Chapter03.

qxd

7/14/98

1:25 PM

Page 189

SECTION 3.6 INVERTERS

189

Pulse-Width Modulation Inverters

Pulse-width modulation is the process of modifying the width of the pulses in a pulse
train in direct proportion to a small control signal; the greater the control voltage, the
wider the resulting pulses become. By using a sinusoid of the desired frequency as the
control voltage for a PWM circuit, it is possible to produce a high-power waveform
whose average voltage varies sinusoidally in a manner suitable for driving ac motors.
The basic concepts of pulse-width modulation are illustrated in Figure 355.
Figure 355a shows a single-phase PWM inverter circuit using IGBTs. The states of
IGBT1 through IGBT4 in this circuit are controlled by the two comparators shown in
Figure 355b.
A comparator is a device that compares the input voltage vin(t) to a reference signal and turns transistors on or off depending on the results of the test. Comparator A
compares vin(t) to the reference voltage vx(t) and controls IGBTs T1 and T2 based on the
results of the comparison. Comparator B compares vin(t) to the reference voltage vy(t)
and controls IGBTs T3 and T4 based on the results of the comparison. If vin(t) is greater
than vx(t) at any given time t, then comparator A will turn on T1 and turn off T2.
Otherwise, it will turn off T1 and turn on T2. Similarly, if vin(t) is greater than vy(t) at any
given time t, then comparator B will turn off T3 and turn on T4. Otherwise, it will turn
on T3 and turn off T4. The reference voltages vx(t) and vy(t) are shown in Figure 355c.
LS
+
+

T1

Threephase
inverter

T2
D1

VS
2

T3
D2

D3

VS
a

Rectifier

b
c

T1

VS
2

T5
D4

(a)
FIGURE 354
(a) A three-phase voltage source inverter using power transistors.

T6
D5

D6

Chapter03.qxd

7/14/98

190

1:25 PM

Page 190

CHAPTER 3 INTRODUCTION TO POWER ELECTRONICS

T1

T4

T5
T3

va(t)

T1

T2

T5

T6

T3

T2
T6

VS
t

VS
vb(t)

VS
t

VS
vc(t)

VS
t

VS
vab(t)

2VS
VS
t

0
VS
2VS
vbc(t) 2VS
VS

0
VS
2VS
vca(t) 2VS
VS

0
VS
2VS
(b)
FIGURE 354 (concluded)
(b) The output phase and line voltages from the inverter.

Chapter03.qxd

7/14/98

1:25 PM

Page 191

SECTION 3.6 INVERTERS

191

vB1

T1

vB3

T3

vload(t)

+
Load

VDC
+
vB2

+
vu(t)

T2

vv(t)

vB4

T4

FIGURE 355
The basic concepts of pulse-width modulation. (a) A single-phase PWM circuit using IGBTs.

To understand the overall operation of this PWM inverter circuit, see what happens when different control voltages are applied to it. First, assume that the control voltage is 0 V. Then voltages vu(t) and vv(t) are identical, and the load voltage out of the
circuit vload(t) is zero (see Figure 356).
Next, assume that a constant positive control voltage equal to one-half of the peak
reference voltage is applied to the circuit. The resulting output voltage is a train of
pulses with a 50 percent duty cycle, as shown in Figure 357.
Finally, assume that a sinusoidal control voltage is applied to the circuit as shown
in Figure 358. The width of the resulting pulse train varies sinusoidally with the control voltage. The result is a high-power output waveform whose average voltage over
any small region is directly proportional to the average voltage of the control signal in
that region. The fundamental frequency of the output waveform is the same as the frequency of the input control voltage. Of course, there are harmonic components in the
output voltage, but they are not usually a concern in motor-control applications. The
harmonic components may cause additional heating in the motor being driven by the
inverter, but the extra heating can be compensated for either by buying a specially
designed motor or by derating an ordinary motor (running it at less than its full rated
power).
A complete three-phase PWM inverter would consist of three of the single-phase
inverters described above with control voltages consisting of sinusoids shifted by 120
between phases. Frequency control in a PWM inverter of this sort is accomplished by
changing the frequency of the input control voltage.

Chapter03.qxd

192

7/14/98

1:25 PM

Page 192

CHAPTER 3 INTRODUCTION TO POWER ELECTRONICS

vin(t)

vB1(t)

Comparator A

vx(t)

vB1

vB

vin > vx

On

Off

vin < vx

Off

On

Comparator B
vB3

vy(t)

vB2(t)

vB3(t)

vB4

vin > vy

Off

On

vin < vy

On

Off

vB (t)
4

(b)
vx(t)

vy(t)

(c)
FIGURE 355 (concluded)
(b) The comparators used to control the on and off states of the transistors. (c) The reference voltages used
in the comparators.

A PWM inverter switches states many times during a single cycle of the resulting output voltage. At the time of this writing, reference voltages with frequencies as
high as 12 kHz are used in PWM inverter designs, so the components in a PWM
inverter must change states up to 24,000 times per second. This rapid switching means
that PWM inverters require faster components than CSIs or VSIs. PWM inverters need
high-power high-frequency components such as GTO thyristors, IGBTs, and/or power
transistors for proper operation. (At the time of this writing, IGBTs have the advantage
for high-speed, high-power switching, so they are the preferred component for building
PWM inverters.) The control voltage fed to the comparator circuits is usually imple-

Chapter03.qxd

7/14/98

1:25 PM

Page 193

SECTION 3.7 CYCLOCONVERTERS

vx(t)

vin = 0

193

vy(t)

vu(t)

VDC

t
vv(t)

VDC

vload (t)
Vload = vv vu

vload (t) = 0

FIGURE 356
The output of the PWM circuit with an input voltage of 0 V. Note that vu(t) = vv(t), so vload(t) = 0.

mented digitally by means of a microcomputer mounted on a circuit board within the

PWM motor controller. The control voltage (and therefore the output pulse width) can
be controlled by the microcomputer in a manner much more sophisticated than that
described here. It is possible for the microcomputer to vary the control voltage to

Chapter03.qxd

7/14/98

194

1:25 PM

Page 194

CHAPTER 3 INTRODUCTION TO POWER ELECTRONICS

vx(t)

vy(t)

vin
t

vu(t)

VDC

t
vv(t)

VDC

t
vload (t)
Vload = vv vu
VDC

VDC
FIGURE 357
The output of the PWM circuit with an input voltage equal to one-half of the peak comparator voltage.

achieve different frequencies and voltage levels in any desired manner. For example,
the microcomputer could implement various acceleration and deceleration ramps, current limits, and voltage-versus-frequency curves by simply changing options in software.
A real PWM-based induction motor drive circuit is described in Section 7.10.

vload (t)

VDC

vv (t)

FIGURE 358
The output of the PWM circuit with a sinusoidal control voltage applied to its input.

1:25 PM

VDC

vin(t)

7/14/98

vu(t)

vy(t) vx(t)

Chapter03.qxd
Page 195

195