no products of combustion or other contaminants 21. Entrance halls 3-5
are to be removed from air, the amount of fresh air 22. Factories and work shops 8-10
required for dilution of inside air to prevent vitiation of 23. Foundries 15-30
air by body odours, depends on the air space available 24. Garages 6-8
per person and the degree of physical activity; the 25. Glass houses 25-60
amount of air decreases as the air space available per 26. Gymnasium 6, Min
person increases, and it may vary from 20 m3 to 30 m3 27. Hair dressing saloon 10-15
per person per hour. In rooms occupied by only a small 28. Hospitals-sterlizing 15-25
number of persons such an air change will automatically 29. Hospital-wards 6-8
be attained in cool weather by normal leakage around 30. Hospital domestic 15-20
windows and other openings and this may easily be 31. Laboratories 6-15
secured in warm weather by keeping the openings open. 32. Launderettes 10-15
33. Laundries 10-30
No standards have been laid down under the Factories 34. Lavatories 6-15
Act, 1948 as regards the amount of fresh air required 35. Lecture theatres 5-8
per worker or the number of air changes per hour. 36. Libraries 3-5
Section 16 relating to over-crowding requires that at 37. Living rooms 3-6
least 14 m3 to 16 m3 of space shall be provided for 38. Mushroom houses 6-10

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 35


sweating. Limits of comfort vary considerably according
S1 No. Application Air Change per Hour
to studies carried out in India and abroad. The thermal
(1) (2) (3)
comfort of a person lies between TSI values of 25°C
6-10 and 30°C with optimum condition at 27 .5°C. Air
39. Offices
40. 10-20 movement is necessary in hot and humid weather for
Paint shops (not cellulose)
41. Photo and X-ray dark room 10-15 body cooling. A certain minimum desirable wind speed
42. Public house bars 12, Min is needed for achieving thermal comfort at different
43. Recording control rooms 15-25 temperatures and relative humidities. Such wind speeds
44. Recording studios 10-12 are given in Table 9. These are applicable to sedentary
45. Restaurants 8-12 work in offices and other places having no noticeable
46. Schoolrooms 5-7 sources of heat gain. Where somewhat warmer
47. Shops and supermarkets 8-15 conditions are prevalent, such as in godowns and
48. Shower baths 15-20 machine shops and work is of lighter intensity, and
49. Stores and warehouses 3-6 higher temperatures can be tolerated without much
50. Squash courts 4, Min discomfort, minimum wind speeds for just acceptable
51. Swimming baths 10-15 warm conditions are given in Table 10. For obtaining
52. Toilets 6-10 values of indoor wind speed above 2.0 m/s, mechanical
53, Utility rooms 15-20 means of ventilation may have to be adopted (see also
54. Welding shops 15-30 Part 8 ‘Building Services, Section 3 Air Conditioning,
Heating and Mechanical Ventilation’).
NOTE — The ventilation rates maybe increased by 50 percent
where heavy smoking occurs or if the room is below ground.
Table 9 Desirable Whd Speeds (m/s) for
Thermal Comfort Conditions
5.2.3 Heat Balance of Body
(Clause 5.2.3.1)
Specially in hot weather, when thermal environment
inside the room is worsened by heat given off by Dry Butb Relative Humidity (Percentage)
Temperature, ~
machinery, occupants and other sources, the prime
“c
need for ventilation is to provide such thermal (1) (2) (3) (4) (5) (6) (7) (8)
environment as will assist in the maintenance of heat * * * * * * *
28
balance of the body in order to prevent discomfort and 29 * * * * * 0.06 0.19
injury to health. Excess of heat either from increased 30 * * * 0.06 0.24 0.53 0.85
31 *0.06 0.24 0.53 1.04 1.47 2.10
metabolism due to physical activity of persons or gains
32 0.20 0.46 0.94 1.59 2.26 3.04 **
from a hot environment has to be offset to maintain 33 0.77 1.36 2.12 3.00 ** ** **
normal body temperature (37”C). Heat exchange of 34 1.85 2.72 ** ** ** ** **
35 3.20 ** ** ** ** ** **
the human body with respect to the surroundings is
determined by the temperature and humidity gradient
* None
between the skin and the surroundings and other ** ~g~ thm those aemptable in pracrice.
factors, such as age of persons, clothing, etc, and
the latter depends on air temperature (dry bulb
Table 10 Mti@I Wind Speeds (m/s) for Just
temperature), relative humidity, radiation from the
Acceptable Warm Conditions
solid surroundings and rate of air movement. The
volume of outside air to be circulated through the room (Ckiuse 5.2.3.1)
is, therefore, governed by the physical considerations D& Bulb Relytive Humidity (lkdr%ge)
of controlling the temperature, air distribution or air Temperatssrq / %
movement. Air movement and air distribution may, “c 30 40)4S 060708090
however, be achieved by recirculation of the inside air (1) (2) (3) (4) (5) (6) (7) (8)

rather than bringing in all outside air. However, fresh 28 * * * * * * *


29 * * *****
air supply or the circulated air will reduce heat stress
30*****” *
by dissipating heat from body by evaporation of the 31 * * * * * 0.06 0.23
sweat, particularly when the relative humidity is high 32 * * * O.O9 0.29 0.60 0.94
33 * 0.04 0.24 0.60 1.04 1.85 2.10
and the air temperature is near body temperature.
34 0.15 0.46 0.94 1.60 2.26 3.05 ““
5.2.3.1 Limits of comfort and heat tolerance 35 0.68 1.36 2.10 3.05 ** ** **
36 1.72 2.70 ** *“ ** ““ **
ThermaI comfort is that
condition of thermal environment
under which a person can maintain a body heat balance
at normal body temperature and without perceptible

36 NA’HONAL BUILDING CODE OF INDIA


5.2.3.2 There will be a limit of heat tolerance when c) Mechanical supply and natural exhaust of &,
air temperatures are excessive and the degree of and
physical activity is high. This limit is determined when d) Mechanical supply and mechanical exhaust
the bodily heat balance is upset, that is, when the bodily of air.
heat gain due to conduction, convection and the
radiation from the surroundings exceeds the bo&ly heat 5.3.1 Control ofl-lest
loss, which is mostly by evaporation of sweat from Although it is recognized that general ventilation is
the surface of the body. The limits of heat tolerance one of the most effective methods of improving thermal
for Indian workers are based on the study conducted environmental conditions in factories, in many
by the Chief Adviser Factories, Government of India, situations, the application of ventilation should be
Ministry of Labour and are given in his report on preceded by and considered along with some of the
Thermal Stress in Textile Industry (Report No. 17) following other methods of control. This would
issued in 1956. According to this Report, where facilitate better design of buildings for general
workers in industrial buildings wearing light clothing ventilation, either natural or mechanical or both, and
are expected to do work of moderate severity with the also reduce their cost.
energy expenditure in the range 273 to 284 W, the
maximum wet bulb temperature shall not exceed 29°C 5.3.1.1 Isolation
and adequate air movement subject to a minimum air Sometimes it is possible to locate heat producing
velocity of 30 ndmin shall be provided, and in relation equipment, such as furnaces in such a position as would
to the dry bulb temperature, the wet bulb temperature expose only a small number of workers to hot
of air in the work room, as far as practicable, shall not environment. As far as practicable, such sources of heat
exceed that given in Table 11. in factories should be isolated.
Table 11 Maximum Permissible Wet Bulb In situations where relatively few people are exposed
Temperatures for Given Dry Bulb Temperatures to severe heat stress and their activities are confhed to
(Clause 5.2.3.2) limited areas as in the case of rolling mill operators
and crane operators, it maybe possible to enclose the
Dry Bulb Temperature Maximum Wet-Bulb
work areas and provide spot cooling or supply
‘c Temperature, “C
conditioned air to such enclosures.
(1) (2)

3(I 29.0 5.3.1.2 Insulation


35 28.5
40 28.0 A considerable portion of heat in many factories is due
45 27.5 to the solar radiation falling on the roof surfaces, which,
50 27.0 in turn, radiate heat inside the building. In such
NOTES situations, insulations of the roof or providing a false
1 These are limits beyond which the industry should not atlow ceiling or double roofing would be very effective in
tbe thermal conditions to go for more than 1 h continuously. controlling heat. Some reduction can also be achieved
The limits are based on a series of studies conducted on Indian by painting the roof in heat reflective shades.
subjects in psycbrometric chamber and on other data on beat
casualties in earlier studies conducted in Kolar Gold Fields Hot surfaces of equipment, such as pipes, vessels, etc,
and elsewhere.
in the building should also be insulated to reduce their
2 Figures given in this table are not intended to convey that
human efficiency at 50”C will remain the same as at 30”C, surface temperature.
provided appropriate wet bulb temperatures are maintained.
5.3.L3 Substitution
Efficiency decreases with rise in the dry bulb temperature as
well, as much as possible. Long exposures to temperature of
Sometimes, it is possible to substitute a hot process by
50”C dry bulb/27°C wet bulb may prove dangerous.
a method that involves application of localized or more
3 Refrigeration or some other method of cooling is
recommended in all cases where conditions would be worse efficiently controlled method of heating. Examples
than those shown in this table. include induction hardening instead of conventional
heat treatment, cold riveting or spot welding instead
5.3 Methods of Ventilation of hot riveting, etc.

General ventilation involves providing a building with 5.3.1.4 Radiant shielding


relatively large quantities of outside air in order to
Hot surfaces, such as layers of molten metal emanate
improve general environment of the building. This may
radiant heat, which can best be controlled by placing a
be achieved in one of the following ways:
shield having a highly reflecting surface between the
a) Natural supply and natural exhaust of tic source of heat and the worker, so that a major portion
b) Natural supply and mechanical exhaust of air; of the heat falling on the shield is reflected back to the

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 37


source. Surfaces such as of tin and alurninium have 5.3.2.3 Volume of air required for removing latent
been used as materials for shields. The efficiency of heat
the shield does not depend on its thickness, but on the
If the latent heat gained from the manufacturing
reflectivity and emissivity of its surface. Care should
processes and occupants is also known and a suitable
be taken to see that the shield is not heated up by
value for the allowable rise in the vapour pressure is
conduction and for this purpose adequate provision
assumed:
should be made for the free flow upwards of the heated
air between the hot surface and the shield by leaving 4127.26xK1
the necessary air space and providing opening at the Q,= ~
top and the bottom of the sides.
where
5.3.2 Volume of Air Required
Q, = Quantity of air in m3/h,
The volume of air required shall be calculated by using
K1 = Latent heat gained in W, and
both the sensible heat or latent heat gain as the basis.
The larger of the two figures obtained should be used h = Allowable vapour pressure difference in mm
in actual practice. of mercury.
NOTE — In majority of tie cases, the sensible heat gain
5.3.2.1 Volume of air required for removing sensible will far exceed the latent heat gain, so that the amoun} of
heat outside air to be drawn by ventilating equipment can be
calculated in most cases on the basis of the equation given
When the amount of sensible heat given off by different in 5.3.2.1.
sources, namely, the sun, the manufacturing processes,
machinery, occupants and other sources, is known and 5.3.2.4 Ventilation is also expressed as m31h per mz
a suitable value for the allowable temperature rise is of floor area. This relationship fails to evaluate the
assumed, the volume of outside air to be provided for actual heat relief provided by a ventilation system, but
removing the sensible heat may be calculated from: it does give a relationship which is independent of
building height. This is a more rational approach,
2.9768 K, because, with the same internal load, the same amount
Q,=
t’ of ventilation air, properly applied to the work zone
where with adequate velocity, will provide the desired heat
relief quite independently of the ceiling height of the
Q, = Quantity of air in m3/h,
space, with few exceptions. Ventilation rates of 30 to
K, = Sensible heat gained in W, and
60 m3/h per m2 have been found to give good results
t = Allowable temperature rise in “C. in many plants.
5.3.2.2 Temperature rise refers mainly to the 5.4 Natural Ventilation
difference between the air temperatures at the outlet
(roof exit) and at the inlet openings for outside air. As The rate of ventilation by natural means through
very little data exist on allowable temperature rise windows or other openings depends on:
values for supply of outside air in summer months, the a) direction and velocity of wind outside and
values given in Table 12 related to industrial buildings sizes and disposition of openings (wind
may be used for general guidance. action), and

Table 12 Allowable Temperature Rise Values b) convection effects arising from temperature
of vapour pressure difference (or both)
(Clause 5.3.2.2)
between inside and outside the room and the
Height of Outlet Opening Temperature Rise difference of h~ight between the outlet and
(1) (2) inlet openings (stack effect).
6 3 to 4.5 5.4.1 Ventilation of Non-industrial Buildings
9 4,5 to 6.5
12 6.5 to 11 Ventilation in non-industrial buildings due to stack
NOTES effect, unless there is a significant internal load, could
1 The conditions are limited to light or medium heavy be neglected, except in cold regions, and wind action
manufacturing processes, freedom from radiant heat and inlet may be assumed to be predominant.
openings not more than 3 to 4.5 m above floor level.
2 At the working zone between floor level and 1.5 m above 5.4.1.1 In hot dry regions, the main problem in summer
floor level, the recommended maximum allowable temperature is to provide protection from sun’s heat so as to keep
rise for air is 2°C to 36C above the air temperature at the inlet the indoor temperature lower than those outside under
openings.
the sun. For this purpose windows and other openings

38 NATIONAL BUILDING CODE OF INDIA


are generally kept closed during day time and only recommended levels of occupancy:
minimum ventilation is provided for the control of 1) For sitting on chair 0.75 m,
odours or forremoval ofproducts of combustion. 2) For sitting on bed 0.60 m, and
5.4.1.2 In warm humid regions, theproblem in the 3) For sitting on floor 0.40 m.
design of non-industrid buildings is to provide free iv) Inlet openings should not as far as possible
passage of air to keep the indoor temperature as near be obstructed by adjoining buildings, trees,
to those outside in the shade as possible, and for this sign boards or other obstructions or by
purpose the buildings are oriented to face the direction partitions inside in the path of air flow.
of prevailing winds and windows and other openings
v) In rooms of normal size having identical
are kept open on both windward and leeward sides.
windows on opposite. walls the average indoor
5.4.1.3 In winter months in cold regions, the windows air speed increases rapidly by increasing the
and other openings are generally kept shut, particularly width of window up to two-third of the wall
during night; and ventilation necessary for the control widtly beyond that the increase is in much
of odours and for the removal of products of smaller proportion than the increase of the
combustion can be achieved either by stack action or window width. The air motion in the working
by some infiltration of outside air due to wind action. zone is maximum when window height is
1.1 m. Further increase in window height
5.4.2 Ventilation of Industrial Buildings
promotes air motion at higher level of
In providing natural ventilation of all industrial window, but does not contribute additional
buildings having significant internal heat loads due to benefits as regards air motion in the
manufacturing process, proper consideration should be occupancy zones in buildings.
given to the size and dktribution of windows and other vi) Greatest flow per unit area of openings is
inlet openings in relation to outlet openings so as to obtained by using inlet and outlet openings
give, with due regard to orientation, prevailing of nearby equal areas at the same level.
winds, size and configuration of the building and vii) For a total area of openings (inlet and outlet)
manufacturing processes carried on, maximum of 20 percent to 30 percent of floor area, the
possible control of thermal environment. average indoor wind velocity is around
30 percent of outdoor velocity, Further
5.4.2.1 In the case of industrial buildings wider than
increase in window size increases the
30 m, the ventilation through windows may be
available velocity but not in the same
augmented by roof ventilation.
proportion. In fact, even undermost favorable
5.4.3 Design Guidelines for Natural Ventilation conditions the maximum average indoor
wind speed does not exceed 40 percent of
5.4.3.1 By wind action,
outdoor velocity.
i) A building need not necessarily be oriented viii) Where the direction of wind is quite constant
perpendicular to the prevailing outdoor wind; and dependable, the size of the inlet should
it may be oriented at any convenient angle be kept within 30 to 50 percent of the total
between 0° and 30° without loosing any area of openings and the building should be
beneficial aspect of the breeze. If the oriented perpendicular to the incident wind.
prevailing wind is from East or West, building Where direction of the wind is quite variable
may be oriented at 45° to the incident wind the openings may be arranged so that as far
so as to diminish the solar heat without much as possible there is approximately equal area
reduction in air motion indoors. on all sides. Thus no matter what the wind
ii) Inlet openings in the buildings should be well direction be, there’would be some openings
distributed and should be located on the directly exposed to wind pressure and others
windward side at a low level, and outlet to air suction and effective air movement
openings should be located on the leeward through the building would be assured.
side. Inlet and outlet openings at high levels ix) Windows of living rooms should open directly
may only clear the top air at that level without to an open space. In places where building
producing air movement at the level of sites are restricted, open space may have to
occupancy. be created in the buildings by providing
iii) Maximum air movement at a particular plane adequate courtyards.
is achieved by keeping the sill height if the x) In the case of’ rooms with only one wall
opening at 85 percent of the critical height exposed to outside, provision of two windows
(such as head level) for the following

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTIL, ATION 39


on that wall is preferred to that of a single that in an unobstructed building. To minimix
window. shielding effect, the distances between two
xi) Windows located diagonally opposite to each rows should be 8 H for semi-detached houses
other with the windward window near the and 10 H for long rows houses. However, for
upstream comer give better performance than smaller spacing the shielding effect is also
other window arrangements for most of the diminished by raising the height of the
building orientations. shielded building.
xii) Horizontal louvers, that is a sunshade, atop a xxii) Hedges and shrubs defect the air away from
window deflects the incident wind upward the inlet openings and cause a reduction in
and reduces air motion in the zone of indoor air motion. These elements should not
occupancy. A horizontal slot between the wall be planted at a distance of about 8 m from the
and horizontal louver prevents upward building because the induced air motion is
deflection of air in the interior of rooms. reduced to minimum in that case. However,
Provision of inverted L type (r) louver air motion in the leeward part of the building
increases the room air motion provided that can be enhanced by planting a low hedge at a
the vertical projection does not obstruct the distance of 2 m from the building.
incident wind. xxiii) Trees with large foliage mass having trunk
xiii) Provision of horizontal sashes inclined at an bare of branches up to the top level of
angle of 45° in appropriate direction helps to window, deflect the outdoor wind downwards
promote the indoor air motion. Sashes and promotes air motion in the leeward
projecting outward are more effective than portion of buildings. .-.
projecting inward. xxiv) Ventilation conditions indoors can be
xiv) Air motion at working plane 0.4 m above the ameliorated by constructing buildings on .
floor can be enhanced by 30 percent using a earth mound having a slant surface with a
pelmet type wind deflector. slope of 10° on upstream side.
xv) Roof overhangs help promoting air motion xxv) In case of industrial buildings the window
in the working zone inside buildings. height should be about 1,6 m and width about
xvi) VERANDAH open on three sides is to be two-third of wall width. These should be
preferred since it causes an increase in the located at a height of 1,1 m above the floor.
room air motion for most of the orientations In addition to this, openings around 0.9 m
of the building with respect to the outdoor high should be provided over two-third length
wind. of the glazed area in the roof lights.
xxvi) Height of industrial buildings, although
xvii) A partition placed parallel to the incident wind
determined by the requirements of industrial
has little influence on the pattern of the air
processes involved, generally kept large
flow, but when located perpendicular to the
enough to protect the workers against hot
main flow, the same partition creates a wind
stagnant air below the ceiling as also to dilute
shadow. Provision of a partition with spacing
the concentration of contaminant inside.
of 0.3 m underneath, helps augmenting air
However, if high level openings in roof or
motion near floor level in the leeward
compartment of wide span buildings. walls are provided, building height can be
reduced to 4 m without in any way impairing
xviii) Air motion in a building unit having windows
the ventilation performance.
tangential to the incident wind is accelerated
when another unit is located at end-on NOTE — For data on outdoor wind speeds at a place,
reference may be mide to ‘The Climatic Data Handbook
position on down stream side. prepared by Central Building Research Institute,
xix) Air motion in two wings oriented parallel Roorkee, 1999’.
to the prevailing breeze is promoted by
5.4.3.2 By stack effect
connecting them with a block on downstream
side. Natural ventilation by stack effect occurs when air
xx) Air motion in a building is not affected by inside a building is at a different temperature than air
constructing another building of equal or outside. Thus in heated buildings or in buildings
smaller height on the leeward side; but it is wherein hot processes are carried on and in ordinary
slightly reduced if the leeward building is buildings during summer nights and during
taller than the windward block. premonsoon periods, the inside temperature is higher
xxi) Air motion in a shielded building is less than than that of outside, cool outside air will tend to enter

40 NATIONAL BUILDING CODE OF INDIA


through openings at low level and warm air will tend fr = Average temperature of indoor air at height
to leave through openings at high level. It would, h in “C; and

therefore, be advantageous to provide ventilators as to = Temperature of outdoor air in “C.


close to ceilings as possible. Ventilators can also be NOTE — The equation is based on 0.65 effectiveness of
provided in roofs as, for example, cowl, ventpipe, openings. This should be reduced to 0.50 if conditions are not
covered roof and ridge vent. favorable.

5.6.1.3 When areas of inlet and outlet openings are


5.5 Mechanical Ventilation
unequal, the value of A may be calculated using the
The requirements of mechanical ventilation shall equation
be in accordance with Part 8 ‘Building Services, 2 1 1
Section 3 Air Conditioning, Heating and Mechanical —= +
Ventilation’. A2 A:let A:utlet

5.6.1.4 When both forces (wind and thermal) act


5.6 Determining Rate of Ventilation
together in the same direction, even without
5.6.1 Natural Ventilation interference, the resulting air flow is not equal to the
two flows estimated separately. Flow through any
This is difficult to measure as it varies from time-to-
opening is proportional to the square root of the sum
time. The amount of outside air through windows and
of the two heads acting on that opening.
other openings depends on the direction and velocity
of wind outside (wind action) and/or convection Wind velocity and direction, outdoor temperature, and
effects arising from temperature or vapour pressure indoor distribution can not be predicted with certainty,
differences (or both) between inside and outside of the and refinement in calculation is not justified. A simple
building (stack effect’). method is calculate the sum of the flows produced by
each force separately. Then using the ratio of the flow
5.6.1.1 Wind action
produced by thermal forces to the aforementioned sum,
For determining the rate of ventilation based on wind the actual flow due to the combined forces can be
action the wind may be assumed to come from any approximated from Fig. 5. When the two flows are
direction within 45° of the direction of prevailing wind. equal, the actual flow is about 30 percent greater than
Ventilation due to external wind is given by the the flow caused by either force acting independently
following formula: (see Fig. 5).

Q=KAV 4.

where

Q = Rate of air flow in m3/h;


K = Coefficient of effectiveness, which maybe
taken as 0.6 for wind perpendicular to
openings and 0.3 for wind at an angle less
than 45° to the openings;
A = Free area of inlet openings in m2; and
v = Wind speed in ndh.
NOTE — For wind data at a place, the local Meteorological
Department may be consulted.

5.6.1.2 Stack effect

Ventilation due to convection effects arising from ‘O 20 40 60 80 100


temperature difference between inside and outside is
FLOW DUE TO TEMPERATURE
given by: DIFFERENCE AS PERCENT OF TOTAL

FIG. 5 DETERMINATIONOF FLOW CAUSED


BY COMBINEDFORCES OF WIND AND TEMPERATURE
where DIFFERENCE
Q = Rate of air flow in m31h;
Judgement is necessary for proper location of openings
A = Free area of inlet openings in m2; in a building specially in the roof, where heat, smoke
h = Vertical distance between inlets and outlets and fumes are to be removed. Usually, windward
in m; monitor openings should be closed, but if wind is so

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 41


slight that temperature head can overcome it, all 5.7 Energy Conservation in Ventilation System
openings may be opened.
5.7.1 Maximum possible use should be made of wind
5.6.1.5 For method for determining the rate of induced natural ventilation. This may be accomplished
ventilation based on probable indoor wind speed by following the design guidelines given in 5.7.1.1.
with typical illustrative example for residential
5.7.1.1 Adequate number of circulating fans should be
building, reference may be made to good practice
installed to serve all interior working areas during summer
[8-1(6)].
months in the hot dry and warm humid regions to provide
5.6.2 Mechanical Ventilation necessary air movement at times when ventilation due to
wind action alone does not afford sufficient relief.
The determination of rate of ventilation in case of
mechanical ventilation shall be done in accordance 5.7.1.1.1 The capacity of a ceiling fan to meet the
with Part 8 ‘Building Services, Section 3 Air requirement of a room with the longer dimension D
Conditioning, Heating and Mechanical Ventilation’. metres should be about 55 D m3/min.
5.7.1.1.2 The height of fan blades above the floor
5.6.3 Combined Effect of Different Methods of
should be (3H + W)/4, where H is the height of the
Ventilation
room, and W is the height of work plane.
When combination of two or more methods of general
5.7.1.1.3 The minimum distance between fan blades
ventilation is used, the total rate of ventilation shall be
and the ceiling should be about 0.3 metre.
reckoned as the highest of the following three, and this
rule shall be followed until an exact formula is 5.7.2 Electronic regulators should be used instead of
established by research: resistance type regulators for controlling the speed of fans. —

a) 1.25 times the rate of natural ventilation, 5.7.3 When actual ventilated zone does not cover the
b) Rate of positive ventilation, and entire room area, then optimum size of ceiling fan
should be chosen based on the actual usable area of
c) Rate of exhaust of air.
room, rather than the total floor area of the room. Thus
5.6.4 Air Movement smaller size of fan can be employed and energy saving
could be achieved.
The rate of air movement of turbulent type at the
working zone shall be measured either with a Kata 5.7.4 Power consumption by larger fans is obviously
thermometer (dry silvered type) or heated thermometer higher, but their power consumption per square metre
or properly calibrated thermocouple anemometer. of floor area is less and service value higher. Evidently,
Whereas anemometer gives the air velocity directly, improper use of fans irrespective of the rooms
the Kata thermometer and heated thermometer give dimensions is likely to result in higher power
cooling power of air and the rate of air movement is consumption. From the point of view of energy
found by reference to a suitable nomogram using the consumption, the number of fans and the optimum sizes
ambient temperature. for rooms of different dimensions are given in Table 13.

Table 13 Optimum Size/Number of Fans for Rooms of DMerent tW.es


(Clause 5.7.4)

Room Room Length


Width - .
e
m 4m 5m 6m 7m 8m 9m 10 m llm . 12 m 14 m 16 m
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12)
3 1 200/1 1 400/1 1 500/1 1 050/2 1 200/2 1 400/2 1 400/2 1 400/2 f 1200/3 1 40W3 1 400/3
4 1 200/1 1 400/1 1 200/2 1 200/2 1 200/2 1 400/2 1 400/2 1 500/2 1 200/3 1 400/3 150013
5 1 400/1 1 400/1 1400/2 1 400/2 1 400/2 1 400/2 1 400f2 1 500/2 1 400/3 1 400/3 150013
6 1 200/2 1 400/2 900/4 1 050/4 1 200/4 1 400/4 1 400/4 1 500/4 1 200/6 1 400/6 1 500/6
7 1 200/2 1 400/2 1 050/4 1 050/4 1 200/4 1 400/4 140014 1 500/4 1 200/6 1 400/6 1 500/6
8 1 200/2 1 400/2 120014 1 200/4 1 200/4 1 400/4 1 400/4 1 500/4 1200/6 1 400/6 1 500/6
9 1 400/2 1 400/2 1 400/4 1 400/4 1 400/4 1 400/4 1 400/4 1 500/4 1400/6 1 400/6 1 500/6
10 1400/2 140012 1 400/4 1 400/4 1 400/4 1 400/4 1 400/4 1 500[4 1400/6 1400/6 1 500/6
11 1500/2 150012 1 500/4 1 500/4 1 500/4 1 500/4 1 500/4 1 500/4 1500/6 1500/6 1 500/6
12 1 200/3 1 400/3 1200/6 1 200/6 1 200/6 1400/6 140016 1 500/6 1 200/7 1 400/9 1 400/9
13 1 400/3 1 400/3 1200/6 1 200/6 1 200/6 1 400/6 1400/6 150016 1 400/9 1 400/9 1 500/9
14 1 400/3 1 400/3 1400/6 1 400/6 1400/6 1400/6 1 400/6 1 500/6 1 400/9 1 400/9 1 500/9

42 NATIONAL BUILDING CODE OF INDIA


ANNEX A
(Clauses 4.2.5,4 .2.5.2,4.2.5.3 and 4.2.5.4)
SKY COMPONENT TABLES

A-1 DESCRIPTION OF TABLES component at given point is explained with help of the
following example.
A-L1 The three sky component tables are as given
below: A-L6.2 Example

Table 14 Percentage sky components on the It is desired to calculate the sky component due to a
horizontal plane due to a vertical vertical window ABCD with width 1.8 m and height
rectangular opening for the clear 1.5 mat a point P on a horizontal plane 3.0 m from the
design sky window wall located as shown in Fig. 7. Foot of the
Table15 Percentage sky components on the perpendicular N is 0.6 m below the sill and 0.9 m to
vertical plane perpendicular to a ;he”left of AD.
vertical rectangular opening for the 1.8m
-
cleardesign sky
D D c
Table 16 Percentage sky components on the
vertical plane parallel to a vertical
E
Iq
rectangular opening for the clear
design sky
B
A-1.2 All the tables are for an unglazed opening A’ A

illuminatedby the clear design sky. {E ~

A-1.3 The values tabulated are the components ata


point~distantfrom theopeningona lineperpendicular
to the plane of the opening through one of its lower
corners, and 1 and h are the width and height
~espectively of the rectangular opening (see Fig. 6). ‘v’
Fm. 7
I
Consider ABCD extended to NB’ CD’
1) For NB’CD”
lid = (1.8+ 0.9)/3= 0.9
hfd = (L5 + 0.6)/3 = 0.7
F1 = 5.708 percent (from Table 15)
2) For NA’DD’
lld = 0.9/3= 0.3
hfd = (1.5+ 0.6)/3= 0.7
F2 = 2.441 percent (from Table 15)
3) For NB’BA’
lld = (1.8+ 0.9)/3= 0.9
FIG. 6
hfd = 0.6/3 = 0.2
A-L4 Sky component for different h/d and Z/d values F~ = 0.878 percent (from Table 15)
are tabulated, that is, for windows of different size and 4) For NA ‘AA’
for different distances of the point P from the window.
lld = 0.9/3 = 0.3
A-1.5 By suitable combination of the values obtained hld = 0.6/3 = 0.2
from the three tables, for a given point for a given Fd = 0.403 percent (from Table 15)
window, the sky component in any plane passing
through the point may be obtained. Since ABCD = NB”CD”–NA”DD’-NB ’BA’+NA%A”
Sky Component F = F1–Fz–F~+Fa
A- L6 Method of Using the Tables = 5.708-2.441-0.878+0.403
A-1.6.1 Method of using the Tables to get the sky = 2.792

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 43


A
a Table 14 Percentage Sky Components on the Horizontal Plane Due to a Verticle Rectangular
Opeining for the Clear Design Sky
(Clause A-1.5)

U(j+ 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1,9 2.0 3.0 4.0 5.0 10.0 INF
Wd
+
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26)

0.1 0.036 0.071 0.104 0.133 0.158 0.179 0.198 0.213 0.225 0.235 0.243 0.250 0.256 0.261 0.264 0.268 0.270 0.272 0.274 0.276 0.284 0.286 0.287 0.288 0.288
0.2 0.141 0.277 0.403 0.516 0.614 0.699 0.770 0.829 0.878 0.918 0.950 0.977 0.999 1.018 1.033 1.046 1.056 1.065 1.072 1.079 1.110 1.118 1.122 1.125 1.125
0.3 0.300 0.589 0.859 1.102 1.315 1.499 1.653 1.782 1.888 1.976 2.0$8 2.108 2.157 2.197 2.231 2.259 2.282 2.302 2.318 2.333 2.44N 2.421 2.429 2.436 2.437
0.4 0.460 0.905 1.322 1.702 2.041 2.337 2.590 2.804 2.984 3.134 3.258 3.361 3.446 3.516 3.574 3.623 3.664 3.699 3.728 3.753 3.873 3.909 3.922 3.935 3.937
0.5 0.604 1.189 1.741 2.247 2.700 3.099 3.444 3.740 3.992 4.204 3.383 4.553 4.659 4.765 4.853 4.928 4.990 5.043 5.088 5.126 5.312 5.366 5.387 5.408 5.410
0.6 0.732 1.443 2.114 2.732 3.289 3.781 4.211 4.582 4.900 5.171 5.401 5.5% 5.761 5.901 6.020 6.121 6.208 6.281 6.344 6.397 6.661 6.739 6.769 6.798 6.802
0.7 0.844 1.665 2.441 3.159 3.808 4.385 4.891 5.330 5.708 6.034 6.311 6.548 6.751 6.924 7.071 7.198 7.307 7.400 7.481 7.551 7.902 8.0&5 8.047 8.087 8.092
0.8 0.942 1.858 2.727 3.532 4.262 4.914 5.488 5.989 6.423 6.798 7.119 7.395 7.632 7.836 8.011 8.162 8.292 8.405 8.502 8.587 9.029 9.164 9.217 9.268 9.276
0.9 1.026 2.025 2.974 3.855 4.657 5.375 6.011 6.567 7.051 7.470 7.832 8.144 8.413 8.645 8.846 9.019 9.170 9.301 9.415 9.515 10.045 10.214 10.280 10.345 10.355
1.0 1.099 2.169 3.188 4.135 5.000 5.776 6.465 7.071 7.600 8.060 8.458 8.803 9.102 9.361 9.585 9.780 9.950 10.098 10.228 10.343 10.957 11.162 11.243 11.323 11.335
1.1 1.161 2.294 3.372 4.377 5.2% 6.124 6.861 7.510 8.079 8.576 9.008 9.383 9.709 9.992 10.239 10.454 10.642 10.806 10.951 11.078 11.776 12.017 12.114 12.209 12.224
1.2 1.215 2.401 3.531 4.586 5.553 6.425 7.204 7.893 8.498 9.027 9.489 9.892 10.243 10.549 10.816 11.050 11.254 11.434 11.593 11.732 12.509 12.786 12.900 13.013 13.030
1.3 1.262 2.493 3.668 4.767 5.775 6.687 7.503 8.226 8.863 9.422 9.912 10.339 10.713 11.040 11.326 11.577 11.797 11.992 12.163 12.314 13.167 13.478 13.609 13.742 13.762
1.4 1.302 2.573 3.787 4.924 5.968 6.915 7.764 8.517 9.183 9.769 10.283 10.733 11.127 11.473 11.777 12.044 12.279 12.487 12.670 12.833 13.758 14.102 14.251 14.404 14.427
1.5 1.337 2.643 3.891 5&0 6.136 7.114 7.991 8.772 9.664 10.073 10.609 11.080 11.493 11.857 12.176 12458 12.707 12.927 13.122 13.295,, 14.289 14.666 14.832 15.006 15.033
1.6 1.367 2.703 3.981 5.179 6.283 7.2S7 8.190 8.996 9.710 10.341 10.897 11.386 11.817 12.1% 12.531 12826 13.W8 13.319 13.525 13.708 14.768 15.176 15.359 15.555 15.585
z
1.7 1.394 2.756 4.O@ 5.283 6.412 7.440 8.366 9.192 9.927 10.577 11.151 11.657 12.104 12.498 12.846 13.154 13.427 13.669 13.885 14.078 15.199 15.638 15.838 16.056 16.091
~ 1.8 1.417 2.8Q3 “4.129 5.375 6.526 7.574 8.520 9.3$6 10.119 10.786 11.376 11.898 12.359 12.766 13.127 13.446 ‘13.730 13.983 14.208 14.409 15.590 16.058 16.274 16.516 16.554
1.9 1.438 ‘2.844 4.1* 5.456 6.626 .(?.% ‘8.656 9.52o 10.289 10.972 11.577 12.112 12.587 13.m 13.378 13.~ 14.~ 14.264 14.498 14.707 15944 16441 16.673 16937 16.980
:
w 2.0 1.456 2.8804.244 5.$27 6.714 ~798 8.778 9.656 10.440 11.137 11.755 12.303 12.789 13.220 13.@3 13.943 14.246 14.516 14.758 14.975 16.265 16.790 17.037 17.325 17.372
8 3.0 1.559 3.087 4.5S3 5.937 7.223 8.403 9.478 10.448 11.321 12.103 12804 13.431 13.993 14.4% 14.947 15.333 ‘15.718 16.048 16.346 16.676 18.301 19.051 19.432 19.943 20.046

E 4.0 1.600 3.168 4.676 6.100 7.426 8.646 9.759 10.768 11.678 12.498 13.235 13.897 14.493 15.030 15.514 15.%1 16.347 16.706 17.033 17.330 19.241 20.142 20.623 21.322 21.495
a 5.0 1.620 3.208 4.735 6.179 7.525 8.763 9.897 10.925 11.854 12.693 13.448 14.128 14.742 15.296 15.798 16.252 16.664 17.040 17.382 17.695 19.740 20.740 21.293 22.148 22.393
g 10.0 1.648 3.263 4.818 6.289 7.662 8.930 10.089 11.144 12.100 12965 13.747 14.454 15.094 15.674 16.201 16.681 17.118 17.518 17.885 18.222 20.491 21.681 22.390 23.676 24.238
m
g INF 1.657 3.282 4.846 6.327 7.710 8.986 10.155 11.220 12.186 13.060 13.851 14.567 15.217 15.806 16.342 16.831 17.278 17.688 18.054 18.41O 20.770 22.o46 22.838 24.463 26.111

%
s

.*P ._
I -“y
Table 15 Percentwe Sky Components on the Vertical Plane Perpendicular to a
Vertimi Rec-tindul& Opening for the C1ear Design Sky
(Clauses A-1.5 and A-1 .6.2)

Ud+ 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 3.0 4.0 5.0 10.0 m
d
Y
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26)

0.1 0.036 0.141 0.303 0.5W5 0.734 0.97i 1.207 1.432 1.643 2.836 1:011 2.168 2.308 2.433 2.544 2.642 2.730 2.808 2.878 2.940 3.309 3.461 3.536 3.641 3.678
0.2 0.071 0.277 0.594 0.993 1.442 1.910 2.374 2.820 3.236 3.618 3.964 4.276 4.554 4.802 5.022 5.219 5.393 5.549 5.688 5.812 6547 6.850 7.CKKI 7.211 7.284
0.3 0.103 0.401 0.863 1.445 2.100 2.793 3.475 4.180 4.743 5.306 5.818 6.278 6.690 7.058 7.385 7.677 7.936 8.168 8.375 8.560 9.657 10.110 10.335 10.651 10.760
0.4 0.126 0.491 1.059 1.779 2.597 3.460 4.326 5.166 5.958 6.691 7.359 7.%7 8.507 8.9(M 9.420 9.804 10.146 10.451 10.724 10.%8 12.421 13.024 13.323 13.743 13.889
0.5 0.142 0.554 1.197 2.015 2.947 3.937 4.938 5.914 6.842 7.707 8.583 9.228 9.883 10.472 10.999 11.476 11.897 12.273 12.610 12.912 14.712 15.462 15.835 16.360 16542
0.6 0.154 0.600 1.298 2.187 3.204 4.288 5.389 6.468 7.498 8.464 9.358 10.177 10.922 11.5% 12.204 12.752 13.244 13.686 14.084 14.441 16.583 17.478 17.924 18.552 18.771
0.7 0.162 0.634 1.372 2.316 3.397 4.552 5.729 6.887 7.997 9.042 10.013 10.907 11.723 12.465 13.138 13.746 14.296 14.793 15.241 15.646 18.111 19.148 19.665 20.397 20.653
0.8 0.169 0.660 1.429 2.413 3543 4.754 5.990 7.209 8.382 9.490 10.523 11.476 12.350 13.147 13.873 14.531 15.129 15.670 16.161 16.6Q6 19.361 20538 21.127 21.%1 22.253
0.9 0.174 0.680 1.472 2.487 3.655 4.9o9 6.192 7.460 8.683 9.841 10.924 11.926 12.847 13.690 14.459 15.159 15.796 16.375 16.902 17.38$ 20.387 21.701 22.360 23.397 23.625
1.0 0.178 0.695 1.505 2545 3.743 5.030 6.350 7.657 8.921 10.120 11.243 12.284 13.245 14.126 14.931 15.666 16.337 16.948 17,504 18.012 21.237 22.680 23.408 24.446 24.810
1.1 0.181 0.707 1.532 2.591 3.812 5.126 6.475 7.814 9.110 10342 11.498 12.573 13.356 14.478 15.314 16.079 16.778 17.416 17999 18.531 21.946 23.508 24.303 25.441 25.841
1.2 0.183 0.716 1.552 2.626 3.866 5.202 6575 7.939 9.261 10.521 11.705 12.807 13.827 14.766 15.628 16.418 17.141 17.802 18.407 18.%1 22543 24.208 25.072 26309 26.745
1.3 0.185 0.723 1.568 2.655 3.910 5.263 6.655 8.040 9.384 10.666 11.873 12.998 14.041 15.003 15.887 16.698 17.442 18.123 18.747 19.320 23.U49 24.809 25.735 27.070 27542
1.4 0.186 0.729 1.582 2.678 3.945 5.312 6.720 8.122 9.484 10.785 12.011 13.155 14.217 15,198 16.101 16.931 17.692 18.391 19.032 19.621 23.480 25.326 26308 27.441 28.249
15 0.188 0.734 1.592 2.697 3.973 5.352 6.773 8.189 9566 10.883 12.124 13.285 14364 15361 16.280 17.125 17.902 18.616 19.272 19.875 ~~
23.850 25.772 26.808 28336 28.880
1.6 0.189 0.738 1.601 2.712 3.996 5.385 6.816 8.244 9.634 10.%3 12.219 13.394 14.486 15.497 16.430 17.289 18.079 18.806 19.475 20.090 24.169 26.161 27.245 28.866 29.445
1.7 0.189 0.741 1.608 2724 4.016 5.412 6.852 8.290 9.690 11.031 12.298 13.484 14389 15.511 16556 17.427 18.229 18.%8 19.648 20274 24.444 26.501 27.629 29340 29.955
1.8 0.190 0.744 1.614 2.735 4.032 5.434 6.882 8.328 9.737 11.087 12364 13.561 14.675 15.7@ 16.663 17545 18.357 19.105 19.795 20.431 24.684 26.799 27.969 29.765 30.416
1.9 0.191 0.746 1.619 2743 4.045“’&453 ‘6.90$ 8.360 9.777 11.135 12.420 13.625 14.749 15.791 16.755 17.645 18.466 19.224 19.922 20.%7 24.893 27.062 28.270 30.149 30.835
2,0 0.191 0.748 1.623 2.751 4.056 5.469 6.929 8.387 9.811 11.175 12.468 13.684314.811 15.861 16.833 17.731 18560 19.325 20.031 20.684 25.077 27.294 28.537 30.4% 31.217
3.0 0.193 0.756 1.642 2.785 4.109 5.544 7.030 8.517 9.972 11.371 12.699 13.950 15.120 16.211 17.224 18.164 19.036 19.844 20.594 21.289 26.082 28.619 30.108 32.676 32.742
4.0 0.194 0.759 1.648 2794 4.124 5566 7.058 8540 10.018 11.427 12767 14.029 15.212 16.316 17343 18.298 19.185 20.~8 20.772 21.483 26.439 29.128 30.745 33.687 35.064
5.0 0.194 0.760 1.650 2798 4.129 5574 7.fM9 8.568 10.036 11.449 12.793 14.060 15.248 16.357 17.390 18.351 19.243 20.073 20.844 21562 26.592 29359 31.049 34.232 35.872
10.0 0.194 0.761 1.652 2.801 4.135 5.581 7.080 8.582 10.053 11.470 12.818 14.095 15.283 16.398 17.436 18.403 19.302 20.138 20.917 21.641 26.758 29.624 31.419 35.049 37513
INF 0.194 0.761 1.652 2.802 4.136 5.582 7.081 8584 10.056 11.473 12.822 14.095 15.%8 16.404 17.443 18.411 19.311 20.148 20.928 21.654 26.785 29.672 31.490 35.274 39.172
Table M Percentage Sky Components on the Vertical Plane Parallel to a
Vertical Rectangular Opening for the Clear Design Sky
(Clause A-1 .5)

1/’+ 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 3.0 4.0 5.0 10.0 INF
h/d
+
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26)

0.1 0.728 1.429 2.078 2.600 3.167 3.660 3.964 4.265 4.513 4.717 4.883 5.020 5.132 5.225 5.301 5.365 5.418 5.463 5.501 5.533 5.687 5.733 5.749 5.765 5.766
0.2 1.429 2.803 4.007 5.221 6.220 7.073 7.790 8.385 8.876 9.278 9.609 9.880 10.103 10.286 10.439 10.565 10.671 10.760 10.835 10.899 11.207 11.296 11.330 11.362 11.365
0.3 2.068 4.061 5.913 7.580 9.040 10.285 11.337 12.212 12.934 13.528 14.016 14.417 14.747 15.020 15.246 15.434 15.591 15.724 15.836 15.931 16.390 16.523 16.574 16.623 16.627
0.4 2.529 4.970 7.249 9.312 11.133 12.707 14.042 15.164 16.097 16.870 17.507 18.025 18.458 18.816 19.113 19.360 19.568 19.742 19.890 20.015 20.624 20.801 20.868 20.933 20,939
0.5 2.852 5.608 8.186 10.529 12.606 14.401 15.952 17.256 18.350 19.262 20.021 20.652 21.177 21.613 21.978 22.275 22.530 22.746 22.923 23.082 23.836 24.056 24.140 24.222 24.229
0.6 3.086 6.070 8.867 11.415 13.681 15.656 17.353 18.793 20.008 21.027 21.879 22.592 23.189 23.689 24.109 24.462 24.761 25.014 25.229 25,412 26.229 26.561 26.662 26.759 26.768
0.7 3.259 6.413 9.373 12.074 14.482 16.588 18.402 19.949 21.257 22.359 23.285 24.063 24.716 25.267 25.731 26.124 26.458 26.742 26.984 27.192 28.214 28.517 28.634 28.748 28.75S
0.8 3.389 6.672 9.755 12.573 15.090 17.296 19.201 20.830 22.212 23.380 24.365 25.195 25.895 26.486 26.987 27.412 27.775 28.084 28.350 28.578 29.720 30.065 30.198 30.327 30.339
0.9 3.489 6.869 10.046 12.955 15.556 17.840 19.817 21.511 22.952 24.173 25.206 26.078 26.816 27.441 27.972 28.424 28.810 29.141 29.426 29.672 30.927 31.303 31.451 31.596 31.610
1.0 3.565 7.024 10.272 13.250 15.917 18.263 20.297 22.043 23.531 24.795 25.866 26.773 27.542 28.196 28.572 29.226 29.633 29.982 30.283 30.544 31.889 32.302 32.467 32.627 32.643
1.1 3.625 7.139 10.447 13.481 16.200 18.594 20.674 22.462 23.989 25.288 26.391 27.326 28.121 28.798 29.375 29.869 30.293 30.658 30.973 31.246 32.670 33.117 33.297 33.473 33.49!
1.2 3.672 7.233 10.586 13.663 16.423 18.857 20.973 22.795 24.353 25.681 26.810 27.770 28.587 29.283 29.878 30.388 30.826 31.204 31.532 31.816 33.309 33.796 33.981 34.173 34.193
1.3 3.709 7.307 10.696 13.807 16.602 19.067 21.213 23.062 24.646 25.998 27.148 28.128 28.963 29.676 30.286 30.810 31.261 31.651 31.989 32.283 33.836 34.350 34.550 34.756 34.779
1.4 3.739 7.366 10.784 13.924 16.745 19.236 21.406 23.278 24.884 26.255 27.424 28.420 29.271 29.998 30.621 31.157 31.618 32.018 32.365 32.667 34.374 34.813 35.035 35.247 35.271
1.5 3.763 7.414 10.856 14.018 16.861 19.373 21.563 23.454 25.077 26.465 27.649 28.660 29.523 30.262 30.897 31.443 31.914 32.322 32.677 32.986 34.641 35.202 35.436 35.663 35.689
1.6 3.783 7.453 10.914 14.095 16.956 19.485 21.692 23.599 25.236 26.638 27.835 28.857 29.732 30.482 31.226 31.680 32.160 32.575 32.937 33.253 34.950 35.532 35.776 36.017 36.046
1.7 3.799 7.485 10.962 14.158 17.034 19.578 21.798 23.718 25.368 26.781 27.989 29.022 29.906 30.665 31.317 31.879 32.366 32.888 33.156 33.477 35.211 35.812 36.067 36.321 36.352
1.8 3.812 7.512 11.002 14.211 17.099 19.655 21.886 23.817 25.478 26.900 28.118 29.160 30.052 30.818 31.477 32.046 32.539 32.967 33.340 33.666 35.435 36.052 36.316 36.584 36.617
1.9 3.824 7.534 11.035 14.254 17.153 19.719 21.960 23.900 25.570 27.001 28.226 26.276 30.175 30.948 31.613 32.188 32.686 33.119 33.497 33.828 35.626 35.259 36.532 36,812 36.847
2.0 3.833 7.553 11.062 14.291 17.199 19.773 22.022 23.970 25.647 27.086 28.318 29.374 31.279 31.058 31.728 32.308 32.811 33.249 33.631 33.965 35.791 36.438 36.719 37.011 37.048
3.0 3.876 7.639 11.192 14.463 17.412 20.027 22.316 24.302 26.016 27.491 28.757 29.846 30.783 31.592 32.291 32.898 33.427 33.889 34.294 34.551 36.640 37.380 37.715 38.107 38.157
4.0 3.888 7.663 11.228 14.511 17.471 20.098 22.398 24.398 26.121 27.606 28.884 29.983 30.930 31.748 32.457 33.074 33.611 34.082 34.496 34.860 36.915 37.699 38.063 38.510 38.579
5.0 3.893 7.672 11.241 14.529 17.494 20.125 22.430 24.432 26.161 27.650 28.932 30.035 30.986 31.808 32.521 33.142 33.683 34.157 34.574 34.943 37.028 37.834 38.214 38.696 38.781
10.0 3.897 7681 11.254 14.546 17.515 20.150 22.459 24.466 26.199 27.693 28.978 30.085 31.041 31.867 32.584 33.208 33.753 34.231 34.652 35.024 37.144 37,978, 38.382 38.927 39.057
INF 3.898 7.682 11.256 44.548 17.518 20.154 22.464 24.471 26.205 27.699 28.985 30.W3 31.049 310876 32.593 33.218 33.764 34.243 34.664 35.037 37.162 38.003 38.411 38.978 39.172
LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’ 7942:1976 Code of practice for daylighting
in the fulfillment of the requirements of the Code. The of educational buildings
latest version of a standard shall be adopted at the time (5) 1944 Code of practice for lighting of
of enforcement of the Code. The standards listed may (Parts 1 &2): public thoroughfares: Parts 1
be used by the Authority as a guide in conformance 1970 and 2 For main and secondary
with the requirements of the referred clauses in the roads (Group A and B) (first
Code. - revision)
IS No. Title 2672:1966 Code of practice for library
Recommendations for lighting
(1) 7662
(Part 1): 1974 orientation of buildings: Part 1 4347:1967 Code of practice for hospital
Non-industrial buildings lighting
(2) 3646 Code of practice for interior 6665:1972 Code of practice for industrial
(Part 1) :1992 illumination: Part 1 General lighting
requirements and 10894:1984 Code of practice for lighting of
recommendations for building educational institutions
interiors (jirst revision) Code of practice for lighting for
10947:1984
(3) 2440:1975 Guide for daylighting of ports and harbours
buildings (second revision) (6) 3362:1977 Code of practice for natural
(4) 6060:1971 Code of practice for daylighting ventilation of residential
of factory buildings buildings (jirst revision)

PART 8 BUILDING SERVICES — SECTION 1 LIGHTING AND VENTILATION 47


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES
Section 2 Electrical and Allied Installations

BUREAU OF INDIAN STANDARDS


p

CONTENTS

FOREWORD ... 3

1 SCOPE ... 5
2 TERMINOLOGY AND CONVENTIONAL SYMBOLS . .. 5
3 GENERAL REQUIREMENTS ... 9
4 PLANNING OF ELECTRICAL INSTALLATIONS ... 9
5 DISTRIBUTION OF SUPPLY AND CABLING ... 16
6 WIRING ... 28
7 FITTINGS AND ACCESSORIES ... 36
8 EARTHING .. 39
9 INSPECTION AND TESTING OF INSTALLATION ... 43
10 TELECOMMUNICATION AND OTHER MISCELLANEOUS SERVICES ... 48
11 LIGHTNING PROTECTION OF BUILDINGS ... 49

ANNEX A DRAWING SYMBOLS FOR ELECTRICAL INSTALLATION ... 56


IN BUILDING
ANNEX B EXTRACTS FROM INDIAN ELECTRICITY RULES, 1956 ... 58
ANNEX C AREA REQUIRED FOR TRANSFORMER ROOM AND ... 63
SUBSTATION FOR DIFFERENT CAPACITIES
ANNEX D ADDITIONAL AREA REQUIRED FOR GENERATOR IN ... 63
ELECTRIC SUBSTATION
ANNEX E FORM OF COMPLETION CERTIFICATE ... 64

LIST OF STANDARDS ... 65

NATIONAL BUILDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Section covers essential requirements for electrical and allied installations in buildlngs,

This Section was first published in 1970 and was subsequently revised in 1983. In the first revision, general
guidance for electrical wiring installation in industrial location where voltage supply normally exceeds 650 V
was included. This Section was also updated based on the existing version of the Indian Standards. The importance
of pre-planning and exchange of information among all concerned agencies from the earlier stages of building
work was emphasized.

As a result of experience gained in implementation of 1983 version of the Code and feedback received as well as
revision of some of the relevant standards based on which this Section was prepared, a need to revise this part
was felt. This revision been prepared to take care of these developments. The title of this Section
has, therefore,
has been modified from the erstwhile ‘electrical installations’ to ‘electrical and allied installations’ to reflect the
provisions now being included on certain allied installations. The significant changes incorporated in this revision
include:

a) The risk assessment procedure for lightening has been thoroughly changed apart from some other changes
in the provision of lightning protection of building.
b) Some of the provisions of wiring have now been aligned with the latest practices.
c) Many existing definitions have been modified in line with current terminologies used at national and
international level. Some new definitions have been added.
d) Provisions on installation of distribution transformer inside the multi-storeyed building have been
incorporated.
e) Concept of energy conservation in lighting has been introduced.
f) Concept of various types of earthing in building installation has been incorporated

This Section has to be read together with Part 8 ‘Building Services, Section 1 Lighting and Ventilation’ for
making provision for the desired levels of illumination as well as ventilation for different locations in different
occupancies. Utmost importance should be given in the installation of electrical wiring to prevent short circuiting
and the hazards associated therewith.

Notwithstanding the provisions given in this Section and the National Electrical Code, the provisions of the
Indian Electricity Act, 2003 and the Rules and Regulations framed thereunder have to be necessarily complied
with.

The information contained in this Section is largely based on the following Indian Standards/Special Publication:

IS 732:1989 Code of practice for electrical wiring installations (third revision)


1S 12032 Specification for graphical symbols for diagrams in the fi61d of electrotechnology:
(Part 11) :1987 Part 11 Architectural and topographical installation plan and diagrams
IS 4648:1968 Guide for electrical layout in residential buildings
IS 2309:1989 Protection of building and allied structures against lightning — Code of practice (second
revision)
SP 30:1984 National Electrical Code, 1985

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES
Section 2 Electrical and Allied Installations

1 SCOPE that when installed in uncovered locations, it will


withstand all kinds of weather variations (see 2.1.80,
This Section covers the essential requirements for
for definition of Weatherproofing).
electrical installations in buildings to ensure efficient
use of electricity including safety from fire and shock. 2.1.11 Cable, XLPE— A cable in which the insulation
This Section also includes general requirements of the conductor is cross-linked polythene and the
relating to lightning protection of buildings. mechanical protection is provided for the core or cores
by a sheath of a poly vinyl chloride compound.
2 TERMINOLOGY AND CONVENTIONAL
2.1.12 Ceiling Rose — A fitting (usually used to attach
SYMBOLS
to the ceiling) designed for the connection between
2.1 For the purpose of this Section, the following the electrical installation wiring and a flexible cord
definitions shall apply. (which is in turn connected to a lampholder).
2.1.1 Accessory — A device, other than current using 2.1.13 Circuit — An assembly of electrical equipment
equipment, associated with such equipment or with the supplied from the same origin and protected against
wiring on an installation. overcurrent by the same protective device(s). Certain
types of circuit are categorized as follows:
2.1.2 Apparatus — Electrical apparatus including all
machines, appliances and fittings in which conductors a) CategoW 1 Circuit — A circuit (other than a
are used or of which they form a part. fire alarm or emergency lighting circuit)
operating at low voltage and supplied directly
2.1.3 Appliance — An item of current using
from a mains supply system.
equipment other than a luminaire or an independent
b) Catego~ 2 Circuit — With the exception of
motor.
fire alarm and emergency lighting circuits,
2.1.4 Bunched — Cables are said to be ‘bunched’ any circuit for telecommunication (for
when two or more are contained within a single example, radio, telephone, sound distribution,
conduit, duct, ducting, or trunking or, if not enclosed, intruder alarm, bell and call and data
are not separated from each other. transmission circuits) which is supplied from
a safety source.
2.1.5 Cable — A length of single-insulated conductor
(solid or stranded), or two or more such conductors, c) Category 3 Circuit — A fire alarm circuit or
each provided with its own insulation, which are laid an emergency lighting circuit.
up together. The insulated conductor or conductors 2.1.14 Circuit Breaker — A mechanical switching
may or may not be provided with an overall mechanical device capable of making, carrying and breaking
protective covering. currents under normal circuit conditions and also of
2.1.6 Cable, Armoured — A cable provided with a making, carrying for a specified time, and breaking
wrapping of metal (usually in the form of tape or wire) currents under specified abnormal circuit conditions
serving as a mechanical protection. such as those of short circuit.
NOTE — A circuit breaker is, usually intended to operate in
2.L’7 Cable, Flexible — A cable containing one or frequently, although some types are suitable for frequent
more cores, each formed of a group of wires, the operation.
diameters of the cores and of the wires being sufficiently
2.1.15 Circuit, Final Sub — An outgoing circuit
small to afford flexibility.
connected to one-way distribution board and intended
2.1.8 Cable, Metal-Sheathed — An insulated cable to supply electrical energy at one or more points to
with a metal sheath. current, using appliances without the intervention of a
further distribution board other than a one-way board.
2.1.9 Cable, PVC Sheathed-Insulated — A cable
It includes all branches and extensions derived from
in which the insulation of the conductor is a
that particular way in the board.
polyvinylchloride (PVC) compound; with PVC sheath
also providing mechanical protection to the conductor 2.1.16 Cleat — An insulated incombustible support
core or cores in the cable. normally used for insulated cable.

2.1.10 Cable, Weatherproof— A cable so constructed 2.1.17 Conductor, Aerial — Any conductor which is

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 5

,,,,... --..
*
supported by insulators above the ground and is 2.1.30 Dead — A portion of the circuit (normally
directly exposed to the weather. expected to carry a voltage) at or near about earth
potential or apparently disconnected from any live
NOTE — Four classes of aerial conductors are recognized:
system.
a) Bare aerial conductors,
b) Covered aerial conductors, 2.1.31 Direct Earthing System — A system of earthing
c) Insulated aerial conductors, and in which the parts of an installation are so earthed as
d) Weatherproof neutral-screened cable. specified but are not connected within the installation
2.1.18 Conductor, Bare — A conductor not covered to the neutral conductor of the supply system or to earth
with insulating material. through the trip coil of an earth leakage circuit-breaker.

2.1.19 Conductor, Earthed — A conductor with no 2.1.32 Distance Area or Resistance Area {for Earth
provision for its insulation from earth. Electrode only) — The area of ground (around an earth
electrode) within which a voltage gradient measurable
2.1.20 Conductor, Insulated — A conductor with ordinary commercial instruments exists when the
adequately covered with insulating material of such electrode is being tested.
quality and thickness as to prevent danger.
2.1.33 Discrimination (Over-Current Discrimination)
2.1.21 Conductor of a Cable or Core — The — Co-ordination of the operating characteristics of two
conducting portion consisting of a single wire or group or more over-cument protective devices such that, on
of wires, assembled together and in contact with each the incidence of over-currents within stated limits, the
other or connected in parallel. device intended to operate within these limits does so,
—.
2.1.22 Connector — The part of a cable coupler or of while the others do not.
an appliance coupler which is provided with female NOTES
contact and is intended to be attached to the flexible 1 Protective devices should have discrimination so that only
cable connected to the supply. the affected part (minimum section) of the circuit is isolated,
even though a number of protective devices maybe in the path
2.1.23 Connector Box or Joint Box — A box forming of the over current.
apart of wiring installation, provided to contain joints 2 Distinction is made between series discrimination involving
different over-crment protective devices passing substantially
in the conductors of cables of the installations.
the same over-current and network discrimination involving
2.1.24 Connector for Portable Appliances — A identical protective devices passing different proportions of
the over-cument.
combination of a plug and socket arranged for
attachment to a portable electrical appliance or to a 2.1.34 Earth — The conductive mass of the earth,
flexible cord. whose electric potential at any point is conventionally
taken as zero.
2.1.25 Consumer’s Terminals — The ends of the
electrical conductors situated upon any consumer’s 2.1.35 Earth Continuity Conductor — The conductor,
premises and belonging to him at which the supply of including any clamp, connecting to the earthing lead
energy is delivered from the service line. or to each other those parts of an installation which
are required to be earthed. It may be in whole or in
2.1.26 Cord, Flexible — A flexible cable having
part the metal conduit or the metal sheath or armour of
conductor of small cross-sectional area. Two flexible
the cables, or the special continuity conductor of a cable
cords twisted together are known as twin ‘flexible
or flexible cord incorporating such a conductor.
cord’.
2.1.36 Earth Electrode — A conductor or group of
2.1.27 Core of a Cable — A single conductor of a
conductors in intimate c?ntact with and providing an
cable with its insulation but not including any
electrical connection to earth.
mechanical protective covering.
2.1.37 Earth Fault — Accidental connections of a
2.1.28 Cut-out — Any appliance for automatically
conductor to earth when the impedance is negligible,
interrupting the transmission of energy through any
the connection is called a dead earth.
conductor when the current rises above a pre-
determined amount. 2.1.38 Earthing Lead— The final conductor by which
the connection to the earth electrode is made.
2.1.29 Damp Situation — A situation in which
moisture is either permanently present or intermittently 2.1.39 Earth Leakage Circuit Breaker System — A
present to such an extent as to be likely to impair the system of earthing in which the parts of an installation,
effectiveness of an installation conforming to the specified, to be earthed are so earthed through one or
requirements for ordinary situations. more earth leakage circuit-breakers or relays.

6 NATIONAL BUILDING CODE OF INDIA


2.1.40 Enclosed Distribution Board — An enclosure 2.1.47 Fuse-Element — A part of the fuse-link
containing bus bars with one or more control and designed to melt under the action of current
protected devices for the purpose of protecting, exceeding some definite value for a definite period of
controlling or connecting more than one outgoing time.
circuits fed from one or more incoming circuits.
2.1.48 Harmonics (Current and Voltage) — All
2.1.41 Exposed Metal — All metal parts of an alternating current which is not absolutely sinusoidal
installation which areeasily accessible other than: is made up of a fundamental and a certain number
of current harmonics which are the cause of its
a) parts separated from live parts by double
deformation (distortion) when compared to the
insulation;
theoretical sine-wave.
b) metal name-plates, screw heads, covers, or
plates, which are supported on or attached or 2.1.49 In.arnmable — A material capable of being
connected to substantial non-conducting easily ignited.
material only in such a manner that they do 2.1.50 Installation (Electrical), of Buildings — An
not become alive in the event of failure of assembly of associated electrical equipment to fulfil a
insulation of live parts and whose means of specific purpose or purposes and having coordinated
fixing do not come in contact with any internal characteristics.
metal; and
2.1.51 Insulated — Insulated shall mean separated
c) parts which are separated from live parts by
from adjacent conducting material or protected from
other metal parts which are themselves
personal contact by a non-conducting substance or an
earthed or have double insulation.
air space, in either case offering permanently sufficient
2.1.42 Fire Survival Cable — A cable which continues resistance to the passage of current or to dkwuptive
in service after exposure to a temperature of 900”C discharges through or over the surface of the substance
for 20 min or 700”C for 90 min. or space, to obviate danger or shock or injurious
leakage of current.
2.1.43 Fitting, Lighting — A device for supporting or
containing a lamp or lamps (for example, fluorescent 2.1.52 Insulation, Basic — Insulation applied to live
or incandescent) together with any holder, shade, or parts to provide basic protection against electric shock.
reflector, for exmple, a bracket, a pendant with ceiling NOTE — Basic insulation does not necessarily include
rose, an electrolier, or a portable unit. insulation used exclusively for functional purposes.
2.1.44 Flameproof Enclosure — An enclosure which 2.1.53 Insulation, Double — Insulation comprising
will withstand without injury any explosion of both basic and supplementary insulation.
inflammable gas that may occur within it under
2.1.54 Insulation (Electrical) — Suitable non-
practical conditions of operation within the rating of
conducting material, enclosing, surrounding or
the apparatus (and recognized overloads, if any,
supporting a conductor.
associated therewith) and will prevent the transmission
of flame which may ignite any inflammable gas that 2.1.55 Insulation, Reinforced — Single insulation
may be present in the surrounding atmosphere. applied to live parts, which provides a degree of
NOTES
protection against electric shock equivalent to double
1 Hazardous areas are classified into different zones, depending insulation under the conditions specified in the relevant
upon the extent to which an explosive atmosphere could exist standard.
at that place. In such areas ffame proof switchgear, fittings,
NOTE — The term ‘single insulation’ does not imply that the
accessories, have to be used/installed in flameproof enclosure.
insulation must be one homogeneous piece. It may comprise
2 An electrical apparatus is not considered as flameproof severaf layers which catmot & tested singly as supplementary
unless it complies with the appropriate statutory regulations. or basic insulation.
3 Other types of fittings are also in vogue in wiring
installations, for example, ‘increased safety’. 2.1.56 Insulation, Supplementary — Independent
insulation applied in addition to basic insulation in
2.1.45 Flame Retardant Cable — Flame retardant
order to provide protection against electric shock in
cable with reduced halogen evaluation and smoke.
the event of a failure of basic insulation.
2.1.46 Fuse — A device that, by the fusion of one or
2.1.57 Linked Switch — Switches linked together
more of its specially designed and proportioned
mechanically so as to operate simultaneously or in
components, opens the circuit in which it is inserted
definite sequence.
when the current through it exceeds a given value for
a sufficient time. The fuse comprises all the parts that 2.1.58 Live or Alive — Electrically charged so as to
form the complete device. have a potential different from that of earth.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 7


2.1.59 Locations, Industrial — Locations where tools normal circuit conditions, which may include specified
and machinery requiring electrical wiring are installed operating overload conditions, and also of carrying for
for manufacture or repair. a specified time currents under specified abnormal
circuit conditions such as those of short circuit.
2.1.60 Locations, Non-Industrial — Locations other
than industrial locations, and shall include residences, NOTE — A switch may also be capable of making, but not
breaking, short-circuit currents.
offices, shops, showrooms, stores and similar premises
requiring electrical wiring for lighting, or similar 2.1.70 Switchboard — An assembly of switchgear
purposes. with or without instruments, but the term does not apply
to a group of local switches in a final circuit.
2.1.61 Miniature Circuit Breaker — Mechanical
switching device capable of making, carrying and NOTE — The term ‘switchboard’ includes a distribution board.
breaking currents under normal circuit conditions and
2.1.71 Switch Disconnectors — A device used to open
also making carrying currents for specified times and
(or close) a circuit when either negligible current is
automatically breaking currents under specified
interrupted (or established) or when the significant
abnormal circuit conditions such as those of overload
change in the voltage across the terminals of each of
and short circuits.
the pole of the disconnectors occurs; in the open
2.1.62 Multiple Earthed Neutral System — A system position it provides an isolating distance between the
of earthing in which the parts of an installation terminals of each pole.
specified to be earthed are connected to the general
2.1.72 Switch Disconnector Fuse — A composite unit,
mass of earth and, in addition, are connected within
comprising a switch with the fuse contained in or
the installation to the neutral conductor of the supply
mounted on the moving member of the switch. ..-
system.
2.1.73 Switchgear — A general term covering
2.1.63 Neutral Conductor — Includes the neutral
switching devices and their combination with
conductor of a three-phase four-wire system, the
associated control, measuring, protective and
conductor of a single-phase or dc installation which is
regulating equipment, also assemblies of such devices
earthed by the supply undertaking (or otherwise at the
and equipment with associated interconnections,
source of the supply), and the middle wire or common
accessories, enclosures and supporting structures,
return conductor of a three-wire dc or single-phase ac
intended in principle for use in connection with
system.
generation, transmission, distribution and conversion
2.1.64 Plug — A device, provided with contact pins, of electric energy.
which is intended to be attached to a flexible cable,
2.L74 Usable Wall Space — All portions of a wall,
and which can be engaged with a socket outlet or with
except that occupied by a door in its normal open
a connector.
position, or occupied by a fire place opening, but
2.1.65 Point (in Wiring) — A termination of the fixed excluding wall spaces which are less than 1 m in extent
wiring intended for the connection of current using measured along the wall at the floor line.
equipment.
2.1.75 Voltage, Extra Low (ELV) — The voltage
2.1.66 Residual Current Circuit Breaker — A which does not normally exceed 50 V.
mechanical switching device design to make, carry and
2.1.76 Voltage, Low (LV) — The voltage which
break currents under normal service conditions and to
normally exceed 50 V but does not normally exceed
cause the opening of the contacts when the residual
250 V.
currents attains a giving value under specified
conditions. 2.1.77 Voltage, Medium (MV) — The voltage which
normally exceeds 250 V hut does not exceed 650 V.
2.1.67 Service — The conductors and equipment
required for delivering energy from the electric supply 2.1.78 Voltage, High (HT, HV) — The voltage which
system to the wiring system of the premises served. normally exceeds 650 V but less than or equal to 33 kV.
2.1.68 Socket-Outlet — Accessory having socket 2.1.79 Voltage, Extra High (EHT) — The voltage,
contacts designed to engage with the pins of a plug which normally exceeds 33 kV.
and having terminals for the connection of cable(s).
2.1.80 Weatherproof — Accessories, lighting fittings,
NOTE — A Iuminaire track system is not regarded as a socket- current-using appliances and cables are said to be of the
outlet system.
weatherproof type, if they are so constructed that when
2.1.69 Switch — A mechanical switching device installed in open situation they will withstand the effects
capable of making, carrying and breaking current under of rain, snow, dust and temperature variations.

8 NATIONAL BUILDING CODE OF INDIA


P’-

For definition of other terms reference may be made submain and feeder. Power factor and efficiency of
to accepted standards [8-2(1)]. loads shall also be considered. Diversity factor assumed
shall be based on one’s own experience. Allowance
2.2 Conventional Symbols should be made for about 15 percent to 20 percent for
The architectural symbols that are to be used in all extension in near future and the design circuit is
drawings, wiring plans, etc, for electrical installations calculated for each circuit and submain. The wiring
in buildings shall be as given in Annex A. system to be adopted should also be decided in
accordance with the environmental requirements. The
For other graphical symbols used in electrotechnology, sizes of wiring cables are decided not merely to carry
reference may be made to good practice [8-2(1)]. the load currents, but also to withstand thermal effects
of likely over currents and also ensure acceptance level
3 GENERAL REQUIREMENTS
of voltage drop.
3.1 Conformity with Electricity Act 2003 and Rules
3.4 Power Factor Improvement in Consumers’
Amended Up-to-date
Installation
The installation shall generally be carried out in
3.4.1 Conditions of supply of electricity boards or
conformity with the requirements of The Electrici~
licensees stipulate the lower-limit of power factor
Act, 2003 as amended up-to-date and the Indian
which is generally 0.85.
Electrici~ Rules, 1956 framed thereunder and also the
relevant regulations of the Electric Supply Authority 3.4.2 Principal causes of low power factor are many.
concerned as amended from time to time. Extracts from For guidance to the consumers of electric energy who
the Indian Electricity Rules, 1956, referred to in this take supply at low and medium voltages for --
section, are given in Annex B. improvement of power factor, ‘reference shall be made
NOTE — Indian Electricity Rules which are being revised
in accordance with good practice [8-2(2)].
would become applicable on their notification.
3.5 Execution of Work
3.2 Materials
Unless otherwise exempted under the appropriate rule
All materials, fittings, appliances, etc, used in electrical of the Indian Electrici~ Rules, the work of electrical
and allied installations, shall conform to Part 5 ‘Building installations shall be carried out by a licensed electrical
Materials’ and other related Indian Standards. contractor and under the direct supervision of a person
holding a certificate of competency and by persons
3.3 Coordination with Local Supply Authority holding a valid permit issued and recognized by any
a) In all cases, that is, whether the proposed State government.
electrical work is a new installation or 3.6 Safety procedures and practices shall be kept in
extension of an existing one, or a modification view during execution of the work in accordance with
involving major changes, the electricity good practice [8-2(4)].
supply undertaking shall be consulted about
the feasibility, etc, at an early date. 3.7 Safety provisions given in Part 4 ‘Fire and Life
Safety’ shall be followed.
b) Addition to an Installation — An addition,
temporary or permanent, shall not be made 4 PLANNING OF ELECTRICAL
to the authorized load of an existing INSTALLATIONS
installation, until it has been definitely
4.1 General
ascertained that the current carrying capacity
and the condition of existing accessories, The design and planning of an electrical wiring
conductors, switches, etc, affected, including installation involve consideration of all prevailing
those of the supply authority are adequate for conditions, and is usually influenced by the type and
the increased load. The size of the cable/ requirement of the consumer. A competent electrical
conductor shall be suitably selected on the design engineer should be involved at the planning
basis of the ratings of the protective devices. stage with a view to providing for an installation that
Ratings of protective devices and their types will prove adequate for its intended purpose, and safe
shall be based on the installed load, switching and efficient in its use. The information given in 3 shall
characteristics and power factor. also be kept in view.

Load assessment and application of suitable diversity 4.1.1 The design and planning of an electrical wiring
factor to estimate the full load current shall be made installation shall take into consideration, some or all
as a first step. This should be done for every circuit, of the following:

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 9


a) the type of supply, occupancy, envisaged load of electricity for lighting, general purpose socket-
and the earthing arrangement available; outlet, kitchen heating, etc.
b) the atmospheric condition, such as cooling It is essential that adequate provision should be made
air temperature, moisture or such other for all the services which may be.required immediately
conditions which are likely to affect the and during the intended useful life of the building, for
installation adversely; the householder may otherwise be tempted to carry
c) the possible presence of inflammable or out extension of the installation himself or to rely upon
explosive dust, vapour or gas; use of multiplug adopters and long flexible cords, both
d) the degree of electrical and mechanical of which are not recommended.
protection necessary;
4.2 Location and Requirement of Substation
e) the importance of continuity of service
including the possible need for standby Information on location and requirements of a
supply; substation should cover the following:
9 the probability of need for modification or
4.2.1 Location
future extension;
the probable operation and maintenance cost a) The substation should preferably be located
g)
taking into account the electricity supply in separate building and could be adjacent to
tariffs available; the generator room, if any. Location of
substation in the basement floors should be
h) the relative cost of various alternative
avoided, as far as possible.
methods;
b) The ideal location for an electrical substation
j) the need for radio and telecommunication
for a group of buildings would be at the
interference suppression;
electrical load centre on the ground floor.
k) case of maintenance;
c) The floor level of the substation or switch
m) safety aspects;
room shall be above the highest flood level
n) energy conservation; and of the locality.
P) the importance of proper discrimination d) Generally the load centre would be
between protective devices for continuity of somewhere between the geometrical centre
supply and limited isolation of only the and the air conditioning plant room, as air
affected portion. conditioning plant room would normally be
4.1.2 All electrical apparatus shall be suitable for the the largest chunk of load, if the building is air
services these are intended for, conditioned,
e) Substations with oil filled equipment will
4.1.3 Co-ordination
require great consideration for the fire
Proper co-ordination and collaboration between the detection, protection and suppression. Oil
architect, civil engineer and the electrical and mechanical cooled transformers require a suitable soak
engineer shall be effected from the planning stage of pit with gravity flow to contain the oil in the
the installation. The provisions that will be needed for event of the possibility of oil spillage from
the accommodation of substation, transformer, the transformer on its failure. Substations with
switchrooms, service cable ducts, rising mains and oil filled equipment shall not be located in
distribution cables, sub-distribution boards, openings any floor other than the ground floor or a
and chases in floors and walls for all required electrical semi-basement. Such substations with high oil
installations, etc, shall be specified in advance. content may be housed in a separate service
building or a substation building, which is not
4.1.4 Before starting wiring and installation of fittings
the part of a multi-storeyed building.
and accessories, information should be exchanged
f) In case electric substation has to be located
between the owner of the building/architect/electrical
within the main multi-storeyed building itself
contractor and the local supply authority in respect of
for unavoidable reasons, then it should be
tariffs applicable, types of apparatus that may be
located on the floor close to ground level, but
connected under each tariff, requirement of space for
shall have direct access from the street for
installing meters, switches, etc, and for total load
operation of the equipments. The provision
requirements of lights, fans and power.
for installation and removal of substation
4.1.5 While planning an installation, consideration equipments may be provided from inside the
should be taken of the anticipated increase in the use building.

10 NATIONAL BUILDING CODE OF INDIA


Substations located within a multi-storeyed (more than 2000 litres), Rule 64 of Indian
building shall not have oil filled transformers, Electricity Rules, 1956 as amended time to
even if it is at the ground level (see Part 4 time shall apply.
‘Fire and Life Safety’). Substations with very P) Facility for connection from substation
little combustible material, such as a Dry type to adjoining building to feed essential
transformer, with Vaccum (or SFJ HT emergency load in that building, such as
switchgear and ACB or MCCB for MV can escape route lighting, fue or sprinkler pumps,
be located in the basement as well as upper emergency communication systems shall be
floors in a building with high load density in provided. Similarly, the essential emergency
the upper floors. (Some functional buildings load switchboard of this building or building
such as hospitals, air traffic control towers, complex should be so as to be capable of
computer centres are likely to have high receiving power for such loads from the
loading in a few upper floors and in such adjoining building or building complex, with
cases, it maybe preferable to provide oil-free its own substation/DG sets shut off due to
substations at upper levels. This measure will crisis conditions such as fire.
decrease the current flow at various points, @ The availability of power lines nearby may
thereby contributing to reduction of also be kept in view while deciding the
vulnerability to fire). location of the substation.
h) The power supply control to any such r) For detailed information regarding location
substation or transformer (located at basement of transformers reference may be made to
levels or upper floors) shall be from a location good practice [8-2(3)].
on ground floor/first basement level having s) All door openings from substation, electrical
direct access from outside so that in case of rooms, etc should open towards outside.
fire, the electrical supply can be easily
t) For acoustical enclosures/treatment reference
disconnected. .
may be made to Part 8 ‘Building Services,
j) Oil filled transformers may be used only in Section 4 Acoustics, Sound Insulation and
substations located in separate single or two Noise Control’.
storeyed service buildings outside the main
building structure and there shall atleast 4.2.2 Type of Building for Substations
6 meter clear distance between the adjoining The substations enclosure, that is, walls, floor, ceiling,
buildings and substation such that fire tender openings, doors, etc shall have 2 hour fire rating (see
is able to pass between the two structures. Part 4 ‘Fire and Life Safety’).
k) If dry type transformer is used, it may
4.2.3 Luyout of Substation
be located adjacent to medium voltage
switchgear in the form of unit type substation. In allocating the area of substation, it is to be noted
No separate room or fire barrier for the that the flow of electric power is from supply
transformer is required, in a substation with company’s room to HV room, then to transformer and
oil free equipment. In such a case the room finally to the medium voltage switchgear room. The
size will decrease. Layout of equipment has layout of the room shall be in accordance with this
to keep the requirement that any one piece of flow, so as to optimise the cables, bus-trnnking etc,
equipment or sub-assembly can be taken out Visibility of equipment c@rolled from the operating
of service and out of the installed location, point of the controlling switchgear is also a desirable
while keeping the remaining system in feature, though it may not be achievable in case of
service. large substations. ,
m) The emergency power supply (such as 4.2.4 Room/Spaces Required
Generating Sets) should not be allowed to be
Generally the following roomslspaces are required in
installed above ground floor or below first
a substation:
basement level of building. There shall be
provision of separate direct escape and entry a) Supply company’s switchgear room andlor
into these areas from outside so that in case space for meters.
of fire, electrical supplies can be disconnected b) Capacity and Size — The capacity of a
to avoid additional losses which may be substation depends upon the area of the
caused due to electrical supply, present at the building and its type. The capacity of
time of fire. substation may be determined based on the
n) For transformers having large oil content following load requirements:

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 11


T

Table of Typical Allowances for Diversity

Purpose of Final Circuit Individual Household Type of Premises Type of Premises Small
Fed from Conductors or Installations, including Small, Shops, Stores Hotels, Boarding
Switchgear to which Individual Dwelling Offices and Business Houses etc.
Diversity Applies of a Block Premises
(1] (2] (3) (4)

Lighting 66% of total demand 90% of total current 75% of total current
demand demand
Heating and power 80% of total current 809. full load of largest 80~o full load of largest
demand upto 10A appliance appliance
+4070 of any current +6070 of remaining +607. of second largest
demand in excess of appliances appliances
10A +4090 of remaining
appliances
Cooking appliances 10A 80% full load of largest 80% of largest appliance
+30% full load of appliance
connected cooking +607. full load of +60% of full load of
appliances in excess of second largest appliance second largest appliance
10A + 5 A if socket- +5070 full load of +5070 full load of
outlet incorporated in remaining appliances remaining appliances
Unit.
Motors (other than lift 80% full load of largest 80% full load of largest
motors which are subject motor motor
to special consideration) +60Y0 full load of +5090 full load of
second largest motor remaining motors
+509. full load of
remaining motors
Water heater 8070 full load of largest 80% full load of largest 80~0 full load of largest
appliance appliance appliance
+50% of second largest +609. of second largest +60Y0 of second largest
appliance appliance appliance
+25% full load of +259. full load of +25 ~0 full load of
remaining appliances remaining appliances remaining appliances
Floor warming 50’%0
installations

Water heaters thermal 50%


storage space heating
installations
Standard arrangements of 80% of current demand 80% of current demand
final circuits in of largest circuit of largest circuit
accordance with IS 732 +4O’%O of current demand +507. of current demand
of every other circuit of every other circuit
Socket outlets other than 80% of current demand 80% of current demand 80% of current demand of
those included above and of largest point of +4070 of largest point of largest point of +60% of
stationary equipment of current demand of +6070 of current current demand of every
other than those listed every other point of. demand of every other point in main rooms
above point of (dinning rooms, etc) +40%
of current demand of every
other point of.
NOTES
1 For the purpose of the table an instantaneous water heater is deemed to be a water heater of anY loading which heats water only
while the tap is turned on and therefore uses electricity intermittently.
2 It is important to ensure that the distribution boards are of sufficient rating to take the totat load comected to them without the
application of any diversity.

12 NATIONAL BUILDING CODE OF INDIA


After calculating the electrical load on the 9 Facilities including space at appropriate
above basis, a load factor of 70-90 percent is positions, relative to the location of the
to be applied to arrive at the minimum installed equipment has to be kept in the
capacity of substation. The area required for layout design for removal of equipment or
substation and transformer room for different sub-assemblies for repair or maintenance.
capacities is given in Annex C for general When it is located, other than the ground level
guidance. For reliability, it would be with direct equipment access, a hatch or ramp
necessary to split the load into more than one shall be required.
transformer and also provide for standby h) Other environmental requirements under the
transformer as well as multiple sources, bus- provisions of Environment Protection Rules,
section, etc. 1986 as amended time-to-time shall be taken
c) High Voltage Switch Room — In case of into” account from the aspect of engine
substation having one transformer and one emissions including regarding the height of
source of supply, the owner is required to exhaust pipe and permitted noise levels/noise
provide one high voltage switch. In case control.
of single point supply with two or more j) The capacity of standby generating set shall
transformers the number of switch required be chosen on the basis of essential light load,
will be one for incoming supply and one for essential air conditioning load, essential
each transformer. In case of duplicate supply equipment load and essential services load,
two switches shall be provided with such as one lift out of the bank of lifts, one or
mechanical/electrical in locking arrangement all water pumps, etc. Having chosen the
where necessary in cables with switches. In capacity and number of generating sets,
case the number of incoming and outgoing required space may be provided for their
switches exceed five, bus coupler of suitable installation (see Annex D for general
capacity should invariably be provided. guidance).
The floor area required in case of a single k) The generating set should preferably be
switch is roughly 4 m x 4 m and for every housed adjacent to MV switchgear in the
additional switch the length would be substation building to enable transfer of
increased by 1 m. electrical load quickly as well as to avoid
d) Facility for connection from substation of transfer of vibration and noise to the main
adjoining building to feed emergency loads building. Acoustics lining of the room shall
shall be permitted for feeding escape route be in line with the requirements of Central
and signage lighting as well as selected Pollution Control Board (CPCB). If DG Set
section of the fire protection system. Similarly is located outdoor, it shall be housed in
on a reciprocal basis facility to feed the acoustics enclosure. The generator house
adjoining building for such emergency loads should have proper ventilation, fire fighting
may be provided by necessary switchgear, equipment, etc (see also 4.2.2).
e) Medium Voltage Switch Room — The floor m) Requirements of Room
area required in respect of medium voltage 1) The areas given above in respect of the
switchgear room maybe determined keeping different categories of rooms holds good
in view the number and type of incomingl if they are provided with windows and
outgoing bus coupler switches including independent access doors in accordance
likely expansion in future. with local regulations.
f) Room for Standby Generator — It is preferable 2) All the rooms shall be provided with
to install the standby generator in service partitions up to the ceiling and shall have
building. If installed in main building it shall proper ventilation. Special care should
beat the ground floor or at the semi basement, be taken to ventilate the transformer
alternatively, in the first basement with rooms and where necessary louvers at
facilities for forced ventilation. Adequate lower level and exhaust fans at higher
space shall be provided for storing of fuel. level shall be provided at suitable
Compartmentation for fire protection with locations.
detection and first-aid protection measures is 3) In order to prevent storm water entering
essential. Different type of requirements exist the transformer and switch rooms
for the diesel engine and generator for the oil through the soak-pits, the floor level, the
storage area and for the switchgear. substation shall be at least 15 cm above

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 13


the highest flood water level that may be avoidable abnormality and shall take care of the safety
anticipated in the locality. Also, facility requirements as follows:
shall be provided for automatic removal
a) enclose the substation where necessary to
of water.
prevent, so far as is reasonably practicable,
4) The minimum height of high voltage danger or unauthorised access;
switchgear room shall be 3.6 m below the
b) enclose any part of the substation, which is
soffit of the beam.
open to the air and contains live equipment
n) Fire Compartmentation — It is advisable to which is not encased, with a fence or wall not
provide fire compartmentation of buildings less than 2.4 m in height to prevent, so far
and segregation of associated wiring. Busbar as is reasonably practicable, danger or
tmnking of horizontal and vertical distribution unauthorised access;
type in place of cable based distribution c) ensure that, so far as is reasonably practicable,
system shall be used. there are at all times displayed:
4.3 Location of Switch Room 1) sufficient safety signs of such size and
placed in such positions as are necessary
In large installations other than where a substation is
to give due warning of such danger as
provided, a separate switch room shall be provided;
is reasonably foreseeable in the
this shall be located as closely as possible to the
circumstances;
electrical load centre preferably near the entrance of
the building on the ground floor or on the first 2) a notice which is placed in a conspicuous
basement level, and suitable ducts shall be laid with position and which gives the location or
. ---
identification of the substation, the name
minimum number of bends from the points of entry
of the main supply cable to the position of the main of each generator or distributor who owns
switchgear. The switch room shall also be placed in or operates the substation equipment
making up the substation and the
such a position that rising ducts may readily be
provided therefrom to the upper floors of the building telephone number where a suitably
in one straight vertical run. In larger buildings, more qualified person appointed for this
purpose by the generator or distributor
than one rising duct may be required and then
horizontal ducts may also be required for running will be in constant attendance; and
cables from the switch room to the foot of each rising 3) such other signs, which are of such size
main. Such cable ducts shall be either be reserved for and placed in such positions, as are
the electrical services only or provided with a means necessary to give due warning of danger
of segregation for medium and low voltage having regard to the siting of, the nature
installations, such as call-bell systems; telephone of, and the measures taken to ensure the
installations, fire detection and alarm system, physical security of, the substation
announcement or public address system. Cables for equipmenq and
essential emergency services such as those related to d) take all reasonable precautions to minimize
fire detection, alarm, announcement should use either the risk of fire associated with the equipment.
metal conduit in addition to physical segregation from
power cables or use fire survival cables, so that the 4.6 Overhead Lines, Wires and Cables
service is maintained even in the event of a fire at 4.6.1 Height Requirement
least for a period of about 20 min.
While overhead lines may not be relevant within
4.4 Location and Requirements of Distribution buildings, regulations related to overhead lines are of
Panels concern from two differerft angles.
The electrical control gear distribution panels and other a) Overhead lines may be required in building
apparatus, which are required on each floor may complexes, though use of underground cables
conveniently be mounted adjacent to the rising mains, is the preferred alternative.
and adequate space should be provided at each floor b) Overhead lines may be passing through the
for this purpose. site of a building. In such a case the safety
aspects are important for the construction
4.5 Substation Safety
activity in the vicinity of the overhead line as
The owner or the operator of any substation shall be well as portions of low height buildings that
collectively and severally be responsible for any lapse may have to be constructed below the
or neglect leading to an accident or an incidence of an overhead lines.

14 NATIONAL BUILDING CODE OF INDIA


For minimum distance (vertical and practicable, any unauthorised person from reaching a
horizontal) of electric lines/wires/cables from position at which any such line would be a source of
buildings, reference may be made to Part 3 danger.
‘Development Control Rules and General
Every support carrying a high voltage overhead line,
Building Requirements’.
and every support carrying a low voltage overhead line
c) Any person responsible for erecting incorporating bare phase conductors, shall have
an overhead line will keep informed the attached to it sufficient safety signs and placed in such
authority(s) responsible for services in that positions as are necessary to give due warning of
area for telecommunication, gas distribution, such danger as is reasonably foreseeable in the
water and sewage network, roads so as to have circumstances.
proper co-ordination to ensure safety. He
shall also publish the testing, energizing Poles supporting overhead lines near the road junctions
programme for the line in the interests of and turnings shall be protected by a masonry or earth
safety. fill structure or metal barricade, to prevent a vehicle
from directly hitting the pole, so that the vehicle, if out
4.6.2 Position, Insulation and Protection of Overhead of control, is restrained from causing total damage to
Lines the live conductor system, likely to lead to a hazardous
Any part of an overhead line which is not connected condition on the road or foot path or building.
with earth and which is not ordinarily accessible shall 4.6.4 Fitting of Insulators to Stay Wires
be supported on insulators or surrounded by
insulation. Every stay wire which forms part of, or is attached to,
any support carrying an overhead line incorporating
Any part of an overhead line which is not connected bare phase conductors (except where the support is a
with earth and which is ordinarily accessible shall lattice steel structure or other structure entirely of metal
be: and connected to earth) shall be fitted with an insulator “
a) made dead; or no part of which shall be less than 3 m above ground
b) so insulated that it is protected, so far it is or above the normal height of any such line attached
to that support.
reasonably practicable, against mechanical
damage or interference; or
4.7 Maps of Underground Networks
c) adequately protected to prevent danger.
4.7.1 Any person or organization or authority laying
Any person responsible for erecting a building or cables shall contact the local authority in charge of that
structure which will cause any part of an overhead line area and find out the layout of
which is not connected with earth to become ordinarily
accessible shall give reasonable notice to the generator a) water distribution pipe lines in the area;
or distributor who owns or operates the overhead line b) sewage distribution network,
of his intention to erect that building or structure. c) telecommunication network; and
Any bare conductor not connected with earth, which d) gas pipeline network and plan the cable
is part of a low voltage overhead line, shall be situated network in such a manner that the system is
throughout its length directly above a bare conductor compatible, safe and non interfering either
which is connected with earth. during its installation or during its operation
and maintenance. Plan of the proposed cable
No overhead line shall, so far as is reasonably
installation shall be brought to the notice of
practicable, come so close to any building, tree or
the other authorities referred above.
structure as to cause danger.
4.7.2 Suitable cable markers and danger sign as would
In this regulation the expression “ordinarily accessible”
be appropriate for the safety of the workmen of any of
means the overhead line could be reached by hand if
the systems shall be installed along with the cable
any scaffolding, ladder or other construction was
installation. Notification of testing and energisation of
erected or placed on/in, against or near to a building
the system shall also be suitably published for ensuring
or structure.
safety.
4.6.3 Precautions Against Access and Warnings of
4.7.3 Any person or organization or authority laying
Dangers
cables shall have and, so far it is reasonably practicable,
Every support carrying a high voltage overhead line keep up to date, a map or series of maps indicating the
shall, if the circumstances reasonably require, be fitted position and depth below surface level of all networks
with devices to prevent, so far it is reasonably or parts thereof which he owns or operates.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 15


Any map prepared or kept shall be available for 5.1.3 In very large industrial buildings where heavy
inspection by any of the municipal authority, other electric demands occur at scattered locations, the
service providers, general public provided they have a economics of electrical distribution at high voltage
reasonable cause for requiring to inspect any part of from the main substation to other subsidiary
the map. transformer substations or to certain items of plant,
such as large motors and furnaces, should be
5 DISTRIBUTION OF SUPPLY AND CABLING considered. The relative economy attainable by use of
5.0 General medium or high voltage distribution and high voltage
plant is a matter for expert judgement and individual
In the planning and design of an electrical wiring assessment in the light of experience by a professionally
installation, due consideration shall be made of all the qualified electrical engineer.
prevailing conditions. It is recommended that advice
of a competent electrical engineer be sought at the 5.2 Substation Equipment and Accessories
initial stage itself with a view to providing an Substations require an approval by the Electrical
installation, that will prove adequate for its intended Inspectorate. Such approval is mandatory before
purpose be reliable and safe and efficient. energizing the substation. It is desirable to get the
A certain redundancy in the electrical system is approval for the general layout, schematic layout,
necessary and has to be built in from the initial protection plan etc, before the start of the work from
design stage itself. The extent of redundancy will the Inspectorate. All substation equipment and
depend on the type of load, its criticality, normal hours accessories and materials, etc, shall conform to relevant
Indian Standards wherever they exist, otherwise the
of use, quality of power supply in that area,
consumer (or his consultant) has to specify the
coordination with the standby power supply, capacity
standards to which ‘the equipment to be supplied
to meet the starting current requirements of large
confirms and that shall be approved by the authority.
motors etc.
Manufacturers of equipment have to furnish certificate
5.1 System of Supply of conformity as well as type test certificates for record,
in addition to specified test certificates for acceptance
5.1.1 All electrical apparatus shall be suitable for the tests and installation related tests for earthing, earth
voltage and frequency of supply. continuity, load tests and tests for performance of
5.1.2 In case of connected load of 100 kVA and above, protective gear.
the relative advantage of high voltage three-phase 5.2.1 High Voltage Switchgear
supply should be considered. Though the use of high
voltage supply entails the provisions of space for the 5.2.1.1 The selection of the type of high voltage
capital cost of providing suitable transformer substation switchgear for any installation inter alia depends upon
the following:
at the consumer’s premises, the following advantages
are gained: a) voltage of the supply system;

a) advantage in tariffi b) the prospective short-circuit current at the


point of supply;
b) more effective earth fault protection for heavy
current circuits; c) the size and layout of electrical installation;

c) elimination of interference with supplies to d) the accommodation available; and


other consumers permitting the use of large e) the nature of industry.
size motors, welding plant, etc; and Making and breaking cap~ity of switchgear shall be
d) better control of voltage regulation and more commensurate with short-circuit potentialities of the
constant supply voltage. supply system and the supply authority shall be
NOTE — Additional safety precautions required to consulted on thk subject.
be observed in HV installations shall also be kept in
view. 5.2.1.2 Guidelines on various types of switchgear
equipment and their choice for a particular application
In many cases there maybe no choice available to the
shall be in accordance with good practice [8-2(4)].
consumer, as most of the licensees have formulated
their policy of correlating the supply voltage with the 5.2.1.3 In extensive installations of switchgear (having
connected load or the contract demand, Generally the more than four incoming supply cables or having more
supply is at 400/230 volts, 11 kV (or 22 kV) for loads than 12 circuit breakers), banks of switchgears shall
up to 5 MVA and 33 kV or 66 kV for consumers of be segregated from each other by means of fire-
more than 5 MVA. resisting barriers having 2 h fire resistance rating in

16 NATIONAL BUILDING CODE OF INDIA


order to prevent spreading of the risk of damage by 5.2.2.4 Colour identification of cores of non-flexible
fire or explosion arising from switch failure. Where a cables
bus-bar section switch is installed, it shall also be
segregated from adjoining banks in the same way [see Function Colour Identification
8-2(5)]. Except main LT panel, it would be preferable of Core of Rubber of
to locate the sub panels/distribution boards near load PVC Insulated Non-
centre. Further, it should beensured that these panels flexible Cable, or of
are easily approachable. The preferable location of Sleeve or Disc to be
panels shall be near the exitways.
Applied to Conductor
or Cable Code
5.2.1.4 It should be possible to isolate any section from
protective or earthing Green and yellow or
the rest of the switchboards such that work might be
Green with yellow
undertaken on this section without the necessity of
stripes 1)
making the switchboard dead. Isolatingused switches
Neutral of a.c. single or three- Black
for the interconnection of sections or for the purpose
phase circuit
of isolating circuit-breakers of other apparatus, shall
also be segregated within its compartment so that no Phase R of 3-phase a.c. circuit Red
live part is accessible when work in a neighboring Phase Y of 3-phase a.c. circuit Yellow
section is in progress. Phase B of 3-phase a,c. circuit Blue

5.2.1.5 In the case of duplicate or ring main supply, Positive of d.c. 2-wire circuit Red
switchgears with interlocking arrangement shall be Negative of d.c. 2-wire ckcuit Black
provided to prevent simultaneous switching of two Outer (positive or negative) of Red
different supply sources. Electrical and/or mechanical d.c. 2-wire circuit derived ffom
interlocks may preferably be provided. 3-wire system
5.2.2 Cables Positive of 3-wire system Red
positive of 3-wire d.c. circuit)
5.2.2.1 The smallest size of the cable that shall be used,
will depend upon the method of laying cable, Middle wire of 3-wire d.c. Black
permissible maximum temperature it shall withstand, circuit
voltage drop over the length of the cable, the Negative of 3-wire d.c. circuit Blue
prospective short-circuit current to which the cable may Functional Earth- Cream
be subjected, the characteristics of the overload Telecommunication
protection gear installed, load cycle and thermal
l]B~e conductorsare also used for earthingand earth continrrity
resistivity of the soil [see also 8-2(6)].
conductors. But it is preferable to use insufated conductors with
NOTE — Guidelines for correlation of the ratings of cables men insulation with vetlow striues.
and characteristics of protective device are under consideration.
Continuous current carrying capacity (thermal limit leading 5.2.2.5 Colour, identification of cores ofjlexible cables
to permanent change in properties of the insulation) under the and flexible cords
installed conditions, voltage drop under required load and the
fault current withstand ability of the cable for the duration
Number of Function of Core Colour(s) of Core
that the protective device controlling the cable installation will
let go the fault current, operating voltage are the prime
Cores
considerations. 1 Phase Brownl)
Neutral (Light) Blue
5.2.2.2 The advice of the cable manufacturer with Protective or Eptlting Green & yellow
regard to installation, jointing and sealing shall be
followed. 2 Phase Brown
Neutral (Light) Bluel)
5.2.2.3 The HV cables shall either be laid on the cable
rack/built-up concrete trenches/tunnel/basement or 3 Phase Brown
directly buried in the ground depending upon the Neutral (Light) Bluel)
specific requirement. It is preferable to use four core Protective or Earthing Green& yellow
cable in place of three and half core to minimize heating 4 or 5 Phase Brown or Blackl)
of neutral core due to harmonic content in the supply Neutral (Light) Bluel)
system and also avoidance of overload failures. All Protective or Earthing Green& yellow
cables shall be installed in accordance with good
practice [8-2(6)]. 1)Certain alternatives are allowed in Wking Regulations.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 17


5.2.3 High Voltage Busbar Trunking/Ducting corridors and shafts for distribution without any false
ceiling as they provide an aesthetically acceptable
High voltage busbar trunking system is a type-tested
finish to merge with other building elements such as
switchgear and control gear assembly in the form of
beams, ducts or pipes in functioned buildings.
an enclosed system. HV bus bar system is used
for transporting power between HV Generators, The class of protection shall be specific depending on
transformers and the infeed main switchgear of the the requirement at the place of installation. Protection
main HV switchgear. class (IP xx) will automatically identify the ventilation,
protection from weather, water, dust etc.
Generally three types of bus ducts namely non-
segregated, segregated and isolated phase bus duct shall In modern building technology, high demands are
be used. The non-segregated bus ducts consists of three made of the power distribution system and its
phase busbars running in a common enclosure made individual components:
of steel or aluminium. The enclosure shall provide
a) Long life and good service quality,
safety for the operational personnel and reduces
b) Safe protection in the event of fire,
chances of faults. The enclosures shall be effectively
grounded. c) Low fire load,
d) Low space requirement, and
Segregated phase bus duct are similar to non-
e) Minimum effort involved in carrying out
segregated phased duct except that metal or insolation
retrofits,
barriers are provided between phase conductors to
reduce chances of phase to phase faults. However, it is The high load density in modern large buildings and ..
preferable to use metal barriers. high rise buildings demands compact and safe solution
In the case of isolated bus ducts, each phase conductor for the supply of power. The use of busbar trunking
shall be housed in a separate non-magnetic enclosures. system is ideal for such applications.
The bus duct shall be made of sections which are Bus bar trunking can be installed in vertical risers ducts
assembled together at site to make complete assembly. or horizontally in passages for transmission and
The enclosure shall be of either round or square shape distribution of power. Busbar tnmking systems allow
and welded construction. The enclosures of all phases electrical installations to be planned in a simple and
in general to be supported on a common steel structure. clear fashion. In the building complexes, additional
Provision of fire protection shall be provided in all safety demands with respect to f~e barriers and fwe
openings in accordance with Part 4 ‘Fire and Life load and use of bus bar trnnking meets this requirement.
Safety’. Fire separation in openings shall be provided
Busbar trunking system reduces the combustible
using materials having 2h fire resistance rating.
material near the area with high energy in comparison
5.2.4 MV/LV Busbar Trunking/Rising Mains with other dkibution systems such as cables and
makes the building safe from the aspect of vulnerability
Where heavy loads are to be carried, busbar systems to fire of electrical origin. In addition, unlike cable
are preferred. The busbars are available for continuous systems the reliability of a bus trunking system is vvery
run from point to point or with tap offs at standard high. These systems also require very little periodic
intervals and have to be chosen as per specific maintenance.
requirement. MV/LV busbar trunking shall be a type-
tested switchgear and control gear assembly in the form Choice of busbar trunking for distribution in buildings
of an enclosed system. There are two types of MV/LV can be made on the basis of
bus duct system for power distribution system: a) reduced fire load (drastically reduced in
comparison to the cable system),
a) Conventional type.
b) reduced maintenance over its entire lifetime,
b) Compact and sandwich type.
c) longer service lifetime in comparison with a
Conventional type bus duct is used for large power cable distribution
handling between transformer and switchgear or
d) enhanced reliability due to rigid bolted
between switchgear and large power loads, such as
joints and terminations and extremely low
compressor drive motor etc. This type is generally used
possibility of insulation failure.
in plant rooms, riser shafts, substations etc.
5.2.5 Transfomners
Compact type is available either air insulated or
sandwich type for use within areas of the building 5.2.5.1 General design objective while selecting the
which are put to other higher (aesthetic) level of use. transformer(s) for a substation would be to provide at
They could be used in false ceiling spaces or even in least two or more transformers, so that a certain amount

18 NATIONAL BUILDING CODE OF INDIA


of’ redundancy is built in, even if a standby system is with appropriate protection. Installations designed for
provided. The total installed transformation capacity parallel operation of transformers shall have protection
would be marginally higher than the anticipated for avoiding circulating current between transformers,
maximum demand. With growing emphasis on energy avoid overload of anyone transformer due to reactance
conservation, the system design is made for both mismatch and the system shall be so arranged as to
extremes of loading. During the periods of lowest load trip the secondary breaker in case the primary breaker
in the system, it would be desirable to operate only of that transformer trips.
one transformer ands witch in additional transformers
as the load variation takes place in a day. The minimum 5.2.6 Switchgear
size of a transformer would quite often depend on the 5.2.6.1 Switchgear (and its protective device) shall
minimum load that is anticipated over a period of about have breaking capacity not less than the anticipated
4 h in a day, Total transformer capacity is generally fault level in the system at that point. System fault level
selected on the basis of present load, possible future at a point in distribution system is predominantly
load, operation and maintenance cost and other system dependent on the transformer size and its reactance.
conditions and selection of the maximum size Parallel operation of transformers naturally increases
(capacity) of the transformer is guided by short-circuit the fault level
making and breaking capacity of the switchgear used
in the medium voltage distribution system. Maximum 5.2.6.2 Isolation and controlling circuit breaker shall
size limitation is important from the aspect of feed to be interlocked so that the isolator caimot be operated
a down stream fault. unless the corresponding breaker is in open condition.
The choice between alternative types of equipment may
For feeding final single phase domestic type of loads be influenced by the following considerations:
or general office loads it is advisable to even use
transformers of capacity much lower than what the a) In certain installaticms supplied with electric
switchgear can handle, so that lower fault MVA is power from remote transformer substations, it
available in such areas and use of hand held equipment may be necessary to protect main circuits with
circuit-breakers operated by earth fault, in
fed through flexible cords is safe.
order to ensure effective earth fault protection.
For reasons of reliability and redundancy it is normal b) Where large electric motors, fimnaces or other
practice to provide at least two transformers for any heavy electrical equipment is installed, the
important installation. Interlinking by tie lines is an main circuits shall be protected from short-
alternative to enhance reliability/redundancy is areas circuits by switch disconnector fuse or
where there are a number of substations in close circuit breakers. For motor protection, the
vicinity, such as a campus with three or four multi- combination of contactor overload device and
storeyed blocks each with a substation. fuse or circuit breakers shall be Type-2 co-
Ring main type of distribution is preferred for ordinated in accordance with accepted
complexes having a number of substations. standards [8-2(7)]. Wherever necessary, back
up protection and earth fault protection shall
5.2.5.2 Where two or more transformers are to be be provided to the main circuit.
installed in a substation to supply a medium voltage
c) Where mean of isolating main circuits is
distribution system, the distribution system shall be
separately required, switch disconnector fuse
divided into separate sections each of which shall be
or switch disconnector may form part of main
normally fed from one transformer only unless the
switchboards.
medium voltage switchgear has the requisite short-
circuit capacity. Provision may, however, be made to 5.2.6.3 It shall be mandatory to provide power factor
interconnect separate sections, through a bus coupler improvement capacitor at the substation bus. Suitable
in the event of failure or disconnection of one capacitor may be selected in consultation with the
transformer. See 4.2 for details of location and capacitor as well as switchgear manufacture depending
requirements of substation. upon the nature of electrical load anticipated on the
system. Necessruy switchgear/feeder circuit breaker
The transformers, that may at any time operate in
shall be provided for controlling of capacitor bank.
parallel, shall be so selected as to share the load in
proportion to their respective load ratings. While the Power factor of individual motor maybe improved by
general practice is to avoid operation of transformers connecting individual capacitor banks in parallel. For
in parallel for feeding final distribution in buildings, it higher range of motors, which are running continuously
is possible to use transformers with slightly different without much variation in load, individual power factor
impedance or voltage taps to operate in parallel, but correction at load end is advisable.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIRD INSTALLATIONS 19


NOTE — Care should be taken in deciding the kVA rating of 5.3 Reception and Distribution of Main Supply
the capacitor in relation to the magnetizing kVA of the motor.
Over rating of the capacitor may cause injury to the motor and 5.3.’1 Control at Point of Commencement of Supply
capacitor bank. The motor still rotating after disconnection
5.3.1.1 There shall be a circuit-breaker or miniature
from the supply, may act as generator by self-excitation and
produce a voltage higher than supply voltage. If the motor is circuit-breakers or a load break switch fuse on each
again switched on before the speed has fallen to about live conductor of the supply mains at the pointof entry.
80 percent of the normal running speed, the high voltage will The wiring throughout the installation shall be such
be superimposed on the supply circuits and will damage both
that there is no switch or fuse unit in the earthed neutral
the motor and capacitor.
of conductor. The neutral shall also be distinctly
As a general rule, the kVAr rating of the capacitor marked. In this connection, Rule 32(2) and Rule 50(1)
should not exceed the no-load magnetizing kVA of of the Indian Electricity Rules, 1956 (see Annex B) as
the motor. amended up to date shall also be referred.

Generally it would be necessary to provide an 5.3.1.2 The main switch shall be easily accessible and
automatic control for switching in capacitors matching situated as near as practicable to the termination of
the load power factor and the bus voltage. Such a service line.
scheme would be necessary as capacitors permanently 5.3.1.3 On the main switch, where the conductors
switched in the circuit may cause overvoltage at times include an earthed conductor of a two-wire system or
of light load. an earthed neutral conductor or a multi-wire system or
5.2.6.4 Sufficient additional space shall be allowed in a conductor which is to be connected thereto, an
substations and switchrooms to allow operation and indication of a permanent nature shall be provided to
maintenance and proper means shall be provided for identify the earthed neutral conductor. In this
isolating the equipment to allow access for servicing, connection, Rule 32( 1) of Indian Electricity Rules,
testing and maintenance. Sufficient additional space 1956 (see Annex B) shall be referred as amended up-
shall be allowed for temporary location and installation to-date.
of standard servicing and testing equipment. Space 5.3.1.4 Energy meters
should also be allowed to provide for anticipated future
Energy meters shall be installed in residential buildings
extensions.
at such a place which is readily accessible to the owner
5.2.6.5 Electrical installations in a room or cubicle or of the building and the Authority. These should be
in an area surrounded by wall fence, access to which installed at a height where it is convenient to note the
is controlled by lock and key shall be considered meter reading, it should preferably not be installed
accessible to authorized persons only. below one metre from the ground. The energy meters
A wall or fence less than 1.8 m in height shall not be should either be provided with a protecting covering,
considered as preventing access unless it has other enclosing it completely except the glass window
features that provide a degree of isolation equivalent through which the readings are noted or should be
to a 1.8 m fence. mounted inside a completely enclosed panel provided
with hinged or sliding doors with arrangement for
5.2.6.6 Harmonics on the supply systems are locking.
becoming a greater problem due to the increasing use
In multi-storeyed buildings meters shall be installed
of electronic equipments, computer, fluorescent,
with tapping point for meters of the rising main (bus
mercury vapour and sodium vapour lighting, controlled
trunking) on individual floors.
rectifier and inverters for variable speed drives, power
electronics and other non-linear loads. Harmonics may 5.3.2 Main Switches and Switchboard
lead to almost as much current in the neutral as in the
5.3.2.1 All main switc~~s shall be either of metal-clad
phases. This current is almost entirely third harmonic.
enclosed pattern or of any insulated enclosed pattern
Phase rectification devices may be considered for the
which shall be fixed at close proximity to the point
limits of harmonic voltage distortion may be
of entry of supply. Every switch shall have an
considered at the planning stage in such cases.
environmental protection level rating (1P), so that its
With the wide spread use of thyristor and rectifier based operation is satisfactory in the environment of the
loads there is necessity of providing a full size neutral; installation.
but this requirement is limited to the 3-phase 4-wire NOTE — Wc@work shalt not be used for the construction or
distribution generally in the 400/230 V system. As a mounting of switches and syheh boards instafled in’a building.
result it is not desirable to use half-size neutral
5.3.2.2 Location
conductor, as possibility of neutral conductor overload
due to harmonics is likely. a) The location of the main board should be such

20 NATIONAL BUILDING CODE OF INDIA


that it is easily accessible for fireman and be protected by a rubber or wooden bush
other personnel to quickly disconnect the at the entry hole. The earth stud should
supply in case of emergencies. If the room is commensurate with the size of earth lead/
locked for security, means of emergency leads. Alternatively, metal boards may be
access, by schemes such as break glass made of suitable size angle iron of minimum
cupboard, shall reincorporated. size 35 mm x 35 mm x 6 mm or channel iron
b) Main switch board shall be installed in rooms of minimum size 35 mm x 25 mm x 6 mm
or cupboards so as to safeguard against frames work suitably mounted on front with
operation by unauthorized personnel. a 3 mm thick mild steel plate and on back with
c) Switchboards shall be placed only in dry 1.5 mm thick mild steel sheet. No apparatus
situations and in ventilated rooms and they shall project beyond any edge of panel. No
shall not be placed in the vicinity of storage fuse body shall be mounted within 2.5 cm of
batteries or exposed to chemical fumes. any edge of the panel.
NOTE — Such type of boards are particularly suitable
d) In damp situation or where inflammable or
for small switchboard for mounting metal-clad
explosive dust, vapour or gas is likely to be switchgear connected to supply at low voltages.
present, the switchboard shall be totally
b) Fixed-type metal boards — These shall
enclosed and shall have adequate degree
consist of an angle or channel iron frame fixed
of protection. In some cases flameproof
on the wall or on floor and supported on the
enclosure may be necessitated by particular
wall at the top, if necessary. There shall be
circumstances [see 8-2(8)].
a clear distance of 1 m in front of the
e) Switchboards shall not be erected above gas switchboards. If there are any attachments
stoves or sinks, or within 2.5 m or any of bare connections at the back of the
washing unit in the washing rooms or switchboard Rule 5 l(l)(c) of Indian Electrkity
laundries, or in bathrooms, lavatories or Rules, 1956 shall apply. The connections
toilets, or kitchens. between the switchgear mounting and the
f) In case of switchboards unavoidably fixed in outgoing cable up to the wall shall be enclosed
places likely to be exposed to weather, to drip, in a protection pipe.
or to abnormal moist temperature, the outer NOTE — Such type of boards are particularly suitable
casing shall be weatherproof and shall be for large switchboards for mounting large number of
provided with glands or bushings or adopted switchgears or high capacity metal-clad switchgear or
to receive screwed conduit, according to the both.

manner in which the cables are run. c) Protected-type switchboard — A protected


Adequate illumination shall be provided for switchboard is one where all of the conductors
g)
all working spaces about the switchboards are protected by metal or other enclosures.
when installed indoors. They may consist of a metal cubicle panel, or
an iron frame upon which is mounted metal-
5.3.2.3 Metal-clad switchgear shall preferably be clad switchgear. They usually consist of a
mounted on any of the following types of boards: main switch, busbars and circuit breakers or
a) Hinged-type metal boards — These shall fuses controlling outgoing circuits.
consist of a box made of sheet metal not less d) Open-type switchboard — An open type
than 2 mm thick and shall be provided with a switchboard is one, which has exposed current
hinged cover to enable the board to swing carrying parts on the front of the switchboard.
open for examination of the wiring at the back. This type of switchboard is rarely used now-
The joints shall be welded. There shall be a a-days but wherq this exists, a hand rail
clear distance of not less than 2.5 cm between or barrier has to’ be provided to prevent
the teak wood board and the cover, the unintentional or accidental contact with
distance being increased for larger boards in exposed live parts. They must be located in a
order that on closing of the cover, the special switch room or enclosure and only a
insulation of the cables is not subjected to competent person may have access to these
damage and no excessive twisting or bending switchboards.
in any case. The board shall be securely fixed NOTE — These boards may be existing in old
to the wall by means of rag bolts, plugs, or installations. It is recommended that they be phased
wooden plugs and shall be provided with a out. Whh the continuously increasing fault power feed
due to increases in generation and strengthening of
locking arrangement and an earthing stud. All distribution systems, these open boards are a source of
wires passing through the metal board shall accidents.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 21


5.3.2.4 Recessing of boards 5.3.2.8 MVZLV Busbar chambers (400 W230 V)

Where so specified, the switchboards shall be recessed Busbar chambers, which feed two or more circuits,
in the wall. Ample room shall be provided at the back must be conti-oiled by a main disconnector (’W & N),
for connection and at the front between the switchgear or Isolating ~nks or TPN MCB to ‘enable them to be
mountings. disconnected from the supply.

5.3.2.5 Marking of apparatus [see also 8-2(9)] 5.3.3 Distribution Boards

a) Where aboard is connected to voltage higher A distribution board comprises of one or more protective
than 250 V, all the apparatus mounted on it devices against over current and ensuring the distribution
shall be marked on the following colours to of electrical energy to the circuits. Distribution board
indicate the different poles or phases to which shall provide plenty of wiring space, to allow working
the apparatus or its different terminals may as well as to allow keeping the extra length of connecting
have been connected: cables, likely to be required for maintenance.
Alternating Current Direct Current 5.5.3.1 Main distribution board shall be provided with
Three-phases — red, Three-wire system a circuit breaker on each pole of each circuit, or a switch
yellow, blue — 2 outer wire, with a fuse on the phase or live conductor and a link
positive red and on the neutral or earthed conductor of each circuit. The
negative blue switches shall always be linked.
1 Neutral — black 1 Neutral — black All incomers should be provided with surge protection
Where four-wire three-phase wiring is done, devices. .-
the neutral shall be in one colour and the other 5.3.4 Branch Distribution Boards
three wires in another colour as mentioned
above or shall be suitably tagged or sleeved 5.3.4.1 Branch distribution boards shall be provided,
for fool proof identification. along with earth leakage protective device (ELCB)
(incoming), with a fuse or a miniature circuit breaker
b) Where aboard has more than one switch, each
or both of adequate rating/setting chosen on the live
such switch shall be marked to indicate which
conductor of each sub-circuit and the earthed neutral
section of the installation it controls. The main
conductor shall be connected to a common link and be
switch shall be marked as such and where
capable of being disconnected individually for testing
there is more than one main switch in the
purposes. At least one spare circuit of the same capacity
building, each such switch shall be marked
shall be provided on each branch distribution board.
to indicate which section of the installation it
Further, the individual branching circuits (outgoing)
controls.
shall be protected against over-current with miniature
All markings shall be clear and permanent. circuit breaker of adequate rating. In residential/
industrial lighting installations, the various circuits
5.3.2.6 Drawings
shall be separated and each circuit shall be individually
Before proceeding with the actual construction, a protected so that in the event of fault, only the particular
proper drawing showing the detailed dimensions and circuit gets disconnected.
design including the disposition of the mountings of
5.3.4.2 Circuits shall be separate for installations at
the boards, which shall be symmetrically and neatly
higher level such as those in the ceiling and at higher
arranged for arriving at the overall dimensions, shall
levels, above 1 m, on the walls and for installations at
be prepared along the building drawing. Such drawings
lower level such as sockets for portable or stationery
will show the mandatory clearance spaces if any, and
plug in equipments. For d~vices consuming high power
clear height below the soffit of the beam required to
and which are to be supplied through supply cord and
satisfy regulations and safety considerations, so that
plug, separate wiring shall be done. For plug-in
other designers or installers do not get into such areas
equipment provisions shall be made for providing
or spaces for their equipment.
ELCB protection in the distribution board.
5.3.2.7 Where aboard has more than one switch, each
5.3.4.3 It is preferable to have additional circuit for
such switch shall be marked to indicate which section
kitchen and bathrooms. Such sub-circuit shall not have
of the installation it controls. The main switch shall be
more than a total of ten points of light, fans and 6A
marked as such and where there is more than one main
socket outlets. The load of such circuit shall be
switch in the building, each such switch shall be marked
restricted to 800 W. If a separate fan circuit is provided,
to indicate which section of the installation it controls.
the number of fans in the circuit shall not exceed ten.
All markings shall be clear and permanent. Power sub-circuit shall be designed according to the

22 NATIONAL BUILDING CODE OF INDIA


load but in no case shall there be more than two 16A reset of protective devices, and shall not be
outlets on each sub-circuit. more than 1.8 m from floor level.

5.3.4.4 The circuits for lighting of common area shall c) These shall be of either metal-clad type, or
be separate. For large halls 3-wire control with individual air insulated type. But, if exposed to weather
control and master control installed near the entrance or damp situations, these shall be of the
shall be provided for effective conservation of energy. weatherproof type and, if installed where
exposed to explosive dust, vapour or gas,
5.3.4.5 Where daylight would be available, particularly these shall be of flameproof type in
in large halls, lighting in the area near the windows, accordance with accepted standards [8-2(10)].
likely to receive daylight shall have separate controls In corrosive atmospheres, these shall be
for lights, so that they can be switched off selectively treated with anti-comosive preservative or
when daylight is adequate, while keeping the lights in covered with suitable plastic compound.
the areas remote from the windows on. d) Where two and/or more distribution boards
5.3.4.6 Circuits for socket outlets may be kept separate feeding low voltage circuits are fed from a
circuits feeding fans and lights. Normally, fans and supply of medium voltage, the metal case shall
lights may be wired on a common circuit. In large be marked ‘Danger 415 V’ and identified with
spaces circuits for fans and lights may also be proper phase marking and danger marks.
segregated. Lights may have group control in large e) Each shall be provided with a circuit list
halls and industrial areas. While providing group giving diagram of each circuit which it
control consideration may be given for the nature of controls and the current rating of the circuit
use of the area lit by a group. Consideration has to be and size of fuse element.
given for the daylight utilization, while grouping, so f-) In wiring branch distribution board, total load
that a group feeding areas receiving daylight can be of consuming devices shall be divided as far
selectively switched off during daylight period. as possible evenly between the number of
5.3.4.7 The load on any low voltage sub-circuit shall ways in the board leaving spare circuits for
not exceed 3000 W. In case of a new installation, all future extension.
circuits and sub-circuits shall be designed with an initial 5.3.6 Protection of Circuits
load of about 2500 W, so as to allow a provision of 20
a) Appropriate protection shall be provided at
percent increase in load due to any future modification.
switchboards, distribution boards and at all
Power sub-circuits shall be designed according to the
levels of panels for all circuits and sub-circuits
load, where the circuit is meant for a specific
against short circuit, over-current and other
equipment. Good practice is to limit a circuit to a
parameters as required. The protective device
maximum of four sockets, where it is expected that
shall be capable of interrupting maximum
there will be diversity due to use of very few sockets
prospective short circuit current that may
in large spaces (example sockets for use of vacuum
occur, without danger. The ratings and
cleaner). General practice is to limit it to two sockets
settings of fuses and the protective devices
in a circuit, in both residential and non-residential
shall be co-ordinated so as to afford selectivity
buildings and to provide a single socket on a circuit
in operation and in accordance with accepted
for a known heavy load appliance such as air
standards [8-2(1)].
conditioner, cooking range etc.
b) Where circuit-breakers are used for protection
5.3.4.8 In wiring installations at special places like of a main circuit and of the sub-circuits
construction sites, stadium, shipyards, open yards in derived therefrom, djscritnination in operation
industrial plmts, etc, where a large number of high may be achieved by adjusting the protective
wattage lamp may be required, there shall be no devices of the sub-main circuit-breakers to
restriction of load on any circuit but conductors used operate at lower current settings and shorter
in such circuits shall be of adequate size for the load time-lag than the main circuit-breaker.
and proper circuit protection shall be provided.
c) Where HRC type fuses are used for back-up
5.3.5 Location of Distribution Boards protection of c~cuit-breakers, or where HRC
fuses are used for protection of main circuits,
a) The distribution boards shall be located as and circuit-breakers for the protection of sub-
near as possible to the centre of the load they circuits derived there from, in the event of
are intended to control. short-circuits protection exceeding the short-
b) These shall be fixed on suitable stanchion or circuits capacity of the circuit-breakers, the
wall and shall be accessible for replacement HRC fuses shall operate earlier than the

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 23


circuit-breakers; but for smaller overloads 5.5.3 The current ratings of isolators and normal duty
within the short-circuit capacity of the circuit- switches and composite units of switches and fuses
breakers, the circuit-breakers shall operate shall be selected from one of the following values:
earlier than the HRC fuse blows.
16,25,32,63, 100,160,200,320,400, 500,630,
d) If rewireable type fuses are used to protect 800, 1000 and 1 250A.
sub-circuits derived from a main circuit
protected by HRC type fuses, the main circuit 5.5.4 The ratings of rewirable and HRC fuses shall be
fuse shall normally blow in the event of a in accordance with good practice [8-2(13)].
short-circuit or earth fault occurring on sub-
5.5.5 The current ratings of miniature circuit-breakers
circuit, although discrimination may be
shall be chosen from the values given below:
achieved in respect of overload currents. The
use of rewireable fuses is restricted to the 6,8,10,13,16,20,25,32, 40,50,63,80,100 and
circuits with short-circuit level of 4 kA; for 125 A.
higher level either cartridge or HRC fuses
5.5.6 The current ratings of moulded case circuit-
shall be used. However, use of rewireable fuse
breakers shall be chosen from the values given
is not desirable, even for lower fault level
below:
areas. MCB’s provide a better and dependable
protection, as their current setting is not 100,125,160,200,250, 315,400,630,800,1000,
temperable. 1250 and 1600A.
e) A fuse carrier shall not be fitted with a fuse
5.5.7 The current ratings of air circuit-breakers shall.
element larger than that for which the carrier
be chosen from the values given below:
is designed.
The current rating of a fuse shall not exceed 630,800,1000,1250,1600,2 000,2500,3200
f)
the current rating of the smallest cable in the and4000A.
circuit protected by the fuse. 5.5.8 The current ratings of the distribution fuse board
g) Every fuse shall have its own case or cover shall be selected from one of the following values:
for the protection of the circuit and an
indelible indication of its appropriate current 6, 16,25,32,63 and 100A.
rating in an adjacent conspicuous position.
5.6 Installation Circuits
5.4 Voltage and Frequency of Supply
Type of Circuit Wire Size Number of Cixuits
It should be ensured that all equipment connected to
Lighting 1.0 mm2 2 or more
the system including any appliances to be used on it
Socket-outlets 10A 2.5 mm2 Any number
are suitable for the voltage and frequency of supply of
An?as such as
the system. The nominal values of low and medium
kitchens and
voltage systems in India are 240 V and 415 V ac, laundries 3x
respectively, and the frequency 50 Hz. double socket-
outlets per circuit.
NOTES
Other areas up to
1 The design of the wiring system and the sizes of the cables 12 double socket-
should be decided taking into account two factors:
outlets
a) VoltageDrop — This should be kept as low as economy
Socket-outlets 15 or 2.5 rnmz 1
permits to ensure proper functioning of all electrical
20A
appliances and equipment including motors; and
b) First cost against operating losses. Water heater 3 kW ~.5 mm2 1
Water heater 3-6 kW 2.5 mm2 1
2 In view of the latest development at the international level,
nominal system voltages have been aligned with IEC Free standing electric 6.0 mm2 1
recommendation and accordingly the nominal ac system range
voltage shall be changed from 240/415 V to 230/400 V with a Separate oven and/ 4.0 mm2 1
tolerance of * 10 percent. or cook top
5.5 Rating of Cables and Equipments Permanently connec- 2.5 mmz 1 above 10 A. Up
ted appliances tolOA canbe
5.5.1 The current-carrying capacity of different types including dish- wired aspart ofa
of cables shall be chosen in accordance with good washers, heaters, etc socket-outlet circuit
practice [8-2(12)]. S:bmains to garage 2.5 mmz 1 for each
or out-building
5.5.2 The current ratings of switches for domestic and 16 mm2 1
Mains cable
similar purposes are 6A and 16A.

24 NATIONAL BUILDING CODE OF INDIA


5.6.1 Selecting and Installing Cables

5.6.LI Cable insulation types

For the mains cable Tough plastic sheathed (TPS) cable


For installation wiring Tough plastic sheathed (TPS) cables
For main earth or main equipotential wire Polyvinyl chloride (PVC) insulated conduit wire
Underground installation and installation in cable PVC insulated, PVC sheathed armoured cables or
trench, feeders between buildings etc., XLPE insulated, PVC sheathed cables armoured cables
Installation in plant rooms, switch rooms etc, on PVC insulated, PVC sheathed or XLPE insulated,
cable tray or ladder or protected trench, where risk PVC sheathed unarmored cables
of mechanical damage to cable does not exist.

For the purposes of this Code cables above 1 mmzmust suitable location that requires no additional protection.
have stranded conductors. All cables when installed, The cables for wiring circuits in electrical installation
must be adequately protected against mechanical must have the appropriate wire size matching the
damage. This can be carried out by either having requirement of the loads and the following table gives
additional protection, such as being enclosed in PVC the recommendations for different types of loads.
conduit or metal pipes, or placing the cables in a

5.6.1.2 Circuit wire sizes

Circuits Minimum Wire Size Wire Colour


1-way lighting 2 + E cable wires 1.5 mmz Red-Black-Green or Green/Yellow
2-way lighting control (straps 3-wire cable 1.5 mm2 Red-White-Blue
between the 2 switches)
Storage water heaters up to 3 kW 2 + E cable 1.5 mm2 (stranded Red-Black-Green or Green/Yellow
conductors)
Storage water heaters between 2 + E cable 2.5 mm2 (stranded Red-Black-Green or Green/Yellow
3kWand6kW conductors)
Socket-outlets and permanent 2 + E cable 2.5 mmz (stranded Red-Black-Green or Green/Yellow
connection units conductors)
Submains to garages or out 2 + E cable 2.5 mm2 (stranded Red-Black-Green or Green/Yellow
buildings conductors)
Cooking bobs 2 + E cable 4 mm2 Red-Black-Green or Green/Yellow
Separate ovens 2 + E cable 4 mm2 (stranded
conductors)
Electric range 2 + E cable 6 mm2 (stranded Red-Black-Green or Green/Yellow
conductors)
Mains 2 wire cable 16 mm2 (stranded Red-Black
conductors)
Main equipotential bonding wire Conduit wire 4 mm2 (stranded Green or G&n/Yellow
conductors)
Main earth wire Conduit wire 6 mm2 (stranded Green or Green/Yellow
conductors)

2+ Eisalsoknown astwinandearth

Switch or isolator controlling a water heater or geyser the entrance and provide an indication at the water
should not be located within 1 m from the location of heater. A socket or a connector block with suitable
a shower or bath tub, to avoid a person in wet condition protection against water spray should be provided to
reaching the switch or isolator. It is preferable to connect the water heater. The above considerations
provide the control switch outside the bathroom near apply to switches for outdoor lights and other

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 25


appliances, with the object of avidance of operation of 5.7.2 Future Demand
a switch when a person is wet. Sockets in kitchen,
However, if for financial reasons, it is not possible to
bathroom, toilet, garage etc, should not be provided
provide alighting installation to give the recommended
within a height of 1 m from the ground level. Similar
illumination levels, the wiring installation at least
care has to be taken for installations involving
should be so designed that at a later date, it will permit
fountains, swimming pools etc. Light fittings in such
the provision for additional lighting fittings or
areas should be fed at low voltage, preferably through
conversion from incandescent to fluorescent lighting
an isolating transformer with a proper earth leakage
fittings to bring the installation to the required standard.
protection.
It is essential that adequate provisions should be made
5.6.2 Requirements for Physical Protection of for all the electrical services which may be required
Underground Cables immediately and during the intended useful life of the
building.
Protective Element Specifications
5.7.3 Principles of Lighting
Bricks a) 100 mm minimum width
b) 25 mm thick When considering the function of artificial lighting,
c) sand cushioning 100 mm attention shall be given to the following principle
and sand cover 100 mm. characteristics before designing an installation:
Concrete slabs at least 50 mm thick.
a) illumination and its uniformity;
Plastic slabs at least 10 mm thick, b) special distribution of light. This includes a
(polymeric cover depending on properties and
reference to the composition of diffused and
strips) Fibre has to be matched with the
directional light, direction of incidence, the
reinforced plastic protective cushioning and
distribution of luminance and the degree of
cover
glare; and
PVC conduit or The pipe diameter should be
c) colour of the light and colour rendition.
Pvc pipe or such so that the cable is able
stoneware pipe or to easily slip down the pipe. 5.7.4 The variety of purposes which have to be kept
hume pipe in mind while planning the lighting installation could
Galvanized pipe The pipe diameter should be be broadly grouped as:
such so that the cable is able a) industrial buildings and processes;
to easily slip down the pipe.
b) offices, schools and public buildings;
The trench shall be backtllled to cover the cable initially c) surgeries and hospitals; and
by 200 mm of fill; and then a plastic marker strip over d) hostels, restaurants, shops and residential
the full length of cable in the trench. Fill the trench buildings.
shall be laid before filling the full trench. The marker
5.7.4.1 It is important that appropriate levels of
signs where any cable enters or leaves a building shall
illumination for these and the types and positions of
be put. This will identify that there is a cable located
fittings determined to suit the task and the disposition
underground near the building. If the cables rise above
of the working planes.
ground to enter a building or other structure, a
mechanical protection such as a GI pipe or PVC pipe 5.7.5 For specific requirements for lighting of special
for the cable from the trench depth to a height of 2.0 m occupancies, reference shall be made to good practice
above ground shall be provided. [8-2(14)].

5.7.6 Energy Conservation


5.7 Lighting and Levels of Illumination
Energy conservation may be achieved by using the
5.7.1 General
following:
Lighting installation shall take into consideration the
many factors on which the quality and quantity of a) Energy efficient lamps, chokes, ballast, etc
for lighting equipment.
artificial lighting depends. The modern concept is to
provide illumination with the help of a large number b) Efficient switching systems such as remote
of light sources not of higher illumination level. Also sensors, infrared switches, master switches,
much higher levels of illumination are called for, than remote switches, etc for switching ON and
in the past, often necessitating the use of fluorescent OFF of lighting circuits.
lighting suitably supplemented with incandescent c) Properly made/connected joints/contacts to
fittings, where required. avoid loose joints leading to loss of power.

26 NATIONALBUILDINGCODE OF INDIA
~ ._ . ....

5.8 In locations where the system voltage exceeds buildings, reference may be made to good practice
650 V, as in the case of industrial locations, for [8-2(16)].
details of design and construction of wiring
A typical distribution scheme in a residential building
installation, reference may be made to good practice
with separate circuits for lights and fans and for power
[8-2(15)].
appliances is given in Fig. 1.
5.9 Guideline for Electrical Layout in Residential
5.10 For detailed information regarding the installation
Buildings
of different electrical equipments, reference may be
For guidelines for electrical installation in residential made to good practice [8-2(17)].

5A SWITCH .
SOCKET OUTLET

G
FAN SWITCH
OUTLET

5A SWITCH

w
5A SWITCH
SOCKET OUTLET
.-

F Q’
FAN SWITCH
OUTLET

1 J

2 -WAY SWITCH OUTLET I 15A SWITCH


SOCKET OUTLET
l-l IAJ

__L--- J, , 1

.-.
15A SWITCH
I SOCKET OUTLET

—.i, I II
.-—.———.— .— —.-..
—
—
-’
h I NEUTRAL BUS
.——.. ——.
3
I I

DISTRIBUTION BOA IRD


/ FOR THE FLAT

EARTH BUS 1
L MCB’S

NL
E

FIG. 1 WIRING DIAGRAMFORA TYPICALDISTRIBUTIONBOARDSCHEME


IN A RESIDENTIAL BUILDING FLAT

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 27


6 WIRING current which the circuit is designed to carry. In each
circuit or sub-circuit the fuse shall be selecttxj to match
6.1 Provision for Maximum Load
the cable rating to ensure the desired protection.
All conductors, switches and accessories shall be of
such size as to be capable of carrying, without their 6.3 Branch Switches
respective ratings being exceeded, the maximum Where the supply is derived from a three-wire or four-
current which will normally flow through them. wire source, and distribution is done on the two-wire
6.1.1 Estimation of Load Requirements system, all branch switches shall be placed in the outer
or live conductor of the circuit and no single phase
In estimating the current to be carried by any conductor switch or protective device shall be inserted in the
the following ratings shall be taken, unless the actual middle wire, earth or earthed neutral conductor of the
values are known or specified for these elements: circuit. Single-pole switches (other than for multiple
control) carrying not more than 16A may be of tumbler
Element Rating (in W)
type or flush type which shall be on when the handle
Incandescent lamps 60 or knob is down.
Ceiling fans
100
Table fans } 6.4 Layout and Installation Drawing
Ordinary socket outlet points 100
6.4.1 The electrical layout should be drawn indicating
Fluorescent tubes:
properly the locations of all outlets for lamps, fans,
Length: 600 mm 25
appliances both fixed and transportable, motors, etc,
1200 mm 50
and best suit for wiring. .—
1500 mm 90
Power socket-outlet 1000 6.4.2 All runs of wiring and the exact positions of all
Air-conditioner 2500 points of switch-boxes and other outlets shall be first
marked on the plans of the building and approved by
6.1.2 Electrical installation in a new building shall
the engineer-in-charge or the owner before actual
normally begin immediately on the completion of the
commencement of the work.
main structural building work and before finishing
work such as plastering has begun except in the case 6.4.3 Industrial layout drawings should indicate the
of surface wiring which can be carried out after the relative civil and mechanical details.
plaster work. Usually, no installation work should start
until the building is reasonably weatherproof, but 6.4.4 Layout of Wiring
where electric wiring is to be concealed within the The layout of wiring should be designed keeping in
structures as maybe the case with a reinforced concrete view disposition of the lighting system to meet the
building, the necessary conduits and ducts shall be illumination levels. All wirings shall be done on the
positioned firmly by tying the conduit to the distribution system with main and branch distribution
reinforcement before concreting. When shutters are boards at convenient physical and electrical load
removed after concreting, the conduits ends shall be centres. All types of wiring, whether concealed or
given suitable anti-corrosive treatment and holes unconcealed should be as near the ceiling as possible.
blocked off by putties or caps to protect conduits from In all types of wirings due consideration shall be given
getting blocked. All conduit openings and junction box
for neatness and good appearance.
openings, etc shall be properly protected against entry
of mortar, concrete, etc during construction. 6.4.5 Balancing of circuits in three-wire or poly-phase
installation shall be arranged before hand. Proper
6.2 Selection of Size of Conductors
Balancing can be done only under actual load
The size of conductors of circuits shall be so selected conditions. Conductors shall be so enclosed in earthed
that the drop in voltage from consumer’s terminals in metal or incombustible insulating material that it is not
a public supply (or from the busbars of the main possible to have ready access to them. Means of access
switchboard controlling the various circuits in a private shall be marked to indicate the voltage present.
generation plant) to any point on the installation does
Where terminals or other fixed live parts between
not exceed three percent of the voltage at the
which a voltage exceeding 250 V exists are housed in
consumer’s terminals (or at two busbars as these may
separate enclosures or items of apparatus which,
be) when the conductors are carrying the maximum
although separated are within reach of each other, a
current under the normal conditions of service.
notice shall be placed in such a position that anyone
6.2.1 If the cable size is increased to avoid voltage gaining access to live parts is warned of the magnitude
drop in the circuit, the rating of the cable shall be the of the voltage that exists between them.

28 NATIONAL BUILDING CODE OF INDIA


Where loads are single phase, balancing should be for 6.5.5 Connection to Ancillary Buildings
the peak load condition based on equipment usage.
Unless otherwise specified, electric connections to
Facility for change should be built into the distribution
ancillary buildings, such as out-houses, garages, etc,
design.
adjacent to the main building and when no roadway
NOTE— The aboverequirementsapplyequallyto three-phase intervenes shall be taken in an earthed GI pipe or heavy
circuits in which the voltage between lines or to earth exceeds duty PVC or HDPE pipe of suitable size in the exposed
250 V and to groups of two or more single-phase circuits,
between which medium voltage may be present, derived
portion at a height of not less than 5.8 m or by buried
therefrom. They apply also to 3-wire dc or 3-wire single-phase underground cables. This applies to both runs of mains
ac circuits in which the voltage between lines or to earth or sub-mains or final sub-circuit wiring between the
exceeds 250 V and to groups of 2-wire circuits, between which buildings.
medium voltage may be present, derived therefrom.
6.5.6 Expansion Joints
6.4.6 Medium voltage wiring and associated apparatus
shall comply, in all respects, with the requirements of Distribution boards shall be so located that the conduits
Rules 50, 51 and 61 of the Indian Electricity Rules, shall not normally be required to cross expansion joints
1956 as amended up-to-date. in a building. Where such crossing is found to be
unavoidable, special care shall be taken to ensure that
6.5 Conductors and Accessories the conduit runs and wiring are not in any way put to
6.5.1 Conductors strain or damaged due to expansion of building
structure. Anyone of the standard methods of
Conductors for all the internal wiring shall be of connection at a structural expansion joint shall be
copper. Conductors for power and lighting circuits shall followed:
be of adequate size to carry the designed circuit load
without exceeding the permissible thermal limits for a) Flexible conduit shall be inserted at place of
the insulation. The conductor for final sub-circuit for expansion joint.
fan and light wiring shall have a nominal cross- b) Oversized conduit overlapping the conduit.
sectional area not less than 1.50 mm2 copper. The c) Expansion box.
cross-sectional area of conductor for power wiring shall
6.5.7 Low Voltage (Types of Wires/Cables)
be not less than 4.0 mmz copper. The minimum cross-
sectional area of conductor of flexible cord shall be Low voltage services utilizes various categories of
1.50 mm2 copper. cables/wires, such as Fibre optic cable, co-axial,
CAT 5, etc. These shall be laid at atleast minimum
In existing buildings where aluminium wiring has been
specified distance of 300 mm from any power wire or
used for internal electrification, changeover from
cable. Special care shall be taken to ensure that the
aluminium conductor to copper conductor may be
conduit runs and wiring are laid properly for low
made once the former goes beyond economical repairs.
voltage signal to flow through it.
NOTE — It is advisable to replace wiring, which is more than
30 years old as the insulation also would have deteriorated, 6.6 Joints and Looping Back
and will be in a state to cause failure on the slightest of
mechanical or electrical disturbance. 6.6.1 Where looping back system of wiring is
specified, the wiring shall be done without any junction
6.5.2 Flexible Cables and Flexible Cords or connector boxes on the line. Where joint box system
Flexible cables and cords shall be of copper and is specified, all joints in conductors shall be made by
stranded and protected by flexible conduits or tough means of suitable mechanical connectors in suitable
rubber or PVC sheath to prevent mechanical damage. joint boxes. Wherever practicable, looping back system
should be preferred. Whmever practicable, only one
6.5.3 Cable Ends system shall be adopted for a building, preferably a
When a stranded conductor having a nominal sectional looping back system.
area less than 6 mm2 is not provided with cable sockets, 6.6.2 In any system of wiring, no bare or twist joints
all strands at the exposed ends of the cable shall be shall be made at intermediate points in the through run
soldered together or crimped using suitable sleeve or of cables unless the length of a final sub-circuit, sub-
ferrules. main or main or more than the length of the standard
coil as given by the manufacturer of the cable. If any
6.5.4 Special Risk
jointing becomes unavoidable such joint shall be made
Special forms of construction, such as flameproof through proper cutouts or through proper junction
enclosures, shall be adopted where there is risk of the boxes open to easy inspection, but in looping back
fire or explosion. system no such junction boxes shall be allowed.

PART S BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 29


6.6.3 Joints are a source of problems in reliability and Flexible cords shall be so connected to devices and to
are also vulnerable to fire. They should be avoided or fittings that tension will not be transmitted to joints or
at least minimized. Where joints in cable conductors terminal screws. This shall be accomplished by a knot
or bare conductors are necessary, they shall be in the cord, by winding with tape, by a special fitting
mechanically and electrically sound. Joints in non- designed for that purpose, or by other approved means
flexible cables shall be accessible for inspection; which will prevent a pull on the cord from being
provided that this requirement shall not apply to joints directly transmitted to joints or terminal screws.
in cables buried underground, or joints buried or
enclosed in non-combustible building materials. Joints 6.7 Passing Through Walls and Floors
in non-flexible cables shall be made by soldering, 6.7.1 Where conductors pass through walls, one of the
brazing, welding or mechanical clamps, or be of the following methods shall be employed. Care shall be
compression type; provided that mechanical clamps taken to see that wires pass freely through protective
shall not be used for inaccessible joints buried or pipe or box and that the wires pass through in a straight
enclosed in the building structure. All mechanical line without any twist or cross in wires on either ends
clamps and compression type sockets shall securely of such holes:
retain all the wires of the conductors. Any joint in a
flexible cable of flexible cord shall be effected by a) The conductor shall be carried either in a rigid
means of a cable coupler. steel conduit or a rigid non-metallic conduit
conforming to accepted standards [8-2(18)].
For flexible cables for small loads less than 1 kW, while
b) Conduit colour coding
it would be desirable to avoid joints, if unavoidable,
The conduits shall be colour coded as per the
joints can be made either by splicing by a recognised
purpose of wire carried in the same. The
method or by using a connector and protecting the joint
colour coding may be in form of bands of
by suitable insulating tape orsleeve or straight joint.
colour (4 inch thick, with centre-to-centre
For application of flexible cable for loads of 1 kW or
distance of 12 inches) or coloured throughout
more, if joint is unavoidable, crimped joint would be in the colour. The colour scheme shall be as
preferred. Spliced joint should not be used for large follows:
loads.
Conduit Type Colour scheme
There are different standard joints such as epoxy resin Power conduit Black
based joint, heat shrinkable plastic sleeve joint etc, and Security conduit Blue
each one has its advantage and disadvantage. Selection Fire alarm conduit Red
has to be made on the basis of application, site Low voltage conduit Brown
conditions and availability of skilled licensed UPS conduit Green
workmen. c) Cable trunkinglcable ways
6.6.4 Every joint in a cable shall be provided with For the smaller cables, enclosures such as
insulation not less effective than that of the cable cores conduit and trunking, may be employed and
and shall be protected against moisture and mechanical PVC-insulated, with or without sheath, single-
damage. Soldering fluxes which remain acidic or core cables installed following completion of
corrosive at the completion of the soldering operation the conduithrunking system. As these cables
shall not be used. are usually installed in relatively large groups,
care must be taken to avoid overheating and
For joints in paper-insulated metal-sheathed cables, a
to provide identification of the different
wiped metal sleeve or joint box, filled with insulating
circuits.
compound, shall be provided.
d) Tray and ladder rack
Where an aluminium conductor and a copper conductor As tray provides continuous support, unless
are joined together, precautions shall be taken against mounted on edge or in vertical runs (when
corrosion and mechanical damage to the conductors. adequate strapping or clipping is essential),
the mechanical strength of supported cable is
6.6.5 Pull at Joints and Terminals
not as important as with ladder-racking or
Every connection at a cable termination shall be structural support methods. Consequently,
made by means of a terminal, soldering socket, or tray is eminently suitable for the smaller
compression type socket and shall securely contain and unarmored cabling while racks and
anchor all the wires of the conductor, and shall not structural support, except for short lengths,
impose any appreciable mechanical strain on the call for armoured cables as they provide the
terminal or socket. necessary strength to avoid sagging between

30 NATIONALBUILDINGCODE OF INDIA
supports. Both tray and ladder racks can be soldered or welded or crimped lugs using suitable
provided with accessories to facilitate changes sleeve, lugs or ferrules unless the terminal is of such a
of route, and as PVC and similar insulating form that it is possible to securely clamp them without
materials are non-migratory (unlike the older the cutting away of cables stands. Cables in each circuit
types of impregnated cables) they provide no shall be bunched together.
difficulty in this respect on vertical runs.
6.8.3 All bare conductors shall be rigidly fixed in such
e) Insulated conductors while passing through
a manner that a clearance of at least 25 mm is
floors shall be protected from mechanical
maintained between conductors or opposite polarity
injury by means of rigid steel conduit, non- or phase and between the conductors and any material
metal conduit or mechanical protection to a other than insulation material.
height not less than 1.5 m above the floors
and flush with the ceiling below. This steel 6.8.4 If required, a pilot lamp shall be fixed and
conduit shall be earthed and securely bushed. connected through an independent single pole switch
Power outlets and wiring in the floor shall be and fuse to the bus-bars of the board.
generally avoided. If not avoidable, use false 6.8.5 In a hinged type board, the incoming and
floor or floor trunking. False floor shall be outgoing cables shall be fixed at one or more points
provided where density of equipment and according to the number of cables on the back of the
interconnection between different pieces of board leaving suitable space in between cables, and
equipment is high. Examples are: Mainframe shall also, if possible, be fixed at the corresponding
Computer station, Telecommunication switch points on the switchboard panel. The cables between
rooms, etc. these points shall be of such length as to allow the
Floor trunking shall be used in large halls, switchboard panel to swing through on angle of not
convention centres, open plan offices, less than 90°. The circuit breakers in such cases shall
laboratory, etc. be accessible without opening the door of distribution
In case of floor trunking drain points shall be board. Also, circuit breakers or any other equipment
provided, as there could be possibility of (having cable size more than 1.5 sq. mm multistrand
water seepage in the case of wiring passing wire) shall not be mounted on the door.
through the floors. Proper care should be NOTE — Use of hinged type boards is discouraged, as these
taken for suitable means of draining of water. boards lead to deterioration of the cables in the hinged portion,
Possibility of water entry exists from: (1) floor leading to failures or even fire.

washing, (2) condensation in some particular


6.8.6 Wires terminating and originating from the
weather and indoor temperature conditions.
protective devices shall be properly lugged and taped.
At the design stage, these aspects have to be
assessed and an appropriate means of 6.9 PVC-Sheathed Wiring System
avoiding, or reducing, and draining method
will have to be built in. 6.9.1 General

Floor oujlet boxes are generally provided for Wiring with Tough Rubber-Sheathed (TRS) cables had
the use of appliances, which require a signal, been the common system for low voltage installations.
or communication connection. The floor box Now TRS wiring is phased out as better and durable
and trunking system should cater to serve both insulating materials are available.
power distribution and the signal distribution,
Wiring with PVC-sheathed cables is suitable for
with appropriate safety and non-interference.
medium voltage” installation and may be installed
6.7.2 Where a wall tube passes outside a building so directly under exposed conditions of sun and rain or
as to be exposed to weather, the outer end shall be damp places.
bell-mouthed and turned downwards and properly
6.9.2 PVC ClampslPVC Channel
bushed on the open end.
Link clips had been the common system for wiring on
6.8 Wiring of Distribution Boards
wooden batten, which is now phased out. PVC clamps/
6.S.1 All connections between pieces of apparatus or PVC channel shall conform accepted standards. The
between apparatus and terminals on a board shall be clamps shall be used for temporary installations of 1-3
neatly arranged in a definite sequence, following the sheathed wires only. The clamps shall be fixed on wall
arrangements of the apparatus mounted thereon, at intervals of 100 mm in the case of horizontal runs
avoiding unnecessary crossings. and 150 mm in the case of vertical runs.

6.8.2 Cables shall be connected to a terminal only by PVC channel shall be used for temporary installations

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 31


in case more than 3 wires or wires or unsheathed wires. or distemper of suitable colour over a coat of oil-less
The channel shall be clamped on wall at intervals not primer, and the PVC-sheathed wiring shall be painted
exceeding 300 mm. with a synthetic enamel paint of quick drying type.

6.9.3 Protection of PVC-Sheathed Wiring from 6.10 Conduit Wiring System


Mechanical Damage
6.10.1 Surjace Conduit Wiring System with Rigid Steel
a) In cases where there are chances of any Conduits
damage to the wirings, such wirings shall be
covered with sheet metal protective covering, a) Type and size of conduit — All conduit pipes
the base of which is made flush with the shall conform to accepted standards [8-2(19)],
plaster or brickwork, as the case may be, or finished with galvanized or stove enamelled
the wiring shall be drawn through a conduit surface. All conduit accessories shall be of
complying with all requirements of conduit threaded type and under no circumstance pin
wiring system (see 6.10). grip type or clamp type accessories be used.
No steel conduit less than 16 mm in diameter
b) Such protective coverings shall in all cases
shall be used. The number of insulated
befitted on all down-drops within 1.5 m from
conductors that can be drawn into rigid
the floor.
conduit are given in Tables 1 and 2.
6.9.4 Bends in Wiring b) Bunching of cables — Unless otherwise
The wiring shall not in any circumstances be bent so specified, insulated conductors of ac supply
as to form a right angle but shall be rounded off at the and dc supply shall be bunched in separate
corners to a radius not less than six times the overall conduits. For lighting and smrdl power outlet
diameter of the cable. circuits phase egregation in separate conduits
is recommended.
6.9.5 Passing Through Floors
c) Conduit joints — Conduit pipes shall be
All cables taken through floors shall be enclosed in an joined by means of screwed couplers and
insulated heavy gauge steel conduit extending 1.5 m
screwed accessories only [see 8-2(19)]. In
above the floor and flush with the ceiling below, or by
long distance straight runs of conduit,
means of any other approved type of metallic covering.
inspection type couplers at reasonable
The ends of all conduits or pipes shall be neatly bushed intervals shall be provided or running threads
with porcelain, wood or other approved material. with couplers and jam-nuts (in the latter case
6.9.6 Passing Through Walls the bare threaded portion shall be treated with
anti-corrosive preservative) shall be provided.
The method to be adopted shall be according to good
Threaded on conduit pipes in all cases shall
practice. There shall be one or more conduits of
be between 11 mm to 27 mm long sufficient
adequate size to carry the conductors [see 6.10.l(a)].
to accommodate pipes to full threaded portion
The conduits shall be neatly arranged so that the cables
of couplers or accessories. Cut ends of conduit
enter them straight without bending.
pipes shall have no sharp edges nor any burrs
6.9.7 Stripping of Outer Covering left to avoid damage to the insulation of
conductors while pulling them through such
While cutting and stripping of the outer covering of
pipes.
the cables, care shall be taken that the sharp edge of
the cutting instrument does not touch the rubber or d) Protection against dampness — In order to
PVC-sheathed insulation of conductors. The protective minimize condensation or sweating inside the
tube, all outlets %f conduit system shall be
outer covering of the cables shall be stripped off near
connecting terminals, and this protective covering shall properly drained and ventilated, but in such a
manner as to prevent the entry of insects as
be maintained up to the close proximity of connecting
terminals as far as practicable. Care shall be taken to far as possible.
avoid hammering on link clips with any metal e) Protection of conduit against rust — The
instruments, after the cables are laid. Where junction outer surface of the conduit pipes, including
boxes are provided, they shall be made moisture-proof all bends, unions, tees, conduit system shall be
with an approved plastic compound. adequately protected against rust particularly
when such system is exposed to weather. In
6.9.8 Painting all cases, no bare threaded portion of conduit
If so required, the tough rubber-sheathed wiring shall, pipe shall be allowed unless such bare
after erection, be painted with one coat of oil-less paint threaded portion is treated with anti-corrosive

32 NATIONAL BUILDING CODE OF INDIA


Table 1 Maximum Permissible Number of Single-Core Cables up to and Including 1100 V that
can be Drawn into Rigid Steel and Rigid Non-Metallic Conduits
(Clauses 6.10.1 and 6.10.3.2)

Size of Cable Size of Conduit (mm)


T \
Nominal Cross Number and Dia 16 20 25 32 40 50 60
Sectional Area meter (in mm) (Number of Cables, Max)
mm2 of Wires f-----’--- c-–’——lr—+~~ ~~
SBSBSBS BSBSBSB
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16)
1.0 1/1.121) 547513102O 14 ——— ———
1.5 1/1.40 4375121020 14 ——— ———
2.5 1/1.80 320510818 12 ——— ———
3/1.061)
4 1/2.24 32437812 10 ——— ———
7/0.851)
6 1/2.80 2— 3265108— —————
7/1.061
10 7/1.401) — — 2— 436586— ———
16 711.70 — — — — 2— 4 ‘376————
25 7/2.24 — — — — — — 3254869 7
35 7/2.50 — — — — — — 2— 437586
50 19/1.80
NOTES
1 The table shows the maximum capacity of conduits for the simultaneously drawing of cables. The columns headed S apply to runs
of conduit which have distance not exceeding 4.25 m between draw-in boxes, and which do not deflect fmm the straight by an angle of
more than 15°. The coh.mmsheaded B apply to runs of conduit which deflect from the straight by an angle of more than 15°.
2 In case an inspection type draw-in box has been provided and if the cable if first drawn through one straight conduit, then through
the draw-in box, and then through the second straight conduit, such systems may be considered as that of a straight conduit even if the
conduit deflects through the straight by more than 15°.

‘) For copper conductors only.

Table 2 Maximum Permissible Number of Single-Core Cables that can be Drawn into
Cable Tunelling and Ducting System (Casing and Capping)
(Clauses 6.10.1 and 6.10.3.2)

Nominal Cross- 10/15 mm x 20 mm x 25 mm x 3ommx 4ommx 5ommx


Sectional Area of 10 mm 10 mm 10 mm 10 mm 20 mm 20 mm
Conductor in mm2
(1) (2) (3) (4) (5) (6) (7)
1.5 3 5 6 8 12 18
2.5 2 4 5 6 9 15
4 2 3 4 5 8 12
6 2 3 4 6 9
10 1 2 3 5 8
16 1 2 4 6
25 1 3 5
35 2 4
50 1 3
70 1 2

preservative or covered with suitable plastic of not more than 1 m, but on either side of
compound. couplers or bends or similar fittings, saddles
f) Fixing of conduit — Conduit pipes shall be shall be fixed at a distance of 300 cm from
fixed by heavy gauge saddles, secured to the centre of such fittings.
suitable wood plugs or other plugs with g) Bends in conduit — All necessary bends in
screws in an approved manner at an interval the system including diversion shall be done

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 33


by bending pipes; or by inserting suitable wall, ceiling, etc, at the time of their
solid or inspection type normal bends, elbows construction and shall be filled up neatly after
or similar fittings; or fixing cast iron, erection of conduit and brought to the original
thermoplastic or thermosetting plastic finish of the wall. In case of exposed bricld
material inspection boxes whichever is more rubble masonry work, special care shall be
suitable. Conduit fittings shall be avoided as taken to fix the conduit and accessories in
far as possible on conduit system exposed to position along with the building work.
weather; where necessary, solid type fittings b) Fixing ofconduit in chase —The conduit pipe
shall be used. Radius of such bends in conduit shall be fixed by means of staples or by means
pipes shall be not less than 7.5 cm. No length of saddles not more than 600 mm apart.
of conduit shall have more than the equivalent Fixing of standard bends or elbows shall be
of four quarter bends from outlet to outlet, avoided as far as practicable and all curves
the bends at the outlets not being counted. maintained by bending the conduit pipe itself
h) Outlets — All outlets for fittings, switches, with a long radius which will permit easy
etc, shall be boxes of suitable metal or any drawing-in of conductors. All threaded joints
other approved outlet boxes for either surface of rigid steel conduit shall be treated with
mounting system. preservative compound to secure protection
j) Conductors — All conductors used in conduit against rust.
wiring shall preferably be stranded. No single- c) Inspection boxes — Suitable inspection boxes
core cable of nominal cross-sectional area shall be provided to permit periodical
greater than 130 mmz enclosed along in a inspection and to facilitate removal of wires,
conduit and used for alternating current. if necessary. These shall be mounted flush
k) Erection and earthing of conduit — The with the wall. Suitable ventilating holes shall
conduit of each circuit or section shall be be provided in the inspection box covers. The
completed before conductors are drawn in. minimum sizes of inspection boxes shall be
The entire system of conduit after erection 75mmx75mm.
shall be tested for mechanical and electrical d) Types
.. of accessories to be used — All outlet,
continuity throughout and permanently such as switches and wall sockets, may be
connected to earth conforming to the either of flush mounting type or of surface
requirements as already specified by means mounting type.
of suitable earthing clamp efficiently fastened 1) Flush mounting type — All flush
to conduit pipe in a workman like manner for mounting outlets shall be of cast-iron
a perfect continuity between each wire and or mild steel boxes with a cover of
conduit. Gas or water pipes shall not be used insulating material or shall be a box made
as earth medium. If conduit pipes are liable of a suitable insulating material. The
to mechanical darnage they shall be adequately switches and other outlets shall be
protected. mounted on such boxes. The metal
m) Inspection type conduit fittings, such as box shall be efficiently earthed with
inspection boxes, draw boxes, bends, elbows conduit by a suitable means of earth
and tees shall be so installed that they can attachment.
remain accessible for such purposes as to 2) The switches/socket outlets shall
withdrawal of existing cables or the installing be adequately rated 1P for various
of traditional cables. utilizations.
6.10.2 Recessed Conduit Wiring System with Rigid 3) Surface modrtting type — If surface
Steel Conduit mounting type otulet box is specified, it
shall be of any suitable insulating
Recessed conduit wiring system shall comply with all
material and outlets mounted in an
the requirements for surface conduit wiring system
approved manner.
specified in 6.10.1 (a) to (k) and in addition, conform
to the requirements specified below: 6.10.3 Conduit Wiring System with RigidNon-Metallic
Conduits
a) Making of chase — The chase in the wall shall
be nearly made and be of ample dimensions Rigid non-metallic conduits are used for surface,
to permit the conduit to be fixed in the manner recessed and concealed conduit wiring. Cable trunking
desired. In the case of buildings under and ducting system of insulating material are used for
construction, chases shall be provided in the surface wiring.

34 NATIONAL BUILDING CODE OF INDIA


6.10.3.1 Type and size a) suitable for the extremes of ambient
temperature to which they are likely to be
All non-metallic conduits used shall conform to
subjected in service,
accepted standards [8-2( 19)]. The conduit may be
b) resistant to moisture and chemical
either threaded type or plain type in accordance with
atmospheres, and
accepted standards [8-2( 19)] and shall be used with
the corresponding accessories {see accepted standards c) resistant to low temperature and sunlight
[8-2(1 9)] }. The conduits shall be circular or rectangular effects.
cross-sections, For use underground, the material shall be resistant to
6.10.3.2 Bunching of cables moisture and corrosive agents.
NOTE — R&id PVC conduits are not suitable for use where
Conductors of ac supply and dc supply shall be
the normal working temperature of the conduits and fittings
bunched in separate conduits. For lighting and small may exceed 55”C. Certain types of rigid PVC conduits and
power outlet circuits phase segregation in separate their associated fittings are unsuitable for use where the ambient
circuits is recommended. The number of insulated temperature is likely to fan below -5”C.
cables that may be drawn into the conduits are given
6.10.4 Non-Metallic Recessed Conduit Wiring
in Table 1 and Table 2. In these tables the space factor
System
does not exceed 40 percent.
6.10.4.1 Recessed non-metallic conduit wiring system
6.10.3.3 Conduit joints
shall comply with all the requirements of surface non-
Conduits shall be joined by means of screwed or plain metallic conduit wiring system specified in 6.10.3.1
couplers depending on whether the conduits are to 6.10.3.9 except 6.10.3.4, In addition, the following
screwed or plain. Where there are long runs of straight requirements 6.10.4.2 to 6.10.4.5 also shall be
conduit, inspection type couplers shall be provided at complied with.
intervals. For conduit fittings and accessories reference
may be made to the good practice [8-2(19)]. 6.10.4.2 Fixing of conduit in chase

6.10.3.4 Fixing of conduits The conduit pipe shall be fixed by means of stapples
or by means of non-metallic saddles placed at not more
The provisions of 6.10.l(f) shall apply except that the than 80 cm apart or by any other approved means of
spacing between saddles or supports is recommended fixing. Fixing of standard bends or elbows shall be
to be 600 cm for rigid non-metallic conduits. avoided as far as practicable and all curves shall be
6.10.3.5 Bends in conduits maintained by sending the conduit pipe itself with a
long radius which will permit easy drawing in of
Wherever necessary, bends or diversions may be conductors. At either side of bends, saddles/stapples
achieved by bending the conduits (see 6.10.3.8) or by shall be fixed at a distance of 15 cm from the centre of
employing normal bends, inspection bends, inspection bends.
boxes, elbows or similar fittings.
6.10.4.3 Inspection boxes
6.10.3.6 Conduit fittings shall be avoided, as far as
possible, on outdoor systems. Suitable inspection boxes to the nearest minimum
requirements shall be provided to permit periodical
6.10.3.7 Outlets inspection and to facilitate replacement of wires, if
In order to minimize condensation or sweating inside necessary. The inspection/junction boxes shall be
the conduit, all outlets of conduit system shall be mounted flush with the wall or ceiling concrete. Where
properly drained and ventilated, but in such a manner necessary deeper boxes of suitable dimensions shall
as to prevent the entry of insects. be used. Suitable ventilating holes shall be provided
in the inspection box covers, where required.
6.10.3.8 Heat may be used to soften the conduit for
bending and forming joints in case of plain conduits. 6.10.4.4 The outlet boxes such as switch boxes,
As the material softens when heated, sitting of conduit regulator boxes and their phenolic laminated sheet
in close proximity to hot surfaces should be avoided. covers shall be as per requirements of 6.10.1 (h).
Caution should be exercised in the use of this conduit They shall be mounted flush with the wall.
in locations where the ambient temperature is 500C
or above. Use of such conduits in places where 6.10.4.5 Types of accessories to be used
ambient temperature is 60”C or above is prohibited. All outlets such as switches, wall sockets, etc, may
6.10.3.9 Non-metallic conduit systems shall be used be either flush mounting type or of surface mounting
only where it is ensured that they are: type.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 35


7 FITTINGS AND ACCESSORIES NOTE — A recommended schedule of socket-outlets in a
residential building is given below:
7.1 Ceiling Roses and Similar Attachments
Location Number of 5A Numberof 15A
7.1.1 A ceiling rose or any other similar attachment Socket-Outlets Socket-Outlets
shall not be used on a circuit the voltage of which Bed room 2t03 1
normally exceeds 250 V. Living room 2t03 2
Kitchen 1 2
7.1.2 Normally, only one flexible cord shall be Dining room 2 1
attached to a ceiling rose. Specially designed ceiling Garage 1 1
roses shall be used for multiple pendants. For refrigerator 1
For air conditioner — (one for each)
7.1.3 A ceiling rose shall not embody fuse terminal VERANDAH 1 per 10 mz 1
as art integral part of it. Bathroom 1 1

7.2 Socket-Outlets and Plugs 7.3 Lighting Fittings


Each 16A socket-outlet provided in buildings for the 7.3.1 A switch shall be provided for control of every
use of domestic appliances such as air conditioner, lighting fitting or a group of lighting fittings. Where
water cooler, etc, shall be provided with its own control at more than one point is necessary as many
individual fuse, with suitable discrimination with back- two way or intermediate switches maybe provided as
up fuse or miniature circuit-breaker provided in the there are control points.
distribution/sub-distribution board. The socket-outlet
shall not necessarily embody the fuse as an integral
7.3.2 In industrial premises lighting fittings shall be
supported by suitable pipe/conduits, brackets fabricated
part of it.
from structural steel, steel chains or similar materials
7.2.1 Each socket-outlet shall also be controlled by a depending upon the type and weight of the fittings.
switch which shall preferably be located immediately Where a lighting fitting is supported by one or more
adjacent thereto or combined therewith. flexible cords, the maximum weight to which the twin
7.2.2 The switch controlling the socket-outlet shall be flexible cords may be subjected shall be as follows:
on the live side of the line.
Nominal Cross-Sectional Maximum
7.2.3 Ordinary socket-outlet may be fixed at any Area of Twin Cord Permissible Weight
convenient place at a height above 20 cm from the -2
kg
floor level and shall be away from danger of 0.5 2
mechanical injury. 3
0.75
NOTE — In situations where a socket-outlet is accessible to 1.0 5
children, it is necessary to install an interlocked plug and socket 1.5 5.3
or alternatively a socket-outlet which automatically gets
2.5 8.8
screened by the withdrawal of plug. In industrial premises
socket-outlet of rating 20 A and above shall preferably be 4 14.0
provided with interlocked type switch.

7.2.4 In an earthed system of supply, a socket-outlet 7.3.3 No flammable shade shall forma part of lighting
with plug shall be of three-pin type with the third fittings unless such shade is well protected against all
terminal connected, to the earth. When such socket- risks of fire. Celluloid shade or lighting fittings shall
outlets with plugs are connected to any current not be used under any circumstances.
consuming device of metal or any non-insulating 7.3.4 General and safety requirements for electrical
material or both, conductors connecting such cttrrent- lighting fittings shall Be in accordance with good
consuming devices shall be of flexible cord with an practice [8-2(20)].
earthing core and the earthing core shall be secured by
connecting between the earth terminal of plug and the 7.3.5 The lighting fittings shall conform to accepted
body of current-consuming devices. standards [8-2(10)].

In industrial premises three-phase and neutral socket- 7.4 Fitting-Wire


outlets shall be provided with a earth terminal either
The use of fittings-wire shall be restricted to the internal
of pin type or scrapping type in addition to the main
wiring of the lighting fittings. Where fittings-wire is
pins required for the purpose.
used for wiring fittings, the sub-circuit loads shall
7.2.5 In wiring installations, metal clad switch, socket- terminate in a ceiling rose or box with connectors from
outlet and plugs shall be used for power wiring. which they shall be carried into the fittings.

36 NATIONAL BUILDING CODE OF JNDL4


7.5 Lampholders its own regulator as well as a switch in
series.
Lampholders for use on brackets and the like shall be
in accordance with accepted standards [8-2(21)] and b) All ceiling fans shall be wired with normal
wiring to ceiling roses or to special connector
all those for use with flexible pendants shall be
boxes to which fan rod wires shall be
provided with cord grips. All lampholders shall be
provided with shade carriers. Where centre-contact connected and suspended from hooks or
Edison screw Iampholders are used, the outer or screw shackels with insulators between hooks and
suspension rods. There shall be no joint in the
contacts shall reconnected to the ‘middle wire’, the
suspension rod, but if joints are unavoidable
neutral, the earthed conductor of the circuit.
then such joints shall be screwed to special
7.6 Outdoor Lamps couplers of 5 cm minimum length and both
ends of the pipes shall touch together within
External and road lamps shall have weatherproof
the couplers, and shall in addition be secured
fittings of approved design so as to effectively prevent
by means of split pins; alternatively, the two
the ingress of moisture and dust. Flexible cord and cord
pipes may be welded. The suspension rod
grip lampholders shall not be used where exposed to
shall be of adequate strength to withstand the
weather. In VERANDAHS and similar exposed
dead and impact forces imposed on it.
situations where pendants are used, these shall be of
Suspension rods should preferably be
fixed rod type.
procured along with the fan.
7.7 Lamps c) Fan clamps shall be of suitable design
according to the nature of construction of
All lamps unless otherwise required and suitably ceiling on which these clamps are to be fitted.
protected, shall be hung at a height of not less than In all cases fan clamps shall be fabricated from
2.5 m above the floor level. All electric lamps and new metal of suitable sizes and they shall be
accessories shall conform to accepted standards as close fitting as possible. Fan clamps for
[8-2(22)]. reinforced concrete roofs shall be buried with
a) Portable lamps shall be wired with flexible the casting and due care shall be taken that
cord. Hand lamps shall be equipped with a they shall serve the purpose. Fan clamps for
handle of moulded composition or other wooden beams, shall be of suitable flat iron
material approved for the purpose. Hand fixed on two sides of the beam and according
lamps shall be equipped with a substantial to the size and section of the beam one or two
guard attached to the lampholder or handle. mild steel bolts passing through the beam shall
Metallic guards shall be earthed suitably. hold both flat irons together. Fan clamps for
steel joist shall be fabricated from flat iron to
b) A bushing or the equivalent shall be provided
fit rigidly to the bottom flange of the beam.
where flexible cord enters the base or stem of
Care shall be taken during fabrication that the
portable lamp. The bushing shall be of
metal does not crack while hammer to shape.
insulating material unless a jacketted type of
Other fan clamps shall be made to suit the
cord is used.
position, but in all cases care shall be taken
c) All wiring shall be free from short-circuits and to see that they are rigid and safe.
shall be tested for these defects prior to being
d) Canopies on top and bottom of suspension
connected to the circuit.
rods shall effectively conceal suspensions and
d) Exposed live parts within porcelain fixtures connections to fan motors, respectively.
shall be suitably recessed and so located as to
e) The lead-in-wire slytll be of nominal cross-
make it improbable that wires will come in
sectional area not less than 1.5 mmz copper
contact with them. There shall be a spacing
and shall be protected from abrasion.
of at least 125 mm between live parts and the
f) Unless otherwise specified, the clearance
mounting plane of the fixture.
between the bottom most point of the ceiling
7.8 Fans, Regulators and Clamps fan and the floor shall be not less than 2.4 m.
The minimum clearance between the ceiling
7.8.1 Ceiling Fans
and the plane of the blades shall be not less
Ceiling fans including their suspension shall conform than 300 mm.
to accepted standards [8-2(23)] and to the following
A Typical arrangement of a fan clamp is given in Fig. 2.
requirements:
NOTE — All fan clamps shatl be so fabricated that fans revolve
a) Control of a ceiling fan shall be through steadily.

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 37


I---—-’’”----t--” —-7----’”-----7
●
w
● .’ A“
. ,1 25 min.
4a’”~* ,. , “* ‘. . ‘“ *
‘%3‘ 160
●
4, 31
4 II
4
● .” 160
●
12
I
*

EXPOSED LOOP
SHALLBE PAINTED SHACKLE

m
4
‘4 w
4 4“
A 25 min.
70
●

CT7iii3 31
‘4
● 6

* 70
..” T

/ CEILING

/’
i’ /’ RCC BEAM

L - EXPOSED Loop

SHALLBE PAINTED

2B SLAB WITH BEAM

All dimensions in millimetres.


NOTES
1 RCC slab steel reinforcement not shown.
2 Fan clamp shall be placed in position such that its projecting arms in the line of length of beam.

FIG. 2 TYPICAL DESIGN OF FAN CLAMPS

7.8.2 Exhaust Fans 7.9 Attachment of Fittings and Accessories

For fixing of an exhaust fan, a circular hole shall be 7.9.1 In wiring other than conduit wiring, all ceiling
provided in the wall to suit the size of the frame which roses, brackets, pendants and accessories attached to
shall be fixed by means of rag-bolts embedded in the walls or ceilings shall be mounted on substantial teak
wall. The hole shall be neartly plastered with cement wood blocks twice varnished after all fixing holes are
and brought to the original finish of the wall. The made in them. Blocks shall not be less than 4 cm deep.
exhaust fan shall be connected to exhaust fan point Brass screws shall only be used for attaching fittings
and accessories to their base blocks.
which shall be wired as near to the hole as possible by
means of a flexible cord, care being taken that the 7.9.2 Where teak or hardwood boards are used for
blades rotate in the proper direction. mounting switches, regulators, etc, these boards shall

38 NATIONAL BUILDING CODE OF INDIA


be well varnished with pure shellac on all four sides Life Safety’. Exhaust fan requirement comes for catering to
(both inside and outside), irrespective of being painted smoke extraction atso. Basement areas depend on the system
of fresh air fans and exhaust fans.
to match the surroundings. The size of such boards
shall depend on the number of accessories that could 7.12.5 Positioning of fans and light fittings shall be
conveniently and neatly be arranged. Where there is chosen to make these effective without causing
danger of attack by white ants, the boards shall be shadows and stroboscopic effect on the working planes.
treated with suitable anti-termite compount and painted
on both sides. 8 EARTHING

8.1 General
7.10 Interchangeability
Earthing shall generally be carried out in accordance
Similar part of all switches, larnpholders, distribution
with the requirements of Indian Electricity Rules, 1956
fuse-boards, ceiling roses, brackets, pendants, fans and
as amended time to time and the relevant regulations
all other fittings shall be so chosen that they are of the
of the Electricity Supply Authority concerned.
same type and interchangeable in each installation.
The main earthing system of an electrical installation
7.11 Equipment
must consist of
Electrical equipment which form integral part of wiring
a) An earth electrode;
intended for switching or control or protection of
wiring installations shall conform to the relevant Indian b) A main earthing wire;
Standards wherever they exist. c) An earth bar (located on the main switchboard)
for the connection of the main earthing wire,
7.12 Fannage protective earthing wires and/or bonding
7.12.1 Where ceiling fans are provided, the bay sizes wires within the installation; and
of a building, which control fan point locations, play d) A removable lirdGwhich effectively disconnects
an important part. the neutral bar from the earth b&.

7.12.2 Fans normally cover an area of 9 m2 to 10 m2 NOTE— The requirementsof (c) and (d) above must
be carried out by the licensed electricianas part of the
and therefore in general purpose office buildings, for
switchboardinstallation.
every part of a bay to be served by the ceiling fans, it
is necessary that the bays shall be so designed that full The main earthing wire termination must be readily
number of fans could be suitably located for the bay, accessible at the earth electrode.
otherwise it will result in ill-ventilated pockets. In
The main earthing wire connection must:
general, fans in long halls may be spaced at 3 m in
both the directions. If building modules do not lend a) be mechanically and electrically sound;
themselves for proper positioning of the required b) be protected against damage, corrosion, and
number of ceiling fans, such as air circulators or bracket vibration;
fans would have to be employed for the areas c) not place any strain on the various parts of
uncovered by the ceiling fans. For this, suitable the connection;
electrical outlets shall be provided although result will
d) not damage the wire or fittings; and
be disproportionate to cost on account of fans.
e) be secured at the earth electrode
7.12.3 Proper air circulation could be achieved either
by larger number of smaller fans or smaller number of Use a permanent fitting (like a screwed-down plastic
larger fans. The economics of the system as a whole label or copper label, or one that can be threaded onto
should be a guiding factor in choosing the number and the cable) at the connection po@ that is clearly marked
type of fans and their locations. with the words: “EARTHING LEAD — DO NOT
DISCONNECT” or “EARTHING CONDUCTOR —
7.12.4 Exhaust fans are necessary for spaces, such as DO NOT DISCONNECT”.
community toilets, kitchens and canteens, and godowns
to provide the required number of air changes (see 8.1.1 All medium voltage equipment shall be earthed
Part 8 ‘Building Services, Section 1 Lighting and by two separate and distinct comections with earth.
Ventilation’). Since the exhaust fans are located The contact area of earth conductor/plate shall be
generally on the outer walls of a room appropriate determined using guidelines specified in IS 3043.
openings in such walls shall be provided for in the Medium voltage systems of 400/230 V, 4-wire,
planning stage. 3-phase, systems are normally operated with the neutral
NOTE— Exhaustfanrequirementis basedon therecommended solidly earthed at source. At medium voltage, Indian
air changes.Reference may also be made to Part 4 ‘Fire and Electricity Regulations require that the neutral be

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 39


earthed by two separate and distinct connections with animals and of property and it is generally known as
earth. Source in the case of a substation (such as 1lkV/ equipment earthing.
400 V) would be the neutrrd(s) of the transformer(s).
8.2 Earth Electrodes
Neutral conductor of half the size of the phase
conductor was permitted in earlier installations. But Earth electrode either in the form of pipe electrode or
with the proliferation of equipment using non-linear plate electrode should be provided at all premises for
devices and consequent increase in harmonics, the providing an earth system. Details of typical pipe and
neutral will carry a current more than the notional out- plate earth electrodes are given in Fig. 3 and Fig. 4.
of-balance current and as such neutral conductor shall
Although electrode material does not affect initial earth
be of the same size as the phase conductor.
resistance, care should be taken to select a material
In the case of high and extra high voltages, the neutral which is resistant to corrosion in the type of soil in
points shall be earthed by not Iess than two separate which it is used. Under ordinary conditions of soil,
and distinct connections with earth, each having use of copper, iron or mild steel electrodes is
its own electrode at the generating station or recommended. In case where soil condition leads to
substation and may be earthed at any other point excessive corrosion of the electrode, and the
provided no interference is caused by such earthing. connections, it is recommended to use either copper
The neutral may be earthed through suitable electrode or copper clad electrode or zinc coastal
impedance. Neutral earthing conductor shall be sized galvanized iron electrode. The electrode shall be kept
at to have a current carrying capacity not less than free from paint, enamel and grease. It is recommended
the phase current. to use similar material for earth electrodes and earth
conductors or othetiise precautions should be taken
8.1.2 As far as possible, all earth connections shall be
to avoid corrosion.
visible for inspection.
8.3 As far as possible, all earth connections shall be
8.1.3 Earth earth system shall be so devised that the
visible for inspection and shall be carefully made; if
testing of individual earth electrode is possible. It is
they are poorly made or inadequate for the purpose
recommended that the value of any earth system
for which they are intended, loss of life and property
resistance shall be such as to conform with the degree
or serious personal injury may result.
of shock protection desired.
To obtain low overall resistance the current density
8.1.4 It is recommended that a drawing showing the
should be as low as possible in the medium adjacent
main earth connection and earth electrodes be prepared
to the electrodes; which should be so designed as to
for each installation.
cause the current density to decrease rapidly with
8.1.5 No addition to the current-carrying system, either distance from the electrode. This requirement is met
temporary or permanent, shall be made which will by making the dimensions in one direction large
increase the maximum available earth fault current or compared with those in the other two, thus a pipe, rod
its duration until it has been ascertained that the existing or strip has a much lower resistance than a plate of
arrangement of earth electrodes, earth busbar, etc, are equal surface area. The resistance is not, however,
capable of carrying the new value of earth fault current inversely proportional to the surface area of the
which may be obtained by this addition. electrode.

8.1.6 No cut-out, link or switch other than a linked 8.4 Equipment and Portions of Installations which
switch arranged to operate simultaneously on the shall be Earthed
earthed or earthed neutral conductor and the live
8.4.1 Equipment to be Earthed
conductors, shall be inserted on any supply system.
This, however, does not include the case of a switch Except for equipment provided with double insulation,
for use in controlling a generator or a transformer or a all the non-current carrying metal parts of electrical
link for test purposes. installations are to be earthed properly. All metal
conduits, trunking, cable sheaths, switchgear,
8.1.7 All materials, fittings, etc, used in earthing shall
distribution fuseboards, lighting fittings and all other
conform to Indian Standard specifications, wherever
parts made of metal shall be bended together and
these exist.
connected by means of two separate and distinct
8.1.8 Earthing associated with current-carrying conductors to an efficient earth electrode.
conductor is normally essential for the security of the
8.4.2 Structural Metal Work
system and is generally known as system earthing,
while earthing of non-current carrying metal work and Earthing of the metallic parts shall not be effected
conductor is essential for the safety of human life, of through any structural metal work which houses the

40 NATIONALBUILDING CODE OF INDIA


Cl COVER HINGED
TO Cl FRAME

-125- “ 400

4’ GL

; ‘$ ‘“..
. . \
w

065 PVC
CONDUIT
EMBEDDED
. < ““ “
‘4...4’; ~.. 1 I

●
. ,
. .
“’f. ””q : ..4’”.””.””.

P
.
.
. ;0
.

L- 250 ‘-
I‘ -d 250

Cl PIPE 100 ID
13 mm THICK

p150 i 150~
k
A HOMOGENEOUS LAYER
OF COKE/CHARCOAL, SALT
AND SAND

/-0 10 BOLTS
)0

J *.
AND NUTS
75 50~25
v
~* ~4
+’- 4.
.

..*,

● . .= ..$. ● -.
.“.. .q. . ‘ .0 . . .. .
/...

. ...&

.:

. .
, ●“

T ~50 x 3 :: . ...*
4, . . . .

GI STRIP .

DETAIL A

All dimensions in millimetres.

FIG. 3 TYPICALARRANGEMENT
OFPIPEEARTHING

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 41


42 NATIONAL BUILDING CODE OF INDIA
installation. Where metallic parts of the installation are c) IT System — A system which has source
not required to be earthed and are liable to become either unearthed or earthed through a high
alive should the insulations of conductors become impedance and the exposed conductive
defective, such metallic parts shall be separated by parts of the installations are connected to
durable non-conducting material from any structural electrically independent earth electrodes.
work.
9 INSPECTION AND TESTING OF
8.5 Neutral Earthing INSTALLATION
To comply with Rule 32(1) of Indian Electrici@ Rules 9.1 General Requirements
1956, no fuses or circuit breakers other than a linked
circuit breaker shall inserted in an earthed neutral 9.1.1 Before the completed installation, or an addition
to the existing installation, is put into service,
conductor, a linked switch or linked circuit breaker
shall be arranged to break or the neutral either with or inspection and testing shall be carried out in accordance
with the Indian Electricity Rules, 1956. In the event of
after breaking all the related phase conductors and.
defects being found, these shrdl be rectified, as soon
shall positively make (or close) the neutral before
making (or closing) the phases. as practicable and the installation retested.

If this neutral point of the supply system is connected 9.1.2 Periodic inspection and testing shall be carried
permanently to earth, then the above rule applies out in order to maintain the installation in a sound
condition after putting into service.
throughout the installation including 2-wire final
circuits. This means that no fuses may be inserted in 9.1.3 Where an addition is to be made to the fixed
the neutral or common return wire. And the neutral wiring of an existing installation, the latter shall be .-.
should consist of a bolted solid link, or part of a linked examined for compliance with the recommendations
switch, which completely disconnects the whole of the Code.
system from the supply. This linked switch must be
arranged so that the neutral makes before, and break 9.1.4 The individual equipment and materials which
after the phases. form part of the installation shall generrdly conform to
the relevant Indian Standard Specification wherever
8.6 System of Earthing applicable. If there is no relevant Indian Standard
Equipment and portions of installations shall be Specification for any item, these shall be approved by
deemed to be earthed only if earthed in accordance the appropriate authority.
with either the direct earthing system, the multiple 9.L5 Completion Drawings
earthed neutral system or the earth leakage circuit-
breaker system. In all cases, the relevant provisions of On completion of the electric work, a wiring diagram
Rules 33 and61 of the Indian Electricity Rules, 1956 shall be prepared and submitted to the engineer-in-
charge or the owner. All wiring diagrams shall indicate
(see Annex B) shall be complied with.
clearly, the main switch board, the runs of various
The earthing of electrical installations for non- mains and submains and the position of all points and
industrial and industrial buildings shall be done in their controls. All circuits shall be clearly indicated
accordance with good practice [8-2(24)]. and numbered in the wiring diagram and all points shall
be given the same number as the circuit in which they
8.7 Classification of Earthing System
are electrically connected. Also the location and
The earthing systems are classified as follows: number of earth points and the run of each loads should
be clearly shown in the completion drawings.
a) TN System — A system which has one or more
points of the source of energy directly earth, 9.2 Inspection of the Installation
and the exposed and extraneous conductive
parts of the installation are connected by means 9.2.1 General
of protective conductors to the earth points of On completion of wiring a general inspection shall be
the source, that is, currents to flow from the carried out by competent personnel in order to verify
installation to the earth points of the source. that the provisions of this Code and that of Indian
b) TTSystem — A system which has one or more Electricity Rules, 1956, have been complied with. This,
points of the source of energy directly earth, among other things, shall include checking whether
and the exposed and extraneous conductive all equipments, fittings, accessories, wirdcables, used
parts of the installation are connected to a in the installation are of adequate rating and quality to
local earth electrodes or electrodes electrically meet the requirement of the load. General workmanship
independent of the source earth. of the electrical wiring with regard to the layout and

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 43


finish shall be examined for neatness that would 17) The earth bus bars have tight connections and
facilitate easy identification of circuits of the system, corrosion-free joint surfaces;
adequacy of clearances, soundness, contact pressure 18) Operating handle of protective device are
and contact area. A complete check shall also be made provided at an accessible height from ground;
of all the protective devices, with respect to their 19) Adequate headroom is available in the
ratings, range of settings and co-ordination between transformer room for easy topping-up of oil,
the various protective devices. maintenance, etc;
9.2.2 Item to be Inspected 20) Safety devices, horizontal and vertical
barriers, bus bar covers/shrouds, automatic
9.2.2.1 Substation installations
safety shutters/doors interlock, handle
In substation installation, it shall be checked whether: interlock are safe and in reliable operation in
all panels and cubicles;
1) The installation has been carried out in
accordance with the approved drawings; 21) Clearances in the front, rear and sides of the
main HV and MV and sub-switch boards are
2) Phase-to-phase and phase to earth clearances
adequate;
are provided as required;
22) The switches operate freely; the 3 blades make
3) All equipments are efficiently earthed and
contact at the same time, the arcing horns
properly connected to the required number
contact in advance; and the handles are
of earth electrodes;
provided with locking arrangements;
4) The required ground clearance to live-
23) Insulators are free from cracks, and are clean;
terminals is provided; ----
24) In transformers, there is any oil lek,
5) Suitable fencing is provided with gate with
lockable arrangements; 25) Connections to bushing in transformers for
tightness and good contact;
6) The required number of caution boards fire-
fighting equipments, operating rods, rubber 26) Bushings are free from cracks and are clean;
mats, etc, are kept in the substation; 27) Accessories of transformers like breathers,
7) In case of indoor substation sufficient vent pipe, Buchholz relay, etc, are in order;
ventilation and draining arrangements are 28) Connections to gas relay in transformers are
made; in order;
8) All cable trenches are provided with non- 29) Oil and winding temperature are set for
inflammable covers; specific requirements in transformers;
9) Free accessibility is provided for all equipments 30) In case of cable cellars, adequate arrangements
for normal operation; to pump out water that has entered due to
10) All name plates are fixed and the equipments seepage or other reasons;
are fully painted; 31) All incoming and outgoing circuits of HV and
11) All construction materials and temporary MV panels are clearly and indelibly labelled
for identifications;
connections are removed;
12) Oil-level, busbar tightness, transformer tap 32) No cable is damaged;
position, etc, are in orde~ 33) There is adequate clearance around the
13) equipments installed; and
Earth pipe troughs and cover slabs are
provided for earth electrodes/earth pits and 34) Cable terminations are proper.
the neutral and LA earth pits are marked for 9.2.2.2 Medium voltage installation
easy identification;
In medium voltage installations, it shall be checked
14) Earth electrodes are of GI pipes or CI pipes
or copperplates. For earth connections, brass whethe~
bolts and nuts with lead washers are provided 1) All blocking materials that are used for safe
in the pipes/plates; transportation in switchgears, contractors,
15) Earth pipe troughs and oil sumps/pits are free relays, etc, are removed;
from rubbish and dirt and stone jelly and the 2) All connections to be earthing system are
earth connections are visible and easily feasible for periodical inspection;
accessible; 3) Sharp cable bends are avoided and cables are
16) HT and LT panels are switchgears are all taken in a smooth manner in the trenches or
vermin and damp-proof and all unused alongside the walls and ceilings using suitable
openings or holes are blocked properly; support clamps at regular intervals;

44 NATIONAL,BUILDINGCODE OF INDIA
4) Suitable linked switch or circuit breaker or 2) The types and size of supports are suitable
lockable pushbutton is provided near the for the overhead lines/conductors used and
motors/apparatus for controlling supply to the are in accordance with approved drawing and
motor/apparatus in an easily accessible standards;
location; 3) Clearances from ground level to the lowest
5) Two separate and distinct earth connections conductor of overhead lines, sag conditions,
are provided for the motor/apparatus; etc, are in accordance with the relevant
6) Control switch-fuse is provided at an accessible standard;
height from ground for controlling supply to 4) Where overhead lines cross the roads or cross
overhead traveling crane, hoists, overhead each other or are in proximity with one
bus bar trunking; another, suitable guarding is provided at road
7) The metal rails on which the crane travels are crossings and also to protect against
electrically continuous and earthed and possibility of the lines coming in contact with
bonding of rails and earthing at both ends are one anotheu
done; 5) Every guard wire is properly earthed;
8) Four core cables are used for overhead 6) The type, size and suitability of the guarding
traveling crane and portable equipments, the arrangement provided is adequate;
fourth core being used for earthing, and 7) Stays are provided suitably on the over-head
separate supply for lighting circuit is taken; lines as required and are efficiently earthed
9) If flexible metallic hose is used for wiring to or provided with suitably stay insulators of
motors and other equipment, the wiring is suitable voltages;
enclosed to the full lengths, and the hose 8) Anti-climbing devices and Danger Board/
secured properly by approved means; Caution Board Notices are provided on all HT
10) The cables are not taken through areas where supports ;
they are likely to be damaged or chemically 9) Clearances along the route are checked and
affected; all obstructions such as trees/branches and
11) The screens and arrnours of the cables are shrubs are cleared on the route to the required
earthed properly; distance on either side;
12) The belts of the belt driven equipments are 10) Clearance between the live conductor and the
properly guarded; earthed metal parts are adequate;
13) Adequate precautions are taken to ensure that 11) For the service connections tapped-off from
no live parts are so exposed as to cause dangev the overhead lines, cut-outs of adequate
14) Ammeters and voltmeters are tested; capacity are provided,
15) The relays are inspected visually by moving 12) All insulators are properly and securely
covers for deposits of dusts or other foreign mounted, also they are not damaged.
matter, 13) All poles are properly grouted/insulated so
16) Wherever bus ductsh-ising mainsloverhead as to avoid bending of pole towards tension;
bus trucking are used, special care should be and
taken for earthing the system. All tap off 14) Steel poles, if used shall be properly earthed.
points shall be provided with adequately rated
9.2.2.4 Lighting circuits
protective device like MCB, MCCB, fuses,
ELCB, RCCB, etc; The lighting circuits shall be checked whethe~
17) All equipments shall be weather, dust and
1) Wooden boxes and panels are avoided in
vermin proofi and
factories for mounting the lighting boards and
18) Any and all equipments having air insulation switch controls, etc;
as media shall maintain proper distances 2) Neutral links are provided in double pole
between phases; phase to neutral; phase to switch-fuses which are used for lighting
earth and earth to neutral. control, and no protective devices (such as
9.2.2.3 Overhead lines MCB, MCCB, fuses, ELCB, etc) is provided
in the neutral;
For overhead lines it shall be checked whether:
3) The plug points in the lighting circuit are all
1) All conductors and apparatus including live of 3-pin type, the third pin being suitably
parts thereof are inaccessible; earthed;

PART 8 BUILDINGSERVICES — SECTION 2 ELECTRICAL ANDALLlED INSTALLATIONS 45


4) Tamper-proof interlocked switch socket and shall commence after obtaining permit to work from
plug are used for locations easily accessible; the engineer-in-charge and after ensuring the safety
5) Lighting wiring in factory area is taken provisions.
enclosed in conduit and conduit properly 9.3.2 Testing
earthed, or alternatively, armoured cable “*
wiring is used; 9.3.2.1 Switchboards .
6) A separate earth wire is run in the lighting HV and MV switchboards shall be tested in the manner
installation to provide earthing for plug points, indicated below:
fixtures and equipments;
a) All high voltage switchboards shall be tested
7) Proper connectors and junction boxes are used for dielectric test as per good practice [8-
wherever joints are to be made in conductors 2(25)].
or cross over of conductors takes place;
b) All earth connections shall be checked for
8) Cartridge fuse units are fitted with cartridge continuity.
fuses only;
c) The operation of the protective devices shall
9) Clear and permanent identification marks be tested by means of secondary or primary
are painted in all distribution boards, injection tests.
switchboards, sub-main boards and switches
d) The operation of the breakers shall be tested
as necessary;
from all control stations.
10) The polarity having been checked and all
e) Indication/signalling lamps shall be checked
protective devices (such as MCB, MCCB,
for proper working.
fuses, ELCB, etc) and single pole switches
f) The operation of the breakers shrdl be tested
are connected on the phase conductor only
for all interlocks.
and wiring is correctly connected to socket-
outlets; g) The closing and opening timings of the
breakers shall be tested wherever required for
11) Spare knockouts provided in distribution
auto-transfer schemes.
boards and switch fuses are blocked;
h) Contact resistance of main and isolator
12) The ends of conduits enclosing the wiring
contacts shall be measured.
leads are provided with ebonite or other
suitable bushes; j) The specific gravity and the voltage of the
control battery shall be measured.
13) The fittings and fixtures used for outdoor use
are all of weather-proof construction, and 9.3.2.2 Transformers
similarly, fixtures, fittings and switchgears
Transformers are tested in the manner indicated below:
used in the hazardous area, are of flame-proof
application; a) All commissioning tests shall be in accordance
14) Proper terminal connectors are used for with good practice [8-2(26)].
termination of wires (conductors and earth b) Insulation resistance on HV and MV windings
leads) and all strands are inserted in the shall be measured at the end of 1 min as also
terminals; at the end of 10 min of measuring the
15) Flat ended screws are used for fixing polarization index. The absolute value of
conductor to the accessories; insulation resistance should not be the sole
criterion for determining the state of dryness
16) Use of flat washers backed up by spring
of the insulation. Polarization index values
washers for making end connections is
should form the b~ for determining the state
desimble; and
of dryness of insulation. For any class of
17) All metallic parts of installation such as
insulation, the polarization index should be
conduits, distribution boards, metal boxes, etc
greater than 1.5.
have been properly earthed.
9.3.2.3 Cables
9.3 Testing of Installation
Cable installations shall be checked as below:
9.3.1 General
a) It shall be ensured that the cables conform to
After inspection, the following tests shall be carried the relevant Indian Standards. Tests shrdl rdso
out, before an installation or an addition to the existing be done in accordance with good practice
installation is put into service. Any testing of the [8-2(6)]. The insulation resistance before and
electrical installation in an already existing installation after the tests shall be checked.

46 NATIONALBUILDINGCODE OF INDIA
b) The insulation resistance between each and except in earthed concentric wiring, all
conductor and against earth shall be lamps in position or both poles of installation
measured. The insulation resistance varies otherwise electrically connected together, a
with the type of insulation used and with the dc voltage of not less than twice the working
length of cable. The following empirical rule voltage, provided that it does not exceed
gives reasonable guidance: 500 V for medium voltage circuits. Where the
supply is derived from three-wire (ac or dc)
Insulation resistance in megaohms
or a poly-phase system, the neutral pole of
10x Voltage in kV which is connected to earth either direct or
= through added resistance the working voltage
Length in km
shw be deemed to be that which is maintained
c) Physical examination of cables shall be between the outer or phase conductor and the
carried out. neutral.
d) Cable terminations shall be checked. b) The insulation resistance in megaohms of an
e) Continuity test shall be performed before installation measured as in (a) shall be not less
charging the cable with current. than 50 divided by the number of points on
the circui4 provided that the whole installation
9.3.2.4 Motors and other equipments
need not be required to have an insulation
The following test is made on motor and other resistance greater than one megaohm.
equipment: c) Control rheostats, heating and power
appliances and electric signs, may, if desired,
The insulation resistance of each phase winding against
the frame and between the windings shall be measured. be disconnected from the circuit during the
test, but in that event the insulation resistance
Megger of 500 V or 1000 V rating shall be used. Star
between the case of framework, and all live
points should be discomected. Minimum acceptable
parts of each rheostat, appliance and sign shall
value of the insulation resistance varies with the rated
be not less than that specified in the relevant
power and the rated voltage of the motor.
Indian Standard specification or where there
The following relation may serve as a reasonable is no such specification, shall be not less than
guide: half a megaohm.
d) The insulation resistance shall also be
20x E.
R= measured between all conductors connected
1000+2P
to one pole or phase conductor of the supply
where and all the conductors connected to the middle
R, = Insulation resistance in megohms at 25°C. wire or to the neutral on to the other pole of
phase conductors of the supply. Such a test
E. = Rated phase to phase voltage.
shall be made after removing all metallic
P = Rated power in kW.
connections between the two poles of the
If the resistance is measured at a temperature different installation and in these circumstances the
from 25”C, the value shall be corrected to 25°C. insulation resistance between conductors of
the installation shall be not less than that
The insulation resistance as measured at ambient
specified in (b).
temperature does not always give a reliable value, since
moisture might have been absorbed during shipment 9.3.2.6 Completion certificate
and storage. When the temperature of such a motor is
On completion of an electrical installation (or an
raised, the insulation resistance will initially drop
extension to an installation) a certificate shall be
considerably, even below the acceptable minimum. If
furnished by the contractor, counter-signed by the
any suspicion exists on this score, motor winding must
certified supervisor under whose direct supervision the
be dried out.
installation was carried out. This certificate shall be in
9.3.2.5 Wiring installation a prescribed form as required by the local electric
supply authority. One such recommended form is given
The following tests shall be done:
in Annex E.
a) The insulation resistance shall be measured
9.3.2.7 Earthing
by applying between earth and the whole
system of conductor or any section thereof For checking the efficiency of earthing, the following
with all fuses in place and all switches closed, tests are done:

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 47


T

a) The earth resistance of each electrode shall 10.4 UPS System


be measured.
An electrical device providing an interface between
b) Earth resistance of earthing grid shall be
the mains power supply and sensitive loads (computer
measured. systems, instrumentation, etc). The UPS supplies
c) All electrodes shall be connected to the grid sinusoidal a.c. power free of disturbances and within
and the earth resistance of the entire earthing strict amplitude and frequency tolerances. It is
system shall be measured. generally made up of a rectifier/charger and an inverter
These tests shall preferably be done during the summer together with a battery for backup power in the event
months. of a mains failure with virtually no time lag.

In general UPS system shall be provided for sensitive


10 TELECOMMUNICATION AND OTHER
electronic equipments like computers, printers, fire
MISCELLANEOUS SERVICES
alarm panel, public address system equipment, access
10.1 Telecommunication Service control panel, EPABX, etc with the following
provisions:
10.1.1 House wiring of telephone subscribers offices
in small buildings is normally undertaken by the a) Provisions of isolation transformers shall be
Telephone Department on the surface of walls. But provided where the capacity exceeds 5 kVA.
in large multi- storeyed buildings intended for b) UPS shall have dedicated neutral earthing
commercial, business and office use as well as for system.
residential purposes, wiring for telephone connections c) Adequate rating of protective devices such as
is generally done in a concealed manner through MCB, MCCB, fuses, ELCB, etc, shall be
conduits. provided at both incoming and outgoing sides.
10.1.2 The requirements of telecommunication d) UPS room shall be provided with adequate
facilities like Telephone connections, Private Branch ventilation and/or air conditioning as per
Exchange, Intercommunication facilities, Telex and requirement.
Telegraph lines are to be planned well in advance so
10.5 Inverter
that suitable provisions are made in the building plan
in such a way that the demand for telecommunication In general inverter system shall be provided for house
services in any part of the building at any floor are lighting, shop lighting, etc, with the following
met at any time during the life of the building. provisions:

10.1.3 Layout arrangements, methods for internal a) Adequate rating of protective devices such as
block wiring and other requirements regarding MCB, MCCB, fuses, ELCB, etc, shall be
provisions of space, etc, may be decided defending as provided at both incoming and outgoing sides.
the number of phone outlets and other details in b) Earthing shall be done properly.
consultation with Engineer/Architect and user. c) Adequate ventilation space shall be provided
10.2 Public Address System — See Part 4 ‘Fire and around the battery section of the inverter.
Life Safety’. d) Care in circuit design to keep the connected
load in such a manner that the demand at the
10.3 Common Antenna System for TV Receivers time of mains failure is within the capability
10.3.1 In multistoreyed apartments, houses and hotels of the inverter. (If the inverter fails to take
where many TV receivers are located, a common over the load at the time of the mains failure,
master antenna system may preferably be used to avoid the purpose of pwviding the inverter and
mushrooming of individual antennas. battery back up is defeated.)
e) Circuits which are fed by the UPS or Inverter
10.3.2 Master antenna is generally provided at the top systems should have suitable marking to
most convenient point in any building and a suitable ensure that a workman does not assume that
room on the top most floor or terrace for housing the the power is off, once he has switched off the
amplifier unit, etc, may also be provided in consultation mains from the DB for maintenance.
with the architect/engineer.
0 UPS systems and Inverter systems have a very
10.3.3 From the amplifier rooms, conduits are laid in limited fault fee@g capacity in comparison
recess to facilitate drawing co-axial cable to individual to the mains supply from the licensee’s
flats. Suitable ‘Tap Off’ boxes may be provided in network. The low fault current feed may cause
every room/flat as required. loss of discrimination in the operation of

48 NATIONALBUILDING CODE OF INDIA


MCB’s, if the Inverter or UPS system feeds a 10.8 Security System
number of circuits with more than one over
Security System may be defined as an integrated
current protective device in series (such as
Closed Circuit Television System, Access Control
incoming MCB at the DB and a few outgoing
System, Perimeter Protection Systems, movement
MCB’S). The choice of MCB’s in such cases
sensors, etc. These have a central control panel, which
has to be done keeping the circuit operating and
has a defined history storage capacity. This main
fault condition parameters under both (mains
control panel may be located near to the fire detection
operation and UPS operation) conditions.
and alarm system.
10.6 Diesel Generating Set (less than 5 kVA)
These may be considered for high security areas or
In general small diesel generating sets shall be provided large crowded areas or complexes. High security areas
for small installations such as offices, shops, small scale may consider uncorded, high-resolution, black and
industry, hostels, etc, with the following provisions: white cameras inplace of coloured cameras. These may
be accompanied with movement sensors.
a) These shall be located near the exit or outside
in open areas. Access control may be provided for entry to high
b) They shall be in reach of authorized persons security areas. The systems may have proximity card
only. readers, magnetic readers, etc.
c) Adequate fire fighting equipment shall be
10.9 Computer Networking
provided near such installations.
d) Exhaust from these shall be disposed in such Networking is the practice of linking computing
a way so as not to cause health hazard. devices together with hardware and software
e) These shall have acoustic enclosure, or shall that supports data communications across these
be placed at a location so as not to cause noise devices.
pollution.
10.10 Car Park Management System
f) Adequate ventilation shall be provided around
the installation. The Car Management System may be provided in
multi-level parking or other parking lots where number
!2) Adequate rating of protective devices such as
of vehicles to be parked exceeds 1000 vehicles. The
MCB, MCCB, fuses, ELCB, etc, shall be
Car Park Management System may have features of
provided.
Pay and Display Machines and Parking Guidance
h) Separate and adequate body and neutral
System. The Pay and Display Machines may be
earthings shall be done.
manned and unmanned type. Parking guidance system
10.7 Building Management System needs to display number of car spaces vacant on various
floors, direction of entry and exit, etc. This system can
A building management/automation system may be be of great benefit in evaluating statistical data’s such
considered to be provided for controlling and as number of cars in a day or month or hour, stay time
monitoring of all parameters of HVAC, electrical, of various vehicles, etc.
plumbing, fire fighting, low voltage system such as
telephone, TV, etc. This not only lead to reduction of 11 LIGHTNING PROTECTION OF BUILDINGS
energy consumption, it shall also generate data leading
11.1 Basic Considerations for Protection
to better operation practice and systematic maintenance
scheduling. The total overview provided by a Building Before proceeding with the detailed design of a
Automation System, with a capability to oversee a large lightning protecting system, the following essential
number of operating and environmental parameters on steps should be taken: ‘
real time basis leads to introduction of measures which
a) Decide whether or not the structure needs
lead to further reduction in energy consumption.
protection and, if so, what are the special
It shall also help in reduction of skilled manpower requirements (see 11.1.1) {see good practice
required for operation and maintenance of large for details [8-2(27)] }.
complexes. This system can further linked to other b) Ensure a close liaison between the architect,
systems such as Fire alarm system, public address the builder, the lightning protective system
system, etc for more effective running of services. engineer, and the appropriate authorities
This system can be used for analysis and controlling throughout the design stages.
of all services in a particular complex, leading efficient c) Agree the procedures for testing, commissioning
and optimum utilization of available services. and future maintenance.

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 49


F-’””

11.1.1 Need, for Protection The table below which indicates the relationship between
thunderstorm days per year and lightning flashes per square
Structures with inherent explosive risks; for example, kilometre per year:
explosives factories, stores and dumps and fuel tanks;
Thrarderstonn Lightning Flashes per km2per Year
usually need the highest possible class of lightning
days/year ~
protective system.
For all other structures, the standard of protection 5 0.2 0.1 –0.5
10 0.5 0.15–1
recommended in th% remainder of the Code is 20 1.1 0.3-3
applicable and the only question remaining is whether 30 1.9 0.6-5
to protect or not. 40 2.8 0.8-8
50 3.7 1.2-10
In many cases, the need for protection may be self- 60 4.7 1.8-12
80 6.9 3-17
-evident, for example:
100 9.2 4–20
— where large numbers of people congregate;
— where essential public services are concerned; The effective collection area of a structure is the area
— on the plan of the structure extended in all directions
where the area is one in which lightning
to take account of its height. The edge of the effective
strokes are prevalent;
collection area is displaced from the edge of the
where there are very tall or isolated structures; structure by an amount equal to the height of the
and structure at that point. Hence, for a simple rectangular
— where there are structures of historic or building of length L, width Wand height H metres, the
cultural importance. --
collection area has length (L + 2H) metres and width
However, there are many cases for which a decision is (W+ 2H) metres with four rounded comers formed by
not so easy to make. Various factors effecting the risk quarter circles of radius H metres. This gives a
of being struck and the consequential effects of a stroke collection area, AC (in mz):
in these cases are discussed in 11.1.2 to 11.1.8. A= = (Lx W)+2(LXH)+2(WXH) +TTFF . . . (1)
It must be understood, however, that some factors The probable number of strikes (risk) to the structure
cannot be assessed, and these may override all other per year is:
considerations. For example, a desire that there should
be no avoidable risk to life or that the occupants of a P =ACXN, X104 . . . (2)
building should always feel safe, may decide the It must first be decided whether this risk P is acceptable
question in favour of protection, even though it would or whether some measure of protection is thought
normally be accepted that there was no need. No necessary.
guidance can be given in such matters, but an
assessment can be made taking account of the exposure 11.L3 Suggested Acceptable Risk
risk (that is the risk of the structure being struck) and For the purposes of this Code, the acceptable risk
the following factors: figure has been taken as 10-5, that is, 1 in 100000 per
a) Use to which the structure is put, year.
b) Nature of its construction, 11.1.4 Overall Assessment of Risk
c) Value of its contents or consequential effects,
Having established the value of P, the probable number
d) The location of the structure, and
of strikes to the structure per year [see equation (2)
e) The height of the structure (in the case of in 11.1.2] the next step ?s to apply the ‘weighting
composite structures the overall height). factors’ in Tables 3 and 4.
11.1.2 Estimation of Exposure Risk This is done by multiplying P by the appropriate factors
The probability of a structure or building being struck to see whether the result, the overall weighting factors,
by lightning in any one year is the product of the exceeds the acceptable risk of P = 105 per year.
‘lightning flash density’ and the ‘effective collection
11.1.5 Weighting Factors
area’ of jhe structure. The lightning flash density,
N~, is the number of (flashes to ground) per krti2 per In Tables 3A to 3E, the weighting factor values are
year. given under headings ‘A’ to ‘E’, denoting a relative
degree of importance or risk in ea~h case. The tables
NOTE— For the purposesof this Code,the informationgiven
in Fig. 5 on thunderstormdays per year wouldbe necessaryto are mostly self-explanatory but it may be helpful to
be translated in terms of estimated averageannualdensityNE. say something about the intention of Table 3C.

50 NATIONALBUILDING CODE OF INDIA


Table 3 Overall Assessment of Risk Table 3D Weighting Factor ‘D’
(Clauses 11.1.4 and 11.1.5) (Degree of Isolation)

Table 3A Weighting Factor ‘A’ Degree of Isolation Valueof ‘D’


(Use of Structure) locatedin a large area of structnte.sor
Structure 0.4
trees of the sameor greaterheigh~ for example,
Useto Which Structure is Pot Value of ‘A’ in a large townor forest
Housesandotherbuildingsof comparablesize 0.3 Structure located in an area with few other 1.0
Housesand otherbuildingsof comparablesize 0.7 structuresor trees of similarheight
with outsideaerial Strocture completely isolated or exceeding at 2.0
least twice the height of surroundingstructures
Factories,workshopsand laboratories 1.0 or trees
Officeblocks,hotels, blocks of flats and other 1.2
residentialbuildingsother than thoseincluded
below Table 3E Weighting Factor ‘E’
Places of assembly, for example, churches, 1.3 (Type of Country)
halls, theatres, museums, exhibitions,
departmental stores, post offices, stations, Type of country Vatueof ‘E’
airports,and stadiumstnrctures Flat countryat any level 0.3
Schools,hospitals,children’sand other homes 1.7 Hill country 1.0
Mountaincountrybetween300 m and 900 m 1.3
Table 3B Weighting Factor ‘B’ Mountaincountrybetween900 m 1.7
(Type of Construction)
The effect of the value of the contents of a structure is
Type of Construction Vatue of ‘B’ clears the term ‘consequential effect’ is intended to
Steel framed encasedwith any roof other than 0.2 cover not only material risks to goods and property
metal’)
but also such aspects as the disruption of essential
Reinforced concrete with any roof other than 0.4
metal services of all kinds, particularly in hospitals.
Steel framed encased or reinforced conctete 0.8 The risk to life is generally very small, but if a building
with metalroof
is struck, fire or panic can naturally result. All possible
Brick,plain concreteor masonrywith atIymof 1.0
otherthan metalor thatch steps should, therefore, be taken to reduce these effects,
Timberframedor clad withanyroof ohte tthan 1.4 especially among children, the old, and the sick.
metalor thatch
Brick, plain concrete,masonry,timber framed 1.7 11.1.6 Interpretation of Overall Risk Factor
but with metal roofing The risk factor method put forward here is to be taken
Auybuilding with a thatchedroof 2.0 as giving guidance on what might, in some cases, be a
difficult problem. If the result obtained is considerably
‘) A structure of exposed metal which is continuous down to less than 10-5 (1 in 100 000) then, in the absence of
ground level is excluded from these tables as it requires no
lightingprotectionbeyondadequateearthingarrangements. other overriding considerations, protection does not
appear necessary; if the result is greater than 10-5, say
for example 10q (1 in 10 000) then sound reasons
Table 3C Weighting Factor ‘C’ (Contents or
would be needed to support a decision not to give
Consequential Effects)
protection.
Contents or Consequential Effects Value of ‘C’
When it is thought that the consequential effects will
Ordinary domestic or office buildings, 0.3
factories and workshops not containing be small and that the effect of a lighting stroke will
valuableor speciallysusceptiblecontents most probably be merely sli@t damage to the fabric
Industrial and agricultural buildings with 0.8 of the structure, it may be economic not to incur the
speciallysusceptible‘)contents cost of protection but to accept the risk. Even though,
Powerstations,gas works,teleponeexchanges, 1.0 this decision is made, it is suggested that the calculation
radio stations
is still worthwhile as giving some idea of the magnitude
Industrial key plants, ancient monumentsand 1.3
historic buildings, museums, art gatleries or of the calculated risk being taken.
other buildings with specially valuable
contents 11.1.7 Anomalies
Schools,hospitals,children’sandotherhomes, 1.7
Structures are so varied that any method of assessment
placesof assembly
may lead to anomalies and those who have to decide on
protection must exercise judgement. For example, a
‘) This meansspeciallyvahtableplantor materialsvulnerableto
fire or the resultsof fire. steel-framed building may be found to have a low risk

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 51


factor ht, M the addition of an air termination and and isolated from other structures. The construction is
earthing system will give greatly improved protection, of brick and concrete with a non-metallic roof.
the cost of providing this maybe considered worthwhile.
Is lighting protection needed?
A low risk factor may result fof chimneys made of
a) Flashes/km2/year — Let us say, for the
kmck or concrete. However, where chimneys are free
protection of the hospital a value for N is 0.7.
standing or where they project for more than 4.5 m
above the adjoining structure, they will require b) Collection area — Using equati& (1)
protection regardless of the factor. Such chimneys are, in 11.1.2:
therefore, not covered by the method of assessment. Ac = (70X12) +2(7OX1O)+2(12X1O)
Similarly, structures containing explosives or +(Jt x 100)
flammable substances are also not covered. = 840+ 1 400+240+314
Results of calculations for different structures are given = 2794 m2
in Table 4 and a specific case is worked through c) Probability of being struck — Using equation
in 11.1.8. (2) in 11.1.2:
11.1.8 Sample Calculation of Need for Protection P = A x N x 10< times per year

A hospital building is 10 m high and covers an area of = 2>94 ; 0.7 X 10A


70 m x 12 m. The hospital is located in flat country = 2.0 x 10-3 approximately

Table 4 Examples of Calculations for Evaluating the Need for Protection

(Clauses 11.1.4 and 11.1.7)

S1 Description Risk of Being Struck (P) “ Weighting Factors Overall


Overall Recommen-
No. of Structure Risk dation
~ ~ ;;:
Factor
Collection Flash P ‘A’ ‘B’ ‘c’ ‘D’ ‘E’ Factor (product
ha Density ACx Ng
Use of Type of Contents or Degree Type of (Product of COIS 5
Ac Ng x 104 Structure Const- Consequen- of Country of and 11)
(Table ruction tial Effects Isolation (Table COIS6-10)
3A) (Table (Table 3C) ‘~~~ -3E)
3B) ‘
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13)

i) NIalsonette, 3327 0.6 2 x 10-3 1.2 0.4 0.3 0.4 0.3 0.02 4 x 10-5 Protection
n3nforced required
concrete and
brick built,
non-metallic
roof
ii) Offke 4296 0.6 2.6 X 10-3 1.2 0.4 0.3 0.4 0.3 0.02 5.2 x 10-5Protection
building, required
reinforced
concrete
construction,
non-metallic
roof
iii) School, brick 1456 0.7 1 x 10-3 1.7 1.0 1.7 0.4 0.3 0.3 3 x 10q Protection
built required
iv) 3 bedroom 405 0.4 1.6 X 10q 0.3 1.0 0.3 0.4 0.3 0.01 1.6 X 10q No
detached protection
dwelling required
house, brick
built
v) Village 5027 0.6 3 x 10-3 1.3 1.0 1.7 2.0 0.3 1.3 3.9 x 10-3Protection
church required

NOTE — The risk of being struck, ‘P’ (CO15), is multiplied by the product of the weighting factors(CO16to 10) to yield an overall risk
factor (CO112). This should be compared with the acceptable risk (1 x 10-5)for guidance on whether or not to protect.

52 NATIONAL BUILDING CODE OF INDIA


d) Applying the weighting factors Therefore, the overall risk factor
A = 1.7 = 2.0x 1.7 x 10-3
B=l
= 3.4x 10”3
c = 1.7
D = 2.0 Conclusion: Protection is necessary.
E = 0.3 11.2 For detailed requirements of lightning protection
The overall multiplying factor of various structures, reference may be made to good
=AxBxCXDXE practice [8-2(27)].
= 1.7

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 53


sl Name of ArmUal sl Name of Annual S1 Nme of Annual
MO. Place Z’hunakr- No. Place Thuna!er- No. Place Thunder-
storm Days storm Days storm Days

1. Gilgit ‘7 63. Dwnka 63 125. Nagpur 45


2. Slcardu 5 64. Ilujeehg 28 126. Gtmdia 10
3. Guhnarg 53 65. Jalpaiguri 68 127. Aurangabad 34
4. Srinagar 54 66. Ivlalda 59 128. Bominty 16
5. Dras 3 67. Asansol ’71 129, Ali* , 12
6. IQrgil 2 68. Bwdwan 39 130. AhnMmgw 10
7. Leh 3 69. Kharagplr 76 131. Palbhani 32
8. .lamrnu 26 70. Calcutta 70 132. Pune 22
9. Dharmsala 13 71. Sagar Island 41 133. Mahabaleshwar 14
10. Amritsar 49 72. Dlnlbri 8’ 134. Ratnagiri 6
11. F’athankot 4 73. Tezpur 27 135. Sidapur 23
12. Mandi 46 74. Dibrugarh 98 136. Miraj 25
13. Ludhiana 12 75. Sibsagar 103 137. Vengnrla 39
14. Simla 40 76. Shillong 75 . 138. Nizambad 36
15. Patiala 26 77. Cherrapunji 49 139. Hnamkonda 43
16. Ambala 9 78. Silchar 33 140. Hyderabad 28
17. Hissar 27 79. Kohima 34 141. Khammam 26
18. Delhi 30 80. Imphal 49 142. Kalingapatam 20
19. Bikaner 10 81. Deesa 7 143. Vishakapatnam 46
20. Phalodi 14 82. Dwarka 5 144. Rentichintala 42
21. Sikar 17 83. Jamnagar 8 145. Mastilpatam 20 --
22. Barmer 12 84. Rajkot 12 146. Ongole 25
23. Jodhpur 23 85. Ahmedabad 11 147. Kumool 29
24. Ajmer 26 86. Dohad 17 148. Anantpur 22
25. Jaipur 39 87. Porbandar 3 149. Nellore 18
26. Kankroli 36 88. Veraval 3 150. Bidar 15
27. Mount Abu 5 89. Bhavnagar 11 151. Gulbarga 34
28. Udaipur 38 90. Baroda 8 152. Bijapur 9
29. Neemuch 28 91. Surat 4 153. Belgaum 31
30. Kota 27 92. Gwalior 53 154. Raichur 17
31. Jhalawar 40 93. Guna 33 155. Gadag. 21
32. Mussorie 61 94. Nowgong 59 156. Bellary 22
33. Roorkee 74 95. Satna 41 157. Karwar 27
34. Najibabad 36 96. Sagar 36 158. Honavar 5
35. Muktesww 53 97. Bhopal 44 159. Chikalthma 24
36. Meerut — 98. Jabalpur 50 160. Mangalom 36
37. Bareilly 34 99. Umaria 37 161. Hassan 26
38. Aligarh 30 100. Ambikapur 29 162. Bangalore 46
39. Agra 24 101. Indore 34 163. Mysore 44
40. Mainpun 23 102. Hoshangabad 37 164. Kozhikode 39
41. Bahraich 31 103. Panchmarhi 30 165. Palghat 35
42. Gonda 22 104. Seoni 51 166. CoChin 69
43. Lucknow 18 105. Pendadah 56 167. Alleppey 51
44. Kanpur 26 106. Raipur 34 168. Trivandrum 68
45. Fatehpur 24 107. Chhindwara 27 169. Vellore 25
46. Jhansi 20 108. Kanker 37 170. Madras 47
47. Allahabad 51 109. Jagdalpur 35 171. Ootacamund 24
48. Varanasi 51 110. Balasore 81 172. Salem 69
49. Azamgarh 1 111. Chandbali 75 173. Cu$dalore 37
50. Gorakhpur 11 112. Angul 81 174. Coimbatore 40
51. Kathmandu 74 113. Bhubaneswar 46 175. Trichchirapalli 41
52. Motihari 38 114. pun 33 176. Nagappattinam 15
53. Darbhanga 10 115. Gopalpur 34 177. Kodaikanal 82
54. Patna 33 116. Jharsuguda 85 178. Madurai 39
55. Gaya 38 117. Sambalpur 67 179. Parnban 5
56. Daltonganj 73 118. Titlagarh 24 180. TuticoM 14
57. Hazaribagh 73 119. Rajgangpur 1 181. Cape Comorin 68
58. Ranchi 34 120. Dahanu 1 182. Port Blair 62
59. Chaibasa 70 121. Nasik 17 183. Car Nicobar 1 18
60. Jamshedpur 66 122. Malegaon 13 184. MiniCoy 1 20
61. Purnea 52 123. Akola 20
62. Sabour 76 124. Amraoti 32

54 NATIONALBUILDINGCODEOFINDIA
.

44” 7a- 76” 40” d d ?2” $4”


I >-.%-~”l. J
; I I
I

INDIA
PLACES FOR AVERAGE NUMBER OF
~. ,8 THUNDERSTORM DAYS
-*3A ●&w
9 ~~
‘1
IN A YEAR J
;

,S “- @
I al

““ 98.~99------
56* ;7, y, ‘“~ .Lt%..
-L-”” ””-”--”- 1
m “---”ma -“-”o--~ ‘-

\-NSWMOOFf \ I
P
.1 2 7 .-. ---

Ill
I *
m--- ----
m
*
129 ,132 ,35 109●

1\
,138 BAY OF
ARABIAN ● 133 ● 0150 BENGAL
,139
SEA 136 ●
●
● *4O ● 141 145 7
134
&*; 1$ @
137
1550 154
I 157’ f560 ● 148 ●

I b
158 ● 159 149 ● [

o~-
$, f$
4
. WC&
168
184
181 %
I INDIAN OCFAN I I k

Based upon Survey of India Outline Map printed in 1993. @ Government of India Copyright, 2005

The territorial waters of India extend into the seato a distance of twelve nautical miles measured tiom the appropriate base line.
The boundary of Meghalaya shown on this map is as interpreted from the North-Eastern Areas (Reorganisation) Act, 1971, but has yet to be verified.
Responsibility for correctness of internal details shown on the map rests with the publisher,
The state boundaries between Uttaranchal & Uttar Pradesh, Bihar& Jharkhand and Chhatisgarh & Madhya Pradesh have not been verified by Governments cawemed.

FIG. 5 MAP OFINDIASHOWINGPLACESFORAVERAGENUMBEROFTHUNDERSTORM


DAYS INA YEAR

PART 8 BUILDING SERVICES — SECTION 2 ELECTRICAL AND ALLIED INSTALLATIONS 55


ANNEX A
(Clause 2.2)
DRAWING SYMBOLS FOR ELECTRICAL INSTALLATION IN BUILDING

A-1 WIRING A-2.2.3 Distribution Fuse Board lzzzzzl


A-LO Remarks ‘upwards’ and ‘downwards’ apply Without Switches
only when the drawing is read the right way up.
A-2.2.4 Distribution Fuse Board with ~~[
A-1.O.1 An arrow on the slant line indicates the Switches
direction of the power flow.
A-3 SWITCHES AND SWITCH-OUTLETS
A-1.O.2 The wiring terminates at the circle or the black
dot. A-3.1 One-Way Switch

A-1.l General Whing A-3.1.1 Single-Pole #


A-1.2 Wiring on the Surface mm
A-3.1.2 Two-Pole #
A-1.3 Wiring under the SUrfaCe ~
A-.1.4 Wiring in Conduit A-3.1.3 Three-Pole 8

* A-3.2 Single-Pole Pull Switch


A-1.4.1 Conduit on Surj4ace /

A-1.4.2 Concealed Conduit L4/c)u A-3.3 MuItiposition Switch for


v
Different Degrees of Lighting
NOTE— The type of conduitmaybe indicated,if necessary.

A-1.5 Wiring Going Upwards d A-3.4 Two-Way Switch


/

A-1.6 Wiring Going Downwards


)’ A-3.5 Intermediate Switch
x

A-1.7 Wiring Passing Vertically


through a Room
/0” A-3.6 Period Limiting Switch
dt

A-3.7 Time Switch 1~[


A-2 FUSE BOARDS

A-2.1 Lighting Circuit Fuse Boards A-3.8 Pendant Switch P

A-2.1.1 Main Fuse Board Without A-3.9 Push Button


Q
Switches
NOTE — The use of tlx+push button may be indicated, if
desired.
A-2.1.2 Main Fuse Board with
Switching
A-3.1O Luminous PUS4Button @
A-2.1.3 Distribution Fuse Board
A-3.11 Restricted Access Push Button ~
Without Switches

A-2.1.4 Distribution Fuse Board with A-4 SOCKET-OUTLETS

Switches

A-2.2 Power Circuit Fuse Boards


A-4.1 Socket-Outlet, 6A A
A-2.2.1 Main Fuse Board Without A-4.2 Socket-Outlet, 16A A
n
Switches
A-4.3 Combined Switch and Socket-
K
A-2.2.2 Main Fuse Board with Switches Outlet, 6A

56 NATIONALBUILDINGCODEOFINDIA
A-4.4 Combined Switch and Socket- A-
~ A-5.15 Spot Light
(
xx
Outlet, 16A

A-4.5 Interlocking Switch and Socket-


A-5.16 Flood Light
(
x:
M
Outlet, 6A
A-5.17 Flourescent Lamp
A-4.6 Interlocking Switch and Socket-
K
n
A-5.17.1 Group of Three 40-W ~ ~ 3 x40w
Outlet, 16A
Fluorescent Lumps
A-5 LAMPS AND LIGHTING APPARATUS
A-6 ELECTRICAL APPLIANCES
A-5JI Symbols A-5.1 to A-5.17.1 represent either the
lamp or a group of lamps or the outlet for lamps. If it A-6.1 General I
is desired to specify that the lamp is fixed to the wall
NOTE— If necessary,use designationis specify.
or coiling, a vertical or horizontal line respectively may
be added to the symbol. A-6.2 Heater 111[
A-5.1 Lamp or Outlet for Lamp x A-6.3 Storage Type Electric Water +={
Heaters
A-5.LI Group of Three 40-W Lumps x 3X40VV

A-7 BELLS, BUZZERS AND SIRENS


A-5.2 Lamp, Mounted on a Wall k
A-7.1 Bell R
A-5.3 Lamp, Mounted on a Ceiling x A-7.2 Buzzer x

A-5.4 Counter Weight Lamp Fixture F A-7.3 Siren


@

A-7.4 Horn on Hooter K1


A-5.5 Chain Lamp Fixture
z A-7.5 Indicator (at ‘N’ insert m
number of ways)
A-5.6 Rod Lamp Fixture
37 A-8 FANS

A-5.7 Lamp Fixtures with Built-in A-8.1 Ceiling Fan a)


.x’ .
Switch

A-5.8 Lamp Fed from Variable Voltage ~


A-8.2 Bracket Fan
8
supply
A-8.3 Exhaust Fan
A-5.9 Emergency Lamp x @

A-8.4 Fan Regulator


❑
A-5.1O Panic Lamp
x A-9 TELECOMMUNICATION APPARATUS
A-5.11 Bulk-Head Lamp Q$J
A-9.1 Socket-Outlet for
r-+
Telecommunications
A-5.12 Water-Tight Lighting Fitting w
R

A-5.13 Battern Lamp Holder


K
BH
A-9.2 Aerial
Y
A-5.14 Projector
cx A-9.3 Loudspeaker
a

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 57


A-n FIRE ALARMS
A-9.4 Radio Receiving Set

A-11.l Manual Operated Fire A1arm


u
A-9.5 Amplifying Equipment

A-9.6 Television Receiving Set


A-11.2 Automatic Fire Detector Switch
❑
A-9.7 Control Board
A-11.3 Bell Connected to Fire Alarm
(for Public Address System) fl
Switch
A-10 CLOCKS

A-IL4 F~re Alarm Indicator s


A-10.1 Synchronous Clock H

A-12 EARTHING
A-10.2 Impulse Clock Outlet
A-12.1 Earth Point

A-10.3 Master Clock Outlet

ANNEX B
[Clauses 3.1,5.3.1.1,5.3.1.3, 5.3.2.3(b) ad 8.6]
EXTRACTS FROM INDIAN ELECTRICITY RULES, 1956

B-1 The following are the extracts of some of the c) In all other cases, at a point corresponding
rules: to the point of commencement of supply
or at such other point as may be approved
Rule 32, Identification of Earthed and Earthed by an Inspector or any officer appointed
Neutral Conductors and Position of Switches and to assist the Inspector and hold authorized
Cut-Outs Therein under sub-rule (2) of Rule 4-A.
Where the conductors include an earthed conductor of 2) No cut-out, link or switch other than a linked
a two-wire system or an earthed neutral conductor of switch arranged to operate simultaneously on
a multi-wire system or a conductor which is to be the earthed or earthed neutral conductor and
connected thereto, the following conditions shall be live conductors shall be inserted or remain
complied with: inserted in any earthed or earthed neutral
conductor of a two-wire system or in any
1) An indication of permanent nature shall be
earthed or earthed neutral conductor of a
provided by the owner of the earthed or
multi-wire system or in any conductor
earthed neutral conductor, or the conductor
connected thereto with the following
which is to be connected thereto, to enable
exceptions:
such conductor to be distinguished from any
a) A link for testing purposes, or
live conductor. Such indication shall be
provided: b) A switch for use in controlling a generator
or transformer.
a) Where the earthed or earthed neutral
NOTE — For the purpose of this rule, the relevant
conductor is the property of the supplier,
Indian Standards relating to markingand arrangement
at or near the point of commencement of for switchgear,busbar,mainconnections,and auxiliary
supply ; wiringmay be referredto.
b) Where a conductor forming part of a
Rule 33 Earthed Terminal on Consumer’s Premises
consumer’s system is to be connected to
the supplier’s earthed or earthed neutral 1) The supplier shall provide and maintain on
conductor at the point where such the consumer’s premises for the consumer’s
connection is to be made; use a suitable earthed terminal in an accessible

58 NATIONALBUILDING CODE OF INDIA


position at or near the point of commencement on the primary side of the transformer
of supply as defined under Rule 58; may be of such capacity as to carry the
Provided that in the case of medium, high or full load current and to break only the
extra-high voltage installation, the consum& magnetizing current of the transformer.
shall, in addition to aforementioned earthing Provided further that the provision of the
arrangement, provide his own earthing system clause shall not apply to transformers
with an independent electrode, and maintain installed in sub-station upto and
the same. including 100 kVA belonging to the
Provided further that the supplier may not supplier.
provide any earthed terminal in the case of Provided also that the provision of a
installations already connected to his system linked switch on the primary side of the
on or before the 30th June, 1966 if he is transformer shall not apply to the unit
satisfied that the consumer’s earthing auxiliary transformer of the generator.
arrangement is efficient. c) Except in the case of composite control
2) The consumer shall take all reasonable gear designed as a unit; every distinct
precautions to prevent mechanical damage to circuit is protected against excess energy
the earthed terminal and its lead belonging to by means of a suitable cut-out or a circuit-
the supplier; and breaker of adequate breaking capacity
suitably located and so constructed as to
3) The supplier may recover from the consumer
prevent danger from overheating, arcing
the co-s; of installation of such earthed
or scattering of hot metal when it comes --
terminal on the basis laid down in sub-rule (2) into operation and to permit of ready
of Rule 82. renewal of the fusible metal of the cut-
out without danger.
Rule 50 Supply and Use of Energy
d) The supply of energy to each motor or a
1) The energy shall not be supplied, transformed, group of motors or other apparatus,
converted or used or continued to be supplied, meant for operating one particular
transformed, converted or used unless the machine, is controlled by a suitable
following provisions are observed: linked switch or a circuit-breaker or an
a) A suitable linked switch or a circuit emergency tripping device with manual
breaker of requisite capacity to carry and reset of requisite capacity placed in such
break the current is placed as near a position as to be adjacent to the motor
as possible to, but after the point of or a group of motors or other apparatus,
commencement of supply, as defined readily accessible to and easily operated
under Rule 58, so as to be readily by the person in charge and so connected
accessible and capable of being easily in the circuit of that by its means all
operated to completely isolate the supply supply of energy can be cut-off from the
to the installation, such equipment being motor or a group of motors or apparatus
in addition to any equipment installed and from any regulating switch,
for controlling individual circuits or resistance or other device associated
apparatus. therewith.
Provided that where the point of e) All insulating material is chosen with
commencement of supply and the special regard to the circumstances of its
consumer’s apparatus are near to each proposed use, the mechanical strength
other, one linked switch or circuit breaker being sufficient for the purpose, and so
near the point of commencement of far as is practicable, is of such a character
supply shall considered sufficient for the or so protected as to maintain adequately
purpose of this rule; the insulating properties under all
b) A suitable linked switch or circuit- working conditions in respect of
breaker of requisite capacity to carry and temperature and moisture; and
break the full load current is inserted on f) Adequate precautions are taken to ensure
the secondary side of a transformer, in that no live parts are so exposed as to
the case of high or extra high voltage cause danger.
installation. 2) a) When energy is being supplied,
Provided however, that the linked switch transformed, converted or used, the

PART 8 BUILDINGSERVICES — SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 59


consumer or the owner of the concerned iii) if the space behind the switchboard
installation shall be responsible for the exceeds 75 cm in width, there shall
continuous observance of the provisions be passage way from either end of
of sub-rule(1) in respect of his the switchboard clear to a height of
installation. 1.8 metres.
b) Every consumer shall use all reasonable 2) Where an amlication has been made to
means to ensure that where energy is a supplier for supply of energy to any
supplied by a supplier no person other installation, the shall not commence, or
than the supplier shall interfere with the where the supply has been discontinued,
service lines and apparatus placed by the recommence the supply unless he is satisfied
supplier on the premises of the consumer. that ,tie consumer has complied in all respects
with the conditions of supply, set out in sub-
Rule 51 Provisions Applicable to Medium, High or
rule (1) of this rule and Rules 50 and 64.
Extra-High Voltage Installations
3) Where a supplier proposes to supply or use
The following provisions shall be observed where energy at medium voltage or to recommence
energy at medium, high or extra high voltage is supply after it has been discontinued for
supplied, converted, transformed or used: a period of six months, he shall, before
connecting or re-connecting the supply, give P
1) a) All conductors (other than those of
notice in writing of such intention to the
overhead lines) shall be completely
Inspector.
enclosed in mechanically strong metal
4) If at any time after connecting the supply the “s
casing or metallic covering which is
electrically and mechanical continuous upplier is satisfiedthat any provision of sub- %
and adequately protected against rule (1) of this rule, or of Rules 50 and 64 is
mechanical damage unless the said not being observed he shall give notice of
conductors are accessible only to an the same in writing to the consumer and the
authorised person or are installed and Inspector specifying how the provision has
protected to the satisfaction of the not been observed and may discontinue the
Inspector so as to prevent danger. supply if the Inspector so direct.

Provided that rigid non-metallic conduits Rule 58 Point of Commencement of Supply


conforming to IS 2509: 1963 ‘Rigid
The point of commencement of supply of energy to a
non-metallic conduits for electrical
consumer shall be deemed to be the point at the
installation’, may be used for medium
outgoing terminals of the cut-outs inserted by the
voltage installation subject to any
supplier in each conductor of every service line other
conditions as the Inspector or officer
than an earthed or earthed neutral conductor or the
appointed to assist an Inspector may
earthed external conductor of .a concentric cable at the
think fit to impose.
consumer’s premises.
b) All metal works enclosing, supporting or
associated with the installation, other than Rule 61 Connection with Earth
that designed to serve as a conductor
1) The following provisions shall apply to the
shall, if considered necessary by the
connection with earth of systems at low
Inspector, be connected with earth.
voltage in cases where the voltage between
c) Every switchboard shall comply with the phases or outers normally exceeds 125 volts
following provisions, namely: and of systems ar medium voltage:
i) a clear space of not less than one a) The neutral conductor of a three-phase
metre in width shall be provided in four-wire systenL and the middle conductor
front of the switchboard; of a two-phase three-wire system shall
ii) if there are any attachments or bare be earthed by not less than two separate
connections at the back of the and distinct connections with earth both
switchboard, the space (if any) at the generating station and at the
behind the switchboard shall be substation. It may also be earthed at one
either less than 10 cm, or more than or more points along the distribution
75 cm in width, measured from the system or service line in addition to any
farthest outstanding part of any connection with earth which may be at
attachment or conductor; and the consumer’s premises.

60 NATIONALBUILDING CODE OF INDIA


b) In the case of a system comprising the metal sheathing and metallic
electric supply lines having concentric armouring (if any) of the electric supply
cables, the external conductor of such lines concerned.
cables shall be earthed by two separate 2) The frame of every generator, stationary
and distinct connections with earth. motor, portable motor, and the metallic
c) The connection with earth may include a parts (not intended as conductors) of all
link by means of which the connection transformers and any other apparatus used for
may be temporarily interrupted for regulating or controlling energy and all
the purpose of testing or for locating a medium voltage energy consuming apparatus
fault. shall be earthed by the owner by two separate
d) i) In a direct current three-wire system and.distinct connections with earth.
the middle conductor shall be earthed 3) All metal casings or metaIlic covering
at the generating station only, and the containing or protecting any electric supply-
current from the middle conductor to line or apparatus shall be connected with earth
earth shall be continuously recorded and shall be so joined and connected across
by means of recording ammeter, and all junction boxes and other openings as
if at any time the current exceeds one to make good mechanical and electrical
thousandth part of the maximum connections throughout their whole length.
supply current, immediate steps shall Provided that where the supply is at low
be taken to improve the insulation of voltage, this sub-rule shall not apply to
the system. isolated wall tubes or to brackets, electrollers,
ii) Where the middle conductor is switches, ceiling fans or other fittings (other
earthed by means of a circuit-breaker than portable hand lamps and portable and
transportable apparatus) unless provided with
with a resistance connected in parallel,
earth terminal.
the resistance shall not exceed 10
ohms and on the opening of the circuit- Provided further that where the supply is at
breaker, immediate steps shall be low voltage and where the installations are
taken to improve the insulation of the either new or renovated all plug sockets shall
system, and the circuit-breaker shall be of the three-pin type, having permanently
be re-closed as soon as possible. and efficiently earthed.
iii) The resistance shall be used only as The sub-rule shall come into force
a protection for the ammeter in case immediately in the case of new installations
of earths on the system and until such and in the case of existing installations the
earths are removed, immediate steps provisions of this sub-rule shall be complied
shall be taken to locate and remove with before the expiry of a period of two years
the earth. from the commencement of those rules.
e) In the case of an alternating current 4) All earthing systems shall before electric
system, there shall not be inserted in the supply lines or apparatus are energized, be
connection with earth and impedance tested for electrical resistance to ensure
(other than that required solely for the efficient earthing.
operation of switch gear or instrument), 5) All earthing systems belonging to the supplier
cut-out or circuit-breaker, and the result shall, in addition, be tested for resistance on
of any test made to ascertain whether the dry day during t$e dry season not less than
current (if any) passing through the once every two years.
connection with earth is normal, shall be 6) A record of every earth test made and the
duly recorded by the supplier. result thereof shall be kept by the supplier for
f) No person shall make connection with a period of not less than two years after the
earth by the aid of, nor shall be keep it in day of testing and shall be available to the
contact with any water main not Inspector or any officer appointed to assist
belonging to him except with the consent the Inspector and authorised under sub-rule
of the owner thereof and of the Inspector. (2) of Rule 4A when required.
g) Alternating current systems which are
Rule64Use of Energy at High and Extra-High Voltage
connected with earth as aforesaid maybe
electrically interconnected, provided that 1) The Inspector shall not authorise the supplier
each connection with earth is bonded to to commence supply, or where the supply has

PART 8 BUILDINGSERVICES — SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 61


been discontinued for a period of one year be located in the basement where
and above, tore-commence the supply at high proper oil drainage arrangements
or extra-high voltage to any consumer unless: cannot be provided.
a) all conductors and apparatus intended for ii) Where a substation or switch station
use at high or extra-high voltage and with apparatus having more than
situated on the premises of the consumer 2000 litres of oil is installed whether
are inaccessible except to an authorised indoors or outdoors, the following
person and all operations in connection measures shall be taken, namely:
with the said conductors and apparatus are (a) baffle walls shall be erected
carried out only by an authorised person; between the apparatus containing
b) the consumer has provided and agrees to more than 2000 litres of oil
maintain a separate building or a locked and the adjacent apparatus to
weather-proof and fire-proof enclosure prevent spread of fme and avoid
of agreed sign and location, to which the damagw
supplier shall at all times have access for (b) a drain valve of adequate size
the purpose of housing is high or extra- which shall be capable of being
high voltage apparatus and metering safely operated even when the
equipment, or where the provision apparatus has caught fire shall be
of a separate building or enclosure provided, and such a valve shall
is impracticable, the consumer has be easily accessible to being
segregated the aforesaid apparatus of the operated and at the same time not
supplier from any other part of his own susceptible to being operated
apparatus: inadvertently;
Provided that such segregation shall be (c) the drain valve shall let out the
by the provision of fire-proof walls, if oil to a covered drainage system
the Inspector considers it to be necessary: which shall take away the oil to
Provided further that in the case of an a place away from the danger
out-door installation the consumer shall zone,
suitably segregate the aforesaid apparatus iii) the above measures shall be taken in
belonging to the supplier from his own addition to other fire protection
to the satisfaction of the Inspector. arrangements to be provided for
c) all pole type substations are constructed quenching the fire in the apparatus;
and maintained in accordance with iv) cable trenches inside the substations
Rule 69. and switch stations containing cables
2) The following provisions shall be observed shall be filled with sand, pebbles or
where energy at high or extra-high voltage is similar non-inflammable materials,
supplied, converted, transformed or used: or completely covered with non-
a) All conductors or live parts of any inflammable slabs.
apparatus shall ordinarily be inaccessible. e) Unless the conditions are such that all the
b) All windings, at high or extra-high conductors and apparatus for use at high
voltage of motors or other apparatus or extra-high voltage maybe made dead
within reach from any position in which at the same time for other work thereon,
a person may require to be suitably the said conductors and apparatus shall
protected so as to prevent danger. be so arrangdd that they may be made
c) Where transformer or transformers are dead in sections, and that work on any
used, suitable provision shall be made, section made dead may be carried on by
either by connecting with earth voltage an authorised person without danger.
or otherwise, to guard against danger by f) Only persons authorised under sub-rule
reason of the said circuit becoming (1) of Rule 3 carry out the work on live
accidentally charged above its normal lines and apparatus.
voltage by leakage from or contact with g) Adequate precautions shall be taken to
the circuit at the higher voltage. prevent unauthorised access to any
d) i) A substation or switch station with part of the installation designed to be
apparatus having more than electrically charged at high or extra-high
2000 litres of oil shall not ordinarily voltage.

62 NATIONALBUILDINGCODEOFINDIA
ANNEX C
[Clause 4.2.4(b)]

AREA REQUIRED FOR TRANSFORMER ROOM AND SUBSTATION


FOR DIFFERENT CAPACITIES

C-1 The requirement for area for transformer room and substation for different capacities of transformers is
given below for guidance:

S1 CapaciQ of Total Transformer Total Substation Area (In Coming, Suggested Minimum
No. Transformer(s) Room Area, H~ MV Panels, Transformer Roof but Face Width
kVA Minimum, m2 Without Generators), Minimum m
(1) (2) (3) (4) (5)
i) 1 X 160 14.0 90 9.0
ii) 2x 160 28.0 118 13.5
iii) 1 X 250 15.0 91 9.0
iv) 2 X 250 30.0 121 13.5
v) 1 x 400 16.5 9.0
vi) 2 x 400 33.0 1; 13.5
vii) 3 x 400 49.5 167 18.0
viii) 2 x 500 36.0 130 14.5
ix) 3 x 500 54.0 172 19.0
x) 2 X 630 36.0 132 14.5
xi) 3 X 630 54.0 176 19.0
xii) 2 X 800 39.0 135 14.5
xiii) 3 X 800 58.0 181 14.0
xiv) 2X1OOO 39.0 149 14.5
xv) 3X1OOO 58.0 197 19.0
NOTES
1 Theabovedimensionsare overallamarequiredfor substationexcludinggeneratingset.
2 The clear heightrequiredfor substationequipmentshallbe minimumof 3.0 m belowthe sotlt of the beam.

ANNEX D
[Clause 4.2.4(j)]
ADDITIONAL AREA REQUIRED FOR GENERATOR IN ELECTRIC SUBSTATION

D-1 The requirement of additional area for generator in electric substation for different capacities of generators
is given below for guidance:

S1 No. Capacity Area Clear Height below the Sojjit of the Beam
kW m2 m
(1) (2) (3) (4)

i) 25 56 3.6
ii) 48 56 3.6
iii) 100 65 3.6
iv) 150 72 4.6
v) 248 100 4.6
vi) 350 100 4.6
vii) 480 100 4.6
viii) 600 110 4.6
ix) 800 120 4.6
x) 1000 120 4.6
xi) 1250 120 4.6
xii) 1600 150 4.6
NOTE— The area and height requiredfor generatingset room given in the above table are for generatguidanceonly and maybe
finallyf~ed accordingto actuatrequirements.

PART 8 BUtLDING SERVICES — SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 63


ANNEX E
(Clause 9.3.2.6)
FORM OF COMPLETION CERTIFICATE

I/We certify that the installation detailed below has been installed by me/us and tested and that to the best of my/
our knowledge and belief, it complies with Indian Electricity Rules, 1956.

Electrical Installation at

Voltage and system of supply

Particulars of Works:
a) Internal Electrical Installation

No. Total Load Type of system of wiring


i) Light point
ii) Fan point
iii) Plug point
3-pin 6 A
3-pin 16A
b) Others Description hp/kW Type of starting

1) Motors:
i)
ii)
iii)
2) Other plants:
c) If the work involves installations of
over head line and/or underground cable
1) i) Type and description of overheadline.
ii) Total length and number of spans.
iii) No. of street lights and its description.
2) i) Total length of underground cable and its size:
ii) No. of joints:
End joint:
Tee joint:
Straight through joint:
Earthing:
i) Description of earthing electrode
ii) No. of earth electrodes
iii) Size of main earth lead

Test Results:
a) Insulation Resistance
i) Insulation resistance of the whole system of conductors to earth . . . . . . . . . . . . . . . .. Megaohms.
ii) Insulation resistance between the phase conductor and neutral
Between phase R and neutral ....................... Megaohms.
Between phase Y and neutral ....................... Megaohms.
Between phase B and neutral ....................... Megaohms.
iii) Insulation resistance between the phase conductors in case of polyphase supply.
Between phase R and phase Y ...................... Megaohms
Between phase Y and phase B ...................... Megaohms
Between phase B and phase R ...................... Megaohms

64 NATIONALBUILDINGCODEOFINDIA
b) Polarity test:
Polarity of non-linked single pole branch switches
c) Earth continuity test:
Maximum resistance between any point in the earth continuity conductor including metal
conduits and main earthing lead ......................... ohms.
d) Earth electrode resistance:
Resistance of each earth electrode.
i) ......................... Ohms.
ii) ......................... Ohms.
iii) ......................... Ohms.
iv) ......................... Ohms.
e) Lightning protective system.
Resistance of the whole of lightning protective system to earth before any bonding is effected
with earth electrode and metal itionthe s~cmre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. Ohms.

Signature of Supervisor Signature of Contractor

Name and Address Name and Address


........................................................ ............................................................
........................................................ ............................................................
........................................................ ............................................................
........................................................ ............................................................

LIST OF STANDARDS

The following list records those standards which are 1S No. Title
acceptable as ‘good practice’ and ‘accepted standards’ diagrams in the field of
in the fulfillment of the requirements of the Code. The electrotechnology:
latest version of a standard shall be adopted at the time (Part 6): 1987 Protection and conversion of
of the enforcement of the Code. The standards electrical energy
listed may be used by the Authority as a guide in (Part 7): 1987 Switchgear, controlgear and
conformance with the requirements of the referred protective devices
clauses in the Code. (2) 7752 Guide for improvement of
Title (Part 1): 1975 power factor in consumer
1s No.
installation: Part 1 Low and
(1) 8270 Guide for preparation of medium supply voltages
(Part 1): 1976 diagrams, charts and tables
(3) 5216 Recommendations on safety
for electrotechnology: Part 1
procedures and practices in
Definitions and classification
electrical work:
1885 Electrotechnical vocabulary:
(Part 1): 1982 General @rst revision)
(Part 16/Sec 3) Lighting, Section 3 Lamps
1967 and auxiliary apparatus (Part 2): 1982 Life saving techniques (first
revision)
(Part 17) :1979 Switchgear and controlgear
(4) 10118 Code of practice for selection,
(jirst revision)
(Part 2): 1982 installation and maintenance
(Part 32) :1993 Electrical cables (first of switchgear and controlgeac
revision) Part 2 Selection
(Part 78) :1993 Generation, transmission and (5) 1646:1997 Code of practice for fire
distribution of electricity — safety of buildings (general):
General Electrical installations
12032 Graphical symbols for (second revision)

PART 8 BUILDINGSERVICES — SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 65


1S No. Title IS No. Title
(6) 732:1989 Code of practice for electrical (Part 4/see 1): Contractors and motor-starters,
wiring installations (third 1993 Section 1 Electro-technical
revision) contractors and motor starters
1255:1983 Code of practice for (Pal 5/See 1): Control circuit devices and
installation and maintenance 1993 switching elements, Section 1
of power cables (up to and Electro-technical control
including 33 kV rating) circuit devices
(second revision) (12) 3961 Recommended current
(7) 13947:1993 Specification for low-voltage ratings for cables:
switchgear and controlgear (Part 1): 1967 Paper insulated lead sheathed
(8) 2148:1981 Specification for flame-proof cables
enclosures of electrical (Part 2): 1967 PVC insulated and PVC
apparatus (second revision) sheathed heavy duty cables
(9) 5578:1985 Guide for marking of (Part 3): 1968 Rubber insulated cables
insulated conductors (first (Part 5): 1968 PVC insulated light duty
revision) cables
(10) 1777:1978 Industrial luminaire with (13) 2086:1993 Specification for carriers and
metal reflectors (first bases used in rewirable type 1....
revision) electric fuses for voltages
2206 Flameproof electric lighting upto 650 V (third revision) i
>
fittings: 13703 LV fuses for voltages not
(Part 1): 1984 Well-glass and bulkhead (Part 1): 1993 exceeding 1 000 V ac or
types @-st revision) 1500 dc : Part 1 General
(Part 2) :1976 Fittings using glass tubes requirements
3287:1965 Industrial lighting fittings (14) 2672:1966 Code of practice for library
with plastic reflectors lighting
3528:1966 Waterproof electric lighting 4347:1967 Code of practice for hospital
fittings lighting
3553:1966 Specification for watertight 6665:1972 Code of practice for industrial
electric lighting fittings lighting
4012:1967 Specification for dust-proof 8030:1976 Specification for luminaires
electric lighting fittings for hospitals
4013:1967 Dust-tight electric lighting (15) 732:1989 Code of practice for electrical
fittings wiring installations (third
5077:1969 Decorative lighting outfits revision)

10322 (Part 5/ Luminaires: Part 5 Particular (16) 4648:1968 Guide for electrical layout in
Sec 5) :1987 requirements, Section 5 Flood residential buildings
lights (17) 900:1992 Code of practice for
(11) 8828:1996 Electrical accessories — installation and maintenance
Circuit-breakers for over of $nduction motors (second
current protection for revision)
household and similar (18) 2412:1975 Link clips for electrical
installations (second revision) wiring (first revision)
13947 Speciilcation for low-voltage (19) 2667:1988 Fittings for rigid steel
switchgear and controlgear: conduits for electrical wiring
(Part 1): 1993 General rules @st revision)
(Part 2): 1993 Circuit-breakers 3419:1989 Fittings for rigid non-metallic
(Part 3): 1993 Switches, disconnectors, conduits (second revision)
switch disconnectors and fuse 9537 Conduits for electrical
combination units installations:

66 NATIONALBUILDINGCODE OF INDIA
IS No. Title IS No. Title
(Part 1): 1980 General requirements (Part 4): 1977 Go and no-go gauges for G-5
(Part 2): 1981 Rigid steel conduits and G-13 lc-pin caps ($irst
revision)
(Part 3): 1983 Rigid plain conduits of
3323:1980 Bi-pin lampholders for
insulating materials
tubular fluorescent lamps
14772:2000 Specification for accessories @rst revision)
for household and similar
3324:1982 Holders for starters for
fixed electrical installations
tubular fluorescent lamps
(20) 1913 General and safety (first revision)
(Part 1): 1978 requirements for luminaires:
9900 Basic environmental testing
Part 1 Tubular fluorescent procedures for electronic
lamps (second revision)
and electrical items:
(21) 1258:1987 Bayonet lamp holders (third (Part 1): 1981 General
revision)
(Part 2): 1981 Cold test
(22) 418:1978 Tungsten filament general
(Part 3): 1981 Dry heat test
service electric lamps (third
(Part 4): 1981 Damp test (steady state)
revision)
(23) 374:1979 Electric ceiling type fans and
1534 Ballasts for fluorescent
regulators (third revision)
(Part 1): 1977 lamps: Part 1 For switch start
circuits (second revision) (24) 3043:1987 Code of practice for earthing

1569:1976 Capacitors for use in tubular (25) 8623 Specification for low-voltage
fluorescent high pressure (Part 1): 1993 switchgear and controlgear
mercury and low pressure assemblies: Part 1
sodium vapour discharge Requirements for type-tested
and partially type-test$d
lamp circuit (first revision)
assemblies (jirst revision)
2215:1983 Specification for starters for
(26) 10028 Code of practice for selection,
fluorescent lamps (third
(Part 2): 1981 installation and maintenance
revision)
of transformers: Part 2
2418 Specification for tubular Installation
fluorescent lamps for general
11353:1985 Guide for uniform system of
lighting service:
marking and identification of
(Part 1): 1977 Requirements and tests @-st conductors and apparatus
revision) terminals
(Part 2): 1977 Standard lamp data sheets (27) 2309:1989 Code of practice for the
(jirst revision) protection of buildings and
(Part 3): 1977 Dimensions of G-5 and G-13 allied structures against
lc-pin caps tjirst revision) lightning (second revision)

PART 8 BUILDINGSERVICES— SECTION 2 ELECTRICAL ANDALLIED INSTALLATIONS 67


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES
Section 3 Air Conditioning, Heating and Mechanical Ventilation

BUREAU OF INDIAN STANDARDS


r-

CONTENTS

FOREWORD . .. 3

1 SCOPE ... 5
2 TERMINOLOGY ... 5
3 PLANNING DESIGN CRITERIA .,. 7
4 DESIGN OF AIR CONDITIONING ... 12
5 NOISE AND VIBRATION CONTROL ... 26
6 MECHANICAL VENTILATION (FOR NON AIR CONDITIONED AREAS) ... 30
AND EVAPORATIVE COOLING
7 UNITARY AIR CONDITIONER . .. 35
8 SPLIT AIR CONDITIONER ... 36
9 PACKAGED AIR CONDITIONER ... 37
10 HEATING . .. 38
11 SYMBOLS, UNITS, COLOUR CODE AND IDENTIFICATION OF SERVICES ... 39
12 ENERGY CONSERVATION, ENERGY MANAGEMENT, AUTOMATIC . .. 40
CONTROLS AND BUILDING MANAGEMENT SYSTEM
13 INSPECTION, COMMISSIONING AND TESTING ... 46

LIST OF STANDARDS ... 48

NATIONALBUILDINGCODEOFINDIA
National Building Code Sectional Committee, CED 46

FOREWORD

This Section deals with various aspects of installation of air conditioning equipments and systems in buildings.
The aspects covered include design goals and criteria, design of systems, performance requirements, available
system options, pre-planning requirements, noise and vibration, .&ety aspects, energy conservation and
management, building management systems and inspection, installation, testing and commissioning requirements.

Though all aspects of the air conditioning, heating and mechanical ventilation plant have been touched upon in
this revision, care has been taken right through to look at them from the specific point of view of how they can
be fashioned to impact beneficially on the building as a whole. Thus, topics like pre-planning, safety requirements,
adequate provisions for maintenance, energy management, conservation strategies and noise pollution
considerations have qualified for special attention.

Space requirements for various air conditioning systems vary considerably with the system adopted. In the
scenario of ever-increasing available system options, it has become all the more necessary to consult an air
conditioning engineer in this connection at”the stage of pre-planning.

Weather data has now been included for as many as 58 stations based on data obtained from India Meteorological
Department, Government of India. Till such information is collected for other cities, it is recommended that
design work in these cities maybe carried out according to the present (local) practice.

The first version of this Part was prepared in 1970 which was subsequently revised in 1983. As a result of
experience gained in implementation of 1983 version of this Section and feedback received, a need to revise this
Part was felt.

This revision has therefore been prepared. The significant modifications made in this revision include the following:

a) Definitions of several new terms like ozone depletion potential, global warming potential, indoor air
quality, sick building syndrome, buildings related illnesses and thermal energy storage have been included.
b) A new clause on design criterion has been incorporated.
c) ‘Indoor air quality’ has been included as one of the factors that need to be controlled in the conditioned
space.
d) For large and multi-storeyed buildings, independent air handling unit rooms have been recommended
for each floor.
e) Inside design conditions for various applications have been included; they replace earlier Table 2 and
Table 3.
f) The text on minimum outside fresh air has been revised in the light of cumently accepted international
norms. Recommended values for outside air requirements for ventilation purposes have been furnished
for a wider variety and a larger number of applications.
g) New details have been added on temperature, humidity, and vibration and rioise.
h) Application considerations, covering a wide variety of commercial applications, offices, hotels,
restaurants, computer rooms, etc, have now been given in more details.
j) A new clause on statutory regulation/safety considerations has now been included.
k) Under the clause on design considerations, various system options available have been described.
m) The characteristics and application of options available in piping, water distribution systems and piping
layout have been given prominently.
n) The text on air filters has been revised; focus is now on the approach to filtration in preference to a
detailed description of ever increasingly available option of filter types.
p) The clause on energy conservation and energy management has been thoroughly revised. The concepts
like energy targets, demand targets and consumption targets; the factors to be considered in system

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 3


design that influence energy aspects; the need for analysis of operation of systems during various seasons
of the year, and the need to incorporate energy recovery strategies have been incorporated in this clause.
q) ‘Automatic Controls’ given in the 1983 version has now been replaced by Building Management System,
which addresses not only the control function, but also has a telling impact on operation and maintenance
as well, most importantly on the opportunities afforded to implement various energy conservation
strategies.
r) The text on packaged air conditioners and room air conditioners has been revised and elaborated.
s) The text on heating has been completely revised.
t) The text had been thoroughly revised and additional details have been included under Symbols, Units,
Colour Code and Identification of Services; Pipe Work Services; Duct Work Services; Valve Labels
and Charts; and Inspection, Commissioning and Testing.
u) List of various parameters to be checked for performance of air handling unit, hydronic system balancing,
and finally, the hand-over procedure, have been given.

This revision aims to make a difference in the quality of environment and in building usage, in response to
growing concerns and expectations in with regard to indoor air quality, energy conservation, environmental
impact and building safety.

The provisions on natural ventilation are given in Part 8 ‘Building Services, Section 1 Lighting and Ventilation’.

The provisions of this Section are without prejudice to the various Acts, Rules and Regulations including the
Factories Act, 1948 and the rules and regulations framed thereunder.

The information contained in this Section is based largely on the following Indian Standards:

IS No. Tide
659:1964 Safety code for air conditioning (revised)
1391 Specification for room air conditioners:
(Part 1): 1992 Unitary air conditioners (second revision)
(Part 2) :1992 Split air conditioners (second revision)
2379:1990 Colour code for identification of pipelines (first revision)
3315:1994 Specification for evaporative air coolers (desert coolers) (second revision)
7896:2001 Data for outside design conditions for air conditioning for Indian cities @rst revision)
8148:2003 Specification for packaged air conditioners (jirst revision)

Assistance has also been derived from the following publications in preparation of this Section:

BS 5720:1979 Code of practice for mechanical ventilation and air conditioning in building
Guidelines, Standards and Handbooks of American Society of Heating Refrigerating and Air Conditioning
Engineers
Handbooks of Indian Society of Heating, Refrigerating and Air Conditioning Engineers

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate @e possibility of applying
the most recent editions of the standards.
.

4 NATIONALBUILDINGCODEOF INDIA
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES
Section 3 Air Conditioning, Heating and Mechanical Ventilation

1 SCOPE 2.6 Duct System — A continuous passageway for the


transmission of air which, in addition to the ducts, may
This Section covers the design, construction and
include duct fittings, dampers, plenums, and grilles and
installation of air conditioning and heating systems and
diffusers.
equipment installed in buildings for the purpose
of providing and maintaining conditions of air 2.7 Enthalpy — A thermal property indicating the
temperature, humidity, purity and distribution suitable quantity of heat in the air above an arbitrary datum, in
for the use and occupancy of the space. kilo Joules per kg of dry air (or in Btu per pound of
dry air).
2 TERMINOLOGY
2.8 Evaporative Air Cooling — The evaporative air
2.0 For the purpose of this Section the following cooling application is the simultaneous removal of
definitions shall apply. sensible heat and the addition of moisture to the air.
2.1 Air Conditioning — The process of treating air so The water temperature remains essentially constant at
as to control simultaneously its temperature, humidity, the wet-bulb temperature of the air.
purity, distribution and air movement and pressure to 2.9 Fire Damper — A closure which consists of a
meet the requirements of the conditioned space. normally held open damper installed in an air ---
2.2 Atmospheric Pressure — The weight of air distribution system or in a wall or floor assembly and
column on unit surface area of earth by atmospheric designed to close automatically in the event of a fme
column. At sea level, the standard atmospheric or in order to maintain the integrity of the fire separation.
barometric pressure is 760 mm of mercury (1 033 mm 2.10 Fire Separation Wail — The wall providing
of water column/101.325 Wa). complete separation of one building from another or
Generally atmospheric pressure is used as a datum for part of a building from another part of the same
indicating the system pressures in air conditioning and building to prevent any communication of f~e or heat
accordingly, pressures are mentioned above the tr~smission to wall itself which may cause or assist
atmospheric pressure or below the atmospheric pressure in the combustion of materials of the side opposite to
considering the atmospheric pressure to be zero. A ‘U’ that portion which may be on fue.
tube manometer will indicate zero pressure when 2.11 Global Warming Potential (GWP) — The
pressure measured is equal to atmospheric pressure. potential of a refrigerant to contribute to global
2.3 Buildings Related Illnesses (BRI) — The illness warming.
attributed directly to the specific air-borne building Global warming can make our planet and its climate
contaminants like the outbreak of the Legionnaire’s less hospitable and more hostile to human life, thus
disease after a convention and sensitivity pneumonitis necessitating reduction in emission of green house
with prolonged exposure to the indoor environment gases such as COZ, SOX, NO, and refrigerants. Long
of the building. atmospheric life time of refrigerants results in global
Some of the other symptoms relating to BRI are warming unless the emissions are controlled.
sensory irritation of eyes, ears and throat, skin irritation, GWP values of some of the refrigerants are given
headache, nausea, drowsiness, asthma like symptoms below:
in non-asthmatic persons. The economic consequences
of BRI is decreased productivity, absenteeism and the S1 No. Refrigerant GWP Values
legal implications if occupants IAQ complaints are left
(1) (2) (3)
unresolved.
i) R-12 10600
2.4 Dewpoint Temperature — The temperature at ii) R-22 1900
which condensation of moisture begins when the air is iii) R-134a 1600
cooled at same pressure. iv) R-123 120
v) R-407c 1980
2.5 Dry-Bulb Temperature — The temperature of
vi) R-407a 2340
the air, read on a thermometer, taken in such a way as
vii) R-410a 2340
to avoid errors due to radiation.

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 5


The values indicated above are for an integration period comfort. It also includes methods of controlling thermal
of 100 years. properties of moist air.

2.12 Hydronic Systems — The water systems that 2.19 Psychometric Chart — A chart graphically
convey heat to or from a conditioned space or process representing the thermodynamic properties of moist
with hot or chilled water. The water flows through air.
piping that connects a chiller or the water heater to 2.20 Recirculated Air — The return air that has been
suitable terminal heat transfer units located at the space passed through the conditioning apparatus before being
or process. re-supplied to the space.
2.13 Indoor Air Quality (IAQ) — Air quality that 2.21 Refrigerant — The fluid used for heat transfer
refers to the nature of conditioned air that circulates in a refrigerating system, which absorbs heat at a low
throughout the spacelarea where one works or lives, temperature and low pressure of the fluid Ad rejects
that is, the air one breathes when indoors. heat at a higher temperature and higher pressure of
It not only refers to comfort which is affected by the fluid, usually involving changes of, state of the
temperature, humidity, air movement and odours but fluid.
also to harmful biological contaminants and chemicals 2.22 Relative Humidity — Ratio of the partial
present in the conditioned space. Poor IAQ may be pressure of actual water vapour in the air as compared
serious health hazard. Carbon dioxide has been to the partial pressure of maximum amount of water
recognized as the surrogate ventilation index. that may be contained at its dry bulb temperature.
2.14 Infiltration/Exfiltration — The phenomenon When the air is saturated, dry-bulb, wet-bulb and
of outside air leaking into/out of an air conditioned dewpoint temperatures are all equal, and the relative b —.

space. humidity is 100 percent.


2.15 Ozone Depletion Potential (ODP) — The 2.23 Return Air — The air that is collected from the
potential of refrigerant or gases to deplete the ozone conditioned space and returned to the conditioning
in the atmosphere. equipment.
The ODP values for various refrigerants are as given 2.24 Shade Factor — The ratio of instantaneous heat
below: gain through the fenestration with shading device to
that through the fenestration.
R-n 1.000
2.25 Sick Building Syndrome (SBS) — A term,
R-12 0.820
which is used to describe the presence of acute non-
R-22 0.050
specific symptoms in the majority of people caused
R-123 0.012
by working in buildings with an adverse indoor
R-134a 0.000
environment. It could be a cluster of complex irritative
R-407a 0.000
symptoms like irritation of the eyes, blockened nose
R-407c 0.000
and throat, headaches, dizziness, lethargy, fatigue
R-410a 0.000
irritation, wheezing, sinusitis, congestion, skin rash,
sensory discomfort from odours, nausea, etc. These
Due to highODPofR-11, R- 12 and R-22, their use in
symptoms are usually short-lived and experienced
the air conditioning and refrigeration is being phased-
immediately after exposure; and may disappear when
out. R-123 is also in the phase-out category of
one leaves the building.
refrigerants.
SBS is suspected when significant number of people
2.16 Plenum — An air compartment or chamber to
spending extended tiqe in a building report or
which one or more ducts are connected and which
experience acute on-site discomfort. The economic
forms part of an air distribution system.
consequences of SBS, like BRI, are decreased
The pressure drop and air velocities in the plenum productivity, absenteeism and the legal implications
should be low. Generally, the velocity in plenum should if occupants IAQ complaints are left unresolved.
not exceed 1.5 n-h to 2.5 m/s.
2.26 Smoke Damper — A damper similar to fire
2.17 Positive Ventilation — The supply of outside damper, however, having provisions to close
air by means of a mechanical device, such as a fan. automatically on sensing presence of smoke in air
distribution system or in conditioned space.
2.18 Psychrometry — The science involving
thermodynamic properties of moist air and the effect 2.27 Static Pressure — The pressure that is required
of atmospheric moisture on materials and human to be created by the fan over the atmospheric pressure

6 NATIONALBUILDINGCODE OF INDIA
to overcome the system resistances such as resistances Temporary hardness is primarily responsible for scale
in ducts, elbows, filters, dampers, heating/cooling coils, formation, which results in poor heat transfer resulting
etc. in increased cost of energy for refrigeration and air
conditioning. Permanent hardness (non-carbonate) is
Static pressure is measured by a U tube manometer
not as serious a factor in water conditioning because it
relative to the atmospheric pressure, which is
has a volubility which is approximately 70 times greater
considered as zero pressure. In exhaust systems, fan
than the carbonate hardness. In many cases, water may
produces negative static pressure, which is again used
contain as much as 1 200 ppm of non-carbonate
to overcome the system resistances.
hardness and not deposit a calcium sulfate scale.
2.28 Supply Air — The air that has been passed
The treated water where hardness as ppm of CaC03 is
through the conditioning apparatus and taken through
reduced to 50 ppm or below, is recommenced for air
the duct system and distributed in the conditioned
conditioning applications.
space.
pH is a measure of acidity,pH is a negative logarithm
2.29 Supply and Return Air Grilles and Diffusers
base 10, of the concentration of hydrogen ion in grams
— Grilles and diffusers are the devices fixed in the air
per litre. Water having a pH of 7.0 is neutral, a pH
conditioned space for distribution of conditioned
value less than 7 is acidic and pH value greater than 7
supply air and return of air collected from the
is alkaline. Water with pH less than 5 is quite acidic
conditioned space for re-circulation.
and corrosive to ordinary metals and needs to be
2.30 Thermal Transmittance — Thermal transmission treated.
per unit time through unit area of the given building
2.34 Wet-Bulb Temperature — The temperature
unit divided by the temperature difference between the
registered by a thermometer whose bulb is covered by
air or some other fluid on either side of the building
a wetted wick and exposed to a current of rapidly
unit in ‘steady state’ conditions.
moving air of velocity not less than 4.5 m/s.
2.31 Thermal Energy Storage — Storage of thermal
Wet-bulb temperature is indicated by a wet bulb
energy, sensible, latent or combination thereof for use
psychrometer constructed and used according to
in central system for air conditioning or refrigeration.
specifications.
It uses a primary source of refrigeration for cooling
and storing thermal energy for reuse at peak demand 3 PLANNING DESIGN CRITERIA
or for backup as planned.
3.1 Fundamental Requirements
2.32 Water Conditioning — The treatment of water
circulating in a hydronic system, to make it suitable 3.1.1 The object of installing ventilation and air
for air conditioning system due to its effect on the conditioning facilities in buildings shall be to provide
economics of air conditioning plant. conditions under which people can live in comfort,
work safely and efficiently.
Untreated water used in air conditioning system may
create problems such as scale formation, corrosion and 3.1.2 Ventilation and air conditioning installation shall
organic growth. Appraisal of the water supply source aim at controlling and optimizing following factors in
including chemical analysis and determination of the building:
composition of dissolved solids is necessary to devise a) Air purity and filtration,
a proper water-conditioning programme. b) Air movement,
2.33 Water Hardness — Hardness in water represented c) Dry-bulb temperature,
by the sum of calcium and magnesium salts in water, d) Relative humidity,
which may also include aluminium, iron, manganese, e) Noise and vibration,
zinc, etc. A chemical analysis of water sample should
f) Energy efficiency, and
provide number of total dissolved solids (TDS) in a
g) Fire safety.
water sample in parts per million (ppm) as also
composition of each of the salts in parts per million. 3.1.3 All plans, specifications and data for air
conditioning, heating and mechanical ventilation
Temporary hardness is attributed to carbonates and bi-
systems of all buildings and serving all occupancies
carbonates of calcium and/or magnesium expressed in
within the scope of the Code shall be supplied to the
pafis per million (ppm) as CaC03. The remainder of
Authority, where called for see Part 2 ‘Administration’.
the hardness is known as permanent hardness, which
is due to sulphates, chloride, nitrites of calcium and/or 3.1.4 The plans for air conditioning, heating and
magnesium expressed in ppm as CaC03, mechanical ventilation systems shall include all

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 7


details and data necessary for review of installation g) Internal Load — Lighting and other heat
such as: generating sources like computers, equipment
and machinery; and
a) building: name, type and location;
h) Hours of use.
b) owner: name;
c) orientation: north direction on plans; 3.2.1.2 The design of system and its associated i
d) controls shall also take into account the following:
general plans: dimensions and height of all
rooms; a) Nature of application,
e) intended use of all rooms; b) Type of construction of building,
f) detail or description of wall construction, c) Permissible control limits,
including insulation and finish; d) Control methods for minimizing use of
g) detail or description of roof, ceiling and floor primary energy,
construction, including insulation and finish; e) Opportunities for heat recovery,
h) detail or description of windows and outside Energy efficiency,
f)
doors, including sizes, weather stripping,
g) Filtration standard,
storm sash, sills, storm doors, etc;
h) Hours of use,
j) internal equipment load, such as number of
people, motor, heaters and lighting load; j) Diversity factor, and
k) Outdoor air quality.
k) layout showing the location, size and
construction of the cooling tower (apparatus), 3.2.1.3 The operation of system in the following
.-.
ducts, distribution system; conditions should be considered when assessing the
m) information regarding location, sizes and complete design:
capacity of air distribution system, refrigeration
a) Summer,
and heating plant, air handling equipment;
b) Monsoon,
n) information on air and water flow rates;
c) Winter,
P) information regarding location and
d) Intermediate seasons,
accessibility y of shafts;
e) Night, and
q) information regarding type and location of
dampers used in air conditioning system; f) Weekends and holidays,
r) chimney or gas vent size, shape and height; 3.2.1.4 Consideration should be given to changes in
s) location and grade of the required fire building load and the system designed so that
separations; maximum operational efficiency is maintained.
t) water softening arrangement; and 3.2.1.5 Special applications like hospitals/operating
u) information on presence of any chemical theatres, computer rooms, clean rooms, laboratories,
fumes or gases. libraries, museums/art galleries, sound recording
3.2 Pre-planning studios, shopping malls, etc shall be handled
differently.
3.2.1 Design Considerations
3.2.2 Planning of Equipment Room for Central Air
3.2.1.1 Cooling load estimate shall be carried out prior Conditioning Plant
to installing air conditioning equipment. Calculation
of cooling load shall take into account the following 3.2.2.1 In selecting the location for plant room, the
factors: aspects of efficiency, ec~nomy and good practice
should be considered an&wherever possible it shall
a) Recommended indoor temperature and be made contiguous with the building. This room shall
relative humidity; be located as centrally as possible with respect to the
b) Outside design conditions as specified in 4.4; area to be air conditioned and shall be free from
c) Details of construction and orientation of obstructing columns.
exposures like roof, floor, walls, partition and
In the case of large installations (500 TR and above),
ceiling;
it is advisable to have a separate isolated equipment
d) Fenestration area and shading factors; room where possible. The clear headroom below soffit
e) Occupancy — Number of people and their of beam should be minimum 4.5 m for centrifugal
activity; plants, and minimum 3.6 m for reciprocating and screw
f) Ventilation — Requirement for fresh air; type plants.

8 NATIONALBUILDINGCODEOF INDIA
3.2.2.2 The floors of the equipment rooms should be system options shall be considered and approach
light coloured and finished smooth. For floor loading, ladders for manholes provided.
the air conditioning engineer should be consulted (see
Buried installation shall take into account loads due to
also Part 6 ‘Structural Design, Section 1 Loads, Forces
movement above, of vehicles, etc.
. and Effects’ ).
Provision for adequate expansion tank and its
3.2.2.3 Supporting of pipe within plant room spaces
connection to thermal storage tanks shall be made.
should be normally from the floor. However, outside
plant room areas, structural provisions shall be made 3.2.3 Planning Equipment Room for Air Handling
for supporting the water pipes from the floor/ceiling Units and Package Units
slabs. All floor and ceiling supports shall be isolated
3.2.3.1 This shall be located as centrally as possible
from the structure to prevent transmission of
to the conditioned area and contiguous to the corridors
vibrations.
or other spaces for carrying air ducts. For floor loading,
3.2.2.4 Equipment rooms, wherever necessary, shall air conditioning engineer shall be consulted (see also
have provision for mechanical ventilation. In hot Part 6 ‘Structural Design, Section 1 Loads, Forces and
climate, evaporative air-cooling may also be Effects’).
considered.
3.2.3.2 In the case of large and multistoried buildings,
3.2.2.5 Plant machinery in the plant room shall be independent air handling unit should be provided for
placed on plairdreinforced cement concrete foundation each floor. The area to be served by the air-handling
anti provided with anti-vibratory supports. All unit should be decided depending upon the provision
foundations should be protected from damage by of fire protection measures adopted. Air handling unit
providing epoxy coated angle nosing. Seismic rooms should preferably be located vertically one
restraints requirement may also be considered. above the other.
3.2.2.6 Equipment room should preferably be located 3.2.3.3 Provision should be made for the entry of fresh
adjacent to external wall to facilitate equipment air. The fresh air intake shall have louvers having rain
movement and ventilation. protection profile, with volume control damper and
bird screen.
3.2.2.7 Wherever necessary, acoustic treatment should
be provided in plant room space to prevent noise 3.2.3.4 In all cases air intakes shall be so located as to
transmission to adjacent occupied areas. avoid contamination from exhaust outlets or to the
sources in concentrations greater than normal in the
3.2.2.8 Air conditioning plant room should preferably
locality in which the building is located.
be located close to main electrical panel of the building
in order to avoid large cable lengths. 3.2.3.5 Exterior openings for outdoor air intakes and
exhaust outlets shall preferably be shielded from
3.2.2.9 In case air conditioning plant room is located
weather and insects.
in basement, equipment movement route shall
be planned to facilitate future replacement and 3.2.3.6 No air from any dwelling unit shall be
maintenance. Service ramps or hatch in ground floor circulated directly or indirectly to any other dwelling
slab should be provided in such cases. unit, public corridor or public stairway.
3.2.2.10 Floor drain channels or dedicated drainpipes 3.2.3.7 All air handling rooms should preferably have
in slope shall be provided within plant room space for floor drains and water supply. The trap in floor drain
effective disposal of waste water. Fresh water shall provide a water seal between the air conditioned
connection may also be provided in the air conditioning space and the drain line.
plant room.
3.2.3.8 Supply/return air duct shall not be taken
3.2.2.11 Thermal energy storage through emergency fiie staircase. However, exception
In case of central plants, designed with thermal energy can be considered if fire isolation of ducts at wall
storage its location shall be decided in consultation with crossings is carried out.
the air conditioning engineer. The system may be located 3.2.3.9 Waterproofing of air handling unit rooms shall
in plant room, on rooftop, in open space near plant room be carried out to prevent damage to floor below.
or buried in open space near plant room.
3.2.3.10 The floor should be light coloured, smooth
For roof top installations, structural provision shall take
finished with terrazzo tiles or the equivalent. Suitable
into account load coming due to the same.
floor loading should also be provided after consulting
For open area surface installation horizontal or vertical with the air conditioning engineer.

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 9


3.2.3.11 Where necessary, structural design should Collars for grilles and diffusers shall be taken out only
avoid beam obstruction to the passage of supply and after false ceilinglboxing framework is done and
return air ducts. Adequate ceiling space should be frames for fixing grilles and diffusers have been
made available outside the air handling unit room installed.
to permit installation of supply and return air ducts
3.2.5.3 Where a duct penetrates the masonry wall it
and fire dampers at air handling unit room wall
shall either be suitably covered on the outside to isolate
crossings.
it from masonry, or an air gap shall be left around it to
3.2.3.12 The air handling unit rooms may be prevent vibration transmission. Further, where a duct
acoustically treated, if located in close proximity to passes through a fwe resisting compartmenthrrier, the
occupied areas. annular space shall be sealed with fire sealant to prevent
smoke transmission (see also Part 4 ‘Fire and Life
3.2.3.13 Access door to air handling unit room shall
Safety’).
be single/double leaf type, airtight, opening outwards
and should have a sill to prevent flooding of adjacent 3.2.6 Cooling Tower
occupied areas. It is desired that access doors in air
3.2.6.1 Cooling towers are used to dissipate heat from
conditioned spaces should be provided with tight
water cooled refrigeration, air conditioning and
sealing, gaskets and self closing devices for air
industrial process systems. Cooling is achieved by
conditioning to be effective.
evaporating a small proportion of recirculating water
3.2.3.14 It should be possible to isolate the air handling into outdoor air stream. Cooling towers are installed
unit room in case of fire. The door shall be fire resistant at a place where free flow of atmospheric air is
and fire/smoke dampers shall be provided in supply/ available.
return air duct at air handling unit room wall crossings
3.2.6.2 Range of a cooling tower is defined as
and the annular space between the duct and the wall
temperature difference between the entering and
should be fire-sealed using appropriate fire resistance
leaving water. Approach of the cooling tower is the
rated material.
difference between leaving water temperature and the
3.2.3.15 For buildings with large structural glazing entering air wet bulb temperature.
areas, care should be taken for providing fresh air
3.2.6.3 Types of cooling tower
intakes in air handling unit rooms. Fire isolation shall
be provided for vertical fresh air duct, connecting 3.2.6.3.1 Natural drafi
several air handling units.
This type of tower is larger than mechanical draft tower
3.2.4 Planning of Pipe Shafts as it relies on natural convection to obtain the air
circulation. A natural draft tower needs to be tall to
3.2.4.1 The shafts carrying chilled water pipes should
obtain the maximum chimney effect or rely on the
be located adjacent to air handling unit room or within
natural wind currents.
the room.
3.2.6.3.2 Mechanical drajl
3.2.4.2 Shaft carrying condensing water pipes to
cooling towers located on terrace should be vertically The fans on mechanical draft towers may be on the
aligned. inlet air side (forced draft) or exit air side (induced
draft). Typically, these have centrifugal or propeller
3.2.4.3 All shafts shall be provided with fire barrier
type fans, depending on pressure drop in tower,
at floor crossings (see Part 4 ‘Fire and Life Safety’).
permissible sound levels andenergy usage requirement.
3.2.4.4 Access to shaft shall be provided at every On the basis of direction of air and water flow,
floor. mechanical draft cooling towers can be counter flow
or cross flow type.
3.2.5 Planning for Supply Air Ducts and Return
Air 3.2.6.4 Factors to be considered for cooling tower
selection are:
3.2.5.1 Duct supports, preferably in the form of angles
of mild steel supported using stud anchors shall be a) Design wet-bulb temperature and approach
provided on the ceiling slab from the drilled hole. of cooling tower.
Alternately, duct supports may be fixed with internally b) Height limitation and aesthetic requirement.
threaded anchor fastners and threaded rods without c) Location of cooling tower considering
damaging the slabs or structural members. possibility of easy drain back from the
3.2.5.2 If false ceiling is provided, the supports for system.
the duct and the false ceiling, shall be independent. d) Placement with regard to adjacent walls and

10 NATIONALBUILDINGCODE OF INDIA
windows, other buildings and effects of any formation, chemicals may be added to inhibit corrosion
water carried over by the air stream. and limit microbiological growth.
e) Noise levels, particularly during silent hours Provision shall be made to make-up for the loss of
and vibration control. circulating water.
f-) Material of construction for the tower.
3.2.6.10 Provision for make-up water tank to the
d Direction and flow of wind. cooling tower shall be made. Make-up water tank to
h) Quality of water used for make-up. the cooling tower shall be separate from the tank
j) Maintenance and service space. serving drinking water.
k) Ambient air quality.
3.2.6.11 Make-up water having contaminants or
3.2.6.5 The recommended floor mea requirement for hardness, which can adversely affect the refrigeration
various types of cooling tower is as given below: plant life, shall be treated.

a) Natural draft cooling 0.15 to 0.20 m2/t 3.2.6.12 Cooling tower should be so located as to
tower of refrigeration eliminate nuisance from drift to adjoining structures.
b) Induced draft cooling 0.10 to 0.13 m2/t 3.2.7 Glazing
tower of refrigeration
c) Fibre-reinforced 0.07 to 0.08 m2/t 3.2.7.1 Glazing contributes significantly to heat
plastic of refrigeration addition in air conditioned space; measures shall,
therefore, be adopted to minimize the gain.
3.2.6.6 Any obstruction to free flow of air to the
3.2.7.2 While considering orientation of the building,
cooling tower shall be avoided.
(see Part 8 ‘Building Services, Section 1 Lighting and
3.2.6.7 Structural provision for the cooling tower shall Ventilation’) glazing in walls subjected to heavy sun
be taken into account while designing the building, exposure shall be avoided. In case it is not possible to
Vibration isolation shall bean important consideration do so, double glazing or heat resistant glass should be
in structural design. used. Glazing tilted inward at about 12° also helps
curtail transmission of direct solar radiation through
3.2.6.8 Special design requirements are necessary
the glazing.
where noise to the adjoining building is to be
avoided. 3.2.7.3 Where sun breakers are used, the following
aspects shall be kept in view:
3.2.6.9 As given below, certain amount of water is
lost from circulating water in the cooling tower: a) The sun breakers shall shade the maximum
glazed area possible, specially from the
a) Evaporation loss — In a cooling tower, the
altitude and azimuth angle of the sun, which
water is cooled by evaporating a part of the is likely to govern the heat load.
circulating water into the air stream. The
b) The sun breakers shall preferably be light and
amount of circulating water so evaporated
bright in colour so as to reflect back as much
is called ‘evaporation loss’. Usually it
of the sunlight as possible.
is about 1 percent of the rate of water
circulation. c) The sun breakers shall preferably be 1 m away
from the wall face, with free ventilation,
b) Drift loss — A small part of circulating water
particularly from top to bottom and are meant
is lost from the cooling tower as liquid
for carrying away the heat which is likely to
droplets entrained in the exhaust air stream.
get boxed between the sun breakers and the
Usually the drift loss is 0.1 percent to 0.2
main building face.
percent of rate of water circulation.
d) The sun breakers shall be installed as to have
c) Blow-dowrvbleed-off— To avoid concentration
minimum conduction of heat from sun
of impurities contained in the water beyond
breakers to the main building.
a certain limit, a small percentage of water
in the cooling water system is often 3.2.7.4 Where resort is taken to provide reflecting
purposely drained off or discarded. Such a surfaces for keeping out the heat load, care should
treatment is called ‘blow-down’ or ‘bleed- be taken regarding the hazards to the traffic and
off’. The amount of blow-down is usually people on the road from the reflected light from the
0.8 percent to 1 percent of the total water surfaces.
circulation.
3.2.7.5 Day light transmittance for various type of
If simple blow-down is inadequate to control scale glass is given in Table 1.

PART8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 11


Table 1 Day Light Transmittance for Various air from as clean an area as possible. If low level intakes
Types of Glass are used, care should be taken to position them well
away from roadways and car parks.
S1 Type ofGlass VkibleTransmittance
No. W/(mz“C) 4.2 Design Considerations
(1) (2) (3)
4.2.1 Types of System
i) 3 mm regularsheetor plate glass 0.86 to 0.91
ii) 3 mm grey sheet glass 0.31 to 0.71 Systems for air conditioning need to control temperature
iii) 5 mm grey sheetglass 0.61 and humidity within predetermined limits throughout .
iv) 5.5 mm grey sheetglass 0.14 to 0.56
6 mm grey sheetglass 0.52 the year. Various types of refrigerating systems are
v) 6 mm green/ftoatglass 0.75 available to accomplish the tasks of cooling and
vi) 6 mm greyplate glass 0.44 dehumidifying, which are an essential feature of air
vii) 6 mm bronzeplate glass 0.49
viii) 13mm grey plate glass conditioning. Systems for air conditioning may be
0.21
ix) 13mm bronzeplate glass 0.25 grouped as all-air type, air and water type, all water
x) Coatedglasses(single,laminated, 0.07 to 0.50 type or unitary type.
insulating)
4.2.1.1 All-air system
3.2.8 Roof Insulation
This type of air conditioning system provides
3.2.8.1 Under-deck or over-deck insulation shall be complete sensible and latent cooling, preheating and
provided for exposed roof surface using suitable humidification in the air supplied by the system. Most
insulating materials. Over-deck insulation should be plants operate on the recirculation principle, where a
properly waterproofed to prevent loss of insulating percentage of the air is extracted and the remainder
properties. mixed with incoming fresh air.

3.2.8.2 The overall thermal transmittance from the Low velocity systems may be used. High velocity
exposed roof should be kept as minimum as possible systems although require smaller ducts, are high on
and under normal conditions, the desirable value fan energy, require careful acoustic treatment and
should not exceed 0.58 W/(m* ‘C). higher standards of duct construction.

3.2.8.3 The ceiling surface of floors which are not 4.2.1.1.1 Constant volume system
to be air conditioned may be suitably insulated to
Accurate temperature control is possible, according to
give an overall thermal transmittance not exceeding
the system adopted. Low velocity system variations
1.16 W/(m* “C)
include dehumidification with return air bypass, and
4 DESIGN OF AIR CONDITIONING multi-zone (hot declclcold deck mixing). High velocity
system may be single or dual duct type.
4.1 General
4.2.1.1.2 Variable volume system
A ventilation and air conditioning system installed in
a building should clean, freshen and condition the air Most Indian air conditioning systems operate at partial
within the space to be air conditioned. This can be load for most of the year and the variable air volume
achieved by providing the required amount of fresh (VAV) system is able to reduce energy consumption
air either to remove totally or to dilute odours, fumes, by reducing the supply air volume to the space under
etc (for example, from smoking). Local extract systems low load conditions. Thp VAV system can be applied
may be necessary to remove polluted air from kitchens, to interior or perimeter zones, with common or separate
toilets, etc. Special air filters may be required to remove fans, with common or separate air temperature control.
contaminants or smells when air is recirculated. The greatest energy saying associated with VAV
occurs at the perimeter ztmes, where variation in solar
It is desirable that access doors to air conditioned space
and outside temperature allow tbe supply air quantity
are provided with tight sealing gaskets and self closing
to be reduced. Good temperature control is possible
devices for air conditioning to be effective.
but care should be taken at partial load to ensure
Positions of air inlets and extracts to the system are adequate fresh air supply and satisfactory control of
most important and care should be taken in their air distribution and space humidity.
location. Consideration should be given to relatively
4.2.L2 Air and water system
nearby buildings and any contaminated discharges
from those buildings. Inlets should not be positioned Control of conditions within the space is achieved by
near any flue outlets, dry cleaning or washing machine initial control of the supply air from a central plant but
extraction outlets, kitchen, water-closets, etc. When with main and final control at a terminal unit within.
possible, air inlets should beat high level so as to induce the conditioned space. The supply air provides the

12 NATIONALBUILDING CODE OF INDIA


necessary ventilation air and the small part of the total 4.2.2 Vapour Compression Water Chiller
conditioning. The major part of room load is balanced
These normally contain the complete refrigerating
by water through a coil in the terminal unit, which can
system, comprising the compressor, condenser,
be either a fan coil unit or an induction unit.
expansion device and evaporator together with the
Depending on the degree of control required, the water automatic control panel. The unit can be set down on
circulating system can be either of two, three or four to a solid foundation on resilient mountings. Pipe
pipe arrangement. With two pipe circulation a single connection require flexible couplings; these should be
flow and a single return circulate chilled or hot water considered in conjunction with the design of the pump
as required. Such a system can only provide heating mountings and the pipe supports.
or cooling to the system on a changeover basis, so it is
Capacity control is normally arranged to maintain an
ineffective where wide modulations of conditions over
approximately constant temperature of the chilled
short periods are required. The installed cost however
water leaving the evaporator. This may be adequate
is naturally the lowest of all the circulation systems.
for one or two packages, but a more elaborate central
The three pipe system is a way of overcoming the
control system may be necessary for a large number.
disadvantages of the two pipe system without raising The design of the refrigeration control system should
the installed cost too high. In this system a separate be integrated, or be compatible, with the control system
hot water flow and chilled water flow is taken to the for the heat transfer medium circulated to the air cooler.
terminal units but a common return is taken from these
units to the plant room. The best system from a control It is normal for installation to have several water
point of view is the four pipe system, where separate chilling packages, both to provide for stand-by and
hot water and chilled water supply and returns are taken enable the cooling load to be matched with the
from the plant room to the terminal units. Although minimum consumption of power. Although most
the most expensive method of circulating the water, it packages can reduce capacity to match the cooling
is the only satisfactory one, if reasonable control is demand, the consumption of the power per unit of
required throughout the year. cooling increases; the resulting drop in efficiency is
most serious below one-third capacity.
4.2.L3 All water system
Power consumption can be reduced by taking
In the simplest layout, the fan coil units maybe located advantage of a fall in the ambient temperature, which
against an outside wall with a direct, fresh air permits a corresponding fall in the condensing
connection. A superior arrangement utilizes a ducted, temperature and consequent reduction in the
conditioned, fresh air supply combined with mechanical compressor power. It is important, for economy in the
extract ventilation, operation, that the optimum equipment selection and
Control of unit out put maybe achieved by fan speed design of the control system is achieved.
and water flow/temperature control. Electric power is The classification of the water chilling packages is by
required at each terminal unit. the type of compressor.
Provision of variable volume water flow system for 4.2.2.1 Centrij%gal compressors
chilled water circulation is recommended for varying
These compressors have an impeller that imparts to
load conditions. This may be incorporated with the help
the refrigerant vapour a high kinetic energy, which is
of constant volume primary chilled water circuit and
then transformed into pressure energy. For water
variable flow secondary chilled water circuit having
chilling applications, compressors with one or two
pumps with variable speed drives and pressure sensor
stage of compression are used. Two stage units often
to control the speed. This system allows better control
incorporate an interstate’economizer for improving
on energy consumption under partial load conditions
efficiency.
due to diversity or seasonal load variations.
The compressor can be modulated down to approaching
4.2.1.4 Unitary systems
10 percent of full load capacity, with some control of
Such systems are usually those incorporating one or the condensing pressure. Because of the nature of
more units or packaged air conditioners having a direct compression process, the flow through the compressor
expansion vapour compression refrigeration system. can become unstable if the compressor is called upon
Similar units using chilled water from a central plant to produce a pressure rise in excess of its design limits.
would be designated fan coil systems. Most units are This phenomenon, known as surging, is a serious
only suitable for comfort applications but specially problem but occurs only under a fault condition.
designed units are also available for process and Typical faults are excessive fouling of the condenser,
industrial applications. a partial failure of the condenser coolant flow or an

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 13


accumulation of a non-condensable gas (air) in the conventional oil cooler. Such an arrangement can
condenser. Unchecked surging can lead to damage to impose a small penrdty on the plant capacity.
the compressor or its drive and does increase the noise
The condenser most commonly used on packaged units
level.
is the watercooled shell-and-tube type, but equipment
The use of low pressure refrigeration to suit the with air cooled condensers is also available. The
characteristics of the compressor in the smaller size expansion device used will depend on the evaporator
range, means that the evaporator operates at below type but it is often a electronic expansion valve (single
atmospheric pressure, thus a leak can draw in air and or in multiple) of conventional or modified form.
atmospheric moisture. These should be prevented from
Screw compressors are available in open and serni-
accumulating, since these interfere with the operation
hermetic fonq (see 4.2.2.1) and are generally coupled
of the plant and cause corrosion.
direct to two-pole motors. The capacity of the
The compressors may be driven either directly by compressor can be modulated down to 10 percent of
electric motor or via a speed-increasing gear train. full load capacity.
Units are available in ‘open’ form, that is, compressor
and motor are separate items, or in semi-hermetic form 4.2.2.3 Reciprocating compressors
where the motor and compressor are contained in a These are available in a wide range of sizes and designs.
common pressure-tight casing that is bolted together. They are almost invariably used in packages up to
The latter type eliminates the drive shaft gland seal (a 120 TR cooling capacity.
potential point of leakage), which is necessary on the
former. Because the cylinders have automatic valves, a single
compressor may be used over wide range of operating
Certain types of open centrifugal compressors could conditions with near optimum efficiency, whereas
conveniently be directly driven by a steam or gas other types of compressor require detailed modification
turbine. This arrangement could be advantageous when to give optimum efficiency at different conditions. This
the refrigeration plant forms part of total energy system. is, however, of minor importance for normal air
The centrifugal compressor type water chilling conditioning duties.
packages normally include a shell-and-tube water Capacity control is achieved by making cylinders in-
cooled condenser and a flooded shell-and-tube operative, usually by propping open the suction valves,
evaporator, but unit are also available incorporating thus, capacity reduction is in a series of steps rather
an air cooled condenser The expansion device is than by modulation. Typically, a four-cylinder
commonly an electronic expansion valve or high compressor would be unloaded in four steps. It is
pressure float regulating valve. therefore necessary to allow for this stepwise operation
4.2.2.2 Screw compressors in designing the chilled water temperature control
system.
Two types of screw compressors are available, that
is, single and twin screw, and both are positive The evaporator is normally of the dry expansion type,
displacement machines. Compression of the refrigerant to permit oil from the compressor to circulate round
vapour is achieved by the progressive reduction of the the system with the refrigerant. Shell-and-tube water
volume contained with in the helical flutes of the cooled condensers are common, but any type of
cylindrical rotor(s) as they rotate. condenser can be used. With air cooled condensers it
is normal practice to build the machine package so that
Oil is injected into the rotor chamber for sealing and it may be located on the roof in a package including
lubrication purposes and is removed from the the condenser.
refrigerant discharge gas in an oil separator before the
refrigerant passes onto the condenser. No oil separator It is common for the electric drive motors to be built
is 100 percent efficient and so a small quantity of oil into the compressor assembly; this is known as a ‘semi-
always passes through with the refrigerant. On systems hermetic’ drive to distinguish it from the ‘hermetic’,
using a direct expansion evaporator the oil is trapped in which the compressor and motor are enclosed within
in the evaporator and an oil recovery system is a pressure vessel and cannot therefore be serviced.
necessary. The semi-hermetic compressor is more compact
With some systems oil cooler is required in the oil and is quieter in operation than the ‘open’ drive
circulation system, to remove the heat gathered by the compressor, but involves a more difficult service
oil during compression cycle. On other systems liquid operation in the event of a motor failure. It gains in
refrigerant is injected into the compressor to remove reliability, however, by avoiding the shaft seal of the
the heat of compression instead of using the ‘open’ compressor.

14 NATIONALBUILDING CODE OF INDIA


It is recommended that multiple hermetic or semi- 4.3 System Design
hermetic compressor unit should not be connected to
4.3.1 Ductwork and Air Distribution
a common refrigerant system, as failure of one motor
can precipitate failure of the others. Separate refrigerant 4.3.1.1 Materials
circuits for each compressor should be used.
Ductwork is normally fabricated, erected and finished
4.2.3 Absorption System to the requirements in accordance with accepted
standard [8-3( 1)]. Designers should specify the
The absorption cycle uses a solution that by absorbing
requirements, as appropriate for the velocity and
the refrigerant replaces the function of the compressor.
pressure, and materials to be employed. Ductwork is
The absorbenthefrigerant mixture is then pumped to a
generally manufactured from galvanized steel sheet.
higher pressure where the refrigerant is boiled off by
Ductwork may also be manufactured from aluminium
the application of heat, to be condensed in the
sheet for applications like operation theatres and
condenser.
intensive care units where stringent cleanliness
Absorption machines are mostly used in liquid-chilling standards are a functional requirement. Galvanized
applications, These are most suitable for hotels and steel sheets shall be in accordance with the accepted
hospitals where steam is readily available from the standard [8-3(2)] whereas aluminium sheet shall be in
boilers. accordance with the accepted standard [8-3(3)]. Where
building materials, such as concrete or brick, are used
4.2.3.1 Indirect firing
in the formation of airways, the interior surface should
The lithium bromide/water absorption system can be be fire resistant, smooth, airtight and not liable to
powered by medium or high temperature hot water and erosion.
low or medium pressure steam. Water is the refrigerant
4.3.L2 Ductwork design
and the lithium bromide the absorbent. The four
compartments enclosing the heat exchanger tube Design calculations made to determine the size and
bundles for the condenser, evaporator, generator and configuration of ductwork in respect of pressure drop
absorber can be in a single or multiple pressure vessel and noise generation should conform to standard
arrangement. The whole assembly has to be maintained methods.
under a high vacuum, which is essential for the correct
Ductwork design should also take into account the
functioning of the unit. Water and absorbent solutions
recommendations for fwe protection (see Part 4 ‘Fire
are circulated within the unit by electrically driven
and Life Safety’ ) relating to the design of air handling
pumps.
system to fire and smoke control in buildings.
Capacity control down to 10 percent of full load
4.3.1.3 Luyout consideration
capacity is achieved by modulating the flow of the
heating medium in relation to the cooling demand. When designing ductwork, consideration should be
There is some loss in performance at part load, which given to:
can be compensated by refinements in the system
a) Co-ordination with building, architectural and
design and control.
structural requirements;
4.2.3.2 Direct firing b) Co-ordination with other services;
Direct fired lithium bromide/water absorption plants c) Simplifying installation work;
have become common, by incorporating precise d) Providing facilities and access for
control of generator temperature necessary to avoid commissioning md testing;
crystallization. e) Providing facilities and access for operating
Ammonia/water systems can be and are direct fired, and maintenance;
but are rarely used for water chilling duties except for f) Meeting fire and smoke control requirement;
small sized units, which are installed outside the and
building. There are two reasons or this, firstly capital g) Prevention of vibration and noise transmission
costs are higher and secondly the danger to personnel to the building/space.
in the event of leakage of the refrigerant.
4.3.2 Piping and Water Distribution System
Direct firing has the advantage that the losses in an
4.3.2.1 Materials
indirect heating system are avoided, but in an air
conditioning installation where a boiler system Steel piping with welded or flanged joints is commonly
is installed to provide heating, the advantage is used. Flanges for flanged joints are welded to pipes.
minimal. The choice of materials or any installation will be

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 15


goverued by economic considerations, but care should Main headers in the plant room are designed for very
be taken to minimize the possibility of corrosion when low velocity around 1 mk. Noise can be caused by
choosing material combinations. velocities in excess of 4 nds but this is more likely to
be caused by air left in the pipes by inadequate venting.
4.3.2.2 Design principles
Where materials other than steel are used, erosion can
The system design should achieve the following two occur at the higher velocities particularly if the water
main objectives: is allowed to become acidic.

a) A good distribution of water to the various Friction factor in piping should not exceed 5 m of water
heat exchangers/cooling coils at all conditions for 100 m of pipe length. The power consumed in
of load. This will be influenced by the method circulating the water around the system is proportional
chosen to control the heat transfer capacity to the pressure loss (due to friction) and the flow. It is
of air handling units. Failure to achieve good therefore an advantage to design system with a water
hydraulic design may lead to difficulties with temperature rise say 50C-70C which results in
system balancing. Adequate provision should minimizing the flow rate.
be made for measuring flow rates and pressure
Air-conditioning system operate for a large part of the
differentials.
time at less than the design load, and this means that
b) An economic balance between pipe size and operating costs can be minimized if the water quantity
piping cost. circulated can be reduced at partial load. This should
Excessive water velocities should be avoided, as they be done with variable speed pumping systems.
may lead to noise at pipe junctions and bends. 4.3.2.4 Luyout considerations
When multiple water-chilling packages have to be used The layout of the main pipe runs should be considered
in a large system, the control of the machines and the in relation to the building structure, which will have to
arrangement of the water circulation should be support their weight and carry the imposed axial loads.
considered as an integrated whole. It is not possible to The positioning of expansion joints should be
obtain satisfactory result by considering control and considered in relation to the branches, which may only
system design separately. accommodate small movements. The pumps should
Temperature changes in the system lead to changes in not be subjected to excessive loads from the piping.
the volume of water, which has to be allowed to expand Provision should be made for venting air and any gas
into a suitable expansion tank. It is essential that the formed by corrosion processes from the high points in
point at which the expansion tank is connected into the system: failure to do this can lead to restricted water
the system be such that it is never shutoff. It is normal flows and poor performance.
practice to locate the expansion tank above the highest
point in the system, so that a positive pressure is New systems invariably contain debris of one sort or
maintained when all the pumps are stopped; if this is another left during construction, and this can cause
not possible, a closed tank can be installed at a lower trouble by blocking pipes, control valves and pumps
level and pressurized by an inert gas. Closed expansion if it is not removed during testing and commissioning.
tank with air separator in the chilled water system helps Piping system should be designed to permit proper
in improving the life and efficiency of chilled water cleaning and flushing and should include suitable
piping and heat exchange equipment. strainers at appropriate locations.

For central chilled water air conditioning systems, 4.3.3 Thermal Insulation
water is the usual heat transfer medium use to convey 4.3.3.1 Air conditionirig and water distribution
the heat from the air-handling units to the primary systems carry chilled or heated fluids. Thermal
refrigerant in the evaporator. In certain special cases, insulation is required to prevent undue heat gain or
when temperatures lower than 5°C are required, an loss and also to prevent internal and external
anti-freeze such as ethylene glycol may be added to condensation; a vapour seal is essential if there is a
depress the freezing point. possibility of condensation within the insulating
4.3.2.3 Piping design materials.

The arrangement of the water piping will depend upon 4.3.3.2 The selection of suitable thermal insulating
the cooling or heating systems chosen as being the most materials requires that consideration be given to
suitable for the building. physical characteristics as follows:

The water velocity normally used are dependent on a) Fire Properties — Certain insulating
pipe size but are usually in the range 1 rnls to 3 rids. materials are combustible or may, in a fire,

16 NATIONALBUILDING CODE OF INDIA


produce appreciable quantities of smoke and as specified in this Section in terms of dry-bulb
noxious and toxic fumes. temperature and relative humidity or wet-bulb
b) Materials and their finishes should inherently temperature.
be proof against rotting, mould and fungal 4.4.2 Humidity
growth, and attack by vermin, and should be
non-hydroscopic. 4.4.2.1 Comfort considerations
c) Material should not give rise to objectionable The controlled temperature levels should also be
odour at the temperature at which they are to considered in relation to the humidity of the air. A high
be used. humidity reduces evaporative cooling from the body
d) The material should not cause a known hazard and hence creates the sensation of a higher temperature.
to health during application, while in use, or. Beyond certain’ limits, however, humidity produces
on removal, either from particulate matter or disagreeable sensations.
from toxic fumes.
For normal comfort conditions, relative humidity (RH)
e) It should have a low thermal conductivity values between 40 percent and 70 percent are
throughout the entire working temperature acceptable.
range.
It should be non-flammable and should not 4.4.3 Inside Design Conditions
f)
support nor spread fire. The inside design conditions for some of the
&’) It should have good mechanical strength and applications are indicated in Table 2.
rigidity otherwise it would have to be ~ladded ---
4.4.4 Outside Design Conditions
for protection.
The outside design conditions (dry-bulb and mean
4.4 Design Conditions coincidental wet-bulb) taken shall be in accordance
4.4.1 Temperature with the summary of the conditions given in the
Table 3.
4.4.1.1 General consideration
Values of ambient dry-bulb and wet-bulb temperatures
Certain minimum temperatures may be required against the various annual percentiles represent the
depending on type of application and by local value that is exceeded on average by the indicated
regulations. Maximum permitted cooling temperatures percentage of the total number of hours. The 0.4
may be stipulated by relating to energy conservation. percent, 1.0 percent, 2.0 percent values are exceeded
From the comfort aspect, it is important to take into on average 35,88 and 175 h in a year. The 99.0 percent
account the effect of radiant temperature in fixing the and 99.6 percent values are defined in the same way
desired air temperatures to maintain comfortable but are usually reckoned as the values for which the
conditions. corresponding weather elements are less than the
design conditions for 88 h and 35 h, respectively.
When large windowslcurtain walls are used, it may be
necessary to provide shadinglnorth orientation to Mean coincidental values are the average of the
protect the occupants from solar radiation and to reduce indicated weather element occurring concurrently with
the cooling load on the system. It is not practical to the corresponding design value.
fully compensate for solar heating, owing to its After the calculation of design dry-bulb temperatures,
intermittent nature, simply by lowering air temperature. the programme located the values of corresponding
A person’s heat loss, and hence his feeling of comfort, wet-bulb temperatures from the database for that
depends not only on the air temperature but also on particular station, the average of these values were
the radiant heat gain, the air movement and the computed, which were then called mean of coincidental
humidity of the air. Many attempts have been made to wet-bulb temperature.
devise a single index that combines the effect of two In the same way design wet-bulb temperatures and
or more of these separate variables. In practice the coincidental dry-bulb temperatures were evaluated.
difference between these indices is small, provided the
various parameters do not vary beyond certain limits. Selection: The design values of 0.4 percent, 1.0 percent
and 2.0 percent annual cumulative frequency
4.4.1.2 Design temperatures of occurrence may be selected depending upon
application of air conditioning system.
Itshould be noted that, although comfort conditions
are established in terms of resultant temperature, the For normal comfort jobs values under 1 percent column
design air temperature for air conditioning should be could be used for cooling loads and 99 percent column

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 17


Table 2 Inside Design Conditions for Some Applications
(Clause 4.4.3)

s] Category Inside Design Conditions


No.
Summer Winter
(1) (2) (3) (4)

i) Restaurants DB 23 to 26°C DB 21 to 23°C


RH 55 to 60% RH not less than 40%
ii) Office buildings DB 23 to 26°C DB 21 to 23°C ‘
RH 50 to 60% RH not less than 40%
iii) Radio and television studios DB 23 to 26°C DB 21 to 23°C
RH 45 to 55% RH 40 to 50%
iv) Departmental stores DB 23 to 26°C DB 21 to 23°C
RH 50 to 60% RH not less than 40%
v) Hotel guest rooms DB 23 to 26°C DB 23 to 24°C
RH 50 to 6070 RH not less than 40%
vi) Class rooms DB 23 to 26°C DB 23 to 24°C
RH 50 to 60% RH not less than 40%
vii) Auditoriums DB 23 to 26°C DB 23 to 24°C
RH 50 to 60% RH not less than 40%
viii) Recovery rooms DB 24 to 26°C
RH 45 to 55%
ix) Patient rooms DB 24 to 26°C
RH 45 to 55%
x) Operation theatres DB 17 to 27°C
RH 45 to 55%
xi) Museums and libraries DB 20 to 22°C
RH 40 to 55%
xii) Telephone terminal rooms DB 22 to 26°C
RH 40 to 5070

Table 3 Summary for Outdoor Conditions 4

(Clause 4.4.4)
Station Cooling DB/MCWB Cooling WB/MCDB Heating DB/MCWB
~~~
0.4% 1.0% 2.0% 0.4% 1.0% 2.0% 99.6% 99.0%
~~ ~~ ~ f—’—, ,—’—, f—-—-,
DB MCWB DB MCWB DB MCWB WB MCDB WB MCDB WB MCDB DB MCWB DB MCWB
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17)

42.3 24.1 41.2 23.5 40.0 24.3 28.7 34.3 28.2 33.6 27.8 33.1 11.5 9.0 12.9 9.8
Akola 43.4 24.0 42.2 23.3 41.0 23.6 27.6 37.8 26.7 34.4 26.1 33.5 12.7 10.3 13.9 10.6
Allahabad 43.7 23.4 42.2 23.5 40.8 22.7 28.8 33.0 28.4 32.8 28.0 32.6 7.9 7.0 9.1 8.3
Amritsar 41.6 23.2 40.3 24.6 38.9 24.4 29.3 34.8 28.8 34.8 28.4 33.4 2.7 2.3 4.0 3.5
Aurangabad 40.3 22.1 39.3 22.9 38.3 21.3 26.3 36.2 25.3 33.1 24.7 31.4 10.6 8.2 12.0 9.1
Bangalore 34.7 19.6 34.0 19.6 33.1 19.2 23.5 28.9 22.9 28.2 22.5 27.7 14.9 13.0 15.7 13.8
Banner 43.1 24.2 42.0 23.6 41.0 23.3 28.5 37.9 27.8 35.3 27.2 33.3 9.5 5.1 10.7 5.5
Belgaum 36.5 19.4 35.7 19.6 34.7 19.2 24.3 29.2 23.8 29.5 23.4 28.2 13.2 11.3 14.3 12.2
Bhagalpur 42.4 26.8 40.7 27.4 38.9 25.6 30.0 37.1 29.6 36.4 29.2 35.2 11.4 10.3 12.6 12.4
Bhopal 41.7 22.0 40.5 21.7 39.3 21.3 26.0 31.0 25.6 30.3 25.2 29.9 9.8 6.8 11.0 8.0
Bhubaneshwar 38.9 25.5 37.6 26.6 36.3 26.3 29.4 35.2 28.9 33.3 28.5 32.7 14.4 13.1 15.4 14.0
Bikaner 44.8 22.4 43.4 22.4 42.0 23.1 28.5 34.6 27.9 33.1 27.3 34.7 3.8 2.2 5.3 3.1
Chennai 38.4 26.2 37.3 26.7 36.3 26.4 29.1 33.8 28.6 33.2 28.1 31.9 19.5 20.2 18.7 19.3
Chitradurg 36.6 18.8 35.8 19.0 35.0 19.6 23.9 28.9 23.5 28.2 23.2 28.5 15.4 12.5 16.4 13.3
Dehradun 37.8 23.5 36.3 23.9 34.8 22.8 27.0 31.3 26.5 30.1 26.0 29.8 5.9 5.0 6.8 5.8
Dibrugarh 34.0 27.4 33.2 26.8 32.3 26.7 28.3 32.6 27.8 31.8 27.4 31.3 7.5 7.2 8.7 8.4
Gorakhpur 41.4 26.2 40.3 26.0 39.1 26.4 29.9 35.2 29.7 35.5 29.4 34.7 7.9 7.5 9.0 8.4
Guwahati 34.4 26.9 33.4 27.3 32.7 26.8 28.8 32.4 28.3 31.8 27.9 31.5 10.2 9.8 11.3 10.8

18 NATIONAL BUILDING CODE OF INDIA


Table 3 — Concluded

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17)
Gwalior 43.9 23.0 42.5 22.9 41.3 23.5 27.9 32.9 27.6 32.4 27.3 32.7 4.9 3.8 6.4 5.3
Hissar 44.7 26.5 43.3 25.8 41.7 27.9 30.1 40.2 29.9 39.0 29.4 36.8 5.0 4.2 6.1 5.2
Hyderabad 40.4 22.5 39.2 22.5 38.2 22.4 25.6 33.7 25.2 32.4 24.8 32.0 14.4 12.4 15.5 12.9
Imphal 31.1 23.3 30.2 23.5 29.6 22.9 25.0 29.5 24.6 28.6 24.3 28.3 3.9 3.6 5.0 4.6
Indore 41.1 20.7 40.4 20.6 38.9 21.0 25.7 31.0 25.2 30.0 24.8 29.8 8.2 5.0 9.7 6.5
Vdbalpur 42.6 22.7 41.2 23.2 39.8 22.5 26.8 31.8 26.4 32.0 26.0 31.2 7.8 6.7 9.3 7.6
Jagdelpur 39.4 22.3 38.6 22.5 37.4 22.4 26.4 32.4 25.9 31.8 25.4 30.7 8.9 7.9 10.1 8.7
Jaipur 42.8 22.5 41.4 22.6 39.4 22.6 27.4 33.1 27.0 32.1 ‘26.6 31.7 6.4 4.5 8.0 5.8
Jaisalmer 43.7 23.7 42.5 23.1 41.4 23.5 27.7 34.8 27.3 34.5 26.9 34.4 5.0 2.5 6.5 3.7
Jamnagar 37.1 24.4 36.1 25.6 35.3 25.1 29.2 33.0 28.4, 32.5 27.9 32.0 10.0 8.6 11.7 10.5
Jodhpur 42.0 23.2 40.8 23.0 39.6 22.7 28.0 35.4 27.4 33.7” 26.9 33.8 7.5 4.3 8.7 5.4
Jorhat 34.4 28.2 33.6 27.7 32.9 27.3 28.7 32.7 28:3 32.1 28.0 31.8 9.6 9.0 10.6 10.1
Kolkata 37.2 25.4 36.2 26.1 35.2 26.5 29.5 34.3 29.0 33.4 28.6 32.7 12.0 10.9 13.1 12.9
Kota 43.5 23.0 42.4 22.6 41.2 22.6 27.3 35,2 26.8 33.0 26.5 31.8 9.9 6.7 10.8 7.6
Kumool 41.6 23.2 40.3 24.6 38.9 24.4 29.3 34.8 28.8 34.i! 28.4 33.4 2.7 2.3 4.0 3.5
Lucknow 42.0 24.2 40.8 24.8 39.3 24.5 28.8 33,3 28.4 32.4 28.0 322 ?.5 6.8 8.4 7.7
Mangsdore 33.9 24.4 33.9 24.0 33.4 24.2 27.1 31.0 26.7 31.0 26.k” 30.7 19.7 17.0 20.s 18.1
Mumbai 35.3 22.8 34.3 23.3 33.5 24.0 27.9 31.8 27.5 31.3 {27.2 31.1 16.5 13.9 17.8 14.8
Nagpur 43.8 23.6 42.6 23.9 41.4 23.6 27.3 31.2 26.6 33.2 26.2 31,9 11.5 9.4 12.8 10.2
Nellore 40.4 27.8 39.0 28.1 37.8 27.2 30.0 37.1 29.4 35.4 28.8 34.0 19.4 18.3 20.2 19.3
New Delhi 41.8 23.6 40.6 23.8 39.4 23.5 28.4 33.3 28.0 33.3 27.6 32.7 6.0 5.2 7.1 6.3
Panjim 34.0 24.8 33.5 25.2 33.0 25.2 27.7 32.3 27.4 31.5 27.0 30.9 19.6 17.8 20.3 18.7
Patna 40.7 23.4 39.5 23.7 38.0 24.7 29.0 33.9 28.6 33.1 28.3 32.6 8.0 7.6 9.2 8.6
Ptme 38.4 20.5 37.4 20.4 36.3 20.6 24.8 30.9 24.4 30.6 24.0 29.6 9.2 8.0 10.3 9.2
Raipur 43.6 23.3 42.2 23.3 40.8 23.0 27.1 31.8 26.8 32.0 26.5 31.2 11.3 9.9 12.6 10.4
Rajkot 40.8 23.1 39.9 23.8 38.9 23.4 28.1 33.9 27.6 33.3 27.1 32.3 10.9 6.5 12.2 7.7
Ramagundam 43.4 25.6 42.2 25.1 40.7 25.8 28.3 37.3 27.9 35.6 27.4 34.4 12.5 11.2 13.7 12.5
Ranchi 38.9 22.1 37.7 21.8 36.4 21.5 26.2 31.7 25.6 30.4 25.2 29.2 9.1 7.2 10.4 8.3
Ratnagiri 34.1 22.4 33.4 23.2 32.8 23.6 27.6 31.1 27.3 30.8 27.0 30.2 18.3 14.9 19.2 16.5
Raxaul 38.6 23.1 36.9 24.5 35.5 24.6 28.9 33.0 28.4 32.0 28.1 31.8 7.5 7.3 8.5 8.2
Sabrsranpur 41.3 23.8 39,6 24.6 38.1 24.0 28.5 33.6 28.1 32.9 27.8 32.5 1.7 1.5 3.0 2.7
Shlllong 24.2 19.7 23.5 19.4 22.8 18.9 20.7 23.3 20.3 22.7 19.9 22.2 -1.0 -1.1 0.1 -0.5
Sholapur 41.1 21.6 40.1 21.6 39.1 21.2 26.6 32.6 25.8 32.1 25.1 3L5 16.3 12.4 17.2 12.5
Sundemagar 36.1 19.1 34.6 19.9 33.1 19.4 25.2 30.1 24.8 29.2 24.4 28 1.8 1.3 2.8 2.2
Surat 38.4 22.7 36.9 23.9 35.7 23.4 28.3 32.4 27.9 31.7 27.6 31.4/ 14.8 t2.6 16.2 12.5
Tezpur 34.2 27.4 33.3 26.5 32.5 27.1 28.9 32.8 28.4 31.8 28.0 31.4, 10.5 10.0 12.4 10.9
Tmchlrapali 39.6 24.6 38.7 25.1 37.8 24.9 27.7 34.5 27.2 33.7 26.9 33.3 19.3 18.2 20.1 18.7
Thimvanrmtha- 33.9 26.0 33.4 26.1 32.9 25.9 27.7 32.4 27.4 31.9 27.0 31.0 #2L6 20.1 22.2 20.8
puram
Veraval 35.2 23.9 33.8 23.5 32.8 26.6 29.1 32.3 28.7 31.6 28.4 31.1 14.3 lQ.1 15.6 12.3
Visakhapatnarn 36.4 26.5 35.6 27.3 35.0 27.1 29.2 33.8 28.8 33.0 28.4 32.5 15.4 14.9 16.8 16-2

DBT — Drybulbtemperature
WBT — Wet-bulbtemperature
MCDB — Mean coincidentaldry-bulbtemperature
MCWB — Mean coincidentalwet-bulbtemperature.

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 19


T---

for heating loads. For critical applications values under loads and the practical cooling and heating range of
0.4 percent column could beused for cooling loads the air.
and 99.6 percent column for heating loads.
4.4.6 Air Movement
For critical jobs and high energy consumption
applications, hourly load analysis should be evaluated a) In air conditioned spaces — Air movement
using computer programmed. is desirable, as it contributes a feeling of
freshness, although excessive movement
For industrial and other specific applications, the design should be avoided as this leads to complaints
conditions shall be as per user’s requirement. ‘ of draughts. The speed of an air current
Adequate movement of air shall always be provided becomes more noticeable as the air temperature
in an air conditioned enclosure, but velocities in excess falls, owing to its increased cooling effect.
of 0.5 nds in the zone between floor level and 1.5 m The design of the air distribution system
level shall generally be avoided; in the case of comfort therefore has a controlling effect of the
air conditioning, recommended air velocity is 0.13 nds quantity and temperature of the air that may
to 0.23 m/s in this zone, except in the vicinity of a be introduced into a space. The quantity of
supply or return air grille. fresh air should not be increased solely to
create air movement; this should be effected
4.4.5 Minimum Outside Fresh Air by air re-circulation within the space or by
The fresh air supply is required to maintain an inducing air movement with the ventilation
acceptably non-odorous atmosphere (by diluting body air system.
odorous and tobacco smoke) and to dilute the carbon b) In buildings — Air flow within a building
dioxide exhaled. This quantity may be quoted per should be controlled to minimize transfer of
person and is related to the occupant density and fumes and smells, for example from kitchens
activity within the space. Table 4 gives minimum fresh to restaurants and the like. This is achieved
air supply rates for mechanically ventilated or air by creating air pressure gradients within the
conditioned space. The quantity and distribution of building, by varying the balance between the
introduced fresh air should take into account the natural fans introducing fresh air and those extracting
infiltration of the building. the stale air. For example, the pressure should
be reduced in a kitchen below that of the
Table 4 specifies requirements for ventilation air adjacent restaurant.
quantities for 100 percent outdoor air when the outdoor
air quality meets the specifications for acceptable Care should be taken, however, to avoid excessive
outdoor air quality. While these quantities are for 100 pressure differences that may cause difficulty in
percent outdoor air, they also set the amount of air opening door or cause them to slam. In other cases,
required to dilute contaminants to acceptable levels. such as computer room, the area may be pressurized
Therefore, it is necessary that at least this amount of to minimize the introduction of dust from adjacent
air be delivered to the conditioned space at all times areas.
the building is in use, 4.4.6.1 Fire and smoke control
The proportion of fresh air introduced into a building
Air circulation system may be designed to extract
may be varied to achieve economical operation. When
smoke in event of a fire, to assist in the fire fighting
the fresh air can provide a useful cooling effect the
operation and to introduce fresh air to pressurize escape
quantity shall be controlled to balance the cooling
routes.
demand. However, when the air is too warm or humid
the quantity may be reduced to a minimum to reduce 4.4.6.2 Removal ofpar;iculate matterfrom air
the cooling load.
Efficient air filtration prevents fouling of the system
For transfer of heatlmoisture, air circulation is required and is of special importance in urban areas, where
to transfer the heat and humidity generated within the damage is likely to be caused to decorations and fittings
building. In simple systems the heat generated by the by discoloration owing to airborne dust particles. In
occupants, lighting, solar heat and heat from electrical order to obtain maximum filtration efficiency within
and mechanical equipment may be removed by the the minimum capital and maintenance expenditure, the
introduction and extraction of large quantities of fresh utmost care should be given to the location of the air
air. In more elaborate systems air maybe re-circulated intake in relation to the prevailing wind, the position
through conditioning equipment to maintain the desired of chimneys and the relative atmospheric dust
temperature and humidity. The air circulation rates concentration in the environs of the building; the
are decided in relation to the thermal or moisture recommendation for siting of air inlets given in 4.1

20 NATIONALBUILDING CODE OF INDIA


P

Table 4 Outdoor Air Requirements for Ventilation) of Air Conditioned Areas


and Commercial Facilities
(Clause 4.4.5)

S1 Application F.atimated
Maximumz) Outdoor Air Remarks
No. Occupancy Requirement
< A %
Persons/100mz I/s/Person (l/s)/mz
(1) (2) (3) (4) (5) (6)
i) Commercial dry cleaner 30 15
ii) Food and Beverage Service
Dining rooms 70 10
Cafeteria, fast food 100 10
Bars, cocktail lounges 100 15 Supplementarysmokeremovalequipmentmaybe
mquimd.
Kitchen (cooking) 20 8 Make up air for food exhaust may require more
ventilating air. The sum of tbe outdoor air and
transfer air of acceptable quafi~ from .ad@cettt
spacea shall be sufficient to provide an exhaust
rate of not less than 27.5 m3/h.m2(7.5 Vs.mz).
iii) Hotefs,Motefs,Resorts, Dormitories Independent of room size.
Bedrooms 15
Living rooms 15
Baths 18 Installed capacity for intermittent use.
Lobbies 30 8
Conference rooms 50 10
Assemble rooms 120 8
Dormitory sleeping areas 20 8 See also feed and beverage smba, merchan-
dising, barber and beauty shops,garage%offi@s.
Office space 7 10 Someofficeequipmentmayrequirelocal exhaust.
Reception areas 60 8
Telecommunication centers and 60 10
data entry areas
Conference rooms 50 10
iv) Public Spaces
Corridors and utiIities 0.25
Public restrooms, l/s/we or urinal 25 Normally supplied transfer sir.
Locker and dressing rooms 2.5 Local mechanical exhaust with no re-eircrdation
recommended.
Elevators 5.0 Normally supplied by transfer air.
Retail stores, sales floors and
show room floors
Basement and s~eet 30 1.50
Upper floors 20 1.00
Storage rooms 15 0.75
Dressing rooms 1.00
Mafls and arcades 20 1.00
Shipping and receiving 10 0.75
Warehouses 5 0.25
Smoking lounge 70 30 Normally supplied by transfer sir, loeaf
meehsnicaf exhaus~ exhaust with no recirculation
recommended.
,,
v) Specialty Shops
Barber Shop 25 8
Beauty Parlour 25 13
Florists 8 8 Ventilation to optimize growth may dictate
mydrements.
Clothiers, furniture 1.50
Hardware, drugs, fabric 8 8
Supermarkets 8 8
Pet shops 5.00
vi) Sports and Amusement

1-
Spectator areas 150 8 When intemsd combustion e@rres ate cqwrated
Game rooms 70 13 2.50 for maintenance of playing surfaces, incmwxf
Ice arenas (playing areas) ventilation rates may be required.

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING,HEATINGANDMECHANICALVENTILATION 21


?

Table 4 — Conck.fed

(1) (2) (3) (4) (5) (6)


SwimmingpOOk(pool and 2.50 Higher values may be required for humidity
deck area) control.
Playingfloors (gymnasium) 30 10
Ballroomsand discos 100 13
Bowlingalleys(seatingarea) 70 13

vii) Theatre
Ticketbooths 60 10
Lobbies 150 10 Specird ventilation will be needed to eliminate
Auditorium 150 8 speci~ stageeffects(for example,dry ice vaponrs,
mists,etc).
Stages,studios 70 8
viii) Transportation
Waitingrooms 100 8
Platforms Ventilation within vehicles may require special
100 8
consideration.
Vehicles 150 8
ix) Workrooms
Meatprocessing 10 8 Spacesmaintainedat lowtemperatureat (–1O”Fto
+ 50”F or -23°C to + IO”C)are not covered by
these requirements unless the occupancy is
continuous.Ventilation fionr adjoining spaces is
permissible.When the occupancyis interrnittenq
infiltration will normally exceed the ventilation
requirement.
Photo StUdiOS 10 8
Darkrooms 10 2.50
Pharmacy 20 8
Bank vaults 5 8
Duplicating,printing 2.50 Installed equipment shall incorporate positive
exhaust and control (as required) of undesirable
contaminants(toxicand otherwise).
E41ucation
Classrooms 50 8
Laboratories 30 10 Special contaminant control systems may be
Trainingshop 30 10 } required for processes or functions including
laboratoryanimalCn%upancy.
Musicrooms 50 8
Libraries 20 8
Lockerrooms 2.50
Corridors 0.50
Auditoriums 150 8
Hospita~ Nurses and Convakeent
Homes

Patientrooms 10 13 Special requirements or codes provisions and


Medicalprocedure 20 8 pressure relationships may determine ‘finimum
Operatingrooms 20 15 } ventilationrates and filter efficiency.
ProcedureRecoveryand ICU 20 8 Generating contaminants may require higher
rates.
Autopsy 2.50 .Air shallnot be rd:cmulated into other spaces.
Physicaltherapy 20 8
CorrectionalCells 20 10
Dininghalls 100 8
Guardstations 40 8

‘)This tableprescribessupplyrates of acceptableoutdoorair requiredfor acceptableindoorair quality.Thesevalueshave beenchosen


to dilute human bioeffluentsand other contaminantswith an adcmratemamin of safetvand to accountfor health variationsamong
people and varied activitylevels.
2)Net occupiablespace,

22 NATIONAL BUILDING CODE OF INDIA


should also be taken into account. Air filtration systems shall be in accordance with Part 4 ‘Fire and
equipment should be regularly serviced. Life Safety’.

Air borne dust and dirt may be generated within the 4.5.2.1 Design principles
building, from the interior finishes such as partitions,
The design of air conditioning system and mechanical
laminations, carpets, upholstery, etc, personnel and
ventilation shall take into accountdhe fire risk within
their movements as well as by machines such as,
the building, both as regards structural protection and
printers and fax machines.
means of escape in case of fire.
The degree of filtration necessary will depend on the
The extent and detail of statutory control and other
use of the building or the conditioned space. Certain
specialist interest may vary considerably according to
specialized equipment, normally associated with
the design, use, occupation and location of the building,
computers, will require higher than normal air filter
and the type of system of mechanical ventilation and
efficiencies for satisfactory operation. It is important
air conditioning proposed. It is therefore particularly
to ascertain the necessary standard of air cleanliness
important that the appropriate safeguards are fully
required for equipment of this type.
considered at the concept design stage of the building.
The choice of filtration systems will depend on the The degree of control and the requirements vary
degree of contamination of the air and on the cleanliness according to the application.
required. A combination of filter types may well give
the best service and the minimum operating costs. Full details may have to be approved by the Authority
in following cases:
The normal standard for intake filters in ventilating
a) From the point of view of the means of escape
and air conditioning applications is an efficiency of
(except dwelling houses) where recirculation
95 percent for a particle size up to 15 pm although
of air is involved and/or where pressurized
there may be a requirement for a higher efficiency to
staircases are contemplated as part of the
give increased protection against atmospheric staining.
smoke control arrangements;
Special applications, such as computer server rooms, b) Places of public entertainment; and
clean rooms, healthcare, pharmaceutical or food
c) Large car parks, hotels, parts of building used
processing, and air systems having induction units,
for trades or processes involving a special risk,
require a higher standard that is achieved by two stage
and departmental stores and similar shop risks
filtration. The exact requirements will depend on the
in large buildings.
equipment or process involved.
4.5.2.2 Ductwork and enclosures
4.4.6.3 Removal offimes and smells from air
All ductwork including connectors fittings and
Fumes and smells may be removed from air by physical
plenums should be constructed of steel, aluminium or
or chemical processes. These may be essential when
other approved metal or from non-combustible
ambient air is heavily polluted.
material. All exhaust ducts, the interior of which is
The decision to use odour-removing equipment will liable in normal use to accumulate dust, grease or other
normally be made on economic grounds, this may flammable matter, should be provided with adequate
become necessary by the currently rising cost of fuel. means of access to facilitate cleaning and inspection.
Once such equipment is installed, it has to be regularly Also, the concerned provisions of Part 4 ‘Fire and Life
serviced to ensure satisfactory performance. Failure Safety’ shall be complied with.
to do this may result in unacceptable conditions within
4.5.2.3 Thermal and acoustic insulation
the building.
To reduce the spread of fire or smoke by an air
4.5 Statutory Regulation and Safety Considerations conditioning system, care should be taken for the
4.5.1 Authorities and Approval of Schemes choice of materials used for such items as air filters,
silencers and insulation both internal and external (see
A ventilation or air conditioning system should comply Part 4 ‘Fire and Life Safety’ and Part 5 ‘Building
with the requirements laid down in the current statutory Materials’).
legislation or any revisions currently in force and
consideration should also be given to any relevant 4.5.2.4 Fire and smoke detection
insurance company requirements. When the system involves the recirculation of air,
consideration should be given to the installation of
4.5.2 Fire and Safety Considerations
detection devices that would either shut off the plant
Fire protection requirements of air conditioning and close dampers or discharge the smoke-laden air to

PART 8 BUILDINGSERVICES— SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 23


atmosphere. Detectors may be advisable in certain 4.6 Application Factors
applications even when the system is not a recirculator
4.6.1 General
one. Exhausts should not be positioned near the fire
escapes, main staircases or where these could be a This clause gives general guidance, for various
hindrance to the work of fire authorities. The local fire applications, for the factors that usually influence the
authorities should be consulted. selection of the type, design and layout of the air
conditioning or ventilating system to be used.
A careful study of the operating characteristics of each
type of sensing device should be made before selection. 4.6.1.1 Commercial applications
Smoke detectors are normally either of the optical or
The primary objective of the application described
ionization chamber type. These can be used to either
under this heading is provision of comfort conditions
sound an alarm system or operate a fire dampers. Care
for occupants.
should be taken with their location as various factors
affect the satisfactory operation. 4.6.1.2 Ojlices

Ionization type detectors are sensitive to high velocity Office building may include both external and internal
air streams and if used in ductwork the manufacturer zones.
should be consulted. Activation of smoke detector The external zone may be considered as extending from
should stop the air handling unit supply air fan, close approximately 4 m to 6 m inwards from the external
the fire damper in supply and return air duct and operate wall, and is generally subjected to wide load variation
a suitable alarm system. owing to daily and annual changes in outside
In all the above instances the appropriate controls temperature and solar radiation. Ideally, the system(s)
would require manual re-setting. selected to serve an external zone should be able to
provide summer cooling and winter heating. During
4.5.2.5 Smoke control intermediate seasons the external zone of one side of
While it is essential that the spread of smoke through the building may require cooling and at same time the
a building to be considered in the design of air external zone on another side of the building may
conditioning systems for all types of applications, it require heating. The main factors affecting load are
assumes special significance in high rise buildings, usually window area and choice of shading devices.
because the time necessary for evacuation may be The other important factors are the internal gain owing
greater than the time for the development of untenable to people, light and office equipment. Choice of system
smoke conditions on staircases, in lift shafts and in may be affected by requirements to counteract down
other parts of the building far away from the fire. Lifts draughts and chilling effect due to radiation associated
may be filled with smoke or unavailable, and, if mass with single glazing during winter.
evacuation is attempted, staircase may be filled with Internal zone loads are entirely due to heat gain from
people. people, lights and office equipment, which represent a
One or more escape staircase connecting to outdoors fairly uniform cooling load throughout the year.
at ground level, should be pressurized, to enable mass Other important considerations in office block
evacuation of high rise buildings (see also Part 4 ‘Fire applications may include requirements for individual
and Life Safety’ ). controls, partitioning flexibility serving multiple
Therefore all air handling systems of a building should tenants, and requirement of operating selected areas
be designed with fire protection and smoke control outside of normal office hours. Areas such as
aspects incorporating, where appropriate, facilities to conference rooms, board rooms, canteens, etc, will
permit their operation for the control of smoke within often require independent systems.
the building in event of fire. For external building zones with large glass areas, for
example, greater than 60 percent of the external fagade,
The pressurization systems for staircases use large
the air-water type of system, such as induction or fan
volumes of outside air. The system may be designed
coil is generally economical than all air systems and
to operate continuously at low speed, being increased
has lower space requirements. For external zones with
to high speed in the event of fire, or to operate only in
small glass areas, an all air system, such as variable
emergency. Noise and droughts are not considered a
volume, may be the best selection. For building with
problem in an emergency situation. Fan motor and
average glass areas, other factors may determine the
starter should be protected from fire and connected to
choice of system.
the emergency electrical supply through cables with
special fire resistant coating (see also Part 4 ‘Fire and For internal zones, a separate all-air system with
Life Safety’ ). volume control may be the best choice. Systems

24 NATIONAL BUILDING CODE OF INDIA


employing reheat or air mixing, while technically For large department stores a very careful analysis of
satisfactory, are generally poor as regards energy the location and requirement of individual department
conservation. is essential as these may vary widely, for example, for
lighting departments, food halls, restaurants, etc. some
4.6.1.3 Hotel guest rooms system flexibility to accommodate future changes may
In ideal circumstances, each guest room in a hotel or be required.
motel should have an air conditioning system that Generally, internal loads from lighting and people
enables the occupant to select heating or cooling predominate. Important considerations include initial
as required to maintain the room at the desired and operating costs, system space requirements, ease
temperature. The range of temperature adjustment of maintenance and type of operating personnel who
should be reasonable but, from the energy conservation will operate the system.
view point, should not permit wasteful overcooking or
overheating. The all-air type of system, with variable volume
distribution from local air handling units, may be the
Guest room systems are required to be available for most economical option. Facilities to take all outside
operation on a continuous basis. The room may be air for ‘free-cooling’ under favorable conditions
unoccupied for most of the day and therefore provision should be provided.
for operating at reduced capacity, or switching off, is
essential. Low operating noise level, reliability and ease 4.6.L6 Theatres/Auditoria
of maintenance are essential. Treated fresh air Characteristics of this type of application are buildings
introduced through the system is generally balanced generally large in size, with high ceiling, low external
with the bathroom extract ventilation to promote air loads, and high occupancy producing a high latent gain
circulation into the bathroom. In tropical climates, and having low sensible heat factor. These give rise to
where the humidity is high an all-air system with the requirements of large fresh air quantities and low
individual room reheat (and/or retool) may be operating noise levels. Theatres and auditoria maybe
necessary to avoid condensation problems. Fan coil in use only a few hours a day.
units are generally found to be most suitable for this
kind of application with speed control for fan and 4.6.1.7 Special applications
motorised/modulating valve for chilled water control 4.6.L7.I Hospitals/Operating theatres
for cooling.
In many cases proper air conditioning can be a factor
4.6.1.4 Restaurants, cafeteria, bars and night-clubs in the therapy of the patient and in some instances part
Such applications have several factors in common; of the major treatment. For special application areas
highly variable loads, with high latent gains (low of hospitals such as operation theatres, reference may
sensible heat factor) from occupants and meals, and be made to specialist literature.
high odour concentrations (body, food and tobacco The main difference in application compared with other
smoke odours) requiring adequate control of fresh air applications are:
extract volumes and direction of air movement for
avoidance of draughts and make up air requirements a) Restriction of air movement between various
for associated kitchens to ensure an uncontaminated departments and control of air movement
within certain departments, to reduce the risk
supply.
of airborne cross infection;
This type of application is generally best served by b) Specific need for the ventilation and filtration
the all-air type of system preferably with some reheat equipment to dilute and/or remove particulate
or return air bypass control to limit relative humidity. or gaseous contynination and airborne micro-
Either self-contained packaged units or split systems, organisms;
or air-handling unit served from a central chilled
c) Close tolerances in temperatures and
system may be used. Sufficient control flexibility to
humidities may be required for various areas;
handle adequately the complete range of anticipated
and
loads is essential.
d) The design should allow for accurate control
4.6.1.5 Department stores/shops of environmental conditions.

For small shops and stores unitary split type air For (a) and (b) the air movement patterns should
conditioning systems offer many advantages, including minimize the spread of contaminants as for instance,
low initial cost, minimum space requirement and ease in operating departments where the airflow should be
of installation. such as to reduce the risk of periphery or floor-level

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING. HEATING AND MECHANICAL VENTILATION 25
P

air returning to the patient owing to secondary air temperature variations owing to fluctuation in heat
currents whilst the general pressurization pattern load. Overhead air supply through ceiling plenums
should cause air to flow through the department from utilizing linear diffuser or ventilated ceilings is
sterile to less sterile rooms in progression. In operating eminently suited to computer room application,
theatres 100 percent fresh air system is normally permitting high air change rates to be achieved without
provided and air pressures in various rooms are set by undue discomfort to persormel.
use of pressure stabilizers. Many types of air
The air conditioning system should be reliable because
distribution pattern within operation theatres are in use
failure to maintain conditions for even a short duration
but generally they conform to high-level supply and
can cause substantial monetary loss and possibly more
low-level pressure relief or exhaust. There is also need
serious consequence. As such standby equipment is
for a separate scavenging system for exhaled and waste
recommended,
anesthetic gases with in theatre suites where general
anesthetic may be administered. 4.6.1.8 Residential buildings

When zoning air distribution systems to compensate for Very few residences are air conditioned. Some
building orientation and shape, consideration should be individual houses have unitary systems comprising of
given to ensure that the mixing of air from different windowlsplit air conditioners. Some large houses have
departments is reduced to a minimum. This can be VRV based splits and some luxury block of flats are
accomplished by the use of 100 percent conditioned provided with air-water systems. VAV also works well
fresh air with no re-circulation or, where re-circulation for some luxury applications with chilled water
is employed, by providing separate air handling systems applications. In the latter case, most of the considerations
for different departments based on the relative sensitivity of 4.6.1.3 apply.
of each to contamination. A degree of stand-by is
provided by this system so that breakdown will affect 5 NOISE AND VIBRATION CONTROL
only a limited section of the hospital. 5.1 General
Laboratories and other areas dealing with infectious Noise is unwanted sound. All ventilating and air
diseases or viruses, and sanitary accommodation conditioning systems will produce noise, and this may
adjacent to wards, should be at a negative air pressure cause annoyance or disturbance in:
compared to any other area to prevent exfiltration of
any airborne contaminants. In extreme cases any a) the spaces being treated;
exhaust to atmosphere from these areas has to pass b) other rooms in the building;
through high efficiency sub-micron particulate air c) the environment external to the building.
(HEPA) filters.
In the case of external environment particular care
4.6.1.7.2 Computer rooms should be taken to avoid a nuisance in the ‘silent’ hours,
and local authorities have statutory powers to ensure
The equipmen~ in computer rooms generates heat and that noise from plant is limited.
contains components that are sensitive to sudden
variations of temperature and humidity. These are It is important that expert advice be sought in dealing
sensitive to the deposition of dust. Exposure beyond with noise and vibration problems, as for obvious
the prescribed limits may result in improper operation reasons the most economic~ solutions should be used,
or need for shut-down of the equipment. The without impairing the performance.
temperature and humidity in computer rooms need to
5.2 Types of Noise in Building
be controlled within reasonably close limits, although
this depends on the equipment involved. The relative 5.2.1 Externally Created Noise
humidity may be controlled within+ 5 percent in the
Reduction of externally created noise is mainly dealt
range 40 percent to 60 percent. Manufacturers normally
with by choice of building profile and window
prescribe specific conditions to be maintained. Typical
construction. The air conditioning designer should,
conditions are air dry-bulb: 21 * 1.6”C; relative
however, ensure that noise does not enter via air inlets
humidity 50* 5 percenq and filtration 90 percent down
or exhausts: it maybe reduced by suitable attenuators.
to 10 microns.
5.2.2 Generated Noise
A low velocity re-circulation system maybe used with
5 percent to 10 percent fresh air make-up which is Noise produced by the components of air conditioning
allowed to exfiltrate from the room and ensure a and ventilation plant installed within the building can
positive pressure to prevent entry of dust and untreated escape via ventilation grilles or door openings and can
air. The air distribution should be zoned to minimize cause nuisance to neighbors. Equipment mounted

26 NATIONAL BUILDING CODE OF INDIA


outside the building may well need to be selected or b) Install it at a serviceable height.
installed with the noise problem in mind. c) Install preferably in a wall or on a rigid
window.
Another type of generated noise is created by the air-
circulating system itself and its associated equipment. d) Provide only necessary slope as specified by
Fans are an obvious source, but noise can be produced the manufacturer, to avoid any unusual noise
by turbulence, which may cause vibration of the ducts from the compressor because of tilting.
and noise transmission by air diffusers. This problem e) Install it preferably in the middle portion of
can be avoided by careful selection of and installation the wall/window to avoid additional directivity
equipment or by the noise absorbing devices. (do not install at the end of a wall.

5.2.3 Transmitted Noise ‘ f-) Ensure all leaks are sealed properly.
g) Avoid condenser facing any high noisy areas,
Noise transmitted through the building structure is such as roadlfactory to avoid any such noise
particularly acute in modern frame and reinforced predominantly entering into the room.
concrete buildings. Such noise can be controlled by
h) Do not provide any props at the back side
isolating the machines from the structures, and from
bottom of the air conditioner unless specified
pipe work connected to the building, by suitable
by the manufacturer.
mountings and pipe couplings.
j) Prepare the opening to suit the chassis with
Another problem is the transmission of” sound from wooden frame of adequate rigidity and
one room to another via air ducting, ventilated ceilings thickness.
or other continuous airspace. Such sound includes the
noise from machines and equipment and also 5.5.2 From Split Air Conditioner/Furred Inn
of conversation, transmission of which can be The following measures should be adopted:
embarrassing as well as annoying. Again, this problem
can be tackled by careful design and the inclusion of a) Install the evaporator only on a rigid wall/
sound absorbing devices in ducts. ceiling or on a pedestal.
b) Avoid installation over wooden/gypsum
5.2.4 Intermittent Noise
board partition. Should a need arise anchor
Such noise arises from the stopping and starting of the evaporator rigidly by using mild steel
equipment, and the opening and closing of valves and frame work from the roof to avoid vibration.
dampers. This may or may not cause problems in the c) Provide proper ‘u’ trap in the condensate
air conditioned spaces, but it is often objectionable to water line to ensure a good water seal, which
plant operators and maintenance engineers. This should will also avoid sound penetration into the
be considered by air conditioning designer. room from outside.
5.3 The source of noise in the air conditioning system d) If the capillary is in the evaporator, ensure
could be from the following: that flow noise is avoided.
e) Ensure proper return air entry back to the coil,
a) Chillers,
since blowers working at higher static
b) Pumps, pressure will create higher noise.
c) Pipe supports, Select the condensers with top/side discharge
f)
d) Ducts, depending upon location to avoid nuisance
e) External noise infiltration though openings, to neighbors.
f) Fans, g) Place condensers on rigid platform, properly
Air noise through ducts, and supported propped and fixed ftiy.
g)
h) Compressors. h) Ensure all screws, bolts and nuts are firmly
tightened since stiffening is more advantageous
5.4 The approach must always be to reduce the source in higher frequencies for vibration reduction.
noise rather than controlling them in the path
5.5.3 Air Handling Units (Floor Mounted and Ceiling
5.5 Noise Control Suspended)
5.5.1 From Room Air Conditioners (RAC) The following measures should be adopted:
The following measures should be adopted: a) Selected indoor machine for specific air
a) Selection of RAC which has the least noise quantity and static pressure.
at various fan speeds. b) Suspend the indoor machine and ducts

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 27
without touching the members of the false for a more normal operating point and allowing fan
ceiling or partitions. noise to exceed the design criteria on the rare occasions
c) Ensure that ducts/duct supports do not touch when the fan operates at full output.
the evaporator. 5.5.5.3 To reduce fan noise, the following should be
5.5.4 From Plenum Chamber adopted:
a) Design the air distribution system for
The following measures should be adopted/considered:
minimum resistance, since the sound generated
a) If possible and if pressures allow, expand the by a fan, regardless of type, increase by the
air to a plenum chamber (of 2.5 m/s for square of the static pressure. Turbulence can
normal office), which is acoustically lined increase the flow noise generated by duct
inside. fittings and dampers in the air distribution
b) Stiffening of the plenum body is very critical systems especially at low frequencies.
since it could create a drumming noise. b) Examine the specific sound power levels of
c) Plenum chambers with sound absorbing the fan designs for any given job. Different
material are frequently used as silencers in fans generate different levels of sound and
air conditioning and ventilating systems and produce different octave band spectra. Select
in testing facilities to reduce flow velocity and a fan that will generate the lowest possible
turbulence. The attenuation of these devices sound level, commensurate with other fan
may be due to both dissipative and reactive selection parameters.
effects. c) Fans with relatively few blades (less than 15)
tend to generate tones, which may dominate
5.5.5 From Fans
the spectrum. These tones occur at the blade
5.5.5.1 Centrifugal fans passage frequency and its harmonies. The
intensity of these tones depends on resonance
There are three basic types of centrifugal fans,
with the duct system, fan design, and inlet
backward curved, forward curved, and radial. Noise
flow distortions.
from centrifugal fans is dominantly a superimposition
of discrete tones at the varying frequencies and d) Select a fan to operate as near as possible to its
broadband aerodynamic noise. rated peak efficiency when handling the
required quantity of air and static pressure.
5.5.5.2 Axialfans Also, select a fan that generates the lowest
Axial fans derive their name from the fact that the possible noise but still meets the required
design conditions for which it is selected. Using
airflow is along the axis of the fan. To avoid a circular
an oversized or undersized fan, that does not
flow pattern and to increase performance, guide vanes
are usually installed downstream of the rotor. Axial operate at or near rated peak efficiency, may
result in substantially higher noise levels.
fans with exit guide vanes are called vane axial and
those without guide vanes are called tube axial. Axial e) Design duct connections at both the fan inlet
fans generally operate at higher pressures than and outlet for uniform and straight airflow.
centrifugal fans and are usually considered noisier. Avoid unstable, gusting, and swirling inlet
Common applications include heating and ventilation airflow. Deviation from accepted applications
systems. Because of the large number of blades and can severely degrade both the aerodynamic
high rotational speeds, noise from axial fans is and acoustic performance of any fan and
generally characterized by strong discrete blade invalidate manufacturers ratings or other
passing tones. performance predi@ions.
f) Select duct silencers that do not significantly
Variable inlet vane system may generate significantly
increase the required fan total static pressure.
low frequency noise as the vanes shutdown. Additional
attenuation with a corresponding additional pressure 5.5.6 From Chillers, Pumps and Pipes
drop is required to attenuate the noise generated by Sizing and selecting a chiller is an important aspect in
the inlet vanes. noise control. The following guidelines may be
Variable speed motors and drives and variable pitch considered for noise control:
fan blade systems are actually quieter at reduced air a) For rooftop installation of chillers, these may
output than at full output. The designer has the option be placed on beams comected on the elevated
of designing for maximum output as if the system were levels of pillars on correctly chosen vibration
constant volume, or selecting the sound attenuation isolators.

28 NATIONAL BUILDING CODE OF INDIA


b) Water cooled chillers have less vibration. inside the duct can be avoided. The density is
However, if air cooled chillers have to be to be decided based on the outside noise level.
chosen, choose them with fan of less speeds n) Selection of a proper terminal device helps
and compressors must be jacketed without in noise reduction.
compromising their ventilation requirement. VAV shall be planned along with relevant
P)
c) If much more silencing is required, plan a VFD or bypass arrangement. Otherwise the
silencer on the exhaust of the fans and also duct is subjected to variable pressures
an acoustic enclosure around the chillers. Care resulting in variable noise pattern.
must be taken for the additional static demand
I @ Minimize flow-generated noise by elbows or
in the fan. duct branch takeoffs, whenever possible, by
5.5.7 From Ducting Work locating them at least four to five duct
diameters from each other. For high velocity
The following measures should be adopted:
systems, it maybe necessary to increase this
a) Shorter ducts with flanges and bracings is very distance to up to ten duct diameters in critical
advantageous for noise reduction. noise areas.
b) Choose the right thickness of sheets for r) Keep airflow velocity in the duct as low as
ducting. possible (7.5 nds or less) near critical noise
c) Provide calculated turning vanes in all bends. areas by expanding the duct cross-section
d) Provide take off pieces in all branches and area. However, do not exceed an included
collars. expansion angle of greater than 15°. Flow
separation, resulting from expansion angles
e) Minimize the number of terminals since each
greater than 15°, may produce rumble noise.
terminal of equal noise will create a higher
Expanding the duct cross-section area reduces
overall noise inside the room — Two equal
potential flow noise associated with turbulence
noise source increase the noise by 3 dB.
in these areas.
f) Velocities of supply and return ducts and also
s) Use turning vanes in large 90° rectangular
terminals are important for noise control.
elbows and branch takeoffs. This provides a
g) For auditoriums, conference halls etc, choose smoother transmission in which the air can
the right silencers in the supply. Define a change flow direction, thus reducing turbulence.
clear opening for return air and fix return
t) Place grilles, diffusers and registers into
air silencers (parallel baffle silencer).
occupied space as far as possible from elbows
The pressure drop expected across these
and branch takeoffs.
silencers varies from 6 mm to 10 mm of water
column. u) Minimize the use of volume dampers near
grilles, diffusers and registers in acoustically
h) Selecting double skin air handling unit should
critical situations.
be done with care. If used without supply and
return air silencers it adds to the noise in the v) Vibration isolate ducts and pipes, using spring
duct patch. However, by using double skin and/or neoprene hangers for atleast the fiist
air handling” unit the noise inside the plant 15 m from the vibration-isolated equipment.
room can be lowered.
5.6 Structure Borne Noise
j) Instead of insulating the plant room, increasing
the density of the plant room wall and Most obvious paths for solid-borne noise are the
providing return air baffles in the return air attached piping and pump support systems. Oscillatory
patch is more helpful in noise reduction. The energy generated near the pump can be conducted as
doors to the air handling unit room should be solid-borne noise for substantial distances before it is
either with an attic entry or dense enough to radiated as acoustic noise. It can be controlled using
avoid noise transmission. flexible couplings and mechanical isolation.
k) Avoid terminal dampers and grilles if the
5.7 Measurement
noise criteria is of the order of NC 20
(recording studios). Measurements should be taken with a sound level meter
m) If ducts have to be routed outside the either using the ‘A’ weighting scale or to draw up a
conditioned space, the density of the noise criteria curve (see Part 8 ‘Building Services,
insulating materials over the duct surface is Section 4 Acoustics, Sound Insulation and Noise
very critical. Higher the density, lower is its Control’ ). Measurements should be taken in the
noise transmitality and hence break in noise following locations:

PART 8 BUILDING SERVICES — SECTION 3 ALR CONDITIONING, HEATING AND MECHANICAL VENTILATION 29
a) Plant rooms; various parameters that affect the type of ventilation
b) Occupied rooms adjacent to plant rooms; system selected for a particular application, and the
c) Outside plant rooms facing air intakes and sizing of the ventilation plant:
exhausts and condenser discharge, to assess a) The climatic zone in which the building is
possible nuisance to adjacent occupied areas; located is a major consideration. An important
d) In the space served by the first grille or distinction that must be made is between hot-
diffuser after a fan outlet; and dry and warm-moist conditions. Hot-dry work
e) In at least two of the spaces served by fan situations occur around furnaces, forges,
coil units or high velocity system te~inal metal-extruding and rolling mills, glass-
units (where applicable). forming machines, and so forth.
Typical warm-moist operations are found in
6 MECHANICAL VENTILATION (FOR NON AIR textile mills, laundries, dye houses, and deep
CONDITIONED AREAS) AND EVAPORATIVE mines where water is used extensively for dust
COOLING control.
6.1 Ventilation Warm-moist conditions are more hazardous
than the hot-dry conditions.
Ventilation is the process of changing air in an enclosed
b) Siting (and orientation) of the building is also
space. A proportion of the air in the space should be
an important factor. Solar heat gain and
continuously withdrawn and replaced by fresh air
high outside temperature increase the load
drawn from outside to maintain the required level of
significantly; how significantly depends, on
air purity. Ventilation is required to control the
the magnitude of these gains particularly in
following:
relation to other gains for example the internal i
a) Oxygen Content — Prevent depletion of the load.
oxygen content of the air; c) The comfort level required is another
b) Carbondioxide and Moisture — To prevent consideration. In many cases, comfort levels
undue accumulation; (as understood in the context of Residential
c) Contaminants — To prevent undue rise in Buildings, Commercial Blocks, Office
concentration of body odours and other Establishments) cannot be achieved at all and
contaminants such as tobacoo smoke; therefore, what is often aimed at will be
d) Bacteria — To oxidize colonies of bacteria ‘acceptable working conditions’ rather than
and fungas to prevent their proliferation. ‘comfort’.
e) Heat — To remove body heat and heat Having surveyed the considerations above,
dissipated by electrical or mechanical there are many options available in mechanical
equipment or solar heat gains. ventilation — spot cooling, local exhaust,
changes in work pattern — to choose from, <
Mechanical ventilation is one of several forms of for achieving the desired acceptable working
ventilation options available. It usually consists of fans, conditions. The options available may need
filters, ducts, air diffusers and outlets for air distribution to be extended to evaporative cooling in
within the building. It may include either mechanical order to achieve more acceptable working
exhaust system or exhaust can occur through natural conditions when confronted with more hostile
means. environmental conditions.
Natural ventilation and natural exhaust are also options It will be thus seen that there are many
(see Part 8 ‘Building Services, Section 1 Lighting and considerations ipvolved in the selection and
Ventilation’ ). The scope of this section is therefore sizing of suitable ventilation and evaporative
restricted to mechanical ventilation. cooling plants to meet the requirements of any
particular building and/or process. It is the
Ventilation controls heat, odours and hazardous interplay of these various factors listed above
chemical contaminants (in a building) that could affect like climatic conditions, internal load,
the health and safety of the occupants. For better exposure to heat and hazardous substances
control, heat and contaminants, air may need to be and level of working conditions aimed at, that
exhausted at their sources by local exhaust systems. determines the option, which best meets the
Usually such systems require lower air flows than requirement and also, the capacity and other
general (dilution) ventilation. attributes of the option selected.
Following considerations provide details regarding the Ventilation control measures alone are

30 NATIONAL BUILDING CODE OF INDIA


frequently inadequate for meeting heat stress achieved by providing the required amount of fresh
standards. Optimum solutions may involve air either to remove totally or to dilute odours, fumes,
additional controls, such as local exhausts, etc. Local extract systems may be necessary to remove
spot cooling, changes in work-rest patterns, polluted air from kitchens, toilets, slaughter houses,
and radiation shielding. crematoria, etc. Special air filters may be provided to
As a rule, it is the mechanical system that remove contaminants or smells when air is recirculated.
provides the best results and controls, for 6.2.5 Removal of Particulate Matterfrom Air
the more complex situations and more
stringent requirements arising out of harsher Efficient air filtration to prevent fouling of the system
environment and need for better working should be considered, where damage is likely to be
conditions. caused by discoloration owing to airborne dust
particles. In order to obtain the best performance from
6.2 Beneficial Effects of Ventilation the filters provided, care should be taken to locate the
6.2.1 Fresh Air Supply air intake appropriately in relation to the prevailing
wind, position of chimneys and relative atmospheric
Ventilation system provides the fresh air flow that is dust concentration in the environs of the building.
required to maintain an acceptable non-odorous
atmosphere (by diluting body odours and tobacco This will promote cleaner interiors and reduce dust
smoke) and to dilute the carbon dioxide exhaled. loading of the filters. Adequate (space) provisions
should be incorporated in plant layout to ensure that
The quantity and distribution of introduced outside air filters can be serviced regularly.
takes into account infiltration, exhaust and dilution
requirements of the building. Proportion of fresh air 6.2.6 Fire and Smoke Control
introduced into a building may be varied to achieve Ventilation system can be designed to extract smoke
economical operation. When fresh air can provide in the event of a fire, to assist in the fire fighting
useful cooling effect, the quantity should be controlled operations and to introduce fresh air to pressurize
to match the cooling demand. escape routes.
6.2.2 Transfer of Heat/Moisture 6.2.7 Removal of Fumes and Smells from Air
Ventilation system helps air circulation that is required Fumes and smell may be removed from air by physical
to transfer the heat and humidity generated within the or chemical processes. Their removal may be essential
building. Heat generated by the occupants, electrical when the ambient air is heavily polluted, although
and mechanical equipment, and solar heat gains may consideration must be given to limit the thermal loads
be removed by the introduction of adequate quantities caused by the introduction of large quantities of fresh air.
of fresh air and by expelling or extracting of stale air.
6.3 Industrial Ventilation
6.2.3 Air Movement
Industrial buildings form a major application of
Ventilation system provides air movement that is
mechanical ventilation.
necessary to create a feeling of freshness and avoid
discomfort, although excessive movement should be in industrial buildings, ventilation is needed to provide
avoided as this may lead to complaints of draughts. the fresh air normally required for health and hygiene
The quantity of fresh air should not be increased solely and also, to mitigate thermal working conditions by
to create air movement; this should be effected by air assisting in removal of surplus heat due to equipment,
recirculation within the space or by inducing air people and building heat gains.
movement with the ventilation air system. Following are some of t~ factors that should be
Air flow should be controlled to minimize transfer of considered in the system design:
fumes and smells. In addition, air pressure gradients may a) A supply system would not be satisfactory
be created within the building, by varying the balance without a complementary exhaust system.
between the fresh air and extracting the stale air. Similarly any exhaust system would require
Care should be taken, however, to avoid excessive for complementary supply system.
pressure differences that can cause difficulty in opening b) Air should be supplied equitably through
doors or cause them to slam. grilles, diffusers — and such other devices.
Directional grilles, diffusers and nozzles
6.2.4 Air Purity and Filtration
designed specifically to alleviate the thermal
Ventilation system installed in a building should deliver conditions should be considered. Drafts
clean, fresh air to the space served, This may be should be avoided.

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 31
.,

I!f’7’$”
.
c) Ventilation systems may need to be 6.5 Ventilation Rate and Design Coniderations for
supplemented by exhaust hoods and canopies Non Air Conditioned Areas
designed to capture the unwanted fumes or 6.5.1 General Ventilation
dust right at the source irrespective ofother
The rate of air circulation recommended for different
air currentsin the vicinity.
general areas is as given in Table 5.
Many industrial ventilation systems shall handle
Table 5 Recommended Rate of Air Circulation
simultaneous exposures to heat, toxic and hazardous
for Different Areas
substances. The number of contaminant sources, their
(Clause 6.5.1)
generation rate and effectiveness of exhaust hoods are
rarely known; there is no option but to depend on S1 Application Air Change
No. per Hour
common ventilatiordindustrial hygiene practice in such
(1) (2) (3)
situations.
1. Assembly rooms 4-8
Reference may also be made to good practice [8-3(4)]. 2. Bakeries 20-30
3. Banks/building societies 4-8
6.4 Types of Ventilation Systems 4. Bathrooms 6-10
5. Bedrooms 2-4
In the interest of efficient use of energy and comfort 6. Billiard rooms 6-8
7. Boiler rooms 15-30
to the occupants, it is imperative that all modes of
8. Cafes and coffee bars 10-12
ventilation should be considered in relation to the 9. Canteens 8-12
thermal characteristics of the building. 10. Cellars 3-1o
11. Churches 1-3 I
6.4.1 Mechanical Extract/Natural Supply 12. Cinemas and theatres 10-15
13. Club rooms 12, Min
This is simplest form of extract system comprising one 14. Compressor rooms 10-12
15. Conference rooms 8-12
or more fans, usually of the propeller, axial flow or
16. Dairies 8-12
mixed flow type, installed in outside walls or on the 17. Dance halls 12, Min
t
roof. The discharge should terminate in louvers or 18. Dye works 20-30
19. Electroplating shops 10-12
cowls or a combination of both.
20. Engine rooms 15-30
Alternatively, the system may comprise of ductwork 21. Entrance halls 3-5
22. Factories and work shops 8-10
arranged for general extraction of the vitiated air or 23. Foundries 15-30
for extraction from localized sources of heat, moisture, 24. Garages 6-8
25. Glass houses 25-60
odours, fumes and dust. Such duct work may be
26. Gymnasium 6, Min
connected to centrifugal or axial flow fans that 27. Hair dressing saloon 10-15
discharge through the wall or roof, terminating in 28. Hospita.ls-sterlising 15-25
29. Hospital-wards 6-8
louvers or cowls or a combination of both.
30. Hospital domestic 15-20
31* Laboratories 6-15
It is essential that provision for make-up air is made
32. Launderettes 10-15
and that consideration is given to the location and size 33. Laundries 10-30
of inlet. Inlet should not be located in the vicinity of 34. Lavatories 6-15
exhaust fan. 35. Lecture theatres 5-8
36. Libraries 3-5
6.4.2 Mechanical Supply/Natural Extract 37. Living rooms 3-6
38. Mushroom houses 6-10
This system is similar in form to the extract system 39. Offices 6-10
but arranged to deliver fresh air positively into the 40. Paint shops (not cellulose) 10-20
41. Photo and X-ray darkroom 10-15
enclosed space. Such a system necessitates provision 42. Public house bars 12, Min
for the discharge of vitiated air by natural means. 43. Recording control rooms 15-25 Y
Where there is a requirement for the enclosed space to 44. Recording studios 10-12
45. Restaurants 8-12
be at a slightly higher pressure than its surroundings 46. Schoolrooms 5-7
(to exclude dust or smoke, for example), the discharge 47. Shops and supermarkets 8-15
may be through natural leakage paths or balanced 48. Shower baths 15-20
.
49. Stores and warehouses 3-6
pressure relief dampers, as maybe required. 50. Squash courts 4, Min
51. Swimming baths 10-15
6.4.3 Combined Mechanical Supply and Extract
52. Toilets 6-10
This system is a combination of those described above 53. Utility rooms 15-20
54. Welding shops 15-30
and may comprise supply and exhaust ductwork
systems or may employ a common fan with a fresh air NOTE — The ventilation rates maybe increased by 50 percent
where heavy smoking occurs or if the room is below ground.
inlet on the low pressure side.

32 NATIONAL BUILDING CODE OF INDIA


6.5.2 Kitchen (Industrial and Commercial) Ventilation terms of area of wall/slab openings required to provide
Desired ventilation rates in the kitchens depend upon adequate ventilation. The value applicable is 2.5
percent to 5 percent of the floor area for free opening.
the type of equipment in use and the released impurity
loads (including surplus heat). Ventilation Standards It is necessary to ensure at planning stage itself that
set up the guide lines for ventilation volumes, whereas adequate head room is available in the car parks for
surplus heat and impurity loads determine the actual installing ventilation ducts if such ducting is involved.
airflows based on thermal considerations. The design
for kitchen airflow must allow for sufficient ventilation. 6.5.4 Sizing the Plant

Suggested design standards for exhaust airflows from Sizing the ventilation plant is essentially arriving at the
different kitchen equipment based on their input power air flow rate required. Based on various considerations
are as given in Table 6. already reviewed the sizing of the plant will be
influenced by the following requirements:
Table 6 Design Exhaust Air Flow in I/s per kW
of the Kitchen Equipment a) Removal of sensible heat,
b) Removal of latent heat,
(Clau~e 6.5.2)
c) Make-up air — the flow rate required will
sl Kitchen Equipment Electricity Gas based
depend upon local exhaust, and
No. based Equipment
Equipment d) Removal or dilution of the contaminants
(1) (2) (3) (4) down to the permissible level.

O Cookingpot 8 12 The air flow rate arrived at will be the maximum of


ii) Pressurecookercabinet 5 —
— the flow rates calculated for the above requirements.
iii) Convectionoven 10
iv) Roastingoven (salamander) 33 33 6.5.4.1 Ventilation plant size is often expressed in
v) Griddle 32 35
vi) Fryingpan 32 35 terms of number of air changes per hour or cmh/m2 of
vii) Deep fat fryer 28 floor area. These expressions fail to evaluate the actual
viii) Cooker/stove 32 G heat release provided by the plant. The unit, cmh/m2
ix) GriU 50 61
x) Heatedtable/batb 30 — gives a relationship which is independent of the
xi) Coffeemaker 3 — building height. This is a more rational approach than
xii) Dish wmher 17 — speaking in terms of air changes per hour. This is
xiii) Refrigerationequipment 60 —
xiv) Ceramiccooker/stove — because, with the same internal load, the same amount
25
xv) Microwaveoven 3 — of ventilation air, properly applied to the work zone
xvi) Pizza oven 15 — with adequate velocity, will provide the desired heat
xvii) Inductioncooker/stove 20 .
relief quite independently of the ceiling height of the
space, with few exceptions. Ventilation rates of 30 to
It is desirable to use compensating exhaust hoods for
60 m3/h per m2 have been found to give good results
kitchen equipment installed within air conditioned
in many plants. Notwithstanding these general
spaces. The ventilation rates may be confirmed from
observations, detailed design should be based on
the kitchen equipment supplier.
detailed thorough calculations after all necessary data
6.5.3 Car Parking Ventilation has been evaluated and relevant considerations have
been reviewed.
Ventilation is essential, in car parking areas to take
care of pollution due to emission of carbon monoxide,
6.6 Evaporative Cooling
oxides of nitrogen, presence of oil and petrol fumes
and diesel engine smoke. These contaminants cause 6.6.1 Evaporative cooling is, defined as the reduction
undesirable effect like nausea, headache, fire hazards, of air dry-bulb temperature by the evaporation of
if applicable permissible limits for each of the water.
contaminants noted are exceeded. Although four
6.6.2 When water evaporates into the air to be cooled,
contaminants are listed above, the capacity of a system
simultaneously humidifying it, the process is called
designed to tackle concentration of carbon monoxide,
direct evaporative cooling. When the air to be cooled
will be adequate to keep the other three contaminants
is kept separate from evaporation process, and therefore
also within their respective permissible limits.
is not humidified as it is cooled, then the process is
The recommended ventilation rate will ensure that the called indirect evaporative cooling.
CO level will be maintained within 29 mg/m3 with peak
It is good practice to use 100 percent fresh air in
levels not to exceed 137 mg/m3.
the evaporative cooling. Re-circulation is not
For partially open garages, the requirement is stated in recommended, as it will lead to continuous increase in

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 33
wet-bulb temperature of the air. When evaporative the dry air from the wet surface, Higher face. velocity
cooling is provided for comfort application, it maybe may provide insufficient air-water contact time.
supplemented by devices like ceiling fans and fan
6.6.7 Pad material should be such which provides
coolers to enhance air movement for circulation of air
maximum clean wet surface area with minimum
in internal areas in order to maximize evaporation of
airflow resistance. Materials, which have either good
moisture from the skin.
‘wick’ characteristics or surface that spread water
6.6.3 The geographic range for the evaporative cooling rapidly by capillary action, should be selected.
is based on cooler’s ability to create or approximate
6.6.8 In the ducted systems, all supply air diffusers,
human comfort and is limited by relative humidity in
grilles and registers should be preferably adjustable.
the atmosphere. It is more effective in dry climates
(hot-dry climate zone) where wet-bulb depression is 6.6.9 General room cooling should be supplemented
comparatively large. Factors to be considered — with spot cooling in the hot workplaces.
include those listed in 6.5.4; In addition the following
6.6.10 Reference may also be made to good practice
also apply:
[8-3(5)].
a) Saturation efficiency of the cooler — higher
the better; 6.7 Planning

b) Ambient weather design data; 6.7.1 Planning of Equipment Room for Ventilation
c) Permissible temperature rise; and 6.7.1.1 In selecting the location of equipment room,
d) Type of cooling application — residentid, aspects of efficiency, economy and good practice
industrial, etc. should be considered and wherever possible, it shall
6.6.4 The cooling load control, especially for industrial be made contiguous with the building. This room shall
application shall be carried out in the following manner be located as centrally as possible with respect to the
for effective evaporative cooling: area served and shall be free from obstructing columns.

a) Minimize external heat loads by shading, use Proper location helps achieve satisfactory air
of heat reflective paints, roof insulation and distribution and also results in a less expensive
sealing of gaps. installation.

b) Minimize internal heat loads by shielding, use 6.7.1.2 Equipment room should preferably be located
of reflective paints, insulation and installation adjacent to external wall to facilitate equipment
of exhaust fans over the hot processes and movement and ventilation. It should also close to main
machines. electrical panel of the building, if possible, in order to
c) Make building tight. avoid large cable lengths.
d) Wherever possible, exhaust of used washed 6.7.1.3 Location and dimensions of shafts, for ducting,
air must b; directed towards roof to partly cables, pipes, etc (if envisaged), should be planned at
cool the surface and trusses thereby reducing the virtual stages itself if planning. They should be
heat radiation. located adjacent to the equipment or within the room
6.6.5 Two types of water distribution systems maybe itself.
provided: Evaporative cooling units (air washers) should be
a) Once through or pump-less type. located preferably orr summer-windward side. They
should be painted white or with reflective coating or
b) Recirculating or pump type.
thermally insulated, io as to minimize solar heat
,/
The first type is simpler and cheaper but consumes absorption.
more water, needs constant drainage and has lower
In locating the units, care should be taken to ensure
efficiency depending upon the temperature of water.
that their noise level will not be objectionable to the
The second type has higher cooling efficiency due to
neighbors. Appropriate acoustic treatment should be
recirculate water approaching wet-bulb temperature
considered, if the noise levels cannot be kept down to
conserves water and can operate with intermittent
permissible limits.
drainage. It is recommended to provide periodic bleed-
off or blow down to remove accumulated mineral Exhaust air devices, preferably to leeward and
additions. This helps in reducing scaling of pads also. overhead side may be provided for effective movement
of air.
6.6.6 The air velocity across wetting pad is
recommended between 1.0 and 1.5 m/s. The lower face In the case of large installations it is advisable to have
velocity reduces evaporation as damp air film isolates a separate isolated equipment room if possible.

34 NATIONAL BUILDING CODE OF INDIA


The equipment room should be adequately dimensioned 6.7.1.11 Outdoor air intakes and exhaust outlets shall
keeping in view the need to provide required movement be effectively be shielded from weather and insects.
space for personnel, space for entry and exit of ducts,
6.7.1.12 In all cases air intakes shall be so located as
the need to accommodate air intakes and discharge,
to avoid contamination from exhaust outlets or to from
operation, maintenance and service requirements.
sources whose contamination concentration levels are
6.7.1.4 The floors of the equipment rooms should be greater than normal in the locality in which the building
light coloured and finished smooth. For floor loading, is located.
the air conditioning, heating and ventilation engineer 6.7.1.13 Supply/Return air duct shall not be taken
should be consulted (see also Part 6 ‘Structural Design, through emergency fire staircase. However, exception
Section 1 Loads, Forces and Effects’). can be considered if fire isolation of ducts at wall
Arrangements for draining the floors shall be provided. crossings is carried out.
The trap in floor drain shall provide a water seal 6.7.1.14 Where necessary, structural design should
between the equipment room and the drain line. Water avoid beam obstruction to the passage of supply and
proofing shall be provided for floor slabs of equipment return air ducts. Adequate ceiling space should be made
rooms housing, evaporative cooling units. available outside the equipment room to permit
6.7.1.5 Supporting of pipe within equipment rooms installation of supply and return air ducts and fire
spaces should be normally from the floor. ,However, dampers at equipment room wall crossings.
outside Equipment room areas, structural provisions 6.7.1.15 Access doors to Equipment rooms should be
shall be made for supporting the water pipes from the through single/double leaf type, air tight, opening
floor/ceiling slabs. All floor and ceiling supports make- outwards and should have a sill to prevent flooding of
up and drain connections pipes, ducting cableslcable adjacent occupied areas.
trays etc, shall be isolated from the structure to prevent
6.7.1.16 It should be possible to isolate the equipment
transmission of vibrations.
room in case of fire. The door shall be fire resistant.
6.7.1.6 Plant machinery in the plant room shall be Fire/smoke dampers shall be provided in supply/return
placed on plainlreinforced cement concrete foundation air duct at air handling unit room wall crossings and
and provided with anti-vibratory supports. All the annular space between the duct and the wall should
foundations should be protected from damage by be fme sealed using appropriate fire resistance rated
providing epoxy coated angle nosing. Seismic material.
restraints requirement may also be considered.
6.7.2 In the planning stages itself, provision should
6.7.1.7 Wherever necessary, acoustic treatment should be made for the following (if they are envisaged):
be provided in plant room space to prevent noise
transmission to adjacent occupied areas. a) Space/routing/supports, etc for ducting; and
b) Openings in walls, slabs, roof etc, for passage
6.7.1.8 In case the equipment is located in basement,
of ducts, pipes, cables, etc, and for air intake,
equipment movement route shall be planned to
air exhaust, etc.
facilitate future replacement and maintenance. Service
ramps or hatch in ground floor slab should be provided 6.7.3 Bleed-off and chemical water treatment,
in such cases. Also arrangements for floor draining depending on quality of water available for make-up,
should be provided. should be planned.
The trap in floor drain shall provide a water seal 7 UNITARY AIR CONDITIONER
between the equipment room and the drain line.
7.1 These are self-contained air conditioning units
6.7.1.9 In the case of large and multi-storied buildings, comprising a compressor and evaporator with fans for
independent Ventilation/Air Washer Units should be evaporator and air-cooled condenser. Unitary air
provided for each floor. The area to be served by the conditioners are generally installed in windows and,
air-handling unit should be decided depending upon therefore, they are also known as window air
the provision of fire protection measures adopted. The conditioners. It is designed to provide free delive~ of
Units should preferably be located vertically one above conditioned air to an enclosed space, room or zone. It
the other to simplify location of pipe shafts, cable includes a prime source of refrigeration for cooling
shafts, drainers. and dehumidification and means for circulation and
6.7.1.10 Openings of adequate size should be provided filtration of air. It may rdso include provision to exhaust
for intake of fresh air. Fresh air intake shall have room air as also induce fresh air for ventilation in the
louvers having rain protection profile, with volume room. In addition to basic cooling unit, there are several
control damper and bird screen. other optional features available, such as:

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 35
a) Means for heating during winter months. 7.6 Location
b) Reciprocating or rotary compressor.
Unitary air conditioners should be mounted preferably
c) Swing louvers for better distribution of air in at the window sill level on an external wall where hot
the room. air from air-cooled condenser may be discharged
d) In addition to normal, dust filters, indoor air without causing nuisance. There should not be any
quality filters, such as bactericidal enzyme obstruction to the inlet and discharge air of the
filters for killing bacteria, low temperature condenser. Also while deciding location of the window
catalyst filter for removal of unpleasant air conditioners, care should be taken to ensure that
odours, electrostatic filters to trap particles the condensate water dripping does not cause nuisance.
of smoke as well as suspended matters present The opening for the air conditioner is generally made
in the air. apart of windows or wall construction at the planning
e) Digital LCD remote control which also stage.
indicates room temperature.
7.7 Limitations
7.2 Capacity Room air conditioners are not generally recommended
Most of the manufacturers supply unitary air conditions in the following situations:
in capacities of 3500 W (1 TR), 5250 W (1.5 TR) and
a) The width of the area exceeds 6 m.
7000 W (2 TR). However, some of them may be able
b) Area requiring close control of temperature
to supply window air conditioners of 1750 W (0.5 TR)
and relative humidity.
and upto 10500 W (3 TR) alongwith intermediate
range. The capacity of windows air conditioners is c) Internal zones where no exposed wall is
rated at outside dry bulb temperature of 35°C and wet available for the installation of room air
bulb temperature of 30”C and they are suitable for conditioners.
230 V, single phase 50 Hz power supply. Nominal d) Sound recording rooms where criteria for
capacity of all the window air conditioners has to be acoustics are stringent.
de-rated due to high ambient temperatures in summer e) Special applications like sterile rooms for
months in most of Indian cities. Also, generally a hospitals and clean room applications where
voltage stabilizer has to be installed to ensure that high filtration efficiency is desired. b
window air conditioner gets stabilized rated voltage. f) Operation theatres where 100 percent fresh
air is needed and fire hazard exists depending
7.3 Suitability
on the type of anaethesia being used.
Unitary air conditioners are suitable for bedrooms, g) Where required to comply with the
office cabins, general office area, hotel rooms and recommended fresh air requirement for
similar applications where normal comfort conditions ventilation.
are required upto a distance of 6 m from unitary air
7.8 For detailed information regarding constructional
conditioner.
and performance requirements and methods for
7.4 Power Consumption establishing ratings of room air conditioners, reference
may be made to accepted standard [8-3(6)].
Power consumption of window air conditioners
of 1 TR (3 500 W) rated capacity should not exceed 8 SPLIT AIR CONDITIONER
1.55 kW/TR. However, in smaller sizes, the power
8.1 Split air conditioner has an indoor unit and an
consumption may exceed. Rotary compressors
outdoor unit interconnected with refrigerant piping and
normally consume 7 percent to 8 percent less power
power and control wirin& Indoor unit comprises of a
compared to the above value for reciprocating
filter, evaporator and evaporator fan for circulation of
compressors.
air in the conditioned space. Outdoor unit has a
7.5 Noise Level compressor, air-cooled condenser with condenser fan
housed in a suitable cabinet for outdoor installation.
Noise level of window air conditioner inside the
Split air conditioner includes primary source of
conditioned room should be as low as possible. refrigeration for cooling and dehumidification and
However it should not exceed 65 dBA for 5250 W means for circulation and cleaning of air, with or
(1.5 TR) or smaller capacity window air conditioners.
without external air distribution ducting.
Air conditioners with rotary compressors will have
lower noise level as compared to those provided with Split air conditioners may be provided with either
reciprocating compressors. reciprocating compressor or scroll compressor. Scroll

36 NATIONAL BUILDING CODE OF INDIA


compressor generally consumes about 10 to 12 percent 8.5 Installation
less power compared to reciprocating compressor.
Ceiling suspended indoor units are provided with
Various split air conditioners available may be rubber grommet to reduce vibration. Outdoor units are
categorised as under mounted on a steel frame in an open area so that the
fan of the air cooled condenser can discharge hot air
a) Exposed indoor unit, which is either a high
to the atmosphere without any obstruction. Care should
wall unit or a floor-mounted unit.
be taken to ensure that free intake of air is available to
b) Furred-in units (ceiling suspended unit), the outdoor air cooled condenser. Also precaution
which is mounted in the ceiling and provided should be taken that hot air from any other outdoor
with a duct collar and grille. unit does not mix with the intake of the other outdoor
c) Ducted indoor unit, which requires ducting air cooled condenser.
for air distribution.
8.6 Limitations
8.2 Suitability Split air conditioners are generally not recommended
Split air conditioners are suitable for wide range of for:
applications including residences, small offices, clubs, a) For areas where fresh air is required for
restaurants, showrooms, departmental stores, etc. ventilation.
b) Where distance between indoor exposed unit
8.3 Capacity
or fiwred-in unit exceeds 5 m from the outdoor
Split air conditioners are available in following unit for units up to 7000 W (2 TR) capacity.
capacities: For larger ducted split air conditioners, the
vertical distance between the indoor unit and
a) Indoor exposed units, 3500 W (1 TR),
the outdoor unit should not exceed about 6 m
5250 W (1.5 TR), 7000 W (2 TR) or two
for units with reciprocating compressors. The
indoor units of 3500 W (1 TR) or 5250 W
horizontal distance between the indoor unit
(1.5 TR), connected with one outdoor unit of
and outdoor unit should not exceed about
7 000W(2TR)or10500 W (3 TR) capacity.
10 m for reciprocating compressors.
These units are available with corded and
cordless remote control. c) Area requiring close control of temperature
and relative humidity.
b) Furred-in Units are available in capacities of
3 500W (1 TR) and 5 250W (1.5 TR) and d) Sound recording rooms where criteria for
may be provided with one outdoor unit or two acoustics are stringent.
outdoor units with two furred-in indoor units. e) Special applications like sterile rooms for
These units are available with corded and hospitals and clean room applications where
cordless remote control. high filtration efficiency is desired.
c) Ducted split air conditioners (ceiling f) Large muki-storey buildings where multiplicity
suspended ducted units) are available in of the compressors may entail subsequent
capacities of 10500 W (3 TR), 17500 W maintenance problems.
(5 TR), 26250 W (7.5 TR) and 52500 W g) Where the length of air distribution ducting
(15 TR). Ducted split air conditioners may exceed about 20 m.
with scroll compressors are available
8.7 Reference may be made to accepted standard
in sagacities of 19250 W (5,5 TR) and
[8-3(7)].
29750 W (8.5 TR).

8.4 Location 9 PACKAGED AIR C~DITIONER

Split air conditioner indoor unit is mounted within the 9.1 Packaged air conditioner is a self-contained unit
air conditioned space or above the false ceiling from primarily for floor mounting, designed to provide
where the air distribution duct is taken to the conditioned air to the space to be conditioned. It
conditioned space to distribute the air. When the indoor includes prime Source of refrigeration for cooling fid
dehumidification and means for circulation and
unit is mounted in the false ceiling, inspection panel
cleaning of air, with or without external air distribution
must be kept in the false ceiling to attend to the indoor
ducting. It may also include means for heating,
unit including periodic cleaning of air filter. Outdoor
humidifying and ventilating air.
unit is mounted at the nearest open area where
unobstructed flow of outside air is available for air The unit comprises a compressor, condenser and
cooled condenser. evaporator, which are interconnected with copper

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 37
refrigerant piping and refrigerant controls. It also taken to the conditioned space. While deciding location
includes fan for circulation of air and falter. The unit is for the packaged unit, provision must be kept for proper
provided with compressor and fan motor starter and servicing of the unit.
factory-wired safety controls.
9.5 Installation
Compressor is a device, which compresses low-
The packaged units are normally mounted on a resilient
pressure low temperature refrigerant gas to high-
pad which prevents vibration of the unit from being
-pressure high temperature super heated refrigerant gas.
transmitted to the building.
Compressors may be reciprocating type or scroll type
for packaging unit applications. 9.6 Limitations

Condenser condenses high pressure high temperature Packaged air conditioner are not generally recommended
refrigerant gas to liquid refrigerant at approximate y for:
the same temperature and pressure by removal of
a) Large multi-storey buildings where multiplicity
sensible heat of refrigerant by external means of water
of the compressors may entail subsequent
cooling or air cooling.
maintenance problems.
The packaged units are also available with b) Where the length of air distribution ducting
microprocessor-based controller installed in the unit may exceed approx 20 m.
for digital display of faults as also several other
c) Where the vertical distance of air-cooled
functions. The packaged unit can also be provided with
condenser from the packaged unit exceeds
winter heating package or humidification package. The
about 10 m. The sum of horizontal and vertical
packaged unit may be provided with either water-
distances should be generally kept within 15 m.
cooled condenser or a remote air cooled condenser with
d) Special applications like sterile rooms for
interconnected copper refrigerant piping. The units are
hospitals and clean room applications where
available with reciprocating compressor as also scroll
high filtration efficiency is desired.
compressor, which consume about 10 to 12 percent
lesser power. In a water-cooled condenser unit, e) Operation theatres where 100 percent fresh
condenser-cooling water is circulated through the air is needed and fire hazard exists depending
cooling tower with necessary piping and pumpsets. on the type of anesthesia being used.

The water cooled condenser packaged unit gives higher 9.7 For detailed information regarding constructional
capacity at lower power consumption as compared to and performance requirements and methods for
an air cooled condenser packaged unit which gets establishing ratings of packaged air conditioners,
considerably de-rated in capacity and also consumes reference may be made to accepted standard [8-3(8)].
more power in peak summer months in most of the
10 HEATING
cities of our country due to high ambient temperature.
10.1 The installations for air conditioning system may
Packaged units are generally available with vertical
be used advantageously for,the central heating system
air discharge or horizontal air discharge.
with additions such as hot water or boiler and hot water
9.2 Suitability coils or strip heater banks.

Packaged units are suitable for wide range of 10.2 The heating equipments as described in 10.2.1
applications including offices, clubs and restaurants, and 10.2.2 are generrdly used:
showrooms and departmental stores, and computer 10.2.1 Hot Water Heated Coils
rooms, etc.
Central heating systems” using hot water usually
9.3 Capacity required not more than one or two rows of tubes in the
Normally the packaged air conditioners are manufactured direction of air flow, in order to produce the desired
in sizes of 17500 W (5 TR), 26250 W (7.5 TR), heating capacity. To achieve high efficiency without
35000 W (10 TR) and 52500 W (15 TR). Packaged excessive water pressure drop through the coil, various
units with scroll compressors are also available in circuit arrangements are used.
capacity up to 58100 W (16.6 TR). Generally, the resistance to the hot water flow through
the heater should not exceed 4 IcPa in low pressure hot
9.4 Location
water heating installations. In high pressure hot water
The packaged unit can be mounted within the air installations, the resistance to the water flow will
conditioned space with discharge air plenum or in a probably be determined by other factors, for example,
separate room from where the air distribution duct is the need to balance circuits.

38 NATIONAL BUILDING CODE OF INDIA


F--

The heaters should be served from hot water flow and ventilation and refrigeration system shall be in
return mains with sufficient connections to each row accordance with good practice [8-3(9)].
or bank of tubes or sections to give uniform distribution
11.2 Colour code for identification for various items
of the heating medium.
in air conditioning installations for easy interpretation
The flow connections to the heater should generally and identification is advisable. This shall promote
be arranged at the lowest point of the heater, and the greater safety and shall lessen chances of error,
return connections at the highest, to aid venting. The confusion or inaction in times of emergency< Colour
expansion of the tubes when the heater is in operation shade shall be generally in accordance with good
should be considered and the necessary arrangements practice [8-3(10)].
made to accommodate expansion and contraction.
11.3 Colour bands shall be 150 mm wide,
Thermometer wells should be fitted in the pipes near superimposed on ground colour to distinguish type
the inlets and outlets of all air-heating coils so that the and condition of fluid. The spacing of band shall not
temperature drop through the heater can be readily exceed 4.0 m.
observed.
11.4 Further identification may also be carried out
10.2.2 Electric Air Heater using lettering and marking direction of flow.

The air velocity through the heaters should be sufficient 11.5 Services Identification
to permit the absorption of the rated output of the finned
tube heaters within its range of safe temperatures and 11.5.1 Pipe Work Services
the exact velocity determined in conjunction with the 11.5.1.1 The scheme of colour code for painting of
manufacturers of the heater. Electrical load should be pipe work services for air conditioning installation shall
balanced across the three-phase of the electrical supply. be as indicated in Table 7.
Where automatic temperature control is required 11.5.1.2 In addition to the colour bands specified
the heater should be divided into a number of above, all pipe work shall be legibly marked with black
sections dependent upon the degree of control to be or white letters to indicate the type of service and the
effected. direction of flow, identified as follows:
Each section of heater elements, which may be two High Temperature Hot Water HTHW
rows of elements should have its own busbars and MTHW
Medium Temperature Hot Water
connection and be capable of withdrawal from the
Low Temperature Hot Water LTHW
casing, thus enabling the elements to be cleaned or
Chilled Water CHW
repaired whilst the remainder is in operation. Each
Condenser Water CDW
section should be capable of being isolated electrically
before being withdrawn from the casing. Steam ST
Condensate CN
All heaters should be electrically interlocked with the
fan motors, so that the electric heater will be switched 11.5.2 Duct Work Services
off when the fan is stopped or when the air velocity is
11.5.2.1 For duct work services and its insulation,
reduced to a level below that for which the heater has
colour triangle may be provided. The size of the
been designed.
triangle will depend on the size of the duct and viewing
The air velocity over the face of the heater is of distance but the minimum size should not be less than
particular importance in the design of electric air 150 mm length per side.
heaters, and the manufacturers should be given details
The colour for various duct work services shall be as
of the maximum and minimum air velocities likely to
given below:
occur.

With all electric air heaters, care should be taken to Services Colour
preclude the risk of fire under abnormal conditions of Conditioned Air Red and Blue
operation, by the use of a suitably positioned Ward Air Yellow
temperature sensitive trip of the manual reset type to Green
Fresh Air
cut off the electric supply. Grey
Exhaust/Extract/Recalculated Air
11 SYMBOLS, UNITS, COLOUR CODE AND Foul Air Brown
IDENTIFICATION OF SERVICES Dual Duct System Hot Supply Air Red
Cold Supply Air Blue
11.1 Units and symbols to be used in air conditioning,

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 39
2
,
% ,
*
. .
*.*

Table 7 Scheme of Colour Code of Pipe Work Services for Air Conditioning Installation
(Clause 11.5.1.1)

S1 No. Description Ground Colour Lettering Colouring First Colour Band


(1) (2) (3) (4) (5)

i) Cooling water Sea green Black French blue


ii) Chilled water Sea green Black Black
iii) Central heating below 60”C Sea green Black Canary yellow
iv) Centml heating 60”C to 100”C Sea green Black Dark violet
v) Drain pipe Black White
vi) Vents White Black
vii) Valves and pipe line fittings White with black handles Black
viii) Belt guard Black yellow diagonal strips
ix) Machine bases, inertia bases and plinth Charcoal grey

11.5.3 Valve Labels and Charts determined by the manner in which the building and
its services are used and is measured in units of energy
Each valve shall be provided with a label indicating
(Wh/m2). Targets may be established according to
the service being controlled, together with a reference
number corresponding with that shown on the Valve varyj ng climatic conditions and varying pattern of
Charts and ‘as fitted’ drawings. ‘The labels shall be building use.
made from 3 ply (black/white/black) traffolyte
12.3.4 Air Conditioning/Ventilation
material showing white letters and figures on a black
background. Labels shall be tied to each valve with Some of the more important aspects of establishing
chromium plated linked chain. energy conservation requirements for air conditioning
and ventilation system are given below.
12 ENERGY CONSERVATION, ENERGY
MANAGEMENT, AUTOMATIC CONTROLS 12.3.5 The design of the system and its associated
AND BUILDING MANAGEMENT SYSTEM controls should take into account the following:

12.1 In the context of this Code, energy conservation a) The nature of the application;
signifies the optimum use of energy to operate the air b) The type of construction of building;
conditioning, heating and ventilation system of a building. c) External and internal load patterns;
d) The desired space conditions;
12.2 It is axiomatic that general standards of comfort
or specific environmental requirements within the e) Permissible control limits;
building should not be compromised in an endeavour f) Control methods for minimizing use of
to achieve lower consumption of energy. Similarly primary energy;
nothing in this Code overrides regulations related to Opportunities for heat recovery;
g)
health and safety.
h) Economic factors (including probable future
12.3 Considerations for Energy Conservation and cost and availability of fuel).
Management j) Opportunity for optimizing electrical installation
and energy conservation by using thermal
12.3.1 Energy Targets
energy storage.
For the purpose of assessing energy conservation
12.3.6 The operation of the system for the following
efficiency of one system design against another, or in
conditions has to be considered when assessing the
an existing building comparing one period of energy
use against another, target consumption may be complete design:
established. a) in summer;
12.3.2 Demand Targets b) in winter;

Energy demand is mainly determined by location of c) in intermediate seasons;


the building, its structure and the equipment installed d) at night;
within it. Demand targets are readily applied to designs e) at weekends; and
for new buildings and are quoted as an ‘average rate’ f) restoration of power supply after intermittent
of energy use (W/m2). failure.
12.3.3 Consumption Targets 12.3.7 Consideration should be given to changes in
The energy actually consumed in a building is building load in the system design so that maximum

40 NATIONAL BUILDING CODE OF INDIA


operational efficiency is maintained under part The basic components of a control system are:
load conditions. Similarly, the total system should
be separated into smaller increments having Element or Component Function
similar load requirements so that each area can be Sensing and measuring Measuring changes in
separately controlled to maintain optimum operating element of the controller one or more controlled
conditions. (for example, sensor, conditions or variables.
transmitters, transducers,
12.3.8 The temperature of heating or cooling media
meters, detector)
circulated with in the system should be maintained at
Controller mechanism Translating the changes
the level necessary to achieve the required output to
into forces or energy of a
match the prevailing load conditions with the minimum
kind that can be used by
consumption of energy.
the final control element.
12.3.9 Energy recovery has to be maximized. Connecting members of Transmitting the energy
the control circuit wiring or forces from the point
12.3.10 Operation and maintenance procedures have
for electric linkages for of translation to the point
to be properly planned. of corrective action.
mechanical devices
12.3.11 Equipment Consideration Controlled devices or Using the force or energy
actuator such as motor to motivate the final
12.3.11.1 All equipment and components should be or valve control element and effect
tested in accordance with the relevant Indian Standards; a corrective change in the
where no applicable standard exists, an agreed controlled condition.
international or other standard and test procedure may Controller mechanism, Terminating the call for
be adopted. comecting means, and corrective change, to
actuator or control device prevent over-correction.
12.3.11.2 The equipment suppliers should furnish
upon request the energy input and output of the
equipment, which should cover full and partial loads 12.5.2 Sensing and Measuring Elements
and standby conditions as required in order that the 12.5.2.1 Temperature elements
energy consumption can be assessed over the whole
range of operating conditions. a) A bimetal element comprises two thin strips
of dissimilar metals fused together and
12.3.11.3 Where components from more than one arranged as a straight, U-shaped or spiral
supplier are used in combination, for which published element. The two metals have different
performance data do not exist then the system designer coei%cients of thermal expansion, so a change
should take the responsibility for ensuring that their in temperature causes the element to bend and
combination leads to optimum energy use. produce a change in position.
12.3.11.4 Equipment preventive maintenance schedule b) A rod and tube element is composed of a high
should be furnished along with all other required expansion metal tube inside which is located
information. a low expansion rod with one end fixed to
the rear of the tube so that temperature
12.4 Control System changes cause the free end of the rod to move.
c) Sealed bellows element is evacuated of air and
The designer should aim to select the simplest system
charged with a liquid, gas O! vapour, which
of control capable of producing the space conditions
changes in pressure or volume as surrounding
required. It is uneconomical to provide controls with a
temperature changes to result in change of
degree of accuracy greater than the required by the
force or movement.
application. Consideration should be given to the
d) Remote bulb element consists of a sealed
provision of centralised monitoring and control, thus
bellows or diaphragm to which a bulb or
achieving optimum operation.
capsule is attached by means of capillary
12.5 Automatic Controls and Building Management tubing, the entire system being filled with
System liquid, gas or vapour. Temperature changes
at the bulb are communicated as pressure or
12.5.1 Types of Equipment volume changes through the capillary tube to
The basic components that are designed, selected to the bellows or diaphragm.
work together to form a complete control system, e) Resistance temperature detectors (RTDs) are
together with their function, are shown as follows: temperature sensors containing either a fine

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 41
wire or a thin metallic element whose ventilating systems, for example a ‘paddle-
resistance increases with temperature and blade’ type of air flow switch may be
varies in a known manner. RTDs are interlocked with an electric heater battery
characterised by their high degree of linearity, to prevent battery from operating and
good sensitivity and excellent stability. RTDs overheating in the event of an air flow failure.
are used with electronic controllers. b) Other elements employed from time-to-time
f) Thermocouple element comprises a junction are measuring smoke density, carbon monoxide
between two dissimilar metals that generates (for example in road traffic tunnels or
a small voltage related to the temperature. underground car parks) and carbon dioxide,
and for flame detection.
12.5.2.2 Humidity devices
12.5.2.5 Controllers
a) These devices have a hydroscopic organic
polymer deposited on a water permeable Controlling elements normally regulate the application
substrate. The polymer film absorbs moisture of either electrical or pneumatic energy. Controllers
until it is in balance with the ambient air. This are mainly of three types: thermostat, humidistats and
causes a change in resistance or capacitance. pressure controllers.
b) Resistance elements, as employed in electronic
12.5.2.6 Thermostats
systems, consist usually of two interleaved
grids of gold foil, each connected to a terminal The following types of thermostats are in common use:
and mounted on a thin slab of insulating
a) The room type responds to room air temperature
plastic material with a coating of hydroscopic
and is designed for mounting on a wall.
salt (lithium chloride) on the block. A
b) The insertion thermostats respond to the
conductive path between adjacent strips of foil
temperature of air in a duct and are designed
is formed, and the high electric resistance of
for mounting on the outside of a duct with its
this circuit changes as the chemical film
measuring element extending into the air
absorbs and releases moisture with changes
stream.
in the relative humidity of surrounding air.
c) The immersion type responds to the temperature
12.5.2.3 Pressure elements of a fluid in a pipe or tank is designed for
a) Low-pressure measuring elements for low mounting on the outside of a pipe or tank
positive pressure or for vacuum conditions, with a fluid-tight connection to allow the
for example, static pressure in an air duct, measuring element to extend into the fluid.
usually comprise a large slack diaphragm, or d) The remote bulb thermostat is used where the
large flexible bellows. In one type of static point of temperature measurement is some
pressure regulator two bells are suspended distance from the desired thermostat location,
from a lever into a tank of oil, so that positive which may often be in central panel. A
pressure under one of the bells moves the bell differential type employing two remote bulbs
and lever up (or down) to complete an electric may be used to maintain a given temperature
circuit. The majority of these elements sense difference between two points.
differential pressure, and when combined e) The surface type is designed for mounting on
with pitot tubes, orifice plates, and venturi a pipe or similar surface and measuring its
meters may be used to measure velocity, flow temperature, or to give an approximate
rate or liquid level. measurement of temperature of the fluid with
b) High-pressure measuring elements, for in the pipe.
pressure or vacuum measurements in the kPa f-) The day/night room thermostat is arranged to
range, are usually of bellows, diaphragm or control at a reduce temperature at night, and
Bourdon tube type. If one side of the element may be changed from day to night operation
is left open to atmosphere the element at a remote point by hand or time clock, or
will respond to pressure above or below from a time switch built into the thermostat
atmospheric. itself.
g) The heating/cooling (or summer/winter)
12.5.2.4 Special elements
thermostat can have its action reversed and,
a) Special elements for various measuring or where required, its set points raised or lowered
detecting purposes are often necessary for by remote control. This type of thermostat is
complete control in air conditioning or used to actuate controlled devices, such as

42 NATIONAL BUILDING CODE OF INDIA


valves or dampers, that may regulate a heating 4) Low flow valves may be as small as
medium at one time and cooling medium at 3 mm port size and are used for accurate
another. control of low flow rates.
h) The multi-step thermostat is arranged to 5) Three way mixing valves have two inlets
operate in two or more successive steps. and one outlet, and operate to vary the
j) A master thermostat measures conditions at proportion of fluid entering each of the
one point of another (sub-master) thermostat two inlets<
or controller. 6) Three way diverting valves have one inlet
and two outlets and operate to divert or
12.5.2.7 Humidistats
proportion the inlet flow to either of the
Humidistats may be of the room or insertion type. For two outlets.
example, a sub master room humidistat may be used 7) Two way modulating valves have one
with an outdoor master thermostat to reduce humidity inlet and one outlet and operate to
in cold weather and prevent condensation on windows. modulate or proportion the flow through
A wet-bulb thermostat is often used for accurate the heat exchange equipment.
humidity control, working in conjunction with a dry
8) Butteffly valves comprise a heavy ring
bulb controller.
enclosing a disc that rotates on an axis at
12.5.2.8 Pressure controllers or near its centre and may be used for
shut-off where low differential pressures
Pressure or static pressure controllers are made for
exist.
mounting directly on a pipe or duct. The controller
9) Special multi-port valves for various type
may also be mounted remotely on a panel.
of modulatinglsequences operation are
12.5.2.9 Controlled devices available for control of both hot and
12.5.2.9.1 Automatic control valves chilled water to three and four pipe fan
coil and induction unit systems.
An automatic control valve consists of a valve body to
b) Valve operators — Valve operators usually
control the flow of fluid passing through it by use of a
comprise an electric solenoid, electric motor,
variable orifice that is positioned by an operator in
or pneumatic actuator, brief details of which
response to signals from the controller. The fluid
are given below:
handled is generally steam or water, and the operator
1) A solenoid is a magnetic coil that
is usually of the electric motor or pneumatic actuator
operates a movable plunger to provide
type. As 75 percent or more of all air conditioning and
two-piston operation.
mechanical ventilation systems utilize a valve of some
sort as the final control element, proper control valve 2) An electric motor is arranged to operate
selection is one of the most important factors in the valve stem through a gear train and
attaining good systems performance. linkage. Various types are available for
different applications, such as:
Following are the details of various valve types and
i) A unidirectional motor is used for
valve operators:
two position operation, the valve
a) Valve types — The main type and their opening during one half revolution
characteristics are summarized below: of the output shaft and closing during
1) Single seated valves are designed for the next half revolution.
tight shut-off. ii) A spring return motor for two
2) Double seated valves are designed so that position control operation is energized
the fluid pressure on the two discs is electrically, dri~en to one position,
essential balanced, reducing the power and held there until the circuit is
required to operate; this type of valve broken, when the spring returns the
does not provide a tight shut-off. valves to its normal position.
3) Pilot operated valves utilize the pressure iii) A reversible motor is used for
difference between upstream and floating or proportional operation
downstream sides to act upon a diaphragm and can run in either direction and
or piston to move the valve, and are stop in any position.
usually single seated, for two piston 3) A pneumatic actuator usually comprises
applications only, and used where large a spring opposed flexible diaphragm or
forces are required for valve operation. bellows connected to the vrdve stem, so

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 43
that an increase in air pressure acts on Remote data collection panels or remote enclosure?
the diaphragm or bellows to move the which act as termination points for the remote ends of
valve stem compress the spring. When the transmission links and for connections to the remote
the air pressure is removed the spring will input and output devices.
return the operator to its normal position.
12.5.2.9.5 Transmission links
12.5.2.9.2 Automatic control dampers
The transmission links provides the means for
Control dampers are designed to control the flow of communication between the central equipment and the
air in a ductwork system in much the same as an remote data collection panel and may be classified
automatic valve operates in a fluid circuit, that is by according to a number of variables, which includes:
varying the resistance to flow. Following are the details
a) Medium (wires or cables, telephone lines,
of various damper valves and damper operators:
micro wave);
a) Damper valves b) Transmission mode (one direction only, one
1) The single blade damper is generally direction at a time, etc);
restricted to small sizes since it does not c) Data sequence (series, for 2-wire, parallel for
provide accurate control. When fitted in multi-conductor etc);
circular ductwork it may be referred to
d) Wire or cable types;
as a butterfly damper.
e) Signal types; and
2) A multi-leaf damper is two or more
f) Message format.
blades linked together, which may be:
.,.
i) A parallel action multi-leaf damper, Other considerations include the physical arrangement
having its blades linked so that when of the transmission system, security and supervisory
operated they all rotate in the same aspect.
direction.
12.5.2.9.6 Central equipment
ii) An opposed action multi-leaf damper,
having adjacent blades linked to This may comprise:
rotate in opposite directions when a) An interface, which provides a connection
operated. point and the signal conversion between the
b) Damper operators central processor and transmission links.
These may be electric motors of the b) The central processor, which is the collection
unidirectional, spring return or reversible type of equipment at the central control room
fitted with suitable linkage mechanisms, or containing the logic for management of the
may be pneumatic actuators of a type centralized control and monitoring system;
designed for damper operation. the processor has the means to receive,
transmit and present information, with the
12.5.2.9.3 Centralized controllmonitoring equipment
ability to process all data in an orderly
The centralized control system, which is shown fashion, and may or may not include a
diagrammatically in Fig. 1, comprises three main parts: computer.
the remote location equipment, the transmission links, c) Peripheral devices such as typewriters,
and the central equipment. printers, displays (digital type, projectors, or
12.5.2.9.4 Remote location equipment cathode ray tubes, etc).

This includes: 12.5.3 Selection Factors ,

a) Input devices or sensors, which measure the 12.5.3.1 Common factors


condition of a variable;
There are a number of factors to be considered in the
b) Signal conditioning devices, which convert selection of almost all control system components.
the sensor signal to a type compatible with These common factors include:
the requirements of the remote panel,
transmission system, or the central equipment; a) Supply and working electricity voltage, phase,
frequency and number of wires;
c) Output devices, which provide a means for
converting a command instruction, appearing b) Maximum andor minimum temperatures,
at the remote panel, into a signal suitable for humidities or pressures to which components
performing an operational function on may be subjected;
external equipment; and c) Restrictions or location, mounting positions,

44 NATIONAL BUILDING CODE OF INDIA


(S)3AINCI A3N3nC13&J3
379vlsnrav
3791.LVdWOO
, 4
* 9
1 1
301A3a 30VdN31Nl W31SAS Sdn
M371OMNO3 000 tlOdlEINVd 10UNO3
6 ?
a -
,
lN3Pldlfl133
Nollvlsans
-~--------,
I sL3s 9a
SkiOSN3S
VS1ON1NO39NI1H9I1
W31SAS
9NlN3J.dOS l?lN3WlV3tU
&i31VM w s31mun
SNVdlSnVHX3
‘8SNVdNOllVlllN3A
lNVld
9NlN3.LJOSlIlN3WlV3tll N31VM
SdWnd
0NllH91d 3U13
1 I
33wNollvlL1.N3A
am 9NINO111CIN03 NIV ‘9NILV3H
I I
N01VN3N39
U31VM10HClNVSdWnd L131VM
1 1 M3sN3aNo3wa3” lHo’st13111Hcl
sllNn
9NI1ONVHMV
-J 1 J
●
0..
r-
Cw
u)
m
— g
—
I
m “-
~
~
L
— *
i
)
I
— I
L
PARTS BUILDINGSERVICES—SECTION 3 AIRCONDITIONING,HEATINGANDMECHANICALVENTILATION 45
etc, or possible problems due to duct, approved standards, unless otherwise stated. Approval
vibration etc; at the time of inspection shall not be construed as
d) Dimensions and mass; acceptance unless the equipment proves satisfactory
e) Finish and type of enclosure; and in service after erection.
“)

f) Required accessories or fittings. High pressure air duct system should also be tested in
NOTE — These common factors, should only be used accordance with the procedures.
!
as a general guide, and control manufacturers should
be consulted in establishing exact requirements.
13.2.1 Inspection and Testing at Works

12.5.4 Sensing/Measuring Elements The air conditioning system will consist of various
items of equipment produced by various manufacturers.
Sensing and measuring elements frequently form an Each manufacturer should give facilities for the
integral part of a controller and the selection factors to inspection of his equipment during manufacturing and
be considered for this arrangement may be as given on completion, as specified.
in 12.5.3.1. However, a sensor may be designed and
arranged for operation with a remote controller and 13.2.2 Inspection and Testing on Site
other components, in that case some of the more Prior to commissioning, testing, adjusting and
important selection factors for temperature elements, balancing, preliminary checks and charging of the
for example, may be as follows: complete system should be carried out. It is important
that all water systems should have been thoroughly
a) Control operations, for example reverse or
direct-acting; flushed through and hydraulically pressure tested to
1.5 times the working pressure for a period of not less 7’
b) Sensing range, adjustable or non-adjustable;
than 8 h.
c) Provision for air filter;
d) Pressure output; 13.3 Commissioning, Testing, Adjusting and
e) Provision for branch pressure indication; Balancing

f) Application, for example room, duct or 13.3.1 Basic Considerations


immersion in pipeline;
13.3.1.1 The basic considerations are:
.!3) Application, for example room, duct immersion
in pipeline; a) to test to determine quantitative performance
h) Electronic; of equipment;
Function, for example for primary or secondary b) to adjust to regulate for specified fluid flow
j)
control; rates and air patterns at terminal equipment
(for example reduce fan speed, throttling etc);
k) Temperature range;
and
m) Authority range of throttling range adjustment;
c) to balance to proportion within distribution
n) Nominal resistance and sensitivity; and
system (sub mains, branches and terminals)
P) Provision for temperature indication. in accordance with design quantities.

13 INSPECTION, COMMISSIONING AND 13.3.1.2 The objective of testing, adjusting and


TESTING balancing of air conditioning, heating and mechanical
ventilation system shall be to:
13.1 Inspection, commissioning and testing should be
carried out meticulously if a satisfactory installation is a) verify design conformity;
to be handed over to the client. It should be ensured b) establish fluid ,flow rates, volume and
that these are carried out thoroughly and all results are operating pressties;
properly documented. It is recommended that the c) test all associated electrical panels and
whole commissioning procedure should be under the electrical installation for earthing continuity
guidance and control of a single authority, to be and earth resistance;
identified by the client.
d) take electrical power readings for each
13.2 Inspection and Testing motor;
e) establish operating sound and vibration
All equipment and components supplied may be
levels;
subjected to inspection and tests during manufacture,
erection/installation and after completion. No f) adjust and balance to design parameters; and
tolerances at the time of inspection shall be allowed g) record and report results as per the specified
other than those specified or permitted in the relevant formats.

46 NATIONALBUILDING CODE OF INDIA


13.3.2 System Testing, Adjusting and Balancing c) Check pumps operation for proper rotation
and motor current drawn etc;
13.3.2.1 Refrigeration plant
d) Confirm that provisions for tabulation of
The refrigeration plant may be tested for the measurements (temperature, pressure and
following: flow measurements) have been made; and
a) Adjusting water flow rate through chiller and e) Open all shut-off valves and automatic control
condenser by use of balancing valves. valves to provide full flow through coils. Set
b) Ascertaining the capacity by measurement of all balancing valves in the preset position, if
water flow rate and temperature of water at these values are known. If not, shut all riser
inlet and outlet of chilling machine. balancing valves except the one intended to
be balanced first.
c) Computation of power consumption.
d) Verifying operating noise level as per Balancing work for both chilled water system and
manufacturer instructions. condenser water system shall be carried out in a
professional manner and test reports in the specified
13.3.2.2 Air system format shall be prepared.
13.2.2.2.1 Air handlers performance 13.4 Controls
The testing, adjusting and balancing procedure shall Since most of the control equipment used for air
establish the right selection and performance of the air conditioning system is factory calibrated, hence
handling units with the following results: physical verification before installation shall be carried
a) Air-in dry-bulb and wet-bulb temperature, out. In addition, manufacturers instructions should be
followed for site calibration, if any.
b) Air-out dry-bulb and wet-bulb temperature,
c) Leaving air dew point temperature, 13.5 Noise and Sound Control
d) Fan air volume, Measurements should be taken with a sound level meter
e) Fan air outlet velocity, either using the ‘A’ weighting scale or to draw up a
f) Fan static pressure, noise criteria curve. Measurements should be taken in
the following locations:
g) Fan power consumption,
h) Fan speed, and a) Plant rooms;
j) Check for zero water retention in the b) Occupied rooms adjacent to plant rooms;
condensate drain pan. c) Outside plant rooms facing air intakes and
exhausts and condenser discharge, to assess
13.3.2.2.2 Air distribution
possible nuisance to adjacent occupied
Both supply and return air distribution for each air areas;
handling unit and for areas served by the air handling d) In the space served by the first grille or
unit shall be determined and adjusted as necessary to diffuser after a fan outlet;
provide design air quantities. It shall cover balancing e) In at-least two of the spaces served by fan
of air through main and branch ducts. coil units or high velocity system terminal
units (where applicable);
13.3.2.2.3 Hydronic system
f) In any space; and
The hydronic system shall involve the checking and
@ Air handling unit (AHU) rooms and adjoining
balancing of all water pumps, piping network (main
areas.
and branches), heat exchange equipment like cooling
and heating coils, condensers, chillers and cooling 13.6 Handover Procedure
towers in order to provide design water flows. Handover documentation should contain all
The essential preparation work, shall be done by the information that the user needs to enable the installation
air conditioning contractor prior to actual testing, and equipment to be efficiently and economically
adjusting and balancing and shall ensure the operated and maintained. It should also provide a
following: record of the outcome of any site testing, balancing
and regulation carried out prior to handover.
a) Hydronic system is free of leaks, hydrostatically
tested and is thoroughly cleaned, flushed and Handover documentation should include the
refilled. folIowing:

b) Hydronic system is vented. a) Description of the installation, including

PART 8 BUILDING SERVICES — SECTION 3 AIR CONDITIONING, HEATING AND MECHANICAL VENTILATION 47
simplified line flow and balance diagrams for e) Schedules of mechanical equipment;
the complete installation; f) Test results and test certificates as called for
b) As-built installation drawings; under the contract including any insurance or
c) Operation and maintenance instructions statutory inspection authority certificate;
for equipment, manufacturer’s service g) Copies of guarantee certificates for plant and
maintenance manuals, manufacturer’s spare equipment; and
parts list and spares ordering instructions; h) List of keys, tools and spare parts that are
d) Schedules of electrical equipment; handed over.

LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’
(4) 3103:1975 Code of practice for industrial
in the fulfillment of the requirements of the Code. The
ventilation (/irst revision)
latest version of a standard shall be adopted at the time
of enforcement of the Code. The standards listed may (5) 3315:1994 Specification for evaporative
be used by the Authority as a guide in conformance air coolers (desert coolers)
with the requirements of the referred clauses in the Code. (second revision)
(6) 1391 Specification for room air
In the following list, the number appearing in the first
conditioners:
column within parentheses indicates the number of the
reference in this Part/Section. (Part 1): 1992 Unitary air conditioners
(second revision)
IS No. Title
(7) (Part 2): 1992 Split air conditioners (second
(1) 655:1963 Specification for metal air
revision)
ducts (revised)
(8) 8148:2003 Specification for packaged air
(2) 277:2003 Specification for galvanized
conditioners (jirst revision)
steel sheet (plain and
corrugated) (sixth revision) (9) 4831:1968 Recommendation on units and
(3) 737:1986 Specification for wrought symbols for refrigeration
aluminium alloy sheet and (lo) 5:1994 Specification for colours for
strip for general engineering ready mixed paints and
purpose (third revision) enamels ~ourth revision)

48 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES
Section 4 Acoustics, Sound Insulation and Noise Control

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE . .. 5
2 TERMINOLOGY ... 5
3 PLANNING AND DESIGN AGAINST OUTDOOR NOISE ... 8
4 PLANNING AND DESIGN AGAINST INDOOR NOISE ... 11
5 RESIDENTIAL BUILDINGS ... 11
6 EDUCATIONAL BUILDINGS ... 13
7 HOSPITAL BUILDINGS ... 16
8 OFFICE BUILDINGS ... 18
9 HOTELS AND HOSTELS ... 20
10 INDUSTRL4L BUILDINGS ... 21
11 LABORATORIES AND TEST HOUSES ... 25
12 MISCELLANEOUS BUILDINGS ... 26

ANNEX A NOISE CALCULATIONS ... 28


ANNEX B SPECIFICATION OF SOUND INSULATION . .. 31
ANNEX C NOISE RATING ... 32
ANNEX D OUTDOOR NOISE REGULATIONS IN INDIA ... 33
ANNEX E SPECIAL PROBLEMS REQUIRING EXPERT ADVICE ... 33
ANNEX F AIR-BORNE AND IMPACT SOUND INSULATION ... 34
ANNEX G BASIC DESIGN TECHNIQUES FOR NOISE CONTROL IN ... 41
AIR CONDITIONDJG, HEATING AND MECHANICAL
VENTILATION SYSTEM
ANNEX H SUGGESTED EQUIPMENT NOISE DATA SHEET ... 42

LIST OF STANDARDS ,.. 43

NATIONAL BUJLDING CODE OF INDIA


National Building Code Sectional Committee, CED 46

FOREWORD

This Section covers the acoustical, sound insulation and noise control requirements in buildings. Emphasis is
laid on planning of buildings vis-a-vis its surroundings to reduce noise and in addition sound insulation aspects
of different occupancies are covered for achieving acceptable noise levels.

This Section was f~st published in 1970 and was subsequently revised in 1983. In the last revision mainly the
following changes were made:

a) The approximate measured noise levels due to various types of traffic (air, rail and road) were given;
and planning and design features of buildings against outdoor noise were elaborated,
b) Impact sound insulation in residential buildings was modified to grade system of impact sound insulation;
c) Recommendations regarding planning of open plan schools against noise were given;
d) Planning of office buildings with light weight partitions was specified;
e) Planning and design aspects of hotels and hostels, laboratories and test houses, and other miscellaneous
buildings, such as, law courts and councils chambers, libraries, museums and art galleries, auditoria and
theatres had been given;
f) Hearing damage risk criteria in industrial buildings were modified based on permissible exposure limits
for a steady state noise level; and
g) The public address system was elaborated to cover public address system at passenger terminals.

In this revision, the following important changes have been made:

a) Large number of important definitions have been added in line with the present international practice of
usage of terms in the field of acoustics, sound insulation and noise control.
b) Under Planning and Design against Outdoor Noise, a new clause on Highway Noise Barrier has been
included.
c) The clause on public address system has been deleted.
d) A new clause on cinema has been added.
e) Existing Appendix A ‘Constructional Measures for Sound Insulation of Buildings’ and Appendix B
‘Sound Insulation Values for Various Types of Materials and Construction’ have been deleted and the
following new informative annexes have been added:
1) Annex A Noise Calculations
2) Annex B Specification of Sound Insulation
3) Annex C Noise Rating
4) Annex D Outdoor Noise Regulations in India
5) Annex E Special Problems Requiring Expert Advice
6) Annex F Airborne and Impact Sound Insulation
7) Annex G Basic Design Techniques for Noise Control in Air Conditioning, Heating and Mechanical
Ventilation System
8) Annex H Suggested Equipment Noise Data Sheet

There are two types of noises, that is, air-borne and structure-borne noise. To reduce the intensity of air-borne
noise, sound absorbent materials may be used.

An absorbent material is one which reduces the intensity of sound reflected from its surface. It may be applied to
walls, floors, ceilings or used as furnishings to reduce the sound level by absorption. However, the materials
selected for sound absorption shall be consistent with fire safety requirements of the buildings.

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS. SOUND INSULATION AND NOISE CONTROL 3
r

To reduce the transmission of air-borne noise, sound insulating materials maybe used. Sound insulating materials
block the passage of noise through them by virtue of their mass and physical properties. The extent of noise
reduction provided by a single homogeneous panel is proportional to the logarithm of mass per unit area. For
high values of sound insulation, normally heavy panels are required. Thin sheets of materials do not have adequate
mass for providing any appreciable sound transmission loss by themselves. However, when thin sheet materials
are used in a double panel construction with an intervening air cavity, this special construction can give extremely
high sound transmission loss values considering the mass of the partition, if designed properly. Porous materials
lack the mass required to provide any appreciable sound transmission loss, and readily allow sound at most
frequencies to be transmitted through them.

To reduce the transmission of structure-borne noise (such as, noise generated by impacts) special construction
methods and elastic discontinuity in the structure may be used. Structure-borne noise reduction is effected by
corner joints, changes in cross-section, changes in materials, etc, in construction. The reduction by these
construction methods is, however, not appreciable specially when a large amount of noise reduction is required
over a short distance. In such cases, introduction of an elastic discontinuity in the structure can result in a very
large amount of noise reduction. The noise transmission is affected only above a certain lower frequency which
depends on the material thickness and the elastic properties of the material. Bonded fibrous materials, rubber
elastomers, cork, etc, are suitable for curtailing structure-borne noise transmission.

This Section is largely based on the following standards:

IS 1950:1962 Code of practice for sound insulation of non-industrial buildings


IS 3483:1965 Code of practice for noise reduction in industrial buildings
IS 4954:1968 Recommendations for noise abatement in town planning
IS 11050 Rating of sound insulation in buildings and of building elements:
(Part 1) :1984 Airborne sound insulation in buildings and of interior building elements
(Part 2) :1984 Impact sound insulation ,
\
BS 8233:1999 Code of practice for sound insulation and noise reduction for buildings

In this revision, opportunity has been taken to update all references to relevant Indian Standards referred to in the
text.

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

4 NATIONAL BUILDING CODE OF INDIA


NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES
Section 4 Acoustics, Sound Insulation and Noise Control

1 SCOPE 2.8 Broad Band Noise — Spectrum consisting of a


large number of frequency components, none of which
This Section covers requirements and guidelines
is individually dominant.
regarding planning against noise, acceptable noise
levels and the requirements for sound insulation in 2.9 Cross-Talk — Unwanted sound transmission
buildings with different occupancies. between one, room and another room or space via a
duct.
2 TERMINOLOGY
2.10 Decibels — Ten times the logarithm (to the base
2.0 For the purpose of this Section, the following 10) of the ratio of two mean square values of sound
definitions shall apply. pressure, sound power or sound intensity. The
2.1 Ambient Noise — The sound pressure levels abbreviation for ‘decibels’ is dB.
associated with a given environment. Ambient noise
2.11 Effective
Perceived Noise Level in Decibel
is usually a composite of sounds from near and far
(EPN dB) — The number for rating the noise of art
sources none of which are particularly dominant.
individual aircraft flying overhead is the effective
2.2 Audible Frequency Range — The range of sound perceived noise level in decibels (EPN dB). The -
frequencies normally heard by the human ear. The effective perceived noise decibel value takes into
audible range spans from 20 Hz to 20000 Hz. account the subjectively annoying effects of the noise
including pure tones and duration. In principle, it is a
2.3 A-Weighted Sound Pressure, PA — Value of
kind of time-integrated loudness level.
overall sound pressure, measured in pascals (Pa), after
the electrical signal derived from a microphone has 2.12 Equivalent Continuous A-Weighted Sound
been pased through an A-weighting network. Pressure Level, L~eq ~ — Value of the A-weighted
NOTE — The A-weighting network modifies the electrical sound pressure level in decibels (dB) of a continuous,
response of a sound level meter with frequency in approximate y steady sound, that within a specified time interval, T,
the same way as the sensitivity of the human hearing system. has the same mean squared sound pressure as the sound
2.4 A-Weighted Sound Pressure Level, LPA — under consideration that varies with time, given by the
Quantity of A-weighted sound pressure, given by the formula:
following formula in decibels (dBA):

where
where
PA = is theA-weighted sound pressure in pascals
(Pa); and PA(O = is the instantaneous A-weighted sound
pressure in pascals (Pa); and
P,, = is the reference sound pressure (2o p pa).
P. = is the reference sound pressure (20p Pa).
NOTE — Measurements of A-weighted sound pressure level
can bc made with a meter and correlate roughly with NOTE — Equivalent continuous A-weighted sound pressure
subjective assessments of loudness, and are usually made to level is mainly used for the assessment of environmental noise
assist in judging the effects of noise on people. The and occupational noise ex@sure.
size of A-weighting in 1/3 octave bands, is shown in
Annex A (see A-5). An increase or decrease in level of 2.13 Equivalent Sound Absorption Area of a Room,
10 dBA corresponds roughly to a doubling or halving of
A — Hypothetical area of a totally absorbing surface
loudness.
without diffraction effects, expressed in square metres
2.5 Background Noise — The sound pressure levels (m2) which, if it were the only absorbing element in
in a given environment from all sources excluding a the room, would give the same reverberation time as
specific sound source being investigated or measured. the room under consideration.
2.6 Break-in — Unwanted sound transmission into a 2.14 Facade Level — Sound pressure level measured
duct from outside. 1 m to 2 m in front of the fagade.
2.7 Break-out — Unwanted sound transmission from NOTE— Facadelevelmeasurementsof LPAare usually 2 dB to
inside a duct to the outside. 3 dB higher than corresponding free-field measurements.

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 5
2.15 Free-Field Level — Sound pressure level NOTE — Normalized impact sound pressure level is usually
measured outside, far away from reflecting surfaces. used to characterize the insulation of a floor in a laboratory
against impact sound in a stated frequency band (see Annex B).
NOTE — Measurements made 1.2 m to 1.5 m above the ground
and at least 3,5 m away from other reflecting surfaces are usually 2.25 Octave hand — Band of frequencies in which
regarded m being free-field measurements. To minimize the the upper limit of the band is twice the frequency of
effect of reflections the measuring position should be at least the lower limit.
3.5 m to the side of the reflecting surface (that is, not 3.5 m
from [he reflecting surface in the direction of the source). 2.26 Percentile Level, Lm ~ — A-weighted sound
Estimates of noise from aircraft overhead usually include a pressure level obtained usi’ng time-weighting ‘F’,
correction of 2 dB to allow for reflections from the ground.
which is exceeded for N percent of a specified time
2.16 Frequency — The number of cyclical variations interval.
per unit time. Frequency is generally expressed in
Example:
cycles per second (cps) and is also denoted as Hertz
(Hz). L ~go.l~is the A-weighted level exceeded for 90
percent of 1 h. Percentile levels determined over
2.17 Impact Sound Pressure Level, Z,i — Average
a certain time interval cannot accurately be
sound pressure level in a specific frequency band in a
extrapolated to other time intervals. Time-
room below a floor, when it is excited by a standard
weighting ‘F’ or ‘S’ can be selected on most
tapping machine.
modern measuring instruments and used to
2.18 Indoor Ambient Noise — Pervasive noise in a determine the speed at which the instrument
given situation at a given time, usually composed of responds to changes in the amplitude of the signal.
noise from many sources, inside and outside the Time-weighting ‘F’ is faster than ‘S’ and so its ---
building, but excluding noise from activities of the use can lead to higher values when rapidly
occupants. changing signals are measured.

2.19 Insertion Loss (Lm) 2.27 Pink Noise — Sound with an uninterrupted
frequency spectrum and a power which is steady
Insertion loss is generally defined as the difference, in
within frequency band and proportional to centre
decibels, between two sound pressure levels (or power
frequency. An example is constant power level per
levels or intensity levels) which are measured at the
octave band.
same point in space before and after a muffler or any
other noise control device is inserted between the 2.28 Pure Tone — A sound emitted at a single
measurement point and the noise source. frequency.

2.20 Noise — Unwanted sound which may be 2.29 Rating Level, L~r,Tr — Equivalent continuous
hazardous to health, interferes with communications A-weighted sound pressure level of the noise, plus any
or is disturbing. adjustment for the characteristic features of the noise.

2.21 Noise Exposure Forecast (NEF) — The noise NOTE — This definition is used for rating industrial noise,
where the noise is the specific noise from the source under
exposure forecast at any location is the summation of
investigation.
the noise levels in EPN dB from all aircraft types, on
all runways, suitably weighted for the number of 2.30 Reverberation Time, T — Time that would be
operations during day time and night time. required for the sound pressure level to decrease by
60 dB after the sound source has stopped.
2.22 Noise Rating (NR) — Graphical method for
rating a noise by comparing the noise spectrum with a NOTE — Reverberation time is usually measured in octave or
third octave bands. It is not necessary to measure the decay over
family of noise rating curves. the full 60 dB range. The decay measured over the range 5 dB
NOTE — Noise rating is described in Annex C. to 35 dB below the initial level is denoted by TgO,and over the
range 5 dB to 25 dB below the initial level by T20.
2.23 Noise Reduction Co-efilcient (NRC)
2.31 Sound — A vibrational disturbance, exciting
A single figure descriptor of the sound absorption hearing mechanisms, transmitted in a predictable
property of a material. It is the arithmetic mean of the manner determined by the medium through which it
sound absorption co-efficients at 250, 500, 1000 propagates. To be audible the disturbance shall have
and 2000 Hz rounded off to the nearest multiple to fall within the frequency range of 20 Hz to
of 0.05. 20000 Hz.
2.24 Normalized Impact Sound Pressure Level, Ln 2.32 Sound Exposure Level, Lm — Level of a sound,
— Impact sound pressure level normalized for a of 1 s duration, that has the same sound energy as the
standard absorption area in the receiving room. actual noise event considered.

6 NATIONAL BUILDING CODE OF INDIA


NOTES 2.38 Sound Reduction Index, R — Laboratory
1 The L.mof a discrete noise event is given by the formula measure of the sound insulating properties of a material
or building element in a stated frequency band.
NOTE— For further informationsee Annex B.

2.39 Sound Source — Equipment or phenomena


where
which generate sound. Source room is the room
P.(t) = is the instantaneous A-weighted sound containing sound source.
pressure in pascals (Pa);
2.40 Spectrum — A quantity expressed as a function
tz–tl = is a stated time interval in seconds (s) long of frequency, such as sound pressure versus frequency
enough to encompass all significant sound curve.
energy of the event
2.41 Standardized Impact Sound Pressure Level,
P. = is the reference sound pressure level (20p
~~~— Impact sound pressure level normalized to a
Pa); and
reverberation time in the receiving room of 0.5 s.
to = is the reference time interval (1 s).
NOTE — Standardized impact sound pressure level is used to
2 LAE is also known as LAX (single-event noise exposure level). characterize the insulation of floors in buildings against impact
.
sound in a stated frequency band (see Annex B).
2.33 Sound Power — The acoustic power of a sound
source, expressed in Watts. 2.42 Speech Interference Level (SIL) — A descriptor
for rating steady noise according to its ability to
2.34 Sound Power Level, Lw — The acoustic power
I interfere with conversation between two people. SIL
radiated from a given sound source as related to a
is the arithmetic average of the sound pressure levels
reference power level (typically 10-]2 watts) and
in the three octave bands with centre frequencies
expressed in decibels as:
at 500, 1000 and 2000 Hz.
w

where
Lw =lOlog
{1
—
~o-12
2.43 Standardized Level Difference, Dn~ —
Difference in sound level between a pair of rooms, in
a stated frequency band, normalized to a reverberation
W = Acoustic power in watts. time of 0.5 s.
NOTE — Standardizedlevel difference tafcesaccount of all
By definition, 1 W therefore corresponds to 120 dB soundtransmissionpaths betweenthe rooms (see Annex B).
for Lw.
2.44 Structure Borne Noise — Generation and
2.35 Sound Pressure,p — Root-mean-square value propagation of time dependent motions and forces in
of the variation in air pressure measured in pascals (Pa), solid materials which result in unwanted radiated sound.
above and below atmospheric pressure, caused by the
sound. 2.45 Transient Sound — Sound which is audible for
a limited period of time, for example sound from over
2.36 Sound Pressure Level, Lp — Quantity of sound flight of an airplane.
pressure, in decibels (dB), given by the formula:
2.46 Third Octave Band — Band of frequencies in
LP= 10 log10 (p/pO)* which the upper limit of the band is 2 1’3times the
where frequency of the lower limit.
P = is the root mean square sound pressure in 2.47 Threshold of Hearing — The lowest continuous
pascals (Pa); and sound pressure level which will create an auditory
P<, = is the reference sound pressure (20p Pa). sensation for the average human ear. Any sound below
NOTE — The range of sound pressures for ordinary sounds these levels will be inaudible and any sound above the
is very wide. The use of decibels gives a smaller, more threshold will vary in loudness dependent on intensity.
convenient range of numbers. For example, sound pressure
levels ranging from 40 dB to 94 dB correspond to sound 2.48 Vibration Isolation — Reduction of force or
pressures ranging from 0.002 Pa to 1 Pa. A doubling of sound displacement transmitted by a vibratory source, often
energy corresponds to an increase in level of 3 dB. attained by use of a resilient mount.
2.37 Sound Receiver — One or more observation 2.49 Wavelength — The length in space of one
points at which sound is evaluated or measured. The complete cycle of a sound wave.
effect of sound on an individual receiver is usually
evaluated by measurements near the ear or close to ~= (Speed of sound) _@
the body. (fi-equency) - (f)

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL
2.50 Weighted Level Difference, DW — Single- survey should examine all the possible causes of noise
number quantity that characterizes airborne sound and consider the various factors causing actual nuisance.
insulation between rooms but which is not adjusted to
3.1.2 Noise by night, causing disturbance of sleep, is
reference conditions.
more of nuisance than noise by day. For this reason,
NOTE — Weighted level difference is used to characterize the housing colonies that adjoin areas with heavy traffic
insulation between rooms in a building as they are; values cannot
movement during the night are liable to cause serious
normally be compared with measurements made under other
conditions {see good practice [8-4(1)]]. complaints. Also, the factories that work by night are
liable to cause serious complaints if housing estates
2.51 Weighted Sound Reduction Index, Rw _ Single adjoin them. While planning, care should be taken that
number quantity which characterizes the airborne housing colonies are adequately setback from busy
sound insulating properties of a material or building airports, state and national highways, factories, main
element over a range of frequencies. railway lines and marshaling yards.
NOTE — The weighted sound reduction index is used to
characterize the insulation of a material or product that has been
3.1.3 There are two aspects of defence by planning. The
measured in a laboratory (see Annex B). first is to plan so as to keep the noise at a distance. Under
this aspect comes the separation of housing from traffic
2.52 Weighted Standardized Impact Sound Pressure
noise by interposing buffer zones, and the protection of
Level, L’n~ ~ _ Single number quantity used to
schools and hospitals by green belts, public gardens,
characterize the impact sound insulation of floors over
etc. The second is the principle of shading or screening.
a range of frequencies.
This consists of deliberately interposing a less vulnerable
NOTE — Weighted standardized impact sound pressure level building to screen a more vulnerable one or by providing ,.-
is used to characterize the insulation of floors in buildings (see a solid barrier, such as a wall, between the source and
Annex B).
the location to be protected.
2.53 Weighted Standardized Level Difference,
D .,~w __Single-number quantity, which characterizes 3.2 Traffic Noise Levels
the airborne sound insulation between rooms 3.2.1 For Air Traffic
NOTE — Weighted standardized level difference is used to For guidance, approximate noise levels due to various
characterize the insulation between rooms in a building (see
Annex B). types of aircrafts, measured on ground, when the
aircrafts fly overhead at a height of 450 m, are given
2.54 Weighted Normalized Impact Sound Pressure in Table 1.
Level, L’n ~ — Single number quantity used to
characterize the impact sound insulation of floors over Table 1 Typical Noise Levels of Some
a range of frequencies. Aircarft Types
NOTE — Weighted normalized impact sound pressure level is (Clause 3.2.1)
usually used to characterize the insulation of floors tested in a
laboratory (see Annex B). SI Type of A]rcraft Flyover Noise Levels at 450 m
No. with Take-off Thrust (EPN dB)
2.55 White Noise — A noise whose spectrum (level) (1) (2) (3)
density is substantially independent of frequency over Boeing 737 107
O
a specified range and has equal power for any range ii) Boeing 747-200 103
of frequencies of constant band width. iii) Airbus A 300 101
iv) Concorde SST 114
3 PLANNING AND DESIGN AGAINST
OUTDOOR NOISE 3.2.2 For Rail Traffic

3.1 General Noise levels of some typi’cal railway traffic are given
in Table 2.
Planning against noise should be an integral part of
town and country planning proposals, ranging from Table 2 Typical Noise LeveIs of Railway Trains
regional proposals to detailed zoning, and three- (Clause 3.2.2)
dimensional layouts and road design within built-up
areas. Noise nuisance should be fully recognized in S1 Type of Train NoiseLevel at 30 ~ Measured
No. on the Side or in the Direction
zoning regulations. of Trs@ dkt(k)

3.1.1 Noise is either generated by traffic (road, rail and (1) (2) (3)

underground railway) or it arises from zones and i) Steam train, 60 km/h 85


buildings within built-up areas (industry, commerce, ii) Diesel train, 60 km/h 83
iii) Electric train, 60 frm/h 77
offices and public buildings). For planning, the noise

8 NATIONAL BUILDING CODE OF INDIA


3.2.3 For Road Traflc potentially harmful to health. It is important that no
new development is carried out within areas where the
The level of noise generated by road traffic depends
expected noise levels will cause mental and physical
upon such factors as the number of vehicles passing
fatigue or permanent loss of hearing. In case
per hour, the type of traffic, the preponderance of heavy
development in such areas is essential, adequate sound
vehicles, average speed, gradient and smoothness of
insulation shall be provided for the building.
traffic flow. The smoothness of traffic flow also affects
variability of the noise and is governed by such things 3.4.1.2 As the problems caused by aircraft noise have
as roundabouts and traffic lights, and the volume of become more acute, a number of methods have been
traffic and pedestrian movement with their effects on devised for evaluating noise exposure in the vicinity
stopping, starting and overtaking. The level of traffic of airports. They all combine many factors into a single
noise fluctuates continuously and the way it does has number evaluation. A commonly used criterion is the
a considerable effect on the nuisance caused. For noise exposure forecast (NEF). The NEF is used
assessing traffic noise, noise is measured in dB(A). primarily to develop noise contours for areas around
Because of the fluctuating nature of traffic, noise levels airports. It has been accepted generally that noise
due to different volumes of traffic flow with a varying exposure forecast levels greater than NEF 40 are
mix of vehicles are given in Table 3. unacceptable to people while levels less than NEF 25
are normally acceptable.
Table 3 Typical Noise Levels Due to
3.4.1.3 While it is theoretically possible to provide
Free-Flowing Road Traffic
sufficient insulation to achieve an acceptable indoor
(Clause 3.2.3) noise environment in the area of very high outdoor
noise, there is a level above which aircraft noise
sl Type of Tr~lc L.1030 m from Edge
No. of Road, dB(A) seriously affects living conditions no matter how much
(1) (2) (3) sound insulation has been applied to the dwelling unit.
For this reason it is recommended that no residential
i) 5020 vehicles per 18 hoar day 65
(10 percentheavyvehicles),50kmph development be allowed beyond the NEF 35 level.
ii) 10000 vehicles per 18 hour day 70 3.4.1.4 During summer months, the windows are
(20 pereentheavyvehicles),60 kmph
norrnall y kept open for adequate ventilation. In view
iii) 10000 vehicles per 18 hour day 75
(40 percentheavyvehicles),80 kmph of this, no matter how much sound insulation is
iv) 20000 vehicles per 18 hour day 77 provided for the building structure, the noise level
(40 percentheavy vehicles),80 kmph inside the room can never be less than 10 dB below
the outdoor noise level. For very critical buildings,
NOTE — The values are applicable to free flowing traffic
without honking. such as buildings necessary for maintaining and
supplementing the airport services, and for commercial
3.3 Outdoor Noise Regulations development, such as hotels, it is possible to provide
sealed windows and to centrally air-condition the entire
The outdoor noise regulations in force from time-to-
building. However, it is not feasible for most of the
time shall be complied with (see also Annex D).
residential developments in the country. In such cases
3.4 Planning and Design proper zoning regulations and siting of vulnerable
buildings away from aircraft noise are of vital
3.4.1 For Air Traffic
importance.
Near airports two sources of aircraft noise should be
3.4.2 Rail Tra&
considered.
This is a very serious source of noise in built-up areas,
a) Flyover noise — Flyover noise is that which
both by day and by night,llailway cuttings reduce the
occurs under flight paths close to airports and
spread of noise, whereas embankments extend it. The
is the most serious and common problem. As
elevated railway on viaducts or embankment is very
the aircraft passes overhead the noise level at
common in built-up areas. The elevation increases
any particular location rises to a peak and then
exposure to noise but in addition the construction of
decreases.
the viaduct may effect the propagation of noise. In this
b) Ground noise — The noise emitted by an
respect solid embankments are preferable to built-up
aircraft during ground operations is less
arches, which tend to act as sound boxes. Worst of all
variable in direction than flyover noise, but
are the steel bridges, which greatly magnify the noise
is usually of a longer duration.
due to vibration. Uphill gradients are another feature
3.4.1.1 Aircraft noise may disturb sleep, rest and tending to increase noise, especially of heavy goods
communication, and as s-uch may be considered trains.

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 9
3.4.2.1 Wherever possible, no residential or public lights, near bus stops, on steep slopes and in parking
building zone should abut onto railway lines, especially spaces and enclosed yards.
on the marshaling yards which is particularly
3.4.3.3 For zoning and planning new buildings in
objectionable because of the shrill, clanging and
urban areas it is recommended that external LAIOis
intermittent noise they generate, often at night. The
limited to a maximum of 70 dB(A) when the dwellings
appropriate zones along side railway lines are industrial
are proposed to have sealed windows and 60 dB(A)
and commercial buildings other than office buildings.
when the dwellings are proposed to have open
Where these precautions are not practicable and
windows. Indeed it is desirable to confine major new
housing has to abut on to railway lines, every attempt
residential development to locations subject to L~10
may be made to house as few people as possible in the
levels substantially lower than those given above.
vicinity of the railway lines.
It is recognized, however, that within the large urban
3.4.2.2 Underground transportation system can be a
areas, the use of sites where the external LAIOis greater
major cause of disturbance for the neighboring
than 60-70 dB(A) can not always be avoided. In that
community. Very high noise levels are propagated to
case it is suggested to utilize such design solutions as
long distances by the underground high speed railway,
barrier blocks in order to reduce external L~10 noise
as a result of wheel rail interaction. Both air-borne noise
levels to at least 60-70 dB(A) at any point 1.0 m from
and ground or structure-borne vibration are potential
any inward looking faqade. When the orientation of
sources of complaints. Noise control measures,
site and the density of development are such that this
therefore, need to be considered for the following:
cannot be fully achieved some form of dwelling
a) In stations, where high noise levels are insulation will have to be provided. It should be
produced at the arrival and departure of appreciated that where open windows are a must, the
trains; occupants would have to put up with discomfort if the
b) In tunnels, during high speed train movement; above conditions are not met.
c) Where an underground rail transit system 3.4.3.4 Certain other methods can often be utilized to
passes close to existing structures or high rise provide economical and effective protection from noise:
buildings adequate attention should also be
paid to the problem of ground vibration a) Methods may be adopted to improve the
transmitted to the building, and proper smoothness of flow and reduce number of
isolation should be provided for critical areas; stopping and starting. This leads to an
improvement even if it leads to increased
d) Wherever elevated railway tracks are provided,
flows. Flow linking of traffic lights, for
adequate measures should be taken to avoid
example, may reduce noise nuisance.
the spread of noise in the surrounding built
up areas; and b) Use of roads passing through residential areas
may be prohibited to heavy commercial
e) In transit cars, where sound insulation is of
vehicles. An alternative would be to limit use
vital importance to provide comfortable
by commercial vehicles to certain times of
conditions for the commuters.
the day.
3.4.3 Road Tra@c c) Use of honking may be prohibited near
3.4.3.1 Convoys of long distance heavy trucks at night sensitive buildings, such as hospitals and the
moving past through built-up areas cause serious noise like.
complaints. On busy roads, the noise of continuous d) Barriers may be provided to shield sites from
traffic may be a worse nuisance than that of railways. noise.
At least the same precautions may, therefore, be taken
3.5 Zoning
in the planning of dwellings in relation to arterial and
trunk roads as with railways. Care may be taken that The zoning of the different cities shall be done by the
local housing roads do not provide shortcuts for heavy town planning authorities, taking into account besides
traffic through residential areas. Hilly roads present other aspects, the noise levels from different
the additional noise of gear changing. Trees with heavy occupancies. Wherever necessary, experts in the field
foliage planted on both sides of carriageway help may be consulted. For detailed information on noise
slightly to muffle the noise, provided the foliage reduction for town planning schemes, reference may
extends for a considerable distance (30 m or above,). be made to good practice [8-4(2)].
3.4.3.2 Road traffic may give rise to serious nuisance
3.6 Green Belts and Landscaping
particularly on busy thorough fares, between
continuous high buildings in main streets, at the traffic Where relief from noise is to be provided by means of

10 NATIONAL BUILDING CODE OF INDIA


green belts these may be of considerable width and be Table 4 Acceptable Indoor Noise Levels for
landscaped. (In case of railway tracks, a minimum Various Buildings
distance of 50 m to 70 m may be provided between (Clause 4.1)
the buildings and the tracks.) The extent of relief that
may be derived from the above maybe estimated only sl Location Noise L&vel
after considering other environmental factors. Only No. dB(A)

thick belts of planting (greater than 30 m) are of real (1) (2) (3)

value. Strong leafy trees may be planted to act as noise i) Auditoria andconcert halls 20-25
baffles. Shrubs or creepers may also be planted for ii) kdiO and ~ StUdiOS 20-25
iii) Cinemas 25-30
additional protection between tree trunks; artificial iv) Music rooms 25-30
mounds and banks should be formed where practicable. v) Hoapi,,s audcinema theatres 35-40
As little hard paving and as much grass as possible vi) Apartments,hotels and hotncs 35-40
vii) conference rooms, small offices and 35-40
may be used. The creation of green belt is particularly
likxaries
advisable on the perimeter of aerodromes, along viii) Courtmoms and classrooms 40-45
railway lines and arterial roads, through or past built- ix) Large public offices, banksand stores 45-50
up areas and adjoining noisy industrial zones. x) Restauranta 50-55

3.7 Highway Noise Barriers 4.2 Vulnerable Buildings


Barriers are often the most effective means of reducing Some buildings or parts of buildings are specially
traffic noise around residential areas. They have the vulnerable to noise, for example, recording and radio
great advantage that they generally protect most or all studios, hospitals and research laboratories. These
of the site. In nearly all situations, a well-designed should not be sited near loud noise sources. Most
barrier of even a modest height (say 3 m) can at least vulnerable buildings contain some areas which are
ensure that all areas of open space are free from themselves noisy and in such buildings the less
excessive noise levels. vulnerable elements should be planned to act as noise
buffers. Most noisy buildings also contain quiet
There are two types of barriers that can be built to
accommodation, which equally may be planned to act
protect sites; one which are built solely for the purpose
as a buffer between the noisy part of the building and
of reducing noise and two, which form part of the
adjoining vulnerable buildings.
building complex (barrier blocks). Free standing walls
and artificial mounds are typical examples of the first 4.3 The details of site and internal planning and
type while single and multi-storeyed dwellings and/or insulation requirements are covered under individual
garages are the most common form of the second. occupancies (5 to 12) as applicable to the respective
character and sources of noise in different buildings.
Of the two types, barrier blocks are more widely used
because they are cheaper and also tend to forma more 4.4 Sound Insulation of Non-Industrial Buildings
effective barrier overall because of their greater height by Constructional Measures
and width. B tier walls or mounds are more limited
in their effect than barrier blocks for they protect little The desired (acceptable) noise levels and the
more than the area of the site close to ground level recommended insulation values for the various areas
essentially because of the lack of height, as continuous may be achieved by providing sound insulation
walls much higher than 3 m are often difficult to treatments by constructional measures. The details of
construct. the same are given in Annex F. The recommendations
given in Annex F are applicable to non-industrial
3.8 Special Problems Requiring Expert Advice buildings like residences, educational buildings,
The purpose of noise control is to ensure that people hospitals and office buildings.
are neither harmed not disturbed by noise. In addition 4.5 Special Problems Requiring Expert Advice —
to provisions given in this Section, special advice may (see 3.8 and Annex E).
be required for more complex situations, such as those
listed in Annex E. 5 RESIDENTIAL BUILDINGS

4 PLANNING AND DESIGN AGAINST INDOOR 5.1 Sources of Noise Nuisance


NOISE 5.1.1 Outdoor Noise
4.1 Acceptable Indoor Noise Levels in Buildings The main sources of outdoor noise in residential areas
The generally acceptable noise levels inside buildings are traffic (aeroplane, railways, roadways), children
are given in Table 4. playing, hawkers, services deliveries, road repairs

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 11
blaring loud-speakers and various types of moving 5.2.2 Internal Planning
machinery in the neighborhood ‘and buildin~
The orientation of buildings in a locality should be
operations.
planned in such a way as to reduce the noise
5.1.2 Indoor Noise disturbance from neighborhood areas. The non-
critical areas, such as corridors, kitchens, bathrooms,
5.1.2.1 As far as indoor noises are concerned,
elevators and service spaces may be located on the
conversation of the occupants, footsteps, banging of
noisy side and the critical areas, such as bedrooms and
doors, shifting of the furniture, operation of the cistern
living space, on the quiet side.
and water closet, playing of radio, television, music
system, cooling and ventilation machinery, etc, 5.2.2.1 Windows and doors
contribute most of the noise emanating from an
Windows and doors should be kept away from the
adjacent room or an adjacent building. Noise
noisy side of the building as given below, wherever
conditions vary from time-to-time and noise which may
possible:
not be objectionable during the day may assume
annoying proportions in the silence of the night when a) When windows of a building, particularly
quiet conditions are essential. those of bedrooms in apartments or flats, face
roads carrying heavy traffic or other noises
5.1.2.2 In the case of flats the main sources of noise
where the external noise is of the order of 80
are frotn other flats and from stairs, lifts and access
to 90 dB(A), the building should be located
balconies. Plumbing noise is another cause. In semi-
at a distance of about 30 m from the road, but
detached buildings, outdoor noises from streets are
a distance of 45 m or more, where possible,
noticed more than indoor noises from neighbors.
should be aimed at for greater relief from
5.2 Recommendations noise;
b) When the windows are at right angles to the
5.2.1 Site Planning
direction of the above type of noise, the
The most desirable method is to locate the residential distance from the road should be arranged to
buildings in a quiet area away from the noisy sources be about 15 to 25 m; and
like the industrial areas, rail tracks, aerodromes, roads c) In case another building, boundary wall or
carrying heavy traffic, etc. trees and plantations intervene between the
road traffic and the house/flat further noise
5.2.1.1 To minimize ground reflection, the dwellings
reduction is achieved and in such cases the
should be surrounded by the maximum amount of
above distances may be reduced suitably.
planting and grassed areas and the minimum amount
of hard surfacing. This applies particularly to high 5.2.2.2 Layout plans
density areas. Where for maintenance reasons a large
It is desirable that rooms adjoining party walls and
amount of hard paving is necessary, it should be broken
above/below party floors should be of similar use. By
up by areas of planting and grassing. Narrow hard
this means, bedrooms are not exposed to noise from
paved courts should be avoided between adjacent tall
adjoining living rooms, and there is less risk of
buildings.
disturbance of sleep.
5.2.1.2 Roads within a residential area should be kept
In semi-detached houses, the staircase, hall and kitchen
to a minimum both in width and length, and should be
should adjoin each other on each side of the party wall,
designed to discourage speeding. Area-wise planning,
thus providing a sound baffle between rooms requiring
with zones from which vehicular traffic is altogether
quiet conditions.
excluded will greatly help to reduce noise. Roads with
through traffic should be excluded from residential Bedrooms should not be planned alongside access
areas, but where sites have to be developed adjacent balconies, and preferably not underneath them. Where
to existing major roads the same principles should be the approach is by an internal corridor, a sound baffle
observed in the siting of blocks as with railway lines may usefully be provided by arranging internal
as covered under 3.4.2.L passages and bathrooms between the corridor and the
living room or bedrooms.
5.2.1.3 Play areas for older children should be sited
as far away from dwellings as possible. Special care Water-closets should not be planned over living rooms
should be taken with old peoples’ dwellings. They and bedrooms, whether within the same dwelling or over
should not be placed immediately adjacent to service other dwellings. Soil pipes should not be carried in ducts
entries, play spaces, or to any entrances where children which adjoin living rooms or bedrooms unless the side
may tend to congregate. of the duct next to these rooms is a solid wrdl containing

12 NATIONAL BUILDING CODE OF INDIA


m1 h]spection openings. Refuse chutes should not be of noise. For this purpose, some sound attenuating
planned next to living rooms or bedrooms. devices may be installed in these openings.
5.2.3 .yOLl~ld hYLddiOlll All partitions should be sealed effectively where they 4’
5.2.3.1 Reduction of air-borne noise butt against rest of the structure. All doors and windows
[
should be properly gasketed where a high degree of .!.]~
‘-[’heweighted sound reduction index, R , of’partitions sound insulation is desired. j
between individual rooms or apartment: of a building j
i
wit shall be as given in Table 5. These values may, 5.2.3.4 Reduction of structure-borne noise
ii
however, be suitably increased, where rec~uired, for This requires the use of discontinuous or non-
critical areas. homogeneous materials in the construction of the f’
structure. /
Table 5 Sound Insulation Between Individual !
I
Rooms (Air-Borne) 5.2.3.5 Reduction of impact noise
(Clause 5.2.3.1) The floor of a room immediately above the bedroom {
> !
S1 No. Situation R.,dB or living room shall provide impact sound pressure
(1) (2) (3) level (l.’., J not greater than 60 dB. For example,
150 mm thick concrete floor with thick carpet (12 mm) bb
i) Between the living room in one house or flat 50
and the living room and bedrooms in another covering would satisfy this requirement.
ii) Elsewhere between houses or flats 45
iii) Between one room and another in the same 35 5.2.3.6 Main staircases in blocks of flats are often
house or flat highly reverberant. Some of the surfaces at least (for
example, the soffits of stairs and landings) should be
NOTES
1 Where communicating doors are provided, all doors should
finished with sound absorbent materials wherever
be so designed as to provide recommended insulation required.
between the rooms.
2 There are cases when a set of houses or flats have to be 6 EDUCATIONAL BUILDINGS
built for the people who work at night and sleep during the
day. It is desirable to consider the design of at least one such 6.1 Sources of Noise Nuisance
room in each of the houses or flats which will provide an
insulation of about 45 dB in that room. 6.1.1 Outdoor Noise
3 The insulation values referred to are applicable with doors The outdoor sources of noise produced on school
and windows shut.
premises, which cause disturbance within the school,
5.2.3.2 Suppression of noise at the source itself include the noise arising from playgrounds, playing
fields and open-air swimming pools. Though
AH items of equipment that are potentially noisy should playgrounds are used mainly during break periods, they
be selected with care. Water-closet cisterns should not are also used for games and physical education at times
be fixed on partitions next to bedrooms or living rooms. when teaching is in progress in the adjoining class
Plumbing pipes should be isolated from the structures. rooms.
Lift motors should be mounted on resilient supports.
Access doors from machine rooms to internal staircases 6.1.2 Indoor Noise
should be well fitting and of solid construction. Special Indoor sources of noise are as follows:
noise control measures may be required for electrical
a) Singing, instrumental and reproduced music
and mechanical services such as diesel generators,
which may take place in class rooms and in
outdoor air conditioning units, cooling towers, etc.
dining and assembly halls particularly in
5.2.3.3 Reduction of air-borne noise transmitted primary schools. In secondary schools,
through the structure specialized music rooms are generally
Reduction of air-borne noise requires the use of rigid provided;
and massive walls without any openings. Openings are b) The movement of chairs, desks and tables at
the major cause of penetration of noise through a the end of one period may disturb a class .
barrier. While designing it should be borne in mind engaged in a lesson in a room below;
that all components should provide a sound transmission c) The shutting and openings of doors and
compatible with that of the rest of the barrier so that windows which may occur at any time during
an equivalent amount of sound energy is transmitted teaching periods;
through each portion of the barrier. d) Audio-visual presentations in class rooms;
Ventilating ducts or air transfer openings where e) Wood and metal workshops, machine shops
provided should be designed to minimize transmission (engineering laboratories); typing rooms e~c,

PART S BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 13
which produce continuous or intermittent e) Open planning and circulation areas —
sound of considerable loudness; Where open planning is used to permit
f) Practical work carried out in general teaching spaces, such as assembly halls, dining rooms
areas; or entrance halls to be used in association
with each other or for circulation, the degree
!9 Gymnasia and swimming pools;
of disturbance caused by interfering noise
h) School kitchens and dining spaces where food
to teaching areas needs careful consideration;
preparation and the handling of crockery and
traffic through such areas should be strictly
utensils persist for the greater part of the
controlled; full use should be made of
school day;
sound absorbent treatments to reduce the
j) Corridors and other circulation spaces; and spread of noise from one space to another
k) Plumbing and mechanical services. (see 6.2.3).
6.2 Recommendations If rooms have large glazed panels or ventilation
openings facing directly on the circulation
6.2.1 Site Planning areas, human traffic passing by the rooms
Where outdoor noise nuisance exists from local should be controlled. Preferably baffled
industry, busy roads, railway, a.irfklds, sport grounds ventilation system or double windows should
or other sources beyond the control of the school be used. (Fan-lights over doors should be
authority, school buildings should be sited as far as freed and glazed).
possible from the sources of noise. f) Furniture — In all educational buildings,
regardless of the character of the floor finish, “b
6.2.1.1 Rooms should be planned in a manner so that
rubber buffers should be fitted to the legs of
the minimum amount of glazing is placed on the side
chairs and tables.
facing the external noise.

6.2.1.2 Noises arising from the activities of a school 6.2.3 Noise Reduction within Rooms :
?-
and from the use of the buildings after school hours Sound absorbent materials play a useful part in
may constitute a nuisance to occupants of surrounding reducing the built-up or air-borne noise at source. In
property; therefore, it is desirable to place playgrounds, rooms, such as, classrooms, assembly halh and music
workshops, swimming pools, music rooms, assembly rooms, a fairly short reverberation time underoccupied
halls and gymnasia as far away as possible from conditions is one of the requirements of the acoustic
buildings which require a quiet environment. design. The maximum reverberation times permissible
6.2.2 Internal Planning for this purpose are usually short enough to give
adequate noise control but in addition, the reverberation
The following principles should be observed in the time should not be excessive under empty conditions,
detailed planning of educational buildings: because noise may occur in these rooms with very few
a) Grouping — Noisy rooms should be separated occupants. Table 6 gives the reverberation times often
from quiet ones, if possible. In general, it is arranged in occupied rooms for acoustic reasons and
desirable that rooms should be grouped the maximum times recommended in the empty rooms
together in accordance with the classification for noise reduction; the times given are for a frequency
given in 6.2.4.1. of 500 Hz, but they should not be greatly exceeded at
b) Windows and ventilators — Windows of noisy any frequency. When moms axe used for a variety of
and quiet rooms should not open on to the purposes, the reverberation period appropriate to the
same courtyard or be near to one another. major use should be adopted.
Roof lights and ventilators over noisy rooms 6.2.3.1 Special attenti6% should be given to noise
should be avoided, if they are likely to be a reduction in schools for the deaf and schools for the
source of nuisance to adjacent upper floors. blind. Deaf children are taught by means of hearing
c) Doors — Swing doors into rooms should aids which cannot be used satisfactorily in high noise
only be used where no problem of sound levels or in reverberant conditions. Blind children
transmission exists. Reduction of insulation depend on good hearing for understanding speech and
between rooms and corridors due to doors for detecting changes in environment. In both these
must be borne in mind. The type and method types of schools, noise levels should be kept low and
of fitting of doors is important and necessary reverberation times short. As an example, the
care shall be paid in this respect. reverberation times in empty class-rooms should
d) Sliding partitions should only be used where not exceed one second in schools for the blind or
essential. 0.5 second in schools for the deaf.

14 NATIONAL BUILDING CODE OF INDIA


Table 6 Reverberation Times in Schools a) In schools or institutes with a technical bias
(Clause 6.2.3) where noisy activities, such as sheet metal
work, plumbing and woodwork, are likely to
S1 Room Reverberation Tree,s be practised extensively in normal hours,
A
No. . -1
Usuat for Maximuml) for workshops should be regarded as a special
Acoustic Noise Control category requiring more than 45 dB isolation
Reasons (Futi) (Empty) (DW) from rooms of any other class.
(1) (2) (3) (4)
b) Assembly halls and music rooms are special
O Assembly hatls 1.0-1.25 1.5-2.5 cases in that, as well as producing noise, they
according according to
also require protection from it and may need
to size volume of hatt
ii) Music teaching rooms 0.75-1.25 1.5 more than 45 dB isolation (DW) from rooms
iii) Gymnasia nnd indoor — 1.5 in Class A, if the latter are very noisy.
swimming pools
iv) Dining rooms — 1.25 c) Circulation spaces may vary from along and
v) Classrooms 0.75 1.25 frequented corridor to a small private lobby
vi) Headmasters room and 0.5-1.00 1.0 and it is therefore difficult to give precise
staff rooms
recommendations to cover them. For partitions
between rooms in Class C and most corridors,
1)Shorter reverberation times are desirable for noise control
whenever Dossible. a RW of 35 dB for the partition itself is
adequate. For partitions between rooms in
6.2.4 Sound Insulation other classes and corridors, more or less
insulation may be necessary, depending upon ..-
6.2.4.1 Air-borne noise
the specific usage.
For purposes of sound insulation, rooms in educational
d) The problem of noise in circulation areas is
buildings may be classified as follows:
as a rule greatly mitigated in schools by the
fact that classes usually change rooms
Class A Noise Producing Workshops
together at regular times. In colleges and
Kitchens
evening institutes, however, this is much less
Dining rooms
Gymnasiums true and in such buildings particular attention
Indoor swimming should be paid to insulation between rooms
pools and corridors.
Class B Producing but Assembly halls 6.2.4.5 Open plan schools
needing quiet at Lecture halls
times Music rooms A new concept in school planning is the use of a large
Typing rooms teaching area with simultaneous instructions imparted
Class C Average General classrooms to several groups of students. These open plan teaching
Practical rooms areas offer a different set of problems. Because of the
Laboratories limitations in achieving a great deal of attenuation
Offices across the space and related dii%culties in noise control
Class D Rooms needing Libraries and speech interference, lecturing to a large number
quiet Studies of students is not possible without interfering with
Class E Rooms needing Medical rooms neighboring groups. The shape of such spaces may
privacy Staff rooms be as linear as possible with a width to height ratio of
5:1 or greater.
6.2.4.2 The recommended minimum sound reduction
In addition, special measures are required to be
(DW)between rooms of the same class is as follows:
introduced to reduce the level of intruding speech to
Class A — 25 dB an acceptable value so that the various teaching groups
Class C or D – 35 dB are not disturbed and adequate privacy is maintained.
Class B or E – 45 dB Judicious positioning of partial height barriers 1.8 m
to 2.1 m in height can improve the sound attenuation
6.2.4.3 Where a room is likely to have a dual use, for
between teaching groups and the use of reflective
example, a dining room to be used as a classroom, the
screens can reinforce the speech locally without
higher sound insulation value should be used. reflecting it to unwanted areas.
6.2.4.4 The recommended minimum sound reduction
6.2.4.6 Impact noise
(DW) between rooms in different classes is 45 dB
subject to the following: In the case of schools, the concrete floor of the room

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 15
immediately above the teaching rooms shall provide 2) Sterilizing eqnipment;
an impact sound pressure level, L’., ~Wnot greater than 3) Sluice room equipment including bedpan
70 dB. For example, a covering of 6 mm linoleum or washers;
cork tiles on concrete floor (hollow or solid) weighing 4) Ward kitchen equipment
not less than 220 kg/m2 will usually meet the above
5) Footsteps;
requirement.
6) Doors banging;
7 HOSPITAL BUILDINGS 7) The handling of metal or glass equipmen~

7.1 Creneral 8) Noises caused during maintenance and


overhaul of engineering services; and
Problems of noise control vary from hospital to hospital 9) Vacuum cleaners, mechanicrd polishers,
but the principles outlined below apply to all types. A etc.
quiet environment in hospitals is desirable for patients
b) Loudspeaker, radio or television, audible call
who are acutely ill. Staff require quiet conditions for
system, telephone bells and buzzers, and other
consultations and examinations and also in their living
air-borne noises, such as loud conversation;
and sleeping quarters. There have been rapid rises in
and
noise levels in hospitals due to the higher levels of
outdoor noise, increasing use of mechanical and mobile c) Noises from fixed or mobile equipment and
equipment (some of which is now brought much nearer services not directly concerned with hospital
to the patient in order to facilitate nursing procedure) routines. These include all the fixed services
and the introduction of loudspeaker, radio, television as given below:
..-
and call systems. Noise control in the hospital is made 1) Plumbing and sanitary fittings;
much more difficult by the extensive use of hard 2) Steam hot and cold water and central
washable surfaces which reflect and intensify the noise. heating pipes;
In most hospitals, windows to the open air and fanlights 3) Ventilation shafts and ducts;
to corridors are usually open for the purpose of Fans
4)
ventilation, admitting noise from outside and allowing
5) Boilers;
it to spread through the building.
6) Pumps;
7.2 Sources of Noise Nuisance 7) Air compressors;
7.2.1 Outdoor Noise 8) Pneumatic tubes;
9) Electrical and mechanical motors and
This may be classified into two main categories:
equipment;
a) Noise from sources outside the hospital 10) Lifts;
premises, for example, traffic and industrial 11) Laundry equipment; and
noises; and
12) Main kitchen equipment (refrigerators,
b) Noise from sources outside the building but mixers, steam boilers, etc).
usually within the control of the hospital
authority, for example, ambulances, motor-cars 7.3 Recommendations
and service vehicles, fuel and stores deliveries, 7.3.1 Site Planning
laundries, refuse collection, trucks and trolleys.
Hospital sites with their high degree of sensitivity to
7.2.2 Indoor Noise outside noise should be as far away from outside
A hospital is a complex building with many services sources as maybe compatible with other considerations,
and the numerous internal sources of structure-borne such as accessibility and availability of services. The
and air-borne noises are grouped into three main building should be so arranged on the site that sensitive
categories: areas like wards, consulting and treatment rooms,
operating theatres and staff bedrooms are placed away
a) Noise consequent upon hospital routines. This from outdoor sources of noise, if possible, with their
category includes sources which transmit windows overlooking areas of acoustic shadow.
noise through both structure-borne and air-
borne paths, many of which maybe quite near 7.3.2 Detailed Planning
to patients particularly those in wards, such There is a very large number of unit and room
as the following: classification in hospital design and in planning the
1) Wheeled trolleys of various kinds, for units in relation to each other and to the common
food and medical supplies; services (such as X-ray departments, operating theatre

16 NATIONAL BUILDING CODE OF INDIA


suits and main kitchens), noise reduction in the pressure and velocities. Silencing pipes and specially
sensitive areas should be weighed carefully against designed flushing action reduce water closet noise at
other design factors. Special care in overrdl planning source and make structural measures easier to apply.
and internal planning against noise is required in the The ventilation system should be designed so as not to
planning within the building of units which are create a noise problem. Silent closers should be fitted
themselves potential noise sources, for example, to doors.
children’s wards and outpatients’ departments, parts
7.3.4 Reduction of Noise by Structural Means
of which require protection against noise.
7.3.4.1 Insulation
7.3.2.1 Unloading bays, refuse disposal areas, boiler
houses, workshops and laundries are examples of Since the various departments or units maybe planned
service units which should be as far from sensitive areas in many ways, only general guidance on the insulation
as possible. values for walls and partitions is given as below:

7-3.2.2 The kitchen is a constant source of both air- a) It is recommended that walls or partitions
borne and structure-borne noise and should preferably between rooms should normally have a RWof
be in a separate building away from or screened from at least 40 dB. Higher values of RWof at least
the sensitive areas. If this is not possible and the main 45 dB are necessary where a noisy room is
kitchens must form part of a multi-storey building, adjacent to one requiring quiet conditions.
noise control is easier if they are placed below and not Doors should be solid with closefitting in the
above the wards and other sensitive rooms so as to frames.
facilitate the insulation of the equipment and machinery b) There is little insulation value in double swing
in order to reduce the transmission of structure-borne doors and where these are fitted to a noisy
noise to a minimum. room the opening should be planned so that
7.3.2.3 In ward units, the kitchens, sluice rooms, utility it is screened from areas requiring quiet by a
baffle lobby lined with absorbent material.
rooms, sterilizing rooms and other ancillary rooms,
Very high insulation values may be necessary
need to be placed quite near to the beds if they are to
fulfil their purposes, which are all sources of noise. in special cases and exceptional measures
Some form of noise baffling between open wards and may be required.
rooms of this kind will be needed. c) Solid floors with floating finishes and resilient
surfaces are necessary particularly between
7.3.3 Reduction of Noise at Source wards and other parts of the building.
In view of the difficulty of suppressing noise in hospital Ordinary timber board on joist floors should
buildings, it is important to eliminate noise at its source never be used.
wherever possible. d) Conduits, ventilation ducts, chases, etc,
should be constructed so as not to form easy
7.3.3.1 Use of resilient material by-pass for disseminating noise about the
Mats of rubber or other resilient material on draining building, and should be provided with
boards and rubber-shod equipment will greatly reduce sufficient sound insulation. Pipe ducts should
noise from utility rooms, sluice rooms and ward be completely sealed around the pipes where
kitchens. The use of plastics or other resilient materials they pass through walls or floors. Ducts
for sinks, draining boards, utensils and bowls would also carrying waste or water pipes should be lined
reduce the noise. Many items of equipment especially with sound insulating material to prevent
mobile equipment, such as trolleys and beds, may be noise from the pipes passing through duct
silenced by means of rubber-tyred wheels and rubber walls into the rooms through. which they pass.
bumper and the provision of resilient floor finishes 7.3.4.2 Absorption
(see 7.3.4.1). The latter also reduces footstep noise.
Silent type curtain rails, rings and runners should be Most surfaces in hospitals should be easily cleanable,
used. Lift gates and doors should be fitted with buffers so as to prevent the build-up of bacteria which may
and silent closing gear. Fans and other machinery should cause cross-infection. Many sound absorbent materials
be mounted on suitable resilient mountings to prevent of a soft nature and difficult to clean are unsuitable for
the spread of noise through the structure. use in some hospital areas and lose much of their
effectiveness, if painted for hygienic reasons.
7.3.3.2 Other measures
Some porous materials with very thin non-porous
Noise from water or heating pipes maybe reduced by coverings (like mineral wool covered with thin plastic
installing systems which operate at comparatively low sheets) have good sound absorption and when covered

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS. SOUND INSULATION AND NOISE CONTROL 17
with a perforated sheet metal facing can be used in the problems cannot be resolved by planning, the
most areas requiring a washable acoustical treatment. provision of double windows maybe necessary.
In noisy areas, such as corridors and waiting rooms,
8.3.2 Detailed Planning
however, a wider choice of absorbents is available.
8.3.2.1 Noise reduction within rooms
In the ward, bed curtains, window curtain etc, add
to the absorbent properties of the room and help The reverberation time should not exceed 1.0s in all
reduce reverberation in otherwise hard surfaced general offices of the types listed in 8.3.2.2 to 8.3.2.6.
surroundings. In small private offices, the reverberation time should
not exceed 0.75 second, in very large offices the
7.3.5 Sensitive areas such as operation theatres, reverberation time may be increased to 1,25 s. For
Doctors’ consultation rooms, intensive care units (ICU) canteens, the recommended maximum reverberation
require special consideration against noise control, time is 1.25 s.
Apart from outdoor noise, a common problem is the
transmission of sound between the consulting room 8.3.2.2 Lurge general ofices
and the waiting room. To ensure silence, a sound The grouping of departments and machines together
isolation DWof 45 dB (A), between the rooms shall be in one room should be avoided wherever possible.
provided. If the doors are directly connected by a single Where supervision is necessary the provision of glazed
communicating door it will not be possible to achieve screens carried up to the ceiling should be considered.
these values of isolation DW. To obtain 40-45 dB(A) If it is essential to the work of an office for machine
insulation between communicating rooms, it is operators and clerks to work side by side in the same
necessary to provide two doors separated by an air gap, room, the machines should be enclosed by panels or
such as a lobby or corridor. low screens lined with absorbent material and the
ceiling should be sound absorbent. In addition, the
8 OFFICE BUILDINGS
machines should be as quiet as possible in operation
8.1 General and mounted on suitable resilient mountings.

Modern office buildings are often noisier than older NOTE — A quiet area should be planned for prolonged
buildings due to the use of thinner and more rigid forms telephonic conversation.
of construction, harder finishes, more austere 8.3.2.3 Light weight construction
furnishings and use of business machines.
Modem construction methods and economy dictate the
8.2 Sources of Noise Nuisance use of light weight construction for many office
buildings. While the light weight materials lead to fast
8.2.1 Indoor Noise fabrication and erection and also effect considerable
Main sources of indoor noise include the following: economy in the building structure, they may lead to
tremendous sound insulation problems between
a) Office machines, such as typewriters, and adjacent offices and areas. Light weight construction
printers; is also frequently employed for the sub-division of
b) Telephonic conversation; large space into executive cabins and secretarial areas.
c) Noise from the public admitted to the building; Where sucti construction is considered desirable,
d) Footsteps, voices and slamming of doors in efforts should be made to provide a double-skin panel.
circulation spaces, lift doors and gates; The panels should be isolated from each other as far
e) Sound reproduction in staff training rooms, as possible either by the use of separate framing or by
conference rooms and recreation rooms, etc; the use of elastic discontinuities in the construction,
and a sound absorbing m~erial may be introduced in
f) Handling of crockery and utensils in canteeps
the air cavity between the’panel. The partitions should
and kitchens; and
be full height up to the bottom of the roof above and
g) HVAC and lift machine~. any openings required for air movement should be
provided with sound attenuators compatible with the
8.3 Recommendations
rest of the partition.
8.3.1 Site Planning
When light weight floors are provided in multi-use
Rooms demanding quiet conditions should be placed on buildings, adequate attention shall be paid to the
the quiet side of the site. Even on quiet thoroughfares, question of air-borne and structure-borne noise
these rooms should also not be planned at street level. transmission from the upper floors to the floors below.
They should also not be planned on enclosed yards used For effective reduction of air-borne noise, a double
for the parking of cars, scooters, etc. Where, however, panel hollow floor construction may be employed with

18 NATIONAL BUILDING CODE OF INDLA


some heavy sound damping material introduced air conditioning system can also be used to generate
between the panels and the panel isolated from each background masking noise if the noise level from the
other, The sound damping material could be sand, fans, ducts and grills is suitably tailored to generate
mineral wool, etc. In case impact noise isolation is also the desired frequency spectrum. However, it is not
required, the upper panel should be effectively isolated simple to predict the noise level of air conditioning
from the rest of the floors and building structure. The components accurately, On the other hand, the
choice of the isolation layer would of course depend electronic system enables both the level and the
upon the lowest frequency of interest. spectrum of the background noise to be accurately
adjusted to suit individual job requirements.
Another point to be kept in mind when going in for
light weight construction is to ensure that the light &3.2.5 Ojice equipment rooms
weight panels are not in resonance with the natural
Itis important that machines like typewriters, printer,
frequencies of any mechanical equipment installed
etc, should be quiet in themselves and also be fitted
inside the building. Light weight materials have high
with resilient pads, to prevent the floors or tables on
natural frequencies well within the audio range and
which they stand from acting as large radiating panels.
may resonate due to an applied vibratory
or vibrate
It is desirable to locate machines further apart and to
force. This vibratory force is caused by mechanical
apply sound absorbent treatment to the ceiling.
equipment, road traffic, rail traffic, etc. Special
measures also need be taken to isolate either the source 8.3.2.6 Banking halls
or the building so as to reduce the amount of vibration
If banking halls are large and lofty, noise nuisance
transmitted to the building structure.
tends to be aggravated. It is advisable to avoid high
8.3.2.4 Open plan ofiices reflective ceilings. The worst effects may be reduced
by segregating the noise from the quiet operations and
A new concept in office planning is the use of open
screening one from the other and by applying sound
plan offices. Large open floor spaces are converted
absorbent materials to the surfaces of the ceilings,
into an office area with senior executives, junior
screens and nearby walls. Resilient flooring is also
executives and secretarial staff all seated within the
recommended.
same area without the use of any partitions or walls.
While this method of planning is appreciated, it leads 8.3.2.7 Public ofices and waiting spaces
to a problem of inadequate acoustical privacy between
Noise nuisance may be minimized by the provision of
adjacent work spaces. Speech privacy in open plan
resilient flooring, sound absorbent ceilings and heavy
offices is defined by the speech interference level of
full height screens between the public space and the
intruding noise. Speech privacy between two adjacent
clerical office.
rooms or spaces is, therefore, a function of two key
parameters; noise reduction of the intervening partition 8.3.2.8 Canteens
and background noise levels.
The provision of a sound absorbent ceiling, resilient
Special design measures are, therefore, required to flooring and the use of plastics trays and tables with
reduce the level of intruding sounds at workplaces to ‘quiet’ tops are recommended,
acceptable low value so that people are not disturbed
8.3.2.9 Circulation spaces
{ and adequate privacy is maintained. Some special
; measures which might be considered for such open The effective length of long corridors should be limited
plan offices are the use of an acoustical ceiling together by providing swing doors at intervals. Hard floor
with partial height barriers between work spaces, all finishes and board and batten floors in corridors should
designed to provide adequate privacy between adjacent be avoided. The provision oja sound absorbent ceiling
i work spaces. In addition use may have to be made of in corridors is recommended. Floor ducts should be
) an electronic background masking noise system which planned on one side of corridors.
\ provides a constant level of a generally acceptable
The noise from slamming of doors maybe reduced by
background noise in the entire ot%ce area. The masking
fitting automatic quiet action type door closers. Door
noise system is a very useful concept in open plan
buffers are useful but may reduce insulation of air-
office design because by raising the background level
borne sound due to the inevitable gaps between buffers.
at every workplace, intruding noises are made less
Continuous soft, resilient strip let into the door frames
disturbing. A background music system cannot serve
is preferable. The use of quiet action door latches is
as a noise masking system because the music does not
recommended.
have a constant spectrum or sound level. In fact the
background noise masking system must be introduced Staircases and lifts should be isolated from quiet rooms
gradually without the knowledge of employees. The and should have silent type doors.

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 19
8.3.3 Requirement of Sound Insulation 8.3.3.3 It is recommended that the minimum sound
reduction index, RW for floors should be 45 dB, and
With opeti window (single or double) the sound
the floors should have a resilient finish.
reduction (DW) will be 5- 10dB, and with sealed double
windows it will be 40-45dB. Intermediate values are 9 HOTELS AND HOSTELS
obtainable with closed openable windows (single or
double) but only, of course, at such times as ventilation
9.1 General
may be dispensed with. Having to choose between Hotels and hostels are primarily used as dwelling units,
ventilation and noise exclusion is a serious handicap and hotels also provide for public entertainment. The
to efficient working in offices. In large office blocks most serious risk of course is disturbance to sleep, and
on noisy sites, consideration should be given to the adequate care, therefore, need be taken to protect the
provision of sealed double windows and mechanical occupants from being disturbed by outdoor and indoor
ventilation at least in the offices on the sides of the noise.
building exposed to noise.
9.1.1 Outdoor Noise
8.3.3.1 The insulation necessary between adjoining
rooms, both horizontally and vertically, depends upon Hotels near railway stations, airports, highways and
the amount of noise created within the rooms, the those situated in highly urbanized areas are specially
amount of intruding noise and whether it is important vulnerable to outdoor noise. The outdoor noise in many
that conversation should not be overheard between of the areas is of a high level even late at night and in
rooms. Generally a sound isolation value (DW) of 30 the early morning. The noise could also be due to other
dfl between one room and another room in office is types of activities such as building construction activity .-
recommended. (pile driving, concrete mixing etc) and various types
of portable utility equipment, such as compressors or
8.3.3.2 The following list may be considered as broad generators.
classification of noise producing rooms and rooms
requiring quiet though many offices fall into both 9.1.2 Indoor Noise
categories. Where rooms in opposing categories are In so far as indoor noise is concerned, the noise could
planned adjacent to each other, a sound reduction (DW) be due to the occupants themselves, which is transmitted
of at least 45 dB should be provided between them. from one room to the other. It could also be due to public
fimctions and late night use of restaurants located in the
Noise Producing Rooms Requiring Quiet
hotel as also due to miscellaneous utility equipment
Rooms Conditions
installed for providing and maintaining the services in
Entrance halls, staircases Executive’s rooms,
the hotel, such as, air conditioning equipment, pumping
and corridors used by the Conference rooms and
public Board rooms equipment, power laundry and kitchen. Sometimes
Lifts and lift halls Interview rooms hotels equipped with standby generators are a potential
source of noise. Another source which could lead to
Motor and plant rooms Offices for one or two
persons disturbance to the occupants is the plumbing.
Lavatories Medical officer’s rooms 9.2 Recommendations
Public offices Sick rooms
9.2.1 Site Planning
Canteen and kitchens Rest rooms
Office machine rooms and Libraries While it is desirable to locate the hotel, or hostel away
typing pools from an area where there is a high ambient noise level,
Recreation rooms Telephoning rooms many a time these have to be located in noisy areas for
Large general offices public convenience. Hote3s near airports and railway
stations are becoming popular because they are
Cinemas and projection
rooms convenient for passengers in transit. Hotels located in
D. the commercial areas of a city are also a commercially
a) rooms requiring quiet (as listed 45 m viable proposition and many a time this factor
above) on ~ qui~t si~e where privacy outweighs the other problems associated with such a
is required location. When a reasonably quiet location is not
b) Rooms requiring quiet (as listed 40 dB possible, it is desirable that adequate measures be
above) but on a noisy site or where considered to provide a comfortable acoustical
a lower degree of privacy is
environment for the occupants.
tolerable
c) Clerical offices in which noise does 20-30 dB 9.2.2 Internal Planning
not constitute a major nuisance
Where a hotel is located in a noisy environment, the

20 NATIONAL BUILDING CODE OF INDIA


provision of sealed windows (single or double) and between rooms. Suitable acoustical lining would need
provision of an air conditioning system is desirable to be provided in the ducts consistent with the fire
for rooms exposed to noise. The requirements for the safety requirements of the buildings.
windows would of course depend upon the level and
9.2.2.6 Large hotels often have banquet halls and
character of noise in the area.
conference halls which are separately, hired out for
The general recommendations for satisfactory public and private functions. Late night restaurants and
acoustical design of hotels and hostels are given night clubs are also popular and functions in all these
in 9.2.2.1 to 9.2.2.7. areas may go on well into the night. It is therefore
essential that these rooms be effectively isolated from
9.2.2.1 Hotels of all classes shall by necessity provide
bedrooms and effective insulation from all possible
good protection against indoor noise. Since hotels can
noise source is.considered. Here it is not only necessary
be considered as flats, the standards of protection
to consider the air-borne sound insulation but it is also
recommended for flats are also applicable to hotels.
necessary to consider the question of structure-borne
Partition between guest rooms and between rooms,
and impact noise transmitted from areas where there
corridors and floors shall not be less than 115 mm brick
might be dancing late into the night.
wall plastered or equivalent. The floors shall have
proper impact insulation. Special attention should be 9.2.2.7 While most of the noise problems encountered
paid to built-in wall cupboards as these are potential in hotels are applicable to hostels, the latter are
areas of sound leakage. These will not serve as sound normally of more economical construction and,
insulating partitions and may not be relied upon to therefore, cannot cater for special sound insulation
increase the insulation value of partitions against which provisions. However, as far as possible, precautions
they may be built. In fact, partitions between adjoining should be taken to provide comfortable conditions in
rooms should be continuous behind the cupboards. Use hostel rooms. This is specially true for student hostels
of silent type door gear and cupboard catches is also where each room is also a living room. Students might
highly desirable. play music or have loud discussions late into the night.

9.2.2.2 Door openings on opposite sides of corridors This may disturb sleep or study of other students.
shall be staggered and doors be provided with gaskets Proper precautions should, therefore, be taken to
on head, sides and threshold. Inter-communicating doors provide satisfactory conditions.
should be double doors, fully gasketed. Doors should
10 INDUSTRIAL BUILDINGS
also have quiet action latches. Whenever possible, rooms
should be entered through a baffle lobby. Wherever 10.1 General
possible, corridor walls should not have ventilators
Industrial buildings are primarily producers rather than
unless they are double glazed and non-openable.
receivers of noise. The level of industrial noise
9.2.2.3 Corridors and staircases may have resilient commonly exceeds that from any other source with
floor coverings and sound absorbent ceilings are the exception of aircraft. As compared with traffic
desirable unless the corridor is fully carpeted. noise, its effects are less widespread but it is often more
Staircases and lift wells may be cut off from corridors annoying in character.
by means of swing doors and, if possible, isolated from
10.1.1 Many industrial noises contain very strong high
guest rooms by linen stores or similar rooms. Room
frequency whines, screeches and clatter — these
service pantries on floors can also be a source of noise
components are relatively more attenuated by passage
and may be separated from corridors by baffle lobbies,
through the air and by the, insulation of light structure
unless the rooms themselves have baffle lobbies.
than are lower frequencies.
9.2.2.4 Except within the same suite, bathrooms
10.1.2 Intermittent noises a&either isolated explosions
should not be planned next to bedrooms. Where this is
or reports, or noises of a periodic nature, such as those
unavoidable, internal pipe shafts with heavy walls,
of pressure relief valves of blow off, or the noises of
unpierced on bedrooms side maybe used as means of
work occurring at random intervals, for example,
separation. It is important to choose quiet type of
hammering, grinding and sawing operations; the latter
sanitary fittings and to design the plumbing system so
class may be especially irritating because of high
as not to create noise, that is by avoiding sharp bends,
frequency components.
restrictions of flow, quick-action valves that might
cause water hammer, etc. 10.2 Sources of Industrial Noise
9.2.2.5 Air conditioning system should be quiet in 10.2.1 Noises in industrial buildings are mainly of
operation. Care should also be taken that the air indoor origin. Noise in factories and workshops is
conditioning ducts do not lead to a cross-talk problem generally caused by machine tools and by operations

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 21
involved in making and handling the product and they in permanent noise induced hearing loss in the course
are classified into the following groups, depending of time. Damage-risk criteria specify the maximum
upon how the noise energy is generated. levels and duration of noise exposure that may be
considered safe. Generally accepted damage-risk
10.2.1.1 Impact
criteria for exposure to continuous, steady broadband
Noise caused by impact is the most intense and noise are shown in Table 7. Whenever the sound levels
widespread of all industrial noises. It is normally at the workers position in a factory exceed the levels
coupled with resonant response of the structural and the duration suggested, feasible engineering
members connected to the impacting surface. Common controls shall be utilized to reduce the sound to the
sources of this type of noise are forging, riveting, limits shown. such controls fail to reduce sound
If
chipping, pressing, tumbling, cutting, weaving, etc. levels within the levels of Table 7, personal hearing
Intense impact noise may also be produced during protection equipment shall be provided and used to
handling of materials as in the case of sheared steel reduce sound levels within the level shown.
plates falling one over another in collecting trays in a
10.3.2 Inte~erence with Communication.
steel factory. Impact noise is usually intermittent and
impulsive in character, but it may also be continuous In factories where audible warning signals are used,
as in the case of tumbling. or where an operator follows the operation of his
machine by ear, the background noise should not be
10.2.1.2 Friction
so loud as to mask the signal or desired sound (the
Most of the noise due to friction is produced in such information sound) to be heard. Noise maybe the cause
processes as sawing, grinding and sanding. Friction of accidents by hindering communication or by
also occurs at the cutting edge on lathes and other masking warning signals.
machine tools and in brakes and from bearings. The
10.4 Methods of Reducing Noise
spectrum of frictional noise often predominates in high
frequency and is very unpleasant in character. 10.4.1 Noise Control by Location
10.2.1.3 Rotation and reciprocation Machines, processes and work areas which are
A ro~ating or reciprocating machine generates noise approximately equally noisy should be located together
due to unbalanced forces and/or pressure fluctuations as far as possible. Areas that are particularly noisy
in the fluids inside the machines. In many cases, the should be segregated from quiet areas by buffer zones
moving surfaces radiate noise directly and in other that produce and may tolerate intermediate noise levels.
cases, the pressure fluctuations are transmitted to the 10.4.2 Noise Reduction by Layout
outer casings of the machine from where they are
radiated as noise. Interaction of rotating component The office space in a factory should be as far as possible
with the fluid stream can also give rise to pure tone located preferably in a separate building. This building
components, such as the whine in a turbine. Since most should not have a wall common with the production area.
machine casings have radiation efficiencies of unity Where a common wall is unavoidable, it should be heavy
in the higher frequency range, the amount of sound with few connecting dqors and no permanent openings.
radiated is often substantial. 10.4.3 Noise Reduction at Source
10.2.1.4 Air turbulence 10.4.3.1 Selection of mqchine~
Noise may be generated by rapid variation in air Noise should be reduced as near the source as possible.
pressure caused by turbulence from high velocity air,
While the operational processes in a factory may be
steam or gases. Common examples are the exhaust fixed and may have no,quieter alternative, careful
noise from pneumatic tools and air jets. The noise is selection of the machine tools and equipment to be
intense, and broad based in character and the frequent y used may considerably help attaining lower noise levels
criteria depends on the size of the jet. The intensity in the machine shop.
increases rapidly with the velocity of the air stream.
10.4.3.2 Reducing noise from potential sources
10.2.1.5 Noises with pure tone components
Impact that is not essential to a process should be
Whining noise from turbines and humming noise from quietened. Noise from handling and dropping of
transformers come under this group. materials on hard surface maybe reduced by using soft
10.3 Noise Criteria resilient materials on containers, fixing rubber tyres on
trucks, trolleys, etc. Machine noise may be kept to a
10.3.1 Hearing Damage-Risk Criteria
minimum by proper maintenance. Proper lubrication will
Continuous exposure to high noise levels may result reduce noise by friction conveyors, rollers, etc.

22 NATIONAL BUJLDING CODE OF INDIA


Table 7 Permissible Exposure Limits for 10.4.3.3 The noise from the radiating surfaces may
Steady-State Noise be reduced by reducing the radiating area. For example,
if the area is halved, the noise intensity will be reduced
(Clause 10.3.1)
by 3 dB and at low frequencies the reduction will be
Sound Level dB(A) Time Permitted, T much greater.
(Slow Response) h rnin
(1) (2) 10.4.3.4 Supporting structures for vibrating machines
and other equipment should be frames rather than
85 16-00
cabinets or sheeted enclosures, If an enclosure is used,
86 13-56
87 12-08
precaution should be taken to isolate it and line it on
88 10-34 the inside with sound-absorbent material. The noise
89 9-11 radiated by machinery guards can be minimized by
90 8-00 making them of perforated sheet or of wire mesh.
91 6-58
92 6-04 10.4.3.5 Reducing transmission of mechanical
93 5-17 vibration
94 4-36
95 4-00 A vibrating sources does not usually contain a large
96 3-29 radiating surface but the vibration is conducted along
97 3-02 mechanically rigid paths to surfaces that can act as
98 2-50
effective radiator. If the rigid connecting paths are
99 2-15
100 2-00 interrupted by resilient materials, the transmission of
101 1-44 vibration and consequently the noise radiated may be
102 1-31 greatly reduced, The reduction depends on the ratio of
103 1-19 the driving (forcing) frequency of the source to the
104 1-09
natural frequency of the resilient system. The natural
105 1-00
106 0-52 frequency may be determined from static deflection
107 0-46 under actual load as given in Fig. 1. Higher the
108 0-40 ratio between the two frequencies, lesser is the
109 0-34 transmissibility, which is defined as the ratio of the
110 0-30
force transmitted through the resilient isolator to the
111 0-26
112 0-23
exciting force applied to it. Transmissibility and the
113 0-20 equivalent noise reduction for various frequency ratios
114 0-17 are given in Fig. 2. For satisfactory operation, a ratio
115 0-15 of 3:1 or more between the driving and natural
frequencies is recommended.
NOTES
1 Where the table does not reflect the actual exposure times 250.00
and levels, the permissible exposure to continuous noise at a
single level shall not exceed the time T (in hours) computed 125.00
from the formula ff 75.00
16 E 50,)0
T=
2 [0.2 (L–85)] t
z
where g 25.00
~
L is the work place sound level measured in dB(A).
~ 12.50
2 When the daily noise exposure is composed of two or more
periods of different levels, their combined effect should be rz 7.50
considered rather than the individual effect of each. The g 5“W
combined levels may not exceed a daily noise dose, D of unity
where D is computed from the formula: “ 2.50
$
~ 1.25
5 0.75
where, C,, Cz .. . ... ... . .. C“ indicate the total duration of 0.50
exposure (in hours) at a given steady-state noise level; and Tl,
T2, T, are the noise exposure limits (in hours) for the 0.25
respective levels given in the table or computed by the equation 04 8 12 16 20 24 283032
in Note 1. Exposure to continuous noise shall not exceed
115 dB(A) regardless of any value computed by the formula NATURAL FREQUENCY IN l-k
for the daily noise dose, D or by the equation given in
FIG. 1 RELATION BETWEEN STATIC DEFLECTION
Note 2.
AND NATURAL FREQUENCY

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 23
1.00 chosen to produce enough deflection for

5.00
3.00
I the isolation require@ and shall be such
that at this deflection, it is not loaded
beyond its elastic limit.
2.00 b) Position of Isolator — The normal position
~ 1.00 0 of the isolators is between the machine and
its foundation. However, if the forcing
:
g
0.50
0.30 i 8
frequency of the machine is low (less than
10 H ) and vibration isolators with the
requi;ite deflection for this location are not
%! 0.20 14
i! available, the machine may be bolted directly
1- 0.10 20 to ~ independent heavy inertia concrete base
0.05
0.03
. 28
and the available vibration isolators used
below the concrete base.

0.02 34 1) Large press and drop hammers which


create serious impact vibration in heavy
0.01 machine shops may be mounted rigidly
01234567
on very massive blocks of concrete
having weights several times greater than
~T,O FORCING FREQUENCY
the weights of the supported machines.
NATURALFREQUENCY
[ 1 The inertia blocks may, in turn, be
FIG. 2 TRANSMISSIBILITY
ANDEQUIVALENTNOISE isolated from the building structure by
REDUCTIONFORDIFFERENTRATIOSOF FORCING large wooden blocks and with thick pads
ANDNATURALFREQUENCIES of cork.
2) In critical installations (see Note), attempt
Materials for isolators and their position are given
should be made to locate the resilient
below:
mounts in a plane which contains
a) Material for Isolators — Vibration isolators the centre of gravity of the mounted
are usually made of resilient materials like assembly. It is also preferable to locate
steel in the form of springs, rubber cork and the mounts laterally as far away as
felt. possible from the centre of the machine.
1) Because of the large range of deflections NOTE — Critical installations are those
obtainable in coil springs, they may installationswheretransmissionof vibrationfrom
isolate vibrations over a large spectrum these installations will seriously hamper the
of low frequencies. Metal springs transmit normat working.
high frequency (from about two hundred 3) Rigid mechanical ties between vibrating
to several thousand c/s) very readily. machine and building structure, short-
Transmission of these frequencies can be circuit or reduce the effectiveness of
reduced by eliminating direct contact isolators. Loose and flexible connections
between the spring and the supporting should be inserted in all pipes and
structure. Rubber or felt pads may be conduits leading from the vibrating
inserted between the ends of the spring machine. Where flexible connections are
and the surfaces to which it is fastened. impracticable, bends should be inserted
2) Rubber in the form of pads maybe used into the pipe& or the pipes themselves
to isolate very effectively engines, should be supported on vibration mounts
motors, etc. It maybe used in compression for a considerable distance from the
or in shear. Some rubber mountings use source.
rubber-in-shear as the primary elastic 4) Flexibility of foundation — The effect
elements and rubber-in-compression as of flexibility of the foundation on
a secondary element which furnishes the isolator transmissibility shall be
snubbing action if the mounting is considered in the selection of practical
subjected to an overload. vibration isolating mountings. The
3) Felt or cork or both may be used as simplified vibration isolation theory
resilient mats or pads under machine assumes a completely rigid foundation.
bases. The load per unit area shall be However, in practice, this can never be

24 NATIONALBUILDINGCODE OF INDIA
achieved. The foundation is never of the enclosure is open, the reduction maybe increased
actually completely rigid. Generally, the by placing sound-absorbing material on the ceiling
relatively low stiffness of the isolation overhead.
system permits the assumption of the
10.4.5 Acoustical Absorption Devices
foundation to be rigid. However, if the
stiffness of the isolator is allowed to 10.4.5.1 Acoustical treatment of ceilings and side
become comparable to the foundation walls
stiffness (or greater), the deflection of
In order to reduce the general reverberant noise level
the isolator will become smaller and
in machine shops, acoustical material may be placed
the foundation will also deflect with
on the ceiling and side walls. With this treatment 3 to
increased transmissibility and decreased
6 dB reduction of middle and high frequency noise
isolator efficiency. In a dynamic sense,
may be achieved. While the noise level at the source,
supporting foundation or floors should
affecting the operator, may not be reduced materially,
have natural frequency as high and be as
the treatment would bring down the general noise level
stiff as possible compared to the system
away from the source in reverberant field.
being isolated. Good design practice
requires that the isolators should be 10.4.5.2 Functional sound absorbers
designed assuming a rigid foundation
For efficient noise reduction ‘functional sound
with the stipulation that the selected
absorbers’ may be clustered as near the machines as
machine isolation system frequency
possible. These units may be suspended and distributed
should be well below the foundation
in any pattern to obtain lower noise levels within the
frequency. This point should specially be
machine shop. Compared on the basis of equal total
kept in mind when installing ,machines
exposed surface areas, functional sound absorbers have
at upper levels in buildings because
higher noise reduction coefficients (NRC) than
supported slabs generally have lower
conventional acoustical materials placed directly on
natural frequencies (low stiffness) than
ceilings and walls.
slabs on grade in basement or ground
floor locations. 11 LABORATORIES AND TEST HOUSES
10.4.4 Noise Reduction by Enclosures and Barriers 11.1 Sources of Noise
10.4.4.1 Enclosures 11.1.1 Outdoor Noise
Air-borne noise generated by a machine may be In a test house or laboratory, where research workers
reduced by placing the machine in an enclosure or and scientists are engaged in performing sophisticated
behind a barrier. The enclosure maybe in the form of experiments, the external noise is mostly contributed
close-fitting acoustic box around the machine such that by noise emitting buildings (workshops, machine
the operator performs his normal work outside the box rooms), airports, railway stations and general traffic
and thus is not subjected to the high noise levels of the noises. The outdoor sources of noise in a college
machine. The enclosure may be made of sheet metal laboratory include noises produced in a playground as
lined inside with an acoustical material. well.
Where size of the machine, working area and the 11.1.2 Indoor Noise
operation do not permit close-fitting enclosures, the
machine may be housed in a room of its own. The The following sources mainly contribute to indoor
inside of the enclosure should be lined with sound- noises in research institutions/college laboratories:
absorbing materials to reduce the noise level of the a) Workshops, machine rooms, cafeteria, etc;
contained sound. The bounding walls of the enclosures b) Air-conditioning and exhaust fans;
shall also have adequate transmission loss to provide
c) Noise produced within the test house or
desired insertion loss.
laboratory while performing experiments;
10.4.4.2 Barriers and
d) Typing or other machine noises, telephone
A partial reduction of noise in certain directions may
service, lift, sanitary services, etc.
be obtained by ‘barriers’ or partial enclosures or partial
height walls. Two-sided or three-sided barrier, with or 11.2 Recommendations
without a top and invariably covered on the machine
11.2.1 Site Planning
side with acoustic absorption material should face a
wall covered with sound-absorbing material. If the top While planning for a laboratory or test house, care

PARr 8 BUILDINGSERVICES— SECTION 4 ACOUSTICS,SOUNDINSULATIONANDNOISE CONTROL 25


should be taken in the design that no noise emitting 12 MISCELLANEOUS BUILDINGS
installations should exist in its neighborhood.
12.1 Law Courts and Council Chambers
However, where outdoor noises exist, such as from
local factory, heavy traffic airports, railway lines, sport It is important that law courts and council chambers
grounds or busy markets, buildings should be kept as be protected from the intrusion of outdoor noise and
far away as possible from the source of noise. from indoor noise arising both from ancillary ofllces
and circulation spaces. The general recommendations
11.2.1.1 The window and door openings towards the
on site planning given in 3 apply to law courts and
noise sources should be minimum. Minimum amount
municipal buildings, but in the larger buildings at least,
of glazing should be placed on walls directly facing
further protection against outdoor noise can be obtained
the noise sources.
by planning offices and other rooms around the court
11.2.2 Internal Planning rooms or chambers, and separating the offices from
11.2.2.1 Noisy places should be kept separate from the central rooms by means of corridors. This
the quiet ones. The location of laboratories or test arrangement is usually convenient to the function of
houses should be so chosen that it is cut off from the the buildings.
noisy zones. Where there are offices attached to a 12.1.1 The wall between the corridors and the central
labomtory, provision should be made to treat the ofilces rooms should have a sound reduction index, RW of not
and to use acoustical partitions, to achieve a sound less than 50 dB (for example 230 mm brick) to insulate
isolation DW of at least 35 dB. against air-borne noise in the corridors. Entrances from
11.2.2.2 In a laboratory, mostly hard reflecting halls or corridors into courtrooms or council chambers
surfaces and bare furnishings are found, which should be through baffle lobbies with two sets of quiet
produce very reverberant conditions. The noise action doors. Sound absorbing treatment on ceilings
condition still deteriorates when noise producing and upper parts or walls or entrance lobbies is
instruments are switched on or a heavy object is recommended.
dropped on the floor. Under these conditions, sound
12.1.2 The whole of the floor of the court room or
absorbing treatment of the space is very essential.
chamber includlng steps and seating areas set aside
Sound absorbing ceilings are recommended to deaden
for the public should have a resilient floor finish to
such noises. Rubber buffers may also be fitted to the
reduce the noise of footsteps and shuffling of feet. Any
legs of furniture.
tip-up seats should be quiet in action.
11.2.2.3 In large span laboratories or test houses where
12.1.3 Sound absorbing treatment applied for acoustic
scientists and researchers m-e engaged in work and/or
purposes serves also to reduce the build-up of noise
simultaneously busy in calculations or desk work
within the room and, part of the treatment should be
requiring high degree of mental concentration, use of
applied in a band to the perimeter of the ceiling to
sound absorbing screens is recommended.
absorb intruding outdoor noise. It is often desirable to
11.2.2.4 Noise reduction between the test house or keep the centre part of the ceiling free of absorbent
laboratory and corridors or general circulation space material for acoustic reasons.
should be well kept in mind and due care should be
taken of the type of doors and the manner of their 12.2 Libraries, Museums and Art Galleries
fittings etc. Transmission of noise through service Quiet conditions for reading and study are essential
ducts, pipes, lifts and staircases should also be guarded. in these types of buildings and, since their occupancy
Telephones should preferably be placed in a separate is not noise producing, intruding noise is more
small enclosure or acoustically efficient telephone noticeable and distracting. Every opportunity
booth. therefore should be taken to plan for noise defence,
both in respect of siting of the building and internal
11.2.2.5 To isolate a laboratory or a test house from planning. When possible, stack rooms, store rooms
structure borne noises originating from upper floor, and administrative offices should be planned to screen
sandwich type floor construction is recommended. reading rooms, print rooms and lecture rooms from
11.2.2.6 Wherever the provision of double glazed noise sources. In public libraries, the reference library
windows is necessary to reduce the heat losses, care and lecture rooms should receive first consideration;
should be taken to provide sealed double windows the lending library, newspaper and periodical rooms
rather than double glazing in a single window. have a higher background noise and are secondary in
importance.
NOTE— Doubleglazed windowsfor soundinsulationshould
have a minimumgap of 100mm betweenthe two glasses. 12.2.1 In large libraries, museums and art galleries

26 NATIONALBULLDINGCODE OF INDIA
echoes from lofty, large domed or concave ceilings otherwise be given full value. Therefore, sites at cross-
are often a nuisance. Small noises such as footsteps, roads or close to steel railway bridges, religious places
coughs, chair scraping and closing of books are or near churches where bell ringing is practiced, should
reinforced by reverberation, and concave surfaces even be avoided unless very high standards of structural
when treated with a sound absorbent may focus these sound insulation are contemplated. Sites adjoining
noises. Treated flat ceilings, if not too high, obviate underground railways may also prove unsatisfactory
these troubles. Books on shelves in libraries constitute at basement levels owing to low-pitched noise or
a valuable wall absorbent. rumble transmitted through the ground; special
isolation measure need to be adopted for isolating large
12.2.2 Floor finishes are important. The impact noise
buildings from ground vibration of this sort.
of footsteps on marble, terrazzo or wood block
flooring, and especially on hardwood strip and batten 12.3.2 Whenever possible, for concert halls and
flooring, can be disturbing both within the room in theatres on city sites a noise survey of the site should
which the noise is generated and the rooms below. On be made; a suitable sound reduction value for the
solid floors, resilient floor finishes, such as rubber, cork structure of the building can then be chosen so as to
and linoleum on an underlay, are highly desirable. In keep down to certain maximum noise levels within the
the children’s sections of libraries and museums they auditorium. The maximum octave-bad sound pressure
are essential. In existing buildings, rubber linoleum or levels (SPL) recommended are given in Table 8.
vinyl asbestos tiles laid over the floor in the traffic
Table 8 Maximum Sound Pressure Levels Due
areas are often a solution to the problem,
to External and Meehauical Equipment
12.2.3 Reference libraries in universities, research Noise in Auditoria (dB)
establishments, office buildings and science buildings (Clause 12.3.2)
having machines and testing benches, should be
Type of Centre Frequency (Hz)
planned in a quiet part of the building, Walls
A“~tofi”” ~
enclosing the library should normally have a sound
63 125 250 500 1000 2M10 40008000
reduction index, RW of not less than 50 dB (for
ConcertHatls 51 39 31 24 20 17 14 13
example 230 mm brick) and baffle lobbies should be [dB(A)-25]
planned between the library and halls and corridors.
DramaTheatres 55 44 35 29 25 22 20 18
Walls facing on to corridors or other noisy areas and Cinemas
should not have fanlights unless they are double [dB(A)-30]
glazed and non-operable.
12.3.3 The minimum standard of sound reduction
12.3 Auditoria and Theatres index, RW likely to be required for the envelope of an
The sources of noise that have to be considered in auditorium in a city to protect it against external noise
concert halls, opera house, theatres and similar is of the order of 65 dB for a concert hall or 55-60 dB
auditorium buildings are as follows: for a theatre. This reduction should be provided on all
sides, but it would be reasonable to make the RW for
a) Outdoor noise entering through walls, roofs, the roof 5 to 10 dB less provided the building is not
doors, windows or ventilation openings; unduly exposed to noise from aircraft in flight.
b) Noise from any other hall in the same Surrounding the auditorium with ancillary rooms and
building, especially if let out separately for foyers is an obvious and invaluable planning method
revenue; of obtaining the required insulation against outdoor
c) Noise from foyers, service rooms and other noise.
ancillary rooms, particularly rehearsal rooms;
12.3.4 Ventilation intakes and returns are vulnerable
and features in the defence against external noise. They
d) Noise from air conditioning plant, etc, and should be positioned so as to avoid exposure to noise,
the cross-transmission of other internal noises and in addition sufficient length of both inlet and outlet
via ventilating duct system. ducts should be provided with carefully designed
12.3.1 Because of greatly increased outdoor noise, all silencers. The ventilation system should also be
auditorium buildings now need more care in siting than designed to avoid transmitting or adding to internal
formerly. For listening to speech or music, a very low noise.
background noise level is desirable; in concert halls 12.3.5 The most serious internal noise problem arises
especially the quietest possible conditions should be when there are two halls meant for separate use in the
provided because the pauses and moments of silence same building, especially if one of them is a concert
which are an essential element of music cannot hall. The latter is a very loud potential source of noise

PART 8 BUILDINGSERVICES— SECTION 4 ACOUSTICS,SOUNDINSULATIONANDNOISE CONTROL 2’7


and requires a high standard of protection against in Table 9. Cinema design, however, normally requires
extraneous noise. In these circumstances it is doubtful specialist acoustic advice.
whether a ‘single’ wall can be adequate for insulating
the two halls unless it is designed with a wide unbridged Table 9 Typical Sound Insulation Specification
cavity. Separation by planning is preferable. for Wall Separating Two Cinema Screens
(Clause 12.4)
12.3.6 Other sources of internal noise are rehearsal
rooms, scenery bays and workshops, stages of other Octave Band Sound Reduction Index
halls where rehearsals or erection of stage sets might Hz R, dB
be in progress and foyers and bars where loud 63 38
conversation might occur. The insulation of the internal 125 44
250 50
walls should be adequate to protect the auditorium from
500 61
these noise sources and the insulation should not be 1000 57
by-passed by openings, doorways, etc. The general 2000 58
noise due to banging of doors also needs to be taken 4000 57
care of; soft sealing materials should be provided for 8000 55
all doors to ensure quiet closing.
13 NOISE FROM BUILDING SERVICES
12.3.7 For detailed acoustical design of auditoria and
ccmference halls reference may be made to good 13.1 Mechanical, electrical, air conditioning, heating
practice [8-4(3)]. and mechanical ventilation, and other services are
provided in almost all large buildings excluding
12.4 Cinemas
residential, commercial and industrial buildings. Noise
The main objective of the design should be to control control measures should be incorporated during the
noise from adjacent screens, the projection area, the design and installation of such services to adhere to
foyer, and outside the cinema. The first of these, the recommended outdoor and indoor noise criteria for
controlling noise from adjacent screens, is likely to be the kind of occupancy. For detailed design of noise
the most difficult with modern digital sound systems. control for services, specialist advice should be sought.
As most cinemas are air conditioned, there will be some
Some basic design techniques for noise control in air
noise from services. To ensure reasonable listening
conditioning, heating and mechanical ventilation
conditions, this should be limited to 30 dBA. This will
system are given in Annex G.
provide some masking of the noise from adjacent
screens, but a high performance partition will still be 13.2 Control of noise from mechanical equipments
essential. Masonry or lightweight construction maybe can also be done by specifying noise control
used, and a typical performance specification for a requirements while purchasing the equipments (see
lightweight wall separating two screens is given Annex H).

ANNEX A
(Clause 2.4)
NOISE CALCULATIONS

A-1 GENERAL L c = 10 log,. (HWo + loL2/lo)


Some of the simpler types of noise calculation are As the individual sound pressure levels are logarithms
described in this Annex. of the mean square sound pressures, they cannot
simply be added arithmetically. Figure 3 shows a
A-2 ADDITION OF TWO NOISE LEVELS
graphical method for adding the sound pressure levels
To determine the combined sound pressure level (LJ from two independent sources to obtain the combined
resulting from the sound pressure levels of two or more sound pressure level at a particular place. This graph
noise sources (Ll, Lz, etc), it is necessary to calculate may also be used for multiple sources by combining
and add the mean square values of their individual sources two at a time to produce virtual sources that
sound pressures and then convert this back to a sound can then be combined. The most accurate approach
pressure level. This can be done using the following is to start with the lowest levels and work towards
folmlda: the highest.

28 NATIONAL BUILDING CODE OF INDIA


.
IK .-I I . +m.- >— ). . . . . . L. b -. .,. -.... —.- .—.,-——— . . . . . . .. ——. .——

?):.

A-4 NON-UNIFORM COMPOSITE PARTITIONS

Figure 5 how to calculate the overall sound insulation


l\
7

1 of a composite partition consisting of two parts having


1 \‘ different sound — insulating properties, for example
a window in a wall. It may also be used to give an
indication of the effect of gaps or holes in a partition
by assigning a sound insulation value of O dB to the
aperture.

A-5 A-WEIGHTING CALCULATIONS

The equivalent A-weighted level is often required when


data on a noise source is available as a set of octave
band or one-third octave band levels. The conversion
can be done manually, using the standard A-weighting
o~ I values (Table 10) and the graph for combining levels
012345678910 1112131415
(Fig. 3). For all but the simplest situations it is more b
DIFFERENCE BETWEEN LEVELS (IN dB) convenient to use a computer spreadsheet to do the
conversion.
FIG. 3 THE ADDITIONOF Two NOISELEVELS

The graph should be used with caution where the noise Table 10 Standard A-Weighting Values (dB)
sources are not independent. For example, the sound Third Octave A-Weighting Third Octave A-Weighting
pressure level from two large transformers fed with Band Center Band Centre
currents in phase will be very sensitive to the receiving Frequency Frequency
Hz dB Hz dB
position. This is because the effect of the constructive
(1) (2) (3) (4)
and destructive interference of the sounds from the two
sources is very dependent on position. 10 -70.4 500 -3.2
12.5 -63.4 630 –1.9
16 -56.7 800 -0.8
A-S SUBTRACTION OF TWO NOISE LEVELS
20 -50.5 1000 0
25 44.7 1250 0.6
When measuring noise from a source, the true noise
31.5 -39.4 1600 1.0 4
level of the source alone will be less than that shown 40 -34.6 2000 1.2
bv the meter if the level of extraneous noise is less 50 -30.2 2500 1.3
63 -26.2 3150 1.2
tlk about 10 dB below the total noise level. An
80 -22.5 4000 1.0
estimate of the true source level can be obtained from 100 -19.1 5000 0.6
125 -16.1 6300 -0.1
160 –13.4 8000 -1.1
I 200 -10.9 10000 -2.5
250 -8.6 12500 -4.3
\ 315 -6.6 16000 -6.6
\ 400 -4.8 20000 9.3
\l 1

A-6 REVERBERATION TIME CALCULATION

An estimate of the reverberation time (T) of a room


I
can be obtained from the Sabine formula:

(0.16v)
T=
X4
where

v= is the volume of the room in cubic metres


(m)3. 7
A=
i
is the equivalent sound absorbing area in the
3 4 5 6 7 8 9 10 room in square metres (m2).
DIFFERENCE BETWEEN TOTAL AND EXTRANEOUS
The A. are the absorbing areas of each surface, or other
NOISE LEVEL (IN d13)
permkent fixture in the room. Each A. is determined
FIG. b SUBTRAC’I’1ON
OF NOISE LEVELS by multiplying the area of that sur;ace in square

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 29
. ----- --

O & 10 1’5 20 25 30 35 40 45 5’0 5’5 60

LOSSOFINSULATION: DEDUCT FROM


HIGHER INSULATION (IN dB)

FIG. 5 SOUNDINSULATION
OFNON-UNIFORM
PARTITIONS

metres (m2) by its absorption coefficient Usi. The individual Ai values. As the values of OCSi
are frequency
surface of each significant fixture or feature of the dependent, this calculation should be repeated for each
morn should be considered as well as the walls, ceiling octave band of interest.
and floor.
An allowance should also be made for people and
The Iotal absorption is obtained by summing the furnishings in the room.

30 NATIONAL BUILDING CODE OF INDIA


ANNEX B

(Clauses 2.24,2.38,2.41,2.50, 2.51,2.52 and 2.53)


SPECIFICATION OF SOUND INSULATION

B-1 GENERAL corrected level difference is known as the standardized


level difference, which has the symbol ~n~ and is
Sound insulating elements work mainly by reflecting
calculated using the following equation:
sound energy back into the source room, not by
absorbing it. The methods of measurement and the ~n~ = L~- L~ + 10 log10 (T/TO)
terms used are described in B-2 to B-4.
For laboratory ~measurements, the insulation of the
B-2 INSULATION AGAINST AIR-BORNE SOUND separating wall or floor being tested is required in a
way which is independent of the actual measuring
As per the standard tests, the insulation between a pair laboratory. For this reason, laboratories are designed
of rooms is measured either in third octave bands to have minimal flanking transmission and a different
having centre frequencies which cover at least the range correction is applied to account for the other factors.
100 Hz to 3150 Hz, or in octave bands which cover at This correction is 10 log ~0(MA).
least the range 125 to 2000 Hz. The noise is produced
by a loudspeaker in one of the rooms (called the source where
rrmm) and at each frequency the average noise levels S = is the common area of the separating wall
are measured in the source room (LJ and in the or floor in square metres (mz); and
adjacent receiving room (L~). The difference between
A = is the equivalent absorption area in the
these two levels (D) is a measure of the sound insulation
receiving room in square metres (m2).
between the rooms regardless of the transmission
path(s) the sound energy followed to travel between The laboratory corrected level difference at each
the rooms. The equation is as follows: frequency is known as the sound reduction index,
which has the symbol R and is calculated using the
D= Ls-L~
following equation:
The actual level in the receiving room depends on:
R = Ls - L,+ 10 log10 (WA)
a) the sound insulation of the separating wall or
If the test wall or floor is mounted in a realistic way in
floor,
the laboratory and flanking transmission will be low
b) the area of the separating wall or floor; in the field, the sound reduction index may be used to
c) the volume of the receiving room; predict its performance in the field. The relation
d) lhe amount of flanking transmission (that is between D,T and R is D~T = R -10 log10 (3S/V)
the importance of transmission paths other
where
than the separating wall or floor); and
e) the amount of absorbing material (for example S = is the area of the separating wall or floor in
furniture) in the receiving room. the field in square metres (mz); and
V = is the volume of the receiving room in the
For field measurements, apart from the amount of
field in cubic metres (m3).
absorption, these factors are a property of the building
and should be taken into account by the measurement This equation shows that if the source and receiving
procedure. As the amount of absorbing material (for rooms have different volumes, DnT will depend on
example soft furniture) in the room at the time of which is used as the source roam, using the larger room
measurement is arbitrary, it should be allowed for as the source room will give lower value.
separately. This is achieved by measuring the
reverberation time (T) of the room in seconds (s), B-3 INSULATION AGAINST IMPACT SOUND
which is a measure of how long it takes a sound to die The procedure to measure the impact insulation of
away after the source has been switched off, As the floors is rather different. Instead of a loudspeaker, a
sound energy is dissipated as heat in the absorbing machine containing five small hammers is placed on
material (T), it is related to the total amount of the floor. While the hammers strike the floor at a rate
absorption in the room. The receiving room level may of 10 blows a second, the resulting noise level (Li ) is
then be corrected to the level it would be if the room measured in the receiving room below at each of the
had a standard reverberation time (TO)whicli is typical same frequency bands used for airborne insulation. In
of furnished rooms, and is taken to be 0.5 s. The the field, the receiving room levels are again

PART 8 BUILDINGSERVICES— SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 31


‘corrected’ to a standard reverberation time (TO) of a floor with a carpet is likely to be overestimated by
!
0.5 s to give the standardized impact sound pressure this method.
level, L,~, which is calculated as follows:
The more common indices used to describe sound
Ln~ = Li – 10 log10 (Z’/TJ insulation are summarized in Table 11.

Table 11 Common Indices Used to Describe ?


In the laboratory, the noise level depends mainly on
the characteristics of the floor being tested and the Air-borne and Impact Sound Insulation
!
amount of absorption (A m2) in the laboratory. It is (Clause B-4)
therefore appropriate to correct the noise level to a
Air-borne Lab Measured Values Siagle Number -
standard area of absorption. The area used is 10 mz.
Quaatity i
The resulting normalized impact sound pressure ~!!ct ~:~d ~ ~ f
level is given the symbol L. and calculated as (0 (m Name Symbol Name symbol
I
follows: (1) (2) (3) (4) (5) (6)

l,. = J5i+ 10 log10 (A/10) A F Standardized Da, Weighted D.T,w


level standardized
difference level
B-4 RATING SOUND INSULATION difference
Measurements of insulation against both air-borne and A L Sound R Weighted R.
reduction sound I
impact sound yield values in a number of frequency index teduction
bands. To make this information more manageable, index
..
rating methods such as those in accordance with I F Standardized L’DT Weighted L’.T,~
[8-4(1)] are used to reduce the frequency band values impact sound standardized
pressurelevel impact sound
to single figure ratings. These single figure ratings pressurelevel
should be good predictors of subjective assessments I L Normrdized L’n Weighted L’., w
of insulation. However, this is not always the case and impact sound normalized
it is prudent to examine the full measurement data in pressurelevel impact sound
pressurelevel
critical situations. The impact insulation measured on

ANNEX C

(Clause 2.22)
NOISE RATING

C-1 Noise rating (NR) is a graphical method for where


assigning a single number rating to a noise spectrum.
L= is the octave band sound pressure
It can be used to specify the maximum acceptable level
level corresponding to NR level N;
in each octave band of a frequency spectrum, or to
and
assess the acceptability of a noise spectrum for a
particular application. The method was originally aandb = are constants for each frequency band,
proposed for use in assessing environmental noise, but as given in Table 13.
was later also fotind suitable for describing noise from NOTE — NR values can not be converted directly to
mechanical ventilation systems in buildings. To make dBA values but the following approximate relationship.
a rating, the noise spectrum is superposed on a family applies:
of NR contours; the NR of the spectrum corresponds
NR = dBA-6
to the value of the fust NR contour that is entirely above
the spectrum. The data for drawing NR contours (from C-3 Although the NR system is currently the preferred
NR O to NR 75) is given in Table 12 for the frequency method for rating noise from mechanical ventilation
range 31.5 Hz to 8 kHz. system, other methods which are more sensitive to *
noise at low frequencies are available, but they are not
C-2 For computational methods the curves are defined
yet widely accepted. Low frequency noise may be
by the equation:
disturbing or fatiguing to occupants, but may not have
L=a+bN much effect on the dBA or NR value.

32 NATIONAL BUILDING CODE OF INDIA


Table 12 Noise Rating Values Table 13 Values of a and b
(Clause C-1) (Clause C-2)
Noise Octave Band Centre Frequency, H,
Rating Sound Pressure Levels dB,, 20pPa Octave Band Centre a b
Frequency
/ \
31.5 63 125 250 500 1000 2000 4000 8000 Hz
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) (2) (3)

NR75 106 95 8’7 82 78 75 73 71 69 31.5 55.4 0.681


NR70 103 91 83 77 73 70 68 66 64 63 35.4 0.790
NR65 100 87 79 72 68 65 62 61 59
NR60 96 83 74 68 63 60 57 55 54 125 22.0 0.870
NR55 93 79 70 63 58 55 52 50 49 250 12.0 0.930
NR50 89 75 66 59 53 50 47 45 43 500 : 4.2 0.980
NR45 86 71 61 54 48 45 42 40 38
1000 0.0 1.000
NR40 83 67 57 49 44 40 37 35 33
NR35 79 63 52 45 39 35 32 30 28 2000 -3.5 1.015
NR30 76 59 48 40 34 30 27 25 23 4000 -6.1 1.025
NR25 72 55 44 35 29 25 22 20 18
8000 -8.0 1.030
NR20 69 51 39 31 24 20 17 14 13
NR15 664735261915129 7
NRIO 62433121151074 2
NR5 593926171052–1 -3
NRO 55352212504-6 -8

ANNEX D

(Clause 3.3)
OUTDOOR NOISE REGULATIONS IN INDIA

D-1 Government notifications are issued from time- around the residential areas and around sensitive
to-time on the allowable ambient noise levels in general buildings, specifically with regard to noise levels from
and specifically in different zones of various electricity generating sets, construction equipment and
metropolitan cities of India. HVAC utility equipment installed outdoors.

D-2 Noise regulations and notifications are also issued D-3 These regulations should be referred to by the
from time-to-time specifying the maximum permissible designer for the design of measures for control of
sound levels from equipments commonly used in and external noise.

ANNEX E

(Clauses 3,8 and 4.5)


SPECIAL PROBLEMS REQUIRING EXPERT ADVICE

E-1 GENERAL and similar performing spaces usually requires


expertise in room acoustics and noise control. The
Certain design problems require reliable advice of a
intrusion of quite low levels of noise may seriously
kind which is not easy to find in published material,
interfere with the enjoyment of the performance and
The advice of an expert should be sought for these
distract the performers. The requirements for low
kinds of problems, some examples of which are given
noise levels often mean that more room has to be
in E-2 to E-9.
allocated for low velocity ventilation ductwork and
E-2 ACOUSTIC TEST ROOMS the impact on the design of the ventilation system is
often substantial.
The design of rooms in which acoustic measurements
are carried out, such as reverberation chambers, free- E-4 BROADCASTING AND RECORDING
field anechoic rooms and audiometric test rooms, STUDIOS
#
usually requires the advice of an expert.
Broadcasting and recording studios have requirements
E-3 PERFORMING SPACES similar to those of performing spaces. For some
infrequent intrusive noises, the requirements are
The design of theatres, opera houses, concert halls sometimes relaxed on the grounds that a re-take of a

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION ANDNOISE CONTROL 33


P-

recording can be done, but this can result in higher E-9 NOISE SURVEYS
operating costs.
Noise surveys are carried out for a variety of reasons,
E-5 AIRCRAFT NOISE for example:

As there are many variables affecting the level of a) before construction, to establish the existing
aircraft noise heard on the ground, expert advice is noise climate at the site of a proposed
almost always required. Contours of daytime L~c~~ development where reliable prediction is
le-~els are available from most major airports. Where impracticable, as an aid to the design of the
measurements of fagade insulation are necessary a building envelope, either to protect against
standard test method may be referred. external noise or contain internally produced
noise;
E-6 GROUND-BORNE NOISE b) during construction, to monitor noise from
building activity, either to assess the likely
Projects involving ground-borne noise from underground
nuisance to the local community or the risk
trains usually require expert advice.
of hearing damage to the work force;
E-7 LOW-FREQUENCY NOISE c) at the end of a building contract to check the
insulation of the building envelope, or the
Projects involving low-frequency noise usually require
noise levels produced by the services;
expert advice as accurate measurement is difficult and
there is a shortage of reliable data below 100 Hz. d) as part of a planning requirement; and
e) to provide objective evidence to support or
E-8 ACTIVE NOISE CONTROL defend a legal action.
Active noise control is the reduction of noise by The expense of carrying out a comprehensive noise
cancellation with a similar noise (anti-noise) generated survey of any kind is likely to be high, so the cost-
by electro-acoustic means. The technique is still under effectiveness of a full or partial survey should be
development, but commercial systems are available weighed against alternatives such as prediction. A
which successfully reduce low frequency noise from survey will generally be more accurate and can take
mechanical ventilation systems. account of factors such as prevailing wind conditions.

ANNEX F

(Clause 4.4)

AIR-BORNE AND IMPACT SOUND INSULATION

F-1 GENERAL room 2 may travel via the direct path a-a and by the
many indirect, or flanking, paths shown. The term
Air-borne sound refers to sources which produce sound
flanking transmission is usually used to mean
by directly setting the air around them into vibration.
transmission paths involving the structure, while the
Impact sound refers to sources which produce sound
term indirect transmission includes flanking paths and
by impulsive mechanical excitation of part of a building
airborne paths through gaps and ducts, etc. The indirect
(for example by footsteps, electric light switches,
paths may limit the sound insulation attainable no
slamming doors). Many sources of impact sound also
matter how much the dirpct sound is reduced by the
produce significant levels of airborne sound. The term
separating wall or floor. The indirect transmission can
structure-borne sound has no very precise meaning as
be reduced by measures such as the following:
the structure can be excited by both airborne and impact
sources; it is often used to refer to sound that travels a) Increasing the mass of the flanking walls;
for long distances via the structure, especially in b) Increasing the mass of the partition and
connection with vibrating machinery linked directly bonding it to the flanking walls;
to the structure. c) Introducing discontinuities in the indirect
paths;
F-2 DIRECT AND INDIRECT TRANSMISSION
d) Erecting independent wall linings adjacent to
Figure 6 shows diagrammaticrdly a pair of rooms in a the flanking walls to prevent energy entering
house where the construction consists of solid walls, the flanking construction; and
etc bonded together. Sound traveling from room 1 to e) Sealing any air gaps and paths through ducts.

34 NATIONALBUILDING CODE OF INDIA


R

ELEVATION

ROOM

PLAN

FIG. 6 TRANSMISSION
PATHS(VIA THESTRUCTURE)OF NOISE ORIGINATING
IN ROOM 1 (DIAGRAMMATIC)

Figure 7 shows a number of indirect paths that have measurements to those likely to be obtained in the
been found in offices. field.
It is important to remember that standard test F-3 AIR-BORNE SOUND INSULATION
laboratories are designed to minimize transmission
bv. all paths other than the direct path. This makes F-3.1 General
it difficult to relate the results of laboratory The sound insulation of structural elements such as

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 35
n

11

111X

/ 0 & 6

/
~ 7/ 11

I
-

1 LIGHTWEIGHT PANELS ABOk DOORS 7 ELECTRICAL OUTLETS AND SERVICE PIPES


2 DOORS 8 LIGHTWEIGHT MULLIONS OR MULLION/PARTITION CLOSERS
3 AIR LEAKS THROUGH GAPS, CRACKS OR HOLES 9 CONTINUOUS SILL LINE HEATING
4 ——— --— TRANSMISSION WA SUSPENDED CEILINGSIPARTITIONS
SOUND 10 PARTITION PERFORMANCE
5 COMMON VENTILATlON SYSTEh4S VVITHOUT skENc~Rs 11 APPLIANCES
6 COMMON FLOOR DUCT 12 CONTINUOUS LIGHTING FITTINGS

FIG. 7 INDIRECTSOUND LEAKAGE PATHS

,.
walls and floors always varies with frequency, the Table 14 Sound Insulation of Imperforate
insulation rising in general as the frequency rises. Sheet Materials
(Clause F-3.3)
F-3.2 Terminology
Material Surface Typical Weighted
Results from field measurements are usually Mass Sound Reduction
expressed in terms of the weighted standardized level Index, R.
difference, while laboratory measurements are usually kg/m2 dB
expressed in terms of the sound reduction index. In (1) (2) (3)
the absence of significant flanking transmission, 3 mm glass sheet 7.0 26
the numerical difference between the weighted 12.5 mm plasterboard 10.5 31
standardized level difference and the sound reduction 18 mm wood particle board 8.0 27
19 mm plywood - 3.0 24
index of a wall or floor is usually small for furnished 16 mm p]ywood 4.5 24
rooms in dwellings, and so either quantity may be 1 mm steel sheet 11.0 29
used in considering principles; for this purpose it is, 6 mm hardboard 5.0 25
12 mm wood fibre insulation 4.0 24
therefore, convenient to use the general term board
insulation. 13 mm mineral fibre board 4.0 24
50 mm wood-wool SCretXk?d 35.0 33
F~3.3 Mass Law one side

An approximate empirical relationship has been


F-3.4 The Coincidence Effect
established between sound insulation and mass for
single leaf constructions as shown in Fig. 8. This so The coincidence effect occurs when the wavelength
called ‘mass law’ gives a useful first approximation to of the wave impressed on the panel by the incident
the behaviour of a single sheet or plate. In practice, sound wave is close to the wavelength of free bending
the sound insulation predicted by the mass law may waves in the panel. The effect of coincidence is to
not be attained because of factors such as the lower the sound insulation of a construction by as
coincidence effect, which is outlined in F-3.4. Results much as 10 dB below the level expected from its mass
for specific materials vary around the value given by per unit area over a limited frequency range. The
the mass law relationship, and so measured data should coincidence effect can be pronounced with thin
be used when available. Table 14 gives a lists of lightweight partitions, resulting in loss of insulation
materials and indicates the sound insulation of a single, at middle and high frequencies. Reducting the
imperforate sheet when fixed to a suitable wood or stiffness without a corresponding reduction of mass
metal framework. These values are useful, for example can raise the critical frequency above 3 150 Hz, and
when assessing existing structures. so improve the insulation over the important 100 Hz

55

50
RN= 21.65 Ig m’ -2.3
m’ h. 50 kglm 2
45 1

40 -

35
.

30
10 100 1000

SURFACE MASS, m’ (kgIn? ) .

FIG. 8 MASS LAW CURVE

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 37
to 3 150 Hz range. An increase of stiffness will have sound from footsteps. However, it should be noted that
the reverse effect. an effective floating floor may result in increased sound
from impacts on the source side of the floor.
It is possible to design lightweight stud partitions so
The conventional forms of floating floor may be
that they perform to their maximum effect in the speech
unsatisfactory if protection against the low-frequency
frequency region between 250 Hz and 2000 Hz, that
content of impact noise is required (e.g. a dance floor
is between the mass-spring-mass and coincidence
over a restaurant).
regions respectively.
F-4 AIR-BORNE INSULATION VALUES OF
The worst coincidence dips occur in materials such as
WALLS AND AIR-BORNE AND IMPACT
plate glass and rigid metal sheets. Heavily damped
INSULATION VALUES OF FLOORS
materials such as lead sheets are least affected.
Table 15 and Table 16 give examples of common types
F-3.5 Mass-Spring-Mass Frequency of w all and floor construction with sound insulation in
A double leaf wall can perform better than a single the ranges shown. The insulation indices are for field
leaf wall of similar mass because the souncl has to pass measurements accessed in accordance with [8-4(5)].
through two barriers. If the two leaves are not The insulation values given are necessarily approximate
connected to each other, the insulation values of the since examples of nominally identical constructions
two leaves may be added together. However, in practice may show variations of several decibels. All the figures
the leaves are often connected by ties or studs, and the represent values expected in the field, that is in
full insulation cannot be achieved. Even where the two actual buildings. Many are based directly on field
leaves are isolated from each other, the full benefit measurements, though other (in the absence of
can only be obtained above a certain frequency that representative field measurements) have been assessed
depends on the cavity width. This is because the air in from laboratory data, with an allowance for typical
the cavity behaves like a spring connecting the leaves flanking conditions in normal buildings. Variation in
the amount of indirect transmission may affect
together, and causes a resonance at the mass-spring-
mass frequent y. Below this frequency, the two leaves significantly the insulation between two rooms
separated by a given barrier. For example, the sound
behave more like an equivalent single leaf.
insulation of some types of floor may be reduced by
Making the cavity width wide can reduce the mass- indirect transmission along the walls supporting them,
spring-mass frequency, as in the case of sound insulating particularly if these walls are of lightweight masonry
secondary glazing. The mass-spring-mass frequency and carried past the floor.
(F’O)maybe estimated from the following equation:
Table 15 Air-borne Sound Insulation of
Walls and Partitions
(Clause F-4)
Jqn$ %)
where Sound Type of Wall or Partition
Insulation
ml and m2 = the surface masses of the two leaves D TIT, W

dB
in kilograms per square metre
(1) (2)
(kg/m2); and
d= the cavity width in metres (m). 26 to 33 a) 1 mm steel sheet panels fixed to steel frame
members to form remountable partition units
F-3.6 Impact Sound Control 50 mm overall thickness. Mineral wool cavity
insulation.
A structure that receives an impact or has a vibrating b) Plywood or wood fibre board 12 mm thick nailed
source in contact with it behaves more like an extension both sides of 50 mm x 50 mm timber framing
of the source rather than an intervening element members spaced at 400 mm centres.
between source and listener. For this reason, a relatively c) Paper faced strawboard or wood wool 50 mm thick
small amount of impact energy may produce a loud panels plastered both sides.

sound and, if the structure is continuous, the sound d) Chipboard hollow panels 50 mm thick tongued . b’:
and grooved edges, hardboard faced. Joints
may travel a long distance. Control is usually obtained covered with wood trim.
by inserting a resilient surface at the point of contact 33 to 37 a) Lightweight masonry blockwork. Plaster or
with the source (for example laying a carpet on a floor) drylining on at least one side. Overall mass per
or by introducing a structural discontinuity. unit area not less than 50 kg/m2.
b) Laminated plasterboard at least 50’mm thick fixed
Floating floors, which are an example of the latter to timber perimeter framing, any suitable finish.
approach, are a common method of controlling impact Approximate mass per unit area 35 kg/m2.

38 NATIONAL BUILDING CODE OF INDIA


Table 15 — Continued Table 15 — Concluded

(1) (2) (1) (2)

c) Timber stud partitions any size timbers greater than e) Cavity lightweight aggregate block (maximum
50 mm x 50 mm, 400 mm centers, cross noggins, density of block 1600 kg/m3) with 75 mm cavity
9.5mm plasterboard lining on both sides, any and wall ties of the butterfly wire type. Dry
suitablefinish. lined finish on both sides. Joints in blockwork
Metalstudpartition,50 mmstuds600 mmcentres, well filled. Overall mass per unit area not less than
clad both sides with 12.5mmplasterboard,joints 300 kg/m2.1}
filled and perimeters sealed. Approximatemass f) Dense aggregate concrete block cavity wall with
per unit area 18 kg/m2, 50 mm cavity and wall ties of the butterfly wire
type. Dry lined finish on both sides. Joints in block
e) 50 mm lightweightmasonryblockwork,plastered
both sides to 12mm thickness or drylined with work well filled. Overall mass per unit area not
9.5 mm plasterboard. less than 415 kg/m2.1,
37t043 a) Lightweight masonry clockwork, plaster or dry .@ Autoclave aerated concrete block cavity wall
lining on at least one side. Overall mass per unit consisting of two leaves, 100 mm blocks not less
area not less than 75 kg/ml. than 75 mm apart, with wall ties of the butterfly
type. Plaster or dry line finish on both sides. Joints
b) Either 75mm or 100mm x 50mm timber studs in blockwork well tilled. Overall mass per unit
spaced 600mm apart, 50mm mineral fibre quilt area not less than 150 kg/m2.’)
in stud cavity. Frame lined on both sides with one
layer 12.5mm plasterboard, Approximate mass 54 to 60 a) Two separate frames of timber studs not less than
per unit area 19kg/m2. 100 mm x 50 mm spaced at 600 mm maximum
centres, A 50 mm mineral wool quilt in each frame
43t050 a) Masonry wall, joints well filled. Either plaster or
between studs. Frames spaced to give a minimum
dry lining on both sides. Overall mass per unit 300 mm overall cavity. Each frame clad on outside
arednot less than 150kg/m2.
with three layers of 12.5 mm plasterboard
b) 100 mm metal stud partition, ‘C’ section studs not nailed to framing. Approximate mass per unit area
greater than 600mm spacing, not less than 51 kg/m2.1)
nominal 50mm web depth. Clad on both sides
b) Two separate frames of boxed ‘C’ section
with two layers of plasterboard of not less than galvanized nominal 150 mm steel studs 100 mm
22mm combined thickness. Mineral fibre quilt apart with a 400 mm overall cavity. 50 mm
hung between studs. Approximate mass per unit mineral wool quilt fixed to the back of one frame
area35 kg/m2. each frame clad on outside with three layers
c) 75 mm x 50 mm timber framing using staged studs of 12.5 mm plasterboard by self drilling or
at 300mrn spacing with 25mm stagger forward tapping screws. Approximate mass per unit area
and back. Frame clad with two layers of 12.5 mm 47 kg/m2.1)
ofplasterboard on both sides. Mineral fibre quilt
hung between studs. Approximate mass per unit c) Solid masonry with an overall mass per unit
area of not less than 700 kg/m2 fully sealed both
area 36 kg/m*.
sides. 1)
d) 50mm x 25mmtimber sttsd partition to form a
d) Dense aggregate concrete block solid wall
25 mm cavity, clad on both sides with minimum
215 mm thick plaster finish to both surfaces.
38 mm wood wool slabs having their outer faces
Overall mass per unit ma not less than 415 kg/m2.])
screeded or plastered.
e) Cavity lightweight aggregate block (maximum
e) Solid autoclave aerated concrete block 215 mm density of block 1600 kg/m3) with 75 mm cavity
thick plaster or dry lined finish on both sides, and wall ties of the butterfly wire type. Plaster
blockworkjoints well filled. Overall mass per unit
finish on both sides, Joints in blockwork well
area not less than 160kg/m2. filled. Overall mass per unit area not less than
50t054 a) Two separate frames of timber studs not less than 300 kg/m2.1)
89 mm x 38 mm, or boxed metal studwork with
f) Dense aggregate concrete block cavity wall with
50 mm minimum web depth. Studs at 600 mm 50 mm cavity and wall ties of the butterfly wire
maximum centres. A 25 mm mineral wool quilt
type. Plaster finish on both sides, Joints in
suspended between frames. Frames spaced to give
blockwork well filled. Overall mass per unit area
a minimum 200 mm overall cavity. Clad on
not less than 4d5
., kg/m2.1)
outside of each frame with a minimum of 30 mm
plasterboard layers (for example 19 mm plus NOTES
12.5 thickness). Approximate mass per unit area 1 Construction details and workmanship are
54 kg/m2.1j important if the levels of sound insulation
b) Either in-situ or pre-cast concrete wall panel indicated are to be achieved.
not less than 175 mm thick and not less than 2 Where plasterboard is specified it is assumed
415 kg/m2. All joints well filled.lj that the surface mass will beat least 6.5 kg/m2 for
c) Brick wall nominal 230 mm thickness, weight 9.5 mm thick board, at least 8.5 kg/mz for 12.5 mm
(including plaster) not less than 380 kg/m2.Plaster thick board, and at least 14.5 kg/m2 for 19 mm
or @-lined finish both sides. Brick work joints thick board. If less dense plasterboard is used, the
well filled. 1, thickness should he increased.
d) ‘No fines’ concrete 225 mm thickness, weight I) When considering these constructions for SepZMhg walk,
(includingplaster)not lessthan415 kg/m2.Plaster expert advice should be sought.
or drylined finish both sides. 1,

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 39
Table 16 Air-borne and Impact Sound Table 16 — Concluded
Insulation of Floor Constructions
(1) (2)
(Clause F-4)
the floor, ceiling and pugging is not tess than
Sound Type of Wall or Partition 120 kg/m2. This construction will only give
Insulation values for DnT,~ of 50 to 53 dB, and a value
dB for L;=, ~of 75 dB.
(1) (2)
d) A floor consisting of 18 mm tongued and
grooved chipboard on 19 mm plasterboard
D“T,~ =49 to 54 a) A concrete floor having mass per unit area
laid on battens running parallel to the
L;,, ~= 56 to 65 not less than 365 kglm2,including any screed
joists and supported on 25 mm thick
or ceiling finish directfy bonded to the floor
mineral wool of about 90 kg/m3 to 140 kg/
slab; together with a floating floor or resilient
m3 density; 100 mm of fibre absorbent
floor coveting equivalent to robber or sponge
(as used for insulation iu roof spaces)
rubber underlay or thick cork tile (for
laid between the joists on top of the
example carpet and underlay or sponge
plasterboard ceiling.])
rubber backed vinyl flooring),
A floor consisting of 18 mm tongued and
b) A solid floor consisting of
grooved chipboard on 19 mm plasterboard
1) a solid slab; or floating on a 25 mm thick mitterat wool layer
2) concrete beams and infilling blocks; or of about 60 kg/m3 to 80 kg/m3 density; this
on a 12.5 mm plywood platfom, 100 mm
3) hollow concrete planks; together with a
floating floor. A ceiling finish is required of fibre absorbent laid between the joists on
for a beam and block floor. In each case top of the plasterboard ceiling.l)
the slab should have a mass per unit area D“T,~ =32 to 36 Timber joist floor consisting of 22 mm
of at least 300 kg/m2including any screed L;T, ~ = 80 to 85 tongued and grooved floor boarding or
or ceiling finish directly bonded to it. equivalent t3xed directly to floor joists.
Where a floating floor is laid over a floor of Ceiling of 12.5 mm plaatarboard and skim
beams and hollow infill blocks or hollow with no fleer covering.
beams along the top of the structural floor, it
should be sealed and levelled before the NOTES
resilient layer is put down. It is also essential 1 Construction details and workmanship are important if the
to have due regard for conduits and pipework levels of sound insulation indicated are to be achieved.
which should be laid and covered so as to
2 Where plasterboard is specified it is assumed that the surface
prevent any short circuit of the floor’s
mass will be at least 8.5 kg/m3 for 12.5 mm thick board, and at
isolating properties.
least 14.5 kg/m2 for 19 mm thick board. If less dense
If precast units are used as a structural floor, plasterboard is used, the thickness should be increased.
it is essential that thejoints are tilled to ensure
that the sound insulation performance is
maintained. 1JIn these types of floor construction, the ceifing maYbe 19 m
The resilient material is laid to cover plus 12.5 mm plasterboard. It is imperative that the resilient
completely the structural floor and turned up layer is not punctured by nails.
against the surrounding watl along rdledges.
The resilient layer is usuafly of mineral fibre,
or a speciaf grade of expanded polystyrene. In many cases, simple solid partitions give insulation
When the screed is laid, it is important that values according to their mass (see F-3.3). Moreover,
none of the mix finds its way through the with partitions of this type there is usually little
resilient layer to the structural floor, as this
will short circuit the isolation between the two variation between field and laboratory test results
decks and significantly reduce the sound unless he laboratory insulation exceeds 45 dB.
insulation. Exceptions may occtw in buildings that have not been
A floor consisting of boarding nailed to specially designed to minimize common cavities and
battens laid to float upon an isolating layer
strongly coupled element$ in lightweight panelling.
of mineral fibre capable of retaining its
resilience under imposed loading. With The examples given are not exhaustive. Flanking
battens mtming rdongtie joista, a dense fibre structures are not listed since these can vary widely
layer can be used in strips. The ceiling below and are often dependent upon other factors such as
to be of metal lath and plaster not less than
thermal insulation, which are outside the scope of this
29 mm thick, with pugging on the ceiling
such that the combined mass per unit area of Code.

40 NATIONAL BUILDING CODE OF INDIA


ANNEX G

(Clause 13.1)
BASIC DESIGN TECHNIQUES FOR NOISE CONTROL IN AIR CONDITIONING,
HEATING AND MECHANICAL VENTILATION SYSTEM

G-1 When selecting fans and other related mechanical separation, resulting from expansion angles
equipment and when designing air distribution systems greater than 15°, may produce rumble noise.
to minimize the sound transmitted from different Expanding the duct cross-section area will
components to the occupied spaces that they serve, the reduce potential flow noise associated with
following recommendations should be considered: turbulence in these areas.

a) Design the air distribution system to minimize h) Use turning vanes in large 90° rectangular
flow resistance and turbulence. High flow elbows and branch takeoffs. This provides a
resistance increases the required fan pressure, smoother transmission in which the air
which results in higher noise being generated can change flow direction, thus reducing
by the fan. Turbulence increases the flow turbulence.
noise generated by duct fittings and dampers j) Place grilles, diffusers and registers into
in the air distribution system, especially at low occupied spaces as far as possible from
frequencies. elbows and branch takeoffs.
b) Select a fan to operate as near as possible to k) Minimize the use of volume dampers near
its rated peak efficiency when handling the grills, diffusers and registers in acoustically
required quantity of air and static pressure. critical situations.
Also, select a fan that generates the lowest m) Vibration isolate all vibrating reciprocating
possible noise but still meets the required and rotating equipment if mechanical
design conditions for which it is selected. equipment is Iocated on upper floors or is
Using an oversized or undersized fan that roof-mounted. Also, it is usually necessary
does not operate at or near rated peak to vibration isolate the mechanical equipment
efficiency may result in substantially higher that is located in the basement of a building
noise levels. as well as piping supported from the ceiling
c) Design duct connections at both the fan inlet slab of a basement, directly below tenant
and outlet for uniform and straight air flow. space. It may be necessary to use flexible
Failure to do this may result in severe piping connectors and flexible electrical
turbulence at the fan inlet and outlet and in conduit between rotating or reciprocating
flow separation at the fan blades. Both of equipment and pipes and ducts that are
these may significantly increase the noise connected to the equipment.
generated by the fan. n) Vibration isolate ducts and pipes, using
d) Select duct silencers that do not significantly spring and/or neoprene hangers for at least
increase the required fan total static pressure. the first 15 m from the vibration-isolated
e) Place fan-powered mixing boxes associated equipment.
with variable volume air distribution systems P) Use barriers near outdoor equipment when
away from noise-sensitive areas. noise associated with the equipment will
f) Minimize flow-generated noise by elbows or disturb adjacent properties if barriers are not
duct branch take-offs, whenever possible, by used. In normal practice, barriers typically
locating them at least four to five duct produce no more than 15 dB of sound
diameters from each other. For high velocity attenuation in the mid-frequency range.
systems, it may be necessary to increase this q) Table 17 lists several common sound sources
distance to up to ten duct diameters in critical associated with mechanical equipment noise.
noise areas. Anticipated sound transmission paths and
g) Keep airflow velocity in the duct as low as recommended noise reduction methods are
possible (7.5 nds or less) near critical noise also listed in Table 18. Air-borne and/or
areas by expanding the duct cross-section structure-borne sound can follow any or all
area. However, do not exceed an included of the transmission paths associated with a
expansion angle of greater than 15°. Flow specified sound source.

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 41
,

Table 17 Sound Sources, Transmission Paths and Recommended


Noise Reduction Methods
[Clause G-l(q)]

Sound Source Path No.


(see Table 18)
Circulating fans, grilles, registers, diffusers, unitary equipment in room 1
Induction coil and fan-powered VAV mixing units 1,2
Unitary equipment located outside of room served; remotely located air-handling equipment, such as fans, blowers, 2.3
dampers, duct fitting, and air washers
Compressors, pumps, and other reciprocating and rotating equipment (excluding air-handling equipment) 4,5,6
Cooling towers; air-cooled condensers 4,5,6,7
Exhaust fans; window air conditioners 7,8
Sound transmission between rooms 9,10

Table 18 Sound Transmission Paths and Recommended .


Noise Reduction Methods
[Clause G-l(q) and Table 17]

Path Transmission Paths Noise Reduction Methods


No.
(1)

1 Direct sound radiated from sound sources to ear. Direct sound can be controlled only by selecting quiet equipment.
Reflected sound from walls, ceiling and floor. Reflected sound is controlled by adding sound absorption to the
room and to equipment location.
2 Air and structure-borne sound radiated from casings and Design duct and fittings for low turbulence; locate high velocity
through walls of ducts and plenums is transmitted through ducts in non-critical areas; isolate ducts and sound plenums from
walls and ceiling into rooms. structure with neoprene or spring hangers
3 Airborne sound radiated through supply and return air Select fans for minimum sound power; use ducts lined with sound-
ducts to diffusers in room and then to listener by Path 1. absorbing material; use duct silencers or sound plenums in supply
and return air ducts.
4 Noise transmitted through equipment room walls and Locate equipment rooms away from critical areas; use masonry
floors to adjacent rooms. blocks or concrete for equipment room walls and floor.
5 Vibration transmitted via building structure to adjacent Mount all machines on properly designed vibration isolators; design
walls and ceilings, from which it radiates as noise into mechanical equipment room for dynamic loads; balance rotating
room by Path 1. and reciprocating equipment.
6 Vibration transmission along pipes and duct walls. Isolate pipe and ducts from structure with neoprene or spring
hangers; install flexible connectors between pipes, ducts, and
vibrating machines.
7 Noise radiated to outside enters room windows. Locate equipment away from critical areas; use barriers and covers
to interrupt noise paths; select quiet equipment.
8 Inside noise follows Path 1. Select quiet equipment.
9 Noise transmitted to an air diffusers in a room, into a duct, Design and install duct attenuation to match transmission loss of
and out through an air diffuser in another room. wall between rooms.
10 Sound transmission through, over, and around room Extend partition to ceiling slab and tightly seal all around; seal all
partition. pipe, conduit, duct and other partition penetrations.

ANNEX H
(Clause 13.2)
SUGGESTED EQUIPMENT NOISE DATA SHEET

It is recommended that an equipment noise data sheet units specifying noise requirements at the time of
be furnished to intending bidders of mechanical request for quotation. Following is a sample noise data
equipment such as air conditioning, heating and sheet suggested for the purpose:
mechanical ventilation machinery or diesel generating

42 NATIONAL BUILDING CODE OF INDIA


.T

Sample of Equipment Noise Data Sheet for Noise Specification


to be Sent to Suppliers

Equipment Description Type Item No.

Octave-Band Desired Sound Supplier to Complete


Centre Frequency, Pressure Level, / & h
Hz LP Actual Special Design Special Noise Control
Measures Recommended
(1) (2) (3) (4) (5)

63
125
250
500
1000
2000
4000
8000

NOTES
1 The measurements of SPL shall be at a distance of 1.0 m from the equipment and 1.5 m above grade or floor. The measurement
methud shall be described and the point of maximum levels famished.
2 Complete CO13 for actual levels of standard equipment.
3 Cumplete COI4 for special design for low noise (if such alternative is available).
4 Complete CO15for noise control measures such as enclosure.
5 Indicate if the equipment meets the specified noise levels without modification (Yes/No).
6 If no, additional costs required:

For CO14
For CO15

It will be observed from the COI 3, 4 and 5 that the would indicate the acoustical performance if the
buyer would get quotation for supply of a standard owners were to provide special noise control measures
equipment at a price P-1, whose noise characteristics for the installation (whose broad details and
would be as per CO13. Col 4 would indicate acoustical approximate estimated cost is also furnished by the
performance for a special design at a price P-2, Col 5 vendor).

LIST OF STANDARDS

The following list records those standards which are IS No. Title
acceptable as ‘good practice’ and ‘accepted standards’
(2) 4954:1968 Recommendations for noise
in the fulfillment of the requirements of the Code. The
abatement in town planning
latest version of a standard shall be adopted at the time
of enforcement of the Code. The standards listed may (3) 2526:1963 Code of practice for acoustical
be used by the Authority as a guide in conformance design of auditoriums and
with the requirements of the referred clauses in the conference halls
Code. (4) 11050 Rating of sound insulation in
buildings and of building
IS No. Title
elements:
(1) 11050 Rating of sound insulation in
(Part 1) :1984 buildings and of building (Parf 1) :1984 Air-borne sound insulation in
elements: Part 1 Air-borne buildings and of interior
sound insulation in buildings building elements
and of interior building elements (Parf 2) :1984 Impact sound insulation

PART 8 BUILDING SERVICES — SECTION 4 ACOUSTICS, SOUND INSULATION AND NOISE CONTROL 43
-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES

Section 5 Installation of Lifts and Escalators

BUREAU OF INDIAN STANDARDS


CONTENTS

FOREWORD ... 3

1 SCOPE . .. 5
2 TERMINOLOGY ... 5
3 GENERAL ... 9
4 ESSENTIAL REQUIREMENTS ... 11
5 DIMENSIONAL TOLERANCES ... 21
6 PRELIMINARY DESIGN ... 22
7 POWER AND CONTROL SYSTEMS ... 28
&
8 CONDITIONS FOR OPTIMUM PRACTICE ... 33
9 RUNNING AND MAINTENANCE ... 35
10 LIFT ENQUIRY OR INVITATION TO TENDER ... 35
11 ACCEPTANCE OF TENDER AND SUBSEQUENT PROCEDURE ... 37
12 CO-ORDINATION OF SITE WORK ... 38
13 PROCEDURE FOLLOWING TEST, INCLUDING INSPECTION AND ,,. 39
MAINTENANCE
14 ESCALATORS . .. 40

LIST OF STANDARDS ... 42

NATIONAL BUILDING CODE OF INDIA


F-

National Building Code Sectional Committee, CED 46

FOREWORD

This Section was first published in 1970 and was subsequently revised in 1983, This Section covers the essential
requirements for installation of lifts and escalators in buildings, This Section shall, however, be read with
Part 4 ‘Fire and Life Safety’ from fue safety requirements point of view. The major changes in the last revision
were addition of outline dimensions of different types of lifts and detailed requirements of escalators in buildings.
Emphasis was laid on coordination between the engineer/architect and the lift manufacturer to arrive at the
number and position of lifts for attaining optimum efficiency in serving the building with safety.

As a result of experience gained in implementation of 1983 version of the Code and feedback data received as
well as revision of Indian Standards on which this Section was based, a need was felt to revise this Section. This
revision has, therefore, been prepared to take care of these. The significant changes incorporated in this revision
includes:

a) New clausesh-ecommendations have been added on Building Management System.


b) New clauses have been added on fireman’s lift, infra-red light curtain safety and Braille button for blind
people.
c) The provisions have been updated as per the revised standards on lifts on which this Section is based.
d) The list of Indian Standards as good practices/accepted standards has been updated.

The information contained in this Section is largely based on the following Indian Standards:

IS No. Title
962:1989 Code of practice for architectural and building drawings (second revision)
4591 ; 1968 Code of practice for installation and maintenance of escalators
14665 Specification for electric traction lifts:
(Part 1) : 2000 Guidelines for outline dimensions of passenger, goods, service and hospital
lifts
(Part 2/See 1 &2): 2000 Code of practice for installation, operation and maintenance, Section 1
Passenger and goods lifts, Section 2 Service lifts
(Part 3/See 1 &2): 2000 Safety rules, Section 1 Passenger and goods lifts, Section 2 Service lifts
(Part 4/See 1 to 9) :2001 Components, Section 1 Lift buffers, Section 2 Lift guide rails and guide shoes,
Section 3 Lift carframe, car, counterweight and suspension, Section 4 Lift
safety gears and governors, Section 5 Lift retiring cam, Section 6 Lift doors
and locking devices and contacts, Section 7 Lift machines and brakes,
Section 8 Lift wire ropes, Section 9 Controller and operating devices
(Part 5) : 1999 Inspection manual

All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to
revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying
the most recent editions of the standards.

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 3


-,
(J 6$
NATIONAL BUILDING CODE OF INDIA
PART 8 BUILDING SERVICES

Section 5 Installation of Lifts and Escalators

1 SCOPE which absorbs and dissipates the kinetic energy of the


descending car or counterweight.
1.1 This Section covers the essential requirements for
the installation, operation and maintenance and also 2.5.1.1 Oil buffer stroke — The oil displacing
inspection of lifts (passenger lifts, goods lifts, hospital movement of the buffer plunger or piston, excluding
lifts, service lifts and dumb waiter) and escalators so the travel of the buffer plunger accelerating device.
as to ensure safe and satisfactory performance.
2.5.2 Spring Bu#er — A buffer which stores in a spring
1.2 This Section gives information that should be the kinetic energy of the descending car or
exchanged among the architect, the consulting engineer counterweight.
and the liftiescalator manufacturer from the stage of
2.5.2.1 Spring buffer load rating — The load required
planning to installation including maintenance.
to compress the spring by an amount equal to its stroke.
NOTE — The provisions given in this Section are primarily
for electric traction lif~ however,most of these provisionsare 2.5.2.2 Spring buffer stroke — The distance, the
also applicable to hydraulic lifts {see good practice [8-5(1)]. contact end of the spring can move under a compressive
load until the spring is compressed solid.
2 TERMINOLOGY
2.6 Call Indicator — A visual and audible device in
2.0 For the purpose of this Section, the following the car to indicate to the attendant the lift landings from
definitions shall apply.
which calls have been made.
2.1 Automatic Rescue Device — A device meant to
2.7 Car Bodywork — The enclosing bodywork of
bring a lift stuck between floors due to loss of power, the lift car which comprises the sides and roof and is
to the nearest level and open the doors in order to allow built upon the car platform.
trapped passengers to be evacuated. Such a device may
use some form of internal auxiliary power source 2.8 Car Door Electric Contact — An electric device,
for such purpose, complying with all the safety the function of which is to prevent operation of the
requirements of a lift during normal run. The speed of driving machine by the normal operating device unless
travel is usually lower than the normal speed. In the the car door is in the closed position.
case of manual doors on reaching the level, the device
2.9 Car Frame — The supporting frame or sling to
shall allow the door to be opened and in case of power which the platform of the lift car, its safety gear, guide
operated doors the device shall automatically open the shoes and suspension ropes are attached.
door.
2.10 Car Platform — The part of the lift car which
2.2 Baluster — A short pillar slender above and
forms the floor and directly supports the load.
bulging below.
2.11 Clearance
2.2.1 Balustrade — A row of balusters meant for
supporting moving handrails. 2.11.1 Bottom Car Clearance — The clear vertical
distance from the pit floor to the lowest structural or
2.3 Bottom Car Runby — The distance between the
mechanical part, equipment or device installed beneath
car buffer striker plate and the striking surface of the
the car platform aprons or guards located within
car buffer when the car is in level with the bottom
300 mm, measured horizontally from the sides of the
terminal landing.
car platform when the car rests on its fully compressed
I 2.4 Bottom Coutnerweight Runby — The distance buffers.
between the counter weight buffer striker plate and
2.11.2 Top Car Clearance — The shortest vertical
the striking surface of the counterweight buffer when
distance between the top of the car crosshead, or
the car is in level with the top terminal landing.
between the top of the car where no crosshead is
2.5 Buffer — A device designed to stop a descending provided, and the nearest part of the overhead structure
car or counter weight beyond its normal limit of travel or any other obstruction when the car floor is level
by storing or by absorbing and dissipating the kinetic with the top terminal landing.
energy of the car or counterweight.
2.11.3 Top Counterweight Clearance — The shortest
2.5.1 Oil Bu.er — A buffer using oil as a medium vertical distance between any part of the counterweight

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 5


structure and the nearest part of the overhead structure slides horizontally and consists of two or more panels
or any other obstruction when the car floor is level which open from the centre and are usually so
with the bottom terminal landing. interconnected that they move simultaneously.

2.12 Control — The system governing starting, 2.15.2 Door, Mid-Bar Collapsible — A collapsible
stopping, direction of motion, acceleration, speed and door with vertical bars mounted between the normal
retardation of moving member. vertical members.

2.12.1 Single-Speed Alternating Current Control — 2.15.3 Door, Multipanel — A door arrangement
A control for a driving machine induction motor which whereby more than one panel is used such that the
is arranged to run at a single-speed. panels are connected together and can slide over one
another by which means the clear ‘opening can be
2.12.2 Two-Speed Alternating Current Control — A
maximized for a given shaft width. Multipanels are
control for a two-speed driving machine induction
used in centre opening and two speed sliding doors.
motor which is arranged to run at two different
synchronous speeds either by pole changing of a single 2.15.4 Door, Single Slide — A single panel door
motor or by two different armatures. which slides horizontally.

2.12.3 Rheostatic Control — A system of control 2.15.5 Door, Two Speed Sliding — A door which
which is accomplished by varying resistance or slides horizontally and consists of two or more panels,
reactance or both in the armature or field circuit or one of which moves at twice the speed of the other.
both of the driving machine motor.
2.15.6 Door, Vertical Bi-parting — A door which
2.12.4 Variable Voltage Motor Control (Generator slides vertically and consists of two panels or sets of
Field Control) — A system of control which is panels that move away from each other to epen and
accomplished by the use of an individual generator are so interconnected that they move simultaneously.
for each lift wherein the voltage applied to the driving
2.15.7 Door, Vertical Lifiing — A single panel door,
machine motor is adjusted by varying the strength and
which slides in the same plane vertically up to open.
direction of the generator field.
2.15.8 Door, Swing — A swinging type single panel
2.12.5 Electronic Devices — A system of control
door which is opened manually and closed by means
which is accomplished by the use of electronic devices
of a door closer when released.
for driving the lift motor at variable speed.
2.16 Door Closer — A device which automatically
2.12.6 Alternating Current Variable Voltage (ACW)
closes a manually opened door.
Control — A system of speed control which is
accomplished by varying the driving and braking 2.17 Door Operator — A power-operated device for
torque by way of voltage variation of the power supply opening and closing doors.
to the driving machine induction motor.
2.18 Dumb Waiters — A lift with a car which moves
2.12.7 Alternating Current Variable Voltage Variable in guides in a vertical direction; has a net floor area of
Frequency (ACVWF) Control — A system of speed 1 mz, total inside height of 1.2 m, whether or not
control which is accomplished by varying the voltage provided with fixed or removable shelves; has a
and frequency of the power supply to the driving capacity not exceeding 250 kg and is exclusively used
machine induction motor. for carrying materials and shall not carry any person.

2.12.8 Solid-State d.c. Variable Voltage Control — 2.19 Electrical and Mechanical Interlock — A
A solid-state system of speed control which is device provided to prevent simultaneous operation of
accomplished by varying the voltage and direction of both up and down relayk.
the power supply to the armature of driving machine
2.20 Electro-Mechanical Lock — A device which
d.c. motor.
combines in one unit, electrical contact and a
2.13 Counterweight — A weight or series of weights mechanical lock jointly used for the landing and/or
to counter-balance the weight of the lift car and part of car doors.
the rated load. 2.21 Emergency Stop Push or Switch — A push
2.14 Deflector Sheave — An idler pulley used to button or switch provided inside the car designed to
change the direction of a rope lead. open the control circuit to cause the lift car to stop
during emergency.
2.15 Door
2.22 Escalator — A power driven, inclined, continuous
2.15.1 Door, Centre Opening Sliding — A door which stairway used for raising or lowering passengers.

6 NATIONAL BUILDING CODE OF INDIA


.. ... ..

2.23 Escalator Installation — It includes the 2.37 Landing Call Push — A push button fitted at a
escalator, the track, the trusses or girders, the lift landing, either for calling the lift car, or for actuating
balustrading, the step treads and landings and all chains, the call indicator.
wires and machinery directly connected with the
2.38 Landing Door — The hinged or sliding portion
operation of the escalator.
of a lift well enclosure, controlling access to a lift car
2.24 Escalator Landing ——The portion of the at a lift landing.
building or structure which is used to receive or
2.39 Landing Zone — A space extending from a
discharge passengers into or from an escalator.
horizontal plane 400 mm below a lauding to a plane
2.25 Escalator Landing Zone — A space extending 400 mm above the landing.
from a horizontal plane 40 cm below a landing to a
plane 40 cm above the landlng. 2.40 Levelling Devices

2.26 Escalator Machine — The mechanism and other 2.40.1 Levelling Device, Li# Car — Any mechanism
equipment in connection therewith used for moving which either automatically or under the control of the
the escalator operator, moves the car within the levelling zone
towards the landlng only, and automatically stops it at
2.27 Floor Levelling Switch — A switch for bringing the landing.
the car to level at slow speed in case of double speed
or variable speed machines. 2.40.2 Levelling Device, One Way Automatic — A
device which corrects the car level only in case of under
2.28 Floor Selector — A mechanism forming a part run of the car but will not maintain the level during
of the control equipment, in certain automatic lifts, loading and unloading.
designed to operate controls which cause the lift car to
stop at the required landings. 2.40.3 Levelling Device, Two-Way Automatic
Maintaining — A device which corrects the car level
2.29 Floor Stopping Switch — A switch or
on both underrun and over-run and maintains the level
combination of switches arranged to bring the car to
during loading and unloading.
rest automatically at or near any pre-selected landing.
2.40.4 Levelling Device, Two Way Automatic Non-
2.30 Gearless Machine — A lift machine in which
Maintaining — A device which corrects the car level
the motive power is transmitted to the driving sheave
on both under run and over run but will not maintain
from the motor without intermediate reduction gearing
the level during loading and unloading.
and has the brake drum mounted directly on the motor
shaft. 2.41 Levelling Zone — The limited distance above
or below a lift landing within which the Ievelling
2.31 Goods Lift — A lift designed primarily for the
device may cause movement of the car towards the
transport of goods, but which may carry a lift attendant
landing.
or other persons necessary for the loading or unloading
of goods. 2.42 Lift — An appliance designed to transport
persons or materials between two or more levels in a
2.32 Guide Rails — The members used to guide the
vertical or substantially vertical direction by means of
movement of a lift car or counterweight in a vertical
a guided car or platform. The word ‘elevator’ is also
direction.
synonymously used for ‘lift’.
2.33 Guide Rails ‘Fixing — The complete assy.
2.43 Lift Car — The load carrying unit with its floor
comprising the guide rails bracket and its fastenings.
or platform, car frame and enclosing bodywork.
2.34 Guide Rails Shoe — An attachment to the car
2.44 Lift Landing — That’ portion of a building or
frame or counterweight for the purpose of guiding the
structure used for discharge of passengers or goods or
lift car or counter weight frame.
both into or from a lift car.
2.35 Hoisting Beam — A beam, mounted immediately
below the machine room ceiling, to which lifting tackle 2.45 Lift Machine — The part of the lift equipment
can be fixed for raising or lowering parts of the lift comprising the motor and the control gear therewith,
machine. reduction gear (if any), brake(s) and winding drum or
sheave, by which the lift car is raised or lowered.
2.36 Hospital Lift — A lift normally installed in
a hospital/dispensary/clinic and designed to 2.46 Ltit Pit — The space in the lift well below the
accommodate one number bed/stretcher along its level of the lowest lift landing served.
depth, with sufficient space around to carry a minimum 2.47 Lift Well — The unobstructed space within an
of three attendants in addition to the lift operator. enclosure provided for the vertical movement of the

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 7


lift car(s) and any counterweight(s), including the lift points automatically close their doors ond proceed on
pit and the space for top clearance. their trips in a regulated manner.

2.48 Lift Well Enclosure — Any structure which Typically, it includes one button in each car for eWh
separates the lift well from its surroundings. floor served and up and down buttons at each landing
2.49 Operation — The method of actuating the control (single buttons at terminal landings). The stops setup
of lift machine. by the momentary actuation of the car buttons ake made
automatically in succession as a car reaches the
2.49.1 Automatic Operation — A method of operation corresponding landings irrespective of its direction of
in which by a momentary pressure of a button the lift travel or the sequence in which the buttons are actuated.
car is set in motion and caused to stop automatically at The stops set up by the momentary actuation of the
any required lift landing. landing buttons may be accomplished by any lift in
2.49.2 Non-Selective Collective Automatic Operation the group, and are made automatically by the first
— Automatic operation by means of one button in the available car that approaches the landing in the
car for each landing level served and one button at corresponding direction.
each landing, wherein all stops registered by the 2.49.6 Car Switch Operation — Method of operation
momentary actuation of landing or car buttons are made by which the movement of lift car is directly under the
irrespective of the number of buttons actuated or of operation of the attendant by means of a handle.
the sequence in which the buttons are actuated. With
this type of operation, the car stops at all landings for 2.49.7 Signal Operation — Same as collective
which buttons have been actuated making the stops in operation, except that the closing of the door is initiated
the order in which the landings are reached after the by the attendant.
buttons have been actuated but irrespective of its 2.49.8 Double Button (Continuous Pressure)
direction of travel. Operation — Operation by means of buttons or
2.49.3 Selective Collective Automatic Operation — switches in the car and at the landings any of which
Automatic operation by means of one button in the may be used to control the movement of the car as
car for each landing level served and by up and down long as the button or switch is manually pressed in the
buttons at the landings, wherein all stops registered by actuating position.
the momentary actuation of the car made as defined 2.50 Operating Device — A car switch, push button
under non-selective collective automatic operation, but or other device employed to actuate the control.
wherein the stops registered by the momentary
actuation of the landing buttons are made in the order 2.51 Overhead Beams — The members, usually of
in which the landings are reached in each direction of steel, which immediately support the lift equipment at
travel after the buttons have been actuated. With this the top of the lift well.
type of operation, all ‘up’ landing calls are answered 2.52 Over Speed Governor — An automatic device
when the car is traveling in the up direction and all which brings the lift car and/or counter weight to rest
‘down’ landing calls are answered when the car is by operating the safety gear in the event of the speed in
traveling in the down direction, except in the case of a descending direction exceeding a predetermined limit.
the uppermost or lowermost calls which are answered
as soon as they are reached irrespective of the direction 2.53 Passenger Lift — A lift designed for the transport
of travel of the car. of passengers.

2.49.4 Single Automatic Operation — Automatic 2.54 Position and/or Direction Indicator — A device
operation by means of one button in the car for each which indicates on the lift landing or in the lift car or
landing level served and one button at each landing so both, the position of @e car in the lift well or the
arranged that if any car or landing button has been direction or both in which the lift car is traveling.
actuated, the actuation of any other car or landing
2.55 Rated Load (Lift) — The maximum load for
operation button will have no effect on the movement
which the lift car is designed and installed to carry
of the car until the response to the first button has been
safely at its rated speed.
completed.
2.56 Rated Load (Escalator) — The load which the
2.49.5 Group Automatic Operation — Automatic
escalator is designed and installed to lift at the rated
operation of two or more “non-attendant lifts equipped
speed.
with power-operated car and landing doors. The
operation of the cars is co-ordinated by a supervisory 2.57 Rated Speed (Lift) — The mean of the maximum
operation system including automatic dispatching speed attained by the lift car in the upward and
means whereby selected cars at designated dispatching downward direction with rated load in the lift car.

8 NATIONAL BUILDING CODE OF INDIA


w-

2.58 Rated Speed (Escalator) — The speed at which 2.67 Terminal Stopping Switch Normal — Switch
the escalator is designed to operate. It is the rate of for cutting all the energizing current in case of car
travel of the steps, measured along the angle of traveling beyond the top bottom landing or a switch
inclination, with rated load on the steps or carriage. cuts off the energizing current so as to bring the car to
stop at the top and bottom level.
2.59 Retiring Cam — A device which prevents the
lariding doors from being unlocked by the lift car unless 2.68 Terminal Stopping Device Final — A device
it stops at a landing. which automatically cause the power to be removed
from an electric lift driving machine motor and brake,
2.60 Roping Multiple — A system of roping where,
independent of the fimctioning of the normal terminaI
in order to obtain a multiplying the factor from the
stopping device, the operating device or any emergency
machine to the car, multiple falls of rope are runaround
terminal stopping device, after the car has passed a
sheave on the car or counterweight or both, It includes
terminal landing.
roping arrangement of 2 to-l.3 to 1 etc.
2.69 Total Headroom — The vertical distance from
2.61 Safety Gear — A mechanical device attached to
the level of the top lift landing to the bottom of the
the lift car or counterweight or both, designed to stop
machine room slab.
and to hold the car or counterweight to the guides in
the event of free fall, or, if governor operated, of over- 2.70 Travel — The vertical distance between the
speed in the descending direction. Any anticipated bottom and top lift handing served.
impact force shall be added in the general drawing or
2.71 Geared Machine — A machine in which the
layout drawing.
power is transmitted to the sheave through worm or
2.62 Service Lift — A passenger cum goods lift meant worm and spur reduction gearing. -“

to carry goods along with people.


3 GENERAL
Typically in an office building this maybe required to
3.1 The appropriate aspect of lift and escalator
carry food or stationeries, in a residential building to
installation shall be discussed during the preliminary
carry a bureau or accommodate a stretcher and in a
planning of the building with all the concerned parties,
hotel to be used for food trolleys or baggage. There is
namely, client, architect, consulting engineer ancl/or
a need in such lifts, to take care of the dimensions of
lift/escalator manufacturer. This enables the lift/escalator
the car and the door clear opening in line with the type
manufacturer to furnish the architect andlor consulting
of goods that may have to be carried based on mutual
engineer with the proposed layout on vice-versa.
discussion between supplier and customer. Also, such
lifts shall have buffer railings in the car at suitable 3.2 Exchange of Information
height to prevent damage to the car panels when the
goods are transported. Typically such lifts, if provided 3.2.1 If the proposed installation is within the scope
with an automatic door, may use some means to detect of 6, the guidelines laid down together with Fig. 1 will
enable the preliminary scheme for the installation to
trolleys and stretcher movement in advance to protect
be established.
the doors against damage. The car flodr load
calculations and car area of such a lift is as in the case Figure 1 shows only some of the typical arrangements
of a passenger lift except that these are not meant to and variations are possible with respect to number of
carry heavy concentrated loads. lifts and the layout,

2.63 Sheave — A rope wheel, the rim of which is Although the recommended outline for the various
grooved to receive the suspension ropes but to which classes of lifts given in 6 enables the general planning
the ropes are not rigidly attached and by means of details to be determined by the architect, these should
which power is transmitted from the lift machine to be finally settled at the earli~st possible stage by detailed
the suspension ropes. investigation with the purchaser’s representative
reaching agreement with the lift maker where necessary
2.64 SIack Rope Switch — Switch provided to open
before an order is finally placed. This will enable a
the control circuit in case of slackening of rope(s)
check to be made and information to be exchanged on
2.65 Suspension Ropes — The ropes by which the such vital matters as:
car and counter weight are suspended. a) the number, capacity, speed and disposition
2.66 Terminal S1OWDown Switch — A switch when of the lifts necessary to give adequate lift
actuated shall compulsorily cut off the high speed and service in the proposed building.
switch on the circuitry to run the lift in levelling speed b) the provision of adequate access to the
before reaching on terminal landings. machine room.

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIIWS AND ESCALATORS 9


f’-4,

1A STRAIGHT LINE 1B ALCOVE ARRANGEMENT FOR


ARRANGEMENT FOR THREE LIFTS FOUR LIFTS

1C ARRANGEMENT FOR SIX LIFTS 1D ARRANGEMENT FOR EIGHT LIFTS

FIG. 1 ARRANGEMENT
OF LIFTS

c) The loads which the lift will impose on the required before completion to allow for
building structure, and the holes to be left in testing;
the machine room floor and cut-outs for wall k) The requirements for electrical supply
boxes for push-buttons and signals; feeders, etc;
d) The necessity for and type of insulation to m) The requirements for scaffoicbg in the lift
minimize the transmission of vibration and well and protection of the lift well prior to
noise to other parts of the building; and during installation of equipment; and
e) The special requirements of local authorities n) Delivery and storage of equipment.
and other requirements set out in the ‘planning
permit’; 3.2.2 Information to be Provided by Architect or
Engineer
f] The need for the builder to maintain accuracy
of building as to dimensions and in plumb; As a result of preliminary discussion (see also 6), the
The periods of time required for preparation drawings of the building should give the following
g)
and approval of relevant drawings for particulars and finished sizes:
manufacturing and the installation of the lift a) Number, type and size of lifts and position of
equipment; lift well;
h) The requirements for fixing guide brackets b) Particulars of lift well enclosure;
to the building structure; c) Size, position, number and type of landing
j) The time at which electric power will be doors;

10 NATIONAL BUILDING CODE OF INDIA


d) Number of floors served by the lift; include the details of lifts (number of lifts duly
e) Height between floor levels; numbered, location, type, type of doors, passenger
Number of entrances; capacity and speed).
f)
g) Total headroom; 3.2.3 Working Drawings to be Prepared by the Liftl
h) Provision of access to machine room; Escalator Manufacturer

j) Provision of ventilation and, if possible, The lift/escalator manufacturer requires sufficient


natural lighting of machine room; information for the preparation of working drawings
k) Height of machine room; and is usually obtained from architect’s drawings
m) Depth of lift pit; supplemented by any information obtained from the
n) site and by collaboration with tie other contractors.
Position of lift machine, above or below lift
well; 3.2.3.1 Working drawings showing the layout of liftl
P) Size and position of any trimmer joists or escalator duly numbered, details of builders work, for
stanchions adjacent to the lift well at each example, holes in walls for guide fixing, holes in
floor; machine room floor for ropes and conduits, recesses
q) Size and position or supporting steel work at for landing sills, supports for lift/escalator machine and
roof levels; loads imposed on the building should be submitted by
r) the liftiescalator manufacturer to the architect/engineer
Size and position of any footings or gnllage
foundations, if these are adjacent to the lift for written approval.
pit; and
3.3 Electrical Requirement
s) In the case of passenger lifts whether the lift
cage is required to carry household luggage, For information of the electrical engineer, the lift/
such as refrigerator, steel almirah, etc. escalator manufacturer should advise the architect
engineer of his electrical requirements. This information
3.2.2.1 The lift lobby should be designed appropriately should be available early in the planning stage so that
since this has bearing on the traffic handling especially the electrical supply requirements of the lift(s)/
when more number of lifts are involved. In a dual line escalator(s) may be included in the electrical provisions
arrangement (lifts opposite to each other) the lobby of the building and that suitable cables and switchgear
can be between 1.5 times to 2.5 times the depth of one may be provided.
car. Typically, the more the number of lifts the bigger
the multiple to be used. As an example a quadmplex 3.4 The requirements given under 4 to 13 deal with
may use 1.5 to 2 times where as an octoplex will need installation of lifts and 14 deal with the installation of
2 to 2.5 times. For in-line (single line) arrangements, escalators.
the lobby can be typically half of the above
4 ESSENTIAL REQUIREMENTS
recommendations.
4.1 Conformity with L@s Act and Rules
It is preferable that the lift lobby is not used as a
thoroughfare but in such cases the lift corridor shall The installation shall be generally carried out in
take into account space for people who are moving. conformity with Lifts Act and Rules thereunder,
wherever they are in force.
3.2.2.2 The architect/engineer should advise the lift
manufacturer, if the Authority has any special 4.1.1 It is the responsibility of the owner of the
requirements regarding lifts in buildings in the premises where the lift will be installed, to obtain
administrative area concerned. necessary permission from the Authority before and
after the erection of lifts and for subsequent operation
3.2.2.3 The information contained under 3.2.1
of lift(s).
and 3.2.2 is applicable for the installation of lifts only
and in the case of escalator installations, the drawings” 4.2 Conformity with Indian Electricity Act and
shall provide the appropriate information. Rules
3.2.2.4 The architecdengineer should inform the liftl
All electrical work in connection with installation of
escalator manufacturer of the dates when the erection
electric lifts shall be carried out in accordance with
of the liftiescrdator may be commenced and is to be
the provisions of The Indian Electricity Act, 2003 and
completed so that sufficient time is allowed for the
the provisions framed thereunder as amended from
manufacture and erection of the liftlescalator.
time to time, and shall also comply with the other
3.2.2.5 When submitting application for a building provisions of Part 8 ‘Building Services, Section 2
permit to the local Authority, the building plans shall Electrical and Allied Installations’.

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 11


4.3 Conformity with Indian Standards c) One-half of the gravity stopping distance
based on:
4.3.1 All materials, fittings, appliances etc used in
1) 115 percent of the rated speed where oil
electrical installation shall conform to Indkm Standard
buffers are used and no provision is
specifications wherever these exist. In case of materials
made to prevent the jump of the car at
for which Indian Standard specifications do not exist,
counterweight buffer engagement; and
the materials shall be approved by the competent
authority. For detailed specification for lifts, reference 2) Governor tripping speed where spring
shall be made to accepted standards [8-5(2)]. buiTers are used.
NOTE— The gravitystoppingdktaoce based on
4.4 Conformity with Fire Regulations thegravityretardationfromanyinitialvelocitymay
be calculatedaccordingto the followingformula
4.4.1 The installation shall be carried out in conformity S=51W
with Part 4 ‘Fire and Life Safety’ and local tire regulations where
and rules thereunder wherever they are in force. s= Free fall in mm (gravity stopping
distance), and
4.5 Factor of Safety v= Initial velocity in m/s

The minimum factor of safety for any part of the lift d) 600 mm.
shall not be less than five. Higher factor of safety for Where there is a projection below the ceiling of the
various parts shall be applicable in accordance with well and the projection is more than 500 mm, measured
accepted standards [8-5(3)]. horizontally from the centre line of the cross-head but
over the roof of the car, a minimum vertical clearance
4.6 Additional Requirements for Passenger and not less than that calculated above shall also be
Goods Lifts available between the roof of the car and the projection.
4.6.1 Bottom and Top Car Clearances Provided that the vertical clearance between any
4.6.1.1 Bottom car clearance equipment mounted on top of the car and the nearest
overhead obstruction shall be not less than the sum of
When the car rests on its fully compressed buffer there the three items (a), (b) and (c) as calculated above plus
shall be a vertical clearance of not less than 600 mm 150 mm.
between the pit floor and the buffer striker plate or the
lowest structural or mechanical part equipment or 4.6.2 Bottom Runby for Cars and Counterweights
device installed. The clearance shall be available 4.6.2.1 The bottom runby of cars and counterweights
beneath the whole area of the platform except fo~ shall be not less than the following:
a) guide shoes or rollers, safety jaw blocks, a) 150 mm where oil buffers are used;
platform aprons, guards of other equipment b) Where spring-buffers are used;
located within 300 nun measured horizontally
1) 150 mm for controls as in 2.12.4 to 2.12.S.
from the sides of the car platform; and
2) Not less than the following for controls
b) compensating sheaves.
as in 2.12.2 to 2.12.3.
Provided that in all the cases, including small cars, a Rated speed Runby
minimum clearance of 600 mm is available over a In/s mm
horizontal area of 800 mm x 500 mm. Up to 0.125 75
Provided also that in all the cases, when the car rests on 0.125 to 0.25 150
its fully compressed buffers, there shall be a vertical 0.25 to 0.50 225
clearance of not less than 50 mm between any part of 0.50 to 1 300
the car and any obstruction of device mounted in the 4.6.3 Maximum Bottom Runby
pit.
In no case shall the maximum bottom runby exceed
4.6.1.2 Top car clearance the following:
The vertical clearance between the car cross-head and a) 600 mm for cars; and
the nearest overhead obstruction within 500 mm b) 900 mm for counterweights.
measured horizontally to the nearest part of the
crosshead when the car platform is level with the top 4.6.4 Top Counterweight Clearances
lauding, shall be not less than the sum of the following; The top counterweight clearance shall be not less than
a) The bottom counterweight runby. the sum of the following four items:
b) The stroke of the counterweight buffer used. a) the bottom cw runby;

12 NATIONAL BUILDING CODE OF INDIA


w

b) thestroke of thecar buffer used; b) Compression of the buffer spring or height


c) 150 mm; and of the wooden block used as buffer, and
d) one-half the gravity stoppipg distance based c) 150 mm to compensate for gravity stopping
on distance for counterweight and any
future repairs to rope connections at the
1) one hundred and fifteen percent of the
counterweight at the car ends or at the
rated speed where oil buffers are used and
suspension points.
no provision is made to prevent jump
of the counterweight at car buffer 4.7.1.4 Runby for Cars and Counterweights
engagement; and
The bottom runby for cars and counterweights shall
2) governor tripping speed where spring
not be less than 150 mm.
buffers are used.
4.7.1.5 Maximum bottom runby
4.7 Additional Requirements for Service Lifts
In no case shall the maximum bottom runby exceed
4.7.1 Top and Bottom Clearances for Car and
300 mm.
Counterweights
4.8 In order to maintain a safe work environment, and
4.7.1.1 Top car clearance
to avoid potential hazards, the following shall be
The top car clearance shall be sufficient to avoid any provided:
protruding part fixed on the top of the car coming in
a) caution sign shall be instrdled in the areas
direct contact with the ceiling or diverting sheave.
listed below where potential hazard exists:
The clearance shall be calculated taking into account 1) Trip hazard in machine room; and
the following and shall not be less than the sum of the 2) Caution notice against unauthorized use
following four items: of rescue devices (for example, brake
a) The bottom counterweight runby, release device).
b) The stroke of the counterweight buffer b) Use the hard hats for entry in pit and car top
used, during construction period. .
c) The dimensions of the portion of the diverting c) Warning sign shall be provided on the
sheave hanging underneath the ceiling in the controller so also eliminate, the possibility of
lift well, and contact with any exposed or concerded power
circuit.
d) 150 mm for compensating for gravity stopping
distance and future repairs to the rope d) Car top barricade system shall be provided
connections at counterweight and at the car as primtiy protection against fall, on car
or at the suspension points. top.
e) Whenever work is carried out on the lift and
4.7.1.2 Bottom car clearance
lift is not required to be moved on power,
The bottom car clearance shall be maintained in such notice shall be put on electrical main switch
a way that the counterweight shall not come in contact indicating requirement of de-energized
with the ceiling or any part hanging underneath the condition.
ceiling, when the car completely rests on fully f) During lift installation/maintenance, protection
compressed buffers, provided the buffers are spring against fall shall be provided with suitable
type mounted on solid concrete or steel bed. barricades for all open lending entrances.
In case of wooden buffers the bottom car clearance 4.9 Planning for Dlmemions
shall be maintained in such a way that the total
downward travel of the car from the service level of 4.9.1 General
the immediate floor near the pit, shall not be more than The dimensions of lift well have been chosen to
the top counterweight clearance, when the wooden accommodate the doors inside the well which is the
buffers are completely crushed. normal practice. In special cases, the door may be
4.7.1.3 Top counterweight clearance accommodated in a recess in the front wall, for which
prior consultation shall be made with the lift
The top clearance for the counterweight can be
manufacturer.
calculated taking into account the following and shall
not be less than the sum of the following three items: 4.9.2 Plan Dimensions

a) Car runby, 4.9.2.1 All Plan dimensions of lift well are the

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 13


minimum clear plumb sizes. The architect/engineer, safety is required under conditions stipulated in good
in conjunction with the builder, shall ensure that practice [8-5(3)], the tabular values should be revised
adequate tolerances are included in the building design in consultation with the lift manufacturer.
so that the specified minimum clear plumb dimensions
4.9.2.5 For outline dimensions of lifts having more
are obtained in the finished work.
than one car entrance, lift manufacturers should be
NOTE — The words ‘clear plumb dimensions’ should be noted consulted.
particularly in case of high rise buildings.
4.9.3 Outline Dimensions
4.9.2.2 Rough opening in concrete or brick walls to
accommodate landing doors depend on design of 4.9.3.1 The outline dimensions of machine-room, pit
architrave. It is advisable to provide sufficient depth, total headroom, overhead distance and sill for
allowances in rough opening width to allow for four classes of lifts to which the standard applies are
alignment errors of opening at various landings. specified in Tables 1 to 4 as indicated below:

4.9.2.3 When more than one lift is located in a Passenger lifts Table 1 and 1A
common well, a minimum allowance of 100 mm for Goods lifts Table 2
separator beams shall be made in the widths shown in Hospital lifts Table 3
Tables 1 to 4.
Service lifts Table 1 and 1A
4.9.2.4 Where the governor operated counterweight Dumb Waiter Table 4

Table 1 Recommended Dimensions of Passenger Lifts and Service Lifk


(Clauses 4.9.2.3 and 4.9.3.1)
All dimensions in millimetres.

r 50 min.
WINDOW
-—. — .
.—. 1 1
IT I 9 1
H C.L
. OF HOISTII NG

BEAMSIHOOKS
T
II

II
BEAIJAIJ

H s \
lt- 8 —--
I

TERRACE IIg
II
11
LEVEL
II r
I

h I
OVERHEAD

2000 min.
ENTRANCE

i-

SILL PROJECTION
RCC / STEEL

TRiVEL

\\d
#
BO170M
LANDING
\ I
1, * /7

H_
\, J’
_.’J ‘4.-
PIT MACHINE ROOM WIDTH
DEPTH

ELEVATION PLAN

14 NATIONAL BUILDING CODE OF INDIA


q “J (:?
i

Table 1 — Concluded

Load Car Side Lift Well Entrance


~ ~ f—-’-.
Persons kg A B c D E
(1) (2) (3) (4) (5) (6) (7)
4 272 1100 700 1900 1300 700, Min
6 408 1100 1000 1900 1700 700, Min
8 544 1300 1100 1900 1900 800
10 680 1300 1350 1900 2100 800
13 884 2000 1100 2500 1900 900
16 1088 2000 1300 2500 2100 1000
20 1360 2000 1500 2500 2400 1000

Table 1A Recommended Dimensions of Pit, Overhead and Machine-Room


for Passenger Lifts and Service Liffi
(Clauses 4.9.2.3 and 4.9.3.1)

All dimensions in millimetres.

Speed in mh up to 0.70 >0.7051.00 >1.00 s 1.50 >1.50<1.75 >1.75 s 2.00 >2.00 S 2.50
(1) (2) (3) (4) (5) (6) (7)

Pit
depth 1350 1500 1600 2150 2200 2500
Overhead 4200 4250 4800 4800 5200 5400
Machine-room D+2000 D+2500
Depth e’

Machine-room C+looo C+ 1200 C+ 1500


Width

NOTES
1 The total overhead dimension has been calculated on the basis of car height of 2.3 m.
2 In case of manually operated doors, clear entrance will be reduced by the amount of projection of handle on the landing door.
3 All dimensions given above for lifts having centre opening power operated doors with counterweight at rear, are recommended
dimensions primarily for architects and building planners. Any variations mutually agreed between the manufacturer and the purchaser
are permitted. However, variation in:
a) Car inside dimensions shall be within the maximum area limits specified in accordance with accepted standards [8-5(4)].
b) Entrance width on higher side is permitted.
c) Entrance width on lower side is permitted up to 100 mm subject to minimum of 700 mm.
4 Dimensions of pit depth and overhead may differ in practice as per individual manufacturer’s design depending upon load, speed
and drive. Recommended dimensions for pit depth, overhead and machine-room for different lift speeds are given in Table 1A.
However, the pit depth and overhead shall be such as to conform to the requirements of bottom clearance and top clearance in
accordance with the accepted standards [8-5(5)].

. 4$

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 15


Table 2 Recommended Dimensions of Goods Lifts
(For Speeds Up to 0.5 mh)

(Clauses 4.9.2.3 and 4.9.3.1)


All dimensions in millimetres.

.—-—-—-—.—-
r -—-—-—-1 -—-
1
I
A
r
I

1
I

-14 -—
I
I
I
.— . .-
t - I
I

I
I
I
I

I I
I
I

I I
!!!&
I

TOP LANDING I
I
d

R!Q
L
SIL !50

I
I
~A~
1- E~
II

I I
-
‘+1 II
#
~
id II
z
>
S
1-
II
!1
BOTTOM
LENDING ~ I II
II

II

‘-=”’””7
L MACHINE ROOM = C+ 2000
49’

PLAN *
ELEVATION

Load Car Inside Lift Well Entrance


kg \ /’ \
A B c D E
(1) (2) (3) (4) (5) (6)

500 1100 1200 1900 1500 1100


1000 1400 1800 2300 2100 1400
1500 1700 2000 2600 2300 1700
2000 1700 2500 2600 2800 1700
2500 2000 2500 2900 2800 2000
3000 2000 3000 2900 3300 2000
4000 2500 3000 3400 3300 2500
5000 2500 3600 3400 3900 2500

NOTES
1 The width of machine room shall be equal to be lift well width ‘C’ subject to minimum of 2500 mm.
2 The total headroom has been calculated on the basis of a car height of 2.2 m.
3 Clear entrance width ‘E’ is based on vertical lifting car-door and vertical biparting landing doors. For collapsible mid-bar doors the
clear entrance width will be reduced by 200 mm (maximum 1800 mm).
4 All dimensions given above are recommended dimensions primarily for architects and building planners. Any variations mutually
agreed between the manufacturer and the purchaser are permitted. However, variation in car inside dimensions shall be within the
maximum area limits in accordance with accepted standards [8-5(4)].
5 Dimensions of pit depth and overhead may differ in practice as per individual manufacturer’s design depending upon load, speed
and drive. However, the pit depth and overhead shall be such as to conform to the requirements of bottom clearance and top clearance
in accordance with accepted standards [8-5(5)].
.

16 NATIONAL BUILDING CODE OF INDIA


Table 3 Recommended Dimensions of Hospital Liits
(For Speeds Up to 0.5 rids)

(Clauses 4.9.2.3 and 4.9.3.1)


All dimensions in rnillimetres.

.—-—
-
-—-— I
I
h=
II
I

I
1’
I L- —---- -
—1
1 —

I
I
II
II
1

II
II

II
II
I
-E-
-A-

II
II u
,-
‘‘ FT—---7
!!’\\ /“’ IIII !
“~\/’
II ~ II

11!/x\ ! II

lib’‘O
‘
~‘kL—_LJ
-—-—-—-
II

-—-—-—- -u

r,
BOTTOM LENDINGT

L MACHINE
(,~~n,
ROOM = C
J
PIT
DEPTH
PLAN

ELEVATION

Load Car Wide Lift well Entrance


T A > r A > / A Y
Persons kg A B c b E
(1) (2) (3) (4) (5) ‘6) (7)

15 1020 1000 2400 1800 3@ m


20 1360 1300 2400 2200 30@) 1200
26 1768 16(X) 2400 2400 3000 1200

NOTES
1 The total headroom has been calculated on the basis of a car height of 2.2 m.
2 In the case of manually-operated doors, clear entrance will be reduced by the amount of projection of handle on the landing door.
3 Although 15 persons capacity lift is not standard one, this is included to cover lifts of smaller capacity which can be used in small
hospitals.
4 AO dimensions given above are recommended dimensions primarily for mhitects and building planners. Any variations mutually
awed betw=n the manufacturer and the pumhaser are permitted. However, variation in car inside dimensions shallbe within the
maximum area liits in accordance with accepted standarda [8-5(4)].
5 Dimensions of pit depth and overhead may differ in practice as per individual manrrfactumr’sdesign depending npon load, speed
and drive. However, the pit depth and overhead shall be such as to conform to the requirements of bottom clearance and top clearance
in accordance with accepted standards [8-5(5)1.

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 17


Table 4 Recommended Dimensions of Dumb Waiter
(For Speeds Up to 0.5 mk)

(Clauses 4.9.2.3 and 4.9.3.1)


All dimensions in millimetres.

I
I

PLAN

iii
>
s
t-

BOTTOM LANDING
(SERVICE LEVEL)

ELEVATION

Load Car Inside Lift Well Entrance


kg ~ /—’—,
A B H c D E
(1) (2) (3) (4) (5) (6) (7)
100 700 s 700 800 1200 900 700
150 800 800 900 1300 1000 800
200 900 900 1000 1400 1100 900
250 1000 1000 1200 1500 1200 1000

NOTE — Entrance width ‘E’ is based on assumption of provision of vertical biparting doors (no car door is
normally provided).

18 NATIONAL BUILDING CODE OF INDIA


P-’--

4.9.3.2 Travel d) The forces required on the structure in the


event of car buffering directly without safety
The tables have been established for a maximum travel
gear application to be indicated in the general
of 30 m. For travels above 30 m, the lift manufacturer
arrangement drawing.
shotdd be consulted.
4.10.2 Liji Well Enclosures
4.9.3.3 Pit
4.10.2.1 Lift well enclosures shall be provided and
The pit depth of the lifts will normally accommodate
shall extend on all sides from floor-to-floor or stair-
compensating chains. If compensating ropes are
to-stair, and shall have requisite strength and in proper
required, pit depth shall be increased for all loads and
plumb.
speeds and lift manufacturer should be consulted.
4.10.2.2 The inner sides of the lift well enclosures
4.9.3.4 Minimumfloor to j700r height
facing any car entrance shall, as far as practicable form
Minimum floor to floor height for landings on same a smooth, continuous flush surface devoid of
side for horizontally sliding f + 750 mm and
door is projections or recesses.
for vertically biparting doors is 1.5 f+ 250 mm, where
NOTE— Thisrequirementmaybe met in existing lift wells by
‘~’ is clear entrance height in mm. tilting any recesses or spaces between projections or alternatively
by covering them with suitable sheet material. If it is not possible
4.10 Lift Wells and Lift Well Enclosures to render flush any objection or tops of recesses, they should be
beveled on the underside to an angle of 60°, from the horizontal
4.10.1 Lijt Wells by means of metat plates, cement rendering or other fwe-resisting
materiats. Where a car-levelling device is operative with car
4.10.1.1 No equipment except that forming a part of door opening, such interior surfaces shatl always forma smooth
the lift or necessary for its operation and maintenance flush surface below each landing level for a depth to at least the
shall be installed in the lift well. For this purpose, the depth of the car-levelling zone plus the distance through which
main supply lines shall be deemed to be a part of the the lift car may travel of its own momentum when the power is
cut-off.
lift and the underground cable, if laid along the lift
well shaft, shall be properly clamped to the wall. 4.10.2.3 Where an open lift well would increase the fue
risk in a building, the lift well enclosure shall be of fwe-
4.10.1.2 Sufficient space shall be provided between
resisting construction (see Part 4 ‘Fire and Life Safety’).
the guides for the cars and the side walls of the lift
well enclosure to allow safe and “easy access to the 4.10.2.4 Where wire grill or similar constructions is
parts of the safety gears for their maintenance and used, the mesh or opening shall be such that the
repairs; safety gears provided shall be in accordance opening between the bars shall reject the ball of 30 mm
with good practices [8-5(3)]. in diameter and the lift well enclosure shall be of
sufficient strength to resist accidental impact by users
4.10.1.3 Lift wells, together with the whole of the
of the staircase or adjoining floors or by materials or
contained equipment and apparatus, shall be rendered ftre
trucks being moved in the vicinity.
resistant to the greatest possible extent (see also 4.4.1).
4.10.2.5 Where the clearance between the inside of
4.10.1.4 Every counterweight shall travel in juxtaposition
an open-type lift well enclosure and any moving or
to its car in the same lift well.
movable part of the lift equipment of apparatus is less
4.10.1.5 It is undesirable that any room, passage or than 50 mm, the openings in the enclosure shall be
thoroughfare be permitted under any lift well. If further protected by netting of square mesh of aperture
unavoidable spaces for other uses may be permitted not greater than one centimeter and of wire not smaller
under the lift well, with the prior approval of the Lift than one mm. (The provisions of this clause need not
Inspectorate Authority and the following provisions be adhered to for lift wells imfactory premises, coming
shall be made: under the purview of Factories Act. In such cases
provisions of 4.10.2.4 is sufficient.)
a) Spring or Oil buffers shall be provided for
lift car and counterweight; 4.10.2.6 There shall be no opening in the lift well
b) The pit shall be sufficiently strong to enclosure permitting access to the lift car by passing
withstand stt~cessfully the impact of the lift under the counterweight.
car with rated load or the impact of the 4.10.2.7 In case of a completely enclosed lift well, a
counterweight when either is descending at notice with the word ‘Lift’ may be placed outside of
rated speed or at governor tripping speed; each landing door.
c) The car and the counterweight shall be
4.10.2.8 Indicator
provided with a governor-operated safety
gear; and Where lifts are installed in totally enclosed wells,

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 19


position indicators are recommended to be provided 4.11.4 The room shall be kept closed, except to those
at each floor; however, where position indicators are who are concerned with the operation and maintenance
not provided, at least direction indicators or ‘In Use’ of the equipm?nt. When the electrical voltage exceeds
indicators shall be provided at each landing. 220/230 V ac, a danger notice plate shaJl be displayed
permanently on the outside of the door and on or near
4.10.2.9 Landing doors
the machinery. Where standby generator is provided,
Every lift well shall, on each side from which there is it is necessary to connect fire,- lift to ,$e s~dby
access to a car, be fitted with a door. Such a door shall generator. Depending upon the capcity of the standby
be fitted with efficient electromechanical locking so generator one or more other lifts may also b connected
as to ensure that it cannot be opened except when the to the supply.
lift car is at landing and that the lift car cannot be moved
Rescue instniction with required tools and tackles if
away from the landing until the door is closed and
any shall be made available in the machine room.
locked. If the door is mechanically locked, means
should be provided for opening the same by means of All lifts which do not have any automatic transfer
special key during emergency or inspection. facility to an alternate supply, such as generators, shall
be equipped with Battery Operated Automatic Rescue
4.10.2.10 Automatic devices for cutting off power
Device to bring the lift to the nearest floor and open
An efficient automatic device shall be provided and the door in the event of power failure.
maintained in each lift whereby all power shalI be cut
4.11.5 The machine room shall be equipped with an
off from the motor before the car or counterweight
insulated portable hand lamp provided with flexible
lands on buffer.
cord for examining the machinery.
4.10.3 Lift Pits
4.11.6 If any machine room floor or platform does
4.10.3.1 A lift pit shall be provided at the bottom of not extend to the enclosing walls, the open sides shall
every lift. be provided with hand rails or otherwise suitably
guarded.
4.10.3.2 Pits shall be of sound construction and
maintained in a dry and clean condition. Where 4.11.7 The machine room shall not be used as a store
necessary, provision shall be made for permanent room or for any purpose other than housing the lift
drainage and where the pit depth exceeds 1.5 m suitable machinery and its associated apparatus and equipment.
descending arrangement shall be provided to reach the
4.11.8 Machine room floor shall be provided with a
lift pit. And a suitable fixed ladder or other descending
trap door, if necessary. The size of the trap door shall
facility in the form of permanent brackets grouted in
be as per manufacturer’s recommendation.
the wall extending to a height of 0.75 m above the
lowest floor level shall be provided. A light point with 4.11.9 The height of the machine room shall be
a switch shall also be provided for facility of sufficient to allow any portion of equipment to be
maintenance and repair work. accessible and removable for repair and replacement
and shall be not less than 2 m clear from the floor or
4.11 Machine Rooms and Overhead Structures the platform of machine whichever is higher.
4.11.1 The lift machine, controller and all other 4.11.10 It will’ be noted that generally lifts have
apparatus and equipment of a lift installation, excepting machine rooms immediately over the lift well, and this
such apparatus and equipment as function in the lift should be arranged whenever possible without
well or other positions, shall be placed in the machine restricting the overhead distance required for normal
room which shall be adequately lighted and rendered safety precautions. In qase where machine room
fire-proof and weather-proof. provision on top is a limitation, either machine room
4.11.2 The motor generators controlling the speed of less lift or basement drive or side drive lift can be
multi-voltage or variable voltage machines, secondary considered.
sheaves, pulleys, governors, floor selecting equipment 4.11.11 For detailed information regarding nomenclature
may be placed in a place other than the machine room, of floors and storeys, reference maybe made to good
but such position shall be adequately lighted, ventilated practice [8-5(6)].
and rendered fire-proof and weather-proof.
4.11.12 There should be a proper access planned for
4.11.3 The machine room shall have sufficient floor approach to the machine room taking into account need
area as well as permit free access to all parts of the for maintenance personnel to access the machine room
machines and equipment located therein for purposes at all times of day and night and also the need to take
of inspection, maintenance or repair. heavy equipment. Any fixture such as a ladder

20 NATIONAL BUILDING CODE OF INDIA


provided should be secured permanently to the 4.12.4 Passenger lifts shall be provided with power
structure and should have railings to reduce the risk of operated doors which are imperforate.
falling.
5 DIMENSIONAL TOLERANCES
4.11.13 It is desirable that emergency exit may be
provided in case of large machine rooms having four 5.1 Lift Well Dimensions
or more lifts. Plan dimensions of lift wells given by the lift maker
4.11.14 Where the machine room occupies a prominent represent the minimum clear plumb sizes. The
position on roof of a building, provision should be purchaser’s representative, in conjunction with the
made for lightning protection in accordance with good builder, should ensure that adequate tolerances are
practice [8-5(7)] and Part 8 ‘Building Services, included in the building design so that the specified
Section 2 Electrical and Allied Installations’. minimum plumb dimensions are obtained in the
finished work,
4.11.15 Wherever the machine room is placed, it
should be properly ventilated. The ambient temperature Dimensions in excess of these minimum plumb
of machine room shall be maintained between + 5°C dimensions for lift well and openings (but not less)
and + 40”C. can be accommodated by the lift maker up to certain
maximum values beyond which changes in design
4.11.16 If located in the basement, it should be may be necessary involving additional expense or
separated from the lift well by a separation wall. work by the builder. The purchaser’s representative
should take these factors into account when
4.12 Essential Features Required
specifying the lift well structural dimensions on the
4.12.1 Power operated car doors on automatically basis of the constructional tolerance appropriate to
operated lifts shall be so designed that their closing the building technique.
and opening is not likely to injure a person. The power
operated car door shall be provided with a sensitive 5.2 Landing Door Openings
device which shall automatically initiate reopening of It is very important that finished landing openings
the door in the event of a passenger being struck or is should be accurate to design size and plumb one above
about to be struck by the door, while crossing the the other for the full travel of the lift. In constructing
entrance during closing movement. The effect of the the structural openings in concrete walls to lift wells it
device may be neutralized: is not possible to achieve a degree of accuracy
a) during the last 58 mm of travel of door panel vertically which will allow doors and frames to be
in case of side opening doors inserted in the opening without some form of masking
or packing to overcome inaccuracies. Provisions
b) when panels are within 58 mm of each other
should therefore be made in design by increasing the
in case of center opening doors.
nominal height from design finished floor level and
The force needed to prevent the door from closing shall width of openings to each jamb and head.
not exceed 150 N and this measurement shall not be
In addition, the alignment of the outer face of the front
made in the first third of the travel of the door.
wall of the lift well is of importance when architrave
In order to achieve this it is desirable that all power of fixed dimensions are called for, and in this case the
operated doors have a full length (covering at least 80 alignment of the outer face from floor to floor should
percent of the car door height tiom the bottom) intia not vary to a greater extent than can be accommodate
red light curtain safety to retract the door in the event of by the subsequent front wall finish, the architrave being
coming across any obstacle during closing of the door. set accurately plumb.
4.12.2 Single speed and two speed drives which are To facilitate accurate align’rnent of landing sills it is
poor in levelling accuracy and energy consumption common practice to provide at each landing an
shall not be used for new lifts in view of availability of independent threshold, the position of which can be
latest technology energy efficient Variable Voltage adjusted.
Variable Frequency drive systems with improved
leveling accuracy. 5.3 Structural Limits for Lift Wells at any Level

4.12.3 For passenger lifts with car call button control If the net plumb well (dimensions A and B of Fig. 2)
in car and with capacities of 16 passenger and above, and the nominal structural entrance openings
it is recommended to have an additiomd car operating (dimensions C and D of Fig. 2) are defined by plumb
panel with call buttons on the opposite side to main lines, the actual wall should not encroach on these
pane} for ease of access to buttons. dimensions.

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 21


Dimension K (inside face of wall of Fig. 2) should fall NOTE — It is recommended to do Ttilc Anatysis Study to
ensore optimum provision of lifts for the building in consultation
within the following limits:
with lift manufacturers. In view of the dynamic situation it is
For wells upto 30 m – O-25 mm recommended that a computerised software is used for Traffic
Analysis Study.
For wells upto 60 m – O-35 mm
For wells upto 90 m - 0-50 mm 6.1.2 The number of passenger lifts and their
capacities, that is load and speed, required for a given
When architrave are to be supplied by the lift maker building depend on the characteristics of the building.
dimension L (side of structural opening of Fig. 2) The most important of these are:
should fall within the limits of O and 25 mm and
a) Number of floors to be served by the lift;
dimension M (outer face of the front wall of Fig. 2)
should not vary to a greater extent than can be b) Floor to floor distance;
accommodated by the subsequent front wall finish, the c) Population of each floor to be serve~ and
architrave being set accurately plumb. d) Maximum peak demand; this demand maybe
When the entrance linings are supplied by the builder, unidirectional, as in up and down peak
corresponding provision should be made for the periods, or a two-way traffic movement.
finished openings to be accurately plumb one above It should be appreciated that all calculations on the
the other for the full travel of the lift end to design traffic handling capabilities of lifts are dependent on a
size. number of factors which vary according to the design
of lift and the assumptions made on passenger actions.
-tKr-’q+r It follows, therefore, that the result of such calculations
can only be put to limited use of a comparative nature.
For instance, they can with advantage be used to
compare the capabilities of lifts in a bank with different
loads and speeds provided the same set of factors are
used for all cases. On the other hand, they cannot be
used to compare the capabilities of different makes of
lift used for a given bank of lifts.

Different authorities and manufacturers differ widely


in their methods of calculation, due to the variations
in lift performance, especially with regard to rates of
acceleration and deceleration and door operation times
I --+-+-+L-
I-D-A
1 which form the components of performance
Therefore, the calculations
time.
made by different
L--C-I
organizations will not necessarily agree.
FIG. 2 LIFE WELL TOLERANCE
6.2 Preliminary Lift Planning
6 PRELIMINARY DESIGN
6.2.1 General
6.1 Number of Lifts and Capacity
Methods of calculating the trtilc handling capabilities
6.1.1 Two basic considerations, namely, the quantity of lifts were first devised for office buildings. In due
of service required and the quality of service desired, course detailed modifications were devised to suit other
determine the type of lifts to be provided in a particulm applications ‘without altering the basic principles. The
building. Quantity of service gives the passenger application to office buildings is still the most
handling capacity of the lifts during the peak periods frequently used.
and the quality of service is measured in terms of
waiting time of passengers at various floors. Both these Therefore, the following method may be used as
basic factors require proper study into the character of general guidance on preliminary lift planning for
the building, extent and duration of peak periods, offices, bearing in mind the differences set out
frequency of service required, type and method of in 6.1.2.
control, type of landing doors etc. In busy cities A lift installation for office building is normally
patience, coefficient being low satisfaction cannot be designed to populate the building at a given rate and
obtained if lifts with adequate capacities and speeds the three main factors to be considered are:
are not provided. In view of many variables, no simple
formula is possible for determining the most suitable a) population or the number of people who
lifts. require lift service.

22 NATIONAL BUILDING CODE OF INDIA


b) handling capacity of the maximum flow rate requirement in an office building. The employees of
required by these people. all offices are subject to discipline and are required to
c) interval or the quality of service required. be at their place in time. Consequently, the incoming
traffic flow is extremely high and the arrival time is
6.2.2 Population over a short period.
The first point to be ascertained from the eventual Sometimes it becomes necessary to reduce the
occupier is the total building population and whether maximum traffic flow by staggering the arrival of the
this is likely to increase in the future, employees so that different groups arrive at different
If a definite population figure is unobtainable an times, This reduces the peak and also the requirement
assessment should be made from the net area and of lifts. However, many organizations may object to
probable population density. Average population staggering and prefer to have all employees arrive at
density can vary from about one person per 4 m2 to the same time since it is claimed that staggering will
one person per 20 m2. It is essential, therefore, that affect the proper co-ordination of business.
some indication of the probable population density 6.2.6 Capacity
should be obtained from the building owner. If no
indication is possible (a speculative development for The minimum size of car recommended for a single
example) population in the region of 5 m2 per person purpose buildings is one suitable for a duty load of
for general office buildings is usually assumed. 884 kg. Generally, for large office buildings cars with
capacities up to 2040 kg are recommended according
6.2.3 Quantity of Service to the requirements.
The quantity of service is a measure of the passenger 6.2.7 Speed
handling capacity of a vertical transportation system.
It is measured in terms of the total number of It is dependent upon the quantity of service required
passengers handled during each five-minute peak and the quality of service desired (see 6.2.3 and 6.2.4).
period of the day. A five-minute base period is used as Therefore, no set formulae for indicating the speed
this is the most practical time over which the traffic can be given. However, the following general
can be averaged. recommendations are made:

The recommended passenger handling capacity for No. of Floors Speed


various buildings is as follows:
4t05 0.5 to 0.75 In/s
6 to 12 0.75 to 1.5 rnh
Type of Building Handling Capacity
3 to 20 1.5 tllh to 2.5 dS
Office — Diversified tenants 10 to 15 percent
Above 20 2.5 rrds and above
Office — Single tenant 15 to 25 percent
Residential 7.5 percent
6.2.8 Layout

6.2.4 Quality of Service The shape and size of the passenger lift car bears a
distinct relation to its efficiency as a medium of traffic
The quality of service on the other hand is generally
handling. A study of the most suitable proportions for
measured by the passenger waiting time at the various
these lifts reveal that the width of the lift well entrance
floors. The following shall be the guiding factor for
is in reality, the basic element in the determination of
determining this aspect.
the best proportions. In other words, the width of the
Quali~ of Service or Acceptable Interval car is determined by the width of the entrance and the
depth of the car is regulated by the loading per square
20 to 25 seconds Excellent
metre permissible under this Code. Centre opening
30 to 35 seconds Good doors are more practicable and efficient entrance units
34 to 40 seconds Fair for passenger lifts.
45 seconds Poor
6.2.9 Determination of Transportation or Handling
Over 45 seconds Unsatisfactory Capacity During the Up Peak
NOTE — For residential buildings longer intervals should
be permissible. 6.2.9.1 The handling capacity is calculated by the
following formula:
6.2.5 Trajj$ic Peaks
H 3OOXQX1OO
The maximum traffic flow during the up peak period =
is usually used as a measure of the vertical transportation TxP

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 23


where the design of the equipment related to opening and
closing of the landing and car doors, acceleration,
H = Handling capacity as the percentage of the
deceleration, levelling and passenger movement. These
peak population handled during 5 min
factors are discussed below:
period,
Q = Average number of passengers carried in a a) The most important factor in shortening the
car, time consumed between the entry and the exit
T = Waiting interval in seconds, and of the passengers to the lift car is the correct
design of the doors and the proper car width.
P = Total population to be handled during peak
For comfortable entry and exit for passengers
morning period. (It is related to the area
it has been found that most suitable door
served by a particular bank of lifts.)
width is 1000 mm and that of car width is
The value of Q depends on the dimensions of the car. 2000 mm.
It maybe noted that the car is not loaded always to its b) The utilization of centre opening doors has
maximum capacity during each trip and, therefore, for been a definite factor in improving passenger
calculating H the value of Q is taken as 80 percent of transfer time, since when using this type of
the maximum carrying capacity of the car. door the passengers, as a general rule, begin to
The waiting interval is calculated by the following move before the doors have been completely
formula: opened. On the other hand, with a side
opening door the passengers tend to wait until
T=RIT the door has completely opened before
N moving.
where
The utilization of centre opening doors also favours
T = Waiting interval in seconds, the door opening and closing time periods. Given the
N = Number of lifts, and same door speed, the centre opening door is much
R7T = Round trip time, that is, the average time faster than the side opening type. It is beyond doubt
required by each lift in taking one full that the centre opening door represents an increase in
load of passengers from ground floor, transportational capacity in the operation of a lift.
discharging them in various upper floors
6.2.9.2 An example illustrating the use of the above
and coming back to ground floor for taking
consideration is given below:
fresh passengers for the next trip,
Gross area per floor 1 100m2
RTT is the sum of the time required in the following
Net usable area per floor 950 m’
process:
No. of landings including 15
a) Entry of the passengers on the ground floor,
ground
b) Exit of the passengers on each floor of
Assuming population density 9.5 m2 per person
discharge,
Probable population in
c) Door closing time before each starting
operation, ~ = 14X950
d) Door opening time on each discharging 9.5
operation, Upper floors 1400 persons
e) Acceleration periods,
Taking 20 passengers lift with
f) Stopping and levelling periods, 2.5 nds the calculated RTT 165 S

g) Periods of full rated speeds between stops


Q=20x0.8= 16
going up, and
h) Periods of full rated speeds between stops a) Taking No. of lifts, N = 4
going down.
RTT 165 = ~ls
It is observed that the handling capacity is inversely T=—=—
N4
proportional to waiting interval which in turn is
proportional to R7T. Reducing the RTT of a lift from H . 3OOXQX1OO _ 3OOX16X1OO
120 to 100 increases its handling capacity by TxP – 41x1400
20 percent.
= 8.3 percent
The round trip time can be decreased not only by
increasing the speed of the lift but also by improving b) Taking No. of lifts, N= 6

24 NATIONAL BUILDING CODE OF INDIA


~=~ 6.4.2 Passenger Lifis
= 27.6 S
6 6.4.2.1 Low and medium class flats

~ = 3OOXQX1OO = 3OOX16X1OO Where a lift is arranged to serve two, three or four


TxP 27.6x1 400 flats per floor, the lift may be placed adjoining a
staircase, with the lift entrances serving direct on to
= 12 percent the landings. Where the lift is to serve a considerable
number of flats having access to balconies or corridors,
6.3 Quiet Operation of Lifts
it may he conveniently placed in a well ventilated tower
Every precaution should be taken with passenger lifts adjoining the building.
to ensure quiet operation of the lift doors and
6.4.2.2 OJfice buildings, hotels and high class flats
machinery. The insulating of the lift machine and any
motor generator from the floor by robber cushions or In general the arrangement as recommended in 6.4.1
by a precast concrete slab with rubber cushions, is to be followed. However, in case this is not possible,
prevents transmission of most of the noise. In this it is desirable to have at least a battery of two lifts at
connection, see also good practice [8-5(8)] and Part 8 two or more convenient points of a building. If this is
‘Building Services, Section 4 Acoustics, Sound not possible, it is advisable to have at least two lifts
Insulation and Noise Control’ for some useful side by side at the main entrance and one lift each
recommendations. at different sections of the building for inter-
communication. When two lifts are installed side by
6.4 Positioning of Lifts
side, the machine room shall be suitably planned with
A thorough investigation should be made for assessing sufficient space for housing the machine equipment.
the most suitable position for lift(s) while planning the The positioning of lifts side by side gives the following
building. It should take into account future expansions, advantages:
if any. Though each building has to be considered
a) all machines and switch gear may be housed
individually for purposes of location of lifts, factors
in one machine room,
influencing the locations of passenger and goods lifts
are given in 6.4.2 to 6.4.4. b) the lifts can be inter-connected more
conveniently from an installation point of
The location of lifts may also conform to the travel view, and
distance requirements specified in Part 4 ‘Fire and Life
c) greater convenience in service owing to the
Safety’.
landing openings and each floor being
6.4.1 Arrangement of Lifls adjacent.

The lifts should be easily accessible from all entrances 6.4.2.3 Shops and departmental stores
to the building. For maximum efficiency, they should
Lifts in shops and stores should be situated so as to
be grouped near the centre of the building. It is preferably
secure convenient and easy access at each floor.
not to have all the lifts out in straight line and, if possible,
not more than three lifts should be arranged in this 6.4.2.4 For buildings with more than 12 floors, it is
manner. It has to be kept in mind that the corridor should recommended to have provision of 1 stretcher/service
be wide enough to allow sufficient space for waiting lift in addition to the passenger lifts.
passengers as well as for through passengers.
6.4.2.5 For buildings with more than 12 floors, where
6.4.1.1 In some cases when there are more than three passenger and service lifts are provided in one lobby
lifts, the alcove arrangement is recommended. With it is recommended to have group control for all the
this arrangement, the lift alcove lead off the main lifts.
corridor so that there is no interference by traffic to
6.4.3 Goods Lifts
other groups or to other parts of the ground floor. This
arrangement permits the narrowest possible corridors The location of lifts in factories, warehouses and
and saves space on the upper floors. Walking distance similar buildings should be planned to suit the
to the individual lift is reduced and passenger standing progressive movement of goods throughout the
in the center of the group can readily see all the lift buildings, having regard to the nature of position of
doors and landing indicators, The ideal arrangement the loading platforms, railway sidings, etc. The placing
of the lifts depends upon the particular layout of the of a lift in a fume or dust laden atmosphere or where it
respective building and should be determined in may be exposed to extreme temperatures, should be
every individual case. Some typical recommended avoided wherever possible. Where it is impossible to
arrangements are given in Fig. 1. avoid installing a lift in an adverse atmosphere, the

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIIT’S AND ESCALATORS 25


electrical equipment should be of suitable design and supports based on ultimate strength of the material and
construction to meet the conditions involved. load in accordance with 6.5.4 shall be not less than the
following:
6.4.3.1 Normally goods lifts have lower speeds than
passenger lifts for the same travel because traffic For Steel 5
conditions are less demanding, and more time is For Reinforced Concrete 7
required for loading and unloading.
The deflection of the overhead beams under the
6.4.3.2 As loads for goods lifts increase in size and maximum static load calculated in accordance with
weight, so the operation of loading and unloading above shall not exceed 1/1 500 of the span.
becomes more difficult. Therefore, it is usual to require
greater accuracy of levelling as the capacity of the 6.6 Access to Machine Room and Lift Pits
goods lift increases.
6.6.1 Access to machine room above a lift well may
6.4.3.3 A large capacity goods lift at high speed is be either from the roof or by an internal staircase with
often a very uneconomical preposition. The inherent a proper arrangement for fixing.
high cost is enhanced due to the very small demand
6.6.2 Access between a secondary floor and a machine
for such equipment, much of which is custom made.
room may be by ladder. Where a machine room
The high capital cost of the lift, building work and
entrance is less than 1.5 m above or below the adjacent
electrical supply equipment usually shows a much
floor or roof surfaces, a substantial permanently
smaller return as an investment than more normal sizes
attached ladder may be used. Ladders shall be fixed at
of lifts.
least 150 mm clear of any wall, beam or obstruction
6.4.4 Hospital Bed Lifis and shall extend at least to the landing level. Above
the landing level and for a height of at least 1.15 m,
Hospital bed lifts should be situated conveniently near
either the ladder stringers shall be extended or suitable
the ward and operating theatre entrances. There shall
hand grips shall be provided.
be sufficient space near the landing door for easy
movement of stretcher. 6.6.3 Where the machine room entrance is 1.5 m or
more above or below the adjacent floor or roof surface,
It is convenient to place the passenger lifts in a hospital,
access shall be provided by means of stairs in accordance
near the staircases.
with the requirements given in 6.6.3.1 to 6.6.3.6.
6.5 Structural Considerations
6.6.3.1 The angle of inclination of the stair shall not
6.5.1 Lift we[l enclosures, lift pits, machine rooms and exceed 50° from the horizontal and the clear width of
machine supports besides conforming to the essential the stair shall be not less than 600 mm.
requirements given in 4, should form part of the
6.6.3.2 The tread shall have a non-slip surface which
building construction and comply with the lift
shall be not less than 150 mm wide for open stair
manufacturer’s drawings.
construction and not less than 20 cm wide for closed
6.5.2 Machine Room stair construction.

Floors shall be designed to carry a load of not less 6.6.3.3 The rise of the stair shall not exceed 250 mm.
than 350 kglmz over the whole area and also any load
6.6.3.4 A hand rail shall be provided on the outer
which may be imposed thereon by the equipment used
stringer of all stairways fixed at a convenient height,
in the machine room or by any reaction from any such
but not less than 500 mm high measured vertically from
equipment both during periods of normal operation
the nosings, and not less than 1 m high on landings
and repair.
and platforms. Such hand rail shall have atleast 50 mm
6.5.3 The side wall of the lift well may be made of clearance between nearest permanent object at the
reinforced cement concrete at least 150 mm thick so corresponding side of the stair.
as to provide satisfactory anchoring arrangement for
6.6.3.5 Headroom clearance of not less than 2 m
fixing. Reference shall also be made to Part 6 ‘Structural
measured from the nosings of the stairway, shall be
Design, Section 5 Plain, Reinforced and Prestressed
provided on every stairway.
Concrete, 5A Plain and Reinforced Concrete’.
6.5.4 The total load on overhead beams shall be 6.6.3.6 Heights of stairs over 5 m in length shall be
assumed as equal to all equipment resting on the beams provided with intermediate landings.
plus twice the maximum load suspended from the NOTE — Where compliance with any of the requirements
beams. specified in 6.61 to 6.6.3 is impracticable, applications for
variation shall be made to the Authority, who may, vary such
6.5.5 The factor of safety for all overhead beams and requirements.

26 NATIONAL BUILDING CODE OF INDIA


r--

6.6.4 Access to a machine room in a basement may controlled by this switch shall cancel all
be provided from a corridor. existing car calls and separate from
landing calls and no landing or car calls
6.6.5 Access to a machine room via the lift well shall
shall be registered. The buzzer and
be prohibited.
“fweman’s lift” light shall be turned on.
6.6.6 The lift pit should be capable of being examined All heat and smoke sensitive door re-
by a separate access. In the case of a battery of two opening devices shall be rendered
lifts, it is possible to examine the lift pit through the inoperative.
adjoining one. 2) If the lift is traveling towards the
evacuation floor, it shall continue driving
6.7 Fire Protection
to that floor.
To prevent fire from spreading by means of the lift 3) If the lift is traveling away from the
well, lift well enclosures shall conform to the evacuation floor, it shall reverse its
requirements given in Part 4 ‘Fire and Life Safety’. direction at the nearest possible floor
The machine room should be constructed of a suitable without opening its doors and return non-
grade of fire-resisting material and precautions should stop to the evacuation floor.
be taken to minimize spread of fire from the machine 4) If the lift is standing at a floor other than
room into the lift well (see also 7.3.14). the evacuation floor, it shall close the
doors and start traveling non-stop to the
6.8 Requirements for Fireman’s Lift
evacuation floor.
6.8.1 For buildings having height of 15 m or more 5) When at the evacuation floor the lift shall
atleast one lift shall meet the requirements of fireman’s park with doors open.
lift as given in 6.8.2. 6) The buzzer is turned off after this return
6.8.2 The fireman’s lift shall have the following drive.
minimum requirements: b) Fireman’s service (Phase 2):

a) Lift car shall have floor area of not less than The phase 2 operation of the lift shall be as
1.44 square meters. It shall also have a defined below.
loading capacity of not less than 544 kg 1) The phase 2 is started after phase 1, if
(8 persons). the switch is “ON.
b) Lift landing doors shall have a minimum of 2) The lift does not respond to landing calls
fire resistance of one hour. but registers car calls. AIl heat and smoke
c) Doors shall be of automatic operation for car sensitive door reopening devices are
rendered inoperative.
and landing.
3) When the car call button is pressed the
6.8.3 Fireman’s lifts in a building having more than doors start closing. If the button is
15 m or more height, shall work at or above the speed released before the doors are fully closed,
of 1.0 nds so as to reach the top floor from ground they re-open. The car call is registered
level within one minute. only when the doors are fully closed.
6.8.4 Operation Requirements of Fireman’s Lijit 4) After registering a car call the lift starts
driving to the call. If more than one car
The lift shall be provided with the following as a
call is registered, only the nearest call is
minimum:
answered and the remaining calls will be
a) A two position switch at evacuation floor cancelled at thq fwst stop.
(normally main entrance floor) (ON/OFF), 5) At the floor the doors are opened by
and pushing the door open button. If the
b) Buzzer and ‘Fireman’s lift’ — light in car button is released before the doors are
fully open, they re-close.
6.8.4.1 Sequence of operation:
6) The lift returns to normal service when it
a) Return to evacuation floor (Phase 1): stands at the evacuation floor with doors
1) Shall start when the switch at the open and the switch is “OFF”.
evacuation floor is turned to the “ON’
6.9 Supply Cables and Switches
position or the signal from smoke
detector (if provided by the Building Each lift should be provided with a main switch or
Management System) is on. All lift(s) circuit breaker of a capacity determined by the lift

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 27


manufacturer and the incoming supply cable should and temperature conditions a lift is checked for the car
terminate in this switch. For a single lift, this switch to complete one round trip with contract load plus 10
should be fixed adjacent to the machine room entrance percent at nominal supply voltage and nominal ambient
inside the machine room. In a machine room common temperature. There is also a static test with contract
to more than one lift, each main switch should be load plus 25 percent to check that the brake will sustain
conveniently situated with respect to the lift it controls. the car.
Switches and fuses (which may form part of a
It is unnecessary to specify and additional overload
distribution switch-board) should be provided for
test or capacity and in fact it is detrimental to the norm@
isolating the supply cables to the machine room.
running efficiency and safety of the lift to do so.
6.10 The detailed design considerations for different
7.1.6 Occasional Extra Load
types and selection of the lifts shall be done in
accordance with good practice [8-5(5)]. It is not good practice to request that a lift should be
designed to carry an occasional extra load. It is
7 POWER AND CONTROL SYSTEMS tantamount to specifying an excessive overload test
7.1 Features Associated with Power Systems which is detrimental to the normal running efficiency
and safety of the lift.
7.1.1 Industrial Switchgear
7.2 Description of Operation Systems
Switchgear for controlling lift power systems is
characterized by its high duty cycle and its high 7.2.1 Methods of Control Systems
rupturing capacity. Switchgear must be robust enough The methods of control systems areas follows:
and shall be so designed as to withstand the high duty
cycle and high rupturing capacity introduced during a) Attendant and dual control (see 7.2.2), and
the operation of the lifts. b) Automatic push button operation (see 7.2.2).

7.1.2 Levelling Accuracy 7.2.1.1 Types of control systems

The levelling tolerances in accordance with good a) Collective control (see 7.2.3),
practice [8-5(4)] are those which can be reasonably b) Single push button collective control (see
expected between no load and full load in either 7.2.4),
direction. c) Down collective control (see 7.2.5),
Where greater levelling accuracy is required, careful d) Directional collective control for one car (see
examination should be made to see whether such 7.2.6),
increased precision is justified or practical. Advice e) Directional collective control for two or three
should also be obtained, as additional apparatus and cars (see 7.2.7), and
cost may be involved, and in some cases the Group supervisory control (see 7.2.8).
f)
requirement may not be practicable.
Features of control systems are described in 7.3.
7.1.3 Corrective Levelling
7.2.2 Automatic Push Button Operation
This should only be used when it is impossible
Automatic control is a method of operation by which
otherwise to achieve the required levelling tolerances
a momentary pressure on a push button sets the car in
or on long travel lifts to maintain the required levelling
motion and causes it to stop automatically at any
tolerances during loading and unloading.
required lift landing. This is the simplest control system
7.1.4 Levelling with Variable Voltage and it is sometimes referred to as push button control.
A variable voltage system is one using continuous A car answers a landi’ng or car call whichever is
regulation which minimizes speed differences due to actuated first by momentary pressure provided the lift
load variation. Therefore, the actual levelling speed is is not in use. Momentary pressure of a car push button
of less importance than the general refinement of its will send the car to the designated floor. The car always
regulation control. In fact no levelling speed as such responds to a car pushbutton in preference to a landing
may be identifiable. push button.
7.1.5 Overload Tests With this type of control, a RED landing signal light
or direction arrow indicates that the car is in use that is
A lift is designed to operate and transport the contract
the lift is traveling.
load at the required duty cycle, and should not by
intention or habitually be used to carry overloads. This type of control is recommended for the following
During test as a safeguard to cover variable supply applications.

28 NATIONALBUILDING CODE OF INDIA


a) A single passenger lift serving up to 4 floors. traffic. Two or three car banks have interconnected
b) Goods lifts serving any number of floors control.
where it is usually the most suitable form of With this type of control the following signals are
control, included:
For special purposes, the following two systems may a) A landing signal light indicates that the call
be considered: has been registered and will be answered.
a) Despatch from landings as an additional b) Illuminated car position indicator above car
feature for a goods lift with manually operated entrance.
doors. The call is registered by pressing the
7.2.6 Directional Collective Control for One Car
car push button and when the doors are closed
the car will travel to the designated floor. Directional collective control for one car is a control
b) Automatic with attendant control as an system having UP and DOWN push buttons at
additional feature on goods lifts with a key intermediate landings whereby the call is registered
operated switch in the car to transfer the for the intended direction of travel. Calls from the car
control from normal automatic to attendant or landing push buttons are registered and stored until
operation. There is also a visurd call indicator answered. The car will answer calls in floor sequence
with buzzer in the car to indicate to the in one direction of travel. Calls for the opposite
attendant the landing floors at which push direction of travel are answered when the direction of
buttons have been pressed when the car is travel is reversed.
under attendant control. This system is suitable for single lifts serving 4 or more
7.2.3 Collective Control floors with interfloor traffic, such as small office
blocks, hotels and blocks of flats.
Collective control is a generic term for those methods
of automatic operation by which calls made by pressing With this type of control the following signals are
push buttons in the car and at lifi landings are registered included:
and answered by the car stopping in floor sequence at a) A landing signal light for each landing push
each lift landing for which calls have been registered button indicates that the call has been
irrespective of the order in which the calls have been registered and will be answered.
made, and until all calls have had attention. b) Illuminated car position indicator above the
Collective control of any form is usually not suitable entrance in the car.
for goods lifts except where loading is not expected to c) Arrow shaped signal lights in the back of the
fill the car and additional loads can be taken at other car or on the landing to indicate to the entering
stops. person in which direction the car is going to
depart.
7.2.4 Single Push Button Collective Control
7.2.7 Directional Collective Control for Two or Three
Single push button collective control has a single push
Cars
button at each landing. It is not recommended, as the
direction in which it is desired to travel cannot be Directional collective control for two or three cars is a
registered by the intending passenger. system covering a control in which the two or three
cars in a bank are interconnected. One pushbutton unit
7.2.5 Down Collective Control
with UP and DOWN push buttons or floor buttons (in
Down collective is a control system where landing calls case of car control from floor) are required at each
are registered from a single push button, irrespective landing and the call system is common to all lifts. If
of the car being in motion or the landing door being for architectural balance, in the case of a three car bank,
open and calls are stored until answered. Any number extra push button units are required, these should be
of car calls can be registered and the car will stop in specified. Each landing call is automaticrdly allocated
sequence in the down direction at each of the to the best placed car. The control is designed so that
designated floors. The car will travel in the up direction cars are effectively spaced and thus give even service.
to the highest call registered stopping only in response When a car reaches the highest floor to which there is
to car calls. It will then travel downwards answering a call its direction of travel is automatically reversed
calls in floor sequence. If only one call has been when it next starts. One or more cars will return to the
registered the car travels to the floor of call. parking floor.

This system is suitable where there is traffic between Automatically bypassing of landing calls when a car
the ground and upper floors only and no interfloor is fully loaded is an essential feature for three-car

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 29


banks. It is also necessary for two-car banks in offices. destination. All landing calls are bypassed and car
Other cars will continue to provide service to all floors. position indicators on the landing for this lift are not
illuminated. The removal of the key when the special
When three-car banks serve 7 or 8 floors and over,
operation is completed restores the control to normal
some form of automatic supervisory control (see 7.2.8)
service.
is generally necessary in the interest of efficiency.
7.3.2 Landing Call Automatic Bypass
With this type of control the following signals are
included: For collective operation, automatic bypassing of
landing calls can be provided. This device will bypass
a) A landing signal light for each landing push
landing calls when a car is fully loaded but the calls
button to indicate that the call has been
are not cancelled.
registered and will be answered.
7.3.3 Motor Generator Shut Down
b) Illuminated car position indicator above the
entrance in the car. Lifts controlled by variable voltage system automatically
c) Arrow shaped signal lights in conjunction shutdown when subject to an over-ndlng control which
with an audible single stroke gong or an puts them out of service under certain conditions; for
indication on the landing call push button example, no demand for lift service. They are
station above each landing entrance to automatically put back into service as required.
indicate to the waiting person(s) which car is 7.3.4 Basement Service
going to stop and in which direction it will
continue its course. For lifts with collective control when service is required
below the main parking floor, which is usually the
7.2.8 Group Supervisory Control ground floor, to a basement andJor a sub-basement,
A bank or group of intensive traffic passengers lifts the lift maker should be informed of the type of service
requires a supervisory system to co-ordinate the required, as special technical considerations are then
operation of individual lifts which are all on collective usually necessary.
control and are interconnected. 7.3.5 Hospital Service
The very nature of intensive service calls for a Lifts for carrying beds and stretchers require a car
sophisticated automatic supervisory control system so preference switch so than an attendant can have
as to match the speed capacity of these lifts. complete control of the car when required. This
The supervisory system regulates the dispatching of requirement should be specified as ‘car preference’ and
individual cars and provides service to all floors as it will function as described in 7.3.1. Otherwise such
different traffic conditions arise minimizing such lifts can have the same control systems as for normal
unproductive factors as idle cars, uneven service and passenger lifts, the choice depending on the number
excessive waiting time. The system will respond of floors served, the service required and the number
automatically to traffic conditions such as UP and of lifts.
DOWN peaks, balanced or light traffic and provides 7.3.6 Manually Operated Doors (Without Closers)
for other specialized features.
A ‘door open’ alarm should be provided to draw
If desired, a master station can be provided in the lift attention to a car or landing door which has been left
lobby which gives by indicators, visual information open.
regarding the pattern under which the system is
operating. Where the system is based on a definite 7.3.7 Automatically Power Closed Doors
.
programme, control means are provided for altering For passenger operation when the car arrives at a
the type of traffic programme. There are other facilities, landing the doors will automatically open and then
such as the removal of any lift from service. close after lapse of a time interval. This time interval
can be overruled by the pressure of a push button in
7.3 Features of Operation Systems
the car to give instant door closing.
7.3.1 Car Preference
An ‘open door’ push button is provided in the car to
Sometimes it is necessary to give a special personal reverse closing motion of the doors or hold them open.
service or a house service. When this service is required
7.3.8 Controlled Power Closed Doors
and for whatever purpose, it should be specified as
‘car preference’ is by a key operated switch in the car. When there are conditions that particularly affect the
The operation is then from the car only and the doors safety of passengers or damage to vehicles or trucks,
remain open until a car call is registered for a floor the closing of the doors should only be made by the

30 NATIONAL BUILDING CODE OF INDIA


continuous pressure of push buttons in the car or on cater for the required passenger traffic, it is essential
landings. that such switches should not stop the f~eman’s control
from being operative in the event of the lift being
A ‘door open’ alarm should be provided to draw
designated as a fireman’s lift. Service switches should
attention to a car or landing door which has been left
not be confused with maintenance switches which are
open. This means of operation is required for some
only used when it is dangerous to attempt to operate
forms of goods lifts.
the lift because maintenance work is actually in
7.3.9 Safe Operation of Doors progress. A control station fitted on top of the car is
regarded as a maintenance switch.
The safety of passengers passing through lift entrances
is fully covered by the provision of good practice 7.3.13 Fire Switch
[8-5(9)]. No modification of these provisions should
be specified. When required by the fire authority a fire switch has
to be provided, the function of which is to enable the
7.3.10 Director Service fire authority to take over the complete control of one
There are many forms of giving special service for or more lifts in an installation {see good practice
individuals, but they should always be avoided. They
[8-5(4)] }.
range from key operated switches at preferred landings 7.3.14 Push Buttons and Signals
to the complete segregation of one out of a bank of
lifts. It is obvious that any preferential treatment of It is most important that the purpose of every push
this nature can seriously jeopardize the efficiency of button and signal should be clearly understood by all
the service as a whole. When a bank of say three lifts passengers.
is installed to meet the anticipated traffic requirements 7.3.15 In public places where blind persons are
and then, when the building is occupies, one lift is expected to use the lifts it is recommended to provide
detached permanently for directors’ service, the traffic Brailey buttons.
handling can be reduced by a half rather than a third.
7.4 Electrical Installation Requirements
When preferential service is imperative, then the car
preference feature should be available (see 7.3.1). 7.4.1 General

7.3.11 Indication of Car Arrival The good practices [8-5(4)] states the requirements for
main switches and wiring with reference to relevant
As all lift cars are illuminated when available (in
regulations. The lift maker should specify, on a
service). It is recommended that this illumination be
schedule, particulars of full load current, starting
used to signal the arrival of a car at a landing in
current, maximum permissible voltage drop, size of
preference to special signals such as LIFT HERE signs
switches and other details to suit requirements. For
since signal lamps can fail when the lift is still operating
multiple lifts a diversity factor may be used to
satisfactorily.
determine the cable size and should be stated by the
The following is the practice adopted for vision panels lift manufacturer.
in doors:
It is important that the switches at the intake and in the
a) For lifts with manually operated car and machine room which are provided by the electrical
landing doors, vision panels are provided in contractor are the correct size, so that correctly rated
all doors; HRC fuses can be fitted. No form of ‘NO VOLT’ trip
b) For lifts with power operated car doors and relay should be included anywhere in the power supply
manually operated landing doors, vision of the lift.
panels are provided in the landing doors only; a) Power supply mains — The lift sub-circuit
c) For lifts with automatically opened car and from the intake room should”be separate from
landing doors, no vision panels are required; other building service.
and Each lift should be capable of being isolated
d) When vision panels are provided they should from the mains supply. This means of
comply with the requirements of good isolation should be lockable.
practice [8-5(4)]. b) For banks of interconnected lifts, a separate
sub-circuit is required for the common
7.3.12 Service Switches
supervisory system, in order that any car
When switches are provided to take cars out of service, may be shut down without isolating the
that is because the remaining cars in the group can supervisory control of the remainder.

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 31


c) Lighting — Machine rooms and all other with an alarm push which is wired to a terminal box in
rooms containing lift equipment should be the lift well at the ground floor by the lift maker. This
provided with adequate illumination and with alarm bell, to be supplied by the lift maker (with
a switch fixed adjacent to the entrance. At indicator for more than one lift) should be fixed in an
least one socket outlet, suitable for lamps or agreed position and wired to the lift well. The suppIy
tools, should be provided in each room. may be from a battery (or transformer) fixed in the
machine room or, when available, from the building
The supply to the car light should be from a separate
fire alarm supply.
circuit, and controlled by a switch in the machine room.
For multiple lifts with a common machine room a When a telephone is to be provided in the lift car the
separate supply should be provided for each car. The lift maker should fit the cabinet in the car and provided
car lighting supply should be independent of the power wiring from the car to a terminal box adjacent to the
supply mains. Plug should be provided with a light, lift well.
the switch for which should be in the lift well, and
accessible from the lower terminal floor entrance. The type of telephone should be stated in the enquiry.

When the alarm system is connected to a transformer 7.4.4 Earthing


or trickle charger, the supply should be t~en from the 7.4.4.1 The terminal for the earthing of the frame of
machine room lighting. the motor, the winding machine, the frame of the
7.4.2 Electric Wiring and Apparatus control panel, the cases and covers of the tappet switch
and similar electric appliances which normally carry
7.4.2.1 All electrical supply lines and apparatus in the main current shall beat least equivalent to a 5 mm
connection with the lift installation shall be so diameter bolt, stud or screw. The cross-sectional area
constructed and shall be so installed, protected, worked of copper earthing conductor shall be not smaller than
and maintained that there may be no danger to persons half that of the largest current-carrying conductor
therefrom. subject to an upper limit of 65 mm2 {see also good
7.4.2.2 All metal casings or metallic coverings practice [8-5(10)] ].
containing or protecting any electric supply lines of 7.4.4.2 The terminal for the earthing of the metallic
apparatus shall be efficiently earthed. cases and covers of door interlocks, door contacts, call
7.4.2.3 No bare conductor shall be used in any lift car and control buttons, stop buttons, car switches, limit
as may cause danger to persons. switches, junction boxes and similar electrical fittings
which normally carry only the control current (such
7.4.2.4 All cables and other wiring in connection with terminal being one specially provided for this purpose),
the lift installation shall be of suitable grade for the and the earth conductor should be appropriately sized
voltage at which these are intended to be worked and in accordance with good practice [8-5(10)].
if metallic covering is used it shall be efficiently
earthed. The size of earthing conductor shall be in accordance
with Part 8 ‘Building Services, Section 2 Electrical and
7.4.2.5 Suitable caution notice shall be affixed near Allied Installations’.
every motor or other apparatus in which energy is used
at a pressure exceeding 250 V. 7.4.4.3 The earthing conductor shall be secured
to earthing terminal in accordance with the
7.4.2.6 Circuits which supply current to the motor shall recommendations made in good practice [8-5(10)] and
not be included in any twin or multicore trailing cable also in conformity with the latest provisions of
used in connection with the control and safety devices. l?lectrici~ Act, 2003 and Rules framed thereunder from
time to time. “
7.4.2.7 A single trailing cable for lighting control and
signal circuit shall be permitted, if all the conductors 7.4.4.4 The exposed metal parts of electrical apparatus
of this trailing cable are insulated for maximum voltage installed on a lift car shall be sufficiently bonded and
running through any one conductor of this cable. eartherd.

7.4.3 Emergency Signal or Telephone 7.4.4.5 Where screwed conduit screws into electric
fittings carrying control current making the case and
It is recommendatory that lift car be provided either
cover electrically continuous with the conduit, the
with an emergency signal that is operative from the
earthing of the conduit maybe considered to earth the
lift car and audible outside the lift well or with a
fitting. Where flexible conduit is used for leading into
telephone.
a fitting, the fitting and such length of flexible conduit
When an alarm bell is to be provided each car is fitted shall be effectively earthed.

32 NATIONAL BUILDING CODE OF INDIA


7.4.4.6 One side of the secondary winding of bell information can be sensed by the Building
transformers and their cases shall be earthed. Management Systems).
h) Door Reopen Request (Summary of Door
7.4.4.7 Where there are more than one lift in a
Open, Light Curtr&, Photocell, Safety Edge
building, there should be a separate earth pit for the
Signals).
lifts.
7.5.6 Where it is desired that it should be possible to
7.5 Building Management Systems — Interface for control the lift from Building Management Systems,
Lifts
the following control signals can be provided.
7.5.1 Where more than three lifts are provided in a a) Normal to service/inspection mode change
building and especially when these are provided at over ,
different locations in the building a form of central
b) Fault Accept/Rest Input
monitoring may be provided. Such central monitoring
may be through a Building Management Systems, if (Using this input, the lift controller may be
provided in the building or through a display panel. allowed to clear an existing fault if this is
o’tier wise safe. It will be decided by the Lift
7.5.2 The following signals should be given to the manufacturer as to what faults can be
building management interface from each lift. cleared)
a) Alarm button in car, c) Car call to top most floor and bottom most
b) Door Zone or floor level information, floor of each lift.

c) Lift moving information, Where such control inputs are provided, it should be
d) Power on information, and with a pass word and login feature that allows one to
e) Lift position information. determine who has used these inputs and at what time.
Always such inputs should be through authorized
7.5.3 Each of these signals shall be provided through person only. The Building Management Systems
a potential free contact located in the lift machine should make all changeovers effective only when lift
room. The contacts shall be rated for 230 V at/l A or is not moving.
24 V dc/lA. A pair of wires should be used for each
potential contact. 7.5.7 Control inputs from Building Management
Systems should be through a potential free contact
7.5.4 The wiring between lift machine room to capable of carrying 24 V dc/lA or 230 V ac/lA. The
Building Management Systems shall be planned and wiring should be terminated in each lift machine room.
carried out by the builder along with other wiring in
the building. 8 CONDITIONS FOR OPTIMUM PRACTICE

7.5.5 The building management system should ensure 8.1 Lift Entrance Operation
that any position information is read only when the
8.1.1 General
lift is not moving (lift moving information) or is
capable of reading several times to detect a stable state. Every lift journey involves two horizontal movements,
in and out of the car, to one vertical movement. The
In addition to the signals above the following signals
type of door, and the operation of the doors, play a
may be added if required for the benefit of monitoring
main part in the service given, and should receive
the lift performance.
careful consideration.
a) A summary fault output to indicate a lift in
8.1.2 Goods Trafic
fault condition, which prevents the lift from
providing service. This summary fault Most types of goods traffic’ require relatively longer
condition shall include the most common loading and unloading times and manual doors are
faults such as safety circuit open. frequently used for economy and simplicity.
b) Service or inspection mode.
Power operation can be applied, especially for large
c) Attendant mode. entrances, to give automatic opening: the doors then
d) Fire mode. always open fully, reducing the risk of damage. For
e) Doors opening. many types of goods traffic, it is preferable for closing
Doors closing. though powered, to be controlled by continuous
f)
pressure button, rather than being automatically
g) Lift moving up.
initiated {see good practice [8-5(4)] }.
(In combination with lift moving and lift
moving up information, lift moving down For heavy duty lifts, a power operated vertically sliding

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 33


door preferred, this can be made extremely robust, and 8.5 Lighting and Treatment of Walls, Floors+ Etc
is capable of extension to very large entrances.
8.5.1 All machine rooms should be considered as plant
8.2 Painting at Works and on Site space, and conditions provided to permit reliable
operation of electrical switchgear and rotating
Lift equipment with normally receive a protective coat machinery, and be conducive to good maintenance.
of paint at works before despatch to site. Further
painting of lift equipment may be necessary and is Lighting should be provided to give at least 200 lux
normally in the form of a finishing coat and can take around the controller and machine. The machine room
place on site. Alternatively, the further painting of the walls, ceiling and floor should be faced in dust-resisting
equipment may be carried out at works as a finishing materials, tiles, etc, or painted as a minimum to stop
coat with normal touching up after site erection as may dust circulation which otherwise could damage rotating
be necessary. machinery and cause failure of switchgear. Machine
rooms should also be weatherproof and if ventilation
Any additional painting, due to site conditions during louvers are provided they should be designed and sited
erection andlor final operating conditions in the to prevent snow being driven through or to the
premises, is subject to negotiation between the lift apparatus.
maker and the purchaser.
8.5.2 Lift wells should be constructed to be
Decorative finishes are a subject for separate weatherproof and of a dust free surface material or
negotiation. should be painted to minimize dust circulation on to
moving apparatus and from being pumped by the car
8.3 Special Environments
movement into machine rooms or on to landings.
Standard equipment is suitable for use inside normal
Sufficient number of light points should be provided
residential, commercial and industrial buildings
in the lift shaft for proper illumination.
but when unusual environments are likely to be
encountered, the advice of the lift maker should be 8.5.3 Should a lift entrance open out into an area
sought at the earliest possible stage to enable the most expected to the weather the entrance should be
economic satisfactory solution to be found. Special protected by a suitable canopy and the ground level
mechanical protection and or electrical enclosures may slope up to the entrance to prevent during rain or
be necessary as well as compliance with statutory or surface drainage from entering the lift well through
other regulations and with the purchaser’s particular the clearances around the landing doors. Any push
requirements, which should be fully considered at the buttons so enclosed should be of weatherproof type,
time of enquiry. 8.6 Stairwell Enclosures
Examples of situations which necessitate special The location of lifts in stairwells is not recommended.
consideration are:
The use of stair stringers for fixing of guides normally
a) Exposure to weather, for example, car parks. involves extensive site measurement in order to
b) Low temperatures, for example, cold stores. fabricate purpose-made brackets. The resulting
c) High temperatures, for example, boiler plant. attachments are often unreliable and lacking in
d) Hosing-down for example, for hygiene or robustness. For stairwells of normal width, the span
decontamination. required for the lift machine support beams is
excessive and unless uneconomic sections are used the
e) Corrosive atmosphere, for example, chemical
deflections under varying load adversely affect the
works.
motor of the lift.
f) Dusty atmospheres, for example, gas plant.
The necessary provision of suitable continuous
g) Explosive and inflammable atmosphere, for
enclosures can be very expensive.
example gas plants, and petroleum and
polyester industries. 8.7 Handwinding Release Procedure and Indication

8.4 Ventilation of Machine Rooms The release procedure by handwinding should only
be carried out in an emergency and by authorized
Machine rooms shall be ventilated. They shall be such
persons who have received the necessary instruction
that the motors and equipment as well as electric cables
because it is dangerous for any other persons to attempt
etc, are protected as far as possible from dust, harmful
to do SO.
dusts and humidity. The ambient temperature in the
machine room shall be maintained between 5°C and Before attempting to move the car, it is imperative that
40”C. any person in the car be warned of the intention to

34 NATIONAL BUILDING CODE OF INDIA


move the car and that they do not attempt to leave the components and parts should be kept readily available
car until they are advised that it is safe to do so. Any for the persons responsible for the maintenance and
failure to carry out this precaution may render the replacement where necessary.
person concerned guilty of negligence should an
9.2 Particular attention may be directed for thorough
accident occur.
periodical examination of wire ropes when in service.
Before attempting to handwind the lift machine, it is Attention should also be directed to the thorough
vital that the supply is switched off at the main switch. examination of the groove of drums, sheaves and
pulleys when installing anew rope. A groove deepened
It is usually necessary to have two persons in the
by rope wear is liable to lead to early failure of a new
machine room: one to operate the brake release and
rope unless the groove is returned.
the other to carry out the handwinding. The
exceptions are small lift machines where the 9.3 Any accident arising out of operation of maintenance
handwinding and be easily controlled by one man and of the lifts should be duly reported to the Authority in
larger machines which need two men to operate the accordance with the rules laid down. A notice maybe
handwinding alone with an additional man to control put in the machine room to this effect.
the brake release.
10 LIFI’ENQUIRY OR JNVITATIONTO TENDER
If the car is stuck in the lift well and cannot be moved
when an attempt is made to move it in a downward 10.1 General
direction, then no attempt at handwinding should be A period of four weeks is normally sufficient for return
made because the car safety gear may have set. Any of tenders. This should be extended if large numbers
further procedure should be carried out under the of lifts or special requirements are involved.
instruction of a qualified lift mechanic.
The enquiry documents should be kept to the essential
Provided the car is free to be moved in the downward minimum, and should be strictly confined to material
direction, then it should be hand wound to the nearest relevant to the lift work and to the particular project
floor. There is a preference to move the car in a concerned
downward direction. However, this may not always
be practical owing to the distance involved and the When enquiring for and ordering an electrical lift in
time taken to complete the movement. In addition the accordance with this Section, the particulars given
amount of out of balance load on the counterweight below shall be furnished:
side, due to the size of car and the small number of
PARTICULARS OF LIFTS
persons inside it, may make it necessary to wind the
car upwards. In the case of higher speed lifts the 1) Type of lift (Passenger, goods, service or
direction of handwinding will usually be goverued by dumbwaiter) . . . . . . . . . . . . . . . . . . . . . . . .
the effort required to move the car because of the 2) Number oflifts required . . . . . . . . . . . . . . . . . . . . .
absence of a large gear reduction ratio. 3) Load: number ofpersons . . . . . . . . . . . . . ..kg . . . . . .
It is essential that all detail operations be carried out 4) Rated speed . . . . . . . . . . . . . . . . . . . ..rnls
according to the manufacturer’s instructions for the 5) Travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..m
lift concerned and these should be clearly stated and 6) Serving.. . . . . . . . . .. floors . . . . ..entrances . . . . . . .
permanently displayed in the form of a notice in the
7) Number of floors served . . . . . . . . . . . . . . . . . . . . .
machine room.
8) Method of control. . . . . . . . . . . . . . . . ..(see 7.2)
9 RUNNING AND MAINTENANCE 9) Position ofmachine room . . . . . . . . . . . . . . . . . .

9.1 The lift installation should receive regular 10) Sizes oflift well(s) . . . . . . . . . . . . . . . . . . . . .
cleaning, lubrication, adjustment and adequate 11) Position of counterweight ... ........ .......
servicing by authorized competent persons at such 12) Internal sizeof liftcar . . . . . . . . . . . . . . . . . . . . .
intervals as the type of equipment and frequency of 13) Construction, design and finish of car
service demand. In order that the lift installation is bodywork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
maintained at all times in a safe condkion, a proper
14) Car entrances:
maintenance schedule shall be drawn up in consultation
a) Number, size and type of doors
with the lift manufacturer and rigidly followed. The
provision of a log book to record all items relating to b) Power or manual operation
general servicing and inspection is recommended for 15) Cat-light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
all lifts. It is essential that the electrical circuit diagram 16) Call indicator . . . . . . . . . . . . . . position indicator
of the lift with the sequence of operation of different in cur . . . . . . . . . . . . . . . . . . . . . . . .

PART 8 BUILDING SERVICES — SECTION 5 INSTALLATION OF LIFTS AND ESCALATORS 35


17) Lift Landing Entrance: The lift maker should include such items as:
a) Number, size and type of doors or gates a) Guide brackets and wall inserts;
or shutters (for goods lifts)
b) Buffers and any associated steelworks;
b) Location of landing entrances in different Pit screen to counterweight;
c)
floors, if the car has more than one
d) Steel beams of raft for machine and pulleys;
opening.
e) Sound insulation to machine where this is
18) Electric Supply:
required;
Power . . . . . . . . . . . . . . . . . . volts acldc . . . . . . . . . . . . . . .
f) Doors;
phase . . . . . . . . . . . . . . . . . .
g) Door tracks;
Cycles . . . . . . . . . . . ..wire system . . . . . . . . . . . . . . . . . .
h) Supporting steelworks for horizontal sliding
19) Whether neutral wire available for control doors and frames for hinged doors;
circuit?
j) Wiring materials for the lift itself starting from
20) Lighting . . . . . . . . . . . . . ..volts ac/dc . . . . . . . . . . . . . . . the supplies furnished by the purchase~
cycles, . . . . . . . . . . . . . . . . .
k) Over current protection (type to be specified)
21) Are premises subject to Lifts Act/Rules? (see 7.4.1);
22) Proposed date for commencement on m) Alarm push and bell or telephone (see 7.4.3);
site . . . . . . . . . . . . . . . . . . . . . . . .
n) Alarm push and bell or telephone (see 7.4.3);
23) Proposed date for completion . . . . . . . . . . . . . . . . . .
P) Lifting tackle and small electric tools for use
24) Additional items, if required . . . . . . . . . . . . . . . . . ... during the actual installation;
25) Booklet giving complete details of maintenance
q) Services of erection staff to install and wire;
schedule and circuit diagram where so
r) Services of testing engineer and provision of
specified . . . . . . . . . . . . . . . . . . . . . . . .
the necessary instruments and test weights; and
10.2 Additional Items s) Guarantee of equipment.

The enquiry should state any additional items required The lift maker should exclude the supply and fixing of
beyond those specified in good practice [8-5(4)], such the items as the following:
as fireman’s control, radio interference suppression and
a) Builders’ work, such as forming lift well, pit
dismantling of existing lift, etc.
and machine room and building in wall
Lifts to be installed in adverse conditions, such as inserts;
chemical works, lifts used with power trucks, and b) Machine room floor including any
similar specialized applications, required individual reinforcement necessary for load bearing;
consideration according to the circumstances. c) Lifting beams in machine room where
necessary;
10.3 Finishes
d) Steel surrounds for vertical hi-parting sliding
Finishes should be specified at the enquiry stage or doors;
provisional sums should be included for them.
e) Any necessary tanking, lining or reinforcement
Finishes to be considered may include car body work, of the pit;
ceiling, floor, light fitting, ventilation, trims, car and f) Dividing beams for multiple wells, and
landing doors, including vision panels if required, interwell pit screens;
landing architrave push and indicator fittings, car and g) Temporary gust’ding of openings;
landings. h) Scaffolding, planks and ladde

You might also like