IS EN 1992

(Eurocode 2) Design of Concrete Structures

Brian ORourke
Chartered Engineer
Department of Civil, Structural and Environmental Engineering
Cork Institute of Technology
Introduction
EUROCODE 2: DESIGN OF CONCRETE STRUCTURES is published in four parts:
IS EN 1992-1-1:2005 General Rules and Rules for Buildings
Irish National Annex due 19
th
October 2009
Replaces BS 8110-1,2,3
IS EN 1992-1-2:2005 Design of Concrete structures. Structural fire design
Irish National Annex due 19
th
October 2009
Replaces BS 8110-1,2
IS EN 19922: 2005 Design of Concrete Structures. Bridges. 2005
Irish National Annex due 30
th
October 2009
Replaces BS 5400
IS EN 19923: 2006 Design of Concrete Structures. Liquid-retaining and
containment structures
Irish National Annex due 19
th
October 2009
Replaces BS 8007
Useful Resources
www.eurocode2.info
www.concretecentre.com
I.S.E. Manual for Design of Concrete Structures to Eurocode 2
Companion Document BD 2403 U.K. Dept. of Communities
and Local Government
Designed and Detailed Eurocode 2, Concrete Society
Concrete Society / I.S.E. Standard Method of Detailing
Structural Concrete, third edition to Eurocode 2
Lecture and notes on www.ieicork.ie under downloads
Eurocode 2 Differences
1. Eurocode 2 is generally laid out to give advice on the basis of
phenomena (e.g. bending, shear etc.) rather than by member
types as in BS 8110 (e.g. beams, slabs, columns, etc)
2. Design is based on characteristic cylinder strengths not
characteristic cube strengths
3. Code does not provide derived formulae (e.g. for bending,
only the details of the stress block are expressed).
4. Units for stress are mega Pascals, MPa (1 MPa = 1 N/mm
2
)
Differences continued
5. A comma used for a decimal point
6. One thousandth is represented by
7. Axes changed x, y to y, z
8. The partial factor for steel reinforcement is 1.15. However,
the characteristic yield strength of steel that meets the
requirements will be 500 MPa; so overall the effect is
negligible
9. Higher strengths of concrete are covered up to class
C90/105. However, because the characteristics of higher
strength concrete are different, some expressions in the
Eurocode are adjusted for classes above C50/60
Differences continued
9. The variable strut inclination method is used in for the
assessment of the shear capacity of a section
10. Serviceability checks can still be carried out using deemed
to satisfy span to effective depth rules similar to BS 8110
11. The rules for determining the anchorage and lap lengths
are more complex than the simple tables in BS 8110
IS EN 1992-1-1:2005
Twelve sections:
Section 1: General
Section 2: Basis of design
Section 3: Materials
Section 4: Durability and cover to reinforcement
Section 5: Structural analysis
Section 6: Ultimate limit states
Section 7: Serviceability limit states
Section 8: Detailing of reinforcement and prestressing tendons -
General
Section 9: Detailing of members and particular rules
Section 10: Additional rules for precast concrete elements and
structures
Section 11: Lightweight aggregate concrete structures
Section 12: Plain and lightly reinforced concrete structures
Section 1 General Information
Scope of code
Principles and application
rules
Symbols
l
e
N z x A
s
' A
s
d' d b V M
BS
8110
l
0
N
Ed
z x A
s2
A
s
, A
s1
d
2
d b V
Ed
M
Ed
EC 2
Section 2 Basis of Design
Refers to IS EN 1990 / IS EN 1991 for design life, limit state
principles, actions, etc.
2.4.2.2 Partial factors for materials UK values
Section 3 Materials
Concrete: Table 3.1
Concrete Table 3.1 (extract)
4.1 3.8 3.5 3.2 2.9 2.6
f
ctm
MPa
37 36 35 34 33 31
E
cm
GPa
0.0035 0.0035 0.0035 0.0035 0.0035 0.0035
c2
60 55 50 45 37 30
f
cu
MPa
50 45 40 35 30 25
f
ck
MPa
Irish N.A. may provide data for C28/35 & C32/40
Concrete design strength Cl. 3.1.6
Poissons ratio = 0.2 Cl. 3.1.3 (4)
Coefficient of thermal expansion 10E-6/k Cl. 3.1.3 (5)
Creep / shrinkage Cl. 3.1.4
c
ck cc
cd
f
f

cc
= coefficient; 0.85 flexure & axial load, 1.0 shear
UK values: Irish N.A. may change
cc
in range 0.85 1.0
5 . 1 =
c

Steel Reinforcement Cl. 3.2.2

Ranges from 400 to 600 MPa, generally 500MPa
Bar sizes unchanged
Modulus of elasticity, Es = 200GPa
Mild steel reinforcement not covered
s
yk
yd
f
f

=
Section 4 Durability and Cover
Cl. 4.4.1.1 (2)
C
nom
= C
min
+ C
dev
C
min
= max{C
min,b
; C
min,dur
}
C
min,b
from Table 4.2 (generally bar size)
C
min,dur
from BS 8500 UK: IRISH N.A. & IS EN 206
C
dev
= 10mm UK N. A.
Cover for Fire Protection
EN 1992-1-2 Typical dimensions / axis distance to satisfy fire resistance
Fire
Resistance
Beam One-way solid slab Braced column
Simply
Supported
b min /a (mm)
Continuous
b min /a
(mm)
Simply
Supported
h min /a (mm)
Continuous
h min /a
(mm)
Exposed on
one side
b min /a
(mm)
Exposed on
more that one
side
b min /a (mm)
R60 120/40
160/35
200/30
300/25
120/25
200/12
80/20 80/10 155/25 250/46
350/40
R90 150/55
200/45
300/40
400/35
150/35
250/25
100/30 100/15 155/25 350/53
450/40
R120 200/65
240/65
300/55
500/50
200/45
300/35
450/35
500/30
120/40 200/20 175/35 350/57
450/51
R240 280/90
350/80
500/75
700/70
280/75
500/60
650/60
700/50
175/65 280/40 295/70
Notes
bmin, hmin= beam or column width

a = axis distance, generally distance to centre of reinforcing bar



Section 5 Structural Analysis
5.1.1 Common idealisations of the behaviour used for analysis
are:
linear elastic behaviour (Cl. 5.4)
linear elastic behaviour with limited redistribution (Cl. 5.5)
plastic behaviour at ULS including strut and tie models (Cl. 5.6)
non-linear behaviour (Cl. 5.7)
5.2 Geometric imperfections
Structure assumed to be out of plumb with
inclination of 1/200. Analysis must include an
equivalent horizontal load acting with the other
actions such as wind
5.8 second order effects with axial loads (columns)
5.1.3(1) permits analysis based on either:
(a) Alternate spans carrying the design
variable and permanent load , and
other spans carrying the permanent
load
(b) Any two adjacent spans carrying the
variable and permanent load, and all
other spans carrying only the design
permanent load
UK NA recommends (a), which leads
to three load cases considered
Load Cases and Combinations
Continuous Beams
Floor slab simplification
UK N.A. recommends
analysis based on all spans
loaded where:
(a) For one way spanning
slabs with bay areas > 30m
2
(b) Ratio of variable to
permanent load 1.25
(c) Characteristic variable load
does not exceed 5 kN/m
2
excluding partitions
NCCI: Concrete Centre: Concise Eurocode
Effective Width of Flanges
5.3.2.1
The effective flange width b
eff
for
T and L beams is determined
from:
Effective Span of Beams and Slabs
5.3.2.2 The effective span l
eff
of a beam or slab is:
Generally the lesser of:
Clear span + h/2 or
Clear span + t/2
Where t is the width of the support
Extract Figure 5.4
Section 6 Ultimate Limit State
Bending with or without axial force
6.1 (2)
Assumptions
Plane sections remain plane after bending so that:
(a) the strains are linearly proportional to the distance to the neutral axis and
(b) the strain in the concrete is equal to the strain in the reinforcement at the
same depth in the section
The tensile strength of the concrete is ignored and no
contribution is taken for the concrete below the neutral axis
in tension
Strain distribution at ULS
Range of possible strain
distributions

cu2
6.1(2)P Stress in the reinforcement
The stress in the
reinforcement is
derived from its stress-
strain curve given in
Figure 3.8
E
s
= 200 GPa

uk = 0.05
Stress MPa
Strain

ud
Idealised design
curves
Where: f
t
= tensile strength of the reinforcement
f
yk
= yield strength of the reinforcement
Idealised
s yd yd
E f =
Figure 3.8
0022 . 0
) 15 . 1 * 3 * 200 /( 500
=
=
=
E
E f
s yd yd

yd
f
yk
f
6.1 (3)P Stress in the concrete
The ultimate strain in
the concrete is

cu2
= 0.0035 from
Table 3.1
The stress in the
concrete is obtained
from the stress-strain
curve Figure 3.3
Figure 3.3

c
ck
f

85 . 0

c1
= 0.002
cu
=

0.0035

Stress MPa
Strain

cu2
= 0.0035 Strain
c2
= 0.002
Singly reinforced beams rectangular parabolic stress
block
Neutral axis
x

cu2
= 0.0035
d
b
A
s
Strains at ULS
Figure 6.1
for use
Concrete stress at
ULS
Section
c
ck
f

85 . 0
EC2 Rectangular Stress Block Cl. 3.1.7 Figure 3.5
Singly Reinforced Sections
Design Equations

Moment of resistance based on concrete reaching ULS








for equilibrium at ULS R Ed
M M =
Let



And let




Hence

Therefore

ck
Ed
f bd
M
k
2
=
4 . 0
z d
x

=
2
Which is a quadratic equation in terms of With the positive roof of:



Which is an equation for the lever arm in terms of and

The area of steel reinforcement required to resist can be derived from:



With

Therefore:


Z f
M
A
yk
Ed
s
87 . 0
=
Z A
f
Z F M
s
m
yk
t Ed

= =
Summary: Design Equations







k
Z f
M
A
yk
Ed
s
87 . 0
=
ck
Ed
f bd
M
k
2
=
Limit on k
These derived equations can be used to design the reinforcement in a singly
reinforced beam subject to the limits on the lever arm of:

1. Balanced design , which limits as a minimum
2. Maximum (5.6.3(2)), which limits as a minimum

These limits expressed in terms of k are:

1. Balanced design substitutes to give:



Which solves for maximum

2. Maximum
solves for maximum


It is also good practice to avoid failure by premature crushing of weak
concrete near the top of the section as a maximum

Doubly Reinforced Beams
For the EC2 limit the equilibrium of forces is:

Equation A









Equation B

By multiplying both sides of Equation A by and
rearranging gives



With


Equation C
Substitution of

into Equation B and Equation C converts them to



And








1
Shear
Section 6.2
The strut inclination method is used for shear capacity checks
The shear is resisted by concrete struts in compression and
shear reinforcement acting in tension
Shear formulae expressed in terms of force rather than stress
Designer free to choose a strut angle 22
o
45
o
BO1
Slide 38
BO1
Brian O'Rourke, 12/10/2009
Strut Inclination Method
notation
Design equations are derived as follows:

The maximum design strength of the concrete strut

= Ultimate design strength x cross-sectional area



And its vertical component



this is the maximum vertical shear that can be resisted
by the concrete strut,

Trigonometrical conversion yields:


In EC2 this equation is modified by a strength
reduction, factor for concrete cracked in shear:


And

Therefore:

When the design shear force, exceeds
shear links must be provided.
Their area and spacing is obtained by taking a
method of sections cut at x-x

The vertical shear force in the link, is:







If the links are spaced at s then the force in each link
is proportionately:


The shear resistance must equal the shear
applied hence and by rearrangement:



EC2 minimum links are:



For minor members that do not require shear
reinforcement the shear capacity is given by an
empirical equation:


With a minimum value of:


Where




is taken from Figure 6.3 in EC2






Shear Formulae Summary
But not less than
Suggested Design Procedure for Shear
1. Determine
2. Calculate the concrete compressive strut capacity for from:



3. If proceed to step 6
4. If check that the strut angle lies between 22
o
and 45
o
by
calculating
5. Determine the strut angle from:



6. Determine the area and spacing of the shear links from:



7. Check minimum links from:



8. Check link spacing maximum

9. Calculate additional longitudinal force in tension reinforcement.
Strut angle choice 22
0
- 45
0
Cl. 6.4 Punching Shear
Basic control perimeter radius at corners
Located at 2d form the face of the loaded area
Section 7 S.L.S.
The serviceability limit state of deflection can be checked using span-
effective depth ratios. A more rigorous approach is possible but is seldom
used in practice. the verification equation is:



Where:






Where:


N = Basic span-effective depth factor
K = Element typefactor
F1 = Flange beam factor
F2 = Brittle finishes factor
F3 = reinforcement stress factor
Cl. 7.4 SLS Deflection

Columns
Sections 5.8 & 6.1
Design more complex than BS 8110
Braced / Unbraced
Geometric imperfections must be included in M
Ed
Procedure is to:
Determine the slenderness ratio,
Determine the limiting slenderness,
lim
Design for axial load and first order moments
Include for second order effects where they occur
Cl 5.8.3.2 Column Slenderness,
Concise Eurocode / I.S.E. / BS 8110
Limiting slenderness
lim
Columns where
lim
and Braced
Design for N
Ed
and M
Ed
5.8.8 Nominal curvature method:
M
Ed
= M
0Ed
+ N
Ed
e
i
M
0Ed
= the larger end moment from analysis
e
i
= the eccentricity due to geometric imperfection from
5.2(7)
With a minimum eccentricity = h/30 or 20mm from 6.1(4)
Solve using equilibrium of forces or column design charts
200 /
2
0
l
l
e
i
i
i
=

Columns where
lim
and Braced
Design for N
Ed
and M
Ed
5.8.8 Nominal curvature method:
M
Ed
= maximum of
(i) M
02
(ii) M
0Ed
+ M
2
(iii) M
01
+0.5M
2
M
0Ed
is the equivalent first order moment
including the effect of imperfections at
about mid-span height of the column,
given as:
M
0Ed
= (0.6 M
02
+ 0.4M
01
) 0.4M
02
Exp 5.32
M
2
is the nominal 2
nd
order moment, given
as :
M
2
= N
Ed
e
2
e
2
= deflection curvature from Exp 5.33
Again solve using equilibrium of forces
or column design charts
ULS Strain distribution Figure 6.1
for solution by equilibrium
Figure 6.1 column strain relationships
Column Design Charts: NCCI Concrete Centre / I.S.E
Column Design Example
Loading g
k
roof = 3.0 kN/m
2
g
k
floor = 4.5 kN/m
2
q
k
roof = 0.6 kN/m
2
q
k
floor = 4.0 kN/m
2
Main beams 600 mm deep x 300 mm wide
Other beams 400 mm deep x 300 mm wide
Columns 450 mm square
f
ck
= 40 MPa f
yk
= 500 MPa
Assume pinned foundations and structure braced
Thank you for your attention
[email protected]
[email protected]