Scribd
Upload
2K views3 pages

Fanuc 6m

This document provides instructions for setting up a Fanuc 6M CNC machine and PC for direct numerical control (DNC) communication in drip feed mode. Key parameters and settings are listed to configure the machine controller, PC communication port and software, and null modem cable connection for transferring programs between the devices in blockwise format.

Uploaded by

Lưu Quý
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views3 pages

Fanuc 6m

This document provides instructions for setting up a Fanuc 6M CNC machine and PC for direct numerical control (DNC) communication in drip feed mode. Key parameters and settings are listed to configure the machine controller, PC communication port and software, and null modem cable connection for transferring programs between the devices in blockwise format.

Uploaded by

Lưu Quý
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Fanuc 6M

Set the following parameters on the machine


311 = 00011000
340 = 2
341 = 2
Set the setting data as follows
TV CHECK = 0
PUNCH CODE = 1
INPUT UNIT = 0
INPUT DEVICE 1 = 1
INPUT DEVICE 2 = 1
To set the controller in the Drip feed mode
Set the Tape mode on.
Note: The Dripfeed (Blockwise) program transfer works only when the dripfeed facility is enabled
on the machine controller.
Parameters for the various baud rates
For baud rates other than 2400 set as follows:
Baud rate Parameter
150
200
300
600
1200
2400
4800
9600
00010011
00010100
00010101
00010110
00010111
00011000
00011001
00011010
Set the following parameters on the PC
General settings
Machine name MCH-1
Control system Fanuc
Machine ID 01
Time out (sec) 5
Control program start M82
Control program end M30
Is DNC required Yes
DNC settings
Port Number COM2 (or any free COM port)
Baud rate 2400
Data bits 7
Parity Even
Stop bits 2
Handshake Hardware
Filter null character Yes
Transmit settings
Transmit directory Specify folder to store programs to be sent to machine from PC
Wait period at start of transmission 10.0
Wait period after transmitting program 5.0
Size of transmit packet 0
Delay period after each packet 0
Wait for XON before transmitting program No
Drip feed Off
Transmit comments? Yes
Comment start character (
Comment end character )
Translation mode for CR Transmit as CR
Translation mode for LF Transmit as LF
Program start string
Program end string
Receive settings
Receive directory Specify folder to store programs coming from machine
Wait period before receiving program 45.0
Wait period after receiving program 5.0
Transmit XON before transmitting program No
Auto compare and save Yes
Acknowledgements and errors Transmit descriptive messages
Translation mode for CR Ignore
Translation mode for LF Save as CRLF
Acknowledgement /Error message start %
O1234
Acknowledgement /Error message end M30
%
Ignore control characters other than CR-LF Yes
To set the PC in the Drip feed mode
Set Handshake to = Software
Set Drip feed = ON
Cable connection
If the PC has 9 pin connector
Null modem Full Handshake
PC
9 pin
1
2
3
4
5
6
7
8
8
2
3
20
7
6
4
5
CNC
25 pin
PC
9 pin
1
2
3
4
5
6
7
8
8
2
3
6
7
20
5
4
CNC
25 pin
If the PC has 25 pin connector
Null modem Full Handshake
PC
25 pin
8
2
3
20
7
6
4
5
8
3
2
20
7
6
4
5
CNC
25 pin
PC
25 pin
8
2
3
20
7
6
4
5
8
3
2
6
7
20
5
4
CNC
25 pin

You might also like