Scribd
Upload
25 views

TITLE: Diodes, Rectifier, Clipper, Clamper CKT Objective:: Item Quantity

This document outlines an experiment on diodes, rectifiers, clippers, and clampers. The objectives are to examine the characteristics and build circuits using diodes for rectification, clipping, and clamping. The equipment needed includes an oscilloscope, multimeter, function generator, and various resistors, diodes, and capacitors. Pre-lab questions are provided to help understand how to construct the circuits and predict output waveforms. Guidelines explain how to set up and test positive peak shunt clipper, positive peak series clipper, and negative clamper circuits. Output waveforms are to be observed at different frequencies and component values. Conclusions are to be drawn on the observations.

Uploaded by

HafizHumble
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
25 views

TITLE: Diodes, Rectifier, Clipper, Clamper CKT Objective:: Item Quantity

This document outlines an experiment on diodes, rectifiers, clippers, and clampers. The objectives are to examine the characteristics and build circuits using diodes for rectification, clipping, and clamping. The equipment needed includes an oscilloscope, multimeter, function generator, and various resistors, diodes, and capacitors. Pre-lab questions are provided to help understand how to construct the circuits and predict output waveforms. Guidelines explain how to set up and test positive peak shunt clipper, positive peak series clipper, and negative clamper circuits. Output waveforms are to be observed at different frequencies and component values. Conclusions are to be drawn on the observations.

Uploaded by

HafizHumble
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

KE 28101 Engg.

LAB-1

Lab-2

TITLE: Diodes, rectifier, clipper, clamper ckt


OBJECTIVE:
To examine the characteristics of diodes rectifier, clipper and clamper circuit.

EQUIPMENT/COMPONENT LIST
Item
Oscilloscope
Digital multimeter
Function Generator
Resistors : 1k, 10k 100k
Diodes :
1N4004 (p)/equivalent
1N4148 (s)/equivalent

Quantity
1
2
1
1
1
1

Capacitor :
0.1 F
1 F
100 F

1
1
1

Page 1 of 6
School of Engineering & IT, UMS

KE 28101 Engg.

LAB-1

Lab-2

Name: _____________________
Student ID:_____________________
Section:_____________________
Date:_____________________

Diodes Pre-lab:
1. You have input and output wave form like as follows:
a) How to construct the circuits?

Page 2 of 6
School of Engineering & IT, UMS

KE 28101 Engg.

2.

LAB-1

Lab-2

Draw the output waveform using the following circuits.

3. Draw the output waveform using the following circuits.

Page 3 of 6
School of Engineering & IT, UMS

KE 28101 Engg.

LAB-1

Lab-2

Diodes Guide
CLIPPER/CLAMPER
a. Parts Required:
1- 1N4004 or equivalent
1- 1N4148 or equivalent
1- 100 k Resistor
1- l0k Resistor
1- 0.1F Capacitor
b. Procedure:
1. Connect the positive peak shunt clipper circuit shown and superimpose the output waveform on
the input waveform and study the result.

2.
Replace the lN914/1N4148 switching diode with the 1N2070/1N4004 rectifier diode and study
the result.
3.

Change the input to a square-wave and repeat steps 1 and 2

4.

Lower the frequency to 1 KHz and repeat steps 1, 2, and 3.

5.

Change the circuit to a positive peak series clipper and repeat step 1-4.

6.

Connect the negative damper shown and superimpose the output waveform on the input
waveform and study the result

.
7.

Change the frequency of the input and study the result.

8.

Replace the 100 K-resistor with the l0 K-resistor and repeat steps 6 and 7.

Page 4 of 6
School of Engineering & IT, UMS

KE 28101 Engg.

LAB-1

Lab-2

9. The following figure after insertion of different value of capacitors and resistors analyze its output
waveform applying different frequency input signal.

c. Conclusion
What conclusions can be drawn from your observations in step 1- 9?

Page 5 of 6
School of Engineering & IT, UMS

KE 28101 Engg.

LAB-1

Lab-2

UNIVERSITI MALAYSIA SABAH


SEKOLAH KEJURUTERAAN DAN TEKNOLOGI MAKLUMAT
KE28101 Makmal Kejuruteraan 2

LAB # 1

DIODES Rectifier, clipper/clamper

Name:

Group Members:

Section:

Date:

Page 6 of 6
School of Engineering & IT, UMS

You might also like