FOR USE BY ARCHITECTS AND ENGINEERS

SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
SEVO 1230 Clean Agent Cylinders
140057, 140069, 140079, 140107, 14817, 14813
Description
The agent storage cylinder is a steel pressure vessel manufactured, tested and stamped in accordance with DOT
4BW500 or DOT 4BA500, TC (Transport Canada).
The agent storage cylinder is designed to hold the clean agent at a normal operating pressure of 500 psi (34.5 bar)
(35.2 kg/cm) or 360 psi (25 bar) at 70F (21.1C).
The agent storage cylinders are suitable use at temperatures of 0F (-17.8C) to 130F (54.4C).
A rupture disc is connected to the cylinder body to serve as a pressure relief device to protect the cylinder against
excessive internal pressure. The disc rupture point is in the range of 864 psi (59.5 bar) to 950 psi (65.5 bar) at 70F
(21.1C).
The agent storage cylinders are available in sizes of 40 lb. (15 L), 76 lb. (29 L), 164 lb. (62 L), 322 lb. (122 L), 601
lb. (227 L), and 910 lb. (368 L) . Figure 2.1 shows the cylinder congurations, dimensions, ll ranges and other
pertinent data.
Part No. CV 140069 CV 140079 CV 14817 CV 140057 CV 14183 CV 140107
Cylinder Size lbs 40 76 164 322 601 910
Volume ft
3
0.53 1.02 2.19 4.3 8.02 13.0
L 15 29 62 122 227 368
Diptube Diameter in. 1 1/4 1 1/4 1 1/4 2 2 1/2 2 1/2
mm 35.1 35.1 35.1 52.5 62.7 62.7
Valve Outlet in. 1.0 1.0 1.25 2.5 2.5 3.0
mm 25.4 25.4 31.75 63.5 63.5 76.2
Allowable Fill lbs 16 - 40 31 - 76 66 - 164 129 - 322 241 - 601 390 - 910
kg 7 - 18 14 - 34.5 30 - 74.5 58.5 - 146 109 - 272.5 177 - 442
Weight lbs 38 52 98 220 320 448
kg 17.2 23.6 44.5 99.8 145.1 203.2
A in. 10 1/6 10 1/6 12 7/8 20 20 24 1/2
mm 255.59 255.59 327 508 508 622.3
B in 17 1/4 28 1/2 37 1/2 33 1/2 54 1/4 60 7/8
mm 438.15 723.9 952.5 842.0 1378.0 1546.2
C in 21 3/8 32 3/4 42 1/4 39 3/4 61 67 3/4
mm 543 831.9 1073.2 1010 1457.33 1720.9
Optional Liquid Level Indicator N N N Y Y Y
CV.7.7.2010
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
This page intentionally left blank
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
Electric Solenoid
SOL 21857 12 V.D.C. 0.76 AMP
SOL 21858 24 V.D.C. 0.38 AMP

Description
Electric solenoid valve is normally closed and the
valve requires electrical energy to remain open.
Opening the valve vents the pressure from the top of
the position in the cylinder valve allowing the piston to
slide upward and commence cylinder discharge. The
electric solenoid valves are available in 12 V.D.C. and
24 V.D.C. The solenoid selected must be compatible
with the output signal from the control unit.
Explosion-Proof Electric Solenoid
EX-SOL 21858 24 V.D.C. .38 AMP
Description
Explosion-proof electric solenoid valve is normally
closed and the valve requires electrical energy to
remain open. Opening the valve vents the pressure
from the top of the piston in the cylinder valve allowing
the piston to slide upward and commence cylinder
discharge. The explosion-proof electric solenoid
valves are available in 24 V.D.C. The solenoid must
be compatible with the output signal from the control
unit.
SEVO 1230 Releasing Controls
SOL 28157, SOL 21858
SOL EA45, MA 3033, PA 3000
SOL.7.7.2010
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Electric Actuator
SOL EA45 24 V.D.C.
0.2 AMP Continuous
0.6 AMP Firing
Description
An electrical current operates the internal solenoid
activating a pin that depresses the vent valve in the
top plug of the cylinder valve. Opening the valve
vents the pressure from the top of the piston in the
cylinder valve allowing the piston to slide upward and
commence cylinder discharge. The electric solenoid
actuator is available in 24 V.D.C. The solenoid
actuator must be compatible with the output signal
from the control unit.
Manual Actuator
MA3033
Description
The local Manual Actuator control head features a
local lever that depresses a Schrader valve thereby
venting the pressure for the top of the piston in the
cylinder valve. This allows the piston to slide upward
and commence cylinder discharge. The manual
actuator mounts directly on top of a Top Plug Adapter
that mounts directly on top of the cylinder valve.
Top Plug Adapter (TP 1.0):
for valves measuring 1 and 1.25
Top Plug Adapter (TP 2.5):
is used for valves measuring 2.5 and 3
SEVO 1230 Releasing Controls
SOL 21857, SOL 21858
SOL EA45, MA 3033, PA 3000
page 2
SOL.7.7.2010
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
SEVO 1230 Releasing Controls
SOL 21857, SOL 21858
SOL EA45, MA 3033, PA 3000
Description
The Pneumatic Actuator Control Head features a
pneumatically driven piston that depresses a check
valve, releasing the pressure from the top of the
piston, allowing the cylinder discharge. The pneumatic
pressure required to operate the Pneumatic Actuator
Control Head is obtained from the M port of a main
cylinder that is either mechanically and/or electrically
actuated. Multiple cylinders equipped with Pneumatic
Actuator Control Heads can be activated from one
main cylinder using 1/4metal ex hose or 1/8
pipe. The Pneumatic Actuator Control Head mounts
directly to a top plug adapter directly on top of the
cylinder valve.
Pneumatic Actuator
PA 3000
page 3
SOL.7.7.2010
Multiple Pneumatic Actuator Conguration
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
SEVO 1230 Releasing Controls
SOL 21857, SOL 21858
SOL EA45, MA 3033, PA 3000
page 4
SOL.7.7.2010
ACTUATOR OPTIONS
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
This page intentionally left blank
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
SEVO 1230 Nozzles
N-180-xx-xx-xxx
N-360-xx-xx-xxx
Description
The nozzle controls the ow and distribution in the
protected area. Five nozzle sizes are available in
aluminum: , 1, 1 , 2, and 2 . Each nozzle is
available with a 360 16 port (central) or 180 9 or 7
port (sidewall) discharge pattern. The 9 port nozzles
may only be used with FM approved systems.
Pre-engineered Nozzles
Cylinder
Size
Type
Nozzle
Size
Orice
Area
Drill
Size
Part No.
40 lb Sidewall 1 0.1963 0.1890 N180-1.0-0.1963 402
40 lb Central 1 0.1963 0.1250 N360-1.0-0.1963 401
76 lb Sidewall 1 0.4418 0.2835 N180-1.0-0.4418 402
76 lb Central 1 0.4418 0.1875 N360-1.0-0.4418 401
164 lb Sidewall 1.5 0.7854 0.3780 N180-1.5-0.7854 404
164 lb Central 1.5 0.7854 0.2500 N360-1.5-0.7854 403
322 lb Sidewall 2.0 1.4849 0.5197 N180-2.0-1.4849 406
322 lb Central 2.0 1.4849 0.3437 N360-2.0-1.4849 405
601 lb Sidewall 2.0 1.1075 0.4880 N180-2.0-1.1075 406
601 lb Central 2.0 1.1075 0.2969 N360-2.0-1.1075 405
910 lb Sidewall 2.0 2.0739 0.6088 N180-2.0-2.0739 406
910 lb Central 2.0 2.0739 0.4207 N360-2.0-2.0739 405



Engineered Nozzles
* Nozzle size is determined based on Hydraulic Flow Calculation
N 180 x.x xx xxxx
N 360 x.x xx xxxx
Orice Drill Size, Decimal Equivalent, mm
Number of Ports
Pipe Connection Size, Decimal Equivalent, inches
Available in half inch diameter increments: 1/2, 1, 1 1/2, 2 & 2 1/2
Discharge Pattern

Engineered Nozzles
Type
Nozzle
Size
No. of
Ports
Part No.
Sidewall 1/2 7 N180-0.5-7-xx
Central 1/2 16 N360-0.5-16-xx
Sidewall 1 7 N180-1.0-7-xx
Central 1 16 N360-1.0-16-xx
Sidewall 1.5 7 N180-1.5-7-xx
Central 1.5 16 N360-1.5-16-xx
Sidewall 2.0 7 N180-2.0-7-xx
Central 2.0 16 N360-2.0-16-xx
Sidewall 2.5 7 N180-2.5-7-xx
Central 2.5 16 N360-2.5-16-xx
NZ.7.7.2010
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
This page intentionally left blank
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
SEVO 1230 LIQUID LEVEL INDICATOR
LL-30020-1, LL-30020-2
Description
The SEVO 1230 LL-30020 Series Liquid Level Indicator is a simple, manually operated device, which provides
means to determine the uid level in a vertically mounted cylinder. Use of this device allows for the content of uid
to be determined without removing cylinder from its bracketing and piping for weighing.
Operation
A magnet equipped oat moves with the uid level along the stem. Level is obtained by removing protective cap
and pulling out the calibrated tape until magnet interlock with oat is felt. The weight is determined by converting
the level measurement into a weight amount using the conversion tables. The operating temperature range is 32F
to 120F (0 - 50 C).
Specications
The uid-storage cylinders of 322 lb. (122 L) capacity or larger shall provide a reliable means for determining weight
during normal routine service. The liquid level indicator shall not require additional space when cylinder is installed.
Using the LLI shall not require shutting down clean agent system or interrupting re protection. The LLI shall be
capable of eld installation with a standard wrench when cylinder is uncharged. The LLI shall be of exible tape
design, allowing use in conned spaces.
Part Number Cylinder Size (lb) Cylinder Size (L) Dimension A
LL-30020-1 322 122 21 5/8
LL-30020-2 601/910 227/368 41 1/2
LL.7.7.2010
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
This page intentionally left blank
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
SEVO 1230 PRESSURE SWITCHES
PS 37, PS 10-500
Discharge Pressure Switch
PS 37
Description
The operation pressure switch is used to provide
a means of detecting system activation. Upon
activation of the cylinder valve, the operation pressure
switches contacts transfer to indicate discharge or to
perform disconnect/activation required during system
operation.
Low Pressure Switch
PS 10-500
Description
The pressure switch monitors the pressure within the
SEVO 1230 cylinder should a loss of the nitrogen
occur. The pressure switch contacts transfer
indicating a problem. The low pressure switch is
normally wired into a supervisory circuit to give a
trouble signal upon activation.

Characteristics
0.125 27 NPT male thread 430 +10 psig actuation pressure
Temperature -65F to 275F 600 psig proof pressure 5,000 burst pressure
Contacts Silver 2AMP28VDC 375 VA 120 VAC Pilot Duty
Normally closed: Black
Normally open: Blue
Common: Violet
Characteristics
0.125 27 NPT male thread
58+psig actuation pressure
40+psig release pressure temperature -65F
250 proof pressure
5,000 burst pressure
Contacts silver 20 amps 120VAC / 240 VAC PS37
Normally open/Normally closed
Normally Open: Red
Normally Closed: Black
Common: White
PS.7.7.2010
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
This page intentionally left blank
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
SEVO 1230 Check Valves
78FP1.0, 78FP1.25, 78FP2.5, 78FP3.0
Description
Check Valves are used when two or more agent
storage cylinders are manifolded together with
one common discharge piping conguration. Their
purpose is to prevent loss of agent in the event that
any of the agent storage cylinders are not connected
to the manifold at time of system discharge.
In a full open position the 78FP rubber faced swing
clapper is held tightly against the valve body, out of
the ow steam, to provide maximum ow area and
prevention of clapper utter. The clapper design
produces quick, non-slam closure before ow reversal
can occur, which provides a leak free sealing of back
pressures as low as 1 psi (0.07 bar) equivalent to 28"
water head. (Figure 2.11b)

Pressure Rating
1" through 3" 78FP Check Valves have a maximum
working pressure of 500 psi (34.5 bar).
Installation
The 78FP UL/FM Check Valves may be installed
vertically or horizontally. For the vertical direction,
the ow direction must be upwards. In a horizontal
installation the Hinge Pin is to be located on top.
Proper installation and maintenance in accordance to
Gruvlok specications, as well as being in compliance
with the applicable standards of the National Fire
Protection Association.
78FP.7.7.2010
*
* UL/ULC Approval only for 2 1/2& 3Check Valves
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
This page intentionally left blank
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
SEVO 1230 Cylinder Straps
ST 10100, ST 10200, ST 10600, ST 10900
Description
The mounting bracket provides a means to securely
attach the cylinder to a wall or Unistrut frame channel.
They cylinder brackets are manufactured of stainless
steel band formed to the radii of the cylinders with
anges for bolting to continuous slot metal framing
channel (12 gauge steel with corrosion-resistant
paint or galvanized 1100 H Unistrut.) The channel
bracket is to be provided by the installer. The cylinder
bracket must be secured to a solid surface that will
withstand the cylinder load with the cylinder weight
oor supported. This precaution is necessary for the
bracket to safely support the weight of the cylinder and
the reaction force during discharge of the FK-5-1-12.
All cylinders must be mounted in a vertical position
and rest rmly on the oor or mounting surface.
Part Number
Brackets
Required
Cylinder
Size (lb)
Dimensions (inches)
A B C D E
ST10100 1 40 & 76 9.9 12.3 11.3 1.4 4.8
ST10200 1 164 12.7 15 14 1.4 6.5
ST10600 1 322 22.3 19.9 21.3 1.4 9.8
ST10600 2 601 22.3 19.9 21.3 1.4 9.8
ST10900 2 910 24 27 26 1.63 12.25
Part Number
Brackets
Required
Cylinder
Size (L)
Dimensions (mm)
A B C D E
ST10100 1 15 & 29 250.83 304.8 279.4 35.56 125.22
ST10200 1 62 322.58 381 355.6 35.56 165.1
ST10600 1 122 514.35 606.55 571.5 35.56 254
ST10600 2 227 514.35 606.55 571.5 35.56 254
ST10900 2 368 609.6 682.24 657.1 41.4 311.25
ST.7.7.2010
Note:
If one bracket is required, it must be centered on the
cylinder.
If two brackets are required, they must be spaced evenly
over the height of the cylinder at one-third and two-third
measurements from the oor.
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
This page intentionally left blank
FOR USE BY ARCHITECTS AND ENGINEERS
SEVO Systems
+1.913.677.1112
www.sevosystems.com
[email protected]
Technical Data Sheet
Ulizing 3M
TM
Novec
TM
1230 Fire Protecon Fluid
SEVO 1230 Flexible Discharge Hose
FH30898, FH30899, FH30900, FH30901
Flexible Discharge Hose
Size
(in.)
Type Material Coupling
Connection
to Manifold
Connection
to Valve
Working
Pressure
Bursting
Pressure
Min / Max
Temp
1
100 R1 Wire
H104 20
Hose
R1 21RE
Neoprene, Steel
Chromated
Couplings
Female Swivel
Coupling 1
1 J IC
Adapter /
1 NPT Male
Fixed Male
Coupling 1
NPT
625 psi
43 bar
2500 psi
172.4 bar
-40 / -212 F
-40 / 100 C
1 1/4
100 R1 Wire
H104 20
Hose
R1 21RE
Neoprene, Steel
Chromated
Couplings
Female Swivel
Coupling 1 1/4
1 1/4 J IC
Adapter /
1 1/4 NPT
Male
Fixed Male
Coupling 1
1/4 NPT
625 psi
43 bar
2500 psi
172.4 bar
-40 / 212 F
-40 / 100 C
2 1/2
Corrugated
Stainless
Steel Hose
Single Stainless
Steel Band
Welded Male
Couplings 2
1/2 NPT Both
Sides
2 1/2 Male
NPT
2 1/2 NPT
Union
619 psi
42.7 bar
1857 psi
128 bar
-40 / 1000 F
-40 / 437.8 C
3
Corrugated
Stainless
Steel Hose
Single Stainless
Steel Band
Welded Male
Couplings 2
1/2 NPT Both
Sides
3 Grooved
Fitting
3 Grooved
Fitting
820 psi
56.5 bar
2460 psi
169.6 bar
-40 / 1000 F
-40 / 437.8 C
Description
Flex hoses are used to connect the agent storage
containers to the manifold in multiple cylinder
arrangements. Each 1 and 1.25 diameter hose is
constructed of high pressure hydraulic rubber and
with the 2.5 diameter, a stainless steel corrugated
inner core with a stainless steel outer braid. All three
sizes are tted with male NPT threads on both ends.
The recommended assembly conguration is to install
a ex hose to the cylinder valve discharge outlet,
then install to the check valve, with the check valve
connected to the appropriate tting in the manifold.
Note: the ex hose is to be installed forming a 90
bend and attaching to the check valve. No bends of
the ex hose in excess of the gure shown to the right
are to be used at the installation.
Cylinder Size
Hose
Diameter
Hose
Length
LB L In. In. mm
40 15 1 28 711
76 29 1 28 711
164 62 1.25 28 711
322 122 2.5 29 736
601 227 2.5 29 736
910 368 3 30 762
FH.7.7.2010
Hose Diameter
1 1.25 2.5 3
A
in. 16.5 16.75 16.75 16.75
mm 419 425.5 425.5 425.5
B
in. 17.5 18 18.75 19
mm 444.5 457.2 476.3 482.6
C
in. 18.63 19.13 21.75 22
mm 478 486.8 552.5 558.8