Scribd
Upload
1K views

Multiuser Connection - For Cisco Packet Tracer Activity

Activity for multi-user connection, setting up the LAN for 2PC, and pinging the IP address of both PCs

Uploaded by

catipztipz
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
1K views

Multiuser Connection - For Cisco Packet Tracer Activity

Activity for multi-user connection, setting up the LAN for 2PC, and pinging the IP address of both PCs

Uploaded by

catipztipz
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

MULTIUSER CONNECTION

PROCEDURE:
1. OPEN 2 SET OF PACKET TRACER AND PUT ON BOTH SIDE
2. SETUP THE FOLLOWING DEVICES ON BOTH SIDE,
- ROUTER-PT (GENERIC)
- SWITCH (2960)
- PC (2 PIECES)
- COPPER STRAIGHT-THRU, CONNECT ( ROUTER TO SWITCH, SW. TO PC-0, SW. TO
PC-1) USED FASTETHERNET
3. CLICK PLACE NOTE (N), CLICK ON PACKET AND TYPE (LAN 1
192.168.1.0),
4. ON SEPARATE PACKET TYPE IP ADDRESS AT PC0 (192.168.1.2), PC1 (192.168.1.3) &
ROUTER(192.168.1.254)
5. CLICK ROUTER, GO TO CLI, TYPE THE FF.
- No
- Enable
- Configure terminal
- Interface fastEthernet 0/0
- Ip address 192.168.1.254 255.255.255.0
- No shutdown
- CLICK X(CLOSE)
6. CLICK PC0, GO TO DESKTOP, IP CONFIGURATION / STATIC AND TYPE THE FF.
PC0
IP ADDRESS
:
192.168.1.2 CLICK SUBNET MASK
DEFAULT GATEWAY :
192.168.1.254
PC1
IP ADDRESS
:
192.168.1.3 CLICK SUBNET MASK
DEFAULT GATEWAY :
192.168.1.254
CLOSE ALL
7. ON SEPARATE PACKET TRACER DO THE FF.
8. CLICK PLACE NOTE (N), CLICK ON PACKET AND TYPE (LAN 2
192.168.2.0),
9. ON SEPARATE PACKET TYPE IP ADDRESS AT PC0 (192.168.2.2), PC1 (192.168.2.3) &
ROUTER(192.168.2.254)
10.CLICK ROUTER, GO TO CLI, TYPE THE FF.
- No
- Enable
- Configure terminal
- Interface fastEthernet 0/0
- Ip address 192.168.2.254 255.255.255.0
- No shutdown
- CLICK X(CLOSE)
11.CLICK PC1, GO TO DESKTOP, IP CONFIGURATION / STATIC AND TYPE THE FF.
PC0
IP ADDRESS
:
192.168.2.2 CLICK SUBNET MASK
DEFAULT GATEWAY :
192.168.2.254
PC1
IP ADDRESS
:
192.168.2.3 CLICK SUBNET MASK
DEFAULT GATEWAY :
192.168.2.254
CLOSE ALL
12.AT PACKET TRACER, CLICK EXTENSIONS / MULTIUSER / PORT VISIBILITY
13.AT ROUTER, CHECK SERIAL 2/0 ON BOTH PACKET TRACER
14.AT LAN 1, ADD & CLICK MULTIUSER CONNECTION (CLOUD IMAGE)
15.CLICK CONNECTION, CHOOSE & CLICK SERIAL DTE
16.CLICK TO ROUTER & CHOOSE SERIAL 2/0, THEN CLICK THE PEER0(CLOUD)
17.AT LAN 2, GO TO EXTENSIONS / LISTENS / DELETE THE PASSWORD, OK
18.CLICK PEER0(MULTIUSER)
19.AT CONNECTION TYPE , CHOOSE OUTGOING
20.AT PEER NETWORK NAME, TYPE EXACTLY THIS , LAN 1 a LAN 2

21.CLICK CONNECT / YES


22.NEW CLOUD WILL SHOWN.
23.AT LAN 2 , CLICK CONNECTION, CHOOSE SERIAL DCE
24.CLICK ROUTER / CLICK SERIAL 2/0, CLICK THE NEW CLOUD & CHOOSE THE FIRST LINE
25.AT LAN 1, CLICK THE ROUTER, TYPE ON CLI
- EXIT
- Interface serial 2/0
- Ip address 192.168.3.1 255.255.255.0
- No shutdown
- CLICK X(CLOSE)
- BESIDE AT ROUTER TYPE
S2/0 192.168.3.1
26.AT LAN 2, CLICK THE ROUTER, TYPE ON CLI
- EXIT
- Interface serial 2/0
- Ip address 192.168.3.2 255.255.255.0
- No shutdown
- CLICK X(CLOSE)
- BESIDE AT ROUTER TYPE
S2/0 192.168.3.2
27.CLICK AGAIN THE ROUTER AT LAN 1 & TYPE
- EXIT
- Configure terminal
- @ router(config-router)#router rip
- Version 2
- Network 192.168.1.0
- Network 192.168.2.0
- Network 192.168.3.0
- Exit
- @ router(config)#interface serial 2/0
- Clock rate 9600
- Exit
- CLICK X(CLOSE)
28.CLICK AGAIN THE ROUTER AT LAN 2 & TYPE
- EXIT
- Configure terminal
- @ router(config-router)#router rip
- Version 2
- Network 192.168.1.0
- Network 192.168.2.0
- Network 192.168.3.0
- Exit
- @ router(config)#interface serial 2/0
- Clock rate 9600
- Exit
- CLICK X(CLOSE)
29.At LAN 1 & LAN 2 @ PEER0(CLOUD) TYPE USING PLATE NOTE THE IP ADDRESS
- 192.168.3.0
30. PING THE IP ADDRESS OF PC0 & PC1 OF BOTH SIDE
31.IF PING WAS REPLY , THEN

CONGRATS IT IS DONE

You might also like